AGENCY STATEMENTS ARE AT THE BOTTOM
OF PAGE 2
This wireless heat / smoke detector is intended for use with
Honeywell controls that support
SiX™ series devices.
FC: This wireless heat / smoke detector is intended for use with
Honeywell controls that support
SiX™ series devices.
SP: This wireless heat / smoke detector is intended for use with
Honeywell controls that support
SiX™ series devices.
PA: This wireless heat / smoke detector is intended for use with
Honeywell controls that support
SiX™ series devices.
Smoke Detector
/ OPEN
Open
OPEN / OPEN
NOTE: Once enrolled, the device cannot be used with another system until it is removed from the current controller. See the controller’s instructions,
FC: NOTE: Once enrolled, the device cannot be used with another system until it is removed from the current controller. See the controller’s instructions,
SP: NOTE: Once enrolled, the device cannot be used with another system until it is removed from the current controller. See the controller’s instructions,
PA: NOTE: Once enrolled, the device cannot be used with another system until it is removed from the current controller. See the controller’s instructions.
To silence the detector:
Enroll / Enroll / Enroll / Enroll
Press the test switch or disarm the system at the controller. If the alarm condition continues, the detector is only quiet for 5 minutes. When programmed in one-goall-go mode, the test switch will not silence the detector.
NOTE: After enrolling and before mounting permanently, conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary.
FC: NOTE: After enrolling and before mounting permanently, conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary.
SP: NOTE: After enrolling and before mounting permanently, conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary.
PA: NOTE: After enrolling and before mounting permanently, conduct Go/No Go tests (see controller’s instructions) to verify adequate signal strength. Adjust the device location and orientation as necessary.
*
Use UL/ANSI Approved canned smoke. / Use UL/ANSI Approved canned smoke. /
Use UL/ANSI Approved canned smoke. / Use UL/ANSI Approved canned smoke.
Mount / Mount /
Mount / Mount
For programming Smoke or Heat alarms and Tamper, see the Controller’s instructions.
NOTE: All smoke detectors programmed in the panel to operate in one-go-all-go mode will sound on alarm.
FC: For programming Smoke or Heat alarms and Tamper, see the Controller’s instructions.
NOTE: If programmed in the panel to operate in one-go-all-go mode, all smoke detectors in the system will sound on alarm
SP For programming Smoke or Heat alarms and Tamper, see the Controller’s instructions.
NOTE: If programmed in the panel to operate in one-go-all-go mode, all smoke detectors in the system will sound on alarm
PA: For programming Smoke or Heat alarms and Tamper, see the Controller’s instructions.
NOTE: If programmed in the panel to operate in one-go-all-go mode, all smoke detectors in the system will sound on alarm
Test / Test
/
Test / Test
LEDS and 85dB SOUNDER / LEDS and 85dB SOUNDER / LEDS and 85dB SOUNDER
/ LEDS and 85dB SOUNDER
R G Sounder Status
Power Up – Enrollment /
Power Up – Enrollment /
Power Up – Enrollment /
Power Up – Enrollment
Power Up – Device enrolled /
Power Up – Device enrolled /
Power Up – Device enrolled/
Power Up – Device enrolled
Normal mode or Communicating with the panel /
Normal mode or Communicating with the panel /
Normal mode or Communicating with the panel /
Normal mode or Communicating with the panel
Maintenance
Maintenance
1
1 /
/ Maintenance
Maintenance 1
1 /
Test Alarm 2
Test Alarm 2
/ Test Alarm 2
/ Test Alarm 2
/
4
Heat Alarm
Heat Alarm
3
3
/ Heat Alarm
/ Heat Alarm
3 /
3
Smoke Alarm /
Smoke Alarm /
Smoke Alarm /
Smoke Alarm
Low Battery / Low Battery /
Low Battery / Low Battery
Tamper Activated /
Tamper Activated /
Tamper Activated /
Tamper Activated
1
See Maintenance Section / See Maintenance Section / See Maintenance Section /See Maintenance Section
2
Test activated by the test switch or from the panel / Test activated by the test switch or from the panel / Test activated by the test switch or from the panel / Test activated by the test switch or from the panel
3 ≥
135 ° F / 57 ° C or Temperature rise of
≥
15 ° F ( 8.33
° C) within 1 minute /
≥
135 ° F (57 ° C) or Temperature rise of
≥
15 °
F (8.33
° C) within 1 minute /
4
≥
135 ° F(57 ° C) or Temperature rise of
≥
15 ° F (8.33
Starts chirping after 7 days, continues until the batteries are replaced or die
° C) within 1 minute /
/ Starts chirping after 7 days, continues until the batteries are replaced or die / Starts chirping after 7 days, continues until the batteries are replaced or die /
Starts chirping after 7 days, continues until the batteries are replaced or die
2014 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc.
All other trademarks are the properties of their respective owners. All rights reserved www.honeywell.com/security
BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above
212° F (100° C) or incinerate. Dispose of used batteries properly. Keep away from children.
FC:BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above
212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children.
Replace Battery /
Replace Battery / Replace Battery
SP: BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above
212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children.
PA: BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above
212° F (100° C) or incinerate. Dispose of used batteries promptly. Keep away from children.
Approval Listings:
FCC / IC
ETL Listed to UL639 cETL Listed to ULC S306-03
RoHS
Specifications:
Range: 0’- 25’/ 0 – 7.6m; Selectable
RF Frequency: 2.4GHz
Battery: 2 x 3V, Lithium; Panasonic CR123A, Duracell DL 123,
Duracell DL 123A, Honeywell 466
Tamper: Wall
Operating Temperature: 32° – 95° F / 0° – 35° C
Relative Humidity: 95% max. (Agency Compliance – 93% max.), non-condensing
Dimensions: 3.78” Diameter x 1.14” Thick / 96 mm Diameter x 29mm
Thick
Product must be tested at least once each year / Le fonctionnement du produit doit
être vérifié au moins une fois par année / El producto debe ser probado al menos una vez al año / O produto deve ser testado pelo menos uma vez por ano
Support / Support / Support / Support https://mywebtech.honeywell.com/
U.S. warranty / U.S. warranty / U.S. garantie / U.S. garantia www.honeywell.com/security/hsc/resources/wa
MyWebTech Warranty
FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation
Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une reception indésirable.
RF Exposure Warning – The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
Mise en Garde Exposition aux Frequences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS
USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Ê800-15961PŠ
800-15961 11/15 Rev C BETA2
