LG MU-60PZ 95V plasma monitor Owner’s manual
Below you will find brief information for plasma monitor MU-60PZ95V. This manual will guide you on how to connect your plasma monitor to various external devices and how to set up and use its features, such as the picture and sound settings, timer functions, and PIP/Double Window feature. The guide also includes instructions for connecting to a PC and using the monitor for conferencing, games, and internet browsing.
Advertisement
Advertisement
LG Electronics U.S.A., Inc.
PLASMA MONITOR
OWNER’S MANUAL
MODELS : MU-60PZ95V
Please read this owner’s manual thoroughly before operating the Monitor.
Retain it for future reference.
Record model number and serial number of the Monitor.
See the label attached on the back of the Monitor and relate this information to your dealer if you ever require service.
Model Number :
Serial Number :
Warning
W arning
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING
:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
FCC NOTICE
• A Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is:
LG Electronics U.S.A., Inc
1000 Sylvan Avenue, Englewood Cliffs, NJ 07632
1-201-816-2000 http://www.lgusa.com
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
2 Plasma TV
Warning
* Safety instructions have two kinds of information, and each meaning of it is as below.
WARNING
The violation of this instruction may cause serious injuries and even death.
NOTES
The violation of this instruction may cause light injuries or damage of the product.
Take care of danger that may happen under specific condition.
1.
Do not place the product in direct sunlight or near heat sources such as heat registers, stove and so on.
This may cause a fire.
2.
Do not use the product in damp place such as a bathroom or any place where it is likely to get wet.
This may cause a fire or could give an electric shock.
3.
Bend antenna cable between inside and outside building to prevent rain from flowing in.
This may cause water damaged inside the product and could give an electric shock.
4.
Earth wire should be connected.
- If the earth wire is not connected, there is possible a danger of electric shock caused by the current leakage.
- If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician.
- Do not connect ground to telephone wires, lightning rods or gas pipe.
Power supplier
6.
Do not insert any object into the exhaust vent.
This may cause a fire or could give an electric shock.
7.
Do not place heavy objects on the product.
This may cause serious injury to a child or adult.
8.
Do not use water the product while cleaning.
This may cause damaged the product or could give an electric shock.
9.
In case of smoke or strange smell from the product, switch it off ,unplug it from the wall outlet and contact your dealer or service center.
This may cause a fire or could give an electric shock.
10. Do not attempt to service the product yourself.
Contact your dealer or service center.
This may cause damaged the product or could give an electric shock.
11.During a lightning thunder, unplug the product from the wall outlet and don’t touch an antenna cable.
This may cause damaged the product or could give an electric shock.
Short-circuit breaker
5.
Do not placing anything containing liquid on top of the product.
This may cause a fire or could give an electric shock.
Owner’s Manual 3
Safety Instructions
NOTE
1.
Never touch the power plug with a wet hand.
This may cause an electric shock.
2.
Disconnect from the mains and remove all connections before moving.
3.
Do not place the product in a built-in installation such as a bookcase or rack.
Ventilation required.
4.
When installing the product on a table, be careful not to place the edge of its stand.
This may cause the product to fall, causing serious injury to a child or adult, and serious damage to the product.
5.
Do not place an outside antenna in the vicinity of overhead power lines or other electric light or power circuits.
This may cause an electric shock.
6.
There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls.
This may cause an electric shock.
7.
Do not pull the cord but the plug when unplugging.
This may cause a fire.
8.
Ensure the power cord doesn’t trail across any hot objects like a heater.
This may cause a fire or an electric shock.
9.
Do not plug when the power cord or the plug is damaged or the connecting part of the power outlet is loose.
This may cause a fire or an electric shock.
10. Dispose of used batteries carefully to protect a child from eating them.
In case that it eats them, take it to see a doctor immediately.
11. When moving the product assembled with speakers do not carry holding the speakers.
This may cause the product to fall, causing serious injury to a child or adult, and serious damage to the product.
12. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
This may cause damaged the product or could give an electric shock.
13. Contact the service center once a year to clean the internal part of the product.
Accumulated dust can cause mechanical failure.
14. The distance between eyes and the screen should be about 5 ~ 7 times as long as diagonal length of the screen.
If not, eyes will strain.
15. Unplug the product from the wall outlet when it is left unattended and unused for long periods of time.
Accumulated dust may cause a fire or an electric shock from deterioration or electric leakage.
16. Only use the specified batteries.
This make cause damaged the product or could give an electric shock.
4 Plasma TV
Safety Instructions
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4
Introduction
Controls and Connection Options . . . . . . . . . . . .7
Remote Control Key Functions . . . . . . . . . . . . . .8
Installation
Installation Instructions . . . . . . . . . . . . . . . . . . .9~10
External Equipment Connections . . . . . . . . . .11~14
Antenna Connection . . . . . . . . . . . . . . . . . . . . .12
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . .11
External A/V Source Setup . . . . . . . . . . . . . . . .13
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
DTV Setup / Monitor Out Setup . . . . . . . . . . . . .14
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .15~16
Operation
Turning on the Monitor . . . . . . . . . . . . . . . . . . . . .17
Menu Language Selection . . . . . . . . . . . . . . . . . .17
Picture Menu Options
APC (Auto Picture Control) . . . . . . . . . . . . . . . .18
XD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Color Temperature Control . . . . . . . . . . . . . . . .18
Fleshtone . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
sRGB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Manual Picture Control(Off option) . . . . . . . . . .19
Sound Menu Options
DASP (Digital Auto Sound Processing) . . . . . . .20
BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . .20
Manual Sound Control (Off option) . . . . . . . . . .21
Stereo/SAP Broadcasts Setup . . . . . . . . . . . . .21
Timer Menu Options
Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .22
On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .22
Auto Off / Sleep Timer . . . . . . . . . . . . . . . . . . .22
Special Menu Options
Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
ISM (Image Sticking Minimization) Method . . . .23
Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
XD Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Menu Rotation for Vertical Viewing . . . . . . . . . . .24
Screen Menu Options
Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . .25
Setting Picture Format . . . . . . . . . . . . . . . . . . .25
Screen Position . . . . . . . . . . . . . . . . . . . . . . . .25
Manual Configure . . . . . . . . . . . . . . . . . . . . . .26
Selecting VGA Mode . . . . . . . . . . . . . . . . . . . . .26
Screen Adjustments . . . . . . . . . . . . . . . . . . . . .26
Cinema Mode Setup . . . . . . . . . . . . . . . . . . . . .26
Luminance Noise Reduction . . . . . . . . . . . . . . .27
Initializing (Reset to original factory value) . . . . .27
Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
PIP (Picture-In-Picture)/Double Window Feature
Watching PIP/Double Window . . . . . . . . . . . . ..28
Swapping the PIP/Double Window . . . . . . . . . .28
TV Program selection for PIP . . . . . . . . . . . . . .28
Selecting an Input Signal Source for PIP/Double Window .28
Moving the PIP(PIP Mode only) . . . . . . . . . . . .28
PIP Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
PIP Transparency (PIP Mode only) . . . . . . . . . .28
External Control Device Setup . . . . . . . . . . . . . . . .29~34
IR Code Information . . . . . . . . . . . . . . . . . . . . . . .35~36
Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .37
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39~40
Setup and Operation Checklist
(See pages 11~15 for available connection and operational setup options.)
1. Unpack Monitor and all accessories.
2. Connect all external video and audio equipment.
see pages 11 ~ 15.
3 Install batteries in remote control.
See page 8.
4. Turn Monitor on.
See page 17.
5. Turn video source equipment on.
6. Select viewing source for Monitor.
See page 8.
7. Fine-tune source image and sound to personal preference or as required by source.
See pages 18 ~ 21.
8. Additional features Setup
See Contents above.
After reading this manual, keep it handy for future reference.
Owner’s Manual 5
Introduction
What is a Plasma Display Panel (PDP)?
If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
160° - Wide angle range of vision
Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers who can see the screen anywhere in the room.
Wide Screen
The screen of the Plasma Display is 60" so wide that your viewing experience is as if you are in a theater.
Multimedia
Connect your plasma display to a PC and you can use it for conferencing, games, and internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously.
Versatile
The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs would not fit.
The PDP Manufacturing Process: Why minute colored dots may be present on the PDP screen
The PDP (Plasma Display Panel) which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products and the tiny dots appearing does not mean that this PDP is defective.
Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology is designed to minimize cell defects during the manufacture and operation of this product.
Cooling Fan Noise
In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP.
The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned.
6 Plasma TV
Introduction
- This is a simplified representation of a typical front panel.
The Front Panel Controls shown here may be somewhat different from your monitor.
ON/OFF
INPUT
SELECT
VOLUME
Main Power Button
INPUT SELECT Button Sub Power Button
Power Standby Indicator
Illuminates red in standby mode. Illuminates green when the Monitor is turned on.
VOLUME ( F , G ) Buttons
Remote Control Sensor
REMOTE CONTROL RS-232C INPUT
(CONTROL/SERVICE)
DVI INPUT AUDIO INPUT RGB INPUT RGB OUTPUT
COMPONENT INPUT 2
COMPONENT INPUT 1
Y P
B
P
R
VIDEO
(R)
(L)
AUDIO
(R)
AUDIO VIDEO
MONITOR
OUTPUT
A/V
INPUT 1
S-VIDEO
( ) R ( ) ( ) L ( )
EXTERNAL SPEAKER
AC INPUT
1.
1 2
REMOTE CONTROL
Connect your wired remote control to the remote control port on the Monitor.
3 4 5 6 7 8 9
6.
Monitor Output
Connect a second TV or Monitor.
Audio/Video Input 1
Connect audio/video output from an external device to these jacks.
2.
RS-232C INPUT (CONTROL/SERVICE) PORT
Connect to the RS-232C port on a PC.
3.
DVI (Digital Visual Interface) INPUT/
AUDIO INPUT/ RGB INPUT JACKS
Connect the monitor output connector from a PC to the appropriate input port.
7.
S-Video Input
Connect S-Video out from an S-VIDEO device to the S-
VIDEO input.
4.
RGB OUTPUT PORT
You can watch the RGB signal on another monitor, connect
RGB OUTPUT to another monitor’s PC input port.
8.
EXTERNAL SPEAKER (8 ohm output)
Connect to optional external speaker(s).
* For further information, refer to ‘Speaker & Speaker
Stand’ manual.
5.
DVD/DTV Input (Component 1-2)
Connect a component video/audio device to these jacks.
9.
POWER CORD SOCKET
This Monitor operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the Monitor on DC power.
Owner’s Manual 7
Introduction
- When using the remote control, aim it at the remote control sensor on the monitor.
- Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary.
POWER
Switches the Monitor between
ON and STANDBY.
SLEEP
Sets the Sleep Timer.
(Refer to p.18)
APC
Adjusts the factory preset picture according to the room.
(Refer to p.16)
ARC
Changes the picture format.
(Refer to p.20)
PIP/DW
Switches the sub picture on or off.
(Refer to p.23)
SWAP
Exchanges main and sub picture images. (Refer to p.23, 24)
MENU
Displays on screen menus one by one.
Exits the current menu.
NUMBER buttons
DVD
Control some DVD cassette recorders.
POWER
SLEEP
APC
ARC
PIP/DW
SWAP
MENU
INPUT SELECT
DASP
SPLIT ZOOM
WIN.POSITION
SUB INPUT
MUTE
VOL
OK
VOL
1
4
7
POWER STOP
REW PLAY
8
0
2
5
3
6
9
WIN.SIZE
PAUSE
FF
OPEN/CLOSE
DVD
POWER
STOP
VCR
PAUSE REC
REW PLAY FF
W
WIN.P
INPUT SELECT
Selects source: Video , S-Video ,
RGB , DVI , or Component mode.
DASP
To select the sound appropriate to your viewing program character:
Flat , Music , Cinema , Sports , or
User (Refer to p.17)
SPLIT ZOOM
Enlarges the picture.
WIN.POSITION
Moves the sub picture.
SUB INPUT
Selects the input source for the sub picture.
MUTE
Switches the sound on or off.
OK
D
/
E
Selects menu option.
Memorizes menu changes.
F
/
G
(Volume button)
Increases/decreases sound level.
Adjusts menu settings.
WIN.SIZE
Adjusts the sub picture size.
VCR BUTTONS
Control some video cassette recorders.
• Open the battery compartment cover on the back side and insert the batteries with correct polarity.
• Install two 1.5V alkaline batteries of AAA type. Don’t mix used batteries with new batteries.
8 Plasma TV
Introduction
Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product.
Owner’s Manual
1.5V
1.5V
Alkaline Batteries BNC-RCA Adapter
D-sub 15 pin Cable Power Cord
• The Monitor can be installed in various ways such as on a wall, or on a desktop etc.
• The plasma display is designed to be mounted horizontally or vertically. The speakers shown are optional.
GROUNDING
Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
Short-circuit
Breaker
Power
Supply
W all Mount Installation
For proper ventilation, allow a clearance of 4” on each side and 2” from the wall. Detailed installation instructions are available from your dealer, see the optional
Wall Mounting Bracket Installation and Setup Guide.
2 inches
4 inches
4 inches 4 inches
4 inches
Owner’s Manual 9
Installation
For proper ventilation, allow a clearance of 4” on each side and the top, 2.36” on the bottom, and 2” from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Guide available from your dealer.
4 inches
2 inches
4 inches 4 inches
2.36 inches
W all Mount: V ertical installation (MU-60PZ30M/30V/90C/90M/90V series models only)
Detailed installation instructions are included in the
;;;;;;; optional Vertical Wall Mounting Bracket Installation and
Setup Guide available from your dealer.
NOTE: When installing the monitor vertically, the front panel controls must be in the left side position.
;;;;;;;
;;;;;;;
When installing the monitor vertically, you have to change the OSD display mode so that the menus will appear correctly and also to protect the monitor from overheating
(Refer to P. 19).
;;;;;;;
;;;;;;;
10 Plasma TV
Installation
- Antenna or Cable Service without a Cable Box Connections
- For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket) wall antenna socket
RF coaxial wire (75 ohm)
Bronze Wire
R L/MONO
AUDIO VIDEO
MONITOR
OUTPUT
A/V
INPUT 1
S-VIDEO
Antenna
VHF antenna
UHF antenna
Turn clockwise to tighten.
outdoor antenna
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Bronze Wire
Be careful not to bend the bronze wire when connecting the antenna.
Antenna
Signal
Amplifier
• In a poor signal area to improve picture quality, purchase and install a signal amplifier.
• If the antenna needs to be split for two TV’s, install a “2-Way
Signal Splitter” in the connections.
• If the antenna is not installed properly, contact your dealer for assistance.
Owner’s Manual 11
Installation
NOTE: All cables shown are not included with the TV
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV
- Use the ISM Method (on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time.
Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen.
Connection Option 1
Set VCR output switch to 3 or 4 and then tune
TV to the same channel number.
Connection Option 2
1. Connect the audio and video cables from the
VCR's output jacks to the TV input jacks, as shown in the figure.
When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).
If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular
VCR to the Video input.
2. Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s manual.)
3. Select the input source with using the INPUT
SELECT button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source)
Do not connect to both Video and S-
Video at the same time. In the event that you connect both Video and the
S-Video cables, only the S-Video will work.)
ANT IN
COMPONENT
INPUT 2
COMPONENT
INPUT 1
VIDEO
ANT OUT
S-VIDEO
OUT
OUTPUT
SWITCH
3 4
IN
(R) AUDIO (L) VIDEO
R L
AUDIO
2
VCR
R L/MONO
AUDIO VIDEO
MONITOR
OUTPUT
A/V
INPUT 1
S-VIDEO
Antenna
1
AC INPUT
Cable TV Setup
- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming.
The TV cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the TV.
- For further information regarding cable TV service, contact your local cable TV service provider(s).
Connection Option 1
1. Select 3 or 4 with channel switch on cable box.
2. Tune the TV channel to the same selected output channel on cable box.
3. Select channels at the cable box or with the cable box remote control.
Connection Option 2
1. Connect the audio and video cables from the Cable Box's output jacks to the TV input jacks, as shown in the figure.
When connecting the TV to a Cable Box, match the jack colors
(Video = yellow, Audio Left = white, and Audio Right = red).
2. Select the input source with using the INPUT SELECT button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source)
3. Select your desired channel with the remote control for cable box.
COMPONENT
INPUT 2
COMPONENT
INPUT 1
VIDEO
R L
AUDIO
R L/MONO
AUDIO VIDEO
MONITOR
OUTPUT
A/V
INPUT 1
S-VIDEO
Antenna
2
TV
VCR
(R) AUDIO (L) VIDEO
OUTPUT
SWITCH
3 4
Cable Box
1
RF Cable
AC INPUT
12 Plasma TV
Installation
External A/V Source Setup
How to connect
Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure.
When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio
Right = red).
How to use
1. Select the input source with using the INPUT SELECT button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source).
2. Operate the corresponding external equipment. Refer to external equipment operating guide.
COMPONENT
INPUT 2
COMPONENT
INPUT 1
VIDEO
R
AUDIO
L R L/MONO
AUDIO VIDEO
MONITOR
OUTPUT
A/V
INPUT 1
S-VIDEO
Antenna
AC INPUT
R
AUDIO
L
VIDEO
Camcorder
Video Game Set
How to connect
1. Connect the DVD video outputs (Y, P
B
, P
R
) to the COMPONENT
(Y, P
B
, P
R
) INPUT jacks on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure.
2. If your DVD only has an S-Video output jack, connect this to the
S-VIDEO input on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure.
NOTE: If your DVD player does not have component video output, use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the INPUT SELECT or MULTIMEDIA button on the remote control to select Component 1 or Component 2 . (If connected to
S-VIDEO, select the Video 1 or Video 2 external input source.)
3. Refer to the DVD player's manual for operating instructions.
• Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
Y P
B
P
R
Video output ports on DVD player
Y
Y
Y
Y
Pb
B-Y
Cb
P
B
Pr
R-Y
Cr
P
R
COMPONENT
INPUT 2
COMPONENT
INPUT 1
VIDEO
R L
AUDIO
R L/MONO
AUDIO VIDEO
MONITOR
OUTPUT
A/V
INPUT 1
S-VIDEO
Antenna AC INPUT
B R
(R) AUDIO (L) or S-VIDEO (R) AUDIO (L)
DVD
Owner’s Manual 13
Installation
- To watch digitally broadcast programs, purchase and connect a digital set-top box.
REMOTE
CONTROL
RS-232C INPUT
(CONTROL/SERVICE)
DVI INPUT AUDIO INPUT RGB INPUT
COMPONENT
INPUT 2
COMPONENT
INPUT 1
VIDEO
R L
AUDIO
R L/MONO
AUDIO VIDEO
MONITOR
OUTPUT
A/V
INPUT 1
S-VIDEO
Antenna
DVI-DTV OUTPUT (R) AUDIO (L) or
(R) AUDIO (L) RGB-DTV OUTPUT
Digital Set-top Box or
How to connect
Use the TV’s COMPONENT (Y, P
B
, P
R
) INPUT, RGB or DVI jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections.
How to use
1. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
2. Use INPUT SELECT or MULTIMEDIA on the remote control to select
Component 1 , Component 2 , RGB , or DVI source.
B R (R) AUDIO (L)
Signal
480i
480p
720p
1080i
Component 1/2
Yes
Yes
Yes
Yes
RGB,DVI
No
Yes
Yes
Yes
COMPONENT
INPUT 2
COMPONENT
INPUT 1
VIDEO
R L
AUDIO
R L/MONO
AUDIO VIDEO
MONITOR
OUTPUT
A/V
INPUT 1
S-VIDEO
Antenna
AC INPUT
The TV has a special signal output capability which allows you to hook up a second TV or monitor.
Connect the second TV or monitor to the TV’s MONITOR OUTPUT.
See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings.
NOTE
• Component, RGB-PC/RGB-DTV, DVI-PC/DVI-DTV input sources cannot be used for Monitor out.
S-VIDEO
IN
(R) AUDIO (L) VIDEO
14 Plasma TV
How to connect
1. To get the best picture quality, adjust the PC graphics card to 640x 480, 60Hz.
2. Use the TV’s RGB INPUT or DVI (Digital Visual
Interface) INPUT port for video connections, depending on your PC connector.
• If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of either RGB INPUT or DVI INPUT to display the PC on the TV.
• If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to either RGB or DVI; (the other mode is set to Plug and Play automatically by the TV.)
3. Then, make the corresponding audio connection. If using a sound card, adjust the PC sound as required.
Antenna
RGB INPUT AUDIO INPUT DVI INPUT
AUDIO INPUT
R L
COMPONENT 2
COMPONENT 1
VIDEO INPUT
DVD
/DTV
INPUT
Installation
How to use
1. Turn on the PC and the TV.
2. Turn on the display by pressing the POWER button on the TV's remote control.
3. Use INPUT SELECT or MULTIMEDIA on the remote control to select RGB , or DVI source.
4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.
NOTES: • Use a DVI cable.
• Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter screen saver when possible.
• The synchronization input form for Horizontal and Vertical frequencies is separate.
Owner’s Manual 15
Installation
Monitor Display Specifications (RGB-PC / DVI-PC Mode)
Resolution
640x350
720x400
640x480
800x600
832x624
848x480
Horizontal
Frequency(KHz)
31.468
37.861
31.469
37.927
31.469
35.000
37.861
37.500
43.269
35.156
37.879
46.875
53.674
49.725
31.500
35.000
37.500
Vertical
Frequency(Hz)
70.09
85.08
70.08
85.03
59.94
66.66
72.80
75.00
85.00
56.25
60.31
75.00
85.06
74.55
60.00
70.00
75.00
Resolution
852x480
1024x768
1152x864
1280x960
1280x1024
1360x768
1366x768
Horizontal
Frequency(KHz)
31.500
35.000
37.500
48.363
56.476
60.023
54.348
63.995
67.500
60.000
63.981
47.700
59.625
47.700
59.625
Vertical
Frequency(Hz)
60.00
70.00
75.00
60.00
70.06
75.02
60.05
70.01
75.00
60.00
60.02
60.00
75.02
60.00
75.02
16 Plasma TV
T urning on the Monitor
Turning on the Monitor just after installation
1. Connect power cord correctly.
2. Press the ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby mode. Press the INPUT SELECT button on the Monitor or press the POWER , INPUT SELECT button on the remote control and then the Monitor will switch on.
Turning on the Monitor (power cord is still connected)
1. If the Monitor was turned off with the ON/OFF button on the Monitor
• Press the ON/OFF button on the Monitor to turn the Monitor on.
2. If the Monitor was turned off with the remote control and then the ON/OFF button on the Monitor
• Press the ON/OFF button on the Monitor and then press the INPUT SELECT button on the
Monitor or press the POWER , INPUT SELECT button on the remote control to turn the Monitor on.
Operation
The menus can be shown on the screen in the selected language. First select your language.
1. Press the MENU button and then use D / E button to select the SPECIAL menu.
2. Press the G button and then use D / E button to select Language .
3. Press the G button and then use D / E button to select your desired language.
From this point on, the on-screen menus will be shown in the language of your choice.
4. Press the ENTER button to save.
Owner’s Manual 17
Operation
- APC adjusts the TV to the best picture appearance.
- If adjusting picture options (contrast, brightness, color, sharpness, or tint) manually, APC automatically changes to Off .
1. Press the APC button repeatedly to select the picture appearance setup option as shown below.
Daylight Optimum Night time Off
• You can also adjust APC in the PICTURE menu.
• Daylight , Optimum and Night time settings are preset for good picture quality at the factory and cannot be changed.
- XD is LG Electronic’s unique picture improving technology to display a real HD source through an advanced digital signal processing algorithm.
- When selecting APC options (Clear, Optimum and Soft), XD is automatically change to On.
1. Press the MENU button and then use D
/
E button to select the PICTURE menu.
2. Press the G button and then use D
/
E button to select XD .
3. Press the G button and then use D
/
E button to set On or Off .
4. Press the ENTER button to save.
APC
G
ACC
Fleshtone
Contrast 100
Brightness 55
Color 55
Sharpness 60
Tint 0
Menu Prev.
On
Off
Color T emperature Control
Auto Color Temperature Control
- To initialize values (reset to default settings), select the Normal option.
1. Press the MENU button and then use D
/
E button to select the PICTURE menu.
2. Press the G button and then use D
/
E button to select ACC .
3. Press the G button and then use D
/
E button to select either: Cool (Preset),
Normal (Default), or Warm (Preset).
4. Press the ENTER button to save.
Manual Color Temperature Control ( ACC set to Off option)
- You can adjust red, green, or blue to any color temperature you prefer.
1. Press the MENU button and then use D
/
E button to select the PICTURE menu.
2. Press the G button and then use D
/
E button to select ACC .
3. Press the G button and then use D
/
E button to select User .
4. Press the G button and then use D
/
E button to select Red , Green or Blue .
5. Use the F
/
G button to make appropriate adjustments.
• The adjustment range of Red , Green , and Blue is -30 ~ +30.
6. Press the ENTER button to save.
18 Plasma TV
APC
ACC G
Fleshtone
Contrast 100
Brightness 55
Color 55
Sharpness 60
Tint 0
Menu Prev.
Cool
Normal
Warm
Off
Red 0
Green 0
Blue 0
Fleshtone ( RGB-DTV , and DVI-DTV Mode only)
- Use Fleshtone to select the desired skin color option.
1. Press the MENU button and then use D
/
E button to select the PICTURE menu.
2. Press the G button and then use D
/
E button to select Fleshtone .
3. Press the G button and then use F
/
G button to make appropriate adjustments.
• The adjustment range is 0 ~ 3.
4. Press the ENTER button to save.
APC
ACC
Fleshtone G
Contrast 100
Brightness 55
Color 55
Sharpness 60
Tint 0
Menu Prev.
0
Operation
- If the TV is connected to external equipment using sRGB, set sRGB to On to adjust for the color difference.
1. Press the MENU button and then use D
/
E button to select the PICTURE menu.
2. Press the G button and then use D
/
E button to select sRGB .
3. Press the G button and then use D
/
E button to select On or Off .
4. Press the ENTER button to save.
APC
ACC sRGB G
Contrast 100
Brightness 55
Color 55
Sharpness 60
Tint 0
Menu Prev.
On
Off
Manual Picture Control ( APC set to Off option)
- You can adjust picture contrast, brightness, color, sharpness, and tint options to the levels you prefer.
1. Press the MENU button and then use D
/
E button to select the PICTURE menu.
2. Press the G button and then use D
/
E button to select the desired picture option
( Contrast , Brightness , Color , Sharpness , Tint ) .
3. Press the G button and then use F
/
G button to make appropriate adjustments.
4. Press the ENTER button to save.
APC
ACC
Fleshtone
Contrast 100 G
Brightness 55
Color 55
Sharpness 60
Tint 0
Menu Prev.
Owner’s Manual 19
Operation
DASP (Digital Auto Sound Processing)
- This function lets you enjoy the best sound without any special adjustment because the TV has the appropriate sound options based on the program content.
- If you adjust sound options (Treble and Bass) manually, DASP automatically changes to Off .
1. Press the DASP button repeatedly to select the appropriate sound setup as shown below.
SRS TSXT Flat Music Movie Sports Off
•
• You can also adjust DASP in the SOUND menu.
• SRS TSXT , Flat , Music , Movie , and Sports are preset for good sound quality at the factory and cannot be changed.
is a trademark of SRS Labs, Inc.
• TruSurround XT technology is incorporated under license from SRS Labs, Inc.
- BBE High Definition Sound restores clarity and presence for better speech intelligibility and music realism.
1. Press the MENU button and then use D
/
E button to select the SOUND menu.
2. Press the G button and then use D
/
E button to select BBE .
3. Press the G button and then use D
/
E button to select On or Off .
4. Press the ENTER button to save.
• Manufactured under license from BBE Sound, Inc.
• Treble, Bass or BBE aren’t suitable for SRS TSXT mode.
DASP
BBE G
AVL
Balance 0
Treble 50
Bass 50
On
Off
Menu Prev.
A VL (Auto V olume Leveler)
- AVL maintains an equal sound level; even if you change channels.
1. Press the MENU button and then use D
/
E button to select the SOUND menu.
2. Press the G button and then use D
/
E button to select AVL .
3. Press the G button and then use D
/
E button to select On or Off .
4. Press the ENTER button to save.
DASP
BBE
AVL G
Balance 0
Treble 50
Bass 50
On
Off
Menu Prev.
20 Plasma TV
Manual Sound Control ( DASP set to Off option)
- You can adjust sound options Balance, Treble, and Bass to the levels you prefer.
1.
Press the MENU button and then use D
/
E button to select the SOUND menu.
2. Press the G button and then use D
/
E button to select the desired sound option
( Balance , Treble , Bass ) .
3. Press the G button and then use F
/
G button to make appropriate adjustments.
4. Press the ENTER button to save.
DASP
BBE
AVL
Balance 0 G
Treble 50
Bass 50
Menu Prev.
Stereo/SAP Broadcasts Setup
- The TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; if the broadcaster transmits one additional sound signal in addition to the original one.
- Mono: The primary language is heard from left and right speakers. Signal mode is mono.
- Stereo: The primary language is heard from left and right speakers. Signal mode is stereo.
- SAP: The secondary language is heard from left and right speakers in mono sound.
1. Press the MTS button repeatedly.
Mono Stereo SAP
• Select mono sound mode if the signal is not clear or in poor signal reception areas.
• Stereo , SAP modes are available only if included on the broadcast signal.
Operation
Owner’s Manual 21
Operation
T imer Menu Options
- If current time setting is wrong, reset the clock manually.
1. Press the MENU button and then use D
/
E button to select the TIMER menu.
2. Press the G button and then use D
/
E button to select Clock .
3. Press the G button and then use D
/
E button to set the hour.
4. Press the G button and then use D
/
E button to set the minutes.
5. Press the ENTER button to save.
Clock
Off timer
On timer
Auto off
G - - : - - AM
Menu Prev.
On/Of f T imer Setup
- Timer function operates only if current time has been set.
- Off-Timer function overrides On-Timer function if they are set both set to the same time.
- The TV must be in standby mode for the On-Timer to work.
- If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode.
1. Press the MENU button and then use D
/
E button to select the TIMER menu.
2. Press the G button and then use D
/
E button to select Off timer or On timer .
3. Press the G button and then use D
/
E button to select On .
• To cancel On / Off timer function, select Off .
4. Press the G button and then use D
/
E button to set the hour.
5. Press the G button and then use D
/
E button to set the minutes.
6.
For only On timer function
Press the G button and then use D
/
E button to set the volume level at turn-on.
Press the G button and then use D
/
E button to select the channel at turn-on.
7. Press the ENTER button to save.
Clock
Off timer
On timer
Auto off
Menu Prev.
G On
Off
6 : 30 AM
Volume 17
Auto Of f f
1. Press the MENU button and then use D
/
E button to select the TIMER menu.
2. Press the G button and then use D
/
E button to select Auto off .
3. Press the G button and then use D
/
E button to select On or Off .
4. Press the ENTER button to save.
Clock
Off timer
On timer
Auto off G On
Off
Menu Prev.
Sleep T imer
- The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off.
1. Press the SLEEP button repeatedly to select the number of minutes. First the Off option appears on the screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.
2. When the number of minutes you want is displayed on the screen, press the OK button. The timer begins to count down from the number of minutes selected.
3. To check the remaining minutes before the TV turns off, press the SLEEP button once.
4. To cancel the Sleep Timer, press the SLEEP button repeatedly to select Off .
22 Plasma TV
Operation
- The TV can be set up so that it can only be used with the remote control.
- This feature can be used to prevent unauthorized viewing by locking out the front panel controls.
- This TV is programmed to remember which option it was last set to even if you turn the TV off.
1. Press the MENU button and then use D
/
E button to select the SPECIAL menu.
2. Press the G button and then use D
/
E button to select Key lock .
3. Press the G button and then use D
/
E button to select On or Off .
4. Press the ENTER button to save.
• With the Key lock On, the display ‘ Key lock ’ appears on the screen if any button on the front panel is pressed.
Language
Key lock
ISM Method
Low power
Set ID
Demo
OSD Rotate
G On
Off
Menu Prev.
- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in a ghost image remaining even when you change the image. Avoid allowing a fixed image to remain on the TV's screen for a long period of time.
1. Press the MENU button and then use D
/
E button to select the SPECIAL menu.
2. Press the G button and then use D
/
E button to select ISM Method .
3. Press the G button and then use D
/
E button to select either Normal , White wash , Orbiter or Inversion .
• Normal
If image sticking is never a problem, ISM is not necessary - set to Normal.
• White wash
White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. To return to normal viewing, press any button.
• Orbiter
Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the image will move every 2 minutes: Right → Right → Downside →
Downside
→
Left
→
Left
→
Upside
→
Upside.
• Inversion
Inversion will automatically invert the TV panel color every 30 minutes.
4. Press the ENTER button to save.
Language
Key lock
ISM Method
Low power
Set ID
Demo
OSD Rotate
G Normal
White wash
Orbiter
Inversion
Menu Prev.
Owner’s Manual 23
Operation
- Low power reduces the plasma display power consumption.
1. Press the MENU button and then use D
/
E button to select the SPECIAL menu.
2. Press the G button and then use D
/
E button to select Low power .
3. Press the G button and then use D
/
E button to select On or Off .
• When you select On , the screen darkens.
4. Press the ENTER button to save.
Language
Key lock
ISM Method
Low power G
Set ID
Demo
OSD Rotate
On
Off
Menu Prev.
- Use it to see the difference between XD Demo on and XD Demo off.
1. Press the MENU button and then use D
/
E button to select the SPECIAL menu.
2. Press the G button and then use D
/
E button to select Demo .
3. Press the G button to begin XD Demo .
4. Press the MENU button to stop XD Demo .
Language
Key lock
ISM Method
Low power
Set ID
Demo G
OSD Rotate
To start
Menu Prev.
Menu Rotation for V ertical V iewing
1. Press the MENU button and then use D
/
E button to select the SPECIAL menu.
2. Press the G button and then use D
/
E button to select OSD ( On Screen Display )
Rotate .
3. Press the G button and then use D
/
E button to select Normal or Rotate .
• Select Normal , if the monitor was installed horizontally.
• Select Rotate , if the monitor was installed vertically.
4. Press the ENTER button to save.
Language
Key lock
ISM Method
Low power
Set ID
Demo
OSD Rotate G Normal
Rotate
Menu Prev.
24 Plasma TV
Operation
Auto Adjustment
- RGB (PC) mode only; This function doesn’t work for RGB-DTV mode.
- Automatically adjusts picture position and minimizes image shaking.
- After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment.
- The Auto config.
and Manual config.
are not active in DVI mode.
1. Press the MENU button and then use D
/
E button to select the SCREEN menu.
2. Press the G button and then use D
/
E button to select Auto config.
.
3. Press the G button to run Auto configure.
• When Auto config.
has finished, OK will be shown on screen.
• If the position of the image is still not correct, try Auto adjustment again.
4. In RGB (PC) mode, if the image needs to be adjusted more after using Auto config.
, you can make further adjustments with the Manual config.
option.
Auto config. G
ARC
Position
Manual config
Reset
To set
Menu Prev.
- Caution: If a 4:3 fixed image is on the screen for a long time, it may remain visible.
- Set every aspect ratio for TV, Video, Component 480i sources.
- Use 4:3, or 16:9 for other RGB-PC and DVI-PC sources.
- Horizon is not available for Component (480p,720p,1080i), DTV (480p,720p,1080i) sources.
1. Press the ARC button repeatedly to select the desired picture format. You can also adjust ARC in the SCREEN menu.
• 4:3
Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides.
• 16:9
Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.
• Horizon
Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view.
• Zoom
- Choose Zoom when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped.
- This function works in the following modes:
RGB-PC, RGB-DTV (480p,720p,1080i), DVI-DTV (480p,720p,1080i), COM-
PONENT (480p,720p,1080i).
1. Press the MENU button and then use D
/
E button to select the SCREEN menu.
2. Press the G button and then use D
/
E button to select Position .
3. Press the G button and then use D
/
E
/
F
/
G button to adjust the position.
4. Press the ENTER button to save.
Auto config.
ARC
Position G
Manual config
Reset
F
D
G
E
Menu Prev.
Owner’s Manual 25
1. Press the MENU button and then use D
/
E button to select the SCREEN menu.
2. Press the G button and then use D
/
E button to select Manual config.
.
3. Press the G button and then use D
/
E button to to select Phase or Clock .
4. Use the F
/
G button to make appropriate adjustments.
• The Phase adjustment range is 0 ~ 30.
• The Clock adjustment range is -127 ~ +128.
5. Press the ENTER button to save.
Selecting VGA Mode (RGB-PC mode only)
- To see a normal picture, match the resolution of RGB mode and selection of
VGA mode.
1. Press the MENU button and then use D
/
E button to select the SCREEN menu.
2. Press the G button and then use D
/
E button to select VGA Mode .
3. Press the G button and then use D
/
E button to select the desired VGA resolution.
4. Press the ENTER button to save.
Auto config.
ARC
Position
Manual config G
Reset
Phase 0
Clock 0
Menu Prev.
Auto config.
ARC
Position
Manual config
Reset
VGA Mode G 640x480
848x480
852x480
Menu Prev.
Screen Adjustments (V ideo1-2 and Component 480i mode only)
- Use this function to correct jittering or picture instability while viewing a video tape.
1. Press the MENU button and then use D
/
E button to select the SCREEN menu.
2. Press the G button and then use D
/
E button to select Screen adj.
.
3. Press the G button and then use D
/
E button to select TV or VCR .
• Select the VCR option if watching a VCR.
• Select the TV option for other equipment. (Except VCR)
4. Press the ENTER button to save.
CHANNEL
PICTURE
SOUND
Screen adj.
ARC
Cinema
YNR
Reset
TIMER
SPECIAL
SCREEN
PIP/DW
Menu Prev.
G TV
VCR
Cinema Mode Setup (V ideo1-2 and Component 480i mode only)
- Sets up the TV for the best picture appearance for viewing movies.
1. Press the MENU button and then use D
/
E button to select the SCREEN menu.
2. Press the G button and then use D
/
E button to select Cinema.
.
3. Press the G button and then use D
/
E button to select On or Off .
4. Press the ENTER button to save.
Screen adj.
ARC
Cinema G
YNR
Reset
On
Off
Menu Prev.
26 Plasma TV
Operation
Operation
Luminance Noise Reduction (V ideo 1-2 and Component 480i modes only)
- Use YNR to reduce the picture noise that may appear on the screen.
1. Press the MENU button and then use D
/
E button to select the SCREEN menu.
2. Press the G button and then use D
/
E button to select YNR .
3. Press the G button and then use D
/
E button to select On or Off .
4. Press the ENTER button to save.
Screen adj.
ARC
Cinema
YNR
Reset
G On
Off
Menu Prev.
- Reset is unique to each function: Manual config., Position, Split zoom, PIP position and sub picture size for double window.
- Use the Reset option to initialize the adjusted settings.
1. Press the MENU button and then use D
/
E button to select the SCREEN menu.
2. Press the G button and then use D
/
E button to select Reset .
3. Press the G button.
• You can initialize Position, Split zoom, PIP Transparency, PIP position, PIP size and sub picture size for double window.
Screen adj.
ARC
Cinema
YNR
Reset G
On
Off
Menu Prev.
- Enlarges the picture in correct proportions.
- Split Zoom can be used for all input sources.
- In 2-Split Zoom mode, you can only move the image up or down.
- If an image is enlarged, a section can be viewed without using Split Zoom.
1. Press the SPLIT ZOOM button repeatedly to select either 2, 4, or 9 Split Zoom.
2-Split zoom
1
4
4-Split zoom
1
4
2
5
9-Split zoom
1
4
7
2
5
8
3
6
9
2. Press the number button corresponding to the section you wish to enlarge. You can move within the enlarged picture using the D
/
E /
F
/
G button. To return to normal viewing, press the SPLIT ZOOM button again.
Example of choosing 5.
Section 5 is enlarged to fill the screen.
9-Split zoom
1
4
7
2
5
8
3
6
9
Owner’s Manual 27
Operation
PIP (Picture-In-Picture)/Double W indow Feature
- PIP lets you view 2 different inputs pictures (sources) on your TV screen at the same time. One source will be large, and the other source will show a smaller inset image.
- Double Window mode splits the screen into 2, allowing 2 picture sources to be shown on the TV screen at the same time. Each source is given half the screen.
W atching PIP/Double W indow
Press the PIP/DW button to access the sub picture. Each press of PIP changes the PIP options as shown below.
Moving the PIP (PIP Mode only)
Press the POSITION button.
Press the D
/
E
/
F
/
G button repeatedly until desired position is achieved. The sub picture moves up/down/left/right.
• You can also move the PIP position with Win.position
in the PIP/DW menu.
DW 1
PIP
Off
DW 2
Swapping the PIP / / Double W indow
Use the SWAP button to switch the main and sub pictures.
Win.position
◀
▲
▶
▼
PIP Size
Press the WIN.SIZE
button and then use F
/
G button to change the sub picture size.
• Using the Win.size function in Double Window mode, main and sub picture sizes are changed simultaneously.
Using the Win.size function in PIP mode, sub picture size is changed.
• You can also change the sub picture size with Win.size
in the PIP/DW menu.
Win.size
F G
Main Picture Sub Picture
PIP T ransparency (PIP Mode only)
Main Picture
Press the PIPCH+
Sub Picture
/
PIPCHthe sub picture in PIP mode.
button to select a channel for
- To make the PIP clear or opaque
1. Press the MENU button and then use D
/
E button to select the PIP/DW menu.
2. Press the G button and then use D
/
E button to select PIP
Transparency .
3. Press the G button and then use F
/
G button to adjust
PIP transparency.
4. Use the F
/
G button to make appropriate adjustments.
• The adjustment range of PIP Transparency is 0 ~ 10.
5. Press the ENTER button to save.
Selecting an Input Signal Source for PIP /Double W indow
Use the PIP INPUT button to select the input source for the sub picture. Each press of PIP INPUT button changes the
PIP source.
Main Picture Source
TV, Video 1-2, Component 480i
Component 480p/720p/1080i, RGB and DVI
Available Sub Picture Sources
TV, Video 1-2, Component 480i/480p/720p/1080i, RGB and DVI
TV, Video 1-2, Component 480i
28 Plasma TV
External Control Device Setup
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally.
- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.
- RS-232C connection cables are not supplied with the Monitor.
REMOTE
CONTROL
RS-232C INPUT
(CONTROL/SERVICE)
DVI INPUT AUDIO INPUT RGB INPUT
COMPONENT
INPUT 2
COMPONENT
INPUT 1
VIDEO
R L
AUDIO
R L/MONO
AUDIO VIDEO
MONITOR
OUTPUT
A/V
INPUT 1
S-VIDEO
Antenna
AC INPUT
PC
T ype of Connector; D-Sub 9-Pin Male
7
8
5
6
9
2
3
4
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
RXD
TXD
GND
DTR
DSR
RTS
CTS
2
4
6
3
5
7
8
7-Wire Configurations
(Standard RS-232C cable)
PC PDP
3
6
4
2
5
8
7
TXD
RXD
GND
DSR
DTR
CTS
RTS
D-Sub 9 D-Sub 9
1
5
9
6
RXD
TXD
GND
DTR
DSR
RTS
CTS
2
4
6
3
5
7
8
PC
3-Wire Configurations
(Not standard)
PDP
3
4
6
2
5
7
8
TXD
RXD
GND
DTR
DSR
RTS
CTS
D-Sub 9 D-Sub 9
Owner’s Manual 29
External Control Device Setup
- Use this function to specify a monitor ID number.
- Refer to ‘Real Data Mapping 1’. See page 32.
1. Press the MENU button and then use D
/
E button to select the SPECIAL menu.
2. Press the G button and then use D
/
E button to select Set ID .
3. Press the G button and then use F
/
G button to adjust Set ID to choose the desired monitor ID number. The adjustment range of Set ID is 1 ~ 99.
4. Press the ENTER button to save.
Language
Key lock
ISM Method
Low power
Set ID
Demo
OSD Rotate
G
Menu Prev.
1
• Baud rate :9600 bps (UART)
• Data length : 8 bits
• Parity : None
• Stop bit : 1 bit
• Communication code : ASCII code
* Use a crossed (reverse) cable.
T ransmission / Receiving Protocol
COMMAND 1 COMMAND 2 DATA
(Hexadecimal)
[Command1][Command2][ ][Set ID][ ][Data][Cr]
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Color
10. Tint
11. Sharpness
12. OSD Select
13. Remote Control Lock Mode k
14. PIP/DW k
15. Split Zoom
16. PIP Position k k k k k k k k k k k k k k
17. Treble
18. Bass
19. Balance
20. Color Temperature
21. Red Adjustment
22. Green Adjustment
23. Blue Adjustment
24. PIP Input Source
25. Abnormal State
26. ISM Method
27. Low Power
28. Orbiter Time Setting
29. Orbiter Pixel Setting
30. Picture Size
31. Auto Config j j j j j j k k k k k k k k k r t r l j i f t a b c d e g h k m n p q s u v w
$ y z p q s u
0 ~ 1
0 ~ 6
0 ~ 3
0 ~ 1
0 ~ 1
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 1
0 ~ 1
0 ~ 3
0 ~99
0 ~ 3
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 3
0 ~ 3C
0 ~ 3C
0 ~ 3C
0 ~ 6
0 ~ a
0 ~ 3
0 ~ 1
1 ~ FE
1~9
0 ~14
1
* [Command 1]: First command to control PDP set. (j, k or m)
* [Command 2]: Second command to control PDP set.
* [Set ID]: You can adjust the set ID to choose desired monitor
ID number in Special menu. Adjustment range is 1
~ 99. When selecting Set ID ‘0’, every connected
PDP set is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal
(0x0~0x63) on transmission/receiving protocol.
* [DATA]: To transmit command data.
Transmit ‘FF’ data to read status of command.
* [Cr]: Carriage Return
ASCII code ‘0x0D’
* [ ]: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The Monitor transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors.
Data 1: Illegal Code
COM-
MAND 1
COM-
MAND 2
DATA 0 DATA 1 DATA 2 DATA 3
(Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal)
2: Not supported function
3: Wait more time
32. Tune Command m a
33. Channel Add/Del m b
34. Key m c
01 ~ 7D
0 ~ 1
Key code
0 0 mainsub/TuneBand
30 Plasma TV
Transmission
External Control Device Setup
01. Power (Command2:a)
G
To control Power On/Off of the TV.
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data 0 : Power Off
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
1 : Power On
* In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function.
02. Input Select (Command2:b) (Main Picture Input)
G
To select input source for the TV.
You can also select an input source using the TV/VIDEO button on the TV's remote control.
Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Data 0 : TV
1 : Video 1
2 : Video 2
3 : Component 1
Acknowledgement
4 : Component 2
5 : RGB
6 : DVI
[b][ ][Set ID][ ][OK][Data][x]
05. Volume Mute (Command2:e)
G
To control volume mute on/off.
You can also adjust mute using the MUTE button on remote control.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data 0 : Volume mute on (Volume off)
1 : Volume mute off (Volume on)
Acknowledgement
[e][ ][Set ID][ ][OK][Data][x]
06. Volume Control (Command2:f)
G
To adjust volume.
You can also adjust volume with the volume buttons on remote control.
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
•
Refer to ‘Real data mapping 1’ as shown below.
Acknowledgement
[f][ ][Set ID][ ][OK][Data][x]
07. Contrast (Command2:g)
G
To adjust screen contrast.
You can also adjust contrast in the Picture menu.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
•
Refer to ‘Real data mapping 1’ as shown below.
Acknowledgement
[g][ ][Set ID][ ][OK][Data][x]
03. Aspect Ratio (Command2:c) (Main picture format)
G
To adjust the screen format.
You can also adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
Screen menu.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 0 : Normal screen (4:3)
1 : Wide screen (16:9)
2 : Horizon
3 : Zoom
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
04. Screen Mute (Command2:d)
G
To select screen mute on/off.
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data 0 : Screen mute off (Picture on)
1 : Screen mute on (Picture off)
Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
08. Brightness (Command2:h)
G
To adjust screen brightness.
You can also adjust brightness in the Picture menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
•
Refer to ‘Real data mapping 1’ as shown below.
Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
* Real data mapping 1
0 : Step 0
A : Step 10 (SET ID 10)
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
63 : Step 99 (SET ID 99)
64 : Step 100
Owner’s Manual 31
External Control Device Setup
09. Color (Command2:i)
G
To adjust the screen color.
You can also adjust color in the Picture menu.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
•
Refer to ‘Real data mapping 1’. See page 32.
Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
10. Tint (Command2:j)
G
To adjust the screen tint.
You can also adjust tint in the Picture menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data Red : 0 ~ Green : 64
•
Refer to ‘Real data mapping 1’. See page 32.
Acknowledgement
[j][ ][Set ID][ ][OK][Data][x]
11. Sharpness (Command2:k)
G
To adjust the screen sharpness.
You can also adjust sharpness in the Picture menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
•
Refer to ‘Real data mapping 1’. See page 32.
Acknowledgement
[k][ ][Set ID][ ][OK][Data][x]
12. OSD Select (Command2:l)
G
To select OSD (On Screen Display) on/off.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 0: OSD off 1: OSD on
Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
13. Remote Control Lock Mode (Command2:m)
G
To lock the remote control and the front panel controls on the monitor.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 0: Lock off
Acknowledgement
1: Lock on
[m][ ][Set ID][ ][OK][Data][x]
•
If you’re not using the remote control and front panel controls on the monitor, use this mode. When main power is on/off, remote control lock is released.
32 Plasma TV
14. PIP / DW (Command2:n)
G
To control the PIP (Picture In picture)/DW (Double Window).
You can also control the PIP/DW using the PIP/DW button on the remote control or in the PIP/DW menu.
Transmission
[k][n][ ][Set ID][ ][Data][Cr]
Data 0: PIP/DW off
1: PIP
Acknowledgement
[n][ ][Set ID][ ][OK][Data][x]
2: DW1
3: DW2
15. Split Zoom (Command2:p)
G
To operate split zoom function and select the split zoom section number.
Transmission
[k][p][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max:99
•
Refer to ‘Real data mapping 2’.
Acknowledgement
[p][ ][Set ID][ ][OK][Data][x]
* Real data mapping 2
0 : Reset split zoom
21: Selection 1 of 2 split zoom
24: Selection 4 of 2 split zoom
41: Selection 1 of 4 split zoom
42: Selection 2 of 4 split zoom
44: Selection 4 of 4 split zoom
45: Selection 5 of 4 split zoom
91: Selection 1 of 9 split zoom
99: Selection 9 of 9 split zoom
16. PIP Position (Command2:q)
G
To select sub picture position for PIP.
You can also adjust the sub picture position using
WIN.POSITION on the remote control or in the PIP/DW menu.
Transmission
[k][q][ ][Set ID][ ][Data][Cr]
Data 0: Right down on screen
1: Left down on screen
2: Left up on screen
3: Right up on screen
Acknowledgement
[q][ ][Set ID][ ][OK][Data][x]
17. Treble (Command2:r)
G
To adjust treble.
You can also adjust treble in the Sound menu.
Transmission
[k][r][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
•
Refer to ‘Real data mapping 1’. See page 32.
Acknowledgement
[r][ ][Set ID][ ][OK][Data][x]
External Control Device Setup
18. Bass (Command2:s)
G
To adjust bass.
You can also adjust bass in the Sound menu.
Transmission
[k][s][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
•
Refer to ‘Real data mapping 1’. See page 32.
Acknowledgement
[s][ ][Set ID][ ][OK][Data][x]
19. Balance (Command2:t)
G
To adjust balance.
You can also adjust balance in the Sound menu.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
•
Refer to ‘Real data mapping 1’. See page 32.
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
20. Color Temperature (Command2:u)
G
To adjust color temperature.
You can also adjust ACC in the Picture menu.
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Data 0: Cool 1: Normal 2: Warm 3: User
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
21. Red Adjustment (Command2:v)
G
To adjust red in color temperature.
Transmission
[k][v][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 3C
•
Refer to ‘Real data mapping 3’ as shown right.
Acknowledgement
[v][ ][Set ID][ ][OK][Data][x]
22. Green Adjustment (Command2:w)
G
To adjust green in color temperature.
Transmission
[k][w][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 3C
•
Refer to ‘Real data mapping 3’ as shown right.
Acknowledgement
[w][ ][Set ID][ ][OK][Data][x]
23. Blue Adjustment (Command2:$)
G
To adjust blue in color temperature.
Transmission
[k][$][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 3C
•
Refer to ‘Real data mapping 3’ as shown below.
Acknowledgement
[$][ ][Set ID][ ][OK][Data][x]
* Real data mapping 3
0 : -30
1 : -29
2 : -28
1E : 0
3A : +28
3B : +29
3C : +30
24. PIP Input Select (Command2:y)
G
To select input source for sub picture in PIP mode.
Transmission
[k][y][ ][Set ID][ ][Data][Cr]
Data 0 : TV
1 : Video 1
2 : Video 2
3 : Component 1
4 : Component 2
5 : RGB
6 : DVI
Acknowledgement
[y][ ][Set ID][ ][OK][Data][x]
25. Abnormal State (Command2:z)
G
To recognize an abnormal state.
Transmission
[k][z][ ][Set ID][ ][FF][Cr]
Data FF:Read
Acknowledgement
[z][ ][Set ID][ ][OK][Data][x]
Data 0: Normal (Power on and signal exist)
1: No signal (Power on).
2: Turn the monitor off with remote control.
3: Turn the monitor off with Sleep Time function.
4: Turn the monitor off with RS-232C function.
5: 5V down.
6: AC down.
7: Turn the monitor off with Fan Alarm function.
8: Turn the monitor off with Off Time function.
9: Turn the monitor off with Auto Off function.
a: Turn the monitor off with On Time function.
(If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode.)
* This function is “read only”.
Owner’s Manual 33
26. ISM Method (Command2:p)
G
To avoid having a fixed image remain on screen.
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data 0: Normal
1: White wash
Acknowledgement
[p][ ][Set ID][ ][OK][Data][x]
2: Orbiter
3: Inversion
27. Low Power (Command2:q)
G
To control the low power function on/off.
Transmission
[j][q][ ][Set ID][ ][Data][Cr]
Data 0: Low power off
1: Low power on
Acknowledgement
[q][ ][Set ID][ ][OK][Data][x]
28. Orbiter Time Setting (Command2:r)
G
To adjust orbiter operation time term.
Transmission
[j][r][ ][Set ID][ ][Data][Cr]
Data Min: 1 ~ Max: FE
Acknowledgement
[r][ ][Set ID][ ][OK][Data][x]
29. Orbiter Pixel Setting (Command2:s)
G
To adjust pixel number in orbiter function.
Transmission
[j][s][ ][Set ID][ ][Data][Cr]
Data Min: 1 ~ Max: 9
Acknowledgement
[s][ ][Set ID][ ][OK][Data][x]
30. Picture Size Setting for Double Window mode (Command2:t)
G
To adjust main window size in Double Window mode.
Transmission
[j][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 14
•
Refer to ‘Real data mapping1’. See page 32.
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
34 Plasma TV
External Control Device Setup
31. Auto Configure (Command2:u)
G
To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode.
Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data 1: To set
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
32. Tune command (Command: m a)
G
Tune channel to following physical number
Transmission
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][ ][Data3][Cr]
Data 0: Air: 02 ~ 45, Cable: 01, 0E ~ 7D
1: 0
2: 0
3: High
→
Main Channel: 0, Sub Channel: 1
Low
→
Air: 0, CATV: 1
Acknowledgement
[a][ ][Set ID][ ][OK][Data0][x][ ][Data1][x][ ][Data2][x][ ][Data3][x]
33. Channel Add/Del (Command: m b)
G
To add and delete the channels
Transmission
[m][b][ ][Set ID][ ][Data][Cr]
Data 0: Channel Memory
1: Channel Erase
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
34. Key (Command: m c)
G
To send IR remote key code
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
Data Key code: Refer to page 37.
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
IR Codes
G
Connect your wired remote control to the Remote Control port on the Monitor.
G
Output waveform
Single pulse, modulated with 37.917KHz signal at 455KHz
T
C
Carrier frequency
T1
F
CAR
= 1/T
C
= f
OSC
/12
Duty ratio = T1/T
C
= 1/3
G
Configuration of frame
• 1st frame
Lead code
Low custom code
High custom code
Data code Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
• Repeat frame
Repeat code
T f
G
Lead code
G
Repeat code
9 ms 4.5 ms
0.55 ms
9 ms
2.25 ms
G
Bit description
• Bit “0” • Bit “1”
0.56 ms
1.12 ms
G
Frame interval : Tf
The waveform is transmitted as long as a key is depressed.
Tf Tf
0.56 ms
2.24 ms
Tf=108ms @455KHz
Owner’s Manual 35
Code (Hexa) Function
CH ( D )
CH ( E )
VOL ( G )
VOL ( F )
POWER
POWER ON
POWER OFF
MUTE
Number Key 0
Number Key 1
Number Key 2
Number Key 3
Number Key 4
Number Key 5
Number Key 6
Number Key 7
Number Key 8
Number Key 9
TV/VIDEO
MULTIMEDIA
TV
VIDEO1
VIDEO2
COMPONENT1
COMPONENT2
DVI
RGB
SLEEP
MENU
ENTER
APC
DASP
PIP/DW
PIP INPUT
SWAP
WIN.SIZE
POSITION
PIP CH+
PIP CH-
SPLIT ZOOM
ARC
ARC (4:3)
ARC (16:9)
ARC (Zoom)
FCR
REVIEW
AUTO PROGRAM
MEMORY/ERASE
MTS
CAPTION
AUTO CONFIG
61
63
64
62
71
43
44
4D
52
60
BF
D4
C6
D5
0E
0B
98
D6
5A
D0
AF
1E
1A
54
55
72
7B
79
76
77
0A
39
99
15
16
17
18
19
10
11
12
13
14
00
01
02
03
08
C4
C5
09
Note
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (Power On/Off)
Discrete IR Code (Only Power On)
Discrete IR Code (Only Power Off)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code (Input TV Selection)
Discrete IR Code (Input VIDEO1 Selection)
Discrete IR Code (Input VIDEO2 Selection)
Discrete IR Code (Input COMPONENT1 Selection)
Discrete IR Code (Input COMPONENT2 Selection)
Discrete IR Code (Input DVI Selection)
Discrete IR Code (Input RGB Selection)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code (Only 4:3 mode)
Discrete IR Code (Only 16:9 mode)
Discrete IR Code (Only Zoom mode)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code
IR Codes
36 Plasma TV
Troubleshooting Checklist
T roubleshooting Checklist
No picture &
No sound
• Check whether the TV is turned on.
• Is the power cord inserted into wall power outlet?
• Test the wall power outlet, plug another product’s power cord into the outlet where the TV’s power cord was plugged in.
Picture OK &
No sound
The remote control doesn’t work
• Press the VOLUME ( G ) button.
• Sound muted? Press MUTE button.
• Check to see if there is any object between the TV and the remote control causing obstruction.
• Are batteries installed with correct polarity (+ to +, - to -)?
(Refer to p.9)
• Correct remote operating mode set: TV, VCR etc.?
• Install new batteries. (Refer to p.8)
Picture appears slowly after switching on
• This is normal, the image is muted during the TV startup process. Please contact your service center, if the picture has not appeared after five minutes.
No or poor color or poor picture
• Select Color in the Picture menu and press the VOLUME ( G ) button.
(Refer to p.18)
• Keep a sufficient distance between the TV and the VCR.
• Activate any function to restore the brightness of the picture.
(If still picture is on the screen for more than 5 minutes, the screen gets dark.)
Horizontal/vertical bars or picture shaking
• Check for local interference such as an electrical appliance or power tool.
No output from one of the speakers
• Adjust Balance in the Sound menu. (Refer to p.20)
Unusual sound from inside the TV
• A change in ambient humidity or temperature may result in an unusual noise when the plasma display is turned on or off and does not indicate a fault with the TV.
Owner’s Manual 37
Maintenance & Specification
- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new Monitor. Be sure to turn the power off and unplug the power cord before you begin any cleaning.
1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.
2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your Monitor.
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
Please be sure not to use a wet cloth.
Extended Absence
If you expect to leave your Monitor dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges.
MODELS
Width (inches / mm)
Height (inches / mm)
Depth (inches / mm)
Weight (pounds / kg)
Power requirement
Resolution
Color
Operating Temperature Range
Operating Humidity Range
Maximum Elevation
MU-60PZ95V
57.3 / 1455
84.3 / 883
3.9 / 99
144 / 65.3
AC120V, 60Hz
1366 x 768 (Dot)
16,770,000 (256 steps of each R, G and B)
32 ~ 104°F (0 ~ 40°C)
Less than 80%
6561 feet (2000m)
• The specifications shown above may be changed without notice for quality improvement.
38 Plasma TV
LG ELECTRONICS, INC.
PLASMA DISPLAY PANEL — U.S. LIMITED WARRANTY
Your LG Plasma Display Panel will be repaired or replaced in accordance with the terms of this warranty, at LGE’s option, if it proves to be defective in material or workmanship under normal use, during the warranty period
(“Warranty Period”) listed below, effective from the date (“Date of Purchase”) of original consumer purchase of the product. This warranty is good only to the original purchaser of the product and effective only when used in the
United States, including Alaska, Hawaii, and U.S. Territories.
WARRANTY PERIOD: HOW SERVICE IS HANDLED:
LABOR and PARTS: 2 YEARS from the Date of Purchase.
Your unit will be repaired or replaced with a new, substitute model or factory reconditioned unit, at LGE’s option. If repaired, parts used in the repair may be new or remanufactured.
Replacement Units and Repair Parts are warranted for the remaining portion of the original unit’s warranty period.
EFFECTIVE DATE OF WARRANTY: Your warranty period begins on the date of sale to the original consumer/end user.
KEEP THE DEALER’S DATED BILL OF SALE OR PROOF OF
DELIVERY as evidence of the purchase date. You will be required to submit a legible copy of your bill of sale or proof of delivery when requesting warranty service.
In-Home Service: Please retain dealer’s dated bill of sale or delivery ticket as evidence of the Date of Purchase for proof of warranty, and submit a copy of the bill of sale to the service person at the time warranty service is provided.
Please call 1-201-816-2000 to locate your nearest LGE Authorized Service Center.
Visit our website at: http://www.lgservice.com
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE
EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS
WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS U.S. DISTRIBUTOR SHALL BE
LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY
NATURE, INCLUDING WITHOUT LIMITATION, LOST PROFITS, LOST OR CORRUPTED PROGRAMMING OR
DATA, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights that vary from state to state.
CONCERNING PIXEL FUNCTIONALITY: Your Plasma Display Panel contains about one million individual pixels.
Plasma Display Panel typically contain a small number of pixels that do not function normally. Your display has been inspected and is in compliance with manufacturer’s specifications, indicating that any pixel defects do not effect the operation or use of your display.
IMPORTANT: Please fill out and mail in your Product Registration Card or go to www.lgservice.com to register your product online. This information will allow us to reach you promptly should we discover a safety or reliability problem that could affect you.
THIS LIMITED WARRANTY DOES NOT APPLY TO:
●
●
●
●
●
●
●
● damage caused in shipping or transit service required as a result of improper installation, including incorrect or insufficient AC supply (please consult the owner’s manual for power supply requirements) installation or repair of antenna systems, cable converters, cable company supplied equipment, or other components in a video system set-up or adjustment on consumer controls, or damage caused by improper adjustments damage caused by other system components any panel that has been modified or incorporated into any other product replacement of batteries on the remote control.
damage (including cosmetic damage), failure, loss or personal injury due to misuse, abuse, negli-
●
●
●
●
● gence, improper maintenance or storage, or to acts of nature or other causes beyond our control.
(Causes beyond our control include but are not limited to lightning strike, power surges, power outages and water damage.) image burn-in repair or replacement of warranted parts by other than LGE authorized service centers. units purchased or serviced outside of the coverage area. product where the original factory serial numbers have been removed, defaced or changed in any way. product sold and labeled as “as is, where is” or similar disclaimer.
The cost of repair or replacement under these excluded circumstances shall be borne by the consumer.
CUSTOMER INTERACTIVE CENTER NUMBERS:
To obtain customer assistance, product information or Dealer or Service locations
Call 1-201-816-2000
24 hours a day, 365 days per year
FOR SERVICE:
Before you call for warranty service, check your operating guide – you may avoid a service call.
For warranty service information, please contact the LGE Customer Interactive Center telephone number.
When calling for service, please have your product model number, serial number and the date of purchase or the date of original installation available.
If a replacement unit is required, under some circumstances you may be asked to provide a reserve deposit to the LGE Service Center against a credit card number as surety for advanced shipment. Your credit card will not be charged if you return the defective unit within 10 working days.
If a replacement unit is received, please use the carton and packaging from that unit in returning the defective unit to the LG ® Brand Service Center.
Parts and service in accordance with the LGE warranty are LGE’s responsibility and will be provided without charge. Other service requirements will be at the owner’s expense. If you have problems in obtaining satisfactory warranty service, write or call the LGE Customer Interactive Center. Service may be provided by independently owned and operated service organizations.
To assure proper credit and avoid unnecessary charges, you must obtain an LGE Return Authorization before returning any product to the LGE Service Center. Contact the Customer Interactive Center for details.
TO CONTACT THE LGE CUSTOMER SERVICE CENTER BY MAIL:
LGE Customer Interactive Center
P.O. Box 240007
201 James Record Road
Huntsville, Alabama 35824 http://www.lgservice.com
P/N : 3828VA0470M (RF043A)
Download
Public link updated
The public link to your chat has been updated.
Document public link
Advertisement
Key features
- 160° Wide Viewing Angle
- Wide Screen
- Multimedia Capabilities
- Picture-in-Picture Function
- Thin and Lightweight
