TABLE OF C ONTENTS
A D J U S T I N G Y O U R L C D M O N I T O R --------------
2
• General safety precautions … … … … … … … .… … … … … 2
• Unpacking your monitor … … … … … … … … … … … … … 5
• Viewing angle … … … … … … … … … … … … … … … … … 6
• Connecting your monitor … … … … … … … … … … … 7
• User controls … … … … … … … … … … … … … … … … … … 8
• OSD Functions and adjustments … … … … … … .… ..… … … 9
• Menu adjustments … … … … … … … … … … … .… ..… … … 10
• Refining the picture … … … … … … … … … … .… ..… … … 12
A P P E N D I X -----------------------------------
- 13
• Power management function … … … … … .… ..… … ..… … 13
• Video input terminal
• Display modes
… … … … … … … … … … ..… … ..… 13
… … … … … … … … … … … … .… … … … 14
• Troubleshooting … … … … … … … … … … … … … … … … 15
• Specifications … … … … … … … … … … … … … … … … … 17
Adjusting your lcd monitor
General safety precautions
This Monitor has been engineered and manufactured to assure your safety. Please read this manual and comply with the warnings and the procedures to avoid any serious electrical shock and other serious damage.
1.
Do not place anything heavy, wet or magnetic on the monitor or power cord.
Do not cover the ventilation openings nor touch them with metallic or flammable material.
2.
High temperature can cause troubles.
Avoid operating the monitor in extreme heat, humidity or dusty areas. Extreme temperature may cause discoloration or damages.
Ambient Temperature : 0
°
C
3.
Do not use a solvent, such as benzene, to clean the monitor to prevent any damages to the LCD surface.
4.
Do not use fine tools such as a pin or a pencil near the monitor to prevent any scratch to the LCD surface.
2
Adjusting your lcd monitor
5.
Place the monitor on a flat surface to prevent it from falling.
6.
7.
Do not apply any mechanical shocks to the machine.
Install it in a well-ventilated area or secure enough space for ventilation.
8.
Turn the monitor off before connecting it to the power outlet.
3
Adjusting your lcd monitor
9.
Make sure that the power cord and the other cords are properly connected.
10.
Overloaded AC outlets and extension cords are dangerous. Also, the frayed power cords and the broken plugs may cause electric shock or fire.
11.
Do not open the monitor. There are no user-serviceable components inside.
There is a risk of exposure to highvoltage electricity inside, even when power is turned off. If the display monitor does not operate properly, unplug the power cord and contact your dealer. Handling the electrical equipment carelessly will cause a serious electrical shock and other hazards .
CAUTION : RISK OF ELECTRIC SHOCK, DO NOT OPEN
4
Adjusting your lcd monitor
Unpacking your monitor
Please make sure the following items are included with your monitor.
If you find that any o f these items are missing or appear damaged, contact your dealer immediately.
The power cord can be different depending upon different voltage areas.
5
Adjusting your lcd monitor
Viewing angle
Your monitor was designed to allow you to adjust it to a comfortable viewing angle.
The viewing angle can be adjusted 2
?
to 90
?
forward and backward respectively as indicated by the arrow marks below.
2 ?
90 ?
Caution
Basically when the monitor is in used, please make sure that the monitor is at the safe angle less then 45 degrees.
6
Adjusting your lcd monitor
Connecting your monitor
Be sure to turn the computer off before connecting the monitor
?
Connect the power adaptor cord to the monitor and then to the power supply.
?
After powering on the computer, adjust the display using the various controls provided. For further information on the installation procedure, please refer to the operating guide of the computer being used.
7
Adjusting your lcd monitor
User controls
Front control buttons
AUTO MENU SELECT DOWN UP LED POWER
No. Key name Description
1 AUTO Activates the auto adjustment function.
2 MENU Opens the OSD menu.
8
3 SELECT Selects the main menu items and sub-menu items.
4
5
6
7
◀
▶
LED
Moves to the lower menu item or sub-menu item.
Decreases the value of the parameter.
Moves to the upper menu item or sub-menu item.
Increases the value of the parameter .
Indicates the status of the monitor.
• Green : Normal operation.
• Blinking : Power saving mode or disconnected signal cable.
POWER Turns on/off the monitor.
Adjusting your lcd monitor
OSD Functions and adjustments
Main menu and control selection
Press the MENU key to access the main menu.
Place the color box on the control icon you wish to adjust by pressing using the ◀ or ▶ key.
Press the SELECT key to access the control.
Exit menu
Press the MENU key to exit the OSD screen.
Auto exit
Auto save
The OSD menu will disappear automatically after a few second of inactivity.
Normal mode
The monitor automatically saves the new values when OSD closes.
When the video signal is working in normal display mode, power LED is lit green.
DPMS mode
The LED indicates different status when this unit operates in different power-saving modes.
Out of Range
When an unsuitable signal is detected, the OSD displays an
Out of Range message.
9
Adjusting your lcd monitor
Menu adjustments
10
Icon
Settings and sub-menus
Description
BRIGHTNESS • IMAGE BRIGHTNESS CONTROL
CONTRAST • IMAGE CONTRAST CONTROL
AUTO-ADJUST
• AUTOMATICALLY IMAGE SHARPNESS
CONTROL AND NOISE ELIMINATION.
POSITION • H&V POSITION, CLOCK & PHASE CONTROL.
H-Position • IMAGE H-POSITION CONTROL
V-Position • IMAGE V-POSITION CONTROL
Phase
Clock
• IMAGE WIDTH CONTROL
• IMAGE SHARPNESS CONTROL
AND NOISE ELIMINATION
Icon
Adjusting your lcd monitor
Settings and sub-menus
Description
COLOR • WHITE BALANCE CONTROL
Preset Color 1
Preset Color 2
User Color
• ONE OF FACTORY SET OF WHITE
BALANCE
• ONE OF FACTORY SET OF WHITE
BALANCE
• USER CAN CHANGE THE WHITE
LEVEL
LANGUAGE • LANGUAGE SELECTION
OSD ADJUST
• OSD WINDOW & OSD TIME
CONTROL
Horizontal
Position
Vertical
Position
OSD TIME
INFORMATION • Information of input timing.
• This message is displayed after a few seconds of no input signal. In this mode, the DPMS mode is operated so that the monitor power is off.
• This message is displayed when the input signal refresh rate is out of the supported frequency rate.
• This message is displayed when the input signal refresh rate is not compatible with the frequency rate of
TFT LCD monitor
11
Adjusting your lcd monitor
Refining the picture
Step 1
At first display, a full screen, such as window background or "H" character should be achieved by using editor.
Adjust the screen to the center of the display (LCD), by using the top and bottom display controls (i.e. using Vertical position menu).
Step 2
Step 3
Adjust the screen to the center of the display (LCD) by using the right and left display controls (i.e. using Horizontal position menu).
Adjust the phase until the "H" character displays clear.
Step 4
Step 5 Using the Contrast, Brightness, set the color to your preference.
Step 6
When you finish the adjustment, you can save your settings by pressing on the menu until the OSD screen has disappeared.
12
A P P E N D I X
Power management function
This monitor is equipped with a DPMS(Display Power Management Signaling) function that automatically cuts the power dissipation down to less than 5W when the computer is left unattended.
Although the monitor can be left in power-saving mode for longer periods, we recommend that you turn it off after your daily work.
Status Description
Green Power on.
Blink (Amber/Green) Power saving.
Red
Video input terminal
Non operating / Abnormal operating.
A 15Pin D-Sub connector is used as the input signal connector.
Each pin and assignment is shown in the table below.
Pin No. Signal Name Pin No. Signal Name
4
5
6
7
8
1
2
3
RED
GREEN
BLUE
GROUND
GROUND
RED Ground
GREEN Ground
BLUE Ground
12
13
14
9
10
11
15
N.C.
GROUND
GROUND
DDC SDA
H-Sync
V-Sync
DDC SCL
15Pin D-Sub connector
13
A P P E N D I X
Display modes
For the display modes listed below, the screen image has been optimized during production.
Preset timing modes.
Mode
Display
Mode
Horizontal
Frequency (KHz)
Vertical
Frequency (Hz)
Standard Type
640 x 350
720 x 400
31.5KHz
31.5KHz
70Hz
70Hz
IBM
?
IBM
?
640 x 480 31.5KHz 60Hz Industry Standard
VGA
640 x 480 37.9KHz 72Hz VESA Standard
640 x 480
640 x 480
37.5KHz
43.3KHz
75Hz
85Hz
VESA Standard
VESA Standard
800 x 600
800 x 600
SVGA 800 x 600
800 x 600
800 x 600
1024 x 768
XGA
SXGA
1024 x 768
1024 x 768
1280 x 1024
1280 x 1024
35.2KHz
37.9KHz
48.1KHz
46.9KHz
53.7KHz
48.4KHz
56.5KHz
60.0KHz
64.0KHz
80.0KHz
56Hz
60Hz
72Hz
75Hz
85Hz
60Hz
70Hz
75Hz
60Hz
75Hz
VESA Guidelines
VESA Guidelines
VESA Standard
VESA Standard
VESA Standard
VESA Guidelines
VESA Standard
VESA Standard
VESA Standard
VESA Standard
14
A P P E N D I X
Troubleshooting
Warning : This section will try to anticipate potential problems that you may encounter in the day-to-day use of your monitor.
If after trying the suggested solutions, your monitor’s symptom remains the same, contact your authorized service center.
Troubleshooting problems
Problems Corrective Actions
No Picture
LED ON
LED OFF
LED Amber
• Using OSD, adjust Brightness and Contrast to maximum or reset to their default settings.
• Check the power switch.
• Check if the AC power cord is properly connected to the AC adapter.
• Check if video signal cable is properly connected at the back of monitor.
• Check if the power to computer system is ON.
Display is not clear • Adjust the Frequency and Phase settings.
Too light or too dark • Adjust the Brightness and Contrast settings.
Image is not centered
• Adjust the Horizontal and Vertical position settings using the OSD.
15
A P P E N D I X
Problems Corrective Actions
Out of Range
Picture is scrambled
• Check the maximum resolution and the frequency on the video port of your computer.
• Check the signal cable connection between the computer and monitor.
Picture is fuzzy • Perform Auto adjustment.
Picture bounces or has wavy oscillations
• Check the signal cable connection between computer and monitor.
Picture appears to be ghosting
• Check the signal cable connection between computer and monitor.
Color is not uniform
• Adjust the color settings using the color menu.
The colors are distorted with dark or shadowed areas
The power indicator is
Amber
• Adjust the color settings using the color menu.
• The monitor is using its power management system. Check the power management utility on your computer.
16
A P P E N D I X
Specifications
LCD viewable size
Type 17” viewable diagonal TFT type
Pixel pitch 0.088 mm (H) x RGB x 0.264 mm (V)
Viewable angle L/R : 65
˚
/65
˚
Glass surface Anti-glare, Hard coating.
Contrast ratio
Response time
Display mode
Brightness
INPUT VGA
400:1 (Typical)
25ms(Rising + Falling)
Normally white
250 cd/ m
2
RGB Analog,
Fh : 31.5 to 80 KHz Fv : 56 to 75 Hz
From VGA up to 1280 x 1024 at 75Hz Input resolution
I/O Connectors
Power
User c ontrols
Displayable c olor
Displayable area 337.92mm(H) x 270.336mm(V)
Operation 0
° ° °
F)
Temperature
Storage -20
° ° °
F)
Dimensions Physical
Net
VGA 15-pin D-sub, DC Power in
AC 100~240V, 50/60Hz Input
12V, 5A Max DC Output
Auto-Adjust, Brightness, Contrast, Position,
Color, Language, OSD Adjust
16.7 M (Full Color)
414.6mm(W) x 369.0mm(H) x 170.5mm(D)
4.9Kg
Weight
Gross
Regulations
Plug & play
6.7Kg
UL/cUL, CE, CB, TUV/GS, MPR II, FCC-B,
TCO95, VCCI
VESA DDC 1/2B
Power management VESA DPMS Compatible
17
