Furuno MODEL1722C series, MODEL1722 series plotter, MODEL1833 series, MODEL1833C series radar User manual
Below you will find brief information for plotter MODEL1722C series, plotter MODEL1722 series. This user manual covers the basics of using your plotter. You will learn how to navigate using waypoints, tracks, and marks, as well as how to change the display settings and use the various features of the plotter. You can also find information on how to connect the plotter to a radar and use the target tracking feature.
Advertisement
Advertisement
3. PLOTTER OPERATION
The compass display, displayed at the bottom half of the screen in the combination display, provides steering information. The compass rose shows two triangles: the black triangle (hollow on monochrome model) shows the bearing to destination waypoint and the red (solid on monochrome) triangle, which moves with ship’s course, shows own ship’s course.
The water temperature and depth graphs, which require appropriate sensors, show the latest 10 minutes of temperature and depth data. The range of the depth graph is 50 feet and it is automatically adjusted with depth.
Destination waypoint
Speed over ground
Range to destination waypoint
Speed through water
TTG
003WPT
0D 9H 59M
RNG 9 9 . 9 n m
SOG 10.0
kt STW 10.0 kt
ETA 23th23:59
Time-to-go to destination
Destination waypoint bearing
(black and filled on color model, hollow on monochrome model)
Depth graph*
DPT
4 5 . 2 f t
0
50
* = Requires appropriate sensor.
Shown (in red on color model) when direction to steer is "left." w
BRG
3 5 9 . 9
°
M
N
20
TMP
1 6 . 2
°
F
CSE
3 5 9 . 9
°
M
E
10
Estimated time of arrival at destination
Ship's course
(red and filled on color model, filled on monochrome model )
Water temperature graph*
Direction to steer
(green on color model)
Bearing scale
Own ship marker
(For color model, black when within XTE range, yellow when over; flashes when over XTE range on monochrome model)
XTE monitor (See next page for description.)
Compass display
3-3
3. PLOTTER OPERATION
Reading the XTE (cross-track error) monitor
The XTE monitor, located below the compass rose, shows the amount you are off course and the direction to steer to return to course. The own ship marker shows the direction and amount your ship is off course. It is shown in black when the amount of cross-track error is within the XTE monitor range and yellow when it is over. (On the monochrome model it flashes when the amount of cross-track error is more than the XTE monitor range.) An arrow appears at the right or left side of the XTE monitor and it shows the direction to steer to return to intended course. (For the color model the arrow is shown in red when you should steer left, and green when you should steer right.) In the example on the previous page you would steer right to return to course. To maintain course, steer the vessel so the own ship marker stays at the center of the XTE monitor.
Soft keys
EDIT XT-LMT : Sets the range for XTE monitor scale. See the procedure below for how to set.
RESTART NAVGATION TO
CURRENT WAYPOINT.
ARE YOU SURE?
YES ... PUSH ENTER KNOB
NO ... PUSH CLEAR KEY
(Setting the range for the XTE monitor)
1. With the compass (or highway) display shown, press the EDIT XT-LMT soft key to display the following window.
XTE LIMIT
0 . 1 n m
XTE range setting window
2. Use the cursor pad to select digit to change. Note that all digits may be cleared by pressing the [CLEAR] key.
3. Use the [ENTER] knob to set value, or press the CANCEL soft key to cancel.
RESET XTE: Displayed when destination is set, and enables you to restart navigation. When this soft key is pressed, the following message is displayed.
3-4
3. PLOTTER OPERATION
The highway display, displayed at the lower half of the screen in the combination display, provides a graphic presentation of ship’s track along intended course. It is useful for monitoring ship’s progress toward a waypoint. The own ship marker shows relation between ship and intended course. The XTE monitor shows the direction and amount your vessel is off course – the arrow shows the direction to steer to return to your course and the numeric the distance you are off course.
Using the figure below as an example, you would steer right 0.009 nm to return to course. To maintain course, steer the vessel so the own ship marker stays aligned with the intended course line.
Speed over ground, speed through water
Destination waypoint
Range to destination waypoint
Time-to-go to destination
Destination waypoint
TTG
RNG 9 9 . 9 n m
003WPT
SOG 10.0
kt
0D 9H 59M ETA
STW 10.0 kt
23th23:59
WPT001
Estimated time of arrival at destination
Intended course
Own ship marker
0.9 nm 0 . 0 0 9 n m 0.9 nm XTE range
Direction to steer (green on color model)
XTE monitor
Shown (in red on color model) when direction to steer is "left."
Highway display
Soft keys
EDIT XT-LMT : Sets the range for the XTE monitor scale. See the procedure on the previous page for how to set.
RESET XTE: Displayed when destination is set, and enables you to restart navigation. See the description on the previous page.
3-5
3. PLOTTER OPERATION
3.1.4 Nav data display
The nav data display provides comprehensive navigation data. The user may select what data to display and where to display it, on the NAV DATA DISPLAY
SETUP menu. For details see paragraph “5.8 Nav Data Display Setup.”
Appropriate sensors are required. Bars ( - -) appear when corresponding sensor is not connected.
Position
POSITION
34
°
34. 5678' N
120
°
34. 5678' W
WPT POSITION
34
°
14. 5678' N
120
°
14. 5678' W
STW
10.0 kt
BEARING
9.2
°
M
DEPTH
1324.1 ft
SOG
10.0 kt
COURSE
101.6
°
M
RANGE
0.18 nm
TEMP
18.2
°
C
Depth
Bearing to waypoint
Water temperature
Range to waypoint
Course Speed through water
Waypoint
Position
Speed over ground
Full-screen display
Nav data displays
TRIP LOG
103 nm
TTG
0 D 2 H 30 M
ETA
1st 1:25
DATE 2001
FEB 1
TIME
01:27:05
Half-screen display
3-6
3. PLOTTER OPERATION
Three types of presentation modes are provided for the plotter display: north-up, course-up and auto course-up. To change the presentation mode, first press the
[HIDE/SHOW] key if the plotter soft keys are not displayed. Press the MODE soft key to select desired mode. Each press of the key changes the presentation mode and presentation mode indication (top right-hand corner of the screen) cyclically in the sequence of North-up, Course-up and Auto course-up.
3.2.1 North-up
North is at the top of the display and own ship, shown by a filled circle. This mode is useful for long-range navigation.
34
°
22. 3456'N 359.9
°
TRIP
NU
080
°
22. 3456'E 19.9 kt 99.9 nm
16.0nm
MARK
ENTRY
MODE
NTH UP
NAV
POS
WP-002
FISH
BRIDGE
D.BOX
ON/ OFF
Plotter display, north-up mode
3-7
3. PLOTTER OPERATION
3.2.2 Course-up
The destination is at the top of the screen when a destination is set. When no destination is set, the course or heading is at the top of the screen at the moment the course-up mode is selected. A filled triangle marks own ship’s position.
Note: The data sentences GGA and VTG must be output from the NavNet display unit connected to the GPS navigator in order to correctly orient the own ship marker in the course-up mode on other NavNet display units.
+
16.0nm
34
°
22. 3456'N 359.9
°
M TRIP
CU
080
°
22. 3456'E 19.9 kt 99.9 nm
WPT 001
MARK
ENTRY
MODE
CSE UP
CENTER
GO TO
CURSOR
D. BOX
ON/ OFF
Plotter display, course-up mode, destination set
The course is at the top of screen at the moment the auto course-up mode is selected. n this mode, the current course is kept at the top of the screen within
22.5 degrees. For example, if your vessel turns for than 22.5 degrees to port or starboard, the chart display will rotate so that your course is pointing towards the top of the screen again.. A filled triangle marks own ship’s position.
+ 34
°
22. 3456'N 359.9
°
M TRIP
CU
080
°
22. 3456'E 19.9 kt 99.9 nm
16.0 nm MARK
ENTRY
MODE
AT CU
CENTER
GOTO
CURSOR
D. BOX
ON/ OFF
Plotter display, auto course-up mode
3-8
3. PLOTTER OPERATION
3.3 Shifting the Display
The plotter display can be shifted on the plotter display as below.
1. Press the cursor pad to display the cursor.
2. Locate the cursor at a screen edge and press and hold down the cursor pad.
The screen shifts in the direction opposite of cursor location.
3. To automatically return the cursor to the screen center, press the CENTER soft key. This also returns own ship marker to the screen center.
Chart scale (range) may be selected with the [RANGE -] or [RANGE +] key. The
[-] key expands the chart range; the [+] key shrinks it.
Charts scales nm 0.125 0.25 0.5 1 2 4 8 16 32 64 128 256 512 1024 km 0.23 0.46 0.93 1.85
3.70
7.41
14.8
29.6 59.3 119 237 474 948 1896 sm 0.144 0.29 0.58 1.15
2.30
4.60
9.21
18.4 36.8 73.7 147 295 589 1178
Note: When the display is expanded or shrunk beyond the range of the chart card in use the message “NO CHART” appears, along with the appropriate chart icon. See the illustration on the next page for details.
3-9
3. PLOTTER OPERATION
3.5.1 Chart card overview
Your system reads FURUNO and NavCharts ™ (NAVIONICS) charts, or C-MAP charts, depending on its specification.
When you insert a suitable chart card in the slot and your boat is near any chart graphic data, a chart appears. If a wrong card is inserted or a wrong chart scale is selected, land masses will appear hollow. Insert the proper card and select a suitable chart scale. Chart icons appear at the top of the display to help you select a suitable chart scale. The table below shows the chart icons and their meanings.
Chart icons and their meanings
Icon Meaning
Proper card is not inserted or chart scale is too small.
Operate the RANGE key to adjust chart scale.
Chart scale is too large.
Operate the RANGE key to adjust chart scale.
Suitable chart scale is selected.
3-10
3. PLOTTER OPERATION
3.5.2 Indices and chart enlargement
When the [RANGE] key is operated, you will see several frames appear on the chart. These frames are called indices and they show you what parts of the chart can be zoomed in on.
Sample chart (Japan) showing indices
When a chart cannot be displayed
A chart will not be displayed in the following conditions:
• When the chart scale is too large or too small.
• When scrolling the chart outside the indices.
• When this happens, select proper chart scale.
Note: Indices can be turned on or off with “Chart border line.” See page 5-13 for
FURUNO and NAVIONICS charts and 5-16 for C-MAP charts.
3-11
3. PLOTTER OPERATION
3.5.3 FURUNO and NavCharts ™
Chart symbols
The table below shows FURUNO and NavCharts ™ mini chart symbols and their meanings.
Chart symbols
Symbol Description
Summit
Wreck
Lighthouse
Lighted Buoy
Buoy
Radio Station
Symbol Description
Position of Sounding
Obstruction
Fishing Reef
Platform
Anchorage
Data for aids to navigation
Selected FURUNO and NavCharts ™ charts can show buoy and lighthouse data.
Simply place the cursor on the lighthouse or buoy mark.
Place the cursor on a lighthouse or buoy mark.
Lighthouse mark
Example of data displayed
Range and bearing from own ship
Period (ex.: 6 seconds)
Visibility in nautical mile (ex.: 12 miles)
NAVAID: /FL 6S 12M
FROM OS 52.38nm 48.0
°
FL : Flashing
F : Fixed light
F FL : Fixed and Flashing light
MO : Morse code light
Oc : Occulting light
Example of buoy, lighthouse data
3-12
3. PLOTTER OPERATION
Port service icons (NavCharts ™ only)
NavCharts ™ show services available at ports, with icons. Use the cursor pad to place the cursor on the sailboat icon (denotes a port or harbor), and then push the [ENTER] knob. The services available appear at the top of the display.
Detailed information of service selected
List of services at the port selected
+ 34
°
22. 3456'N 359.9
°
M TRIP NU
080
°
22. 3456'E 19.9 kt 99.9 nm
FIRST AID
16.0nm
Emergency medical service
Fueling station
Water supply station
Traveler's service station
CANCEL
Customer service station
Marine equipment service
Sailboat icon (Port) Port Information center
Plotter display, showing port service display
3-13
3. PLOTTER OPERATION
Cursor and data display
Besides its fundamental functions of providing position data, the cursor can also show caution area, depth area, source of data, etc. on C-map charts. In addition, you can display information about an icon by placing the cursor on it.
1. Press the cursor pad to turn the cursor on.
2. Use the cursor pad to place the cursor on the position desired.
3. Push the [ENTER] knob to open the Objects window.
Objects
Navigation mark, fixed
Beacon, generic
Light
Light
Depth area
Source of data
Objects window
4. Use the cursor pad to select the item desired.
5. Push the [ENTER] knob to display details for object selected.
Navigation Mark, fixed
Light
Color
White
Height
12.0 Meters
Light characteristic flashing
Sectorlimit one
64.0 Degrees
Sectorlimit two
138.0 Degrees
Signal group
(3)
Signal period
10.0 Seconds
Example of caution area window
6. Press the RETURN soft key to close the window.
7. Repeat step 4 to 6 to select other item.
8. Press the [MENU] key to close the menu.
3-14
3. PLOTTER OPERATION
Icon data
You may place the cursor on any icon to find information about the selected icon.
1. For example, place the cursor on a lighthouse icon.
Place the cursor on a lighthouse icon.
+ 34
°
22. 3456'N 359.9
°
M TRIP
NU
080
°
22. 3456'E 19.9 kt 99.9 nm
16.0nm
MARK
ENTRY
MODE
NTH UP
CENTER
GO TO
CURSOR
D. BOX
ON / OFF
Lighthouse icon
2. Push the [ENTER] knob to show data. For example, the following window appears for a lighthouse.
Objects
Lighthouse
Tower
Light
Underwater Lock
Depth contour
Depth contour
Depth area
Source of data
Object windows
3. Use the cursor pad to select the item desired.
4. Push the [ENTER] knob to display detailed information.
3-15
3. PLOTTER OPERATION
Navigation mark, fixed
Light.
Color
white
Height
7. 00 Meters
Light characteristic
occulting
XXXXXXXX
XXXXXXXX
Sample lighthouse data
5. Press the RETURN soft key to close the Objects window.
Tide information
The C-MAP chart card provides for calculation of the tide heights for any date.
Additionally it displays the times of sunrise and sunset.
1. Press the cursor pad to place the cursor on a Tide icon ( T ).
2. Push the [ENTER] knob to open the Objects window.
+ 34 24. 3456 N 359.9 NU
OBJECTS
Tide height
Cartographic area
Source of data
T RETURN
Objects window
3. Use the cursor pad to select “Tide height.”
4. Push the [ENTER] knob to open the TIDE window.
3-16
Horizontal
Cursor
Vertical
Cursor
3. PLOTTER OPERATION
0.86
TRIP
NU
t 99.9 nm
0.74
DATE
0.61
0.48
0.35
0 4 8 12 16 20 24
Time: 04:35
Height: 0.45ft
Draught: 0.65ft
01/07/30 +13:30
43
°
32.860N
010
°
18.022E
RETURN
Port info
LIVORNO (LEGHORN)
High Water(max)
0.86ft(13:30 L)
Low Water(min)
0.35ft(21:00 L)
Sunrise
07:52L
Sunset
16:53 L
Tide window
5. Press the DATE soft key to open the DATE window.
CHANGE DATE
(DAY. MONTH. YEAR)
0 1. 01. 2001
LIMIT: 31.12.2099
Date window
6. Use ◄ or ► to position the cursor where desired and then rotate the
[ENTER] knob to set. Repeat to enter complete date.
7. Push the [ENTER] knob to show the tidal graph for entered date.
8. Use ◄ or ► to locate the vertical cursor on the hour desired.
9. Use ▲ or ▼ to shift the level cursor to select draught.
10. See the time, height and draught indications below the tide graph for tide information.
11. Press the RETURN soft key to close the TIDE window.
3-17
3. PLOTTER OPERATION
Your ship’s track is plotted on the screen using navigation data fed from a navigation receiver. This section shows you what you can do with track, from turning it on or off to changing its plotting interval. Own ship’s track is displayed in the default setting and on the color model it is red.
Own ship track
1. Press the [MENU] key followed by the CHART SETUP and TRACKS &
MARKS CONTROL soft keys to open the TRACK CONTROL menu.
TRACK
CONTROL
TRACK
CONTROL
OWN SHIP TRACK DISP
ON
OWN SHIP TRACK COLOR
RED
TARGET TRACK DISPLAY
ON
TARGET TRACK COLOR
WHITE
INTERVAL
TIME
TIME INTERVAL
00m10s
DISTANCE INTERVAL
00.10nm
MEMORY(TRACK & MARK)
2000PTS
(MARK MEMORY)
(6000)POINTS
EDIT
TRACK
RESUME
ERASE
T & M
MARK
OWN SHIP TRACK DISP
ON
TARGET TRACK DISPLAY
ON
INTERVAL
TIME
TIME INTERVAL
00m10s
DISTANCE INTERVAL
00.10nm
MEMORY(TRACK & MARK)
2000PTS
(6000)POINTS
RETURN
EDIT
TRACK
RESUME
ERASE
T & M
MARK
SETUP
RETURN
SHIP’S TRACK STATUS
TRACKING
TRACK: 1234/2000
MARK : 9/6000
SHIP’S TRACK STATUS
TRACKING
TRACK: 1234/2000
MARK : 9/6000
MODEL1722C series MODEL1722 series
Track control menu
2. Use the cursor pad to select OWN SHIP TRACK DISP.
3. Press the EDIT soft key to show the track display window.
4. Use the cursor pad to select ON (default setting) or OFF as appropriate.
5. Press the ENTER soft key.
6. Press the [MENU] key to close the menu.
Note: The number of track and mark points used appears at the SHIP’S TRACK
STATUS window on the TRACK CONTROL menu. Using the figure above as an example, 1234 points of track and 9 marks have been recorded.
3-18
3. PLOTTER OPERATION
Target track
Target track, NMEA format TTM data sentence (target data fed from an ARP board-equipped MODEL1833/1833C series network radar), may be turned on or off as desired. The default setting is ON.
1. Press the [MENU] key followed by the CHART SETUP and TRACKS &
MARKS CONTROL soft keys to open the TRACK CONTROL menu.
2. Use the cursor pad to select TARGET TRACK DISPLAY.
3. Press the EDIT soft key to show the target track display window.
4. Use the cursor pad to select to ON or OFF as appropriate.
5. Press the ENTER soft key.
6. Press the [MENU] key to close the menu.
3.6.2 Stopping, restarting plotting of own ship track
When your boat is at anchor or returning to port you probably won’t need to record its track. You can stop recording the track, to conserve the track memory, as follows:
1. Press the [MENU] key followed by the CHART SETUP and TRACKS &
MARKS CONTROL soft keys to open the TRACK CONTROL menu.
TRACK
CONTROL
TRACK
CONTROL
OWN SHIP TRACK DISP
ON
OWN SHIP TRACK COLOR
RED
TARGET TRACK DISPLAY
ON
TARGET TRACK COLOR
WHITE
INTERVAL
TIME
TIME INTERVAL
00m10s
DISTANCE INTERVAL
00.10nm
MEMORY(TRACK & MARK)
2000PTS
(MARK MEMORY)
(6000)POINTS
SHIP’S TRACK STATUS
TRACKING
TRACK: 1234/2000
MARK : 9/6000
EDIT
TRACK
RESUME
ERASE
T & M
MARK
SETUP
RETURN
TRACK
RESUME
TRACK
HALT
OWN SHIP TRACK DISP
ON
OWN SHIP TRACK COLOR
RED
TARGET TRACK DISPLAY
ON
TARGET TRACK COLOR
WHITE
INTERVAL
TIME
TIME INTERVAL
00m10s
DISTANCE INTERVAL
00.10nm
MEMORY(TRACK & MARK)
2000PTS
(MARK MEMORY)
(6000)POINTS
SHIP’S TRACK STATUS
NOT TRACKING
TRACK: 1234/2000
MARK : 9/6000
EDIT
TRACK
HALT
ERASE
T & M
MARK
SETUP
RETURN
Track is plotted
Track not plotted
Track control menu (MODEL1722C series)
2. Press the TRACK RESUME soft key. The soft key now shows “TRACK
HALT” and the indication “TRACKING” in the SHIP’S TRACK STATUS window changes to “NOT TRACKING.” In addition, the icon “H” is displayed at the top of the plotter display and own ship marker becomes a hollow circle.
To restart plotting the track, press the TRACK HALT soft key.
3. Press the [MENU] key to close the menu.
3-19
3. PLOTTER OPERATION
3.6.3 Changing track color (MODEL1722C series)
Track can be displayed in red (default setting), yellow, green, light-blue, purple, blue and white. It can be useful to change track color on a regular basis to discriminate between previous day’s track, etc.
Own ship’s track
1. Press the [MENU] key followed by the CHART SETUP and TRACKS &
MARKS CONTROL soft keys to open the TRACK CONTROL menu.
2. Use the cursor pad to select OWN SHIP TRACK COLOR.
3. Press the EDIT soft key to display the track color window.
TRACK COLOR
▲
¡
¡
¡
¤
¡
¡
¡
▼
RED
YELLOW
GREEN
LIGHT BLUE
PURPLE
BLUE
WHITE
Own ship track color window
4. Use the cursor pad to select the color desired.
5. Press the ENTER soft key.
6. Press the [MENU] key to close the menu.
Target track
Like own ship’s track, target tracks can be displayed in red (default setting), yellow, green, light-blue, purple, blue and white.
1. Press the [MENU] key followed by the CHART SETUP and TRACKS &
MARKS CONTROL soft keys to open the TRACK CONTROL menu.
2. Use the cursor pad to select TARGET TRACK COLOR.
3. Press the EDIT soft key to display the track color window.
4. Use the cursor pad to select the color desired.
5. Press the ENTER soft key.
6. Press the [MENU] key to close the menu.
3-20
3. PLOTTER OPERATION
3.6.4 Track plotting method and interval for own ship track
In drawing the own ship track, first the ship’s position fed from a navigation receiver is stored into the unit’s memory at an interval of time or distance. A shorter interval provides for better reconstruction of the track, but the storage time of the track is reduced. When the track memory becomes full, the oldest track is erased to make room for the latest.
Track plotting method
Track may be plotted by time or distance interval. The default setting is “time.”
1. Press the [MENU] key followed by the CHART SETUP and TRACKS &
MARKS CONTROL soft keys to open the TRACK CONTROL menu.
2. Use the cursor pad to select INTERVAL.
3. Press the EDIT soft key to display the plot window.
INTERVAL
▲
¤
¡
▼
TIME
DISTANCE
Plot window
4. Use the cursor pad to select TIME or DISTANCE as appropriate. Distance is useful for conserving track memory, since no track is recorded when the boat is stationary.
5. Press the ENTER soft key.
6. Press the [MENU] key to close the menu.
Track plotting interval
1. Press the [MENU] key followed by the CHART SETUP and TRACKS &
MARKS CONTROL soft keys to open the TRACK CONTROL menu.
2. Use the cursor pad to select TIME INTERVAL or DISTANCE INTERVAL as appropriate.
3. Press the EDIT soft key to display the time or distance interval window, depending on what you selected at step 2.
TIME INTERVAL
Setting range: 0 min 01 sec (continuous) - 99 min 59 sec
Default setting: 10 sec
0 0m10s
(When selecting TIME INTERVAL.)
DISTANCE INTERVAL
Setting range: 00.01 nm (continuous) - 99.99 nm (km, sm)
Default setting: 0.1 nm
0 0.10nm
(When selecting DISTANCE INTERVAL.)
Interval windows
3-21
3. PLOTTER OPERATION
4. Use the [ENTER] knob and the cursor pad to enter numeric data. The
[CLEAR] key functions to clear an entire line of data.
5. Push the [ENTER] knob or ENTER soft key.
6. Press the [MENU] key to close the menu.
3.6.5 Changing own ship track/mark distribution setting
The equipment stores a total of 8000 points of track and marks. This amount may be distributed as desired, and the default setting is 2000 points of track and
6000 marks.
When you change the track memory setting all tracks and marks in the memory are erased. If necessary save the data to a memory card. For further details see paragraph “6.1.2 Saving data to a memory card”.
1. Press the [MENU] key followed by the CHART SETUP and TRACKS &
MARKS CONTROL soft keys to open the TRACK CONTROL menu.
2. Use the cursor pad to select MEMORY (TRACK & MARK).
3. Press the EDIT soft key to display the memory (track & mark) window.
TRACK MEMORY
2 000/8000 POINTS
Memory (track & mark) window
4. Use the [ENTER] knob to enter desired number of track memory points.
5. Push the ENTER soft key or [ENTER] knob. You are asked if you are sure to change the track memory capacity.
6. Push the [ENTER] knob to register setting.
7. Press the [MENU] key to close the menu.
3-22
3. PLOTTER OPERATION
This paragraph shows you how to erase own ship’s track and target tracks. You can erase ship’s track three ways: collectively, by color (color model only) and by area.
Erasing own ship track by area
You can erase own ship’s track by area as below. This function is not available on the overlay display (MODEL1722C series).
1. Press the [MENU] key followed by the CHART SETUP, TRACKS & MARKS
CONTROL and ERASE T & M soft keys to show the ERASE menu.
ERASE ALL TRACKS
ERASE TRACKS BY AREA
ERASE
EDIT
ERASE TRACKS BY COLOR
ERASE TARGET TRACKS
ERASE ALL MARKS/LINES
ERASE MARKS BY AREA
ERASE ALL TRACKS
ERASE TRACKS BY AREA
ERASE TARGET TRACKS
ERASE ALL MARKS/LINES
ERASE MARKS BY AREA
ERASE
EDIT
RETURN RETURN
SHIP’S TRACK STATUS
TRACKING
TRACK: 1234/2000
MARK : 9/6000
SHIP’S TRACK STATUS
TRACKING
TRACK: 1234/2000
MARK : 9/6000
MODEL1722C series MODEL1722 series
Erase menu
2. Use the cursor pad to select ERASE TRACKS BY AREA and press the EDIT soft key. The menu is erased and the plotter display appears.
3. Use the cursor pad to place the cursor at the top left of corner which you want to erase track from.
4. Press the START soft key or the [ENTER] knob.
5. Drag the cursor diagonally to the bottom right corner of the area which you want to erase track from.
6. Press the END soft key or the [ENTER] knob. You are asked if it is all right to delete the track.
7. Push the [ENTER] knob to delete the track selected.
8. Press the [MENU] key twice to close the menu.
3-23
3. PLOTTER OPERATION
Erasing own ship track by color (color model)
You may erase own ship’s track by color as follows:
1. Press the [MENU] key followed by the CHART SETUP, TRACKS & MARKS
CONTROL and ERASE T & M soft keys to show the ERASE menu.
2. Use the cursor pad to select ERASE TRACKS BY COLOR and press the
EDIT soft key.
ERASE TRK BY COLOR
▲
¡
¡
¡
¤
¡
¡
¡
▼
RED
YELLOW
GREEN
LIGHT BLUE
PURPLE
BLUE
WHITE
Erase track by color window
3. Use the cursor pad to select the color you want to erase and push the
[ENTER] knob or ENTER soft key. You are asked if it is all right to delete the track.
4. Push the [ENTER] knob to erase track color selected.
5. Press the [MENU] key twice to close the menu.
Erasing all own ship track
1. Press the [MENU] key followed by the CHART SETUP, TRACKS & MARKS
CONTROL and ERASE T & M soft keys to show the ERASE menu.
2. Use the cursor pad to select ERASE ALL TRACKS and press the EDIT soft key.
3. Push the [ENTER] knob to erase all own ship track.
4. Press the RETURN soft key.
5. Press the [MENU] key to close the menu.
Erasing all target tracks
1. Press the [MENU] key followed by the CHART SETUP, TRACKS & MARKS
CONTROL and ERASE T & M soft keys to show the ERASE menu.
2. Use the cursor pad to select ERASE TARGET TRACKS and press the EDIT soft key.
3. Push the [ENTER] knob to erase all target tracks.
4. Press the [MENU] key twice to close the menu.
3-24
3. PLOTTER OPERATION
Marks are useful for denoting important points such as a good fishing spot.
Marks can be inscribed in seven shapes and seven colors (MODEL1722C series): Red, yellow, green, light-blue, purple, blue and white.
¡
✕
Mark shapes
3.7.1 Entering a mark
1. Place the cursor on the location where you want a mark to appear.
2. Press the MARK ENTRY soft key. (Press the [HIDE/SHOW] key if the plotter soft keys are not shown.)
The mark is inscribed in the size and shape selected on the MARKS & LINES menu. The default mark attributes are size, normal; color (MODEL1722C series), yellow, and shape, hollow circle (
○
).
3.7.2 Changing mark attributes
You can select the shape and for marks on the MARKS & LINES menu.
1. Press the [MENU] key to show the menu.
2. Press the CHART SETUP, TRACKS & MARKS CONTROL and MARK
SETUP soft keys to show the MARKS & LINES menu.
MARKS &
LINES
MARKS &
LINES
MARKS/LINES COLOR
YELLOW
MARKS SHAPE
¡
LINES STYLE
.
MARKS SIZE
LARGE
EDIT
MARKS SHAPE
¡
LINES STYLE
.
MARKS SIZE
LARGE
EDIT
RETURN
SHIP’S TRACK STATUS
TRACKING
TRACK: 1234/2000
MARK : 9/6000
RETURN
SHIP’S TRACK STATUS
TRACKING
TRACK: 1234/2000
MARK : 9/6000
MODEL1722C series MODEL1722 series
Marks & lines menu
3. For the MODEL1722C series, do the following to select mark and line color.
Select MARKS/LINES COLOR and press the EDIT soft key.
Use the cursor pad to choose color desired and press the ENTER soft key.
3-25
3. PLOTTER OPERATION
4. Select MARKS SHAPE and press the EDIT soft key.
MARK SHAPE
▲
¡
¡
¡
¡
¤ ¡
¡
¡
✕
▼
Mark shape window
5. Use the cursor pad to select mark shape desired and then press the
RETURN soft key.
6. Select MARKS SIZE and press the EDIT soft key.
7. Use the cursor pad to select LARGE (default setting) or SMALL as appropriate.
8. Press [ENTER] knob or ENTER soft key.
9. Press the [MENU] key twice to close the menu.
3.7.3 Selecting line type
You may inscribe lines to denote good fishing spots, areas of special interest, etc.
You can even construct simple charts.
1. Press the [MENU] key followed by the CHART SETUP, TRACKS & MARKS
CONTROL and MARKS SETUP soft keys to show the MARK & LINES menu.
MARKS &
LINES
MARKS &
LINES
MARKS/LINES COLOR
YELLOW
MARKS SHAPE
¡
LINES STYLE
.
MARKS SIZE
LARGE
EDIT
MARKS SHAPE
¡
LINES STYLE
.
MARKS SIZE
LARGE
EDIT
SHIP’S TRACK STATUS
TRACKING
TRACK: 1234/2000
MARK : 9/6000
RETURN
SHIP’S TRACK STATUS
TRACKING
TRACK: 1234/2000
MARK : 9/6000
MODEL1722C series
Marks & lines menu
MODEL1722 series
2. Select LINE STYLE and press the EDIT soft key.
RETURN
3-26
3. PLOTTER OPERATION
LINES STYLE
▲
¤
¡
¡
¡
▼
- - - -
Mark line window
3. Use the cursor pad to select line style desired and press the ENTER soft key.
Line style “dot” disables line drawing. The joint between lines is determined by mark shape. For example, selecting the circle shape will join lines with a circle as below.
4. Press the [MENU] key to close the menu.
Erasing an individual mark
1. Operate the cursor pad to place the cursor on the mark you want to erase.
2. Press the [CLEAR] key to erase the mark.
Erasing an individual line
1. Place the cursor on an end of the line to erase and press the [CLEAR] key.
2. Placing the cursor at the intersecting point of two line segments will erase both line segments.
Erasing marks, lines by area
This function is not available on the overlay area (MODEL1722C series).
1. Press the [MENU] key followed by the CHART SETUP, TRACKS & MARKS
CONTROL and ERASE T & M soft keys to show the ERASE menu.
2. Use the cursor pad to select ERASE MARKS BY AREA and press the EDIT soft key. The menu is erased and the plotter display appears.
3. Use the cursor pad to place the cursor at the top left-hand corner of the area which is to enclose the marks/lines to erase.
4. Press the START soft key or the [ENTER] knob.
5. Drag the cursor to the bottom right-hand corner of the area which is to enclose the marks/lines to erase.
6. Press the END soft key or the [ENTER] knob. You are asked if it is all right to delete the marks/lines selected. Press the [ENTER] knob to delete.
7. Press the [MENU] key to close the menu.
3-27
3. PLOTTER OPERATION
Erasing all marks, lines
You can erase all marks and lines. Be absolutely sure you want to erase all marks and lines - erased marks and lines cannot be restored.
1. Press the [MENU] key followed by the CHART SETUP, TRACKS & MARKS
CONTROL and ERASE T & M soft keys to show the ERASE menu.
2. Use the cursor pad to select ERASE ALL MARKS/LINES and press the EDIT soft key.
3. Push the [ENTER] knob to erase all marks and lines.
4. Press the [MENU] key twice to close the menu.
3-28
3. PLOTTER OPERATION
3.8 Waypoints
In navigation terminology, a waypoint is a particular location on a voyage whether it be a starting, intermediate or destination point. A waypoint is the simplest piece of information your equipment requires to get you to a destination, in the shortest distance possible.
This unit has 999 waypoints into which you can enter position information. You may enter a waypoint five ways: at own ship position, at MOB position
(page3-61), by cursor, by range and bearing, and through the waypoint list
(manual input of latitude and longitude).
Entering a waypoint at own ship position
Press the [SAVE/MOB] key momentarily to store your position as a waypoint.
This new waypoint will automatically be saved in the waypoint list, under the youngest empty waypoint number.
Entering a waypoint with the cursor
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES, WAYPOINTS and WAYPOINT BY
CURSOR soft keys. The plotter display appears.
3. Operate the cursor pad to place the cursor on the location desired.
4. Press the NEW WPT soft key. The waypoint window appears and it shows waypoint mark shape, waypoint name, comment (default: time and date), position of waypoint and proximity alarm radius.
NEW
WPT
MARK NAME
34
°
0 0 1 W P T
135
°
21.000'W
°
0.00nm
COMMENT
002WPT
0 2 : 3 6 0 1 J A N 0 1
00:00 01JAN00
POSITION
L A T
°
21.000'W
359.9
°
0.00nm
003WPT
L O N
1 3 4
34
°
00:00 01JAN00
°
44.000'N
1 2 . 3 4 5 ' W
135
°
21.000'W
359.9
0.00nm
SELECT
MARK
COORD
TYPE
N < - -> S
E < - -> W
SAVE
RETURN
PROXIMITY ALARM RADIUS
0 . 0 0 n m
Waypoint window
5. If you do not need to change the waypoint data, press the SAVE soft key to register the waypoint. The steps which follow show you how to change waypoint data.
6. For the color model, press the SELECT MARK soft key.
3-29
3. PLOTTER OPERATION
7. Press the MARK SHAPE soft key to open the mark shape selection window.
SELECT MARK
Waypoint mark shape selection window
8. Operate the cursor pad to select shape desired.
9. Press the ENTER soft key.
10. For the MODEL1722C series, press the SELECT MARK and MARK
COLOR soft keys in that order to open the waypoint mark color selection window. Select color desired and press the ENTER soft key.
SELECT COLOR
▲
¡
¡
¡
¤
¡
¡
¡
▼
RED
YELLOW
GREEN
LIGHT BLUE
PURPLE
BLUE
WHITE
Waypoint mark color selection window
Note: You cannot change the shape and color of a waypoint when the proximity alarm radius for it is other than “zero.” To change shape or color, enter all zeroes as the proximity alarm radius.
11. You can change the name (1 to 6 characters), comment (13 characters), L/L position and the proximity alarm radius for a waypoint as follows: a) Use the cursor pad to select the NAME, COMMENT, POSITION or
PROXIMITY ALARM RADIUS field. (“Proximity alarm radius” provides for visual and aural alarms when your boat nears a waypoint by the distance specified. A circle with a diagonal line through it marks any waypoint for which its proximity alarm radius is other than zero.) b) Use the cursor pad to select location. c) Rotate the [ENTER] knob to select appropriate alphanumeric character.
3-30
3. PLOTTER OPERATION
12. Press the SAVE soft key to register the waypoint.
13. Enter another waypoint with the cursor, or press the [MENU] key to close the menu.
Entering a waypoint by range and bearing
This method is useful when you want to enter a waypoint using range and bearing to a target found on a radar.
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES, WAYPOINTS and WAYPOINT BY RNG &
BRG soft keys.
3. An “X” (red on the MODEL1722C series) appears at own ship position, and it is the origin point for range and bearing. Operate the cursor pad to place the cursor on the location desired. Range and bearing from own ship to the cursor appear at the top of the display.
Note: The origin point of range and bearing can be shifted to the location desired. Operate the cursor pad to select location, and then press the
START POINT soft key.
4. Press the NEW WPT soft key. The waypoint window appears and it shows mark shape, waypoint name, comment (default: date and time), position of waypoint and proximity alarm radius.
NEW
WPT
MARK NAME
34
°
0 0 1 W P T
135
°
21.000'W
COMMENT
002WPT
°
0.00nm
POSITION
L A T
°
00:00 01JAN00
21.000'W
359.9
°
0.00nm
SELECT
MARK
COORD
TYPE
N < - -> S
E < - -> W
L O N
1 3 4
34
°
00:00 01JAN00
°
1 2 . 3 4 5 ' W
135
°
21.000'W
359.9
0.00nm
SAVE
RETURN
PROXIMITY ALARM RADIUS
0 . 0 0 n m
Waypoint window
5. If necessary, change waypoint data following the instructions from step 6 in
“Entering a waypoint with the cursor” on page 3-29.
6. Press the SAVE soft key to register the waypoint. To enter another waypoint with the cursor select desired location with the cursor pad and press the
NEW WPT soft key.
7. Press the [RETURN] key to close the menu.
3-31
3. PLOTTER OPERATION
Entering a waypoint from the waypoint list
You can manually enter waypoint position from the waypoint list as follows:
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES and WAYPOINTS soft keys.
3. Press the LOCAL LIST (lists waypoints in order from nearest to furthest) or
ALPHANUMERIC LIST (lists waypoints in alphanumeric order) soft key.
ABALONE
00:00 01JAN01
35
°
47.010'N
135
°
21.000'W
350.9
°
3.80 nm
CRAB
00:00 01JAN01
34
°
42.000'N
135
°
21.050'W
050.9
°
1.98 nm
FISH
135
°
34
°
41.000'N
21.030'W
065.9
°
1.83 nm
LOBSTER
00:00 01JAN01
38
°
44.300'N
135
°
21.010'W
144.9
°
4.93nm
PUSH ENTER KNOB TO
SEARCH FOR
--
WPT
ALPHA
GOTO
NEW
WPT
EDIT
WPT
ERASE
WPT
RETURN
FISH
135
°
34
°
41.000'N
21.030'W
065.9
°
1.83 nm
CRAB
00:00 01JAN01
34
°
42.000'N
135
°
21.050'W
050.9
°
1.98 nm
ABALONE
00:00 01JAN01
35
°
47.010'N
135
°
21.000'W
350.9
°
3.80 nm
LOBSTER
00:00 01JAN01
38
°
135
°
44.300'N
21.010'W
144.9
°
4.93nm
WPT
LOCAL
GOTO
NEW
WPT
EDIT
WPT
ERASE
WPT
RETURN
Alphanumeric waypoint list Local waypoint list
Alphanumeric and local waypoint lists
4. Press the NEW WPT soft key to show the waypoint window (see the figure on the previous page). Own ship position is shown in the position box.
5. Select the position box and enter waypoint position desired, using the cursor pad to select location and rotating the [ENTER] knob to enter digit.
6. If desired change waypoint data following the instructions from step 6 in
“Entering a waypoint with the cursor” on page 3-29.
7. Press the SAVE soft key to register the waypoint.
8. Press the [MENU] key to close the menu.
Waypoint data may be edited from the waypoint list or directly from the plotter display.
Editing waypoint data from the waypoint list
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES and WAYPOINTS soft keys.
3. Press the LOCAL LIST or ALPHANUMERIC LIST soft key as appropriate.
4. Use the cursor pad to select the waypoint you want to edit.
5. Press the EDIT WPT soft key.
6. Edit waypoint as appropriate.
3-32
3. PLOTTER OPERATION
7. Press the SAVE soft key.
8. Press the [MENU] key to close the menu.
Editing a waypoint from the plotter display
You may change edit waypoints from the plotter display as follows:
1. Press the [MENU] key followed by the WAYPOINTS/ROUTES and
WAYPOINTS soft key to open the waypoint menu.
2. Press the WAYPOINT BY CURSOR soft key.
3. Operate the cursor pad to place the cursor on the waypoint which you want to change. A flashing diamond mark appears on the waypoint when it is correctly selected.
4. Press the EDIT/MOVE soft key. Three soft keys replace the EDIT/MOVE soft key:
EDIT WPT: Edit from the waypoint entry window.
MOVE WPT: Move waypoint to new position with the cursor.
ERASE WPT:
Erase waypoint, see paragraph 3.8.3.
5. Press appropriate soft key. If you pressed the EDIT WPT soft key the waypoint entry window appears; edit data as appropriate. For MOVE WPT do the following: a) Operate the cursor pad to place the cursor on the location desired for the waypoint. A line connects previous position and new position. b) Push the [ENTER] knob. The waypoint moves to the cursor position and its new position is recorded on the waypoint list. If the waypoint is set as destination or is part of a route, you are asked if you are sure to move the waypoint. In this case, push the [ENTER] knob to move the waypoint, or press the [CLEAR] key to cancel.
7. Press the MENU key to finish.
Range and bearing from own ship to cursor
+ 34
°
22. 3456'N 359.9
°
M TRIP NU
080 ° 22. 3456'E 59.9 nm 99.9 nm
16.0nm
(1) Select waypoint to move,
then press EDIT/MOVE
and MOVE WPT soft keys.
(2) Drag cursor to new position,
then push the [ENTER] knob.
WP-002
FISH
BRIDGE
RNG
BRG
CANCEL
Press to alternately display range/bearing from own ship to cursor, range/bearing from original waypoint position to cursor position.
Below is an example of the range/bearing from original waypoint position to cursor position.
+ 34
°
22. 3456’N FROM 5.3
°
M
080
°
22. 3456’E FISH 1.45 nm
Plotter display
3-33
3. PLOTTER OPERATION
Erasing a waypoint with the cursor
1. Press the cursor pad to turn on the cursor.
2. Operate the cursor pad to place the cursor on the waypoint you want to erase.
A flashing diamond mark appears over the waypoint when the waypoint is correctly selected.
3. Press the [CLEAR] key. You are asked if you are sure to erase the waypoint.
4. Push the [ENTER] knob. The waypoint is erased from both the plotter screen
(if it is currently displayed) and the waypoint list.
Note: You may also erase a waypoint while the waypoint menu is active as follows: a) Place the cursor on the waypoint to erase. b) Press the EDIT/MOVE soft key. c) Press the ERASE WPT soft key followed by the [ENTER] knob. d) Press the RETURN soft key to finish.
Erasing a waypoint from the waypoint list
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES and WAYPOINTS soft keys.
3. Press the LOCAL LIST or ALPHANUMERIC LIST soft key.
4. Use the cursor pad to select the waypoint you want to erase.
5. Press the ERASE WPT soft key. You are asked if you are sure to erase the waypoint.
6. Push the [ENTER] knob. The waypoint is erased from both the waypoint list and the plotter screen (if it is currently displayed).
7. Press the [MENU] key to close the menu.
3-34
3. PLOTTER OPERATION
3.8.4 Changing waypoint mark size (FURUNO, NavCharts™)
You may change the size of all waypoint marks to small or large (default), or you may turn them off.
1. Press the [MENU] key to open the menu.
2. Press the CHART SETUP and CHART DETAILS soft keys.
CHART
DETAILS
CHART
DETAILS
LAT LON GRID
GREEN
TEXT INFORMATION
ON
WAYPOINTS
LARGE
WAYPOINT NAMES
ON
CHART BORDER LINES
ON
LANDMASS
BRT YELLOW
BACKGROUND
BLUE
NAVAIDS
ON
LIGHT SECTOR INFO
ON
OTHER SYMBOLS
WHITE
MARKS SIZE
LARGE
EDIT
CNTOUR
LINE
RETURN
LAT LON GRID
ON
TEXT INFORMATION
ON
WAYPOINTS
LARGE
WAYPOINT NAMES
ON
CHART BORDER LINES
ON
LANDMASS
ON
NAVAIDS
ON
LIGHT SECTOR INFO
ON
OTHER SYMBOLS
ON
MARKS SIZE
LARGE
EDIT
CNTOUR
LINE
RETURN
MODEL1722C series MODEL1722 series
Chart details menu
3. Use the cursor pad to select WAYPOINTS.
4. Press the EDIT soft key.
5. Use the cursor pad to select LARGE, SMALL or OFF.
LARGE: Shows mark in actual shape.
SMALL: Displays all waypoints with an “X” regardless of mark shape selected.
OFF: Turns off all waypoints and their names. Waypoints which are part of a route are always shown regardless of this setting.
6. Press the ENTER soft key or [ENTER] knob to register your selection.
7. Press the [MENU] key to close the menu.
3-35
3. PLOTTER OPERATION
You can search for a waypoint through the alphanumeric list as follows:
1. Press the [MENU] key.
2. Press the WAYPOINTS/ROUTES, WAYPOINTS and ALPHANUMERIC LIST soft keys to show the alphanumeric list.
WPT
ALPHA
ABALONE
00:00 01JAN01
35
°
47.010'N
135 ° 21.000'W
350.9
°
3.80 nm
CRAB
00:00 01JAN01
34 ° 42.000'N
135
°
21.050'W
050.9
°
1.98 nm
FISH
00:00 01JAN01
34
°
41.000'N
135
°
21.030'W
065.9
°
1.83 nm
LOBSTER
00:00 01JAN01
38 ° 44.300'N
135
°
21.010'W
144.9
°
4.93nm
PUSH ENTER KNOB TO
SEARCH FOR
--
GOTO
NEW
WPT
EDIT
WPT
ERASE
WPT
RETURN
Search window
Alphanumeric list
3. Use the cursor pad and [ENTER] knob to enter up to three alphanumeric characters in the search window. Then, the waypoint searched appears at the top of the screen.
4. Press the [MENU] key to close the menu.
3-36
3. PLOTTER OPERATION
3.9 Routes
Often a trip from one place to another involves several course changes, requiring a series of route points (waypoints) which you navigate to, one after another. The sequence of waypoints leading to the ultimate destination is called a route. Your unit can automatically advance to the next waypoint on a route, so you do not have to change the destination waypoint repeatedly.
You can store up to 200 routes, and a route may have 35 waypoints.
Entering a route with existing waypoints
This method constructs routes using existing waypoints.
1. Press the [MENU] key.
2. Press the WAYPOINTS/ROUTES soft key.
3. Press the ROUTES soft key to open the route menu. (No data will be shown if there is no routes created.)
Total length of route
Route name
001
LENGTH
25.6 nm
WAYPOINTS
35
002
LENGTH WAYPOINTS
56.7 nm
2
003
LENGTH
21.1 nm
WAYPOINTS
3
004
LENGTH WAYPOINTS
21.1 nm
3
PUSH ENTER KNOB TO
SEARCH FOR
--
ROUTE
GOTO
NEW
ROUTE
EDIT
ROUTE
ERASE
ROUTE
RETURN
Number of waypoints in route
Route menu
4. Press the NEW ROUTE soft key to open the new route entry screen.
NEW
ROUTE
ROUTE NAME
0 0 1
PLOT
COMMENT
LOCAL
LIST
ALPHA
LIST
CONECT
ROUTE
CANCEL
New route entry screen
3-37
3. PLOTTER OPERATION
5. If desired you can change the route name shown and/or add a comment. A route name may consist of six characters; comment, 13 characters.
6. Press the LOCAL LIST or ALPHA LIST soft key to open the waypoint list.
7. Use the cursor pad to select a waypoint, and press the ADD WPT soft key to add it to the route.
8. Repeat step 7 to complete the route.
Note: To clear a waypoint, press the ERASE LST WP soft key. Each pressing of this key deletes the last waypoint entered.
9. Press the SAVE soft key to register the route.
10. Press the [MENU] key to close the menu.
Entering a route with the cursor
This method allows you to construct a route directly on the plotter display, using existing waypoints or new locations. Any new location will be saved as a waypoint, under the youngest empty waypoint number.
1. Follow step 1-5 in “Entering a route from the route list” on the previous page.
2. Press the PLOT soft key to show the plotter display.
3. Operate the cursor pad to place the cursor on an existing waypoint (ADD
WPT soft key appears) or new location (ADD NEW WPT soft key appears).
4. Press the ADD WPT soft key (or ADD NEW WPT soft key).
5. Repeat steps 3 and 4 to complete the route.
6. Push the [ENTER] knob to register the route.
7. Press the MENU key to close the menu.
3-38
3. PLOTTER OPERATION
Creating voyage-based routes
You can create routes based on your ship’s track, and each route may contain
35 points. The route can be created automatically (by time or distance), or manually. This feature is useful when you wish to retrace previous track.
The “SAVE” icon appears at the top of the screen when a voyage-based route is being created.
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES soft key.
3. Press the CREATE VOYAGE-BASED ROUTE soft key.
001
LENGTH
25.6 nm
WAYPOINTS
35
002
LENGTH
56.7 nm
WAYPOINTS
2
003
LENGTH
WAYPOINTS
21.1 nm 3
004
LENGTH
21.1 nm
WAYPOINTS
3
ROUTE
NEW
SELECT
ROUTE
RETURN
PUSH ENTER KNOB TO
SEARCH FOR
--
Save route menu
4. Press the NEW soft key to show the new route window.
Note: If you want to tack voyage-based points on an existing route, press the SELECT ROUTE soft key instead of the NEW soft key, then enter route number to use.
Next consecutive route number
ROUTE NAME
0 0 6
COMMENT
SAVE
ROUTE
BCKTRK
TIME
BCKTRK
DIST
MANUAL
USE FURUNO BACK TRACK FUNCTION
TO AUTOMATICALLY CREATE ROUTE
BY TIME OR DISTANCE.
CANCEL
Save route window
5. If required, you may change the route name and enter a comment.
3-39
3. PLOTTER OPERATION
6. Choose how to record points for your route, by time, by distance or manual entry pressing by one of BCKTRK TIME, BCKTRK RANGE or MANUAL soft key as appropriate. For manual go to step 8. For BCKTRK TIME, BCKTRK
DIST one of the following displays appears.
TIME INTERVAL DISTANCE INTERVAL
0 0h01m 0 0.1nm
(When selecting BCKTRK TIME.) (When selecting BCKTRK DIST.)
Displays for entry of time, distance interval
7. Enter interval desired with the cursor pad and press the [ENTER] knob.
Press the START and RETURN soft keys followed by the [MENU] key to close the menu. At this moment, voyage based route will be created.
8. For manual entry of waypoints, do the following: a) Press the [SAVE/MOB] key momentarily to enter a waypoint mark at own ship position. A new waypoint is created under the next consecutive waypoint number and that waypoint is added to the route. (You may close the SAVE ROUTE screen by pressing the RETURN soft by followed by the MENU key.) b) Repeat step a) as necessary. 35 waypoints may be entered.
To stop recording waypoints and save the route
You can stop recording waypoints and save the route at any time as shown in the procedure below. When 35 waypoints have been entered the message “Total
35 WPTS have been already registered in the route. Stop creating voyage based route.” is displayed. In this case, save the route as shown below.
1. Press the [MENU] key followed by the WAYPOINTS/ROUTES and CREATE
VOYAGE-BASED ROUTE soft keys.
2. Press the FINISH LOG soft key to stop recording waypoint and save the route.
3. Press the [MENU] key to close the menu.
3-40
3. PLOTTER OPERATION
Two routes which you have created can be connected as follows to form a new route.
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES soft key.
3. Press the ROUTES soft key.
4. Press the NEW ROUTE soft key.
5. If desired, enter the name for the new route and enter comment.
6. Press the CONNECT soft key.
7. Use the cursor pad and the [ENTER] knob to enter the route name for the first route, beneath FIRST in the CONNECT ROUTE window.
NEW
ROUTE ROUTE NAME
0 0 1
F < -- > R
COMMENT
CONNECT ROUTE
FIRST SECOND
_ _ _ _ _ _ _ _ _ _ _ _
FORWARD FORWARD
SAVE
CANCEL
Connect route window
8. If necessary press the F< - ->R soft key to select direction to follow the waypoints of the route, forward or reverse.
9. Enter the route name of the second route as you did for the first route.
10. Press the SAVE soft key.
11. Press the [MENU] key to close the menu.
Note: The maximum number of waypoints in a route is 35. If this number is exceeded an error message appears. In this case, delete waypoints in one or both routes so the total number of waypoints does not exceed 35.
3-41
3. PLOTTER OPERATION
Waypoints can be inserted into a route as follows:
Inserting waypoint from the route list
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES soft key.
3. Press the ROUTES soft key.
4. Use the cursor pad to select a route.
5. Press the EDIT ROUTE soft key. The route name screen appears.
6. Press the LOCAL LIST soft key.
EDIT
ROUTE
INSERT
WPT
ROUTE NAME: 001
COMMENT:
01 001WPT
34
°
44.111'N
135
°
21.134'W
02 003WPT
34 ° 43.432'N
135 ° 41.456'W
03
002WPT
34 ° 14.124'N
135 ° 21.567'W
04 005WPT
34
°
44.569'N
135
°
21.152'W
05 008WPT
34
°
54.124'N
135
°
21.888'W
LEG
29.9
°
12.0nm
159.9
°
6.00nm
50.5
°
29.8nm
359.9
°
3.0nm
REMOVE
WPT
CHANGE
WPT
COORD
TYPE
RETURN
Edit route menu
7. Press or ▼ to place the cursor at the location where you want to insert a waypoint.
8. Press the INSERT WPT or CHANGE WPT soft key as appropriate. The local list appears.
LOCAL LIST
001
002
003
004
001WPT
34
°
44.111'N
135
°
21.134'W
002WPT
34
°
43.432'N
135
°
41.456'W
003WPT
34
°
14.124'N
135
°
21.567'W
004WPT
34
°
34.490'N
135
°
51.387'W
Waypoint list for editing a route (local list)
3-42
3. PLOTTER OPERATION
9. Use the cursor pad to select the waypoint you want to insert. (You can switch between the local list and alphanumeric list by using the LOCAL LIST and
ALPHA LIST soft keys.)
10. Press the SELECT WPT or CHANGE WPT soft key, whichever is displayed.
11. Press the [MENU] key to close the menu.
Inserting a waypoint from the plotter display
Inserting a waypoint before first or last waypoint in a route
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES soft key.
3. Press the ROUTES soft key.
4. Use the cursor pad to select a route.
5. Press the EDIT ROUTE soft key.
6. Press the PLOT soft key to show the plotter screen.
7. Operate the cursor to place the cursor on the first (or last) waypoint of the route. A flashing diamond appears when the waypoint is correctly selected.
8. Press the ADD TO START soft key or the ADD TO END soft key depending on the waypoint you selected at step 7.
9. Operate the cursor pad to place the cursor on an existing waypoint (ADD
WPT soft key appears) or new location (ADD NEW WP soft key appears).
10. Press the ADD WPT soft key (ADD NEW WP soft key).
11. Press the [MENU] key to close the menu.
Inserting a waypoint in an intermediate location on a route
1. Follow steps 1 through 6 in “Inserting a route waypoint before the first or last waypoint in a route.”
2. Operate the cursor pad to place the cursor on a line connecting waypoints.
The SPLIT LEG soft key appears and the line flashes when the line is correctly selected.
3. Press the SPLIT LEG soft key. The line changes from solid to dashed.
4. The INSERT NEW WP soft key appears. Dray the cursor to a new location or select an existing waypoint, in which case the INSERT WPT key replaces the
INSERT NEW WP key.
5. Press the INSERT WPT soft key (INSERT NEW WP soft key).
6. Press the [MENU] key to close the menu.
3-43
3. PLOTTER OPERATION
3.9.4 Removing waypoints from a route
Removing a waypoint from the route list
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES soft key.
3. Press the ROUTES soft key.
4. Select a route.
5. Press the EDIT ROUTE and LOCAL LIST soft keys.
6. Select the waypoint you want to remove.
7. Press the REMOVE WPT soft key.
8. Press the [MENU] key to close the menu.
Removing a waypoint from the plotter display
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES soft key.
3. Press the ROUTES soft key.
4. Select a route.
5. Press the EDIT ROUTE soft key.
6. Press the PLOT soft key to show the plot screen.
7. Operate the cursor pad to place the cursor on the waypoint you want to remove from the route.
8. Press the REMOVE WPT soft key. The route is redrawn, eliminating the waypoint erased.
9. Press the [MENU] key to close the menu.
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES soft key.
3. Press the ROUTES soft key.
4. Use the cursor pad to select a route.
5. Press the ERASE ROUTE soft key. You are asked if you are sure to erase the route.
6. Push the [ENTER] knob to erase the route, or the [CLEAR] key to escape.
7. Press the [MENU] key to close the menu.
3-44
3. PLOTTER OPERATION
3.10 Navigation
This section shows you how to get to a desired destination by “quick points,” waypoints, port services and routes.
Note : Reciprocal setting and canceling of destination is available by outputting the data sentence ZDA from the NavNet unit connected to the navigator.
3.10.1 Navigating to a “quick point”
The “quick point” feature allows you to navigate to point(s) without retaining the data indefinitely in your unit’s memory.
Selecting quick point entry method
You need to tell your unit how to set the quick point: 1POINT, 35POINTS (up to
35 points) or 35PTS/PORT SVC. (For how to navigate to points/port services see “3.10.3 Navigating to ports, port services” on page 3-47.)
1. Press the [MENU] key.
2. Press the PLOTTER SETUP soft key.
3. Use the cursor pad to select SET GOTO METHOD and press the EDIT soft key.
GOTO METHOD
¤
¡
1POINT
35POINTS
¡ 35PTS/PORT SVC
Goto method window
4. Use the cursor pad to select method desired.
5. Press the ENTER soft key.
6. Press the [MENU] key to close the menu.
Navigating to a single quick point
1. Place the cursor on an existing waypoint (GOTO WPT soft key appears) or a new location (GOTO CURSOR soft key appears).
2. Select “1 POINT” following the procedure in the above paragraph.
3. Depending on the selection you made at step 1 press GOTO CURSOR or
GOTO WPT soft key.
A solid line (light-blue on the MODEL1722C series) with arrows connects between own ship and destination, which is marked as “QP<01>” for cursor-selected location or waypoint name in case of waypoint. Arrows on the line show the direction to follow to get to the point. Range and bearing from own ship to the destination appear at the top of screen. The quick point is saved to the waypoint list as waypoint “QP01.”
3-45
3. PLOTTER OPERATION
Navigating to multiple quick points
1. Select “35 POINTS” following the procedure in “Selecting quick point entry method” on the previous page.
2. Press the GOTO soft key.
3. Place the cursor on an existing waypoint (SELECT WPT soft key appears) or a new location (ADD QP soft key appears).
4. Depending on the action taken at step 3 press the SELECT WPT or ADD QP soft key. “QP<01>” appears at the cursor location if a quick point is selected.
To erase last-entered quick point (waypoint), press the ERASE LST QP
(ERASE LST WP) soft key.
5. Repeat steps 3 and 4 to complete the route.
6. Push the [ENTER] knob to finish.
A solid line runs between own ship and first waypoint and a dashed line between other waypoints. (For the MODEL1722C series, those lines are colored light-blue and green, respectively.) Quick points are numbered in sequential order from
QP<01> and are saved to the waypoint list. Range and bearing from own ship to the first destination appear at the top of screen. The quick points are saved as a route, under the name “Q>RTE” (Quick Route).
Selecting waypoint from the plotter display
1. Operate the cursor pad to select a waypoint.
2. Press the GOTO WPT soft key.
Note: GOTO method should be selected to “1 POINT” on the PLOTTER SETUP menu.
Selecting waypoint from the waypoint list
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES soft key.
3. Press the WAYPOINTS soft key to open the waypoint menu.
4. Press the LOCAL LIST or ALPHANUMERIC LIST soft key as desired.
5. Use the cursor pad to select a waypoint.
6. Press the GOTO soft key, and the plotter display appears.
For either of the above methods, a solid line (light-blue on the MODEL1722C series) runs between waypoint selected and own ship’s position. Arrows on the line show the direction to the follow to get to the waypoint. Waypoint data appears at the top of screen.
3-46
3. PLOTTER OPERATION
3.10.3 Navigating to ports, port services (NavCharts ™ only)
Some NavCharts ™ have a port service list which shows services available at ports or harbors. (See page 3-13.) You can use the list to set destination as follows:
1. Select “35 PTS/PORT SVC” following the procedure in “Selecting quick point entry method” on page 3-45.
2. Press the GOTO soft key. Then, soft key titles change as in the figure below.
+
40
°
45.971'N
13
°
57.462'E
16.0nm
FROM
OS
0.26 nm
180.2
°
M
GOTO
QUICK
ROUTE
NEAR
SRVC
PORT
PUNTA CORNACCHIA
ACCO AMENO
ISCHIA
PORTO
CASAMICCIOLA
I. ISCHIA
CANCEL
GOTO
Plotter display
3. Press the PORT or NEAR SRVC soft key depending on objective. PORT shows a list of ports in your area. NEAR SRVC displays the port service list.
¤
¡
PORT & SERVICE
¡
¡
PORT & SERVICE
ACCIAROLI
ACQUAMORTA
AGNONE S. NICOLA
AGROPOLI
AMALFI
BAIA
CAPRI
CASA MICCIOLA-ISCHIA
Port list (Italy)
¡ ¡
¡ ¡
▼
Port services
Port services and sample port list
3-47
3. PLOTTER OPERATION
4. If you selected PORT at step 3, use the cursor pad to select a port and press the ENTER soft key. Make a route using the soft keys and push the
[ENTER] knob. (If you want to go directly to that port, simply press the ADD
QP soft key followed by the [ENTER] knob.)
If you selected NEAR SRVC at step 3, select service mark desired and then push the ENTER soft key or [ENTER] knob. Then, the display shows the locations of those services nearest you. (The figure below shows the location of filling stations in an area in southern Italy.) Use the cursor pad to place the “hand cursor” on the port service icon desired and press the
ENTER soft key. Make a route using the soft keys and push the [ENTER] knob. (If you want to go directly to location selected, simply press the ADD
QP soft key followed by the [ENTER] knob.)
+
40
°
45.971'N
13
°
57.462'E
FROM
OS
0.26 nm
180.2
°
M
GOTO
16.0nm
ENTER
PUNTA CORNACCHIA
ACCO AMENO
ISCHIA
PORTO
CASAMICCIOLA
I. ISCHIA
CANCEL
GOTO
Sample filling station locations (southern Italy)
3-48
3. PLOTTER OPERATION
3.10.4 Following a route
Selecting the route to follow
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES soft key.
3. Press the ROUTES soft key to open the route list.
4. Select a route.
5. Press the GOTO soft key to show the plotter display. The cursor is on the route waypoint nearest own ship.
WPT
FISH
FROM
OS
1.3 nm
208.5
°
M
GOTO
ROUTE
16.0 nm
WP-002
WP-001
FISH
CRAB
GOTO
WPT
RVRSE
ROUTE
RETURN
Plotter display, route selected as destination
6. Operate the cursor pad to place the cursor on the waypoint or leg in the route from where to start navigating the route.
7. Press the GOTO WPT or FOLLOW LEG soft key, depending on the action taken at step 6.
A solid line runs between own ship and the first route waypoint and all other route waypoints are connected with a dashed line. (For the 1722C series, those lines are colored light-blue and green, respectively.) The arrows on the lines show the direction to traverse the route.
Navigating route waypoints in reverse order
Press the RVRSE ROUTE soft key to navigate waypoints in reverse order. The arrows on the route line point in the direction selected.
3-49
3. PLOTTER OPERATION
Restarting navigation
When you steer to avoid an obstacle or the vessel drifts, you may go off your intended course, as in Line 1 in the figure below. Also, if you don’t need to return to the original course, you can go directly to the next waypoint, as in Line 2 in the figure below. In these cases, use the restart function to restart navigation.
Line 2
3-50
Obstacle
Line 1
Original course
Example of when to restart navigation
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES soft key.
3. Press the LOG soft key.
Destination waypoint (WPT name against bright background)
Passed waypoint (green characters)
Estimated Time of Arrival at destination
LOG
Replaces triangle when selecting a route leg.
ETA 23:59 11.FEB
01 001WPT
34
135
° 44.111'N
21.134'W
02 003WPT
34
135
° 43.432'N
41.456'W
03 002WPT
34
135
°
14.124'N
21.567'W
04 005WPT
34
135
°
44.569'N
21.152'W
05 008WPT
34
135
°
54.124'N
21.888'W
LEG
29.9
°
12.0nm
159.9
°
6.00nm
50.5
°
29.8nm
359.9
°
3.0nm
RE-
START
STOP
RVRSE
SPEED
COORD
TYPE
Replaced by
"FOLLOW LEG" when selecting a route leg.
Log display
4. Use the cursor pad to select a waypoint or a route leg. When a route leg is selected the single arrow cursor is replaced by double arrows.
5. Press the RESTART soft key, or FOLLOW LEG soft key in case of route leg.
Note: Navigation may be restarted from the plotter display, with the
RESTART key, when a single quick point (QP<01>) is selected for navigation.
6. Press the [MENU] key to close the menu.
3. PLOTTER OPERATION
Setting speed for ETA calculation
Speed, which may be input manually or automatically, is required to calculate
ETA (Estimated Time of Arrival) to a waypoint.
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES soft key.
3. Press the LOG soft key.
4. Press the SPEED soft key.
SPEED FOR ETA
▲
¤
¡
▼
SPD 0 10.0kt
GPS AVG. SPEED
Select speed for ETA window
5. Key in speed manually in the SPD field, or use GPS speed data (if applicable) by selecting GPS AVG. SPEED.
6. Press the ENTER soft key or the [ENTER] knob to register your selection.
7. Press the [MENU] key to close the menu.
Switching waypoints
When you arrive to a waypoint on a route, you can switch to the next waypoint three ways: perpendicular to waypoint, arrival alarm circle and manual.
PERPENDICULAR: Automatically switches the TO waypoint when the boat enters the arrival alarm range or the boat passes an imaginary perpendicular line passing through the center of the destination waypoint.
ARRVL ALM CRCL: Automatically switches the TO waypoint when the boat enters the arrival alarm range. For how to set the arrival alarm, see paragraph
3.11.2 Arrival alarm.
MANUAL: MANUAL: When the boat nears a destination waypoint, the destination waypoint may be manually switched by using the RESTART soft key
(see page 3-50). This function is operative when “1 POINT” is selected as the
GOTO method (see page 3-45).
WPT 2 WPT 2
Waypoint switched at this point.
Waypoint switched at this point.
WPT 1
Perpendicular
WPT 1
Arrival Alarm Circle
How waypoints are switched in perpendicular and arrival alarm circle
3-51
3. PLOTTER OPERATION
To select waypoint switching method do the following:
1. Press the [MENU] key.
2. Press the PLOTTER SETUP soft key.
3. Use the cursor pad to select WAYPOINT SWITCHING.
4. Press the EDIT soft key to show the waypoint switching window.
5. Use the cursor pad to select appropriate waypoint switching method;
PERPENDICULAR, ARRVL ALM CRCL (default setting), or MANUAL.
6. Press the ENTER soft key or [ENTER] knob.
7. Press the [MENU] key to close the menu.
Canceling route navigation
1. Press the [MENU] key to open the menu.
2. Press the WAYPOINTS/ROUTES soft key.
3. Press the LOG soft key.
4. Press the STOP soft key.
5. Push the [ENTER] knob.
6. Press the RELEASE soft key.
7. Push the [ENTER] knob.
3-52
3. PLOTTER OPERATION
3.11 Alarms
When an alarm setting has been violated the buzzer sounds and the speaker icon appears (in red on the 1722C series). Press the [CLEAR] key to silence the alarm. You can see which alarm has been violated on the alarm menu display.
You may set up the plotter alarms on the ALARM menu, which may be displayed by pressing the [ALARM] key. For 1722C series, note that the alarm icon is red when an alarm setting is violated, and turns black when the [CLEAR] key or
CLEAR ALARM soft key is pressed. The color does not change when another alarm is violated.
AUDIO ALARM
INTERNAL BUZZ
ARRIVAL ALARM
OFF 0.010nm
ANCHOR WATCH ALARM
OFF 0.010nm
PROXIMITY ALARM
OFF
XTE ALARM
OFF 0.050nm
SPEED ALARM
OFF
TRIP ALARM
OFF 0000.0nm
ALARM1
EDIT
CLEAR
ALARM
NEXT
PAGE
NEXT
PAGE
PREV.
PAGE
BOTTOM ALARM
OFF
TEMPERATURE ALARM
OFF
ALARM 2
EDIT
PREV..
PAGE
RETURN
ALARM INFOMATION
NO ALARM
ALARM INFOMATION
NO ALARM
Page 1 Page 2
Plotter alarm menu
3.11.1 Audio alarm on/off
Audio and visual alarms are released whenever an alarm setting is violated. You can enable or disable the audio alarm as follows:
1. Press the [ALARM] key to show the alarm menu.
2. Use the cursor pad to select AUDIO ALARM.
3. Press the EDIT soft key to show the audio alarm window.
AUDIO ALARM
¤
¡
¡
INT & EXT BUZZ
INTERNAL BUZZ
OFF
Audio alarm window
4. Use the cursor pad to select INT & EXT BUZZ (Internal + External alarm),
INTERNAL BUZZ (Internal alarm) or OFF. This turns on or off the audio alarm globally for all alarms, including radar.
5. Press the ENTER soft key followed by the [ALARM] key to close the menu.
3-53
3. PLOTTER OPERATION
The arrival alarm informs you that your boat is approaching a destination waypoint. The area that defines an arrival zone is that of a circle which you approach from the outside of the circle. The alarm will be released if your boat enters the circle. When the arrival alarm is active a dashed circle (red on the
MODEL1722C series) marks the arrival alarm area.
Note: Arrival alarm and anchor watch alarm cannot be set together.
Alarm range
Own ship
: Alarm area
Destination waypoint
How the arrival alarm works
1. Press the [ALARM] key to open the alarm menu.
2. Use the cursor pad to select ARRIVAL ALARM.
3. Press the EDIT soft key to show the arrival alarm window.
ARRIVAL ALARM
▲
¡
¤
▼
ON 0.010nm
OFF
Arrival alarm window
4. Use the cursor pad to select ON.
5. Use the cursor pad and [ENTER] knob to enter alarm range: Use ◄ or ► to select digit; rotate the [ENTER] knob to set value. The available arrival alarm range is 0.001 to 9.999 miles.
6. Press the ENTER soft key or push the [ENTER] knob to register setting.
7. Press the [ALARM] key to close the menu.
3-54
3. PLOTTER OPERATION
The anchor watch alarm informs you that your boat is moving when it should be at rest. When the anchor watch is active, a dashed circle (red on the
MODEL1722C series) with an “X” at its center marks the anchor watch area.
Alarm setting
Your ship's position where you start the anchor watch alarm.
: Alarm
area
How the anchor watch alarm works
1. Press the [ALARM] key to open the alarm menu.
2. Use the cursor pad to select ANCHOR WATCH ALARM.
3. Press the EDIT soft key to open the anchor alarm window.
ANCHOR WATCH ALARM
▲
¡
¤
▼
ON 0.050nm
OFF
Anchor watch alarm window
4. Use the cursor pad to select ON.
5. Use the cursor pad and [ENTER] knob to enter alarm range: Use ◄ or ► to select digit; rotate the [ENTER] knob to set value. The available anchor watch range is 0.001 to 9.999 miles.
6. Press the ENTER soft key or push the [ENTER] knob to register setting.
7. Press the [ALARM] key to close the menu.
Note: If the arrival alarm range is changed, turn off the anchor watch alarm and then turn it on again to give priority to the anchor watch alarm.
3-55
3. PLOTTER OPERATION
3.11.4 XTE (Cross Track Error) alarm
The XTE alarm warns you when your boat is off its intended course. When the
XTE alarm is active two dashed lines (red on the MODEL1722C series) mark the
XTE alarm area.
Own ship position
Alarm setting
Destination waypoint
Intended course
: Alarm
How the XTE alarm works
1. Press the [ALARM] key to open the alarm menu.
2. Use the cursor pad to select XTE ALARM.
3. Press the EDIT soft key to open the XTE alarm window.
XTE ALARM
▲
¡
¤
▼
ON 0.050nm
OFF
XTE alarm window
4. Use the cursor pad and [ENTER] knob to enter alarm range: Use ◄ or ► to select digit; rotate the [ENTER] knob to set value. The available XTE alarm range is 0.001 to 9.999 miles.
5. Press the ENTER soft key or push the [ENTER] knob to register setting.
6. Press the [ALARM] key to close the menu.
The speed alarm warns when your boat’s speed is within, over/under or under the speed range set.
1. Press the [ALARM] key to open the alarm menu.
2. Use the cursor pad to select SPEED ALARM.
3. Press the EDIT soft key to display the speed alarm window.
SPEED ALARM
▲
¡ WITHIN
000.0 ~ 000.0 kt
¡ UNDER/OVER
000.0 ~ 000.0 kt
¤ OFF
▼
Speed alarm window
3-56
3. PLOTTER OPERATION
4. Use the cursor pad to select WITHIN, OVER/UNDER, or OFF.
5. For WITHIN and OVER/UNDER, use the cursor pad and [ENTER] knob to enter alarm range: Use ◄ or ► to select digit; rotate the [ENTER] knob to set value.
6. Press the ENTER soft key or push the [ENTER] knob to register setting.
7. Press the [ALARM] key to close the menu.
The proximity alarm alerts you when own ship nears a waypoint, which is marked with the proximity mark, by the proximity alarm radius set for that waypoint on the waypoint list. When own ship is within a waypoint’s proximity alarm radius, the alarm sounds. The proximity mark remains on the screen until the proximity alarm is turned off or the waypoint is erased. (Note that the
MODEL 1 722C series show the proximity mark and dashed circle in red.)
Radius in proportion to proximity alarm radius, which is set on waypoint list
001WPT
Proximity mark
1 . Press the [ALARM] key to open the alarm menu.
2. Use the cursor pad to select PROXIMITY ALARM.
3. Press the EDIT soft key to show the proximity alarm window.
PROXIMITY ALARM
▲
¤
¡
▼
ON
OFF
Proximity alarm window
4. Use the cursor pad to select ON or OFF.
5. Press the ENTER soft key or [ENTER] knob.
6. Press the [ALARM] key to close the menu.
3-57
3. PLOTTER OPERATION
The trip alarm informs you when you traveled a certain distance.
1. Press the [ALARM] key to open the alarm menu.
2. Use the cursor pad to select TRIP ALARM.
3. Press the EDIT soft key to show the trip alarm window.
TRIP ALARM
▲
¡
¤
▼
ON 0000.0nm
OFF
Trip alarm window
4. Select ON with the cursor.
5. Use the cursor pad and [ENTER] knob to enter alarm range: Use ◄ or ► to select digit; rotate the [ENTER] knob to set value.
6. Press the ENTER soft key or push the [ENTER] knob to register setting.
7. Press the Press the [ALARM] key to close the menu.
3-58
3. PLOTTER OPERATION
When an alarm setting has been violated the buzzer sounds and the speaker icon appears (in red on the color model). Press the [CLEAR] key to silence the alarm. You can see which alarm has been violated on the alarm menu display. In the example below the arrival alarm has been violated.
1. Press the [ALARM] key. The name of the offending alarm appears in the
ALARM INFORMATION window.
AUDIO ALARM
INT & EXT BUZZ
ARRIVAL ALARM
ON 0.010nm
ANCHOR WATCH ALARM
OFF 0.010nm
PROXIMITY ALARM
OFF
XTE ALARM
OFF 0.050nm
SPEED ALARM
OFF
TRIP ALARM
OFF 0000.0nm
ALARM1
EDIT
NEXT
INFO
CLEAR
ALARM
NEXT
PAGE
RETURN
Alarm information window
ALARM INFOMATION
ARRIVED
AT WAYPOINT.
CONTINUE
Speaker icon
Means multiple alarms have been violated.
Alarm menu)
2. Press the CLEAR ALARM soft key to acknowledge the alarm (and silence the alarm if it was not already silenced with the [CLEAR] key.) For the color model, the speaker icon changes from red to background color. The icon remains on the screen until the cause of the alarm is eliminated or the alarm is disabled.
Note: If more than one alarm has been violated the message CONTINUE appears at the bottom of the alarm information window. In this case press the NEXT INFO soft key to see which other alarms have been violated.
3. Press the [ALARM] key to close the alarm menu.
3-59
3. PLOTTER OPERATION
Alarm messages
The table below shows the plotter alarm messages and their meanings
Plotter alarm messages and their meanings
Message Meaning
ARRIVED AT XXX WAYPOINT! Arrival alarm violated.
(XXX = waypoint number)
Proximity alarm violated. ENTERED INTO AVOIDANCE
AREA!
EXCEEDED ANCHOR WATCH
LIMIT!
Anchor watch alarm violated.
EXCEEDED XTE LIMIT!
SPEED ALARM!
TEMPERATURE ALARM!
TRIP ALARM! MILEAGE
EXCEEDED
XTE alarm violated.
Speed alarm violated.
Water temperature alarm violated.
Trip alarm violated.
Trip distance is shown on the navigation data display. You can reset the trip distance to zero as follows:
1. Press the [MENU] key.
2. Press the SYSTEM CONFIGURATION and GENERAL SETUP soft keys in that order to show the GENERAL SETUP menu.
GENERAL
SETUP1
KEY BEEP
ON
LANGUAGE
ENGLISH
RANGE UNIT nm, kt
TEMPERATURE UNIT
F
DEPTH UNIT ft
TEMPERATURE SOURCE
NMEA
DEPTH SOURCE
NMEA
RESET TRIP LOG
NO
EDIT
NEXT
PAGE
RETURN
General setup menu, page 1
3. Use the cursor pad to select RESET TRIP LOG and press the EDIT soft key.
4. Use the cursor pad to select YES.
5. Press the ENTER soft key.
6. Press the [MENU] key to close the menu.
3-60
3. PLOTTER OPERATION
3.13 Entering the MOB Mark, Setting MOB as
Destination
The MOB (Man Overboard) mark functions to mark man overboard position. You can inscribe this mark from any mode, except while playing back data or conducting a self-test. Note that this function requires position data.
MOB mark
M
(MOB)
Range, bearing
Man overboad
Current position
M
O
B
162.5
°
0.49 nm
MOB Data Box
Bearing and range to MOB position
MOB concept
1. Press and hold down the [SAVE/MOB] key for about three seconds when someone falls onboard. The display shows the waypoint number being saved
(youngest empty waypoint number, 001-999) followed by the MOB confirmation window.
XXX = Waypoint number
WAYPOINT SAVED!
XXXWPT
CONTINUE PUSHING
FOR MOB!
After several seconds
MAN OVER BOARD!
GO TO MOB?
YES ... PUSH ENTER KNOB
NO ... PUSH CLEAR KEY
MOB mark messages
2. Push the [ENTER] knob to select the MOB position as the destination, or press the [CLEAR] key to only mark current ship’s position as a waypoint. If you select the MOB position as destination;
•
A full-screen radar, plotter or overlay (color model only) appears depending on the display in use.
•
The MOB mark “MOB” appears at the MOB position and a line runs between it and current position. This line shows the shortest course to the MOB position.
•
Range and bearing to the MOB position are shown in the MOB data box.
To erase an MOB mark from the plotter display, you must first erase its corresponding waypoint.
Place the cursor on the MOB mark, then press the
[CLEAR] key followed by pushing the [ENTER] knob to erase the waypoint. Then, repeat to erase the MOB mark..
3-61
With connection of the optional network sounder you can show video sounder images on the display.
4.1 Principle Operation
The video sounder determines the distance between its transducer and underwater objects such as fish, lake bottom or seabed and displays the results on screen. It does this by utilizing the fact that an ultrasonic wave transmitted through water travels at a nearly constant speed of 4800 feet (1500 meters) per second. When a sound wave strikes an underwater object such as fish or sea bottom, part of the sound wave is reflected back toward the source (transducer).
Thus by calculating the time difference between the transmission of a sound wave and the reception of the reflected sound wave, the depth to the object can be determined.
The entire process begins in the network sounder. Transmitter power is sent to the transducer as a short pulse of electrical energy. The electrical signal produced by the transmitter is converted into an ultrasonic signal by the transducer and transmitted into the water. Any returning signals from intervening objects (such as a fish school) are received by the transducer and converted into an electrical signal. The signals are then amplified in the amplifier section, and finally, displayed on screen.
The picture displayed is made up of a series of vertical scan lines, one for each transmission. Each line represents a snapshot of what has occurred beneath the boat. A series of snapshots are accumulated side by side across the screen, and the resulting contours of the bottom and fish between the bottom and surface are displayed.
100
-
-
-
-
50
-
-
-
-
0
-
-
-
-
Underwater conditions and video sounder display
4-1
4. VIDEO SOUNDER OPERATION
4.2.1 Selecting a sounder display
There are seven display modes from which to choose: dual frequency, single frequency, marker zoom, bottom zoom, bottom lock, bottom discrimination, and
A-scope
To select a display;
1. Press the [DISP] key and select a sounder display.
2. If not displayed, press the [HIDE/SHOW] key to show the sounder soft keys.
3. Press the DISPLY MODE soft key to show the display mode window.
DISPLAY MODE
¡
¤
¡
¡
¡
¡
DUAL FREQ
SINGLE FREQ
MARKER ZOOM
BOTTOM ZOOM
BOTTOM LOCK
BOTTOM DSCRM
Display mode window
4. Use the cursor pad to select a display.
5. Press the RETURN soft key to close the window.
Note: On menus which show the RETURN soft key you may use it or the
ENTER knob to register setting and close the window.
4-2
4. VIDEO SOUNDER OPERATION
4.2.2 Description of sounder displays
Single frequency display
Display mode
Variable Range Marker (white)
Minute marker
Depth scale
Time
Soft keys
Zero line
Icons
(alarm, battery, simulation)
F
50
Color bar
40
Temp. scale
(orange)
Water temp.
graph
30
S
M
Fish echo
0'30"
0
SOUNDER
SINGLE
SHIFT
52 50
Cross-hair cursor
100
AUTO/
D. BOX
FREQ
50 /200
DISPLY
MODE
150
Water temp.
display
114
50k 200
Tx frequency Bottom echo
Depth
Indications on the single frequency display
Note 1: The water temperature display requires an appropriate water temperature sensor. It can be turned on or off with TEMPERATURE
GRAPH on the SOUNDER menu.
Note 2: When using the vertically split plotter/sounder display with dual frequency or zoom display, the depth scale is not displayed. Further, a last digit on the depth may be overlapped by the line which splits screens.
Selecting transmission frequency
The single frequency display shows either the 50 kHz picture or 200 kHz picture.
To select transmission frequency, press the FREQ 50/200 soft key to select “50” or “200”.
4-3
4. VIDEO SOUNDER OPERATION
Dual-frequency display
The dual-frequency display provides both 50 kHz and 200 kHz pictures. This display is useful for comparing the same picture with two different sounding frequencies.
0.0
50k 200k
Dual-frequency display
50 kHz picture
The sounder uses ultrasonic pulses to detect bottom conditions. The lower the frequency of the pulse, the wider the detection area. Therefore, the 50 kHz frequency is useful for general detection and judging bottom condition.
200 kHz picture
The higher the frequency of the ultrasonic pulse the better the resolution.
Therefore, the 200 kHz frequency is ideal for detailed observation of fish school.
50 kHz
200 kHz
Sounding area and transmission frequency
4-4
4. VIDEO SOUNDER OPERATION
Marker-zoom display
The marker-zoom display expands a selected area of the normal sounder picture to full vertical size of the screen on the left-half window. You may specify the portion to expand by operating the VRM (Variable Range Marker), which you can shift with the [ENTER] knob. The area between the VRM and zoom marker is expanded. The length of the segment is equal to one division of the depth scale.
Fish school
80
46
-
48
50
-
-
-
42
44
-
-
Fish school
200k
0'20"
0
-
-
42.0
50
100
-
-
-
-
-
-
-
-
VRM
(White on color model)
This part is zoomed.
Zoom marker
MARKER-ZOOM
DISPLAY
NORMAL
DISPLAY
Marker-zoom display plus normal sounder display
Note: The zoom marker is turned off in the default setting. You can turn it on with
ZOOM MARKER on the SOUNDER menu.
Bottom-zoom display
The bottom-zoom display expands bottom and bottom fish echoes by the zoom range selected on the sounder range setup menu (see paragraph 5.9.3), and is useful for determining bottom hardness. A bottom displayed with a short echo tail usually means it is a soft, sandy bottom. A long echo tail means a hard bottom.
Note: The zoom marker is turned off in the default setting. You can turn it on with
ZOOM MARKER on the SOUNDER menu.
Bottom
80
60
50
40
-
-
-
-
-
-
-
-
-
-
20.0
200k
50
0
-
-
-
-
-
-
-
-
100 -
-
Zoom marker
BOTTOM-ZOOM
DISPLAY
NORMAL DISPLAY
Bottom-zoom display plus normal sounder display
4-5
4. VIDEO SOUNDER OPERATION
Bottom-lock display
The bottom-lock display provides a compressed normal picture on the right half of the screen and a 3 or 6 meter (10 or 20 feet) wide layer in contact with the bottom is expanded onto the left half of the screen. This mode is useful for discriminating bottom fish from the bottom echo. You may select the bottom lock range from the SOUNDER RANGE SETUP menu. For details, see paragraph
5.9.3.
Fish school
80
20
-
-
15
-
60
-
10
10
-
5
This part is zoomed.
200k
50
0
-
-
-
-
-
-
-
-
100 -
-
Zoom marker
BOTTOM-LOCK
DISPLAY
NORMAL DISPLAY
Bottom-lock display plus normal sounder display
Bottom discrimination display
The bottom discrimination mode displays the bottom echo to help you determine bottom hardness. A bottom displayed with a short echo tail usually means it is a soft, sandy bottom. A long echo tail means a hard bottom.
Bottom trail
Long tail=Hard bottom
Short tail=Soft bottom
80
2
4
-
-
-
-
-
-
-
-
0
-
-
-
-
50
-
20.0
200k
50
100 -
-
0
-
-
-
-
BOTTOM
DISCRIMINATION
DISPLAY
NORMAL DISPLAY
Bottom discrimination display
Zoom marker
4-6
4. VIDEO SOUNDER OPERATION
A-scope display (display only)
The A-scope display, available in all modes, shows echoes at each transmission with amplitudes and tone proportional to their intensities, on the right 1/3 of the screen. It is useful for estimating fish species and seabed composition. To turn on the A-scope display, press the DISPLAY MODE soft key, select display mode desired, then press the A-SCPE soft key to turn the A-scope display on or off as appropriate. For the mode except SINGLE MODE the screen must be split horizontally to show the A-scope presentation.
84
200k
50
100
0
-
-
-
-
-
-
-
-
-
-
A-scope Display
No response
Weak echo (fish)
Strong echo (bottom)
SINGLE FREQ DISPLAY A-SCOPE
DISPLAY
A-scope display
4.2.3 Selecting screen split method in combination displays
On combination sounder displays you can split the screen vertically or horizontally, using the SPLIT soft key as below.
0.0
0.0
SPLIT
/
SPLIT
/
200k
50k 200k 50k
How to use the SPLIT soft key (example: dual frequency display)
4-7
4. VIDEO SOUNDER OPERATION
4.3 Automatic Sounder Operation
Automatic sounder operation is useful when you are preoccupied with other tasks and do not have the time to adjust the display.
4.3.1 How the automatic sounder works
The automatic sounder function automatically selects the proper gain, range scale and clutter suppression level according to depth. It works as follows:
• Range changes automatically to locate the bottom on the lower half of screen.
The range jumps to one step shallower range when bottom echoes reach a half way point of the full scale from top and to one step deeper range when they come to the lower edge of the scale.
• The gain is automatically adjusted to display the bottom echo in reddish brown
(default color arrangement).
• Clutter, which suppresses low level noise, is automatically adjusted.
4.3.2 Types of automatic sounder modes
Two types of automatic sounder modes are available: CRUISING and FISHING.
CRUISING is for tracking the bottom, and FISHING is for searching fish schools.
CRUISING uses a higher clutter rejection setting than FISHING therefore it is not recommended for fish detection - weak fish echoes may be erased by the clutter suppression circuit.
4.3.3 How to enable automatic sounder operation
1. If not displayed, press the [HIDE/SHOW] key to show the sounder soft keys.
2. Press the AUTO/D. BOX soft key.
AUTO MODE
▲
¤
¡
¡
▼
CRUISING
FISHING
OFF (MANUAL)
Mode/frequency window
3. Use the cursor pad to select CRUISING or FISHING as appropriate.
4. Press the RETURN soft key to close the window.
4-8
4. VIDEO SOUNDER OPERATION
4.4 Manual Sounder Operation
Manual operation is useful for observing fish schools and bottom using fixed gain setting.
The gain, range and range shifting functions used together give you the means to select the depth you can see on screen. The basic range can be thought of as providing a “window” into the water column and range shifting as moving the
“window” to the desired depth.
4.4.1 Selecting the manual mode
1. If not displayed, press the [HIDE/SHOW] key to show the sounder soft keys.
2. Press the AUTO/D. BOX soft key to show the mode/frequency window.
3. Select OFF (MANUAL).
4. Press the RETURN soft key.
Press the [RANGE +] or [RANGE -] key to select a range. The default ranges in feet, meters, fathoms and passi/braza are as below. Note that range cannot be changed in the automatic sounder mode.
Default sounder ranges
Range 1 Range 2 Range 3 Range 4 Range 5 Range 6 Range 7 Range 8
15 ft 30 ft 60 ft 120 ft 200 ft 400 ft 1000 ft 4000 ft
5 m 10 m 20 m
3 fa 5 fa 10 fa
3 PB 5 PB 10 PB
4.4.3 Adjusting the gain
40 m
20 fa
30 PB
80 m
40 fa
50 PB
150 m
80 fa
100 PB
300 m 1200m
150 fa
200 PB
650 fa
700 PB
Normally, set the gain to the point where excessive noise does not appear on screen. Use a higher gain setting for greater depths and a lower setting for shallow waters.
Gain too high Gain proper Gain too low
Examples of proper and improper gain
4-9
4. VIDEO SOUNDER OPERATION
Press the [GAIN] key to show the gain window, and rotate the [ENTER] knob to set the gain. Current level is shown on the bar. Press the RETURN key to finish.
The setting range is 0-100 (%).
GAIN 200kHz
▲
HIGH
27
LOW
▼
Gain window
Note 1: On the dual-frequency display, the gain can be independently set for 50 kHz and 200 kHz. Use the FREQ 50/200 soft key to select the frequency for which to adjust gain.
Note 2: Gain cannot be adjusted in the automatic sounder mode. The message
“SOUNDER GAIN CANNOT BE CHANGED IN AUTO MODE” is displayed when you attempt to do so.
The basic range may be shifted up or down as desired by pressing the SHIFT soft key followed by adjusting the [ENTER] knob or ▲ or ▼ on the cursor pad.
Press the RETURN soft key to finish.
Shift
Shift concept
4-10
4. VIDEO SOUNDER OPERATION
4.5 Measuring Depth, Time
The VRM functions to measure the depth, and the time cursor measures time.
1. Rotate the [ENTER] knob to shift the VRM; counterclockwise the shift it downward, clockwise to shift it upward. You may also use the cursor pad to shift the VRM, in which case use ▲ or ▼ .
2. Use ◄ or ► on the cursor pad to shift the cross-hair cursor to measure time.
Time to cursor intersection
(Max. 99'59")
Depth to VRM
84
50k
0'33"
28.8
Cross-hair cursor
50
-
-
-
-
-
-
-
-
0
100
-
-
VRM
How to use the VRM, time cursor
Note: If, when the range setting is over 1000 ft (m, fa, p/b), the VRM indication and depth scale may overlap one another, shift the cross-hair cursor slightly to show them completely. Further, when the display is shifted, the depth scale may obscure the time indication.
4-11
4. VIDEO SOUNDER OPERATION
Interference from other acoustic equipment operating nearby or other electronic equipment on your boat may show itself on the display as shown below.
Interference from Electrical inteference other sounder
Types of interference
To reduce interference, do the following:
1. Press the [MENU] key.
2. Press the SOUNDER MENU soft key.
3. Select NOISE LIMITER and press the EDIT soft key to show the noise limiter window.
NOISE LIMITER
▲
¤
¡
¡
¡
▼
OFF
LOW
MEDIUM
HIGH
Noise limiter window
4. Use the cursor pad to select degree of suppression desired (LOW, MEDIUM,
HIGH) or turn the noise limiter off.
5. Press the RETURN soft key followed by the [MENU] key to close the menu.
Turn the noise limiter function off when no interference exists, otherwise weak echoes may be missed.
4-12
4. VIDEO SOUNDER OPERATION
4.7 Reducing Low Level Noise
Dots (light-blue on the color model) may appear over most of the screen. This is mainly due to sediment in the water or noise. This noise can be suppressed by adjusting CLUTTER on the SOIUNDER menu.
Appearance of clutter
When the sounder mode is Auto, the clutter suppression setting is fixed at AUTO.
To reduce low level noise in manual sounder operation do the following:
1. Press the [MENU] key.
2. Press the SOUNDER MENU soft key.
3. Select CLUTTER and press the EDIT soft key to show the clutter window.
CLUTTER
▲
00
▼
Clutter window
4. Use the cursor pad to select clutter rejection level desired; 0 (OFF) through
16, default setting, 9. The higher the number the higher the degree of suppression. Note that the clutter suppressor may erase weak echoes.
Therefore, turn off the clutter when its use is not required.
5. Press the RETURN soft key followed by the [MENU] key to close the menu.
Note: Unlike the signal level feature, clutter does not erase echoes. However, if you do not wish to change the relation between weak and strong echoes, use signal level instead.
4-13
4. VIDEO SOUNDER OPERATION
Sediment in the water or reflections from plankton may be painted on the display in green or light blue (color display) or “spots” on the background (monochrome display). These weak echoes may be erased as below.
Weak echoes
Appearance of weak echoes
1. Press the [MENU] key.
2. Press the SOUNDER MENU soft key.
3. Select SIGNAL LEVEL, and press the EDIT soft key to show the signal level window.
SIGNAL LEVEL
▲
¡
¡
¡
¤
¡
¡
¡
▼
OFF
SL1
SL2
SL3
SL4
SL5
SL6
SIGNAL LEVEL
▲
¤
¡
¡
¡
▼
OFF
SL1
SL2
SL3
SIGNAL LEVEL
▲
¤
¡
¡
▼
OFF
SL1
SL2
16-color display 8-color display Monochrome display
Signal level window
4. Use the cursor pad to select level of erasure or OFF as appropriate. The higher the number the stronger the echo that will be erased.
5. Press the RETURN soft key followed by the [MENU] key to close the menu.
Note: Unlike “clutter,” signal level erases echoes. Therefore if you do not wish to erase echoes use clutter instead.
4-14
4. VIDEO SOUNDER OPERATION
4.9 White Marker (MODEL1722C series)
The white marker functions to display a particular echo color in white. For example, you may want to display the bottom echo in white to discriminate fish echoes near the bottom. Note that the bottom must be displayed in reddish-brown (color in default hue setting) for the white marker to function.
1. Press the [MENU] key.
2. Press the SOUNDER MENU soft key.
3. Select WHITE MARKER, and press the EDIT soft key to open the white marker window.
WHITE MARKER
▲
0
▼
White marker window
4. Use the cursor pad to select color to display in white. As you use the cursor pad, the number (corresponds to echo number) in the marker window changes, the white marker on the echo strength bar shifts and selected echo color is displayed in white.
←
White marker shows color currently displayed in white.
Echo strength bar (16 color) when white marker function is active
5. Press the RETURN soft key followed by the [MENU] key to close the menu.
To turn the white marker function off, display “OFF” in the white marker window.
4-15
4. VIDEO SOUNDER OPERATION
The picture advance speed determines how quickly the vertical scan lines run across the screen. When selecting a picture advance speed, keep in mind that a fast advance speed will expand the size of the fish school horizontally on the screen and a slow advance speed will contract it.
The advancement speed may be set independent of ship’s speed or synchronized with ship’s speed.
4.10.1 Advancement independent of ship’s speed
1. Press the [MENU] key.
2. Press the SOUNDER MENU soft key.
3. Select PICTURE ADVANCE, and press the EDIT soft key to open the picture advance window.
PICTURE ADVANCE
▲
¡
¡
¡
¤
¡
¡
¡
▼
2/1
1/1
1/2
1/4
1/8
1/16
STOP
Picture advance window
The fractions in the window denote the number of scan lines produced per transmission. For example, 1/8 means one scan line is produced every eight transmissions. STOP freezes the display and it is convenient for observing an echo.
4. Use the cursor pad to select speed desired.
5. Press the RETURN soft key followed by the [MENU] key to close the menu.
Note: Advancement of the sounder picture may be temporarily interrupted while the plotter display is shifted or its display range is changed when using the plotter/sounder combination display.
4-16
4. VIDEO SOUNDER OPERATION
4.10.2 Advancement synchronized with ship’s speed
With speed data provided by a speed measuring device, picture advance speed may be automatically synchronized with ship’s speed. As shown in the figure below the horizontal scale of the display is not influenced with the speed dependent picture advance mode active, thus it permits judgement of fish school size and abundance at any speed. With the advancement synchronized with ship’s speed the picture advance speed setting (on the previous page) is ignored.
Fish school shrinks as speed is increased; expanded as speed is decreased.
Same size fish schools
Speed
FULL
SPEED
HALF
SPEED
Actual Movement
Normal Mode
Fish schools are shown same size regardless of ship’s speed.
Speed-Dependent Picture Advance Mode
How the speed-dependent picture advance mode works
Activating/deactivating the speed-dependent picture advance mode
1. Press the [MENU] key followed by the SOUNDER MENU soft key.
2. Select SPD SENSING PIC ADV.
3. Press the EDIT soft key to open the setting window.
4. Use the cursor pad to select ON or OFF (default setting) as appropriate.
5. Press the ENTER soft key.
6. Press the [MENU] key to close the menu.
Note: Use the same speed data sentence (STG or STW) throughout the network for smooth advancement of the sounder picture.
4-17
4. VIDEO SOUNDER OPERATION
4.11 Display Colors (MODEL1722C series)
You can select the number of colors and background color to display as follows:
1. Press the [MENU] key.
2. Press the SOUNDER MENU soft key.
3. Select HUE, and then press the EDIT soft key to show the hue window.
HUE
▲
1
▼
Hue window
4. Use the cursor pad to select hue number, referring to the table below. (You can see the result of your selection on the display.)
Hue no. and background and echo colors
Hue No.
3
4
9
Echo Color
16 color
8 color
Background Color
Blue
Blue
Dark blue
Dark blue
White
White
Black
Black
Monochrome, eight intensities
5. Press the RETURN soft key followed by the [MENU] key to close the menu.
4-18
4. VIDEO SOUNDER OPERATION
4.12 Alarms
The sounder section has five conditions which generate visual and aural alarms: bottom alarm, fish alarm (bottom lock), fish alarm (normal), water temperature alarm (temperature sensor required), and speed alarm. For 1722C series, note that the alarm icon is red when an alarm setting is violated, and changes to background color when the [CLEAR] key or CLEAR ALARM soft key is pressed.
The color does not change when another alarm is violated.
You may set up the sounder alarms on the ALARM menu, which may be displayed by pressing the [ALARM] key.
SOUNDER
ALARM
AUDIO ALARM
INTERNAL BUZZ
BOTTOM ALARM
OFF
TEMPERATURE ALARM
OFF
FISH ALARM
OFF
FISH ALARM (B/L)
OFF
EDIT
CLEAR
ALARM
RETURN
ALARM INFOMATION
NO ALARM
Sounder alarm menu
4.12.1 Audio alarm on/off
The audio alarm sounds whenever an alarm setting is violated. You can enable or disable the audio alarm as follows:
1. Press the [ALARM] key to show the ALARM menu.
2. Use the cursor pad to select AUDIO ALARM.
3. Press the EDIT soft key to show the audio alarm window.
AUDIO ALARM
¡
¤
¡
INT & EXT BUZZ
INTERNAL BUZZ
OFF
Audio alarm window
4. Use the cursor pad to select INT & EXT BUZZ (Internal + External alarm),
INTERNAL BUZZ (Internal alarm) or OFF. This turns on or off the audio alarm for all modes globally, including radar.
5. Press the [ALARM] key to finish.
4-19
4. VIDEO SOUNDER OPERATION
The bottom alarm sounds when the bottom echo is within the alarm range set.
To activate the bottom alarm the depth must be displayed. Note that the bottom alarm is turned on or off reciprocally with the bottom alarm on the plotter alarm menu.
1. Press the [ALARM] key to show the ALARM menu.
2. Use the cursor pad to select BOTTOM ALARM.
3. Press the EDIT soft key to show the bottom alarm window.
BOTTOM ALARM
▲
¡ ON
0000.0-0000.0 ft
¤
▼
OFF
Bottom alarm window
4. Use the cursor pad to select ON or OFF as appropriate. For ON, enter alarm range with the cursor pad and [ENTER] knob: Use ◄ or ► to select digit; rotate the [ENTER] knob to set value.
5. Press the ENTER soft key or push the [ENTER] knob to register setting.
6. Press the [ALARM] key to finish.
The fish alarm sounds when a fish echo is within the preset alarm range. Note that the sensitivity of the fish alarm can be set on the SOUNDER SYSTEM
SETUP menu.
1. Press the [ALARM] key to show the ALARM menu.
2. Use the cursor pad to select FISH ALARM.
3. Press the EDIT soft key to show the fish alarm window.
FISH ALARM
▲
¡ ON
0000.0-0000.0 ft
¤
▼
OFF
Fish alarm window
4. Use the cursor pad to select ON or OFF as appropriate. For ON, use the cursor pad and [ENTER] knob to enter alarm range: Use ◄ or ► to select digit; rotate the [ENTER] knob to set value.
5. Press the ENTER soft key or push the [ENTER] knob to register setting.
6. Press the [ALARM] key to finish.
4-20
4. VIDEO SOUNDER OPERATION
4.12.4 Fish alarm (B/L)
The bottom-lock fish alarm sounds when a fish echo is within a predetermined distance from the bottom. Note that the sensitivity of the fish alarm can be set on the SOUNDER SYSTEM SETUP menu.
1. Press the [ALARM] key to show the ALARM menu.
2. Use the cursor pad to select FISH ALARM (B/L).
3. Press the EDIT soft key to show the fish alarm (B/L) window.
FISH ALARM (B/L)
▲
¡ ON
0000.0-0000.0 ft
¤ OFF
▼
Fish alarm (B/L) window
4. Use the cursor pad to select ON or OFF as appropriate. For ON, use the cursor pad and [ENTER] knob to enter alarm range: Use ◄ or ► to select digit; rotate the [ENTER] knob to set value.
5. Press the ENTER soft key or push the [ENTER] knob to register setting.
6. Press the [ALARM] key to finish.
4-21
4. VIDEO SOUNDER OPERATION
4.12.5 Water temperature alarm
There are two types of water temperature alarms: WITHIN RANGE and OUT OF
RANGE. The WITHIN RANGE alarm sounds when the water temperature is within the range set, the OUT OF RANGE alarm sounds when the water temperature is higher or lower than the range set. This alarm requires water temperature data.
Note that the water temperature alarm is turned on or off reciprocally with the water temperature alarm on the plotter alarm menu.
1. Press the [ALARM] key to show the ALARM menu.
2. Use the cursor pad to select TEMPERATURE ALARM.
3. Press the EDIT soft key to show the temperature alarm window.
TEMPERATURE ALARM
▲
¡ WITHIN RANGE
-000.0 - +000.0
°
F
¡ OUT OF RANGE
-000.0 - +000.0
°
F
¤
▼
OFF
Water temperature alarm window
4. Use the cursor pad to select WITHIN RANGE, OUT OF RANGE or OFF as appropriate. For WITHIN RANGE and OUT OF RANGE, use the cursor pad and [ENTER] knob to enter alarm range: Use ◄ or ► to select digit; rotate the [ENTER] knob to set value.
5. Press the ENTER soft key or push the [ENTER] knob to register setting.
6. Press the [ALARM] key to finish.
4-22
4. VIDEO SOUNDER OPERATION
4.12.6 When an alarm setting is violated...
When an alarm setting has been violated the buzzer sounds and the speaker icon appears (in red on the color model). Press the [CLEAR] key to silence the alarm. You can see which alarm has been violated on the alarm menu display. In the example below the arrival alarm has been violated.
To see which alarm(s) has been violated;
1. Press the [ALARM] key. The offending alarm is shown in the ALARM
INFORMATION window.
SOUNDER
ALARM
AUDIO ALARM
INTERNAL BUZZ
BOTTOM ALARM
OFF
TEMPERATURE ALARM
OFF
EDIT
FISH ALARM
0164.0-0328.1ft
FISH ALARM (B/L)
OFF
CLEAR
ALARM
RETURN
Alarm information window
ALARM INFOMATION
FISH ALARM!
Speaker icon
Sounder alarm menu
2. Press the CLEAR ALARM soft key to acknowledge the alarm (and silence the buzzer if it was not already silenced with the [CLEAR] key.) For the color model, the speaker icon changes from red to background color on the color model and changes to normal video on the monochrome model. The speaker icon remains on the screen until the reason for the alarm is eliminated.
Note: If more than one alarm has been violated the message CONTINUE appears at the bottom of the alarm information window. In this case press the NEXT INFO soft key to see which other alarms have been violated.
3. Press the [ALARM] key to finish.
4-23
4. VIDEO SOUNDER OPERATION
Alarm messages
The table below shows the sounder alarm messages and their meanings
Sounder alarm messages and their meanings
Message Meaning
DEPTH ALARM! Bottom alarm violated.
FISH ALARM! Fish alarm violated.
TEMPERATURE ALARM! Water temperature alarm violated.
4.13 Water Temperature Graph
The water temperature graph (appropriate sensor required) plots water temperature on the sounder display. (See the figure on page 4-3.) It can be turned on or off as below.
1. Press the [MENU] key to open the menu.
2. Press the SOUNDER MENU soft key.
3. Select TEMPERATURE GRAPH and press the EDIT soft key.
4. Select OFF (default setting) or ON as appropriate.
5. Press the ENTER soft key.
6. Press the [MENU] key to close the menu.
4-24
4. VIDEO SOUNDER OPERATION
4.14 Interpreting the Sounder Display
The zero line (sometimes referred to as the transmission line) represents the transducer’s position, and moves off the screen when a deep phased range is used.
Zero line
Zero line
Shift
Echoes from the bottom are normally the strongest and are displayed in reddish-brown (color model) or darkest tone (monochrome model) but the color
(tone on the monochrome model) and width will vary with bottom composition, water depth, frequency, sensitivity, etc.
In a comparatively shallow depth, a high gain setting will cause a second or sometimes a third or a fourth echo to be displayed at the same interval between them below the first echo trace. This is because the echo travels between the bottom and the surface twice or more in shallow depths.
The color (tone for monochrome model) of the bottom echo can be used to help determine the density of the bottom materials (soft or hard). The harder the bottom, the wider the trace. If the gain is set to show only a single bottom echo on mud, a rocky bottom will show a second or third bottom return. The range should be chosen so the first and second bottom echoes are displayed when bottom hardness is being determined.
Intensity difference in water depth
Rock base
Mud and sand
Second bottom echo
Bottom echoes
4-25

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Compass display
- Highway display
- Nav data display
- Waypoint entry and editing
- Track plotting
- Marks and lines
- Chart card support
- Presentation modes
- Proximity alarms