Control Valve Drive Part List For

Add to My manuals
37 Pages

advertisement

Control Valve Drive Part List For | Manualzz

Owners Manual

Installation Instructions

For Models

PTUF-5600-10

PTUF-5600-13

Table of Contents

Subject Page

System Overview

Pre Installation

6

7

Installation 8

Installing 10

Brine 11

Water On 13

Post Installation 14

Maintaining 14

Information Notes 15

16

Control Drive

Control Valve Drive Parts List

Control Valve Drive Assembly for Clock or Meter

Control Valve Drive Parts List for Clock or Meter

18

19

20

Page 2

P.O. Box 730486

Ormond Beach, FL 32173-0486

1-888-989-(PURE) 7873 Office • 1-877-219-(PURE) 7873 Fax

Copyright© 2003 all rights reserved

Tech Support: 1-888-989-7873

PURE WATER TREATMENT, INC.

Service Instructions

Warranty

Notes

Table of Contents

Subject Page

Meter Start-up

Metered Control Valve Drive Assembly

Metered Control Valve Drive Parts Lists

Bypass Assembly,

22

23

24

Meter Assembly 27

Bypass 28

Assembly 29

32

36

37

Page 3

P.O. Box 730486

Ormond Beach, FL 32173-0486

1-888-989-(PURE) 7873 Office • 1-877-219-(PURE) 7873 Fax

Copyright© 2003 all rights reserved

Tech Support: 1-888-989-7873

PURE WATER TREATMENT, INC.

TO DRAIN

PURE TECH 2200 FLOW DIAGRAM

PURE TECH 2200

Page 4

RAW WATER

Tech Support: 1-888-989-7873

CLEAN WATER

Figure A

PURE WATER TREATMENT, INC.

Job Specification Sheet

• JOB NO. _________________________________________________________

• MODEL NO. ______________________________________________________

• WATER TEST _____________________________________________________

• CAPACITY PER UNIT ____________ MAX. __________ PER REGENERATION

• MINERAL TANK SIZE DIA. _______ HEIGHT ________

• BRINE TANK SIZE & SALT SETTING PER REGENERATION:

• CONTROL VALVE SPECIFICATIONS:

Type of Timer

A) Std

B) *L*

C) 7 Day E) Meter, Std.

D) 12 Day F) Meter, Ext.

Day/Time of Regeneration

Drain Line Flow Control _____________

Brine Refill Rate ___________________ gpm gpm

Injector Size _______________________

Meter Gallon Setting ________________ gal.

TYPICAL CONTROL VALVE INFORMATION

Tank

Dia.

Injector Inj.

Color

Draw/Slow Rinse Rate

(gpm)*

BLFC

**

DLFC

***

6”

7”

8”

9”

10”

12”

#0

#0

#1

#1

#1

#2

Red

Red

White

White

White

Blue

.28 gpm/ .31 gpm

.28 gpm/ .31 gpm

.38 gpm/ .45 gpm

.38 gpm/ .45 gpm

.38 gpm/ .45 gpm

.56 gpm/ .84 gpm

.5 gpm

.5 gpm

.5 gpm

.5 gpm

.5 gpm

1.0 gpm

1.2 gpm

1.2 gpm

1.5 gpm

2.0 gpm

2.4 gpm

3.5 gpm

13”

14”

16”

#2

#3

#3

Blue

Yellow

Yellow

.56 gpm/ .84 gpm

.63 gpm/ 1.0 gpm

.63/ gpm/ 1.0 gpm

1.0 gpm

1.0 gpm

1.0 gpm

4.0 gpm

5.0 gpm

7.0 gpm

Due to varying water conditions, tank sizes and water pressures, the above settings should be used only as a guideline.

** B.L.F.C. (Brine Line Flow Control). Refill Rate for Filling Brine Tank.

*** D.L.F.C. (Drain Line Flow Control). Backwash and Rapid Rinse Flow Rates.

Page 5

Tech Support: 1-888-989-7873

PURE WATER TREATMENT, INC.

System Overview

• This installation guide gives a step by step, start to finish procedure for installing

PURE TECH 2200 systems using Fleck valves. All of these systems will regenerate with softener Solar Salt or Potassium Chloride.

• Your new system from the PURE WATER TREATMENT, INC. comes with an owner/service manual, which, is enclosed along with these instructions, and will help explain all necessary details required for successful installation and operation of your system. Please refer to these instructions and the service manual supplied with your system during installation and programming.

• All steps provided herein are for typical installations only. If you require additional plumbing to install your system, simply contact a person who is knowledgeable in residential plumbing or have a local plumbing company help you install, or install the system for you.

• There is a bit of "over-kill" in our instructions, but please bear with us as we want to ensure that you, our customer, fully understand the instructions and are completely satisfied with your installation!

• We recommend that you take a few minutes and look at the service/parts manual for your particular model, to help you better understand your new water system. Take your time and carefully read the instructions.

• Get all of your plumbing parts together before you start, and have an assistant help you, if possible. Typical installation should take no more than a few of hours.

• If you are going to turn the water off to your house while installing the system, we recommend that you turn off the electricity to your electric water heater during installation. After the system is installed with water running through it, turn on a few hot and cold-water faucets, and let them run until there is no more air in your lines, then turn the electricity back on to your water heater.

• Our systems can safely handle a pressure range of 35-95 psi. However, as with most residential plumbing and for best operation causing the least wear on critical parts, we recommend an operating range of 40-65psi. Now all you have to do is plumb in the system, plug it in and set the current time of day!

Page 6

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Pre Installation

Your system should be located in a protected, dry, level and non-freezing area. The brine tank and resin tank can have as much as 20 feet of 3/8" brine tubing connecting them. So, the brine tank can set several feet from the resin tank. The brine tank will hold 240lbs of softener Solar Salt or Potassium Chloride, so be sure to make it accessible for filling the tank when needed.

We recommend a ½" drain for the regeneration/backwashing cycles. If possible, the house drain should be no farther than 20 feet from the system. You will also need to purchase some flexible ½" inside diameter, plastic tubing from a local hardware or building supply store. This same size tubing will be used for both the valve drain fitting, and on your brine tank safety overflow fitting. (Always follow local plumbing codes).

You will need a standard 3-prong, 120V, grounded outlet that is not controlled by a switch. Our Fleck valves have a 5' power cord, but you can use an extension cord if an outlet is not nearby. Please follow any local building/safety codes if you need to use an extension cord.

IMPORTANT NOTE ! IF you decide to set the brine tank in your garage, remember that the water inside the brine tank will not freeze, but the water in the small 3/8" plastic water line running from the system valve to the brine tank will. Make certain the garage is warm enough to prevent this line from freezing!

Make a list of all the plumbing fittings you will need to completely install the system to make it ready for operation.

Assemble all tools needed to install the system, and start your installation! •

Tools and Materials needed

1) Pipe Cutters

2) PVC Glue

3) PVC, copper or CPVC pipe

4) Two 1” or ¾” male adapters—Depending on which bypass is ordered.

Page 7

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Installation

1.

Turn off the main water shutoff valve.

2.

3.

Next, open all plumbing fixtures in the house including all outside faucets in order to drain the lines of all water possible.

Cut and remove a section of the main incoming water line near where the system is to be installed. Allowing this line to drain thoroughly.

4. Remove the yoke (or optional bypass valve) from the back of the tank valve by loosening the two small stainless steel clamps on either side of the rear valve assembly, that holds it in place. Then simply pull it off the back of the valve. Now that you have the yoke or bypass valve removed, follow the directions below to make them ready to install on the valve.

5. INSTRUCTIONS FOR USING A YOKE. If you have a standard Noryl Plastic yoke, it will have two ¾" or 1" male thread nipples, (one inlet & one outlet). You will need to buy two ¾" or 1" Female thread adapters to whatever type and size of piping you are plumbing the system to.

6. INSTRUCTIONS FOR USING A BYPASS. If you are using our optional ¾" or 1" brass bypass valve, you will need to purchase two ¾" or 1" Male thread adapters to whatever type and size pipe you are plumbing to.

7. If you are going to use copper piping and be soldering joints, we do not recommend applying intense heat, to your new valve/meter assembly. We always recommend that you remove the yoke or bypass from the valve assembly, and attach your plumbing adapters to the yoke or bypass away from the valve. This simple step will ensure that you are not applying any heat as you solder or pressure as you tighten the adapters onto the yoke/bypass, while they are mounted on the valve body itself.

8. Another tip if you are using copper adapters. Always solder a 3" to 5" piece of copper pipe into each of the two pipe adapters away from the valve, then let them cool off before threading each one onto the yoke or bypass valve.

9. After they cool off, apply Teflon tape to the male threads of the Noryl yoke, (or onto the male adapters for the brass bypass valve), and securely tighten them to the yoke or bypass valve. Again, doing this before you re-attach them back onto the rear of the valve/meter body assembly.

Page 8

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Installation Cont.

11. Important!! WE DO NOT recommend connecting adapters to either the yoke or bypass valve, while the yoke or bypass valve is connected to the Valve/Meter assembly!

You may exert too much pressure on the valve while securing the adapters, causing damage to the valve housing!)

12.

After all soldering is finished and the adapters are securely threaded onto either the yoke or the brass bypass valve assembly, then attach the yoke or bypass valve back onto the valve/meter assembly and secure it with the two small stainless steel clamps.

13. Now position your conditioning system in place for the final water line installation.

14. Remember; if you are using our optional brass bypass valve, make certain the bypass valve is set in the "Service" position, while soldering the pipes to the system. Then return it to the "Bypass" position before turning your water back on to the house.

15. Measure and cut the lengths of pipe you need to plumb the main hard water line into your system. Then do the same for the conditioned water line that will exit from the system, back out into the house.

16. *NOTE* As you look directly into the two holes in your Fleck valve, the hard water line will always enter the hole on the LEFT SIDE of the yoke or bypass valve assembly. The valve body also has an arrow stamped into each side, showing the direction of flow.

17. If you use our optional bypass valve, arrows indicating water flow direction are printed on the top of the bypass valve assembly.

18. Just remember, that as you are looking directly into the two holes where the water enters and exits the valve, the hard water line from your house always enters the hole on the LEFT. The conditioned water flowing out from the system, back into your house is always the hole on the RIGHT.

19.

If you purchased a Meter On Demand Water Softener, you will need to make sure the gold-tipped black cable protruding from the valve is securely plugged into the domed shaped portion of the rear of the valve.

Page 9

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Installing the Drain Line to the Valve

1.

2.

(All of our Fleck valves have a drain hose barb, generally located on the lower, backside or side of the valve. First, check to make certain this drain hose barb is securely threaded into the valve body and that the threads have been sealed with Teflon tape.

Once you know the drain hose barb is installed properly, carefully push the 1/2" ID plastic drain hose completely over the barbed end of the fitting, and then attach a small hose clamp to the end of the line so it cannot work loose over time. Run the opposite end of this drain hose to the drain you are going to use for your system. Remember to leave a small air gap at the end of the hose going to the house drain.

(Follow local plumbing codes), and secure it there.

3. When the system is in the backwash/regeneration mode, water will flow out of this drain line with a fair amount of pressure, especially during the "rapid rinse phases" of the process, and the line may sometimes "jump" a little when changing cycles.

Page 10

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Brine Tank Connection

1.

2.

Next, connect your brine tank to your system. One end of the supplied 3/8" brine line tubing will be connected to your brine tank and the opposite end needs to be connected to your Fleck valve.

Look inside your brine tank and you will see a 4" diameter "Brine Well" tube. Remove the lid off the top of the brine well and look inside this tube. Here you will find the "Brine Float" assembly. The brine float assembly works like a toilet tank float, shutting the water off inside the brine tank should the level of water get too high.

3. Check to see if the brine float assembly is loose inside the brine well tube. If it is, simply pull it up out of the brine well and look about 2" down from the top of the brine float assembly where you will see the metal end of a small threaded screw sticking out about ½". There will be a small black plastic nut threaded on it. Remove the black nut and then put the brine float back into the brine well. Notice there is a small hole drilled in the brine well, that you can insert this small section of screw through.

4. Hold the brine float with the section of screw in the hole as you put the small black nut back on. This is what holds the brine float in place.

5. On top of the brine float, you will see a larger black elbow with a black plastic nut.

Carefully remove the black nut and you will find two small compression rings inside the nut, one black and one white. These small pieces help seal the end of the 3/8" tube that connects the brine tank with the valve on top of the system.

6. Each one of these small rings has a flat side. Hold the two small rings together with the flat sides touching. This is the way they fit together when they go inside the black nut, white piece first.

7. Next, insert one end of the 3/8" tubing though the hole in the side of the brine tank and brine well, and slide the black nut onto the tube with the threads facing the end of the tube. Then, slide the two small compression rings onto the tube, white piece first, then the black piece making sure the flat edges of both rings are together.

8.

Now insert the end of the tube into the black elbow as far as it will go. Hold it there as you thread the black nut onto the black elbow, tightening it finger tight which compresses the two rings inside the nut onto the tubing.

9. Replace the lid on the top of the brine well! Your brine tank is now ready to be connected to the Fleck valve.

10.

Take the other end of the 3/8" brine tube and find the 3/8" brass nut located on the valve body of your system. Remove this brass nut and you will find a small plastic compression ring inside.

Page 11

Tech Support: 1-888-989-7873

PURE WATER TREATMENT, INC.

Brine Tank Connection Cont.

11. Slide the brass nut over the end of the tube, threads facing the end of the tube. Then slide the compression ring on with the narrow side facing the end of the tube.

12.

Insert the end of the tube fully into the opening on the valve where the brass nut was located, then slide the compression ring and brass nut up the tube, finally threading the brass nut back onto the threads. Tighten the brass nut gently with a small wrench.

13.

Notice the plastic elbow that is located on the side of your brine tank. This is a

"Safety Overflow", and will use the same size drain line that is used on the valve drain (1/2" ID flexible plastic line). This drain line will not be under pressure, so it must be directed to a drain that is physically lower than it is. DO NOT connect this drain line into the drain line coming from the Fleck valve! It must be run separately to the drain.

14. Fill the brine tank with 9 gallons of water.

15.

Add 240 lbs of "Solar Salt" or "Potassium Chloride" to the brine tank, and you are now ready to turn the water back on!

Page 12

Tech Support: 1-888-989-7873

PURE WATER TREATMENT, INC.

Turning the Water Back On

1. INSTRUCTIONS FOR USING A BYPASS VALVE. If you are using a bypass valve, make sure your bypass valve is now in the "BYPASS" position.

2. Turn your water on slowly, leaving all your faucets in the house open until water starts coming out of them. After they are all running steady and the air is out of the water lines, turn them off one by one. The raw water will be bypassing your system at this time.

3. Slowly open your bypass valve to the “SERVICE” position and begin filling the softener resin tank with water. In a few minutes the sound of water entering the system will stop.

4. Next, open one faucet, (preferably an outside faucet, a laundry sink or bathtub), letting the water run through it slowly for a few minutes. This allows the water to rinse the inside of your resin tank out and settle the media.

5. Sometimes you may experience some light/medium brown color rinsing off the new resin beads..... This is normal...and should only last a few minutes.

6. This is why we suggest running the water through only one faucet, to clear the softener of this colored water.

7. After a few minutes, and the water is running clear.....turn the faucet off.

8. You now have soft water on your cold water side.... The hot water will take a couple of days to become soft, as your hot water tank is full of hard water.

9. Finally, if you are using a demand valve firmly insert the small brass end of the black

Meter Cable, into the small hole located on top of the dome shaped Meter housing.

The end of the cable will only insert about 1/8" - 3/16" into the meter housing hole.

Page 13

Tech Support: 1-888-989-7873

PURE WATER TREATMENT, INC.

Post Installation

1.

We will have already pre-set the meter on the system to regenerate, according to your water test results. You will only need to set the time of day on the front of the valve.

If you are not sure what the meter is supposed to be set on, please give us a call with information on your water test results, and we will help you determine what setting to place your meter on.

2.

3.

Look in your service manual, for your particular model Fleck valve, and manually run your valve through a regeneration cycle. To do this, simply turn the manual "Regen" dial clockwise just a few "clicks" at a time, stopping at each setting for a minute, to clear the air out of the resin tank and valve. Once you have completed turning the

"Regen" knob one complete revolution and it is set back to the "Service" position, the system is now ready for use!

Finally, plug the valve in the electrical outlet and set the current time of day. Our systems will regenerate around 2:00am.

4.

5.

Check all connections for leaks.

You are now ready to experience PURE WATER!

Don’t forget to tell your friends, family and neighbors about how excellent the

PURE TECH 2200 works for you.

Page 14

Maintaining Your System

The system is set to use about 9-lbs. of salt or potassium per regeneration cycle. For the next few months, monitor the brine tank to establish how often to add salt or potassium.

If your system has a timed valve, you should have to fill the brine tank about every 5 to 6 weeks. If your system is metered, it may be less often based on water usage and the meter setting for your water.

The system will manually regenerate itself clean. If you find that the system is not producing enough clean water, then set the ‘regen’ pins to regenerate more often.

If the system doesn’t seen to be pulling any brine solution in, check the screen in the brine line at the base of the valve. It may be clogged and need cleaning.

Tech Support: 1-888-989-7873

PURE WATER TREATMENT, INC.

Information Notes

Page 15

• Even though you now have PURE WATER in your cold water lines, your water heater is still full of raw water. Through normal use, this water will be replaced with soft water in about 2 to 3 days.

• You may experience cloudy water in the mornings. This is caused by the clean water sitting in your pipes over night and stripping the build up off. Run your water for 2 to

3 minutes every morning until it clears. This should last no longer than 1 to 2 weeks.

• We supply a toll free number (888-989-7873), to all of our customers to use, in case they don't understand something contained in our installation instructions.

• Be sure to cut back on your detergent, soap and shampoo usage! Generally, you should be able to cut your soap use in half!

• Hard copper pipe generally comes in two types. Use the thicker "L" type copper pipe rather than thinner "M" type copper pipe.

• Follow your local plumbing and building codes when installing our systems.

• Please Email us a picture of your installed system!! Let us see how good of a job you did on the installation. [email protected]

Tech Support: 1-888-989-7873

PURE WATER TREATMENT, INC.

Start-up Procedure

Page 16

The water softener should be installed with the inlet, outlet and drain connections made in accordance with manufacturer’s recommendations and to meet applicable plumbing codes.

1. Manually index the softener control into the service position and let water flow into the resin tank. When the water flow stops, open a softened water tap until all air is released from the lines, then close the tap.Note: the various regeneration positions may be dialed manually by turning the knob on the front of the control until the indicator shows that the Aoftener is in the desired position.

2. Manually index the control to the backwash position and allow water to flow at the drain for 3 or 4 minutes.

3. Remove back cover plate.

4. Make sure that the salt dosage is set as recommended by the manufacturer. If necessary, set salt in accordance with the setting instruction sheet. Manually index the control to the brine fill position and allow the brine tank to fill to the top of the air check.

5. Manually index the control to the brine draw position and allow the control to draw water from the brine tank until it stops.

6. Plug in the electrical cord and look in the sight hole in the back of the motor to see that it is running. Set the days that regeneration is to occur by sliding tabs on skipper wheel outward to expose trip fingers. Each tab is one day. Finger at red pointer is tonight. Moving clockwise from red pointer, extend or retract fingers to obtain the desired regeneration schedule.

7. Manually advance the control to the beginning of the brine fill position; and allow the control to return to the service position automatically.

8. Fill the brine tank with salt.

9. Replace back cover on the control.

10. Make sure that any by-pass valving is left in the normal service position.

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Control Valve Drive Assembly

Page 17

Part List

Item No. No. Req’d Part No. Description

1. . . . . . . . . . 1 . . . . . . . . . 14448-010 . . . . . . . Housing - w/Pin

1 . . . . . . . . . 14448-011 . . . . . . . Housing - w/Pin Drilled for Screw

1 . . . . . . . . . 14448-012 . . . . . . . Housing - w/Pin Drilled for Thumb Screw

1A . . . . . . . . . 1 . . . . . . . . . 15494-01 . . . . . . . . “L” Housing - w/Pin

1 . . . . . . . . . 15494-03 . . . . . . . . “L” Housing - w/Pin Drilled for Designer

2. . . . . . . . . . . 1 . . . . . . . . . 13175. . . . . . . . . . . Motor Mounting Plate

3. . . . . . . . . . . 1 . . . . . . . . . 18743. . . . . . . . . . . Motor - 120V., 60 Hz.

1 . . . . . . . . . 19659. . . . . . . . . . . Motor - 24V., 60 Hz.

4. . . . . . . . . . . (2-3) . . . . . . 11384. . . . . . . . . . . Screw - Motor Mtg. & Ground Wire

5. . . . . . . . . . . (3-5) . . . . . . 13296. . . . . . . . . . . Screw - Component Mounting

Tech Support: 1-888-989-7873

PURE WATER TREATMENT, INC.

Control Valve Drive Part List Cont.

Item No. No. Req’d Part No. Description

6. . . . . . . . . . . 1 . . . . . . . . . 13017. . . . . . . . . . . Idler Gear

7. . . . . . . . . . . 1 . . . . . . . . . 13018. . . . . . . . . . . Idler Pinion

8. . . . . . . . . . . 1 . . . . . . . . . 13312. . . . . . . . . . . Spring - Idler

9. . . . . . . . . . . 1 . . . . . . . . . 13164. . . . . . . . . . . Drive Gear

11 . . . . . . . . . 1 . . . . . . . . . 13170. . . . . . . . . . . Main Gear & Shaft

12 . . . . . . . . . 1 . . . . . . . . . 19205. . . . . . . . . . . 24 Hour Gear Assembly, Silver

1 . . . . . . . . . 19205-01 . . . . . . . . 24 Hour Gear Assy, Tan

13 . . . . . . . . . 1 . . . . . . . . . 13011. . . . . . . . . . . Cycle Actuator Gear

14 . . . . . . . . . 1 . . . . . . . . . 14177. . . . . . . . . . . Knob - Manual Regeneration

15 . . . . . . . . . 4 . . . . . . . . . 13300. . . . . . . . . . . Ball - 1/4″ Dia.

16 . . . . . . . . . 2 . . . . . . . . . 13311. . . . . . . . . . . Spring - Detent - Skipper Wheel

19 . . . . . . . . . 1 . . . . . . . . . 14381. . . . . . . . . . . Skipper Wheel Assembly - 12 Day

1 . . . . . . . . . 14860. . . . . . . . . . . Skipper Wheel Assembly - 7 Day

20 . . . . . . . . . 1 . . . . . . . . . 13864. . . . . . . . . . . Skipper Wheel Ring

21 . . . . . . . . . 2 . . . . . . . . . 14457. . . . . . . . . . . Spring - Detent - Main Gear

22 . . . . . . . . . 1 . . . . . . . . . 13014. . . . . . . . . . . Regeneration Pointer

23 . . . . . . . . . 1 . . . . . . . . . 11842. . . . . . . . . . . Electrical Cord - Standard

24 . . . . . . . . . 2 . . . . . . . . . 12681. . . . . . . . . . . Wire Connector (Not Shown)

25. . . . . . . . . . 1 . . . . . . . . . 13547. . . . . . . . . . . Strain Relief

26. . . . . . . . . . 1 . . . . . . . . . 13229. . . . . . . . . . . Back Cover

27. . . . . . . . . . 1 . . . . . . . . . 13309. . . . . . . . . . . Front Label - Brown on Beige

1 . . . . . . . . . 13437. . . . . . . . . . . Front Label - Blue/Silver on Black

28. . . . . . . . . . 1 . . . . . . . . . 13310. . . . . . . . . . . Rear Label - Softener

1 . . . . . . . . . 18520. . . . . . . . . . . Rear Label - Filter

29. . . . . . . . . . 1 . . . . . . . . . 13348. . . . . . . . . . . Tape Stripe - Brown on Beige

1 . . . . . . . . . 13436. . . . . . . . . . . Tape Stripe - Blue on Silver

30 . . . . . . . . . 1 . . . . . . . . . 60514. . . . . . . . . . . Brine Cam Assy., 3-18

1 . . . . . . . . . 60514-0 . . . . . . . . . Brine Cam Assy., 6-36

1 . . . . . . . . . 60514-0 . . . . . . . . . Brine Cam Assy. - Minutes

34 . . . . . . . . . 2 . . . . . . . . . 12473. . . . . . . . . . . Screw-Drive Mounting

35 . . . . . . . . . 1 . . . . . . . . . 12037. . . . . . . . . . . Washer

37 . . . . . . . . . 1 . . . . . . . . . 15151. . . . . . . . . . . Screw - Knob

38 . . . . . . . . . 1 . . . . . . . . . 14176. . . . . . . . . . . Valve Position Dial - Standard

1 . . . . . . . . . 14278. . . . . . . . . . . Valve Position Dial - Low Water

1 . . . . . . . . . 15478. . . . . . . . . . . Valve Position Dial - Chemical Filter

1 . . . . . . . . . 16715. . . . . . . . . . . Valve Position Dial - Filter

39. . . . . . . . . . 1 . . . . . . . . . 14175. . . . . . . . . . . Knob Label - Beige

1 . . . . . . . . . 14207. . . . . . . . . . . Knob Label - Silvers

40 . . . . . . . . . 1 . . . . . . . . . 40214. . . . . . . . . . . Screw, Brine Cam

Page 18

Tech Support: 1-888-989-7873

PURE WATER TREATMENT, INC.

Control Valve Drive Assembly For (Clock Or Meter)

Page 19

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Control Valve Drive Part List For (Clock Or Meter)

Item No. No. Req’d Part No. Description

1 . . . . . . . . . 2-4 . . . . . . . .13255 . . . . . . . . . . . Adapter Clip (clock or meter)

2 . . . . . . . . . 5 . . . . . . . . .13242 . . . . . . . . . . . Seal

5 . . . . . . . . .17772 . . . . . . . . . . . Silicone Seal

3 . . . . . . . . . 1 . . . . . . . . .61400-12 . . . . . . . .Valve Body Assembly - 1″ Dist.

1 . . . . . . . . . 61400-11 . . . . . . . . Valve Body Assembly - 3/4″ Dist.

4. . . . . . . . . 1 . . . . . . . . .13304 . . . . . . . . . . . O-Ring - Distributor Tube - 1″

1. . . . . . . . . .10244 . . . . . . . . . . . O-Ring - Distributor Tube - 13/16″

5 . . . . . . . . . 1 . . . . . . . . .12281 . . . . . . . . . . . O-Ring - Top of Tank

6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Not Assigned

7 . . . . . . . . 4 . . . . . . . . . .14241 . . . . . . . . . . . Spacer

8. . . . . . . . . 1 . . . . . . . . . .13247 . . . . . . . . . . . Piston - Standard

1 . . . . . . . . . .13781 . . . . . . . . . . . Piston - Low Water

1 . . . . . . . . . .13852 . . . . . . . . . . . Piston - Filter

9. . . . . . . . . 1 . . . . . . . . . .10696 . . . . . . . . . . . Piston Pin

10. . . . . . . . 1 . . . . . . . . . .13001 . . . . . . . . . . . Piston Rod Assembly

11. . . . . . . . 1 . . . . . . . . . .12953 . . . . . . . . . . . Piston Retainer

12. . . . . . . . 1 . . . . . . . . . .13446 . . . . . . . . . . . End Plug Assembly Std. - White

1 . . . . . . . . . .13446-10 . . . . . . . . End Plug Assembly Filter - Black

1 . . . . . . . . . .13446-20 . . . . . . . . End Plug Assembly Low Water - Gray

14. . . . . . . . 2 . . . . . . . . . .13315 . . . . . . . . . . . Screw- Injector Mounting

*15 . . . . . . 2 . . . . . . . . . .19228 . . . . . . . . . . . Adapter Coupling

*16. . . . . . . 4 . . . . . . . . . .13305 . . . . . . . . . . . O-Ring- Adapter Coupling

*17. . . . . . . 2-4. . . . . . . . .13314 . . . . . . . . . . . Screw- Adapter Coupling (clock or meter)

18 . . . . . . . 1 . . . . . . . . . .12638 . . . . . . . . . . . O-Ring - Drain

19. . . . . . . . 2 . . . . . . . . . .13301 . . . . . . . . . . . O-Ring - Injector

20. . . . . . . . 2 . . . . . . . . . .13302 . . . . . . . . . . . O-Ring - Brine Spacer

21. . . . . . . . 1 . . . . . . . . . .13303 . . . . . . . . . . . O-Ring - Injector Cover

22. . . . . . . . 1 . . . . . . . . . .13163. . . . . . . . . . . . Injector Body

23. . . . . . . . 1 . . . . . . . . . .10913U . . . . . . . . . . Injector Nozzle - Undrilled

24. . . . . . . . 1 . . . . . . . . . .10914. . . . . . . . . . . . Injector Throat - Specify Size

25. . . . . . . . 1 . . . . . . . . . .10227. . . . . . . . . . . . Injector Screen

26. . . . . . . . 1 . . . . . . . . . .13166. . . . . . . . . . . . Injector Cover

27. . . . . . . . 1 . . . . . . . . . .13172. . . . . . . . . . . . Brine Valve Stem

28. . . . . . . . 1 . . . . . . . . . .12626. . . . . . . . . . . . Brine Valve Seat

29. . . . . . . . 1 . . . . . . . . . .13165. . . . . . . . . . . . Brine Valve Cap

30. . . . . . . . 1 . . . . . . . . . .13167. . . . . . . . . . . . Brine Valve Spacer

31. . . . . . . . 1 . . . . . . . . . .12550. . . . . . . . . . . . Quad Ring

32. . . . . . . . 1 . . . . . . . . . .11973. . . . . . . . . . . . Spring - Brine Valve

33. . . . . . . . 1 . . . . . . . . . .16098. . . . . . . . . . . . Washer - Brine Valve

34. . . . . . . . 1 . . . . . . . . . .11981-01 . . . . . . . . . Retaining Ring

35. . . . . . . . 1 . . . . . . . . . .10329 . . . . . . . . . . . B.L.F.C. Fitting Nut

36. . . . . . . . 1 . . . . . . . . . .10330 . . . . . . . . . . . B.L.F.C. Ferrule

37. . . . . . . . 1 . . . . . . . . . .10332 . . . . . . . . . . . B.L.F.C. Tube Insert

Page 20

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Control Valve Drive Part List For (Clock Or Meter)

Item No. No. Req’d Part No. Description

38. . . . . . . . 1 . . . . . . . . . .12094 . . . . . . . . . . . B.L.F.C. Button - .25 GPM

1 . . . . . . . . . .12095 . . . . . . . . . . . B.L.F.C. Button - .5 GPM

1 . . . . . . . . . .12097 . . . . . . . . . . . B.L.F.C. Button - 1.0 GPM

39. . . . . . . . 1 . . . . . . . . . .12977 . . . . . . . . . . . O-Ring - B.L.F.C.

40. . . . . . . . 1 . . . . . . . . . .13245 . . . . . . . . . . . B.L.F.C. Button Retainer

41. . . . . . . . 1 . . . . . . . . . .13244 . . . . . . . . . . . B.L.F.C. Fitting, 3/8″

42. . . . . . . . 1 . . . . . . . . . . . . . . . . . . . . . . . . . . D.L.F.C. Button - Specify Size

43. . . . . . . . 1 . . . . . . . . . .13173 . . . . . . . . . . . D.L.F.C. Button Retainer

44. . . . . . . . 1 . . . . . . . . . .12767 . . . . . . . . . . . Screen - Brine Line

45. . . . . . . . 1 . . . . . . . . . .15348 . . . . . . . . . . . O-Ring - D.L.F.C. (not shown)

46. . . . . . . . 1 . . . . . . . . . .13497 . . . . . . . . . . . Air Disperser

47 . . . . . . . 1 . . . . . . . . . .13546. . . . . . . . . . . . End Plug Retainer

48. . . . . . . . 3 . . . . . . . . . .12112 . . . . . . . . . . . Screw

49. . . . . . . . 1 . . . . . . . . . .13363. . . . . . . . . . . . Washer

50. . . . . . . . 1 . . . . . . . . . .13296 . . . . . . . . . . . . Screw

51A . . . . . . 1 . . . . . . . . . .13398 . . . . . . . . . . . . Yoke, Brass, 1″ NPT

1. . . . . . . . . . .13708 . . . . . . . . . . . Yoke, Brass, 3/4″ NPT

51B . . . . . . 1 . . . . . . . . . . . . . . .18706 . . . . . . . . . . . . . . . . . . . . . Yoke, Plastic, 1″ NPT

1 . . . . . . . . . . . . . . .18706-02 . . . . . . . . . . . . . . . . . . Yoke, Plastic 3/4″ NPT

52 . . . . . . . 1 . . . . . . . . . . . . . . .13308 . . . . . . . . . . . . . . . . . . . . . Drain Hose Barb

* Not used with meter controls

Page 21

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Metered Start-up

Page 22

The water softener should be installed with the inlet, outlet and drain connections made in accordance with manufacturer’s recommendations and to meet applicable plumbing codes.

1. Manually index the softener control into the service position and let water flow into the resin tank. When the water flow stops, open a softened water tap until all air is released from the lines, then close the tap. NOTE: The various regeneration positions may be dialed manually by turning the knob on the front of the control until the indicator shows that the softener is in the desired position.

2. Set water usage program wheel using any one of the following procedures:

Typical Residential Application

To program, just set the time, set the hardness and it automatically monitors system needs and regenerates only when necessary. To set time of day press red time set button and turn

24 hour gear until present time of day is at “time of day”. Set program wheel by lifting the

“people” dial and rotating it so that the number of people in the household is aligned with the household grains per gallon water hardness. Release the dial and check for firm engagement at setting. (This method will provide reserve capacity based on 75 gallons per person.)

Optional Programming Procedures

Calculate the gallon capacity of the system, subtract the necessary reserve requirement and set the gallons available at the small white dot on program wheel gear. Note, drawing shows

850 gallon setting. The capacity (gallons) arrow denotes remaining gallons exclusive of fixed reserve.

3. Rotate the program wheel counterclockwise until it stops at regeneration position.

4. Manually index the control to the back-wash position and allow water to flow at the drain for 3 or 4 minutes.

5. Remove back cover plate. Make sure than the salt dosage is set as recommended by the manufacturer. Manually index the control to the brine fill position and allow the brine tank to fill to the top of the air check.

6. Manualy index the control to the brine rinse position and allow the control to draw water from the brine tank until it stops.

7. Plug in the electrical cord and look in the sight hole in the back of the montor to see that it is running.

8. Manually advance the control to the beginning of the brine fill position and allow the control to return to the service position automatically.

9. Fill the brine tank with salt. Replace back cover on the control. Be sure cable is not pinched between cover and housing.

10. Make sure that any by-pass valving is left in the normal service position.

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Metered Control Valve Drive Assembly

Page 23

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Metered Control Valve Drive Part List

Item No. No. Req’d Part No. Description

1 . . . . . . . . . 1 . . . . . . . 14448-000 . . . . . . Housing - with Roll Pin

1 . . . . . . . 14488-001 . . . . . . Housing - w/Pin Drilled for Screw

1 . . . . . . . 14448-0 . . . . . . . . . Housing - w/Pin Drilled for Thumb Screw

1A . . . . . . . 1 . . . . . . . 15494-01 . . . . . . . . “L” Housing - w/Pin

1 . . . . . . . 15494-03 . . . . . . . . “L” Housing - w/Pin Drilled for Designer

2 . . . . . . . . . 1 . . . . . . . 13175. . . . . . . . . . . . Motor Mounting Plate

3 . . . . . . . . . 1 . . . . . . . 18743. . . . . . . . . . . . Motor - 120V., 60 Hz.

1. . . . . . . . 13494. . . . . . . . . . . . Motor - 24V., 60 Hz.

4 . . . . . . . . . 2-3 . . . . . . 11384. . . . . . . . . . . . Screw - Motor Mtg. & Ground Wire

5 . . . . . . . . . 2-4 . . . . . . 13296. . . . . . . . . . . . Screw - Component Mounting

6 . . . . . . . . . 1. . . . . . . . 13017. . . . . . . . . . . . Idler Gear

7 . . . . . . . . . 1. . . . . . . . 13018. . . . . . . . . . . . Idler Pinion

8 . . . . . . . . . 1. . . . . . . . 13312. . . . . . . . . . . . Spring - Idler

9 . . . . . . . . . 1. . . . . . . . 13164. . . . . . . . . . . . Drive Gear

11. . . . . . . . 1. . . . . . . . 13170. . . . . . . . . . . . Main Gear & Shaft

12. . . . . . . . 1. . . . . . . . 19205. . . . . . . . . . . . 24 Hour Gear Assembly, Silver

1. . . . . . . . 19205-01. . . . . . . . . 24 Hour Gear Assy, Tan

13. . . . . . . . 1. . . . . . . . 13802 . . . . . . . . . . . Cycle Actuator Gear

14. . . . . . . . 1. . . . . . . . 14177 . . . . . . . . . . . Knob - Manual Regeneration

15. . . . . . . . 2. . . . . . . . 13300 . . . . . . . . . . . Ball - 1/4″ Dia.

16. . . . . . . . 2. . . . . . . . 14457 . . . . . . . . . . . Spring - Detent

18. . . . . . . . 1. . . . . . . . 13748 . . . . . . . . . . . Screw - Program Wheel

19. . . . . . . . 1. . . . . . . . 60405-15 . . . . . . . . Program Skipper Wheel Assy. - Specify

Hardness Capacity

20. . . . . . . . 1. . . . . . . . 13806 . . . . . . . . . . . Program Wheel Retainer

21. . . . . . . . 1. . . . . . . . 13953. . . . . . . . . . . Cover Label - Program Wheel

22. . . . . . . . 1. . . . . . . . 11842. . . . . . . . . . . Electrical Cord

23. . . . . . . . 2. . . . . . . . 12681. . . . . . . . . . . Wire Connector

24. . . . . . . . 1. . . . . . . . 13547. . . . . . . . . . . Strain Relief

25. . . . . . . . 1. . . . . . . . 13229. . . . . . . . . . . Back Cover

26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Not Assigned

27. . . . . . . . 1. . . . . . . . 13955. . . . . . . . . . . Front Label - Beige

1. . . . . . . . 13958. . . . . . . . . . . Front Label - Silver

28. . . . . . . . 1. . . . . . . . 13310. . . . . . . . . . . Rear Label - Softener

1. . . . . . . . 18520. . . . . . . . . . . Rear Label - Filter

29. . . . . . . . 1. . . . . . . . 13957. . . . . . . . . . . Tape Stripe - Beige

1. . . . . . . . 13960. . . . . . . . . . . Tape Stripe - Silver

30. . . . . . . . 1. . . . . . . . 60514. . . . . . . . . . . Brine Cam Assembly, 3-18

1. . . . . . . . 60514-01. . . . . . . . Brine Cam Assembly, 6-36

1. . . . . . . . 60514-02 . . . . . . . Brine Cam Assembly - Minutes

34. . . . . . . . 2. . . . . . . . 12473 . . . . . . . . . . Screw-Drive Mounting

35. . . . . . . . 1 . . . . . . . 12037. . . . . . . . . . . Washer

37. . . . . . . . 1. . . . . . . . 13830. . . . . . . . . . . Drive Pinion - Program Wheel

38. . . . . . . . 1. . . . . . . . 13831. . . . . . . . . . . Clutch - Drive Pinion

39. . . . . . . . 1. . . . . . . . 14253. . . . . . . . . . . Spring Retainer

Page 24

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Metered Control Valve Drive Part List Cont.

Item No. No. Req’d Part No. Description

40 . . . . . . . . 1. . . . . . . . 14276 . . . . . . . . . . . Spring

41 . . . . . . . . 1. . . . . . . . 14043 . . . . . . . . . . . Cable Assembly, Std

1. . . . . . . . 14910 . . . . . . . . . . . Cable Assembly, Ext, Rt Angle

42. . . . . . . . . 1. . . . . . . . 14176 . . . . . . . . . . . Valve Position Dial - Standard

1. . . . . . . . 14278 . . . . . . . . . . . Valve Position Dial - Low Water

1. . . . . . . . 15478 . . . . . . . . . . . Valve position Dial - Filter

43 . . . . . . . . 1. . . . . . . . 1417. . . . . . . . . . . . Knob Label - Beige

1. . . . . . . . 14207. . . . . . . . . . . Knob Label - Silver

44 . . . . . . . . 1. . . . . . . . 15151. . . . . . . . . . . Screw - Knob

45 . . . . . . . . 1. . . . . . . . 40214. . . . . . . . . . . Screw, Brine Cam

Page 25

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Bypass Valve Assembly, Plastic

Page 26

Item No. No. Req’d Part No. Description

1 . . . . . . . . 1 . . . . . . . . . .19723. . . . . . . . . . . . . By-Pass Valve Body, Plastic

2 . . . . . . . . 1 . . . . . . . . . .11183 . . . . . . . . . . . . .O-Ring, -015

3 . . . . . . . . 1 . . . . . . . . . .19724. . . . . . . . . . . . . Cap, By-Pass

4 . . . . . . . . 2 . . . . . . . . . .17512. . . . . . . . . . . . . Screw, Hex Washer Head, #6-24 x 3

5A. . . . . . . 1 . . . . . . . . . .17820. . . . . . . . . . . . . Plug, By-Pass, Inlet

5B. . . . . . . 1 . . . . . . . . . .17820-01 . . . . . . . . . . Plug, By-Pass, Outlet (White)

6 . . . . . . . 4 . . . . . . . . . . 18661 . . . . . . . . . . . . .O-Ring, -218

7 . . . . . . . 2 . . . . . . . . . . 18662. . . . . . . . . . . . . Retaining Ring

8 . . . . . . . 2 . . . . . . . . . . 18660 . . . . . . . . . . . . .O-Ring

9 . . . . . . . 2 . . . . . . . . . . 13305 . . . . . . . . . . . . .O-Ring, -119

10 . . . . . . 2 . . . . . . . . . . 13255. . . . . . . . . . . . . Clip, Mounting

11 . . . . . . 2 . . . . . . . . . . 13314. . . . . . . . . . . . . Screw, Hex Washer Head, 8-18 x 5/8

12A. . . . . 1 . . . . . . . . . . 18706. . . . . . . . . . . . . Yoke, Plastic, 1″ NPT

18706-02 . . . . . . . . . . Yoke, Plastic 3/4″

12B. . . . . . 1. . . . . . . . . . 13708 . . . . . . . . . . . . . Yoke, 3/4″

1. . . . . . . . . . 13708NP . . . . . . . . . . Yoke, 3/4″ Nickel Plated

1. . . . . . . . . . 13398. . . . . . . . . . . . . Yoke, 1″

1. . . . . . . . . . 13398NP . . . . . . . . . . Yoke, 1″ Nickel Plated

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Meter Assembly

Page 27

Item No. No. Req’d Part No. Description

1 . . . . . . . . . . 4 . . . . . . . 12473 . . . . . . . . . . . . Screw - Meter Cover Assembly

2A. . . . . . . . . 1 . . . . . . . 14038. . . . . . . . . . . . .Meter Cover Assembly - Standard

2B . . . . . . . . . 1 . . . . . . . 15659. . . . . . . . . . . . .Meter Cover Assembly - Extended

Range, Rt. Angle

3. . . . . . . . . . . 1 . . . . . . . 13847 . . . . . . . . . . . .O-Ring - Meter Cover Assembly

4. . . . . . . . . . . 1 . . . . . . . 13509 . . . . . . . . . . . .Impeller

5. . . . . . . . . . . 4 . . . . . . . 13314 . . . . . . . . . . . .Screw - Adapter Clip

6. . . . . . . . . . . 4 . . . . . . . 13255 . . . . . . . . . . . .Adapter Clip

7. . . . . . . . . . . 1 . . . . . . . 13821 . . . . . . . . . . . .Meter Body

8. . . . . . . . . . . 4 . . . . . . . 13305 . . . . . . . . . . . .O-Ring - Meter Body

9. . . . . . . . . . . 1 . . . . . . . 14613 . . . . . . . . . . . .Flow Straightener

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Bypass Valve Assembly, Brass

Page 28

Item No. No. Req’d Part No. Description

1 . . . . . . . . 1 . . . . . . . . . .19723 . . . . . . . . . . . By-Pass Valve Body, Plastic

1 . . . . . . . . 1 . . . . . . . . . .17290 . . . . . . . . . . . By-Pass Valve Body, 3/4″

1 . . . . . . . . . .17290NP. . . . . . . . . By-Pass Valve Body, 3/4″ Nickel Plate

1 . . . . . . . . . .13399 . . . . . . . . . . . By-Pass Valve Body, 1″

1 . . . . . . . . . .13399NP. . . . . . . . . By-Pass Valve Body, 1″ , Nickel Plate

2 . . . . . . . . 1 . . . . . . . . . .11726 . . . . . . . . . . . Seal, By-Pass

3 . . . . . . . . 1 . . . . . . . . . .11972 . . . . . . . . . . . Plug, By-Pass

4 . . . . . . . . 1 . . . . . . . . . .11978. . . . . . . . . . . Side Cover

5 . . . . . . . . 1 . . . . . . . . . .13604-01 . . . . . . . . Label

6 . . . . . . . . 8 . . . . . . . . . .15727. . . . . . . . . . . Screw

7 . . . . . . . . 1 . . . . . . . . . .11986. . . . . . . . . . . Side Cover

8 . . . . . . . . 1 . . . . . . . . . .11979. . . . . . . . . . . Lever, By-Pass

9 . . . . . . . . 1 . . . . . . . . . .11989. . . . . . . . . . . Screw, Hex Head, 1/4-14

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Service Assembly Parts List

Part No. Description

60102-00 . . . . . . . Piston - Softener

60102-10 . . . . . . . Piston - Filter

60102-20 . . . . . . . Piston - Low Water

60125 . . . . . . . . . . Seal Kit

60084-XX . . . . . . . Injector

60032 . . . . . . . . . . Brine Valve

60514 . . . . . . . . . . Brine Cam, 3-18

60514-01 . . . . . . . Brine Cam, 6-36

60514-02 . . . . . . . Brine Cam, Minutes

60510 . . . . . . . . . . Coupling with Clip & Screws

60040 . . . . . . . . . . Bypass, Brass 3/4″ NPT

60041 . . . . . . . . . . Bypass, Brass 1″ NPT

60049 . . . . . . . . . . Bypass, Brass, Plastic

60086 . . . . . . . . . . Meter, Std.

60087 . . . . . . . . . . Meter, Ext.

60136-5600 . . . . . Service Kit, Meter

60135-5600 . . . . . Service Kit, Clock

14860 . . . . . . . . . . Skipper Wheel 7 Day

14381 . . . . . . . . . . Skipper Wheel 12 Day

60405-10 . . . . . . . Meter Program Wheel, Std.

60405-20 . . . . . . . Meter Program Wheel, Ext.

Page 29

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Troubleshooting

Page 30

PROBLEM CAUSE

1. Softener Fails to Regenerate A. Electrical Service To Unit Has Been

Interrupted.

CORRECTION

A. Assure Permanent Electrical Service.

(Check Fuse, Plug, Pull chain or Switch)

B. Timer is Defective

C. Power Failure

2. Softener delivers Hard water A. Bypass Valve is open.

B. No Salt in Brine Tank.

B. Replace Timer.

C. Reset Time of Day.

A. Close Bypass Valve.

B. Add Salt to Brine Tank and maintain

Salt Level above water level.

3. Unit Uses too much salt.

4. Loss of Water Pressure

C. Injectors or Screen Plugged.

D. Insufficient Water Flowing Into Brine

Tank.

E. Hot Water Tank Hardness.

F. Leak At Distributor Tube.

G. Internal Valve Leak.

A. Improper Salt Setting.

B. Excessive Water in Brine Tank.

A. Iron Buildup in Line to Water

Conditioner.

C. Clean Injector Screen.

D. Check Brine Tank Fill Time and Clean

Brine Line Flow Control if Plugged.

E. Repeat Flushings of the Hot Water Tank is

Required.

F. Make Sure Distributor Tube is Not

Cracked. Check “O” Ring and Tube Pilot.

G. Replace Seals and Spacers and/or Piston.

A. Check Salt Usage and Salt Setting.

B. See Problem No. 7.

A. Clean Line to Water Conditioner

5. Loss of Mineral Through Drain

Line.

A. Air in Water System.

6. Iron in Conditioned Water.

B. Iron Buildup in Water Conditioner B. Clean Control and Add Mineral Cleaner

to Mineral Bed. Increase Frequency of

Regeneration.

C. Inlet of Control Plugged Due to Foreign

Material Broken Loose From Pipes by

Recent Work Done on Plumbing System.

C. Remove Piston and Clean Control.

A. Fouled Mineral Bed.

A. Assure that Well System has Proper Air

Eliminator Control. Check for Dry Well

Condition.

A. Check Backwash, Brine Draw and Brine

Tank Fill. Increase Frequency of

Regeneration. Increase Backwash Time.

7. Excessive Water in Brine Tank. A. Plugged Drain Line Flow Control.

8. Salt water in service line A. Plugged Injector System.

B. Timer Not Cycling.

C. Foreign Material in Brine Valve

D. Foreign Material in Brine Line Flow

Control.

A. Clean Flow Control.

A. Clean Injector and Screen.

B. Replace timer.

C. Replace Brine Valve Seat and Clean Valve.

D. Clean Brine Line Flow Control.

9. Softener Fails to Draw brine. A. Drain Line Flow Control is Plugged.

B. Injector is Plugged.

C. Injector Screen Plugged.

D. Line Pressure is too Low.

E. Internal Control Leak.

A. Clean Drain Line Flow Control.

B. Clean Injector.

C. Clean Screen.

D. Increase Line Pressure to 20 P.S.I.

E. Change Seals, Spacers and Piston Assembly.

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Troubleshooting cont.

Page 31

PROBLEM CAUSE

10. Control Cycles Continuously. A. Broken or Shortened Switch.

CORRECTION

A. Determine if Switch or Timer is Faulty and

replace it, or Replace Complete Power Head.

11. Drain Flows Continuously. A. Internal Control Leak.

B. Foreign Material in Control.

A. Replace seals and/or piston assembly.

B. Remove piston assembly and inspect

bore. Remove Foreign Material and Check

Control in Various Regeneration Positions.

C. Replace Seals and/or Piston Assembly. C. Control valve jammed in brine or backwash position

D. Timer motor stopped or jammed. D. Replace timer.

GENERAL SERVICE HINTS FOR METER CONTROL

Problem: Softener Delivers Hard Water

Cause could be that . . . Reserve capacity has been exceeded.

Correction: Check salt dosage requirements and reset program wheel to provide additional reserve.

Cause could be that . . . Program wheel is not rotating with meter output.

Correction: Pull cable out of meter cover and rotate manually. Program wheel must move without binding and clutch must give positive “clicks” when program wheel strikes regeneration stop. If it does not, replace timer.

Cause could be that . . . Meter is not measuring flow.

Correction: Check output by observing rotation of small gear on front of timer (Note - program wheel must not be against regeneration stop for this check).

Each tooth to tooth is approximately 30 gallons. If not performing properly, replace meter.

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Service Instructions

A. TO REMOVE TIME BRINE VALVE, INJECTORS, AND SCREEN

1. Unplug electrical cord from outlet.

2. Turn off water supply to conditioner:

a. If the conditioner installation has a “three valve” by-pass system, first open the

valve in the by pass line, then close the valves at the conditioner inlet and outlet.

b. If the conditioner has an integral by-pass valve, put it in the by-pass position.

c. If there is only a shut-off valve near the conditioner inlet, close it.

3. Relieve water pressure in the conditioner by putting the control in the backwash position momentarily. Return the control to the service position.

4. Disconnect brine tube and drain line connections at the injector body.

5. Remove the two injector body mounting screws. The injector and brine module can now be removed from the control valve. Remove and discard valve body Orings

6. To Replace Brine Valve

1. Pull brine valve from injector body, also remove & discard O-ring at bottom of

brine

0. Apply silicone lubricant to new O-ring and reinstall at bottom of brine valve hole.

0. Apply silicone lubricant to O- ring on new valve assembly and press into brine valve hole, shoulder on bushing should be flush with injector body.

7. To replace injectors and screen.

1. Remove injector cap and screen, discard O-ring. Unscrew injector nozzle and throat from injector body.

0. Screw in new injector throat and nozzle, be sure they are seated tightly. Install a screen.

0. Apply silicone lubricant to new “O” ring and install around oval extension on cap.

8. Apply silicone lubricant to three new O-rings and install over three bosses on injector body.

9. Insert screws with washers thru injector cap and injector. Place this assembly thru hole in timer housing and into mating holes in the valve body. Tighten screws. (Be sure to reinstall brass spacers with injector on model 4600 valve.)

10. Reconnect brine tube and drain line.

11. Return by-pass or inlef valving to normal service position. Water pressure should now be applied to the conditioner, and any by-pass line shut off.

12. Check for leaks at all seal areas. Check drain seal with the control in the backwash position.

13. Plug electrical cord into outlet.

14. Set time of day and cycle the control valve manually to assure proper function. Make sure the control valve is returned to the service position.

15. Make sure there is enough brine in the brine tank.

16. Rotate program wheel counter-clockwise until it stops at regeneration position

17. Start regeneration cycle manually if water is hard.

Page 32

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Service Instructions Cont.

Page 33

B. TO REPLACE TIMER

1. Unplug electrical cord from outlet.

2. Turn off water supply to conditioner:

a. If the conditioner installation has a “three valve” by-pass system, first open the valve in the bypass line, then close the valves at the conditioner inlet and outlet.

b. If the conditioner has an integral by-pass valve, put it in the by-pass position.

c. If there is only a shut-off valve near the conditioner inlet, close it.

3. Relieve water pressure in the conditioner by putting the control in the backwash position momentarily. Return the control to the service position.

4. Pull cable out of meter cover. Remove the control valve back cover.

5. Remove screw and washer at drive yoke. Remove timer mounting screws. The entire timer assembly will now lift off easily.

6. Put new timer on top of valve. Be sure drive pin on main gear engages slot in drive yoke (rotate control knob if necessary).

7. Replace timer mounting screws. Replace screw and washer at drive yoke.

8. Return by-pass or inlet valving to normal service position. Water pressure should now be applied to the conditioner, and any by-pass line shut off.

9. Plug electrical cord into outlet.

10. Set time of day, program wheel, and salt usage. Cycle the control valve manually to assure proper function. Make sure the control valve is returned to the service position.

11. Replace the control valve back cover. Be sure grommet at cable hole is in place.

12. Make sure there is enough brine in the brine tank.

13. Rotate program wheel counter-clockwise until it stops at regeneration position.

14. Start regeneration cycle manually if water is hard.

15. Plug cable into meter cover, rotate cable to align drive flat if necessary.

C. TO REPLACE PISTON ASSEMBLY

1. Unplug electrical cord from outlet.

2. Turn off water supply to conditioner:

a. If the conditioner installation has a “three valve” by-pass system, first open the valve in the bypass line, then close the valves at the conditioner inlet and outlet.

b. If the conditioner has an integral by-pass valve, put it in the by-pass position.

c. If there is only a shut-off valve near the conditioner inlet, close it.

3. Relieve water pressure in the conditioner by putting the control in the backwash position momentarily. Return the control to the service position.

4. Pull cable out of meter cover. Remove the control valve back cover.

5. Remove screw and washer at drive yoke. Remove timer mounting screws. The entire timer assembly will now lift off easily. Remove end plug retainer plate.

6. Pull upward on end of piston yoke until assembly is out of valve.

7. Inspect the inside of the valve to make sure that all spacers and seals are in place, and that there is no foreign matter that would interfere with the valve operation.

8. Take new piston assembly as furnished and push piston into valve by means of the end plug. Twist yoke carefully in a clockwise direction to properly align it with drive gear. Replace end plug retainer plate.

9. Place timer on top of valve. Be sure drive pin on main gear engages slot in drive yoke

(rotate control knob if necessary).

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Service Instructions Cont.

Page 34

C. TO REPLACE PISTON ASSEMBLY cont.

10. Replace timer mounting screws. Replace screw and washer at drive yoke.

11. Return by-pass or inlet valving to normal service position. Water pressure should now be applied to the conditioner, and any by-pass line shut off.

12. Plug electrical cord into outlet.

13. Set time of day. Cycle the control valve manually to assure proper function. Make sure the control valve is returned to the service position.

14. Replace the control valve back cover. Be sure grommet at cable hole is in place.

15. Make sure there is enough brine in the brine tank.

16. Rotate program wheel counter-clockwise until it stops at regeneration position.

17. Start regeneration cycle manually if water is hard.

18. Plug cable into meter cover. Rotate cable to align drive flat if necessary.

D. TO REPLACE SEALS AND SPACERS

1. Unplug electrical cord from outlet.

2. Turn off water supply to conditioner:

a. If the conditioner installation has a “three valve” by-pass system, first open the valve in the bypass line, then close the valves at the conditioner inlet and outlet.

b. If the conditioner has an integral by-pass valve, put it in the by-pass position.

c. If there as only a shut-off valve near the conditioner inlet, close it.

3. Relieve water pressure in the conditioner by putting the control in the backwash position momentarily. Return the control to the service position.

4. Pull cable out of meter cover. Remove the control valve back cover.

5. Remove screw and washer at drive yoke. Remove timer mounting screws. The entire timer assembly will now lift off easily. Remove end plug retainer plate.

6. Pull upward on end of piston rod yoke until assembly is out of valve. Remove and replace seats and spacers with fingers.

E. TO REPLACE METER

1. Unplug electrical cord from outlet.

2. Turn off water supply to conditioner:

a. If the conditioner installation has a “three valve” by-pass system, first open the valve in the bypass line, then close the valves at the conditioner inlet and outlet.

b. If the conditioner has an integral by-pass valve, put it in the by-pass position.

c. If there is only a shut-off valve near the conditioner inlet, close it.

3. Relieve water pressure in the conditioner by putting the control in the backwash position momentarily. Return the control to the service position.

4. Pull cable out of meter cover.

5. Remove two screws and clips at by-pass valve or yoke. Pull resin tank away from plumbing Connections.

6. Remove two screws and clips at control valve. Pull meter module out of control valve.

7. Apply silicone lubricant to four new O-rings and assemble to four ports on new meter module.

8. Assemble meter to control valve. Note, meter portion of module must be assembled at valve outlet.

9. Attach two clips and screws at control valve. Be sure clip legs are firmly engaged with lugs.

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Service Instructions Cont.

E. TO REPLACE METER cont.

10. Push resin tank back to the plumbing connections and engage meter ports with bypass valve or yoke.

11. Attach two clips and screws at by-pass valve or yoke. Be sure clip legs are firmly engaged with lugs.

12. Return by-pass or inlet valving to normal service position. Water pressure should now be applied to the conditioner, and any by-pass line shut off.

13. Check for leaks at all seal areas.

14. Plug electrical cord into outlet.

15. Set time of day. Make sure the control valve is in the service position.

16. Rotate program wheel counter-clockwise until it stops at regeneration position.

17. Start regeneration cycle manually if water is hard.

18. Plug cable into meter cover. Rotate cable to align drive flat if necessary.

F. TO REPLACE METER COVER AND/OR IMPELLER

1. Unplug electrical cord from outlet.

2. Turn off water supply to conditioner:

a. If the conditioner installation has a “three valve” by-pass system, first open the valve in the bypass line, then close the valves at the conditioner inlet and outlet.

b. If the conditioner has an integral by-pass valve, put it in the by-pass position.

c. If there is only a shut-off valve near the conditioner inlet, close it.

3. Relieve water pressure in the conditioner by putting the control in the backwash position momentarily. Return the control to the service position.

4. Pull cable out of meter cover.

5. Remove four screws on cover

6. Lift cover off of meter module, discard O-ring.

7. Remove and inspect impeller for gear or spindle damage, replace if necessary.

8. Apply silicone lubricant to new O-ring and assemble to the smallest diameter on meter cover.

9. Assemble cover to meter module. Be sure impeller spindle enters freely into cover.

Press firmly on cover and rotate if necessary to assist in assembly.

10. Replace four screws and tighten.

11. Return by-pass or inlet valving to normal service position. Water pressure should now be applied to the conditioner, and any by-pass line shut off.

12. Check for leaks at all seal areas.

13. Plug electrical cord into outlet.

14. Set time of day. Make sure the control valve is in the service position.

15. Rotate program wheel counter-clockwise until it stops at regeneration position.

16. Start regeneration cycle manually if water is hard.

17. Plug cable into meter cover. Rotate cable to align drive flat if necessary.

Page 35

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Warranty

10 YEAR WARRANTY

FOR RESIDENTIAL APPLICATIONS

Congratulations on the purchase of your PURE TECH Water System. PURE

WATER TREATMENT, INC. warrants its products to be free from defects in material and workmanship according to the following terms and conditions:

I.

What is Covered?

The PURE TECH 2200 series.

10 YEARS ON PARTS

II. The PURE TECH 1000 R.O. System

A.

10 YEARS PARTS

5 YEARS ON THE REVERSE OSMOSIS

MEMBRANE

B.

10

3 YEARS REVERSE OSMOSIS

MEMEBRANE

______________________________________________________________________________________

Who is Covered?

This product warranty is transferable to a subsequent owner. The only requirement is that the system must remain at the site of original installation.

______________________________________________________________________________________

Extension of Warranty to a Subsequent Installation

The ORIGINAL OWNER may move the system to another location. The influent water quality at the subsequent location MUST, however, be within your system’s operating specifications. Please contact a local authorized PURE

TECH dealer prior to installation at another location.

______________________________________________________________________________________

Registration and Service

To place your system under warranty, your authorized

PURE TECH dealer should complete the owner’s registration form and return one copy to: PURE WATER TREAT-

MENT, INC., P.O. Box 730486, Ormond Bch, FL 32173-

0486, within 30 days of the installation date. For service under this warranty, you should contact the dealer. Retain a copy of this warranty for reference if service is necessary.

Limits on this Warranty

Your system must be sold to you by an authorized PURE

TECH dealer in order to receive coverage under this warranty. Additionally, this warranty does not cover products installed for commercial, industrial, institutional or multifamily applications.

The design of the overall treatment system and performance of your system is related to the chemistry of the water being treated; therefore, This warranty is limited to the equipment manufactured and distributed by PURE WATER TREATMENT,

INC.

This Warranty does not include damage to your system due to:

Abuse, misuse or neglect

Excessive pressure (over 100 psi for a PURE TECH 1000

R.O. system, or 125 psi for all other PURE TECH systems)

Excessive water temperature (over 100° for a PURE TECH

1000 R.O. system, or 120° for all other PURE TECH systems)

Freezing, alterations or misapplication

A change in the influent water characteristics

Your equipment must be installed and operated in accordance with your owners manual’s recommendations and applicable state and local codes.

______________________________________________________________________________________

No Other Warranties

There is no other express warranty. Implied warranties including any warranty of merchantability or fitness for a particular purpose, are limited to the duration of this warranty and are excluded to the extent permitted by law. There are no warranties other than those contained herein. In no event shall the company be liable for indirect, special or consequential damages in connection with the use of the system.

______________________________________________________________________________________

Modification of the Warranty

PURE WATER TREATMENT, INC. does not authorize any other person to assume for PURE WATER

TREATMENT, INC. any other liability in connection with this product.

The dealer has no authority to make any representations on behalf of PURE WATER TREATMENT, INC. or to modify the terms of this warranty in any way.

Page 36

P.O. Box 730486

Ormond Beach, FL 32173-0486

OFFICE 1-888-989-PURE · FAX 1-877-219-PURE

“Our Reputation Is Worth More Than Money”

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

Notes

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

________________________________________________________________________

Page 37

Tech Support: 1-888-989-7873 PURE WATER TREATMENT, INC.

advertisement

Related manuals

Download PDF

advertisement