ROUSH R2300 Phase 1, Phase 2 supercharger kit Installation instructions
Below you will find brief information for supercharger kit R2300 Phase 1, supercharger kit R2300 Phase 2. These instructions give you a detailed step-by-step guide on how to install the ROUSHcharger kit for 2005-09 Ford Mustang GT vehicles with 4.6L 3V engines (manual transmissions only). They will guide you through the necessary modifications, subassembly, and assembly steps required for proper installation.
Advertisement
Advertisement
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
2005-09 R2300 Phase 1 & 2 ROUSHCharger Kits (Single Sheave)
P/Ns: 1305SS-TVSP1
1305SS-TVSP2
NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Installation Instructions
Applications:
2005
– 09 Ford Mustang GT with 4.6L 3V engine (w/ Manual Transmissions ONLY)
Important Notes:
Before installing your Mustang ROUSHCharger Kit, please read the installation manual and verify that all items are present. Contact ROUSH Customer Service at 1-800-59-ROUSH,
9:00 AM to 5:00 PM weekdays, for any questions regarding fit or instructions that are unclear to you.
Premium fuel (91 octane or higher) is required to prevent “spark-knock” or detonation under certain operating conditions.
The use of fuel additives (ie. octane boosters) is not recommended. These chemicals can damage your engine and cause drivability issues with your vehicle.
Operating your engine without the Roush PCM recalibration will result in engine damage or failure.
Customers with 2005 - 07 and 2008 (with “AA” level engines) vehicles have high thread (HT)
14mm spark plugs. These customers will receive colder replacement 14mm plugs from
Roush when their PCM is returned to them.
Customers with 2008 (with “AB” level engines) and 2009 vehicles have 12mm spark plugs
(Ford P/N: 8L3E-12405-BB). These customers MUST gap their plugs to 0.032 +/-
0.002”.
Customers with 2009 vehicles must also refer to pages 79-84 for special instructions.
1305SS-TVSIM-BA 20130911 Page 1 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
PACKAGING LIST
Description
Fuel Charging
Manifold Assembly
– Fuel Charging
Supercharger Assembly (P51a w/ Bolt-On Hub)
Bolts
– S/C Pulley (M6 x 14)
Throttle Body Spacer Assembly
Throttle Body Assembly
Fuel Rail
Tube Assembly
– Heater Water Inlet
Spark Plugs (FOR MY2005-2008.5 ONLY)
RPP Part Number
Qty
---
R07060135
P51AH-6F066
1
1
N605771
R07060147
R07060150
R07110006
R07070063
HTO-032
1
8
6
1
1
1
Description
Hardware Kit B
– Fuel Charging
Fuel Injectors
Fuel Injector Clip
PCV Bubbler Hose
¾” Hose – Heater Jumper Hose
Clamp
– ¾” Hose (Constant Tension)
Gasket
– Spacer to Supercharger
Gasket
– Throttle Body to Spacer
Screw & Washer
– T-Body & S/C to Spacer (M6 x 1.0 x 32.5)
Bolt
– Fuel Charging To Cylinder Head (M6 x 1.0 x 40)
Bolt
– RH Fuel Rail To Upper Intake Manifold (M6 x 1.0 x 22)
Bolt
– S/C To Upper Intake Manifold
Stud
– S/C To Upper Intake Manifold
Nut
– Heater Tube Mounting (M6)
RPP Part Number Qty
13106066TVSHKB 1
R07110007 8
13109C995
R07060175
R07070067
CT19x12-BO
8
1
1
2
R07060152
R07060153
R18020009
R18020004
R18020057
N808130
R18040007
W520412
11
2
8
2
2
1
1
8
Description
FEAD
Alternator Bracket
Tensioner
RPP Part Number
Qty
--- 1
R07020035 1
R07020043 1
Description
Hardware Kit
– Single Sheave FEAD
Pulley - Idler B/S 76mm (Flanged)
Bracket
– Alternator Rear Support
Bolt
– Rear Alternator Support Bracket (M5 x 10)
Nut
– Rear Alternator Support Bracket (M5)
Bolt
– Idler (M8 x 28 large washer)
Bolt
– Alternator (M8 x 55)
Bolt
– Alternator Support Brkts to Intk (M8 x 25)
Bolt
– FEAD Bracket to Intake (M8 x 38)
Bolt
– Alternator Bracket to S/C (M8 x 110)
Nut
– Alternator (M8)
RPP Part Number Qty
SS-TVSHK1-AA 1
R07020049
R07020052
2
1
R18020059
R07020053
R18020060
N808130
2
2
2
2
W500224
W705128
R18020058
W520413
1
2
1
2
1305SS-TVSIM-BA 20130911 Page 2 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Spacer
– Alternator Bracket To S/C (3/8” ID x 3/4” OD x 3/8”)
R18030017 1
Description
Induction System
Clean Air Tube Assembly
Shelby Clean Air Tube
Air Filter
– High Flow Conical
Shelby Air Box Assembly
RPP Part
Number
---
1305-9B659
R07060101
R07060131
R07130039
Qty
1
1
1
1
1
Description
Induction System Hardware Kit
Clamp
– Worm Drive (120 – 140)
Clamp
– Worm Drive (110 – 130)
MAF Bolts (M4 x 0.7 x 10
– Torx)
Grommet and Sleeve Assembly
Clean Air Tube Support Bracket
Bolt
– Bracket to Tube and Air Box
Bolt
– Air Box to ABS Bracket
3/16 VACUUM CAP - BOOST REFERENCE PORT
VACUUM FITTING - BOOST REFERENCE PORT
3/8 VACUUM CAP - BRAKE ASPIRATOR PORT
3/8 x 3/8 VACUUM CONNECTOR - BRAKE ASPIRATOR PORT
RPP Part
Number
R07130040
R07130014
R07130015
R07130007
R07130013
R07130010
N605771
N808920
4440
383004-S
CS2575
P2233A
Qty
2
1
1
3
1
1
1
1
1
1
1
1
Description
Emission
PCV Fresh Air Inlet
PCV Purge Hose
7/32” Vacuum Hose – IPTS to Upper Intake Manifold
RPP Part
Number
---
R07050083
R07050084
R18140001
Qty
1
1
1
1
Description
Hardware Kit
– Wiring
Electrical Jumper
– I/C Pump
Electrical Jumper
– ACT
TPS Extension
Bolt
– Ground Strap To Cowl (M6 x 1.0 x 18)
Zip Tie (Stud Mount)
– Ground Strap Bolt
Bolt
– I/C Fuse Mounting (M6 x 1.0 x 14)
Nut
– I/C Relay Mounting (M6)
Alternator Charge Harness
– B+ Cable
Alternator Charge Harness
– Smart Charge
RPP Part
Number
R07080035
Qty
1
R07080016 1
1104-12B637-BA 1
R07080031
N605891
R18080003
N605771
1
1
1
1
W520412
R07080032
R07080033
1
1
1
1305SS-TVSIM-BA 20130911 Page 3 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Description
Hardware Kit
– Single Sheave Decals
Decal
– Single Sheave Belt Routing Diagram
Decal
– Premium Fuel Only (IP Cluster)
Decal
– Premium Fuel Only (Fuel Door)
Decal
– PCM
RPP Part Number
Qty
SS-TVSHK2-AA 1
13106E072 1
R07110004
R07110003
R07100008
1
1
1
Description
Intercooler System
Degas Bottle
I/C Electric Water Pump
Bracket
– I/C Pump Mounting
Intercooler Radiator Assembly
Lower Radiator Hose
RPP Part
Number
---
R07070007
F8YZ-8501-A
Qty
R07070015
R07070047
1
1
7R33-8B273-AA 1
1
1
1
Description
Intercooler Hose & Steel Tube Kit
Tube Assembly
– Heater Water Inlet
Tube Assembly
– CAC Lines
¾” Hose – Degas Inlet
¾” Hose – Degas Outlet
¾” Hose – LTR Inlet
¾” Hose – LTR Outlet
Hose
– I/C Water Inlet
Hose
– I/C Water Outlet
¾” Hose – Heater Tube Inlet
Upper Radiator Hose
Clamp
– ¾” Hose (Worm Drive)
Clamp
– ¾” Hose (Constant Tension)
Hose with Clamps
– PCV Bubbler
RPP Part
Number
R07070074
R07070063
R07070005
R07070006
R07070008
R07070010
R07070013
R07060173
R07060174
R07070067
R07070022
---
---
R07060175
Qty
1
4
10
1
1
1
1
1
1
1
1
1
1
1
RPP Part
Number
R07070075
XL3Z-8100-A
N623332
R07030002
R18020010
R18030002
N605891
N808429
R18020007
R18020006
W520412
W520413
Qty
Description
Intercooler Hardware Kit
Degas Bottle Cap
J-clip
– Degas Bottle & Pump Bracket Mounting (M6 Short)
Double-sided Tape
– Degas Bottle Mounting
Cap Screw
– Degas Bottle Mounting (M6 x 1.0 x 8)
Washer
– M6 x 18mm OD
Bolt
– Pump Bracket & I/C Tube Assembly Mounting (M6 x 1 x 18)
Bolt
– Degas Bottle Mounting (M6 x 1.0 x 33)
Bolt
– Long Bumper Bolts (M8 x 1.25 x 35)
Bolt
– 9N491 Tube Assembly Mounting (M16 x 40)
Nut
– Heater Tube Mounting to S/C (M6)
Nut
– LTR Mounting & Pump Bracket (M8)
1305SS-TVSIM-BA 20130911 Page 4 of 87 1-800-59-ROUSH
1
1
1
3
1
1
4
2
4
1
2
5
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
RPP Part
Number
1305-TVSHK1
R07080034
R07020045
R18020005
Qty
Description
Supplemental Hardware
Alternator Charge Harness
– 2009 Only
Rear Alternator Support Bracket (2005-08 Only)
Bolt
– Rear Alt Supt Brkt (M8 x 20mm)
Description RPP Part Number
Qty
Unique Phase 1 Hardware
Pulley
– S/C Bolt-On (6K x 105mm)
FEAD Belt
CALKIT
ROUSH Diagnostic Tool Flash Manual
Optional Roush PCM Flash
Flash Voucher Card
Description
6K105-6V066
R07020041
1305-P1CALKIT
RDT-CALIM
PCM-FLASHDOC
P1305-P1
RPP Part Number
Qty
1
1
1
1
1
1
1
1
1
1
Unique Phase 2 Hardware
Pulley
– S/C Bolt-On (6K x 80mm)
FEAD Belt
Ford Racing 2005-09 S197 Fuel System Upgrade Kit
Nut
– M6 (2 nd
FPDM Retention)
CALKIT
ROUSH Diagnostic Tool Flash Manual
Optional Roush PCM Flash
Flash Voucher Card
6K80-6V066
R07020062
R14020001
W520412
1305-P2CALKIT
RDT-CALIM
PCM-FLASHDOC
P1305-P2
2
1
1
1
1
1
1
1
1305SS-TVSIM-BA 20130911 Page 5 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
EQUIPMENT AND SUPPLIES REQUIRED
1/4” and 3/8” Drive Ratchets with Extensions
Metric and Standard Socket Sets (short and deep recommended)
1/2” Drive Ratchet or Breaker Bar
Metric and Standard Wrench Sets
3/8” Drive Torque Wrench (7-35 ft-lb range)
Short Phillips-head Screwdriver
Hex Key Set
Teflon pipe sealing tape or equivalent
5/8” Fuel Line Removal Tool
T-20 Torx Bit Screwdriver or Socket
Soldering Iron and Solder
Wire Strippers
Wire Crimpers “W” type for OEM-style wiring connectors
1/8”, 9/64”, and ¼” Drill Bits and Drill motor
Coolant (meeting G-05 specification)
6” Scale, Tape Measure, or Other Measuring Device
Brake Parts Cleaner
Assembly Lubricant (White Lithium Grease or Petroleum Jelly)
Electrical Tape
Sharp Knife or Razor Blade
Tie Straps (Zip Ties)
Trim Pad Tool (for pushpin removal)
Fender Cover (2)
Medium Strength Thread Locker
– Loctite 242 (blue) or equivalent
GLOSSARY OF TERMS
ACT
CMCV
ETC
IPTS
MAFS
PCM
PCV
RDT
SCBP
TPS
VMV
VCT
Breakout Point
Air Charge Temperature Sensor (From the factory, this function is integrated into the MAF sensor. With this kit, a separate ACT sensor is installed into the intake manifold)
Charge Motion Control Valve (Located on the back of the base intake manifold. This feature is not used with the ROUSHCharger)
Electronic Throttle Control
Injection Pressure and Temperature Sensor
Mass Air Flow Sensor
Powertrain Control Module (a.k.a. ECM, ECU, PCU, EEC)
Positive Crankcase Ventilation
ROUSH Diagnostic Tool
Supercharger Control Bypass Solenoid (A 3-way electronic vacuum control solenoid that allows the PCM to control the ROUSHCharger bypass to reduce heat buildup and noise during low throttle operation)
Throttle Position Sensor
Vapor Management Valve (Located on driver side strut tower)
Variable Camshaft Timing
A place in an electrical harness where the wiring for an individual component leaves (breaks out of) the main harness to attach to an individual component.
1305SS-TVSIM-BA 20130911 Page 6 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
INFORMATION ABOUT THE SUPERCHARGER BYPASS OPERATION
There is a great deal of misinformation about the function of supercharger bypass systems. The supercharger is a positive-displacement pump; that is, so long as it is rotating, it is always pumping air. During low demand or high vacuum operation (i.e. idle, deceleration, and light throttle cruise), the pumping action is undesirable as it creates unwanted heat and noise. The bypass circuit, when open, prevents any pressure buildup across the supercharger and allows air to circulate through the rotors, allowing the supercharger to “idle” freely during these conditions. This results in reduced noise, and by reducing heat buildup in the intake, significantly improves street and strip performance. As throttle demand increases, the bypass circuit is closed, resulting in full performance from the supercharger. The bypass circuit is never used to limit or control boost during full-throttle operation and defeating or altering the bypass function will not result in improved performance in any condition, and will result in poor drivability.
LIMIT OF LIABILITY STATEMENT
The information contained in this publication was accurate and in effect at the time the publication was approved for printing and is subject to change without notice or liability. ROUSH Performance Products (RPP) reserves the right to revise the information presented herein or to discontinue the production of parts described at any time.
SAFETY REQUIREMENTS
STOP! READ IMPORTANT SAFETY CAUTIONS AND WARNINGS BEFORE
PROCEEDING.
IMPORTANT SAFETY NOTICE
Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the actual installation.
1. Always wear safety glasses for eye protection.
2. Place ignition switch in the OFF position.
3. Always apply the parking brake when working on a vehicle.
4. Block the front and rear tire surface to prevent unexpected vehicle movement.
5. If working without a lift, always consult vehicle manual for correct lifting specifications.
6. Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide.
7. Do not smoke or use flammable items near or around the fuel system.
8. Use chemicals and cleaners in well-ventilated areas.
9. Batteries produce explosive gases, which can cause personal injury. Therefore, do not allow flames, sparks or flammable substances to come near the battery.
10. Keeps hands and any other objects away from the radiator fan blades.
11. Keep yourself and your clothing away from moving parts when the engine is running.
12. Do not wear loose clothing or jewelry that can get caught in rotating parts or scratch surface finishes.
13. Allow the engine, cooling system, brakes and exhaust to cool before working on a vehicle.
WORK SAFELY!
Perform this installation on a good clean level surface for maximum safety and with the engine turned off.
1305SS-TVSIM-BA 20130911 Page 7 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
SECTION A - DISASSEMBLY
The following section will guide you through the disassembly of the stock components. Special care should be taken to label fasteners and parts that are taken off during this procedure since many will be reused:
1.
Cover both fenders with fender covers to protect the vehicle finish.
2.
Release the fuel system pressure (NOTE: The following procedure is taken directly from the Ford
Service Manual, section 310-00).
WARNING: Fuel in the fuel system remains under high pressure even when the engine is not running. Before working on or disconnecting any of the fuel lines or fuel system components, the fuel system pressure must be relieved. Failure to do so can result in personal injury.
WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel-related components. Highly flammable mixtures are always present and can be ignited, resulting in personal injury.
a. Remove the fuel pump module fuse.
NOTE: The fuel pump module fuse is located in the bussed electrical center, location F41.
1305SS-TVSIM-BA 20130911 Page 8 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
b. Start the engine and allow it to idle until it stalls. c. After the engine stalls, crank the engine for approximately 10 seconds to make sure the fuel injector supply manifold pressure has been released. d. Turn the ignition switch to the OFF position.
3.
Using an 8mm wrench, disconnect the (-) negative & (+) positive connections to the battery.
Remove the battery hold down bolt using an 8mm socket wrench. Remove the hold down & battery. With an 8mm socket wrench, remove the 3 bolts holding the battery tray to the vehicle.
Remove the battery tray.
Battery Tray Bolts
1305SS-TVSIM-BA 20130911 Page 9 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Before continuing, refer to the CALKIT included with your ROUSHcharger kit.
Determine the PCM flash method you will be using. If performing the PCM flash
yourself or at a preferred ROUSH dealer, proceed to step 5. If sending the PCM to
ROUSH for a ROUSH performed PCM flash, continue with step 4.
4.
Disconnect the 3 PCM (Powertrain Control Module) connectors by lifting the grey levers over the connector back shell and lifting the connectors from their sockets. Remove the PCM by removing two 10mm bolts and pulling the PCM forward and lifting out of the engine compartment. Follow the instructions on the next page as soon as possible to help minimize the amount of time you are without a PCM.
Connector
Locations
Retaining Bolts
Important: Be sure to write your VIN number and phone number (in case we need to contact you for additional vehicle information) on the PCM using a permanent marker.
1305SS-TVSIM-BA 20130911 Page 10 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
INSTRUCTIONS FOR RETURNING THE PCM TO ROUSH FOR CALIBRATION
Outlined below are the instructions for returning your stock powertrain control module (PCM) to Roush
Performance Products so we can install our calibration to make the engine run properly with the new components. Please complete
the “Optional Roush PCM Flash” request document and include it, along with the PCM,
and the “Voucher Card”. Once we receive your PCM, we will reprogram and return it back to you the same day for next-day delivery. Operating your engine without our
calibration will result in engine damage or failure and will void all warranty.
Note: It is important to reinstall the PCM in the vehicle it came from to prevent setting a trouble code and having to relearn the anti-theft code which can only be performed using specialized Ford Service Bay tools.
If you haven’t already done so, write your vehicle identification number (VIN) and phone number
on the PCM using a permanent marker.
Using bubble wrap, or another appropriate packing material, wrap and package the PCM to help prevent it from being damaged during shipping.
Place the wrapped PCM in an appropriate shipping box.
Complete the “Optional ROUSH PCM Flash” request document (PCM-FLASHDOC) and attach the flash “Voucher Card” (P1305-P1CALKIT/P1305-P2CALKIT) to the document.
Include the
“Optional ROUSH PCM Flash” document and the “Voucher Card” in the
shipping box, along with the PCM.
Ship the PCM and contents to:
ATTN: PCM FLASH
39555 Schoolcraft Rd
Plymouth, MI 48170
Upon receipt of the PCM, a customer service representative will contact you to arrange payment.
Once you receive your ROUSH flashed PCM, reverse step 4 for PCM installation.
1305SS-TVSIM-BA 20130911 Page 11 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
5.
With the engine cool, remove the cap on the engine coolant degas bottle and drain the coolant using the petcock located on the lower passenger side of the radiator.
TIP: Connect 3/8” hose to the drain fitting next to the petcock and run into a clean drain pan or bottle.
Use a ¾” wrench to open petcock and allow coolant to drain out of the fitting.
Drain Petcock
6.
Disconnect the PCV vent tube from the right-hand cam cover and clean air tube. Using an 8mm nut driver, loosen the 2 clamps at either end of the clean air tube. Remove the clean air tube from the throttle body and airbox.
Clamps
PCV Vent
Tube
1305SS-TVSIM-BA 20130911 Page 12 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
7.
Remove the MAF (mass air flow) connector by pulling the red locking tab back and pressing the black release tab. With a 10mm socket wrench, remove the airbox hold down bolt. Firmly grasp the airbox and pull up to remove it from the vehicle.
Hold down bolt
MAF Connector
8.
Disconnect ETC (electronic throttle control) & TPS (throttle position sensor) connectors from the throttle body (Pull the red locking tab back; press the black release tab to disengage the lock).
9.
Remove the PCV line from the intake manifold and left-hand cam cover. Remove the VMV line from the intake manifold and position out of the way. Remove the vacuum line and electrical connector from the IPTS on the fuel rail and save for reuse. Remove the black safety clip from the fuel line connection. Place rags under the fuel rail, using a 5/8
” fuel line tool (wrap additional rags around the tool) disconnect the fuel line from the fuel rail.
VMV Line
IPTS
Fuel Rail Disconnect
PCV Line
1305SS-TVSIM-BA 20130911 Page 13 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
10.
Disconnect the alternator harness from the positive battery terminal and remove the harness clips from the fuel rail studs.
.
11.
Disconnect the wiring connectors from the fuel injectors (8). Remove the four 8mm stud bolts holding the fuel rail to the intake manifold and remove the fuel rail assembly with injectors. There may be some additional fuel leakage around the injectors. Clean all excess fuel before proceeding.
Fuel Rail Holdown Studs
1305SS-TVSIM-BA 20130911 Page 14 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
12.
Disconnect the CMCV connector located in the center rear of the intake manifold. Remove the brake booster vacuum line from the intake manifold. Pull the wiring harness off of the stud bolt on the driver side rear of intake manifold. Remove the ten fasteners which used to bolt the intake manifold to the cylinder heads. Save the rear stud for reuse. Remove the intake manifold. Use tape or equivalent to cover the cylinder head ports to prevent engine contamination.
Brake Booster Hose
Intake Manifold Bolts
Stud
CMCV Connector
Wire Harness hold down
13.
Release the accessory drive belt by rotating the tensioner clockwise with a ½
“ breaker bar or ratchet and slip the belt off the water pump pulley and remove the belt. Disconnect the regulator connector and the battery cable from the alternator. Using a 10mm socket wrench, remove the four upper support bracket bolts. Remove the two 15mm alternator nuts and remove the alternator.
1305SS-TVSIM-BA 20130911 Page 15 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
14.
2005
– 06 VEHICLES ONLY - Remove the upper radiator and bypass circuit hoses. Remove the clamps from the upper radiator hose and save for later use. On the back side of the water crossover, disconnect the heater hose. Remove the water crossover using a 10mm socket wrench.
Crossover Tube Bolts
Upper Rad Hose
Heater Hose
Thermostat Hose
14.
2007
– 09 VEHICLES ONLY - Remove the upper radiator hose. On the back side of the water crossover, disconnect the heater hose. Remove the water crossover using a 10mm socket wrench.
Crossover Tube Bolts
Upper Rad. Hose
Heater Hose
1305SS-TVSIM-BA 20130911 Page 16 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
15.
Disconnect the rubber portion of the heater hoses from the metal tubes at the rear of the righthand cylinder head. Remove the heater tube assembly from the engine by removing the stud on the back side of the passenger cylinder head and sliding off the water pump fitting in the block.
Disconnect Heater Hoses Here
Stud Bolt
16. 2005
– 06 VEHICLES ONLY - Locate the coolant hose hanger on the front of the engine and remove.
1305SS-TVSIM-BA 20130911 Page 17 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
17. Remove the tensioner and retain the bolts for reuse later.
1305SS-TVSIM-BA 20130911 Page 18 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
SECTION B - MODIFICATIONS
The following section will guide you through the required modifications of existing components and build up of the assemblies used to complete the installation. With the exception of the intercooler pump bracket mounting, all of this work can be performed away from the vehicle.
Alternator Modification
In order for the alternator to be installed in its new location, two of the original mounting ears must be removed. Using a band saw or similar cutting tool, remove the mounting ears shown. Be careful to avoid getting debris inside of the alternator when removing these features.
2005-08 Alternators should look similar to the pictures below:
Before After
2009 Alternators should look similar to the pictures below once mounting ears have been removed:
1305SS-TVSIM-BA 20130911 Page 19 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
VMV Modification
1.
Remove split loom convolute from stock VMV hose assembly.
2.
Mark hose at 130mm (~5.25in) from end of straight connector.
130 mm
3.
Using a knife, cut the hose at the applied mark
.
1305SS-TVSIM-BA 20130911 Page 20 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
4.
Using a knife, cut the hose as shown to remove the straight connector from the cut off piece of
VMV hose.
5.
Re-install straight connector into shortened VMV hose.
6.
Using a knife, cut off 100mm (~4 in) of split loom convolute to fit the shortened VMV line. Reinstall the split loom convolute onto the modified VMV hose.
1305SS-TVSIM-BA 20130911 Page 21 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Brake Booster Hose Modification
Note:
This modification does not require removal of the hose from the booster.
Removing the hose from the booster could damage the booster fitting
.
1.
Remove the split loom convolute from brake booster hose. Remove the T-fitting with the 7/32” vacuum hose and the short hose from the brake booster hose assembly.
2.
Remove and keep Tfitting with the 7/32” vacuum hose and hose clamp from the take off brake booster hose. Discard short section of the brake booster hose.
Discard
3.
Remo ve and discard the 7/32” vacuum hose retaining clip. Measure and mark 45mm from the end of the 7/32” vacuum hose. Use a knife to cut the vacuum hose at mark
.
Discard
1305SS-TVSIM-BA 20130911 Page 22 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
4.
Mark the brake booster hose 80mm from end. Using a knife, cut the brake booster hose at the applied mark.
5.
Re-install T-fitting with the 7/32 vacuum hose onto the cut brake booster hose.
6.
Install the 80mm piece of hose, which was cut off in step 3, on the open end of T-fitting
.
1305SS-TVSIM-BA 20130911 Page 23 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
7.
Install the hose clamp onto the end of the 80mm hose.
Heater Tube Assembly Modification
1.
The upper tube and hose on the heater tube assembly is not used (a new tube is supplied in the kit). Using a die grinder or air saw, cut the forward bracket that connect the two tubes together and cut along side of the rear bracket through the upper tube. De-burr all sharp edges. Retain the lower tube which connects to the water pump and the mounting bracket for reinstallation.
Discard this tube
Cut
Save
1305SS-TVSIM-BA 20130911 Page 24 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Wiring Harness Modifications
The following details the modifications to the factory engine harness which are necessary to complete the installation of this kit. These modifications should be done without removing the harness from the engine as it will be easier to verify final locations of the break out points.
Extreme care must be taken to insure that wiring and/or its insulation is not accidentally damaged while removing the convoluted tubing. All of the convoluted tubing and various clips that are removed while making these changes are intended to be reinstalled in the same place unless otherwise noted.
TPS
ETC
MAF
Connectors for Wiring Circuits that will need to be modified
1305SS-TVSIM-BA 20130911 Page 25 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
1.
Make a note of the locations of the harness retaining clips and breakout points. With the harness still fastened to the engine with the factory retainers, carefully cut the tape off of the convoluted tubing and wiring harness on the drivers side of the engine (where the ETC branches out of the main harness) using a razor or utility knife. The area is highlighted in the following diagram. The convoluted tubing is split from the factory so follow the split. Lift the wiring out of the convoluted tubing without disturbing the factory retainers wherever possible. Expose all of the internal wiring from the MAF/ETC split all the way around to the rear of the driver side cam cover.
Pull wiring out from this section.
2.
Locate the 6-wire MAF sensor connector. Looking into the face of the connector with the release tab positioned up, the first two wires in the connector (IAT) from the right are grey and grey w/ red tracer. Cut both of these wires approximately 5 to 6 inches from the back of the connector.
1305SS-TVSIM-BA 20130911 Page 26 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
3.
Seal the connector side of both cut IAT wires with pieces of heat shrink provided in the ACT electrical jumper (1104-12B637-BA). Place two pieces of heat shrink tubing halfway onto the ends of the wires to be sealed and heat with a heat gun until it stops shrinking and sealant flows out from the open end of the tubing.
Sealing cut wire ends with Heat Shrink tubing
4.
Drag the 2 IAT wires out of the harness back from the MAF connector so that they break out
60mm past the #6 Coil Connector. Strip a ¼ inch of insulation from the end of each wire. Slide a short length of heat shrink tubing over both wires. Now using the Electrical Jumper (ACT) from the kit (1104-12B637-BA) lay the striped end of the Gray (IAT) wire into one side of the provided splice connector. From the Electrical Jumper (ACT) slide the ACT SIGNAL wire into the other side of the splice connector, and crimp using a W type crimping tool. Using a clean hot soldering iron, heat the wires (not the solder) in the splice connector until they are hot enough to melt the solder touched to them. Repeat the above for the IATRTN
– ACT GROUND. Slide the heat shrink tubing over the solder joints and heat to shrink with a heat gun. Position the ACT harness so that the base of the connector is 180mm from the main bundle. Wrap ACT and MAF harness with tape.
#6 Coil
ACT Wire breakout point
1305SS-TVSIM-BA 20130911 Page 27 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
5.
Pull the 2-wire ETC (electronic throttle control) wiring loose from the main harness and drag it back to 20mm past the #8 coil break out point. Position the ETC connector so that the base of the connector is 165mm from the main bundle.
6.
Slide the driver side of the harness back into its convoluted tubing and re-tape. Wrap the ECT wiring with tape.
7.
Move the front (2) harness retainers on driver’s side coil harness from the bottom side to the top side of the harness leaving the rear retainer on the bottom side. Remove the harness to intake manifold stud clip and re-tape it to the harness 210mm from the left valve cover rear retainer.
8.
Locate the TPS (Throttle position sensor) connector and harness at the front of the passenger side. Remove the split loom convolute and tape from this harness until the main bundle.
9.
Stagger cut the 4 TPS wires 60, 90, 120 and 150mm from the TPS connector. Use the supplied
TPS extension harness (R07080031-13-AA) to lengthen the TPS wires using the same technique outlined in step #4. Cover the extend harness with the supplied convolute and run it along with the main harness, securing it to the main harness with tape every 150mm to a position 30mm before the rear intake manifold wire retainer.
New Location
(Step #4)
New Location
(Step #5)
New Location
(Steps #8-9)
New Orientation
On Top
(Step #7)
New Location
(Step #7)
Wiring Modification Summary
1305SS-TVSIM-BA 20130911 Page 28 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Fuel System Modification (This section only to be completed by Phase #2 Customers)
1.
Using the Ford Racing installation manual “M-9407-GT05” which is located at the end of this manual in Appendix A, install the Ford Racing GT500 Fuel System Upgrade Kit (R14020001).
These instructions can also be found on the internet at:
www.fordracingparts.com/download/instructionsheets/FordInstShtM-9407-GT05.pdf
2. Use (2) M6 nuts (W520412) to secure the new fuel pump driver module to an existing stud in the trunk as per the Ford installation manual.
Cylinder Head Modification
1.
Cut out the following template. Line up the template with the front of the right hand cylinder head.
Using a grinder with a sanding pad attachment, sand down the front corner of the cylinder head up to the template. Take special care that no shavings enter the engine cylinders. Thoroughly clean engine upon completion of this modification.
MODIFY HEAD
IN THIS AREA
TEMPLATE
BEFORE AFTER
1305SS-TVSIM-BA 20130911 Page 29 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
This page is intentionally left blank.
1305SS-TVSIM-BA 20130911 Page 30 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
SECTION C - SUBASSEMBLY
Induction System
1.
Install the stock MAF sensor using (2) M4 x 0.7 x 10 MAF bolts (R07130007) into the new clean air tube (R07060101). Torque bolts to 3
– 5Nm.
Clean air tube
MAF bolts
Factory
MAF
Sensor
2.
Install the clean air tube bracket (R07130010) on the clean air tube and position using the alignment marks on both the bracket and the tube. Secure the bracket to the tube using (1) M6 x
1.0 x 14 bolt (N605771) supplied in the kit. Apply medium strength thread locker to bolt threads prior to installation and torque to 8
– 12 Nm.
3.
Install the air filter (R07060131) to the clean air tube and align the metal strip on the air filter with the alignment mark on the clean air tube. Torque the worm drive clamp to 3 Nm.
1305SS-TVSIM-BA 20130911 Page 31 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
4.
Install rubber Grommet and Sleeve Assembly (R07130013) by first installing the rubber grommet into the Shelby Air Box Assembly (R07130039). Once the grommet is firmly seated in position, re-install the metal sleeve into the grommet.
Rubber grommet
Sleeve
5.
Assemble the air tube and filter onto the air box housing using (2) bolts (N605771) and torque to
8
– 12 Nm.
1305SS-TVSIM-BA 20130911 Page 32 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
S/C Pulley Install
1.
Install the S/C Pulley onto the Supercharger (P51AGH-6F066) using the six (6) N605771 bolts
(M6 x 14) provided. Ensure the pulley is properly seated on the hub before tightening any bolts.
Torque bolts to 8-12 Nm.
Fuel Rail Assembly
1.
Install the new injector clips (13109C995) onto the new Fuel Injectors (R07110007) from
Hardware Kit B. Apply assembly lube to the injector O-rings and install the injectors into the new
Fuel Rail (R07110006). Verify that the injector clips are properly seated and fully engaged into the fuel rail injector cups.
Fuel Charging
1.
Install the PCV Bubbler Hose (R07060175) onto the Fuel Charging Assembly (R07060135) and secure it using (1) of the supplied PCV Bubbler clamps.
R07060175
BUBBLER HOSE
R07060135
MANIFOLD ASY
FUEL CHARGING
1305SS-TVSIM-BA 20130911 Page 33 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
SECTION D - ASSEMBLY
The following section will guide you through the final installation of the kit into the vehicle. If you need to stop during any part of the installation, make sure you cover any open ports in the cylinder heads or intake manifold to prevent foreign material from contaminating your engine.
Intercooler Reservoir Mounting
1.
Using the Intercooler Degas Bottle (R07070007) with Degas Bottle Cap (XL3Z-8100-AA) as a template, place the bottle on the flat part of the electric fan shroud between the power steering reservoir and the engine coolant degas bottle. With the edge of the bottle at the edge of the electric fan shroud, mark the (2) mounting holes with a paint pen and drill two 5/16” holes through the fan shroud.
Mark and Drill here
1305SS-TVSIM-BA 20130911 Page 34 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
2.
Cut out the following template and use it to mark the third mounting hole and drill to 5/16”.
Mark and drill to 5/16”
3.
Clean the mating surfaces of the degas bottle and fan shroud with brake cleaner or rubbing alcohol. Peel and stick one side of the Double-Sided Tape (R07030002) provided in Cooling
System Hardware Kit, to the underside of the degas bottle.
Double-Sided Tape
1305SS-TVSIM-BA 20130911 Page 35 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
This page is intentionally left blank.
1305SS-TVSIM-BA 20130911 Page 36 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
4.
Remove the upper fan shroud bolts and force the shroud toward the rear of the vehicle. Install the (2) J-Clips (N623332) from the Hardware Kit. Peel the second side of the double-sided tape and set the bottle on the fan shroud. Secure the intercooler degas bottle using (2) M6 x
1.0 x 33 bolts (N808429) and the M6 x 1.0 x 8 cap screw (R18020010) with washer
(R18030002) from Hardware Kit and torque to 8
– 12Nm. Reinstall the upper fan shroud bolts and torque to 8
– 12Nm.
Intercooler Radiator Assembly Mounting
1.
Remove the (6) push pin retainers highlighted below by pulling the center pin and remove the radiator trim cover.
Push Pin retainers
1305SS-TVSIM-BA 20130911 Page 37 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
2.
Raise the vehicle and remove both front tires. Remove the (3) forward Phillips-head screws from each front wheel liner. Using a Phillips-head screwdriver, turn the (5) inner fender push pins ¼ turn to release the centers. Remove the pushpins and then remove the forward inner fenders.
Inner Fender Push Pin Locations
3 Phillips head screws
3.
Remove the (3) lower close-out to radiator support screws (7mm). Remove the (2) upper bumper cover screws near the headlights (10mm). Remove the (4) front fender to bumper cover nuts inside the forward wheel well (10mm).
Upper Bumper
Cover Screws
Close-out screws
Fender to Bumper
Cover Nuts
1305SS-TVSIM-BA 20130911 Page 38 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
4.
Reach inside the front wheel wells and unplug the front turn signals (there are four connectors total). Lift the front bumper cover slightly and pull partially off of the vehicle. Unplug the fog lights and set the front bumper cover aside.
5.
Remove the four push pins that retain the impact absorber to the front bumper beam and set the absorber aside.
Push Pins
6.
Remove the inner front bumper beam bolts. Save one bolt for reuse later.
Inner Bumper Bolts
1305SS-TVSIM-BA 20130911 Page 39 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
7.
Loosely install the (4) Long Bumper Bolts (R18020007) from the Hardware kit in place of the (4) which were just removed. Insert the Intercooler Radiator Assembly (R07070047) behind the bumper and between the frame rails aligning the holes in the bracket with the weld nuts for the inner bumper bolts. Snug the inner bumper bolts threading them through the bracket holes and torque to 20
– 30 Nm. Install the (4) LTR Mounting Nuts (W520413) from the Hardware Kit on the exposed end of the long bumper bolts and torque to 20
– 30 Nm.
Retaining Nut
Intercooler Radiator Assembly
Inner Bumper Bolt
8.
Reinstall the impact absorber onto the front bumper beam using the take out pushpins.
9.
Install the 12 ½” LTR Inlet Hose on the driver side of LTR with one ¾” Hose Clamp and leave hanging. Install the 33 ¾” LTR Outlet Hose on the passenger side of the LTR with one ¾”
Hose Clamp and route up through the fender and into the engine compartment as illustrated below.
1305SS-TVSIM-BA 20130911 Page 40 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Electric Water Pump Bracket Mounting
1.
Cut out the following template. Line up the template with the tie down bracket inside the driver side wheel well. Center punch the
“X”s marked on the template into the frame rail of the vehicle.
Drill two ¼” holes through the frame rail and de-burr the holes.
Cut this out and use as a template to locate holes
2.
Install (2) J-Clips (N623332) from Hardware Kit and mount the Intercooler Pump Mounting
Bracket (R07070015) using Bolts (N605891) onto the body. Torque bolts to 8
– 12Nm. Slide the
Intercooler Pump (F8YZ-8501-AA) into the bracket and secure using the bumper bolt removed earlier and a M8 Nut (W520413) from Hardware Kit. Torque the nut and bolt to 8
– 12Nm.
Use take off bumper bolt in this location
1305SS-TVSIM-BA 20130911 Page 41 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
This page is intentionally left blank.
1305SS-TVSIM-BA 20130911 Page 42 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
3.
Connect the
12 ½” LTR Inlet Hose (previously installed to LTR) to the outlet of the pump with a
¾” Hose Clamp. Install the 31” Degas Bottle Outlet Hose onto the pump inlet with a ¾” Hose
Clamp. Route the Degas Bottle Outlet Hose up through the fender to the Degas Bottle as illustrated. Connect this hose to the bott om outlet of the Degas bottle using one ¾” hose clamp.
Note: Route all intercooler hoses very carefully. It is critical to the intercooler
performance that these hoses are not kinked once installed into the vehicle.
Electric Water Pump Harness
1.
Disconnect the positive battery leads from the main positive battery cable at the fuse box.
Note: The bolt will remain retained by the cable’s terminal end.
2.
Locate the fuse holder branch of the Intercooler Pump Harness (R07080016). Run the short lead with the eyelet from the fuse holder to the Fuse box battery terminal.
1305SS-TVSIM-BA 20130911 Page 43 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
3.
Reinstall the battery cable bolt through the I/C fuse lead and the main battery cable. Torque the bolt to 8
– 12Nm.
4.
Secure the fuse holder to the strut tower using a M6 x 1.0 x 14 bolt (N605771) from Hardware kit threaded into the tapped hole in the strut tower across from the fuse box’s main battery terminal.
Torque bolt to 8
– 12 Nm.
5.
Route the remaining I/C pump harness with the vehicle harness around the driver side of the
PCM bracket to the space ahead of the PCM connectors.
6.
Locate the M6 bolt threads protruding from the core support into the engine compartment ahead of the PCM brackets. Slide the I/C pump relay’s bracket over this stud and secure with a M6 nut
(W520412). Torque the nut to 8
– 12Nm.
6mm Bolt threads
Front of Vehicle
1305SS-TVSIM-BA 20130911 Page 44 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
7.
Route the ground wire branch of the harness up to the ground screw directly above the relay.
Remove the ground screw and install the I/C Pump ground wire with all the factory grounds that were already in place with the bolt. Torque the bolt to 8
– 12Nm.
8.
Locate the square 16-pin connector on the driver side of the PCM bracket. Unplug the connector and remove the short section of convoluted tubing and electrical tape from the harness immediately behind the engine side (rearward half as mounted) of the connector. Locate the red w/yellow stripe wire in pin location #16. Cut this red wire about 1 inch back from the connector.
16-pin connector
Red/yellow stripe - #16
1305SS-TVSIM-BA 20130911 Page 45 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
9.
Seal the connector end of the red wire using one piece of heat shrink provided with the
Intercooler Pump Wiring Harness Kit (R07080016).
Sealing cut wire ends with Heat Shrink tubing
10.
Strip approximately 3/8” of insulation off the harness side of the red w/yellow wire. Place a piece of supplied heat shrink tubing over the remaining, non-terminated end of the Intercooler Pump
Wiring Harness. Strip approximately 3/8” of insulation off the end of the intercooler wire and connect to the red wire using the provided splice connector from the Intercooler Pump Wiring
Harness Kit and crimp using a W-type crimping tool. Using a clean, hot soldering iron, heat the wires (not the solder) in the splice connector until they are hot enough to melt the solder touched to them. Slide the heat shrink tubing over the solder joint and heat to shrink with a heat gun.
Reinstall the convoluted tubing and tape removed from the factory harness.
1305SS-TVSIM-BA 20130911 Page 46 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
11.
Plug the connector back together. Route the remainder of the Intercooler Pump Wiring Harness over the radiator (following the existing harness) behind the headlamp on the driver side and into the inner fender area where the water pump bracket is mounted. Remove the top water pump bracket mounting bolt and install the wiring harness ground eyelet and re-torque the fastener.
Connect the wiring harness to the electric water pump.
Ground the pump wiring harness to the body in this location.
1305SS-TVSIM-BA 20130911 Page 47 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Lower Radiator Hose Installation
1.
2005
– 06 VEHICLES ONLY – Install the Lower Radiator Hose (7R33-8B273-AA) by sliding the hose onto the outlet at the bottom corner of the radiator. Then push the hose on to the fitting on the oil filter adapter. Connect the smaller hose to the bottom of the degas bottle. Secure each point with the clamps that are glued onto the hose.
1305SS-TVSIM-BA 20130911 Page 48 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Engine Hardware and ROUSHCharger Installation
1.
Using the take off bolts, install the FEAD tensioner (R07020043). Torque bolts to 20
– 30 Nm.
2.
Remove the factory spark plugs and coils from the engine.
NOTE: Customers with 2005 - 07 vehicles and 2008 vehicles (with AA level engines only) use the supplied 14mm plugs (HTO-032). Customers with 2008 vehicles (with AB level engines) and customers with 2009 vehicles with 12mm plugs (Ford P/N: 8L3E-12405-BB) must gap their
factory spark plugs to 0.032 +/-
0.002”.
3.
Install either the newly supplied HTO-032 plugs (14mm plugs) or regapped (12mm plugs) depending on your engine configuration. Torque 14mm plugs to 30
– 38 Nm. Torque 12mm plugs to 10
– 15 Nm.
4.
Reinstall the coils and torque coil bolts to 4
– 6 Nm.
1305SS-TVSIM-BA 20130911 Page 49 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
5.
Install the modified heater tube assembly using the take out stud bolt. Be sure to lube the Orings with assembly lube before installing the heater tube to the water pump fitting in the block.
Torque the stud to 8
– 12 Nm.
6.
Carefully place the intake manifold assembly (with gaskets) down onto the cylinder heads. Be carefully not to damage your sealing surfaces or gaskets during this step. Take special care to ensure that the CHT wiring harness does not get pinched or trapped during manifold installation.
Insert (2) M6 x 1.0 x 40 bolts (R18020004) in holes A and B as shown and start threads by hand.
Do NOT tighten these fasteners. The intake must remain free to move along the cylinder head surfaces.
A
B
1305SS-TVSIM-BA 20130911 Page 50 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
7.
Install the Alternator Bracket (R07020035) onto the studs previously used to mount the alternator to the cylinder block and temporarily secure the bracket using the stock nuts. Use the FEAD bracket rear mounting bosses to properly align the intake manifold on the cylinder head surfaces by shifting the manifold from front to back and side to side. When you are finished, these features should be aligned in both the for-aft and side-to-side directions.
8.
Once aligned, fasten the intake manifold using (11) M6 x 1.0 x 40 supplied bolts (R18020004) and the stock driver side rear stud in hole #10 (used to retain the wiring harness). Tighten these fasteners in the sequence shown below and torque all to 8
– 12 Nm. Remove the alternator bracket from the engine as it will be installed in a later step.
11
7 3
1
5 9
12 8 4 2 6
10
(STUD)
1305SS-TVSIM-BA 20130911 Page 51 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
9.
Fasten the supercharger to the intake manifold using (8) M8 x 1.25 x 56 bolts (N808130) and (2)
M6 x 15 / M8 x 53 studs (R18040007) in holes #1 and #5. Torque fasteners in three steps;
10Nm, 20Nm and 30Nm in the sequence shown.
7 3 1 5 9
10
8 4 2 6
10.
Connect the PCV bubbler hose to the 90 deg fitting on the back of the supercharger using (1) of the supplied 3/8” constant tension clamps.
1305SS-TVSIM-BA 20130911 Page 52 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
11.
Re-install the FEAD bracket using (2) take off M8 nuts for mounting to old alternator studs, (2) M8 x 1.25 x 38 bolts (W705128) for fastening to the upper intake manifold and (1) M8 x 1.25 x 110 bolt (R18020058) with (1) spacer (R18030017) to fasten to the supercharger. First hand tighten every bolt, then torque the M8 nuts to 20
– 30 Nm, then torque the middle M8 bolts to 20 – 30
Nm, then finally torque the top M8 bolt to 20
– 30 Nm.
R18030017
Spacer
12.
Install the (2) FEAD Pulleys (R07020049) to the alternator bracket using the (2) M8x1.25x32 Idler
Bolts (R18020060). Torque bolts to 20
– 30Nm.
R18020060
(M8X1.25X28mm)
TORQUE 20-30 Nm
2 REQ’D
R07020049
76MM IDLER
1305SS-TVSIM-BA 20130911 Page 53 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
13.
Lubricate the fuel injector o-rings with 5W-20 engine oil. Apply a small amount of engine oil to the injector pockets in the intake manifold and install the fuel rail and injector assembly. Be sure each injector is properly seated into the intake manifold. Secure the fuel rail using (2) take out studs on the driver’s side and (2) M6 x 1.0 x 22mm bolts (R18020057) on the passenger side.
Torque bolts to 8
– 12 Nm.
14.
Install the 7/32” vacuum hose (R18140001) from the IPTS on the fuel rail to the fitting in the upper intake manifold.
R18140001
VACUUM HARNESS
1305SS-TVSIM-BA 20130911 Page 54 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Charge Harness and Wiring Installation
1.
2005
– 08 VEHICLES ONLY – Slide the smart charge harness (R07080033) underneath the front cover of the supercharger behind the FEAD bracket so that the round connector is on the passenger side of the engine. (2009 Vehicles
– please refer to Section E on Page 79)
2.
2005
– 08 VEHICLES ONLY – Connect the alternator smart charge harness by routing the harness as shown. (2009 Vehicles
– please refer to Section E on Page 79)
1305SS-TVSIM-BA 20130911 Page 55 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
3.
Connect injector #1
– 4 and coil #1 – 3.
4.
Move the main harness on top of coil #4 and plug in coil #4 around it.
5.
Pull the main harness below the rear intercooler turret.
1305SS-TVSIM-BA 20130911 Page 56 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
6.
Drape the TPS harness breakout in-between the driver side fuel rail and the supercharger.
7.
Install the rear harness retaining clip on the stud in the back of the intake manifold.
1305SS-TVSIM-BA 20130911 Page 57 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
8.
Push the two retaining clips onto the studs on the LH cam cover. Connect injectors #5
– 8 and coils #5
– 8.
9.
Route the ACT sensor under the fuel rail in-between injectors #6 and #7 and connect sensor.
1305SS-TVSIM-BA 20130911 Page 58 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
10.
Connect the IPTS.
11.
2005
– 08 VEHICLES ONLY – Route the B+ cable (R07080032) under the main harness inbetween the VCT solenoid and coil #5. (2009 Vehicles
– please refer to Section E on Page 79)
1305SS-TVSIM-BA 20130911 Page 59 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
12.
2005
– 08 VEHICLES ONLY – Push the B+ cable retainers onto the fuel rail studs. (2009
Vehicles
– please refer to Section E on Page 79)
13.
2005
– 08 VEHICLES ONLY – Remove the (2) plastic fasteners that hold the cowl grill in place.
Lift the cowl grill for easier access to replace the factory screw that secures the grounding strap to the cowl with (1) M6 x 1.0 x 18.5mm bolt (N605891) at the arrow shown. Torque bolt to 8
–
12Nm and replace plastic fasteners. (2009 Vehicles
– please refer to Section E on Page 79)
Insert new bolt here
Remove plastic fasteners
1305SS-TVSIM-BA 20130911 Page 60 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
14.
2005
– 08 VEHICLES ONLY – Route the B+ cable through the grounding strap and secure it to the dash using (1) Stud Mount Zip Tie (R18080003). Push the Zip Tie onto the M6 Bolt from the previous step then wrap the zip tie around the cable. (2009 Vehicles
– please refer to Section E
on Page 79)
15.
2005
– 08 VEHICLES ONLY – Secure the B+ cable to the dash by pushing the retainer
(Christmas tree) to the factory dash panel tab. (2009 Vehicles
– please refer to Section E on
Page 79)
1305SS-TVSIM-BA 20130911 Page 61 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
16.
Using the take off M8 nut, fasten the driver side radio suppressor to the driver side front cover stud. Before tightening, ensure there is sufficient clearance to all FEAD components. Torque to
23
– 27Nm. Use a screwdriver to bend the tab around the back of the stud.
17.
Using the take off M8 nut, fasten the passenger side radio suppressor to the passenger side front cover stud. Before tightening, ensure there is sufficient clearance to all FEAD components.
Torque nut to 23
– 27 Nm. Bend the tab around the back of the stud.
1305SS-TVSIM-BA 20130911 Page 62 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
18.
2005
– 08 VEHICLES ONLY - Insert (2) M8 x 1.25 x 55 bolts (N808130) and (2) M8 nuts
(W520413) through the alternator bracket. Be sure to leave enough room to insert the alternator.
Slide the alternator onto the bolts. Ensure that the smart charge harness does not get pinched.
Torque to 20
– 30 Nm. (2009 Vehicles – please refer to Section E on Page 79)
19.
2005
– 08 VEHICLES ONLY - Install the Rear Alternator Support Bracket (R07020045) using the
M8 x 1.25 x 20mm bolt (R18020005) into the alternator and M8 x 1.25 x 25mm bolt (W500224) into the intake. Route the B+ cable in-between this bracket and the alternator. Torque bolts to 20
– 30 Nm.
(2009 Vehicles
– please refer to Section E on Page 79)
WARNING: Do not put any bolt longer than 20mm into the back of the alternator.
Route B+ Cable under this bracket
W500224
R18020005
20mm MAX
Length
1305SS-TVSIM-BA 20130911 Page 63 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
20.
2005
– 08 VEHICLES ONLY – Connect the B+ cable to the stud on the back of the alternator using the take off nut. Torque to 8
– 12 Nm. Plug in the smart charge harness. Ensure that there are no pinched wires around the alternator.
(2009 Vehicles
– please refer to Section E on
Page 79)
21.
Install the FEAD belt as shown. Using a ½” drive breaker bar or ratchet, rotate the belt tensioner clockwise to install the supplied belt.
22.
Connect the rubber heater tube inlet hose (R07070067) to the steel heater water inlet tube
(R07070063) using (1) ¾” constant tension clamp. Install this assembly onto the engine by connecting the rubber hose to the 90 deg fitting on the intake using (1) constant tension clamp and fasten the steel tube to the supercharger studs using (2) M6 nuts (W520412).
1305SS-TVSIM-BA 20130911 Page 64 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
23.
Connect the fuel inlet line to the fuel rail and secure it using the safety clip.
24.
Install the throttle body spacer gasket (R07060152) and the throttle body gasket (R07060153) in the throttle body spacer (R07060147).
1305SS-TVSIM-BA 20130911 Page 65 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
25.
Fasten the throttle body spacer to the supercharger using (4) M6 x 1.0 x 32.5 screws
(R18020009) and torque to 8
– 12 Nm.
26.
Install throttle body onto the throttle body spacer using (4) M6 x 1.0 x 32.5 screws (R18020009).
Torque to 8
– 12 Nm.
1305SS-TVSIM-BA 20130911 Page 66 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
27.
Connect TPS and ETC.
28.
Install the PCV purge hose (R07050084) from the driver side cam cover to throttle body spacer.
1305SS-TVSIM-BA 20130911 Page 67 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
29.
Install the Intercooler Tube Assembly (R07070005) onto the passenger side cylinder head using the M16 x 40mm Tube Mounting Bolt (R18020006) for the rear and (1) M6 x 1.0 x 18 I/C Tube
Mounting Bolt (N605891). Torque the M16 bolt to 43
– 47Nm and the M6 bolt to 8 – 12Nm.
30.
Reconnect the stock
5/8” heater hose from the firewall to the modified heater tube located on the rear of the passenger side cylinder head using the original constant tension clamp.
31.
Install the ¾” x 190.9mm Intercooler Inlet hose (R07060173) from A to A using (2) ¾” constant tension clamps. Install the ¾” x 286.2mm Intercooler Outlet hose (R07060174) from B to B using (2) ¾” constant tension clamps.
B
B
A
A
1305SS-TVSIM-BA 20130911 Page 68 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
32.
Reconnect the stock 3/4” heater hose from the firewall by routing it under the intercooler hoses and connecting it to the steel heater inlet tube using the original constant tension clamp.
33.
Connect the LTR Outlet hose routed from behind the passenger side headlamp to the lower
Intercooler tube using (1) constant tension clamp. Install the 17 ½” Degas Inlet hose
(R07070006) from the upper intercooler tube, using (1) constant tension clamp #81-B, to the upper degas bottle fitting, using (1) ¾” worm clamp.
34.
Install the upper radiator hose (R07070022) using the take off constant tension clamps.
1305SS-TVSIM-BA 20130911 Page 69 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
35.
Locate the ABS module bracket and remove the bolt shown below.
ABS module
Remove bolt
36.
Install the rubber grommets from the bottom of the factory air box into the holes located beneath the air box, rearward of the ABS module.
Installed rubber grommets
1305SS-TVSIM-BA 20130911 Page 70 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
37.
Lower the air box assembly into the vehicle using the two pegs as guides into the rubber grommets. Loosely secure the air box to the vehicle using the take off air box bolt and the supplied ABS bracket bolt (N808920). Note: Do not torque bolts.
ABS bracket bolt
Take-off air box bolt
38.
Install the 3/16” (4440) and 3/8” (P2333A) fittings into their respective holes on the clean air tube
(1305-9B659). Foaming glass cleaner can be used to aid in this step. Place a vacuum cap over each of these fittings (383004 &CS2575), found in Hardware kit R07130040.
1305SS-TVSIM-BA 20130911 Page 71 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
39.
Loosely install the 120-140mm clamp (R07130014) onto the oval end of the clean air tube and the 110-130mm clamp onto the round end of the clean air tube (R07130015). Orient the clamps so both screw heads are facing the same direction of the PCV fitting. Install the clean air tube in the vehicle by first sliding the round end onto the MAF tube then pushing the oval end onto the throttle body. Tighten the throttle body clamp so the screw is close to the ETC motor on the topside of the throttle body. Tighten the MAF tube clamp so the screw is on the bottom side of the tube. Torque both clamps to 3 Nm.
40.
Tighten the (2) bolts in the air-box. Torque the M6 bolt to 8
– 12Nm and torque the M8 bolt to 22
– 26Nm.
41.
Check induction system to make sure everything is secured and at the required torque specification.
42.
Connect the MAF sensor.
1305SS-TVSIM-BA 20130911 Page 72 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
43.
Install the PCV Fresh Air tube (R07050083), by connecting the 90 deg fitting to the passenger side cam cover and running the tube over the supercharger and connecting the straight fitting to the rubber clean air tube.
1305SS-TVSIM-BA 20130911 Page 73 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Battery and Tray
1.
Install the battery tray by reversing the removal instructions. Torque the battery tray bolts to 8
–
12 Nm.
2.
Place the battery in the tray and secure with battery hold down. Torque the battery hold down bolt to 8
– 12 Nm. Reinstall the heat protecting battery wrap over the battery.
3.
Connect the B+ Alternator Harness to the positive battery terminal. Torque nut to 8
– 12Nm.
4.
Reinstall the battery connections by connecting the positive cable first then connecting the negative cable.
1305SS-TVSIM-BA 20130911 Page 74 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Vacuum System Connections
1.
Install the modified VMV hose such that the 90 deg. fitting is connected to throttle body spacer and the straight fitting is connected to the VMV’s upper port.
1305SS-TVSIM-BA 20130911 Page 75 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
2.
Connect the modified brake booster hose assembly onto the throttle body spacer.
3.
Connect the 7/32” vacuum hose from the T-fitting to the UPPER fitting on the supercharger bypass valve (this will be the fitting closest to the dash panel). The bottom/lower fitting MUST
remain open to atmosphere for the supercharger bypass system to function properly.
1305SS-TVSIM-BA 20130911 Page 76 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Coolant Fill and Final Assembly
1. Fill the engine cooling system (using a proper coolant mixture) to the marked level on the radiator degas bottle.
2. Using the same coolant mixture, fill the intercooler system. The coolant should be approximately one inch below the top of the cap.
Important:
Both coolant systems can trap a large amount of air. It is very important to verify that the air is purged and that coolant is flowing properly through both systems.
Roush recommends vacuum filling both systems to properly evacuate the trapped air.
3. Reinstall front bumper cover, lower close-out panel and inner fenders by reversing the removal procedures.
4. Reinstall the front wheels/tires. Torque wheel lugs to the factory Ford specifications.
5. Inspect all underhood wiring harnesses for potential interference issues. Use zip ties to safely position the harness away from any areas of concern.
6. If the PCM was removed and shipped to ROUSH for a ROUSH performed flash, reinstall it once the PCM is returned from ROUSH and apply PCM decal (R07100008). If you are equipped with a SAE J2534 pass through device, refer to the PCM Flashing section when installation is complete. DO NOT ATTEMPT TO REINSTALL THE PCM AND START THE VEHICLE IF
THE PCM IS NOT EQUIPPED WITH A ROUSH CALIBRATION. OPERATING THE ENGINE
WITHOUT THE RECALIBRATED PCM WILL RESULT IN ENGINE DAMAGE OR FAILURE
AND WILL VOID THE WARRANTY.
7. Reinstall the battery connections by connecting the positive cable first then connecting the negative cable.
8. The Belt Routing Diagram (13106E072) is to be placed on the underside of the hood, on the driver side, opposite of the factory Vehicle Emission Control Information decal.
Place Decal Here
1305SS-TVSIM-BA 20130911 Page 77 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
9.
The “Premium Fuel” clear decal with white lettering (R07110004) is to be installed on the instrument cluster bezel, on the flat area below the small center gauges.
Tachometer Speedometer
Place Decal Here
10.
The “Premium Fuel” white decal with black lettering (R07110003) is to be placed on the lower half of the inside of the fuel filler door.
Place Decal Here
11. If performing the PCM Flash procedure, proceed to
the “PCM Flashing” section. If the
PCM was sent to ROUSH for the Optional ROUSH Performed Flash and it has been
reinstalled, start the engine and check for unusual noise, dash service lights, and/or unusual operation. If problems are detected, immediately stop the engine or vehicle, diagnose and repair the problem.
1305SS-TVSIM-BA 20130911 Page 78 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
PCM FLASHING
1.
If equipped with a SAE J2534 pass through device, refer to the RDT-CALIM manual included in the CALKIT for PCM flashing. The RDT-CALIM manual will guide you through the ROUSH
Diagnostic Tool (RDT) software installation process and the ROUSH PCM flashing procedure.
OPERATING THE ENGINE WITHOUT THE RECALIBRATED PCM WILL RESULT IN
ENGINE DAMAGE OR FAILURE AND WILL VOID THE WARRANTY.
2.
Once the PCM has been successfully re-calibrated, start the engine and check for unusual noises, dash service lights, and unusual operation. If problems are detected, immediately stop the engine or vehicle, diagnose and repair the problem.
1305SS-TVSIM-BA 20130911 Page 79 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
SECTION E - 2009 VEHICLES ONLY
VERY IMPORTANT NOTE!
The following section of this manual is ONLY required for those customers with 2009 model year vehicles. Customers with 2005-08 vehicles should disregard this section.
________________________________________________________________________________________
REVISIONS TO “SECTION C–SUBASSEMBLY” (2009 Vehicles Only)
The following steps must be completed by 2009 VEHICLES ONLY.
1. Remove the (2) nuts shown from the back of the modified alternator
.
1305SS-TVSIM-BA 20130911 Page 80 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
2. Install (2) hex nuts (R07020053) in place of the (2) nuts removed in the previous step. Torque hex nuts to 5
– 7 Nm. BE CAREFUL NOT TO OVERTIGHTEN, which can cause the studs inside the alternator to break.
3. Secure the Rear Alternator Bracket (R07020056) to the rear of the alternator using (2) M5 x 0.8 x
10mm bolts (R18020059). Torque bolts to 5
– 7 Nm. BE CAREFUL NOT TO OVERTIGHTEN
THESE BOLTS.
1305SS-TVSIM-BA 20130911 Page 81 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
REVISIONS TO “SECTION D - INSTALLATION” (2009 Vehicles Only)
The following steps replace steps #1, #2, #11 - #15 and #18 - #20 of the Charge Harness and
Wiring Installation in SECTION D- INSTALLATION section of the 05-08 instruction manual.
1.
Push the Alternator Charge Harness (R07080034) retainers onto the driver side fuel rail studs as shown below.
2.
Insert (2) M8 x 55mm Bolts (N808130) and (2) M8 Nuts (W520413) through the alternator bracket. Be sure to leave enough room to insert the alternator. Loosely secure the alternator charge harness eyelet to the alternator using the take off M8 nut. Slide the alternator onto the bolts and route the charge harness under the rear alternator bracket (refer to picture in step #3 on next page). Torque M8 bolts to 25 Nm (18 lb-ft).
1305SS-TVSIM-BA 20130911 Page 82 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
3.
Secure the alternator to the intake using (1) M8x25mm Bolt (W500224). Torque to 20 Nm.
Torque the nut securing the charge harness to the alternator to 15
– 20 Nm. Plug in smart charge connector to alternator. Take special care to make sure the charge harness is not pinched anywhere.
Route charge harness under the bracket in this area
W500224
4.
Remove the (2) plastic fasteners that hold the cowl grill in place. Lift the cowl grill for easier access to replace the factory screw that secures the grounding strap to the cowl with (1) M6 x 1.0 x 18.5mm bolt (N605891) at the arrow shown. Torque bolt to 8
– 12Nm and replace plastic fasteners.
Insert new bolt here
Remove plastic fasteners
1305SS-TVSIM-BA 20130911 Page 83 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
5.
Route the alternator charge harness through the grounding strap and secure it to the dash using
(1) Stud Mount Zip Tie (R18080003). Push the Zip Tie onto the M6 Bolt from the previous step then wrap the zip tie around the cable.
6.
Secure the alternator charge harness to the dash by pushing the retainer (Christmas tree) to the factory dash panel tab.
1305SS-TVSIM-BA 20130911 Page 84 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
7.
Run the remaining smart charge section of the charge harness with the battery harness that runs along passenger side strut tower and secure it using the zip ties that have been pre-installed on the charge harness. Route wires under the main wiring harness bundle and plug into the connector.
Route wires along here
Route wires under main bundle
1305SS-TVSIM-BA 20130911 Page 85 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
Warranty
All retail parts carry a 90-day warranty from the date of purchase. This warranty covers defects in materials or workmanship, and does not include (i) normal wear and tear, environmental conditions, improper installation; (ii) road hazards, misuse, abuse, neglect, accidents, collision, fire, theft, freezing, vandalism, riot, explosion, or objects striking the vehicle; (iii) misusing the vehicle, such as driving over curbs, overloading, racing, or using the vehicle as a stationary power source; (iv) altering, disassembling or modifying the parts; (v) defects caused or induced by failures, breakdowns, or damage by other parts, components or the vehicle; (vi) subjecting the parts to excessive moisture or water or any motor vehicle fluids (e.g.: oil, anti-freeze, battery acid, brake fluid, etc.); (vii) acts of God, natural disasters and other similar causes beyond the reasonable control of ROUSH; or (viii) application of chemicals that affect the parts. This Limited
Warranty does not cover surface deterioration of paint, trim, and appearance items that result from use and/or exposure to the elements, such as stone chips, scratches, bird droppings, lightning, hail, windstorm, dings, dents, earthquake, road salt, tree sap, water or flood.
ROUSH SHALL NOT BE LIABLE TO REIMBURSE CUSTOMER/DEALER FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES RESULTING FROM THE INSTALLATION OR USE OF
ANY PRODUCT SOLD THROUGH THIS CATALOG OR ARISING OUT OF ANY BREACH OF
WARRANTY. EXCEPT AS MAY BE STATED IN THIS CATALOG, ROUSH DISCLAIMS ALL
EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL
ROUSH’S LIABILITY EXCEED THE PRICE PAID BY CUSTOMER/DEALER FOR PRODUCTS
SOLD REGARDLESS IF ROUSH HAS BEEN ADVISED IN ADVANCE OF ANY POTENTIAL
PROBLEM OR IF A CLAIM IS BASED ON CONTRACT, TORT, STRICT LIABILITY, PRODUCT
LIABILITY OR OTHERWISE. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF IMPLIED WARRANTIES OR THEIR DURATION, OR LIABILITY FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSIONS OR
LIMITATIONS MAY NOT APPLY.
This ROUSH Supercharger kit is designed and tested to function properly only on vehicles as they are equipped from the factory (completely stock powertrain). The use of aftermarket parts and equipment such as: cams, headers, nitrous oxide systems, other bolt-on performance parts, or any other performance parts not sold by, manufactured by, or approved of in writing by
ROUSH, will result in powertrain and supercharger kit damage and will not be the responsibility of ROUSH in any way.
1305SS-TVSIM-BA 20130911 Page 86 of 87 1-800-59-ROUSH
OFF ROAD USE ONLY – NOT FOR USE WITH POLLUTION CONTROLLED VEHICLES
APPENDIX A
FORD RACING MUSTANG GT DUAL FUEL PUMP KIT
INSTRUCTION SHEET
1305SS-TVSIM-BA 20130911 Page 87 of 87 1-800-59-ROUSH
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
Please contact the Techline for the most current instruction information (800) FORD788
! ! ! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION ! ! !
OVERVIEW:
The following information describes the procedure for the installation of the M-9407-GT05 dual fuel pump kit into
2005-07 Mustang GT.
! ! ! WARNING: DO NOT SMOKE OR CARRY LIGHTED TOBACCO OR OPEN FLAME OF ANY TYPE WHEN
WORKING ON OR NEAR ANY FUEL-RELATED COMPONENT. HIGHLY FLAMMABLE MIXTURES ARE
ALWAYS PRESENT AND MAY BE IGNITED, RESULTING IN POSSIBLE PERSONAL INJURY ! ! !
! ! ! WARNING: FUEL IN THE FUEL SYSTEM REMAINS UNDER HIGH PRESSURE EVEN WHEN THE ENGINE
IS NOT RUNNING. BEFORE SERVICING OR DISCONNECTING ANY OF THE FUEL LINES OR FUEL SYSTEM
COMPONENTS, THE FUEL SYSTEM PRESSURE MUST BE RELIEVED TO PREVENT ACCIDENTAL
SPRAYING OF FUEL, RESULTING IN PERSONAL INJURY OR A FIRE HAZARD ! ! !
! ! ! WARNING: DO NOT CARRY PERSONAL ELECTRONIC DEVICES SUCH AS CELL PHONES, PAGERS OR
AUDIO EQUIPMENT OF ANY TYPE WHEN WORKING ON OR NEAR ANY FUEL-RELATED COMPONENTS.
HIGHLY FLAMMABLE MIXTURES ARE ALWAYS PRESENT AND MAY BE IGNITED. FAILURE TO FOLLOW
THESE INSTRUCTIONS CAN RESULT IN PERSONAL INJURY ! ! !
! ! ! WARNING: THIS PROCEDURE INVOLVES FUEL HANDLING. BE PREPARED FOR SPILLAGE AT ALL
TIMES AND ALWAYS OBSERVE FUEL HANDLING PRECAUTIONS. FAILURE TO FOLLOW THESE
INSTRUCTIONS CAN RESULT IN PERSONAL INJURY ! ! !
! ! ! WARNING: FUEL LEVEL MUST BE AT ¾ OF A TANK OR LOWER OR FUEL SPILLAGE WILL OCCUR
WHEN FUEL MODULE IS REMOVED ! ! !
STEP 1: Release fuel system pressure.
1A: The fuel pump relay can be found in the bussed electrical center. The fuel pump relay is located in position 21 as shown in the inside cover of the bussed electrical center. Remove the fuel pump relay (see Fig. 1).
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
IS-1850-0129
Page 1 of 15
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
Fig. 1
1B: Start the engine and allow it to idle until it stalls. If engine does not start, proceed to STEP 1D.
1C: After the engine stalls, crank the engine for approximately 5 seconds to make sure the fuel
injection supply manifold pressure has been released.
1D: Turn the ignition switch to the OFF position.
! ! ! WARNING: BATTERIES NORMALLY PRODUCE EXPLOSIVE GASES. THEREFORE, DO NOT ALLOW
FLAMES, SPARKS OR LIGHTED SUBSTANCES TO COME NEAR THE BATTERY. WHEN CHARGING OR
WORKING NEAR A BATTERY, ALWAYS SHIELD YOUR FACE AND PROTECT YOUR EYES. ALWAYS
PROVIDE VENTILATION. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PERSONAL
! ! ! WARNING: KEEP OUT OF THE REACH OF CHILDREN. BATTERIES CONTAIN SULFURIC ACID. AVOID
CONTACT WITH SKIN, EYES OR CLOTHING. ALSO, SHIELD YOUR EYES WHEN WORKING NEAR THE
BATTERY TO PROTECT AGAINST POSSIBLE SPLASHING OF THE ACID SOLUTION. IN CASE OF ACID
CONTACT WITH THE SKIN OR EYES, FLUSH IMMEDIATELY WITH WATER FOR A MINIMUM OF 15 MINUTES
AND GET PROMPT MEDICAL ATTENTION. IF ACID IS SWALLOWED, CALL A PHYSICIAN IMMEDIATELY.
STEP 2:
INJURY ! ! !
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY ! ! !
Disconnect battery ground terminal (see Fig. 2).
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
IS-1850-0129
Page 2 of 15
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
Fig. 2
STEP 3: The fuel level in the tank should be ¾ of a tank or less before proceeding. If fuel exceeds more than
¾ of a tank, then follow STEPS 4-6. If fuel level is ¾ of a tank or less, then proceed to STEP 7.
STEP 4: Remove the fuel tank filler cap.
STEP 5: Insert a suitable drain hose into the fuel tank filler pipe until it reaches the fuel tank inlet tube.
CAUTION! The fuel pump and fuel level sensor will be below the fuel level in the tank when the tank is full. Make sure to drain ¼ of the fuel capacity through the filler pipe prior to removing the pumps or fuel spillage will occur.
STEP 6: Attach the fuel storage tanker to the fuel drain hose and remove as much fuel as possible from the fuel tank filler pipe. The fuel tank has a 16-gallon capacity. The removal of 4 gallons would lower the fuel level ¼ of a tank.
STEP 7: Remove the rear seat bottom and any insulation padding covering the fuel pump access cover.
7A: From under the front of the rear cushion assembly, push in the seat cushion release tab
located on the left and right of the seat, lift and remove the rear cushion assembly (see Fig. 3).
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
IS-1850-0129
Page 3 of 15
STEP 9:
STEP 8:
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
Fig. 3
Remove the fuel pump access cover (see Fig. 4).
Fig. 4
Disconnect the fuel pump electrical connector (see Fig. 5).
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
Page 4 of 15
IS-1850-0129
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
Fig. 5
CAUTION! If the liquid or vapor tube is damaged (torn, holes or delaminated), the effected tube assembly must be replaced with a new tube assembly. Do not use aftermarket sleeving. Do not readhere loose sleeving material.
CAUTION! When reusing liquid or vapor tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube. Apply clean engine oil to the end of the tube before inserting the tube into the connector.
CAUTION! Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is therefore essential that absolute cleanliness be observed when working with these components.
Always install blanking plugs to any open orifices or tubes.
STEP 10: Disconnect the fuel tube quick connect coupling on the fuel pump.
10A: Press the fuel tube quick connect coupling button and pull the fuel tube to disconnect (see Fig. 6).
Fig. 6
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
IS-1850-0129
Page 5 of 15
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
STEP 11:
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
Using a fuel tank lock ring wrench or a brass punch, remove the fuel pump retaining lock ring
(see Figs. 7-8).
Fig. 7 Fig. 8
CAUTION! The fuel pump must be handled carefully to avoid damage to the float arm, filter and convolute hoses.
STEP 12: Carefully lift the fuel pump out of the fuel tank enough to access and release the fuel cross-over tube quick connect coupling from the fuel pump (see Fig. 9).
Fig. 9
STEP 13: Completely remove the fuel pump from the fuel tank (see Fig. 10).
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
IS-1850-0129
Page 6 of 15
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
Fig. 10
CAUTION! Inspect the surfaces of the fuel pump mounting flange and fuel tank O-ring seal contact surfaces. Do not polish or adjust the O-ring seal contact area of the fuel tank flange or the fuel tank.
Install a new fuel tank if the O-ring seal contact area is bent, scratched or corroded.
CAUTION! Make sure to install a new fuel pump O-ring seal and lock ring.
STEP 14: To install, apply clean engine oil to the O-ring seal.
Install new fuel pump O-ring seal (see Fig. 11). STEP 15:
Fig. 11
STEP 16: Position the dual fuel pump into the fuel tank.
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
IS-1850-0129
Page 7 of 15
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
STEP 21:
STEP 17:
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
Connect the cross-over fuel tube quick connect coupling to the fuel pump.
CAUTION! Make sure the fuel tube clicks into place when installing the tube. To make sure that the fuel tube is fully seated, pull on the tube.
STEP 18: Make sure the alignment arrows on the dual fuel pump and the fuel tank meet before tightening the dual fuel pump lock ring. Using the special tool or brass punch, install the dual fuel pump with the new lock ring.
18A: Tighten the lock ring until it meets the stops on the fuel tank.
NOTE: The fuel pump is spring-loaded into the tank and may require slight pressure to install lock ring.
STEP 19: Connect the quick connect coupling on top of the dual fuel pump.
CAUTION! Make sure the fuel tube clicks into place when installing the tube. To make sure that the fuel tube is fully seated, pull on the tube.
STEP 20: Remove black cover from inside trunk to access fuel pump driver module (see Fig. 12).
Fig. 12
Disconnect fuel pump driver module located in spare tire well on driver side (see Fig. 13).
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
IS-1850-0129
Page 8 of 15
STEP 22:
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
Fig. 13
Mount additional fuel pump driver module in spare tire well on opposite side of existing fuel pump driver
(see Fig. 14).
Fig. 14
(see Fig. 15).
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
Page 9 of 15
IS-1850-0129
STEP 27:
STEP 28:
STEP 24:
STEP 25:
STEP 26:
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
Fig. 15
Connect connector labeled FPDM BODY SIDE CONNECTOR into the harness where the existing fuel pump driver module was connected.
Connect connector labeled FPDM NO. 1 to stock fuel pump driver module.
Mount wires labeled RELAY GROUND and FPDM NO. 1 GROUND in hole next to stock ground using ground screw (see Fig. 16).
Fig. 16
Connect connector labeled FPDM NO. 2 to newly mounted fuel pump driver module on passenger side.
Mount wire labeled FPDM NO. 2 GROUND to stock ground for audio amp on passenger side
(see Fig. 17).
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
Page 10 of 15
IS-1850-0129
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
Fig. 17
driver side of trunk, under rear seat and into rear seat area where the dual pump is located.
29A: For 2005 Mustang GT, a 1½” diameter hole will need to be cut out in the center of the access
cover for the fuel pump (see Fig. 18). Once hole is cut out, pull DUAL PUMP CONNECTOR and
SENDER CONNECTOR (1) through hole and seal hole with grommet. Unlock existing 4-pin female
connector on the harness previously connected into the stock fuel pump. Unlock the connector by
pulling the blue center piece forward (see Fig. 19). Proceed to STEP 29C.
Fig. 18 Fig. 19
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
IS-1850-0129
Page 11 of 15
STEP 33:
STEP 30:
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
29B: For 2006 Mustang GT and beyond, a second hole with a 1½” diameter will need to be cut into the
access cover. The hole should be ½” away from existing hole to allow clearance for the new
grommet to seal. Once the hole is cut out, pull DUAL PUMP CONNECTOR and SENDER
CONNECTOR (1) through hole and seal hole with grommet. Do not take the existing harness out
of the existing hole in the access cover. Unlock the existing 4-pin female connector (connector on
the end of the existing harness going through access cover) previously connected into the stock
fuel pump. Unlock the connector by pulling the blue center piece forward (see fig. 19).
29C: Release terminals for the LB/YE wire and the LG/VT wire from the connector housing. Do not
remove terminal from wire. These are the fuel sender wires.
Insert fuel sender wires into the connector labeled SENDER CONNECTOR (2) with the LB/YE wire going into the left side and the LG/VT wire going into the right (see Fig. 20).
Fig. 20
LG/VT wire should line up with the RD/YE wire and the LB/YE with the BK wire.
Install access cover (see Fig. 21 – 2005 Mustang GT view).
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
Page 12 of 15
IS-1850-0129
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
Fig. 21
along the wire track on the passenger side of the vehicle (see Figs. 22-24).
Fig. 22 Fig. 23
Fig. 24
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
Page 13 of 15
IS-1850-0129
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
34A: A hole will need to be placed in the grommet located in the lower area of the front wall on the
passenger side in order to run the wire through (see Fig. 25).
Fig. 25
STEP 35: Lift vehicle and remove the right front tire from vehicle along with the rear fender well cover. Continue to run wire along existing wire harness in fender well using wire ties to secure the wire along the existing wire harness (see Fig. 26).
Fig. 26
STEP 36: Remove innermost fastener on front fender well cover and continue to run wire into engine compartment.
The wire should come through the hole located near the washer fluid neck (see Figs. 27-28).
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
IS-1850-0129
Page 14 of 15
STEP 39:
STEP 40:
STEP 41:
STEP 42:
M-9407-GT05
Mustang GT Dual Fuel Pump Kit
INSTRUCTION SHEET
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF
FORD RACING PERFORMANCE PARTS
Fig. 27
Fig. 29
Reinstall relay in position 21 of bussed electrical center.
Connect negative terminal of battery.
Fig. 28
Check for leaks before starting the engine.
NOTE: It may take more than one key cycle to pressurize the fuel system. Cycle the ignition key and wait
3 seconds to pressurize the fuel system.
Start the engine and check for leaks.
Techline (800) FORD788
Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356
IS-1850-0129
Page 15 of 15
Dual Fuel Pump Kit
M-9407-GT05
Amendments
To avoid spilled fuel onto the carpet, to aid in the installation of the Wheel Hop Kit, to protect the power wire from abrasions, and to allow for a better seal on the grommet in the passenger foot well, please adhere to the fallowing amendments to the Ford Racing
Installation Instructions.
• Remove the fuel tank from the vehicle when changing the pump assemblies.
• Install the Wheel Hop Kit with the fuel tank removed.
• A depining tool can be made and used to pull the blue terminal locking device from the connector and to release the terminal from the connector. See below.
( Male terminal shown, female terminal similar. )
• Secure the excess wire in the trunk with wire ties.
• Cover the entire length of the red power wire with 1/4” convolute.
• Cut the fuse holder from the red wire. Cut the end off of the wire nipple and pass the red wire and convolute through the opening. Wrap with tape as shown to seal the grommet.
• At the fuse box, cut the excess red wire for best fit and reattach the fuse holder to the red wire using the same technique used on the engine harness for the TPS and
ACT wiring. Cover the wire with 1/4” convolute as shown.
• Secure the overlay harness to the vehicle main harness with wire ties placed every
10” to 12” and in the right front wheel well, every 6”.

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- single sheave
- premium fuel required
- PCM recalibration required
- off road use only
- detailed instructions
- step-by-step guide