Karma Ergo Lite KM-2501 Manual Wheelchair Owner's Manual

Karma Ergo Lite KM-2501 Manual Wheelchair Owner's Manual

Below you will find brief information for Manual Wheelchair Ergo Lite KM-2501. This manual will help you learn about how to set up, operate, and maintain your new Ergo Lite KM-2501. It is a transit wheelchair suitable for users up to 220.5 lbs. Its durable aluminum alloy frame is equipped with tough accessories and features pneumatic tires for traction and comfort. It is compatible with optional accessories, such as anti-tippers, a backrest bag, and a folding drink holder.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Manual Wheelchair Ergo Lite KM-2501 Owner's Manual | Manualzz
Ergo Lite
(KM-2501)
GENERAL WARNING
DO maintain your chair well, in particular check the tire pressure since this
affects the efficiency of the brakes.
DO make sure both brakes are applied before getting in or out of the chair.
DO make sure both brakes are applied when the chair is not being pushed or
used.
DO take care when climbing curb or turning on slopes.
DO avoid steep or uneven surfaces that may cause the chair to tip over.
DO avoid soft surfaces because the casters may become bogged down.
DO travel smoothly in all conditions.
DO look well ahead to anticipate hazards such as furniture, doors, potholes,
slopes, curbs, doorways etc.
DO make sure that both feet are safely on the footrests and that clothing is
safely tucked out of the way so that it cannot get caught in the wheels.
DO take care when travelling up or down or across inclines.
DO keep both hands on the push handles to control the chair, if you are the
attendant.
DO pay attention to keep the chair’s balance.
DO check the frame and components regularly and refer to this user guide
during and after the warranty period.
DO tie-up the upholstery or replace which with a new one when it becomes
loose.
DO equip with anti-tippers to avoid falling backwards.
DO equip with a seat belt designed for disabled people.
DO equip with "heel loops" for disabled people.
DO clean both hands after oiling the wheelchair.
DO keep far away from flame.
DO NOT overload the chair under any circumstances.
DO NOT hang anything heavy on the back of the chair that could cause the
chair to become unstable, particularly when negotiating inclines.
DO NOT allow more than one user at a time.
DO NOT use with an unconscious patient.
DO NOT use other transport to pull the wheelchair.
DO NOT do "wheelies", since you my fall or tip over backwards and suffer a
severe injury.
DO NOT sit in the wheelchair within a moving vehicle unless it has been
affixed the labels of hook mark.
DO NOT go too fast or turn too quickly.
DO NOT travel across a slope (in any direction) greater than 7 degrees.
DO NOT stand on the footplates when getting in or out of the chair.
DO NOT go down steps forward, whether solo or with an attendant.
DO NOT attempt to lift the wheelchair by any removable (detachable) parts.
Lifting by means of any removable (detachable) parts of the wheelchair may
result in injury to the user and/or assistant or damage to the wheelchair.
DO NOT use the wheelchair when the back is folded. This alters the centre of
gravity and may cause the wheelchair to tip backwards. The back should only
be folded for storage or transport of the wheelchair.
DO NOT hang anything on the back joint that could cause the backrest
folding suddenly and may cause injury.
YOU AND YOUR KARMA SERVICE PROVIDER
No tools are required for assembly. Your wheelchair should be set up by
your authorized Karma dealer. Your authorized Karma dealer is also your
service provider. Unauthorized repairs, upgrades and add-ons will negate
your warranty and may lead to injury. Any adjustments to the rear wheel
position should be carried out by your authorized Karma service provider.
Your Karma service provider has the necessary service/maintenance manual
i
for your wheelchair.
If you have any defective parts or lose any parts, please contact your dealer
for repair and/or replacement. Please only use parts authorized by Karma.
Use of parts that are not authorized by Karma will negate your warranty.
Customers should go to their dealership for all service needs to guarantee
their warranty is not nullified. Always go to an authorized service provider.
Unauthorized repairs will nullify your warranty. Procedures other than those
described in this manual must be performed by a qualified technician. They
also have the service manual with a complete list of maintenance required to
keep your Karma wheelchair in top performance. Check the warranty
section of this manual to find out what Karma guarantees and what
maintenance and parts you will have to pay for.
Karma does not have an official list of service providers at this time. Please
contact your dealer for service. If you cannot contact your dealer, please
contact another authorized Karma dealer for service. If this is not possible
please contact us and we will arrange for a service repair. Please note that
there will be a charge for collection and delivery of your wheelchair.
CE MARKING
This wheelchair complies with the requirements of the Medical Devices Directive
93/42/EEC.
CAUTION:
Before purchasing and using a Karma wheelchair, please consult a qualified
professional to ensure that you choose a suitable product and receive training in
how to use it. It may also be necessary to fit additional equipment to your
wheelchair or change your wheelchairs set up. Please consult your service
provider.
ii
TABLE OF CONTENTS
1. PREFACE ................................................................................................................. 2
2. SAFETY .................................................................................................................... 3
3. INTENDED USE & PARTS ....................................................................................... 7
4. OPERATION ............................................................................................................. 9
4.4.2 METHOD OF RESTRAINT ................................................................................ 17
6. OPTIONS AND ACCESSARIES ............................................................................. 22
7. TROUBLESHOOTING ............................................................................................ 23
8. SPECIFICATIONS .................................................................................................. 23
9. CLEANING & RECYCLING .................................................................................... 24
1
1. PREFACE
Please carefully read this owner's manual before using the wheelchair. Improper use
of the wheelchair could result in harm or injury. Therefore, for safe and enjoyable
use of the wheelchair, please read this owner's manual.
This owner's manual includes operation instructions for the aspects of the
wheelchair, unfolding/folding instructions and instructions on how to deal with
possible accidents.
This owner's manual is written for Karma wheelchair: Ergo Lite (KM-2501).
The symbols used in this manual are explained below. Pay special attention to
the parts marked with these symbols.
WARNING:
Improper use could lead to serious injury or death.
CAUTION:
Improper use could lead to serious injury and/or damage
to your wheelchair.
SUGGESTION:
Follow these instructions to keep the wheelchair in good
condition.
This manual includes the repair and maintenance chart as well as the warranty.
If someone else uses the wheelchair, make sure that you give him or her this
owner's manual for his or her reference.
As designs change, some illustrations and pictures in this manual may not
correspond to the wheelchair that you purchased. We reserve the right to make
design modifications without further notice.
2
2. SAFETY
2.1 Doorways
The safest way to operate the chair is on level floors that are free of obstacles.
Whenever possible use a ramp to enter or exit a facility. Keeping your hands on
the push rims will allow you to maintain maximum balance. Do not try to force
yourself over an obstruction by propulsion and never use the sides of a doorway to
pull yourself through a passageway.
2.2 Leaning
Do not lean over the side of your wheelchair since such an action may cause your to
lose balance and fall. (See Figure 2.3)
2.3 Navigating Inclines
Never turn on a hill due to the danger of tipping.
When assisting, go straight up a slope. If you need to go down, walk
backwards until user is on level ground. (See Figures 2.4 and 2.5)
Avoid stopping on an incline; it can potentially cause you to lose control of the
chair.
Do not use the brakes to slow down or stop the wheelchair; this could cause it to
seize up or pull to on side, causing you to lose control of the wheelchair.
Whenever possible, navigate inclines with an attendant.
Operating limits: do not attempt to go or down slopes greater than 5 degree
without assistance.
2.4 Curbs
Whenever possible get help from an assistant/attendant (if you have assistance
make sure that your chair is equipped with push handles).
Avoid hard impacts when descending a Curb. A hard impact could adversely
affect the chair.
Never try to scale or descend Curbs that exceed a normal height (30-50mm).
Always be careful when climbing Curbs and never move up or down a Curb in
reverse without an assistant.
2.5 Stairs
Always use two or more assistants. Tilt the wheelchair to its point of equilibrium.
One assistant (at the back) holds the wheelchair up against the first step,
gripping the handles firmly to lift. The second assistant, holding firmly a fixed
part of the front frame, lifts the wheelchair above the stairs and holds it while the
first attendant places one foot on the following step and repeat the operation.
(See Figure2.1)
Never go down steps forwards.
Never use an escalator for transport, use an elevator.
3
Figure 2.1
Figure 2.2
2.6 Streets
Always use extreme caution when crossing streets. Reflective tape on the chair
and/or your clothing will make you more visible to drivers.
Avoid potholes and rough terrain that might cause the casters to become stuck.
(See Figure 2.6)
2.7 General
Always make sure BOTH brakes are applied before getting in or out of the chair.
Never stand on the footplates when getting in or out of the chair.
Never carry more than one passenger. Karma wheelchairs are designed for
one user.
Please make sure your clothing does not get caught in the rear wheels.
2.8 Upholstery
When cleaning the upholstery, use warm water and a mild soap.
Upholstery cleaner/foam can also be used, but avoid other cleaning solvents.
2.9 Anti-tippers
Please purchase anti-tippers and always use them to avoid personal injury. The
distance between anti-tipper and wheels is more than 5cm; the height to floor
doesn’t be over 5cm. (See Figure 2.2)
2.10 Maximum User Weight Limit
Refer to "Max. User Weight" in section 8. SPECIFICATIONS. Loads exceeding
maximum capacity can damage your wheelchair and cause malfunctions yielding a
safety hazard. The warranty does not cover damage caused by improper
operation of the wheelchair.
2.11 Avoid General Misuse:
Please note any vehicle can cause injury if used incorrectly. This user guide
contains a number of cautions. Please follow these guidelines to increase your
safety. Please be aware that careless use endangers your own safety as well as
that of others. ALWAYS follow the Highway Code when outdoors and the
guidelines written in this manual. Your wheelchair will give years of safe use if
used sensibly and carefully.
Do not let children stand or play on the wheelchair. (See Figure 2.7)
4
Figure 2.3
Figure 2.4
Figure 2.6
Figure 2.7
Figure 2.5
5
2.12 Labeling
Please carefully read all the labeling on the wheelchair before using it.
not remove them and protect them for future reference.
6
Please do
3. INTENDED USE & PARTS
3.1 Intended Use
The Ergo Lite (KM-2501) is a transit wheelchair. That is, it can be propelled by an
attendant (transit) only.
These wheelchairs are suitable for users up to 220.5 lbs in weight. Attendant
brakes are provided for both rear wheels.
It has pneumatic tires for traction and comfort. It also has an extremely durable
aluminum alloy frame with tough accessories and does not suffer in dramatic
extremes of temperature (neither user nor attendant need touch metal parts in
normal use).
The casters have PU tires for greater durability; pneumatic casters are available
on request.
When prescribing wheelchairs for use by full or partial amputees (above or below
knee, single or double) or other conditions that affects the users natural centre of
gravity, we suggest contacting your therapist or dealer as well as attaching
anti-tippers.
7
3.2 Parts Description Ergo Lite (KM-2501)
1. Push Handle
2. Attendant brake
3. Back Joint
4. Rear Wheel
5. Anti-tippers(Option)
6. Cross Brace (Cross Bar)
7. Caster
8. Backrest Upholstery
9. Armrest
10.Side Panel
11.Seat Upholstery
12.Calf Strap
13.Footplate
8
4. OPERATION
4.1 Preparing For Use
4.1.1 Unfolding
Holding the armrests, pull outwards. (See Figure 4.1)
Pointing your fingers inward with the palm of your hand on the frame, push down
until the seat is fully lowered. Make sure the frame is firmly seated in its holder.
(See Figure 4.2)
Flip the footplates down. (See Figure 4.3)
Ready for action! (See Figure 4.4)
Alternatively, you can stand at the side of the chair and complete step 1 by pulling
the nearest armrest towards you and pushing the other one away.
(Figure 4.1)
(Figure 4.2)
(Figure 4.3)
(Figure 4.4)
CAUTION:
When completing step 2 never put your fingers around
the sides or under the seat as they can be trapped
between the seat and the frame. (See Figure 4.5)
(Figure 4.5)
CAUTION:
Before use please attach the back upholstery to
seat .(see Figure 4.6)
(Figure 4.6)
4.1.2 Folding
Swing up the footplates. (See Figure 4.7)
Pull up on the seat upholstery by holding it in the centre of its front and back
9
edge. (See Figure 4.8)
Press the two release levers on the backrest frame (push handle tubes) to fold
the backrest down for compact storage and easy transport. (See Figure 4.9)
Folding is now completed. (See Figure 4.10) (Travel bag is optional)
(Figure 4.7)
(Figure 4.8)
(Figure 4.9)
(Figure 4.10)
CAUTION:
Be careful not to get your fingers caught when folding the wheelchair.
4.1.3 Adjustments
4.1.3.1 Rear wheel
Your wheelchair may be supplied with quick-release wheels. If so, please follow
the instructions below.
4.1.3.1.1 Rear Wheel Removal
Support the weight of the chair with one hand by holding the push handle.
Depress the hub cover and hold down the quick-release mechanism.
Remove the wheel. (See Figure 4.11)
4.1.3.1.2 Rear Wheel Attachment
Pick up the wheel: Hold the centre of the rear wheel by grasping two adjacent
spokes with four fingers of one hand, use the thumb to depress the quick-release.
Take the quick-release axle and depress the button in its centre. This retracts
the bearings at the opposite end of the axle. This will allow you to push the axle
through the centre of the hub of the wheel. Your wheels are now ready to be
assembled to the frame of your wheelchair.
First ensure that the brake is in the OFF position. Take up the assembled wheel
and axle and depress the button in the centre of the axle, as above. This
retracts the ball bearings that will allow you to push the axle into the wheel
bracket that is located on the lower rear frame of the wheelchair. When you
remove your thumb from the button on the axle, the ball bearings should be
visible protruding from the axle at the back of the wheel bracket. This will secure
the wheel safely in the frame. (See Figure 4.12)
CAUTION:
You must make sure that the axle is fully located in the wheelchair bracket and
that the ball bearings are fully open and have positively attached the wheel in the
frame.
10
Figure 4.11
Figure 4.12
4.1.3.1.3 Important Do’s and Don’ts
Do: Keep axles clean and lubricated with light oil or maintenance spray.
Do: Maintain correct tire pressure if using pneumatic tires.
Do not: Try to remove the wheels while the wheelchair is occupied even when
using anti-tip levers.
4.1.3.2 Footplate Height
To adjust footplate height use the Karma tool provided to loosen the bolt at the
front of the footrest arm. (See Figure 4.13 )
Adjust to required height and re-tighten. (See Figure 4.13 )
Figure 4.13
Figure 4.14
SUGGESTION:
Make sure that the footplate height is adjusted properly according to the user’s
calf length to reduce pressure on the body.
The footrest height must be more than 5cm. (See Figure 4.14)
4.1.4 Transporting and Storing
SUGGESTION:
Please store the wheelchair in a location where it is out of direct sunlight, rain and
dew. For more details, consult your Karma dealer.
11
WARNING:
Don't put anything on the wheelchair while it is in
storage. Storing goods on a folded or unfolded
wheelchair will cause damage and is not covered under
warranty. (See Right Figure )
4.2 Transferring In and Out
4.2.1 Transferring In
Engage both hand brakes.
Turn the footplates up and swing them to the side.
The user lowers himself/herself into the seat using the armrests for support.
Turn the footplates back down, so that the user can place his feet on them.
Ensure that the heels rest against the heel supports to prevent contact with the
casters.
Release both hand brakes.
CAUTION:
Always ensure that the front casters are in line with the rear wheels and pointing
forwards and that the back of the chair is secure either against a wall or firmly held
by an attendant.
4.2.2 Transferring Out
Make sure that the chair is near your final destination.
Back the chair sufficiently to ensure that the casters are pointing forward, i.e. in
line with the rear wheels and usually with the caster forks pointing forward.
Ensure that, where possible, the rear of the chair is against a wall or, if not, it
must be firmly held by an attendant.
Engage both attendant brakes.
Turn the footplates up.
Slide forwards on the seat.
Place one foot firmly on the ground with the knee at a right angle and the other
foot slightly apart and further back.
Place your hands on the front of the armrests and moving your weight forward,
bring your head and shoulders up over your knees as you push yourself up.
CAUTION:
Never stand on the footplates when getting into (or out of) the chair. (See
Figure 4.15)
When getting in and out of the wheelchair please use the attendant brakes.
Please ensure that neither the tread on your tires nor the brake block has
become too worn. If pneumatic tires are fitted, please maintain at the
recommended tire pressure for the same reason.
When transferring in and out of the chair, make sure that the brakes are applied to
prevent the chair from sliding away. Also see that the footplates are flipped up for
ease of entering or exiting. (See Figure 4.16)
12
4.3 General Use
4.3.1 Attendant Pushing
Ensure that the brakes are always locked when the chair is not being pushed.
(See Figure 4.17)
Always make sure that both feet are safely on the footplates and that clothing is
safely tucked out of the way and cannot get caught in the wheels. (See Figure
4.18)
Always use both hands on the push handles to control the chair. (See Figure
4.19)
Always avoid steep or uneven surfaces because the chair may tip over. (See
Figure 4.20)
Always avoid soft surfaces because the casters may get bogged down. (See
Figure 4.21)
Always be careful not to go too fast or turn too quickly and try to achieve a
smooth steady ride.
Before crossing the road, please stop completely and look both ways.
Cross the rail tracks perpendicular to avoid your wheels getting stuck.
Do not drive at full speed over the railroad tracks.
PLEASE keep in contact with the person in the chair. If you stop to look in shop
windows or talk to people, remember to turn the chair so that the person in the chair
does not have to turn.
WARNING:
Never lock the brakes too suddenly as this may tip the user out of the chair.
Figure 4.15
Figure 4.16
Figure 4.17
Figure 4.18
Figure 4.19
Figure 4.20
13
Figure 4.21
Figure 4.22
4.3.2 Tilting by the Attendant
Make sure both the user's feet are on the footplates and will not slip off. Make
sure the handgrips are secure and cannot slip off.
Release both brakes.
Grasp both push handles firmly.
Put your stronger foot on the relevant tipping lever at the back of the chair.
Tell the person in the chair that you are about to tilt the chair backwards.
Pull back with both hands and push down and forwards with the foot. This will
bring the chair onto the back wheels. (See Figure 4.22)
CAUTION:
When a chair is tilted to about 25 degrees it will balance on its rear wheels and
be easy to hold. If it is tilted further back it will be difficult to hold and the person
in the chair will feel unsafe.
Lower with a straight back; keep your foot on the anti-tipper and lower the chair
slowly forwards softly to the ground.
4.3.4 Going Down Curbs
Please note: It is always better to avoid Curbs where possible by using ramped
Curbs or slopes and this operation is best attempted with the aid of an attendant.
14
4.3.4.1 Going Down Curbs Forwards With an Attendant
CAUTION:
This is the more difficult method and can jar the user but allows a better view of
traffic.
Be careful that the anti-tipper does not get caught on the curb causing the user
to fall.
NEVER ALLOW THE CHAIR TO TIP FORWARDS WHEN GOING DOWN A CURB.
Position the chair so that the front casters are near the edge of the Curb and
make sure that the road is clear.
Move the chair slowly and carefully forwards while tilting it back slightly. Be
ready to take the weight when the rear wheels cross the Curb edge. Ensure
that both rear wheels touch the ground at the same time to avoid tipping the
chair.
Gently lower the front casters. AVOID JARRING THE USER.
4.3.4.2 Going Down Curbs Backwards With an Attendant
CAUTION:
This is the easier and smoother method BUT it requires the attendant to step
backwards into the road.
Back the chair to the Curb edge and be careful that the back wheels are equally
near the edge.
Grasping the push handles, gently lower the rear wheels onto the road. Be
prepared to control the weight as it descends and ensure that the back wheels
touch ground at the same time.
Tilt the chair back slightly and pull the tilted chair far enough into the road so that
the casters and footrests can be lowered clear of the Curb.
4.3.5 Going Up Curbs
Please note: This operation is best attempted with the aid of an attendant and the
best method is to go up Curbs forwards as this maintains the direction of travel and
is physically less demanding for the attendant.
4.3.5.1 Going Up Curbs Forwards With an Attendant
As the footrests nearly touch the Curb tilt the chair. The chair should be tilted
just high enough to allow the front casters to roll smoothly onto the pavement.
Push the chair forward until the rear wheels are touching the Curb. Then,
continuing the movement, lift at the push handles while moving the chair
forwards.
4.3.5.2 Going Up Curbs Backwards With an Attendant
Please note: for safety's sake we do not recommend using this method.
4.3.6 Up and Down Steps/Stairs
Please note: avoid flights of steps particularly if no extra help is available.
ramps or lifts wherever possible.
Two attendants are necessary, each capable of carrying at least half of the
15
Use
combined weight of the person and the wheelchair.
Each helper should bend at the knees and grip the main frame: with the front
attendants hands just under the front of the seat, with the back attendant’s hands
holding the frame just under the push handles.
CAUTION:
Don’t attempt to lift the wheelchair by any removable (detachable) parts. Lifting by
means of any removable (detachable) parts of wheelchair may result in injury to the
user and/or assistant or damage to the wheelchair.
ALL LIFTING SHOULD BE DONE WITH A STRAIGHT BACK.
Straighten legs to lift the chair. Carefully carry it up or down steps; be aware of how
you place your feet -- do not cross them and trip yourself up.
4.4 Transportation
The Ergo Lite (KM-2501) has been crash tested to ISO7176-19 (Report No. MBK
09/0964) and is suitable for use in a vehicle that has been adapted for this purpose.
The wheelchair must be securely restrained as described in this manual. The Ergo
Lite (KM-2501) was tested with a four pint webbing system. For further information
on the use of wheelchair restraints please refer to the manufacturer’s user guide.
Karma always recommends that the user be transferred into car seat with a safety
belt or harness while in a transport.
SUGGESTION:
Please transfer to a seat in the car if at all possible
4.4.1 Before use
Please detach all easily removable accessories from the wheelchair and store
them in a safe place where they cannot move around and become a safety
hazard.
A four point tie-down system should tightly fasten the lower wheelchair frame (hook
mark
) to the transport vehicle.
An occupant restraint system using both a pelvis and harness must also be
fastened to the transport vehicle to insure user safety. Again, please refer to
the restraint system's instructions.
The attendant / transporter must double-check all fastening points for proper
connection and tightness to assure the wheelchair user’s safety. The attendant
/ transporter must be fully aware of the fastening system's usage and its weight
limitations.
See http://www.unwin-safety.com/ for more information.
CAUTION:
When transporting or lifting, never hold on to attachments or accessories (front/rear
wheels, handrims, casters, footrests, armrests, anti-tippers etc.).
All lifting should be done with a straight back. Straight legs to lift the chair. Carefully
carry it up or down steps; be aware of how you place your feet, do not cross them
and trip yourself up.
16
4.4.2 Method of restraint
The Ergo Lite (KM-2501) was tested with four point webbing systems. Please refer
to the restraint manufacturer’s user guide for further details of its operation.
Fitting the front restraint
Connect the straps around the wheelchair frame and caster bracket as pictured
below. The anchor point is marked with a yellow sticker.
Take the brakes off and reverse the wheelchair to tension the front straps. Apply
wheelchair brakes (the brakes should be left on during transport)
Fitting the rear restraint
Attach rear straps into rail approximately 11.8 in behind the wheelchair backrest.
Attached the hooks to the rear frame of the wheelchair as pictured below.
Tension the restraint until the wheelchair is secure.
Fitting the front restraint
Fitting the rear restraint
Fitting seat beat
Fasten the 3 point safety belt around the user.
The occupied wheelchair should be located in a forward-facing configuration,
with the parking brake applied.
Pelvic restraints should make full contact across the front of the body near the
junction of the thigh and pelvic as pictured below (correct seat belt position).
Restrains should not be held away from body by wheelchair components such as
armrest or wheels as pictured below (Incorrect seat belt position).
Correct seat belt position
Incorrect seat belt position
17
4.5 Safety Belt
How to assemble and disassemble the Safety Belt
Loosen the fourth and fifth screws of both side of seat upholstery and insert the
Safety Belt in between the fourth and fifth screw holes. (Figure 4.23.)
Keep the safety Belt in 45 deg for comfortable usage. (Figure 4.24.)
Put the seat upholstery back and tighten screws.
Figure 4.23
Figure 4.24
Adjusting length of seat belt
Identify the require length of the belt. (Figure 4.25.)
Push the two part of belt through buckle to make the belt longer or shorter.
(Figure 4.26.)
Pull the two part of belt tight. (Figure 4.27.)
Push buckle up to the plastic clip so that the belt cannot slip out of position.
Please check that there is no gap between the clip and buckle. (Figure 4.28.)
SUGGESTION:
We recommend that the belt is fitted quite tightly around the pelvis. Please
tighten until you can just get your fingers between user and seat belt. Please
check that the belt is fastened correctly as recommended. If this is not possible
please consult your supplier.
Figure 4.25
Figure 4.26
Figure 4.27
Figure 4.28
How to operate it:
When you sit on the wheelchair, fasten the safety belt.
Adjust the belt and make it fit your body for comfort and security.
When you don’t use it, please fasten the belt to avoid the belt dropping into rear
wheels during motion.
18
Maintenance
The Safety Belt is made from 100% polyester fiber and the clasp is made from
plastic. It does not require any maintenance but should be inspected every month
to ensure that the edges are not frayed and weekly to make sure that it correctly fits
the user. If there are any signs of deterioration, please replace it immediately.
5. INSPECTION AND MAINTENANCE
5.1 General Check
Check the following items before travelling. If you find anything abnormal, visit your
Karma wheelchair dealer for further inspection before using it.
Examine brakes, checking for wear, damage and misalignment. Replacing or
adjusting the brakes should be carried out by your approved repairer.
Check that the hand grips are not damaged and are securely bonded to the push
handles.
Check anti-tippers are not damaged and are securely attached.
Check that the anti-tippers' wheels and frame are not damaged and are securely
mounted.
Before using the wheelchair, make sure all nuts and bolts are tight. Check all
parts for damage or wear and have a qualified technician replace it if necessary.
Check all parts for proper adjustment.
Inspect brakes for proper operation.
The wheels and tires should be checked periodically for cracks and wear, and
should be replaced by a qualified technician.
A qualified technician can be found with an authorized distributor/dealer.
CAUTION:
Visit a Karma wheelchair dealer for inspection and maintenance if you find anything
abnormal.
5.2 Regular Maintenance Record
To make sure your wheelchair is in good condition, visit your Karma wheelchair
dealer regularly for maintenance (and keep records accordingly) every six months
after purchasing.
A maintenance/service fee may apply.
SUGGESTION:
Even if you don't use the vehicle for a long time, the wheelchair should still be
maintained annually.
19
Weekly
Item
GENERAL
Wheelchair rolls straight (no excessive drag or pull to one
side)
FRAME AND CROSS BARS
Inspect frame structure for small cracks/fissures
Monthly
Ⅴ
Ⅴ
Inspect for bent frame or cross bars
Ⅴ
BRAKES
Do not interfere with tires when rolling
Ⅴ
Pivot points free of wear and looseness
Easy to engage
Ⅴ
Prevent chair from moving when engaged
Ⅴ
SEAT & BACKREST
Inspect for rips or sagging
Ⅴ
Inspect for loose or broken hardware
CASTERS
Inspect the casters for smooth rotation of the caster wheel
and caster assembly
Inspect the caster for wear in the bearings/mountings and for
tire wear or damage
REAR WHEELS
Quick-release axles lock properly (if supplied); lubricate if
Ⅴ
necessary
No excessive side movement or binding when lifted and
spun
Inspect for cracked, bent or broken spokes
Ⅴ
ARMRESTS
Inspect the detachable armrest button for effective locking
Ⅴ
Ⅴ
Ⅴ
Ⅴ
FOOTRESTS
Inspect the footplate height adjustment screws are securely
tightened
Inspect the swing-away footrest release lever for effective
locking
TIRES
Inspect for flat spots, cracks and wear
Ⅴ
Ⅴ
Check tire tread depth is more than 1mm
Check tire pressure; tire pressures are located on the side of Ⅴ
the tire
20
Ⅴ
Ⅴ
Make sure the armrest detaches and flips back properly
If pneumatic tires, check for proper inflation
Ⅴ
Ⅴ
Ⅴ
Ⅴ
CAUTION:
As with any wheelchair, the wheels and tires should be checked periodically for
cracks and wear, and should be replaced. Failure to keep tires at the correct
pressure will reduce the braking efficiency.
CAUTION:
Never disassemble or modify the wheelchair frame structure. Otherwise, injury or
damage may occur. This will negate the warranty.
21
6. OPTIONS AND ACCESSARIES
■ I.V. Pole
• Height adjusts from 130cm (51") to
200cm (78").
• Attaches to all Karma manual
wheelchairs.
■ Backrest Bag
• Standard size.
• Attaches to all Karma manual
wheelchairs.
■ Folding Drink Holder
■ Anti-tippers
• Collapses and adjusts to the size of the • Attaches to all Karma manual
container (6-10cm).
wheelchairs.
•Attaches to all Karma manual
wheelchairs.
■ Multi-purpose Safety Belt
• Attaches to all Karma manual
wheelchairs.
CAUTION:
Attaching accessories may alter the overall stability and centre-of-gravity of the
chair. Thus, this should be performed by your approved repairer and therapist.
22
7. TROUBLESHOOTING
Trouble or Problems with Your Wheelchair
You can inspect the following before taking your wheelchair to a Karma wheelchair
dealer.
Problem
Checking Points and Corrective Action
• Check tires for correct and equal pressure
Chair Veers
• Check caster bracket angle
Right/Left
• Check that rear wheels are equally spaced from the
seat frame
2. Sluggish Turn or
• Check tires for correct and equal pressure
Performance
• Check for loose nuts and bolts
• Check tires for correct and equal pressure
3.Caster Flutter/Wobble • Check for loose nuts and bolts
• Check caster bracket angle
4. Squeaks and Rattles
• Check for loose nuts and bolts
5. Looseness in Chair
• Check for loose nuts and bolts
If you cannot solve the problem by yourself, contact your Karma wheelchair dealer
for help.
8. SPECIFICATIONS
Model
Overall Length (in)
Overall Width (in)
Overall Height (in)
Total Weight (lb)(pneumatic rear tire)
Seat Width (in)
Seat Depth (in)
Seat Height (in)
Backrest Height (in)
Armrest Height (in)
Calf Length (in)
Overall Collapsed Length (in)
Overall Collapsed Width (in)
Overall Collapsed Height (in)
Maximum User Weight (lb)
Ergo-Lite(KM-2501)
37
37
22.4
24.5
35.8
18.3
18.5
16”
18”
16.5
19
16.5
8.5
13.8 - 15.7
33.5
10.8
28
220.5
220.5
CAUTION:
Please don't travel across a slope (in any direction) greater than 7 degrees.
Stability (According to ISO 7176-1:1999)
Dummy 220.5 lb
Ergo Lite(KM-2501)
Forward
Backward Rear Wheels Locked
Backward Rear Wheels Unlocked
Anti-tip
Sideways
16°
10.5°
15°
11.5°
16°
23
9. CLEANING & RECYCLING
9.1 CLEANING
In order to lengthen the life of your wheelchair, it is suggested that you clean the
wheelchair periodically (if not daily), especially after it is used in the rain or snow.
We recommend that you don't use your wheelchair in the rain or snow. If you are
travelling and get caught in the rain, we suggest you try to find shelter. If you can't
find shelter, proceed to your destination.
9.1.1 Frame
Wipe with a damp cloth.
9.1.2 Upholstery
When cleaning the upholstery, use warm water and a mild soap.
Upholstery cleaner/foam can also be used, but avoid other cleaning solvents.
9.2 POST-CONSUMER RECYCLING
A post-consumer recycling plan should follow the Environmental Protection
Administration's regulations. The items listed below are for reference only as local
laws and regulations may vary.
Material
Part Name
Method
Aluminum-alloy
Frame
Recyclable
Plastic
Modular Components
Recyclable
Paper
Owner's Manual
Recyclable
There are many organizations in many countries you can find on the Internet that
will accept used goods for charity. Please search the information highway to
help less fortunate individuals and protect our planet for future generations. If
you do not have access to the world wide web please use your local phone
directory, ask for operator assistance or go to your local government centre for
more information. Earth Day is every day.
Check with your local recycling centre on where and how to recycle your
wheelchair as this information varies from region to region.
10. WARRANTY
10.1 Serial Number
To ensure after-sale service and warranty, please record and fill in the serial number
which can be found on the frame.
Model
Serial Number
10.2 U.S.A. Limited Warranty Policy
Karman warrants the main frame of S-ERGO 105, 106, 115, 305, 2501 KM-3520,
KM-802, KM-5000, KM-7501, KM-8020, VIP515, MVP-502 series against defects in
material and workmanship for the lifetime from the date of purchase, 6 months on parts.
Karman warrants the main frame of KM-9020L, KM-TV10, KM-AA10, KM-AA20
against defects in material and workmanship for one year from the date of purchase,
6 months on parts.
This warranty is extended only to original purchasers of our products. Warranty is
not transferable. Parts or materials which are subject to normal wear and which
must be replaced/repaired are the owner’s responsibility and are not covered by
24
warranty. Arm pads and upholsteries are not covered by warranty. It is
recommended that wheelchair be returned to the authorized dealer through whom it
was original purchased.
If within such warranty period, any such product is proven to Karman’s satisfaction
to be defective; such product shall be repaired or replaced at Karman option. In no
case are goods to be returned without first obtaining an R.M.A. (Returned
Merchandise Authorization) number issued by Karman and that the part in question
is returned insured with freight prepaid to Karman, within the period of warranty.
Labor charge incurred in the installation or repair of the above-mentioned parts plus
all freight charges are not included in the warranty.
If Karman does not have a completed Warranty Registration Card on file for the
consumer’s product, then a copy of the invoice with date of purchase must be
provided. The warranty period for the consumer commences on the purchase date
from the seller. The warranty period for the seller, if the products are not to be sold to
a consumer, commences on the invoice date from Karman Healthcare. The warranty
is void on wheelchairs that have had the serial # tag removed or altered.
Products which have been subject to negligence, abuse, improper storage or
handling, improper operation, unauthorized modifications or misuse are not covered
by this warranty. Karman Healthcare will not warrant the frame or any parts
damaged when the maximum weight limit is exceeded. Warranty applies in the U.S.
only.
Karman Healthcare’s sole liability extends to repair or replacement of parts or
components as previously specified. The foregoing is in lieu of all warranties
expressed, implied or statutory, whether written or oral.
25
Filename:
Directory:
Template:
KM-2501Manual
C:\Users\David\Documents
C:\Users\David\AppData\Roaming\Microsoft\Templates\
Normal.dotm
Title:
型號:KP-4 系列使用手冊(KP-40,KP-45)
Subject:
Author:
Guest
Keywords:
Comments:
Creation Date:
1/15/2010 1:45:00 PM
Change Number: 8
Last Saved On: 8/2/2012 3:48:00 PM
Last Saved By:
SALES-M
Total Editing Time: 58 Minutes
Last Printed On: 6/20/2013 4:43:00 PM
As of Last Complete Printing
Number of Pages: 30
Number of Words: 5,643 (approx.)
Number of Characters: 32,171 (approx.)

advertisement

Key Features

  • Durable aluminum alloy frame
  • Pneumatic tires
  • Optional accessories
  • 220.5 lbs weight capacity
  • Transit wheelchair
  • Attendant brakes

Frequently Answers and Questions

How do I assemble the Ergo Lite KM-2501?
No tools are required for assembly. Your wheelchair should be set up by your authorized Karma dealer.
What is the maximum weight capacity of the Ergo Lite KM-2501?
The maximum user weight for the Ergo Lite KM-2501 is 220.5 lbs.
How do I fold and unfold the Ergo Lite KM-2501?
The Ergo Lite KM-2501 folds by pressing the two release levers on the backrest frame. To unfold, pull outwards on the armrests and push down on the frame until the seat is fully lowered.

Related manuals

Download PDF

advertisement