XSEU-A-1202__ X on-off series for Europe Market

XSEU-A-1202__ X on-off series for Europe Market
XSEU-A-1202
SERVICE MANUAL
MIDEA AIRCONDITIONER
EUROPE MARKET
SPLIT WALL-MOUNTED TYPE
X ON-OFF SERIES
CONTENTS
1. Precaution .............................................................................................................................................. 1
1.1 Safety Precaution .......................................................................................................................... 1
1.2 Warning ......................................................................................................................................... 1
2. Function.................................................................................................................................................. 6
3. Dimension............................................................................................................................................... 9
3.1 Indoor Units ................................................................................................................................... 9
3.2 Outdoor Units .............................................................................................................................. 11
4. Refrigerant Cycle Diagram................................................................................................................... 12
5. Wiring Diagram..................................................................................................................................... 13
5.1 Indoor Units ................................................................................................................................. 13
5.2 Outdoor Units .............................................................................................................................. 15
6. Installation details ................................................................................................................................ 19
6.1 Wrench torque sheet for installation ........................................................................................... 19
6.2 Connecting the cables................................................................................................................. 19
6.3 Pipe length and the elevation ...................................................................................................... 20
6.4 Installation for the first time ......................................................................................................... 22
6.5 Adding the refrigerant after running the system for many years ................................................. 25
6.6 Re-installation while the indoor unit need to be repaired............................................................ 26
6.7 Re-installation while the outdoor unit need to be repaired ......................................................... 28
7. Operation characteristics .................................................................................................................... 31
8. Electronic function ............................................................................................................................... 32
8.1 Abbreviation................................................................................................................................. 32
8.2 Display function ........................................................................................................................... 32
8.3 Main Protection ........................................................................................................................... 34
9. Troubleshooting ................................................................................................................................... 47
9.1 Indoor unit error display .............................................................................................................. 47
9.2 Diagnosis and Solution ............................................................................................................... 48
1. Precaution
1.1 Safety Precaution
n
To prevent injury to the user or other people and property damage, the following
instructions must be followed.
n
Incorrect operation due to ignoring instruction will cause harm or damage.
n
Before service unit, be sure to read this service manual at first.
1.2 Warning
Ø Installation
n
Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated
circuit.
There is risk of fire or electric shock.
n
For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized
service center.
Do not disassemble or repair the product, there is risk of fire or electric shock.
n
Always ground the product.
There is risk of fire or electric shock.
n
Install the panel and the cover of control box securely.
There is risk of fire of electric shock.
n
Always install a dedicated circuit and breaker.
Improper wiring or installation may cause fore or electric shock.
n
Use the correctly rated breaker of fuse.
There is risk of fire or electric shock.
n
Do not modify or extend the power cable.
There is risk of fire or electric shock.
n
Do not install, remove, or reinstall the unit by yourself(customer).
There is risk of fire, electric shock, explosion, or injury.
n
Be caution when unpacking and installing the product.
Sharp edges could cause injury, be especially careful of the case edges and the fins on the
1
condenser and evaporator.
n
For installation, always contact the dealer or an Authorized service center.
There is risk of fire, electric shock, explosion, or injury.
n
Do not install the product on a defective installation stand.
It may cause injury, accident, or damage to the product.
n
Be sure the installation area does not deteriorate with age.
If the base collapses, the air conditioner could fall with it, causing property damage, product failure,
and personal injury.
n
Do not let the air conditioner run for a long time when the humidity is very high and a
door or a window is left open.
Moisture may condense and wet or damage furniture.
n
Take care to ensure that power cable could not be pulled out or damaged during
operation.
There is risk of fire or electric shock.
n
Do not place anything on the power cable.
There is risk of fire or electric shock.
n
Do not plug or unplug the power supply plug during operation.
There is risk of fire or electric shock.
n
Do not touch (operation) the product with wet hands.
There is risk of fire or electric shock.
n
Do not place a heater or other appliance near the power cable.
There is risk of fire and electric shock.
n
Do not allow water to run into electric parts.
It may cause fire, failure of the product, or electric shock.
n
Do not store or use flammable gas or combustible near the product.
There is risk of fire or failure of product.
n
Do not use the product in a tightly closed space for a long time.
Oxygen deficiency could occur.
n
When flammable gas leaks, turn off the gas and open a window for ventilation before
turn the product on.
Do not use the telephone or turn switches on or off.
2
There is risk of explosion or fire.
n
If strange sounds, or small or smoke comes from product. Turn the breaker off or
disconnect the power supply cable.
There is risk of electric shock or fire.
n
Stop operation and close the window in storm or hurricane. If possible, remove the
product from the window before the hurricane arrives.
There is risk of property damage, failure of product, or electric shock.
n
Do not open the inlet grill of the product during operation. (Do not touch the electrostatic
filter, if the unit is so equipped.)
There is risk of physical injury, electric shock, or product failure.
n
When the product is soaked (flooded or submerged), contact an Authorized service
center.
There is risk of fire or electric shock.
n
Be caution that water could not enter the product.
There is risk of fire, electric shock, or product damage.
n
Ventilate the product from time to time when operating it together with a stove, etc.
There is risk of fire or electric shock.
n
Turn the main power off when cleaning or maintaining the product.
There is risk of electric shock.
n
When the product is not be used for a long time, disconnect the power supply plug or
turn off the breaker.
There is risk of product damage or failure, or unintended operation.
n
Take care to ensure that nobody could step on or fall onto the outdoor unit.
This could result in personal injury and product damage.
Ø CAUTION
n
Always check for gas (refrigerant) leakage after installation or repair of product.
Low refrigerant levels may cause failure of product.
n
Install the drain hose to ensure that water is drained away properly.
A bad connection may cause water leakage.
n
Keep level even when installing the product.
3
It can avoid vibration of water leakage.
n
Do not install the product where the noise or hot air from the outdoor unit could damage
the neighborhoods.
It may cause a problem for your neighbors.
n
Use two or more people to lift and transport the product.
Avoid personal injury.
n
Do not install the product where it will be exposed to sea wind (salt spray) directly.
It may cause corrosion on the product. Corrosion, particularly on the condenser and evaporator fins,
could cause product malfunction or inefficient operation.
Ø Operational
n
Do not expose the skin directly to cool air for long periods of time. (Do not sit in the
draft).
This could harm to your health.
n
Do not use the product for special purposes, such as preserving foods, works of art, etc.
It is a consumer air conditioner, not a precision refrigerant system.
There is risk of damage or loss of property.
n
Do not block the inlet or outlet of air flow.
It may cause product failure.
n
Use a soft cloth to clean. Do not use harsh detergents, solvents, etc.
There is risk of fire, electric shock, or damage to the plastic parts of the product.
n
Do not touch the metal parts of the product when removing the air filter. They are very
sharp.
There is risk of personal injury.
n
Do not step on or put anything on the product. (outdoor units)
There is risk of personal injury and failure of product.
n
Always insert the filter securely. Clean the filter every two weeks or more often if
necessary.
A dirty filter reduces the efficiency of the air conditioner and could cause product malfunction or
damage.
n
Do not insert hands or other object through air inlet or outlet while the product is
4
operated.
There are sharp and moving parts that could cause personal injury.
n
Do not drink the water drained from the product.
It is not sanitary could cause serious health issues.
n
Use a firm stool or ladder when cleaning or maintaining the product.
Be careful and avoid personal injury.
n
Replace the all batteries in the remote control with new ones of the same type. Do not
mix old and mew batteries or different types of batteries.
There is risk of fire or explosion.
n
Do not recharge or disassemble the batteries. Do not dispose of batteries in a fire.
They may burn of explode.
n
If the liquid from the batteries gets onto your skin or clothes, wash it well with clean
water. Do not use the remote of the batteries have leaked.
The chemical in batteries could cause burns or other health hazards
The designs, and information in this book are subject to change without notice for product improvement.
5
2. Function
Model Names of Indoor/Outdoor Units
Series
Capacity
Indoor units
Outdoor units
7k
MSX-07HRN1-QC2
MOA-07HN1-QC2
MSX-09HRN1-QC2
MOA-09HN1-QC2
MSX-09HRN1-QC2
MOA1-09HN1-QC2
MSX-12HRN1-QC2
MOB1-12HN1-QC2
MSX-12HRN1-QC2
MOB-12HN1-QC2
18k
MSX-18HRN1-QC2
MOF-18HN1-QC2
21k
MSX-21HRN1-QB8W
MOF1-21HN1-QB8W
24k
MSX-24HRN1-QB8W
MOF3-24HN1-QB8W
9k
On-Off
12k
6
Indoor units
LCD display
Operation by remote controller.
Golden fin (Optional)
Anti-freezing control in cooling
Prevent the water being frozen on evaporator by
checking the evaporator pipe temperature
Ionizer/Plasma(optional)
Time Delay Safety control
Sleep mode auto control
Indoor fan speed control
Turbo wind, high, med, low, breeze.
Follow me
Two-direction air vane
The unit will decide the louver direction according
to operation mode.
Independent dehumidification
Self-diag. function
Anti-cold function
The function is usually used in rainy
days in springtime or damp areas.
Prevent the cold wind at the
beginning of unit start.
Auto defrost
Air flow Direction
The louver can be set at the desired position
or swing up and down automatically
Auto-restart
Auto mode
Flexible wiring connection
Temp. Compensation
7
Outdoor units
Power relay control
Low noise air flow system
Anti-rust cabinet
Made from electrolytic zinc steel sheet and anti-rust coated components.
Valve protection cover
It protects the valves and prevents water from dripping.
8
3. Dimension
3.1 Indoor Units
Figure 1:
Figure 2:
9
Figure 3:
Figure 4:
Figure
Figure 1
Figure 2
Figure 3
Figure 4
Models
MSX-07HRN1-QC2
MSX-09HRN1-QC2
MSX-12HRN1-QC2
MSX-18HRN1-QC2
MSX-21HRN1-QB8W
MSX-24HRN1-QB8W
10
W
D
H
710
195
250
790
195
265
850
225
305
998
235
322
3.2 Outdoor Units
More than 30cm
More than 60cm
(Service space
More than 30cm
Fen
obs ce or
tac
les
More than 60cm
More than 70cm
Model
W
D
H
W1
A
B
700
240
540
757
458
250
780
250
540
843
549
276
845
320
700
908
560
335
MOA-07HN1-QC2
MOA1-09HN1-QC2
MOA-09HN1-QC2
MOB1-12HN1-QC2
MOB-12HN1-QC2
MOF-18HN1-QC2
MOF1-21HN1-QB8W
MOF3-24HN1-QB8W
11
4. Refrigerant Cycle Diagram
For heat pump models:
INDOOR
OUTDOOR
CHECK VALVE
(Heating Model only)
LIQUID SIDE
2-WAY VALVE
CAPILIARY TUBE
HEAT
EXCHANGE
(EVAPORATOR)
HEAT
EXCHANGE
(CONDENSER)
GAS SIDE
REVERSING VALVE
(Heating Model only)
3-WAY VALVE
ACCUMULATOR
COOLING
COMPRESSOR
12
HEATING
5. Wiring Diagram
5.1 Indoor Units
MSX-07HRN1-QC2
MSX-09HRN1-QC2
MSX-12HRN1-QC2
13
MSX-18HRN1-QC2
MSX-21HRN1-QB8W, MSX-24HRN1-QB8W
14
5.2 Outdoor Units
MOA-07HN1-QC2
15
MOA1-09HN1-QC2 MOA-09HN1-QC2 MOB1-12HN1-QC2 MOB-12HN1-QC2
16
MOF-18HN1-QC2
17
MOF1-21HN1-QB8W
MOF3-24HN1-QB8W
18
6. Installation details
6.1 Wrench torque sheet for installation
Outside diameter
Torque
Additional tightening torque
mm
inch
N.cm
N.cm
Ф6.35
1/4
1500(153kgf.cm)
1600(163kgf.cm)
Ф9.52
3/8
2500(255kgf.cm)
2600(265kgf.cm)
Ф12.7
1/2
3500(357kgf.cm)
3600(367kgf.cm)
Ф16
5/8
4500(459kgf.cm)
4700(479kgf.cm)
Ф19
3/4
6500(663kgf.cm)
6700(683kgf.cm)
6.2 Connecting the cables
The power cord of connect should be selected according to the following specifications sheet.
Rated current of appliance
Nominal cross-sectional area (mm²)
>3 and ≤6
0.75
>6 and ≤10
1.0
>10 and ≤16
1.5
>16 and ≤25
2.5
The cable size and the current of the fuse or switch are determined by the maximum current indicated
on the nameplate which located on the side panel of the unit. Please refer to the nameplate before
selecting the cable, fuse and switch.
19
6.3 Pipe length and the elevation
The pipe length and refrigerant amount:
Additional amount of
Model
Connective pipe length
Air purging
refrigerant
All
Less than 5m
Use vacuum pump
------------------
More than 5m
Use vacuum pump
(Pipe length – 5) × 20g/m
More than 5m
Use vacuum pump
(Pipe length – 5) × 40g/m
MSX-07HRN1-QC2
MSX-09HRN1-QC2
MSX-12HRN1-QC2
MSX-18HRN1-QC2
MSX-21HRN1-QB8W
MSX-24HRN1-QB8W
Model
Standard
Max.
Max.
length
Elevation
Length
(m)
B (m)
A (m)
5
8
20
5
10
25
MSX-07HRN1-QC2
MSX-09HRN1-QC2
MSX-12HRN1-QC2
MSX-18HRN1-QC2
MSX-21HRN1-QB8W
MSX-24HRN1-QB8W
20
Caution:
The capacity test is based on the standard length and the maximum permissive length is based on the
system reliability.
The oil trap should be installed per 5-7 meters.
21
6.4 Installation for the first time
Air and moisture in the refrigerant system have undesirable effects as below:
●
●
●
●
●
Pressure in the system rises.
Operating current rises.
Cooling or heating efficiency drops.
Moisture in the refrigerant circuit may freeze and block capillary tubing.
Water may lead to corrosion of parts in the refrigerant system.
Therefore, the indoor units and the pipes between indoor and outdoor units must be leak tested
and evacuated to remove gas and moisture from the system.
Gas leak check (Soap water method):
Apply soap water or a liquid neutral detergent on the indoor unit connections or outdoor unit
connections by a soft brush to check for leakage of the connecting points of the piping. If bubbles
come out, the pipes have leakage.
1. Air purging with vacuum pump
(Indoor unit)
(Outdoor unit)
(Liquid side)
Two-way valve
Close
(Gas side)
Three-way valve
Manifold valve
Compound meter
Pressure
gauge
20Pa
Lo
Handle Lo
Charge hose
Close
Hi
Handle Hi
Charge hose
Vacuum
pump
Vacuum
pump
1) Completely tighten the flare nuts of the indoor and outdoor units, confirm that both the 2-way and
3-way valves are set to the closed position.
2) Connect the charge hose with the push pin of handle lo to the 3-way valves gas service port.
3) Connect the charge hose of handle hi connection to the vacuum pump.
4) Fully open the handle Lo of the manifold valve.
5) Operate the vacuum pump to evacuate.
6) Make evacuation for 30 minutes and check whether the compound meter indicates -0.1Mpa. If
the meter does not indicate -0.1Mpa after pumping 30 minutes, it should be pumped 20 minutes more. If
22
the pressure can’t achieve -0.1Mpa after pumping 50 minutes, please check if there are some leakage
points.
Fully close the handle Lo valve of the manifold valve and stop the operation of the vacuum pump.
Confirm that the gauge needle does not move (approximately 5 minutes after turning off the vacuum
pump).
7) Turn the flare nut of the 3-way valves about 45° counterclockwise for 6 or 7seconds after the gas
coming out, then tighten the flare nut again. Make sure the pressure display in the pressure indicator is
a little higher than the atmosphere pressure. Then remove the charge hose from the 3 way valve.
8) Fully open the 2 way valve and 3 way valve and securely tighten the cap of the 3 way valve.
2. Air purging by refrigerant
Procedure:
1). Confirm that both the 2-way and 3-way valves are set to the closed position.
2). Connect the charge set and a charging cylinder to the service port of the 3-way valve.
3). Air purging
Open the valves on the charging cylinder and the charge set. Purge the air by loosening the flare nut on
the 2-way valve approximately 45’ for 3 seconds then closing it for 1 minute; repeat 3 times.
After purging the air, use a torque wrench to tighten the flare nut on the 2-way valve.
4). Check the gas leakage
Check the flare connections for gas leakage.
5). Discharge the refrigerant
Close the valve on the charging cylinder and discharge the refrigerant by loosening the flare nut on the
23
2-way valve approximately 45’ until the gauge indicates 0.3 to 0.5 Mpa.
6). Disconnect the charge set and the charging cylinder, and set the 2-way and 3-way valves to the open
position.
Be sure to use a hexagonal wrench to operate the valve stems.
7). Mount the valve stems nuts and the service port cap
Be sure to use a torque wrench to tighten the service port cap to a torque 18N·m.
Be sure to check the gas leakage.
3. Adding the refrigerant if the pipe length >5m
Electronic scale
Procedure:
1). Connect the charge hose to the charging cylinder, open the 2-way valve and the 3-way valve.
Connect the charge hose which you disconnected from the vacuum pump to the valve at the bottom of
the cylinder. If the refrigerant is R410A, make the cylinder bottom up to ensure the liquid charge.
2). Purge the air from the charge hose
Open the valve at the bottom of the cylinder and press the check valve on the charge set to purge the
air (be careful of the liquid refrigerant).
3) Put the charging cylinder onto the electronic scale and record the weight.
4) Operate the air conditioner at the cooling mode.
5) Open the valves (Low side) on the charge set and charge the system with liquid refrigerant.
6).When the electronic scale displays the proper weight (refer to the table), disconnect the charge hose
24
from the 3-way valve’s service port immediately and turn off the air conditioner before disconnecting the
hose.
7). Mount the valve stem caps and the service port
Use torque wrench to tighten the service port cap to a torque of 18N.m.
Be sure to check for gas leakage.
6.5 Adding the refrigerant after running the system for many years
Electronic scale
Procedure:
1). Connect the charge hose to the 3-way service port, open the 2-way valve and the 3-way valve.
Connect the charge hose to the valve at the bottom of the cylinder. If the refrigerant is R410A, make
the cylinder bottom up to ensure liquid charge.
2). Purge the air from the charge hose
Open the valve at the bottom of the cylinder and press the check valve on the charge set to purge the
air (be careful of the liquid refrigerant).
3) Put the charging cylinder onto the electronic scale and record the weight.
4) Operate the air conditioner at the cooling mode.
5) Open the valves (Low side) on the charge set and charge the system with liquid refrigerant.
6).When the electronic scale displays the proper weight (refer to the gauge and the pressure of the low
25
side), disconnect the charge hose from the 3-way valve’s service port immediately and turn off the air
conditioner before disconnecting the hose.
7). Mount the valve stem caps and the service port
Use torque wrench to tighten the service port cap to a torque of 18N.m.
Be sure to check for gas leakage.
6.6 Re-installation while the indoor unit need to be repaired
1. Collecting the refrigerant into the outdoor unit
Procedure
1). Confirm that both the 2-way and 3-way valves are set to the opened position.
Remove the valve stem caps and confirm that the valve stems are in the opened position.
Be sure to use a hexagonal wrench to operate the valve stems.
2). Connect the charge hose with the push pin of handle lo to the 3-way valves gas service port.
3). Air purging of the charge hose
Open the handle Lo valve of the manifold valve slightly to purge air from the charge hose for 5 seconds
and then close it quickly.
4). Set the 2-way valve to the close position.
5). Operate the air conditioner at the cooling cycle and stop it when the gauge indicates 0.1MPa.
26
6). Set the 3-way valve to the closed position immediately.
Do this quickly so that the gauge ends up indicating 0.3 to 0.5Mpa.
Disconnect the charge set, and tighten the 2-way and 3-way valve’s stem nuts.
Use a torque wrench to tighten the 3-way valves service port cap to a torque of 1.8 kgf.m.
Be sure to check for gas leakage.
2. Air purging by the refrigerant
Procedure:
1). Confirm that both the 2-way and 3-way valves are set to the closed position.
2). Connect the charge set and a charging cylinder to the service port of the 3-way valve.
Leave the valve on the charging cylinder closed.
3). Air purging
Open the valves on the charging cylinder and the charge set. Purge the air by loosening the flare nut on
the 2-way valve approximately 45’ for 3 seconds then closing it for 1 minute; repeat 3 times.
After purging the air, use a torque wrench to tighten the flare nut on the 2-way valve.
4). Check the gas leakage
Check the flare connections for gas leakage.
5). Discharge the refrigerant
Close the valve on the charging cylinder and discharge the refrigerant by loosening the flare nut on the
27
2-way valve approximately 45’ until the gauge indicates 0.3 to 0.5 Mpa.
6). Disconnect the charge set and the charging cylinder, and set the 2-way and 3-way valves to the open
position.
Be sure to use a hexagonal wrench to operate the valve stems.
7). Mount the valve stems nuts and the service port cap.
Be sure to use a torque wrench to tighten the service port cap to a torque 18N.m.
Be sure to check the gas leakage.
6.7 Re-installation while the outdoor unit need to be repaired
1. Evacuation for the whole system
Procedure:
1). Confirm that both the 2-way and 3-way valves are set to the opened position.
2). Connect the vacuum pump to 3-way valve’s service port.
3). Evacuation for approximately one hour
Confirm that the compound meter indicates -0.1Mpa.
4). Close the valve (Low side) on the charge set, turn off the vacuum pump, and confirm that the gauge
needle does not move (approximately 5 minutes after turning off the vacuum pump).
5). Disconnect the charge hose from the vacuum pump.
28
2. Refrigerant charging
Electronic scale
Procedure:
1). Connect the charge hose to the charging cylinder, open the 2-way valve and the 3-way valve.
Connect the charge hose which you disconnected from the vacuum pump to the valve at the bottom of
the cylinder. If the refrigerant is R410A, make the cylinder bottom up to ensure liquid charge.
2). Purge the air from the charge hose
Open the valve at the bottom of the cylinder and press the check valve on the charge set to purge the
air (be careful of the liquid refrigerant).
3) Put the charging cylinder onto the electronic scale and record the weight.
4). Open the valves (Low side) on the charge set and charge the system with liquid refrigerant.
If the system cannot be charge with the specified amount of refrigerant, or can be charged with a little at
a time (approximately 150g each time) , operating the air conditioner in the cooling cycle; however, one
time is not sufficient, wait approximately 1 minute and then repeat the procedure.
5).When the electronic scale displays the proper weight, disconnect the charge hose from the 3-way
valve’s service port immediately.
If the system has been charged with liquid refrigerant while operating the air conditioner, turn off the air
conditioner before disconnecting the hose.
6). Mounted the valve stem caps and the service port
29
Use torque wrench to tighten the service port cap to a torque of 18N.m.
Be sure to check for gas leakage.
30
7. Operation characteristics
CAUTION:
1. If air conditioner is used outside of the above conditions, certain safety protection features may
come into operation and cause the unit to function abnormally.
2. Room relative humidity less than 80%. If the air conditioner operates in excess of this figure, the
surface of the air conditioner may attract condensation. Please set the vertical air flow louver to its
maximum angle (vertically to the floor), and set HIGH fan mode.
3. Optimum performance will be achieved within this operating temperature.
31
8. Electronic function
8.1 Abbreviation
T1: Indoor ambient temperature
T2: Coil temperature of indoor heat exchanger
T3: Coil temperature of outdoor heat exchanger
T4: Outdoor ambient temperature
T5: Compressor discharge temperature
8.2 Display function
Icon explanation on indoor display board.
ON/OFF indicator
This indicator illuminates when the air conditioner is in operation.
PRE.-DEF. Indicator (For Cooling & Heating models only)
This indicator illuminates when the air conditioner starts defrosting automatically or when
the warm air control feature is activated in heating mode.
Auto Mode
This indicator illuminates when the air conditioner is in Auto Mode.
Turbo indicator
This indicator illuminates when the air conditioner is in turbo operation.
TEMPERATURE indicator
Usually it displays the temperature settings.
TIMER indicator
This indicator illuminates when TIMER is set ON/OFF.
FAN SPEED indicator
This indicator illuminates when change the fan speed.
32
Ionizer ( Plasma ) function indicator
This indicator illuminates when Ionizer ( Plasma ) function is on.
33
8.3 Main Protection
8.3.1 Time Delay at restart for compressor.
8.3.2 Fan Speed is out of control. (only for MSX-07HRN1-QC2, MSX-09HRN1-QC2,
MSX-12HRN1-QC2, MSX-18HRN1-QC2 models)
----When Indoor Fan Speed keeps too low or too high for certain time, the unit will stop and the LED
will display the failure
8.3.3 Current protection
A
I3SEC
B
I5MIN
C
IFAN
IRESTORE
Resume
A zone : The current exceeds I3SEC for 5 seconds, the compressor and outdoor fan will shut off.
B zone: The current exceeds I5min for 5 minutes, the compressor and outdoor fan will shut off.
C zone: The current exceeds IFAN, the outdoor fan will shut off if AC is in heating mode. If AC is in
cooling mode, the indoor fan will run at low speed.
I3SEC =7.0A, I5min =6.0A, IFAN =5.0A, IRESTORE=6.5A for MSX-07HRN1-QC2 model.
I3SEC =10.0A, I5min =7.5A, IFAN =6.0A, IRESTORE=5.0A for MSX-09HRN1-QC2 model.
I3SEC =12.0A, I5min =8.5A, IFAN =7.5A, IRESTORE=6.5A for MSX-12HRN1-QC2 model.
I3SEC =19.5A, I5min =17.0A, IFAN =15.0A, IRESTORE=13.0A for MSX-18HRN1-QC2 model.
I3SEC =22.0A, I5min =20.0A, IFAN =16.0A, IRESTORE=14.0A for MSX-21HRN1-QB8W model.
I3SEC =26.0A, I5min =24.0A, IFAN =19.0A, IRESTORE=17.0A for MSX-24HRN1-QB8W model.
8.3.4 Zero crossing detection error protection (only for MSX-07HRN1-QC2, MSX-09HRN1-QC2,
MSX-12HRN1-QC2, MSX-18HRN1-QC2 models)
If AC can not detect zero crossing signal for 4 minutes or the zero crossing signal time interval is not
correct, the unit will stop and the LED will display the failure. The correct zero crossing signal time
interval should be between 6-13ms.
34
8.3.5 Indoor / outdoor units communication protection(only for MSX-21HRN1-QB8W,
MSX-24HRN1-QB8W model)
If the indoor units can not receive the feedback signal from the outdoor units for 2 minutes, the AC will
stop and display the failure.
35
8.4 Operation Modes and Functions
8.4.1 Fan mode.
(1) Outdoor fan and compressor stop.
(2) Temperature setting function is disabled, and no setting temperature is displayed.
(3) Indoor fan can be set to high/med/low/auto.
(4) The louver operates same as in cooling mode.
(5) Auto fan:
8.4.2 Cooling Mode
8.4.2.1 Compressor running rules:
Once the compressor starts up, it will follow the below rules:
When indoor room temp.T1 is lower than Tn, the compressor and outdoor fan will shut off. When T1 is
higher than Tm, the compressor and outdoor fan will start up.
Tm=Ts ,Tn=Ts-2 for MSX-07HRN1-QC2, MSX-09HRN1-QC2, MSX-12HRN1-QC2,
MSX-18HRN1-QC2 models.
Tm=Ts+1, Tn=Ts for MSX-21HRN1-QB8W, MSX-24HRN1-QB8W model.
8.4.2.2 Outdoor fan running rules:
The On-off outdoor units have single fan speed. The outdoor fan will run following the compressor
except when AC is in evaporator high temp. protection in heating mode ,condenser high temp.
36
protection in cooling mode, defrosting mode and the current protection.
8.4.2.3 Indoor fan running rules
In cooling mode, indoor fan runs all the time and the speed can be selected as high, medium, low and
auto.
The auto fan:
8.4.2.4 Evaporator low temperature T2 protection.
When the evaporator coil temp.T2 keeps lower than TE5 for 5 minutes, the compressor and outdoor
fan will shut off.
When T2 is higher than TE6, the compressor and outdoor fan will restart up.
While TE5=4℃, TE6=10℃for MSX-07HRN1-QC2, MSX-09HRN1-QC2(2T0032300007
2T0032300007), MSX-12HRN1-QC2(2T0032500006),
TE5=2℃, TE6=7℃ for MSX-09HRN1-QC2(2T0032300534), MSX-12HRN1-QC2(2T0032500185),
MSX-18HRN1-QC2 models;
TE5=2℃, TE6=12℃ for MSX-21HRN1-QB8W, MSX-24HRN1-QB8W models.
37
8.4.2.5
Condenser
high
temperature
T3
protection.(only
for
MSX-21HRN1-QB8W,
MSX-24HRN1-QB8W model)
T3
Off
TE10
TE11
On
When T3≥TE10, the compressor will shut off. When T3<TE11,the compressor will restart.
TE10=65℃, TE11=55℃.
8.4.3 Heating Mode
8.4.3.1 Compressor running rules:
Every time, the compressors start up, they will keep running for △t minutes (protections are active)
and then follow the below rules. (While △t=7.)
When indoor room temp.T1 is higher than Tj, the compressor and outdoor fan will shut off. When T1 is
lower than Tk, the compressor and outdoor fan will start up.
Tj=Ts+6
Tk=Ts+4. for MSX-07HRN1-QC2, MSX-09HRN1-QC2, MSX-12HRN1-QC2, MSX-18HRN1-QC2
models.
Tj=Ts+3
Tk=Ts+2.for MSX-21HRN1-QB8W, MSX-24HRN1-QB8W models.
8.4.3.2 Outdoor fan running rules:
The outdoor units have single fan speed. The outdoor fan will run following the compressor except
when AC is in evaporator high temp. protection in heating mode , condenser high temp. protection in
38
cooling mode ,defrosting mode and the current protection.
8.4.3.3 Indoor fan running rules:
When the compressor is off because off the room temperature rising or the protection, the indoor fan
will run at breeze.
When the compressor is on, the indoor fan can be set to high/med/low/auto. And the anti-cold wind
function has the priority.
Anti-cold wind function:
When evaporator coil temp.T2 is getting higher,
T2>TE2, the indoor fan will run at setting speed.
TE1<T2<TE2, the indoor fan will run at low speed.
When T2 is getting lower,
TE4<T2<TE3,the indoor fan will run at low speed.
T2<TE4, the indoor fan will shut off.
While TE1=28℃,TE2=38℃,TE3=30℃,TE4=20℃ for MSX-07HRN1-QC2, MSX-09HRN1-QC2
models.
TE1=31℃,TE2=36℃,TE3=30℃,TE4=20℃ for MSX-12HRN1-QC2 model(2T0032500185)
TE1=31℃,TE2=36℃,TE3=30℃,TE4=22℃ for MSX-12HRN1-QC2 model(2T0032500006)
TE1=34℃,TE2=37℃,TE3=30℃,TE4=20℃ for MSX-18HRN1-QC2 model.
TE1=25℃,TE2=32℃,TE3=30℃,TE4=20℃ for MSX-21HRN1-QB8W, MSX-24HRN1-QB8W models.
Auto fan action:
39
When T1-Ts>2℃,the indoor fan will run at low speed.
When T1-Ts≤0℃, the indoor fan will run at medium speed.
8.4.3.4 Defrosting mode:
For MSX-07HRN1-QC2,MSX-09HRN1-QC2, MSX-12HRN1-QC2, MSX-18HRN1-QC2 models:
l
Condition of defrosting:
AC will enter defrosting mode if any of the following items ①&② is satisfied:
①
AC meets A+B1 or A+B2.
A: The cumulative compressor running time is over 42 minutes.
B1: The cumulative compressor running time is between 42~120 minutes. Meanwhile the T2-T1 meet
the below table.
℃
T2-T1
High speed
<THDEFROST
Medium speed
<TMDEFROST
Low speed
<TLDEFROST
Breeze/off
No need to compare the T2 and T1
B2: The cumulative compressor running time is over 120 minutes. Meanwhile the T2-T1 meet the
below table.
℃
②
T2-T1
High speed
<THDEFROST +2
Medium speed
<TMDEFROST +2
Low speed
<TLDEFROST +2
Breeze/off
No need to compare the T2 and T1
After the last defrosting, the time that the outdoor fan is off but the compressor is on in high T2
protection cumulates up to 90 minutes.
While THDEFROST =14℃, TMDEFROST =16℃, TLDEFROST =17℃ for MSX-07HRN1-QC2 model.
THDEFROST =15℃, TMDEFROST =17℃, TLDEFROST =19℃ for MSX-09HRN1-QC2 model.
THDEFROST =14℃, TMDEFROST =15℃, TLDEFROST =16℃ for MSX-12HRN1-QC2 model.
THDEFROST =17℃, TMDEFROST =18℃, TLDEFROST =19℃ for MSX-18HRN1-QC2 model.
l
Condition of ending defrosting:
If any one of the following items is satisfied, the defrosting will terminate and the machine will turn to
normal heating mode.
40
(1) The defrosting time is reached to the setting value.
(2) The compressor current reaches or exceeds IDEFROST for 7 seconds.
IDEFROST =3.5A for MSX-07HRN1-QC2 model, IDEFROST=4.5A for MSX-09HRN1-QC2 model,
IDEFROST =5.0A for MSX-12HRN1-QC2 model. IDEFROST=8.5A for MSX-18HRN1-QC2 model.
About the setting defrosting time:
condition
runtime(minute)
Defrosting time(minute)
Case 1
①A、B1
runtime≤60
DT1
Case 2
①A、B1
60<runtime≤80
DT1+1
Case 3
①A、B1
80<runtime≤95
DT1+2
Case 4
①A、B1
95<runtime≤110
DT1+3
Case 5
①A、B1
110<runtime≤120
DT1+4
Case 6
①A、B2
DT1+5
Case 7
②
DT1+5
Note:
Ø
From case1 to case 5, If case B happens before case A and lasts till case A happens, the setting
defrosting time will be 10 minutes.
Ø
If AC enter defrosting mode continuously three times from case 1 to case 5, the fourth defrosting time will
be DT1 +5 minutes
Ø
At the beginning 6.5 minutes of compressor running, AC will not enter the defrosting mode
l
Defrosting action:
For MSX-21HRN1-QB8W,MSX-24HRN1-QB8W model:
l
Condition of defrosting:
41
AC will enter defrosting mode if any of the following items is satisfied.
(1) When T3<TC1℃, if the compressor keeps running over 45 minutes and T3<TC3℃ for 3
minutes. While TC1= 0℃, TC3=-3℃.
(2) After the last defrosting, the time that the outdoor fan is off but the compressor is on in high T2
protection cumulates up to 90 minutes.
l
Condition of ending defrosting:
If any one of the following items is satisfied, the defrosting will terminate and the machine will turn to
normal heating mode.
(1) T3 rises to be higher than TC2. TC2= 20℃.
(2) The machine has run for 10 minutes in defrosting.
l
Defrosting action:
8.4.3.5 High evaporator coil temp.T2 protection:
For MSX-07HRN1-QC2 model, MSX-09HRN1-QC2, MSX-12HRN1-QC2, MSX-18HRN1-QC2
models:
While TE7=63℃,TE8=53℃,TE9=51℃ for MSX-07HRN1-QC2 model
42
TE7=63℃,TE8=56℃,TE9=52℃ for MSX-09HRN1-QC2 model,
TE7=63℃,TE8=53℃,TE9=52℃ for MSX-12HRN1-QC2 model.
TE7=63℃,TE8=53℃,TE9=50℃ for MSX-18HRN1-QC2 model.
For MSX-21HRN1-QB8W, MSX-24HRN1-QB8W models:
While TE7=63℃,TE8=54℃,TE9=50℃,TE15=53℃.
8.4.4 Auto-mode
The machine will choose cooling, heating or fan-only mode according to ΔT (ΔT =T1-Ts).
For MSX-07HRN1-QC2, MSX-09HRN1-QC2, MSX-12HRN1-QC2, MSX-18HRN1-QC2 models:
ΔT=T1-Ts
Running mode
ΔT>2℃
Cooling
-3≤ΔT≤2℃
Fan-only
ΔT<-3℃
Heating(for cooling only models, they will
run at fan-only mode)
For MSX-21HRN1-QB8W, MSX-24HRN1-QB8W models:
ΔT=T1-Ts
Running mode
ΔT>2℃
Cooling
-1<ΔT≤2℃
Fan-only
ΔT≤-1℃
Heating(for cooling only models ,they will
run at fan-only mode)
AC will run in auto mode in the below cases:
(1) Press the forced auto button.
(2) If AC is off, it will run in auto mode when timer on function is active.
(3) After setting the mode, AC will run in auto mode if the compressor keeps not running for 20
(15 minutes for MSX-21HRN1-QB8W,MSX-24HRN1-QB8W models).
43
8.4.5 Drying mode
For MSX-07HRN1-QC2, MSX-09HRN1-QC2, MSX-12HRN1-QC2, MSX-18HRN1-QC2 models:
8.4.5.1 The indoor fan will run following the compressor. If the compressor is on ,the indoor fan will run
at low speed. If the compressor is off, the indoor fan will run at breeze.
Running rules:
No
Condition
Indoor fan
Compressor and outdoor fan
1
T1 ≥ TS+2
Low
Breeze
ON
OFF
6 minutes
4 minutes
2
TS ≤T1<TS+2
Low
Breeze
ON
OFF
5 minutes
5 minutes
3
T1 < TS
Low
Breeze
ON
OFF
4 minutes
6 minutes
8.4.5.2 In drying mode, if room temperature is lower than 10℃, the indoor fan will run at breeze while
the compressor and outdoor fan will stop and not resume until room temperature exceeds 13℃.
8.4.5.3 System protection is active in this mode.
For MSX-21HRN1-QB8W, MSX-24HRN1-QB8W models:
8.4.5.4 The indoor fan will keep running at low speed.
8.4.5.5 The outdoor fan, compressor and all the protections are the same with cooling mode.
8.4.6 Forced operation function
Press the touch button continually, the AC will run as below sequence:
Forced auto→ Forced cooling →Off
Forced cooling mode:
The compressor and outdoor fan keep running and the indoor fan runs at low speed. After running for
30 minutes, AC will turn to auto mode with 24℃ setting temperature.
Forced auto mode:
The action of forced auto mode is the same as normal auto mode with 24℃ setting temperature.
l
When AC receives signals, such as switch on, switch off, timer on, timer off, mode setting ,fan
speed setting ,sleeping mode setting ,follow me setting, it will quit the forced operation.
44
l
The forced operation function can not be memorized if power off.
8.4.7 Timer function
8.4.7.1 Timing range is 24 hours.
8.4.7.2 Timer on. The machine will turn on automatically when reaching the setting time.
8.4.7.3 Timer off. The machine will turn off automatically when reaching the setting time.
8.4.7.4 Timer on/off. The machine will turn on automatically when reaching the setting “on” time, and
then turn off automatically when reaching the setting “off” time.
8.4.7.5 Timer off/on. The machine will turn off automatically when reaching the setting “off” time, and
then turn on automatically when reaching the setting “on” time.
8.4.7.6 The timer function will not change the AC current operation mode. Suppose users set the
“timer off” function and AC is off now, the AC will keep the current running mode and then turn off when
reaching the setting time.
8.4.7.7 The setting time is relative time.
8.4.8 Sleep function mode
8.4.8.1 Operation time in sleep mode is 7 hours. After 7 hours, the AC quits this mode and turns off.
8.4.8.2. Operation process in sleep mode is as follow:
After pressing ECONOMIC or SLEEP button on controller, the machine will turn into sleep mode.
When cooling, the setting temperature rises 1℃(be lower than 30℃) every one hour, 2 hours later the
setting temperature stops rising and indoor fan is fixed as low speed.
When heating, the setting temperature decreases 1℃(be higher than 17℃) every one hour, 2 hours
later the setting temperature stops rising and indoor fan is fixed as low speed.(Anti-cold wind function
has the priority)
8.4.8.3 Timer setting is available.
8.4.8.4 When user uses timer off function in sleep mode(or sleep function in timer off mode), if the
timing is less than 7 hours, sleep function will be cancelled when reaching the setting time. If the timing
is more than 7 hours, the machine will not stop until reaches the setting time in sleep mode.
8.4.9 Auto-Restart function
The indoor unit is equipped with auto-restart function, which is carried out through an auto-restart
module. In case of a sudden power failure, the module memorizes the setting conditions before the
power failure. The unit will resume the previous operation setting (not including Swing function)
45
automatically after 3 minutes when power returns.
If the memorization condition is forced cooling mode, the unit will run in cooling mode for 30 minutes
and then turn to auto mode as 24℃ setting temp.
46
9. Troubleshooting
9.1 Indoor unit error display
For MSX-07HRN1-QC2, MSX-09HRN1-QC2, MSX-12HRN1-QC2, MSX-18HRN1-QC2 models:
LED
Failure
E1
EEPROM error
E2
Zero crossing detection error
E3
Indoor fan speed has been out of control
E4
Over current protection occurs 4 times.
E5
The T1 sensor is open circuit or short circuit
E6
The T2 sensor is open circuit or short circuit
For MSX-21HRN1-QB8W, MSX-24HRN1-QB8W models:
LED
Failure
E1
EEPROM error
E4
Over current protection occurs 4 times.
E5
The T1 sensor is open circuit or short circuit
E6
The T2 sensor is open circuit or short circuit
E7
The T3 sensor is open circuit or short circuit
E9
Indoor / outdoor units communication error
47
9.2 Diagnosis and Solution
9.2.1 Indoor fan speed out of control diagnosis and solution
Shut off the power supply and turn
on it 5s later
The unit does not work
normally
Turn off the unit, rotate the cross
fan. Does it rotate freely?
Disassemble the connection between
the fan and the motor, check if the
bearing is normal. If not, change the
bearing. If yes, follow the below step.
No
Yes
Is the fan motor connector and
connection good?
Yes
Replace the outdoor fan motor
The problem is not
resolved.
Replace the outdoor PCB
48
9.2.2 Open or short circuit of temperature sensor diagnosis and solution.
Check the connections between
the sensors and the PCB. Are the
connections good?
Yes
Yes
Replace the sensor and check if
the errors happen again?
Replace the PCB
9.2.3 Over current protection occurs 4 times.
Check if the voltage of the power supply is too low
Yes
Repair the power supply
No
No
Check if the operation condition is
normal, especially the outdoor unit?
Correct the operation condition
Yes
Disconnect with the power and
replace the main PCB
Yes
Turn on the units and check if the
problem remains
Yes
Check if the
compressor
is normal
No
Replace the
compressor
Yes
Replace the
capillary
Yes
Check if the
capillary is
blocked
No
There is some air
mixed inside the
refrigerant system
49
Evacuate the
refrigerant
system and
recharge gas
9.2.4 EEPROM parameter error diagnosis and solution
Shut off the power supply and turn on it 5s later
The problem comes out again
Is the EEPROM chip plugged in indoor PCB well?
No
Replace the main PCB of indoor unit
9.2.5 Zero crossing detection error
When such failure occurs, the main control board must have fault.
50
Correct the connection
9.2.6
Indoor / outdoor units communication error diagnosis and solution
Power off, then power on the A/C by
the breaker.(reconnect the power
wire). Is the error extinguished?
No
Check the wiring on the outdoor
terminal
and indoor
terminal
following the wiring diagram. Is all
the connecting correctly?
Yes
No
-24V<Vs<+24V?
(Vs is the voltage between S and N
of outdoor unit.)
Yes
Is the wiring to the indoor PCB
connecting correctly?
Is the wiring to the outdoor PCB
connecting correctly?
Yes
Yes
Change the outdoor PCB
Change the indoor PCB
Power on. Is the error extinguished
after 3 minutes?
Power on. Is the error extinguished
after 3 minutes?
No
No
Change the indoor PCB
Change the outdoor PCB
51
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement