Samsung CLX-3160N Service manual

DIGITAL COLOR LASER MFP

CLX-3160 Series

CLX-3160FN/

XAA

Basic Model : CLX-3160FN

SERVICE Manual

DIGITAL COLOR LASER MFP The keynote of Product

1. Engine Speed :

Up to 16 ppm in A4 black (17 ppm in Letter)

Up to 4 ppm in A4 color (4 ppm in Letter)

2. Resolution :

- Optical, 600 x 600 dpi

- Support, MAX: 2400 x 600 dpi class, 1200 x 600 dpi

(default), 600 x 600 dpi (Color & B&W)

3. MPU : Samsung CHORUSm 300MHz

4. Memory :

- Std.: 128 MB, Max.: 128 MB (Memory not Expansion)

5. Default Driver: SPL-C (Samsung Printer Language Color)

6. USB: USB 2.0, USB host (Scan to USB, Direct print)

7. Network : Ethernet 10/100 Base TX

8. Consumable :

- 6 (C/M/Y/K toner, Imaging Unit, Waste toner box)

- K toner : CLX-K3160A

- C toner : CLX-C3160A

- M toner : CLX-M3160A

- Y toner : CLX-Y3160A

- Imaging unit : CLP-R300A (common with CLP-300)

- Waste toner box : CLP-W300A (common with CLP-300)

- CMY Rainbow kit : CLX-P3160A

9. SET Life Cycle : 200,000 image

Contents

1.Precautions

1.1 Safety Warning

1.2 Caution for safety

1.3 ESD Precautions

1.4 Super Capacitor or Lithium Battery Precautions

2.Product Specification

2.1 Product Overview

2.2 Product General Specifications

2.3 Model Comparison Table

3.System Overview

3.1 System Structure

3.2 Main PBA Description

3.3 CRUM

3.4 General Description

4. S/W Structure and Descriptions

4.1 Overview

4.2 Architecture

4.3 Data and Control Flow

4.4 Alarm Shortage

4.5 Error status

4.6 CRUM Overview

4.7 FW Upgrade

4.8 Initailize Flow

2-1

2-2

2-14

3-1

3-14

3-30

3-32

1-1

1-2

1-5

1-5

4-4

4-5

4-5

4-6

4-1

4-1

4-2

4-4

Continued

5. Disassembly and Reassembly

5.1 General Precautions on Disassembly

5.2 Cover Upper (Left, Right)

5.3 Front Cover

5.4 OPC DEV Unit

5.5 ITB Unit

5.6 T2 Roller Unit

5.7 Rear Cover

5.8 OPE Unit

5.9 Side Cover (Left, Right)

5.10 ADF Ass'y

5.11 Platen Ass'y

5.12 Middle Cover Ass'y

5.13 Fuser Ass'y

5.14 HVPS

5.15 LIU Unit

5.16 Shield Main Lower (with Main PBA)

5.17 Main Drive Ass'y

5.18 SMPS

5.19 Regi Roller

5.20 Feed Roller

5.21 Pick Up Roller

5.22 Exit Roller Unit

5.23 LSU

5.24 MP Unit

6. Alignment and Adjustmens

6.1 Control Panel

6.2 LED Function

6.3 Jam Removal

5-7

5-9

5-10

5-12

5-17

5-19

5-21

5-22

5-1

5-2

5-3

5-4

5-5

5-6

5-6

5-23

5-24

5-25

5-26

5-28

5-29

5-32

5-34

5-34

6-1

6-3

6-4

Continued

6.4 System setup

6.5 Network setup

6.6 Sample Pattern

6.7 Periodic Defective Image

6.8 Tech Mode

6.9 Error Message

7. Troubleshooting

7.1 Procedure of Checking the Symptoms

7.2 Solving other problems

8. Exploded Views & Parts List

8.1 Main

8.2 Middle Cover

8.3 Front Cover

8.4 Right Cover

8.5 Round Cover

8.6 Rear Cover

8.7 Cover Platen

8.8 Platen Ass'y

8.9 OPE(CLX-3160FN)

OPE(CLX-3160N)

8.10 Scan Ass'y

8.11 ADF Ass'y

8.12 ADF Lower

8.13 ADF Motor

8.14 Frame

8.15 Main Driver

8.16 LSU Cover

8.17 ITB Unit

6-10

6-16

6-20

6-22

6-23

6-34

7-1

7-2

8-9

8-10

8-11

8-12

8-13

8-14

8-15

8-16

8-2

8-3

8-4

8-5

8-6

8-7

8-8

8-18

8-20

8-21

Continued

8.18 OPC DEVE

8.19 Fuser Ass'y

8.20 Cassette

9. Block diagram

9.1 Block Diagram

10.Connection Diagram

10.1 Connection Diagram

1 1 . Reference Information

1 1 .1 Tools for Troubleshooting

1 1 .2 Acronyms and Abbreviations

1 1 .3 Select a location for the printer

1 1 .4 A4 ISO 19752 Standard Pattern

1 1 .5 Wireless LAN

10-1

1 1 -1

1 1 -2

1 1 -4

1 1 -5

1 1 -6

8-22

8-24

8-25

10-1

9-1

1

1. Precautions

In order to prevent accidents and to prevent damage to the equipment please read the precautions listed below carefully before servicing the printer and follow them closely.

1.1 Safety Warning

(1) Only to be serviced by appropriately qualified service engineers.

High voltages and lasers inside this product are dangerous. This printer should only be serviced by a suitably trained and qualified service engineer.

Precautions

(2) Use only Samsung replacement parts

There are no user serviceable parts inside the printer. Do not make any unauthorized changes or additions to the printer, these could cause the printer to malfunction and create electric shock or fire haz-ards.

(3) Laser Safety Statement

The Printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J for

Class 1(1) laser products, and elsewhere, it is certified as a Class I laser product con-forming to the requirements of IEC 825. Class I laser products are not considered to be hazardous. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.

Warning >> Never operate or service the printer with the protective cover removed from Laser/Scanner assembly. The reflected beam, although invisible, can damage your eyes. When using this product, these basic safety pre-cautions should always be followed to reduce risk of fire, electric shock, and injury to persons.

CAUTION - INVISIBLE LASER RADIATION

WHEN THIS COVER OPEN.

DO NOT OPEN THIS COVER.

VORSICHT - UNSICHTBARE LASERSTRAHLUNG,

WENN ABDECKUNG GEÖFFNET.

NICHT DEM STRAHL AUSSETZEN.

ATTENTION - RAYONNEMENT LASER INVISIBLE EN CAS

D’OUVERTURE. EXPOSITION DANGEREUSE

AU FAISCEAU.

ATTENZIONE - RADIAZIONE LASER INVISIBILE IN CASO DI

APERTURA. EVITARE L’ESPOSIZIONE AL

FASCIO.

PRECAUCION - RADIACION LASER IVISIBLE CUANDO SE ABRE.

EVITAR EXPONERSE AL RAYO.

ADVARSEL. - USYNLIG LASERSTRÅLNING VED ÅBNING, NÅR

SIKKERHEDSBRYDERE ER UDE AF FUNKTION.

UNDGÅ UDSAETTELSE FOR STRÅLNING.

ADVARSEL. - USYNLIG LASERSTRÅLNING NÅR DEKSEL

ÅPNES. STIRR IKKE INN I STRÅLEN.

UNNGÅ EKSPONERING FOR STRÅLEN.

VARNING - OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.

VARO! - AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTIINA NÄKYMÄTTÖMÄLLE LASER-

SÄTEILYLLE ÄLÄ KATSO SÄTEESEEN.

Service Manual

1-1

Samsung Electronics

Precautions

1.2 Caution for safety

1.2.1 Toxic material

This product contains toxic materials that could cause illness if ingested.

(1) If the LCD control panel is damaged it is possible for the liquid inside to leak. This liquid is toxic. Contact with the skin should be avoided, wash any splashes from eyes or skin immediately and contact your doctor. If the liquid gets into the mouth or is swallowed see a doctor immediately.

(2) Please keep toner cartridges away from children. The toner powder contained in the toner cartridge may be harmful and if swallowed you should contact a doctor.

1.2.2 Electric Shock and Fire Safety Precautions

Failure to follow the following instructions could cause electric shock or potentially cause a fire.

(1) Use only the correct voltage, failure to do so could damage the printer and potentially cause a fire or electric shock.

(2) Use only the power cable supplied with the printer. Use of an incorrectly specified cable could cause the cable to overheat and potentially cause a fire.

(3) Do not overload the power socket, this could lead to overheating of the cables inside the wall and could lead to a fire.

(4) Do not allow water or other liquids to spill into the printer, this can cause electric shock. Do not allow paper clips, pins or other foreign objects to fall into the printer these could cause a short circuit leading to an electric shock or fire hazard..

(5) Never touch the plugs on either end of the power cable with wet hands, this can cause electric shock. When servicing the printer remove the power plug from the wall socket.

(6) Use caution when inserting or removing the power connector. The power connector must be inserted completely otherwise a poor contact could cause overheating possibly leading to a fire. When removing the power connector grip it firmly and pull.

(7) Take care of the power cable. Do not allow it to become twisted, bent sharply round corners or other wise damaged. Do not place objects on top of the power cable. If the power cable is damaged it could overheat and cause a fire or exposed cables could cause an electric shock. Replace a damaged power cable immediately, do not reuse or repair the damaged cable. Some chemicals can attack the coating on the power cable, weakening the cover or exposing cables causing fire and shock risks.

(8) Ensure that the power sockets and plugs are not cracked or broken in any way. Any such defects should be repaired immediately. Take care not to cut or damage the power cable or plugs when moving the machine.

(9) Use caution during thunder or lightening storms. Samsung recommend that this machine be disconnected from the power source when such weather conditions are expected. Do not touch the machine or the power cord if it is still connected to the wall socket in these weather conditions.

(10) Avoid damp or dusty areas, install the printer in a clean well ventilated location. Do not position the machine near a humidifier. Damp and dust build up inside the machine can lead to overheating and cause a fire.

(11) Do not position the printer in direct sunlight. This will cause the temperature inside the printer to rise possibly leading to the printer failing to work properly and in extreme conditions could lead to a fire.

(12) Do not insert any metal objects into the machine through the ventilator fan or other part of the casing, it could make contact with a high voltage conductor inside the machine and cause an electric shock.

1-2

Service Manual

Samsung Electronics

Precautions

1.2.3 Handling Precautions

The following instructions are for your own personal safety, to avoid injury and so as not to damage the printer

(1) Ensure the printer is installed on a level surface, capable of supporting its weight. Failure to do so could cause the printer to tip or fall.

(2) The printer contains many rollers, gears and fans. Take great care to ensure that you do not catch your fingers, hair or clothing in any of these rotating devices.

(3) Do not place any small metal objects, containers of water, chemicals or other liquids close to the printer which if spilled could get into the machine and cause damage or a shock or fire hazard.

(4) Do not install the machine in areas with high dust or moisture levels, beside on open window or close to a humidifier or heater. Damage could be caused to the printer in such areas.

(5) Do not place candles, burning cigarettes, etc on the printer, These could cause a fire.

1.2.4 Assembly / Disassembly Precautions

Replace parts carefully, always use Samsung parts. Take care to note the exact location of parts and also cable routing before dismantling any part of the machine. Ensure all parts and cables are replaced correctly.

Please carry out the following procedures before dismantling the printer or replacing any parts.

(1) Check the contents of the machine memory and make a note of any user settings. These will be erased if the mainboard or network card is replaced.

(2) Ensure that power is disconnected before servicing or replacing any electrical parts.

(3) Disconnect printer interface cables and power cables.

(4) Only use approved spare parts. Ensure that part number, product name, any voltage, current or temperature rating are correct.

(5) When removing or re-fitting any parts do not use excessive force, especially when fitting screws into plastic.

(6) Take care not to drop any small parts into the machine.

(7) Handling of the OPC Drum

- The OPC Drum can be irreparably damaged if it exposed to light.

Take care not to expose the OPC Drum either to direct sunlight or to fluorescent or incandescent room lighting. Exposure for as little as 5 mins can damage the surface’s photoconductive properties and will result in print quality degradation. Take extra care when servicing the printer. Remove the OPC Drum and store it in a black bag or other lightproof container. Take care when working with the covers(especially the top cover) open as light is admitted to the OPC area and can damage the OPC Drum.

- Take care not to scratch the green surface of OPC Drum Unit.

If the green surface of the Drum Cartridge is scratched or touched the print quality will be compromised.

Service Manual

1-3

Samsung Electronics

Precautions

1.2.5 Disregarding this warning may cause bodily injury

(1) Be careful with the high temperature part.

The fuser unit works at a high temperature. Use caution when working on the printer. Wait for the fuser to cool down before disassembly.

(2) Do not put finger or hair into the rotating parts.

When operating a printer, do not put hand or hair into the rotating parts (Paper feeding entrance, motor, fan, etc.). If do, you can get harm.

(3) When you move the printer.

This printer weighs 19.95kg including toner cartridge and cassette. Use safe lifting and handling techniques.

Use the lifting handles located on each side of the machine. Back injury could be caused if you do not lift carefully.

(4) Ensure the printer is installed safely.

The printer weighs 19.95Kg, ensure the printer is installed on a level surface, capable of supporting its weight.

Failure to do so could cause the printer to tip or fall possibly causing personal injury or damaging the printer.

(5) Do not install the printer on a sloping or unstable surface. After installation, double check that the printer is stable.

1-4

Service Manual

Samsung Electronics

Precautions

1.3 ESD Precautions

Certain semiconductor devices can be easily damaged by static electricity. Such components are commonly called

“Electrostatically Sensitive (ES) Devices”, or ESDs. Examples of typical ESDs are: integrated circuits, some field effect transistors, and semiconductor “chip” components.

The techniques outlined below should be followed to help reduce the incidence of component damage caused by static electricity.

Caution >>Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

1. Immediately before handling a semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, employ a commercially available wrist strap device, which should be removed for your personal safety reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ESDs, place the assembly on a conductive surface, such as aluminum or copper foil, or conductive foam, to prevent electrostatic charge buildup in the vicinity of the assembly.

3. Use only a grounded tip soldering iron to solder or desolder ESDs.

4. Use only an “anti-static” solder removal device. Some solder removal devices not classified as “anti-static” can generate electrical charges sufficient to damage ESDs.

5. Do not use Freon-propelled chemicals. When sprayed, these can generate electrical charges sufficient to damage ESDs.

6. Do not remove a replacement ESD from its protective packaging until immediately before installing it. Most replacement ESDs are packaged with all leads shorted together by conductive foam, aluminum foil, or a comparable conductive material.

7. Immediately before removing the protective shorting material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

8. Maintain continuous electrical contact between the ESD and the assembly into which it will be installed, until completely plugged or soldered into the circuit.

9. Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such as the brushing together of clothing fabric and lifting one’s foot from a carpeted floor, can generate static electricity sufficient to damage an ESD.

1.4 Super Capacitor or Lithium Battery Precautions

1. Exercise caution when replacing a super capacitor or Lithium battery. There could be a danger of explosion and subsequent operator injury and/or equipment damage if incorrectly installed.

2. Be sure to replace the battery with the same or equivalent type recommended by the manufacturer.

3. Super capacitor or Lithium batteries contain toxic substances and should not be opened, crushed, or burned for disposal.

4. Dispose of used batteries according to the manufacture’s instructions.

Service Manual

1-5

Samsung Electronics

Product Specifications

2

2. Product Specifications

Specfications are correct at the time of printing. Product specifications are subject to change without notice. See below for product specifications.

2.1 Product Overview

1) Key Feature

Speed

- 16ppm B&W, 4ppm color print / copy

Consumables

- Black toner (2K sheet)

- CMY toner (1K sheet)

Paper handling

- 1sheet Manual slot, 150 sheet Semi-cassette, 250 sheet cassette option

Interface

- USB 2.0, Ethernet 10/100 Base TX, USB host (PictBridge)

2) Concept

Small size Color laser MFP(A4 Color laser MFP)

Target user

- Small office & small business

- CLX-3160N (3in1, SPL)

- CLX-3160FN (4in1, SPL)

Black only printing function

Auto warning sheet

USB host function

- PictBridge

- Scan to USB memory, direct printing

Service Manual

2-1

Samsung Electronics

Product Specifications

2.2 Product General Specifications

2.2.1 General Print Engine

CLX-3160 Series

Engine Speed Simplex

Warmup time

FPOT (B&W)

FPOT (Color)

Resolution

Duplex

From Ready

From Idle

From Coldboot

From Ready

From Idle

From Coldboot

Optical

Support

CLX-3160N Spec.

CLX-3160FN Spec.

Up to 16 ppm in A4 black (17 ppm in Letter) Up to 16 ppm in A4 black (17 ppm in Letter)

Up to 4 ppm in A4 color (4 ppm in Letter) Up to 4 ppm in A4 color (4 ppm in Letter)

N/A

Less than 35 sec

Less than 14 sec

N/A

Less than 35 sec

Less than 14 sec

Less than 45 sec

Less than 45 sec

Less than 26 sec

Less than 57 sec

Less than 45 sec

Less than 45 sec

Less than 26 sec

Less than 57 sec

Less than 57 sec

600 x 600 dpi

Less than 57 sec

600 x 600 dpi

MAX: 2400 x 600 dpi class, 1200 x 600 dpi MAX: 2400 x 600 dpi class, 1200 x 600 dpi

(default), 600 x 600 dpi(Color & B&W) (default), 600 x 600 dpi(Color & B&W)

2.2.2 Controller & S/W

CLX-3160 Series

MPU

Memory Std.

Max.

Memory Expansion

Printer Languages

Fonts

Printer driver Supporting OS

CLX-3160N Spec.

CLX-3160FN Spec.

Samsung CHORUSm 300MHz

128 MB

128 MB

Samsung CHORUSm 300MHz

128 MB

128 MB

N/A N/A

SPL-C (Samsung Printer Language Color) SPL-C (Samsung Printer Language Color)

Windows fonts

[Windows]

- Windows 98/Me/2000/XP

- In box N/A

Windows fonts

[Windows]

- Windows 98/Me/2000/XP

- In box N/A

[Linux]

- RedHat 8.0 ~ 9.0

- Fedora Core 1~4

- Madrake 9.2 ~ 10.1

- SuSE 8.2 ~ 9.2

- (Smart panel N/A)

[Mac]

- Mac OS 10.3~10.4

- (Mac OS 9 N/A)

- (Smart panel N/A)

[Linux]

- RedHat 8.0 ~ 9.0

- Fedora Core 1~4

- Madrake 9.2 ~ 10.1

- SuSE 8.2 ~ 9.2

- (Smart panel N/A)

[Mac]

- Mac OS 10.3~10.4

- (Mac OS 9 N/A)

- (Smart panel N/A)

2-2

Service Manual

Samsung Electronics

Product Specifications

Scan driver

Application

CLX-3160 Series CLX-3160N Spec.

CLX-3160FN Spec.

Default Driver SPL-C (Samsung Printer Language Color) SPL-C (Samsung Printer Language Color)

WHQL Windows 2000/XP Windows 2000/XP

Language Localization [Windows] [Windows]

: Korean, English, French, German, Italian, : Korean, English, French, German, Italian,

Spanish, Russian, Dutch, E.Portuguese, Spanish, Russian, Dutch, E.Portuguese,

B.Portuguese, Finish, Swedish, Norwegian, B.Portuguese, Finish, Swedish, Norwegian,

Danish, S.Chinese, T.Chinese, Polish, Danish, S.Chinese, T.Chinese, Polish,

Hungarian, Czech, Turkish, Greek Hungarian, Czech, Turkish, Greek

[Mac] [Mac]

: English, French, German, Italian, Spanish, : English, French, German, Italian, Spanish,

Korea

[Linux]

: English only

Korea

[Linux]

: English only

TWAIN

WIA

Yes

Yes(Win XP only)

Yes

Yes(Win XP only)

Network Scan (Client) Yes (multi-folder) Yes (multi-folder)

PC-FAX N/A Yes(Mono Send only, Included in SmarThru4)

PSU

Status Monitor or

Virtual panel

USB only

USB / Network, Default Install

USB only

USB / Network, Default Install

Network Management Set IP, SWAS & SWS(Linux, Mac Not support Set IP, SWAS & SWS(Linux, Mac Not support

SWAS & SWS Iexplorer 5.0 or higher) SWAS & SWS Iexplorer 5.0 or higher)

SmarThru SmarThru 4 SmarThru 4

Interface

Parallel

USB

Network

Wireless

Network Interface

Protocol

User Interface

LCD

OP UI

N/A N/A

USB 2.0, USB host 1.1 (Scan to USB, Direct print) USB 2.0, USB host 1.1 (Scan to USB, Direct print)

Ethernet 10/100 Base TX

N/A

Ethernet 10/100 Base TX

N/A

TCP/IP, IPP, SNMP V2

2 line LCD (China, Korea : Graphic LCD)

OP UI Guide 2.0

TCP/IP, IPP, SNMP V2

2 line LCD (China, Korea : Graphic LCD)

OP UI Guide 2.0

Service Manual

2-3

Samsung Electronics

Product Specifications

2.2.3 Scan

Scan method

Scan Speed

Resolution

Halftone

Scan Size

Scan Depth

Compatibility

CLX-3160 Series CLX-3160N Spec.

CLX-3160FN Spec.

Linearity, Halftone

Gray

Color

Optical

Enhanced

Color CCD

15 Sec(300dpi,USB2.0,P4 3.0GHz,512M)/Ltr

20 Sec(300dpi,USB2.0,P4 3.0GHz,512M)/Ltr

600 x 1200dpi

4800dpi x 4800dpi

256levels

Max. Document Width Max.216mm(8.5inch)

Effiective Scan Width Max 208mm(8.2inch)

Color 24bits

Mono - 1bit for Linearity & Halftone

- 8Bits for Gray scale

[Windows]

- Windows 98/Me/2000/XP

[Linux]

- RedHat 8.0 ~ 9.0

- Fedora Core 1~4

- Madrake 9.2 ~ 10.1

- SuSE 8.2 ~ 9.2

Color CCD

15 Sec(300dpi,USB2.0,P4 3.0GHz,512M)/Ltr

20 Sec(300dpi,USB2.0,P4 3.0GHz,512M)/Ltr

30 Sec(300dpi,USB2.0,P4 3.0GHz,512M)/Ltr 30 Sec(300dpi,USB2.0,P4 3.0GHz,512M)/Ltr

600 x 1200dpi

4800dpi x 4800dpi

256levels

Max.216mm(8.5inch)

Max 208mm(8.2inch)

24bits

- 1bit for Linearity & Halftone

- 8Bits for Gray scale

[Windows]

- Windows 98/Me/2000/XP

[Linux]

- RedHat 8.0 ~ 9.0

- Fedora Core 1~4

- Madrake 9.2 ~ 10.1

- SuSE 8.2 ~ 9.2

2-4

Service Manual

Samsung Electronics

Product Specifications

2.2.4 Copy

CLX-3160 Series CLX-3160N Spec.

Copy Speed

FCOT (B&W)

FCOT (Color)

Zoom Range

Multi Copy

Preset

Original Type

Automatic Background Suppression

Darkness Control

Collation Copy

Special Copy ID Card Copy

Auto fit

Margin Shift

Book Copy

Auto Suppression

Covers

Transparencies

Create Booklet

N-up copy

Clone

Poster

Simplex Copy Speed @SDMC up to 16 cpm in A4 black

(17 cpm in Letter)Up to 4 cpm in A4 color

(4 cpm in Letter)

Duplex Copy Speed N/A

From Ready Less than 18 sec

From Idle Less than 50 sec

From Coldboot

From Ready

From Idle

From Coldboot

Less than 50 sec

Less than 36 sec

Less than 75 sec

Less than 75 sec

Text

Text/Photo

Photo

25% to 400% for Platen

25% to 100% for ADF

1~99

[Original(100%)]

[A4 A5(71%)]

[LGL LTR(78%)]

[LGL A4(83%)]

[A4 LTR(94%)]

[EXE LTR(104%)]

[A5 A4(141%)]

25%, 50%, 150%, 200%, 400%

[Custom: 25-400%)]

Scan: 600x300dpi , Printing : 600x600dpi

Scan: 600x300dpi , Printing : 600x600dpi

Platen) Scan : 600x600dpi,

Printing : 1200x1200dpi

ADF) Scan : 600x300dpi,

Printing : 600x600dpi

Yes(Mono Only)

3 level

Yes(ADF Only), flushing if Memory full

Yes(Platen Only)

Yes(Platen Only)

No

No

No

No

No

No

2-up, 4-up (ADF only)

Yes (Platen Only)

Yes(Platen Only, x9 Only)

CLX-3160FN Spec.

@SDMC up to 16 cpm in A4 black

(17 cpm in Letter)Up to 4 cpm in A4 color

(4 cpm in Letter)

N/A

Less than 18 sec

Less than 50 sec

Less than 50 sec

Less than 36 sec

Less than 75 sec

Less than 75 sec

25% to 400% for Platen

25% to 100% for ADF

1~99

[Original(100%)]

[A4 A5(71%)]

[LGL LTR(78%)]

[LGL A4(83%)]

[A4 LTR(94%)]

[EXE LTR(104%)]

[A5 A4(141%)]

25%, 50%, 150%, 200%, 400%

[Custom: 25-400%)]

Scan: 600x300dpi , Printing : 600x600dpi

Scan: 600x300dpi , Printing : 600x600dpi

Platen) Scan : 600x600dpi,

Printing : 1200x1200dpi

ADF) Scan : 600x300dpi,

Printing : 600x600dpi

Yes(Mono Only)

3 level

Yes(ADF Only), flushing if Memory full

Yes(Platen Only)

Yes(Platen Only)

No

No

No

No

No

No

2-up, 4-up (ADF only)

Yes (Platen Only)

Yes(Platen Only, x9 Only)

Service Manual

2-5

Samsung Electronics

Product Specifications

2.2.5 Fax

CLX-3160 Series

Compatibility

Communication System

Modem Speed

TX Speed

Compression

Color Fax

ECM

Resolution Std

Fine

S.Fine

Scan speed Std

Fine

S.Fine

Multiple page scan speed

Telephone Features Handset

On hook Dial

Search

1-Touch Dial

Speed Dial

TAD I/F

Tone/Pulse

Pause

N/A

N/A

Auto Redial N/A

Last Number Redial N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

Functions

Distinctive Ring

Caller ID

N/A

N/A

External Phone Interface N/A

Mail Box

Voice Request

TTI

N/A

N/A

N/A

RTI

Polling

Earth/Recall

Auto Reduction

SMS

RDC

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

CLX-3160N Spec.

2-6

Service Manual

CLX-3160FN Spec.

ITU-T G3

PSTN/PABX

33.6Kbps

3sec

MH/MR/MMR/JBIG/JPEG

Default (But Memory Transmission & Any

Reserved Transmission are not supported.)

Yes

203x98dpi

203x196dpi

300x300dpi

3sec/LTR (ADF)

5sec/LTR (ADF)

6sec/LTR (ADF)

20 ppm/LTR

Yes

No

Yes

No

No

Yes

Yes

No

No

Yes

No

Yes

No

Yes

Yes(Phone Book)

30

240 locations

Yes

Selectable in Tech Mode

Yes

Yes

Yes

Samsung Electronics

Report &

List Print out

CLX-3160 Series

Tx/Rx Journal

Confirmation

Sound Control

Auto Dial List

System Data List

Ring Volume

Key Volume

Speaker

Alarm Volume

Junk Fax barrier

Security Receive

Battery Backup

Rx fax duplex print out

Receive Mode

Capacity

Optional Memory

Max locations to store to 1 Group Dial

Fax Forward to FAX

Fax Forward to e-mail

Broadcasting

Cover page

Delayed fax

Memory RX

Mail Box (Electronic)

Voice Request

TTI

RTI

Polling

Earth/Recall

Auto Reduction

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

CLX-3160N Spec.

Product Specifications

CLX-3160FN Spec.

Yes

2 types available (with Image TCR, w/o image TCR)

Yes

List all user setting

Yes(Off,Low,MED,HIGH)

Yes(On,Off)

Yes(On,Off)

Yes(On,Off)

Yes

Yes

Yes (Up to 43 hours target)

No

Fax, TEL, Ans/Fax

4MB(320 Pages, Mono)

No

240 locations

Yes(On/Off), both Sent and Received

No up to 249 locations

No

Yes (Tx only, Mono only)

Yes

No

No

Yes

Yes

No

No

Yes (On,Off)

Service Manual

2-7

Samsung Electronics

Product Specifications

2.2.6 Paper Handling

CLX-3160 Series CLX-3160N Spec.

CLX-3160FN Spec.

Standard Capa.

Max. Capa.

Printing Max. Size

Min. Size

Margin(T/B/L/R)

150-sheet Semi Cassette Tray

400 sheets @75g/

216 x 356mm (8.5" x 14")

76 x 127 mm (3" x 5")

4 mm, 4 mm, 4 mm, 4 mm

150-sheet Semi Cassette Tray

400 sheets @75g/

216 x 356mm (8.5" x 14")

76 x 127 mm (3" x 5")

4 mm, 4 mm, 4 mm, 4 mm

Multi-purpose tray

Capacity

Media sizes

Media type

Media weight

Sensing

Standard Cassette Tray - Semi cassette type

Capacity

Media sizes

Media types

Media weight

Size sensor

User Interface

Sensing

Optional Cassette Tray

Capacity

Media sizes

Media types

Media weight

Size sensor

User Interface

Sensing

Output Stacking

Capacity FaceUp

FaceDown

Output Full sensing

1 sheet

76 x 127 mm (3" x 5") ~ 216 x 356 mm

(8.5" x 14")

1 sheet

76 x 127 mm (3" x 5") ~ 216 x 356 mm

(8.5" x 14")

Plain Paper, Thick Paper, Thin Paper,

Bond Paper, Color Paper, Card Stock,

Plain Paper, Thick Paper, Thin Paper,

Bond Paper, Color Paper, Card Stock,

Labels Transparency, Envelope, Preprinted Labels Transparency, Envelope, Preprinted

Cotton,Recycled Paper, Archive Cotton,Recycled Paper, Archive

16~43lb (60 to 163g/ )

Paper detection sensor

16~43lb (60 to 163g/ )

Paper detection sensor

150 sheets @ 75g/

76 x 127 mm (3" x 5") ~ 216 x 356 mm

(8.5" x 14")

Envelopes, Labels, Card stock,

Transparency(mono only) Papers (Preprinted, recycled)

16~43lb (60 to 163g/ )

N/A

No indicator, Cover

Paper detection sensor

250 sheets

A4,Letter,Legal, Folio, A5

Plain Paper

16~24lb (60 to 90g/ , , )

N/A

No Indicator

Paper empty sensor

N/A

100sheets @ 75g/

Yes

150 sheets @ 75g/

76 x 127 mm (3" x 5") ~ 216 x 356 mm

(8.5" x 14")

Envelopes, Labels, Card stock,

Transparency(mono only) Papers (Preprinted, recycled)

16~43lb (60 to 163g/ )

N/A

No indicator, Cover

Paper empty sensor

250 sheets

A4,Letter,Legal, Folio, A5

Plain Paper

16~24lb (60 to 90g/ , , )

N/A

No Indicator

Paper empty sensor

N/A

100 sheets @ 75g/

Yes

2-8

Service Manual

Samsung Electronics

CLX-3160 Series

Duplex

Supporting

Throughput

Media sizes

Media types

Media weight

ADF

Paper Weight

Capacity

Document Size

Dimension

Weight

Product Specifications

CLX-3160N Spec.

Manual

N/A

N/A

N/A

N/A

12.5~28lb (Non Coating)

50 sheets ( 20lb, 75 g/ )

Width: 142 ~ 216mm (5.6" ~ 8.5")

Length : 148 ~ 356mm (5.8" ~ 14.0")

460(W)x 3430(D) x 95(H) mm

5.6kg (, )

CLX-3160FN Spec.

Manual

N/A

N/A

N/A

N/A

12.5~28lb (Non Coating)

50 sheets ( 20lb, 75 g/ )

Width: 142 ~ 216mm (5.6" ~ 8.5")

Length : 148 ~ 356mm (5.8" ~ 14.0")

460(W)x 343(D) x 95(H) mm

5.6kg (, )

Samsung Electronics

Service Manual

2-9

Product Specifications

2.2.7 Consumables

CRU

No. of CRUs

CLX-3160 Series CLX-3160N Spec.

CLX-3160FN Spec.

Toner Black

Color

Key

Life detect

Replace method

Imaging Kit

(OPC+Deve)

Yield

Key

Sensor

Replace method

Waste Toner Bottle Yield

Key

FRU

No. of FRUs

ITB

Fuser

T2 Roller

Pick-up Roller

Yield

Key

Yield

Key

Yield

Key

Sensor

Yield

Key

ADF Lubber PAD

ADF Pickup Roller

6 (C/M/Y/K toner, Imaging Unit, Waste toner box)

K toner: CLX-K3160A

C toner: CLX-C3160A

M toner : CLX-M3160A

Y toner: CLX-Y3160A

Imaging unit: CLP-R300A (CLP-300 Series)

Waste toner box: CLP-W300A (CLP-300 Series)

CMY Rainbow kit: CLX-P3160A

2,000 A4/Letter pages, at ISO-19752 Std.

Coverage, Semi glossy

1,000 A4/Letter pages, at ISO-19752 Std.

Coverage, Semi glossy

Unique, Electronic key(CRUM)

Toner Level Sensor

Remain % method

90% : warning

100% : empty

120% : hardstop

CMY key

3 step for install/replacing

Approx. 20K black pages

(or 12.5K color pages)

Unique, Electronic key(CRUM)

None, that would be traced via software

6 steps for install/replacing

1,250 sheets (Full Color Std. Image) or

5,000 images

N/A

6 (C/M/Y/K toner, Imaging Unit, Waste toner box)

K toner: CLX-K3160A

C toner: CLX-C3160A

M toner : CLX-M3160A

Y toner: CLX-Y3160A

Imaging unit: CLP-R300A (CLP-300 Series)

Waste toner box: CLP-W300A (CLP-300 Series)

CMY Rainbow kit: CLX-P3160A

2,000 A4/Letter pages, at ISO-19752 Std.

Coverage, Semi glossy

1,000 A4/Letter pages, at ISO-19752 Std.

Coverage, Semi glossy

Unique, Electronic key(CRUM)

Toner Level Sensor

Remain % method

90% : warning

100% : empty

120% : hardstop

CMY key

3 step for install/replacing

Approx. 20K black pages

(or 12.5K color pages)

Unique, Electronic key(CRUM)

None, that would be traced via software

6 steps for install/replacing

1,250 sheets (Full Color Std. Image) or

5,000 images

N/A

4 (ITB, Fuser, T2 roller, Pick-up roller) 4 (ITB, Fuser, T2 roller, Pick-up roller)

Approx. 60K black pages (or 15K color pages) Approx. 60K black pages (or 15K color pages)

None None

None None

100,000 sheets B&W or 50,000 sheets Color 100,000 sheets B&W or 50,000 sheets Color

None None

100,000 sheets, Replacable

None

50,000 sheets, Replacable

None

100K

100K

100,000 sheets, Replacable

None

50,000 sheets, Replacable

None

100K

100K

2-10

Service Manual

Samsung Electronics

Product Specifications

2.2.8 Reliability & Service

CLX-3160 Series

Printing Volume(AMPV)

Max Monthly Duty

MPBF

MTTR

SET Life Cycle

Real-time Clock

System-record

Test Print

RDC

Temperature

Humidity

Comm. Mode

Operation

Operating

Storage (Packed)

Operating

Storage (Packed)

CLX-3160N Spec.

CLX-3160FN Spec.

360 page / B&W, 240 page / Color

24,200 images

40,000 pages (color 29,091 Mono 10,909

Total 40,000 image)

< 30 min.

200,000 image or 5 years

360 page / B&W, 240 page / Color

24,200 images

40,000 pages (color 29,091 Mono 10,909

Total 40,000 image)

< 30 min.

200,000 image or 5 years

None None

Total image count

Total page count (color/mono)

Imaging unit life

Fuser lifeTransfer roller life

Total image count

Total page count (color/mono)

Imaging unit life

Fuser lifeTransfer roller life

Transfer unit life

Toner image count (CMYK)

Transfer unit life

Toner image count (CMYK)

Tray roller life Tray roller life

Cartridge Coverage Machine Installed date Cartridge Coverage Machine Installed date

Configuration Sheet

Network Configuration Sheet

N/A

Configuration Sheet

Network Configuration Sheet

N/A

N/A

10 ~ 32.5 (59 ~ 90.5F)

-20 ~ 40 (-4 ~ 104F)

30 ~ 80% RH

30 ~ 85% RH

N/A

10 ~ 32.5 (59 ~ 90.5F)

-20 ~ 40 (-4 ~ 104F)

30 ~ 80% RH

30 ~ 85% RH

Samsung Electronics

Service Manual

2-11

Product Specifications

2.2.9 Environment

CLX-3160 Series CLX-3160N Spec.

Acoustic Noise

Level(Sound

Power/Pressure)

Input Voltages

Printing

Copying

Standby

Sleep

Less than 49.0 dBA (B/W printing)

Less than 52.0 dBA

Less than 35 dBA

Background noise level

110-127 VAC, 50/60Hz

220-240 VAC, 50/60Hz

Power Consumption

Certification

Emission

Dimension

(W x D x H)

Weight

Ready

AVG.

Max/Peak

Sleep/Power Off

Telecommunication

Environmental

Power Switch

Less than 160w

Less than 350W

*Curre n cy : 5A(110V) / 3A(220V)

700W/1KW

Less than 30W

N/A

Safety

EMC/EMI

Ozone

Dust

Styrene

VOC

Energy star, TCO99 or TCO03/Swan/

Blue Angel, PTS (BAM)

Europe : TUV(GS), SEMKO(IEC950/

EN60950), CB

FCC Class B

CE class B

0

0

0

0

Set(mm)

Set Packing

460(W)x429(D)x486(H)

610(W)x570(D)x638(H)

Set (with consumables) 19.5 Kg

Set Packing 26.0 Kg

Consumable - Imaging Unit : 3.2 Kg

- Toner Cartridge(C/M/Y each) : 0.102 Kg

- Toner Cartridge(Black) : 0.176 Kg

Consumable Packing - Imaging Unit : 4.0 Kg

- Toner Cartridge(C/M/Y each) : 0.110 Kg

- Toner Cartridge(Black) : 0.180 Kg

CLX-3160FN Spec.

Less than 49.0 dBA (B/W printing)

Less than 52.0 dBA

Less than 35 dBA

Background noise level

110-127 VAC, 50/60Hz

220-240 VAC, 50/60Hz

Power Switch

Less than 160w

Less than 350W

*Currency : 5A(110V) / 3A(220V)

700W/1KW

Less than 30W

N/A

Energy star, TCO99 or TCO03/Swan/

Blue Angel, PTS (BAM)

Europe : TUV(GS), SEMKO(IEC950/

EN60950), CB

FCC Class B

CE class B

0

0

0

0

460(W)x429(D)x486(H)

610(W)x570(D)x638(H)

19.5 Kg

26.0 Kg

- Imaging Unit : 3.2 Kg

- Toner Cartridge(C/M/Y each) : 0.102 Kg

- Toner Cartridge(Black) : 0.176 Kg

- Imaging Unit : 4.0 Kg

- Toner Cartridge(C/M/Y each) : 0.110 Kg

- Toner Cartridge(Black) : 0.180 Kg

2-12

Service Manual

Samsung Electronics

Product Specifications

2.2.10 Packing & Accessory

CLX-3160 Series

In-Box

CLX-3160N Spec.

Set

C/M/Y/K to be installed

Power cord

USB cable (China, Korea, India, Russia)

Set-up CD (Driver, manual), Application

N/W CD (SyncThru, manual)

Quick installation Guide sheet

Warranty book

CLX-3160FN Spec.

Set

C/M/Y/K to be installed

Power cord

USB cable (China, Korea, India, Russia)

Set-up CD (Driver, manual), Application

N/W CD (SyncThru, manual)

Quick installation Guide sheet

Warranty book

2.2.11 Options

CLX-3160 Series

Second Cassette

Memory

PostScript

Network

Wireless Network

Hard Disk

Duplex Unit

CLX-3160N Spec.

250-sheet SCF

N/A

N/A

Default

N/A

N/A

N/A

CLX-3160FN Spec.

250-sheet SCF

N/A

N/A

Default

N/A

N/A

N/A

Samsung Electronics

Service Manual

2-13

Product Specifications

2.3 Model Comparison Table

Canon

MF8170C

Ricoh Samsung

CLX-3160FN

2-14

Service Manual

Samsung Electronics

3

3. System Overview

This chapter describes the functions and operating principles of the main components.

3.1 System Structure

3.1.1 Main Parts of System

System Overview

Engine Part

Samsung Electronics

4

5

1

2

3

Paper Cassette Input

Paper Cassette Output

2 nd

Transfer Roller

6

7

8

1 st

Transfer Roller

OPC (Organic Photo Conductor)

Developers (Y, M, C, & K)

Fuser

9

ITB (Intermediate Transfer Belt)

Toner Kits (Y, M, C, & K)

Service Manual

3-1

System Overview

Cassette

Feeding Method : Cassette Type

Feeding Standard : Center Loading

Feeding Capacity : Cassette 150 Sheets(75g/ , 20lb Paper Standard)

No Manual Feeder

Paper Detecting Sensor : Photo Sensor (Empty, Registration, Exit)

Paper Size Sensor : None

LSU(Laser Scan Unit)

Consisted of LD(Laser Diode) and Polygon Motor Control.

Error

Polygon Motor Error

Hsync Error

Phenomenon

The Rotation of Polygon Motor can not reach stable

Though the rotation of Polygon Motor reach stable, the signal of Hsync is not occurred

2 nd Transfer Ass y

The life span: Print over 100,000 sheets (in 15~30 )

Specification: Similar to CLP-300 Series

Fuser Ass y

Heat Lamp : New Part - Knuckle Type

Heat Roller : Similar to CLP-300 Series

2 Pressure Roller : One is similar to HummingBird, the Other is a new added part comparing with other Fuser

Thermistor - Temperature-Measuring Device

Thermostat - Critical Temperature-Detecting Device

Fusing Temp. (180 )

H/W Protection Temp. (185 )

&

ITB(Intermediate Transfer Belt) & 1st Transfer Roller

The life span: Print over 100,000 Images

The ITB unit includes 1st Transfer Roller

&

OPC(Organic Photo-Conductor) & Developer

The life span: Print over 44,000 Images (Both)

Imagine Unit consists of 4 kinds of Developer , OPC, and Deve. Main Frame

Toner Kits

The life span: Color -> 1000 images (Std. Coverage Print-Out)

Black -> 2000 images (Std. Coverage Print-Out)

Driver Ass y

It is a power delivery unit by gearing

By driving the motor, it supplies the power to the feeding unit, the fusing unit, and the distributing unit.

The Main Motor is similar to CLP-300 Series Main Motor.

3-2

Service Manual

Samsung Electronics

3.1.2 Scanner( ADF)

3 in 1 : CLX-3160N

4 in 1 : CLX-3160FN

Scanning Method: Color CCD(600 x 1200 dpi)

Scan speed : SDMP 28cpm/MDSP 20cpm

Roller-ADF

Roller-Pickup

System Overview

Roller-Exit

Roller-Feed

Samsung Electronics

Service Manual

3-3

System Overview

3.1.3 FAX Section

Modem Part

BLOCK DIAGRAM

Implemented by based on Conexant DAA (Data Access Arrangement) Solution, and is roughly composed of two kinds

Chip Solution

- CX86710 (SFX336): Existing Modem Chip which adds SSD (System Side Device) for interfacing between LSD and

DIB of FM336Plus Core

- CX20493 (LSD) : LIU (Line Interface Unit) Chip which is controlled by SSD and satisfies each PSTN Requirements by modulating internal Configuration with connecting Tel Line.

3-4

Service Manual

Samsung Electronics

Modem (SFX336) specification.

2-wire half-duplex fax modem modes with send and receive data rates up to 33,600 bps

V.17, V.34, V.29, V.27 ter, and V.21 Channel 2

Short train option in V.17 and V.27 ter

PSTN session starting

V.8 and V.8bis signaling

HDLC support at all speeds

Flag generation, 0-bit stuffing, ITU CRC-16 or CRC-32 calculation and generation

Flag detection, 0-bit deletion, ITU CRC-16 or CRC-32 check sum error detection

FSK flag pattern detection during high-speed receiving

Tone modes and features

Programmable single or dual tone generation

DTMF receiver

Tone detection with three programmable tone detectors

Receive dynamic range:

0 dBm to -43 dBm for V.17, V.29, V.27 ter and V.21 Channel 2

9dBm to -43 dBm for V.34 half-duplex

Digital speaker output to monitor received signal

Two16-byte FIFO data buffers for burst data transfer with extension up to 255 bytes

V.21 Channel 1Flag detect

V.21 Channel 1Flag detect

+3.3V only operation

Typical power consumption

Normal mode: 264 mW

System Overview

Samsung Electronics

Service Manual

3-5

System Overview

Signal Transition of DAA Solution

Line Interface Signal of Tel Line and LSD is Analog Signal.

2) there is A/D, D/A Converter in LSD, so Analog Signal from Tel Line is converted in Digital through A/D Converter in

DAA and transfer to SSD by DIB Capacitor

Digital Signal from SSD is converted to Analog by D/A Converter in DAA and transfer to Tel Line

Transformer transfer Clock from SSD to LSD and Clock Frequency is 4.032MHz.

LSD full wave rectifies Clock to use as inner Power supply and also use as Main Clock for DIB Protocol Sync between

LSD and SSD. Transformer transfer Clock by separating Primary and Secondary, and amplifies Clock Level to LSD by Coil Turns Ratio 1:1.16.

Clock

- Clock is supplied by transformer from SSD to LSD, and there is PWROUT to adjust output impedance of Clock

Out Driver is inside SSD and CLKSHIGH Resistor to adjust duty of HLPWR Resistor and Clock.

SSD

CLKP

CLKN

DIBP

DIBN

LSD

Clock from SSD to LSD has Differential structure of 180 phase difference for Noise Robustness

DIB Data transfer Data from SSD to LSD by Transformer, and also transfer specific data from LSD to SSD.

After transferring data from SSD, RSP is transferred and LSD recognizes RSP and change LSD to output Driver transfer

Data to SSD.

DIB Data form SSD to LSD by Transformer has Differential structure of 180 phase difference between DIBP and DIBN for Noise Robustness

3-6

Service Manual

Samsung Electronics

System Overview

3.1.4 Line Interface Part

This is Connection Part between system and PSTN(Public Switched Telephone Network), and primary circuit is usually located. Main functions are Line Interface, Telephone Connection and Line Condition Monitoring.

1 Telephone Line Connection

Modular Plug : RJ-11C

LIU PBA Modular Type : 623 PCB4-4

Line Code Length : 2500 50mm

Line Code Color : Black

ON HOOK state Characteristic

1) DC Resistance

DP Dial Mode (Direct Current 30mA) : 50 ~ 300ohm

DTMF Dial Mode (Direct Current 20mA) : 50 ~ 540ohm

2) Ring Sensitivity

Ring detection Voltage : 40Vrms 150Vrms (condition : Current = 25mA, Frequency = 15Hz) product Margin : 30Vrms 150Vrms

Ring detection Frequency : 15.3Hz 68Hz (condition : Voltage = 45Vrms, Current = 25mA ) product Margin : 15Hz 70Hz

Ring detection Current : 20mA 100mA (condition : Voltage = 40Vrms, Frequency = 20Hz) product Margin : over 15mA

3) False Ring Sound

Ring Frequency : 750 Hz + 1020 Hz

Ring interrupt Cycle : On/Off depending on input Ring Signal Cycle.

Service Manual

3-7

Samsung Electronics

System Overview

3.1.5 Scan Part

Pictorial signal input part: output signal of CCD passes through Bypass Cap change to ADC at HT82V26, and defined signal between HT82V26 and CHORUSm processes the Image signal. When AFE accept each pixel, CDS(Correlated

Double Sampling ) technique which samples arm-level twice is used on each pixel by using CIP4e signal.

2) Pictorial image processing part: read CCD Pixel data in terms of 600dpi Line and process Error Diffusion Algorithm on

Text mode and Photo mode, and then store Data at Scan Buffer on PC Scan mode without algorithm.

On every mode Shading Correction and Gamma Correction are executed ahead, then processing is executed later.

* Scan Image Control Specification

Minimum Scan Line Time : 0.7062ms

Scan Resolution : Max. 600DPI

Scan Width : 216mm main function

- Internal 12bit ADC

- White Shading Correction

- Gamma Correction

- CCD Interface

- 256 Gray Scale

3) CCD Operating Part : CCD Image sensor use +5V and Inverter uses +24V

- CCD Maximum Operating Frequency : 10MHz

- CCD Line time : 0.7062ms

- White Data output Voltage : 0.7V 0.5V (Mono Copy, 0.75ms/line)

- Maximum Inverter Current : 600 mA Max.( +24V)

3.1.6 OPE Pannel Section

(1) Configuration

Operations Panel uses Main Control and separated OPE Chip Micom and work as inner program, systemic operation is serial system which exchange Date with SIO Port of Main Control. OPE Panel is approximately composed of Micom part, Matrix part and LCD.

(2) Micom controller

Micom has ROM, RAM, I/O Port built-in and displays and lights LCD by CPU command of Main Control Part and report

Key recognition Data to Main Control Board.

3-8

Service Manual

Samsung Electronics

3.1.7 EP Process

- Structure of EP Process

System Overview

Samsung Electronics

Service Manual

3-9

System Overview

- System Outline

Fuser

Paper path

OPC

Exit

Toner

Cartridge

ITB

LSU

Cassette

Charging

Conductive Roller charging

Roller resistivity : ~ 10^5 ohm-cm

Applied voltage : -1.1kV

Charge acceptance : -520V

OPC coating thickness : 21um

OPC diameter : 60mm

Non eraser system

1. Organic Photoconductor is charged to uniform voltage by conductive roll charging method

2. No ozone is produced because corona is not used

3. Charger roll is cleaned with cleaning roll

4. Toner remained on OPC after T1 process is cleaned by cleaning blade and retrieved into waste toner box by auger and belt driving mechanism

3-10

Service Manual

Samsung Electronics

Exposing

One polygon motor ( 6 facet )

Single beam LD (1ea)

LD wavelength : 785nm

Polygon motor rpm : 23747.5

LSU energy : 0.25uJ/cm^2

OPC exposed potential : -50V

1. Exposing is implemented by laser striking on to OPC with uniform potential

2. Laser beam is modulated according to image to be printed that is from PC

3. Latent Image is formed on OPC, which is developed with toner

Developing

Non-magnetic, mono component

Non-contact development

Developing bias : DC + AC

AC peak to peak : 1.5 ~ 2.0kV

Mass on developing roller : 550 ~ 600ug/cm^2

Toner coulomb : 15 ~ 20uC/g

Roller diameter : 10mm

Roller resistivity : 10^5 ~ 10^6 ohm-cm

Process speed ratio : 1.2 (OPC=1.0)

Color order : Y -> M -> C -> K

1. Only latent image formed by exposing process is developed with toner

2. AC + DC Voltage is being used to develop toner into latent image on OPC because non-contact developing method is adopted

3. Y, M, C, and K Images are sequentially developed onto OPC and transferred onto Intermediate

Transfer Belt (hereafter ITB) to form a color image on ITB

4. Toner Bottles are used to supply toner into developer compartment

5. Toner level is being sensed to control toner supply from toner bottle to developer

Transfer 1

Multi-pass transfer

Indirect transfer

Transfer voltage : 0.5 ~ 2.0kV (controllable)

Roller diameter : 14mm

Roller resistivity : ~ 10^7 ohm-cm

Belt resistivity : 10^9 ~ 10^11 ohm-cm

Environment sensing by Y-transfer roller

Transfer unit life : 50K images

1. Developed Image on OPC is transferred onto ITB by T1 Process

2. T1 Voltage is positive which attract toner to ITB

3. 4 times of T1 process is required to make a color image on ITB, which means multi-pass process

4. ITB has a hole as a fiducial mark for timing. Engine control for color image is synchronous with it,

ITB Home Sensing Signal

System Overview

Service Manual

3-11

Samsung Electronics

System Overview

Transfer 2

Indirect transfer

Transfer voltage : 1 ~ 4.0kV (controllable)

Roller diameter : 18.6mm

Roller resistivity : ~ 10^7 ohm-cm

Belt resistivity : 10^9 ~ 10^11 ohm-cm

Transfer unit life : 50 K images

1. Color image formed on ITB is transferred onto media by T2 process

2. T2 voltage is also positive to get color image moved onto media

3. Toner remained on ITB after T2 process is cleaning by ITB cleaning blade and collected and

4. Transported and retrieved into waste toner box by auger and belt driving system

5. T2 Roll is engaged when color image is being transferred onto media. Otherwise it is disengaged. Clutch is used for driving T2 Roll engagement and disengagement

Fusing

3 Roll system

-> short warm-up time (45sec)

Post Pressure Roll

1. Color Image on media is melted down and fixed into media by fusing process

3-12

Service Manual

Samsung Electronics

System Overview

3.1.8 Copier Section

Copy Mode:

Scanner Type;

Maximum Size of Original:

(max. width = 218 mm, max length = 400 mm)

Optical Resolution:

Copy Quality - H x V:

(User selectable via Content button)

Supported Media Types:

Copy Speed:

(SDMP = Single Document,

Multiple Printout,

MDSP = Multiple Document,

Single Printout)

Reduce/Enlarge:

Non-printable Area:

Copy Count:

(Page count displayed on LCD during copy operation)

Copy Modes:

Fixed R/E Setting:

Darkness Control:

First Copy Output Time (FCOT):

Black and White

CCD with Flatbed/Platen and ADF

-Platen: 216 x 297 mm

-ADF: Legal (216 x 356 mm)

600 x 600 dpi

-Text : 600 x 300 dpi (default)

-Text/Photo : 600 x 300 dpi

-Photo : 600 x 600 dpi

Plain, Label, Cardstock, Transparency

-Platen, SDMP: 30cpm (Letter)

-ADF, SDMP: 30cpm (Letter)

-ADF, MDSP: 20cpm (A4, Text or Text/Photo)

10cpm (A4, Photo)

-Platen: 25% - 400% (1% increments)

-ADF: 25% - 100% (1% increments)

4 mm (Top, Bottom, and each Side)

1 to 199

Text, Text/Photo, Photo

100%, Auto-fit, 2(4)-Up

3 levels

-Platen: 8.5 sec. (600 x 300 dpi)

-ADF: 15 sec. (600 x 300 dpi)

3.1.9 Telephone Section

Speed Dial:

On-hook Dial (manual fax):

Last Number Redial:

Automatic Redial:

Pause:

Ringer Volume:

Tone/Pulse:

400 Locations (46 digits maximum per location)

Yes

Yes

Yes

Yes (using Redial key)

Off, Low, Medium, High

Selectable (Tech Mode Only no Telecom certification for Pulse mode)

Service Manual

3-13

Samsung Electronics

System Overview

3.2 Main PBA Description

3.2.1 Print Board Assembled(PBA) Pictures

1) Top View of Main Controller

2) Bottom View of Main Controller

3-14

Service Manual

Samsung Electronics

3) Top View of SMPS

System Overview

4) Bottom View of SMPS

Samsung Electronics

Service Manual

3-15

System Overview

5) Top View of HVPS

6) Bottom View of HVPS

3-16

Service Manual

Samsung Electronics

7) Top View of OPE

8) Bottom View of OPE

System Overview

Samsung Electronics

Service Manual

3-17

System Overview

9) Top View of FAX

10) Bottom View of FAX

3-18

Service Manual

Samsung Electronics

System Overview

11) Top View of ADF

12) Bottom View of ADF

Samsung Electronics

Service Manual

3-19

System Overview

13) Top View of Joint B'D

14) Bottom View of Joint B'D

3-20

Service Manual

Samsung Electronics

3.2.2 Main PBA

System Overview

Samsung Electronics

Service Manual

3-21

System Overview

3.2.3 Main PBA Description

1) CHORUSm

CHORUSm involves in itself the functions to control ARM Processor Core and various H/W devices. CHORUSm, therefore, controls Main PBA and all engine mechanism, processing the print job received from host and enabling the engine to print image.

Function

Process

0.13um Technology

Package

496 PBGA

CPU Core

ARM 920T - 300MHz

Cache : I-Cache 16KB, D-Cache 16KB

System Bus

32-bit width, 100MHz

SDRAM Controller

32-bit width, 100MHz operation

5 Banks, Up to 128MB Address space per Bank

Programmable Timing to Control SDRAM A.C Characteristics

Support Self Refresh for Data Retention

ROM Controller

32-bit width, 4 Banks, Up to 16MB Address space per Bank

Burst Capability

Programmable Timing per Bank

3-22

Service Manual

Samsung Electronics

System Overview

IO Controller

6 Channels, Up to 16MB Address space per Bank

Programmable Timing per Bank

DMA Controller

6 Channels General Purpose DMA

HPVC Controller

Hyper Printer Video Controller

High Performance DMA-based Interface to Printer Engine

Support Dual/Single Beam LSU, LVDS Video Output

Support A3, 1200dpi

UART Controller

5 Channels Indepenent Full Duplex UART

Interrupt Controller

Support 6 External Interrupts

Support 26 Internal Interrupts

Timer Controller

6 System Timers and Watch Dog Timer for S/W Trap

Scanner Controller

300/400/600/1200dpi CIS/CCD Interface

Color/Mono grey image, Binary image scan support

600dpi Color/Mono Copy support

Image Processing for High-End MFP,Digital Copier

MH/MR/MMR CODEC for Fax

Scan image : A4 1200dpi processing

Copy image : A4 600dpi processing

MAC Controller

10/100Mbps

Full IEEE 802.3 compatibility

PPI Controller

IEEE1284 compliant parallel port interface

DMA-Based or Interrupt-Based operation

GEU Controller

Graphic Engine Unit for Banding support of Printer Language

Scan Line Buffer, Polygon Filling

CODEC Controller

2 Channels JBIG Encoding and Decoding

I2C Controller

1 Channel, Operated at max frequency 400kHz

RTC Controller

Engine Controller

LSU Control and Interface Unit

2 Channels STEP Motor Control Unit

8 Channels PWM Control Unit

8 Channels ADC Control Unit

2 Channels DAC Control Unit

Samsung Electronics

Service Manual

3-23

System Overview

CHORUSm (Internal Block Diagram)

3-24

Service Manual

Samsung Electronics

System Overview

2) System Memory Block

Memory saves program and video data and print jobs received from host. Its volume is 64MB with network function and 32MB without network function. It has no separate device for extension. SDRAM is used, driven at width of 32-bit and 100MHz, and controlled by memory controller built in CHORUSm.

3) Flash Memory Block

Flash memory is the space used for saving program. Its volume is 4MB with network function and 2MB without network function. It has no separate device for extension. NOR type flash memory is used and accessed at 32-bit width burst, being controlled by the ROM controller built in CHORUSm.

4) USB2.0 Device Block

This block supports USB2.0 high speed (480Mbps). ISP1582 of Philips company is used and connected to the IO

Bus of CHORUSm at 16-bit, controlled by IO controller built in CHORUSm. Through this I/O port it receives print job from host.

5) Network Block

This block has 10/100Mbps wired network function and is controlled by MAC controller built in CHORUSm. It is connected to host through physical layer chip outside, and thus receives print job from host. STE100P is used for physical layer chip.

6) EEPROM Block

System EEPROM is controlled by the I2C controller built in CHORUSm, connected to the other non-volatile memory on I2C bus. It works at the speed of 400KHz. This system EEPROM contains all drive information and production information necessary for the operation of printer. Its size is 16k-bit.

7) OPE Control

The panel is driven in the form of PIO by UART controller built in CHORUSm.

8) LSU Control

Laser Scanning Unit is controlled by LSU controller built in CHORUSm. It makes use of all functions such as Polygon

Mirror Motor Control necessary for driving LSU and Synchronized Signal Generation Control, and helps to scan laser beam on the photosensitive drum to form latent image.

9) BLDC Control

It is controlled by BLDC controller built in CHORUSm. It controls the drive of printer mechanism and helps it to be driven at an equal speed.

10) Sensors Control

GPIO controller built in CHORUSm collects the status of all sensors. According to this status of sensors, it controls printer mechanism to help normal printing. There are sensors such as Paper Empty Sensor, Registration Sensor and

Developer Home Sensor, etc.

Service Manual

3-25

Samsung Electronics

System Overview

11) Clutches Control

GPIO Controller built in CHORUSm controls all clutches, which help printer to do print job normally. There are clutches such as Paper Pick-up Clutch, Registration Clutch, Developer Home Clutch, ITB Clutch, T2 Clutch, Fuser Clutch,

Developer Toner Supply Clutch, etc.

12) PWM Control

PWM Controller built in CHORUSm controls the parts that require PWM for normal printing, such as BLDC drive speed and HVPS high voltage level, etc.

13) ADC Control

It is controlled by ADC Controller built in CHORUSm, and is used for perception of charged voltage and current, 1st and 2nd transfer voltage and current, fusing temperature, used-up toner and toner amount, and interior temperature, etc.

14) DAC Control

It is controlled by DAC Controller built in CHORUSm and used to set standard level of light amount of LSU Laser

Diode.

3-26

Service Manual

Samsung Electronics

System Overview

3.2.4 SMPS(Switching Mode Power Supply) PBA

SMPS is consisted of SMPS part which supplies DC power for driving system and AC Heat Control part which supplies power to Fuser. Standard TYPE III is used.

1) DC Output

Main Controller PBA, OP Panel, BLDC, Sensors, Clutches, Other PBAs

2) AC Output

Fuser Unit(Heat Lamp, Thermostat)

3) Output Voltage

CHANNEL

V_out

Load

+5.0V

+5.0V +/-5%

MicroController,

CMOS, LOGIC

+24V

+24.0V +15%/-10%

LSU

+24VF

+24.0V +15%/-10%

MOTOR, CLUTCH,

HVPS

CON3 To Main PBA

CON1 AC Input

Samsung Electronics

Service Manual

3-27

System Overview

3.2.5 HVPS(High Voltage Power Supply) PBA

HVPS PBA generates high voltage of charger, supply, T1 and T2 which is supplied to Developer, ensuring optimum condition for image formation. HVPS receives input of 24V and generates high voltage, supplying it to Toner, OPC,

Cartridge, ITB Unit and Transfer Roller.

3-28

Service Manual

Samsung Electronics

System Overview

1) Charger Voltage : Charger

Function: voltage that charges OPC surface up to -500V~ -800V.

Output voltage: -1.0KV ~ -2.0KV DC 3%

Error type: if the voltage fails to be output to Charger Roll, OPC surface will not be charged, and the toner on the developer roller will be transferred to OPC Drum, printing black paper.

2) 1st Transfer High Voltage : T1(+)

Function: voltage necessary for transferring toner developed on OPC Drum surface onto ITB.

Output voltage: Max +2.0KV 3%(Duty variable, no load)

ERROR type: if T1(+) output fails, the toner on OPC drum will not be transferred to ITB normally and the image will be blurred.

3) 2nd Transfer High Voltage : T2(+)

Function: voltage used to transfer the toner primarily transferred on ITB again onto paper.

Output voltage: Max +5.0KV 3%(Duty variable, no load)

ERROR type: if T2(+) output fails, the toner on ITB will not be transferred to paper normally and the image will be blurred.

4) T2 Cleaning Voltage : Clean : T2(-)

Function: prevent reverse side of paper from being dirtied, by recovering the negatively charged toner remaining at

Transfer Roller and sending it onto ITB.

Output voltage: with no feedback control, output fixed voltage(-1300V +/- 15%)

ERROR type: reverse side of paper will be dirtied.

5) Supplying Voltage : Supply AC+DC(-)

Function: voltage that makes toner to develop on the area exposed by LSU by means of potential difference, output will be the voltage of AC+DC overlapped form.

Output voltage: AC 600V ~ 2000V p-p +/-1.5%

DC -50V ~ -600V DC +/- 3%

ERROR type: 1. if supply is GND, density will be extremely low.

2. if supply is floating (for insecure terminal contact), density will be down so slightly that it is impossible to make out with naked eyes.

6) Developing Voltage : Deve AC+DC(-)

Function: voltage that supplies toner to Developing Roller

Output voltage: AC 300V ~ 1700Vp-p 1.5% (supply voltage is connected to ZENER Diode 300V)

DC -50V ~ -600V DC +/- 3%

ERROR type: 1. if Deve is GND, density will be extremely down.

2. if Deve is floating (for insecure terminal contact), density will be extremely down.

Service Manual

3-29

Samsung Electronics

System Overview

3.3 CRUM

In the case of Refill Toner Install

1) Perception of Refill Cartridge (when power is on or the cover is closed)

End of Life / life span data initialization -> judge to be Refill Cartridge

End of Life / life exhausted (simple refill) -> stop printing caused by life exhaustion

2) Operating

It is impossible to control appropriate development parameters, for there s no toner specification data.

It runs with the setting of default development parameter. (Image quality will be degraded, for the lack of appropriate respond to the change of time and environment.)

3) Service Response

It is possible to response appropriately, for the information of cartridge life is saved at Back Up Area.

Process after CRU life expiration

1) Record the information of End of Life.

2) Copy the information of Operating Area into Back up Area.

3) Write-Protect Back up Area.

4) Clear some information of Operation Area.

-> Supplier/Model Name/MFC date/Serial Number (Manufacture Information)

-> Let cartridge refiller initialize manufacture information and life span information.

3-30

Service Manual

Samsung Electronics

CRUM Position

Bottle

Agitator

Washer

Cap

Cap- CRUM

Seal

Agitator

Coupling

CRUM

System Overview

Samsung Electronics

Service Manual

3-31

System Overview

3.4 General Description

This chapter is the product specification for the CLX-3160FN Series. The CLX-3160FN Series is a Color Laser Printer.

The CLX-3160FN Series series can be expanded to multi functional printer (MFP). CLX-3160FN Series is developed for two target users. Those are small office users who sometimes need color printouts, and medium business users who mainly use B/W printouts. The main product concept is “the world smallest and lightest color laser printer”. This model has 16ppm B/W print-speed and 4ppm color print-speed, 2400 x 600 dpi class (optical 600 x 600 dpi) color laser printer.

3.4.1 Controller

-The video controller board is located on the right side of the printer.

-Basic Memory is 32 Mbytes SDRAM.

-Field F/W upgradeable FLASH ROM firmware for controller, 1024 byte EEPROM

-Printing Resolution :

Native 600 x 600 dpi standard

Resolution can be enhanced up to 2400 x 600 dpi class, 1200 x 600 dpi (default), 600 x 600 dpi

3.4.2 Processor

CHORUSm (300Mhz), Proprietary SOC

3.4.3 Printer Language Emulations

SPL-Color

3.4.4 Memory

The controller has 32 MB SDRAM and 4 MB flash ROM on Board.

3-32

Service Manual

Samsung Electronics

System Overview

3.4.5 Interfaces

The system supports the following standard interfaces:

One USB port

- USB v.2.0 compliant

- Color-coded to meet WHQL requirements, connector must be Pantone 426C

One 10/100 BaseT network connector

- The printer supports an internal Network Interface that can be installed pre-configured on the video controller board at the factory. This supports all of the major Network Operating Systems such as the Novell

NetWare, TCP/IP, etc. Details of the network specification will be provided separately.

3.4.6 OP Panel

4in1 OP panel : FAX + COPY + SCAN + PRINTER)

3in1 OP panel : COPY + SCAN + PRINTER

16 x 2 LINE CHARACTER LCD

MODE ( FAX, COPY, SCAN)

KEY TYPE: CARBON COATING S/W

3.4.7 Periodic Replacing Parts

Samsung shall specify parts requiring replacement and the frequency of replacement. The parts identified may be deemed customer replaceable parts. Periodic replacement parts shall be recommended as follows

* Average A4-/letter-sized page count based on Std. coverage of individual colors on each page. Usage conditions and print patterns may cause results to vary.

** Image counts based on one color on each page. If you print documents in full color (Cyan, Magenta, Yellow, Black), the life of this item will be reduced by 25%.

Service Manual

3-33

Samsung Electronics

System Overview

3.4.8 Power Switch

The Switch is located at rear-side of printer and must be marked to indicate on and off.

3.4.9 Operator Panel

(1) Configuration

Operations Panel uses Main Control and separated OPE Chip Micom and work as inner program, systemic operation is serial system which exchange Date with SIO Port of Main Control. OPE Panel is approximately composed of Micom part, Matrix part and LCD.

(2) Micom controller

Micom has ROM, RAM, I/O Port built-in and displays and lights LCD by CPU command of Main Control Part and report

Key recognition Data to Main Control Board.

3.4.10 Sensor

Paper empty (Cassette)

3.4.11 CRUMS

The CLX-3160 Series engine will be equipped with electronics that can read and write data into NVRAMs otherwise known as CRUMs that reside within 1) C, M, Y, K Toner cartridges and 2) Imaging kit(Developer, OPC, ITB). The CRUM has a company ID, and Samsunga electronics logo.

The toner CRUM also identifies the type of toner cartridge (Standard or High Capacity). The CRUMs contain fixed data such as the low warning point, specified life point, and hard stop point (on toner, not on IBT unit) and also store the current life count (pages count, pixels count, images count) and % of usage (gas gauge) data.

3.4.12 LOW / OUT Behavior for consumables

The consumable low and out behavior on CLX-3160 Series engine is specified by SEC.

FP message

Toner

Imaging Kit

Fuser

T2 Roller

Pick-up

Device for life end detection

CRUM

CRUM

No

No

No

Law(90%)

Yes

Yes

Yes

Yes

No

Life(100%)

Yes

Yes

Yes

Yes

No

Hard stop

Yes(115%)

No

No

No

No

Reset to 0

No

No

Yes

Yes

No

3-34

Service Manual

Samsung Electronics

4

4. S/W Structure and Descriptions

4.1 Overview

The software of Dove system is constructed with

1) Host Software part that the application software operated in Window and Web Environment, and

2) Firmware parts that is a Embedded software controls printing job.

S/W Structure and Descriptions

4.2 Architecture

Host Software is made up of

1. Graphic User Interface that offers the various editing functions to user in Host,

2. Driver that translates the received document to a Printing Command language which printer can understand and transfers data to spooler,

3. Stand-alone Application that offers the various printing application, DMS(Document Management System),

RCP(Remote Control Panel), Printer Status Monitor, Network Management in Window system,

4. Web-based-Application that offers the same functions as Stand-alone Application and RDC(Remote Diagnosis

Control) in Web environment.

Firmware is made up of

1. Application (Emulation) that is a interpreter translate data received from Host to a printing language (PCL, PS, GDI, etc.) to be able to make the user to take same output as originally one what composed in Host.

2. Kernel that control and management the whole procedure include of Control flow and Printing Job before transfer to

Service Manual

4-1

Samsung Electronics

S/W Structure and Descriptions

4.3 Data and Control Flow

The above Block Diagram is explained that:

Host Side is made up of

1. Driver that is Windows application software translate printed data to one of printer language and create spooler file,

2. Web-based Application that offer a various printer additional functions, management of printing job, printer administration, Status monitor to monitoring the printer status by real time in Web, independent environment on OS.

3. Stand-alone Application that is a similar Window software as same as above 2,

4. Port Monitor that manages the network communication between spooler and Network Interface Card, or various additional application and Network Interface Card,(this is, at first, make communication logical port, manage the data, transfer them from spooler to network port, and offer the result of printing).

4-2

Service Manual

Samsung Electronics

S/W Structure and Descriptions

Firmware Side is made up of

1. Network Interface Card is that relay the communication between Host and kernel using various network protocol,

2. Kernel is that manages the flow control of emulation procedure, receiving data from Host or Network card and printing with engine & rendering job,

3. Emulation is that interprets the various output data from selected emulation,

4. Engine is that prints rendered bit-map data to paper with required size and type by Kernel.

And then, for Job Spooling function for Multi-User, Multi-Printing that is occurred in Network printing and various additional printing functions, this Kernel use max. 10 Queuing systems in a memory.

In Printing, the two procedures are

(1) Case of using Parallel or USB Port

After user start to print the wanted document to PCL string or compressed GDI bit-map data, Driver translate the all graphic data of it and send data to host spooler. And then the spooler sends the data stream to the printer via parallel port or USB port.

Kernel receives this data from Host, and then select emulation fit to data and start selected one. After emulation job end, Kernel sends the output bit-map data to Engine using Printer Video Controller (by clock type for LSU).

Engine print the received data to required paper with the sequential developing process.

(2) Case of using Network Interface Card

After user start to print the wanted document to PCL string or compressed GDI bit-map data, Driver translate the all graphic data of it and send data to host spooler.

If so, Port monitor managing network port receives data from spooler and sends a data stream to the Network

Interface Card.

Network interface card receives it and send to Kernel part,

Kernel receives this data from Host, and then select emulation fit to data and start selected one. After emulation job end, Kernel sends the output bit-map data to Engine using Printer Video Controller (by clock type for LSU).

Engine print the received data to required paper with the sequential developing process.

The additional printing function are realized in

(1) Web environment

(2) Window environment.

On addition, Kernel informs a status of printing status and printer status to user made printing job with the Status Monitor.

Service Manual

4-3

Samsung Electronics

S/W Structure and Descriptions

4.4 Alarm Shortage

Toner (C,M,Y,K)

Transfer Belt

Fuser

Pickup Rollers

(MP/Tray1/Tray2)

90 ~ 100 %

Ready Yellow Toner Low

Replace Transfer Belt Soon

Replace Fuser Soon

100 ~ 110 %

Replace Yellow Toner

Replace Transfer Belt

Replace Fuser

Replace MP Pick-Roller

110 %~

Yellow Toner Empty

4.5 Error status

1. Missing/Invalid Consumables

Install Cyan (Magenta, Yellow, Black) Toner

Install Transfer Belt

Invalid Cyan (Magenta, Yellow, Black) Toner

Invalid Transfer Belt

2. Paper Empty/Mismatch

Paper Empty In MP(Tray1, Tray2)

Load A4 In MP(Tray1, Tray2)

3. Paper JAM

Jam 0 In MP(Tray1, Tray2)

Jam Inside Printer

Jam In Exit Area

4. Cover

Cover Open : Message toggles between

Cover Open and Install Transfer Belt

SCF Cove Open

5. Service Call : Unrecoverable Error

Engine LSU Error

Main Motor Error / Dev. Motor Error

Engine Fuser Over(Low) Heat Error

Rear Fan Error / Left Fan Error / SMPS Fan Error

6. Others

Memory Overflow Error

Ready IP Conflict

4-4

Service Manual

Samsung Electronics

S/W Structure and Descriptions

4.6 CRUM Overview

- Stands for “Customer Replaceable Unit Monitor”

- EEPROM is used for CRUM Memory.

- CRUM stores various information on consumables (including consumables’ life).

- In CLX-3160FN, total five CRUM’s are used

(four on toner cartridges and one on transfer belt)

CRUM stores the following information

Model Name

Supplier ID

Serial Number

Company ID

MFG Date

Capacity

Page Count

- Toner Cartridge and Transfer Belt

- Indicates how many pages are printed by using the consumable

Dot Count

- Toner Cartridge Only

- Indicates how many dots are printed by using the toner cartridge

4.7 FW Upgrade

Via USB or Network (SWS/SWAS)

You can upgrade F/W via USB or Network whenever the printer is “Ready”

Via Using F/W Download Mode :

Step 1) Power on while pressing the Online Key

Step 2) Press Online Key one more time if “Press Key Again” is displayed on LCD

Step 3) Download F/W via USB

Service Manual

4-5

Samsung Electronics

S/W Structure and Descriptions

4.8 Initailize Flow

4-6

Service Manual

Samsung Electronics

S/W Structure and Descriptions

Samsung Electronics

Service Manual

4-7

Disassembly and Reassembly

5

5. Disassembly and Reassembly

5.1 General Precautions on Disassembly

When you disassemble and reassemble components, you must use extreme caution. The close proximity of cables to moving parts makes proper

Releasing Plastic Latches

Many of the parts are held in place with plastic routing a must. latches. The latches break easily; release them

If components are removed, any cables disturbed carefully. by the procedure must be restored as close as

To remove such parts, press the hook end of the possible to their original positions. Before removlatch away from the part to which it is latched.

ing any component from the machine, note the cable routing that will be affected.

Whenever servicing the machine, you must perform as follows:

1. Check to verify that documents are not stored in memory.

2. Be sure to remove the toner cartridge before you disassemble parts.

3. Unplug the power cord.

4. Use a flat and clean surface.

5. Replace only with authorized components.

6. Do not force plastic-material components.

7. Make sure all components are in their proper position.

Service Manual

5-1

Samsung Electronics

Disassembly and Reassembly

5.2 Cover Upper (Left, Right)

1. Open the ADF Ass'y.

3. Apply light pressure to the right side of the Cover

Upper Right and pull it in the direction of arrow, as shown below.

ADF Ass'y

Cover Upper Right

2

1

2. Apply light pressure to the left side of the Cover Upper

Left and pull it in the direction of arrow, as shown below.

Cover Upper Left

1

2

5-2

Service Manual

Samsung Electronics

5.3 Front Cover

1. Open the Cover.

Disassembly and Reassembly

2. To remove the Front Cover, first pull the Rib below the right side of the Front Cover with a light pressure to the upside and then release the Front Cover in the direction of arrow, as shown below.

Front Cover

2

1

1

Rib

2

Samsung Electronics

Service Manual

5-3

Disassembly and Reassembly

5.4 OPC DEV Unit

1. First open the Front Cover and then pull the OPC

DEV Unit out of the machine using the open handle, as shown below.

2. Extend the Top Handle on the OPC DEV Unit and then use it to pull the OPC DEV Unit out of the machine completely.

Top Handle

OPC DEV Unit

Notice: 1) Do not touch the green surface on the OPC

DEV Unit with your hands or any other material.

Use the handle on it to avoid touching this area.

2) Be careful not to scratch the surface of the

OPC DEV Unit.

5-4

Service Manual

Samsung Electronics

5.5 ITB Unit

1. Before you remove the ITB Unit, you should remove:

- OPC DEV Unit (Refer to 5.4)

2. For easy dissembly, first pull the ITB Unit in the direction of arrow and then take out the ITB Unit, as shown below.

1

2

1

ITB Unit

Notice: 1) Do not grab the ITB Belt of the ITB Unit, it may cause a malfunction due to a foreign object.

2) Be careful not to scratch the surface of the ITB

Belt.

Disassembly and Reassembly

Service Manual

5-5

Samsung Electronics

Disassembly and Reassembly

5.6 T2 Roller Unit

1. Push the Open Button and then open the Rear Cover, as shown below.

2. To remove the T2 Roller Unit, first release the Holder and rotate it from the Transfer Unit and then take out the T2 Roller Unit, as shown below.

2

Holder

1

Open Button

Rear Cover

Transfer Unit

T2 Roller Unit

Notice : Do not grab the rubber part of the T2 Roller

Unit, it may cause a malfunction due to a foreigen object.

Hold the both side of the T2 Roller Unit when replacing it.

5.7 Rear Cover

1. Remove the seven screws securing the Round Cover and then release the Round Cover from the machine completely, as shown below.

2. Open the Rear Cover(refer to 5.5.1) and then release the Rear Cover in the direction of arrow, as shown below.

1

Rear Cover

Round Cover

2

3

5-6

Service Manual

Samsung Electronics

Disassembly and Reassembly

5.8 OPE Unit

1. Before you remove the OPE Unit, you should remove:

- Cover Upper L, R (Refer to 5.2)

2. Remove the two screws securing the OPE Unit to the

Platen Ass'y.

4. Unplug the three connectors from the OPE PBA, as shown below.

3. Apply light pressure to the front of the OPE Unit and pull it in the direction of arrow, as shown below.

5. Remove the nine screws securing the OPE PBA to the OPE Cover.

OPE Cover

OPE Unit

LCD

Cover

OPE PBA

Service Manual

5-7

Samsung Electronics

Disassembly and Reassembly

6. Remove the Contact Rubbers from the OPE Cover.

8. If necessary, remove the NEVI Cover.

Sheet

One Touch

Label

One Touch

NEVI Cover

Mode

Onetouch

Menu

Tel_Copy

7. Remove the Lens and Keys from the OPE Cover.

9. For easy disassembly, release the Battery-NIH.

Battery-NIH

Onetouch

FAX

Menu

LED Lens

Mode

Copy

Tel

Stop Clear

On Hook

Start Black

Start Color

5-8

Service Manual

Samsung Electronics

Disassembly and Reassembly

5.9 Side Cover (Left, Right)

1. Before you remove the Side Cover (Left, Right), you should remove:

- Front Cover (Refer to 5.3)

- Rear Cover (Refer to 5.7)

2. Remove the two screws securing the Right Side

Cover, as shown below.

4. Remove the two screws securing the Left Side Cover, as shown below.

3. Apply light pressure to the bottom of the Right Side

Cover and pull it to the right side in the direction of arrows, as shown below.

5. Apply light pressure to the bottom of the Left Side

Cover and pull it to the left side in the direction of arrows, as shown below.

Samsung Electronics

Right Side Cover

Left Side Cover

Notice : Be careful not to damage the hooks when remove the Side Cover (Left, Right).

Service Manual

5-9

Disassembly and Reassembly

5.10 ADF Ass'y

1. Open the ADF Ass'y

ADF Ass'y

3. To remove the ADF Engine part, first remove the eight screws securing the ADF Engine part to the Cover

Platen and then release the ADF Engine part in the direction of arrow.

At that time the TX Stacker automatically release it self at right side, as shown below.

ADF Engine part

TX Stacker

2. First remove the ADF Harness from the Platen Ass'y and then pull the ADF Ass'y upward in the direction of arrow, as shown below.

ADF Ass'y

4. Remove the two screws securing the ADF Harness to the Cover Connector and then take care to thread the

ADF Harness through the Cover Platen.

ADF Engine part

Connector Cover

ADF Harness

5-10

Service Manual

Samsung Electronics

Disassembly and Reassembly

5. Remove the Open Cover, as shown below.

Open Cover

7. To remove the ADF Upper, first remove the two screws securing the ADF Upper and then unlatch the two hooks using a flat-blade screwdriver, as shown below.

ADF Upper

2

1

2

1

1

2

2

6. Release the Bush and rotate it until it reaches the slot, as shown below and then lift the Pick Up Ass'y out in the direction of arrow.

Pick Up Ass'y

1

Bush

8. Unplug the ADF Motor connector and remove four screws securing the ADF Motor Ass'y and then remove the one screw securing the Ground Cable, as shown below.

Then take out the ADF Motor Ass'y.

ADF Motor Ass'y

2

ADF Lower

Notice : Do not grab the rubber part of the Pick Up Ass'y, it may cause a malfunction due to a foreigen object.

Notice : 1) When working on the ADF Motor Ass'y take care not to contaminate any of the rubber surfaces with grease.

2) Before removing the ADF Engine part take great care to note the position of the Ferrite

Core and the Motor Harness routing.

When refitting the ADF Engine part ensure that the Harness and Ferrite are properly located and are clear of the Motor Fan and

White Bar Clip.

Service Manual

5-11

Samsung Electronics

Disassembly and Reassembly

5.11 Platen Ass'y

1. Before you remove the Platen Ass'y, you should remove:

- OPE Unit (Refer to 5.8)

- Side Cover Left, Right (Refer to 5.9)

- ADF Ass'y (Refer to 5.10)

2. Remove the three screws securing the Platen Ass'y, as shown below.

4. First release the OPE Harness in the direction of arrow and then remove the one screw securing the

Ground Cable, as shown below.

OPE Harness

Ground Cable

3. First carefully release the cables(CCD, Scan, Ground) from the Harness Guide and then apply light pressure to the top of the Harness Guide and pull it to the right side in the direction of arrow, as shown below.

5. Unplug the two connectors(Scan, Out Full) and CCD

Cable and then lift the Platen Ass'y in the direction of arrow, as shown below.

Out Full

Platen Ass'y

CCD

Scan

2

1

3

Harness Guide

5-12

Service Manual

Samsung Electronics

6. Remove the four screws securing the Scan Upper.

Disassembly and Reassembly

8. Remove the CCD Cable, as shown below.

CCD Cable

Core

7. Release the six hooks securing the Scan Upper to the

Scan Lower and remove it, as shown below.

Scan Upper

Notice: You should connector remove the CCD Cable vertically to avoid the CCD Cable pin damage.

9. Pull up the CCD Shaft and take out the CCDM.

CCDM

CCD Shaft

Scan Lower

Service Manual

5-13

Samsung Electronics

Disassembly and Reassembly

10. Squeeze the spring to release the tension in the Belt and lift from the pulleys, as shown below.

Belt

Spring

12. If necessary, remove the two screws securing the

Scan Motor and remove it, as shown below.

Gear Bracket Ass'y

Scan Motor

11. Remove the three screws securing the Scan Motor

Ass'y and then unplug the connector from the Joint

PBA.

Scan Motor Ass'y

13. To remove the ADF Lower Harness, first unlatch the hooks in the direction of arrow and then Unplug the connector from the Joint PBA, as shown below.

ADF Lower Harness

1

1

2

5-14

Service Manual

Samsung Electronics

Disassembly and Reassembly

14. Unplug the Open Sensor connector from the Joint

PBA.

Open Sensor

16. Remove the two screws securing the Joint PBA and remove it, as shown below.

Joint PBA

15. Unlatch the Open Sensor and remove it, as shown below.

Sensor Lever

Open Sensor

17. The connectors are located, as shown below.

Drawer Main PBA

Motor

In Full

Cover Open

(Joint PBA)

Service Manual

5-15

Samsung Electronics

Disassembly and Reassembly

18. Remove the CCD Holder.

19. Unplug the Harness from the CCD Home Sensor and release the CCD Home Sensor, as shown below.

CCD Home Sensor

Harness

CCD Holder

Caution : Reassembling CCDM

1) When refitting the Scanner Belt and Belt Spring take care to relocate the tension spring as close to the right side of the CCDM as is possible, as shown below.

2) When refitting the Scan Upper Cover take care to ensure that the Cover Open Switch is not trapped.

5-16

Service Manual

Samsung Electronics

Disassembly and Reassembly

5.12 Middle Cover Ass'y

1. Before you remove the Middle Cover Ass'y, you should remove:

- Side Cover Left (Refer to 5.9)

- Platen ass'y (Refer to 5.11)

2. Unplug the three connectors(USB, Speaker, Fan), as shown below.

DC Fan

4. Remove the two screws securing the USB Host PBA and remove it.

Harness

USB Host PBA

USB Host

Speaker

3. Remove the five screws securing the Middle Cover

Ass'y and then lift the Middle Cover Ass'y, as shown below.

Middle Cover Ass'y

5. Remove the one screw securing the Speaker and then release the Speaker, as shown below.

Speaker

Service Manual

5-17

Samsung Electronics

Disassembly and Reassembly

6. If necessary, apply light pressure to the both side of the Jam Cover and pull it in the direction of arrow, as shown below.

Jam Cover

7. Pull the DC Fan from the Middle Cover Ass'y, as shown below.

DC Fan

5-18

Service Manual

Samsung Electronics

Disassembly and Reassembly

5.13 Fuser Ass'y

1. Before you remove the Fuser Ass'y, you should remove:

- Rear Cover (Refer to 5.7)

- Side Cover Left, Right (Refer to 5.9)

- Middle Cover Ass'y (Refer to 5.12)

2. Remove the four screws securing the Fuser Ass'y, as shown below.

4. To remove the Thermostat, first release the Link1

Harness below the both side of the Thermostat and then remove the two screws securing the Thermostat and remove it, as shown below.

Link1 Harness

Link1 Harness

Thermostat

5. Remove the one screw securing the Thermistor and release it, as shown below.

3. To remove the Fuser Ass'y, first pull the Holder in the direction of arrow and then take out the Fuser Ass'y, as shown below.

Fuser Ass'y

2

1

Holder

Thermistor

Service Manual

5-19

Samsung Electronics

Disassembly and Reassembly

6. For easy disassembly, release the Link1 Harness and

Link2 Harness, as shown below.

Link1 Harness

Link1 Harness

Link2 Harness

7. Remove the two screws securing the Upper Frame part and then separate the Lower Frame part in the direction of arrow, as shown below.

3

Upper Frame Part

1

Lower Frame Part

2

9. Take out the Halogen Lamp in the direction of arrow and then release the Heat Roller, as shown below.

Ground Spring

Halogen Lamp

Bearing, L

2

Bearing, R

Fuser Gear

Heat Roller

2

Upper Frame

1

Notice: Be careful not to damage or contaminate the surface of the roller when assembling and disassembling the Heat Roller.

10. Release the Pressure Shaft Roller and Pressure

Roller in the direction of arrow, as shown below.

Lower Frame

Bush 2PR, L

Pressure Shaft Roller

Bush 2PR, R

Notice: Be careful especially not to damage the covering of the Fuser Ass'y (If the cover is damaged, it could cause an electric leakage)

8. Remove the two screws securing the Release

Lever(L, R) below the both side of the Halogen Lamp and then remove the Release Lever(L,R) in the direction of arrow.

Release Lever, L

Pressure Roller

Release Lever, R

5-20

Service Manual

Samsung Electronics

Disassembly and Reassembly

5.14 HVPS

1. Before you remove the HVPS, you should remove:

- Side Cover Left (Refer to 5.8)

2. Remove the six screws securing the HVPS and then unplug the all connectors, as shown below.

Notice: Be aware of the Terminals(TR, S) to ensure they are not lost.

Terminal TR

Terminal S

HVPS

Samsung Electronics

Service Manual

5-21

Disassembly and Reassembly

5.15 LIU Unit

1. Before you remove the LIU Unit, you should remove:

- Side Cover Right (Refer to 5.9)

- Harness Guide (Refer to 5.11.3)

2. Unplug the Film Cable from the LIU PBA.

4. If necessary, remove the LIU PBA from the

Supporters, as shown below.

Supporter

Sheet LIU

LIU PBA

Film Cable

3. Remove the three screws securing the LIU Unit and remove it, as shown below.

LIU Unit

5-22

Service Manual

Samsung Electronics

Disassembly and Reassembly

5.16 Shield Main Lower (with Main PBA)

1. Before you remove the Shield Main Lower(with Main

PBA), you should remove:

- LIU Unit (Refer to 5.15)

2. Unplug the all connectors from the Main PBA.

4. If necnsary, remove the four screws securing the Main

PBA and remove it, as shown below.

Shield Main Lower

Main PBA

5. The connectors are located, as shown below.

3. Remove the five screws securing the Shield Main

Lower(with Main PBA) and remove it.

Samsung Electronics

Shield Main Lower

(with Main PBA)

Service Manual

5-23

Disassembly and Reassembly

5.17 Main Drive Ass'y

1. Before you remove the Main Drive Ass'y, you should remove:

- LIU Unit (Refer to 5.15)

- Shield Main Lower(with Main PBA) (Refer to 5.16)

2. Release the Harness and Cable from the Cable

Clamp, as shown below.

3. Remove the nine screws securing the Main Drive

Ass'y and remove it, as shown below.

Cable Clamp

Main Drive Ass'y

Notice: The eight screws have numbers stamped into the Main Drive Ass'y base plate.

When refitting the Main Drive Ass'y tighten the screws the order they are numbered.

5-24

Service Manual

Samsung Electronics

Disassembly and Reassembly

5.18 SMPS

1. Before you remove the SMPS, you should remove:

- Side Cover Right (Refer to 5.9)

2. Unplug the all connectors(Main PBA, Inlet, Fuser_AC) from the SMPS, as shown below.

4. If necessary, first remove the Shield Main Lower

(refer to 5.16) and Main Drive Ass'y (refer to 5.17) and then remove the one screw securing the Shield SMPS and remove it in the direction of arrow.

Main

Inlet,

Fuser_AC

3. Remove the four screws securing the SMPS and remove it.

Shield SMPS

SMPS

Service Manual

5-25

Samsung Electronics

Disassembly and Reassembly

5.19 Regi Roller

1. Before you remove the Regi Roller, you should remove:

- HVPS (Refer to 5.14)

- LIU Unit (Refer to 5.15)

- Shield Main Lower(with Main PBA) (Refer to 5.16)

- Main Drive Ass'y (Refer to 5.17)

2. First remove the Plan Washer securing the Regi

Clutch and then pull the Regi Clutch, as shown below.

4. Take off the Sheet and then remove the Regi Pulley, as shown below.

Sheet

Regi Pulley

3. Remove the E-ring below the both side of the Regi

Roller, as shown below.

Clutch

Plain Washer

5. To remove the Regi Roller, first slide the left side to right side and then take out the left side, as shown below.

Regi Roller

2

Bush

Paper Guide 1

E-ring

Regi Roller

E-ring

Regi Roller

5-26

Service Manual

Notice : Do not grab the rubber part of the Regi Roller, it may cause a malfunction due to a foreigen object.

Samsung Electronics

6. Pull the Feed Idle Shaft.

Feed Idle Shaft

Disassembly and Reassembly

Samsung Electronics

Service Manual

5-27

Disassembly and Reassembly

5.20 Feed Roller

1. Before you remove the Feed Roller, you should remove:

- HVPS (Refer to 5.14)

2. Remove the Feed Pulley and Belt, as shown below.

4. To remove the Feed Roller, first pull the Feed Roller from the Bush and then take out the Feed Roller and

Feed Shaft, as shown below.

Feed Pully

Belt

Feed Shaft

2

Bush

1

Feed Roller

3. Remove the Feed Gear and then remove the E-ring from the Feed Shaft, as shown below.

Notice : Do not grab the rubber part of the Feed Roller, it may cause a malfunction due to a foreigen object.

Feed Gear

Notice: Be aware of the E-ring and Spring to ensure they are not lost.

5-28

Service Manual

Samsung Electronics

Disassembly and Reassembly

5.21 Pick Up Roller

1. Before you remove the Pick Up Roller, you should remove:

- HVPS (Refer to 5.14)

- LIU Unit (Refer to 5.15)

- Shield Main Lower(with Main PBA) (Refer to 5.16)

- Main Drive Ass'y (Refer to 5.17)

2. Remove the two screws securing the Bracket and remove it, as shown below.

4. If necessary, remove the two screws securing the Pick

Up Plate and remove it from the Pick Up Guide, as shown below.

Pick Up Plate

Bracket

3. Remove the three screws securing the Pick Up

Plate(with Pick Up Guide) and then release the Pick

Up Plate in the direction of arrow.

PicK Up Plate

(with Pick Up Guide)

Pick Up guide

5. If necnssary, pull the Pad Holder from the Pick Up

Guide, as shown below.

Pad Holder

Notice: 1) Be aware of the Springs to ensure they are not lost.

2) Clean the surface of the Rubber Pad with ethylalcohol.After wiping, be sure to dry it.

Service Manual

5-29

Samsung Electronics

Disassembly and Reassembly

6. To remove the Pick Up Gear Unit, first unlatch the lock device of the Pick Up Gear Unit, as shown below and then pull the Pick Up Gear Unit in the direction of arrow.

8. When if only remove the Pick Up Rubber, first pull the

Pick Up Rubber(with Housing U) from the Housing B in the direction of arrow and then release the Pick Up

Rubber from the Housing U, as shown below.

1

Housing B

2

1

Pick Up Gear Unit

7. To remove the Pick Up Roller Unit, first lift the notch attached to the right side Pick Up Cam so that it's slide the right to left from the Pick Up Shaft, and then slide the Pick Up Roller Unit left side to right side and take out the left side, as shown below.

2

Rubber

Housing U

9. Remove the one screw securing the Pick Up Solenoid and remove it.

Pick Up Solenoid

2

3

1

Pick Up Roller Unit

Cam

5-30

Service Manual

Samsung Electronics

10. Remove the one screw securing the Cam Holder and remove it.

Disassembly and Reassembly

Cam Holder

Samsung Electronics

Service Manual

5-31

Disassembly and Reassembly

5.22 Exit Roller Unit

1. Before you remove the Exit Roller Unit, you should remove:

- Middle Cover Ass'y (Refer to 5.12)

2. Remove the four screws and two nuts securing the

Fuser Terminal Unit and remove it, as shown below.

Fuser Terminal Unit

4. Remove the three screws securing the Exit Roller

Unit.

3. For easy disassembly, remove the one screw securing the Exit Sensor and remove it.

Exit Sensor

5. First unlatch the lock device below the both side of the

Exit Frame using a flat-blade screwdriver and then pull the Exit Roller Unit, as shown below.

Exit Roller Unit

Lock Device

5-32

Service Manual

Samsung Electronics

6. Remove the Holder Bearing(with Roller Exit F/Down) from the both side of the Exit Frame, as shown below and then remove the Roller Exit Main and Holder Exit

F/Down.

Holder Bearing

Exit Roller

Roller Exit Main

Holder Exit F/Down

Exit Gear

1

2

1

Disassembly and Reassembly

Samsung Electronics

Service Manual

5-33

Disassembly and Reassembly

5.23 LSU

1. Before you remove the LSU, you should remove:

- OPC DEV Unit (Refer to 5.4)

- ITB Unit (Refer to 5.5)

- Middle Cover Ass'y (Refer to 5.12)

2. Apply light pressure to the right side of the LSU Cover

Unit and remove it in the direction of arrow.

3. Unplug the two connectors and then remove the four screws securing the LSU and remove it in the direction of arrow.

LSU

LSU Cover

5.24 MP Unit

1. Before you remove the MP Unit, you should remove:

- Cassette Unit (Refer to 5.3.1)

2. Down the MP Unit, as shown below.

3. Apply light pressure to the both side of the MP Unit and pull it in the direction of arrow, as shown below.

5-34

Service Manual

MP Unit

1

2

Samsung Electronics

6

6. Alignment and Adjustments

This chapter describes some of the main service procedures including:

Using the Tech mode; Clearing paper jam and test patterns.

Much of this chapter is also included in the user's guide.

6.1 Control Panel

6.1.1 CLX-3160FN

Alignment and Adjustmens

1

Speed buttons: Allows you to store frequentlydialed fax numbers and enter them with the touch of a few buttons.

2

Shift: Allows you to shift the speed buttons to access numbers 16 through 30.

3

Phone Book: Allows you to store frequently used fax numbers in memory or search for stored fax numbers. Also allows you to print an Phone Book list.

4

Resolution: Adjusts the document resolution for the current fax job.

5

Redial/Pause: In Standby mode, redials the last number, or in Edit mode, inserts a pause into a fax number.

6

Fax: Activates Fax mode.

7

Copy: Activates Copy mode.

8

Scan: Activates Scan mode.

9

Display: Shows the current status and prompts during an operation.

10

Menu: Enters Menu mode and scrolls through the available menus.

11

Scroll buttons: Scroll through the options available in the selected menu, and increase or decrease values.

12

OK: Confirms the selection on the screen.

13 Back: Sends you back to the upper menu level.

14

Status: Shows the status of your machine.

15 Darkness: Adjusts the document brightness for the current copy job.

16 Original Type: Selects the document type for the current copy job.

17 Reduce/Enlarge: Makes a copy smaller or larger than the original.

18

USB Print: Allows you to directly print files stored on a USB Memory device when it is inserted into the USB memory port on the front of your machine.

19 Number keypad: dials a number or enters alphanumeric characters.

20 On Hook Dial: Engages the telephone line.

21

Stop/Clear: Stops an operation at any time. In

Standby mode, clears/cancels the copy options, such as the darkness, the document type setting, the copy size, and the number of copies.

22

Color Start: Starts a job in Color mode.

23 Black Start: Starts a job in Black and White mode.

Service Manual

6-1

Samsung Electronics

Alignment and Adjustmens

6.1.2 CLX-3160N

1

Copy: Activates Copy mode.

2

Scan: Activates Scan mode.

3

Display: Shows the current status and prompts during an operation.

4

Menu: Enters Menu mode and scrolls through the available menus.

5

Scroll buttons: Scroll through the options available in the selected menu, and increase or decrease values.

6

OK: Confirms the selection on the screen.

7

Back: Sends you back to the upper menu level.

8

Status: Shows the status of your machine.

9

Darkness: Adjusts the document brightness for the current copy job.

10 Original Type: Selects the document type for the current copy job.

11

Reduce/Enlarge: Makes a copy smaller or larger than the original.

12

USB Print: Allows you to directly print files stored on a USB Memory device when it is inserted into the USB memory port on the front of your machine.

13 Number keypad: Dials a number or enters alphanumeric characters.

14

Stop/Clear: Stops an operation at any time. In

Standby mode, clears/cancels the copy options, such as the resolution, the document type setting, the copy size, and the number of copies.

15 Color Start: Starts a job in Color mode.

16 Black Start: Starts a job in Black and White mode.

6-2

Service Manual

Samsung Electronics

Alignment and Adjustmens

6.2 LED Function

The Status LED on the control panel shows the status of your machine.

See the table below to know your machine's status.

Status” LED

Off

Green

Red

On

Blink

On

Blink

Description

The machine is off-line.

The machine is in Power Save mode. When data is received, or any button is pressed, it switches to on-line automatically.

The machine is on-line and can be used.

When the backlight slowly blinks, the machine is receiving data from the computer.

When the backlight fast blinks, the machine is printing data.

The toner cartridge is totally exhausted. Remove the old toner cartridge and install a new one.

Apaper jam has occurred. To solve the problem.

The front cover is open. Close the front cover.

There is no paper in the tray. Load paper in the tray.

The machine has stopped due to a major error. Check the display message.

Aminor error occurs and the machine is waiting an error to be cleared.

Check the display message. When the problem is cleared, the machine resumes.

The toner cartridge is low. Order a new toner cartridge. You can temporarily improve print quality by redistributing the toner.

Samsung Electronics

Service Manual

6-3

Alignment and Adjustmens

6.3 Jam Removal

6.3.1 Clearing document jams

When an original jams while passing through the ADF, Document Jam appears on the display.

1. Remove any remaining pages from the ADF.

2. Open the ADF cover.

4. Close the ADF cover. Then load the removed pages, if any, back into the ADF.

3. Pull the jammed paper gently out of the ADF.

6-4

Service Manual

Samsung Electronics

Alignment and Adjustmens

6.3.1.1 Exit misfeed

1. Open the scanner lid.

2. Turn the release knob to the direction as shown to remove the misfed paper from the document output tray.

6.3.1.2 Roller misfeed

1. Open the scanner lid.

2. Seize the misfed paper, and remove the paper from the feed area by carefully pulling it to the right using both hands.

3. Close the scanner lid. Then load the removed pages back into the ADF.

3. Close the scanner lid. Then load the removed pages back into the ADF.

Service Manual

6-5

Samsung Electronics

Alignment and Adjustmens

6.3.2 Clearing paper jams

When a paper jam occurs, Paper Jam appears on the display. Refer to the table below to locate and clear the paper jam.

6.3.2.1 In the tray 1

1. Open and close the front cover. The jammed paper is automatically ejected from the machine.

If the paper does not exit, go to the next step.

2. Pull the tray 1 open.

3. Remove the jammed paper by gently pulling it straight out.

6-6

Service Manual

If the paper does not move when you pull, or if you do not see the paper in this area, check the paper exit area.

4. Insert the tray 1 into the machine until it snaps into place. Printing automatically resumes.

Samsung Electronics

6.3.2.2 In the optional tray 2

1. Pull the optional tray 2 open.

Alignment and Adjustmens

3. Open the jam cover in the optional tray 2.

2. Remove the jammed paper from the machine.

4. Pull the jammed paper out in the direction shown.

If the paper does not move when you pull, or if you do not see the paper in this area, go to the next step.

Samsung Electronics

5. Close the jam cover. Printing automatically resumes.

Service Manual

6-7

Alignment and Adjustmens

6.3.2.3 In the mamual tray

1. Pull the tray 1 out.

2. Push the manual tray tab down.

6.3.2.4 In the paper exit area

1. Open and close the front cover. The jammed paper is automatically ejected from the machine.

2. Gently pull the paper out of the output tray.

3. Pull the Jammed paper out of the manual tray.

If you do not see the jammed paper or if there is any resistance when you pull, stop and go to the next step.

3. Open the rear cover.

4. If you see the jammed paper, pull it straight up.

Skip to step 8.

4. Insert the tray 1 into the machine until it snaps into place. Printing automatically resumes.

6-8

Service Manual

If you still do not see the paper, go to the next step.

Samsung Electronics

5. Open the fuser door.

Alignment and Adjustmens

6. Locate the jammed paper and pull it out.

Samsung Electronics

Service Manual

6-9

Alignment and Adjustmens

6.4 System setup

6.4.1 Menu overview

The control panel provides access to various menus to set up the machine or use the machine's functions.

These menus can be accessed by pressing Menu. Refer to the following diagram. Menus available in

Fax, Copy, or Scan mode vary.

6.4.2 Changing the display language

To change the language that appears on the control panel, follow these steps:

1. Press Menu until System Setup appears on the bottom line of the display and press OK.

2. Press OK when Machine Setup appears.

3. Press the Scroll buttons until Language appears and press OK.

4. Press the Scroll buttons until the language you want appears and press OK.

5. Press Stop/Clear to return to Standby mode.

6-10

Service Manual

Samsung Electronics

Alignment and Adjustmens

6.4.3 Setting the date and time

The current date and time are shown on the display when your machine is on and ready to work. For the

CLX-3160FN, all of your faxes will have the date and time printed on them.

Note : If power to the machine is cut off, you need to reset the correct time and date once the power has been restored.

1. Press Menu until System Setup appears on the bottom line of the display and press OK.

2. Press OK when Machine Setup appears.

3. Press the Scroll buttons until Date & Time appears and press OK.

4. Enter the correct time and date using the number keypad.

Month = 01 to 12

Day = 01 to 31

Year = requires four digits

Hour = 01 to 12 (12-hour mode)

00 to 23 (24-hour mode)

Minute = 00 to 59

Note : The date format may differ from country to country

You can also use the Scroll buttons to move the cursor under the digit you want to correct and enter a new number.

5. To select AM or PM for 12-hour format, press the or # button or any number button.

When the cursor is not under the AM or PM indicator, pressing the or # button immediately moves the cursor to the indicator.

You can change the clock mode to 24-hour format (e.g. 01:00 PM as 13:00). For details, see the next section.

6. Press OK to save the time and date.

When you enter a wrong number, Out of Range appears and the machine does not proceed to the next step. If this happens, simply reenter the correct number.

7. Press Stop/Clear to return to Standby mode.

Changing the clock mode

You can set your machine to display the current time using either a 12-hour or 24-hour format.

1. Press Menu until System Setup appears on the bottom line of the display and press OK.

2. Press OK when Machine Setup appears.

3. Press the Scroll buttons until Clock Mode appears and press OK.

4. Press the Scroll buttons to select the other mode and press OK.

5. Press Stop/Clear to return to Standby mode.

Service Manual

6-11

Samsung Electronics

Alignment and Adjustmens

6.4.4 Changing the default mode (CLX-3160FN only)

Your machine is preset to Fax mode. You can switch this default mode between Fax mode and Copy mode.

1. Press Menu until System Setup appears on the bottom line of the display and press OK.

2. Press OK when Machine Setup appears.

3. Press the Scroll buttons until Default Mode appears and press OK.

4. Press the Scroll buttons until the default mode you want appears and press OK.

5. Press Stop/Clear to return to Standby mode.

6.4.5 Setting sounds

You can control the following sounds:

Key Sound: Turns the key sound on or off. With this option set to On, a tone sounds each time a key is pressed.

Alarm Sound: Turns the alarm sound on or off. With this option set to On, an alarm tone sounds when an error occurs or fax communication ends.

Speaker (CLX-3160FN only): Turns on or off the sounds from the telephone line through the speaker, such as a dial tone or a fax tone.

With this option set to Comm. which means "Common," the speaker is on until the remote machine answers.

You can adjust the volume level using On Hook Dial.

Ringer (CLX-3160FN only): Adjusts the ringer volume. For the ringer volume, you can select Off, Low,

Mid, and High.

Speaker, ringer, key sound, and alarm sound

1. Press Menu until System Setup appears on the bottom line of the display and press OK.

2. Press the Scroll buttons until Sound/Volume appears and press OK.

3. Press the Scroll buttons until the sound option you want appears and press OK.

4. Press the Scroll buttons until the desired status or volume for the sound you have selected appears and press OK.

5. If necessary, repeat steps 3 through 5 to set other sounds.

6. Press Stop/Clear to return to Standby mode.

Speaker volume

1. Press On Hook Dial. Adial tone sounds from the speaker.

2. Press the Scroll buttons until you hear the volume you want.

3. Press On Hook Dial to save the change and return to Standby mode.

Note : You can adjust the speaker volume only when the telephone line is connected.

6-12

Service Manual

Samsung Electronics

Alignment and Adjustmens

6.4.6 Entering characters using the number keypad

As you perform various tasks, you may need to enter names and numbers. For example, when you set up your machine, you enter your name or your company's name, and the fax number. When you store fax numbers in memory, you may also enter the corresponding names.

Entering alphanumeric characters

1. When you are prompted to enter a letter, locate the button labeled with the character you want. Press the button until the correct letter appears on the display.

For example, to enter the letter O, press 6, labeled with MNO.

Each time you press 6, the display shows a different letter, M, N, O, and finally 6.

You can enter special characters, such as space, plus sign, and etc. For details, see the below section.

2. To enter additional letters, repeat step 1.

If the next letter is printed on the same button, move the cursor by pressing the right Scroll button and then press the button labeled with the letter you want. The cursor will move to the right and the next letter will appear on the display.

You can enter a space by pressing 1 twice.

3. When you have finished entering letters, press OK.

Keypad letters and numbers

Correcting numbers or names

If you make a mistake while entering a number or name, press the left Scroll button to delete the last digit or character. Then enter the correct number or character.

Service Manual

6-13

Samsung Electronics

Alignment and Adjustmens

Inserting a pause

With some telephone systems, you must dial an access code (9, for example) and listen for a second dial tone. In such cases, you must insert a pause in the telephone number. You can insert a pause while you are setting up speed buttons or speed dial numbers.

To insert a pause, press Redial/Pause at the appropriate place while entering the telephone number.

A- appears on the display at the corresponding location.

6.4.7 Using the save modes

Power Save mode

Power Save mode allows your machine to reduce power consumption when it is not in actual use. You can turn this mode on and select a length of time for which the machine waits after a job is printed before it switches to a reduced power state.

1. Press Menu until System Setup appears on the bottom line of the display and press OK.

2. Press OK when Machine Setup appears.

3. Press the Scroll buttons until Power Save appears and press OK.

4. Press the Scroll buttons until On appears and press OK.

5. Press the Scroll buttons until the time setting you want appears and press OK.

6. Press Stop/Clear to return to Standby mode.

Scan Power Save mode

Scan Power Save mode allows you to save power by turning off the scan lamp. The scan lamp under the scanner glass automatically turns off when it is not in actual use to reduce power consumption and extend the life of the lamp. The lamp automatically wakes up after some warm-up time when you start scanning.

You can set the length of time for which the scan lamp waits after a scan job is completed before it switches to the power save mode.

1. Press Menu until System Setup appears on the bottom line of the display and press OK.

2. Press OK when Machine Setup appears.

3. Press the Scroll buttons until Scan PWR Save appears and press OK.

4. Press the Scroll buttons until the time setting you want appears and press OK.

5. Press Stop/Clear to return to Standby mode.

6-14

Service Manual

Samsung Electronics

Alignment and Adjustmens

6.4.8 Setting print job timeout

You can set the amount of time a single print job is active before it must print.

The machine handles incoming data as a single job if it comes in within the specified time. When an error occurs while processing data from the computer and the data flow stops, the machine waits the specified time and then cancels printing if data flow does not resume.

1. Press Menu until System Setup appears on the bottom line of the display and press OK.

2. Press OK when Machine Setup appears.

3. Press the Scroll buttons until Job Timeout appears and press OK.

4. Press the Scroll buttons until the time setting you want appears and press OK.

5. Press Stop/Clear to return to Standby mode.

Samsung Electronics

Service Manual

6-15

Alignment and Adjustmens

6.5 Network setup

This chapter gives you step-by-step instructions for setting up your machine for network connections.

This chapter includes:

Introduction

Supported operating systems

Configuring TCP/IP

Setting Ethernet speed

Restoring the network configuration

Printing a network configuration page

6.5.1 Introduction

Once you have connected your machine to a network with an RJ-45 Ethernet cable, you can share the machine with other network users.

You need to set up the network protocols on the machine to use it as your network printer. Protocols can be set up by the following two methods:

Via network administration programs

You can configure your machine's print server settings and manage the machine via the following programs that came with your machine:

SyncThru TM Web Admin Service: A web-based printer management solution for network administrators.

SyncThru

TM

Web Admin Service provides you with an efficient way of managing network devices and lets you remotely monitor and troubleshoot network printers from any site with corporate intranet access.

SyncThru TM Web Service: Aweb server embedded to your network print server, which allows you to:

- Configure the network parameters necessary for the machine to connect to various network environments.

- Customize printer, copy, and fax settings.

SetIP: Autility program allowing you to select a network interface and manually configure the addresses for use with the TCP/IP protocol.

For further details, refer to the user's guide on the network utilities CD that came with your machine.

Via the control panel

You can set up the following basic network parameters through the machine's control panel:

Configure TCP/IP

Configure EtherTalk

6-16

Service Manual

Samsung Electronics

6.5.2 Supported operating systems

The following table shows the network environments supported by the machine:

Alignment and Adjustmens

TCP/IP: Transmission Control Protocol/Internet Protocol

IPP: Internet Printing Protocol

SNMP: Simple Network Management Protocol

DHCP: Dynamic Host Configuration Protocol

BOOTP: Bootstrap Protocol

6.5.3 Configuring TCP/IP

Your machine can be set up with a variety of TCP/IP network information, such as an IP address, a subnet mask, a gateway, and DNS addresses.

There are several ways in which your machine can be assigned a TCP/IP address, depending on your network.

Static addressing: ATCP/IP address is assigned manually by the system administrator.

Dynamic addressing via BOOTP/DHCP (default): ATCP/IP address is assigned automatically by the server.

Note : Before configuring TCP/IP, you need to set the network protocol to TCP/IP.

Static addressing

To enter a TCP/IP address from your machine's control panel, take the following steps:

1. Press Menu until Network appears on the bottom line of the display and press OK.

2. Press OK when TCP/IP appears.

3. Press the Scroll buttons until Static appears and press OK.

4. Press OK when IP Address appears.

5. Enter a byte between 0 and 255 using the number keypad and press the Scroll buttons to move between bytes.

Repeat this to complete the address from the 1st byte to the 4th byte.

6. When you have finished, press OK.

7. Repeat steps 5 and 6 to configure the other TCP/IP parameters: subnet mask and gateway address.

8. Press the Scroll buttons until Primary DNS appears and press OK.

Service Manual

6-17

Samsung Electronics

Alignment and Adjustmens

9. Enter each byte of the address and press OK.

10. Press the Scroll buttons until Secondary DNS appears and press OK.

11. Enter each byte of the address and press OK.

12. Press Stop/Clear to return to Standby mode.

Dynamic addressing (BOOTP/DHCP)

To have a TCP/IP address assigned automatically by the server, take the following steps:

1. Press Menu until Network appears on the bottom line of the display.

2. Press OK when TCP/IP appears.

3. Press the Scroll buttons until DHCP or BOOTP appears and press OK.

4. Press Stop/Clear to return to Standby mode.

6.5.4 Setting Ethernet speed

You can select the communication speed for Ethernet connections.

1. Press Menu until Network appears on the bottom line of the display and press OK.

2. Press the Scroll buttons until Ethernet Speed appears and press OK.

3. Press the Scroll buttons until the speed you want appears and press OK.

4. Press Stop/Clear to return to Standby mode.

6-18

Service Manual

Samsung Electronics

Alignment and Adjustmens

6.5.5 Restoring the network configuration

You can return the network configuration to its default settings.

1. Press Menu until Network appears on the bottom line of the display and press OK.

2. Press the Scroll buttons until Clear Setting appears and press OK.

3. Press OK when Yes appears to restore the network configuration.

4. Power the machine off and back on.

6.5.6 Printing a network configuration page

The Network Configuration page shows how the network interface card on your machine is configured.

1. Press Menu until Network appears on the bottom line of the display and press OK.

2. Press the Scroll buttons until Network Info appears and press OK.

3. Press OK when Yes appears.

The Network Configuration page prints out.

Service Manual

6-19

Samsung Electronics

Alignment and Adjustmens

6.6 Sample Pattern

This product provides several printable test patterns for maintenance purposes. These patterns can be used to aid the diagnosis of print quality problems.

6.6.1 Printing a report

[Printing a Document in Windows]

1. Click the Windows Start menu.

2. For Windows 98/Me/NT 4.0/2000, select Settings and then Printers.

For Windows XP, select Printers and Faxes.

3. Select the Samsung MFP CLX-3160 Series printer.

4. Click the right mouse button on the printer icon and:

For Windows 98/Me, select Properties.

For Windows 2000/XP, select Printing Preferences.

For Windows NT 4.0, select Document Default.

5. Change the settings on each tab and click OK.

6. Now “PRINTING”

6-20

Service Manual

Samsung Electronics

Alignment and Adjustmens

6.6.2 Printing a Configuration Page

You can print a configuration page from the printer’s control panel. Use the configuration page to view the current settings, to help troubleshoot problems.

To print a configuration page: In ready mode, press and hold the Stop button on the control panel for 5 seconds.

Aconfiguration page prints out.

Samsung Electronics

Service Manual

6-21

Alignment and Adjustmens

6.7 Periodic Defective Image

If an image defects appears at regular intervals on the printed-paper, it is due to a faulty or damaged roller.

Refer to the table below and check the condition of the appropriate roller.

No Roller

1

2

OPC Drum

Charge Roller

3

4

Supply Roller

Developing Roller

5 1

st

Transfer Roller

6 2

nd

Transfer Roller

7 Heat Roller

8 Pressure Roller

Period

188.5 mm

37.7mm

47.5mm

26.0mm

32.7mm

57.5mm

86.6mm

86.6mm

Phenomenon

White and Black Spots

Black Spot and line and Periodic Band

Periodic Band by little difference of density

White Spot, Horizontal black band

Ghost, Damaged Image by abnormal tranfer

Ghost, Damaged Image by abnormal tranfer

Black Spots or Vertical Black Band

Background

6-22

Service Manual

Samsung Electronics

Alignment and Adjustmens

6.8 Tech Mode

6.8.1 How to Enter Tech Mode

In service (tech) mode, the technician can check the machine and perform various test to isolate the cause of a malfunction.

While in Tech mode, the machine still performs all normal operations.

To enter the Tech mode

To enter the Tech mode, press

LCD briefly displays ‘TECH’, the machine has entered service (tech) mode. in sequence, and the

Samsung Electronics

Service Manual

6-23

Alignment and Adjustmens

6.8.2 Setting-up System in Tech Mode

6-24

Service Manual

Samsung Electronics

Alignment and Adjustmens

6.8.3 Data Setup

SEND LEVEL

You can set the level of the transmission signal. Typically, the Tx level should be under -12 dBm.

Caution : The Send Fax Level is set at the best condition in the shipment from factory. Never change settings arbitrarily.

DIAL MODE

This function can choose dial method.

*Default : Dial(Dial/Pulse)

MODEM SPEED

You can set the maximum modem speed.

Communication is done with modem speed automatically set at lower speed when communicating with a slower speed modem since communication is done on the standard of the side where modem speed is low for transmission/reception. It is best set 33.6Kbps as default setting.

ERROR RATE

When the error rate is about exceed the set value, the Baud rate automatically adjusts to 2400 bps.

This ensures that the error rate remains below the set value.

You can select the rate between 5% and 10%.

CLEAR ALL MEMORY

The function resets the system to factory default settings.

This function is used to reset the system to the initial value when the product is functioning abnormally . All the values are returned to the default values, and all the information, which was set by the user, will be erased.

< Method >

1. Select the [MEMORY CLEAR] at the TECH MODE.

2. Push the ENTER button.

3. Select you country. (There are four country groups. Refer to the table below.)

4. Push the ENTER button then it will clear all memory.

NOTICE : Always perform a memory clear after replacing the main board. Otherwise, the system may not operate properly.

Country Group

Country

USA/Canada

USA/Canada

Mexico

Brazil

UK

UK

Germany

France

Italy

Spain

Austria

Netherlands

Belgium

Portugal

Sweden

Norway

Denmark

Finland

Switzerland

Greece

Ireland

Turkey

Russia

Russia

India

Oman

Poland

Bangladesh

Kuwait

Moroco

Algeria

Pakistan

UAE

Bahrain

Srilanka

Saudi Arabia

Chile

Peru

Argentina

Hungary

Romania

Bulgaria

Czech

Southafrica

South Africa

Service Manual

6-25

Samsung Electronics

Alignment and Adjustmens

Flash Upgrade

The Firmware Upgrade function and has two methods, Local and Remote.

1)Local Machine Upgrade

• RCP(Remote Control Panel) mode

This method is for Parallel Port.or USB Port Connect to PC and activate RCP(Remote Control Panel) to upgrade the

Firmware.

< Method >

How to Update Firmware using RCP

1. Connect PC and Printer with Parallel Cable or USB Cable.

2. Execute RCP and select Firmware Update.

3. Search Firmware file to update with Browse Icon.

4. Click Update icon, firmware file is transmitted to Printer automatically and printer is initialized when it finished.

5. Click Refresh icon and check what is updated.

• DOS Command mode

This method is just for Parallel Port. Connect to PC with Parallel cable and enter DOS Command to upgrade the

Firmware

< Method >

1. The first of all, need the files : down.bat, down_com.bin, fprt.exe, and Rom File: file name for upgrade.Save the files in the same folder.

2. In the DOS, input as below and push the enter key. Then, it will be automatically upgraded.

3. There are two commands for the conditions of product.

* When the product is in idle condition down "rom file"

* When the product is in Ready condition (TECH MODE DATA SETUP FLASH UPGRADE LOCAL) copy/b

"rom file" lpt1

4. Do not turn off the power while upgrading process.

2) Remote Upgrade

This is a function that a fax with the latest firmware sends files to a fax in long distance through telephone line.

< Method >

1. Before remote upgrade, the latest firmware should be loaded into the machine.

(TECH MODE DATA SETUP FLASH UPGRADE REMOTE)

2. Input the fax number, which needs to be upgraded. (Several faxes can be upgraded at the same time. In this case, enter the each fax number.)

3. After push the enter button, send the firmware file by calling to the appointed number. (Around 10~15 minutes needs to send the file.)

< Caution >

1. sending and receiving fax must be the same model.

2. Asending fax must be set up as ECM mode, and a receiving memory must be set up as 100%. If not, the function operates abnormally

6-26

Service Manual

Samsung Electronics

Alignment and Adjustmens

S/W of Maintenance

1. Clearing the Memory

You can selectively clear information stored in your machine s memory.

1) Press Menu on the control panel until Maintenance appears on the top line of the display.

2) Press the scroll button (left-key or right-key) until you see Clear Memory on the bottom line and press Enter

- The first available menu item, Clear All Mem. displays on the bottom line.

- See next page - There are some item to display on the LCD.

3) Press the scroll button (left-key or right-key) until you see the item you want to clear.

4) Press Enter. The selected memory is cleared and the display asks you to continue clearing the next item.

5) To clear another item, press Enter and repeat steps 3 and 4

- To return to Standby mode, press Stop/Clear.

- As below item you can selectively clear information stored in your machine s memory.

Clear All Mem.:

- Clears all of the data stored in the memory and resets all of your settings to the factory default.

Paper Setting:

- Restores all of the Paper Setting options to the factory default.

Copy Setup:

- Restores all of the Copy Setup options to the factory default.

Fax Setup:

- Restores all of the Fax Setup options to the factory default.

Fax Feature:

- Cancels all of the scheduled fax jobs in the machine s memory.

- As below item you can selectively clear information stored in your machine s memory.

Advanced Fax:

- Restores all of the Advanced Fax setting options to the factory default.

Sound/Volume:

- Resets the sound and volume settings to the factory default.

Machine Setup:

- Resets all of the system settings, such as the machine ID, date and time, display language and save modes, to the factory default.

Sent Report:

- Clears all of records of your faxes sent.

RCV Report:

- Clears all of records of your faxes received.

Phone Book:

- Clears the one-touch, speed and group dial numbers stored in the memory.

2. Adjust shading

When the scan unit becomes dirty, it can alter the shading value.

If your copy has black lines or is blurred, adjust the shading setting.

1) Load a sheet of white paper into the ADF.

2) Make machine Tech mode.

3) Press Menu on the control panel and scroll until Machine Test displays.

4) Scroll to Shading Test and Enter.

5) Select Shading&Print appears on the bottom line and press Enter.

6) Your machine picks up the paper and adjusts the shading value.

7) After adjusting, shading value will be printed with graphic image.

Service Manual

6-27

Samsung Electronics

Alignment and Adjustmens

3. Flash Upgrade

The Firmware Upgrade function and has two methods, Local and Remote.

3.1 Local Machine

• RCP(Remote Control Panel) mode

This method is for Parallel Port.or USB Port Connect to PC and activate RCP(Remote Control Panel) to upgrade the

Firmware.

< Method >

How to Update Firmware using RCP

1. Connect PC and Printer with Parallel Cable or USB Cable.

2. Execute RCP and select Firmware Update.

3. Search Firmware file to update with Browse Icon.

4. Click Update icon, firmware file is transmitted to Printer automatically and printer is initialized when it finished.

5. Click Refresh icon and check what is updated.

• DOS Command mode

This method is just for Parallel Port. Connect to PC with Parallel cable and enter DOS Command to upgrade the

Firmware

< Method >

1. The first of all, need the files : down.bat, down_com.bin, fprt.exe, and Rom File: file name for upgrade.Save the files in the same folder.

2. In the DOS, input as below and push the enter key. Then, it will be automatically upgraded.

3. There are two commands for the conditions of product.

* When the product is in idle condition down "rom file"

* When the product is in Ready condition (TECH MODE DATA SETUP FLASH UPGRADE LOCAL) copy/b "rom file lpt1

4. Do not turn off the power while upgrading process.

3.2 Remote Upgrade

This is a function that a fax with the latest firmware sends files to a fax in long distance through telephone line.

< Method >

1. Before remote upgrade, the latest firmware should be loaded into the machine.(TECH MODE DATA SETUP

FLASH UPGRADE REMOTE)

2. Input the fax number, which needs to be upgraded. (Several faxes can be upgraded at the same time. In this case, enter the each fax number.)

3. After push the enter button, send the firmware file by calling to the appointed number. (Around 10~15 minutes needs to send the file.)

< Caution >

1. sending and receiving fax must be the same model.

2. Asending fax must be set up as ECM mode, and a receiving memory must be set up as 100%.

If not, the function operates abnormally

6-28

Service Manual

Samsung Electronics

Alignment and Adjustmens

4. Remote Diagnostic System(RDS)

RDS and FT-EGT Automatic Ordering System, will enhance the quality and the speed of after sales service and monitor the performance of the MFP at the customer site.

MFP Should be connected by MFP Server.

4.1 Required components of RDS

RDS for MFP system consists of the following three components that communicate with each other

1. Main RDS Server connected to FAX-MODEM.

2. RDS Client Application.

3. RDS on MFP.

4.2 Enable of RDS on MFP

This value is in Tech Mode.

The factory default for Consumables Status Update / Error Proactive value is Disabled.

< Method >

1. MFP Should be connected by RDS Server.

2. Service numbers should have the proper values.

: TECH MODE DATA SETUP NOTIFY TONER 2.RDS Service Number.

3. Machine Serial No. should have the proper values.

: TECH MODE DATA SETUP NOTIFY TONER 1.Toner Serial No.

4. Criter value input is optional, default is set to 1000-page.

: TECH MODE DATA SETUP NOTIFY TONER 2.RDS Criter.Value.

5. Remote Test should be On

: Maintenance Remote Test On

6. Change the password : if you forgot the Notify Toner password, enter the new password.

: TECH MODE DATA SETUP NOTIFY TONER RDS RDS Password.

7. If you are to enable the RDS system, Notify Toner option should be [Off].

4.3 Call setup & Release

In order to perform any RDS activity on a Customer MFP, the SVC will have to setup a call to it.

On successful completion of call setup, one or more RDS functions can be executed before call release is manually initiated.

When connecting to a device, RDS will query the MFP for serial no. If Serial No. is a zero-length string / invalid string, user will be prompted to enter a valid serial no. for the device. If the user chooses not to enter the serial number at that point, he can enter/edit it later also; Serial number will be configurable just like any other MFP parameter

Following successful connection, following details of the MFP will be displayed :

Tel. No, Model, Server Port (that is connected to), Status, Serial Number, Firmware Version, Engine Version,

Emulation Version

In case the established call is dropped due to an error condition, RDS Client Application will notify the user. It will then be necessary to manually request for another call setup to the desired MFP before any RDS function can be reattempted.

If no activity is detected on a connected call for a maximum duration of 5 minutes (300 seconds), the call will be released / disconnected from the MFP-side.

Service Manual

6-29

Samsung Electronics

Alignment and Adjustmens

6.8.4 Machine Test

SWITCH TEST

Use this feature to test all keys on the operation control panel. The result is displayed on the LCD window each time you press a key.

MODEM TEST

Use this feature to hear various transmission signals to the telephone line from the modem and to check the modem. If no transmission signal sound is heard, it means the modem part of the main board malfunctioned.

DRAM TEST

Use this feature to test the machine's DRAM. The result appears in the LCD display.

If all memory is working normally, the LCD shows << O K >>

ROM TEST

Use this feature to test the machine'S ROM. The result and the software version appear in the LCD display.

• FLASH VER : 1.00 V

• ENGINE VER :1.00V

PATTERN TEST

Using this pattern printout, you can check if the printer mechanism is functioning properly.

It is needed in the production progress. Service person doesn't need to use it.

SHADING TEST

The function is to get the optimum scan quality by the specific character of the CCD(Charge

Coupled Device). If the copy image quality is poor, perform this function to check the condition

CCD unit.

< Method >

1. Select the [ADJUST SHADING] at the

TECH MODE.

2. Push the SET UP button then an image will be scanned.

3. After the scan, CCD SHADING PRO-

FILE will be print out.

4. If the printed image is different to the image, the CCD is defect.

NOTICE : When you test CCD, make sure that the cover is closed.

6-30

Service Manual

Samsung Electronics

Alignment and Adjustmens

6.8.5 Report

PROTOCOL LIST

This list shows the sequence of the CCITT group 3 T.30 protocol during the most recent sending or receiving operation. Use this list to check for send and receive errors. If a communication error occurs while the machine is in TECH mode, the protocol list will print automatically.

OTHER ITEM

This list provides a list of the user system data settings and tech mode settings.

Component Check

Samsung Electronics

Service Manual

6-31

Alignment and Adjustmens

6.8.6 Detail Description

Function Name

01.Motor Test

02.Pick Up Test

03.Fan Test

04.Manual Clutch Test

11.LSU Motor

12.LSU Hsync Test

13.LD Test

21.Feed Sen Test

22.Exit Sen Test

23.Cover Sen Test

24.Empty Sen Test

25.Manual Sen Test

31.Them ADC 180

32.Them ADC 140

33.Them ADC 120

34.Them ADC 100

41.MHV Test

42.Dev Bias Test

43.THV EN/NEG Test

44.THV ON(1300V)

45.THV ADC 1300V

46.THV ADC 600V~3500

Description

The main motor keeps running after the execution key is chosen and stops when the stop key is chosen. automatically stops, when the execution is chosen.

The fan keeps running after the execution key is chosen and stops when the stop key is chosen.

The tray2,3 clutch is on for 1sec and then it automatically stops, when the execution is chosen.On this function, the main motor runs before 2sec from the point of the clutch on in order to check the clutch state.

Test The laser motor keeps running after the execution key is chosen and stops when the stop key is chosen.

“Laser Leady” is displayed, When the Laser Scanning

Unit is ready to print. On the other case “Laser Error”

“Diode On” is displayed, when the laser diode is on.

On the other case “Diode Off” is displayed.

These Functions are considered to check the present state (normal or not)of the Sensors.

After the cover is open, touch the sensor and confirm the message changed “Cover Open” to “ Cover Close”

These Functions are considered to check the present state (normal or not)of the Sensors.

“current value"is displayed on the upper line of the panel, and “target value"on the bottom line.

Target value is limited from “191˚C” to “80˚C”

These Functions are considered to check whether the control for HVPS is normal or not.

Display

Main Motor On(Off)

Tray 1,2 Solenoid On/Off

Fan On(Off)

Tray 2,3 Clutch On/Off

Laser Motor On(Off)

Laser Leady On(Off)

Diode On(Off)

"Sensor Off"to “ Sensor On ”

"Cover Open" to "Cover Close"

"Sensor Off"to “ Sensor On ”

Input and output value are

ADC value.(refer to the

ADC table)

MHV On(Off)

Dev Bias On(Off)

THV EN/NEG On(Off)

THV On(Off)

ADC value displayed.

ADC value displayed.

6-32

Service Manual

Samsung Electronics

Alignment and Adjustmens

6.8.7 Identify Sale Date

This function confirms the date that consumer bought product and used the product for the first time.

When the consumer first operate the machine, it will start a scan and page count.

The time the machine was first used is remembered.

These settings are are remembered after memory delete (Clear All Memory).

< Method >

Press MENU, #, 1, 9, 3, # in sequence.Firmware version is displayed on LCD.

Press 1( in the number keypad) : The LCD display shows "Updated date"

Press 2( in the number keypad) : The LCD display shows "Product first use date"

< Display >

OS 1 . 00 . 86 . 07

11-31-2005

Service Data

2004-1-11

Samsung Electronics

Service Manual

6-33

Alignment and Adjustmens

6.9 Error Message

Messages in the colored cells are available only with CLX-3160FN.

Display

[Color] Toner Empty

[Color] Toner Low

Meaning

The color toner cartridge has run out. The machine stops printing.

The corresponding color toner cartridge is almost empty.

[COMM. Error]

Suggested solutions

Replace the color toner cartridge with a new one.

Take out the toner cartridge and thoroughly shake it. By doing this, you can tem porarily reestablish printing operations.

Ask the sender to try again.

[Incompatible]

[Line Error]

[No Answer]

[No Paper] Add Paper

[Stop Pressed]

ADC Not Confirm Error

Cancel?

1:Yes 2:No

Deve Home Sensor Error

There is a problem in the fuser unit.

Document Jam

Door Open

Enter Again

Fuser Fan Locked

Group Not Available

The machine has a communication problem.

The remote machine does not have the requested feature, such as polling.

This message also occurs if the remote machine does not have enough memory space to complete the operation you are attempting.

Your machine cannot connect with the receiving fax machine or has lost contact because of a problem with the phone line.

The receiving fax machine has not answered after several redial attempts.

The paper in the tray has run out.

Stop/Clear has been pressed during an operation.

Aproblem has occurred in the ADC in the machine.

Your machine's memory has become full while trying to store an original into mem ory.

The loaded original has jammed in the

ADF.

The front cover or rear cover is not securely latched.

You entered an unavailable item.

There is a problem in the cooling fan of the machine.

You have tried to select a group location number where only a single location number can be used, such as when adding locations for a Multiple Send operation.

Reconfirm the remote machine's features.

Try again. If the problem persists, wait an hour or so for the line to clear and try again. Or, turn the ECM mode on.

Try again. Make sure that the receiving machine is operational.

Load paper in the tray.

Try again.

Replace to the Main board.

To cancel the fax job, press the 1 button to accept Yes. If you want to send those pages that have been successfully stored, press the 2 button to accept No. You should send the remaining pages later, when memory is available.

Unplug the power cord and plug it back in.

If the problem persists, Replace to the

Main board.

Clear the jam.

Close the cover until it locks into place.

Enter the correct item again.

Open and then close the front cover.

Use a speed dial number or dial a number manually using the number keypad.

6-34

Service Manual

Samsung Electronics

Alignment and Adjustmens

Display

Install [Color] Toner

Install [Part]

Invalid [Color] Toner

Invalid [Part]

Line Busy

Low Heat Error Cycle

Power

LSU Hsync Error Cycle

Power

LSU Motor Error Cycle

Power

Main Motor Locked

Memory Dial Full

Memory Full

MP Tray Paper Empty

Not Assigned

Open Heat Error

Cycle Power

Operation Not Assigned

Out Bin Full

Paper Jam 0

Open/Close Door

Paper Jam 1

Open/Close Door

Power Failure

Meaning

The color toner cartridge is not installed.

The corresponding part of the machine is not installed.

The color toner cartridge you have installed is not for your machine.

The color part of the machine is not for your machine.

The receiving fax machine did not answer or the line is already engaged.

There is a problem in the fuser unit.

Suggested solutions

Install the color toner cartridge.

Install the part into your machine.

Install the a Samsung-genuine color toner cartridge designed for your machine.

Install the a Samsung-genuine part designed for your machine.

Try again after a few minutes.

Aproblem has occurred in the LSU (Laser

Scanning Unit).

Aproblem has occurred in the LSU (Laser

Scanning Unit).

There is a problem in the main motor.

You are trying to schedule a fax job when memory for storing fax jobs is full.

The memory is full.

Unplug the power cord and plug it back in.

If the problem persists, Replace to the

Toner Cartridge.

Unplug the power cord and plug it back in.

If the problem persists, Replace to the

Toner Cartridge.

Unplug the power cord and plug it back in.

If the problem persists, Replace to the

LSU Unit.

Open and then close the front cover.

Wait until a scheduled job is complete.

Delete unnecessary fax jobs and retransmit after more memory becomes available.

Alternatively, split the transmission into more than one operation.

Load paper in the multi-purpose tray.

There is no paper in the multi-purpose tray.

The speed button or speed dial number you tried to use has no number assigned to it.

There is a problem in the fuser unit.

You are in the Add Page/Cancel Job operation, but there are no jobs stored.

The output tray of the machine is full of paper.

Paper has jammed in the feeding area of the tray.

Paper has jammed in the paper exit area.

Enter the number manually using the number keypad or store the number or address.

Unplug the power cord and plug it back in.

If the problem persists, Replace to the

Fuser Unit.

Check the display to see if there are any scheduled jobs.

Remove paper.

Clear the jam.

Clear the jam.

Power has turned off then on and the machine's memory has not been back up.

The job which you were trying to do before the power failure must be completely re-done.

Service Manual

6-35

Samsung Electronics

Alignment and Adjustmens

Display

Replace [Color]

Toner

Replace [Part]

Replace [Part]

Soon

Retry Redial?

Scanner locked

SCF Cover Open

SCF Paper Jam

Self Diagnostic...

Transfer Belt Error

Tray 1

Paper Empty

Tray 2

Paper Empty

Meaning

This message appears between Toner

Empty and Toner Low status.

The life of the part expires totally.

Suggested solutions

Replace the toner cartridge with a new one.

Replace the part with a new one. Call for service.

Replace to maintenance part.

The life of the part expires soon.

The machine is waiting for a specified time interval to redial a previously busy station.

The scanner module is locked

The jam cover in the optional tray 2 is open.

Paper has jammed in the optional tray 2.

The engine in your machine is checking some problems detected.

Aproblem has occurred in the transfer belt in the machine.

There is no paper in the tray 1.

You can press OK to immediately redial, or

Stop/Clear to cancel the redial operation.

Unlock the scanner and press Stop/Clear.

Close the jam cover in the optional tray 2.

Clear the jam.

Please wait a few minutes.

Unplug the power cord and plug it back in.

If the problem persists, please call for service.

Load paper in the tray 1.

There is no paper in the optional tray 2.

Load paper in the optional tray 2.

6-36

Service Manual

Samsung Electronics

7

7. Troubleshooting

7.1 Procedure of Checking the Symptoms

Before attempting to repair the printer first obtain a detailed description of the problem from the customer.

Troubleshooting

Power On

OP Panel

ON?

Ready or

Power save

Test Print printing

Quality is

Nomal?

END

- No Power

- Power Module error

- Main PBA error

- LCD Panel error

Indicate

Error Massage

Refer to "Solution of Image Problem"

Refer to

Error Massage

<Chapter 6.9>

Service Manual

7-1

Samsung Electronics

Troubleshooting

7.2 Solving other problems

The following chart lists some conditions that may occur and the recommended solutions. Follow the suggested solutions until the problem is corrected.

7.2.1 Paper Feeding Problems

Condition

Paper is jammed during printing.

Paper sticks together.

Clear the paper jam.

Suggested solutions

Multiple sheets of paper do not feed.

Paper does not feed into the machine.

The paper keeps jamming.

Transparencies stick together in the paper exit.

Envelopes skew or fail to feed correctly.

Ensure that there is not too much paper in the tray. The tray can hold up to

150 sheets of paper, depending on the thickness of your paper.

Make sure that you are using the correct type of paper.

Remove paper from the tray and flex or fan the paper.

Humid conditions may cause some paper to stick together.

Different types of paper may be stacked in the tray. Load paper of only one type, size, and weight.

If multiple sheets have caused a paper jam, clear the paper jam.

Remove any obstructions from inside the machine.

Paper has not been loaded correctly. Remove paper from the tray and reload it correctly.

There is too much paper in the tray. Remove excess paper from the tray.

The paper is too thick. Use only paper that meets the specifications required by the machine.

If an original does not feed into the machine, the ADF rubber pad may require to be replaced.

There is too much paper in the tray. Remove excess paper from the tray. If you are printing on special materials, use the mamual tray.

An incorrect type of paper is being used. Use only paper that meets the specifications required by the machine.

There may be debris inside the machine. Open the front cover and remove the debris.

If an original does not feed into the machine, the ADF rubber pad may require to be replaced.

Use only transparencies specifically designed for laser printers. Remove each transparency as it exits from the machine.

Ensure that the paper guides are against both sides of the envelopes.

7-2

Service Manual

Samsung Electronics

Troubleshooting

7.2.2 Printing problems

Condition

The machine does not print.

Possible cause

The machine is not receiving power.

Suggested solutions

Check the power cord connections. Check the power switch and the power source.

Select Samsung CLX-3160 Series as your default printer in your Windows.

The machine is not selected as the default printer.

Check the machine for the following:

The front cover is not closed. Close the cover.

Paper is jammed. Clear the paper jam.

No paper is loaded. Load paper.

The toner cartridge is not installed. Install the toner cartridge.

If a system error occurs, contact your service representative.

Disconnect the printer cable and reconnect it.

The connection cable between the computer and the machine is not connected properly.

The connection cable between the computer and the machine is defective.

If possible, attach the cable to another computer that is working properly and print a job. You can also try using a different printer cable.

The port setting is incorrect.

The machine does not print.

(continued)

The machine selects print materials from the wrong paper source.

The machine may be configured incorrectly.

The printer driver may be incorrectly installed.

The machine is malfunctioning.

The paper source selection in the printer properties may be incorrect.

Check the Windows printer setting to make sure that the print job is sent to the correct port. If the computer has more than one port, make sure that the machine is attached to the correct one.

Check the printer properties to ensure that all of the print settings are correct.

Repair the printer software.

See the Software Section.

Check the display message on the control panel to see if the machine is indicating a system error.

For many software applications, the paper source selection is found under the Paper tab within the printer properties. Select the correct paper source.

See the printer driver help screen.

Service Manual

7-3

Samsung Electronics

Troubleshooting

Condition

A print job is extremely slow.

Half the page is blank.

Possible cause

The job may be very complex.

If you are using Windows 9x/Me, the

Spool Setting may be set incorrectly.

The page orientation setting may be incorrect.

The paper size and the paper size settings do not match.

The machine prints, but the text is wrong, garbled, or incomplete.

The printer cable is loose or defective.

The wrong printer driver was selected.

Suggested solutions

Reduce the complexity of the page or try adjusting the print quality settings.

From the Start menu, choose Settings and then

Printers. Right-click the Samsung CLX-3160

Series machine icon, choose Properties, click the Details tab, and then choose the Spool

Settings button.

Select the desired spool setting.

Change the page orientation in your application. See the printer driver help screen.

Ensure that the paper size in the printer driver settings matches the paper in the tray.

Or, ensure that the paper size in the printer driver settings matches the paper selection in the software application settings you use.

Disconnect the printer cable and reconnect. Try a print job that you have already printed successfully. If possible, attach the cable and the machine to another computer and try a print job that you know works. Finally, try a new printer cable.

Check the application's printer selection menu to ensure that your machine is selected.

Pagesprint, but are blank.

The software application is malfunctioning.

The operating system is malfunctioning.

The toner cartridge is defective or out of toner.

The file may have blank pages.

Try printing a job from another application.

Exit Windows and reboot the computer. Turn the machine off and then back on again.

Redistribute the toner, if necessary.

If necessary, replace the toner cartridge.

Some parts, such as the controller or the board, may be defective.

The illustrations print incorrectly in

Adobe

Illustrator.

The setting in the software application is wrong.

Check the file to ensure that it does not contain blank pages.

Contact a service representative.

Select Download as Bit Image in the TrueType

Options window of the graphic properties and print the document again.

7-4

Service Manual

Samsung Electronics

Troubleshooting

7.2.3 Print Quality Problems

If the inside of the machine is dirty or paper has been loaded improperly, you may notice a reduction in print quality. See the table below to clear the problem.

Condition Suggested solutions

Light or faded print

If a vertical white streak or faded area appears on the page:

The toner supply is low. You may be able to temporarily extend the toner cartridge life.

If this does not improve the print quality, install a new toner cartridge.

Aa Bb Cc

Aa Bb Cc

Aa Bb Cc

Aa Bb Cc

Aa Bb Cc

The paper may not meet paper specifications; for example, the paper is too moist or too rough.

If the entire page is light, the print resolution setting is too low. Adjust the print resolution.

See the help screen of the printer driver.

A combination of faded or smeared defects may indicate that the toner cartridge needs cleaning.

The surface of the LSU part inside the machine may be dirty. Clean the LSU.

Toner specks

Aa Bb Cc

Aa Bb Cc

Aa Bb Cc

Aa Bb Cc

Aa Bb Cc

The paper may not meet specifications; for example, the paper is too moist or too rough.

The transfer roller may be dirty. Clean the inside of your machine.

The paper path may need cleaning.

Dropouts

AaBbCc

AaBbCc

AaBbCc

AaBbCc

AaBbCc

Vertical lines

AaBbCc

AaBbCc

AaBbCc

AaBbCc

AaBbCc

If faded areas, generally rounded, occur randomly on the page:

A single sheet of paper may be defective.

Try reprinting the job.

The moisture content of the paper is uneven or the paper has moist spots on its surface. Try a different brand of paper.

The paper lot is bad. The manufacturing processes can cause some areas to reject toner. Try a different kind or brand of paper.

If these steps do not correct the problem, contact a service representative.

If black vertical streaks appear on the page:

The drum inside the toner cartridge has probably been scratched. Remove the toner cartridge and install a new one.

If white vertical streaks appear on the page:

The surface of the LSU part inside the machine may be dirty. Clean the LSU.

Service Manual

7-5

Samsung Electronics

Troubleshooting

Condition

Color or Black background

AaBbCc

AaBbCc

AaBbCc

AaBbCc

AaBbCc

Toner smear

Suggested solutions

If the amount of background shading becomes unacceptable:

Change to a lighter weight paper.

Check the machine's environment: very dry (low humidity) or high humidity (higher than

80% RH) conditions can increase the amount of background shading.

Remove the old toner cartridge and install a new one.

Clean the inside of the machine.

Check the paper type and quality.

Remove the toner cartridge and install a new one.

Vertical repetitive defects

AaBbCc

AaBbCc

AaBbCc

AaBbCc

AaBbCc

If marks repeatedly appear on the printed side of the page at even intervals:

The toner cartridge may be damaged. If a repetitive mark occurs on the page, print a cleaning sheet several times to clean the cartridge. After the printout, if you still have the same problems, remove the toner cartridge and install a new one.

Parts of the machine may have toner on them. If the defects occur on the back of the page, the problem will likely correct itself after a few more pages.

The fusing assembly may be damaged. Contact a service representative.

Background scatter

Background scatter results from bits of toner distributed on the printed page.

The paper may be too damp. Try printing with a different batch of paper. Do not open

A

packages of paper until necessary so that the paper does not absorb too much moisture.

If background scatter occurs on an envelope, change the printing layout to avoid printing over areas that have overlapping seams on the reverse side.

Printing on seams can cause problems.

If background scatter covers the entire surface area of a printed page, adjust the print resolution through your software application or the printer properties.

Misformed characters

If characters are improperly formed and producing hollow images, the paper stock may be too slick. Try a different paper.

If characters are improperly formed and producing a wavy effect, the scanner unit may need service. For service, contact a service representative.

7-6

Service Manual

Samsung Electronics

Troubleshooting

Condition

Page skew

AaBbCc

AaBbCc

AaBbCc

AaBbCc

AaBbCc

Curl or wave

Suggested solutions

Ensure that the paper is loaded properly.

Check the paper type and quality.

Ensure that the paper or other material is loaded correctly and the guides are not too tight or too loose against the paper stack.

Ensure that the paper is loaded properly.

Check the paper type and quality. Both high temperature and high humidity can cause paper curl.

Turn the stack of paper over in the tray. Also try rotating the paper 180° in the tray.

Wrinkles or creases

Ensure that the paper is loaded properly.

Check the paper type and quality.

Turn the stack of paper over in the paper tray. Also try rotating the paper 180° in the tray.

Back of printouts aredirty

Aa Bb Cc

Aa Bb Cc

Aa Bb Cc

Aa Bb Cc

Aa Bb Cc

Solid Color or

Black pages

Check for leaking toner. Clean the inside of the machine.

The toner cartridge may not be installed properly.

Remove the toner cartridge and reinsert.

The toner cartridge may be defective and need replacing. Remove the toner cartridge and install a new one.

The machine may require repair. Contact a service representative.

A

Service Manual

7-7

Samsung Electronics

Troubleshooting

Condition

Loose toner

Suggested solutions

Clean the inside of the machine.

Check the paper type and quality.

Remove the toner cartridge and install a new one.

If the problem persists, the printer may require repair. Contact a service representative.

Character Voids

A

Character voids are white areas within characters that should be solid black:

If you are using transparencies, try another type of transparency. Because of the composition of transparencies, some character voids are normal.

You may be printing on the wrong surface of the paper. Remove the paper and turn it around.

The paper may not meet paper specifications.

Horizontal stripes

AaBbCc

AaBbCc

AaBbCc

AaBbCc

AaBbCc

If horizontally aligned black streaks or smears appear:

The toner cartridge may be installed improperly. Remove the cartridge and reinsert it.

The toner cartridge may be defective.

Remove the toner cartridge and install a new one.

If the problem persists, the machine may require repair. Contact a service representative.

Curl

If the printed paper is curled or paper does not feed into the printer:

Turn the stack of paper over in the paper tray. Also try rotating the paper 180° in the tray.

7-8

Service Manual

Samsung Electronics

Troubleshooting

7.2.4 Copying problems

Condition

Copies are too light or too dark.

Smears, lines, marks, or spots appears on copies.

Copy image is skewed.

Blank copies print out.

Image rubs off the copy easily.

Frequent copy paper jams occur.

Toner cartridge produces fewer copies than expected before running out of toner.

Suggested solutions

Use Darkness to darken or lighten the background of the copies.

If defects are on the original, press Darkness to lighten the background of your copies.

If no defects are on the original, clean the scan unit.

Ensure that the original is face down on the scanner glass or face up in the

ADF.

Check that the copy paper is loaded correctly.

Ensure that the original is face down on the scanner glass or face up in the

ADF.

Replace the paper in the tray with paper from a new package.

In high humidity areas, do not leave paper in the machine for extended periods of time.

Fan the stack of paper, then turn it over in the tray. Replace the paper in the tray with a fresh supply. Check/adjust the paper guides, if necessary.

Ensure that the paper is the proper paper weight. 75 g/m 2 (20 lb bond) paper is recommended.

Check for copy paper or pieces of copy paper remaining in the machine after a paper jam has been cleared.

Your originals may contain pictures, solids, or heavy lines. For example, your originals may be forms, newsletters, books, or other documents that use more toner.

The machine may be turned on and off frequently.

The scanner lid may be left open while copies are being made.

Service Manual

7-9

Samsung Electronics

Troubleshooting

7.2.5 Scanning problems

Condition

The scanner does not work.

The unit scans very slowly.

Message appears on your computer screen:

"Device can't be set to the H/W mode you want."

"Port is being used by another program."

"Port i s Disabled.

"Scanner is busy receiving or printing data. When the current job is completed, try again."

"Invalid handle."

"Scanning has failed."

Suggested solutions

Make sure that you place the original to be scanned face down on the scanner glass, or face up in the ADF.

There may not be enough available memory to hold the document you want to scan. Try the Prescan function to see if that works. Try lowering the scan resolution rate.

Check that the USB cable is connected properly.

Make sure that the USB cable is not defective. Switch the cable with a known good cable. If necessary, replace the cable.

Check that the scanner is configured correctly. Check scan setting in the

SmarThru Configuration or the application you want to use to make certain that the scanner job is being sent to the correct port.

Check if the machine is printing received data. If so, scan the document after the received data has been printed.

Graphics are scanned more slowly than text.

Communication speed slows in scan mode because of the large amount of memory required to analyze and reproduce the scanned image. Set your computer to the ECP printer mode through BIOS setting. It will help to increase the speed. For details about how to set BIOS, refer to your computer user's guide.

There may be a copying or printing job in progress. When that job is complete, try your job again.

The Selected port is currently being used.

Restart your computer and try again.

The printer cable may be improperly connected or the power may be off.

The scanner driver is not installed or the operating environment is not set up properly.

Ensure that the machine is properly connected and the power is on, Then restart your computer.

The USB cable may be improperly connected or the power may be off.

7-10

Service Manual

Samsung Electronics

Troubleshooting

7.2.6 Network Scan problems

Condition

I cannot find a scanned image file.

I cannot find the scanned image file after scanning.

Suggested solutions

You can check the scanned file's destination in the Advanced page in the

Network Scan program's Properties screen.

Check if the scanned file's application is on your computer.

Check Open immediately with the default application in the Advanced page in the Network Scan program's Properties screen to open the scanned image immediately after scanning.

I forgot my ID and PIN.

I cannot view the Help file.

Check your ID and PIN in the Server page in the Network Scan program's

Properties screen.

To view the Help file, you need to have Internet Explorer 4 service pack 2 or above.

I cannot use the Samsung Network

Scan Manager.

Check your operating system. Supporting operating systems are Windows

98/Me/NT 4.0/2000/XP/2003.

7.2.7 Fax problems (CLX-3160FN only)

Condition

The machine is not working, there is no display and the buttons are not working.

No dial tone sounds.

Suggested solutions

Unplug the power cord and plug it in again.

Ensure that there is power to the electrical outlet.

The numbers stored in memory do not dial correctly.

The original does not feed into the machine.

Check that the phone line is connected properly.

Check that the phone socket in the wall is working by plugging in another phone.

Make sure that the numbers are stored in memory correctly.

Faxes are not received automatically.

Make sure that the paper is not wrinkled and you are putting it in correctly.

Check that the original is the right size, not too thick or thin

Make sure that the ADF is firmly closed.

The ADF rubber pad may need to be replaced.

The receiving mode should be set to Fax.

Make sure that there is paper in the tray.

Check to see if the display shows any error message. If it does, clear the problem.

Service Manual

7-11

Samsung Electronics

Troubleshooting

Condition

The machine does not send.

The incoming fax has blank spaces or is of poor-quality.

Suggested solutions

Make sure that the original is loaded in the ADF or on the scanner glass.

Sending should show up on the display.

Check the fax machine you are sending to, to see if it can receive your fax.

The fax machine sending you the fax may be faulty.

A noisy phone line can cause line errors.

Check your machine by making a copy.

The toner cartridge may be empty.

Some of the words on an incoming fax are stretched.

There are lines on the originals you send.

The fax machine sending you the fax had a temporary document jam.

Check your scan unit for marks and clean it.

The machine dials a number, but a connection with the other fax machine fails.

Faxes do not store in memory.

The other fax machine may be turned off, out of paper, or cannot answer incoming calls.

Speak with the other machine operator and ask her/him to sort out the problem.

There may not be enough memory space to store the fax. If the display shows the Memory Full message, delete from memory any faxes you no longer need and then try again to store the fax.

Blank areas appear at the bottom of each page or on other pages, with a small strip of text at the top.

You may have chosen the wrong paper settings in the user option setting.

For details about paper settings.

7.2.8 Common Windows problems

"File in Use" message appears during installation.

"Error Writing to LPTx" message appears.

Condition Suggested solutions

Exit all software applications. Remove all software from the StartUp Group, then restart Windows. Reinstall the printer driver.

Ensure that the cables are connected correctly, the machine is on.

If bi-directional communication is not turned on in the driver, it will also cause this message.

Close all other applications, reboot Windows and try printing again.

"General Protection Fault",

"Exception OE", "Spool32", or

"Illegal Operation" messages appear.

"Fail To Print", "A printer timeout error occurred." messages appear.

These messages may appear during printing. Just keep waiting until the machine finishes printing. If the message appears in standby mode or after printing has been completed, check the connection and/or whether an error has occurred.

7-12

Service Manual

Samsung Electronics

Troubleshooting

7.2.9 Common Linux problems

Condition

The machine does not print.

The machine does not appear on the scanners list.

Suggested solutions

Check if the printer driver is installed in your system. Open MFP configurator and switch to the Printers tab in Printers configuration window to look at the list of available printers. Make sure that your machine is displayed on the list. If not, please, invoke Add new printer wizard to set up your device.

Check if the printer is started. Open Printers configuration and select your machine on the printers list. Look at the description in the Selected printer pane. If its status contains "(stopped)" string, please, press the Start button. After that normal operation of the printer should be restored.

The "stopped" status might be activated when some problems in printing occurred. For instance, this could be an attempt to print document when

MFP port is claimed by a scanning application.

Check if the MFP port is not busy. Since functional components of MFP

(printer and scanner) share the same I/O interface (MFP port), the situation of simultaneous access of different "consumer" application to the same

MFP port is possible. To avoid possible conflicts, only one of them at a time is allowed to gain control over the device.

The other "consumer" will encounter "device busy" response. You should open MFP ports configuration and select the port assigned to your printer.

In the Selected port pane you can see if the port is occupied by some other application. If this is the case, you should wait for completion of the current job or should press Release port button, if you are sure that the present owner is not functioning properly.

Check if your application has special print option such as "-oraw". If "-oraw" is specified in the command line parameter then remove it to print properly.

For Gimp front-end, select "print" -> "Setup printer" and edit command line parameter in the command item.

Check if your machine is attached to your computer. Make sure that it is connected properly via the USB port and is turned on.

Check if the scanner driver for your machine is installed in your system.

Open MFP Configurator, switch to Scanners configuration, then press

Drivers. Make sure that driver with a name corresponding to your machine's name is listed in the window.Check if the MFP port is not busy.

Since functional components of MFP (printer and scanner) share the same

I/O interface (MFP port), the situation of simultaneous access of different

"consumer" application to the same MFP port is possible. To avoid possible conflicts, only one of them at a time is allowed to gain control over the device. The other "consumer" will encounter "device busy" response.

This can usually happen while starting scan procedure, and appropriate message box appears.

To identify the source of the problem, you should open MFP ports configuration and select the port assigned to your scanner. MFP port's symbol /dev/mfp0 corresponds to LP:0 designation displayed in the scanners' options, /dev/mfp1 relates to LP:1 and so on. USB ports start at

/dev/mfp4, so scanner on USB:0 relates to /dev/mfp4 respectively and so forth sequentially. In the Selected port pane you can see if the port is occupied by some other application. If this is the case, you should wait for completion of the current job or should press Release port button, if you are sure that the present port's owner is not functioning properly.

Service Manual

7-13

Samsung Electronics

Troubleshooting

Condition

The machine does not scan.

Suggested solutions

Check if a document is loaded into the machine.

Check if your machine is connected to the computer. Make sure if it is connected properly if I/O error is reported while scanning.

Check if the MFP port is not busy. Since functional components of MFP

(printer and scanner) share the same I/O interface (MFP port), the situation of simultaneous access of different "consumer" application to the same

MFP port is possible. To avoid possible conflicts, only one of them at a time is allowed to gain control over the device.

The other "consumer" will encounter "device busy" response. This can usually happen while starting scan procedure, and appropriate message box will be displayed.

To identify the source of the problem, you should open MFP ports configuration and select the port assigned to your scanner. MFP port's symbol /dev/mfp0 corresponds to LP:0 designation displayed in the scanners' options, /dev/mfp1 relates to LP:1 and so on. USB ports start at

/dev/mfp4, so scanner on USB:0 relates to /dev/mfp4 respectively and so forth sequentially. In the Selected port pane you can see if the port is occupied by some other application. If this is the case, you should wait for completion of the current job or should press Release port button, if you are sure that the present port's owner is not functioning properly.

I cannot print when I installed both

Linux Print Package (LPP) and

MFP driver on the same machine simultaneously.

I cannot scan via Gimp Front-end.

Since both Linux Printer Package and MFP driver make a symbolic link to

"lpr" printing command, which is commonly used on Unix clones, it is not recommended to use both package on the same machine.

If you still want to use both packages simultaneously, please install the

LPP first.

If you want to uninstall only one of them, please uninstall both packages and install that one you want to use again.

If you don't want to uninstall MFP driver and install it again, you may make the necessary symbolic link yourself.

Please, log in as root user and invoke the following command: ln -sf /usr/local/bin/samsung/slpr /usr/bin/lpr

Check if Gimp Front-end has "Xsane:Device dialog." on the "Acquire" menu. If not, you should install Xsane plug-in for Gimp on the your computer. You can find Xsane plug-in package for Gimp on Linux distribution CD or Gimp home page. For the detail information, refer to the

Help for Linux distribution CD or Gimp Front-end application.

If you wish to use other kind of scan application, refer to the Help for application.

I encounter error "Cannot open

MFP port device file" when printing a document.

Please avoid changing print job parameters (via SLPR utility, for example) while a print job is in progress. Known versions of CUPS server break the print job whenever print options are changed and then try to restart the job from the beginning. Since Linux MFP driver locks MFP port while printing, the abrupt termination of the driver keeps the port locked and therefore unavailable for subsequent print jobs. If this situation occurred, please, try to release the MFP port.

7-14

Service Manual

Samsung Electronics

Troubleshooting

7.2.10 Common Macintosh problems (CLX-3160FN only)

Condition

The printer does not print a document from Acrobat Reader.

The document has printed, but the print job has not disappeared from the spooler in Mac OS 10.3.2.

Suggested solutions

You should change the Print Method option to Print as Image when you print from Acrobat Reader.

Update your Mac OS to OS 10.3.3. or higher.

Samsung Electronics

Service Manual

7-15

8

8. Exploded Views and Parts List

8.1 Main

8.2 Middle Cover

8.3 Front Cover

8.4 Right Cover

8.5 Round Cover

8.6 Rear Cover

8.7 Cover Platen

8.8 Platen Ass'y

8.9 OPE(CLX-3160FN)

OPE(CLX-3160N)

8.10 Scan Ass'y

8.11 ADF Ass'y

8.12 ADF Lower

8.13 ADF Motor

8.14 Frame

8.15 Main Driver

8.16 LSU Cover

8.17 ITB Unit

8.18 OPC DEVE

8.19 Fuser Ass'y

8.20 Cassette

Exploded Views & Parts List

8-13

8-14

8-15

8-16

8-18

8-8

8-9

8-10

8-11

8-12

8-20

8-21

8-22

8-24

8-25

8-2

8-3

8-4

8-5

8-6

8-7

Service Manual

8-1

Samsung Electronics

Exploded Views & Parts List

8.1 Main

8-2

Service Manual

Samsung Electronics

Exploded Views & Parts List

8.2 Middle Cover

0

13

7

9

8

8

10

12

11

1

2

3

6

Samsung Electronics

4

14

5

Service Manual

8-3

Exploded Views & Parts List

8.3 Front Cover

1

0

2

8-4

Service Manual

Samsung Electronics

Exploded Views & Parts List

8.4 Right Cover

0

3

2

1

Service Manual

8-5

Samsung Electronics

Exploded Views & Parts List

8.5 Round Cover

0

1

8-6

Service Manual

2

Samsung Electronics

Exploded Views & Parts List

8.6 Rear Cover

0

7

2

Samsung Electronics

10

5

1

8

9

9

4

3

6

8

Service Manual

8-7

Exploded Views & Parts List

8.7 Cover Platen

0

1-3

9

8

5

1-4

1-5

7

6

5

7

1-2

1-1

1

4

4

3

2

8-8

Service Manual

Samsung Electronics

Exploded Views & Parts List

8.8 Platen Ass'y

0

1-1-4

1-1-5

1-1-3

1-1-2

1-1-4

1-1-1

1-1

1-1-6

1

1-2

1-5

2-2-5

2-2-4

2-2-3

2-2-2

2-2-1

2-2-7

Samsung Electronics

2

1-5

2-2-6

2-2

1-3

1-4

2-10

2-3

2-5

2-19

2-4

2-23

2-17

2-15

2-13

2-12

2-11

2-13

2-14

2-21

2-9

2-8

2-7

2-6

2-1

2-20

2-22

2-16-1

2-16-2

2-16

2-18

2-24

Service Manual

8-9

Exploded Views & Parts List

8.9 OPE(CLX-3160FN)

4

5

2

0

17

20

24

24

19

18

8

13

12

14

15

22

7

16

6

10

9

11

1

21

3

23

24

24

8-10

Service Manual

Samsung Electronics

Exploded Views & Parts List

8.9 OPE(CLX-3160N)

2

1

Samsung Electronics

11

12

9

10

13

15

18

5

3

16

17

17

17

17

7

4

6

8

14

17

17

0

Service Manual

8-11

Exploded Views & Parts List

8.10 Scan Ass'y

8-12

Service Manual

Samsung Electronics

Exploded Views & Parts List

8.11 ADF Ass'y

3-1

5-3

5-2

5-2

3-2-5

3-2

3-2-2

3-3

3-2-4

3-2-3

3-2-1

5-1

5

0

3

4

4-2

4-3

4-6

4-1

4-18

4-5

4-4

4-10

4-11

4-9

4-8

4-12

4-15

4-17

4-7

4-8A

4-8B

4-16B

4-15

4-14

4-16A

4-13

2

1

7

6

Service Manual

8-13

Samsung Electronics

Exploded Views & Parts List

8.12 ADF Lower

24

9

6

16

5

18

5

14

5

6

17

1

12

2

20

13

6

6

10

11

4

8

19

15

2

7

21

22

23

8-14

Service Manual

3

7

8

Samsung Electronics

8.13 ADF Motor

Exploded Views & Parts List

Samsung Electronics

Service Manual

8-15

Exploded Views & Parts List

8.14 Frame-1

8-16

Service Manual

Samsung Electronics

Frame-2

Exploded Views & Parts List

Samsung Electronics

Service Manual

8-17

Exploded Views & Parts List

8.15 Main Driver-1

8-18

Service Manual

Samsung Electronics

Main Driver-2

Exploded Views & Parts List

Samsung Electronics

Service Manual

8-19

Exploded Views & Parts List

8.16 LSU Cover

8-20

Service Manual

3

4

0

5

1

2

6

Samsung Electronics

Exploded Views & Parts List

8.17 ITB Unit

29

61

9

17

13

64

72

9

21

26

14

6 6

6

49

47

31

19

6

76

27

55

40

46

33

15

34

36

37

38

43

57

48

39

30

35

65

18

42

28

44

52

41

54

51

32

39

59

62

6

53

6

58

27

10

7

40

23

45

68

37

38

7

7

24

20

8

16

22

5

8

25

56

60

6

0

6

50

6

6

Service Manual

8-21

Samsung Electronics

Exploded Views & Parts List

8.18 OPC DEVE

8-22

Service Manual

Samsung Electronics

Exploded Views & Parts List

Samsung Electronics

Service Manual

8-23

Exploded Views & Parts List

8.19 Fuser Ass'y

8-24

Service Manual

Samsung Electronics

8.20 Cassette

Exploded Views & Parts List

Samsung Electronics

Service Manual

8-25

Parts List

Service Parts List (Model code : CLX-3160FN/XAA)

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

8.1-1

8.1-2

8.1-3

8.1-4

SEC-Code

JC97-02683A

JC96-03929A

JC96-04089A

JC97-02690A

Description & Specification

MEA UNIT-FRAME;CLX-3160FN,SEC,WORLD,-,-,

ELA HOU-SCAN_4IN1;CLX-3160FN/XAA,SEC,-,4

ELA UNIT-COVER MIDDLE;CLX-3160FN,SEC,WOR

MEA UNIT-COVER ROUND;CLX-3160FN,SEC,WORL

Location Service

SA

SA

SA

SA

8.1-18

8.1-19

8.1-21

8.1-22

8.1-23

8.1-24

8.1-25

8.1-26

8.1-27

8.1-28

8.1-29

8.1-30

8.1-5

8.1-6

8.1-7

8.1-8

8.1-9

8.1-10

8.1-11

8.1-12

8.1-13

8.1-14

8.1-15

8.1-16

8.1-17

JC92-01707D PBA MAIN-CONT_FN;CLX-3160,SEC,KOREA,NETW

JC96-03608A ELA UNIT-DRIVE MAIN;CLP-300,SEC,WORLD,-,

JC96-03610A ELA UNIT-OPC DEV_SET;CLP-300,SEC,EXPORT,

JC96-03611A ELA UNIT-ITB_SET;CLP-300,SEC,WORLD,SET,-

JC97-02615A MEA UNIT-DEV C;CLP-300,SEC,EXPORT,-,-,-,

JC97-02614A MEA UNIT-DEV M;CLP-300,SEC,EXPORT,-,-,-,

JC97-02613A MEA UNIT-DEV Y;CLP-300,SEC,EXPORT,-,-,-,

JC97-02616A MEA UNIT-DEV K;CLP-300,SEC,EXPORT,-,-,-,

JC97-02332A

JC63-01023A

JC97-02440A

JC97-02684A

JC97-02799A

MEA-UNIT CASSETTE;CLP-300,SEC,WORLD,-,-,

COVER-M-LEFT;CLX-3160FN,PC-ABS,T2.5,W424

MEA UNIT-COVER REAR;CLP-300,SEC,WORLD,-,

MEA UNIT-COVER FRONT;CLX-3160FN,SEC,WORL

MEA UNIT-COVER RIGHT;CLX-3160FN,-,WORLD,

JC63-00863A SHIELD-P-MAIN LOWER;CLP-300,SECC,T1.0,99

JC44-00097A SMPS-PSP_TYPE3_V1;SCX-4521F,*,AC/DC,-,10

JC97-02656A MEA UNIT-COVER LSU;CLP-300,SEC,EXPORT,-,

JC59-00018E UNIT-LSU;CLP-300,-,-,STANDARD SINGLEBEAM

JC96-04088B ELA UNIT-FUSER;CLX-3160FN/XAA,SEC,WORLD,

JC61-01660A GUIDE-M HARNESS;CLX-3160FN,ABS,5V,T2.5,W

JC39-00496A CBF HARNESS-LSU_GND;CLP-300,WIRE HARNESS

JC39-00483A CBF HARNESS-LSU;CLP-300,WIRE HARNESS,UL1

JC39-00484A CBF HARNESS-SMPS;CLP-300,WIRE HARNESS,UL

3903-000085 CBF-POWER CORD;DT,US,BP3/YES,I(IEC C13/C

JC63-00934A COVER-M_LEFT UPPER;SCX-5530FN,HIPS,2.5,9

JC63-00933A COVER-M_RIGHT UPPER;SCX-5530FN,HIPS,2.5,

Z4403

SA

SA

Z4496 SNA

Z4404 SA

Z4625 SNA

Z4624 SNA

Z4623 SNA

Z4626 SNA

Z4405 SA

Z4407

SA

SA

SA

SA

Z4501 SNA

D2114 SA

Z4412

Z4411

SA

SA

SA

SA

SA

SA

C0022

Z4309

Z4310

SA

SA

SA

SA

8.2-3

8.2-3

8.2-3

8.2-3

8.2-4

8.2-5

8.2-5

8.2-6

8.2-7

8.2-8

8.2-9

8.1-31

8.1-32

8.1-33

8.1-34

8.1-35

8.1-37

8.1-38

8.1-38

JC63-01030A

6103-001049

JC63-01148A

JC97-02807A

JC39-00570A

JC39-00486A

JF39-50094B

JC97-02619A

SHIELD-P-LIU;CLX-3160FN,SECC,T0.8,W96.9,

SUPPORTER;DASS-T4N,L30.8,NTR,NYLON6/6

SHEET-LIU;CLX-3160FN,PC,T0.5,W160,L70,TR

MEA UNIT-LIU;CLX-3160FN,-,WORLD,-,-,-,-

CBF SIGNAL-FAX;CLX-3160,30PIN,FFC,150MM,

CBF HARNESS-BLDC;CLP-300,WIRE HARNESS,UL

CBF LINE CORD;MINI FAX,-,-,IVR,-

MEA UNIT-TONER WASTE;CLP-300,SEC,EXPORT,

Replacement JC69-00960A BOX-MAIN;CLX-3160FN,OFFSET4,A-1,638,610,

Replacement JC92-01746A PBA SUB-MODEM;SCX-5530FN,-,-,-,-,-,-,114

8.2-1

8.2-2

JC63-01027A

3001-001591

COVER-M-MIDDLE;CLX-3160FN,HIPS,T2.5,W420

SPEAKER;0.4W,8OHM,87DB,480HZ

6003-000196 SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRC

6003-000152 SCREW-TAPTITE;PH,+,B,M2,L10,ZPC(YEL),SWR

6003-000261 SCREW-TAPTITE;BH,+,B,M3,L6,ZPC(YEL),SWRC

6002-000308 SCREW-TAPTITE;PH,+,B,M2.6,L6,ZPC(YEL),SW

JC66-01221A LEVER-M ACT OUTFULL;CLX-3160FN,PC,D4.5,W

0604-001095 PHOTO-INTERRUPTER;TR,90%,150mW,DIP-4,BK

0604-001154 PHOTO-INTERRUPTER;TR,0.2-1.0MA,80MW,DIP,

JC63-00944A COVER-M_STACKER RX;SCX-5530FN,HIPS,2.5,7

JC31-00027C

JC66-01220A

JC61-01656A

FAN;-,CLX-3160FN,-,-,225MM*2PIN

LEVER-M STACKING;CLX-3160FN,PC,D4.0,-,L4

GUIDE-M-OUTPUT FUSER;CLX-3160FN,PET+GF30

SA

DNA

SA

SA

SNA

SA

Z4186 SA

Z4627 SNA

Z4299

SA

SA

SA

SA

Z4397

Z4442

SA

SA

Z4603 SNA

Z4443 SA

P0013

P0012

Z4312

SNA

SA

SA

SA

SA

SNA

SA

1

Parts List

8.8-1-1-1

8.8-1-1-2

8.8-1-1-3

8.8-1-1-4

8.8-1-1-5

8.8-1-1-6

8.8-1-2

8.8-1-3

8.8-1-4

8.8-1-5

8.8-2

8.8-2-1

8.8-2-2

8.7-1-5

8.7-2

8.7-3

8.7-4

8.7-5

8.7-6

8.7-7

8.7-8

8.7-9

8.8-0

8.8-1

8.8-1-1

8.8-2-2-1

8.8-2-2-2

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

8.2-10

8.2-11

8.2-12

8.2-13

SEC-Code

JC63-01025A

JC92-01636A

JC39-00571A

JC68-01760A

Description & Specification

COVER-M-JAM;CLX-3160FN,HIPS,T2.5,W243.1,

PBA SUB-USB HOST;SCX-4720F,SEC,-,USB HOS

CBF HARNESS-USB_HOST;CLX-3160,WIRE HARNE

LABEL-INFORMATION;ML-4550,SEC,ART PAPER

Location Service

L0439

SA

SA

SA

SNA

8.6-6

8.6-7

8.6-8

8.6-8

8.6-8

8.6-9

8.6-10

8.7-1

8.7-1-1

8.7-1-2

8.7-1-3

8.7-1-4

8.2-14

8.3-1

8.3-2

8.3-2

8.4-1

8.4-2

8.5-1

8.5-2

8.6-1

8.6-2

8.6-3

8.6-4

8.6-5

JC39-00564A CBF HARNESS-BIN_FULL;CLX-3160,WIRE HARNE

JC63-01022A COVER-M-FRONT;CLX-3160FN,HIPS,T2.5,W461.

JC68-01732A LABEL-INSTRUCTION;CLX-3160FN,-,PP150G,15

JC68-01684A LABEL-INSTRUCTION;SCX-5530FN,SEC,YUPO PA

JC63-01024A COVER-M-RIGHT;CLX-3160FN,PC + ABS,T2.5,W

JC63-01174A COVER-M-RIGHT-GRILL;CLX-3160FN,PC+ABS,2.

JC63-01026A COVER-M-REAR_MFP;CLX-3160FN,HIPS,T2.5,W4

JC67-00160A CAP-NETWORK;CLP-300,EPDM,T4.5,20.5,20,G3

JC63-00844A

JC64-00215A

JC66-01089A

JC61-01461A

JC61-01456A

COVER-M-REAR;CLP-300,ABS,T3.0,249.3,296.

BUTTON-M-OPEN REAR;CLP-300,ABS FR V0,80.

SHAFT-P-LOCKBAR REAR;CLP-300,SECC,284,6,

HOLDER-M-HOOK REAR R;CLP-300,POM,T5.0,19

HOLDER-M-HOOK REAR L;CLP-300,POM,T5.0,19

JC61-01462A HOLDER-M-HOOK REAR C;CLP-300,POM,T5.0,19

JC66-01071A LEVER-M-REAR LOCK;CLP-300,HIPS,T2.5,55.1

6107-001268 SPRING-TS;SUS304 WPB,-,PI0.9,D8.9,L7,-,-

6107-001283 SPRING-TS;SWRS82A,-,1.0X0.6,D13.70,L12.1

6107-001284 SPRING-TS;SWRS82A,-,0.75X0.5,-,L8.4,-,-,

6002-000440 SCREW-TAPPING;PWH,+,-,2,M3,L8,ZPC(BLK),S

JC96-03990A ELA UNIT-TRANSFER;CLP-300,SEC,EXPORT,-,-

JC97-02406A MEA-TX STACKER;SCX-5530FN,SEC,-,-,-,-,-

JC63-00988A COVER-M_STACKER TX;SCX-5530FN,HIPS,-,266

JC61-01609A GUIDE-M_DOCU L;SCX-5530FN,HIPS,-,128.5,6

JC61-01610A GUIDE-M_DOCU R;SCX-5530FN,HIPS,-,128,60,

JF70-10616A IPR-WASHER SPRING CU;CF3400,SUS301-CSP,-

JG66-40003A GEAR-PINION;SF4000,POM,WHT,M1,Z16

JC63-00984A COVER-M_PLATEN;SCX-5530FN,ABS,-,339.03,4

JC63-00209B SHEET-WHITE SPONGE;SCX-4216F,SPONGE+SHEE

JC97-02779A MEA UNIT-HINGE;SCX-5330N,-,-,ELBERT,-,-,

JC61-00011A SPRING ETC-FEED;SF-5100,SUS304WPB,0.6,-,

JF70-40521B ICT-SHAFT PINCH;FX2200,STSC304WPA,-,D2.6

JG72-40663A PMO-ROLL PINCH;SF5500,POM(DERLIN 500P),B

JC66-00909A SHAFT-IDLE FEED;SCX-4521F,SUS303F,59.5,2

JC66-00728A ROLLER-ADF FEED;SCX-4920N,POM + EPDM,-,-

JC96-03917A ELA HOU-PLATEN;CLX-3160FN/XAA,SEC,-,-,-,

JC97-02412A MEA-SCAN UPPER;SCX-5530FN,SEC,-,-,-,-,-

JC97-02429A MEA UNIT-SCAN DUMMY;SCX-5530FN,SEC,-,-,-

JC63-00152F COVER-M_SCAN DUMMY;SCX-5530FN,HIPS,-,63.

JC74-00021A MCT-GLASS ADF;SCX-4216F,GLASS,238.4*19.1

0203-001744 TAPE-DOUBLE FACE;3M9495MP,-,T0.12,W3,L22

JC02-00013A TAPE ETC-DOUBLE TAPE SMALL;9448HK,DOUBLE

JB68-00644A LABEL(P)-SHADING;COMMON,YOOPO PAPER ,T0.

0203-001266 TAPE-DOUBLE FACE;3M9448HK,T0.16,W4,L280,

JC63-00990A COVER-M_SCAN UPPER;SCX-5530FN,ABS,-,330.

JC01-00001A GLASS-SCAN;329.9*247.5,2.8,-

0203-001267 TAPE-DOUBLE FACE;3M9448HK,T0.16,W8,L280,

JB70-00148A IPR-HOLDER GLASS;SCX-1110/XRX,SUS304,-,1

JC96-03918A ELA HOU-SCAN LOWER;CLX-3160FN/XAA,SEC,-,

JC63-00989B COVER-M_SCAN LOWER;CLX-3160FN,ABS,T2.5,W

JC96-03069A

JC61-00895A

JC66-00531A

ELA HOU-SCAN MOTOR;SCX-4920N,DELL,-,SCAN

BRACKET-SCAN MOTOR R2;SCX-4920N,PC GF10%

GEAR-TIMING;SCX-6320F,POM(M90-44),M0.5,Z

SA

SA

SNA

SNA

SA

SNA

SA

SNA

Z4514 SNA

Z4515 SNA

Z4516 SNA

Z4517 SNA

Z4518 SNA

Z4519 SNA

Z4520 SNA

Z4419

Z4420

SA

SA

Z4521 SNA

Z4418 SA

Z4421

Z4345

SA

SA

Z4346

SNA

SNA

SNA

SA

O1127

Z4347

Z4348

Z4349

Z4350

Z4351

Z4352

Z4324

Z4325

Z4326

G1009

SA

SNA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

Z4177

G1004

Z4327

M2043

Z4328

G0434

SA

SA

SNA

SNA

SA

SNA

SNA

SA

SNA

SA

SA

SNA

SA

SA

SA

2

Parts List

8.9-8

8.9-9

8.9-10

8.9-11

8.9-12

8.9-13

8.9-14

8.9-15

8.9-16

8.9-17

8.9-18

8.9-19

8.9-20

8.8-2-21

8.8-2-22

8.8-2-23

8.8-2-24

8.9-0

8.9-1

8.9-2

8.9-3

8.9-4

8.9-5

8.9-6

8.9-7

8.9-21

8.9-22

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

8.8-2-2-3

8.8-2-2-4

8.8-2-2-5

8.8-2-2-5

SEC-Code

JB72-00764A

6044-000125

JB66-00083A

JC66-01108A

Description & Specification

PMO-HOLDER BELT;SCX-1110/XRX,-,POM,WHT,-

RING-E;ID4,OD9,T0.6,PASS,STSC

GEAR-IDLE;SCX-1110/XRX,POM,0.5,31,-,WHT,

GEAR-IDLE;CLP-300,POM DE8903,M0.6/M0.5,Z

Location Service

Z4329

R0004

Z4330

SA

SA

SA

SNA

8.8-2-2-6

8.8-2-2-7

8.8-2-3

8.8-2-4

8.8-2-5

8.8-2-6

8.8-2-7

8.8-2-10

8.8-2-11

8.8-2-11

8.8-2-11

8.8-2-11

8.8-2-11

8.8-2-11

8.8-2-11

8.8-2-12

8.8-2-14

8.8-2-16

8.8-2-16-1

8.8-2-16-2

8.8-2-17

8.8-2-18

8.8-2-19

8.8-2-20

8.8-2-21

JC66-00530A GEAR-REDUCTION73/37;SCX-6320F,POM(M90-44

JB31-00011A MOTOR STEP-SCAN;M42SP-4TKC,SCX-1110/XRX,

JC96-03819A ELA HOU-CCDM_2905;SCX-5525DN,-,-,-,-,-,-

JB70-00145A ICT-SHAFT CCD;SCX-1110/XRX,SUM24L,8,-,-,

JC39-00569A CBF SIGNAL-CCD;CLX-3160,24PIN,FFC,770mm,

JB72-00763A PMO-PULLEY;SCX-1110/XRX,-,POM,WHT,-,-,-

6602-001067 BELT-TIMING GEAR;HIBER GLASS,T3.2,T80-40

JB61-00059A SPRING ETC-BELT;SCX-1110/XRX,SUS304WP,¥Õ

6107-001135

6107-001306

6107-001309

6107-001278

6107-001282

SPRING-CS;SUS304 WPB,-,PI0.3,-,L14,-,-,I

SPRING-CS;SUS304-WPB,-,PI0.55,D6.45,L11,

SPRING-CS;SWP-B,-,PI0.5,-,L10,-,-,ID4.0,

SPRING-CS;SUS304 WPB,-,PI0.7,D6.9,L20,-,

SPRING-CS;C5210W,-,PI0.6,-,L12.5,-,-,ID3

6107-001288 SPRING-CS;SUS304-WPB,-,PI0.35,D3.55,L12,

6107-001303 SPRING-CS;SWP-B,-,PI1.3,-,L45.5,-,-,ID4.

JC72-00755A PMO-LEVER SENSOR;SCX-5100,POM,BLK,-,-,HB

JC39-00563A CBF HARNESS-COVE_OPEN;CLX-3160,WIRE HARN

JB96-01381A ELA UNIT-CORE;SCX-1100,SAMSUNG,CORE ASS'

3301-001413 CORE-FERRITE;AD,33x12x7mm,1500,2800Gauss

JB68-00705A LABEL(R)-DOUBLE CORE;COMMON,-,-,-,-,COMP

JC39-00648A HARNESS-B_FULL;CLX-3160,HARNESS,UL1061,4

JC61-00894B HOLDER-M_CCD;SCX-4720F/XRX,HIPS,2,43.6,3

JC39-00566A CBF HARNESS-DRAW_JOIN;CLX-3160,WIRE HARN

JB70-00154A ICT-INSERT SHAFT;SCX-1110/XRX,SUM24L,5,-

JC68-01702A LABEL-CAUTION;SCX-5530FN,-,WHITE PET,0.0

G0412

Z4331

Z4332

Z4334

Z4335

B2030

Z4336

Z4507

Z4416

Z4456

Z4631 SNA

SNA

L4074 SA

SA

Z4339

Z4340

SA

SA

SNA

SA

Z4342 SA

SA

SNA

SNA

SA

SA

SA

SNA

SNA

SA

SA

SA

SA

SA

SNA

SA

SA

JC68-01825A LABEL-CAUTION;CLP-300,SEC,WHITE POLY,-,W

JC92-01798A PBA SUB-JOINT;CLX-3160,SEC,KOREA,IRIS,-,

JC39-00485A CBF HARNESS-HVPS;CLP-300,WIRE HARNESS,UL

JC39-00567A CBF HARNESS-SYS_GND;CLX-3160,WIRE HARNES

JC96-03913A ELA HOU-OPE 4IN1;CLX-3160FN/XAA,SEC,-,-,

JC63-01020A COVER-M-OPE 4IN1;CLX-3160FN,HIPS,T2.5,W4

JC63-00991A COVER-M_NEVI;SCX-5530FN,HIPS,2,82.6,87.8

JC63-00993A COVER-M_LCD;SCX-5530FN,PC,1,86.6,39,-,-,

JC63-00999A SHEET-ONETOUCH;SCX-5530FN,PC ,0.38T,66.5

JC68-01639A LABEL-ONETOUCH;SCX-5530FN,SEC,ART PAPER,

JC64-00239A KEY-M_TEL;SCX-5530FN,ABS,60.2*66.1*14.5,

JC64-00240A KEY-M_COPY;SCX-5530FN,ABS,55*46.6*14,HB,

JC64-00241A KEY-M_FAX;SCX-5530FN,ABS,22.8*55*14,HB,D

JC64-00242A KEY-M_STOP CLEAR;SCX-5530FN,HIPS,18.6*8.

JC64-00243B KEY-M_START BLACK;CLX-3160FN,HIPS,19.1*1

JC64-00259A KEY-M-START COLOR;CLX-3160FN,HIPS,19.1*1

JC64-00245A KEY-M_MODE COPY;SCX-5530FN,PMMA,16.4*20.

JC64-00246A KEY-M_MODE FAX;SCX-5530FN,PMMA,16.4*20.4

JC64-00247A KEY-M_MODE SCAN;SCX-5530FN,PMMA,16.4*20.

JC64-00248A KEY-M_MENU;SCX-5530FN,ABS,84.2*16.5*15.5

JC64-00249A KEY-M_ON HOOK;SCX-5530FN,ABS,37.8*11.3*7

JC64-00250A KEY-M_ONETOUCH;SCX-5530FN,ABS,72.55*62*1

JC67-00148A LENS LED-M_STATUS;SCX-5530FN,PMMA,MILKY

JC73-00230A RUBBER-MENU;SCX-5530FN,SILICON,85.6*16.6

JC73-00231A RUBBER-ONETOUCH;SCX-5530FN,SILICON,100.3

JC73-00232A RUBBER-TEL_COPY;SCX-5530FN,SILICON,82.2*

JC73-00233A RUBBER-MODE;SCX-5530FN,SILICON,71.2*20.2

Z4391

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SA

SA

SA

SA

SA

SNA

SA

SNA

SNA

SNA

SNA

SNA

SNA

3

Parts List

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

8.9-23

8.10-3

8.10-4

8.10-5

SEC-Code

JC92-01747A

JC96-03919A

4302-001183

JF68-10532B

Description & Specification

PBA SUB-OPE;SCX-5530FN,SEC,-,OPE,-,-,-,3

ELA HOU-ADF;CLX-3160FN/XAA,SEC,-,-,-,-,-

BATTERY-NIH(2ND);3.6V,280MAH,LAY_PLAT.PL

LABEL(P)-BAR CODE;CLP-500,-,YUPO PAPER,1

Location Service

Z4392

Z4544

SA

SA

SA

SNA

8.11-4-17

8.11-4-17

8.11-4-17

8.11-4-18

8.11-5

8.11-5-1

8.11-5-2

8.11-6

8.12-5

8.12-6

8.12-7

8.12-8

8.12-9

8.11-4-9

8.11-4-10

8.11-4-11

8.11-4-12

8.11-4-13

8.11-4-14

8.11-4-15

8.11-4-16

8.11-4-16A

8.11-4-16B

8.11-4-17

8.11-4-17

8.12-10

8.12-11

8.11-3-3

8.11-4

8.11-4-1

8.11-4-2

8.11-4-3

8.11-4-4

8.11-4-5

8.11-4-6

8.11-4-7

8.11-4-8

8.11-4-8A

8.11-4-8B

8.10-6

8.10-7

8.10-7

8.11-1

8.11-2

8.11-3

8.11-3-1

8.11-3-2

8.11-3-2-1

8.11-3-2-2

8.11-3-2-3

8.11-3-2-4

8.11-3-2-5

JC39-00568A CBF HARNESS-PANEL;CLX-3160,WIRE HARNESS,

6502-000121 CABLE CLAMP;DAMC-101,D7~8,L19,SCP-1,NTR

6502-000132 CABLE CLAMP;DAWS-1NE,ID11,L21.0,NTR,NYLO

JC96-03916A ELA HOU-ADF LOWER;CLX-3160FN/XAA,SEC,-,-

JC96-03915A ELA HOU-ADF MOTOR;CLX-3160FN/XAA,SEC,-,-

JC97-02410A MEA-ADF UPPER;SCX-5530FN,SEC,-,-,-,-,-

JC63-00985A COVER-M_ADF UPPER;SCX-5530FN,HIPS,-,188.

JC97-01940B MEA UNIT-HOLDER ADF;SCX-5530FN,-,-,-,-,-

JC61-00893B

JC61-00387A

JC63-00373A

JB73-00052A

JC66-00738A

HOLDER-M_PAD ADF;SCX-5530FN,POM,1.5,44.9

SPRING ETC-PAD;ML-9400W,SUS304WPB,PI0.5,

SHEET-ADF HOLDER;SCX-4920,PC,0.2,18,35.4

RMO-ADF RUBBER;SCX-1110F,SILICON RUBBER,

DAMPER-PAD ADF_R2;SCX-4720F,POLY URETHAN

JC66-00461A ROLLER-M-ADF IDLE;SCX-4114F,POM,-,-,BLK,

JC97-01962C MEA UNIT-PICKUP;SCX-5530FN,-,-,-,-,-,-

JC72-00734A PMO-COVER ADF;SCX-5100,HIPS,WHT,-,-,HB,-

JB66-00103A GEAR-ADF 38;SCX-1110F,POM(DELIN500P),0.6

JC61-00963B STOPPER-M_PICKUP ADF;SCX-5530FN,POM,-,10

JC66-00561A SHAFT-ADF PICKUP;SCX-4216F,SUM22L,-,7,NI

JB70-00168A ICT-PIN ADF;SCX-1110F,STS303,D2.0,-,-,-,

6044-000159 RING-C;ID3,OD7,T0.6,PASS,STSC

JB66-00102A GEAR-PICK UP IDEL 38;SCX-1110F,POM(DELIN

JB75-00300A MEC-PICK UP ROLLER ASSY;SCX-1110F/XRX,XE

JB72-00823A PMO-SLEEVE PICK UP;SCX-1110F,-,POM,BLK,-

JB73-00055A RMO-PICKUP ROLLER;SCX-1110F/XRX,EPDM RUB

JB72-00821A

JB61-70904A

JB72-00817A

JB66-00104A

JC72-00744A

JB66-00105A

JB72-00845A

JB75-00299A

JB73-00054A

JB72-00822A

6031-000023

6031-001577

PMO-ADF COLAR;SCX-1110F,POM,NTR,-,-,-,-,

SPRING ETC-CLUTCH;AMUNDSEN,SWRS82A,D11.4

PMO-ADF CLUTCH;SCX-1110F,POM,WHT,-,-,-,-

GEAR-ADF IDLE 34;SCX-1110F,POM(DELIN500P

PMO-SHAFT PICK UP;SCX-5150,-,ABS,BLK,HB,

GEAR-PICK UP 26;SCX-1110F,POM(DELIN500P)

PMO-PICK UP CLUTCH SUB;SCX-1110F,POM(F20

MEC-ADF ROLLER ASSY;SCX-1110F/XRX,XEROX,

RMO-ADF ROLLER;SCX-1110F/XRX,EPDM RUBBER

PMO-SLEEVE ADF;SCX-1110F,-,POM,BLK,-,-,-

WASHER-PLAIN;-,ID5.9,OD10.0,T0.5,BLK,POL

WASHER-PLAIN;POLY,-,ID5.1,OD14,T0.5,BLK,

6031-001051 WASHER-PLAIN;M4,ID4.1,OD7.0,T0.13,*,POLY

6031-001543 WASHER-PLAIN;POLY,-,ID5.1,OD8,T0.13,-,-

6031-001547 WASHER-PLAIN;POLY,-,ID6.5,OD12,T0.5,-,-

JC66-01099A SHAFT-M-AUGER TONER Y;CLP-300,ABS GF20%

JC97-02411A MEA-COVER OPEN;SCX-5530FN,SEC,-,-,-,-,-

JC63-00983A COVER-M_ADF OPEN;SCX-5530FN,HIPS,-,265.2

JB72-00843A PMO-GUIDE PAPER;SCX-1110F,HIPS,IV21,-,-,

JC63-00998A COVER-M_ADF CONNECTOR;SCX-5530FN,ABS,-,7

JB61-00076A SPRING ETC-TORSION DOC (CC2-F);SCX-1110F

JB72-00819A PMO-BUSH;SCX-1110F,POM,NTR,-,-,-,-,-,-

JC61-00548A SPRING ETC-WHITE BAR;SCX-5312F,SUS304WPB

JC61-00712A GUIDE-STACKER SUB;SCX-4216F,PC+ABS,2.5T,

JC63-00372A GROUND-P-ADF R2;SCX-4920N,C5210P,0.2,8,1

JC63-00982A COVER-M_ADF LOWER;SCX-5530FN,ABS,-,238,1

JC66-00310A GEAR-AGITATOR-2;SCX-5100,POM(M90-44),0.6

SA

Z4538 SNA

C0069 SA

SA

Z4370

Z4371

Z4372

S0028

Z4373

SA

SNA

SA

SA

SA

SA

SNA

SA

SNA

K4221

Z4374

Z4375

Z4376

P2150

I0001

Z4357

Z4377

Z4378

Z4379

SA

SA

SA

SA

SNA

SA

SA

SA

SA

SA

SA

SNA

Z4380

Z4381

Z4382

Z4383

Z4384

Z4385

Z4386

Z4387

Z4388

SNA

SA

SNA

Z4525 SNA

SA

SA

SA

SA

SA

SA

SA

SA

Z4526 SNA

Z4527 SNA

Z4528 SNA

SNA

Z4389 SA

SNA

Z4390

O1013

Z4355

Z4294

Z4353

K3231

SA

SNA

SA

SA

SA

SA

SA

SNA

SNA

4

Parts List

8.14-13

8.14-14

8.14-15

8.14-16

8.14-17

8.14-18

8.14-19

8.14-20

8.14-22

8.14-24

8.14-25

8.14-26

8.14-27

8.14-1

8.14-2

8.14-3

8.14-4

8.14-5

8.14-6

8.14-7

8.14-9

8.14-10

8.14-11

8.14-11

8.14-12

8.14-28

8.14-29

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

8.12-12

8.12-13

8.12-14

8.12-15

SEC-Code

JC66-00460A

JC66-00559A

JC66-00560A

JC70-10467A

Description & Specification

SHAFT-M-FEED GEAR 38;SCX-4216F,POM,-,D5.

ROLLER-EXIT;SCX-4216F,CR+SUM24L,14,-,-,-

ROLLER-DRIVE;SCX-4216F,CR+SUM24L,14,-,-,

IPR-GROUND_ROLLER;SCF-ML,SUS301,-,T0.2,-

Location Service

Z4359

Z4356

Z4358

SA

SA

SA

S1049 SNA

8.13-5

8.13-8

8.13-9

8.13-10

8.13-11

8.13-13

8.13-14

8.13-15

8.13-16

8.13-17

8.13-18

8.13-19

8.12-16

8.12-17

8.12-18

8.12-19

8.12-20

8.12-22

8.12-23

8.12-24

8.13-2

8.13-20

8.13-21

8.13-22

8.13-3

JC72-01010A PMO-ACTUATOR REGI SENSOR;SCX-4216F,PC,BL

JC72-01011A PMO-ACTUATOR SCAN SENSOR;SCX-4216F,PC,BL

JC72-01320A PMO-ACT EMPTY ADF;SCX-4920N,ABS,GRAY,-,-

JC75-00095A MEC-BRUSH ANTISTATIC;ML-6060A,SEC,NTR

JC92-01859A PBA SUB-ADF;CLX-3160,-,-,-,-,-,-,-,-

JC61-01695A BRACKET-P_WHITE_BAR;SCX-5530FN,SECC,T1.0

JC72-00752A PPR-WHITE BAR SHEET;SCX-5100,PET,WHT,T0.

JC39-00187A CBF HARNESS-ADF ROLLER GND;SCX-5100,WIRE

6003-000269

JC66-00556A

JC66-00557A

JC39-00640A

6031-000019

SCREW-TAPTITE;BH,+,-,S,M3,L6,ZPC(YEL),SW

IMPELLER-ADF;SCX-4216F,NYLON66,-,-,-,-,V

GEAR-REMOVE ADF;SCX-4114F,POM,M0.6,Z30,-

HARNESS-ADF GND;CLX-3160,HARNESS,UL 1007

WASHER-PLAIN;-,ID6.1,OD8.5,T0.1,BLK,POLY

6031-001511 WASHER-PLAIN;POLYSLIDE,M5,ID5.2,OD10,T0.

JB66-00101A GEAR-CLUTCH 29;SCX-1110F,POM(DELIN500P),

JB70-00070A IPR-WASHER WAVE;SF-4750C,SUS301,-,0.1T,-

JB72-00844A PMO-WHITE CLUTCH SUB 29;SCX-1110F,POM(F2

JC31-00036A MOTOR STEP-ADF;M42SP-13NK,SCX-4920N,0.6A

JC61-01659A BRACKET-P-GEAR L;CLX-3160FN,SECC,T1.2,W1

JC66-00322A GEAR-CLUTCH 39;SCX-5150,POM,M0.6,Z39,-,W

JC66-00454A LINK-M-SWING ADF;SCX-4216F,DELIN 500CL,-

JC66-00455A GEAR-58/25 ADF;SCX-4216F,POM,M0.6,Z58/25

JC66-00456A GEAR-40/21 ADF;SCX-4216F,POM,M0.6,Z40/21

JC66-00457A GEAR-SWING 31/20 ADF;SCX-4216F,POM,M0.6,

JC66-00458A GEAR-IDLE 35 ADF;SCX-4216F,POM,M0.6,Z35,

Z4362

Z4361

S3071

M0022

SA

SA

SA

SA

Z4354

S5050

H1031

Z4513

SA

SA

SA

SA

Z4369

G0417

SA

SA

SA

SA

Z4629 SNA

JC61-01443A

JC61-40001A

JC66-00050A

JC61-01521A

JC39-00488A

JC39-00565A

6502-001093

JC33-00015C

JC66-01056A

6044-000001

6044-001005

JC66-00346A

FRAME-M BASE GOGH;CLP-300,PC+ABS,NH-1000

FOOT-ML80;ML-80,NBR,-,GRAY,-,-,-

CAM-CATCH;ML-9400W,POM,-,34¡¿18¡¿7,WHITE S

PLATE-P-DRAW CONNECTOR;CLP-300,SECC,T1.0

CBF HARNESS-MAIN_DRAW;CLP-300,WIRE HARNE

CBF HARNESS-ADF_DRAW;CLX-3160,WIRE HARNE

CABLE CLAMP;DAWS-3NE,ID11*L34.8,-,NYLON6

SOLENOID-PICK UP;-,CLP-300,DC24V,48§Ù¡¾1 S

GEAR-REGI DRIVE;CLP-300,POM,M0.8,Z32,-,W

RING-CS;ID3,OD3,T0.25,BLACK,SUS304

RING-CS;ID4.8,OD10.0,T0.25,PASS,SUS-30

GEAR-MP/DUP DRV;SCX-5100,POM,SW-01,M0.8,

JC61-01483A PLATE-P-GROUND LSU;CLP-300,C5210P,T0.2,1

JC61-01485A PLATE-P-GROUND REGI;CLP-300,SUS304 CSP,T

JC61-01547A SPRING ETC-OPC LOCK R;CLP-300,C5210W,D1.

JC61-01484A PLATE-P-GROUND T2;CLP-300,C5210P,T0.2,21

JC61-01537A PLATE-P-SHAFT LACK;CLP-300,SECC,T1.0,4,1

JC61-01482A PLATE-P-GROUND FUSER;CLP-300,SUS304-CSP,

JC61-01489A PLATE-P-GROUND EXIT;CLP-300,SUS 304 CSP,

JC39-00302A CBF HARNESS-100M_GND;CLP-500,-,-,1 PIN,5

JC96-04021A ELA HOU-REGI_EMP_MP;CLX-3160,KOREA,KOREA

JC66-01119A LEVER-M-ACTUATOR EMPTY;CLP-300,PC,T2.5,5

JC61-01481A HOLDER-M-ACTUATOR EMPTY;CLP-300,ABS,T2.5

JC61-00018A SPRING ETC-SENSOR;SF-5100,SUS304WPB,0.2,

JC66-01133A LEVER-M-ACTUATOR FEED;CLP-300,POM,T2.5,3

JC61-01480A HOLDER-M-ACTUATOR FEED;CLP-300,ABS,T2.5,

JC61-01546A SPRING ETC-OPC LOCK L;CLP-300,C5210W,D1.

Z6018

Z6019

Z4364

Z6061

Z4368

Z4367

Z4366

Z4550 SNA

F0003 SA

C0004 SA

Z4566 SNA

Z4477 SA

SA

C0002

Z4448

SA

SA

Z4471 SA

Z4513 SNA

Z4417

G0340

SA

SA

SNA

SA

SA

SA

SA

SNA

SA

SA

SA

SA

SA

SA

Z4554 SNA

Z4556 SNA

Z4470 SA

Z4555 SNA

Z4558 SNA

Z4553 SNA

Z4557 SNA

C0007 SA

SA

Z4578 SNA

Z4577 SNA

Z4567 SNA

Z4545 SNA

Z4568

Z4468

SNA

SA

5

Parts List

8.14-79-1

8.14-79-2

8.14-80

8.14-81

8.15-1

8.15-2

8.15-3

8.15-4

8.15-5

8.15-6

8.15-7

8.15-8

8.15-9

8.14-67-1

8.14-67-2

8.14-67-3

8.14-67-4

8.14-67-5

8.14-68-1

8.14-68-2

8.14-68-5

8.14-69

8.14-73

8.14-74

8.14-75

8.15-10

8.15-11

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

8.14-32

8.14-33

8.14-34

8.14-35

SEC-Code

JC92-01723A

JC61-01451A

JC61-01486A

JC63-00854A

Description & Specification

PBA SUB-WASTE_T;CLP-300,SEC,KOREA,WASTE_

PLATE-P-GROUND OPC L;CLP-300,C5210P,T0.2

PLATE-P-GROUND PICKUP;CLP-300,C5210P,T0.

COVER-M-GROUND OPC;CLP-300,ABS HB,T1.5,

Location Service

Z4474 SA

Z4551 SNA

Z4546 SNA

Z4547 SNA

8.14-55

8.14-56

8.14-58

8.14-58-1

8.14-58-2

8.14-58-3

8.14-59

8.14-60

8.14-61

8.14-62

8.14-64

8.14-67

8.14-36

8.14-37

8.14-38

8.14-39

8.14-41

8.14-42

8.14-44

8.14-45

8.14-50

8.14-51

8.14-52

8.14-53

8.14-54

JC61-01477A FRAME-M-EXIT;CLP-300,PC,NH-1035,5V,BLACK

6107-001163 SPRING-CS;SUS304-WPB,-,PI0.4,D3.9,L13,-,

JC61-01568A HOLDER-M-EXIT F DOWN;CLP-300,PC,T2.5,26.

JC66-01149A ROLLER-EXIT MAIN;CLP-300,PFA,D8.5,L23,BL

JC66-01040A ROLLER-EXIT F DOWN;CLP-300,SUM22/EPDM,D4

JC61-00829A HOLDER-BEARING EXIT F/DOWN;SCX-4216F,POM

JC66-00810A GEAR-EXIT_DRV17;ML-1610,POM,0.8,17,-,BLK

JC97-02639A MEA UNIT-FU TERMINAL;CLP-300,SEC,EXPORT,

JC66-01207A

JC47-00014A

JC61-01566A

JC39-00498A

JC39-00497A

SHAFT-M-CLUTCH FUSER;CLP-300,POM,L39.8,D

MEP-CLUTCH CAM;-,CLP-300,-,DC24V,0.18A,C

HOLDER-M-CLUTCH FUSER;CLP-300,PC+ABS,T2.

CBF HARNESS-COVER S/W;CLP-300,WIRE HARNE

CBF HARNESS-INLET;CLP-300,WIRE HARNESS,U

JC47-00009C MEP-CLUTCH REGI;-,CLP-300,3.0W,DC24V,125

6031-001255 WASHER-PLAIN;NYLON,CUTTING,ID5,OD9,T0.5,

JC97-02688A MEA UNIT-PICK UP GEAR;CLP-300,SEC,WORLD,

JC66-01076A GEAR-PICK UP A;CLP-300,POM,M0.8,Z45,-,WH

JC66-01077A GEAR-PICK UP B;CLP-300,POM,M0.8,Z45,-,WH

6107-001167 SPRING-CS;SUS304-WPB,-,PI0.25,D3.25,L9.6

JC61-01478A GUIDE-M-HARNESS;CLP-300,ABS,HB,T2.5,118.

JC61-70911A SPRING ETC-EXIT ROLL FD;ML-165,SUS304 WP

JC61-01548A HOLDER-M-CAM;CLP-300,POM (DE8903),T2.0,1

JC66-01120A SHAFT-FEED IDLE;CLP-300,SUM22+NI,L237,D8

JC66-01307A ROLLER-REGI;CLX-3160FN,SUM22+EPDM,D6.0/D

JC97-02647A MEA UNIT-PICKUP ROLL;CLP-300,SEC,EXPORT,

Z4569 SNA

Z4460 SA

Z4570 SNA

Z4464 SA

Z4548 SNA

H4009 SA

O1073 SA

SA

Z4472

Z4469

SA

SA

Z4549 SNA

Z4459 SA

Z4458 SA

Z4467

W0004

SA

SA

Z4478

Z4479

Z4318

SA

SA

SA

SA

Z4552 SNA

O1053 SA

Z4559 SNA

Z4560 SNA

SNA

SA

JC66-01080A SHAFT-P-PICKUP;CLP-300,SECC,L286,T1.2,-,

JC66-01105A CAM-M-PICK UP;CLP-300,POM M90-44,-,-,WHI

JC61-01151A HOUSING-M-PICK_U;ML-1610,POM,-,-,35,NATU

JC61-01173A HOUSING-M-PICK_UP B;ML-1610,ABS HB,-,-,3

JC73-00211A RUBBER-PICK_UP;ML-1610,EPDM+IR,MM,-,-,-,

JC61-01473A GUIDE-M-PICK UP;CLP-300,PC+ABS,HB,T2.5,5

JC61-01538A HOLDER-M-PAD;CLP-300,PC+ABS,HB,T2.5,-,-,

JC66-00815A LEVER-M-KICKER P/U;ML-1610,POM,-,10.5,31

JC61-01533A PLATE-P-PICK UP;CLP-300,SECC,T1.0,264,43

JC72-00382B PMO-BUSHING FEED;ML-1710,POM(DERLIN 8903

JC66-00598A ROLLER-FEED;ML-1710,SUM24L+NI+EPDN,5/12.

JC66-01213A SHAFT-M-FEED;CLX-3160FN,POM,L46.7,D10,WH

JC66-01212A GEAR-FEED;CLX-3160FN,POM,M0.8,Z16,-,-,-,

JC61-01667A BUSH-M CLUTCH;CLX-3160FN,POM,ID6.0,OD12.

JC97-02685A MEA UNIT-MP;CLX-3160FN,SEC,WORLD,-,-,-,-

JC63-01147A SHEET-MANUAL;CLX-3160FN,PET,T0.188,W217,

JC61-01450A BRACKET-P-DRIVE MOTOR;CLP-300,SECC,T1.2,

6031-001528 WASHER-PLAIN;POLYMIDE,-,ID6,OD13.5,T0.5,

JC66-01042A GEAR-IDLE DEVE Z19;CLP-300,POM,M0.8,Z19,

JC66-01052A GEAR-RDCN DEVE CAM;CLP-300,POM,M0.8/M0.6

JC66-01041A GEAR-DEVE COUPLING;CLP-300,POM,M0.8,Z18,

6107-001271 SPRING-CS;SUS304 WPB,-,PI0.55,D6.75,L9.0

JC66-01047A GEAR-IDLE Z39;CLP-300,POM,M0.8,Z39,-,WHI

JC66-01065A GEAR-TONER DRIVE;CLP-300,POM,M0.8/Z0.8,Z

JC66-01046A GEAR-IDLE Z33;CLP-300,POM,M0.8,Z33,-,WHI

JC66-00763A GEAR-M-PICK UP IDLE;CLP-600,POM,M0.8,SPU

JC47-00007E MEP-CLUTCH CAM;-,CLP-300,-,DC24V,0.133A,

Z4575 SNA

Z4576 SNA

P2067

P2068

SA

SA

P2148 SA

Z4571 SNA

Z4573 SNA

R1120 SA

Z4572 SNA

O1102 SA

F6200 SA

SNA

SNA

SNA

SA

SA

Z4524 SNA

Z4422 SA

Z4423

Z4424

SA

SA

Z4425

Z4426

Z4427

Z4428

Z4429

SA

SA

SA

SA

SA

G0031

Z4430

SA

SA

6

Parts List

8.15-51

8.16-1

8.16-2

8.16-3

8.16-4

8.16-5

8.16-6

8.17-4

8.17-5

8.17-7

8.17-9

8.17-10

8.17-11

8.15-44

8.15-45

8.15-46

8.15-47

8.15-48

8.15-49

8.15-51

8.15-51

8.15-51

8.15-51

8.15-51

8.15-51

8.17-12

8.17-14

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

8.15-12

8.15-13

8.15-14

8.15-15

SEC-Code

JC66-01208A

JC66-01045A

JC66-01048A

JC66-01054A

Description & Specification

GEAR-RDCN FUSER CAM;CLP-300,POM,M0.8/Z0.

GEAR-IDLE ITB Z43;CLP-300,POM,M0.5,Z43,-

GEAR-ITB DRIVE;CLP-300,POM,M0.5/M0.5,Z10

GEAR-RDCN OPC;CLP-300,POM,M0.5/M0.6,Z79/

Location Service

Z4431

Z4432

Z4433

Z4434

SA

SA

SA

SA

8.15-30

8.15-32

8.15-32

8.15-32

8.15-33

8.15-34

8.15-35

8.15-36

8.15-37

8.15-38

8.15-41

8.15-43

8.15-16

8.15-17

8.15-18

8.15-19

8.15-20

8.15-21

8.15-22

8.15-24

8.15-25

8.15-26

8.15-27

8.15-28

8.15-29

JC66-01049A GEAR-OPC DRIVE;CLP-300,POM,M0.6/M0.6,Z53

JC66-01051A GEAR-RDCN DEVE;CLP-300,POM,M0.5/M0.8,Z73

JC66-01055A GEAR-RDCN P_PATH;CLP-300,POM,M0.5/M0.8,Z

JC66-01050A GEAR-PICK UP DRIVE;CLP-300,POM,M0.8/M0.8

JC66-01044A GEAR-FUSER DRIVE 1;CLP-300,POM,M0.8,Z45,

JC66-01053A GEAR-RDCN EXIT;CLP-300,POM,M0.8/M0.8,Z51

JC66-01043A GEAR-DEVE DRIVE;CLP-300,POM,M0.6,Z21,-,W

JC66-00771A GEAR-_M_IDLE PICKUP;CLP-600,POM,M0.8,SPU

JC61-01459A

JC66-01061A

JC66-01064A

6003-000301

JC66-01060A

BRACKET-M-DRIVE FRONT;CLP-300,PC,T2.5,W1

SHAFT-IDLE D8;CLP-300,SUM24L+NI,L16.7,D1

GEAR-IDLE Z37;CLP-300,POM,M0.8,Z37,-,WHI

SCREW-TAPTITE;BH,+,S,M4,L6,ZPC(YEL),SWRC

SHAFT-WORM GEAR;CLP-300,SUM24L+NI,L44.6,

JC66-01057A GEAR-WORM DEVE CAM;CLP-300,POM,M0.6/M0.6

6001-000130 SCREW-MACHINE;BH,+,M3,L6,ZPC(WHT),SWRCH1

6001-000485 SCREW-MACHINE;PH,+,M2.6,L4,ZPC(YEL),SWRC

6006-000127 SCREW-MACHINE;WS,PH,+,M3,L6,ZPC(YEL),SWR

JC66-01070A LATCH-M-HUB CLUTCH;CLP-300,POM,T2.0,D18.

JC66-01155A GEAR-FUSER RDCN OUT V;ML-3560,HTNFR52G30

6044-000231 RING-E;ID5.0,OD11.0,T0.6,PASS,STS304

JC66-01068A SHAFT-M-T2 CAM;CLP-300,POM,L52,D20,BLACK

JC66-01067A SHAFT-M-ITB CLEAN CAM;CLP-300,POM,L44,D2

JC31-00041A MOTOR DC-DEVE DRIVE;50M843A152,CLP-600,2

JC61-01458A BRACKET-M-DEVE CAM;CLP-300,PC+ABS,T2.5,W

JC67-00130A CAP-M-PUSH COUPLING;CLP-300,POM,T2.0,D13

Z4435

Z4436

Z4437

Z4438

Z4439

Z4440

G0010

SA

SA

SA

SA

SA

SA

SA

SA

Z4530 SNA

Z4531 SNA

Z4441 SA

Z4532 SNA

Z4533 SNA

Z4444

Z4445

SA

SA

Z4534 SNA

Z4563 SNA

Z4535 SNA

Z4536 SNA

R0006

Z4446

SA

SA

Z4447

M0024

SA

SA

Z4537 SNA

Z4450 SA

JC97-01788B MEA UNIT-CLUTCH DEV;CLP-300,-,WORLD,M0.6

JC66-01066A SHAFT-M-DEVE CAM;CLP-300,POM,L116,D18.3,

JC92-01720A PBA SUB-DEVE_HOME;CLP-300,SEC,KOREA,DEVE

JC61-01453A HOLDER-M-LINK BLACK;CLP-300,PC+ABS,T2.5,

JC66-01097A LINK-M-PUSH BLACK CAP;CLP-300,POM,22,T2.

JC61-00699A BUSH-D6/L4;CLP-500,BRONZE+ST,ID6.0,OD9.0

0205-001095 GREASE-BEARING;NYE8512,NOISE DAMPING(BLU

0205-001003 GREASE-BEARING;NYOGEL788,DAMPING GREASE,

0205-001059 GREASE-BEARING;PETAMO GHV 133,BEIGE,15KG

0205-001144 GREASE-BEARING;SF-112,HANARL,NOISE TAMPI

0205-001080 GREASE-BEARING;NYOGEL 774H,NOISE DAMPING

0205-001002 GREASE-BEARING;NYOGEL744,WITH PTFE,-

0205-000005 GREASE-BEARING;EP56,DIAMOND HYDRO FLUID,

JC67-00168A BRUSH-LSU;CLP-300,PP BRUSH,-,W4.5,L180.6

JC64-00267A SHUTTER-LSU;CLP-300,ABS GF20,T2.5,W11.5,

JC63-00839A COVER-M-LSU;CLP-300,ABS HB,T2.0,239.5,1

6107-001295 SPRING-CS;SUS304,-,PI0.45,D5.45,L22.5,-,

JC63-01093A SHEET-LSU FRONT;CLP-300,PET SHEET,T0.188

JC62-00338A SEAL-COVER LSU;CLP-300,EPDM,-,T2.5,W8,L1

0604-001257 PHOTO-INTERRUPTER;TR,-,-,DIP-4,BK

6003-000282 SCREW-TAPTITE;BH,+,-,B,M3,L8,ZPC(BLK),SW

6107-001287 SPRING-CS;SUS304-WPB,-,PI0.6,D6.5,L25,-,

6107-001289 SPRING-CS;SUS304-WPB,-,PI0.95,-,L21.2,-,

JC02-00054A TONER-BLACK;CLP-300,SAK-79JG-K1,BLACK,8.

JC39-00489A CBF HARNESS-ITB_JOINT;CLP-300,WIRE HARNE

JC39-00502A CBF HARNESS-ITB_HOME;CLP-300,WIRE HARNES

JC61-01494A FRAME-M-ITB;CLP-300,ABS+GF20%,GR-4020,-,

Z4451

Z4452

Z4453

Z4454

SA

SA

SA

SA

Z4455

B0027

SA

SA

Z4543 SNA

Z4539 SNA

Z4540 SNA

Z4541 SNA

Z4542 SNA

SNA

SNA

Z4579 SNA

Z4580 SNA

Z4581 SNA

Z4582 SNA

Z4583 SNA

Z4584 SNA

Z4628 SNA

Z4517 SA

Z4630 SNA

Z4632 SNA

Z4633 SNA

Z4634 SNA

Z4635 SNA

Z4636 SNA

7

Parts List

8.17-57

8.17-58

8.17-59

8.17-60

8.17-61

8.17-62

8.17-63

8.17-64

8.17-71

8.17-75

8.17-81

8.17-85

8.18-2

8.17-44

8.17-45

8.17-46

8.17-47

8.17-48

8.17-49

8.17-50

8.17-52

8.17-53

8.17-54

8.17-55

8.17-56

8.18-4

8.18-6

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

8.17-15

8.17-16

8.17-17

8.17-18

SEC-Code

JC61-01495A

JC61-01497A

JC61-01498A

JC61-01499A

Description & Specification

FRAME-M-WASTE ITB;CLP-300,ABS GF20%,GR-4

HOUSING-M-CLEANING ITB;CLP-300,ABS GF 20

HOLDER-M-BUSH CHARGE;CLP-300,POM(M90-44)

GUIDE-M-POLE ITB;CLP-300,ABS HF-0660I,-,

Location Service

Z4637

Z4638

Z4639

Z4640

SNA

SNA

SNA

SNA

8.17-32

8.17-33

8.17-34

8.17-35

8.17-36

8.17-37

8.17-38

8.17-39

8.17-40

8.17-41

8.17-42

8.17-43

8.17-19

8.17-20

8.17-21

8.17-22

8.17-23

8.17-24

8.17-25

8.17-26

8.17-27

8.17-28

8.17-29

8.17-30

8.17-31

JC61-01502A BRACKET-P-HOUSING LEFT;CLP-300,SECC,1.2T

JC61-01503A BRACKET-P-HOUSING RIGHT;CLP-300,SECC,1.2

JC61-01504A PLATE-P-GND ITB;CLP-300,BRONZE(C5210P-H)

JC61-01505A HOLDER-M-PTL;CLP-300,ABS HB HF-0660I,10.

JC61-01506A HOLDER-M-HOME SENSOR;CLP-300,ABS HB(HF-0

JC61-01536A BUSH-M-CHARGE CLEANING;CLP-300,POM(M90-4

JC61-01539A BUSH-M-DRIVE ITB;CLP-300,POM(M90-44),ID6

JC61-01540A BUSH-M-ITB;CLP-300,POM(M90-44),ID6,OD8.1

JC61-01541A

JC61-01542A

JC61-01543A

JC61-01701A

JC61-01704A

BUSH-M-TR ITB;CLP-300,POM(AT-15CF),ID6,-

BUSH-M-IDLER WASTE BELT;CLP-300,POM(M90-

BUSH-CHARGE LEFT;CLP-300,SINTERED BRONZE

SPRING ETC-SHUTTER;CLP-300,SWP-B,¡Ë0.35,S

SPRING ETC-GROUND ITB;CLP-300,SUS304-WPB

JC62-00210A SEAL-AUGER OPC;CLP-300,PORON LE-20,-,5T,

JC62-00212A SEAL-BELT ITB;CLP-300,URETHANE FILM,-,0.

JC62-00213A SEAL-LOW ITB;CLP-300,POLYURETHANE,-,6T,W

JC62-00217A SEAL-COVER WASTE;CLP-300,PORON,-,T2,W11.

JC62-00219A SEAL-BACK ITB;CLP-300,POLYURETHANE FOAM,

JC62-00221A SEAL-BACK ITB RIGHT;CLP-300,POLYURETHANE

JC62-00222A SEAL-SIDE ITB LEFT;CLP-300,POLYURETHANE

JC62-00223A SEAL-SIDE ITB RIGHT;CLP-300,POLYURETHANE

JC62-00229A SEAL-BLADE ITB LEFT;CLP-300,POLYURETHANE

JC62-00232A SEAL-TOP ITB;CLP-300,POLYURETHANE,-,10T,

JC62-00257A SEAL-FRAME WASTE ITB;CLP-300,PORON LE-20

JC62-00258A SEAL-WASTE OPC;CLP-300,PORON LE-20,-,T0.

Z4641 SNA

Z4642 SNA

Z4643 SNA

Z4644 SNA

Z4645 SNA

Z4646 SNA

Z4647 SNA

Z4648 SNA

Z4649 SNA

Z4650 SNA

Z4651 SNA

Z4652 SNA

Z4653 SNA

Z4654 SNA

Z4655 SNA

Z4656 SNA

Z4657 SNA

Z4658 SNA

Z4659 SNA

Z4660 SNA

Z4661 SNA

Z4662 SNA

Z4663 SNA

Z4664 SNA

Z4665 SNA

JC62-00281A SEAL-HOUSING ITB L;CLP-300,PORON LE-20,B

JC62-00282A SEAL-HOUSING ITB R;CLP-300,PORON LE-20,B

JC62-00326A SEAL-WASTE SIDE;CLP-300,POLY URETHANE FO

JC63-00857A COVER-M-WASTE ITB;CLP-300,PC,2.0T,W49.4,

JC63-00859A COVER-M-WASTE EXIT;CLP-300,POM(M90-44),T

JC63-00862A COVER-M-HANDLE ITB;CLP-300,ABS HF-0660I,

JC63-01045A SHEET-FRAME ITB;CLP-300,PC,T0.125,W80.5,

JC63-01124A SHEET-HOUSING ITB F;CLP-300,PET,T0.188,W

JC63-01170A SHEET-BLADE ITB;CLP-300,PC,T0.5,5,222.5,

JC66-01082A ARM-M-BLADE ITB;CLP-300,PC,T5.0,53,L71,B

JC66-01083A SHAFT-M-BELT WASTE;CLP-300,POM(M90-44),L

JC66-01085A SHAFT-M-AUGER ITB;CLP-300,ABS+GF20%,253,

JC66-01087A GEAR-AUGER ITB;CLP-300,POM (M90-44),M0.8

JC66-01112A DRUM-ITB BELT;CLP-300,PI,OD120,W240,L376

JC66-01131A ROLLER-T1;CLP-300,NBR + ECO FORM,OD14,L2

JC67-00027A LENS-PTL;ML-1710,PMMA,NTR,-,-,-,-

JC68-10914D LABEL(P)-SERIAL NO;ML-85,ART,70X15,G100,

JC72-40332A PMO-BUSHING_CHARGE;ML-80,POM,BLK,HB,-

JC73-00222A RUBBER-BELT WASTE ITB;CLP-300,CR+NR20%,1

JC92-01709A PBA SUB-ITB_JOINT;CLP-300,SEC,KOREA,ITB-

JC92-01724A PBA SUB-PTL;CLP-300,SEC,KOREA,PTL,-,-,-,

JC97-02645A MEA UNIT-BLADE ITB;CLP-300,SEC,EXPORT,-,

JC97-02646A MEA UNIT-ROLL DRV ITB;CLP-300,SEC,EXPORT

JC97-02695A MEA UNIT-ROLL IDL ITB;CLP-300,SEC,WORLD,

6006-001078 SCREW-TAPTITE;WSP,PH,+,M3,L10,ZPC(YEL),S

JC39-00499A CBF HARNESS-JOIN_DRAW;CLP-300,WIRE HARNE

JC67-00199A CAP-DEVE;CLP-300,PP,-,31.5,62,-,-

Z4666 SNA

Z4667 SNA

Z4668 SNA

Z4669 SNA

Z4670 SNA

Z4671 SNA

Z4672 SNA

Z4673 SNA

Z4674 SNA

Z4675 SNA

Z4676 SNA

Z4677 SNA

Z4678 SNA

Z4679 SNA

Z4680 SNA

K3433 SA

Z4619 SNA

Z4681 SNA

Z4682 SNA

Z4683 SNA

Z4684 SNA

Z4685 SNA

Z4686 SNA

Z4687 SNA

Z4613 SNA

Z4614 SNA

Z4616 SNA

8

Parts List

8.19-16

8.19-17

8.19-18

8.19-19

8.19-20

8.19-21

8.19-22

8.19-23

8.19-24

8.19-25

8.19-28

8.19-29

8.19-30

8.19-4

8.19-5

8.19-6

8.19-7

8.19-8

8.19-9

8.19-10

8.19-11

8.19-12

8.19-13

8.19-14

8.19-15

8.19-31

8.19-32

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

8.18-7

8.18-9

8.18-10

8.18-10-1

SEC-Code

JC68-01708A

JC69-01013A

JC96-03911A

JC61-01520A

Description & Specification

LABEL-INFORMATION;CLP-300,-,WHITE POLY,T

CUSHION-DEVE;CLP-300,EPP,T10,W75,L351,-,

ELA UNIT-DEV MAIN SET;CLP-300,SEC,EXPORT

FRAME-M-DEVE MAIN;CLP-300,ABS GF20%,GR-4

Location Service

Z4617

Z4620

Z4621

SNA

SNA

SNA

SNA

8.18-10-2

8.18-10-3

8.18-10-4

8.18-10-5

8.18-10-6

8.18-10-7

8.18-10-8

8.18-10-9

8.18-10-12

8.18-10-13

8.18-10-14

8.18-10-16

8.18-10-17

8.18-10-18

8.18-10-19

8.18-10-20

8.18-10-21

8.18-10-22

8.18-10-25

8.18-10-27

8.18.10-29

8.18-11

8.19-1

8.19-2

8.19-3

JC63-00853A COVER-M-TONER BOTTLE;CLP-300,ABS HB HF-0

JC92-01708A PBA SUB-DEVE_JOINT;CLP-300,SEC,KOREA,DEV

JC66-01115A GEAR-WORM AGITATOR;CLP-300,PC-141R,-,-,-

JC97-01788C MEA UNIT-CLUTCH TONER;CLP-300,-,WORLD,M0

JC66-01116A GEAR-IDLE M08Z30L;CLP-300,POM (M90-44),M

6107-001285 SPRING-CS;SUS304-WPB,-,PI0.45,D8.85,L12,

6107-001292 SPRING-CS;SUS304-WPB,-,PI0.55,-,L11.1,-,

JC33-00018A SOLENOID-TONER;-,CLP-300,DC24V,120§Ù¡¾10SN

JC61-01573A

JC61-01687A

JC61-01706A

JC63-00897A

JC64-00217A

HOLDER-SUPPORT;CLP-300,ABS,T14.5,W26.5,L

SPRING ETC-LOCK;CLP-300,PW-2,PI1.3,-,-,L

STUD-GEAR ITB;CLP-300,SUM22L,-,-,-,-,OD6

COVER-M-WIRE;CLP-300,ABS,T2.0,W18.9,L133

HANDLE-M-UNIT;CLP-300,ABS,7.0T,50.5,130,

JC64-00229A HANDLE-LOCK;CLP-300,ABS,T34.26,W39.3,L83

JC66-01094A LEVER-M-WASTE SENSOR;CLP-300,ABS,3.0T,18

JC66-01103A LEVER-M-LOCK DEVE FRAME;CLP-300,ABS,2.0T

JC66-01113A GEAR-IDLE M08Z30R;CLP-300,POM (M90-44),M

JC66-01114A GEAR-DRIVE Z20;CLP-300,POM (DE588P),M0.8

JC66-01117A GEAR-IDLE ITB;CLP-300,POM (M90-44),M0.8,

JC66-01143A ROLLER-SLIDE B;CLP-300,POM,L20,OD14,BLAC

JC67-00191A CAP-DUMMY;CLP-300,ABS,-,-,L31.4,DM GRAY,

JC97-02571A MEA UNIT-OPC SET;CLP-300,SEC,WORLD,-,-,-

JC61-01474A FRAME-M-UPPER FUSER;CLP-300,PET+GF30%,BN

JC61-01475A FRAME-M-LOWER FUSER;CLP-300,PET+GF30%,BN

JC66-01078A ROLLER-HEAT;CLP-300,AL5052+RUBBER,D27.5,

SNA

SNA

SNA

SNA

SNA

Z4508 SNA

Z4509 SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

Z4622 SNA

Z4585 SNA

Z4586 SNA

Z4587 SNA

JC66-00669A GEAR-FUSER;SCX-5315F,PPS, OFL4036,1,34,P

JC66-10902A BEARING-H/R L;ML-165,PPS(RBA313N),-,ID26

JC72-00814A PMO-BEARING H/R-F;SCX-5100,-,PPS,BLK,V0,

4712-001027 THERMOSTAT;125/250VAC,15/7.5A,170+-5C,0C

JC66-01079A ROLLER-PRESSURE;CLP-300,SUM22,D16,L237.5

JC66-01111A ROLLER-PRESSURE SHAFT;CLP-300,SUM22,D8.0

JC61-01490A HOLDER-M-BUSH 2PR_R;CLP-300,PBT,T2.0,33.

JC61-01491A HOLDER-M-BUSH 2PR_L;CLP-300,PBT,T2.0,33.

JC61-01534A BUSH-M-2PR L;CLP-300,PPS(RBA313N),-,-,5.

JC61-01535A BUSH-M-2PR R;CLP-300,PPS(RBA313N),-,5.3,

JC61-01522A GUIDE-M-INPUT FUSER;CLP-300,PET+GF30%,5V

JC66-01222A LEVER-M ACTUATOR EXIT;CLX-3160FN,PET+GF3

JC61-01476A PLATE-P-GROUND FUSER;CLP-300,SUS 304 CSP

JC70-00518A ELECTRODE-P-AC R;CLP-300,C5210P T0.8,D3.

JC70-00519A ELECTRODE-P-AC L;CLP-300,C5210P T0.8,D3.

JC68-00408A LABEL(R)-LV FUSER;COMMON,PVC,-,110V,-,,,

JC68-01134A LABEL(P)-BLANK(FUSER);ML-1710D3,-,WHITE

JC68-01581A LABEL(P)-CAUTION HOT;COMMON,SAMSUNG,PET,

6107-001246 SPRING-CS;SWP-B,-,PI0.9,D5.6,L16.6,-,-,I

JC61-01271A SPRING ETC-ACTUATOR;CLP-600,SUS304 ,0.35

JC39-00500A CBF HARNESS-FUSE_LINK1;CLP-300,WIRE HARN

JC39-00501A CBF HARNESS-FUSE_LINK2;CLP-300,WIRE HARN

4713-001209 LAMP-HALOGEN;115V,-,850W,-,-,-,10X299.6M

1404-001368 THERMISTOR-NTC ASSY;1KOHM,-,4537K,0.25MW

JC70-00064A IPR-PIN ROLLER EXIT;SF-5100,SUS304,PI1.8

JC72-20902A PEX-ROLLER F/UP(2);ML-5000A,TEFLON,WHT,-

JC72-00382A PMO-BUSHING TX;ML-6060A,POM M9044,BLK,-,

Z4481

B1019

B1040

T0002

SA

SA

SA

SA

Z4588 SNA

Z4589 SNA

Z4590 SNA

Z4591 SNA

Z4592 SNA

Z4593 SNA

Z4594 SNA

SNA

Z4596 SNA

Z4597 SNA

Z4598 SNA

Z4599 SNA

Z4600 SNA

Z4601 SNA

Z4602 SNA

S0018 SA

Z4483

Z4484

Z4604

Z4486

SA

SA

SA

SA

Z4605 SNA

O1106 SA

Z4606 SNA

9

Parts List

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

8.19-33

8.19-34

8.19-35

8.19-36

SEC-Code

JC66-01206A

JC61-01647A

JC66-01147A

JC66-01148A

Description & Specification

SHAFT-M-CAM FUSER;CLP-300,PC+GF30%,L252.

HOLDER-M-SHAFT FUSER;CLP-300,PC,T2.0,-,L

LEVER-M-RELEASE;CLP-300,PET+GF30%,T1.5,W

LEVER-M-LINK FUSER;CLP-300,PET+GF30%,T1.

Location Service

Z4607

Z4608

Z4609

Z4487

SNA

SNA

SNA

SA

8.20-13

8.20-14

8.20-15

8.20-16

8.20-17

8.20-18

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

8.19-37

8.19-39

8.19-40

8.19-41

8.19-42

8.20-1

8.20-2

8.20-4

8.20-5

8.20-8

8.20-9

8.20-10

8.20-12

JC66-01309A ROLLER-DUMMY;CLP-300,PFA,OD6.0,L10.0,-,-

JC61-01679A SPRING ETC-GROUND;CLP-300,SUS 304 WPB,¥Õ

6107-001267 SPRING-CS;SWP-B,-,PI1.0,D5.9,L17,-,-,ID4

6107-001290 SPRING-CS;SUS304 WPB,-,PI0.55,D5.55,L16,

JC97-02778A MEA UNIT-GUIDE PR;CLP-300,SEC,EXPORT,-,-

JC63-00869A TRAY-M-EXTENSION SMALL;CLP-300,ABS,T2.5,

JC63-00855A COVER-M-CASSETTE;CLP-300,ABS,T2.5,77,224

JC61-01531A STOPPER-M-PAPER REAR;CLP-300,ABS HB,T2.5

JC63-00872A

JC61-01530A

JC70-00516A

JC70-00517A

JC68-01680A

TRAY-M-EXT CASSETTE;CLP-300,ABS,T2.5,118

FRAME-M-SEMI CASSETTE;CLP-300,ABS,HF-066

ADJUST-M-CASSETTE R;CLP-300,ABS HB,T2.5,

ADJUST-M-CASSETTE L;CLP-300,ABS HB,T2.5,

LABEL-INSTRUCTION;CLP-300,-,WHITE PET,T0

JC68-01679A LABEL-INSTRUCTION;CLP-300,-,WHITE PET,T0

6107-001240 SPRING-CS;SUS304-WPB,GROUND END,PI0.6,D1

JC64-00223A LOCKER-M-KNOCK UP L;CLP-300,POM (M90-44)

JC64-00222A LOCKER-M-KNOCK UP R;CLP-300,POM (M90-44)

JG61-70531A SPRING ETC-LOCKER,PLATE;SF6000,STS304WPB

JC61-01158A PLATE-M-KNOCK_UP;ML-1610,HIPS HB,T2,W80,

JC68-00761A MANUAL-PRC;COMMON,SEA,ENGLISH,USA,MOJO 1

JC68-01706A MANUAL-INSTALL;CLX-3160,-,-,-,M150,420 M

JC96-03613A ELA UNIT-TONER TANK Y;CLP-300,SEC,EXPORT

JC96-03614A ELA UNIT-TONER TANK M;CLP-300,SEC,EXPORT

JC96-03615A ELA UNIT-TONER TANK C;CLP-300,SEC,EXPORT

JC96-03616A ELA UNIT-TONER TANK K;CLP-300,SEC,EXPORT

Z4612 SNA

Z4490 SA

Z4482

Z4488

SA

SA

Z4611 SNA

Z4689 SNA

Z4690 SA

SNA

SNA

Z4688 SNA

Z4494

Z4495

SA

SA

Z4692 SNA

Z4691 SNA

D4084 SA

Z4493

Z4492

SA

SA

S0025

K5002

SA

SA

SNA

SNA

Z4499 SNA

Z4498 SNA

Z4497 SNA

Z4500 SNA

JC96-04086A ELA UNIT-ENGINE;CLX-3160FN,SEC,WORLD,-,-

JC99-01962A INA-ACCESSORY;CLX-3160FN,SEC,XAA,IRIS,FA

JC99-01964A PAA-LABEL;CLX-3160FN,XAA,-,-,-,-

JC99-01966A PAA WOOD-PACKING;CLX-3160FN,XAA,-,-,-,-

0202-001240 SOLDER-WIRE;HSE-01,-,D3,SN/0.5CU/0.03NI/

0202-001492 SOLDER-WIRE FLUX;HSE-02 LFM48 SR-34 S,-,

0203-000007 TAPE-FILAMENT;3M,T0.15,W18,L55M,TRP

0203-001100 TAPE-OPP MASKING;OPP/W75/CLR,T0.05,W75,L

0203-001159 TAPE-FILAMENT;#8915,T0.15,W12,L55000,CLR

0204-000469 THINNER;#4662,-,0.795,-

0204-002978 FLUX;KSP-70M,-,84%,FLUX,SPRAY

0205-001056 GREASE-GRAPHITE;CRS841,WHT,-

0205-001067 GREASE-GRAPHITE;NYOGEL 756G,HYDRO CARBON

0205-001214 GREASE;LUBTECH FF 662,WHITE,-

1103-001273 IC-EEPROM;24C64A,64Kbit,8Kx8Bit,DIP,8P,9

2201-002127 C-CERAMIC,DISC;0.47NF,10%,250V,Y5P,TP,8.

2305-000385 C-FILM,LEAD-PEF;470nF,10%,250V,BK,18x6x1

2801-003886 CRYSTAL-UNIT;12MHz,50ppm,28-AAA,16pF,50o

2801-003960 CRYSTAL-UNIT;28.224MHz,50ppm,28-AAA,18pF

2801-004414 CRYSTAL-UNIT;25MHZ,50PPM,HC-49/S,12PF,50

3501-000203 RELAY-MINIATURE;5V,200MW,1000MA,1FORMC,6

3704-000349 SOCKET-IC;8P,DIP,SN,2.54MM

3708-001058 CONNECTOR-FPC/FFC/PIC;30P,1MM,STRAIGHT,S

3708-001637 CONNECTOR-FPC/FFC/PIC;24P,1MM,STRAIGHT,S

3711-000164 HEADER-BOARD TO CABLE;1WALL,2P,1R,2.5mm,

3711-000198 HEADER-BOARD TO CABLE;1WALL,3P,1R,2.5MM,

3711-000203 HEADER-BOARD TO CABLE;1WALL,2P/3P,1R,7.9

SNA

SNA

SA

SNA

SA

SNA

SA

SNA

SA

SNA

SA

SA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SA

SA

10

Parts List

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

#N/A

#N/A

#N/A

#N/A

SEC-Code

3711-002410

3711-003035

3711-004556

3722-002303

Description & Specification

HEADER-BOARD TO CABLE;BOX,10P,2R,2mm,STR

HEADER-BOARD TO CABLE;BOX,14P,2R,2mm,STR

CONNECTOR-HEADER;BOX,8P,2R,2mm,STRAIGHT,

JACK-USB;4P/1C,AU30U,BLK,ANGLE,B TYPE

Location Service

SNA

SA

SNA

SA

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

3722-002345 JACK-MODULAR;6P/4C,INVERTED,N,ANGLE,N,GR

3722-002381 JACK-MODULAR;8P/8C,INVERTED,Y,ANGLE,GRN/

6501-000004 CABLE TIE;DA-80,T1,W2.5,L80,NTR,NYLON66

6602-001528 BELT-FLAT RUBBER;-,CR,T2.5,-,PI69.6,BLAC

6902-000288 BAG PE;LDPE,T0.05,W250,L450,TRP,8,2-

6902-000732 BAG PE;LDPE,T0.1,W120,L200,TRP,0,0,-

6902-000734 BAG PE;LDPE,T0.1,W140,L250,TRP,-,-,-

6902-000786 BAG PE;HDPE,T0.02,W800,L1300,TRP,28,0,M-

JB27-00004A

JB68-00073A

JB68-00916A

JC02-00052A

JC02-00053A

COIL CHOKE-DIP;DR 8X11(470UH),MJC-1450,4

LABEL(R)-BAR CODE;SF-3000,PY,38X6.5,T0.1

LABEL RATING-BLANK;SF-340,SEC,TETRON,0.0

TONER-MAGENTA;CLP-300,SAM-79GZ-K1,MAGENT

TONER-CYAN;CLP-300,SAC-79GZ-K1,CYAN,8.5?

JC02-00055A TONER-YELLOW;CLP-300,SAY-79GZ-K1,YELLOW,

JC39-00578A CBF HARNESS-GND_BRK;CLP-300,WIRE HARNESS

JC39-00579A CBF HARNESS-LSU_S/W;CLP-300,WIRE HARNESS

JC39-00581A CBF HARNESS-FUSER_AC;CLP-300,WIRE HARNES

JC39-00583A HARNESS-GND_FRAME;CLP-300,WIRE HARNESS,U

JC39-00606A HARNESS-SCF;CLX-3160,HARNESS,UL1061,8/8P

JC44-00135A HVPS;-,24V,21.6V~27.6V,-,MAX 5KV,MAX-2KV

JC46-00255A S/W APPLICATION-CD;-,ML-3560,-,PRT DRV,1

JC46-00275A S/W APPLICATION-CD;-,CLX-3160,PRT DRV,1.

JC61-01487A PLATE-P-GROUND SCF;CLP-300,SUS 304 CSP,T

JC61-01570A GUIDE-M-PAPER;CLP-300,POM M90-44,T2.0,15

JC61-01675A SPRING ETC-AUGER;CLP-300,SUS304,¡Ë1.2,-,S

K2756

Z6017

Z4461

Z4463

Z4465

Z4466

SNA

SA

SA

SA

SA

SA

SA

SNA

SNA

SNA

Z4574 SNA

SNA

SA

SNA

SA

SA

SNA

SNA

SNA

SNA

SA

SNA

SNA

SNA

SNA

JC61-01676A SPRING ETC-AUGER K;CLP-300,SWP-B,¡Ë1.2,IS

JC61-01677A SPRING ETC-RETURN;CLP-300,SUS304,¡Ë0.65,S

JC61-01685A SPRING ETC-DUMMY;CLP-600,SUS,0.5,-,-,20.

JC61-01777A HOLDER-BLADE ITB;CLP-300,PC,-,W10,L17.2,

JC61-70940A SPRING ETC-TR(12);ML-5500,-,4.5,-,12.7,1

JC62-00227A SEAL-SHUTTER BOTTLE;CLP-300,POLYURETHANE

JC62-00237A SEAL-AGITATOR BOTTLE;CLP-300,PORON,BLACK

JC62-00259A SEAL-BOTTLE AUGER;CLP-300,PORON LE-20,-,

JC62-00261A SEAL-SHUTTER A;CLP-300,PE FOAM,-,T10,ID3

JC63-00864A SHIELD-P-SMPS;CLP-300,SECC,T1.0,109.7,19

JC63-00894A COVER-INNER;CLP-300,ABS,T2.0,PI 56,-,HB,

JC63-00895A COVER-INNER BK;CLP-300,ABS,T2.0,R75,-,HB

JC63-01046A SHEET-AGITATOR;CLP-300,PET,T0.125,W25.5,

JC63-01047A SHEET-AGITATOR BK;CLP-300,PET,T0.125,W35

JC63-01049A SHEET-HOUSING ITB;CLP-300,PET FILM,T0.18

JC63-01110A SHEET-BRACKET ITB;CLP-300,PET FILM,T0.18

JC63-01149A SHEET-REGI;CLX-3160FN,PC,T0.5,W39.2,L29.

JC63-01166A SHEET-MP-SENSOR;CLX-3160FN,PET,T0.125,W3

JC63-01253A SHEET-BOTTLE AUGER;CLP-300,PET,T0.125,-,

JC64-00218A SHUTTER-M-TONER BOTTLE;CLP-300,POM HB,-,

JC64-00260A HANDLE-M-BOTTLE;CLP-300,ABS,T5.9,W32.3,L

JC64-00260B HANDLE-BOTTLE Y;CLP-300,ABS,T5.4,-,L43.6

JC64-00260C HANDLE-BOTTLE M;CLP-300,ABS,T5.4,-,L43.6

JC64-00260D HANDLE-BOTTLE C;CLP-300,ABS,T5.4,-,L43.6

JC66-01095A GEAR-AGITATOR BOTTLE;CLP-300,POM(DE8903)

JC66-01139A GEAR-AUGER A;CLP-300,POM,M0.6,Z89,T4.1,B

JC66-01140A GEAR-AUGER B;CLP-300,POM,M0.6,Z56,T4.1,W

Z4489

O1054

SNA

SNA

Z4529 SNA

SNA

SA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SA

SNA

SA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

11

Parts List

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

#N/A

#N/A

#N/A

#N/A

SEC-Code

JC66-01141A

JC66-01144A

JC66-01145A

JC66-01146A

Description & Specification

GEAR-AUGER Z15;CLP-300,POM,M0.6,Z15,T3.5

SHAFT-AUGER;CLP-300,POM,L67,OD16,BLACK,-

SHAFT-SPRING;CLP-300,POM,L16.5,OD11.5,BL

SHAFT-AUGER K;CLP-300,POM,L70.3,OD10,WHI

Location Service

SNA

SNA

SNA

SNA

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

JC66-01216A PULLEY-M REGI;CLX-3160FN,POM,HB,WHITE,PI

JC66-01217A PULLEY-M FEED;CLX-3160FN,POM,HB,-,PI6,PI

JC66-01219A LEVER-M ACTUATOR MANUAL;CLX-3160FN,PC,T2

JC67-00131A TANK-M-TONER BOTTLE Y;CLP-300,ABS HB,-,P

JC67-00134A TANK-M-TONER BOTTLE BK;CLP-300,ABS HB,-,

JC67-00135A CAP-M-TONER BOTTLE;CLP-300,ABS HB,-,PI59

JC67-00135B CAP-TONER BOTTLE C;CLP-300,ABS HB,T10.87

JC67-00135C CAP-TONER BOTTLE M;CLP-300,ABS HB,T10.87

JC67-00136A

JC67-00137A

JC67-00140A

JC67-00141A

JC67-00142A

CAP-M-TONER BOTTLE BK;CLP-300,ABS HB,-,P

CAP-M-CRUM BOTTLE;CLP-300,ABS HB,-,PI52,

CAP-M-CRUM BOTTLE BK;CLP-300,ABS(HF-0660

CAP-M-CRUM BOTTLE C;CLP-300,ABS(HF-0660I

CAP-M-CRUM BOTTLE M;CLP-300,ABS(HF-0660I

JC67-00145A CAP-M-TONER;CLP-300,PP,T4.5,ID16.7,OD19,

JC67-00187A CAP-BOTTLE Y;CLP-300,PET,T0.65,W64.53,L5

JC67-00188A CAP-BOTTLE BK;CLP-300,PET,T0.65,R39.1,L5

JC68-00761B MANUAL-REGISTRATION CARD;COMMON,XAC,FREN

JC68-00761D MANUAL-REGISTRATION;COMMON,XAA,FRENCH,CA

JC68-01154A LABEL(R)-POP(A);COMMON,-,PC+HOLOGRAM,T0.

JC68-01344A MANUAL-WARRANTY CARD;CLP-500,XAA,ENGLISH

JC68-01344B MANUAL-WARRANTY CARD;COMMON,SAMSUNG,ENGL

JC68-01344C MANUAL-WARRANTY CARD;COMMON,SAMSUNG,FREN

JC68-01381B LABEL(R)-PPID(DEVE);COMMON,DELL,ART,0.05

JC68-01563A MANUAL-800 SEC CARD;COMMON,XAA,ENGLISH,E

JC68-01579A MANUAL-NETWORK GUIDE;CLP-600N,SEC,-,COMM

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

JC68-01584A LABEL(P)-BLANK 90*25;CLP-510,SEE,ART 100

JC68-01695A LABEL-POP;CLX-3160FN,-,HOLOGRAM PAPER,0.

JC68-01696A LABEL-POP;CLX-3160FN,-,PP,0.08T,300,80,O

JC68-01707A LABEL-FUNCTION;CLP-300,-,YUPO,T0.2,W10,L

JC68-01805A LABEL-FUNCTION;CLP-300,SEC,YUPO,T0.2,W10

JC68-10932A LABEL(P)-BLANK(ML);ML-85,ART,70X60,G100,

JC69-00453A BOX(P)-SAFETY PAD;COMMON,LDPE,A,3,45,300

JC69-00957E CUSHION-FRONT;CLX-3160FN,EPP,T10,W285,L1

JC69-00961A PAD-FRICTION;CLP-300,NBB,T1.0,W9.0,L39.5

JC69-01032A CUSHION-EPP_TOP;CLX-3160,EPP,-,546,584,2

JC69-01033A CUSHION-BOTTOM;CLX-3160,EPP,-,546,584,11

JC69-01034B CUSHION-BLOCK;CLX-3160,EPS,-,106,463,25,

JC69-01052A CUSHION-MAIN_FRONT;CLX-3160,EPP,-,530,60

JC72-00102A PMO-BUSHING_TR(L);SF-5100,POM (CH-15),BL

JC72-01384A SPONGE-CAP BOTTLE;CLP-300,POLYURETHANE F

JC72-01389A SPONGE-CRUM;CLP-300,PORON,-,T2,W8,L12,-,

JC92-01710A PBA SUB-CRUM_Y;CLP-300,SEC,KOREA,CRUM_Y,

JC92-01711A PBA SUB-CRUM_M;CLP-300,SEC,KOREA,CRUM_M,

JC92-01712A PBA SUB-CRUM_C;CLP-300,SEC,KOREA,CRUM_C,

JC92-01713A PBA SUB-CRUM_K;CLP-300,SEC,KOREA,CRUM_K,

JC92-01718A PBA SUB-EXIT;CLP-300,SEC,KOREA,EXIT SENS

JC94-01091A PHANTOM AU JC92-01746A

JC94-01251A PHANTOM AU JC92-01707D

JC96-04001A ELA UNIT-CONNECTOR;CLP-300,SEC,EXPORT,-,

JC97-01401A MEA UNIT-TERMINAL:TR;ML-5000A,SAMSUNG,KO

JC97-01771A MEA UNIT-TERMINAL S;CLP-500,SEC,EXPORT,S

JC97-02362A MEA UNIT-DRAW;CLP-300,SEC,WORLD,-,-,-,-

D2120

Z4480

O1101

Z4475

Z4500

K3635

Z4476

SNA

SA

SNA

SNA

SNA

SNA

SNA

SNA

SA

SNA

SNA

SA

SA

SA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SA

SNA

SNA

SNA

SA

SA

12

Parts List

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

#N/A

#N/A

#N/A

#N/A

SEC-Code

JC97-02638A

JC97-02640A

JC97-02641A

JC97-02642A

Description & Specification

MEA UNIT-TERMINAL GND;CLP-300,SEC,EXPORT

MEA UNIT-REGIACTUATOR;CLP-300,SEC,EXPORT

MEA UNIT-EXIT ROLLER;CLP-300,SEC,EXPORT,

MEA UNIT-EMPTY ACT;CLP-300,SEC,EXPORT,-,

Location Service

SA

SA

SA

SA

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

JC97-02829A MEA UNIT-PLATE K_UP;CLP-300,SEC,WORLD,-,

JG61-40001A FOOT-SF4000;SF4000,CR,-,BLK,CR,3,-,-

JG72-40960A PMO-CAP TONER;SF6000,PP,BLK,-,-,VO,-,-,-

0201-001162 ADHESIVE-CYA;LOCTITE403,NTR,1250,20G

0201-001183 ADHESIVE-AA;ARON ALPHA #202F,NTR,100,20G

0201-001235 ADHESIVE-TS;DEH-390D,RED,400,-

0201-001594 ADHESIVE-CYA;CA-40,CLEAR,2-10,1.05/8.7

0202-001459 SOLDER-CREAM;S3X58-M405,-,D20~38§-,96.5SS

0402-000132

0402-001212

0403-000287

0404-000112

0407-000122

DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP

DIODE-RECTIFIER;SS26,60V,2.0A,DO-214AA,T

DIODE-ZENER;MMBZ5251B,20.9-23.1V,225MW,S

DIODE-SCHOTTKY;RB420D,40V,100MA,SOT-23,T

DIODE-ARRAY;KDS226,80V,300mA,C2-3,SOT-23

0501-000342 TR-SMALL SIGNAL;KSC1623-Y,NPN,200mW,SOT-

0501-000462 TR-SMALL SIGNAL;MMBT2907A,PNP,350mW,SOT-

0501-000479 TR-SMALL SIGNAL;KST42,NPN,350mW,SOT-23,T

0501-000632 TR-SMALL SIGNAL;2SB1197K,PNP,200mW,SOT-2

0502-001258 TR-POWER;FJT44,NPN,-,SOT-223,TP,40-200

0505-001326 FET-SILICON;SI2308DS,N,60V,2A,0.22OHM,1.

0505-001350 FET-SILICON;NDT2955,P,-60V,-2.5V,0.3OHM,

0801-002446 IC-CMOS LOGIC;74LCX14,SCHMITT INVERTER,T

0803-000634 IC-TTL;74LS07,BUFFER/DRIVER,SOP,14,150MI

0904-001865 IC-USC;OTG242LP,16BIT,LQFP,64P,10.0X10.0

0904-001989 IC-USC;ISP1582BS,-,HVQFN56,56P,8X8X0.85M

1006-001316 IC-LINE DRIVER;FIN1047M,SOP,16P,10X6MM,-

F1017

SA

SA

SA

SA

SA

SA

SA

SNA

SA

SA

SA

SNA

SA

SA

SNA

SNA

SNA

SNA

SNA

SNA

SA

SA

DNA

SA

SA

1105-001379 IC-DRAM;K4S561632,-,256MBIT,4X4MX16BIT,T

1106-001228 IC-SRAM;6R1016,64KX16BIT,TSOP,44P,400MIL

1107-001286 IC-FLASH MEMORY;29LV160,2MX8/1MX16BIT,TS

1201-000105 IC-AUDIO AMP;34119,SOP,8P,150MIL,SINGLE,

1202-000164 IC-VOLTAGE COMP.;393,SOP,8P,150MIL,DUAL,

1203-001455 IC-POSI.FIXED REG.;1117,DPAK,3P,265MIL,P

1203-002233 IC-RESET;XC61F,SOT-23,3P,-,PLASTIC,0.7/1

1203-003739 IC-DC/DC CONVERTER;MVPG31,DFN,12P,4X3MM,

1204-002457 IC-SIGNAL PROCESSOR;HT82V26A,209MIL,28P,

1205-002339 IC-CLOCK GENERATOR;CY25811SC,SOIC,8P,150

1205-002478 IC-DAA;CX20493-21/FAX,QFN,28P,5X5MM,PLAS

1205-002593 IC-TRANSCEIVER;E-STE100P,TQFP,64P,10X10M

1205-002654 IC-MODEM;CX86710-12,TQFP,64P,7X7MM,PLAST

1401-001069 THYRISTOR-SIDAC;P3100EB,275V,0.15A,250A,

1404-001065 THERMISTOR-PTC;0.11OHM,-,-,13.2VAC,40A,1

1405-000170 VARISTOR;82V,1200A,9x4.1mm,TP

2007-000052 R-CHIP;10Kohm,1%,1/10W,TP,1608

2007-000066 R-CHIP;20Kohm,1%,1/10W,TP,1608

2007-000067 R-CHIP;15Kohm,1%,1/10W,TP,1608

2007-000077 R-CHIP;470ohm,5%,1/10W,TP,1608

2007-000080 R-CHIP;2Kohm,5%,1/10W,TP,1608

2007-000082 R-CHIP;3.3Kohm,5%,1/10W,TP,1608

2007-000083 R-CHIP;3Kohm,5%,1/10W,TP,1608

2007-000086 R-CHIP;5.6Kohm,5%,1/10W,TP,1608

2007-000092 R-CHIP;15Kohm,5%,1/10W,TP,1608

2007-000093 R-CHIP;20Kohm,5%,1/10W,TP,1608

2007-000097 R-CHIP;47Kohm,5%,1/10W,TP,1608

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SNA

SA

SA

SA

SNA

SNA

SNA

SA

SA

SNA

SA

SA

13

Parts List

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

#N/A

#N/A

#N/A

#N/A

SEC-Code

2007-000105

2007-000106

2007-000107

2007-000113

Description & Specification

R-CHIP;200Kohm,5%,1/10W,TP,1608

R-CHIP;220Kohm,5%,1/10W,TP,1608

R-CHIP;470Kohm,5%,1/10W,TP,1608

R-CHIP;33ohm,5%,1/10W,TP,1608

Location Service

SA

SA

SA

SA

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

2007-000123 R-CHIP;1.5Kohm,5%,1/10W,TP,1608

2007-000132 R-CHIP;180Kohm,5%,1/10W,TP,1608

2007-000133 R-CHIP;330Kohm,5%,1/10W,TP,1608

2007-000134 R-CHIP;33Kohm,5%,1/10W,TP,1608

2007-000136 R-CHIP;300Kohm,5%,1/10W,TP,1608

2007-000239 R-CHIP;1.5Kohm,1%,1/10W,TP,1608

2007-000287 R-CHIP;100OHM,1%,1/10W,TP,1608

2007-000309 R-CHIP;10ohm,5%,1/10W,TP,1608

2007-000475

2007-000481

2007-000539

2007-000660

2007-000740

R-CHIP;1Mohm,1%,1/10W,TP,1608

R-CHIP;1Mohm,5%,1/4W,TP,3216

R-CHIP;200ohm,5%,1/10W,TP,1608

R-CHIP;27ohm,5%,1/4W,TP,3216

R-CHIP;30Kohm,5%,1/4W,TP,3216

2007-000965 R-CHIP;5.1Kohm,5%,1/10W,TP,1608

2007-001044 R-CHIP;56ohm,5%,1/10W,TP,1608

2007-001056 R-CHIP;6.2Kohm,5%,1/10W,TP,1608

2007-001134 R-CHIP;68ohm,5%,1/10W,TP,1608

2007-001161 R-CHIP;75Kohm,5%,1/10W,TP,1608

2007-002760 R-CHIP;6.8Mohm,5%,1/4W,TP,3216

2007-002901 R-CHIP;12.1Kohm,1%,1/10W,TP,1608

2007-007226 R-CHIP;49.9ohm,1%,1/10W,TP,1608

2007-007239 R-CHIP;31.6Kohm,1%,1/10W,TP,1608

2007-007297 R-CHIP;110ohm,1%,1/10W,TP,1608

2007-007998 R-CHIP;348KOHM,1%,1/4W,TP,3216

2007-008371 R-CHIP;280Kohm,1%,1/10W,TP,1608

SA

SNA

SA

SA

SNA

SA

SA

SNA

SNA

SNA

SNA

SNA

SA

SNA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

2007-008473 R-CHIP;59Kohm,1%,1/10W,TP,1608

2007-008510 R-CHIP;237KOHM,1%,1/4W,DA,TP,3216

2011-001094 R-NET;39OHM,5%,1/16W,L,CHIP,8P,TP

2011-001261 R-NET;33ohm,5%,1/16W,L,CHIP,8P,TP,2.0x1.

2203-000041 C-CER,CHIP;0.01nF,0.25pF,50V,C0G,1608

2203-000357 C-CER,CHIP;0.15nF,5%,50V,C0G,1608

2203-000384 C-CER,CHIP;0.015nF,5%,50V,C0G,1608

2203-000426 C-CER,CHIP;0.018nF,5%,50V,C0G,1608

2203-000491 C-CER,CHIP;2.2nF,10%,50V,X7R,1608

2203-000681 C-CER,CHIP;0.027nF,5%,50V,C0G,1608

2203-000783 C-CER,CHIP;0.33nF,5%,50V,C0G,1608

2203-000815 C-CER,CHIP;0.033nF,5%,50V,C0G,1608

2203-000975 C-CER,CHIP;47nF,10%,25V,X7R,TP,1608,-

2203-001071 C-CER,CHIP;0.056nF,5%,50V,C0G,1608

2203-001598 C-CER,CHIP;2200nF,+80-20%,16V,Y5V,2012

2203-001607 C-CER,CHIP;0.22nF,5%,50V,NP0,1608

2203-005221 C-CER,CHIP;15nF,10%,50V,X7R,1608

2203-005384 C-CER,CHIP;4700nF,+80-20%,10V,Y5V,2012

2203-005757 C-CER,CHIP;33nF,10%,200V,X7R,TP,3216

2203-005758 C-CER,CHIP;47nF,10%,200V,X7R,TP,3216

2203-005819 C-CER,CHIP;1000nF,+80-20%,16V,Y5V,-,1608

2203-006001 C-CER,CHIP;0.1NF,5%,3KV,NPO,TP,4520

2203-006468 C-CER,CHIP;10nF,+-10%,250V,X7R,-,2012

2203-006474 C-CER,CHIP;22000nF,20%,6.3V,X5R,2012

2203-006646 C-CER,CHIP;10000nF,10%,6.3V,X5R,2012

2401-000207 C-AL;100uF,20%,50V,WT,TP,8x12,5

2402-001049 C-AL,SMD;10uF,20%,16V,GP,TP,3.3x3.3x5.4

SA

SA

SA

SA

SA

SA

SA

SNA

SNA

SNA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SA

SNA

SA

14

Parts List

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

#N/A

#N/A

#N/A

#N/A

SEC-Code

2602-000061

2602-000062

2703-000300

2703-002055

Description & Specification

TRANS-PULSE;30UH,0.225/0.325OHM,1:1.5,9.

TRANS-PULSE;450UH,0.25/0.25OHM,1:1,12.8X

INDUCTOR-SMD;1uH,10%,1608

INDUCTOR-SMD;2.2UH,20%,6363

Location Service

SA

SA

SA

SNA

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

2801-000111 CRYSTAL-SMD;0.032768MHZ,20PPM,28-AAW,12.

2804-001520 OSCILLATOR-CLOCK;6MHz,25ppm,10TTL,15pF,T

2901-001178 FILTER-EMI SMD;25V,2A,-,100000pF,2x1.25x

3301-000325 BEAD-SMD;60ohm,3.2x2.5x1.3mm,400mA,TP,,,

3301-001084 BEAD-SMD;600ohm,2012,300mA,TP,522ohm/70M

3301-001122 BEAD-SMD;600ohm,1.6x0.8x0.8mm,TP,-,-

3301-001240 BEAD-SMD;120ohm,1608,200mA,,393ohm/305MH

3711-003411 HEADER-BOARD TO CABLE;BOX,5P,1R,2mm,STRA

3722-001051

4715-001084

6009-001396

6021-000222

6044-001035

JACK-USB;4P/1C,AU,BLK,ANGLE,A TYPE

SURGE ABSORBER;600V,20%,500A,-,RADIAL(TP

SCREW-SPECIAL;PH,+,-,M3,L10.3,ZPC(BLK),S

NUT-HEXAGON;2C,M3,ZPC(YEL),SM20C,-

RING-ETC;ID2.2,OD6.4,T3,BLK,STS304

6107-001299 SPRING-ES;SUS304-WPB,PI0.35,D2,L22.8,ID1

6601-001384 BEARING-BALL;676ZZ,ID6,OD10,L3,GCr 15 +

JC13-00031C IC ASIC-CHORUSM;CHORUSM,SCX-5530FN,496PI

JC39-00036A CBF HARNESS-OPE GND;SF-5100,#18,UL 1007,

JC39-00490A WIRE HARNESS-WASTE_T;CLP-300,WIRE HARNES

JC39-00492A CBF HARNESS-PTL;CLP-300,WIRE HARNESS,UL1

JC39-00493A CBF HARNESS-THER;CLP-300,WIRE HARNESS,UL

JC39-00495A CBF HARNESS-EXIT;CLP-300,WIRE HARNESS,UL

JC39-00577A CBF HARNESS-DEVE_ITB;CLP-300,WIRE HARNES

JC39-00580A CBF HARNESS-DEVE_HOME;CLP-300,WIRE HARNE

JC39-00607A HARNESS-REGI_EMT_MP;CLX-3160,HARNESS,UL1

JC41-00300B PCB-MAIN;CLP-300,FR-4,6L,1.3,1.6T,-,-,-,

SA

SNA

SA

SNA

SNA

SNA

SNA

SNA

SA

SNA

Z4565 SNA

Z4564 SNA

SNA

SA

Z4519 SNA

Z6023

Z6026

SA

SA

Z4457

SA

SNA

SA

SA

SNA

SA

SA

SNA

JC41-00318A PCB-MODEM;SCX-5530FN, FR4,2,-,1.6T,114*5

JC60-00014A FLANGE-M-DRUM OPC;CLP-300,PC(LF1025),W11

JC60-00015A SPACER-M-DR G;CLP-300,KL4540,-,ID6.03,OD

JC61-00424A BUSH-4;ML-9400W,NTN B-F4-42,-,-,-,NTR,-

JC61-01120B PLATE-CRUM;CLP-300,C5210P,0.15,W3,L5.2,-

JC61-01281A BRACKET-P-BAR_PICK_UP;ML-1610,SECC,T1.0,

JC61-01466A FRAME-M-T2 BASE;CLP-300,PC+ABS,-,HB,BLAC

JC61-01467A PLATE-P-T2 GROUND;CLP-300,C5210P 1/2H TA

JC61-01468A GUIDE-P-T2 OUTPUT;CLP-300,SECC,T0.6,-,22

JC61-01469A HOLDER-M-LOCATE SHAFT;CLP-300,POM (M90-4

JC61-01470A GUIDE-P-T2 INPUT;CLP-300,SECC,T0.6,-,230

JC61-01492A FRAME-M-LEFT OPC;CLP-300,ABS+GF20%,-,-,B

JC61-01493A FRAME-M-RIGHT OPC;CLP-300,ABS+GF20%,-,-,

JC61-01496A HOUSING-M-CLEANING OPC;CLP-300,ABS GF 20

JC61-01500A BRACKET-P-CLEANING ITB;CLP-300,SECC,1.6T

JC61-01501A PLATE-P-EARTH OPC;CLP-300,C5210P,T0.2,ID

JC61-01508A FRAME-M-DEVE YELLOW;CLP-300,ABS+GF20%,GR

JC61-01509A FRAME-M-DEVE MAGENTA;CLP-300,ABS+GF20%,G

JC61-01510A FRAME-M-DEVE CYAN;CLP-300,ABS+GF20%,GR40

JC61-01511A FRAME-M-DEVE BLACK;CLP-300,ABS+GF20%,GR4

JC61-01512A HOLDER-M-DEVE YELLOW L;CLP-300,ABS+GF20%

JC61-01516A GUIDE-M-DEVE;CLP-300,ABS+GF20%,GR4020,22

JC61-01518A PLATE-P-SUPPLY ROLLER;CLP-300,SUS 301-CS

JC61-01519A PLATE-P-DEVE ROLLER;CLP-300,SUS 301-CSP

JC61-01526A GUIDE-M-BUSH IDL ITB R;CLP-300,POM M90-4

JC61-01527A HOLDER-P-SEAL DEVE L;CLP-300,SUS301-CSP

JC61-01528A HOLDER-P-SEAL DEVE R;CLP-300,SUS301-CSP

K2867

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

15

Parts List

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

#N/A

#N/A

#N/A

#N/A

SEC-Code

JC61-01529A

JC61-01561A

JC61-01562A

JC61-01572A

Description & Specification

HOLDER-M-CRUM;CLP-300,ABS(XR-409),T2.0,W

HOLDER-M-DEVE ROLLER;CLP-300,POM M90-44,

GUIDE-M-DRIVE ITB;CLP-300,POM(M90-44),-,

HOLDER-M-SHAFT CLUTCH;CLP-300,POM,T1.5,D

Location Service

SNA

SNA

SNA

SA

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

JC61-01576A BUSH-SHAFT;CLP-300,POM,ID3.0,OD4.5,T3.5,

JC61-01669A GUIDE-M-SENSOR L;CLP-300,PS,T10.29,W11.7

JC61-01670A GUIDE-M-SENSOR R;CLP-300,PS,T10.29,W11.7

JC61-01671A GUIDE-M-SENSOR BK R;CLP-300,PS,T10,W13.4

JC61-01672A GUIDE-M-SENSOR BK L;CLP-300,PS,T10,W13.4

JC61-01673A BLADE-CLEANING ITB;CLP-300,POLYURETHANE,

JC61-01684A BLADE-SENSOR;CLP-300,PET FILM,-,W6.3*L9.

JC61-01700A GUIDE-WASTE;CLP-300,PC,-,31,41,TRANSPARE

JC61-01750A

JC61-01751A

JC61-01753A

JC61-01775A

JC61-70929A

BRACKET-P_GUIDE PR;CLP-300,SUS,T1.0,W232

GUIDE-P_PAPER PR;CLP-300,SUS304,T0.1,W21

PLATE-_P-DEVE SUPPORT;CLP-300,STSC301-CS

BRACKET-CAM BAR;CLP-300,SECC,T1.2,W4.5,L

SPRING ETC-HV LARGE;ML-5000A,SUS304-WPB,

JC62-00211A SEAL-DRUM OPC;CLP-300,URETHANE FILM,-,T0

JC62-00215A SEAL-SIDE DEVE;CLP-300,PORON LE20,BLACK,

JC62-00216A SEAL-BRACKET OPC;CLP-300,EPDM,-,T2.7,W3,

JC62-00226A SEAL-DOCTOR BLADE;CLP-300,EPDM,-,T4.0,W4

JC62-00230A SEAL-SIDE RIGHT OPC;CLP-300,POLYURETHANE

JC62-00231A SEAL-SIDE LEFT OPC;CLP-300,POLYURETHANE

JC62-00234A SEAL-DEVE BLOCK;CLP-300,POLYURETHANE,-,3

JC62-00235A SEAL-DEVE ROLLER;CLP-300,PET Film,-,0.07

JC62-00236A SEAL-DEVE FRONT;CLP-300,PET FILM,-,0.075

JC62-00240A SEAL-AUGER;CLP-300,PORON ,BLACK,T5.0,ID4

JC62-00241A SEAL-COVER DUCT;CLP-300,PE FOAM,-,T2.0,W

JC62-00256A SEAL-FRAME WASTE OPC;CLP-300,PORON LE-20

Z4437

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SA

JC62-00260A SEAL-CAP CRUM;CLP-300,Polyurethane Foam(

JC62-00262A SEAL-WASTE;CLP-300,PE FORM,-,T3.0,W4,L13

JC62-00269A SEAL-COVER FRONT;CLP-300,PE FOAM,-,T2.0,

JC62-00270A SEAL-COVER BOTTOM;CLP-300,POLYURETHANE F

JC62-00271A SEAL-COVER DEV K;CLP-300,PE FOAM,-,T3.0,

JC62-00272A SEAL-LSU REAR;CLP-300,URETHAN FILM,NTR,T

JC62-00273A SEAL-DEVE ROLLER K;CLP-300,PET FILM,-,T0

JC62-00274A SEAL-SIDE GAP OPC;CLP-300,POLYURETHAN FO

JC62-00275A SEAL-BLADE;CLP-300,PE FOAM,-,T3.0,W3,L8.

JC62-00279A SEAL-SENSOR BK;CLP-300,FLOCKING(DOBIRU),

JC62-00280A SEAL-SENSOR Y;CLP-300,FLOCKING(DOBIRU),B

JC62-00306A SEAL-CAP DUCT;CLP-300,FLOCKING,-,T0.5,W8

JC62-00307A SEAL-SENSOR;CLP-300,FLOCKING,-,T0.5,W13.

JC62-00308A SEAL-DOCTOR BLADE S;CLP-300,EPDM,-,T2.0,

JC62-00320A SEAL-WASTE F;CLP-300,PE FOAM,GRAY,2.0T,W

JC62-00321A SEAL-WASTE R;CLP-300,PE FOAM,GRAY,2.0T,w

JC62-00324A SEAL-WASTE B;CLP-300,POLY-URETHANE(SHL),

JC62-00341A SEAL-WASTE EXIT;CLP-300,PORON LE-20 + PE

JC62-00342A SEAL-SIDE CLN OPC;CLP-300,POLYURETHANE F

JC62-00343A SEAL-SENSOR TOP;CLP-300,EPDM,-,T2.5,W4,L

JC63-00858A COVER-M-WASTE OPC;CLP-300,ABS,T2,W15.8,L

JC63-00883A COVER-M-WASTE;CLP-300,PC(141R),T2.0,W77,

JC63-00898A COVER-M-DEVE Y;CLP-300,ABS HF0660I,T1.5,

JC63-00899A COVER-M-DEVE M;CLP-300,ABS HF0660I,T1.5,

JC63-00900A COVER-M-DEVE C;CLP-300,ABS HF0660I,T1.5,

JC63-00901A COVER-M-DEVE K;CLP-300,ABS HF0660I,T1.5,

JC63-01037A TRAY-M-MP;CLX-3160FN,ABS,T2.0,W245.4,L17

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SA

16

Parts List

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

#N/A

#N/A

#N/A

#N/A

SEC-Code

JC63-01048A

JC63-01086A

JC63-01087A

JC63-01142A

Description & Specification

SHEET-COVER HARNESS;CLP-300,PC,T0.125,W4

SHEET-WASTE;CLP-300,PET,T0.188,W24,L24,B

SHEET-LSU COVER;CLP-300,PC,T0.38,W17,L23

SHEET-FILM YELLOW UP;CLP-300,PC,T0.38,W5

Location Service

Z4615

SNA

SNA

SNA

SNA

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

JC63-01164A SHEET-HOUSING REAR;CLP-300,PC,T0.38,W11.

JC64-00276A LOCKER-FRAME;CLP-300,PC,BLK,-,-,-

JC66-00494A GEAR-OPC ROLL CLEAN_Z18;CLP-500,POM,M0.8

JC66-00604A ROLLER-CHARGER CLEANING;CLP-500,URETHAN+

JC66-00720A SHAFT-P-CORE;ML-1750,SECC 1.2T,203,-,-,-

JC66-00830A ROLLER-M-EXIT FR;ML-1610,TEFLON,6.5,L22.

JC66-00896A ROLLER-M-IDLE_ DUP;ML-3560,POM,OD9.6,14.

JC66-01058A LATCH-M-CLUTCH SPRING;CLP-300,POM,T1.2,D

JC66-01069A

JC66-01072A

JC66-01074A

JC66-01075A

JC66-01081A

GEAR-CLUTCH DEVE CAM;CLP-300,POM,M0.6,Z2

SHAFT-LOCATE;CLP-300,SUM 22+NI(COATING),

LEVER-M-RELEASE R;CLP-300,ABS+GF20%,T2.0

LEVER-M-RELEASE L;CLP-300,ABS+GF20%,T2.0

GEAR-RDCN T2 DRIVE;CLP-300,POM,M0.8/M0.8

JC66-01084A SHAFT-M-AUGER OPC;CLP-300,ABS+GF20%,L250

JC66-01086A GEAR-DRUM OPC;CLP-300,PC(LF1025),M0.6,Z9

JC66-01088A SHAFT-OPC;CLP-300,SUS303,L284.5,OD6,-,-,

JC66-01090A GEAR-DEVE ROLLER;CLP-300,POM DE8903,M0.6

JC66-01091A GEAR-SUPPLY ROLLER;CLP-300,POM DE588P,M0

JC66-01092A SHAFT-M-AUGER SUPPLY;CLP-300,ABS GF20% G

JC66-01093A SHAFT-M-BELT;CLP-300,POM(M90-44),24.8,¥ÕS

JC66-01100A SHAFT-M-AUGER TONER M;CLP-300,ABS GF20%

JC66-01101A SHAFT-M-AUGER TONER C;CLP-300,ABS GF20%

JC66-01102A SHAFT-M-AUGER TONER K;CLP-300,ABS GF20%

JC66-01107A GEAR-AUGER SUPPLY;CLP-300,POM DE588P,M0.

JC66-01109A GEAR-AUGER TONER;CLP-300,POM DE588P,M0.5

O1068

D2117

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SA

SNA

SA

SNA

SA

SNA

SNA

SNA

SA

JC66-01121A LEVER-M-T2 HOLDER R;CLP-300,ABS+GF20%,T2

JC66-01122A LEVER-M-T2 HOLDER L;CLP-300,ABS+GF20%,T2

JC66-01123A GEAR-AUGER OPC;CLP-300,POM (M90-44),M0.5

JC66-01124A GEAR-IDLE OPC;CLP-300,POM (M90-44),M0.6/

JC66-01125A ROLLER-DEVE;CLP-300,NBR+ECO,OD10,L295.3,

JC66-01126A ROLLER-SUPPLY;CLP-300,Fur Brush,OD9.15,L

JC66-01127A DRUM-OPC;CLP-300,AL,ID58,OD60,L248,-,-

JC66-01129A ROLLER-DRIVE ITB;CLP-300,AL+EPDM,OD29.7,

JC66-01130A ROLLER-IDLE ITB;CLP-300,AL,OD30,L234,-,-

JC66-01137A GEAR-DRIVE ITB;CLP-300,PC(LF1025),M0.5,Z

JC66-01142A ROLLER-SLIDE A;CLP-300,POM,L10,OD10.2,BL

JC66-01230A SHAFT-DEVE FRAME;CLP-300,SUS303,L28.4,¡ËS

JC66-01295A SHAFT-AUGER SUPPLY Y;CLP-300,ABS GF20% G

JC66-01298A SHAFT-AUGER SUPPLY C;CLP-300,ABS GF20% G

JC66-01299A SHAFT-AUGER SUPPLY M;CLP-300,ABS GF20% G

JC67-00143A CAP-M-WASTE BOTTLE;CLP-300,LDPE(MB9205),

JC67-00144A TANK-M-WASTE;CLP-300,ABS(TR557A),T2.0,W1

JC67-00162A CAP-DUCT;CLP-300,NBR,T0.7,17.8,19.7,-,-

JC69-01055A PAD-KNOCK UP;CLP-300,RUB-OTH,T1.0,W10,L3

JC70-00050A IPR-TERMINAL;SF-5100,SWRCH1018,-,-,-,-,8

JC70-00521A ADJUST-M-MP_L;CLX-3160FN,ABS HB,T2.0,W11

JC70-00522A ADJUST-M-MP_R;CLX-3160FN,ABS HB,T2.0,W11

JC70-10232A IPR-PLATE SAW;ML-80,SUS304 CSP 1/2H,-,T0

JC70-10961A IPR-TERMINAL FU;ML-165,C5210P,-,T0.3,-,-

JC70-40912A ICT-SHAFT HV LARGE;ML-5000A,SWCH18A,-,¥÷

JC70-50901A IPR-IPM BUSHING DEV R;ML-5000,BRONZE,-,D

JC71-00009A NPM-BUSHING DEV R;ML-6060,BRONZE,D7*12,-

SNA

SNA

SNA

SNA

SNA

SNA

SNA

Z4562 SNA

O1099

K3422

O1100

SA

SA

SA

SA

SA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

17

Parts List

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

#N/A

#N/A

#N/A

#N/A

SEC-Code

JC72-00463A

JC72-00465A

JC72-01004A

JC72-41010A

Description & Specification

PMO-CAP CONNECTOR L;ML-6060A,POM,BLACK,-

PMO-CAP CONNECTOR U;ML-6060A,POM,BLACK,-

PMO-IDLE KNOCK UP MP;ML-2150,POM,BLK,-,M

PMO-HOUSING TERMINAL;ML-165,ABS GF10%,BL

Location Service

Z0013

Z0014

P0041

H6086

SA

SA

SA

SA

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

JC72-41105A PMO-BUSHING DEV;ML-5000,POM,NTR,-,-,-,-,

JC73-00217A RUBBER-BELT YELLOW;CLP-300,NBR,0.7T,-,22

JC73-00220A RUBBER-BELT BLACK;CLP-300,NBR,0.7T,-,22,

JC73-00221A RUBBER-BELT WASTE OPC;CLP-300,NBR,L335.9

JC92-01721A PBA SUB-REGI_EMPTY;CLP-300,SEC,KOREA,REG

JC92-01722A PBA SUB-WASTE_R;CLP-300,SEC,KOREA,WASTE_

JC94-00764A PHANTOM AU JC92-01636A

JC94-01119A

JC94-01120A

JC94-01121A

JC94-01122A

JC94-01123A

JC94-01125A

JC94-01126A

JC94-01129A

JC94-01130A

JC97-02416C MEA UNIT-COVER PLATEN;SCX-5530FN,SEC,-,-

JC97-02620A MEA UNIT-SUS BLADE;CLP-300,SEC,WORLD,-,-

JC97-02628A MEA UNIT-T2 ROLLER;CLP-300,SEC,WORLD,-,-

JC97-02643A MEA UNIT-BLADE OPC;CLP-300,SEC,EXPORT,-,

JC97-02644A MEA UNIT-CHARGE OPC;CLP-300,SEC,EXPORT,-

JC97-02694A MEA-GUIDE IDL ITB;CLP-300,SEC,WORLD,-,-,

JF27-60051A COIL FILTER;CF5400,60uH,50mOHM,18T

0401-000005 DIODE-SWITCHING;1N4148,75V,150mA,DO-35,T

0407-000101 DIODE-ARRAY;DA204K,20V,100mA,C2-3,SOT-23

0

0

0

0

0

0.1

0.1

0.1

0.2

Z6165

SNA

SNA

SNA

SA

SNA

SA

SNA

SNA

SNA

SA

SA

SA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

0601-001138 LED-IR;ROUND,5mm,150mW,4V,950nm,BK

0601-001908 LED;ROUND,RED,3MM,630NM,3.2X4.6MM

0603-001021 PHOTO TR;NPN,20V,5V,20mA,75mW,TP

1103-001366 IC-EEPROM;34C02,2KBIT,256X8BIT,SOP,8P,5X

2001-000831 R-CARBON;510OHM,5%,1/4W,AA,TP,2.4X6.4MM

2005-000419 R-WIRE WOUND,NON;0.33ohm,1%,1W,AA,TP,4.3

2201-000021 C-CERAMIC,DISC;100NF,+80-20%,50V,Y5V,TP,

2401-001363 C-AL;470uF,20%,16V,GP,TP,10x12.5,5

3301-000344 BEAD-RADIAL;200ohm,3.5x0.6x6.5mm,7000mA,

3711-002808 HEADER-BOARD TO CABLE;BOX,7P,1R,2mm,STRA

3711-003408 HEADER-BOARD TO CABLE;BOX,2P,1R,2mm,STRA

JC07-00003A LCD-DISPLAY(XEV);VHX1620BHRC9,SCX-5312F/

JC39-00306A CBF HARNESS-LCD;CLP-500,WIRE,UL2877,14-1

JC39-00491A CBF HARNESS-WASTE_R;CLP-300,WIRE HARNESS

JC39-00531A CBF HARNESS-CCD_HOME;SCX-5530FN,CBF,UL10

JC41-00171C PCB-PTL (1LAYER);SCX-4100,FR-1,1,-,1.6T,

JC41-00201A PCB-TONER_TX;CLP-500,FR-1,1L,-,1.2,15*10

JC41-00248A PCB-SUB (1LAYER);SCX-4720F,FR-1,1,-,1.6T

JC41-00296A PCB SUB-ITB_JOINT;CLP-300,FR-1,1L,-,1.6T

JC41-00298A PCB SUB-TONER_CRUM;CLP-300,FR-4,2L,-,1.6

JC61-01471A HOLDER-M-T2 ROLLER R;CLP-300,POM (M90-44

JC61-01507A PLATE-P-DOCTOR BLADE;CLP-300,SECC,1.2T,3

JC61-01525A GUIDE-M-BUSH IDL ITB L;CLP-300,POM M90-4

JC61-01545A BRACKET-P-CLEANING OPC;CLP-300,SECC,T1.2

JC61-01575A BLADE-P-DOCTOR;CLP-300,SUS,NATURAL,223*1

JC61-01668A COLLAR-M-CLUTCH;CLP-300,POM,ID11.4,OD13.

JC61-01674A BLADE-CLEANING OPC;CLP-300,POLY URETHANE

D2159

SA

SNA

SA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SA

SNA

SA

SNA

DNA

SA

SNA

SNA

SNA

SA

SNA

SNA

18

Parts List

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

#N/A

#N/A

#N/A

#N/A

SEC-Code

JC66-01073A

JC66-01098A

JC66-01104A

JC66-01224A

Description & Specification

GEAR-T2 ROLLER;CLP-300,POM,M0.8,Z28,-,WH

GEAR-CHARGE;CLP-300,POM (M90-44),M0.8,Z1

ROLLER-TRANSFER;CLP-300,SUM22+HYBRID FOA

GEAR-WORM CLUTCH;CLP-300,POM,M0.8,Z2,-,W

Location Service

SA

SNA

SNA

SNA

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

JC66-01308A ROLLER-CHARGE;CLP-300,NBR+ECO,D12,L230,-

JC68-01099A LABEL(P)-WARNING ADF;COMMON,SAMSUNG,ART1

JC70-00525A HUB-M-CLUTCH SPRING;CLP-300,POM,-,D13.4,

JC71-10322B NPR-EARTH OPC;-,ML-80,C5210P-1/2H,T0.2,-

JC94-01118A

JC94-01127A

JC94-01128A

JC94-01136A REV 0.1

0401-000116

0402-001189

0501-000279

0501-000457

0601-001226

DIODE-SWITCHING;MMSD914T1,100V,200MA,SOD

DIODE-RECTIFIER;M4,400V,1A,TS-1,TP

TR-SMALL SIGNAL;KSA1182-Y,PNP,150mW,SOT-

TR-SMALL SIGNAL;MMBT2222A,NPN,350mW,SOT-

LED;SMD,RED,1.2x0.8mm,660nm,1.6x0.8mm

0601-001830 LED;SMD,GRN,1.6x0.8x0.4mm,570nm,1.6x0.8x

0801-002469 IC-CMOS LOGIC;74HC14,SCHMITT INVERTER,TS

1001-000170 IC-ANALOG SWITCH;MC14051BD,SPDT CMOS,SOP

1003-001102 IC-MOTOR DRIVER;TEA3718DP,DIP,16P,300MIL

1404-001141 THERMISTOR-NTC;5.6Kohm,5%,3200K,2.1mW/C,

2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM

2007-000033 R-CHIP;0ohm,5%,1/4W,TP,3216

2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608

2007-000075 R-CHIP;220ohm,5%,1/10W,TP,1608

2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608

2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608

2007-000119 R-CHIP;560ohm,5%,1/10W,TP,1608

0

0.1

0.1

SA

SA

SA

SA

SNA

SA

SA

SA

SA

SA

SA

SA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SNA

SA

SA

SA

SA

2007-000120 R-CHIP;680ohm,5%,1/10W,TP,1608

2007-000122 R-CHIP;1.2Kohm,5%,1/10W,TP,1608

2007-000402 R-CHIP;150ohm,5%,1/10W,TP,1608

2007-000839 R-CHIP;39ohm,5%,1/10W,TP,1608

2007-000939 R-CHIP;47Kohm,1%,1/10W,TP,1608

2007-007233 R-CHIP;61.9ohm,1%,1/10W,TP,1608

2007-007550 R-CHIP;3.16Kohm,1%,1/10W,TP,1608

2007-007613 R-CHIP;121ohm,1%,1/10W,TP,1608

2011-001011 R-NET;10Kohm,5%,1/16W,L,CHIP,8P,TP,3.2x1

2203-000236 C-CER,CHIP;0.1nF,5%,50V,C0G,1608

2203-000998 C-CER,CHIP;0.047nF,5%,50V,C0G,1608

2203-001222 C-CER,CHIP;0.82nF,10%,50V,X7R,1608

2402-000008 C-AL,SMD;47uF,20%,16V,GP,TP,6.6x6.6x5.4

2802-001069 RESONATOR-CERAMIC;7.37MHz,0.5%,TP,4.7x4.

3711-000225 HEADER-BOARD TO CABLE;1WALL,4P,1R,2.5MM,

3711-002001 HEADER-BOARD TO CABLE;BOX,20P,2R,2MM,STR

3711-003204 HEADER-BOARD TO CABLE;BOX,24P,2R,2mm,STR

3711-003340 HEADER-BOARD TO CABLE;BOX,16P,2R,2mm,STR

3711-003409 HEADER-BOARD TO CABLE;BOX,3P,1R,2mm,STRA

3711-003410 HEADER-BOARD TO CABLE;BOX,4P,1R,2mm,STRA

3711-005561 CONNECTOR-HEADER;BOX,5P,1R,2MM,SMD-S,SN,

3711-005596 HEADER-BOARD TO CABLE;BOX,3P,1R,2MM,SMD-

3711-005851 HEADER-BATTERY;NOWALL,2P,1R,4.25MM,BATTE

3711-006032 CONNECTOR-HEADER;BOX,2P,1R,2MM,SMD-A,SN,

JB13-00004A IC ASIC-OPE;SF-3100,HT48C5,SSOP,48P,16.1

JB70-00236A ICT-HINGE SHAFT(4IN1);SCX-1150F,SWCH,5.0

JC41-00133A PCB-SENSOR;SCX-5100,FR-1,1L,-,1.6T,22X12

SA

SNA

SNA

SA

SA

SA

SNA

SNA

SA

SNA

SA

SNA

SA

SA

SA

SA

SA

SNA

SNA

SNA

SNA

SNA

SA

SA

SA

SA

SNA

19

Parts List

SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE

Drawer#

#N/A

#N/A

#N/A

#N/A

SEC-Code

JC41-00202A

JC41-00295A

JC41-00315A

JC41-00326A

Description & Specification

PCB-TONER_RX;CLP-500,FR-1,1L,-,1.2,15*10

PCB SUB-DEVE_JOINT;CLP-300,FR-1,1L,-,1.6

PCB-OPE;SCX-5530FN,FR-1,1,-,1.6T,380*93.

PCB SUB-JOINT;CLX-3160,FR-4,2L,1.6T,110*

Location Service

SNA

SNA

SNA

SNA

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

#N/A

JC61-00695A

JC61-00696A

JC61-00697A

JC62-00002A

HINGE-M-CAM;SCX-4216F,POM,-,-,-,WHITE,-,

HINGE-M-FRAME;SCX-4216F,POM,-,-,-,WHITE,

HINGE-M-PRESSURE;SCX-4216F,PC(LF1025),-,

HEAT SINK-(4500);ML-4500,BRONZE,0.5,9.3,

JC94-01252A PHANTOM AU JC92-01798A

JC94-01296A PHANTOM AU JC92-01859A

1003-001535 IC-MOTOR DRIVER;A3977SLP,TSSOP,28P,9.6X4

2001-000111 R-CARBON;150OHM,5%,1/4W,AA,TP,2.4X6.4MM

2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM

2001-000490 R-CARBON;200OHM,5%,1/8W,AA,TP,1.8X3.2MM

2001-000626 R-CARBON;300OHM,5%,1/4W,AA,TP,2.4X6.4MM

2001-000864 R-CARBON;56KOHM,5%,1/8W,AA,TP,1.8X3.2MM

2001-001031 R-CARBON;91KOHM,5%,1/8W,AA,TP,1.8X3.2MM

2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608

2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608

2007-000094 R-CHIP;22Kohm,5%,1/10W,TP,1608

2007-000096 R-CHIP;30Kohm,5%,1/10W,TP,1608

2007-000729 R-CHIP;300ohm,5%,1/10W,TP,1608

2201-000119 C-CERAMIC,DISC;100NF,+80-20%,50V,Y5V,TP,

2201-001057 C-CERAMIC,DISC;0.82NF,10%,50V,Y5P,TP,5X3

2202-000630 C-CERAMIC,MLC-AXIAL;100nF,10%,50V,X7R,TP

2203-000189 C-CER,CHIP;100nF,+80-20%,25V,Y5V,1608

2203-000192 C-CER,CHIP;100nF,+80-20%,50V,Y5V,2012

2203-000206 C-CER,CHIP;100nF,10%,50V,X7R,2012

2203-000257 C-CER,CHIP;10nF,10%,50V,X7R,1608

2203-000440 C-CER,CHIP;1nF,10%,50V,X7R,1608

2203-000626 C-CER,CHIP;0.022nF,5%,50V,C0G,1608

2203-002392 C-CER,CHIP;220nF,+80-20%,50V,Y5V,2012

2203-005249 C-CER,CHIP;100nF,10%,50V,X7R,1608

2401-000042 C-AL;100uF,20%,16V,GP,TP,6.3x7,5

2401-002300 C-AL;47¥ìF,20%,50V,GP,TP,6.3x11,5mm

JC39-40511A CBF HARNESS;ML-80,JUMPER,AWG22,52mm,SILV

JC41-00193B PCB-ADF ROCKY2;SCX-4720F,FR-1,1L,V1.0,1.

H3011

H3012

H3016

Z6058

D2176

SA

SA

SA

SA

SA

SA

SNA

SA

SA

SA

SA

SA

SA

SA

SA

SNA

SA

SA

SA

SNA

SA

SA

SA

SA

SNA

SNA

SA

SA

SA

SA

SA

SA

SA

20

9

9. Block Diagram

Block Diagram

Samsung Electronics

Service Manual

9-1

10. Connection Diagram

10

Connection Diagram

Samsung Electronics

Service Manual

10-1

11

1

. Reference Information

1 1 .1 Tool for Troubleshooting

Reference Information

1

1

This chapter contains the tools list, list of abbreviations used in this manual, and a guide to the location space required when installing the printer. A definition of test pages and Wireless

Network information definition is also included.

The following tools are recommended safe and easy troubleshooting as described in this service manual.

• Driver

Standard : "-" type, "+" type (M3 long, M3 short, M2 long, M2 short).

• Cleaning Equipments

Standard : An IPA (Isopropyl Alcohol) dry wipe tissue or a gentle neutral detergent and lint-free cloth.

• Tweezers

Standard : For general home use, small type.

• Vacuum Cleaner

• Cotton Swab

Standard : For general home use, for medical service.

• Spring Hook

Standard : For general use

• Software (Driver) installation CD ROM

Service Manual

11-1

Samsung Electronics

Reference Information

1

1

.2 Acronyms and Abbreviations

The table below explains abbreviations used in this service manual.

The contents of this service manual are declared with abbreviations in many parts. Please refer to the table.

11 .2.1 General

dbA dBM

DC

DCU

DPI

DRAM

DVM

DPI

DRAM

ECP

AC

ADF

ASIC

ASSY

Alternating Current

Automatic Document Feeder

Application Specific Integrated Circuit

Assembly

AP

AC

Access Point

Alternating Current

BLDC Motor Brushless DC Motor

BIOS Basic Input Output System

CLBP

CMOS

Color Laser Beam Printer

Complementary Metal Oxide

Semiconductor

CMYK

CN

CON

CPU

Cyan, Magenta, Yellow, Black

Connector

Connector

Central Processing Unit

CTD Sensor Color Toner Density Sensor

CCD Charge Coupled Device

CRUM dB

Customer Replaceable Unit Memory decibel decibelampere decibel milliwatt direct current

Diagnostic Control Unit

Dot Per Inch

Dynamic Random Access Memory

Digital Voltmeter

Dot Per Inch

Dynamic Random Access Memory

Enhanced Capability Port

IEEE lb

ICC

IOT

IPA

I/F

I/O

IC

IDE

GDI

GND

GIF

HBP

HDD

HV

HVPS

HTML

EMI

EP

EPP

FCOT

F/W

FCF/FCT

FISO

FPOT

EEPROM Electronically Erasable Programmable

Read Only Memory

Electro Magnetic Interference electrophotographic

Enhanced Parallel Port

First Copy Out Time firmware

First Cassette Feeder/First Cassette Tray

Front-In, Side-Out

First Print out Time graphics device interface ground

Graphic Interchange Format

Host Based Printing

Hard Disk Drive high voltage

High Voltage Power Supply

Hyper Text Transfer Protocol interface

Input and Output integrated circuit

Intelligent Drive electronics or Imbedded

Drive Electronics

Institute of Electrical and Electronics

Engineers. Inc

Pound(s)

International Color Consortium

Image Output Terminal (Color printer,

Copier)

Isopropy Alcohol

1

1-2

Service Manual

Samsung Electronics

Reference Information

Ping

PPD

PPM

PS

PCL5Ce

PCL6

PDF

PDL

IPM

IPC

NIC

NPC

OPC

PBA

PCL

MHz

MPBF

MPF/MPT

NVRAM

LED

LSU

MB

MFP

ITB

LAN

LBP

LCD

PDL

PPM

PCL

PCI

Images Per Minute

Inter Process CommunicationEPP

Enhanced parallel Port

Image Transfer Belt local area network

Laser Beam Printer

Liquid Crystal Display

Light Emitting Diode

Laser Scanning Unit

Megabyte

Multi-Functional Product

Megahertz

Mean Prints Between Failure

Multi Purpose Feeder/Multi Purpose Tray

Nonvolatile random access memory

Network Interface Card

Network Printer Card

Organic Photo Conductor

Printed Board Assembly

Printer Command Language , Printer

Control Language

Page Discription Language

Page Per Minute

Printer Command Language , Printer

Control Language

Peripheral Component Interconnect by

Intel 1992/6/22, is a local bus standard developed by Intel and introduced in April,

1993 : A60, B60 Pins

Printer Command Language 5Ce-Color

Printer Command Language 6

Portable Document Format

Page Description Language

Packet internet or Inter-Network Groper

Postscript Printer Discription

Page Per Minute

Post Script

TBD

T1

T2

TRC

SRS

SURF

SW

Sync

PnP

U.I.

URL

USB

VCCI

SMPS

SPGP

SPL

SPL-C

Spool

PS3

PTL

PTB

PWM

Post Script Level3

Pre-Transfer Lamp

Paper-Transfer Belt

Pulse Width Moduration

Q’tyQuantity

RAM Random Access Memory

RCP

ROM

SCF/SCT

Remote Control Panel

Read Only Memory

Second Cassette Feeder/Second

Cassette Tray

Switching Mode Power Supply

Samsung Printer Graphic Processor

Samsung Printer Language

Samsung Printer Language-Color

Simultaneous Peripheral Operation Online

WECA

Wi-Fi

Software Requirment Specification

Surface Rapid Fusing

Switch

Synchronous or Synchronization

To Be Determined

ITB

Transfer Roller

Toner Reproduction Curve

Universal Plug and Play

User Interface

Uniform Resource Locator

Universal Serial Bus

Voluntary Control Council for Interference

Information Technology Equipment

Wireless Ethernet Compatibility Alliance

Wireless Fidelity

Samsung Electronics

Service Manual

1

1-3

Reference Information

1

1

.3 Select a location for the printer

• Leave enough room to open the printer trays, covers, and allow for proper ventilation. (see diagram below)

• Provide the proper environment :

- A firm, level surface

- Away from the direct airflow of air conditioners, heaters, or ventilators

- Free of extreme fluctuations of temperature, sunlight, or humidity

- Clean, dry, and free of dust

1

1-4

Service Manual

Samsung Electronics

1

1

.4 A4 ISO 19752 Standard Pattern

This test page is reproduced at 70% of the normal A4 size

Reference Information

Samsung Electronics

Service Manual

1

1-5

Reference Information

1

1

.5 Wireless LAN

• This product uses a printing function with a wireless LAN, which is an option.

- The wireless LAN function uses a frequency instead of connecting LAN cable to connect data to an access point for print.

- For a wireless LAN connection, an AP is needed, It is possible to use wireless LAN onnection with wired LAN. Also, if AP is installed in an office or at home, the wireless LAN function can be simply used.

• Types of desk top PC (or Lap top) that uses the wireless LAN.

Division

CPU

MEMORY

VIDEO CARD

OS

INTERFACE CARD

Basic type Recommend type

Over PENTIUM 233M

Over 64MB

Over 800X600

Over WINDOWS 98

PENTIUM 300MHz

Over 128MB

Over 1024X768

Over WINDOWS ME

A product has a certificated mark of Wi-Fi TM

• About the certificated mark of Wi-Fi TM

- The Wi-Fi TM is a registered trademark of WECA (Wireless Ethernet

Compatibility Alliance). Over 50 of a wireless LAN companies are member of it. The most of main wireless networking companies are attending and the main companies are Lucent technologies, Cisco, Intel/Symbol, 3Com,

Enterasys (Cabletron), Compaq, IBM, Nokia, Dell, Philips, Samsung electronic, Sony, Intersil, and so on. This mark certifies mutual compatibility among product has Wi-Fi a wireless LAN market.

TM (IEEE 802.1) and it is certified as a standard of

1

1-6

Service Manual

Samsung Electronics

ELECTRONICS

* This service manual is a property of Samsung Electronics Co., Ltd.

Any unauthorized use of Manual can be punished under applicable international and/or domestic law.

Samsung Electronics Co.,Ltd. September. 2006

Printed in Korea.

VERSION NO. : 1.00

CODE : JC-0175 C