Asia Pacific Microsystems RU5AWBFXU BLUETOOTHUSB DONGLE User Manual

Add to my manuals
60 Pages

advertisement

Asia Pacific Microsystems RU5AWBFXU BLUETOOTHUSB DONGLE User Manual | Manualzz

IVT BlueSoleil™

User Manual

Version: 1.4

This document describes how to use IVT BlueSoleil ™ .

FCC DoC Labeling

Class 2 Bluetooth Pen Drive

Tested to Comply

With FCC Standard

FOR HOME OR OFFICE USE

FEDERAL COMMUNICATIONS COMMISSION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.

The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter

This EUT is compliance with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C

Prohibition of co-location

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter

IVT BlueSoleil™ User Manual

Contents

1 BlueSoleil™ Introduction............................................................................ 1

1.1

Profiles ....................................................................................................1

1.2

New features in BlueSoleil 1.4 .....................................................................2

1.3

Features in BlueSoleil 1.2 ...........................................................................2

2 BlueSoleil™ Basic Operations ..................................................................... 4

2.1

Start BlueSoleil™ ......................................................................................4

2.2

Exit BlueSoleil™ ........................................................................................4

2.3

BlueSoleil™ Main Window ...........................................................................5

2.4

Service Window.........................................................................................8

2.5

What You Need To Do Before Build A Connection ......................................... 10

2.6

Start Or Stop A Bluetooth Service Connection.............................................. 14

3 Bluetooth Security.................................................................................... 16

3.1

Introduction ........................................................................................... 16

3.2

BlueSoleil Security Configuration ............................................................... 17

4 Personal Area Networking........................................................................ 22

4.1

Introduction ........................................................................................... 22

4.2

Communication Between Two Computers.................................................... 23

4.3

Access LAN Through PAN-NAP ................................................................... 29

4.4

Access LAN Through IVT BlueSoleil™.......................................................... 33

4.5

Access Internet through IVT BlueSoleil™..................................................... 35

4.6

PAN Configuration ................................................................................... 36

5 Dial-Up Networking.................................................................................. 38

5.1

Introduction ........................................................................................... 38

5.2

Connect to a Dial-up Gateway from a Computer........................................... 38

5.3

Settings for Dial-up Networking Profile (client side) in Windows98/Me ............. 41

6 Bluetooth Serial Port ................................................................................ 46

6.1

Introduction ........................................................................................... 46

6.2

Connect Two Computers........................................................................... 46

6.3

Use SPP to Print a Document..................................................................... 48

6.4

Use a cellphone to control a computer ........................................................ 48

6.5

SPP Configuration.................................................................................... 50

7 Bluetooth File Transfer............................................................................. 52

7.1

Introduction ........................................................................................... 52

7.2

Transfer files to/from a Computer .............................................................. 52

7.3

FTP Configuration .................................................................................... 55

8 LAN Access............................................................................................... 56

8.1

Introduction ........................................................................................... 56

8.2

Access a Local Area Network (LAN) ............................................................ 56

8.3

Access a LAN via a LAN Access Point .......................................................... 60

8.4

Settings for LAN Access Profile (client side) in Windows98/Me........................ 61

8.5

Usage of LAN Access Profile (server side) in Windows98/Me........................... 65

9 Object Push.............................................................................................. 70

9.1

Introduction ........................................................................................... 70

9.2

Transfer Objects from a Computer to a Bluetooth Cellular Phone .................... 70

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

2

IVT BlueSoleil™ User Manual

9.3

Transfer Objects from a Bluetooth Cellular Phone to a Computer .................... 74

9.4

Transfer Objects between Two Computers................................................... 75

9.5

Configure OPP Service.............................................................................. 76

9.6

Using OPP in Microsoft Outlook .................................................................. 77

10 Synchronization..................................................................................... 80

10.1

Introduction......................................................................................... 80

10.2

Exchange PIM Data with a Cellular Phone ................................................. 80

10.3

Set up SYNC Connection between Two Computers ..................................... 81

10.4

Synchronization Configuration ................................................................ 83

10.5

Using Synchronization in Outlook ............................................................ 84

11 Hardcopy Cable Replacement ................................................................ 87

11.1

Introduction......................................................................................... 87

11.2

Print a Document Using a Bluetooth Printer .............................................. 87

12 Human Interface Device ........................................................................ 89

12.1

Introduction......................................................................................... 89

12.2

Connect a Computer to a Bluetooth Mouse ............................................... 89

12.3

Connect a Computer to a Bluetooth Keyboard ........................................... 91

13 FAX........................................................................................................ 94

13.1

Introduction......................................................................................... 94

13.2

Connect to a FAX Gateway from a Computer ............................................ 94

13.3

Using FAX software on a bluetooth computer ............................................ 94

14 Headset ................................................................................................. 96

14.1

Introduction......................................................................................... 96

14.2

Create an audio connection between computer and Headset ....................... 96

14.3

Using Headset Profile in BlueSoleil........................................................... 98

15 Advanced Audio Distribution ............................................................... 100

15.1

Introduction....................................................................................... 100

15.2

Play music between computer and AV Headphone wirelessly ..................... 100

15.3

Play music between two computers wirelessly......................................... 103

16 Basic Imaging ..................................................................................... 107

16.1

Introduction....................................................................................... 107

16.2

Push an image from a digital still camera. .............................................. 107

16.3

Control a digital still camera remotely.................................................... 108

17 Connection Shortcut ............................................................................ 110

17.1

Introduction....................................................................................... 110

17.2

How to use Connection Shortcut ........................................................... 110

18 Bluetooth Glossary .............................................................................. 113

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

3

IVT BlueSoleil™ User Manual

1 BlueSoleil ™ Introduction

BlueSoleil ™ is a Windows-based Bluetooth Wireless software suite from IVT

Corporation. It is fully compliant to the latest Bluetooth SIG specifications.

BlueSoleil ™ incorporates Bluetooth and computer technologies to enable users to wirelessly access computing devices, form networks, and exchange information.

1.1 Profiles

BlueSoleil ™ V1.4 includes ten Bluetooth profiles. The following table indicates which of these profiles is available for client and server devices.

Profile Description Client Server

PAN Personal Area Networking

HID

HCRP

Human Interface Device

Hardcopy Cable Replacement

SYNC Synchronization

AV Audio Source

Audio Sink

√ √

BlueSoleil ™ supports more than ten Bluetooth chip-sets and HCI interfaces including USB, UART, PCMCIA and Compact Flash.

IVT BlueSoleil ™ supports:

♦ Windows 2000/XP

♦ Windows 98SE/Me

This manual describes how to use BlueSoleil ™ :

♦ How to start and exit BlueSoleil ™ .

♦ How to navigate the Main Window and Service Window.

♦ How to use the Bluetooth profiles.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

1

IVT BlueSoleil™ User Manual

1.2 New features in BlueSoleil 1.4

BlueSoleil version 1.4 is ready now with even more exciting new features, multimedia profiles are added into BlueSoleil.

They include:

♦ Headset

With this feature, users can use Bluetooth Headset to listen to music, to record sound or to chat with others. Headset increases the user’s mobility.

♦ Audio/Video

With this feature, users can listen to stereo music with any media player wirelessly between Bluetooth enabled computers or Bluetooth enabled computer and Bluetooth Stereo headphone.

♦ Basic Image

With this feature, users can push an image from a digital still camera to a computer, or control a digital still camera remotely from a computer.

1.3 Features in BlueSoleil 1.2

BlueSoleil version 1.2.0 is ready with exciting new features, aiming at making

Bluetooth more easy to use for end user. Less steps is required to setup wireless connections. User can even do not care what is Bluetooth. Anyway, Bluetooth is just a kind of connecting method. So, please just have fun from all these new functions.

They include:

♦ Seamless Integration with Windows

This is an important improvement to make it more easy to use Bluetooth.

Generally, users do not care about what is Bluetooth and how can they connect to a Bluetooth device. From users' point of view, they just want to print a document, open a serial port, dial-up to Internet and send a FAX etc. To make this, BlueSoleil automatically setup Bluetooth connections for users. There is no need to setup connection before using Bluetooth anymore.

♦ Integration with MS Outlook for Object Push and Synchronization

With this feature, contact cards and email messages can be sent or synchronized from Outlook directly via Bluetooth. Received cards and other information items will be imported to Outlook automatically.

♦ Shortcut on Windows Desktop

Windows shortcut is introduced here to let user to be able to setup Bluetooth connection when they want by just double- clicking them. It makes Bluetooth connection extremely simple.

♦ Security 2

With this feature, users can manage local Bluetooth services in a flexible way.

Authentication, encryption and authorization can be configured based on every service. Users can set which remote device can access local services and which not.

♦ FAX

FAX enable users to send a FAX from PC side via Bluetooth cellular phone or

Bluetooth FAX machine wirelessly.

♦ Network Address Translation, Network Access Point, and DHCP server in PAN

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

2

IVT BlueSoleil™ User Manual

With these functions, users can setup ad-hoc Personal Area Network quickly and share the Internet accessing among computer.

♦ More Bluetooth Serial Ports

More Bluetooth Serial Ports are supported, with 4 Bluetooth Serial Ports for out-going connections and 2 Bluetooth Serial Ports for incoming connections.

♦ Mobile HID

With this feature, users can make cellular phones like Ericsson T39 or T68 to work like a mouse and keyboard. Users can remotely control their PC to show

Power Point etc.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

3

IVT BlueSoleil™ User Manual

2 BlueSoleil™ Basic Operations

After installing BlueSoleil™, there are two ways to start the program:

1. A BlueSoleil™ shortcut icon on the Windows desktop.

2. An IVT BlueSoleil ™ program group entry in the Windows’ Start | Programs menu.

Double-click the BlueSoleil ™ shortcut icon on the desktop or click the BlueSoleil™ menu item on the Start | Programs | IVT BlueSoleil ™ menu to start the

BlueSoleil™ software.

The BlueSoleil™ icon will be displayed at the bottom right corner of the

Windows desktop (Figure 2.1).

Figure 2.1: BlueSoleil™ icon

The BlueSoleil ™ Main Window pops up as shown in Figure 2.2.

2.2 Exit ™

To exit BlueSoleil ™ , right-click the BlueSoleil™ icon at the bottom right corner of the

Windows task bar and select Exit on the pop-up menu.

Note: Selecting the Close button at the top right corner of the BlueSoleil™ window only hides the BlueSoleil™ window.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

4

IVT BlueSoleil™ User Manual

2.3 BlueSoleil™ Main Window

The BlueSoleil™ Main Window displays all surrounding Bluetooth devices. From the BlueSoleil™ Main Window users can search for surrounding Bluetooth devices and can execute connect/ disconnect functions.

Remote Device Serivce Icon

Remote Device

Local Device Icon

Figure 2.2: BlueSoleil™ Main Window

The main elements in the BlueSoleil™ Main Window are:

♦ My Device Icon

♦ Remote Bluetooth Device Icons

♦ Bluetooth Service Icons

2.3.1 My Device Icon

This icon represents the client computer. It is called the ‘My Device icon’ or ‘center ball’ in this document.

Functions:

♦ Hover the mouse over the My Device icon to display the client Bluetooth device name and address.

♦ Double-click to start/ stop searching for surrounding Bluetooth devices.

♦ Drag scrollbar on the right of main window to find other Bluetooth devices if there are more than seven devices.

♦ Right-click to display the pop-up menu with related operations.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

5

IVT BlueSoleil™ User Manual

2.3.2 Remote Bluetooth Device Icons

The icons in the table below represent the remote Bluetooth devices.

Device Type Icon

Headset

Keyboard

LAN Access Point

Laptop

Mobile

Modem

Mouse

Personal Computer

PDA

Printer

Scanner

Unknown device

The following colors are used to indicate the status of the remote Bluetooth device:

♦ White (Idle)

This is the normal status of the device.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

6

IVT BlueSoleil™ User Manual

♦ Yellow (Selected)

The device has been selected by the user.

♦ Green (Connected)

The device has been connected.

Functions:

♦ Single-click to select.

♦ Double-click to get the services remote Bluetooth device supports.

♦ Right-click to display the pop-up menu with related operations.

2.3.3 Bluetooth Service Icons

The Bluetooth Service Icons represent the Bluetooth services supported by the remote device.

Bluetooth Service Icon

Personal Area Networking

Dial-up Networking

Serial Port

LAN Access

File Transfer

Information Synchronization

Object Push

Printer

Fax

Human Interface Device

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

7

IVT BlueSoleil™ User Manual

AV Headphone

Basic Image

Headset Audio Gateway

The following colors are used to indicate the status of the Bluetooth service:

♦ White (Idle)

This is the normal status.

♦ Pink (Available)

The Bluetooth service is available for the selected device.

♦ Yellow (Selected)

The service icon has been selected by the user.

♦ Green (Connected)

The service is connected.

Functions:

♦ Hover the mouse over the icon to display the service name.

♦ Single-click to select the service.

♦ Double-click to connect.

♦ Click to display the pop-up menu with related operations.

Figure 2.3: Bluetooth PAN Service Icon

Select menu View | Service Window and the Service Window appears.

This window displays the Bluetooth services the ‘my Bluetooth device’ provides to remote Bluetooth devices. These services are called ‘my Bluetooth services’.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

8

IVT BlueSoleil™ User Manual

Figure 2.4: BlueSoleil™ Service Window

Main Elements:

♦ My Service Icons

2.4.1 My Service Icons

These icons represent ‘my Bluetooth services’.

My Bluetooth Service Icon

Personal Area Networking

Serial Port

LAN Access

Object Push

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

9

IVT BlueSoleil™ User Manual

File Transfer

Information Synchronization

AV Headphone

Basic Image

Headset AG

The following colors indicate the status of the Bluetooth service:

♦ White (Idle)

Normal status.

♦ Pink (Started)

My Bluetooth service is started.

♦ Green (Connected)

A remote device has connected to my Bluetooth service.

2.4.2 Start/Stop a Bluetooth Service

Select a service icon in service window, and double-click to start/stop a service or select right popup menu to send command.

2.4.3 View the Property of a Service

Right-click to display the pop-up menu with related operations in service window.

2.5 What You Need To Do Before Build A Connection

3. Inquiring Bluetooth Devices in the vicinity

4.

Pairing your desktop or laptop with the associated device

2.5.1

Inquiring Bluetooth Devices

Method 1: Enquire Device

To start to set up a Bluetooth connection, you have to find the remote device you want to connect first. You can choose one of the following methods to find the remote device.

You may double click My Bluetooth Device icon or from MY Bluetooth Menu

-> Bluetooth Device Inquiry (Figure 2.5) to find other Bluetooth devices in range. Bluetooth devices within the radio range will be added to the orbit. The inquiry procedure will search up to 7 devices each time. After it finds the devices or it has been 25 seconds since the beginning of the inquiry, it will continue to refresh

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

10

IVT BlueSoleil™ User Manual the names of the found devices. Double clicking the local device or double clicking one of the remote devices (to start to search profiles it supports) will stop the inquiry procedure.

Figure 2.5 Inquiry Menu

Method 2: Add Device from History List

If there are more than 7 devices to find within the radio range, you can add the device you have used to the orbit from the history device list. Click Tools Menu and select Add Device from History.

The History dialog box will be pop-up

(Figure 2.6).

Figure 2.6 History Dialog

Select the device from the list and click Add , the selected device will be added to the end of the orbit. The shortcut key to open the History dialog box is Ctrl+H.

Method 3: Add a New Device by Inputting Device Address

If you are going to connect a device that you have never used, which is not in the history list and which you cannot find, you can add it directly by inputting its

Bluetooth device address. Click Tools Menu and select Add New Device . The

Add Bluetooth Neighbor Device Manually dialog box pops up.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

11

IVT BlueSoleil™ User Manual

Figure 2.7 Add Bluetooth Neighbour Device Manually dialog

Input the device address and click OK , and then the device will be added to the end of the orbit. However, the device type will be unknown. The shortcut key to open

Add Bluetooth Neighbor Device Manually dialog box is Ctrl+N.

The remote devices found will be added to the orbit. Refer to the following window

(Figure 2.8).

Figure 2.8 Devices can be add into the main window

2.5.2 Pairing your desktop or laptop with a Bluetooth Device

Bluetooth passkey may be asked if security level of either side of the connection is set to High and they are not paired devices. You can initiate the pairing from your own desktop or laptop or accept a request for pairing from the other device. Pairing allows you to avoid entering access information each time a connection is setup.

Paired devices share a unique Link Key, which they exchange each time they connect.

Pairing Procedures

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

12

IVT BlueSoleil™ User Manual

Double click the remote Bluetooth device you want to connect and you will be asked to enter the Bluetooth Passkey. Please type the Bluetooth Passkey in the Passkey field (Figure 2.9).

Figure 2.9 Input Passkey

Meanwhile, there will be a Bluetooth Passkey dialog box prompted on the remote laptop or desktop equipped with the Bluetooth device to ask you to enter passkey.

The Bluetooth passkey should be the same between paired devices. If the pairing process succeeds, there will be a red check on the paired Bluetooth device icon

(Figure 2.10).

Figure 2.10 Device have been paired

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

13

IVT BlueSoleil™ User Manual

2.6 Start Or Stop A Bluetooth Service Connection

After you have finished the pairing process, it means that you have built the connection between the client side and remote side. You may start to use the

Bluetooth services the associated Bluetooth device provides.

You can refer to 4.2 Communication Between Two Computers as a more detailed example.

2.6.1 Search Bluetooth Service

You can double click the associated Bluetooth device icon or right-click on the icon and select Refresh Services to find the service it provides. After service searching finishes, the services the remote device supports and the corresponding service icons on the top of the main window will change to be pink color.

2.6.2 Start A Remote Bluetooth Service Connection

You may right-click on the connected Bluetooth device, select Connect and highlight the service you want to use (Figure 2.11).

Or

Double click the pink profile icon (the service icon) you want to connect on the top of the Main Window.

Figure 2.11 Connect to the remote service

Connection will be setup. After connection is OK, the remote device and the service icon will turn green.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

14

IVT BlueSoleil™ User Manual

Figure 2.12 The connection has been established

2.6.3 Stop A Bluetooth Service Connection

There are two ways to stop the service:

♦ Select a started service and right click the service. On the popup menu, select

Stop Service . The service icon turns white. The service is stopped.

♦ Select a started service. Select My Services menu and highlight Stop Service .

The service icon turns white. The service is stopped.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

15

IVT BlueSoleil™ User Manual

3.1 Introduction

Bluetooth introduces security features to protect users from unauthorized access of local data and encrypt data in the air. Three levels of security is defined in

Bluetooth:

♦ Low (no security): Local device will not initiate any security procedure.

♦ Medium (service-level enforced security): Local device does not initiate security procedures before user access local Bluetooth services. This mode allows different and flexible access policies for Bluetooth applications, especially running applications with different security requirements in parallel.

♦ High(device level enforced security): Local device initiates security procedures as long as the remote Bluetooth device set-up link, for example, browsing local services etc.

Following table shows the security when Bluetooth client device access another

Bluetooth device that provides services.

Server in

Security Low

Server in

Security Medium

Server in

Security High

Client in

Security

Low

No security.

Client in

Security

Medium

Client in

Security

High

No security.

High. Security is enforced at link level before setup connection.

Can browse services.

Accessing service depends on the settings of local services.

Can browse services.

Accessing service depends on the settings of local services.

High. Security is enforced at link level before setup connection.

High. Security is enforced at link level before setup connection.

High. Security is enforced at link level before setup connection.

High. Security is enforced at link level before setup connection.

When security is enforced at device level or a local service requires, an

Authentication procedure is required. Both of Bluetooth client and server side need enter a Bluetooth passkey to confirm the client user's identity.

To avoid entering Bluetooth passkey every time, two Bluetooth devices can be set up paring relationship, that is to save the relationship after Authentication. After

Authentication , the Bluetooth link can be encrypted if necessary.

Authorization is used in Security Medium (service-level enforced security), to set which devices can use the local service and which cannot. The following are some concept of bluetooth security:

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

16

IVT BlueSoleil™ User Manual

♦ Authentication

Authentication is used to verify identity; it requires a passkey or link key from the remote device. When an Authentication procedure is initiated by either local device or remote device, a dialog is shown to ask for entering Bluetooth

Passkey. Only when passkeys from both sides are identical, can authentication succeed.

♦ Authorization

Bluetooth authorization is the procedure to decide whether you are going to allow some other Bluetooth devices to use Bluetooth services on your Bluetooth devices. This procedure takes function in Bluetooth security Medium and applies to Bluetooth services only.

♦ Encryption

When a Bluetooth link is encrypted, data are encrypted into unreadable data using a secret key or password before they are sent in the air. Data are decrypted after they reach the remote device using the same key or password that was used to encrypt it.

♦ Pairing Devices

Pairing allows you to avoid entering access information each time a connection is setup. Paired devices share a unique Link Key, which they exchange each time they connect.

The BlueSoleil security configuration involves the policy setting of the local device's security, it comprises the following items:

♦ General Property Page

♦ Devices Property Page

♦ Services Property Page

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

17

IVT BlueSoleil™ User Manual

3.2.1 General Property Page

Figure 3.1: Security Configuration Dialog

Security Level

♦ Low

When Low is checked, normally other devices may access your device freely, which means that they don't need to input the Bluetooth passkey. However, if the other device set its own security level to High, you are also required to input the passkey.

♦ Medium

The medium level is service level security. You can assign access right for specified service to different devices. For more detail, to see Services Property

Page.

♦ High

When other devices connect to your device or your device connects with other devices, you are required to input a Bluetooth passkey. If your device has been paired with the other device before connecting, you can connect with the other device directly. (A link key has been created and stored for the paired relationship. Link key is used instead of Bluetooth passkey here.)

Bluetooth Passkey

♦ Set Default Passkey

If you check Set Default Passkey, you needn't input passkey manually.

BlueSoleil will use the passkey inputted in the edit box below to connect with other devices.

Data Encrypt

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

18

IVT BlueSoleil™ User Manual

♦ Enable Data Encryption

If the item is checked, the transmitted data will be encrypted into an unreadable format.

3.2.2 Devices Property Page

Figure 3.2: Devices Property Page when you establish connection with a paired device, you needn't input a passkey again. A link key has been created and stored for the paired relationship.

How to pair with another device

♦ Automatically

If a passkey is required before connection, devices will pair automatically the first time they connect (a passkey must be successfully exchanged).

♦ Manually

In the main window of BlueSoleil, right click a device, select Pair Device from the popup menu, and then input a same passkey on both side.

How to unpair with another device

Manually

1. Click Remove Pairing button in this page.

2. In the main window of BlueSoleil, right click a paired device, select Unpair from the popup menu.

Authorization for paired devices

Only when the Security Level is set as Medium in General Property Page, the

Authorization button is enabled. Select a device in Paired Devices list, then click

Authorization button to show an authorization dialog.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

19

IVT BlueSoleil™ User Manual

Figure 3.3: Authorization Dialog

The services shown in Service Name list are those need Authentication. Configure in Services Property Page. If a service name is checked, the device will be a trusted device for the service.

3.2.3 Services Property Page

Only when the Security Level is set as Medium in General Property Page, the property page is enabled.

Figure 3.4: Services Property Page

Authentication

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

20

IVT BlueSoleil™ User Manual

♦ Checked

If you check the Authentication box after a service name, when a not paired device access the service, a passkey is required.

♦ Not Checked

The security level of the service will be Low. Any device may access the service freely.

Encryption

If check Encryption after a service name, the transmitted data for the service will be encrypted into an unreadable format.

Authorization for services

Select a service which need Authentication, then the Authorization button is enabled. Click Authorization button to show an authorization dialog for the specified service.

Figure 3.5: Authorization for Services

Trusted Devices

The devices are trusted by the specified service. Click Add button to add devices into Trusted Devices list. Only a paired and trusted device can use the service freely.

♦ Trust all devices

Set all devices trusted.

♦ Prompt to user if the device is not a trusted device of this service

If a device attempting to access the service is not a trusted device, a prompt dialog will popup on the server side to inquire user if accepting the connection.

♦ Reject the device to use the service if it is not a trusted device of this service

If a device attempting to access the service is not a trusted device, the device will be rejected to established connection directly.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

21

IVT BlueSoleil™ User Manual

4 Personal Area Networking

4.1 Introduction

The Bluetooth Personal Area Networking (PAN) is a Bluetooth application, which enables devices to form an ad-hoc network or to access a remote network through a network access point.

The PAN application can be used in the following scenarios:

♦ Two or more computers (or PDAs) can be connected to form a Group Ad-hoc

Network (GN) and can visit each other using Windows Network Places or any application based on TCP/IP. (Figure 4.1)

Figure 4.1: Group Ad-hoc Network

♦ Two or more computers (or PDAs) can access a Local Area Network through a

Network Access Point (NAP) bridge. (Figure 4.2) After the computers or PDAs connect to the PAN-NAP, they become members of the LAN and can communicate with other computers in the LAN directly.

Figure 4.2: Access LAN through PAN-NAP

♦ Two or more computers (or PDAs) can access a Local Area Network through

BlueSoleil™. ( Figure 4.3

) After the PANUs connect to the BlueSoleil NAP, they become members of the LAN and can communicate with other computers in the

LAN directly.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

22

IVT BlueSoleil™ User Manual

Figure 4.3: Access LAN through BlueSoleil NAP

♦ Two or more computers (or PDAs) can access the Internet through BlueSoleil™.

(Figure 4.4) In this scenario, there are two network adapters for the BlueSoleil

NAP: the WAN adapter is connected to the Internet and the BT network adapter is used for Bluetooth connections from the PANUs. The BlueSoleil NAP acts as a

TCP/IP gateway, and the PANUs can access the Internet through the BlueSoleil

NAP.

Figure 4.4: Access Internet through BlueSoleil NAP

Each of these scenarios is now covered in more detail.

4.2 Communication Between Two Computers

This section outlines the steps involved in connecting two computers, Computer A and Computer B.

Computer A: Computer B:

A Bluetooth Device

IVT BlueSoleil™

A Bluetooth Device

IVT BlueSoleil™

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

23

IVT BlueSoleil™ User Manual

Step 1: Insert Bluetooth Devices in both computers and start BlueSoleil™ in both computers.

Step 2: Set device name of each computer to anything you want. Here they are named Computer A and Computer B.

♦ In the BlueSoleil™ Main Window of Computer A, click My

Bluetooth | Property… . Enter ‘Computer A’ in the device name field in the My Bluetooth Device window.

♦ Repeat for Computer B.

Step 3: Set the Security Level.

♦ Click My Bluetooth| Security, the Security Configuration panel pops up.

♦ On the Security Configuration panel, select High in Security

Level.

♦ Note: If you check the Fixed Passkey and input a Bluetooth passkey, this passkey will be used as the default passkey. The other computer will then have to provide the same passkey during the connection procedure if it wants to connect to this computer.

Figure 4.5: Security Configuration

Step 4: Start the PAN service on Computer A.

♦ In the BlueSoleil ™ Main Window, click View | Service Window.

♦ In the Service Window, right-click the Personal Area Networking icon. Choose Properties to configure my PAN service as Set up

Bluetooth Personal Area Network.

(Figure 4.6) If the item of

Enable DHCP Server is checked, a DHCP server will be started

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

24

IVT BlueSoleil™ User Manual on the GN side. (Notes: To use DHCP, the BT Network Adapter on the client side must be set to obtain an IP address automatically.

The IP address is in the form of 192.168.18.xxx.)

♦ Click Apply or OK button to save the configuration.

♦ Right-click the Personal Area Networking icon again, then choose

Start Service.

(Figure 4.7)

Figure 4.6: Set up Bluetooth Personal Area Network Configuration

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

25

IVT BlueSoleil™ User Manual

Figure 4.7: Start PAN Service on Computer A

Step 5: Search for Computer A on Computer B.

♦ Double-click the My Device Icon (center ball). The surrounding discovered Bluetooth devices appear.

♦ Check to see if Computer A appears. If it does not appear, double-click the My Device Icon again. Repeat the operation until you find Computer A.

Step 6: Find the PAN service on Computer A.

♦ Double-click the Computer A device icon on Computer B.

♦ Enter the Bluetooth passkey (if security is set to High on either side) to start the authenticating process. The Enter Bluetooth

Passkey window pops up on Computer A. Input any characters or numbers, e.g. “12”. The Enter Bluetooth Passkey window pops up on Computer B. Input exactly the same characters or numbers as you input for Computer A, e.g. “12”. (Figure 4.8)

♦ Once authentication is complete, the PAN service is found.

Figure 4.8: Input passkey

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

26

IVT BlueSoleil™ User Manual

Figure 4.9: PAN service is found

Step 7: Connect to Computer A.

♦ Right-click the PAN service icon; select Connect on the pop-up menu. (Figure 4.10)

♦ The connection is established successfully ( Figure 4.11).

Wait until the valid IP address is shown on the bottom right status bar on both Computer A and Computer B. If you enable the DHCP server on the server side, the IP address appears as

“192.168.18.xxx”. If not, the IP address appears as

“169.254.xxx.xxx”.

Figure 4.10: Connect to PAN Service

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

27

IVT BlueSoleil™ User Manual

Figure 4.11: Connection is established successfully.

Step 8: Computer A and Computer B are now connected. On Computer B, go to Windows | My Network Places to find Computer A and copy files. Figure 4.12 shows where to input Computer A’s name. In Figure

4.12, Computer A is named ‘mike’.

Step 9:

Figure 4.12: Find Computer A in My Network Places

To disconnect the PAN connection, disconnect from either Computer A or from Computer B.

♦ On Computer B, right-click on the PAN service icon and choose

Disconnect.

(Figure 4.13)

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

28

IVT BlueSoleil™ User Manual

♦ On Computer A, right-click on the PAN service icon in service window and choose Stop Service .

Figure 4.13: Disconnect the PAN service from Computer B

Advanced Usage:

♦ Computer A is now the center node. Other computers, for example, Computers

C, D and E, can connect to Computer A with BlueSoleil™ following the same steps as those for Computer B. Computer A supports up to 7 connections at the same time.

♦ Computer A, B, C, D and E can access each other using the Windows Network

Places . This forms a Bluetooth ad-hoc networking environment.

Note: It takes about 1 minute before an IP address can be obtained on the client side (Computer B) unless you select to enable the DHCP server on the server side

(Computer A).

4.3 Access LAN Through PAN-NAP

This section outlines the steps involved in accessing a Local Area Network (LAN) through a PAN-NAP.

Computer A: Ethernet PAN-NAP B:

A Bluetooth Device

Windows 2000

IVT BlueSoleil™

Step 1: Plug the LAN cable into the PAN-NAP (Ethernet PAN-NAP B) and power it on

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

29

IVT BlueSoleil™ User Manual it on.

Step 2: Insert a Bluetooth Device into the computer.

Step 3: Start BlueSoleil™ in the computer.

Step 4: Connect Computer A to Ethernet PAN-NAP B

1. Go to Computer A, double click My Device Icon until you find the device Ethernet PAN-NAP B.

2. Find the PAN service on Ethernet PAN-NAP B by double clicking the

Ethernet PAN Bridge B device icon. Enter the Bluetooth passkey (if security is set to High on either side) to start authentication. The

Enter Bluetooth Passkey window pops up on Computer A. Input the same passkey as the one on the Ethernet PAN-NAP B. (Figure

4.8)

3. Right-click the PAN service icon, and then choose Connect .

(Figure 4.15)

♦ Note: The passkey is provided by the PAN-NAP provider and the default value is usually "root". It can be modified by the software associated with the PAN-NAP. For more details please refer to the user documentation provided by the PAN-NAP provider.

Figure 4.15: Choose Connect

♦ The connection is established successfully (Figure 4.16). Wait until the valid IP address appears in the bottom right status bar on

Computer A.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

30

IVT BlueSoleil™ User Manual

Figure 4.16: Successful connection to PAN-NAP

Step 5: IP address configuration of the BT Network Adapter on Computer A.

♦ Right-click on My Network Places and select Properties .

(Figure 4.17)

♦ Right-click the Local Access Connection 2 on the Network and

Dial-up Connections window, and select Properties . (Figure

4.18)

Figure 4.17: Right-click on My Network Places

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

31

IVT BlueSoleil™ User Manual

Figure 4.18: Network and Dial-up Connections

♦ On the Local Area Connection 2 Properties window, select the

Internet Protocol (TCP/IP) item and click on Properties . (Figure

4.9)

♦ Set the IP address to be in the same subnet as the other computers in the LAN. (Figure 4.20).

Figure 4.19: Find Internet Protocol (TCP/IP)

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

32

IVT BlueSoleil™ User Manual

Figure 4.20: Set the IP address

Note: When Computer A connects to Ethernet PAN-NAP B it accesses the LAN as if it is attached to the LAN directly. The network properties of Computer A must be the same as the computers in the LAN, that is, Computer A and the computers in the LAN must be in the same subnet and have the same subnet mask. For example, if the computers in the LAN use DHCP for IP addressing, then Computer A needs to be configured to use DHCP. If the IP address is configured manually on the computers in the LAN, then Computer A also needs to be configured manually.

4.4 Access LAN Through IVT BlueSoleil™

This section outlines the steps involved in accessing a Local Area Network (LAN) through IVT BlueSoleil™.

Computer A: Computer B:

Desktop Notebook/Laptop

A Bluetooth Device

IVT BlueSoleil™

Network Adapter connecting to the LAN

A Bluetooth Device

IVT BlueSoleil™

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

33

IVT BlueSoleil™ User Manual

Step 1:

♦ Start IVT BlueSoleil™ on both Computer A and Computer B.

Please

♦ refer to “Section 3.2:Communication Between Two Computers”, and complete Steps 1 to 4.

Step 2: Start the PAN service on Computer A.

♦ In the BlueSoleil ™ Main Window, click View | Service Window.

♦ In the Service Window, right-click the Personal Area Networking icon. Choose Properties to configure my PAN service as Access

LAN Network and select a physical adapter, through which

Computer A connects to a LAN, as the LAN Adapter (Figure

4.21).

♦ Click Apply or OK button to save the configuration.

♦ Right-click the Personal Area Networking icon again, and choose

Start Service.

Step 3: On Computer B, make sure that the BT adapter has the same configuration with computers in the LAN. (Refer to Step 6 in “Section

3.3: Access LAN Through PAN”.)

Step 4: Setup connection between Computer A and Computer B. Please refer to “Section 3.2:Communication Between Two Computers”, and complete Steps 6 to 8.

Step 5:

♦ Computer B can now access the LAN.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

34

IVT BlueSoleil™ User Manual

Figure 4.21: Access Outside LAN Network Configuration

4.5 Access Internet through IVT BlueSoleil™

The following sections outline how to enable Computer B to access the Internet through Computer A.

Computer A: Computer B:

A Bluetooth Device

Windows 2000

IVT BlueSoleil™

Network Adapter connecting to the

Internet

A Bluetooth Device

Windows 2000

IVT BlueSoleil™

Step 1:

♦ Make sure Computer A can access Internet. Start IVT BlueSoleil™ on both Computer A and Computer B. Please refer to “Section

3.2:Communication Between Two Computers”, and complete

Steps 1 to 4.

Step 2: Start the PAN service on Computer A.

1. In the BlueSoleil ™ Main Window, click View | Service Window.

2. In the Service Window, right-click the Personal Area Networking icon. Choose Properties to configure my PAN service as Access

Internet and select a local physical adapter as the WAN Adapter

(Figure 4.22), through which Computer A can access Internet. It automatically enables NAT (Network Address Translation, please refer to Windows Help Topic ) function and a DHCP server.

(Notes: The BT Network Adapter on the client side must be set to obtain an IP address automatically. The IP address is in the form of 192.168.18.xxx.)

3. Click or OK button to save the configuration.

4. Right-click the Personal Area Networking icon again, and choose

Start Service.

Step 3: Setup connection between Computer A and Computer B. Please refer to “Section 3.2:Communication Between Two Computers”, and complete Steps 6 to 8.

Step 4:

♦ After Computer B gets an IP address as “192.168.18.xxx”,

Computer B can now access the Internet through Computer A.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

35

IVT BlueSoleil™ User Manual

Figure 4.22: Access Outside WAN Network Configuration

Advanced Usage:

♦ Computer A is now the center node of the network. Other computers with

BlueSoleil™ installed, for example, Computers C, D and E, can connect to

Computer A following the same steps as those for Computer B and access the

Internet through Computer A. Computer A supports up to 7 connections at the same time.

♦ Computers A, B, C, D and E can access each other using the Windows My

Network Places and form a Bluetooth ad-hoc networking. Computers B, C, D and E can then access the Internet through Computer A.

Note:

♦ Computer B also can share a dial-up connection of Computer A, in this case, please set up a dial-up connection for Computer A at first. While working with a dial-up connection, if the dial-up connection is destroyed for some reason, please restart the service after the dial-up connection established again.

♦ The Internet Connection Sharing (ICS) of Windows (refer to Windows

Help Topic ) can also be used on computer A for computer B to access the

Internet. In this situation, the PAN service configuration must be set as

Bluetooth Group Ad-hoc Network without DHCP Server enabled.

4.6.1 My PAN Service

In the BlueSoleil™ Service Window, right-click the Personal Area Networking icon.

On the pop-up menu, select Properties to configure my PAN service.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

36

IVT BlueSoleil™ User Manual

Figure 4.23: Service Configuration

Setting Items:

♦ Auto start this service when my Bluetooth starts

Check this option to automatically start my PAN service the every time

BlueSoleil™ is started.

Work Mode

♦ Set up Bluetooth Personal Area Network

Choose this item to run in the GN mode. Check Enable DHCP Server, and a

DHCP server will be started on the server side, so other devices will obtain an IP address (192.168.18.xxx) from the DHCP server after they connected to the

GN. (Refer to Figure 4.1)

♦ Access LAN Network

Choose this item to run in the NAP mode, and other devices can access outside

LAN network after they connected to the NAP. (Refer to Figure 4.3)

♦ Access Internet

Choose this item to run in the NAP mode, and other devices can access outside

WAN network (e.g. Internet) after they connected to the NAP. (Refer to Figure

4.4)

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

37

IVT BlueSoleil™ User Manual

5.1 Introduction

The Bluetooth Dial-up Networking (DUN) service allows a Bluetooth-enabled client to access the Internet wirelessly through a modem on another Bluetooth device or a cellular phone. The other Bluetooth device or the cellular phone is called the gateway (server) as it provides access to the public network.

The DUN profile can be used in the following scenario:

♦ A Bluetooth computer accesses the Internet through a Bluetooth cellular phone or Bluetooth modem.

5.2 Connect to a Dial-up Gateway from a Computer

This section outlines the steps involved in a computer (client) accessing the

Internet through a Bluetooth cellular phone.

Computer A: Bluetooth Cellular Phone:

Notebook/ Laptop

A Bluetooth Device

Windows XP

IVT BlueSoleil™

Ericsson T39 cellular phone

Step 1: Insert the Bluetooth Device in the computer and start BlueSoleil™ in the computer.

Step 2: Set the Ericsson T39 to be discoverable so that Computer A can find the T39.

1. Press the button on the T39 and scroll until you reach the

Extras menu option, select Extras and scroll until you find

Bluetooth . Select this option and scroll until you see

Discoverable . Press the Yes button to confirm the selection.

2. The T39 will now enable itself to receive connection requests from other devices.

Step 3: Add Computer A to the paired device list in the T39.

1. Press the button on the T39 and scroll until you reach the

Extras menu option, select Extras and scroll until you find

Bluetooth . Select this option and scroll until you see Discover .

Press the Yes button to confirm the selection.

2. The T39 will now start searching devices. Once the T39 finds

“ComputerA” on the screen, select it by pressing the Yes button.

The Add to paired?

message appears on the screen. Press Yes to confirm you want to initialize pairing.

3. The T39 will ask for the Bluetooth passkey. You can input any

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

38

IVT BlueSoleil™ User Manual number, for example, “1”.

4. On the BlueSoleil ™ side, the Enter Bluetooth Passkey window pops up requesting the Bluetooth passkey. Input the same

Bluetooth passkey you have input in the T39 and click OK .

5. Once the pairing process is successfully complete, the T39 device icon is displayed in the Main Window of Computer A. At the meanwhile, the following dialog pops up asking you whether

Create a Shortcut on the windows desktop . If you choose yes , a shortcut icon called DUN will occur on the desktop, otherwise the icon will not occur.

♦ This is the icon on the desktop:

Step 5: Connect to phone DUN service:

♦ Search for Bluetooth devices in Computer A until you find the T39.

♦ In the Main Window of Computer A, double click the T39 device to find its DUN service. If found, the DUN service icon in the Main

Window will turn pink.

♦ In the Main Window of Computer A, double click the DUN service icon to connect to the DUN service on the T39.

♦ Once the two computers are connected, the Bluetooth Dial-up

Networking (DUN) service icon in the Main Window will turn from pink to green.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

39

IVT BlueSoleil™ User Manual

Step 6:

Step 7:

Step 8:

Figure 5.1: Connect BlueSoleil™ DUN Connection

Dial to Internet

1. The window appears

(Figure 5.1).

2. Input a valid username, password and the Internet Service

Provider’s (ISP’s) phone number, then click the Dial button.

3. If the dial-up is successful, a small icon appears on the bottom right hand of the Windows taskbar, indicating that the dial up connection is successfully established.

4. If the dial-up fails, the Bluetooth connection between the two computers will be disconnected. In this case, to reconnect to the

T39’s DUN service, repeat Steps 5 above.

Once the dial-up connection is established, users can browse web sites or access other Internet services from Computer A.

There are three methods to disconnect the dial-up connection :

♦ Method 1. Double-click the dial-up connection icon on the bottom right of the Windows taskbar. The BlueSoleil™

DUN Connection Status window appears. Click the

Disconnect button to disconnect the dial-up connection

(Figure 5.2).

♦ Method 2. Right-click the Bluetooth Dial-up

Networking icon in the Main Window , and then click the

Disconnect menu item on the pop-up menu.

♦ Method 3. Right-click the T39 device in the Main Window and select Disconnect | Bluetooth Dial-Up

Networking .

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

40

IVT BlueSoleil™ User Manual

Figure 5.2: BlueSoleil ™ DUN Connection Status window

5.3 Settings for Dial-up Networking Profile (client side) in Windows98/Me

Before using the Dial-up Networking (DUN) profile in Windows98/Me, ensure a

Dial-up Adapter is already installed on the client computer.

5.3.1 Check if a Dial-up Adapter is installed

Step 1: Select the Control Panel from the Start |Settings menu.

Step 2: Double-click the Network icon. (Figure 5.3)

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

41

IVT BlueSoleil™ User Manual

Figure 5.3: Windows Control Panel

Step 3: Check if a Dial-up Adapter appears in the Network Component list.

(Figure 5.4)

Step 4: If a Dial-up Adapter is not found, then click Add to install one.

Figure 5.4: Install Dial-up Adapter

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

42

IVT BlueSoleil™ User Manual

Step 5: Select Adapter from the Network Component list and click Add .

(Figure 5.5 and Figure 5.6)

Figure 5.5: Network Component list

Figure 5.6: Select Adapter as the Network Component Type

Step 6: Select Microsoft from the Manufacturers list on the left-hand side and select Dial-up Adapter in the Network Adapter list on the right hand side. (Figure 5.7 and Figure 5.8)

Figure 5.7: Select Network Adapters (1)

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

43

IVT BlueSoleil™ User Manual

Figure 5.8: Select Network Adapters (2)

Step 7: Click OK to return to the Network property sheet. (Figure 5.9)

Figure 5.9: Network property sheet

Step 8: Click OK to close the Network property sheet. A message box pops up, click Yes to restart the computer. (Figure 5.10).

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

44

IVT BlueSoleil™ User Manual

Figure 5.10: Restart computer

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

45

IVT BlueSoleil™ User Manual

6 Bluetooth Serial Port

6.1 Introduction

The Bluetooth Serial Port (SPP) provides a virtual serial port via Bluetooth as an alternative to a hardwired serial cable between a computer and device. Any program that uses a standard serial port can use the Bluetooth serial port without any change.

IVT BlueSoleil™ provides three Serial Port services, you can connect with three remote devices and be connected with three remote devices at the same time through serial ports.

The SPP profile can be used in the following scenarios:

♦ Connecting two computers through a Bluetooth serial port.

♦ Using SPP to print a document.

♦ Using a cellphone to control a computer through a Bluetooth serial port.

♦ Connecting a computer to any other device that supports SPP through a

Bluetooth serial port.

This section outlines the steps involved in connecting two computers, Computer A and Computer B using the Bluetooth Serial Port application.

Computer A: Computer B:

Notebook/ Laptop

A Bluetooth Device

Windows 2000

Desktop

A Bluetooth Device

Windows 2000

IVT BlueSoleil™ IVT BlueSoleil™

Step 1: Insert the Bluetooth Devices into each computer.

Step 2: Start BlueSoleil™ in each computer.

Step 3:

♦ Start the SPP service on Computer A.

Step 4: Connect Computer B to Computer A.

1. On Computer B double click the ‘My Device icon’ until you find the device, Computer A.

2. Double-click the Computer A device to find its SPP service (Figure

6.1). The Bluetooth Serial Port service icon turns pink.

3. Right-click the Bluetooth Serial Port service icon and select

Connect .

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

46

IVT BlueSoleil™ User Manual

Figure 6.1: Double-click the Computer A device icon

♦ The connection is established successfully as shown in Figure 6.2.

And the serial port number is shown on the right bottom status bar on Computer B. (Figure 6.3)

Figure 6.2: The connection is established successfully

Figure 6.3: The serial port number is shown

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

47

IVT BlueSoleil™ User Manual

Note: You can initiate three connections between the two computers through three serial ports. And at the same time, you can also be connected with three remote devices if you provide three SPP services.

6.3 Use SPP to Print a Document

This section outlines the steps involved in connecting a computer to a Bluetooth

Printer Adapter using SPP.

Computer A: Bluetooth Printer Adapter B:

Notebook/Laptop Printer

A Bluetooth Device

Windows 2000

IVT BlueSoleil™

Bluetooth Printer Adapter

Step 1: Insert the Bluetooth Device into the computer.

Step 2: Start BlueSoleil™ in the computer.

Step 3: Connect Computer A to the Bluetooth Printer Adapter B using SPP.

1. Go to Computer A; double click the My Device icon’ until you find the device Bluetooth Printer Adapter B.

2. Double-click the Bluetooth Printer Adapter B device to find it’s SPP service.

3. Double-click the SPP service icon to start connecting SPP.

Step 4: Change the printer settings to use the connected Bluetooth serial port.

Step 5:

♦ Print a document.

6.4 Use a cellphone to control a computer

This section outlines the steps involved in connecting a computer to a Bluetooth

Cellphone using SPP.

Computer A: Bluetooth Cellphone B:

Notebook/Laptop

A Bluetooth Device

Windows 2000

IVT BlueSoleil™

Ericsson T39 or T68

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

48

IVT BlueSoleil™ User Manual

Step 1: Insert the Bluetooth Device into the computer.

Step 2: Start BlueSoleil™ in the computer.

Step 3: Connect Computer A to the Bluetooth Cellphone B using SPP.

1. Go to Computer A; double click the My Device icon’ until you find the device Bluetooth Cellphone B.

2. Double-click the Bluetooth Cellphone B device to pair with it. If pairing is finished successfully, then find it’s SPP service.

3. Double-click the SPP service icon to start connecting SPP.

4. The connected serial port number is shown on the right bottom status bar on Computer A. (Figure 6.4)

Figure 6.4: The serial port number is shown

Step 4: Select Start|Program|IVT Corporation|Control PC to open

Mobile HID program. (Figure 6.5)

Figure 6.5: Mobile HID Program Dialog

Step 7: From the Serial Port list in the “Remote Control” window, select the serial port number that has been established connection. Then click

Open button to enable Cellphone B controlling computer A. The Open button becomes to Close button automatically. (Figure 6.6)

Figure 6.6: Click button to start controlling computer

Step 8: A new menu will be added into the accessories menu in Cellphone B.

Enter menus by the path: accessories -> Mobile HID -> Control PC ->

Controlling. When Controlling window is shown, you can control

Computer A by all keys in Cellphone B.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

49

IVT BlueSoleil™ User Manual

Step 9: If you want to disable Cellphone B controlling computer A,click Close button. The Close button becomes to Open button automatically. Or press down the No key in Cellphone B to exit Controlling window.

Key 2

Key 3

Key 4

Key 5

Key 6

Key 7

Key 8

Key 9

The function of cellphone key map:

Keys in cellphone Function definition

Up,Down,Left,Right direction key

Key Yes

Press down direction key (T68) mouse move

(no UP,Down in T39)

Mouse left button

Mouse right button

Key c (T39)

Volume Up

Volume Down

Key 1

Mouse right button

Page Up

Page Down

Home

Key 0

Key *

Key #

Arrow Up

End

Arrow Left

Arrow Down

Arrow Right

Start menu

Key Enter

Key F5

Show desktop

Key Ctrl

Key Alt

6.5.1 My SPP Service

In the BlueSoleil™ Service Window, right-click the Serial Port 1 or Serial Port 2 icon. On the pop-up menu, select Properties to configure the Serial Port1 and

Serial Port 2.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

50

IVT BlueSoleil™ User Manual

Figure 6.9: SPP Service Configuration.

Setting Items:

♦ Auto start this service when my Bluetooth starts

Check this option to automatically start my Bluetooth SPP service #(1,2) every time BlueSoleil™ is started. (Figure 6.9)

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

51

IVT BlueSoleil™ User Manual

7 Bluetooth File Transfer

7.1 Introduction

The File Transfer profile (FTP) supports the file transfer usage model, which offers the ability to transfer files from one Bluetooth device to the other.

The FTP profile can be used in the following scenarios:

♦ A computer can transfer files to/from another computer.

7.2 Transfer files to/from a Computer

This section outlines the steps in transferring files between Computer A and

Computer B.

Computer A (Server) Computer B (Client)

IVT BlueSoleil™

A Bluetooth Device

IVT BlueSoleil™

A Bluetooth Device

Note: BlueSoleil™ can inter-operate with other Bluetooth devices which support

FTP profile.

Step 1: Insert the Bluetooth Devices into each computer.

Step 2: Start BlueSoleil™ in each computer.

Step 3: Make sure File Transfer service is started on Computer A. Refer to

Section 7.3 for service configurations.

Step 4: Search for Computer A on Computer B, and connect to its FTP service

(Figure 7.1). The remote folder is displayed in a Windows Explorer style window (Figure 7.2).

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

52

IVT BlueSoleil™ User Manual

Figure 7.1: The connection is successfully established

Figure 7.2: The remote folder is displayed

Step 5: Copy files and directories.

♦ From Computer B to Computer A – upload

Select files\ directories on Computer B and drag files into the

Remote Shared Folder. (Figure 7.3)

♦ From Computer A to Computer B – download

Select files\ directories from the Remote Shared Folder and drag files into the desktop or a folder on Computer B. (Figure 7.4)

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

53

IVT BlueSoleil™ User Manual

Figure 7.3: Upload files to Computer A

Figure 7.4: Download files from Computer A

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

54

IVT BlueSoleil™ User Manual

In the BlueSoleil™ Service Window, right-click the File Transfer icon. On the pop-up menu, select Properties to configure the ‘my FTP service’ (Figure 7.5).

Figure 7.5: Configure FTP service

Setting Items:

♦ Auto starts this service when my Bluetooth starts

Check this box to automatically start the File Transfer service every time

BlueSoleil™ is started.

♦ Root Directory

This sets the root directory that you want to share with other computers using

Bluetooth.

♦ Access Permissions

This sets the access permission remote computers have to the shared root directory.

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

55

IVT BlueSoleil™ User Manual

8.1 Introduction

The Bluetooth LAN Access Profile (LAP) allows Bluetooth-enabled devices to access the services of a LAN using Point-to-Point Protocol. In this usage model, multiple data terminals use a LAN access point as a wireless connection to a Local Area

Network (LAN). Once connected, data terminals operate as if they are connected to the LAN via dial-up networking and can access all the services provided by the LAN.

The LAN application can be used in the following scenarios:

♦ A computer (or PDA) accesses a Local Area Network via a LAP Server.

♦ A computer (or PDA) accesses a Local Area Network via a LAN access point.

Note: Before using the LAN Access Profile in Windows98/Me, ensure that a

Dial-up Adapter and Windows’s component direct cable are already installed on the computer. (See “Section 8.4: Settings for LAN Access Profile (client side) in

Windows98/Me”). Moreover, every operating system should have an installation of

NetBEUI protocol; otherwise, it cannot use computer name to visit other computer.

8.2 Access a Local Area Network (LAN)

This section outlines the steps involved in connecting to a Local Area Network using the LAP application.

Computer A: Computer B:

Notebook/ Laptop

A Bluetooth Device

Windows 2000

Desktop

A Bluetooth Device

Windows 2000

IVT BlueSoleil™ IVT BlueSoleil™

Step 1: Insert Bluetooth Devices into both computers.

Step 2: Start BlueSoleil™ in both computers.

Step 3:

♦ Start the LAP service on Computer A.

Step 4: Make incoming connection on Computer A

♦ Right-click on My Network Places ; select Properties. (Figure

8.1)

♦ On the Network and Dial-up Connections panel, right-click the

Incoming Connection icon, and then select Properties on the pop up menu. (Figure 8.2)

Copyright © 2001, IVT Corporation, http://www.ivtcorporation.com

All specifications are preliminary and subject to change without notice.

56

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals