LG Electronics USA BEJN224WHAT LCDMonitor User Manual

Add to My manuals
29 Pages

advertisement

LG Electronics USA BEJN224WHAT LCDMonitor User Manual | Manualzz

OWNER’S MANUAL

NETWORK MONITOR

Please read this manual carefully before operating your set and retain it for future reference.

NETWORK MONITOR MODEL www.lg.com

Accessories

Thank you for purchasing this LGE product

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

OWNER'S MANUAL

/Cards

15-pin D-SUB Signal Cable

(To set it up, this signal cable may be attached to this product before shipping out.)

Power Cord AC-DC adapter

(Depending on the country)

Or

AC-DC adapter

(Depending on the country)

USB Extension Cable

IMPORTANT

This accessories may look different from those shown here.

User must use shielded signal interface cables (D-SUB 15 pin cable) with ferrite cores to maintain standard compliance for the product.

Important Precautions

This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing.

On Safety

Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement.

The appliance coupler is used as the disconnect device.

Please make sure the device is installed near the wall outlet to which it is connected and that the outlet is easily accessible.

Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer.

Overloaded AC outlets and extension cords are dangerous. So are frayed power cords and broken plugs. They may result in a shock or fire hazard. Call your service technician for replacement.

As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if the unit is turned off.

Do not Open the Display:

There are no user serviceable components inside.

There are Dangerous High Voltages inside, even when the power is OFF.

Contact your dealer if the display is not operating properly.

To Avoid Personal Injury :

Do not place the display on a sloping shelf unless properly secured.

Use only a stand recommended by the manufacturer.

Do not drop an object on or apply impact to the product. Do not throw any toys or objects on the product screen.

It can cause injury to human, problem to product and damage the display.

To Prevent Fire or Hazards:

Always turn the display OFF if you leave the room for more than a short period of time. Never leave the display ON when leaving the house.

Keep children from dropping or pushing objects into the display's cabinet openings. Some internal parts carry hazardous voltages.

Do not add accessories that have not been designed for this display.

When the display is to be left unattended for an extended period of time, unplug it from the wall outlet.

In the presence of thunder and lightning, never touch the power cord and signal cable because it can be very dangerous. It can cause electric shock.

1

Important Precautions

On Installation

Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage.

Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.

Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures which may result in a fire hazard. Therefore, NEVER:

Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.

Place the display in a built-in enclosure unless proper ventilation is provided.

Cover the openings with cloth or other material.

Place the display near or over a radiator or heat source.

Do not rub or strike the Active Matrix LCD with anything hard as this may scratch, mar, or damage the Active Matrix LCD permanently.

Do not press the LCD screen with your finger for a long time as this may cause some afterimages.

Some dot defects may appear as Red, Green or Blue spots on the screen.

However, this will have no impact or effect on the display performance.

If possible, use the recommended resolution to obtain the best image quality for your LCD display. If used under any mode except the recommended resolution, some scaled or processed images may appear on the screen. However, this is characteristic of the fixed-resolution LCD panel.

Leaving a fixed image on the screen for a long time may cause damage to the screen and cause image burn-in. Make sure to use a screen saver on the product.

Burn-in and related problems are not covered by the warranty on this product.

Do not shock or scratch the front and sides of the screen with metallic objects.

Otherwise, it may cause damage to the screen.

Make sure the panel faces forward and hold it with both hands to move. If you drop the product, the damaged product can cause electric shock or fire. Contact an authorized the service center for repair.

Avoid high temperatures and humidity.

2

Important Precautions

On Cleaning

Unplug the display before cleaning the face of the display screen.

Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock.

When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur. (Do not use chemicals such as benzene, paint thinners or alcohol)

Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame; wipe in one direction only. Too much moisture may cause staining.

On Repacking

Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit to another location, repack it in its original material.

On Disposal

(Only , Hg lamp used LCD Monitor)

The fluorescent lamp used in this product contains a small amount of mercury.

Do not dispose of this product with general household waste.

Disposal of this product must be carried out in accordance to the regulations of your local authority.

3

Important Precautions

NOTE

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTRERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS

EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY

TO OPERATE THE EQUIPMENT.

NOTE

This epuipment has been tested and found to comply with the limits for a class

B digital device,pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates,uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However,there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and the receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

A3

Connecting the Display

Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off.

Connecting the stand

1 . Place the monitor with its front facing downward on a cushion or soft cloth.

2 .

Assemble the Stand Base into the Stand Body.

Be sure don't pull out the Stop Pin and make the Stand Base direction as shown.

Stand Base

Side Stop Pin

Stand Body

FRONT

3 .

Make the monitor stand , then pull out the Stop Pin.

Warning: The tape and locking pin may only be removed from those monitors equipped with a standing base when the base is pulled up. Otherwise, you may be injured by the protruding sections of the stand.

pull out the stop pin

Stop Pin

Stop Pin

Important

This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture.

Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot.

4

Connecting the Display

Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off.

Positioning your display

1.

Adjust the position of the panel in various ways for maximum comfort.

Tilt Range: -6˚ to 17˚

-6˚ 17˚

Height Range: maximum 4.33 inch (110.0 mm)

110.0 mm

First, remove the locking pin.

Ergonomic

It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees.

5

Connecting the Display

Using the Pivot function

-The pivot function allows you to rotate the screen 90 degrees clockwise.

1 .

Lift the monitor to its highest height to utilize the Pivot function.

2

.

Landscape & Portrait : You can rotate the panel 90 o clockwise.

Please be cautious and avoid contact between the monitor head and the

Stand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack.

Head section

Stand section

3 .

Be careful with the cables when rotating the screen.

6

Connecting the Display

Connecting to the Computer

1.

Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off.

A Connect D-SUB(RGB Analog) Cable (PC)

Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure.

signal input cables

Wall-outlet type

OR When using a D-Sub signal input cable connector for Macintosh

Wall-outlet type

Mac adapter : For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) Dsub VGA connector on the supplied cable to a 15 pin 2 row connector.

NOTE

This is a simplified representation of the rear view.

This rear view represents a general model; your display may differ from the view as shown.

When connecting the D-SUB cable with the LAN cable, connect the D-SUB cable first. Then, connect the LAN cable and other signal input cables.

2.

Press button on the front switch panel to turn the power on. When monitor power is turned on, the

'Self Image Setting Function' is executed automatically on D-SUB input.

NOTE

‘ Self Image Setting Function’? This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for D-SUB input signals.

‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution.

777

Connecting the Display

Connecting to the Computer Using LAN

1.

Make sure to turn off the computer and product. Connect the cable as below sketch map

A

B

Connect peripheral devices

Connect LAN Cable USB 1.1 port

(Only for keyboard and mouse)

USB 2.0 port

(Only for USB memory stick)

Wall-outlet type

OR signal input cables

Host

Wall-outlet type switch hub

LAN Cable Type

- Standard : IEEE 802.3 ETHERNET

ISP

(Internet Service Provider)

Network Monitor

Keyboard/Mouse Input

LAN cable should be connected before booting PC.(This item must be purchased separately.)

Headphone/Earphone Input

Automatically mutes the speaker volume when the headphones are plugged in.

NOTE

For an angle plug earphone/microphone, it is difficult connect it with a peripheral device, so use a straight type.

Angle type Straight type

Connect the USB extension cable to the USB 2.0 port for more convenient use.

When connecting the D-SUB cable with the LAN cable, connect the D-SUB cable first. Then, connect the LAN cable and other signal input cables.

2.

Press button on the front switch panel to turn the power on.

NOTE

When you use the monitor speaker via the LAN, turn the PC volume up to the highest level and adjust the monitor volume.

‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or titled screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution.

8

Connecting the Display

Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off.

Positioning your display

Using the cable holder

1

2

9

3

Control Panel Functions

Front Panel Controls

MUTE Button

• LAN : This menu is available, use this button to switch the sound on or off.

or

<mute off>

• D-SUB : This menu is not available.

<mute on>

MENU Button

Use this button to enter or exit the On Screen Display.

OSD LOCKED/UNLOCKED

This function allows you to lock the current control settings, so that they cannot be inadvertently changed.

Press and hold the MENU button for several seconds.

The message "OSD LOCKED" should appear.

You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message

"OSD UNLOCKED" should appear.

10

Control Panel Functions

( )

SOURCE

( )

VOLUME

Use these buttons to select or adjust functions in the

On Screen Display.

Use this button to make either D-SUB or LAN connector active. This feature is used when two input sources are connected to the display.

Use these buttons to select or adjust functions in the On

Screen Display.

Use buttons to decrease or increase the speaker volume on LAN input.

AUTO/SET

Button

Use this button to enter a selection in the On Screen

Display.

AUTO IMAGE ADJUSTMENT

When adjusting your display settings, always press the AUTO/SET button before entering the On Screen

Display(OSD).

Power Button

Power Indicator

• D-SUB : Use this button to turn the display on or off.

• LAN

Monitor OFF: Press the power button and press it again to turn off the power, or wait 10 second.

LAN(Clint) OFF: Press the power button and the AUTO/SET button to turn off the power of LAN input.

ON : Press the power button to turn on the power.

This Indicator lights up blue when the display operates normally(On Mode). If the display is in Sleep

Mode (Energy Saving), this indicator color changes to flicker.

11

On Screen Display (OSD) Control Adjustment

Screen Adjustment

Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen

Display Control system.

A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD.

NOTE

Allow the display to stabilize for at least 30 minutes before making image adjustments.

To make adjustments in the On Screen Display, follow these steps:

MENU AUTO/SET MENU

Press the MENU Button , then the main menu of the OSD appears.

To access a control, use the or Buttons . When the icon you want becomes highlighted, press the AUTO/SET Button .

Use the / Buttons to adjust the image to the desired level. Use the

AUTO/SET Button to select other sub-menu items.

Push the MENU Button once to return to the main menu to select another function. Push the MENU Button twice to exit from the OSD.

12

On Screen Display(OSD) Selection and Adjustment

The following table indicates all the On Screen Display control, adjustment, and setting menus.

D-SUB

LAN

: D-SUB input

: LAN input

Main menu Sub-menu Supported signals Description

PICTURE BRIGHTNESS

CONTRAST

GAMMA

D-SUB

LAN

To adjust the brightness, contrast and gamma of the screen

COLOR PRESET sRGB

6500K

9300K

D-SUB

LAN

To customize the color of the screen

RED

GREEN

BLUE

POSITION HORIZONTAL

VERTICAL

D-SUB

LAN

To adjust the position of the screen

TRACKING

SETUP

F - ENGINE

CLOCK

PHASE

SHARPNESS

D-SUB

LAN

To improve the clarity and stability of the screen

LANGUAGE

OSD

POSITION

HORIZONTAL

VERTICAL

WHITE BALANCE

POWER INDICATOR

4:3 IN WIDE

ENABLE LAN

FACTORY RESET

D-SUB

LAN

D-SUB

D-SUB

LAN

MOVIE

INTERNET

USER ACE

RCM

D-SUB

D-SUB

LAN

D-SUB

NORMAL

D-SUB

LAN

To customize the screen status for a user's operating environment

To select or customize desired image settings

NOTE

The order of icons may differ depending on the model (13 to 18).

13

On Screen Display(OSD) Selection and Adjustment

You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu.

Press the MENU Button, then the main menu of the OSD appears.

Main Menu

Menu Name

MENU : Exit

: Adjust (Decrease/Increase)

SET : Enter

: Select another sub-menu

: Restart to select sub-menu

Button Tip

Icons

Sub-menus

NOTE

OSD (On Screen Display) menu languages on the monitor may differ from the manual.

14

On Screen Display(OSD) Selection and Adjustment

Sub menu Description Main menu

PICTURE

BRIGHTNESS To adjust the brightness of the screen.

CONTRAST To adjust the contrast of the screen.

GAMMA Set your own gamma value. : -50/0/50

On the monitor, high gamma values display whitish images and low gamma values display blackish images.

MENU : Exit

: Decrease

: Increase

SET : Select another sub-menu

COLOR

PRESET

RED

GREEN

MENU : Exit

: Decrease

: Increase

BLUE

SET : Select another sub-menu

Select the screen color.

• sRGB: Set the screen color to fit the

SRGB standard color specification.

• 6500K: Slightly reddish white.

• 9300K: Slightly bluish white.

Set your own red color levels.

Set your own green color levels.

Set your own blue color levels.

15

On Screen Display(OSD) Selection and Adjustment

Main menu Sub menu Description

POSITION

HORIZONTAL To move image left and right.

VERTICAL To move image up and down.

MENU : Exit

: Decrease

: Increase

SET : Select another sub-menu

TRACKING

MENU : Exit

: Decrease

: Increase

SET : Select another sub-menu

CLOCK

PHASE

To minimize any vertical bars or stripes visible on the screen background.

The horizontal screen size will also change.

To adjust the focus of the display.

This item allows you to remove any horizontal noise and clear or sharpen the image of characters.

SHARPNESS To adjust the clearness of the screen.

16

On Screen Display(OSD) Selection and Adjustment

Main menu

SETUP

Sub menu

LANGUAGE

OSD

POSITION

WHITE

BALANCE

POWER

INDICATOR

4:3 IN WIDE

Description

To choose the language in which the control names are displayed.

To adjust position of the OSD window on the screen.

If the output of the video card is different from the required specifications, the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video card in order to provide the optimal image.

Activate this function when white and black colors are present in the screen.

Use this function to set the power indicator on the front side of the monitor to ON or OFF .

If you set OFF , it will go off.

If you set ON at any time, the power indicator will automatically be turned on.

Use this function to select the image size of the screen.

MENU : Exit

: Adjust

SET

: Adjust

: Select another sub-menu

WIDE 4:3

• WIDE : Switch to full screen mode according to input image signal.

• 4 : 3 : Change the image signal ratio into 4:3.

ENABLE LAN • ON : If you turn on the monitor power, the

LAN input mode is enabled.

• OFF: If you turn on the monitor power, the

RGB input mode is enabled. Even when it is set to OFF , if you press the

SOURCE button, the LAN input mode is enabled.

FACTORY

RESET

Restore all factory default settings except

"LANGUAGE" .

Press the , buttons to reset immediately.

NOTE

If this does not improve the screen image, restore the factory default settings.

If necessary, perform the white balance function again. This function will be enabled only when the input signal is a D-SUB or LAN input signal.

17

On Screen Display(OSD) Selection and Adjustment

Main menu Sub menu Description

MOVIE

INTERNET

This feature lets you easily select the best desired image condition optimized to the environment

(ambient illumination, image types etc).

MOVIE : For animation images in videos or movies

INTERNET : For text images (Word processing etc.)

MENU : Exit

: Decrease

: Increase

SET : Select another sub-menu

USER User

You can manually adjust ACE or RCM.

You can save or restore the adjusted value even when using a different environment.

...

ACE (Adaptive Clarity Enhancer) : Selects the clarity mode.

...

RCM (Real Color Management) : Selects the color mode.

Not applied

Green enhance

Flesh tone

Color Enhance

NORMAL This is under normal operating conditions.

NOTE

It can be only supported the INTERNET and NORMAL features on LAN input.

18

Troubleshooting

Check the following before calling for service.

Is the power cord of the display onnected?

• Check and see if the power cord is connected properly to the power outlet.

● Is the power indicator light on?

Is the power indicator flickering?

• Press the Power button.

• If the display is in power saving mode, try moving the mouse or pressing any key on the keyboard to bring up the screen.

• Try to turn on the PC.

● Do you see an "OUT

OF RANGE" message on the screen?

• This message appears when the signal from the

PC (video card) is out of horizontal or vertical frequency range of the display. See the

'Specifications' section of this manual and configure your display again.

Do you see a "OSD LOCKED" message on the screen?

● Do you see “OSD

LOCKED” when you push MENU button?

• You can secure the current control settings, so that they cannot be inadvertently changed.

You can unlock the OSD controls at any time by pushing the MENU button for several seconds: the message

“OSD UNLOCKED” will appear.

19

Troubleshooting

Display image is incorrect

Display Position is incorrect.

• Press the AUTO/SET button to automatically adjust your display image to the ideal setting.

If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display.

● On the screen background, vertical bars or stripes are visible.

• Press the AUTO/SET button to automatically adjust your display image to the ideal setting.

If the results are unsatisfactory, decrease the vertical bars or stripes using the CLOCK icon in the on screen display.

● Any horizontal noise appearing in any image or characters are not clearly portrayed.

• Press the AUTO/SET button to automatically adjust your display image to the ideal setting.

If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display.

• Check Control Panel --> Display --> Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting. Set the color setting higher than 24 bits

(true color).(Only for D-SUB input)

Important

Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution .

The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer .

If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screen may be dimmed, truncated or biased. Make sure to select the recommend resolution.

20

Troubleshooting

Display image is incorrect

The screen color is mono or abnormal.

• Check if the signal cable is properly connected and use a screwdriver to fasten if necessary.

• Make sure the video card is properly inserted in the slot.

• Set the color setting higher than 24 bits (true color) at Control Panel - Settings .

- “White Balance” is performed on black/white pattern.

- Check if the screen is set to normal mode.

● The screen blinks.

• Check if the screen is set to interlace mode and if yes, change it to the recommend resolution.

- Check if the screen is set to normal mode.

21

Specifications

Display

Sync Input

Video Input

Resolution

Plug&Play

Power

Consumption

Dimensions

& Weight

Tilt Range

Power Input

AC-DC Adapter

Environmental

Conditions

Stand Base

Power cord

55.9 cm (21.9 inch) Flat Panel Active matrix-TFT LCD, Anti-

Glare coating

Visible diagonal size: 55.9 cm

0.282 mm x 0.282 mm pixel pitch

Horizontal Freq.

30 kHz to 66 kHz (Automatic)

Vertical Freq. 57 Hz to 63 Hz (Automatic)

D-SUB Signal Input 15 pin D-SUB Connector

Input Form RGB Analog (0.7 Vp-p/ 75 ohm)

LAN Signal Input LAN Connector

Input Form LAN Signal

Max

Recommend

VESA 1680 x 1050 @ 60 Hz

VESA 1680 x 1050 @ 60 Hz

DDC 2B (Only for D-SUB Input)

On Mode

Sleep Mode

Off Mode

: 29 W (Typ.)

5 W (LAN) / 1 W (D-SUB)

1 W

With Stand

Width 51.57 cm ( 20.30 inch)

Without Stand

51.57 cm ( 20.30 inch)

Height 42.32 cm ( 16.66 inch) ( Min .) 34.46 cm ( 13.57 inch)

53.32 cm( 20.99 inch) ( Max .)

Depth 24.16 cm ( 9.51 inch)

Net 5.3 kg (11.78 lb)

5.91 cm ( 2.32 inch)

Tilt

19 V 3.0 A

-6˚ to 17˚

Type PA-1650-68,manufactured by LITEON TECHNOLOGY CORP.

Operating Conditions

Temperature 10 ˚C to 35 ˚C

Humidity 10 % to 80 % non-Condensing

Storage Conditions

Temperature -20 ˚C to 60 ˚C

Humidity 5 % to 90 % non-Condensing

Attached ( ), Detached ( O )

Wall-outlet type

NOTE

Information in this document is subject to change without notice.

22

Specifications

Preset Modes (Resolution)

- D-SUB (Analog)

Display Modes (Resolution)

5

6

*7

3

4

1

2

640 x 480

720 x 400

800 x 600

1024 x 768

1440 x 900

1680 x 1050

1680 x 1050

Horizontal Freq. (kHz)

31.469

31.468

37.879

48.363

55.935

64.674

65.290

Vertical Freq. (Hz)

60

70

60

60

60

60

60

*Recommend Mode

LAN Preset Modes (Resolution)

Display Modes (Resolution)

3

4

1

2

800 x 600 (60 Hz)

1024 x 768 (60 Hz)

1440 x 900 (60 Hz)

1680 x 1050 (60 Hz)

NOTE

If you access the host PC in LAN input mode, you can adjust the resolution by rightclicking on your desktop, selecting Properties and selecting the Settings tab in the

Display Properties window. However, any resolution other than " LAN Preset Modes

(Resolution) " is not supported.

Indicator

MODE

On Mode

Sleep Mode

Off Mode

LED Color

Blue

Flicker

Off

23

Installing the Wall mount plate

This monitor satisfies the specifications of the Wall mount plate or the interchange device.

1

.

Place the monitor with its front facing downward on a soft cloth.

2

.

Separate the stand after firstly separating 4 screws by using a driver as figure.

24

Installing the Wall mount plate

3.

Install the Wall mount plate.

Wall mount plate(Separate purchase)

This is stand-type or wall mount type and is connectable with Wall mount plate.

Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased.LG recommends that wall mounting be performed by a qualified professional installer.

Wall Mount pad

<Screw Mounting Interface Dimension>

Hole spacing : 75 mm x 75 mm.

Kensington Security Slot

Connected to a locking cable that can be purchased separately at most computer stores.

NOTE

VESA compatible only with respect to screw mounting interface dimensions and mounting screw specifications

Please use VESA standard as below.

* 784.8 mm and under (30.9 inch)

- Wall Mount Pad Thickness : 2.6 mm

- Screw : 4.0 mm x Pitch 0.7 mm x Length 10 mm

* 787.4 mm and above (31.0 inch)

- Please use VESA standard wall mount pad and screws.

25

Make sure to read the Safety Precautions before using the product.

Keep the OWNER’S MANUAL(CD) in an accessible place for furture reference.

The model and serial number of the SET is located on the back or one side of the SET.

Record it below should you ever need service.

MODEL

SERIAL

With LGE Net work Monitor, some PC programs may not be compatible or need to be modified due to different kind of operation.

Please check the compatibility in advance, before purchasing or installing the software.

LGE do not have any kind of legal liability on this matter.

advertisement

Related manuals