Chamberlain 940EV, 940EVC Garage Door Opener User manual

Below you will find brief information for Garage Door Opener 940EV, Garage Door Opener 940EVC. The Chamberlain 940EV and 940EVC Wireless Keyless Entry provides a safe and convenient way to open and close your garage door. This device is compatible with Chamberlain 315 MHz or 390 MHz garage door openers manufactured after January 1, 1993. It features a 4-digit PIN code for security and can be configured with up to 255 unique temporary PINs for visitors. You can also program the device to open and close the door using just the ENTER button. The 940EV and 940EVC Wireless Keyless Entry has a one-year limited warranty.

PDF

Document

WIRELESS KEYLESS ENTRY • MODELS 940EV AND 940EVC

For use with Chamberlain 315 MHz or 390 MHz garage door openers manufactured after January 1, 1993. The garage door opener activates when the 4-digit Personal Identification Number

(PIN) and ENTER button are pressed on the Keyless Entry.

Install the battery and program the Keyless Entry prior to installation. Make sure the garage door opener has a working light bulb because it is a programming indicator.

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

• Install Keyless Entry Control within sight of the garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.

• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote controls.

• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

PREPARE

Learn

LED

Green or

Red/Orange

Locate the Learn button on the garage door opener.

NOTE: Your garage door opener may look different.

OR Learn

LED

Purple

Learn

LED

Yellow

PROGRAM INITIAL PIN

Press and hold buttons until the lights on the keypad stop blinking.

Press and

release the

Learn button.

The LED will light.

Within 30 seconds...

Enter a 4-digit personal identification number (PIN) of your choice:

? ? ? ?

Press and release the ENTER button...

Check to see if the light bulb blinks.

If not, slowly press and release the ENTER button until the light bulb blinks. Be careful NOT to

press the ENTER button after the

light bulb blinks.

Press 0 to complete the programming.

To test, press the PIN, then press the ENTER button.

? ? ? ?

To program the Keyless Entry to more than one garage door opener, repeat the steps above using a new PIN for each additional garage door opener.

CHANGE AN EXISTING PIN*

Press the programmed PIN that you want to change.

Press and hold the

# button until...

Enter the new 4-digit PIN of your choice, then press the ENTER button.

The garage door opener will activate.

To test, press the new PIN, then the ENTER button.

The garage door opener will activate.

? ? ? ?

new PIN

...the light bulb blinks twice.

* For garage door openers that have a green Learn button or an external receiver repeat "Program Initial PIN" to change the existing PIN.

The light bulb will blink once.

PROGRAM A TEMPORARY PIN

NOTE: This feature is not available on garage door openers that have a green Learn button or an external receiver.

A temporary 4-digit PIN can be programmed to allow access to visitors. Each programmed PIN can program one temporary

PIN. The temporary PIN can be set for a number of hours or a number of door openings. The temporary PIN cannot be the same as any previously programmed PIN.

Press any programmed PIN, then press and hold the * button until...

? ? ? ?

Enter the temporary 4-digit PIN of your choice, then press the ENTER button.

? ? ? ?

Temporary PIN

...the light bulb blinks 3 times.

The light bulb will blink

4 times.

3 NUMBER OF HOURS

Press the number of hours the temporary PIN will work (up to 255).

+ Then press

Press the number of openings the temporary PIN will work (up to 255).

NUMBER OF OPENINGS

Then press the # button.

1 blink

To clear the temporary PIN, repeat steps 1-3 above, setting the number of hours or openings to 0 in step 3.

INSTALLATION OPERATION

Select a location to mount the Keyless Entry at a minimum height of 5 feet (1.5 m) out of the reach of children.

Remove battery cover and battery.

Mark the top mounting hole and drill 1/8 inch (3.2 mm) pilot hole.

Install the top screw, allowing 1/8 inch (3.2 mm) to protrude above the surface. Position the Keyless Entry over the top screw.

The garage door opener activates when the PIN and ENTER button are pressed. The keypad will blink for 15 seconds, during that time the ENTER button can be used to stop, start or reverse the door.

If the wrong number is accidentally pressed, press the correct

PIN then the ENTER button. The Keyless Entry will transmit only the last four digits that were pressed before the ENTER button.

ONE BUTTON CLOSE: The Keyless Entry has a feature that allows the door to be closed using the ENTER button instead of a PIN.

5 Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot hole. Install the bottom screw. Do not overtighten to avoid cracking the plastic housing.

NOTE: This feature is not available on garage door openers manufactured prior to 2006 or an external receiver.

6 Reinstall battery and replace cover.

To deactivate the one button close feature:

Press and hold the 1 and 9 buttons for 10 seconds.

2 The keypad will blink four times when the one button close feature is deactivated.

To activate the one button close feature:

Press and hold the 1 and 9 buttons for 10 seconds.

2 The keypad will blink twice when the one button close feature is activated.

1-800-528-9131

114A3926

REPLACEMENT PARTS

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10A25

Keypad Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41D621

Battery Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41D541

BATTERY

1 blink

To test, press the temporary

PIN, then press the ENTER button. The garage door opener will activate. If the temporary

PIN was set for a number of openings, the test will use up one opening.

WARNING

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

Replace the battery when the keypad becomes dim or does not light after a button is pressed.

Dispose of old battery properly.

9V Battery

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER

SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARRANTY

ONE YEAR LIMITED WARRANTY

The Chamberlain Group, Inc. warrants to the first retail purchaser of this product that is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase.

www.chamberlain-diy.com

Hello! I am an AI chatbot specifically trained to assist you with the Chamberlain 940EVC User manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

Wireless control
Programmable PIN
Temporary PIN
One Button Close feature
Easy Installation
Easy to Program

Frequently asked questions

To program a temporary PIN, press any programmed PIN, then press and hold the * button until the light bulb blinks 3 times. Enter the temporary PIN, then press the ENTER button. The light bulb will blink 4 times. You can then set the temporary PIN for a number of hours or a number of door openings.

To change an existing PIN, press the programmed PIN that you want to change, then press and hold the # button until the light bulb blinks twice. Enter the new 4-digit PIN, then press the ENTER button. The light bulb will blink once. To test, press the new PIN, then press the ENTER button. The garage door opener will activate.

To deactivate the one button close feature, press and hold the 1 and 9 buttons for 10 seconds. The keypad will blink four times when the one button close feature is deactivated. To activate the one button close feature, press and hold the 1 and 9 buttons for 10 seconds. The keypad will blink twice when the one button close feature is activated.

Select a location to mount the Keyless Entry at a minimum height of 5 feet (1.5 m) out of the reach of children.
Remove battery cover and battery.
Mark the top mounting hole and drill 1/8 inch (3.2 mm) pilot hole.
Install the top screw, allowing 1/8 inch (3.2 mm) to protrude above the surface. Position the Keyless Entry over the top screw.
Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot hole. Install the bottom screw. Do not overtighten to avoid cracking the plastic housing.
Reinstall battery and replace cover.

User questions

Robert K.

What is the difference between the 940EV and 940EVC models?

The document does not specify the difference between the 940EV and 940EVC models. Both are mentioned as 'WIRELESS KEYLESS ENTRY,' suggesting they share the same basic functionality for use with Chamberlain garage door openers.