PROGRAMMING THE TRANSMITTER STEP 1 - SET FREQUENCY SWITCH STEP 2 - SET BRAND JUMPERS
2b. The Model 39 contains 2 brand jumpers and 12 code
Thank you for your purchase of the Skylink garage door
remote control, Model 39. There are 3 different steps you
need to setup in order to use this universal garage door
remote conirol to operate your existing garage door
opener. These 3 steps are:
1) Frequency switch — select the correct frequency
according to the brand of your existing garage door
opener. Refer to Step 1.
2) Brand jumpers — place the brand jumpers at the
correct position according to the brand of your existing
garage door opener. Refer to Step 2.
3) Code setting — Set the jumper connectors on the Model
39 so that they match the code setting of your existing
garage door opener. Refer to Step 3 or Step 4
depending on the brand of your garage door opener.
Please follow the detailed instructions below in order to set-
up the Skylink Model 39 to work with your existing opener.
ta. Locate frequency
switch on the top of
the transmitter:
(See diagram A)
(See chart 1)
Diagram A
1b. Determine the brand of your garage
door opener and set the frequency
switch fo the corresponding position.
2a. To set the brand
jumpers, open the
case with a coin
(see diagram B).
Code connector Location
Jumper
Chart 1
STEP À - SET BRAND JUMPERS STEP 4 - SET CODE CONNECTORS
Diagram B A = #4 В = 5
REMOVE JUMPER = “0”
Diagram C
connectors (see diagram C). The brand jumpers are
located just above the battery with markings “A” and
“B”. There are 2 connectors, one is placed on the “A”
column, the other one is placed on the “B” column.
For each column, there is a connector. If ihe connector
is placed on the top and middle post of that column,
that column is set on “+”. If the connector is placed
on the middle and bottom posts, that column is set on
*“ If the connector is removed completely, that column
is set on “0” (see diagram C). In order for the Model
39 to work with your existing garage door opener
(motor), you need to set the brand jumpers based on
the brand of your existing garage door opener. Please
set these 2 brand jumpers “A” and “B” based on the
brand jumpers setting on chart 2. Please identify the
group number on chart 2 in order to determine which
is the next step to proceed.
Proceed to this step only if the brand of your garage door opener belongs to either group 4, 5, 6, 7 or 8 on chart 2. Otherwise, proceed to Step 3 -
connector. (see diagram F)
or receiver. There are 2 places you can find out the code setting from a column of small switches of
your existing garage door opener.
1) your existing transmitter (the unit you currently use to open your garage).
2) the receiver of your garage door opener (the unit with the motor mounted on the ceiling of
Group | Brand Brand jumpers setting | Proceed to Note:
A 8
+ [Chamberiain? , Sears®, Lift-Master? - + Learn code.
(without DIP switches but with red, orange or green
learn button) Proceed
2 |Chamberlain®, Lift-Master®, Sears®, Wayne Dalton®, 0 - to Step 3.
Master Mechanic® (without DIP switches but with
yellow, white, or gray learn button)
3* _|Genie® intellicode™* (without DIP switches) + +
4_{Genie® (with DIP switches), Overhead® 0 +
5 |Chamberiain®, Lift-Master®, Sears®, Wayne Dalton®, + - | Proceed
Master Mechanic® {with DIP switches) to Step 4,
6 {Stanley®, Multi-Code®, Martec® - - skip Step 3.
7 |Linear®, Moore-O-Matic® + 0
8 |Pulsar®, Allstar®, Allister®, Linear? MegaCode™ - 0 your garage).
* Note: Chart 2
For Genie? Intellicode™, if the brand jumper for group 3 cannot operate your garage door
opener properly, please use setting A “+”, В “-”.
STEP 4 - SET CODE CONNECTORS
Ac. If the connector is placed on the top and
middle posts, that column is set on * +”
or “ON” or “CLOSE”. If the connector is
placed on the middie and bottom posts,
‘ or ‘DEF’ or ‘OPEN’
‘+’ ar ‘ON’ or CLOSE
| ‘0’ = BLANK
$
that column is set on “ -” or “OFF” or
“OPEN”. If the connector is removed
completely, (not placed on any posts), it
is set to “0” or the neutral position. (see
diagram G for examples of how to set a
column to the three different positions).
When removing a connector to set a
+
о
| т. on
column to the neutral position, save
- the connector in case you change the
code at a later date.
If this transmitter triggers
other garage doors in
your neighborhood,
change all your trans-
mitters and receiver to a
new code setting.
DO NOT let children use
the garage door trans-
mitter without adult
supervision. Children
can injure themselves or
others by the garage
door.
BATTERY
12 volt alkaline battery
(size 23A) included.
FCC
The Universal Garage Door Remote
Contro! is approved by the FCC -
and it complies with Part 15 of the
FCC Rules. lts operation is subject
to the following two conditions :
1. This device may not cause
harmful interference.
2. This device must accept any
interference that may cause
undesired operation.
WARNING:
Changes or modifications to this unit
not expressly approved by the party
responsible of compliance could void
the user’s authority to operate the
equipment.
Ab. Set the connectors numbered 1 through 12 to match the code setting of your existing transmitter
4a. If the brand of your garage door opener belongs to groups 4 to 8, that means you need to program the correct code setting in order for the Model 39
to work with your existing garage door opener. There are 12 code connectors on 12 columns from 1 to 12 (see diagram E). Each column has one
o ah.
WEEE SEARS LL
Diagram E
Skylink will not be held
liable or responsible for
any misuse or application
of this product other than
for its intended use.
SKYLINK
TECHNOLOGIES INC.
2213 Dunwin Drive
Mississauga, Ontario,
ЕБЕ 1X1, CANADA
(905)608-9223
(905)608-8744 FAX
Email support skylinkh
(Reply within 24 hrs)
Customer Service : (800)304-1187
From Sam to 5pm EST (Mon-Fri)
http: /twww.skylinkhome.com
РАМ. 1014161-002 Rev.2
com
Patent no. 0377458, 5680134, 5841390,
6005508, 6249673B1
Patents Pending
©2002 SKYLINK TECHNOLOGIES INC.
6 are registered trademarks of their respactlva corporations
Diagram F
IN
SKY ®
LIK
GARAGE DOOR/GATE
REMOTE CONTROL
USER'S INSTRUCTIONS
(Mode! 39)
">
