Digital Cynos QEWDCM-26WT 26"LCD TV User Manual

Add to my manuals
43 Pages

advertisement

Digital Cynos QEWDCM-26WT 26

26” WIDE TFT-LCD TV

User ’ s Manual

FCC Information

This equipment has been tested and found to comply with limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment can generates, uses, and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inteference to radio Communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause unacceptable interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced Radio/ TV technician for help.

Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Safety Instructions

Notes & Descriptions

To reduce the risk of fire, electrical shock and other injuries, keep these safety precautions in mind when installing, using and maintaining your TV.

Warning : If you manipulate against the notice, it may cause serious injury or death to user.

Caution : If you manipulate against the notice, it may cause slight injury to user or appliance.

Ver 1.00NE

EN 2 26” WIDE TFT-LCD TV 3

Warning

Disconnect the power cable and signal cable connected to the product in case of thunder or lightning.

Do not attempt to touch its power cord with wet hands.

If any electric pin is wet or dusty, remove the moisture or dust first before use.

It is recommended to pull out the power cord unless you use it for a long time.

Damaged power cord, plug or unfitted outlet may be very dangerous.

Do not install the set close to any heating sources.

Do not place heavy articles on it or step on the product.

The product should be installed on a clean and dry place.

When you detect any smog, unusual noise or smell, just disconnect the electric power and refer servicing to qualified service personnel.

Do not place any bowl with water, beverage, can or other liquid products on it.

Do not use or place any combustible sprayer or inflammable substances close to the product.

Do not arrange the power cord close to any heating devices/sources.

Install the outdoor antenna for the set far away from high voltage cables.

EN 4 26” WIDE TFT-LCD TV

When moving it, do not apply any forces on the set.

Do not attempt to disassemble, repair or change the product.

Whenever you need to repair, adjust or check it, refer servicing to qualified service personnel.

Do not directly spray water or rub it with inflammable substances (thinner or benzene) when cleaning it.

Do not wet or penetrate water over/into the set.

When cleaning the LCD surface, disconnect the power and use a piece of smooth cloth against any scratches on it. Never use wet cloth.

Caution

Make sure to pull out the power cord when cleaning or removing the product.

Ventilation should be always open and the set should be installed in a wellventilated and wide enough place (a minimum distance away from a wall 10cm or more).

Do not install the set in a place directly exposed to sunlight.

5

Available Temperature & Humidity

Operating Temperature

Storage Temperature

Operating Humidity

Storage Humidity

0~35˚C

-10~50˚C

10~90% RH

10~90% RH

For dot defect [dead pixel] of LCD ;

TFT-LCD produced by using high-end semiconductor technology with precision of 99.9% above is used for this TV (2,949,120 pixels).

However the pixels of R.G.B. & White color seem to be right sometimes or some of black pixels could be seen on the LCD. This is not from bad quality or functional problem and you can use it without any problem.

Precautions when used as a PC monitor ;

Since the LCD TV is not designed for a PC monitor, it may not support very high resolutions that are supported in a PC. When you use it for the purpose, refer to the supportable resolution levels as follows.

When used as a PC monitor ;

Optimal Resolution: 1024 768 @ 60Hz

Max. Resolution: 1024 768 @ 85Hz.

Precautions for Image Ghost

Watching TV in a still image for an excessive time may seriously harm the LCD panel. Note that any troubles from the reckless use are not guaranteed and please be cautious of the use.

1. Digital broadcast is delivered in wide screen standard (16:9) DTV, so if the existing broadcasting program made in general screen size (4:3) is on the TV, both sides may not be completely displayed.

Any different brightness, in case limits to left/right sides are fixed, may leave image ghost of the limits on the LCD penal, if you watch it for a long time.

2. When you watch panorama broadcasting in a general display, it may show the central image with up/down parts removed.

Any different brightness, in case limits to top/bottom sides are fixed, may leave image ghost of the limits on the LCD penal, if you watch it for a long time.

3. Watching the screen in a still image for a long time may leave image ghost on the LCD panel.

EN 6 26” WIDE TFT-LCD TV 7

Contents

CHAPTER 1.

Before Use

1-1. Accessories

1-2. Panels

1-3. Remote Control

1-4. MENU Configuration

1-5. Jog Shuttle Button

1-6. Inserting the Batteries in the Remote Control

12

13

16

18

20

21

CHAPTER 2.

Connection

2-1. Connecting Power

2-2. Connecting TV Antenna

2-3. Connecting PC

2-4. Connecting PC DVI

2-5. Connecting DTV

2-6. Connecting DVD

2-7. Connecting VIDEO / S-VHS Input

2-8. Connecting Headphone (speaker) Output

2-9. Connecting VIDEO Output

26

27

28

29

30

24

24

25

25

EN 8 26” WIDE TFT-LCD TV

CHAPTER 3.

Using TV Menus

3-1. Watching TV

3-2. Auto On/Off Timer

3-3. Change TV Channel Mode

3-4. Channel Search & Fine Tune

3-5. Add/Remove Channel

3-6. Channel Swap

3-7. Password

3-8. Channel Lock

3-9. Caption

3-10. V-chip Funetion

3-11. DTV Field

3-12. Stereo

3-13. Bilingual (Multi-Language Broadcasting)

CHAPTER 4.

Using Menus of Picture,

Sound and Others

4-1. Setting Display Mode

4-2. Setting Scale Mode

4-3. Setting Picture Mode

4-4. Setting Simultaneous Picture Mode

4-5. Setting Screen MENU by Simultaneous Picture 61

4-6. Setting Sound 64

4-7. Setting Others 66

52

54

55

58

40

41

42

43

32

35

37

38

45

46

48

49

49

9

Contents

CHAPTER 5.

Using PC MENU

5-1. Auto Adjustment

5-2. Setting PC Scale Mode

5-3. Setting Phase/Frequency

5-4. Setting Position/Size

CHAPTER 6.

Specifications

6-1. Dimensions

6-2. Specifications

CHAPTER 7.

Services & Others

7-1. Troubleshooting

7-2. Concerning Services

78

79

82

84

70

72

73

74

EN 10 26” WIDE TFT-LCD TV

CHAPTER 1

Before use

1-1. Accessories

1-2. Panels

1-3. Remote Control

1-4. MENU Configuration

1-5. Jog Shuttle Button

1-6. Inserting the Batteries in the Remote Control

11

1-1. Accessories

Please make sure the following items are included with your LCD TV.

If any items are missing, contact your dealer.

Remote Control

EN 12 26” WIDE TFT-LCD TV

AAA-type battery( 2)

User’s Manual

DC 15V Adaptor

RF Cable D-Sub Cable

1-2. Panels

Front Panels

-4

-2

-1

-5

-3

Power/MENU

Channel Button

Sound Cont. / MENU SET

Remote Control Sensor

LED

-1. Power-On/Off

-2. AUTO / Move above MENU

-3. SOURCE / Move under MENU

-4. Exit MENU

-5. Load MENU

AUTO button searches automatically TV channels if set as TV, and it adjusts automatically for PC mode.

Power button is jog shuttle type button and it operates different functions by pushing it to Up/Down/Left/Right.

13

Rear Panels

Power Input

PC Input

DTV Input (Y Pb Pr LR)

TV Antenna Input

DVI Input

PC Sound Input

DVI Input (Y Pb Pr LR)

EN 14 26” WIDE TFT-LCD TV

Side Panels

Video/Audio Input

S-VHS Input

Headphone Output

Video/Audio Output

Upgrade (Only for service personnel)

15

1-3. Remote Control

TV & Input Source Selection Button

Channel Selection Button

Display Selection Button

Display Mode & Audio Control Button

MENU Control Button

Channel & Volume Control Button

TV Functions & Teletext Menu Button

PIP Function and Setting Button

EN 16 26” WIDE TFT-LCD TV

Functions by remote control buttons

Button

POWER

VIDEO

DVD

TV

DVI

DTV (TV2)

NORMAL

SPLIT

Function

Power On/Off

Composite Video Input

DVD Input (Y PbPr)

Button

MUTE

S-VHS

Function

Sound off Temporarily

S-Video Input

TV Input

DVI Input (Optional)

RGB

COMP

PC Input

DTV Component Input

PIP TV Input (Optional) / DTV Input (If DTV Tuner is built in)

Select Normal Display PIP PIP display

Split (PBP) TV SCAN 16 Channels Multi Scan

0~9

PRE

LIGHT

SOUND

FREEZE

Numeric Buttons

Previous Channel

Control background Light

Control Sound

Pause

ENT

PICTURE

SCALE

ON SCREEN

MENU Enter Main/Sub MENU EXIT

CH UP / DOWN Move TV channels / Move MENU up and down

VOL + / -

CAPTION

Control Volume / MENU settings

Turn On/Off Caption

MEM

SWAP

Zoom ON

Add/Remove a TV CH

Switch TV channels

Zooming On/Off

TUNE

CATV

IN

Input selected channels

Control Picture Mode

Control Picture Scale

Display screen status

Exit Main/Sub MENU

Finely adjust TV Channel

TV Mode

Zoom in

OUT Zoom out

AUTO TV : Channel search / PC : Auto Adjustment

SURROUND Surround effect STEREO

BILINGUAL

EPG

Select Multilanguage broadcasting system

Electronic Program Guide

(Option for DTV)

SLEEP

STEREO/MONO

Sleep TImer setting

WAKE UP Wake-Up Timer setting

PIP SOURCE PIP input signal change

PIP AUDIO

PIP SIZE

Switch Main/PIP sound

Control PIP size

PIP CH UP / DOWN Change PIP TV Channel

SET UP

PIP VIDEO

Other setting

Switch Main/PIP screen

PIP POSITION Change PIP position

The remote control provided is available up to 7m from the optical receive part within Left/Right

15 degrees.

17

1-4. MENU Configuration

Most functions of the TV set can be controlled by MENU and selection buttons on the remote control, so learning how to operate them would be convenient for you.

1. Menu Configuration

Main Menu Sub Menu

2. Press it again to move to sub menu of a selected main menu.

1) Press MENU button to display main menu.

2) Press it again to move to sub menu of a selected main menu.

3) Press EXIT to return from sub menu to main menu or from main menu to menu removal.

4) To move among menus, use CH button.

5) To change a selected menu setting, use VOL button.

Settings

EN 18 26” WIDE TFT-LCD TV 19

1-5. Jog Shuttle Button

1) Push MENU button right to display main menu.

2) Push it right again to display sub menu.

3) Push MENU button left to return to main menu.

4) Push it left again to clear menu.

5) Push the button up and down to move among menus.

If pushing it upward when menu is not displayed, it controls TV channel search or automatic PC settings.

If pushing it downward when menu is not display, it changes input signals.

6) Change menu settings by using left/right directional buttons.

1-6. Inserting the Batteries in the

Remote Control

1) Remove the cover of the remote control.

2) Check the polarity of batteries and insert them in right directions.

3) Replace the cover.

4) Available batteries : 2 DC 1.5V AAA-type batteries

Since incorrect insertion of batteries may cause breakage, leakage or injuries, check the polarities before the insertion.

Separate and collect used batteries for the protection of environment.

Do not use alkaline and manganese batteries together.

EN 20 26” WIDE TFT-LCD TV 21

EN 22 26” WIDE TFT-LCD TV

CHAPTER 2

Connection

2-1. Connecting Power

2-2. Connecting TV Antenna

2-3. Connecting PC

2-4. Connecting PC DVI

2-5. Connecting DTV

2-6. Connecting DVD

2-7. Connecting VIDEO / S-VHS Input

2-8. Connecting Headphone (speaker) Output

2-9. Connecting VIDEO Output

23

2-1. Connecting Power

1. The product automatically adjusts voltage.

In case 110V is used, connect 110V Conversion adaptor before use.

2. Power Cable should be firmly connected to an outlet or DC adaptor in order not to be pulled out or shake.

2-2. Connecting TV Antenna

1. When round cable (75

Ω coaxial cable) is used, copper part of the cable should not be bent.

Connecting RF cable

TV antenna

Connecting feeder cable

Antenna converter

TV Wall-outlet

RF cable feeder cable copper wire

TV Wall-outlet

Cautions

1. When an outdoor antenna is used, it is recommended for a skilled technician to install it.

2. It may be helpful to better display to purchase additional installing amplifier if there is any problem with weak radio wave.

EN 24 26” WIDE TFT-LCD TV

2-3. Connecting PC

1. Connect D-Sub Cable to D-Sub port on the TV and PC.

2. Connect Audio Cable (not included) to Audio output of a PC (stereo jack) and PC

Audio Input Port of the TV (stereo jack).

2-4. Connecting PC DVI

1. Connect DVI Cable (not included) to DVI port of the TV and PC.

2. Connect Audio Cable (not included) to Audio port of PC (stereo jack) and TV (stereo jack).

3. It is recommended to use D-type DVI cable.

25

2-5. Connecting DTV

Y P

B

P

R

L R

Digital TV Broadcasting Receiver

Y P

B

P

R

L AUDIO R

2-6. Connecting DVD (Y Pb Pr)

Y P

B

P

R

L R

DVD Playe

Y P

B

P

R

L AUDIO R

1. Connect Component Cable (not included) to DTV Connection ports of TV (Y Pb Pr) and DTV Receiver.

2. Connect Audio Cable (not included) to Audio ports (L/R) of TV and DTV Receiver.

3. Cables should be connected to ports of same colors.

4. Set the video output of a DTV Receiver as 480p, 720p.

1. Connect Component Cable (not included) to Component ports of TV and DVD player. VCR, Set-Top box or camcorder.

2. It supports 480i.

EN 26 26” WIDE TFT-LCD TV 27

2-7. Connecting VIDEO / S-VHS Input

VCR/DVD Player and etc

L R

Audio Output/Video Output/S-VHS Output

1. Connect Video/Audio Cable (not included) and S-VHS Cable to Video port of TV and camcorder, game machines, VCR, DVD player or Set-Top box.

2. Cables should be connected to ports of same colors.

3. Audio signals of S-VHS should be used with external audio signal cables.

4. S-VHS signal secures better quality than composite video signal.

2-8. Connecting Headphone (speaker)

Output

1. Connect Headphone (not included) to the Headphone output port of the TV.

2. Even in case of using headphone, internal speakers built in the TV still works and if you press MUTE button, the speakers stop working.

3. If possible, use the headphones of which impedance is 8 Ω . Other headphones may output too weakly or strongly.

4. In case of connecting to speakers, connect speakers with amps. If connected with speakers without amps, it may sound weakly.

5. In case of headphone output, volume is not controlled.

EN 28 26” WIDE TFT-LCD TV 29

2-9. Connecting VIDEO Output

1. When recording TV program or using the video/audio of the TV for other AV device

(VCR and etc), connect it to AUX Output terminal of the TV and Input Port of the device.

2. Cables should be connected to terminals of same colors.

3. External Output Signal outputs TV broadcasting signals of the main display.

EN 30 26” WIDE TFT-LCD TV

CHAPTER 3

Using TV Menus

3-1. Watching TV

3-2. Auto On/Off Timer

3-3. Change TV Channel Mode

3-4. Channel Search & Fine Tune

3-5. Add/Remove Channel

3-6. Channel Swap

3-7. Password

3-8. Channel Lock

3-9. Caption

3-10. V-chip Funetion

3-11. DTV Field

3-12. Stereo

3-13. Bilingual (Multi-Language Broadcasting)

31

3-1. Watching TV

1. Precautions in the initial installation

1) Check whether TV antenna cable is properly connected.

2) After checking whether the voltage is 100V or 220V, supply the electric power and connect the adaptor to the TV.

At the moment, TV is in standby.

2. Turning on TV

1) Turn on the Power button directly on the set or by remote control.

2) Each pressing the button turns on or off the set.

Power Button on Remote Control Power Button on the TV Set

3. Channel Selection

1) Press CH button on the remote control to change channels.

2) Press numeric buttons to go to a channel directly.

3) Press CH buttons ( ) on the TV set to increase or decrease TV channels.

Channel button on the remote control Channel button on the TV set

4. Volume Control

1) Increase/decrease volume by pressing VOL button on the remote control.

2) Press VOL button (< / > ) on the TV set to control the volume.

Volume Button on the remote control Volume Button on the TV Set

EN 32 26” WIDE TFT-LCD TV 33

5. Mute

MUTE button on the remote control

1) Press MUTE button on the remote control to sound off temporarily and “MUTE” is displayed.

2) Press it again to turn the sound back on or press volume buttons.

6. Move to Previous Channel

1) Every time pressing the PRE button on the remote control, it moves to a previous channel.

Previous Channel Button

7. Checking the present broadcasting information

Broadcasting Info Button

1) Press ON SCREEN button on the remote control to display the information on the screen.

2) Press ON SCREEN button again removes the information or leaving it clears the information in 5 seconds.

In case of TV Signal, it displays channel info while it shows mode info in case of PC signal.

3-2. Auto On/Off Timer

You may set the TV to turn on or off in a certain time period.

1. Setting Wake-Up Timer

- Press MENU button on the remote control.

- Set the time to turn on the TV automatically by using volume button on the remote control.

- Wake-up timer can be set from Off to 12 hours.

- Once the setting is complete, press EXIT button.

EN 34 26” WIDE TFT-LCD TV 35

2. Setting Sleep Timer

- Press MENU button on the remote control.

- Set the sleep timer by using volume button on the remote control.

- Sleep Timer can be set from Off to 180 minutes.

- Once the setting is complete, press EXIT button.

EN 36 26” WIDE TFT-LCD TV

3-3. Change TV Channel Mode

Please set your broadcast type between Air and Cable.

If its mode is set as Air, some Cable broadcasts are not able to watch.

CH Mode

Air Cable

- Press CATV button on the remote control.

SCREEN

PICTURE

TV

PC

SOUND

OPTION

Auto Scan

CH Fine Tune

CH Memory

CH Swap

CH Mode

CH Mode

Air Cable

- Set the CH Mode between Air & Cable by using Volume button on the remote control.

- Once the setting is complete, press CATV button or EXIT button.

- Also, it can be set in OSD menu if JOG button is used.

37

3-4. Channel Search & Fine Tune

When using the TV first after purchase, reconnecting it due to power failure or other reasons, channels should be searched and registered again.

Since Channel Search function searches channels currently broadcasted, you should execute it when most channels are broadcasted.

1. Channel Search

- Press MENU button on the remote control.

- Once you move to START by using Volume button on the remote control, it starts channel search.

- To stop channel search, repress EXIT button on the remoter control.

- If you stop it during channel search, it stores the currently searched channels only.

- Also, it can be set in OSD menu if JOG button is used.

2. Fine Tuning Channel Reception

If a searched channel is unclear or sounds abnormally, use Fine Tune function.

- Press MENU button on the remote control to move to Fine Tune Menu.

- If controlling menu settings left or right by using Volume button on the remote control, it searches the optimal status.

- Once the setting is complete, press TUNE button again or

- Also, it can be set in OSD menu if JOG button is used.

EXIT button.

EN 38 26” WIDE TFT-LCD TV 39

3-5. Add/Remove Channel

You may add or remove a channel as your need.

- Move to a channel to add or remove by pressing numeric buttons or CH button.

- Press MENU button on the remote control.

- In case of adding a channel by using Volume button on the remote control, move to

Add or Remove.

- Once the setting is complete, press EXIT button again or EXIT button.

3-6. Channel Swap

In case of channels frequently watch, you can switch it to other channel numbers and store them.

- Move to a channel to change.

- Press MENU button on the remote control.

- Change a channel number to switch by using Volume button on the remote control.

- Once the setting is complete, press EXIT button.

EN 40 26” WIDE TFT-LCD TV 41

3-7. Password

When using Contents Blocking function, you can set password and please keep the password private.

Default password is <0000>.

Please change default password to new one after installing TV.

- Press SET UP button on the remote control.

- Move to password menu by using MENU remote control and CH button on the

- Press MENU button on the remote control for entering Password setting menu.

- When setting password first after purchase, press <0000> on the remote control and press ENT changing.

or MENU on the remote control after entering new password for

- Press new password and ENT or MENU again for confirmation it.

EN 42 26” WIDE TFT-LCD TV

3-8.Channel Lock

You can make some channels to prohibit to watch by Channel Lock function.

It can be set only by remote control.

- Press SET UP button on the remote control.

- Move to CH Lock menu by using MENU button on the remote control.

- Enter your password by using the remote control.

- Set TV broadcast mode by using VOL button on the remote control.

43

- Move to the channel which you want to prohibit by using MENU

VOL button.

- Press ENT

- If you press or

ENT

MENU or button for setting it.

MENU again, it will be cancelled.

- It displays different color for CH Lock channel.

and

- Press EXIT for coming out from setting.

EN 44 26” WIDE TFT-LCD TV

3-9.Caption

This function works only Caption broadcast or other CC marked video tape and DVD title.

Set the function in the SETUP menu.

Caption can be set only by using the remote control.

1. Caption On / Off

- Press CAPTION button on the remote control when it is broadcasted.

- Press CAPTION button for coming out from setting.

2. Set Caption

- Press SETUP button.

- Move to Closed Caption menu by using CH button.

- Set Caption broadcast type by using VOL button on the remote control.

- Press EXIT button for coming out from setting.

45

3-10. V-Chip Funetion

It makes MPAA rating of TV broadcast and other media.

It works only with V-Chip function broadcast and media.

It can be controlled by using the remote control only.

- Press SETUP button on the remote control.

- Move to V-Chip menu by using CH button on the remote control.

- Press MENU

- Press ENT button and enter Password.

or MENU button on the remote control.

- Set V-Chip function by using VOL button on the remote control.

EN 46 26” WIDE TFT-LCD TV

- Move to TV Guideline or MPAA Rating by using CH button on the remote control.

- Move to the position which you want to make channel blocking and press ENT or MENU button for setting.

- Press it again for cancellation.

- Press EXIT button for coming out from setting.

47

3-11. DTV Field

Depending on a DTV receiver, a signal is not identical with standard signal. It may cause unclear display and if you change DTV Field value, it will be recovered to the normal picture (it can be set only by the remote control).

- Press SET UP button.

- Press MENU button to go into DTV Field Setting Menus.

- Set Not Invert/Invert with Volume button.

- Initially, ‘Not Invert’ is defaulted and you may change it to ‘Invert’ if the display is not normal.

- Once the setting is complete, press the EXIT button.

3-12. Stereo

If you use the TV in an area with weak or bad reception, there may cause sound noise or other problem when selecting a channel. In this case, cancel the STEREO setting.

It can be canceled only by the remote control.

- Press STEREO button on the remote control to cancel stereo and returning to Mono.

- Press STEREO button in Mono returns to Stereo.

- If Stereo is off, it is always set as Mono even though a channel is changed.

3-13. Bilingual

(Multi-Language Broadcasting)

In case of multi-language broadcasting, it can be converted if you wish to listen to other language except main language.

Multilanguage broadcasting can be set only by the remote control.

- Every time pressing BILINGUAL button on the remote control, the language display is changed in good order of main language sub language main + sub languages (dual language).

(Main - Sub - Dual)

EN 48 26” WIDE TFT-LCD TV 49

EN 50 26” WIDE TFT-LCD TV

CHAPTER 4

Using Menus of

Picture, Sound and

Others

4-1. Setting Display Mode

4-2. Setting Scale Mode

4-3. Setting Picture Mode

4-4. Using Simultaneous Picture Mode

4-5. Setting Screen MENU by Simultaneous Picture

4-6. Setting Sound

4-7. Setting Others

51

4-1. Setting Display Mode

You may view other video screen while watching TV.

- Press NORMAL , PIP , SPLIT or TV SCAN button.

1) NORMAL : Show a selected main screen in full size.

2) PIP : Show main screen and sub screen in full size and small size together.

3) SPLIT : Show main screen and sub screen by horizontally shared. You can control Main screen’s (left side screen) size and Sub screen’s size is controlled inverse ratio of main screen.

4) SPLIT FULL : Repressing SPLIT sub screen in split full screen.

button in Split display, shows main screen and

5) TV SCAN : Show 16 channels searched and stored in the TV set in 16 pictures in order on the screen. At the moment, TV SCAN can be operated only by the remote control.

- Also, it can be set in OSD menu if JOG button is used.

- OSD Menu is different depending on Display Type [Screen Layout].

EN 52 26” WIDE TFT-LCD TV 53

4-2. Setting Scale Mode

You can set the screen’s suitable image scale of TV or Video input signals and view them accordingly.

- Press SCALE button on the remote control.

- Control the scale in desirable size by using VOL

1) FULL : Show a screen in the full LCD Penal.

2) 16:9 : Show a screen in 16:9 wide screen size.

button on the remote control.

3) 4:3 : Show a screen in 4:3 screen size for general broadcasting.

4) CAPTION : Show a screen suitable for Caption Broadcasting.

5) SMART VIEW : Show a screen in a proportion suitable for grand image.

In PIP or SPLIT screen, it can be set in types of AUTO, 16:9, 4:3. For more information, see to 4-4 Setting Simultaneous Picture Mode.

- Once the setting is complete, press PICTURE button or EXIT button on the remote control.

- Also, it can be set in OSD menu if JOG button is used.

- OSD Menu is different depending on Display Type [Screen Layout].

4-3. Setting Picture Mode

By setting a picture mode suitable for broadcasting/video signals, you may enjoy better quality picture.

- Press PICTURE button on the remote control.

- Set a picture mode by using Volume button on the remote control.

1) Standard : Standard picture mode.

2) Soft : It displays a picture softly as a whole and is better for watching a film or TV series.

3) Dynamic : The mode is suitable for watching sports, which changes pictures fast.

4) User : It is a picture mode customized by a user.

- Also, it can be set in OSD menu if JOG button is used.

EN 54 26” WIDE TFT-LCD TV 55

1. Setting USER Mode

You can set each picture mode according to your taste. If you set USER mode as your taste, it is stored as USER Mode standard.

- Press MENU button on the remote control and move to PICTURE of main menu by using CH button on the remote control.

- Press MENU button on the remote control and move to the sub menu for changing values by using CH / VOL buttons.

1) Brightness : Adjust screen brightness.

2) Contrast : Adjust screen contrast.

3) Color : Adjust screen color.

4) Sharpness : Adjust screen sharpness.

5) Room Light : Adjust the brightness of TV screen according to background brightness.

2. Setting Room Light

You can adjust the entire TV brightness according to lightning status.

- Press MENU button on the remote control.

- Adjust values by using Volume button on the remote control.

- Once the setting is complete, press EXIT button on the remote control.

EN 56 26” WIDE TFT-LCD TV 57

4-4. Setting Simultaneous Picture Mode

While watching TV on main screen, you can enjoy other video picture on the sub screen.

Simultaneous Picture means PIP and/or SPLIT Picture display.

1. Changing a channel of Simultaneous Picture

- Press PIP CH button on the remote control.

- It changes a TV channel if the sub screen shows TV.

2. Changing input signal of Sub-Screen

- Press PIP SOURCE button on the remote control.

- Every time pressing PIP SOURCE button, it changes input signal of sub screen.

- Available input signals of sub screen are as follows;

SUB

MAINRGB

PC RGB

PC DVI

TV1

TV2

VIDEO

S-VHS

COMP (DTV)

DVD

0

0

0

X

PC

RGB

X

X

X

0

0

0

0

X

PC

DVI

X

X

X

0

TV1

0

X

X

X

X

0

0

0

TV2

X

0

0

0

0

X

X

X

VIDEO S-VHS

0

X

X

X

X

0

0

0

0

0

X

0

X

X

0

X

0

0

0

X

COMP

(DTV)

X

X

X

O

DVD

0

X

X

X

X

0

0

0

EN 58 26” WIDE TFT-LCD TV

3. Changing Sub Screen Size

It adjusts sub screen size.

- Press PIP SIZE button on the remote control.

- Adjust sub screen size by Volume button on the remote control.

- Different menus are displayed depending on PIP Picture or SPLIT

Picture.

- On PIP Picture, sub screen size can be adjusted from 1/16 to 1/4 of the full size.

- On SPLIT Picture, main screen size is adjusted while sub screen size is adjusted accordingly.

- On SPLIT Picture, the left screen always shows main screen.

59

4. Changing Sub Screen Position

Adjust a sub screen’s position on PIP Picture.

- Press PIP POSITION button on the remote control.

- Move PIP picture to a desirable position by using CH / VOL on the remote control.

button

- The position is set as USER setting of OSD menu.

- Once the setting is complete, press PIP POSITION or EXIT the remote control.

button on

5. Switching Main/Sub Screen

It switches main/sub screens.

In case of switching main/sub screens, audio is changed accordingly.

The left screen always shows main screen.

6. Switching Audio of Main/Sub Screen

It switches audio of main/sub screen.

In case of switching audio of main/sub screen, it switches audio only, not screens.

4-5. Setting Screen MENU by

Simultaneous Picture

Depending on Layout in OSD Menu, sub menus of SCREEN are changed.

1. SCREEN MENU in NORMAL Picture

- It works only in NORMAL Picture.

- Select SCREEN menu by pressing MENU

MENU).

button on the remote control (MENU

1) Layout : Set Picture mode [Display Mode].

2) Image Scale : Select an image scale

(FULL, 16:9, 4:3, Caption, Smart View)

- Once the setting is complete, press EXIT button to exit it.

EN 60 26” WIDE TFT-LCD TV 61

2. Screen Menu on PIP Picture

- It works only on PIP Picture.

- Select SCREEN menu by pressing MENU button on the remote control.

3. SCREEN Menu in SPLIT Picture

- It works only on SPLIT Picture.

- Select SCREEN menu by pressing MENU button on the remote control.

1) Layout : Set a display layout.

2) Image Scale : Select an image scale of main screen.

(FULL, 16:9, 4:3, Caption, Smart View)

3) PIP Position : Adjust the position of PIP

(L-Top, L-Bottom, R-Top, R-Bottom, USER)

4) PIP Position X / Y : In case of PIP Position menu is set as USER, it sets X/Y position of PIP.

5) PIP Size : Adjust PIP size. It can be adjusted from 1/16 to 1/4 of full screen.

6) PIP Scale : Adjust image scales of PIP.

- Auto : Adjust PIP scale by automatically determining input signals.

- 16:9 : It fixes PIP scale to 16:9.

- 4:3 : It fixes PIP scale to 4:3.

1) Layout : Set a display layout

2) Split Size : Adjust a size of Split main screen. Sub screen size is adjusted by main screen size.

3) SPLIT Scale : Adjust an image scale of SPLIT Picture.

- Auto : Adjust PIP scale by automatically determining input signals.

- 16:9 : It fixes PIP sub screen scale to 16:9.

- 4:3 : It fixes PIP sub screen scale to 4:3.

EN 62 26” WIDE TFT-LCD TV 63

4-6. Setting Sound

You can set sound suitable for TV broadcasting or Video.

1. Mode Setting

- Press SOUND button on the remote control to display SOUND mode setting.

- Set the menu settings by using Volume button on the remote control.

1) Standard : Standard sound mode.

2) Music : Music broadcasting mode.

3) Movie : Cinema broadcasting mode.

4) News : News broadcasting mode.

5) User : User’s customization mode.

Also, it can be set in OSD menu if JOG button is used.

2. USER Mode Setting

USER mode can be set only in OSD menu.

- Press MENU button to go into main menu.

- Move to SOUND menu by using CH button.

- Press MENU button to move to the Sub Menu.

- Adjust sound in a desirable frequency bandwidth by using VOL

/ CH button on the remote control.

3. SURROUND Setting

Surround mode can be set only by the remote control.

- Press SURROUND button on the remote control.

- Set ON/OFF by using Volume button on the remote control.

- Once the setting is complete, press SURROUND control.

or EXIT button on the remote

Balance : Control the balance of Left/Right speakers.

EN 64 26” WIDE TFT-LCD TV 65

4-7. Setting Others

Press MENU button on the remote control to move to Main Menu.

Move to OPTION menu by using CH button on the remote control

Press MENU button to move to the Main menu.

Change the settings by using VOL / CH button on the remote control.

1. Menu Timeout Setting

It can be adjusted to display OSD Menu between 5 ~ 60 seconds.

2. Setting OSD Menu Language

Change a language to display OSD.

3. Factory Reset

Reset all the OSD control settings back to the factory setting status.

EN 66 26” WIDE TFT-LCD TV 67

4. Version

It shows the product version.

CHAPTER 5

Using PC MENU

5-1. Auto Adjustment

5-2. Setting PC Scale Mode

5-3. Setting Phase / Frequency

5-4. Setting Position / Size

69 EN 68 26” WIDE TFT-LCD TV

5-1. Auto Adjustment

In case of using it as a PC monitor, it is automatically set.

When the set is connected to a PC, the MODE should be set as PC RGB Mode.

- Press MENU screen status.

button on the remote control to automatically set the product’s

- Move to START by using Volume button on the remote control to start Auto

Adjustment.

When it is used as a PC monitor;

Optimal Resolution: 1024 x 768 @ 60Hz

Max. Resolution: 1024 x 768 @ 85Hz.

- It may not normally display picture in any resolution out of the optimal resolution range.

- When you use it as a PC monitor, it requires to be set the Standard Signal Mode for

PC Monitor before use.

- Even though it is automatically adjusted, it may not normally display picture depending on signals from a PC and in this case, it is recommended to execute Auto

Adjustment for several times.

EN 70 26” WIDE TFT-LCD TV

The Standard Signal Modes for PC Monitor

Resolution

(H V)

640 480

640 480

640 480

720 400

800 600

800 600

800 600

1024 768

1024 768

1024 768 (Optimal)

Vertical Frequency Horizontal Frequency Clock Frequency

(kHz) (Hz) (MHz)

Polarity

(Vert./Hor.)

31.469

37.861

59.94

72.809

25.175

31.5

-/-

-/-

37.5

31.469

37.879

48.077

75

70.087

60.317

72.188

31.5

28.322

40

50

-/-

-/+

+/+

+/+

46.875

48.363

56.476

60.023

75

60.069

70.069

75.029

49.5

65

75

78.75

+/+

-/-

-/-

+/+

When you use it as a PC monitor, depending on signals of a PC, it may not display picture normally even though it is set for standard mode resolution.

71

5-2. Setting PC Scale Mode

When being used as a PC Monitor, the scale can be adjusted.

PC Monitor Scale works only when PC signal is connected and input signals are selected in RGB mode.

- Press SCALE button on the remote control.

- Select a desirable scale by using Volume button.

- Once the setting is complete, press EXIT button.

1. 1:1 : Display the resolution as 1:1.

2. Fill All : Display picture in the full screen regardless of the resolution.

3. Aspect Ratio : Display the resolution in 4:3 aspect ratio. Also, it can be set in OSD menu if JOG button is used.

5-3. Setting Phase / Frequency

In case it is not optimally set even though automatically adjusting it, use PHASE function.

- Press MENU button on the remote control.

- Move to PC menu by using CH button.

- Move to PHASE menu by pressing MENU

- Adjust settings by controlling Volume button.

button.

- Once the setting is complete, press EXIT button.

EN 72 26” WIDE TFT-LCD TV 73

5-4. Setting Position / Size

Adjust the position and size of the PC Monitor.

1. Setting Vertical/Horizontal Position

- Press MENU button on the remote control.

- Move to PC Menu by using CH button.

- Move to H / V Position Menu by using MENU button.

- Adjust settings by controlling VOL

- Once the setting is complete, press button.

EXIT button.

(1) Setting Vertical/Horizontal Size

- Press MENU button on the remote control.

- Move to PC Menu by using CH button.

- Move to H / V Size Menu by using MENU button.

- Adjust settings by controlling Volume button.

- Once the setting is complete, press EXIT button.

EN 74 26” WIDE TFT-LCD TV 75

EN 76 26” WIDE TFT-LCD TV

CHAPTER 6

Specifications

6-1. Dimensions

6-2. Specifications

77

6-1.Dimentions

86mm

660mm

520mm

228mm

<Wall-Mounting Hole Position>

223mm

423.3mm

M4 6mm, 4 points

393mm

480mm

Weight : approx. 19kg (before packing) / approx. 22kg (after packing)

EN 78 26” WIDE TFT-LCD TV

6-2. Specifications

Dimensions, apparent design and specifications are subject to change without any prior notice for the performance improvement.

Product Name

LCD Panel

26 ” WIDE TFT-LCD TV

Type Amorphos Silicon TFT-LCD

Size

Pixel Pitch

26” Wide (diagonal length)

0.4425 mm x 0.4425 mm

Contrast Ratio

Brightness

Actual Display Size

Viewing Angle

Interface

500 : 1 (Typ.)

500 cd /

372.48 mm (H) x 223.49 mm (V)

L/R: 88°/ 88° U/D: 88°/ 88°

TV Channel

LVDS

VHF: 2~13 channels UHF: 14~69 channels

TV Broadcasting System

Audio Output

PC Monitor

Power

Power Consumption

Cable: 1, 14~125 channels

PAL / SECAM , NTSC-M Type

Horizontal Frequency

Vertical Frequency

Colors

Max. Resolution

Other Resolutions

Adaptor Input

Adaptor Output

In-Operation

MAX 20W + 2 / Stereo

30 ~ 61 kHz

56~ 85 Hz

16.7M colors (8bit)

XGA : 1024 (H) x 768 (V)

XGA, SVGA, VGA

AC 100V~240V, 50~60Hz

DC 15 V

< 120W

Power-Saving Mode/OFF < 5W

Energy Saving Mode VESA DPMS

79

EN 80 26” WIDE TFT-LCD TV

CHAPTER 7

Service & Others

7-1. Troubleshooting

7-2. Concerning Services

81

7-1. Troubleshooting

Before contacting service to service personnel, please check the followings first.

If you still have the same symptoms even after taking the following actions, contact your local dealer or qualified service personnel.

1. TV-related Troubles

Unclear display or noisy sound

Check whether TV antenna is correctly connected.

Broadcasting may not be good in an area with bad reception or far away from a station/network.

No image

Check whether you connect the power cord properly. And press the POWER button.

Black background only

Check whether the mode is set as PC monitor or Video/S-VHS Input, not TV mode.

Strips and shaking display

It may be interrupted by neighboring radio waves (please check any wireless phone, hair drier, electric drilling machine and etc)

Execute fine tuning for manual adjustment.

Can’t catch a specific channel

Check whether Channel Setting is normally set.

Try to rotate an antenna’s direction.

Picture plays without sound

Try to press MUTE button.

Volume up by using Volume button.

EN 82 26” WIDE TFT-LCD TV

2. PC Monitor-related Troubles

No image on the monitor

Check whether the D-Sub cable is firmly connected to the TV and a PC.

Check whether a graphic card is correctly inserted into the slot.

Check whether the Power of a PC and the TV is on.

Check whether a graphic card or mode is set appropriately on a PC.

Referring to the Standard Signal Mode for PC Monitor in the previous chapter, change graphic mode.

Check whether D-Sub cable pins are not inserted or bent.

No Power

Check whether the power cord is normally inserted and reconnect it.

Pull out the power cord from wall outlet and reconnect it in 10~20 minutes.

LED Lamp turns off in red and it shows no image

Check whether the graphic cable is connected to theTV and a PC.

Check whether a computer is in power-saving mode and attempt to operate keyboard and mouse.

Unstable or unfocused image or trembling

Check whether the D-Sub cable is connected to the TV and a PC.

If a PC’s display mode is changed, the screen needs readjusting, so you need to use Auto Adjustment or Picture Adjustment.

Check whether the TV and your graphic card are compatible each other and whether it is set as an appropriate refresh rate. If letters look distorted, change the refresh rate to 60Hz.

Abnormal image scale

By using vertical/horizontal position in Picture Adjustment Menus, adjust the position.

Try to execute Auto Adjustment function.

83

7-2. Concerning Services

We guarantee free of charge After-sales service for a full year if any troubles are found when you are using our product. However, any natural disasters or careless use cause the trouble, it may cost even within a valid warranty period.

Responsibility of Chargeable After Sales Service (Customer’s Charge)

In one of the following cases, it may cost even in the valid warranty period.

1. In case of any troubles resulting from inserting of foreign substances (water, beverage, coffee and etc)

2. Dropping or applying force cause a trouble to damage on the product or induce malfunction.

3. Appearance damage or transformation by use of organic solutions such as thinner, benzene and etc.

4. When it gets troubled due to your disassemble.

5. When other parts/consumption accessories (including adaptor) that are not supplied by the company may directly cause any troubles.

6. Supplying wrong voltage may cause a trouble

7. Any personnel not from qualified service personnel repairs or modifies the product, resulting in troubles.

8. Natural disasters (lightning, fire, flood, gas, damage from sea wind, earthquake and etc) directly cause troubles

9. Violation against the directions in the manual cause any troubles

10. Customer’s mishandling cause a trouble

11. In case the date of purchase may be vague, the valid warranty period is counted after 2 months since the product is manufactured.

EN 84 26” WIDE TFT-LCD TV

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement