PROGRAMMING THE TRANSMITTER STEP 1 - SET FREQUENCY SWITCH STEP 2 - SET BRAND JUMPER
. To set the brand
А open the
case with a coin
Thank you for your purchase of the Skylink garage door remote
ta. Locate frequency
1b. Determine the brand of your garage door
. control, Model 69. There are 3 different steps you need to set- switch on the top of opener and set the frequency switch to
up in order to use this universal garage door remote control to the transmitter: the corresponding position, (See chart 1)
(See diagram A)
operate your existing garage door opener. These 3 steps are:
1) Frequency switch — select the correct frequency according
to the brand of your existing garage door opener. Refer ta
Step 1.
2) alla according place the brand jumpers at the correct
sition according to the brand of your existing garage door
opener Refer to Step 2.
3) Code setting — Set the jumper connectors on the Model 69
so that they match the code setting of your existing garage
door opener.
Refer to Step 3 or Step 4 depending on the brand of your
Diagram A
garage door opener. |
^] вс] о}
Please follow the detailed instructions below in order to set-
up the Skylink Model 69 to work with your existing opener.
USA 39019181310] 300
¡CANADA [ 990] 318] 315] 310]
Chart 1
(see diagram В}.
Diagram C
2b. The Model 69 contains 2 brand jumpers and 12 code
connectors (see diagram C). The brand jumpers are
located just above the battery with markings "A" and
"В". There are 2 connectors, one is placed on the “A”
column, the other one is placed on the “В” column.
For each column, there is a connector. If the connector
is placed on the top and middie post of that column,
that column is set on "+". If the connector is placed
on the middle and bottom posts, that column is set on
=", if the connector is removed completely, that column
is set on “0° (see diagram С). In order for the Model
69 to work with your existing garage doar opener
(motor), you o he rend a o
“the brand of your garage door opener. Please
set these 2 brand jumpers “A” and "Br based on the
brand jumpers setting on chart 2. Please identify the
group number on chart 2 in order to determine which
is the next step to proceed.
12 wok alkaline battery (size ZA)
Proceed to this step only if the brand of your garage door opener belongs to
either group 4, 5, 6, 7 or 8 on chart 2. Otherwise, proceed to Step 3 - Learn code.
4a. if the brand of your garage door opener belongs to groups 4 to 8, that means
you need to program the correct code setting in order for the Mode! 69 to
work with your existing garage door opener. There are 12 code connectors on
12 columns from 1 to 12 (see diagram E). Each cofumn has one connector.
{see diagram F)
4b. Set the connectors numbered 1 through 12 to match the code setting of your
existing transmitter or receiver. There are 2 places you can find out the code
setting from a column of small switches of your existing garage door opener.
1) your existing transmitter (the unit you currently use to open your garage).
2) the receiver of your garage door
opener (the unit with the motor
Diagram F
ted on the ceiling of your SAS
garage).
Diagram E
ac. the connector is placed on the top and
middie posts, that column is set on “+”
or “ON” or “CLOSE”. К the connector is
placed on the middle and bottom posts,
that column is set on " -" or “OFF” or
"OPEN". If the connector is removed com-
‚ (not placed on any posts}, itis set
to * 0” or the neutral position. (see dia-
gram G for examples of how to set a
column to the three different positions).
When removing a connector to set a
cofumn to the neutral position, save
the connector in case you change the
code at a later date.
To operate the model 69 If this transmitter triggers
with your GDO properly, other garage doors in
please press the button your neigh ,
on the model 69. change all your trans-
mitters and receiver to a
new code setting
NOTE:
Transmission range may DO NOT let children use
be reduced with use on a the garage door trans-
metal garage door. mitter without adult
supervision. Children
can injure themselves or
others by the garage
door.
ren =
4 | Chambertain® , Sears®, Lit-Master® + -
(without DIP switches but with red, orange or green
Jean button) Procesd
2 |Chamberain®. Lif-Master?, Sears®, Wayne Сабо. - 6 to Step 3.
Master Mechanic? ¡without DIP switches but with
+ +
+ 0
_ + Proceed
to Step 4,
skip Step 3.
0 +
0 -
For Genio® intellicode**, if the brand jumper for group 3 cannot operate your garage door
opener properly, please use setting À "", В “+”.
FCC
The Universal Garage Door Remote
Control is approved by the FCC
and it complies with Part 15 of the
FCC Rules. Its operation is subject
to the following two conditions :
1. This device may not cause
harmful interference.
2. This device must accept any
interference that may cause
undesired operation.
WARNING:
Changes or modifications to this unit
not expressly approved by the party
responsible of compliance could void
the user's authority to operate the
equipment.
Skylink wal not be held
liable or responsible for
2213 Dunwia Drive
(Reply within 24 hrs)
ustomer Senaca : (9001304-1187
From Jam io 5pm EST (Mon-Fri}
http. fans. skylinkhome.com
PAN. 1014193-001 Rev.1
Palend
dar regir trademarks of their ceapacthre corporations
For garage door openers
belonging to groups cups À
For garage door openers
GARAGE DOORIGATE
REMOTE CONTROL
USER'S INSTRUCTIONS
(Model 69)
">
