Cisco Systems LDK102054 802.11a/b/g Access Point User Manual

Add to my manuals
124 Pages

advertisement

Cisco Systems LDK102054 802.11a/b/g Access Point User Manual | Manualzz

C I S C O C O N F I D E N T I A L - D r a f t 1

Cisco Aironet 1130AG Series Access Point

Hardware Installation Guide

September 2004

Corporate Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA http://www.cisco.com

800 553-NETS (6387)

Customer Order Number:

Text Part Number: OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

• Turn the television or radio antenna until the interference stops.

• Move the equipment to one side or the other of the television or radio.

• Move the equipment farther away from the television or radio.

• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCSP, the Cisco Square Bridge logo, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live,

Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco

Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation,

Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness

Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet , PIX, Post-Routing, Pre-Routing, ProConnect,

RateMUX, Registrar, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0406R)

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

Copyright © 2004 Cisco Systems, Inc. All rights reserved.

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

C O N T E N T S

Preface

ix

Audience

ix

Purpose

ix

Organization

ix

Conventions

x

Related Publications

xii

Obtaining Documentation

xii

Cisco.com

xii

Documentation CD-ROM

xiii

Ordering Documentation

xiii

Documentation Feedback

xiii

Obtaining Technical Assistance

xiv

Cisco.com

xiv

Technical Assistance Center

xiv

Locating the Product Serial Number

xv

Cisco TAC Website

xv

Cisco TAC Escalation Center

xvi

Obtaining Additional Publications and Information

xvi

Overview

1-1

Hardware Features

1-2

Dual-Radio Operation

1-2

Ethernet Port

1-2

Console Port

1-2

LEDs

1-3

Power Sources

1-3

Anti-Theft Features

1-4

Network Configuration Examples

1-6

Root Unit on a Wired LAN

1-6

Repeater Unit that Extends Wireless Range

1-7

Central Unit in an All-Wireless Network

1-8

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide iii

Contents

C I S C O C O N F I D E N T I A L - D r a f t 1

Installing the Access Point

2-1

Safety Information

2-2

FCC Safety Compliance Statement

2-2

General Safety Guidelines

2-2

Warnings

2-2

Unpacking the Access Point

2-3

Package Contents

2-3

Basic Installation Guidelines

2-3

Before Beginning the Installation

2-4

Access Point Layout and Connectors

2-4

Mounting Plate

2-5

Suspended Ceiling Adjustable T-Rail Clips

2-6

Installation Summary

2-7

Opening the Access Point Cover

2-8

Mounting the Access Point

2-9

Mounting on a Horizontal or Vertical Surface

2-10

Mounting Below a Suspended Ceiling

2-11

Mounting on a Network Cable Box

2-12

Mounting on a Desktop or Shelf

2-12

Attaching the Access Point to the Mounting Plate

2-13

Connecting the Ethernet and Power Cables

2-14

Connecting to an Ethernet Network with an Inline Power Source

2-15

Connecting to an Ethernet Network with Local Power

2-16

Securing the Access Point

2-16

Using a Security Cable

2-16

Securing the Access Point to the Mounting Plate

2-17

Powering Up the Access Point

2-18

Configuring the Access Point for the First Time

3-1

Before You Start

3-2

Resetting the Access Point to Default Settings

3-2

Using the Mode Button

3-2

Using the Web-Browser Interface

3-2

Obtaining and Assigning an IP Address

3-3

Connecting to the Access Point Locally

3-3 iv

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

OL-6226-01

Contents

C I S C O C O N F I D E N T I A L - D r a f t 1

Assigning Basic Settings

3-4

Default Settings on the Express Setup Page

3-8

Protecting Your Wireless LAN

3-8

Using the IP Setup Utility

3-9

Obtaining and Installing IPSU

3-9

Using IPSU to Find the Access Point’s IP Address

3-10

Using IPSU to Set the Access Point’s IP Address and SSID

3-11

Assigning an IP Address Using the CLI

3-12

Using a Telnet Session to Access the CLI

3-12

Using the Web-Browser Interface

4-1

Using the Web-Browser Interface for the First Time

4-2

Using the Management Pages in the Web-Browser Interface

4-2

Using Action Buttons

4-4

Character Restrictions in Entry Fields

4-5

Using Online Help

4-5

Using the Command-Line Interface

5-1

IOS Command Modes

5-2

Getting Help

5-3

Abbreviating Commands

5-3

Using no and default Forms of Commands

5-3

Understanding CLI Messages

5-4

Using Command History

5-4

Changing the Command History Buffer Size

5-4

Recalling Commands

5-5

Disabling the Command History Feature

5-5

Using Editing Features

5-5

Enabling and Disabling Editing Features

5-6

Editing Commands Through Keystrokes

5-6

Editing Command Lines that Wrap

5-7

Searching and Filtering Output of show and more Commands

5-8

Accessing the CLI

5-8

Opening the CLI with Telnet

5-8

Opening the CLI with Secure Shell

5-9

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide v

Contents

C I S C O C O N F I D E N T I A L - D r a f t 1

Troubleshooting

6-1

Checking the Access Point LEDs

6-2

Checking Basic Settings

6-4

SSID

6-4

WEP Keys

6-4

Security Settings

6-4

Resetting to the Default Configuration

6-5

Using the MODE Button

6-5

Using the Web Browser Interface

6-6

Reloading the Access Point Image

6-7

Using the MODE button

6-7

Web Browser Interface

6-8

Browser HTTP Interface

6-8

Browser TFTP Interface

6-8

Obtaining the Access Point Image File

6-9

Obtaining the TFTP Server Software

6-9

Translated Safety Warnings

A-1

Statement 10—Installation Warning

A-2

Statement 13—Circuit Breaker (15A) Warning

A-3

Statement 245B—Explosive Device Proximity Warning

A-4

Statement 332—Antenna Installation Warning

A-5

Statement 1001—Work During Lightning Activity

A-6

Declarations of Conformity and Regulatory Information

B-1

Manufacturers Federal Communication Commission Declaration of Conformity Statement

B-2

Department of Communications—Canada

B-3

Canadian Compliance Statement

B-3

European Community, Switzerland, Norway, Iceland, and Liechtenstein

B-3

Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC

B-3

Declaration of Conformity for RF Exposure

B-5

Guidelines for Operating Cisco Aironet Access Points in Japan

B-6

Japanese Translation

B-6

English Translation

B-6

Declaration of Conformity Statements

B-7

Declaration of Conformity Statements for European Union Countries - TBD

B-7 vi

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

G

L O S S A R Y

I

N D E X

C I S C O C O N F I D E N T I A L - D r a f t 1

Access Point Specifications - TBD

C-1

Channels and Power Levels

D-1

Channels and Maximum Power Levels

D-2

IEEE 802.11b/g (2.4-GHz Band)

D-2

IEEE 802.11a (5-GHz Band)

D-3

Console Cable Pinouts

E-1

Overview

E-2

Console Port Signals and Pinouts

E-2

Contents

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide vii

Contents

C I S C O C O N F I D E N T I A L - D r a f t 1 viii

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

Preface

Audience

This guide is for the networking professional who installs and manages the Cisco Aironet 1130AG Series

Access Point, hereafter referred to as the access point . To use this guide, you should have experience working with the Cisco IOS software and be familiar with the concepts and terminology of wireless local area networks.

Purpose

This guide provides the information you need to install and configure basic settings for your access point. For information on using Cisco IOS commands to configure your access point, refer to the Cisco

IOS Software Configuration Guide for Cisco Aironet Access Points. For detailed information about these

IOS commands, refer to the Cisco IOS Command Reference for Cisco Aironet Access Points and Bridges for this release. For information about the standard IOS Release 12.2 commands, refer to the IOS documentation set available from the Cisco.com home page at Service and Support > Technical

Documents . On the Cisco Product Documentation home page, select Release 12.2

from the Cisco IOS

Software drop-down menu.

This guide also includes an overview of the access point web-based interface (APWI), which contains all the functionary of the command-line interface (CLI). This guide does not provide field-level descriptions of the APWI windows nor does it provide the procedures for configuring the access point from the APWI. For all APWI window descriptions and procedures, refer to the access point online help, which is available from the Help buttons on the APWI pages.

Organization

This guide is organized into these chapters:

Chapter 1, “Overview,”

lists the software and hardware features of the access point and describes the access point’s role in your network.

Chapter 2, “Installing the Access Point,” describes how to mount the access point on a desktop, wall, or

ceiling, how to connect Ethernet, serial, and power cables, and provides an installation summary, safety warnings, and general guidelines.

Chapter 3, “Configuring the Access Point for the First Time,” describes how to configure basic settings

on a new access point.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide ix

Conventions

Preface

C I S C O C O N F I D E N T I A L - D r a f t 1

Chapter 4, “Using the Web-Browser Interface,”

describes how to use the web-browser interface to configure the access point.

Chapter 5, “Using the Command-Line Interface,” describes how to use the command-line interface

(CLI) to configure the access point.

Chapter 6, “Troubleshooting,” provides troubleshooting procedures for basic problems with the access

point.

Appendix A, “Translated Safety Warnings,” provides translations of the safety warnings that appear in

this publication.

Appendix B, “Declarations of Conformity and Regulatory Information,” provides declarations of

conformity and regulatory information for the access point.

Appendix C, “Access Point Specifications,”

lists technical specifications for the access point.

Appendix D, “Channels and Power Levels,” lists the access point radio channels and the maximum

power levels supported by the world’s regulatory domains.

Appendix E, “Console Cable Pinouts,”

identifies the pinouts for the serial console cable that connects to the access point’s serial console port.

Conventions

This publication uses these conventions to convey instructions and information:

Command descriptions use these conventions:

Commands and keywords are in boldface text.

Arguments for which you supply values are in italic.

Square brackets ([ ]) mean optional elements.

Braces ({ }) group required choices, and vertical bars ( | ) separate the alternative elements.

• Braces and vertical bars within square brackets ([{ | }]) mean a required choice within an optional element.

Interactive examples use these conventions:

Terminal sessions and system displays are in screen font.

Information you enter is in boldface screen font.

• Nonprinting characters, such as passwords or tabs, are in angle brackets (< >).

Notes, cautions, and timesavers use these conventions and symbols:

Tip Means the following will help you solve a problem. The tips information might not be troubleshooting or even an action, but could be useful information.

Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.

x

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Preface

Conventions

C I S C O C O N F I D E N T I A L - D r a f t 1

Caution Means reader be careful. In this situation, you might do something that could result equipment damage or loss of data.

Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. (To see translations of the warnings that appear in this publication, refer to the appendix “Translated Safety Warnings.”)

Waarschuwing

Varoitus

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico’s en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. (Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het aanhangsel “Translated Safety Warnings” (Vertalingen van veiligheidsvoorschriften) raadplegen.)

Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. (Tässä julkaisussa esiintyvien varoitusten käännökset löydät liitteestä "Translated Safety Warnings" (käännetyt turvallisuutta koskevat varoitukset).)

Attention

Warnung

Avvertenza

Ce symbole d’avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures. Avant d’accéder à cet équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les procédures courantes de prévention des accidents. Pour obtenir les traductions des mises en garde figurant dans cette publication, veuillez consulter l’annexe intitulée « Translated Safety Warnings » (Traduction des avis de sécurité).

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer

Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur

Vermeidung von Unfällen bewußt. (Übersetzungen der in dieser Veröffentlichung enthaltenen

Warnhinweise finden Sie im Anhang mit dem Titel “Translated Safety Warnings” (Übersetzung der

Warnhinweise).)

Questo simbolo di avvertenza indica un pericolo. Si è in una situazione che può causare infortuni.

Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti. La traduzione delle avvertenze riportate in questa pubblicazione si trova nell’appendice, “Translated Safety

Warnings” (Traduzione delle avvertenze di sicurezza).

Advarsel Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til personskade. Før du utfører arbeid på utstyr, må du være oppmerksom på de faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker. (Hvis du vil se oversettelser av de advarslene som finnes i denne publikasjonen, kan du se i vedlegget "Translated

Safety Warnings" [Oversatte sikkerhetsadvarsler].)

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide xi

Preface

Related Publications

C I S C O C O N F I D E N T I A L - D r a f t 1

Aviso

¡Advertencia!

Varning!

Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos fisicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes. (Para ver as traduções dos avisos que constam desta publicação, consulte o apêndice “Translated Safety Warnings” - “Traduções dos Avisos de Segurança”).

Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes. (Para ver traducciones de las advertencias que aparecen en esta publicación, consultar el apéndice titulado “Translated Safety Warnings.”)

Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada.

Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador. (Se förklaringar av de varningar som förekommer i denna publikation i appendix "Translated Safety Warnings" [Översatta säkerhetsvarningar].)

Related Publications

These documents provide complete information about the access point:

Release Notes for Cisco Aironet 1130AG Series Access Point

Cisco IOS Command Reference for Cisco Aironet Access Points and Bridges

• Cisco IOS Software Configuration Guide for Cisco Aironet Access Points

Click this link to browse to the Cisco Aironet documentation home page: http://www.cisco.com/univercd/cc/td/doc/product/wireless/index.htm

To browse to the 1200 series access point documentation, select Aironet 1200 Series Wireless LAN

Products > Cisco Aironet 1200 Series Access Points .

Obtaining Documentation

Cisco provides several ways to obtain documentation, technical assistance, and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation on the World Wide Web at this URL: http://www.cisco.com/univercd/home/home.htm

You can access the Cisco website at this URL: http://www.cisco.com

International Cisco websites can be accessed from this URL: http://www.cisco.com/public/countries_languages.shtml

xii

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Preface

Obtaining Documentation

C I S C O C O N F I D E N T I A L - D r a f t 1

Documentation CD-ROM

Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which may have shipped with your product. The Documentation CD-ROM is updated regularly and may be more current than printed documentation. The CD-ROM package is available as a single unit or through an annual or quarterly subscription.

Registered Cisco.com users can order a single Documentation CD-ROM (product number

DOC-CONDOCCD=) through the Cisco Ordering tool: http://www.cisco.com/en/US/partner/ordering/ordering_place_order_ordering_tool_launch.html

All users can order monthly or quarterly subscriptions through the online Subscription Store: http://www.cisco.com/go/subscription

Ordering Documentation

You can find instructions for ordering documentation at this URL: http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

You can order Cisco documentation in these ways:

• Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Networking Products MarketPlace: http://www.cisco.com/en/US/partner/ordering/index.shtml

• Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, U.S.A.) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).

Documentation Feedback

You can submit comments electronically on Cisco.com. On the Cisco Documentation home page, click

Feedback at the top of the page.

You can e-mail your comments to [email protected].

You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:

Cisco Systems

Attn: Customer Document Ordering

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide xiii

Preface

Obtaining Technical Assistance

C I S C O C O N F I D E N T I A L - D r a f t 1

Obtaining Technical Assistance

Cisco provides Cisco.com, which includes the Cisco Technical Assistance Center (TAC) website, as a starting point for all technical assistance. Customers and partners can obtain online documentation, troubleshooting tips, and sample configurations from the Cisco TAC website. Cisco.com registered users have complete access to the technical support resources on the Cisco TAC website, including TAC tools and utilities.

Cisco.com

Cisco.com offers a suite of interactive, networked services that let you access Cisco information, networking solutions, services, programs, and resources at any time, from anywhere in the world.

Cisco.com provides a broad range of features and services to help you with these tasks:

• Streamline business processes and improve productivity

Resolve technical issues with online support

Download and test software packages

Order Cisco learning materials and merchandise

Register for online skill assessment, training, and certification programs

To obtain customized information and service, you can self-register on Cisco.com at this URL: http://tools.cisco.com/RPF/register/register.do

Technical Assistance Center

The Cisco TAC is available to all customers who need technical assistance with a Cisco product, technology, or solution. Two types of support are available: the Cisco TAC website and the Cisco TAC

Escalation Center. The type of support that you choose depends on the priority of the problem and the conditions stated in service contracts, when applicable.

We categorize Cisco TAC inquiries according to urgency:

Priority level 4 (P4)—You need information or assistance concerning Cisco product capabilities, product installation, or basic product configuration. There is little or no impact to your business operations.

Priority level 3 (P3)—Operational performance of the network is impaired, but most business operations remain functional. You and Cisco are willing to commit resources during normal business hours to restore service to satisfactory levels.

Priority level 2 (P2)—Operation of an existing network is severely degraded, or significant aspects of your business operations are negatively impacted by inadequate performance of Cisco products.

You and Cisco will commit full-time resources during normal business hours to resolve the situation.

Priority level 1 (P1)—An existing network is “down,” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.

xiv

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Preface

Obtaining Technical Assistance

C I S C O C O N F I D E N T I A L - D r a f t 1

Locating the Product Serial Number

The access point serial number is located on the bottom of the cabinet (refer to

Figure 1

).

Figure 1 Location of Serial Number Label - TBD

The access point serial number label contains the following information:

Model number, such as AIR-AP1310

Serial number, such as S/N: VDF0636XXXX (11 alphanumeric digits)

MAC address, such as MAC: 00abc65094f3 (12 hexadecimal digits)

Location of manufacture, such as Made in Singapore

You need your product serial number when requesting support from the Cisco Technical Assistance

Center.

Cisco TAC Website

The Cisco TAC website provides online documents and tools to help troubleshoot and resolve technical issues with Cisco products and technologies. To access the Cisco TAC website, go to this URL: http://www.cisco.com/tac

All customers, partners, and resellers who have a valid Cisco service contract have complete access to the technical support resources on the Cisco TAC website. Some services on the Cisco TAC website require a Cisco.com login ID and password. If you have a valid service contract but do not have a login

ID or password, go to this URL to register: http://tools.cisco.com/RPF/register/register.do

If you are a Cisco.com registered user, and you cannot resolve your technical issues by using the Cisco

TAC website, you can open a case online at this URL: http://www.cisco.com/tac/caseopen

If you have Internet access, we recommend that you open P3 and P4 cases online so that you can fully describe the situation and attach any necessary files.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide xv

Preface

Obtaining Additional Publications and Information

C I S C O C O N F I D E N T I A L - D r a f t 1

Cisco TAC Escalation Center

The Cisco TAC Escalation Center addresses priority level 1 or priority level 2 issues. These classifications are assigned when severe network degradation significantly impacts business operations.

When you contact the TAC Escalation Center with a P1 or P2 problem, a Cisco TAC engineer automatically opens a case.

To obtain a directory of toll-free Cisco TAC telephone numbers for your country, go to this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

Before calling, please check with your network operations center to determine the Cisco support services to which your company is entitled: for example, SMARTnet, SMARTnet Onsite, or Network Supported

Accounts (NSA). When you call the center, please have available your service agreement number and your product serial number.

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online and printed sources.

• The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL: http://www.cisco.com/en/US/products/products_catalog_links_launch.html

Cisco Press publishes a wide range of networking publications. Cisco suggests these titles for new and experienced users: Internetworking Terms and Acronyms Dictionary, Internetworking

Technology Handbook, Internetworking Troubleshooting Guide, and the Internetworking Design

Guide. For current Cisco Press titles and other information, go to Cisco Press online at this URL: http://www.ciscopress.com

Packet magazine is the Cisco quarterly publication that provides the latest networking trends, technology breakthroughs, and Cisco products and solutions to help industry professionals get the most from their networking investment. Included are networking deployment and troubleshooting tips, configuration examples, customer case studies, tutorials and training, certification information, and links to numerous in-depth online resources. You can access Packet magazine at this URL: http://www.cisco.com/go/packet iQ Magazine is the Cisco bimonthly publication that delivers the latest information about Internet business strategies for executives. You can access iQ Magazine at this URL: http://www.cisco.com/go/iqmagazine

Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL: http://www.cisco.com/en/US/about/ac123/ac147/about_cisco_the_internet_protocol_journal.html

Training—Cisco offers world-class networking training. Current offerings in network training are listed at this URL: http://www.cisco.com/en/US/learning/le31/learning_recommended_training_list.html

xvi

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

C H A P T E R

1

Overview

Cisco Aironet 1130AG Series Access Points provide a secure, affordable, and easy-to-use wireless LAN solution that combines mobility and flexibility with the enterprise-class features required by networking professionals. With a management system based on Cisco IOS software, the 1130 series access point is a Wi-Fi certified, wireless LAN transceiver.

The access point contains two integrated radios: a 2.4-GHz radio (IEEE 802.11g) and a 5-GHz radio

(IEEE 802.11a). You can configure the radios separately, using different settings on each radio.

The access point serves as the connection point between wireless and wired networks or as the center point of a stand-alone wireless network. In large installations, wireless users within radio range of an access point can roam throughout a facility while maintaining seamless, uninterrupted access to the network.

You can configure and monitor the access point using the command-line interface (CLI), the browser-based management system, or Simple Network Management Protocol (SNMP).

This chapter provides information on the following topics:

Hardware Features, page 1-2

Network Configuration Examples, page 1-7

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

1-1

Chapter 1 Overview

Hardware Features

C I S C O C O N F I D E N T I A L - D r a f t 1

Hardware Features

This section describes access point features. Refer to

Appendix C, “Access Point Specifications,”

for a list of access point specifications.

Key hardware features of the access point include:

Dual-radio operation (see

page 1-2 )

Ethernet port (see page 1-3 )

Console port (see page 1-3 )

LEDs, (see

page 1-3

) •

Power sources (see page 1-3 )

Anti-theft features (see

page 1-4

)

• UL 2043 certification (see

page 1-6

)

Figure 1-1

shows the access point hardware features.

Figure 1-1 Access Point Hardware Features

1

2

3

4

Status LED

48-VDC power port

Ethernet port (RJ-45)

Keyhole slot

5

6

7

Console port (RJ-45)

Mode button

Ethernet and Radio LEDs

Dual-Radio Operation

The access point supports simultaneous radio operation using a 2.4-GHz 802.11g radio and a 5-GHz

802.11a radio. Each radio uses 2-dBi dual-diversity integrated antennas.

The 5-GHz radio incorporates an Unlicensed National Information Infrastructure (UNII) radio transceiver operating in the UNII 5-GHz frequency bands. The 802.11g radio is called Radio0 and the

802.11a radio is called Radio1 .

1-2

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 1 Overview

Hardware Features

C I S C O C O N F I D E N T I A L - D r a f t 1

Ethernet Port

The auto-sensing Ethernet port accepts an RJ-45 connector, linking the access point to your 10BASE-T or 100BASE-T Ethernet LAN. The access point can receive power through the Ethernet cable from a power injector, switch, or power patch panel. The Ethernet MAC address is printed on the label on the back of the access point. The port is located in a cable bay area that is hidden by the top cover (see

Figure 1-1 ).

Console Port

The serial console port provides access to the access point’s command-line interface (CLI) using a terminal emulator program. The port is located in a cable bay area that is hidden by the top cover (see

Figure 1-1 ). Use an RJ-45 to DB-9 serial cable to connect your computer’s COM port to the access

point’s serial console port. (Refer to

Appendix E, “Console Cable Pinouts,”

for a description of the console port pinouts.) Assign the following port settings to a terminal emulator to open the management system pages: 9600 baud, 8 data bits, No parity, 1 stop bit and no flow control.

Note Your console cable connector must not include over-molding or a cable boot because of space limitations within the cable bay area of the access point.

LEDs

The report Ethernet has three LEDs to indicate Ethernet activity, association status, radio activity, and other status indications (refer to the

“Checking the Access Point LEDs” section on page 6-2 for

additional information).

The Status LED provides general operating status and error indications.

The Ethernet LED is located in the cable bay ares under the access point top cover. This LED signals

Ethernet traffic on the wired Ethernet LAN and provides Ethernet error indications.

• The Radio LED signals that wireless packets are being transmitted or received over the radio interface and provides radio error indications.

Figure 1-1 shows the locations of the three LEDs.

Power Sources

The access point can receive power from an external power module (supplied)or from inline power using the Ethernet cable. The access point supports the IEEE 802.3af inline power standard and the Cisco CDP

Power Negotiation protocol. Using inline power, you do not need to run a power cord to the access point because power is supplied over the Ethernet cable.

Warning This product must be connected to a power-over-ethernet (POE) IEEE 802.3af compliant power source or an

IEC60950 compliant limited power source.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

1-3

Hardware Features

Chapter 1 Overview

C I S C O C O N F I D E N T I A L - D r a f t 1

The access point supports the following power sources:

Power module (supplied)

Inline power:

Cisco Aironet 1300 Series Power Injector (supplied)

An inline power capable switch, such as Cisco Catalyst 3500XL, 3550, 4500, or 6500 switches

An inline power patch panel, such as the Cisco Catalyst Inline Power Patch Panel

Other inline power switches supporting the IEEE 802.3af inline power standard

Note Some switches and patch panels might not provide enough power to operate the access point when configured with both 2.4-GHz and 5-GHz radios. On power-up if access point is unable to determine that the power source can supply sufficient power, the access point automatically deactivates both radios to prevent an over-current condition. The access point also activates a Status LED low power error

indication and creates an error log entry (refer to the “Checking the Access Point LEDs” section on page 6-2 and the

“Low Power Condition” section on page 6-5 ).

Anti-Theft Features

There are three methods of securing the access point to help prevent theft:

• Security cable keyhole—You can use the security cable slot to secure the access point using a standard security cable, such as those used on laptop computers.

• Security hasp adapter—When you mount the access point on a wall or ceiling using the mounting plate and the security hasp, you can lock the access point to the plate with a padlock (see

Figure 1-2

).

Compatible padlocks are Master Lock models 120T and 121T or equivalent.

Note The security hasp adapter covers the cable bay area ( including the power port, Ethernet port, console port, and the mode button) to prevent the installation or removal of the cables or the activation of the mode button.

Figure 1-2 Access Point with Security Hasp Adapter

1-4

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

\

Chapter 1 Overview

C I S C O C O N F I D E N T I A L - D r a f t 1

1 Access point cover in open position

2 Security hasp adapter

3 Security padlock

Hardware Features

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

1-5

Hardware Features

Chapter 1 Overview

C I S C O C O N F I D E N T I A L - D r a f t 1

• Security screw—The access point contains a security screw hole (see

Figure 1-3 ) that can be used

to attach the access point to the mounting plate to restrict access point removal. When a security-type screw (user supplied) is used, access to the mounting screws that attach the mounting plate is greatly restricted.

Note The use of a security-type screw does not restrict access to the access point cables or the mode button.

Figure 1-3 Access Point Security Screw Hole

1 Access point cover in open position 2 Security screw hole

UL 2043 Certification

The access point has adequate fire resistance and low smoke-producing characteristics suitable for operation in a building's environmental air space, such as above suspended ceilings, in accordance with

Section 300-22(c) of the NEC, and with Sections 2-128, 12-010(3) and 12-100 of the Canadian

Electrical Code , Part 1, C22.1.

Caution The power injector and power module are not tested to UL 2043 and should not be placed in a building’s environmental air space, such as above suspended ceilings.

1-6

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 1 Overview

Network Configuration Examples

C I S C O C O N F I D E N T I A L - D r a f t 1

Network Configuration Examples

This section describes the access point’s role in three common wireless network configurations. The access point’s default configuration is as a root unit connected to a wired LAN or as the central unit in an all-wireless network. The repeater role requires a specific configuration.

Root Unit on a Wired LAN

An access point connected directly to a wired LAN provides a connection point for wireless users. If more than one access point is connected to the LAN, users can roam from one area of a facility to another without losing their connection to the network. As users move out of range of one access point, they automatically connect to the network (associate) through another access point. The roaming process is seamless and transparent to the user.

Figure 1-4

shows access points acting as root units on a wired LAN.

Figure 1-4 Access Points as Root Units on a Wired LAN - need new picture

Access Point

(Root Unit)

Wired LAN

Access Point

(Root Unit)

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

1-7

Chapter 1 Overview

Network Configuration Examples

C I S C O C O N F I D E N T I A L - D r a f t 1

Repeater Unit that Extends Wireless Range

An access point can be configured as a stand-alone repeater to extend the range of your infrastructure or to overcome an obstacle that blocks radio communication. The repeater forwards traffic between wireless users and the wired LAN by sending packets to either another repeater or to an access point connected to the wired LAN. The data is sent through the route that provides the best performance for the client.

Figure 1-5 shows an access point acting as a repeater. Consult the

Cisco IOS Software

Configuration Guide for Cisco Aironet Access Points for instructions on setting up an access point as a repeater.

Note Non-Cisco client devices might have difficulty communicating with repeater access points.

Figure 1-5 Access Point as Repeater - need new picture

Access Point

(Root Unit)

Wired LAN

Access Point

(Repeater)

1-8

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 1 Overview

Network Configuration Examples

C I S C O C O N F I D E N T I A L - D r a f t 1

Central Unit in an All-Wireless Network

In an all-wireless network, an access point acts as a stand-alone root unit. The access point is not attached to a wired LAN; it functions as a hub linking all stations together. The access point serves as the focal point for communications, increasing the communication range of wireless users.

Figure 1-6

shows an access point in an all-wireless network.

Figure 1-6 Access Point as Central Unit in All-Wireless Network - need new picture

Access Point

(Root Unit)

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

1-9

Network Configuration Examples

C I S C O C O N F I D E N T I A L - D r a f t 1

Chapter 1 Overview

1-10

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

C H A P T E R

2

Installing the Access Point

This chapter describes the installation of the access point and includes these sections:

Safety Information, page 2-2

Warnings, page 2-2

Unpacking the Access Point, page 2-3

Basic Installation Guidelines, page 2-3

Before Beginning the Installation, page 2-4

Installation Summary, page 2-7

Opening the Access Point Cover, page 2-8

Mounting the Access Point, page 2-9

Attaching the Access Point to the Mounting Plate, page 2-15

Connecting the Ethernet and Power Cables, page 2-17

Securing the Access Point, page 2-19

Powering Up the Access Point, page 2-21

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

2-1

Chapter 2 Installing the Access Point

Safety Information

C I S C O C O N F I D E N T I A L - D r a f t 1

Safety Information

Follow the guidelines in this section to ensure proper operation and safe use of the access point.

FCC Safety Compliance Statement

The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. When used with approved

Cisco Aironet antennas, Cisco Aironet products meet the uncontrolled environmental limits found in

OET-65 and ANSI C95.1, 1991. Proper installation of this radio according to the instructions found in this manual will result in user exposure that is substantially below the FCC recommended limits.

General Safety Guidelines

Do not hold any component containing a radio so that the antenna is very close to or touching any exposed parts of the body, especially the face or eyes, while transmitting.

The use of wireless devices in hazardous locations is limited to the constraints posed by the local codes, the national codes, and the safety directors of such environments.

Warnings

Translated versions of the following safety warnings are provided in

Appendix A, “Translated Safety

Warnings.”

Warning Read the installation instructions before you connect the system to its power source. Statement 1004

Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than:

15A Statement 1005

Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.

Statement 245B

Warning In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons. Statement 332

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

2-2

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 2 Installing the Access Point

Unpacking the Access Point

C I S C O C O N F I D E N T I A L - D r a f t 1

Unpacking the Access Point

Follow these steps to unpack the access point:

Step 1

Step 2

Step 3

Open the shipping container and carefully remove the contents.

Return all packing materials to the shipping container and save it.

Ensure that all items listed in the “Package Contents” section are included in the shipment. Check each item for damage. If any item is damaged or missing, notify your authorized Cisco sales representative.

Package Contents

Each access point package contains the following items:

Cisco Aironet 1130AG Series Access Point

Cisco Aironet 1130AG Series Power Module (Universal power supply)

Cisco Aironet 1130AG Series Power Injector

Mounting hardware kit

One mounting plate

Two suspended ceiling adjustable T-rail clips

One security hasp adapter

Four 6x32x¼ inch flat head Phillips head machine screws

One 8x32x3/16 inch pan head Phillips head machine screws

2 #8 plastic wall anchors

– 2 #8x32x1inch pan head screws

Quick Start Guide: Cisco Aironet 1130AG Series Access Point •

• Cisco product registration and Cisco documentation feedback cards

If anything is missing or damaged, contact your Cisco representative for support.

Basic Installation Guidelines

Because the access point is a radio device, it is susceptible to interference that can reduce throughput and range. Follow these basic guidelines to ensure the best possible performance:

Install the access point in an area where metal structures such as shelving units, bookcases, filing cabinets, and metal gridwork do not block the radio signals to and from the access point.

Install the access point away from microwave ovens. Microwave ovens operate on the same frequency as the access point and can cause signal interference.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

2-3

Chapter 2 Installing the Access Point

Before Beginning the Installation

C I S C O C O N F I D E N T I A L - D r a f t 1

Before Beginning the Installation

Before you begin the installation process, please refer to these sections to become familiar with the access point and the mounting hardware:

“Access Point Layout and Connectors” section on page 2-4

“Mounting Plate” section on page 2-5

“Suspended Ceiling Adjustable T-Rail Clips” section on page 2-6

Access Point Layout and Connectors

Figure 2-1

identifies the main access point hardware features.

Figure 2-1 Access Point Hardware Features - TBD

1

2

3

4

Status LED

48-VDC power port

Ethernet port (RJ-45)

Keyhole slot

5

6

7

Console port (RJ-45)

Mode button

Ethernet and Radio LEDs

Note There is a second keyhole slot located on the bottom of the unit near the security slot.

2-4

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 2 Installing the Access Point

Before Beginning the Installation

C I S C O C O N F I D E N T I A L - D r a f t 1

Mounting Plate

The access point mounting plate is designed to accomodate multiple mounting methods. The mounting holes on the plate are marked so you can easily identify the correct holes for a specific mounting method.

You can use the mounting plate as a template to mark the locations for the cable hole and the mounting holes for your wall or ceiling installation. Refer to

Figure 2-2 to locate the various mounting holes for

the method you intend to use.

Figure 2-2 Mounting Plate

OL-6226-01

1 Keyhole clip

2 Screw holes (A, B, C)

3 Location for cable access hole

4 Screw hole (X)

5 Security screw hole

6 Padlock hole

The mounting plate features are described below:

Keyhole clips—used to attach the access point to the mounting plate. The keyhole clips slide into the access point keyhole slots on the bottom of the unit.

Screw holes (A, B, C)—used to attach to the suspended ceiling adjustable T-rail clips.

Screw hole (X)—used to attach to a network cable box, wall, or ceiling. The mounting kit contains two 8x32x1 inch pan head screws and wall anchors for wall or ceiling mounting.

Security screw hole—used to secure the access point to the mounting plate.

Note You can use a special security screw to restrict the removal of the access point from the mounting plate.

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

2-5

Chapter 2 Installing the Access Point

Before Beginning the Installation

C I S C O C O N F I D E N T I A L - D r a f t 1

• Padlock hole—used to attach a padlock to secure the access point to the mounting plate. Compatible padlocks are Master Lock models 120T and 121T or equivalent. The security hasp adapter can also be used with the padlock for increase security protection.

Note The security hasp covers the cable bay area ( including the power port, Ethernet port, console port, and the mode button) to prevent the installation or removal of the cables or the activation of the mode button.

Suspended Ceiling Adjustable T-Rail Clips

The accessory kit contains two suspended ceiling adjustable T-rail clips; one for standard ceiling tile rails and the other for recessed ceiling tile rails. The clips are adjustable to accomodate three standard

T-rail widths. Each clip contains detents that are used to adjust the clip to the T-rail. Each detent contains markings that indicate the T-rail width and the hole letter that corresponds to the correct mounting holes on the mounting plate.

Figure 2-3 shows the details of the adjustable T-rail clips.

Figure 2-3 T-Rail Clip Features

1 Adjustable T-rail clip

2 Mounting plate screw holes

(8x32 flat head screw)

2-6

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

3 T-rail locking screw

4 T-rail width adjustment detents (A, B, C) correspond to the A, B, and C holes on the mounting plate

OL-6226-01

Chapter 2 Installing the Access Point

Installation Summary

C I S C O C O N F I D E N T I A L - D r a f t 1

The adjustable T-rail clip attaches to the mounting plate using four 6x32x1/4 inch flat head screws. The

A, B, and C holes on the T-rail clips and the mounting plate correspond to these T-rail widths:

A holes—used for 1 1/2 in (38 mm) T-rails

B holes—used for 15/16 in (24 mm) T-rails

• C holes—used for 9/16 in (15 mm) T-rails

Figure 2-4 indicates where you should push to open and close the adjustable T-rail clips.

Figure 2-4 Adjusting the T-Rail Clips

1 Push here to open 2 Push here to close

Installation Summary

While installing the access point, you must perform the following operations:

Open the access point cover (see

“Opening the Access Point Cover” section on page 2-8

).

Mount the access point on a convenient flat horizontal or vertical surface, such as a desktop, book shelf, file cabinet, wall, ceiling, or suspended ceiling T-rail (see the

“Mounting the Access Point” section on page 2-9 ).

Attach the access point to the mounting plate (see the

“Attaching the Access Point to the Mounting

Plate” section on page 2-15 ).

Connect Ethernet and power cables (see the “Connecting the Ethernet and Power Cables” section on page 2-17

).

Secure the access point (see the

“Securing the Access Point” section on page 2-19 ).

Configure basic settings (refer to

Chapter 3, “Configuring the Access Point for the First Time” ).

Configure security and other access point options (refer to the Cisco IOS Software Configuration

Guide for Cisco Aironet Access Points ).

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

2-7

Chapter 2 Installing the Access Point

Opening the Access Point Cover

C I S C O C O N F I D E N T I A L - D r a f t 1

Opening the Access Point Cover

The top cover provides access to the access point cable bay area containing the power connector,

Ethernet port, console serial port, the mode button, and the Ethernet and Radio LEDs.

Caution Do not attempt to pry open or lift the top cover of the access point, because you could damage the cover.

Carefully read the instructions in this section before attempting to open the access point cover.

The cover is designed to partially open by sliding back from a secured position. Follow these steps to open the top cover:

Step 1 Locate the cable opening on the end of the unit (see

Figure 2-5 ).

Figure 2-5 Cable Opening in Access Point Housing

1 Top cover 2 Cable Opening

Step 2 Place your thumb on the top cover (above the triangle mark ) and gently push towards the Status

LED.

2-8

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 2 Installing the Access Point

Mounting the Access Point

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 3 Continue to slowly slide the cover back across the access point until you reach the cover stop (see

Figure 2-6 ).

Figure 2-6 Opening the Access Point Cover

1 Access point cover (maximum open position) 3 Opening direction

2 Cable bay area 4 Cable opening (in access point housing)

Mounting the Access Point

This section describes the steps necessary to mount the access point using thesemethods:

Horizontal or vertical surface—see the

page 2-10

Under a suspended ceiling— “Mounting Below a Suspended Ceiling” section on page 2-11

Network cable box—

“Mounting on a Horizontal or Vertical Surface” section on

“Mounting on a Network Cable Box” section on page 2-14

Desktop or shelf—see the

“Mounting on a Desktop or Shelf” section on page 2-14

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

2-9

Chapter 2 Installing the Access Point

Mounting the Access Point

C I S C O C O N F I D E N T I A L - D r a f t 1

Mounting on a Horizontal or Vertical Surface

Follow these steps to mount the access point on a horizontal or vertical surface:

Step 1 Use the mounting plate as a template to mark the locations of the two mounting holes (labled with an X) and the location of the cable access hole (see

Figure 2-7

).

Figure 2-7 Mounting Plate

1 Keyhole clip

2 Cable access hole location

3 X mounting hole

4 Padlock hole

Step 2

Step 3

Step 4

Drill one of the following sized holes at the X mounting hole locations you marked:

3/16 in. (4.7 mm) if you are using the supplied wall anchors

1/8 in. (6.3 mm) if you are not using wall anchors

Insert the wall anchors into the mounting holes if you are using them.

If needed, drill or cut a cable access hole large enough for the access point cables and pull the cables through the access hole until you have about 1 foot of exposed cables protruding from the hole.

2-10

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 2 Installing the Access Point

Mounting the Access Point

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 5

Step 6

Position the mounting plate over the wall anchors or the drilled holes.

Insert two 8x32x1inch pan head screws in the X mounting holes and tightening.

To attach the access point to the mounting plate, see

“Attaching the Access Point to the Mounting Plate” section on page 2-15 .

Mounting Below a Suspended Ceiling

Note To comply with NEC code, a #10-24 grounding lug is provided on the mounting plate.

You should review

Figure 2-8 before beginning the mounting process.

Figure 2-8 Adjustable T-Rail Clips

OL-6226-01

1 T-rail locking set screw

2 Mounting plate screw holes

3 T-rail width detents (A, B, or C)

Follow these steps to mount your access point on a suspended ceiling:

Step 1 Decide where you want to mount the access point on your suspended ceiling.

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

2-11

Chapter 2 Installing the Access Point

Mounting the Access Point

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 2

Step 9

Select the appropriate adjustable T-rail clip for your suspended ceiling and open the clip to the maximum

(see

Figure 2-4 ).

Unscrew the two T-rail locking set screws to enable placing the clip over a T-rail.

Place the T-rail clip over the T-rail and close the T-rail clip (see

Figure 2-4

).

Tighten the two T-rail locking set screws to prevent the T-rail clip from moving.

Observe the T-rail width detent letter (A, B, or C) that corresponds to the T-rail width.

Align the corresponding (A, B, or C) holes on the mounting plate over the T-rail mounting plate holes.

Hold the mounting plate and insert a 6x32x1/4 flat head screw into each of the corresponding (A, B, or

C) holes and tighten.

If needed, drill or cut a cable access hole (see

Figure 2-7 ) large enough for the access point cables and

pull the cables through the access hole until you have about 1 foot of exposed cables protruding from the hole.

To attach the access point to the mounting plate, see

“Attaching the Access Point to the Mounting Plate” section on page 2-15 .

2-12

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 2 Installing the Access Point

Mounting Above a Suspended Ceiling

C I S C O C O N F I D E N T I A L - D r a f t 1

Mounting Above a Suspended Ceiling

The access point mounting bracket is designed to be integrated into the T-bar grid above the tiles of a suspended ceiling. The access point uses a T-bar box hanger (not supplied) such as the Erico Caddy 512 or B-Line BA12 and should be oriented just above the top surface of a standard 5/8-in. (1.59 cm) ceiling tile. You may need to modify a thicker tile to allow room for the access point.

Follow these steps to mount the access point above a suspended ceiling. Refer

Figure 2-9

before proceeding.

Figure 2-9 T-Bar Grid Mounting Bracket Parts

6 1 3 4 2 6 1

5

1

2

3

Suspended ceiling T-rail

T-bar box hanger

Bracket mounting clip

4

5

6

Access point mounting bracket

Access point

T-rail clip

Step 1

Step 2

Insert the bracket mounting clip’s tab into the large hole on the access point mounting bracket.

Place the clip over the T-bar box hanger (refer to

Figure 2-10

) and secure it to the access point mounting bracket with the 1/4-20 fastener (supplied with the T-bar hanger).

Figure 2-10 T-Bar and Mounting Bracket

OL-6226-01

Note

Figure 2-10 shows the access point mounting bracket mounted perpendicular to the T-bar box

hanger. You can also mount the bracket parallel to the T-bar box hanger.

Step 3 Remove a ceiling tile adjacent to the mounting location.

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

2-13

Chapter 2 Installing the Access Point

Mounting Above a Suspended Ceiling

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 4

Step 5

Step 6

Step 7

Step 8

Configure the ends of the T-bar box hanger to allow for maximum clearance above the ceiling tile. See the illustration above.

Attach the T-rail clips on the each end of the T-bar box hanger to the ceiling grid T-rails. Make sure the clips are securely attached to the T-rails.

Connect a drop wire to a building structural element and the hole provided in the bracket mounting clip.

This additional support is required in order to comply with the U.S. National Electrical Safety Code.

Attach the access point to the access point mounting bracket.

Connect the Ethernet cables to the access point.

Note The power module and power injector are not rated for mounting above suspended ceilings.

Therefore, you must use the Ethernet cable to supply power.

Step 9

Step 10

If you need additional security, you can secure the access point to a nearby immovable object using a

Kensington lock and security cable.

Verify that the access point is operating before replacing the ceiling tile.

Mounting on a Network Cable Box

Follow these steps to mount the access point on a network cable box.

Step 1

Step 2

Step 3

Position the mounting plate over the newtowk cable box and align the two mounting holes (labled with a X) with the network cable box holes.

Hold the mounting plate and insert a 6x32x1/4 flat head screw into each of the X mounting holes and tighten.

Pull the access point cables out of the network box until there is about 1 foot of exposed cables protruding from the box.

To attach the access point to the mounting plate, see

“Attaching the Access Point to the Mounting Plate” section on page 2-15 .

Mounting on a Desktop or Shelf

When placing the access point on a desktop of shelf, you do not need the mounting plate. The access point has four rubber pads on the bottom to help prevent sliding or scratching the surface of your desktop or shelf. For information on connecting the access point cables, see the

“Connecting the Ethernet and

Power Cables” section on page 2-17

.

2-14

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 2 Installing the Access Point

Attaching the Access Point to the Mounting Plate

C I S C O C O N F I D E N T I A L - D r a f t 1

Rotating the Cisco Logo

The Cisco logo on the top of the unit can be rotated to correctly position the logo for any mounting arrangement, such as when the unit is mounted on a vertical wall, the logo should oriented with the Cisco

Systems positioned on top. The logo should always be oriented to ease reading.

To rotate the Cisco logo, peform these steps:

Step 1 Place the end of an opened paper clip into one of the holes on the logo assembly (see

Figure 2-11

).

Figure 2-11 Cisco Logo Holes

1 Cisco logo

3 Logo assembly holes

2 Status LED

Step 2

Step 3

Using the paper clip as a handle, rotate the logo until you reach the desired orientation.

Remove the paper clip.

Attaching the Access Point to the Mounting Plate

Follow these steps to attach the access point to the mounting plate:

Step 1

Step 2

Open the access point cover (see the

“Opening the Access Point Cover” section on page 2-8

).

In the cable bay area, pull the cables through one of the access point cable openings (see

Figure 2-6 ).

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

2-15

Chapter 2 Installing the Access Point

Attaching the Access Point to the Mounting Plate

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 3 In the cable bay area, line up the visible access point keyhole with the mounting plate keyhole clip located near the security padlock hole (see

Figure 2-12 ).

Figure 2-12 Aligning the Keyhole Clip to the Access Point Keyhole

1 Access point keyhole

2 Mounting plate keyhole clip

3 Mounting plate

4

5

Security screw hole

Padlock hole

Step 4

Step 5

Step 6

Insert the keyhole clip into the keyhole and maintain a slight pressure to hold the access point in place.

Slightly rotate the access point from side-to-side until you hear the second keyhole clip falling into the other keyhole (not visible).

Slide the access point back over the keyhole clips. You will hear a click when the locking detent contacts the access point and locks it into place.

For instructions on connecting your cables, refer to the

“Connecting the Ethernet and Power Cables” section on page 2-17 .

2-16

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 2 Installing the Access Point

Connecting the Ethernet and Power Cables

C I S C O C O N F I D E N T I A L - D r a f t 1

Connecting the Ethernet and Power Cables

The access point receives power through the Ethernet cable or an external power module.

Figure 2-13

shows the power options for the access point.

Figure 2-13 Access Point Power Options - need new picture with Ajax

Option 1 Option 2

Switch

(without inline power)

Switch with inline power

SYST

RPS

STAT

UTIL DUPLX SPEED

MODE

1 2

3

4 5

6

7 8

9

10

11

10Base-T / 10

12

0Base-TX

13

14 15

16

17

18 19

20

21 22

23

24

Catalyst 2950

SERIES

100Base-FX

23 24

Option 3

Switch

(without inline power)

SYST

RPS

STAT UTIL

DUPLX SPEED

MODE

1

2 3

4

5

6 7

8

9 10

11

10Base-T / 10

0Base-TX

12

13 14

15

16 17

18

19

20 21

22

23 24

Catalyst 2950

SERIES

24

SYST

RPS

STAT

UTIL DUPLX SPEED

MODE

1 2

3

4 5

6

7 8

9

10

11

10Base-T / 10

12

0Base-TX

13

14 15

16

17

18 19

20

21 22

23

24

Catalyst 2950

SERIES

100Base-FX

23

24

Inline Power

Patch Panel

Power injector

TWO SYST

RPS

STAT UTIL DUPLX

SPEED

MODE

Power cord

Universal power supply

Access Point

Option 4

The access point power options are listed below:

• A switch with inline power, such as a Cisco Catalyst 3500XL, 3550-24 PWR, 4000, or 6500 switch

An inline power patch panel, such as a Cisco Catalyst Inline Power Patch Panel

A power injector

A 48 VDC power module (Universal power supply)

Note Currently, the Catalyst 3550-24 PWR switch supports sufficient power for both the 2.4-GHz radio and the 5-GHz radio. Other switches and power patch panels might not provide enough power for simultaneous operation of both radios.

Note If you use in-line power from a switch or patch panel, do not connect the power module to the access point. Using two power sources on the access point might cause the switch or patch panel to shut down the port to which the access point is connected.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

2-17

Chapter 2 Installing the Access Point

Connecting the Ethernet and Power Cables

C I S C O C O N F I D E N T I A L - D r a f t 1

Connecting to an Ethernet Network with an Inline Power Source

Caution The Cisco Aironet Power Injectors are not tested to UL 2043 and should not be placed in a building's environmental air space, such as above suspended ceilings.

Follow these steps to connect the access point to the Ethernet LAN when you have an inline power source:

Step 1

Step 2

Step 3

If necessary, open the access point cover (see the

“Opening the Access Point Cover” section on page 2-8 ).

Pull the Category 5 Ethernet cable out of the access point cable bay area approximately 1 foot.

Loop the cable back towards the Ethernet connector (see

Figure 2-14 )

Figure 2-14 Looping the Ethernet Cable

Step 4

Step 5

Step 6

Step 7

Connect the Ethernet cable to the RJ-45 Ethernet connector labeled Ethernet on the access point (see

Figure 2-1

).

Push or pull the excess cable length (the loop) back through the access point cable bay area.

Close the access point cover by sliding it over the cable bay area until a click is heard.

Connect the other end of the Ethernet cable to one of the following:

• A switch with inline power, such as a Cisco Catalyst 3500XL, 3550-24 PWR, 4000, or 6500 switch.

An inline power switch panel, such as a Cisco Catalyst Inline Power Patch Panel.

The end of a Cisco Aironet power injector labeled To AP/Bridge . Connect the other end labeled To

Network to your 10/100 Ethernet LAN.

Note When you use a power supply or power injector to power the access point, you must use the power supply included with your access point and a Cisco Aironet Power Injector (1100, 1130, or 1200 series).

2-18

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 2 Installing the Access Point

Securing the Access Point

C I S C O C O N F I D E N T I A L - D r a f t 1

Connecting to an Ethernet Network with Local Power

Follow these steps to connect the access point to an Ethernet LAN when you are using a local power source:

Step 1

Step 2

Step 3

If necessary, open the access point cover (see the

“Opening the Access Point Cover” section on page 2-8

).

Pull the Category 5 Ethernet cable and the power module cable out of the access point cable bay area approximately 1 foot.

Loop the Ethernet cable back towards the access point Ethernet connector (see

Figure 2-14

).

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Connect the Ethernet cable to the RJ-45 Ethernet connector labeled Ethernet on the access point (see

Figure 2-1 ).

Loop the power cable back towards the access point 48-VDC power port (see Figure 2-1

for the location of the power port).

Connect the power module output connector to the access point power port.

Push or pull the excess cable lengths (both loops) back through the access point cable bay area.

Close the access point cover by sliding it over the cable bay area until a click is heard.

Plug the other end of the Ethernet cable into an unpowered Ethernet port on your LAN network.

Plug the other end of the power module into an approved 100- to 240-VAC outlet.

For information on securing your access point, see the

“Securing the Access Point” section on page 2-19 .

Securing the Access Point

The access point supports two methods of restricting the removal of the access point.

Using a security cable

Securing the access point to the mounting plate

Using a Security Cable

The access point housing provides a security cable slot to secure the access point using a standard security cable, such as those used on laptop computers. The access point security cable slot is located on one side of the unit.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

2-19

Chapter 2 Installing the Access Point

Securing the Access Point

C I S C O C O N F I D E N T I A L - D r a f t 1

Securing the Access Point to the Mounting Plate

The mounting plate contains a security padlock hole and a security screw hole to enable you to secure your access point to the mounting plate to restrict it’s removal. You can use a security-type screw (that you provide) to attach the access point to the mounting plate using the security screw hole (see

Figure 2-12

).

Note Using a security-type screw to secure the access point to the mounting plate does not prevent someone from inserting or removing the access point cables or pressing the mode button.

You can use the security hasp adapter (supplied) and a padlock (that you provide) to secure your access point to the mounting plate. Compatible padlocks are Master Lock models 120T or 121T.

Note The security hasp adapter covers the cable bay area (including the power port, Ethernet port, console port, and the mode button) to prevent the installation or removal of the cables or the activation of the mode button.

Follow these instructions to install the security hasp adapter:

Step 1

Step 2

Open the access point cover (see the

“Opening the Access Point Cover” section on page 2-8 ).

Carefully insert the access point security hasp tab into the notch on the security hasp adapter (see

Figure 2-15

).

Figure 2-15 Installing the Security Hasp Adapter

2-20

1 Access point security hasp tab

2 Security hasp notch

3 Security hasp adapter

Step 3

Step 4

Push down on the security hasp adapter to ensure the padlock hole is not blocked.

Insert a padlock into the padlock hole and lock the padlock.

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 2 Installing the Access Point

Powering Up the Access Point

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 5

Step 6

Position the padlock into the padlock area.

Close the access point cover by sliding it over the security hasp adapter until you hear a click.

Powering Up the Access Point

When power is applied to the access point, it begins a routine power-up sequence that you can monitor by observing the Status LED on top of the access point. On initial power-up the LED changes colors indicating various POST activities, such as the Status LED turns dark green for about 30 seconds to indicate loading of the Cisco IOS operating system. After a successful power-up sequence, the LED turns light green to signify there are no client devics associated or it turns light blue to signify that there are client devices associated. Refer to

Chapter 6, “Troubleshooting,” for complete LED descriptions.

When the Status LED turns light green or light blue, you are ready to obtain the access point’s IP address and perform an initial configuration. For instructions on assigning basic settings to the access point, refer to

Chapter 3, “Configuring the Access Point for the First Time,”

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

2-21

Powering Up the Access Point

Chapter 2 Installing the Access Point

C I S C O C O N F I D E N T I A L - D r a f t 1

2-22

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

C H A P T E R

3

Configuring the Access Point for the First Time

This chapter describes how to configure basic settings on your access point for the first time. The contents of this chapter are similar to the instructions in the quick start guide that shipped with your access point. You can configure all the settings described in this chapter using the CLI, but it might be simplest to browse to the access point’s web-browser interface to complete the initial configuration and then use the CLI to enter additional settings for a more detailed configuration.

This chapter contains these sections:

Before You Start, page 3-2

Obtaining and Assigning an IP Address, page 3-3

Connecting to the Access Point Locally, page 3-3

Assigning Basic Settings, page 3-4

Protecting Your Wireless LAN, page 3-9

Using the IP Setup Utility, page 3-9

Assigning an IP Address Using the CLI, page 3-12

Using a Telnet Session to Access the CLI, page 3-12

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

3-1

Chapter 3 Configuring the Access Point for the First Time

Before You Start

C I S C O C O N F I D E N T I A L - D r a f t 1

Before You Start

Before you install the access point, make sure you are using a computer connected to the same network as the access point, and obtain the following information from your network administrator:

• A system name for the access point

The case-sensitive wireless service set identifiers (SSIDs) for your 802.11g and 02.11a radio networks

If not connected to a DHCP server, a unique IP address for your access point (such as

172.17.255.115)

If the access point is not on the same subnet as your PC, a default gateway address and subnet mask

A Simple Network Management Protocol (SNMP) community name and the SNMP file attribute (if

SNMP is in use)

If you use IPSU to find or assign the access point IP address, the MAC address from the label on the bottom of the access point (such as 00164625854c)

Resetting the Access Point to Default Settings

Using the Mode Button

If you need to start over during the initial setup process, follow these steps to reset the access point to factory default settings using the access point MODE button:

Step 1

Step 2

Step 3

Open the access point cover (refer to the

“Opening the Access Point Cover” section on page 2-8 ).

Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.

Press and hold the MODE button while you reconnect power to the access point, approximately 2 to 3 seconds, and release the button. All access point settings return to factory defaults.

Using the Web-Browser Interface

Prior to using the web-browser interface, you must have the access point IP address (see the

“Obtaining and Assigning an IP Address” section on page 3-3

).

Follow these steps to return to default settings using the web-browser interface:

Step 1

Step 2

Step 3

Step 4

Step 5

Open your Internet browser. You must use Microsoft Internet Explorer (version 5.x or later) or Netscape

Navigator (version 4.x).

Enter the access point’s IP address in the browser address line and press Enter . An Enter Network

Password window appears.

Enter your username in the User Name field. The default username is Cisco .

Enter the access point password in the Password field and press Enter . The default password is Cisco .

The Summary Status page appears.

Click System Software and the System Software screen appears.

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

3-2 OL-6226-01

Chapter 3 Configuring the Access Point for the First Time

Obtaining and Assigning an IP Address

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 6

Step 7

Click System Configuration and the System Configuration screen appears.

Click the Reset to Defaults button.

Note If the access point is configured with a static IP address, the IP address does not change.

Obtaining and Assigning an IP Address

To browse to the access point’s Express Setup page, you must either obtain or assign the access point’s

IP address using one of the following methods:

Connect to the access point console port and assign a static IP address. Follow the steps in the

“Connecting to the Access Point Locally” section on page 3-3 to connect to the console port.

Use a DHCP server (if available) to automatically assign an IP address. You can find out the

DHCP-assigned IP address using one of the following methods:

– Connect to the access point console port and use the show ip interface brief command to display the IP address. Follow the steps in the

“Connecting to the Access Point Locally” section on page 3-3

to connect to the console port.

Provide your organization’s network administrator with your access point’s Media Access

Control (MAC) address. Your network administrator will query the DHCP server using the

MAC address to identify the IP address. The access point’s MAC address is on label attached to the bottom of the access point.

Use the Cisco IP Setup Utility (IPSU) to identify the assigned address. You can also use IPSU to assign an IP address to the access point if it did not receive an IP address from the DHCP server. IPSU runs on most Microsoft Windows operating systems: Windows 9x, 2000, Me, NT, and XP.

For information on IPSU, refer to

“Using the IP Setup Utility” section on page 3-9

.

Connecting to the Access Point Locally

If you need to configure the access point locally (without connecting the access point to a wired LAN), you can connect a PC to its console port using a DB-9 to RJ-45 serial cable. Follow these steps to open the CLI by connecting to the access point console port:

Step 1

Step 2

Open the access point cover (refer to “Opening the Access Point Cover” section on page 2-8

).

Connect a nine-pin, female DB-9 to RJ-45 serial cable to the RJ-45 console port on the access point and to the COM port on a computer.

Tip If your serial cable enters from the lower cable bay area, you should loop the cable as shown in

Figure 2-14 .

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

3-3

Chapter 3 Configuring the Access Point for the First Time

Assigning Basic Settings

C I S C O C O N F I D E N T I A L - D r a f t 1

Figure 3-1

shows the console port location.

Figure 3-1 Console Port Location

1 Console port

Note The Cisco part number for the DB-9 to RJ-45 serial cable is AIR-CONCAB1200. Browse to http://www.cisco.com/go/marketplace to order a serial cable.

Step 3 Set up a terminal emulator on your PC to communicate with the access point. Use the following settings for the terminal emulator connection: 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control.

Assigning Basic Settings

After you determine or assign the access point’s IP address, you can browse to the access point’s Express

Setup page and perform an initial configuration:

Step 1

Step 2

Step 3

Step 4

Open your Internet browser. You must use Microsoft Internet Explorer (version 5.x or later) or Netscape

Navigator (version 4.x).

Enter the access point’s IP address in the browser address line and press Enter . An Enter Network

Password screen appears.

Press Tab to bypass the Username field and advance to the Password field.

Enter the case-sensitive password Cisco and press Enter . The Summary Status page appears.

3-4

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 3 Configuring the Access Point for the First Time

C I S C O C O N F I D E N T I A L - D r a f t 1

Figure 3-2 shows the Summary Status page.

Figure 3-2 Summary Status Page

Assigning Basic Settings

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

3-5

Chapter 3 Configuring the Access Point for the First Time

Assigning Basic Settings

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 5 Click Express Setup . The Express Setup screen appears.

Figure 3-3 shows the Express Setup page.

Figure 3-3 Express Setup Page

Step 6 Enter the configuration settings you obtained from your system administrator. The configurable settings include:

System Name — The system name, while not an essential setting, helps identify the access point on your network. The system name appears in the titles of the management system pages.

Configuration Server Protocol —Click on the button that matches the network’s method of IP address assignment.

DHCP —IP addresses are automatically assigned by your network’s DHCP server.

Static IP —The access point uses a static IP address that you enter in the IP address field.

3-6

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 3 Configuring the Access Point for the First Time

Assigning Basic Settings

C I S C O C O N F I D E N T I A L - D r a f t 1

• IP Address —Use this setting to assign or change the access point’s IP address. If DHCP is enabled for your network, leave this field blank.

Note If the access point’s IP address changes while you are configuring the access point using the web-browser interface or a Telnet session over the wired LAN, you lose your connection to the access point. If you lose your connection, reconnect to the access point using its new IP address.

Follow the steps in the

“Resetting the Access Point to Default Settings” section on page 3-2

if you need to start over.

IP Subnet Mask —Enter the IP subnet mask provided by your network administrator so the IP address can be recognized on the LAN. If DHCP is enabled, leave this field blank.

Default Gateway —Enter the default gateway IP address provided by your network administrator.

If DHCP is enabled, leave this field blank.

Radio Service Set ID (SSID) —Enter the case-sensitive SSID (32 alphanumeric characters maximum) provided by your network administrator. The SSID is a unique identifier that client devices use to associate with the access point.

Broadcast SSID in Beacon —Use this setting to allow devices that do not specify an SSID to associate with the access point.

– Yes —This is the default setting; it allows devices that do not specify an SSID to associate with the access point.

– No —Devices must specify an SSID to associate with the access point. With No selected, the

SSID used by the client devices must match exactly the access point’s SSID.

Role in Radio Network —Click on the button that describes the role of the access point on your network. Select Access Point (Root) if your access point is connected to the wired LAN. Select

Repeater (Non-Root) if it is not connected to the wired LAN.

Optimize Radio Network for —Use this setting to select either preconcerted settings for the access point radio or customized settings for the access point radio.

– Throughput —Maximizes the data volume handled by the access point but might reduce its range.

Range —Maximizes the access point’s range but might reduce throughput.

Custom —The access point uses settings you enter on the Network Interfaces: Radio-802.11b

Settings page. Clicking Custom takes you to the Network Interfaces: Radio-802.11b Settings page.

Aironet Extensions —Enable this setting if there are only Cisco Aironet devices on your wireless

LAN.

SNMP Community —If your network is using SNMP, enter the SNMP Community name provided by your network administrator and select the attributes of the SNMP data (also provided by your network administrator).

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

3-7

Chapter 3 Configuring the Access Point for the First Time

Assigning Basic Settings

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 7 Click Apply to save your settings. If you changed the IP address, you lose your connection to the access point. Browse to the new IP address to reconnect to the access point.

Your access point is now running but probably requires additional configuring to conform to your network’s operational and security requirements. Consult the chapters in this manual for the information you need to complete the configuration.

Note You can restore the access point to its factory defaults by unplugging the power jack and plugging it back in while holding down the Mode button for 2 to 3 seconds.

Default Settings on the Express Setup Page

Table 3-1 lists the default settings for the settings on the Express Setup page.

Table 3-1 Default Settings on the Express Setup Page

Setting Default

System Name ap

Configuration Server Protocol DHCP

IP Address

IP Subnet Mask

Assigned by DHCP by default; if DHCP is disabled, the default setting is 10.0.0.1

Assigned by DHCP by default; if DHCP is disabled, the default setting is 255.255.255.224

Default Gateway

Radio Service Set ID (SSID)

Broadcast SSID in Beacon

Assigned by DHCP by default; if DHCP is disabled, the default setting is 0.0.0.0

tsunami

Yes

1

Role in Radio Network

Optimize Radio Network for

Aironet Extensions

SNMP Community

Access point (root)

Throughput

Enable defaultCommunity

1.

When you assign multiple SSIDs, this setting no longer appears.

3-8

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 3 Configuring the Access Point for the First Time

Protecting Your Wireless LAN

C I S C O C O N F I D E N T I A L - D r a f t 1

Protecting Your Wireless LAN

After you assign basic settings to your access point, you must configure security settings to prevent unauthorized access to your network. Because it is a radio device, the access point can communicate beyond the physical boundaries of your building. Configure some combination of these security features to protect your network from intruders:

• Unique SSIDs that are not broadcast in the access point beacon (see Cisco IOS Software

Configuration Guide for Cisco Aironet Access Points )

WEP and additional WEP features, such as TKIP and broadcast key rotation (see Cisco IOS Software

Configuration Guide for Cisco Aironet Access Points)

Dynamic WEP and client authentication (see Cisco IOS Software Configuration Guide for Cisco

Aironet Access Points )

Using the IP Setup Utility

IPSU enables you to find the access point’s IP address when it has been assigned by a DHCP server. You can also use IPSU to set the access point’s IP address and SSID if they have not been changed from the default settings. This section explains how to install the utility, how to use it to find the access point’s IP address, and how to use it to set the IP address and the SSID.

Note IPSU can be used only on the following operating systems: Windows 95, 98, NT, 2000, ME, or XP.

Tip Another simple way to find the access point’s IP address is to look on the Status screen in the Aironet

Client Utility on a client device associated to the access point.

Obtaining and Installing IPSU

IPSU is available on the Cisco web site. Follow these steps to obtain and install IPSU:

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Use your Internet browser to access the Cisco Software Center at the following URL: http://www.cisco.com/public/sw-center/sw-wireless.shtml

Click Option 2: Aironet Wireless Software Display Tables .

Locate the access point firmware and utilities section and click Cisco Aironet 1130 Series (Cisco IOS

Software) .

Click IPSUvxxxxxx.exe

. The vxxxxxx identifies the software package version number.

On the Encryption Authorization Form, enter the requested information, read the encryption information, and check the boxes that apply.

Click Submit .

Read and accept the terms and conditions of the Software License Agreement.

Select the file again to download it.

Download and save the file to a temporary directory on your hard drive and then exit the Internet browser.

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01 3-9

Chapter 3 Configuring the Access Point for the First Time

Using the IP Setup Utility

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 10

Step 11

Double-click IPSUvxxxxxx.exe

in the temporary directory to expand the file.

Double-click Setup.exe

and follow the steps provided by the installation wizard to install IPSU.

The IPSU icon appears on your computer desktop.

Using IPSU to Find the Access Point’s IP Address

If your access point receives an IP address from a DHCP server, you can use IPSU to find its IP address.

Because IPSU sends a reverse-ARP request based on the access point MAC address, you must run IPSU from a computer on the same subnet as the access point. Follow these steps to find the access point’s IP address:

Step 1 Double-click the IPSU icon on your computer desktop to start the utility. The IPSU screen appears (see

Figure 3-4

).

Figure 3-4 IPSU Get IP Address Screen

Step 2

Step 3

When the utility window opens, make sure the Get IP addr radio button in the Function box is selected.

Enter the access point’s MAC address in the Device MAC ID field. The access point’s MAC address is printed on the label on the bottom of the unit. It should contain six pairs of hexadecimal digits. Your access point’s MAC address might look like the following example:

000164xxxxxx

Note The MAC address field is not case-sensitive.

Step 4

Step 5

Click Get IP Address .

When the access point’s IP address appears in the IP Address field, write it down.

If IPSU reports that the IP address is 10.0.0.1, the default IP address, then the access point did not receive a DHCP-assigned IP address. To change the access point IP address from the default value using IPSU, refer to the

“Using IPSU to Set the Access Point’s IP Address and SSID” section on page 3-11 .

3-10

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 3 Configuring the Access Point for the First Time

Using the IP Setup Utility

C I S C O C O N F I D E N T I A L - D r a f t 1

Using IPSU to Set the Access Point’s IP Address and SSID

If you want to change the default IP address (10.0.0.1) of the access point, you can use IPSU. You can also set the access point’s SSID at the same time.

Note IPSU can change the access point’s IP address and SSID only from their default settings. After the IP address and SSID have been changed, IPSU cannot change them again.

Note The computer you use to assign an IP address to the access point must have an IP address in the same subnet as the access point (10.0.0.x).

Follow these steps to assign an IP address and an SSID to the access point:

Step 1

Step 2

Double-click the IPSU icon on your computer desktop to start the utility.

Click the Set Parameters radio button in the Function box (see

Figure 3-5

).

Figure 3-5 IPSU Set Parameters Screen

OL-6226-01

Step 3 Enter the access point’s MAC address in the Device MAC ID field. The access point’s MAC address is printed on the label on the bottom of the unit. It should contain six pairs of hexadecimal digits. Your access point’s MAC address might look like this example:

004096xxxxxx

Note The MAC address field is not case-sensitive.

Step 4

Step 5

Enter the IP address you want to assign to the access point in the IP Address field.

Enter the SSID you want to assign to the access point in the SSID field.

Note You cannot set the SSID without also setting the IP address. However, you can set the IP address without setting the SSID.

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

3-11

Chapter 3 Configuring the Access Point for the First Time

Assigning an IP Address Using the CLI

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 6

Step 7

Click Set Parameters to change the access point’s IP address and SSID settings.

Click Exit to exit IPSU.

Assigning an IP Address Using the CLI

When you connect the access point to the wired LAN, the access point links to the network using a bridge virtual interface (BVI) that it creates automatically. Instead of tracking separate IP addresses for the access point’s Ethernet and radio ports, the network uses the BVI.

When you assign an IP address to the access point using the CLI, you must assign the address to the BVI.

Beginning in privileged EXEC mode, follow these steps to assign an IP address to the access point’s

BVI:

Step 1

Step 2

Step 3

Command configure terminal interface bvi1 ip address address mask

Purpose

Enter global configuration mode.

Enter interface configuration mode for the BVI.

Assign an IP address and address mask to the BVI.

Note If you are connected to the access point using a Telnet session, you lose your connection to the access point when you assign a new IP address to the BVI. If you need to continue configuring the access point using

Telnet, use the new IP address to open another Telnet session to the access point.

Using a Telnet Session to Access the CLI

Follow these steps to browse to access the CLI using a Telnet session. These steps are for a PC running

Microsoft Windows with a Telnet terminal application. Check your PC operating instructions for detailed instructions for your operating system.

Step 1

Step 2

Select Start > Programs > Accessories > Telnet .

If Telnet is not listed in your Accessories menu, select Start > Run , type Telnet in the entry field, and press Enter .

When the Telnet window appears, click Connect and select Remote System .

Note In Windows 2000, the Telnet window does not contain drop-down menus. To start the Telnet session in Windows 2000, type open followed by the access point’s IP address.

Step 3 In the Host Name field, type the access point’s IP address and click Connect .

3-12

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

C H A P T E R

4

Using the Web-Browser Interface

This chapter describes the web-browser interface that you can use to configure the access point. It contains these sections:

Using the Web-Browser Interface for the First Time, page 4-2

Using the Management Pages in the Web-Browser Interface, page 4-2

Using Online Help, page 4-5

The web-browser interface contains management pages that you use to change access point settings, upgrade firmware, and monitor and configure other wireless devices on the network.

Note The access point web-browser interface is fully compatible with Microsoft Internet Explorer

(version 5.x or later) or Netscape Navigator (version 4.x).

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

4-1

Chapter 4 Using the Web-Browser Interface

Using the Web-Browser Interface for the First Time

C I S C O C O N F I D E N T I A L - D r a f t 1

Using the Web-Browser Interface for the First Time

Use the access point’s IP address to browse to the management system. See the

“Obtaining and

Assigning an IP Address” section on page 3-3 for instructions on assigning an IP address to the access

point.

Follow these steps to begin using the web-browser interface:

Step 1

Step 2

Step 3

Step 4

Start your Internet browser.

Enter the access point’s IP address in the browser Location field (Netscape Navigator) or Address field

(Internet Explorer) and press Enter . An Enter Network Password screen appears.

Enter your username in the User Name field. The default username is Cisco.

Enter the access point password in the Password field and press Enter . The default password is Cisco.

The access point Summary Status page appears.

Using the Management Pages in the Web-Browser Interface

The system management pages use consistent techniques to present and save configuration information.

A navigation bar is on the left side of the page, and configuration action buttons appear at the bottom.

You use the navigation bar to browse to other management pages, and you use the configuration action buttons to save or cancel changes to the configuration.

Note Changes are applied only when you click Apply . It’s important to remember that clicking your browser’s

Back button returns you to the previous page without saving any changes you have made. Clicking

Cancel cancels any changes you made on the page and keeps you on that page.

4-2

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 4 Using the Web-Browser Interface

Using the Management Pages in the Web-Browser Interface

C I S C O C O N F I D E N T I A L - D r a f t 1

Figure 4-1 shows the web-browser interface home page.

Figure 4-1 Web-Browser Interface Home Page

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

4-3

Chapter 4 Using the Web-Browser Interface

Using the Management Pages in the Web-Browser Interface

C I S C O C O N F I D E N T I A L - D r a f t 1

Using Action Buttons

Table 4-1 lists the page links and buttons that appear on most management pages.

Table 4-1 Common Buttons on Management Pages

Button/Link

Navigation Links

Home

Description

Express Setup

Express Security

Network Map

Association

Network Interfaces

Security

Services

Wireless Services

System Software

Displays access point status page with information on the number of radio devices associated to the access point, the status of the Ethernet and radio interfaces, and a list of recent access point activity.

Displays the Express Setup page that is used to quickly configure basic access point settings such as system name, IP address, SNMP community, radio roles, and radio activation or deactivation.

Displays the Express Security page that is used to quickly setup basic security settings for both radios such as SSID, VLAN, and the type of security.

Displays a list of infrastructure devices on your wireless LAN.

Displays a list of wireless devices associated to your access point, listing their system names, IP address, MAC address, parent-client relationships, and the

VLAN.

Displays status and statistics for the Ethernet and radio interfaces and provides links to configuration pages for each interface.

Displays a summary of security settings and provides links to security configuration pages that are used to configure all security options for each radio interface.

Displays status for several access point features and links to configuration pages for Telnet/SSH, CDP, domain name server, filters, proxy Mobile IP, QoS, SNMP,

SNTP, and VLANs.

Displays a summary of wireless services used with CCKM and provides links to

WDS configuration pages. .

Displays the version number of the firmware that the access point is running and provides links to configuration pages for upgrading and managing firmware.

Event Log Displays the access point event log and provides links to configuration pages where you can select events to be included in traps, set event severity levels, and set notification methods.

Configuration Action Buttons

Apply

Cancel

Saves changes made on the page and remains on the page.

Discards changes to the page and remains on the page.

Clear

Refresh

Clears the selected options on the page.

Updates status information or statistics displayed on a page.

4-4

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 4 Using the Web-Browser Interface

Using Online Help

C I S C O C O N F I D E N T I A L - D r a f t 1

Character Restrictions in Entry Fields

Because the access point uses Cisco IOS software, there are certain characters that you cannot use in the

entry fields on the web-browser interface. Table 4-2 lists the prohibited characters and the fields in which

you cannot use them.

Table 4-2 Prohibited Characters for Web-Browser Interface Entry Fields

Entry Field Type

Password entry fields

All other entry fields

!

#

;

Prohibited Characters

$

[

?

+

$

[

?

+

You also cannot use these three characters as the first character in an entry field:

Using Online Help

Click the help icon at the top of any page in the web-browser interface to display online help.

Figure 4-2

shows the help and print icons.

Figure 4-2 Print and Help Icons

When a help page appears in a new browser window, use the Select a topic drop-down menu to display the help index or instructions for common configuration tasks, such as configuring VLANs.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

4-5

Using Online Help

Chapter 4 Using the Web-Browser Interface

C I S C O C O N F I D E N T I A L - D r a f t 1

4-6

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

C H A P T E R

5

Using the Command-Line Interface

This chapter describes the IOS command-line interface (CLI) that you can use to configure your access point. It contains these sections:

IOS Command Modes, page 5-2

Getting Help, page 5-3

Abbreviating Commands, page 5-3

Using no and default Forms of Commands, page 5-3

Understanding CLI Messages, page 5-4

Using Command History, page 5-4

Using Editing Features, page 5-5

Searching and Filtering Output of show and more Commands, page 5-8

Accessing the CLI, page 5-8

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

5-1

Chapter 5 Using the Command-Line Interface

IOS Command Modes

C I S C O C O N F I D E N T I A L - D r a f t 1

IOS Command Modes

The Cisco IOS user interface is divided into many different modes. The commands available to you depend on which mode you are currently in. Enter a question mark (?) at the system prompt to obtain a list of commands available for each command mode. Refer to the Cisco IOS Command Reference for

Cisco Aironet Access Points and Bridges for a list of the supported Cisco IOS commands.

When you start a session on the access point, you begin in user mode, often called user EXEC mode .

Only a limited subset of the commands are available in user EXEC mode. For example, most of the user

EXEC commands are one-time commands, such as show commands, which show the current configuration status, and clear commands, which clear counters or interfaces. The user EXEC commands are not saved when the access point reboots.

To have access to all commands, you must enter privileged EXEC mode. Normally, you must enter a password to enter privileged EXEC mode. From this mode, you must enter privileged EXEC mode before you can enter the global configuration mode.

Using the configuration modes (global, interface, and line), you can make changes to the running configuration. If you save the configuration, these commands are stored and used when the access point reboots. To access the various configuration modes, you must start at global configuration mode. From global configuration mode, you can enter interface configuration mode and line configuration mode.

Table 5-1

describes the main command modes, how to access each one, the prompt you see in that mode, and how to exit the mode. The examples in the table use the host name ap .

Table 5-1 Command Mode Summary

Mode

User EXEC

Access Method

Begin a session with your access point.

Prompt ap>

Privileged EXEC While in user EXEC mode, enter the enable command.

ap#

Global configuration While in privileged

EXEC mode, enter the configure command.

Interface configuration

While in global configuration mode, enter the interface command (with a specific interface).

ap(config)# ap(config-if)#

Exit Method

Enter

Enter logout or disable quit .

to exit.

To exit to privileged

EXEC mode, enter exit or end , or press Ctrl-Z .

About This Mode

Use this mode to:

• Change terminal settings

Perform basic tests

Display system information

Use this mode to verify commands. Use a password to protect access to this mode.

Use this mode to configure parameters that apply to the entire access point.

To exit to global configuration mode, enter exit . To return to privileged EXEC mode, press Ctrl-Z or enter end .

Use this mode to configure parameters for the Ethernet and radio interfaces. The

2.4-GHz radio is radio 0, and the 5-GHz radio is radio 1.

5-2

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 5 Using the Command-Line Interface

Getting Help

C I S C O C O N F I D E N T I A L - D r a f t 1

Getting Help

You can enter a question mark (?) at the system prompt to display a list of commands available for each command mode. You can also obtain a list of associated keywords and arguments for any command, as shown in

Table 5-2 .

Table 5-2 Help Summary

Command help abbreviated-command-entry ?

abbreviated-command-entry < Tab >

?

command ?

command keyword ?

Purpose

Obtains a brief description of the help system in any command mode.

Obtains a list of commands that begin with a particular character string.

For example: ap# di?

dir disable disconnect

Completes a partial command name.

For example: ap# sh conf < tab > ap# show configuration

Lists all commands available for a particular command mode.

For example: ap> ?

Lists the associated keywords for a command.

For example: ap> show ?

Lists the associated arguments for a keyword.

For example: ap(config)# cdp holdtime ?

<10-255> Length of time (in sec) that receiver must keep this packet

Abbreviating Commands

You have to enter only enough characters for the access point to recognize the command as unique. This example shows how to enter the show configuration privileged EXEC command: ap# show conf

Using no and default Forms of Commands

Most configuration commands also have a no form. In general, use the no form to disable a feature or function or reverse the action of a command. For example, the no shutdown interface configuration command reverses the shutdown of an interface. Use the command without the keyword no to re-enable a disabled feature or to enable a feature that is disabled by default.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

5-3

Chapter 5 Using the Command-Line Interface

Understanding CLI Messages

C I S C O C O N F I D E N T I A L - D r a f t 1

Configuration commands can also have a default form. The default form of a command returns the command setting to its default. Most commands are disabled by default, so the default form is the same as the no form. However, some commands are enabled by default and have variables set to certain default values. In these cases, the default command enables the command and sets variables to their default values.

Understanding CLI Messages

Table 5-3 lists some error messages that you might encounter while using the CLI to configure your

access point.

Table 5-3 Common CLI Error Messages

Error Message

% Ambiguous command:

"show con"

Meaning

You did not enter enough characters for your access point to recognize the command.

How to Get Help

Re-enter the command followed by a question mark ( ?

) with a space between the command and the question mark.

% Incomplete command.

% Invalid input detected at ‘^’ marker.

You did not enter all the keywords or values required by this command.

The possible keywords that you can enter with the command are displayed.

Re-enter the command followed by a question mark ( ?

) with a space between the command and the question mark.

You entered the command incorrectly. The caret (^) marks the point of the error.

The possible keywords that you can enter with the command are displayed.

Enter a question mark ( ?

) to display all the commands that are available in this command mode.

The possible keywords that you can enter with the command are displayed.

Using Command History

The IOS provides a history or record of commands that you have entered. This feature is particularly useful for recalling long or complex commands or entries, including access lists. You can customize the command history feature to suit your needs as described in these sections:

Changing the Command History Buffer Size, page 5-4

Recalling Commands, page 5-5

Disabling the Command History Feature, page 5-5

Changing the Command History Buffer Size

By default, the access point records ten command lines in its history buffer. Beginning in privileged

EXEC mode, enter this command to change the number of command lines that the access point records during the current terminal session: ap# terminal history

[ size number-of-lines

]

5-4

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 5 Using the Command-Line Interface

Using Editing Features

C I S C O C O N F I D E N T I A L - D r a f t 1

The range is from 0 to 256.

Beginning in line configuration mode, enter this command to configure the number of command lines the access point records for all sessions on a particular line: ap(config-line)# history

[ size number-of-lines

]

The range is from 0 to 256.

Recalling Commands

To recall commands from the history buffer, perform one of the actions listed in

Table 5-4

:

Table 5-4 Recalling Commands

Action

Press

Press

1

Ctrl-P

Ctrl-N

or the up arrow key.

show history

or the down arrow key.

Result

Recall commands in the history buffer, beginning with the most recent command.

Repeat the key sequence to recall successively older commands.

Return to more recent commands in the history buffer after recalling commands with Ctrl-P or the up arrow key. Repeat the key sequence to recall successively more recent commands.

While in privileged EXEC mode, list the last several commands that you just entered. The number of commands that are displayed is determined by the setting of the terminal history global configuration command and history line configuration command.

1.

The arrow keys function only on ANSI-compatible terminals such as VT100s.

Disabling the Command History Feature

The command history feature is automatically enabled.

To disable the feature during the current terminal session, enter the terminal no history privileged

EXEC command.

To disable command history for the line, enter the no history line configuration command.

Using Editing Features

This section describes the editing features that can help you manipulate the command line. It contains these sections:

Enabling and Disabling Editing Features, page 5-6

Editing Commands Through Keystrokes, page 5-6

Editing Command Lines that Wrap, page 5-7

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

5-5

Chapter 5 Using the Command-Line Interface

Using Editing Features

C I S C O C O N F I D E N T I A L - D r a f t 1

Enabling and Disabling Editing Features

Although enhanced editing mode is automatically enabled, you can disable it.

To re-enable the enhanced editing mode for the current terminal session, enter this command in privileged EXEC mode: ap# terminal editing

To reconfigure a specific line to have enhanced editing mode, enter this command in line configuration mode: ap(config-line)# editing

To globally disable enhanced editing mode, enter this command in line configuration mode: ap(config-line)# no editing

Editing Commands Through Keystrokes

Table 5-5 shows the keystrokes that you need to edit command lines.

Table 5-5 Editing Commands Through Keystrokes

Capability

Move around the command line to make changes or corrections.

Recall commands from the buffer and paste them in the command line. The access point provides a buffer with the last ten items that you deleted.

Delete entries if you make a mistake or change your mind.

Keystroke

1

Ctrl-B or the left arrow key

Ctrl-F or the right arrow key

Ctrl-A

Ctrl-E

Esc B

Esc F

Ctrl-T

Ctrl-Y

Esc Y

Delete

Ctrl-D

Ctrl-K

Ctrl-U

Esc D

or

Ctrl-W

or

Backspace

Ctrl-X

Purpose

Move the cursor back one character.

Move the cursor forward one character.

Move the cursor to the beginning of the command line.

Move the cursor to the end of the command line.

Move the cursor back one word.

Move the cursor forward one word.

Transpose the character to the left of the cursor with the character located at the cursor.

Recall the most recent entry in the buffer.

Recall the next buffer entry.

The buffer contains only the last 10 items that you have deleted or cut. If you press Esc Y more than ten times, you cycle to the first buffer entry.

Erase the character to the left of the cursor.

Delete the character at the cursor.

Delete all characters from the cursor to the end of the command line.

Delete all characters from the cursor to the beginning of the command line.

Delete the word to the left of the cursor.

Delete from the cursor to the end of the word.

5-6

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 5 Using the Command-Line Interface

Using Editing Features

C I S C O C O N F I D E N T I A L - D r a f t 1

Table 5-5 Editing Commands Through Keystrokes (continued)

Capability

Capitalize or lowercase words or capitalize a set of letters.

Keystroke

1

Esc C

Esc L

Designate a particular keystroke as an executable command, perhaps as a shortcut.

Scroll down a line or screen on displays that are longer than the terminal screen can display.

Esc U

Ctrl-V or Esc Q

Return

Space

Purpose

Capitalize at the cursor.

Change the word at the cursor to lowercase.

Capitalize letters from the cursor to the end of the word.

Scroll down one line.

Scroll down one screen.

Note The

More

prompt appears for output that has more lines than can be displayed on the terminal screen, including show command output. You can use the Return and

Space bar keystrokes whenever you see the

More prompt.

Redisplay the current command line if the access point suddenly sends a message to your screen.

Ctrl-L or Ctrl-R

1.

The arrow keys function only on ANSI-compatible terminals such as VT100s.

Redisplay the current command line.

Editing Command Lines that Wrap

You can use a wraparound feature for commands that extend beyond a single line on the screen. When the cursor reaches the right margin, the command line shifts ten spaces to the left. You cannot see the first ten characters of the line, but you can scroll back and check the syntax at the beginning of the command.

To scroll back to the beginning of the command entry, press Ctrl-B or the left arrow key repeatedly. You can also press Ctrl-A to immediately move to the beginning of the line.

Note The arrow keys function only on ANSI-compatible terminals such as VT100s.

In this example, the access-list global configuration command entry extends beyond one line. When the cursor first reaches the end of the line, the line is shifted ten spaces to the left and redisplayed. The dollar sign ($) shows that the line has been scrolled to the left. Each time the cursor reaches the end of the line, the line is again shifted ten spaces to the left. ap(config)# access-list 101 permit tcp 131.108.2.5 255.255.255.0 131.108.1

ap(config)# $ 101 permit tcp 131.108.2.5 255.255.255.0 131.108.1.20 255.25

ap(config)# $ t tcp 131.108.2.5 255.255.255.0 131.108.1.20 255.255.255.0 eq ap(config)# $ 108.2.5 255.255.255.0 131.108.1.20 255.255.255.0 eq 45

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

5-7

Chapter 5 Using the Command-Line Interface

Searching and Filtering Output of show and more Commands

C I S C O C O N F I D E N T I A L - D r a f t 1

After you complete the entry, press Ctrl-A to check the complete syntax before pressing the Return key to execute the command. The dollar sign ($) appears at the end of the line to show that the line has been scrolled to the right: ap(config)# access-list 101 permit tcp 131.108.2.5 255.255.255.0 131.108.1

$

The software assumes you have a terminal screen that is 80 columns wide. If you have a width other than that, use the terminal width privileged EXEC command to set the width of your terminal.

Use line wrapping with the command history feature to recall and modify previous complex command entries. For information about recalling previous command entries, see the

“Editing Commands Through

Keystrokes” section on page 5-6 .

Searching and Filtering Output of show and more Commands

You can search and filter the output for show and more commands. This is useful when you need to sort through large amounts of output or if you want to exclude output that you do not need to see.

To use this functionality, enter a show or more command followed by the pipe character (|), one of the keywords begin , include , or exclude , and an expression that you want to search for or filter out: command | { begin | include | exclude } regular-expression

Expressions are case sensitive. For example, if you enter | exclude output , the lines that contain output are not displayed, but the lines that contain Output are displayed.

This example shows how to include in the output display only lines where the expression protocol appears: ap# show interfaces | include protocol

Vlan1 is up, line protocol is up

Vlan10 is up, line protocol is down

GigabitEthernet0/1 is up, line protocol is down

GigabitEthernet0/2 is up, line protocol is up

Accessing the CLI

You can open the access point’s CLI using Telnet or Secure Shell (SSH).

Opening the CLI with Telnet

Follow these steps to open the CLI with Telnet. These steps are for a PC running Microsoft Windows with a Telnet terminal application. Check your PC operating instructions for detailed instructions for your operating system.

Step 1

Step 2

Select Start > Programs > Accessories > Telnet .

If Telnet is not listed in your Accessories menu, select Start > Run , type Telnet in the entry field, and press Enter .

When the Telnet window appears, click Connect and select Remote System .

5-8

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 5 Using the Command-Line Interface

C I S C O C O N F I D E N T I A L - D r a f t 1

Accessing the CLI

Step 3

Step 4

Note In Windows 2000, the Telnet window does not contain drop-down menus. To start the Telnet session in Windows 2000, type open followed by the access point’s IP address.

In the Host Name field, type the access point’s IP address and click Connect .

At the username and password prompts, enter your administrator username and password. The default username is Cisco , and the default password is Cisco . The default enable password is also Cisco .

Usernames and passwords are case-sensitive.

Opening the CLI with Secure Shell

Secure Shell Protocol is a protocol that provides a secure, remote connection to networking devices set up to use it. Secure Shell (SSH) is a software package that provides secure login sessions by encrypting the entire session. SSH features strong cryptographic authentication, strong encryption, and integrity protection. For detailed information on SSH, visit the homepage of SSH Communications Security, Ltd. at this URL: http://www.ssh.com/

SSH provides more security for remote connections than Telnet by providing strong encryption when a device is authenticated. See the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points for detailed instructions on setting up the access point for SSH access.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

5-9

Accessing the CLI

Chapter 5 Using the Command-Line Interface

C I S C O C O N F I D E N T I A L - D r a f t 1

5-10

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

C H A P T E R

6

Troubleshooting

This chapter provides troubleshooting procedures for basic problems with the access point. For the most up-to-date, detailed troubleshooting information, refer to the Cisco TAC website at the following URL

(select Product Support > Wireless > Wireless LAN) : http://www.cisco.com/tac

Sections in this chapter include:

Checking the Access Point LEDs, page 6-2

Checking Basic Settings, page 6-4

Resetting to the Default Configuration, page 6-8

Reloading the Access Point Image, page 6-9

Obtaining the Access Point Image File, page 6-11

Obtaining the TFTP Server Software, page 6-11

Running the Carrier Busy Test, page 6-5

Running the Ping/Link Test, page 6-7

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

6-1

Chapter 6 Troubleshooting

Checking the Access Point LEDs

C I S C O C O N F I D E N T I A L - D r a f t 1

Checking the Access Point LEDs

If your access point is not working properly, check the Status LED on the top panel or the Ethernet and

Radio LEDs in the cable bay area. You can use the LED indications to quickly assess the unit’s status.

Figure 6-1

shows the access point LEDs.

Figure 6-1 Access Point LEDs - TBD

1 Status LED

2 Access point cover

3 Ethernet LED

4 Radio LED

Note To view the Ethernet and Radio LEDs you must open the access point cover (refer to the

“Opening the

Access Point Cover” section on page 2-8

).

The LED signals are listed in Table 6-1 .

Message type

Boot loader status

Table 6-1 LED Signals

Cable Bay Area

Ethernet LED Radio LED

Green

Off

Green

Blinking green

Off

Green

Green

Green

Off

Green

Top of Unit

Status LED

Green

Light Blue Initialize Flash file system.

Pink

Blue

Green

Meaning

DRAM memory test ok.

Flash memory test ok.

Ethernet test ok.

Starting Cisco IOS.

6-2

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 6 Troubleshooting

Checking the Access Point LEDs

C I S C O C O N F I D E N T I A L - D r a f t 1

Message type

Association status

Operating status

Boot loader warnings

Boot loader errors

Cable Bay Area

Ethernet LED Radio LED n/a n/a n/a n/a

Green

Blinking green n/a n/a n/a n/a

Blinking green n/a

Top of Unit

Status LED Meaning

Light green Normal operating condition, but no wireless client devices are associated with the unit.

Sky blue Normal operating condition, at least one wireless client device is associated with the unit.

n/a n/a

Ethernet link is operational.

Transmitting or receiving Ethernet packets.

Off

Red

Off

Off

Blinking green

Red

Off

Off

Amber

Red

Amber

Red

Amber

Off

Off

Off

Off

Off

Red

Red

Amber

Off

Off

Amber

Amber

Amber n/a Transmitting or receiving radio packets.

Blinking dark blue

Yellow

Yellow

Software upgrade in progress

Ethernet link not operational.

Ethernet failure.

Yellow

Yellow

Configuration recovery in progress.

Image recovery

Image recovery in progress Blinking yellow and off

Red

Blinking red and blue

Blinking red and light blue

DRAM memory test failure.

Flash file system failure.

Environment variable (ENVAR) failure .

Blinking red and yellow

Bad MAC address.

Blinking red and off

Ethernet failure during image recovery.

Blinking red and off

Blinking red and off

Boot environment error.

No IOS image file.

Blinking red and off

Boot failure.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

6-3

Checking Basic Settings

Message type

IOS errors

Chapter 6 Troubleshooting

C I S C O C O N F I D E N T I A L - D r a f t 1

Cable Bay Area

Ethernet LED Radio LED n/a Blinking amber n/a

Red

Blinking amber

Red n/a

Blinking green n/a

Blinking green

Top of Unit

Status LED n/a n/a

Orange

Orange

Blinking green

Meaning

Transmit or receive Ethernet errors.

Maximum retries or buffer full occurred on the radio.

Software failure; try disconnecting and reconnecting unit power.

General warning, insufficient inline power.

User activation of location indicator.

Checking Basic Settings

Mismatched basic settings are the most common causes of lost connectivity with wireless clients. If the access point does not communicate with client devices, check the following areas.

SSID

Wireless clients attempting to associate with the access point must use the same SSID as the access point.

If a client device’s SSID does not match the SSID of an access point in radio range, the client device will not associate. The access point default SSID is tsunami .

WEP Keys

The WEP key you use to transmit data must be set up exactly the same on your access point and any wireless devices with which it associates. For example, if you set WEP Key 3 on your client adapter to

0987654321 and select it as the transmit key, you must also set WEP Key 3 on the access point to exactly the same value. The access point does not need to use Key 3 as its transmit key, however.

Refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points for instructions on setting the access point’s WEP keys.

6-4

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 6 Troubleshooting

Low Power Condition

C I S C O C O N F I D E N T I A L - D r a f t 1

Security Settings

Wireless clients attempting to authenticate with your access point must support the same security options configured in the access point, such as EAP or LEAP, MAC address authentication, Message Integrity

Check (MIC), WEP key hashing, and 802.1X protocol versions.

If a wireless client is unable to authenticate with your access point, contact the system administrator for proper security settings in the client adapter and for the client adapter driver and firmware versions that are compatible with the access point settings.

Note The access point MAC address that appears on the Status page in the Aironet Client Utility (ACU) is the

MAC address for the access point radio. The MAC address for the access point Ethernet port is printed on the label on the back of the access point.

Low Power Condition

The access point supports the IEEE 802.3af power standard and the Cisco CDP Power Negotiation protocol for in-line power sources. On power-up if the access point is unable to determine that the power source can supply sufficient power ( TBD watts), the access point automatically deactivates both radios to prevent an over-current condition. The access point also activates a Status LED low power error indication and creates an error log entry (see the

“Checking the Access Point LEDs” section on page 6-2

).

Special instructions goes here: - TBD

Running the Carrier Busy Test

You can use the carrier busy test to determine the least conjested channel for a radio interface (802.11g or 802.11a). You should typically run the test several times over several days to obtain the best results and to avoid temporary activity spikes.

Note The carrier busy test is primarily used for single access points or bridge environments. For sites with multiple access points, a site survey is typically performed to determine the best operation location and operating frequency for the access points.

OL-6226-01

Note All associated clients on the selected radio will be deassociated during the 6 to 8 seconds needed for the carrier busy test.

Perform these steps to activate the carrier busy test:

Step 1

Step 2

Step 3

Step 4

Use your web browser to access the access point browser interface.

Click Network Interfaces and the Network Interface Summary screen appears.

Choose the radio interface experiencing problems by clicking Radio0-802.11G

or Radio1-802.11A

.

The respective radio status page appears.

Click the Carrier Busy Test tab and the Carrier Busy Test screen appears

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

6-5

Chapter 6 Troubleshooting

Running the Carrier Busy Test

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 5 Click Start to begin the carrier busy test.

When the test completes, the results are displayed on the screen. For each of the channel center frequencies, the test produces a value indicating the percentage of time that the channel is busy.

6-6

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 6 Troubleshooting

Running the Ping/Link Test

C I S C O C O N F I D E N T I A L - D r a f t 1

Running the Ping/Link Test

You can use the ping or link test to evaluate the link to and from an associated wireless device. The ping or link test provides two modes of operation: a.

Perform a test using a specified number of packets and then display the test results.

b.

Perform a test that continuously operates until you stop the test and then displays the test results.

Perform these steps to activate the ping or link test:

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Use your web browser to access the access point browser interface.

Click Association and the main association page appears.

Click the MAC address of an associated wireless device and the Statistics page for that device appears.

Click the Ping/Link Test tab and the Ping/Link Test page appears.

If you want to specify the number of packets to use in the test, perform these steps: a.

b.

Enter the desired number of packets in the Number of Packets field

Enter the desired packet size in the Packet Size field.

c.

Click Start .

If you want to use a continuous test, perform these steps: a.

b.

Enter the desired packet size in the Packet Size field.

Click Start to activate the test.

c.

When desired, click Stop to stop the test.

When the test has completed, the test results are displayed at the bottom of the page. You should check for any lost packets that can indicate a possible problem with the wireless link. For best results, you should also perform this test several times.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

6-7

Chapter 6 Troubleshooting

Resetting to the Default Configuration

C I S C O C O N F I D E N T I A L - D r a f t 1

Resetting to the Default Configuration

If you forget the password that allows you to configure the access point, you may need to completely reset the configuration. You can use the MODE button on the access point or the web-browser interface.

Note The following steps reset all configuration settings to factory defaults, including passwords, WEP keys, the IP address, and the SSID.

Using the MODE Button

Follow these steps to delete the current configuration and return all access point settings to the factory defaults using the MODE button:

Step 1

Step 2

Step 3

Step 4

Step 5

Open the access point cover (refer to the

“Opening the Access Point Cover” section on page 2-8 ).

Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.

Press and hold the MODE button while you reconnect power to the access point.

Hold the MODE button approximately 2 to 3 seconds, and release the button.

After the access point reboots, you must reconfigure the access point by using the Web browser interface, the Telnet interface, or IOS commands.

Note The access point is configured with the factory default values including the IP address (set to receive an IP address using DHCP).

Using the Web Browser Interface

Follow these steps to delete the current configuration and return all access point settings to the factory defaults using the web browser interface.

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Open your Internet browser. You must use Microsoft Internet Explorer (version 5.x or later) or Netscape

Navigator (version 4.x).

Enter the access point’s IP address in the browser address line and press Enter . An Enter Network

Password screen appears.

Enter your username in the User Name field.

Enter the access point password in the Password field and press Enter . The Summary Status page appears.

Click System Software and the System Software screen appears.

Click System Configuration and the System Configuration screen appears.

6-8

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 6 Troubleshooting

C I S C O C O N F I D E N T I A L - D r a f t 1

Reloading the Access Point Image

Step 7 Click the Reset to Defaults button.

Note If the access point is configured with a static IP address, the IP address does not change.

Step 8 After the access point reboots, you must reconfigure the access point by using the Web browser interface, the Telnet interface, or IOS commands.

Reloading the Access Point Image

If your access point has a firmware failure, you must reload the complete access point image file using the Web browser interface or by pressing and holding the MODE button for around 30 seconds. You can use the browser interface if the access point firmware is still fully operational and you want to upgrade the firmware image. However, you can use the MODE button when the access point has a corrupt firmware image.

Using the MODE Button

You can use the MODE button on the access point to reload the access point image file from an active

Trivial File Transfer Protocol (TFTP) server on your network or on a PC connected to the access point

Ethernet port.

Note If your access point experiences a firmware failure or a corrupt firmware image, indicated by the Status

LED turning an orange color, you must reload the image from a connected TFTP server.

OL-6226-01

Note This process resets all configuration settings to factory defaults, including passwords, WEP keys, the access point IP address, and SSIDs.

Follow these steps to reload the access point image file:

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

The PC you intend to use must be configured with a static IP address between 10.0.0.2 and 10.0.0.30.

Place a copy of the access point image file (such as c1130-k9w7-tar.122-15.JA.tar) into the TFTP server folder on your PC. For additional information, refer to the

“Obtaining the Access Point Image File”

and

“Obtaining the TFTP Server Software”

sections.

Rename the access point image file in the TFTP server folder to c1130-k9w7-tar.default

.

Activate the TFTP server.

If using in-line power, use a Category 5 (CAT5) Ethernet cable to connect your PC to the To Network

Ethernet connector on the power injector.

Open the access point cover (refer to the

“Opening the Access Point Cover” section on page 2-8 ).

Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.

Press and hold the MODE button while you reconnect power to the access point.

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

6-9

Chapter 6 Troubleshooting

Reloading the Access Point Image

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 9

Step 10

Hold the MODE button approximately 20 to 30 seconds, and release the MODE button.

After the access point reboots, you must reconfigure the access point by using the Web interface, the

Telnet interface, or IOS commands.

Web Browser Interface

You can also use the Web browser interface to reload the access point image file. The Web browser interface supports loading the image file using HTTP or TFTP interfaces.

Note Your access point configuration is not changed when using the browser to reload the image file.

Browser HTTP Interface

The HTTP interface enables you to browse to the access point image file on your PC and download the image to the access point. Follow these instructions to use the HTTP interface:

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Open your Internet browser. You must use Microsoft Internet Explorer (version 5.x or later) or Netscape

Navigator (version 4.x).

Enter the access point’s IP address in the browser address line and press Enter . An Enter Network

Password screen appears.

Enter your username in the User Name field.

Enter the access point password in the Password field and press Enter . The Summary Status page appears.

Click the System Software tab and then click Software Upgrade . The HTTP Upgrade screen appears.

Click the Browse button to locate the access point image file (such as c1130-k9w7-tar.122-15.JA.tar) on your PC.

Click the Upload button.

For additional information, click the Help icon on the Software Upgrade screen.

Browser TFTP Interface

The TFTP interface allows you to use a TFTP server on a network device to load the access point image file. Follow these instructions to use a TFTP server:

Step 1

Step 2

Step 3

Open your Internet browser. You must use Microsoft Internet Explorer (version 5.x or later) or Netscape

Navigator (version 4.x).

Enter the access point’s IP address in the browser address line and press Enter . An Enter Network

Password screen appears.

Enter your username in the User Name field.

6-10

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Chapter 6 Troubleshooting

Obtaining the Access Point Image File

C I S C O C O N F I D E N T I A L - D r a f t 1

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Enter the access point password in the Password field and press Enter . The Summary Status page appears.

Click the System Software tab and then click Software Upgrade . The HTTP Upgrade screen appears.

Click the TFTP Upgrade tab.

Enter the IP address for the TFTP server in the TFTP Server field.

Enter the file name for the access point image file (such as c1130-k9w7-tar.122-15.JA.tar) in the Upload

New System Image Tar File field. If the file is located in a subdirectory of the TFTP server root directory, include the relative path of the TFTP server root directory with the filename. If the file is located in the

TFTP root directory, enter only the filename.

Click the Upload button.

When a message appears that indicates the upgrade is complete, click OK .

For additional information click the Help icon on the Software Upgrade screen.

Obtaining the Access Point Image File

The access point image file can be obtained from the Cisco.com software center using these steps:

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Use your Internet browser to access the Cisco Software Center at the following URL: http://www.cisco.com/public/sw-center/sw-wireless.shtml

Click Option 2: Aironet Wireless Software Display Tables .

Find the access point firmware and utilities section and click Cisco Aironet 1130 Series (Cisco IOS

Software) .

Click on the access point image file, such as c1130-k9w7-tar.122-15.JA.tar.

On the Encryption Authorization Form, enter the requested information, read the encryption information, and check the boxes that apply.

Click Submit .

Read and accept the terms and conditions of the Software License Agreement.

Select the image file again to download it.

Download and save the image file to your hard drive and then exit the Internet browser.

Obtaining the TFTP Server Software

You can download TFTP server software from several web sites. Cisco recommends the shareware TFTP utility available at this URL: http://tftpd32.jounin.net

Follow the instructions on the website for installing and using the utility.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

6-11

Obtaining the TFTP Server Software

C I S C O C O N F I D E N T I A L - D r a f t 1

Chapter 6 Troubleshooting

6-12

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

A P P E N D I X

A

Translated Safety Warnings

This appendix provides translations of the safety warnings that appear in this publication. These translated warnings apply to other documents in which they appear in English. The following safety warnings appear in this appendix:

Statement 245B—Explosive Device Proximity Warning, page A-2

Statement 332—Antenna Installation Warning, page A-3

Statement 1001—Work During Lightning Activity Warning, page A-4

Statement 1004—Installation Instructions Warning, page A-5

Statement 1005—Circuit Breaker (15A) Warning, page A-6

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

A-1

Appendix A Translated Safety Warnings

Statement 245B—Explosive Device Proximity Warning

C I S C O C O N F I D E N T I A L - D r a f t 1

Statement 245B—Explosive Device Proximity Warning

Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.

Statement 245B

Waarschuwing Gebruik dit draadloos netwerkapparaat alleen in de buurt van onbeschermde ontstekers of in een omgeving met explosieven indien het apparaat speciaal is aangepast om aan de eisen voor een dergelijk gebruik te voldoen.

Varoitus

Attention

Warnung

Avvertenza

Advarsel

Älä käytä johdotonta verkkolaitetta suojaamattomien räjäytysnallien läheisyydessä tai räjäytysalueella, jos laitetta ei ole erityisesti muunnettu sopivaksi sellaiseen käyttöön.

Ne jamais utiliser un équipement de réseau sans fil à proximité d'un détonateur non blindé ou dans un lieu présentant des risques d'explosion, sauf si l'équipement a été modifié à cet effet.

Benutzen Sie Ihr drahtloses Netzwerkgerät nicht in der Nähe ungeschützter Sprengkapseln oder anderer explosiver Stoffe, es sei denn, Ihr Gerät wurde eigens für diesen Gebrauch modifiziert und bestimmt.

Non utilizzare la periferica di rete senza fili in prossimità di un detonatore non protetto o di esplosivi a meno che la periferica non sia stata modificata a tale proposito.

Ikke bruk den trådløse nettverksenheten nært inntil uisolerte fenghetter eller i et eksplosivt miljø med mindre enheten er modifisert slik at den tåler slik bruk.

Aviso

¡Advertencia!

Varning!

Não opere o dispositivo de rede sem fios perto de cápsulas explosivas não protegidas ou num ambiente explosivo, a não ser que o dispositivo tenha sido modificado para se qualificar especialmente para essa utilização.

No utilizar un aparato de la red sin cable cerca de un detonador que no esté protegido ni tampoco en un entorno explosivo a menos que el aparato haya sido modificado con ese fin.

Använd inte den trådlösa nätverksenheten i närheten av oskyddade tändhattar eller i en explosiv miljö om inte enheten modifierats för att kunna användas i sådana sammanhang.

A-2

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Appendix A Translated Safety Warnings

Statement 332—Antenna Installation Warning

C I S C O C O N F I D E N T I A L - D r a f t 1

Statement 332—Antenna Installation Warning

Warning In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons. Statement 332

Waarschuwing

Varoitus

Om te voldoen aan de FCC radiofrequentie (RF) blootstellingslimieten dienen antennes zich minstens

20 cm of meer van de lichamen van alle personen bevinden.

FCC:n antamien radiotaajuuksille altistumista koskevien rajoitusten mukaan antennien on sijaittava vähintään 20 cm:n päässä kaikista henkilöistä.

Attention

Warnung

Avvertenza

Pour se conformer aux limites d'exposition à la fréquence radio préconisées par la FCC (Federal

Communications Commission), les antennes doivent se situer à un minimum de 20 cm de toute personne.

Um die in den FCC-Richtlinien festgelegten Expositionshöchstgrenzen für Radiofrequenzen (RF) nicht zu überschreiten, sollten Antennen mindestens 20 cm entfernt von Personen aufgestellt werden.

Per conformarsi ai limiti FCC di esposizione a radiofrequenza (RF), le antenne devono stare ad una distanza minima di 20 cm dal corpo di ogni persona.

Advarsel

Aviso

¡Advertencia!

Varning!

I henhold til eksponeringsgrensene for radiofrekvenser (RF), skal antenner befinne seg på en avstand av minst 20 cm eller mer fra mennesker.

Para estar de acordo com as normas FCC de limites de exposição para freqüência de rádio (RF), as antenas devem estar distantes no mínimo 20 cm (7,9 pol) do corpo de qualquer pessoa.

Para cumplir con los límites de exposición de radio frecuencia (RF) de la Comisión Federal de

Comunicaciones (FCC) es preciso ubicar las antenas a un mínimo de 20 cm (7,9 pulgadas) o más del cuerpo de las personas.

För att följa FCC-exponeringsgränserna för radiofrekvens (RF), bör antenner placeras på minst 20 cm avstånd från alla människor.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

A-3

Appendix A Translated Safety Warnings

Statement 1001—Work During Lightning Activity Warning

C I S C O C O N F I D E N T I A L - D r a f t 1

Statement 1001—Work During Lightning Activity Warning

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Waarschuwing

Varoitus

Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan te sluiten of te ontkoppelen.

Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota kaapeleita ukkosilmalla.

Attention

Warnung

Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant un orage.

Arbeiten Sie nicht am System und schließen Sie keine Kabel an bzw. trennen Sie keine ab, wenn es gewittert.

Avvertenza

Advarsel

Aviso

¡Advertencia!

Varning!

Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con fulmini.

Utfør aldri arbeid på systemet, eller koble kabler til eller fra systemet når det tordner eller lyner.

Não trabalhe no sistema ou ligue e desligue cabos durante períodos de mau tempo (trovoada).

No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas eléctricas en la atmósfera.

Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller koppla loss kablar.

A-4

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Appendix A Translated Safety Warnings

Statement 1004—Installation Instructions Warning

C I S C O C O N F I D E N T I A L - D r a f t 1

Statement 1004—Installation Instructions Warning

Warning

Waarschuwing

Read the installation instructions before connecting the system to the power source. Statement 1004

Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.

Varoitus

Attention

Warnung

Avvertenza

Advarsel

Aviso

¡Advertencia!

Varning!

Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.

Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.

Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen.

Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.

Les installasjonsinstruksjonene før systemet kobles til strømkilden.

Leia as instruções de instalação antes de ligar o sistema à fonte de energia.

Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.

Läs installationsanvisningarna innan du kopplar systemet till strömförsörjningsenheten.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

A-5

Appendix A Translated Safety Warnings

Statement 1005—Circuit Breaker (15A) Warning

C I S C O C O N F I D E N T I A L - D r a f t 1

Statement 1005—Circuit Breaker (15A) Warning

Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than:

15A Statement 1005

Waarschuwing

Varoitus

Dit product is afhankelijk van de installatie van het gebouw voor beveiliging tegen kortsluiting

(overstroom). Controleer of de beschermingsinrichting niet meer dan:

15A is.

Tämä tuote on riippuvainen rakennukseen asennetusta oikosulkusuojauksesta

(ylivirtasuojauksesta). Varmista, että suojalaitteen mitoitus ei ole yli:

15A

Attention

Warnung

Avvertenza

Advarsel

Aviso

¡Advertencia!

Varning!

Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de l'installation électrique du local. Vérifiez que le courant nominal du dispositif de protection n'est pas supérieur à :

15A

Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung nicht mehr als:

15A beträgt.

Questo prodotto dipende dall'impianto dell'edificio per quanto riguarda la protezione contro cortocircuiti (sovracorrente). Assicurarsi che il dispositivo di protezione non abbia un rating superiore a:

15A

Dette produktet er avhengig av bygningens installasjoner av kortslutnings (overstrøm)-beskyttelse.

Påse at verneenheten ikke er merket høyere enn:

15A

Este produto depende das instalações existentes para proteção contra curto-circuito (sobrecarga).

Assegure-se de que o fusível ou disjuntor não seja superior a:

15A

Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del edificio. Asegúrese de que el dispositivo de protección no sea superior a:

15A

Denna produkt är beroende av i byggnaden installerat kortslutningsskydd (överströmsskydd).

Kontrollera att skyddsanordningen inte har högre märkvärde än:

15A

15A

A-6

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Appendix A Translated Safety Warnings

Statement 1005—Circuit Breaker (15A) Warning

C I S C O C O N F I D E N T I A L - D r a f t 1

15A

15A

15A

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

A-7

Appendix A Translated Safety Warnings

Statement 1005—Circuit Breaker (15A) Warning

C I S C O C O N F I D E N T I A L - D r a f t 1

A-8

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

A P P E N D I X

B

Declarations of Conformity and Regulatory

Information

This appendix provides declarations of conformity and regulatory information for the Cisco Aironet

1130 Series Access Points.

This appendix contains the following sections:

Manufacturers Federal Communication Commission Declaration of Conformity Statement

Department of Communications—Canada

European Community, Switzerland, Norway, Iceland, and Liechtenstein

Declaration of Conformity for RF Exposure

Guidelines for Operating Cisco Aironet Access Points in Japan

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

B-1

Appendix B Declarations of Conformity and Regulatory Information

Manufacturers Federal Communication Commission Declaration of Conformity Statement

C I S C O C O N F I D E N T I A L - D r a f t 1

Manufacturers Federal Communication Commission

Declaration of Conformity Statement

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

Model:

AIR-AP1131AG-A-K9

FCC Certification number:

LDK102054

Manufacturer:

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

This device complies with Part 15 rules. Operation is subject to the following two conditions:

1.

This device may not cause harmful interference, and

2.

This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase separation between the equipment and receiver.

Connect the equipment to an outlet on a circuit different from which the receiver is connected.

Consult the dealer or an experienced radio/TV technician.

Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device.

Caution Within the 5.15 to 5.25 GHz band (5 GHz radio channels 34 to 48) the U-NII devices are restricted to indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite System

(MSS) operations.

B-2

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Appendix B Declarations of Conformity and Regulatory Information

Department of Communications—Canada

C I S C O C O N F I D E N T I A L - D r a f t 1

Department of Communications—Canada

Model:

AIR-AP1131AG-A-K9

Certification number:

2461B-102054

Canadian Compliance Statement

This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du

Canada.

This device complies with Class B Limits of Industry Canada. Operation is subject to the following two conditions:

1.

This device may not cause harmful interference, and

2.

This device must accept any interference received, including interference that may cause undesired operation.

Cisco Aironet 2.4-GHz Access Points are certified to the requirements of RSS-210 for 2.4-GHz spread spectrum devices, and Cisco Aironet 54-Mbps, 5-GHz Access Points are certified to the requirements of

RSS-210 for 5-GHz spread spectrum devices.The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office.

European Community, Switzerland, Norway, Iceland, and

Liechtenstein

Model:

AIR-AP1131AG-E-K9

Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC

English:

Deutsch:

Dansk:

This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprecheneden Vorgaben der Richtlinie 1999/5/EU.

Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Directiv 1999/5/EF.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

B-3

Appendix B Declarations of Conformity and Regulatory Information

European Community, Switzerland, Norway, Iceland, and Liechtenstein

C I S C O C O N F I D E N T I A L - D r a f t 1

Español:

Έλληνας

Français:

Íslenska:

Italiano:

Svenska:

:

Nederlands:

Norsk:

Português:

Suomalainen:

Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directive 1999/5/EC.

Αυτός ο εξοπλισ µ ός συ µµ ορφώνεται µ ε τις ουσιώδεις απαιτήσεις και τις λοιπές

διατάξεις της Οδηγίας 1999/5/E Κ .

Cet appareil est conforme aux exigencies essentialles et aux autres dispositions pertinantes de la Directive 1999/5/EC.

Þessi búnaður samrýmist lögboðnum kröfum og öðrum ákvæðum tilskipunar

1999/5/ESB.

Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla

Direttiva 1999/5/EC.

Deze apparatuur voldoet aan de belangrijkste eisen en andere voorzieningen van richtlijn 1999/5/EC.

Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-directiv 1999/5/EC.

Este equipamento satisfaz os requisitos essenciais e outras provisões da Directiva

1999/5/EC.

Tämä laite täyttää direktiivin 1999/5/EY oleelliset vaatimukset ja on siinä asetettujen muidenkin ehtojen mukainen.

Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i Direktiv 1999/5/EC.

For 2.4 GHz radios, the following standards were applied:

Radio:

EMC:

Safety:

EN 300.328-1, EN 300.328-2

EN 301.489-1, EN 301.489-17

EN 60950

Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate

Compliance.

For 54 Mbps, 5 GHz access points, the following standards were applied:

Radio:

EMC:

Safety:

EN 301.893

EN 301.489-1, EN 301.489-17

EN 60950

B-4

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Appendix B Declarations of Conformity and Regulatory Information

Declaration of Conformity for RF Exposure

C I S C O C O N F I D E N T I A L - D r a f t 1

The following CE mark is affixed to the access point with a 2.4 GHz radio and a 54 Mbps, 5 GHz radio:

Declaration of Conformity for RF Exposure

The radio has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, and

15.247 (b) (4) addressing RF Exposure from radio frequency devices as defined in Evaluating

Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. The equipment shoud be installed more than 20 cm (7.9 in.) from your body or nearby persons.

The access point must be installed to maintain a minimum 20 cm (7.9 in.) co-located separation distance from other FCC approved indoor/outdoor antennas used with the access point. Any antennas or transmitters not approved by the FCC cannot be co-located with the access point. The access point’s co-located 2.4 GHz and 5 GHz integrated antennas support a minimum separation distance of

8 cm (3.2 in.) and are compliant with the applicable FCC RF exposure limit when transmitting simultaneously.

Note Dual antennas used for diversity operation are not considered co-located.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

B-5

Appendix B Declarations of Conformity and Regulatory Information

Guidelines for Operating Cisco Aironet Access Points in Japan

C I S C O C O N F I D E N T I A L - D r a f t 1

Guidelines for Operating Cisco Aironet Access Points in Japan

This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English.

Model:

AIR-AP1131AG-J-K9

Japanese Translation

03-5549-6500

English Translation

This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines.

1.

Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity.

2.

3.

If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions.

If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below.

Contact Number: 03-5549-6500

B-6

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Appendix B Declarations of Conformity and Regulatory Information

Declaration of Conformity Statements

C I S C O C O N F I D E N T I A L - D r a f t 1

Declaration of Conformity Statements

All the Declaration of Conformity statements related to this product can be found at the following URL: http://www.ciscofax.com

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

B-7

Appendix B Declarations of Conformity and Regulatory Information

Declaration of Conformity Statements

C I S C O C O N F I D E N T I A L - D r a f t 1

B-8

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

A P P E N D I X

C

Access Point Specifications

This appendix provides technical specifications for the Cisco Aironet 1130AG Series Access Point.

Table C-1 lists the technical specifications for the access point.

Table C-1 Access Point Specifications

Category

Size

Indicators

Connectors

802.11b Radio Specifications 802.11g Radio Specifications

7.53 in. W x 7.53 in. D x 1.31 in. H

19.13 cm W x 19.13 cm D x 3.33 cm H

802.11a Radio Specifications

Tri-color Status LED indicator on the top panel and two bi-color LED indicators (radio and Ethernet) in the cable bay

Cable bay (left to right)

Input Voltage

Input Power

Power connector (for plug-in AC power module); RJ-45 connector for 10BASE-T or

100BASE-T Ethernet connections; upside down RJ-45 connector for serial connections.

48 VDC (nominal)

12.95 W (typical)

Operating Temperature Base unit:

32 to 104 o

F (0 to 40 o

C)

1130 series power injector:

32 to 104 o

F (0 to 40 o

C)

1130 series power module:

32 to 104 o

F (0 to 40 o

C)

Storage Temperature TBD to TBD o F (TBD to TBD o C )

Weight Without mounting hardware:

1.48 lbs (0.67 kg)

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

C-1 OL-6226-01

Appendix C Access Point Specifications

C I S C O C O N F I D E N T I A L - D r a f t 1

Table C-1 Access Point Specifications (continued)

Category

Power Output

802.11b Radio Specifications 802.11g Radio Specifications

100 mW (20 dBm)

50 mW (17 dBm)

25 mW (14 dBm)

10 mW (11 dBm)

5 mW (8 dBm)

3 mW (5 dBm)

1 mW (2 dBm)

0.5 mW (-1 dBm)

(Depending on the regulatory domain in which the access point is installed)

50 mW (17 dBm)

25 mW (14 dBm)

10 mW (11 dBm)

5 mW (8 dBm)

3 mW (5 dBm)

1 mW (2 dBm)

0.5 mW (-1 dBm)

802.11a Radio Specifications

50 mW (17 dBm)

30 mW (15 dBm)

25 mW (14 dBm)

10 mW (11 dBm)

5 mW (8 dBm)

3 mW (5 dBm)

1 mW (2 dBm)

0.5 mW (-1 dBm)

(Depending on the regulatory domain in which the access point is installed)

(Depending on the regulatory domain in which the access point is installed)

Antenna

Frequency

A diversity system with two integrated 4-dBi antennas.

2.400 to 2.497 GHz

(Depending on the regulatory domain in which the access point is installed)

A diversity system with two integrated 4-dBi antennas.

5.15 to 5.25 GHz

5.25 to 5.35 GHz

5.725 to 5.85 GHz

(Depending on the regulatory domain in which the access point is installed)

Orthogonal Frequency Division Multiplex (OFDM) Modulation Complementary Code Keying

(CCK)

Subcarrier modulation BPSK (1 Mbps)

QPSK (2 Mbps)

CCK (5.5 and 11 Mbps)

BPSK (6 and 9 Mbps)

QPSK (12 and 18 Mbps)

16-QAM (24 and 36 Mbps)

64-QAM (48 and 54 Mbps)

BPSK (6 Mbps and 9 Mbps)

QPSK (12 Mbps and 18 Mbps)

16-QAM (24 and 36 Mbps)

64-QAM (48 and 54 Mbps)

Data rates

Typical indoor range

Compliance

1, 2, 5.5, and 11 Mbps

320 ft at 1 Mbps

130 ft at 11 Mbps

6, 9, 12, 18, 24, 36, 48, and 54 Mbps

170 ft at 6 Mbps

80 ft at 54 Mbps

175 ft at 6 Mbps

50 ft at 54 Mbps

Complies with UL 2043 for products installed in a building’s environmental air handling spaces, such as above suspended ceilings.

Note For performance reasons, Cisco recommends that the access point not be placed above a suspended ceiling.

Caution The Cisco Aironet power injectors and power modules are not tested to UL 2043 and should not be placed in a building’s environmental air space, such as above suspended ceilings.

C-2

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Appendix C Access Point Specifications

C I S C O C O N F I D E N T I A L - D r a f t 1

Table C-1 Access Point Specifications (continued)

Category

Safety

802.11b Radio Specifications 802.11g Radio Specifications

Designed to meet:

802.11a Radio Specifications

CSN/CSA 22.2 No. 60950

UL 2043 (Plenum rating)

UL 60950 Third Edition

IEC 60950 Second Edition, including Amendments 1-4 with all deviations •

• EN 60950 Second Edition, including Amendments 1-4

Radio Approvals FCC Parts 15.247

Canada RSS-210

Japan ARIB-STD-33B

Japan ARIB-STD-66

Europe EN-300.328

EMI and Susceptibility FCC Part 15.107 and 15.109 Class B

ICES-003 Class B (Canada)

EN 55022 B

AS/NZS 3548 Class B

VCCI Class B

EN 301.489-1

EN 301.489-17

RF Exposure OET-65C

RSS-102

ANSI C95.1

FCC Part 15.407

Canada RSS-210

Japan ARIB STD-T71

EN 301.893

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

C-3

Appendix C Access Point Specifications

C I S C O C O N F I D E N T I A L - D r a f t 1

C-4

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

A P P E N D I X

D

Channels and Power Levels

This appendix lists the IEEE 802.11b/g (2.4-GHz) and the IEEE 802.11a (5-GHz) channels and maximum power levels supported by the world’s regulatory domains.

The following topic is covered in this appendix:

Channels and Maximum Power Levels, page D-2

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

D-1

Appendix D Channels and Power Levels

Channels and Maximum Power Levels

C I S C O C O N F I D E N T I A L - D r a f t 1

Channels and Maximum Power Levels

IEEE 802.11b/g (2.4-GHz Band)

An improper combination of power level and antenna gain can result in equivalent isotropic radiated power (EIRP) above the amount allowed per regulatory domain.

Table D-1 indicates the channel

identifiers, channel center frequencies, and maximum power levels for each channel allowed by the regulatory domains:

.

Table D-1 Channels and Maximum Conducted Power for the 802.11b/g Radio

12

13

14

8

9

10

11

Channel

Identifier

1

4

5

2

3

6

7

2447

2452

2457

2462

2467

2472

2484

Center

Frequency

(MHz)

2412

2417

2422

2427

2432

2437

2442

20

20

20

20

20

20

20

20

Maximum Conducted Power Levels (dBm) in the Regulatory Domains

Americas

(– A)

CCK OFDM CCK

China

(–C)

OFDM CCK

EMEA

(– E)

OFDM CCK

Japan

(–J)

OFDM

North American

(– N)

CCK OFDM

20

20

20

17

17

17

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

20

20

20

17

17

17

17

17

17

17

17

17

17

17

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

14

20

20

20

20

20

20

20

20

17

17

17

17

17

17

17

17

D-2

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Appendix D Channels and Power Levels

Channels and Maximum Power Levels

C I S C O C O N F I D E N T I A L - D r a f t 1

.

IEEE 802.11a (5-GHz Band)

An improper combination of power level and antenna gain can result in equivalent isotropic radiated power (EIRP) above the amount allowed per regulatory domain. All channel sets are restricted to indoor usage except the Americas (–A), which allows for indoor and outdoor use on channels 52 through 64 in the United States.

Table D-2 indicates the channel identifiers, channel center frequencies, and maximum power levels for

each IEEE 802.11a 20-MHz-wide channel allowed by the regulatory domains:

Table D-2 Channels for IEEE 802.11a Radio

Channel

Identifier

34

36

38

40

42

44

46

48

149

153

157

161

165

52

56

60

64

Center

Frequency

(MHz)

Maximum Conducted Power Levels (dBm) in the Regulatory Domains

Americas

(– A)

China

(–C)

EMEA

(– E)

UNII-1 (5150-5250 MHz)

Japan

(–J)

North America

(– N)

5170 –

5180 15

5190 –

5200 15

5210 –

5220 15

5230 –

5240 15

17

17

17

15

15

15

15

15

15

15

15

5260 17

5280 17

5300 17

5320 17

5745

5765

17

17

UNII-2 (5250-5350 MHz)

17

17

17

17

17

UNII-3 (5725-5850 MHz)

17 –

17

17

17

17

17

17

5785

5805

5825

17

17

17

17

17

17

17

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

D-3

Appendix D Channels and Power Levels

Channels and Maximum Power Levels

C I S C O C O N F I D E N T I A L - D r a f t 1

D-4

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

A P P E N D I X

E

Console Cable Pinouts

This appendix identifies the pinouts for the serial console cable that connects to the access point’s serial console port. The appendix contains the following sections:

Overview, page E-2

Console Port Signals and Pinouts, page E-2

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

E-1

Overview

C I S C O C O N F I D E N T I A L - D r a f t 1

Appendix E Console Cable Pinouts

Overview

The access point requires a special serial cable that connects the access point serial console port (RJ-45 connector) to your PC’s COM port (DB-9 connector). This cable can be purchased from Cisco (part number AIR-CONCAB1200) or can be built using the pinouts in this appendix.

Console Port Signals and Pinouts

Use the console RJ-45 to DB-9 serial cable to connect the access point’s console port to the COM port of your PC running a terminal emulation program.

Note Both the Ethernet and console ports use RJ-45 connectors. Be careful to avoid accidently connecting the serial cable to the Ethernet port connector.

Table E-1

lists the signals and pinouts for the console RJ-45 to DB-9 serial cable.

Table E-1 Signals and Pinouts for a Console RJ-45 to DB-9 Serial Cable

6

7

8

3

4

5

1

2

Console Port

RJ-45

Pins Signals

1, 2, 3, 4

NC

NC

TXD

GND

GND

RXD

NC

NC

1.

NC indicates not connected.

2.

TXD indicates transmit data.

3.

GND indicates ground.

4.

RXD indicates receive data.

3

2

5

5

PC COM Port

DB-9

Pins Signals

1, 2, 3, 4

RXD

GND

GND

TXD

E-2

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

G L O S S A R Y

802.11

802.11a

802.11b

802.11g

The IEEE standard that specifies carrier sense media access control and physical layer specifications for 1- and 2-megabit-per-second (Mbps) wireless LANs operating in the 2.4-GHz band.

The IEEE standard that specifies carrier sense media access control and physical layer specifications for wireless LANs operating in the 5-GHz frequency band.

The IEEE standard that specifies carrier sense media access control and physical layer specifications for 5.5- and 11-Mbps wireless LANs operating in the

2.4-GHz frequency band.

The IEEE standard that specifies carrier sense media access control and physical layer specifications for 6, 9, 12, 18, 24, 36, 48, and 54 Mbps wireless LANs operating in the 2.4-GHz frequency band.

A access point ad hoc network antenna gain associated

A wireless LAN data transceiver that uses radio waves to connect a wired network with wireless stations.

A wireless network composed of stations without Access Points.

The gain of an antenna is a measure of the antenna’s ability to direct or focus radio energy over a region of space. High gain antennas have a more focused radiation pattern in a specific direction.

A station is configured properly to allow it to wirelessly communicate with an

Access Point.

B beacon

BOOTP

A wireless LAN packet that signals the availability and presence of the wireless device. Beacon packets are sent by access points and base stations; however, client radio cards send beacons when operating in computer to computer (Ad

Hoc) mode.

Boot Protocol. A protocol used for the static assignment of IP addresses to devices on the network.

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

GL-1

C

CCK cell

Glossary

C I S C O C O N F I D E N T I A L - D r a f t 1

BPSK broadcast packet

A modulation technique used by IEEE 802.11b-compliant wireless LANs for transmission at 1 Mbps.

A single data message (packet) sent to all addresses on the same subnet.

client

CSMA

Complementary code keying. A modulation technique used by IEEE

802.11b-compliant wireless LANs for transmission at 5.5 and 11 Mbps.

The area of radio range or coverage in which the wireless devices can communicate with the base station. The size of the cell depends upon the speed of the transmission, the type of antenna used, and the physical environment, as well as other factors.

A radio device that uses the services of an Access Point to communicate wirelessly with other devices on a local area network.

Carrier sense multiple access. A wireless LAN media access method specified by the IEEE 802.11 specification.

D data rates dBi

DHCP dipole

Domain Name

DNS

DSSS

The range of data transmission rates supported by a device. Data rates are measured in megabits per second (Mbps).

A ratio of decibels to an isotropic antenna that is commonly used to measure antenna gain. The greater the dBi value, the higher the gain, and the more acute the angle of coverage.

Dynamic host configuration protocol. A protocol available with many operating systems that automatically issues IP addresses within a specified range to devices on the network. The device retains the assigned address for a specific administrator-defined period.

A type of low-gain (2.2-dBi) antenna consisting of two (often internal) elements.

The text name that refers to a grouping of networks or network resources based on organization-type or geography; for example: name.com—commercial; name.edu—educational; name.gov—government; ISPname.net—network provider (such as an ISP); name.ar—Argentina; name.au—Australia; and so on.

Domain Name System server. A server that translates text names into IP addresses. The server maintains a database of host alphanumeric names and their corresponding IP addresses.

Direct sequence spread spectrum. A type of spread spectrum radio transmission that spreads its signal continuously over a wide frequency band.

GL-2

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

E

EAP

Ethernet

Extensible Authentication Protocol. An optional IEEE 802.1x security feature ideal for organizations with a large user base and access to an EAP-enabled

Remote Authentication Dial-In User Service (RADIUS) server.

The most widely used wired local area network. Ethernet uses carrier sense multiple access (CSMA) to allow computers to share a network and operates at

10, 100, or 1000 Mbps, depending on the physical layer used.

F file server firmware

G gateway

GHz

A repository for files so that a local area network can share files, mail, and programs.

Software that is programmed on a memory chip.

A device that connects two otherwise incompatible networks together.

Gigahertz. One billion cycles per second. A unit of measure for frequency.

I

IEEE infrastructure

IP Address

IP subnet mask isotropic

Institute of Electrical and Electronic Engineers. A professional society serving electrical engineers through its publications, conferences, and standards development activities. The body responsible for the Ethernet 802.3 and wireless

LAN 802.11 specifications.

The wired Ethernet network.

The Internet Protocol (IP) address of a station.

The number used to identify the IP subnetwork, indicating whether the IP address can be recognized on the LAN or if it must be reached through a gateway. This number is expressed in a form similar to an IP address; for example: 255.255.255.0.

An antenna that radiates its signal in a spherical pattern.

Glossary

OL-6226-01

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

GL-3

Glossary

C I S C O C O N F I D E N T I A L - D r a f t 1

M

MAC modulation multipath multicast packet

Media Access Control address. A unique 48-bit number used in Ethernet data packets to identify an Ethernet device, such as an access point or your client adapter.

Any of several techniques for combining user information with a transmitter’s carrier signal.

The echoes created as a radio signal bounces off of physical objects.

A single data message (packet) sent to multiple addresses.

O omni-directional This typically refers to a primarily circular antenna radiation pattern.

Orthogonal

Frequency Division

Multiplex (OFDM)

A modulation technique used by IEEE 802.11a-compliant wireless LANs for transmission at 6, 9, 12, 18, 24, 36, 48, and 54 Mbps.

P packet A basic message unit for communication across a network. A packet usually includes routing information, data, and sometimes error detection information.

Q

Quadruple Phase

Shift Keying A modulation technique used by IEEE 802.11b-compliant wireless LANs for transmission at 2 Mbps.

R range receiver sensitivity

RF

A linear measure of the distance that a transmitter can send a signal.

A measurement of the weakest signal a receiver can receive and still correctly translate it into data.

Radio frequency. A generic term for radio-based technology.

GL-4

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

Glossary roaming

RP-TNC

C I S C O C O N F I D E N T I A L - D r a f t 1

A feature of some Access Points that allows users to move through a facility while maintaining an unbroken connection to the LAN.

A connector type unique to Cisco Aironet radios and antennas. Part 15.203 of the FCC rules covering spread spectrum devices limits the types of antennas that may be used with transmission equipment. In compliance with this rule, Cisco

Aironet, like all other wireless LAN providers, equips its radios and antennas with a unique connector to prevent attachment of non-approved antennas to radios.

S spread spectrum

SSID

A radio transmission technology that spreads the user information over a much wider bandwidth than otherwise required in order to gain benefits such as improved interference tolerance and unlicensed operation.

Service Set Identifier (also referred to as Radio Network Name). A unique identifier used to identify a radio network and which stations must use to be able to communicate with each other or to an access point. The SSID can be any alphanumeric entry up to a maximum of 32 characters.

T transmit power The power level of radio transmission.

U

UNII

UNII-1

UNII-2

UNII-3 unicast packet

W

WEP

Unlicensed National Information Infrastructure—regulations for UNII devices operating in the 5.15 to 5.35 GHz and 5.725 to 5.825 GHz frequency bands.

Regulations for UNII devices operating in the 5.15 to 5.25 GHz frequency band.

Regulations for UNII devices operating in the 5.25 to 5.35 GHz frequency band.

Regulations for UNII devices operating in the 5.725 to 5.825 GHz frequency band.

A single data message (packet) sent to a specific IP address.

workstation

OL-6226-01

Wired Equivalent Privacy. An optional security mechanism defined within the

802.11 standard designed to make the link integrity of wireless devices equal to that of a cable.

A computing device with an installed client adapter.

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

GL-5

Glossary

C I S C O C O N F I D E N T I A L - D r a f t 1

GL-6

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

A abbreviating commands

5-3

access point image

6-7

antenna connectors

C-2

Apply button

4-4

B

Back button 4-4 basic settings, checking

6-4

C

Cancel button 4-4

Cisco TAC

6-1

CLI abbreviating commands

5-3

command modes

5-2

editing features enabling and disabling

5-6 keystroke editing 5-6

wrapped lines

5-7

error messages

5-4

filtering command output

5-8

getting help

5-3

history

changing the buffer size 5-4

described

5-4

disabling

5-5

recalling commands

5-5

no and default forms of commands

5-3

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

I N D E X terminal emulator settings

3-4

command-line interface

See CLI

command modes

5-2

commands

abbreviating 5-3

no and default

5-3

connectors

C-1, C-2

console port

E-2

D data rates

C-2

declarations of conformity

B-1

default, configuration, resetting

6-5

default commands 5-3

E editing features enabling and disabling

5-6

keystrokes used

5-6

wrapped lines 5-7

EIRP, maximum

D-2 to ??, D-3 to ??

error messages, during command entry

5-4

extended temperature range

2-3, 2-4

F

FCC Declaration of Conformity

B-2

FCC Safety Compliance

2-2

filtering show and more command output

5-8

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

IN-1

Index

I

frequencies D-2, D-3

frequency range C-2

G global configuration mode

5-2

C I S C O C O N F I D E N T I A L - D r a f t 1

N

no commands 5-3

O

OK button 4-4 operating temperature

C-1

H help, for the command line

5-3

history changing the buffer size

5-4

described

5-4

disabling

5-5

recalling commands

5-5

Home button

4-4

P package contents

2-3

password reset

6-5

pinouts, serial cable

E-2

power connecting

2-14

injector

2-14

input

C-1

output

C-2

power level, maximum

D-2

privileged EXEC mode

5-2

indicators

6-2

input power C-1

installation guidelines

2-3

interface configuration mode

5-2

IP address, finding and setting

3-10

IPSU

3-9

K

key features 1-2

R range, radio

C-2

regulatory domains

D-2, D-3

regulatory information

B-1

reloading access point image 6-7

RF exposure

B-5

M

MAC

3-10, 3-11

management options, CLI

5-1

Mode button 6-7

modulation

C-2

S safety warnings, translated

A-1

serial cable

E-2

Cisco cable

E-2

size

C-1

IN-2

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

C I S C O C O N F I D E N T I A L - D r a f t 1

SSH Communications Security, Ltd.

5-9

status indicators

C-1

storage temperature

C-1

T

TAC 6-1

Telnet

3-12

temperature

operating C-1 storage C-1

terminal emulator

3-4

TFTP server

6-7

troubleshooting

6-1

U unpacking

2-3

user EXEC mode

5-2

V voltage range

C-1

W warnings

2-2, A-1

Web-based interface common buttons

4-4

compatible browsers

4-1

web site, Cisco Software Center

3-9, 6-9

weight

C-1

WEP key

6-4

OL-6226-01

Index

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

IN-3

Index

C I S C O C O N F I D E N T I A L - D r a f t 1

IN-4

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide

OL-6226-01

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents