Handicare TROPHY Service manual

The Handicare TROPHY is a highly customizable electric scooter designed to provide mobility and independence to those in need. Its advanced features and robust construction make it an ideal choice for both indoor and outdoor use, offering a comfortable and reliable ride experience. With its compact size and maneuverability, the TROPHY can easily navigate tight spaces and uneven terrain, making it suitable for various environments.
PDF Download
Document
SERVICE MANUAL
TROPHY
EN
2 |
Trophy
&copy; 2011 Handicare
All rights reserved.
The information provided herein may not be reproduced and/or published in any form, by print, photo print, microfilm or any other
means whatsoever (electronically or mechanically) without the prior written authorisation of Handicare.
The information provided is based on general data concerning the constructions known at the time of the publication of this
manual. Handicare executes a policy of continuous improvement and reserves the right to changes and modifications.
The information provided is valid for the product in its standard version. Handicare cannot be held liable for possible damage
resulting from specifications of the product deviating from the standard configuration.
The available information has been prepared with all possible diligence, but Handicare cannot be held liable for possible errors in
the information or the consequences thereof.
Handicare accepts no liability for loss resulting from work executed by third parties.
Names, trade names, etc. used by Handicare may not, as per the legislation concerning the protection of trade names, be
considered as being available.
Trophy
| 3
1
Introduction Service manual Trophy ..................................................................................................................... 5
1.1 This manual
5
1.2 Identification of the product
5
1.3 Symbols used in this manual
6
2
Safety ................................................................................................................................................................... 7
2.1 Personnel qualification
7
2.2 Identification on the product
7
2.3 Temperature
7
2.4 Electromagnetic radiation and interference
7
2.5 Markings on the scooter
8
2.6 Technical specifications
8
2.7 Modifications / Adaptations
8
3
Tools ..................................................................................................................................................................... 9
3.1 Tools
9
4
Spare parts ......................................................................................................................................................... 10
4.1 Use of the parts lists
10
4.2 Overview exploded views
11
01 Front frame, front fork and front wheel Trophy 3W
12
02 Front frame, front suspension and front wheels Trophy 4W
13
03 Rear frame, drive unit and rear wheels
14
04 Steering column, mirror and basket
16
05a Console, printed circuit board and throttle control for original electronics (ID-no &lt; QT02400)
17
05b Console, printed circuit board and throttle control for advanced electronics (ID-no &gt; QT02400)
19
06a Wiring, electronics and batteries for original electronics (ID-no &lt; QT02400)
20
06b Wiring, electronics and batteries for advanced electronics (ID-no &gt; QT02400)
21
07 Seat and seat post
22
08 Covers Trophy 3W
23
09 Covers Trophy 4W
25
10a Cabling for original electronics (ID-no &lt; QT02400)
27
10b Cabling for advanced electronics (ID-no &gt; QT02400)
28
4,3 Options
29
5
Service instructions ............................................................................................................................................ 31
5.1 Maintenance plan
31
5.2 Batteries
32
5.3 Tyres
33
5.4 Assembly, replacement and adjustment instructions
33
5.4.1 Console
34
5.4.2 Front frame 3W
38
5.4.3 Front frame 4W
40
5.4.4 Rear frame
46
5.4.5 Electronics
62
5.4.6 Accessories
63
5.4.7 Upgrade instructions controllers
69
5.5 Display menu settings
72
6
Troubleshooting .................................................................................................................................................. 75
7
Technical product information............................................................................................................................. 77
7.1 CE Declaration and standards
77
7.2 Technical specifications
77
7.3 Driving programs
78
7.4 Controller settings PG Drives Egis
79
7.5 Controller settings PG Drives S-Drive 120A
80
4 |
Trophy
7.6
7.7
7.8
7.9
8
Controller settings PG Drives S-Drive 140A
Electrical diagram Trophy Egis
Electrical diagram Trophy S-Drive
Service information transaxles
82
90
91
93
Warranty ............................................................................................................................................................. 94
8.1 Definitions of terms
94
8.2 Warranty period table
94
Trophy
1
Introduction Service manual Trophy | 5
Introduction Service manual Trophy
1.1 This manual
This manual contains the instructions for repairs and general maintenance of the Trophy Scooter.
Mechanics who do repairs on this scooter must be well trained and familiar with the repair methods and the maintenance of the
Trophy scooter.
Always make sure that the work is carried out safely, particularly with respect to procedures requiring the scooter to be lifted up.
We advise that you contact our service department before doing repair work on a scooter that has been involved in an accident.
The following specifications are important when ordering parts:
• Model
• Year of manufacture
• Colour
• ID-number
• Part number
• Name of the part concerned
This information is provided on the identification plate. See 'Identification of the product'.
Available documentation
The following technical documentation is available / required to service this scooter:
• User manual
• Service manual
Service and technical support
For information concerning specific settings, maintenance or repair works please contact the Handicare Customer Service
department. They are always prepared to help you. Ensure you have at hand:
• Model
• Year of manufacture
• ID-number
1.2 Identification of the product
HANDICARE B.V.
VOSSENBEEMD 104
5705 CL HELMOND
THE NETHERLANDS
A
B
F
C
TYPE/TYPE/TYP:
YEAR/JAAR/JAHR:
IDNR.:
USAGE:
GEBRUIKSGEBIED:
GEBRAUCHSGEBIET:
MAX.LOAD/MAX.BELASTB./ZUL.GESAMTGEW.:
D
The identification plate contains the following data:
A.
Model
B.
Year of manufacture
C.
ID-number
D.
Usage: indoor, outdoor or both
E.
Maximum load in kg
F.
Manufactures address
E
See for the location of the identification plate &acute;markings on the scooter&acute;.
6 | Introduction Service manual Trophy
1.3 Symbols used in this manual
Note!
Pointing out possible problems to the user of this manual.
Caution!
Advice for the user of this manual to prevent damage to the product.
Warning!
Warnings for the user of this manual to prevent personal in jury.
Not following these instructions may result in physical injury, damage to the product or damage to the environment!
Reference symbol
When necessary this service manual refers to other manuals as shown below:
 Battery charger: refers to the user manual of the battery charger
 Scooter: refers to the general user manual of the Trophy
Trophy
Trophy
2
Safety | 7
Safety
2.1 Personnel qualification
Repairs may only be carried out by trained and authorised service technicians.
During the execution of their work, they are at all times fully responsible for the fulfilment of locally applicable safety guidelines
and standards.
Temporary employees and persons in training may only carry out repair and replacement work under the supervision of an
authorised service technician.
2.2 Identification on the product
Safety
Safety information is indicated with the warning symbol.
Warning!
Follow the instructions carefully next to these warning symbols! Not paying careful attention to these instructions could result in
physical injury or damage to the scooter or the environment. Wherever possible, safety information is also provided in this manual
in the relevant chapter.
2.3 Temperature
Warning!
Avoid physical contact with the scooter’s motor. The motor is continuously in motion during use and can reach high temperatures.
After use, the motor will cool down slowly. Physical contact may cause burns.
Ensure that the scooter is not exposed to direct sunlight for extended periods of time. Certain parts of the scooter, such as the
seat, the backrest, the armrests and the steering device become hot if exposed to the sun for too long. This may cause burns or
skin irritation.
2.4 Electromagnetic radiation and interference
The scooter has been tested for compliance with the applicable requirements regarding electromagnetic radiation (EMC
requirements).
The Trophy’s immunity level is 20 volt/metre.
Note!
It cannot be excluded that electromagnetic radiation emanating from mobile telephones, medical apparatus and other sources,
may have an influence on the scooter.
It cannot be excluded that the scooter will interfere with the electromagnetic fields of, for example, shop doors, burglar alarm
systems and/or garage door openers.
In the unlikely event that such problems do occur, you are requested to notify your dealer immediately.
Powered wheelchairs and scooters can be affected by sources of radio waves, such as radio and TV transmitters, amateur radio
stations, lifts, transmitting equipment, stereo radios and mobile telephones If the scooter’s electronics are not well shielded,
sensitive electrical devices, such as shop alarm systems and garage door openers, can be affected. The scooter has been tested
for such interference. Please report any problems of this nature to your dealer immediately.
The following advices are intended to prevent the electric scooter from being driven unintentionally, which could lead to serious
injury.
1. Do not turn on any manually controlled equipment for personal communication, such as a radio transmitter or mobile
telephone, while the electric scooter is switched on.
2. Keep at a distance from transmitter equipment, such as radio and TV stations.
3. If the scooter starts making unintended movements, or if the brake goes into freewheel / neutral mode, turn off the powered
wheelchair or scooter by removing the ignition key from the lock.
4. Be aware of the fact that any accessories, components or adaptations installed on the scooter may increase the effect of radio
waves.
Note:
There is no easy way of testing the effects of radio waves on the general immunity of powered wheelchairs or scooters.
5. All cases of unintended movements of the scooter spontaneously going into freewheel / neutral mode should be reported to
your dealer or to the scooter manufacturer. When reporting, please indicate whether a source of radio waves was nearby at
the time.
8 | Safety
Trophy
2.5 Markings on the scooter
Never remove or cover up the markings, symbols and instructions affixed to the scooter. These safety measures must remain
present and clearly legible throughout the entire lifestam of the scooter.
Replace or repair any markings, symbols or instructions that have become illegible or damaged immediately. Please contact your
dealer for assistance.
Product labels
The following sticker/label can be found on the product:
A1
A2
B.
C.
D.
Free wheel Trophy Alpine (and models &lt; 2012)
Free wheel Trophy (if not A1)
Identification plate
Tyre pressure front wheel(s)
Tyre pressure rear wheels
A. Freewheel handle position
1. DRIVE mode: Lever fully upper position: Motor brake applied, scooter can not be pushed
2. FREEWHEEL / NEUTRAL mode: Lever lowest position: Motor brake not applied. Scooter can be pushed manually
when electronics are off.
B. Identification plate
HANDICARE B.V.
VOSSENBEEMD 104
5705 CL HELMOND
THE NETHERLANDS
A
B
F
C
TYPE/TYPE/TYP:
YEAR/JAAR/JAHR:
IDNR.:
USAGE:
GEBRUIKSGEBIED:
A.
B.
C.
D.
E.
F.
Model
Year of manufacture
ID-number
Usage: indoor, outdoor or both
Maximum load in kg
Manufactures address
GEBRAUCHSGEBIET:
MAX.LOAD/MAX.BELASTB./ZUL.GESAMTGEW.:
D
E
C. Instruction for transportation ( Scooter)
Warning!
The scooter is not intended to be used as seat in motor vehicle.
2.6 Technical specifications
No changes may be made to the technical specifications.
2.7 Modifications / Adaptations
Modifications, not executed by Handicare, to components and electronics of this product are not permitted.
Trophy
3
Tools | 9
Tools
3.1 Tools
The tools below are needed for various mechanical settings and maintenance:
Quantity
1
1
1
1
1
1
1
1
1
1
1
1
Description
Screwdriver, medium
Screwdriver, crosshead
Hammer (plastic)
Chaser
Circlip pliers
Ring spanner
Torque wrench
Socket
Socket bit
Allen key
Loctite
Shock absorber adjustment key
Size (mm)
5
7 / 10 / 11 / 13 / 17
7 / 8 / 10 / 11 / 12 / 13 / 16 / 17
6
3/4/5/6/8
243
-
Use only high-quality tools for the adjustment(s) described.
Make sure that the hexagon of the spanner is attached securely to the hexagon of the fastening article. This prevents the 'rotation'
of hexagons of fastening articles and spanners that may affect proper adjustment.
The following tools are needed for various electronic settings:
Quantity
Description
Function
1
PG - pc programmer
B-version
Adaptation of the drive programs and technical settings.
Reading out the fault history
1
PG - programmer unit
SPIB handheld
Alternative device for PC. Adaptation of the drive programs
and technical settings.
Reading out the fault history
PR0210
10237
10 | Spare parts
4
Trophy
Spare parts
4.1 Use of the parts lists
This document is meant as a reference book to be used to order parts for the scooter that is shown on the front cover.
How to order
When ordering parts, please specify:
• ID-number (see the identification plate)
• Group (to which the relevant part belongs)
• Article number
• Number of parts required
• Description (in the relevant language)
• Dimensions (if applicable)
Remark
• If a part does not have a position number, it means that the part concerned cannot be purchased separately. The part concerned is
part of the assembly shown. This assembly must be ordered as one piece. It has to be replaced in its entirety.
• Boxed position numbers refer to the relevant drawing.
Order address
Please mail or fax your orders to your supplier.
Service technicians
Repairs may only be carried out by trained and authorised service technicians. During the execution of their work they are at all times
fully responsible for the fulfilment of locally applicable safety guidelines and standards.
Temporary employees and persons in training may only carry out repair and replacement work under the supervision of an authorised
service technician.
Trophy
Spare parts | 11
4.2 Overview exploded views
Pos
01
02
03
04
05a
05b
06a
06b
07
08
09
10a
10b
Description
Front frame, front fork and front wheel Trophy 3W
Front frame, front suspension and front wheels Trophy 4W
Rear frame, drive unit and rear wheels
Steering column, mirror and basket
Console, printed circuit board and throttle control for original electronics (ID-no &lt; QT02400)
Console, printed circuit board and throttle control for advanced electronics (ID-no &gt; QT02400)
Wiring, electronics and batteries for original electronics (ID-no &lt; QT02400)
Wiring, electronics and batteries for advanced electronics (ID-no &gt; QT02400)
Seat and seat post
Covers Trophy 3W
Covers Trophy 4W
Cabling for original electronics (ID-no &lt; QT02400)
Cabling for advanced electronics (ID-no &gt; QT02400)
Options
Page
12
13
14
16
17
19
21
22
23
24
25
26
27
28
12 | Spare parts
Trophy
01 Front frame, front fork and front wheel Trophy 3W
1
2
4
DEF
DE
Pos
1
2
3
4
5
6
7
7
8
9
10
11
12
13
14
15
16
17
18
19
20a
20b
20c
21a
21b
22
23
24
25
26
-
Qty
1
1
2
1
1
2
1
1
2
2
14
1
2
2
1
1
1
2
1
2
1
1
1
1
1
1
1
2
1
1
2
2
Article number
9003907
9004025
00001.0008
9005156
9000762
00000.1701
9000178
9000871
9000630
9000591
9000788
1010286
1001277
00000.5306
00001.0804
1001796
00000.6008
9000632
9000542
00000.3218
9001994
9004159
1015112
1015113
1015118
9002166
00000.2203
00000.1702
9000504
9000493
00000.5500
8
Description
Nylon bearing seat post
Seat post
Spacer block, battery
Seat post bolt
Lever freewheel
Lock nut M6
Freewheel mechanism for Schmid transaxle
Hand brake mechanism
Tulle
Strap, battery retention
Clamp, cable
Front frame, incl. ball-head bearings Trophy 3W
Anti-slip mat
Bearing bush 14x16x4 Iglidur
Rolled pin 6x30
Lock washer
Ring 20x28x1
Bush bearing tiller
Horn for original electronics (ID-no &lt; QT02400)
Screw M4x12
Front wheel complete with white rim and grey tyre, no longer available
Front wheel complete with grey rim and grey tyre
Front wheel complete with grey rim and black tyre
Outer tyre 12 1/2 x 2 1/4 grey block profile
Outer tyre 12 1/2 x 2 1/4 black block profile
Inner tube 12 1/2 x 2 1/4
Hex bolt M8x150
Spring washer M8
Lock nut M8
Front fork, complete
Ball-head bearing 6004 2NSE
Ball bearing 6002 2NSL
Trophy
Spare parts | 13
02 Front frame, front suspension and front wheels Trophy 4W
3
18a,b
19a,b
20
6
7
9
2
2
3
9
6
23
9
10
8
2
9
16
Pos
1
2
3
3
4
5
6
7
7
8
9
10
11
12
13
14
14
15
15
16
17
18a
18b
19a
19b
20
21
22
23
-
Qty
1
4
2
2
2
1
2
2
2
1
4
2
2
1
8
1
1
1
1
2
1
2
2
2
2
2
2
2
4
2
Article number
1010287
00000.1703
9002090
9004458
00000.3218
9000542
9001641
9002091
9004459
9001895
001.03010.001
9001803
9002101
9001802
00000.1702
9001795
9003406
9001801
9003408
00000.4307
9001940
9001815
9004511
1015112
1015113
1015118
9002006
9002155
00000.1702
9000493
18a,b
19a,b
20
Description
Front frame, incl. ball-head bearings Trophy 4W
Lock nut M10 D985
Swing arm top assy (grey)
Swing arm top assy (black)
Screw M4x12
Horn for original electronics (ID-no &lt; QT02400)
Shock absorber
Swing arm low assy (grey)
Swing arm low assy (black)
Connection plate
Hex bolt M10x40 D931
Axle suspension parallel bracket
Steer rod
Steer shaft
Lock nut M8
Wheel bracket left (grey)
Wheel bracket left (black)
Wheel bracket right (grey)
Wheel bracket right (black)
Hex bolt M6x12
Bumper plate Trophy 4-wiel
Front wheel complete with grey rim and grey tyre, Trophy 4W
Front wheel complete with grey rim and black tyre, Trophy 4W
Outer tyre 12 1/2 x 2 1/4 grey block profile
Outer tyre 12 1/2 x 2 1/4 black block profile
Inner tube 12 1/2 x 2 1/4
Cover grey
Tensilock bolt Precote 85 M8x12
Lock nut M8
Ball-head bearing 6004 2NSE
7
14 | Spare parts
Trophy
03 Rear frame, drive unit and rear wheels
11/12
13 14 15 16 17 18
26
19
2
1
4
20
19
22
21
9a,b,c,d / 10
7a,b,c,d,e
8a,b,c,d,e
3
22
16
23
27
28
4
24
25
29
30
9a,b,c,d / 10
Pos
1
1
1
2
2
2
2
3
3
4
5a
5b
5c
5d
5e
6a
6b
6c
6d
6e
7a
7b
7c
7d
7e
8a
8b
Qty
4
4
1
4
1
1
1
1
4
4
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Article number
1002646
103.00031.000
1011585
51035
1007947
1007961
1008565
1013184
00000.1703
1013185
1012527
9000550
9001996
1015104
9007719
9007723
9001172
9001998
1015154
9007717
9007721
9000549
9001995
1015103
9007720
9007724
1
1
9001173
9001997
5a,b,c,d,e
6a,b,c,d,e
11/12
Description
Carbon brush for Trophy with Egis (8x10 mm)
Carbon brush for Trophy with S-Drive (8x12 mm)
Carbon bruch set for CT transaxle (10x18 mm)
Carbon brush screw cap for Schmid transaxle
Transaxle Schmid Trophy 3 and 4-wheel, Egis
Transaxle Trophy Alpine, Egis (max. 11 km/h)
Transaxle Trophy Alpine, S-Drive (max. 11 km/h)
Transaxle CT Trophy 3 and 4-wheel, S-Drive
Lock nut M10 D985
Lock nut low M10 D985
Hex. flange bolt M12x30 (torque 90Nm, use locktite 243)
Rear wheel left side with brake drum, white rim and grey tyre
Rear wheel left side with brake drum, grey rim and grey tyre
Rear wheel left side with brake drum, grey rim and grey tyre with block profile
Rear wheel left side with brake drum, grey rim and black tyre
Rear wheel left side with brake drum, grey rim and black tyre with block profile
Rear wheel left side standard, white rim and grey tyre
Rear wheel left side standard, grey rim and grey tyre
Rear wheel standard, grey rim and grey tyre with block profile
Rear wheel left side standard, grey rim and black tyre
Rear wheel left side standard, grey rim and black tyre with block profile
Rear wheel right side with brake drum, white rim and grey tyre
Rear wheel right side with brake drum, grey rim and grey tyre
Rear wheel right side with brake drum, grey rim and grey tyre with block profile
Rear wheel right side with brake drum, grey rim and black tyre
Rear wheel right side with brake drum, grey rim and black tyre with block
profile
Rear wheel right side standard, white rim and grey tyre
Rear wheel right side standard, grey rim and grey tyre
Trophy
Spare parts | 15
Continued from 03 Rear frame, drive unit and rear wheels
Pos
8c
8d
8e
9a
9b
9c
9d
10
11
12
13
14
15
16
17
17
18
19
20
21
22
23
24
25
26
27
28
29
30
-
Qty
1
1
1
2
2
2
2
2
2
2
1
1
1
2
1
1
1
4
1
1
2
1
1
2
2
2
2
2
2
1
1
1
1
1
1
2
2
1
1
1
Article number
1015154
9007718
9007722
1015114
1015102
9007716
9007725
1015119
1004272
9002006
9000821
9000642
00000.4009
00000.1703
9000603
9000683
1002243
00000.4307
9000256
9000257
9000689
1002242
9000494
1353
103.00091.000
00000.3715
9002221
00000.2003
00000.1702
1003225
9003243
1012104
1003209
1002576
1002577
9001171
9000551
1012106
1015444
1001817
Description
Rear wheel standard, grey rim and grey tyre with block profile
Rear wheel right side standard, grey rim and black tyre
Rear wheel right side standard, grey rim and black tyre with block profile
Outer tyre 3.00x10 grey with highway profile
Tyre grey with block profile rear wheel Trophy
Tyre black rear wheel Trophy
Tyre black with block profile rear wheel Trophy
Inner tube 3.00x10
Cover white
Cover grey
Magnet plate, speed sensor
Speed sensor magnet
Allen bolt M8x35
Lock nut M10 D985
Rear spring, standard (black)
Rear spring, heavy duty (black with orange sticker, previously chrome)
Allen bolt M10x75
Hex bolt M6x12
Mounting bracket, right mud guard
Mounting bracket, left mud guard
Rubber mounting strip, transaxle
Allen bolt M10x40
Back frame
Hinge bush M8
Wedge for Schmid transaxle
Buttonhead M8x30 ISO7380
Washer M8x30x1,5
Washer M8 DIN125A-VZ
Lock nut M8 DIN985/8/VZ
Motor brake, Egis
Motor brake, S-Drive
Motor brake for CT transaxle
Friction disk for motorbrake
Brake right for hand brake
Brake left for hand brake
Wheel hub standard
Wheel hub with drum brake
Freewheel lever for CT transaxle
Motorbrake cover Schmid
Hand brake
16 | Spare parts
Trophy
04 Steering column, mirror and basket
16 17 18 19
20 21 22
15
3
8
2 1
4
9
14
13
5
7
11
10
12
6
11
10
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Qty
1
1
1
1
1
1
1
1
1
2
2
1
2
1
1
2
2
1
2
1
1
1
Article number
00000.4041
00000.2203
9000019
9000648
9000781
00001.0804
9001095
1008573
9000610
9000826
00000.1701
9000684
9008687
9000435
9001135
00000.4307
00000.2202
9000732
00000.3612
9000704
1010832
9000601
Description
Allen bolt M8x55
Spring washer M8
Spacing bush
Handle, steering adjustment
Cap, steering adjustment handle
Rolled pin 6x30
Steering column adjustment tube
Nylon bushing, steering column
Control cable, gas spring for steering adjustment
Shoulder bolt, gas spring
Lock nut M6
Gas spring, steering adjustment inc. operating mechanism
Hex bolt Precote 85 M8x25
Cylinder, steering column
Basket, front side (max. load 5 kg)
Hex bolt M6x12
Spring washer M6
Support
Screw M4x10
Basket holder
Mirror, black (left side)
Cover plate, steering adjustment
Trophy
Spare parts | 17
05a Console, printed circuit board and throttle control for original electronics (ID-no &lt; QT02400)
14
13
1
15
2
3
12
10
5
4
7
9
11
16
6
10
9
8
17
Pos Pos Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
3
4
5
1
6
1
7
3
8
1
9
2
10
2
11
1
12
1
12
1
13
1
13
1
13
1
13
1
14
2
14
2
Article
Qtynumber
ArticleDescription
number Description
1008345
Steering wheel with throttle left Egis
1008342
Revision steering wheel with throttle left Egis
1008346
Steering wheel with throttle right Egis
1008343
Revision steering wheel with throttle right Egis
1008347
Steering wheel with dual throttle Egis
1008344
Revision steering wheel with dual throttle Egis
1008603
Steering wheel with throttle left S-Drive
9002671
Revision steering wheel with throttle left S-Drive
1008604
Steering wheel with throttle right S-Drive
9002672
Revision steering wheel with throttle right S-Drive
1008601
Steering wheel with dual throttle S-Drive
9002673
Revision steering wheel with dual throttle S-Drive
1008055
Potentiometer, accelerator
00000.3307
Sheet-metal screw 2,9x13
1001341
Knob, speed potentiometer
1002555
Console, upper (standard) for original electronics (ID-no &lt; QT02400)
9002792
Screw Ejot K30x6
9000481
Console, lower
9000531
Cable, indicator switch
9000522
Indicator switch for original electronics (ID-no &lt; QT02400)
9000496
PCB, console for original electronics (ID-no &lt; QT02400)
9002182
Speed potentiometer Egis for original electronics (ID-no &lt; QT02400)
9006110
Speed potentiometer S-Drive for original electronics (ID-no &lt; QT02400)
9006111
Ignition lock, &gt; 31-10-2011 for original electronics (ID-no &lt; QT02400)
9002188
Harness for ignition lock Egis for original electronics (ID-no &lt; QT02400)
9006998
Ignition lock / tiller cover bottom, replacement set, Trophy &lt; 01-11-2011
9006999
Ignition lock / tiller cover bottom with switch hole, replacement set, Trophy &lt; 01-11-2011
1008307
Ignition key for original electronics (ID-no &lt; QT02400)
1002571
Ignition key (Old type A126)
18 | Spare parts
Trophy
Continued from 05a Console, printed circuit board and throttle control for original electronics (ID-no &lt; QT02400)
Pos
14
15
16
17
-
Qty
2
4
2
4
2
Article number
9005810
9002104
9002177
1002343
9001230
Description
Ignition key &gt; 31-10-2011
Spacer 3.2x5.5x2.2
Throttle control dummy
Screw Ejot K40x12
Cover steering wheel
Trophy
Spare parts | 19
05b Console, printed circuit board and throttle control for advanced electronics (ID-no &gt; QT02400)
24
1
25
5
4
21
4
20
6
22
12
7
7
22
23
3
17
23
3
18
7
19
3
2
3
11
26
10
8
21
21
14 13
19
19
19
10
19
26
27
19
Pos
1
2
3
4
5
6
6
7
8
10
11
11
11
12
13
14
17
18
19
20
21
22
23
24
25
26
27
28
-
Qty
1
1
4
2
1
1
1
3
1
2
1
1
1
1
1
1
1
1
7
1
3
2
2
1
1
2
1
1
1
1
1
Article number
9004185
1008055
00000.3307
9004641
1012536
9007568
1012535
9002792
9007223
9004435
9008789
9008791
9008790
9004438
9004432
9005810
9007423
9004302
9005802
9004301
00000.3200
9004331
00000.3719
9006138
9000904
9004303
9006980
1016535
1016928
1016930
1016929
19
Description
Steering wheel
Potentiomet accelerator
Sheet-metal screw 2,9x13
Throttle harness
Assy Dashboard speed knob
Assy Top Standard for advanced electronics (ID-no &gt; QT02400)
Assy Top Full option for advanced electronics (ID-no &gt; QT02400)
Screw Ejot K30x6
Console Bottom
Indicator switch for advanced electronics (ID-no &gt; QT02400)
Tiller PCB Basic for advanced electronics (ID-no &gt; QT02400)
Tiller PCB Dual Control for advanced electronics (ID-no &gt; QT02400)
Tiller PCB Full Option for advanced electronics (ID-no &gt; QT02400)
Speed switch for advanced electronics (ID-no &gt; QT02400)
Ignition switch for advanced electronics (ID-no &gt; QT02400)
Ignition key for advanced electronics (ID-no &gt; QT02400)
Cover steering wheel
Steering wheel cover bottom
Srew Ejot K40x12
Steering wheel cover top
Recessed buttonhead screw M5x12
Cover brake position
Buttonhead screw M5x10
Emergency stop button
Emergency stop button dummy
Cover for indicator switch
Cover Steering Console
Full option steering wheel for advanced electronics (ID-no &gt; QT02400)
Replacement set Basic
Replacement set Dual control
Replacement set Full options
20 | Spare parts
Trophy
06a Wiring, electronics and batteries for original electronics (ID-no &lt; QT02400)
2
1
3
4
5
7
6
1
2
3
8
4
10
9
Pos
1-4
5
6
6
6
7
8
9
10
10
Qty
2
4
1
1
1
1
1
1
2
2
Article number
1009814
00000.3204
1008074
9002457
1012504
1002558
9000647
9000782
9002759
9002761
Description
Replacement Set 2 LED rear lights
Screw M5x25
Controller, Egis 110A
Controller S-Drive 120A (from serial number LT03210) (11-09-2008)
Controller S-Drive 140A (from serial number PT01331) (24-03-2011)
Controller interface for original electronics (ID-no &lt; QT02400)
Mounting plate, Electronics (only needed on old frame)
Tulle 32 x 1.6
Battery MK (50Ah C5) (60Ah C20)
Battery MK (72Ah C5) (86Ah C20)
Trophy
Spare parts | 21
06b Wiring, electronics and batteries for advanced electronics (ID-no &gt; QT02400)
1
5
11
7
5
6
1
13
14
12
12
12
10
9
10
Pos
1
5
6
7
9
10
10
11
12
13
14
15
16
Qty
2
2
1
1
1
2
2
2
4
1
1
1
2
Article number
9004503
00000.3204
1012504
9008778
9000782
9002759
9002761
00000.4036
00000.1501
9004433
00000.4322
1012412
9002752
Description
Rear light LED
Screw M5x25
Controller S-Drive 140A
Controller interface for advanced electronics (ID-no &gt; QT02400)
Tulle 32 x 1.6
Battery MK (50Ah C5) (60Ah C20)
Battery MK (72Ah C5) (86Ah C20)
Screw M5x12
Hexagon nut M6
Horn for advanced electronics (ID-no &gt; QT02400)
Hexagon bolt M8x12
Connector cover
Set battery connection covers
22 | Spare parts
Trophy
07 Seat and seat post
2
1
3
4
5
Pos
1
2
3
4
5
-
Qty
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
Article number
118.00221.000
1002861
1003383
118.00231.000
9000034
9000042
1366
1002241
1008392
1002392
232.00011.000
237.00011.000
1001806
1002394
1008411
Description
Armrest, right
Master seat with armrests
Lumbar knob
Armrest, left
Seat frame with slider (right-side operation)
Seat fixation strip
Plastic cover for seat fixation strip
Master seat with seat frame
Master seat comfort (Enschede) with seat frame
Master seat Fabric with seat frame and rain cover
Headrest receiver
Headrest
Height adjustable armrests, stepless (19-33 cm), extra long (40 cm) and soft
Height adjustable armrests, 20 (standard), 22 and 24 cm
Rain cover Master seat
Trophy
Spare parts | 23
08 Covers Trophy 3W
1a,b,c,d,e
2a,b,c,d,e
9a,b,c,d,e
11a,b
12a,b,c,d,e
7
17
Pos
1a
1b
1c
1d
1e
2a
2b
2c
2d
2e
3
4
5
6
7
8
8
8
Qty
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
Article number
1001905
1015765
1015770
1015775
1015780
1007754
1015760
1015761
1015762
1015763
1007757
1007755
1001276
9002229
1009940
9006856
9006997
9006998
8
1
9006999
9a
9b
9c
9d
9e
10
11a
11b
12a
1
1
1
1
1
1
2
2
2
1
1001895
1015766
1015771
1015776
1015781
9000486
9000543
9007552
9002236
1001899
18
Description
Mudguard Red metallic
Mudguard Moonstone blue metallic
Mudguard Sparkling champagne metallic
Mudguard Platinum white metallic
Mudguard Graphite black metallic
Rear cover assy Red metallic
Rear cover assy Moonstone blue metallic
Rear cover assy Sparkling champagne metallic
Rear cover assy Platinum white metallic
Rear cover assy Graphite black metallic
Battery cover assy
Rear bumper assy
Rubber strap, battery cover
Plateau mat
Side skirt assy black, set (replacement set)
Rear cover, steering column black &gt; 31-10-2011
Rear cover, steering column black. with hole for switch &gt; 31-10-2011
Ignition lock / tiller cover bottom, replacement set, Trophy &lt; 01-11-2011
Ignition lock / tiller cover bottom with switch hole, replacement set, Trophy &lt;
01-11-2011
Front cover, steering column Red metallic
Front cover, steering column Moonstone blue metallic
Front cover, steering column Sparkling champagne metallic
Front cover, steering column Platinum white metallic
Front cover, steering column Graphite black metallic
Front cover, front portion
Indicator light 12V for originial electronics (ID-no &lt; QT02400)
Indicator light 24V for advanced electronics (ID-no &gt; QT02400)
Foam ring for indicator
Front cover Red metallic
24 | Spare parts
Trophy
Continued from 08 Covers Trophy 3W
Pos
12b
12c
12d
12e
13
14
14
15
16
17
18
19
-
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
Article number
1015767
1015772
1015777
1015782
9000536
9000535
1010852
1009956
9000485
1009947
1009946
1009941
9000426
1012522
00000.1503
Description
Front cover Moonstone blue metallic
Front cover Sparkling champagne metallic
Front cover Platinum white metallic
Front cover Graphite black metallic
Spherical bulb 24V 21W
Headlight, complete
Headlight, complete (Version 2, from 11-11-2010)
Front bumper Trophy 3W
Front cover, rear portion Trophy 3W
Foot support, right
Foot support, left
Foot support set (replacement set)
Logo Trophy
Logo Handicare
Reflector red round 60 mm
Trophy
Spare parts | 25
09 Covers Trophy 4W
1a,b,c,d,e
2a,b,c,d,e
9a,b,c,d,e
11a,b
12a,b,c,d,e
17a,b,c,d,e
18a,b,c,d,e
Pos
1a
1b
1c
1d
1e
2a
2b
2c
2d
2e
3
4
5
6
7
8
8
8
Qty
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
Article number
1001905
1015765
1015770
1015775
1015780
1007754
1015760
1015761
1015762
1015763
1007757
1007755
1001276
9002230
1009940
9006856
9006997
9006998
8
1
9006999
9a
9b
9c
9d
9e
10
11a
11b
12a
1
1
1
1
1
1
2
2
2
1
1001895
1015766
1015771
1015776
1015781
9000486
9000543
9007552
9002236
1001899
Description
Mudguard Red metallic
Mudguard Moonstone blue metallic
Mudguard Sparkling champagne metallic
Mudguard Platinum white metallic
Mudguard Graphite black metallic
Rear cover assy Red metallic
Rear cover assy Moonstone blue metallic
Rear cover assy Sparkling champagne metallic
Rear cover assy Platinum white metallic
Rear cover assy Graphite black metallic
Battery cover assy
Rear bumper assy
Rubber strap, battery cover
Plateau mat
Side skirt assy black, set (replacement set)
Rear cover, steering column black &gt; 31-10-2011
Rear cover, steering column black. with hole for switch &gt; 31-10-2011
Ignition lock / tiller cover bottom, replacement set, Trophy &lt; 01-11-2011
Ignition lock / tiller cover bottom with switch hole, replacement set, Trophy &lt;
01-11-2011
Front cover, steering column Red metallic
Front cover, steering column Moonstone blue metallic
Front cover, steering column Sparkling champagne metallic
Front cover, steering column Platinum white metallic
Front cover, steering column Graphite black metallic
Front cover, front portion
Indicator light 12V for originial electronics (ID-no &lt; QT02400)
Indicator light 24V for advanced electronics (ID-no &gt; QT02400)
Foam ring for indicator
Front cover Red metallic
26 | Spare parts
Trophy
Continued from 09 Covers Trophy 4W
Pos
12b
12c
12d
12e
13
14
14
15
16
17a
17b
17c
17d
17e
18a
18b
18c
18d
18e
-
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
Article number
1015767
1015772
1015777
1015782
9000536
9000535
1010852
9001970
9001921
9001963
1015768
1015773
1015778
1015783
9001964
1015769
1015774
1015779
1015784
9000426
1012522
00000.1503
Description
Front cover Moonstone blue metallic
Front cover Sparkling champagne metallic
Front cover Platinum white metallic
Front cover Graphite black metallic
Spherical bulb 24V 21W
Headlight, complete
Headlight, complete (Version 2, from 11-11-2010)
Front bumper Trophy 4W
Front cover, rear portion Trophy 4W
Mudgard right hand front Red metallic
Mudgard right hand front Moonstone blue metallic
Mudgard right hand front Sparkling champagne metallic
Mudgard right hand front Platinum white metallic
Mudgard right hand front Graphite black metallic
Mudgard left hand front Red metallic
Mudgard left hand front Moonstone blue metallic
Mudgard left hand front Sparkling champagne metallic
Mudgard left hand front Platinum white metallic
Mudgard left hand front Graphite black metallic
Logo Trophy
Logo Handicare
Reflector red round 60 mm
Trophy
Spare parts | 27
10a Cabling for original electronics (ID-no &lt; QT02400)
1a,b,c
2a,b
3
4a,b
5
6a,b
7a,b
Pos
1a
1b
1c
2a
2b
3
4a
4b
5
6a
6b
7a
7b
-
Qty Article number Description
1
9000783
Power cable complete with charge socket, Egis for original electronics (ID-no &lt; QT02400)
1
9002449
Power cable complete with charge socket and quick release clamps, S-Drive for original
electronics (ID-no &lt; QT02400)
1
9004029
Power cable complete with charge socket and ring lugs, S-Drive
1
9002181
Cable harness, interface/Egis for original electronics (ID-no &lt; QT02400)
1
9002190
Cable harness, interface/Egis for footcontrol for original electronics (ID-no &lt; QT02400)
1
9004431
Speed sensor with cable
1
9000537
Main harness, lighting for original electronics (ID-no &lt; QT02400)
1
9004653
Main harness, lighting for version 2, from 11-11-2010 till original electronics (ID-no &lt; QT02400)
1
99117
Fuse 100A
1
9000526
Battery cable, series connection (incl. terminal clamp) for original electronics (ID-no &lt;
QT02400)
2
9006564
Batterry cable with ring lugs
1
9002180
Main cable Egis for original electronics (ID-no &lt; QT02400)
1
9002460
Main cable S-Drive for original electronics (ID-no &lt; QT02400)
2
9000774
Battery connector red for original electronics (ID-no &lt; QT02400)
2
9000775
Battery connector black for original electronics (ID-no &lt; QT02400)
28 | Spare parts
Trophy
10b Cabling for advanced electronics (ID-no &gt; QT02400)
3
8
1
4
5
6
Pos
1
2
3
4
5
6
7
8
Qty
1
1
1
2
2
2
Article number
9004029
9004431
9004429
99117
9006564
9007367
Description
Power cable complete with charge socket and ring lugs, S-Drive
Speed sensor
Main Harness for advanced electronics (ID-no &gt; QT02400)
Fuse 100A
Batterry cable with ring lugs
Indicator extension harness for advanced electronics (ID-no &gt; QT02400)
Trophy
Spare parts | 29
4,3 Options
1a
1b
1c
1d
1e
1f
2
3
4
5
6
7
8
9
10
11
12
13
Pos
1a-1d
1a-1d
1a-1d
1a-1d
1a-1d
1a-1f
1a-1f
1a-1f
1a-1f
1a-1f
2
3
4
5
6
7
8
Qty
Article number Description
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1017464
1017458
1017459
1017460
1017461
1017463
1017415
1017416
1017417
1017418
1015545
9000620
9000703
4930
1001813
1001814
A810
1001754
2537
1003095
Colour exchange set Red metallic 3W
Colour exchange set Moonstone blue metallic 3W
Colour exchange set Sparkling champagne metallic 3W
Colour exchange set Platinum white metallic 3W
Colour exchange set Graphite black metallic 3W
Colour exchange set Red metallic 4W
Colour exchange set Moonstone blue metallic 4W
Colour exchange set Sparkling champagne metallic 4W
Colour exchange set Platinum white metallic 4W
Colour exchange set Graphite black metallic 4W
Trolleybag
Bracket for trolleybag
Front bag
Rear basket
Luggage carrier for seat frame
Walking aid bracket for chassis mounting (not for Gemino)
Walking aid bracket for chassis mounting (for Gemino)
Cane holder mounted to chassis
Cane holder mounted to chair, vertical
Cane holder mounted to chair, horizontal
30 | Spare parts
Trophy
Continued from 4,3 Options
Pos
9
10
10
11
12
13
-
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Article number
1003097
1010833
9000752
1002421
9000436
9000437
1015507
4824
1001752
1001753
9000825
1001809
1008572
9007569
9007499
1015595
Description
Clamp for cane and crutch holder (diameter 20 - 30 mm)
Mirror right
Bracket for mirror right
Mirror right with mounting bracket
Anti tip wheel left
Anti tip wheel right
Lap strap with roll-up for Master Seat
Retractable seat belt
Elevated footplate for SH 35 - 42 cm
Angle adjustable footrest, range of 0&deg; til 50&deg; (not i.c.w. 4-wheel)
Adjustment tool for rear spring
Foot throttle Egis for originial electronics (ID no &lt; QT02400)
Foot throttle S-Drive for originial electronics (ID no &lt; QT02400)
Assy foot throttle incl. assy top full option for advanced electronics (ID no &gt; QT02400)
Assy foot throttle for advanced electronics (ID no &gt; QT02400)
Tom Tom bracket
Trophy
31
| Service instructions
5
Trophy
Service instructions
This document is a reference book to be used to order parts for the scooter model shown on the front cover.
5.1 Maintenance plan
Below, we have indicated what needs to be checked, how often this should be done and by whom.
To be carried out by
Time
Description
Daily
Weekly
Charging the batteries, after each use
Checking the tyre pressures
Cleaning the scooter
Cleaning the upholstery (if necessary)
Grease the seat’s swivel mechanism: the seat needs to be removed for this. See
‘Removing the seat’. Lithium grease is recommended
Inspecting the electrical system
Checking the batteries
Inspecting the drive. (see 7.6)
Inspecting the mechanical parts
Inspecting the bearings
Inspecting the suspension
Checking the tyres
Checking all fastenings and bolts: tighten if necessary
Sign the inspection record table in the user manual
Monthly
Every three
months
Annually
User
x
x
x
x
Dealer
-
x
x (Annually)
-
x
x
x
x
x
x
x
x
x
It is recommended that the dealer carries out a service on the scooter at least once a year. If the scooter is used intensively, the
service should be carried out every six months.
Maintenance requirement for re-use
Disinfect surfaces with commercially available disinfectants and clean the surfaces with damp cloths and cleaners tuned.
Warning
Do not use high pressure cleaners or similar to clean the product!
The following work most be carried out before re-use:
Annual inspection
1
Electronics
On / off switch
Output connector
Operation
Brake
Programmable settings
Batteries
Level
Connections
Capacity test
Wheels and tyres
Tread depth
Pressure
Bearings
Wheel fixing nuts
Motors
Cables
Noise
Connections
Brake
Brushes
2
3
4
5
6
7
Trophy
Service instructionsTrophy
| 32
Annual inspection
1
2
3
4
5
6
7
Chassis
Condition
Steering
Seating
Seat
Backrest
Armrests
Electrical
Harnesses
Connections
Lighting system
Test
Forwards
Backwards
Emergency stop
Left turn
Right turn
Uphill / downhill
Obstacle
Brake
List of necessary repairs:
Warning
Pull the charge cable out of the battery charging connection of the scooter before carrying out any maintenance on the scooter.
5.2 Batteries
Always follow the instructions related to battery maintenance &amp; storage as given by the battery manufacturer ( Battery
charger).
The scooter is equipped with gel batteries. These batteries are fully encased and sealed and require no maintenance. A sticker
indicates how the batteries are to be connected. This sticker is located on the rear cover and on the battery cable.
Warning
Ensure that the batteries are always well charged.
Do not use the scooter if the batteries are almost flat. Doing so may damage the batteries and means you run the risk of coming
to an unexpected standstill.
Ensure that the batteries are never completely flat. This can seriously damage the batteries and shorten their lifespan.
Only use gel-batteries
Replacing the batteries
If battery capacity is so low (after fully charging) that the scooter can only make short trips, or can not be driven at all, then the
batteries have reached the end of their lifespan. Replace the batteries as soon as possible.
Warning
Once the new batteries have been put in place they will need to be charged and ‘run in’ ( Battery charger)
For the correct way to dispose of batteries see ( Scooter) ‘Used scooters and the environment’
Trophy
33
| Service instructions
Trophy
Cleaning the batteries
Gel batteries are maintenance-free. However, attention may be paid to the following matters:
Note!
Ensure that the batteries remain clean and dry: dirt and water can cause leaks, as a result of which battery capacity can be
reduced.
Clean the battery terminals and then grease them using acid-free Vaseline.
5.3 Tyres
To ensure that your scooter performs well, it is of great importance for the tyres to be kept at the right pressure.
Inflating the tyres
The tyres are equipped with a car tyre valve. Remove the caps from the valves before inflating the tyres. If the tyres are not
adequately inflated, the range of the scooter may be reduced and the tread may wear more quickly.
Warning
When inflating tyres, never exceed the maximum recommended tyre pressure which is stated on the tyres (2.4 bar front and 2.2
bar rear).
Never forget to replace the valve cap after inflating the tyres. The valve cap prevents dirt and sand from getting into the valve.
See the ‘Maintenance table’ regarding tyre checks.
5.4 Assembly, replacement and adjustment instructions
This chapter covers illustrated assembly, replacement and adjustment instructions.
Every separate visual instruction is prefaced with:
• Preparations
• Instructions (suggestions and advice to help you carry out tasks or procedures more easily)
• Relevant article numbers
• Tools used
• Notices (extra notes covering information you need when executing the specific task)
The tools for the specific task are illustrated in the visual instructions. The visual instructions are based on the Trophy 20,
functioning for the Trophy is similar, but therefore may visual deviate from the Trophy.
Trophy
5.4.1
Service instructionsTrophy
| 34
Console
Replacing the throttle for original electronics (ID-no &lt; QT02400)
• Assemble the gas throttle (7 and 6)
Warning! Assembly of the screws until the black
steering wheel material starts to deform. Afterwards
the gas throttle must be checked on normal freedom
of movement. This can be checked by moving the gas
throttle to reverse and to forward direction. The gas
throttle must return by itself to its middle position. The
gas throttle should not stick! If the gas throttle sticks,
loosen the screws a few turns, until sticking of the gas
throttle disappears. If the problem still exists, please
contact service department of Handicare.
• Assemble the tiller pcb (3). (3 screws)
Note! Place the gas throttle harnesses in the outermost
corners of the console. Make sure that no harness is
visible through the middle hole of the PCB. (This is the
space for the speed switch on the console panel.)
• Assemble the console panel (1) (4 screws). Connect the
console panel harnesses. The harness from the speed
switch should be routed underneath the tiller PCB.
• Assemble the pull relief with the supplied ty-rap to the
steering column.
• Assemble the tiller cover (5) (4 screws)
• Connect the batteries.
• Turn the scooter on and test the gas throttles. If in doubt,
always contact the service department of Handicare
Preparation
• Switch off the scooter with the ignition key.
• Disconnect the batteries.
Instructions
The following operations are required to replace throttle:
Unscrew the gas throttle:
Note! Suitable work area required!
• Remove the console panel (1) (4 screws) and
disconnect the console panel harnesses.
• Remove the tiller PCB (3) (3 screws).
• Remove the front tiller cover (5) (4 screws) from the
steering column
• Remove the ty-rap which functions as a pull relief for
the wiring.
• Remove the screws (6) from the throttle levers (7). Take
the throttle levers out the steering wheel.
• Guide the steering harness from the console. The tiller
PCB should be lifted to do this. Never pull on a throttle
lever or on a connector. This can result in serious
product faults.
• Disconnecting the gas throttle connector requires
precise handling. For the best result use a small flat
screw driver. Push the tip of the screwdriver under the
foremost (longest) lip and gently pull the connectors.
The connectors will come loose and the gas throttle can
be removed.
Mounting the gas throttle:
• Assemble the two included white plastic bushes (7) in
combination with the two mounting screws (6).
• Attach the connector of the gas throttle to the connector
of steer harness.
• Guide the cable steer harness gently in the steer
towards the console. Guide the harness from the
console. Make sure the gas throttle connector is
positioned inside the steering wheel metalwork. The gas
throttle can be assembled.
1
Relevant article numbers
• 9007083 Foot throttle Advanced electronics
• 1008730 4,8x19 self tapping screw
Tools used
• Allen key, 3 mm
• Metal drill, 6 mm
• Drill
• Screwdriver, crosshead
2
Trophy
3
4
5
5
Trophy
Mount the throttle controls for original electronics (ID-no &lt; QT02400)
Safety comes first in the present design of the gas throttle circuit. This means that a build to order Trophy is specifically build to
the requested configuration. There is no more ‘loose’ wiring to make rebuild afterwards easier. This means that converting the gas
throttles would require pulling electrical wiring through the steering wheel.
To make this conversion easier and safer for the dealer we have created an exchange pool of complete steering wheels with
throttles and wiring. You can buy an exchange steering wheel, rebuild the Trophy and return the ‘old’ steering wheel. This way it
costs you little time, you can realize a swift rebuild with little waiting time for the end user and do it in the safest way.
Loose cables will no longer be available as parts delivery. Our advice in converting gas throttles is to always use an exchange- or
new steering wheel assembly.
Partnumber
1008342
9002671
1008343
9002672
1008344
9002673
Description
Revision steering wheel with left throttle Egis
Revision steering wheel with left throttle S-Drive
Revision steering wheel with right throttle Egis
Revision steering wheel with right throttle S-Drive
Revision steering wheel with dual throttle Egis
Revision steering wheel with dual throttle S-Drive
Different types of throttle controls
1
Red throttle control
Warning! Never use!
3
Grey throttle control with black lock and warranty seal
Warning! Use on an updated product, see label near serial
number. Use on Trophy with S-Drive.
2
Grey throttle control
Warning! Never use!
Refund
• 60
• 60
• 60
• 60
• 60
• 60
Trophy
Replacing the throttle for advanced electronics (ID-no &gt; QT02400)
Preparation
• Switch off the scooter with the ignition key.
Relevant article numbers
• 1008055 Throttle (potentiometer)
Instructions
The following operations are required to replace the
throttle:
Note! Suitable work area required!
• Remove the two sheet metal screws and the throttle;
disconnect in between the connector of the throttle.
• Mount the new throttle.
• Rebuild the scooter in the reverse order.
Tools used
• Screwdriver, crosshead
1
Notice
• N.a.
2
Trophy
5.4.2
Front frame 3W
Replacing the front wheel and fork
Preparation
• Switch off the scooter with the ignition key.
• Use a lifting device to raise the scooter clear of the
ground.
Instructions
The following operations are required to replace the front
fork 3W:
• Remove the front cover and the front cover rear part.
• Remove the retaining ring and spiral pin.
• Remove the complete fork with wheel.
• Remove the hexagon nut, washer and bolt to take out the
wheel.
• Replace the new front fork 3W.
• Rebuild the scooter in the reverse order.
Relevant article numbers
• 9000504 Front fork
Tools used
• Torque wrench, socket, 13 mm
• Screw driver, crosshead
• Hammer (plastic)
• Chaser
• Circlip pliers
• Open ended spanner, 13 mm
Notice
• Some parts need to be replaced; the replacement is
indicated by a symbol.
• Some operations have to be carried out by two persons;
this is indicated by a symbol.
1
2
3
4
39 | Service instructions
Trophy
5
40 | Service instructions
5.4.3
Trophy
Front frame 4W
Replacing the front wheel
Preparation
• Switch off the scooter with the ignition key.
• Use a lifting device to raise the scooter clear of the
ground.
Instructions
The following operations are required to replace the front
wheel:
• Remove the cover and the four hexagon screws to
remove the front wheel.
• Mount the new front wheel in the reverse order.
Relevant article numbers
• 9001815 Front wheel 4W
Tools used
• Screwdriver, medium
• Torque wrench, socket bit, 6 mm
Notice
• N.a.
1
2
3
4
Trophy
Service instructions | 41
Adjustment shock absorber - front
Preparation
• Switch off the scooter with the ignition key.
Tools used
• 9000825 Suspension adjustment key
Instructions
The following operations are required to adjust the shock
absorber - front:
• Read the table for more information about the adjustment
of shock absorbers.
• Use the suspention adjustment key to adjust the shock
absorber as desired.
Notice
• Position 0 soft and position 4 hard
Relevant article numbers
• N.a.
1
42 | Service instructions
Trophy
Replacing the shock absorber - front
Preparation
• Switch off the scooter with the ignition key.
• Use a lifting device to raise the scooter clear of the
ground.
Instructions
The following operations are required to replace the shock
absorber - front:
Note! Suitable work area required!
• Remove the basket, the front tiller cover, the mounting
bracket for the mirrors, the front cover, the front spoiler,
the front cover rear part, the front fender L/R, the front
cover bottom and the front bumper.
• Remove the Allen hexagon screws and locknut form the
shock absorbers on the swing arm top and lower assy.
• Remove shock absorber
• Adjust the new shock absorber according the
specifications.
• Replace the new and adjusted shock absorber.
• Rebuild the scooter in the reverse order.
• Note! Be sure you fasten all bolts and nuts with the
correct torque!
1
Relevant article numbers
• 9001641 Shock absorber - front
Tools used
• Torque wrench, socket,17 mm
• Socket, 7 mm
• Screwdriver, crosshead
• Allen key, 8 mm
• 9000825 Suspension adjustment key
Notice
• Position 0 soft and position 4 hard
2
Trophy
3
Service instructions | 43
4
44 | Service instructions
Trophy
Replacing the swing arms (top and lower assy)
Relevant article numbers
• 9002091 Swing arm lower assy
• 9002090 Swing arm top assy
Preparation
• Switch off the scooter with the ignition key.
• Use a lifting device to raise the scooter clear of the
ground.
Tools used
• Torque wrench, socket, 7 mm-13 mm / socket bit, 6 mm
• Torque wrench, socket, 17 mm
• Allen key, 8 mm
• Screwdriver
• Open ended spanner, 10 mm
Instructions
The following operations are required to replace the swing
arms:
Note! Suitable work area required!
• Remove the front spoiler.
• Remove the cover and the hexagon bolt to remove the
front wheel.
• Remove the hexagon screw from the lower swing arm.
• Remove the two axle suspension parallel bolts.
• Remove the lock nut at the wheel side of the swing arm
and turn the swing arm out of its position.
• Replace the new swing arm.
• Rebuild the scooter in the reverse order.
1
3
Notice
• N.a.
2
4
Trophy
5
7
Service instructions | 45
6
46 | Service instructions
5.4.4
Trophy
Rear frame
Replacing the rear wheel
Preparation
• Switch off the scooter with the ignition key.
• Use a lifting device to raise the scooter clear of the
ground.
Instructions
The following operations are required to replace the rear
wheel:
Note! Suitable work area required!
• Remove the cover and four hexagon head cap screws to
remove the rear wheel.
• Mount the new rear wheel in the reverse order.
Relevant article numbers
• 9000550 Rear wheel white, left-side with brake drum
• 9001996 Rear wheel grey, left-side with brake drum
• 1015104 Rear wheel grey, left-side with brake drum and
block profile
• 9001172 Rear wheel white, left side standard
• 9001998 Rear wheel grey, left side standard
• 1015154 Rear wheel grey, left side standard with block
profile
• 9000549 Rear wheel white, right-side with brake drum
• 9001995 Rear wheel grey, right-side with brake drum
• 1015103 Rear wheel grey, right-side with brake drum and
block profile
• 9001173 Rear wheel white, right side standard
• 9001997 Rear wheel grey, right side standard
• 1015153 Rear wheel grey, right side standard with block
profile
Tools used
• Screwdriver
• Torque wrench, socket bit, 6 mm
Notice
• N.a.
1
2
3
4
Trophy
Service instructions | 47
Replacing the mechanical brake
Preparation
• Switch off the scooter with the ignition key.
• Use a lifting device to raise the scooter clear of the
ground.
Instructions
The following operations are required to replace the
mechanical brake:
Note! Suitable work area required!
• Remove the cap and hexagon flange bolt to remove the
rear wheel.
• Remove the brake cable.
• Remove the two hexagon head cap screw and remove
the brake.
• Mount the new brake.
• Rebuild the scooter in the reverse order.
• Use Loctite 243 before fastening the hexagon flange bolt
with 90 Nm.
Relevant article numbers
• 1002576 Brake right
• 1002577 Brake left
Tools used
• Screwdriver
• Torque wrench, socket, 16 mm
• Allen key, 5 mm
• Loctite 243
Notice
• N.a.
1
2
3
4
Note! Use Loctite 243 at the indicated locations during
assembling the scooter.
48 | Service instructions
5
Trophy
Trophy
Service instructions | 49
Replacing the carbon brushes
• Rebuild the scooter in the reverse order.
Preparation
• Switch off the scooter with the ignition key.
• Disconnect the batteries.
• Use a lifting device to raise the scooter clear of the
ground.
Relevant article numbers
• 1002646 Carbon brush for Trophy with Egis
• 10.300.031.000 Carbon brush for Trophy with S-Drive
• 1011585 Carbon brush set for CT transaxle
Instructions
The following operations are required to replace the carbon
brushes:
Note! Suitable work area required!
• Remove the rear cover.
• Disconnect all motor connectors from the S-drive
controller.
• Lock the freewheel lever.
• Remove four hexagon bolts and remove the motor
cover.
• Unscrew the carbon brush cover.
• Pull the carbon brush out of the housing and remove the
brush.
• Inspect the collector on the anchor of the motor; if the
collector is seriously worn, replace the entire drive unit.
• Clean the collector on the anchor of the motor from dust
with pressed air.
• Place the carbon brush in the holder; this can be done in
one way only.
• Screw the new plastic screw cap onto the carbon brush
holder.
1
Tools used
• Lifting device
• Screwdriver short
• Allen key, 4 mm
• Socket, 7 mm, 10 mm and 16 mm
Notice
• Some parts need to be replaced; the replacement is
indicated by a symbol.
• Make sure the scooter is switched off.
2
50 | Service instructions
3
Trophy
Trophy
Service instructions | 51
Replacing the motor brake
Relevant article numbers
• 1003225 Motor brake Egis
• 9003243 Motor brake S-drive
• 1012104 Motor brake for CT transaxle
Preparation
• Switch off the scooter with the ignition key.
• Disconnect the batteries.
• Use a Lifting device to raise the scooter clear of the
ground.
Tools used
• Screwdriver
• Socket, 7 mm
• Allen key, 4 mm
Instructions
The following operations are required to replace the free
wheel lever:
Note! Suitable work area required!
• Remove the rear cover.
• Disconnect all motor connectors from the S-drive
controller and the speed sensor cable.
• Lock the freewheel lever.
• Remove the four hexagon bolts and remove the motor
cover.
• Remove the hexagon screws and remove the free wheel
lever.
• Mount the new free wheel lever.
• Rebuild the scooter in the reverse order.
1
Notice
• Some parts need to be replaced; the replacement is
indicated by a symbol.
• Make sure the scooter is switched off.
2
52 | Service instructions
3
5
Trophy
4
Trophy
Service instructions | 53
Replacing the transaxle
Relevant article numbers
• 1007947 Transaxle Schmid Trophy 3 and 4 wheel, Egis
• 1007961 Transaxle Trophy Alpine, Egis (max 11 km/h)
• 1008565 Transaxle Trophy Alpine, S-Drive (max 11
km/h)
• 1013184 Transaxle CT Trophy 3 and 4- wheel, S-Drive
Preparation
• Switch off the scooter with the ignition key.
• Disconnect the batteries.
• Use a lifting device to raise the scooter clear of the
ground.
Instructions
The following operations are required to replace the
transaxle:
Note! Suitable work area required!
• Remove the rear cover.
• Disconnect all motor connectors from the S-drive
controller and the speed sensor cable..
• Lock the freewheel lever.
• Remove the cover and hexagon flange bolt to remove
the rear wheel.
• Remove the brake cable
• Remove the two hexagon head cap screws to remove
the brake mounting, key and brake.
• Remove the four lock nuts and remove the transaxle and
rubber mounting strips.
• Mount the new the transaxle.
• Rebuild the scooter in the reverse order.
• Use Loctite 243 before fastening the hexagon flange bolt
with 90 Nm.
1
Tools used
• Socket, 7 mm
• Socket, 17 mm
• Torque wrench, socket, 16 mm
• Screwdriver
• Allen key, 4 mm
• Loctite 243
Notice
• Some parts need to be replaced; the replacement is
indicated by a symbol.
• Make sure the scooter is switched off.
2
54 | Service instructions
3
Trophy
4
Note! Use Loctite 243 at the indicated locations during
assembling the scooter.
5
6
Trophy
Service instructions | 55
Adjustment the shock absorber - rear
Preparation
• Switch off the scooter with the ignition key.
Relevant article numbers
• N.a.
Instructions
The following operations are required to adjust the shock
absorber - rear:
Note! Suitable work area required!
• Remove the seat.
• Remove the battery cover.
• Loosen the battery strap.
• Disconnect all connectors from the battery.
• Remove the battery.
• Read the table for more information about the
adjustment of shock absorbers.
• Use the special adjustment tool to adjust the shock
absorber as desired.
• Rebuild the scooter in the reverse order.
Tools used
• 9000825 Suspension adjustment key
1
Notice
• Make sure the scooter is switched off.
2
56 | Service instructions
3
4
Trophy
Trophy
Service instructions | 57
Replacing the shock absorber - rear
Relevant article numbers
• 9000603 Shock absorber standard
• 9000683 Shock absorber heavy duty
Preparation
• Switch off the scooter with the ignition key.
Instructions
The following operations are required to replace the shock
absorber - rear:
Note! Suitable work area required!
• Remove the seat.
• Lift the scooter to raise the wheels clear from the
ground.
• Remove the rear cover.
• Remove the battery cover.
• Remove the bolts of the rollbar 6x
• Remove the roll-bar
• Remove the hexagon head cap screw
• Take out the shock absorber.
• Read the table for more information about the
adjustment of shock absorbers.
• Use the special adjustment tool to adjust the shock
absorber as desired.
• Mount the new, correct adjusted, shock absorber.
• Rebuild the scooter in the reverse order.
1
Tools used
• Socket, 7 mm / 17 mm
• Allen key, 8 mm
• 9000825 Suspension adjustment key
Notice
• Make sure the scooter is switched off.
2
58 | Service instructions
Trophy
3
4
5
6
Trophy
Service instructions | 59
Replacing the tiller PCB
Relevant article numbers
• 9000496 PCB console for original electronics (ID-no &lt;
QT02400)
• 9008789 Tiller PCB Basic for advanced electronics (IDno &gt; QT02400)
• 9008791 Tiller PCB Dual control for advanced
electronics (ID-no &gt; QT02400)
• 9008790 Tiller PCB Full option for advanced electronics
(ID-no &gt; QT02400)
Preparation
• Switch off the scooter with the ignition key.
• Disconnect the batteries.
Instructions
The following operations are required to replace the tiller
PCB:
Note! Suitable work area required!
• Remove the basket and the mounting bracket for the
mirrors.
• Remove the two bolts and remove the front tiller cover.
• Remove the tyrap
• Remove the nut, the four Ejot screws and the
dashboard.
• Disconnect all connectors from the tiller PCB.
• Remove the three Ejot screws to remove the tiller PCB.
• Mount the new tiller PCB.
• Rebuild the scooter in the reverse order.
Tools used
• Socket, 10 mm
• Screwdriver, crosshead
Notice
• Make sure the scooter is switched off.
1
2
3
4
60 | Service instructions
Trophy
Replacing the stop switch
Relevant article numbers
• 9006138 Emergency stop
Preparation
• Switch off the scooter with the ignition key.
• Disconnect the batteries.
Tools used
• Socket, 10 mm
• Screwdriver, crosshead
Instructions
The following operations are required to replace the stop
switch:
Note! Suitable work area required!
• Remove the basket and the mounting bracket for the
mirrors.
• Remove the two bolts and remove the front tiller cover.
• Remove the nut, the four Ejot screws and the
dashboard.
• Remove the tyrap
• Disconnect all connectors from the tiller PCB.
• Remove the three Ejot screws to remove the tiller PCB.
• Disconnect the connectors of the console bottom.
• Remove the recessed button head and Ejot screws,
disconnect the connectors the stop switch and remove
the top and bottom steering wheel covers.
• Mount the new stop switch.
• Rebuild the scooter in the reverse order.
1
Notice
• Make sure the scooter is switched off.
2
Trophy
Service instructions | 61
3
4
5
6
62 | Service instructions
5.4.5
Trophy
Electronics
Replacing the controller
Relevant article numbers
• 1008074 Controller Egis 110A
• 9002457 Controller S-Drive 120A (ID-no &gt; LT03210)
• 1012504 Controller S-Drive 140A
Preparation
• Switch off the scooter with the ignition key.
• Disconnect the batteries.
Instructions
The following operations are required to replace the
controller:
Note! Suitable work area required!
• Remove the rear cover.
• Remove the S-drive cover.
• Disconnect all connectors from the S-drive controller.
• Remove the two hexagon head cap screws and remove
the controller.
• Mount the new controller.
• Rebuild the scooter in the reverse order.
1
3
Tools used
• Allen key, 5 mm
Notice
• In case of S-drive controller 90A watch out for motor
harness and power harness.
2
Trophy
5.4.6
Service instructions | 63
Accessories
Mount the crutch holder, horizontal
Preparation
• Switch off the scooter with the ignition key.
Relevant article numbers
• 1003095 Crutch holder mounted to chair, horizontal
Instructions
The following operations are required to mount the
horizontal crutch holder:
Note! Suitable work area required!
• Mount the horizontal crutch holder with two bolts on the
seat frame.
Tools used
• Open ended spanner, 10 mm
1
2
10
1
2
110948-03-002
110948-03-003
64 | Service instructions
Trophy
Mount the crutch holder, vertical
Preparation
• Switch off the scooter with the ignition key.
Relevant article numbers
• 2537 Crutch holder mounted to chair, vertical
Instructions
The following operations are required to mount the vertical
crutch holder:
Note! Suitable work area required!
• Remove the armrest from the backrest frame.
• Mount the vertical crutch holder and the armrest with two
bolts back on the backrest frame.
Tools used
• Allen key, 6 mm
1
2
1
2
2
3
6
1
6
110948-03-010
110948-03-011
Trophy
Service instructions | 65
Mount the luggage carrier
Preparation
• Switch off the scooter with the ignition key.
Relevant article numbers
• 1001813 Luggage carrier
Instructions
The following operations are required to mount the luggage
carrier:
Note! Suitable work area required!
• Remove the armrest from the backrest frame.
• Mount with the two bolts on every side the luggage
carrier on the backrest frame.
Tools used
• Allen key, 6 mm
1
2
6
2
6
2
1
1
3
110948-03-005
110948-03-012
66 | Service instructions
Trophy
Mount the walking aid holder
Preparation
• Switch off the scooter with the ignition key.
Relevant article numbers
• 1001814 Walking aid holder
Instructions
The following operations are required to mount the walking
aid holder:
Note! Suitable work area required!
• Remove the armrest on both sides from the backrest
frame.
• Mount with the two bolts on every side the walking aid
holder on the backrest frame.
Tools used
• Allen key, 6 mm
1
2
6
6
2
2
1
1
3
110948-03-005
110948-03-009
Trophy
Service instructions | 67
Mount the mounting bracket
Relevant article numbers
• 9000620 Mounting bracket rear
• 4930
Basket
• 1015545 Trolley bag
Preparation
• Switch off the scooter with the ignition key.
Instructions
The following operations are required to mount the
mounting bracket:
Note! Suitable work area required!
• Remove the armrest on both sides from the backrest
frame.
• Mount with the two bolts on every side the mounting
bracket on the backrest frame.
• Put the basket or trolley bag on the mounting bracket.
1
Tools used
• Allen key, 6 mm
2
6
6
2
2
1
1
3
110948-03-006
110948-03-005
3
4
110948-03-007
110948-03-008
68 | Service instructions
Trophy
Mount the lap strap with roll-up to the Master seat
Preparation
• Switch off the scooter with the ignition key.
Relevant article numbers
• 1015507 Lap strap with roll-up for Master Seat
Instructions
The following operations are required to mount the lap
strap with roll-up to the Master Seat:
Note! Suitable work area required!
• Unzip the cover from the Master seat
• The frame has a hole on the left and right side. Make on
both sides (at the level of the hole) a notch in the cover.
• Left side: The locknut needs to be mounted on the inside
of the frame.
• Right side: The plastic bushings and pivot van needs to
be used on the right side.
• When everything is mounted, place the black cap on the
bolts.
• Turn the flaps of the cover with velcro inside and close
the zipper carefully. Fold also the zipper back inside.
1
Tools used
• Socket, 17 mm
2
Trophy
5.4.7
Service instructions | 69
Upgrade instructions controllers
Mount the foot throttle for advanced electronics (ID-no &gt; QT02400)
The following operations are required to mount the foot
throttle:
Note! Suitable work area required!
Note! Remove always one finger-control! Replace it with
cover steering wheel 9007423.
Note! In case you have a basic display, a advanced display
will be delivered with the foot throttle. Dismount the basic
display and mount the advanced display.
• Loosen the floor mat from the frame.
Note! For mounting the foot throttle on the floor mat you
have to drill two holes in the floor mat and frame. Be
sure you will not damage any cables mounted under the
frame!
• Determine the exact laying of the cables under the
frame.
• Reposition the cables in case they will be damaged
while drilling the two holes.
• Replace the floor mat and position the foot throttle
mounting plate on the floor mat.
• Drill the holes and mount the foot throttle mounting plate.
• Mount the foot throttle on the mounting plate.
• Guide the cable trough and under the frame, to the
electronics compartment on the backside of the scooter.
• Remove the rear cover.
• Connect the plug to the socket in the electronics
compartment and replace the rear cover.
Preparation
• Switch off the scooter with the ignition key.
• Disconnect the batteries.
Instructions
Basic display
Advanced display
Relevant article numbers
• 9007083 Foot throttle Advanced electronics
• 1008730 4,8x19 self tapping screw
Tools used
• Allen key, 3 mm
• Metal drill, 6 mm
• Drill
• Screwdriver, crosshead
Note! This procedure is intended for the Throphy with the
latest electronics. In case your Trophy has the dashboard
as one above, you have the latest version electronics.
Contact Handicare in case you have another dashboard
(original electronics ID-no &lt; QT02400).
1
2
3
2
1
2
3
3X
&Oslash;6
1
3
110948-03-021
70 | Service instructions
Trophy
4
3
110948-03-022
5
110948-03-023
Trophy
Service instructions | 71
Expand controller options for advanced electronics (ID-no &gt; QT02400)
Function button foils on dashbord
Basic foil
Yes
No
Yes
No
Yes
Left throttle selection switch
Revers switch for foot throttle
Display menu selection switch
Cruise control switch
Right throttle selection switch
Advanced foil
Yes
Yes
Yes
Yes
Yes
Trophy's equipped with the finger/hand control the basic foil will be used If the foot throttle and/or cruise control is chosen, the
advanced foil (with all icons) will be used. Be aware that the switches are always visible on the foil but not working when an
option is not selected.
Upgrade can be done via spare part options (see matrix below):
to
from
Right hand
Left hand
Foot
Hand/foot
Dual hand
CC (only works with 8)
0.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Right hand
Left hand
Foot
Hand/foot
Dual hand
CC
Emergency
stop
0
1
0
0
standard
0
1
0
0
0
2
2
0
2
10
2+4
2+4
1+4
2
10
1+4
1+4
2x1+4
1
1
5+7+8 or (9)
5+7+8 or (9)
5+8 or (9)
5+8 or (9)
5+7+8 or (1+9)
-
8
8
8
8
8
standard
Only remove/replay parts
1008055 Throttle potentiometer
9007569 Assy foot throttle incl. assy top full option (7)
9008789 Tiller PCB Basic
9008791 Tiller PCB Dual control
9008790 Tiller PCB Full option
9007568 Assy top standard (basic foil)
1012535 Assy top full option (advanced foil)
9006138 Emergency stop button
1016535 Full option steering wheel (includes 1+5+7+8)
9007499 Assy foot throttle
Since Full option steering wheel only means to exchange the complete steering wheel, this may be advisable to use always as
upgrade for Cruise Control on single hand/finger control.
Cruise control will only work together with the Emergency Stop Button. If this button doesn’t function or isn’t present, the scooter
will give an error and will not start. (Safety!)
72 | Service instructions
Trophy
5.5 Display menu settings
Starting the service menu for original electronics (ID-no &lt; QT02400)
E
E
G
M
I
Dealer
R
Kilometer total (user)
Hold the hazard light button and press the left horn button briefly
Reset total (user
Push the I button (3 sec.)
Kilometer total (scooter)
Hold the hazard light button and press the left horn button briefly
Hours-on total (scooter)
Hold the hazard light button and press the left horn button briefly
Battery voltage
Hold the hazard light button and press the left horn button briefly
Leave dealer menu
Any other button
User
R
km/h
Push the I button
R
Daily kilometer counter Push the I button
R
Reset daily counter
Push the I button (3 sec)
R
Kilometer total (user)
Push the I button
It’s possible to fit the Trophy with either one foot throttle, one hand throttle or two hand throttles. See technical diagram chapter 7.
Warning!
A combination of foot throttle and finger control is not possible.
Any guarantee on the Trophy is invalidated by the third-party fitting of electronic circuits, other than as described below, which
interfere with the finger control or foot throttle signal.
Trophy
Service instructions | 73
Starting the service menu for advanced electronics (ID-no &gt; QT02400)
R
S
P
B
R
E
E
G
C
I
Pushing the hazard-button (G) together with the claxon-button (E) more than 2 seconds, the service menu shall be visible.
• First information shown after starting the service menu is the “Total km-1”
• Pushing the hazard button again (G) allows you to scroll through the menu shown below.
• If any other button (other than the DSS (I), horn (E), hazard button (G)) is switched during the service menu, the display
returns to the user menu and will show “actual speed”
When the batteries of the scooter are removed the service information shall not get lost for at least 1 year.
The display will blink at a frequency of 1-2HZ, indicating this value can be changed.
1.
Total km-1 (S)
The amount of km the scooter has driven after the last time this value was reset.
Resettable by pressing the DSS (I) switch ≥ 2 seconds.
2.
Total km-2 (S)
The amount of km the scooter has ever driven in its total life.
3.
Actual battery voltage (B)
The actual battery voltage measured real time
4.
Hours ON
The amount of hours the scooter has been switched on in its life.
First one character of the display show: H
5.
Hours Driven
The amount of hours the scooter has driven more than 5% of its maximum speed in its life.
First one character of the display show: h
6.
Software version
First one character of the display show: F
7.
Signal Actual throttle input: Range
Actual input of the active throttle available (R)
First characters of the display show: C
The Icons on the tiller display will indicate the active throttle:
• right hand is lit: right hand side throttle is active
• left hand is lit: left hand side throttle is active
• no hand icons are lit: foot throttle is active
Foot throttle information is converted by the MC into a drive signal. This signal will be presented here. OK
74 | Service instructions
8.
Miles / hour reset (P)
Set speed and distance calculations to km or miles.
• Km icon on display is shown = km: km per hour
• m icon on display is shown = miles: miles per hour
Default: km
Change by pressing the DSS (I) switch ≥ 2 seconds.
9.
Scooter type selection.
This reflects the diameter of the wheels used.
• “t30” Trophy speed algorithm (Trophy 30)
• “t20” Trophy speed algorithm (Trophy 20)
Default: “t30”
Change by pressing the DSS (I) switch ≥ 2 seconds.
Trophy
10. This reflects if a beeping sound is enabled
• &quot;0&quot; no beep when driving backward
• &quot;1&quot; beeping when driving backward
default: &quot;1&quot;
Change by pressing the DSS (I) switch ≥ 2 seconds
First one character of the display show: b
Setting the options
Not all options are standard available. Some options are only available as ordered at Handicare. Not activated values will not be
shown in the service menu.
11. Cruise Control enable (S)
• “0” disabled
• “1” enabled
Default: “0” = disabled
Change by pressing the DSS (I) switch ≥ 2 seconds.
First two characters of the display show: CC
12. Manual / intelligent throttle switch
• “0” off
• “1” Manual Throttle Switching (MTS)
• “2” Intelligent Throttle Switching (ITS)
• “3” ITS and MTS active
Default: “0” = off
Change by pressing the DSS (I) switch ≥ 2 seconds.
First two characters of the display show: tS
Trophy
6
Troubleshooting | 75
Troubleshooting
If the scooter doesn’t function, while the batteries are fully charged, check the following points.
A. Set the scooter off and then on again. Check if the problem is solved.
B. Check if all the battery connectors are properly attached and firmly connected.
C. Check whether the freewheel handle is in the DRIVE position.
D. Make sure the position of the speed controller has not changed.
E. If there is a problem, the lights of the battery condition meter flash. Use the table below to determine the cause of the problem.
Indication on the display
Description of problem
Corrective action
The complete LED bar flashes
rapidly.
The Controller security has found
something that causes a problem.
Switch off the scooter.
Check all connectors.
Check the condition of the batteries.
Consult the manufacturer if the LED bar continues
flashing after the scooter has been switched on.
Contact the manufacturer.
The socket LED is lit continuously
after the scooter is switched on.
Short circuit in the potentiometer.
Cabling from the Tiller PCB to the
controller interface is defective.
Cabling from the Tiller PCB to the touch
control is defective.
Tiller PCB is defective.
The first red LED of the LED bar is The batteries require charging or there Check all connections between the controllers
lit continuously.
is a poor connection to the batteries.
and the batteries. If the connections are OK, try
recharging the batteries.
LED bar left to right chase.
The batteries are being charged.
Disconnect the battery charger from the scooter.
Two LEDs of the LED bar are lit.
There is a poor connection to the motor. Check all connections between the controller and
the motor.
Three LEDs of the LED bar are lit. There is a short circuit in the motor.
Check the motor cables or replace the motor.
Seven LEDs of the LED bar are lit. The throttle was held in during start up. Restart the scooter without pressing the throttle.
Speed potentiometer fault.
Check or replace the speed potentiometer.
Eight LEDs of the LED bar are lit. The controller is malfunctioning.
Replace the controller.
Nine LEDs of the LED bar are lit.
The neutral handle is in the neutral
Put the neutral handle in the drive position.
position.
Check the connections between the brake and the
The brake is malfunctioning.
controller.
Replace the brake.
Ten LEDs of the LED bar are lit.
The battery is malfunctioning.
Check the connections between the batteries and
the controller.
Check the batteries.
The table below provides explanation for the trip codes that can be indicated by the controller. These trip codes can be read with
the manual programming unit (SP1) or the mobility programmer PG.
LED code
1
1
2
3
4
4
6
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
Trip code
2c00
2c01
3B01
1400
7000
7001
1e03
0810
0814
0815
0816
0817
0300
1d02
2f01
0002
0003
0100
0203
0204
1501
1705
1802
Error type
Low battery error
Low battery error
Motor fault 1
Bridge fault 1
Startup with push selected
Push activated in drive mode
Inhibit activated
Tiller fault 1
Tiller reference error
Tiller lo reference error
Tiller high reference iso error
Tiller lo reference error
Speed Limit Potentiometer wiper open
Front end spec change trip
Tiller displaced error
Eeprom calibration checksum error 2
Eeprom program checksum error 2
Running checksum 1
Eeprom calibration checksum error 1
Eeprom program checksum error 1
Brake fault 2
Relay fault 1
Watchdog voltage ref error
Explanation
Low battery voltage
Low battery voltage
Motor disconnected
Motor wiring fault
Parking brake off
Parking brake off
Inhibit active
Throttle trip
Throttle trip
Throttle trip
Throttle trip
Throttle trip
Throttle trip
Throttle potentiometer trip
Throttle displaced at power up
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
76 | Troubleshooting
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
9
9
10
1805
1b20
2102
2d01
3100
3102
3210
3211
3212
3213
3600
3601
3602
3603
3608
3609
360a
360b
360c
360d
360e
4401
1500
1502
1600
Trophy
Salty finger ref error
Both clamps measuring current
Progres counter error
Front end spec change trip
Battery bridge difference error 1
Temperature settings incorrect
No internal timers
Internal timer out of range
Atod readings not finished before next read
Unknown mux channel
Hardware error
Test trip latch 1
Test trip latch 2
Test trip latch 3
Test trip latch 8
Test trip latch 9
Test trip latch 10
Test trip latch 11
Test trip latch 12
Test trip latch 13
Test trip latch 14
Generic ctrl error
Brake fault 1
Brake over current error
High battery error
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Possible controller trip
Solenoid brake fault
Solenoid brake fault
High battery voltage
Trophy
7
Technical product information | 77
Technical product information
7.1 CE Declaration and standards
This product complies with the regulations of the Medical Devices Directive and therefore
bears the CE mark.
Standard
Definition/description
EU guideline 93/42 EEC Applicable as mentioned in Appendix 1
The requirements from EN12182 as mentioned in NEN-EN 12184 (1999):
NEN-EN 12182 (1999)
Technical aids for the handicapped – General requirements and test methods
October 1997
NEN-EN 12184 (1999)
Electric wheelchairs, scooters and accompanying battery chargers –
Class C
Requirements and test methods 2009
Requirements and test methods for static, impact and fatigue strengths July
ISO 7176-8
1998
ISO 7176-9
Climate tests for electric wheelchairs and scooters
Requirements and test methods for control systems for electric wheelchairs
ISO 7176-14
1997
ISO 7176-16
Requirements for resistance to ignition of upholstered parts May 1997
Weight test dummy
N/A
160 kg
160 kg
160 kg
N/A
N/A
N/A
7.2 Technical specifications
Manufacturer
Model
Maximum user weight
Handicare&reg;
Trophy 3 wheels (3W)
Trophy 4 wheels (4W)
160 kg (25.2 stone)
Description
Total length
Total width
Minimum height*
Total weight excluding batteries
Total weight including batteries (80 Ah)
Weight of heaviest component
Static stability in the downward direction
Static stability in the upward direction
Lateral static stability
Distance range (ISO 7176-4)**
Dynamic stability
Maximum speed forwards
mm (inches)
mm (inches)
mm (inches)
kg (stones)
kg (stones)
kg (stones)
&deg;
&deg;
&deg;
km (miles)
&deg;
km/h (mph)
Back angle
Effective seat depth
Effective seat width
Back height (excl. head rest)
Seat height (front edge of seat)
&deg;
mm (inches)
mm (inches)
mm (inches)
mm (inches)
Armrest height
mm (inches)
Front armrest to backrest
Distance between armrests
Turning radius (ISO 7176-5)
Reversing width
Obstacle height (max. user weight)
Ground clearance (max. user weight / loaded)
mm (inches)
mm (inches)
mm (inches)
mm (inches)
mm (inches)
mm (inches)
Test data
Test weight
3W
1400 (55.1)
660 (26)
760 (29.9)*
110 (17.3)
155 (24.4)
90 (14.2)
15
15
15
60 (37.3)
11 (Alpine 14)
15 (Alpine 11)
(9.3, Alpine 6.8)
45 - 85 - 180
430 (16.9)
500 (19.7)
550 (21.7)
min 420 - max 550
(min 16.5 - max 21.2)
min 150 - max 340
(min 5.9 - max 13.4)
260 (10.3)
457 - 610 (18 - 24)
1250 (49.2)
1650 (65)
4W
1400 (55.1)
660 (26)
760 (29.9)*
121 (19.1)
166 (26.1)
101 (15.9)
15
15
15
60 (37.3)
11 (Alpine 14)
15 (Alpine 11)
(9.3, Alpine 6.8)
45 - 85 - 180
430 (16.9)
500 (19.7)
550 (21.7)
min 420 - max 550
(min 16.5 - max 21.2)
min 150 - max 340
(min 5.9 - max 13.4)
260 (10.3)
457 - 610 (18 - 24)
1750
1940 (76.4)
100 (3.9)
70 (2.8)
100 (3.9)
70 (2.8)
160 kg (25.2 stone)
78 | Technical product information
Trophy
Operating force
Operating handle
Parking brake
Electronic switches
Connecting the charger plug
&lt; 60 N
&lt; 60 N
&lt; 13.5 [N]
&lt; 60 [N]
Technical specifications for wheels
Front wheel diameter (3W)
Front wheel diameter (4W)
Rear wheel diameter
Tyre pressure 4W, front wheel
Tyre pressure 4W, rear wheel
Tyre pressure 3W, front wheel
Tyre pressure 3W, rear wheel
mm (inches)
mm (inches)
mm (inches)
bar (psi)
bar (psi)
bar (psi)
bar (psi)
320 x 60 (12.5 x 2.25)
320 x 60 (12.5 x 2.25)
410 x 80 (16.1 x 3.1)
2,5 (36.3)
2,5 (36.3)
2,5 (36.3)
2,5 (36.3)
Batteries
Maximum dimensions of batteries (lxbxh)
mm (inches)
334 x 178 x 253
(13.1 x 7 x 10)
Max. battery capacity C20
Max. battery capacity C5
Maximum permissible charging voltage
Maximum permitted charging current
Ah
Ah
Voltage
Amp&egrave;re
86
72
13.6
12 RMS
* Excluding seat and tiller folded down
** range dependent on user weight, condition of tyres, type of terrain, condition of battery and weather conditions with 80 Ah (C20)
7.3 Driving programs
The driving programs for Handicare products can be found on our FTP server.
Log on to the FTP server:
• Open internet explorer
• Go to ftp://mobilityftp.handicare.com
• Enter user name and password
User name: [email protected]
Password: dealer
• You will be logged on
• Select your wheelchair and the appropriate controller
• Click the file to download
Trophy
Technical product information | 79
7.4 Controller settings PG Drives Egis
Trophy Egis 120, 15 km/h
Speed Settings
Forward Acceleration (0,1 Seconds)
Forward Deceleration (0,1 Seconds)
Reverse Acceleration (0,1 Seconds)
Reverse Deceleration (0,1 Seconds)
Forward Speed (%)
Reverse Speed (%)
Fast
25
13
40
25
100
50
Operation Settings
Sleep timer (minutes)
Throttle Invert
0
On
Battery Settings
Low battery Flash Inhibit
TruCharge Cable Resistance (milli-Ohms)
TruCahrge Calibration
Max Charge Amps (0,1 Amps)
Min Charge Amps (0,1 Amps)
On
40
97
15
0
Inhibit Settings
Inhibit Mode
General Settings
Soft Stop
Output Voltage (Volts)
Pulsed Reverse Alarm
Brake Time (0,01 Seconds)
Freewheel Voltage
Freewheel Time-out (0,01 Seconds)
Slow
25
13
40
25
100
50
Factory Settings
Forward Acceleration (0,1 Seconds)
Forward Deceleration (0,1 Seconds)
Reverse Acceleration (0,1 Seconds)
Reverse Deceleration (0,1 Seconds)
Forward Speed (%)
Reverse Speed (%)
Max
100
100
100
100
100
100
Advanced Settings
Profile Top
Profile Bottom
40
80
Throttle Settings
Wig-Wag Throttle
Throttle Deadband (%)
Throttle Gain (%)
Iso Test
On
15
130
On
Options Settings
Options Register
17
Motor Settings
Current Limit Max (Amps)
Curerent Foldback Time (Seconds)
Current Foldback Level (%)
Hold Factor (%)
Bridge Hold Time (centi-Secs)
Motor Compensation (milli Ohms)
110
15
50
160
80
45
Factory Settings
Forward Acceleration (0,1 Seconds)
Forward Deceleration (0,1 Seconds)
Reverse Acceleration (0,1 Seconds)
Reverse Deceleration (0,1 Seconds)
Forward Speed (%)
Reverse Speed (%)
Max
100
100
100
100
100
100
Min
1
1
1
1
0
0
1
On
24
Off
60
100
20
Trophy Egis 120, 15 km/h, foot throttle
Speed Settings
Forward Acceleration (0,1 Seconds)
Forward Deceleration (0,1 Seconds)
Reverse Acceleration (0,1 Seconds)
Reverse Deceleration (0,1 Seconds)
Forward Speed (%)
Reverse Speed (%)
Fast
25
13
40
25
100
40
Operation Settings
Sleep timer (minutes)
Throttle Invert
0
Off
Battery Settings
Low battery Flash Inhibit
TruCharge Cable Resistance (milli-Ohms)
TruCahrge Calibration
Max Charge Amps (0,1 Amps)
Min Charge Amps (0,1 Amps)
On
40
97
15
0
Inhibit Settings
Inhibit Mode
General Settings
Soft Stop
Output Voltage (Volts)
Pulsed Reverse Alarm
Brake Time (0,01 Seconds)
Freewheel Voltage
Freewheel Time-out (0,01 Seconds)
Slow
25
13
40
25
100
40
Advanced Settings
Profile Top
Profile Bottom
40
80
Throttle Settings
Wig-Wag Throttle
Throttle Deadband (%)
Throttle Gain (%)
Iso Test
Off
15
120
On
Options Settings
Options Register
17
Motor Settings
Current Limit Max (Amps)
Curerent Foldback Time (Seconds)
Current Foldback Level (%)
Hold Factor (%)
Bridge Hold Time (centi-Secs)
Motor Compensation (milli Ohms)
110
15
50
156
80
45
1
On
24
Off
60
100
20
Min
1
1
1
1
0
0
80 | Technical product information
Trophy
7.5 Controller settings PG Drives S-Drive 120A
Trophy S-drive 120, 15 km/h
Speed Settings
Forward Acceleration (0,1 Seconds)
Forward Deceleration (0,1 Seconds)
Reverse Acceleration (0,1 Seconds)
Reverse Deceleration (0,1 Seconds)
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
Fast
35
13
40
25
100
10
40
5
On
Operation Settings
Sleep timer (minutes)
Throttle Invert
0
Yes
Battery Settings
Low battery Flash Level (Bars)
Cable Resistance (milli-Ohms
Calibration Factor
Low Battery Alarm
0
50
100
Off
Slow
35
13
40
25
100
10
40
5
Factory Settings
Acceleration (0,1 Seconds)
Deceleration (0,1 Seconds)
Forward Speed (%)
Reverse Speed (%)
Max
100
100
100
100
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
1
15
140
2
Throttle Reference Test
Iso Test Resistor
On
Off
Motor Settings
Current Limit Max (Amps)
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Curerent Foldback Time (Seconds)
Current Foldback Level (%)
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Compensation (milli Ohms)
Anti Rollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2: Speed (%)
Inhibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
1
Latching
0
1
Latching
0
1
Latching
0
0
General Settings
Soft Stop
Brake Time (milli-seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Pulsed Reverse Alarm
Diagnostic Alarm
Brake Disconnected Alarm
Brake Fault Detect
Brake Light
Freewheel Speed Limit
Freewheel Time Out (0,01 Seconds)
Freewheel Enable
Inhibit 2 Horn Input Enable
On
1500
24
0
(0 = Trucharge, 1 = LED, 2 = Analogue)
2
Off
Off
Off
Off
On
On
35
20
Disable
Off
110
120
10
110
15
50
120
80
18
20
12
0
1275
0
Min
1
1
0
0
0 = Drive,
1 = Inhibit,
2 = Trip
Trophy
Technical product information | 81
Trophy S-drive 120, 15 km/h, foot throttle
Speed Settings
Forward Acceleration (0,1 Seconds)
Forward Deceleration (0,1 Seconds)
Reverse Acceleration (0,1 Seconds)
Reverse Deceleration (0,1 Seconds)
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
Fast
35
13
40
25
100
10
40
5
On
Operation Settings
Sleep timer (minutes)
Throttle Invert
0
No
Battery Settings
Low battery Flash Level (Bars)
Cable Resistance (milli-Ohms
Calibration Factor
Low Battery Alarm
0
50
100
Off
Slow
35
13
40
25
100
10
40
5
Factory Settings
Acceleration (0,1 Seconds)
Deceleration (0,1 Seconds)
Forward Speed (%)
Reverse Speed (%)
Max
100
100
100
100
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
0
15
180
2
Throttle Reference Test
Iso Test Resistor
On
Off
Motor Settings
Current Limit Max (Amps)
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Curerent Foldback Time (Seconds)
Current Foldback Level (%)
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Compensation (milli Ohms)
Anti Rollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2: Speed (%)
Inhibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
1
Latching
0
1
Latching
0
1
Latching
0
0
General Settings
Soft Stop
Brake Time (milli-seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Pulsed Reverse Alarm
Diagnostic Alarm
Brake Disconnected Alarm
Brake Fault Detect
Brake Light
Freewheel Speed Limit
Freewheel Time Out (0,01 Seconds)
Freewheel Enable
Inhibit 2 Horn Input Enable
On
1500
24
0
(0 = Trucharge, 1 = LED, 2 = Analogue)
2
Off
Off
Off
Off
On
On
35
20
Disable
Off
110
120
10
110
15
50
120
80
18
20
12
0
1275
0
Min
1
1
0
0
0 = Drive,
1 = Inhibit,
2 = Trip
82 | Technical product information
Trophy
7.6 Controller settings PG Drives S-Drive 140A
Trophy S-drive 140, 15 km/h original electronics (ID-no &lt; QT02400)
Speed Settings
Forward Acceleration (0.1 Seconds)
Forward Deceleration (0.1 Seconds)
Reverse Acceleration (0.1 Seconds)
Reverse Deceleration (0.1 Seconds)
Fast
35
13
40
25
Slow
30
12
40
15
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
100
10
40
5
On
50
30
30
30
Operation Settings
Sleep Timer (Minutes)
Throttle Invert
0
Yes
Battery Settings
Low Battery Flash Level (Bars)
Cable Resistance (milli-Ohms)
Calibration Factor
Low Battery Alarm
0
100
100
Off
Trucharge Reset Voltage (Deci-Volts)
(S Drive 180A) (S Drive II)
Battery Curve Scaler
(S Drive II Only)
250
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2 Speed (%)
Inihibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
Factory Settings
Acceleration (0.1 Seconds)
Deceleration (0.1 Seconds)
Forward Speed (%)
Reverse Speed (%)
Off
1400
24
0
(0 = Trucharge, 1 = LED, 2 = Analogue)
2
Off
Pulsed Reverse Alarm
Diagnostic Alarm
Off
Off
Brake Disconnected Alarm
Off
Brake Fault Detect
Brake Light
On
On
Push too Fast Threshold
Push too Fast Timeout
Freewheel Enable
Inhibit 2 Horn Input Enable
35
20
Disable
Off
(S Drive 120,140,180A)
Motor Settings
Current Limit Max (Amps)
0
1
Latching
0
1
Latching
0
1
Latching
0
0
Max
100
100
100
100
General Settings
Soft Stop
Brake Time (milli-Seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Min
1
1
0
0
(S Drive II)
130
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Current Foldback Time (Seconds)
Current Foldback Level (%)
140
10
80
70
59
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Stall Timeout (Seconds)
660
30
10
0
Motor Compensation (milli-Ohms)
AntiRollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
25
12
0
1275
0
Braking Current Limit (Amps)
Timed Foldback Braking Current (Amps)
Timed Foldback Speed (%)
Enhanced Motor Compensation (Up) (%)
140
140
100
200
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive II Only)
Enhanced Motor Compensation (Down) (%)
Enhanced Motor Compensation (Up) Gain
170
85
(S Drive II Only)
(S Drive II Only)
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
Throttle Reference Test
ISO Test Resistor
Timed Throttle Invert
(S Drive II Only)
(S Drive II Only)
1
(0 = Single-ended, 1 = Wig-wag, 2 = Unipolar)
15
140
2
(0 = Drive, 1 = Inhibit, 2 = Trip)
On
Off
0
(0 = Off, 1 = Inhibit 2, 2 = Inhibit 3)
Trophy
Technical product information | 83
Trophy S-drive 140, 15 km/h, foot throttle original electronics (ID-no &lt; QT02400)
Speed Settings
Forward Acceleration (0.1 Seconds)
Forward Deceleration (0.1 Seconds)
Reverse Acceleration (0.1 Seconds)
Reverse Deceleration (0.1 Seconds)
Fast
35
13
40
25
Slow
30
12
40
15
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
100
10
40
5
On
50
30
30
30
Operation Settings
Sleep Timer (Minutes)
Throttle Invert
0
No
Battery Settings
Low Battery Flash Level (Bars)
Cable Resistance (milli-Ohms)
Calibration Factor
Low Battery Alarm
0
100
100
Off
Trucharge Reset Voltage (Deci-Volts)
(S Drive 180A) (S Drive II)
Battery Curve Scaler
(S Drive II Only)
250
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2 Speed (%)
Inihibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
Factory Settings
Acceleration (0.1 Seconds)
Deceleration (0.1 Seconds)
Forward Speed (%)
Reverse Speed (%)
Off
1400
24
0
(0 = Trucharge, 1 = LED, 2 = Analogue)
2
Off
Pulsed Reverse Alarm
Diagnostic Alarm
Off
Off
Brake Disconnected Alarm
Off
Brake Fault Detect
Brake Light
On
On
Push too Fast Threshold
Push too Fast Timeout
Freewheel Enable
Inhibit 2 Horn Input Enable
35
20
Disable
Off
(S Drive 120,140,180A)
Motor Settings
Current Limit Max (Amps)
0
1
Latching
0
1
Latching
0
1
Latching
0
0
Max
100
100
100
100
General Settings
Soft Stop
Brake Time (milli-Seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Min
1
1
0
0
(S Drive II)
130
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Current Foldback Time (Seconds)
Current Foldback Level (%)
140
10
80
70
59
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Stall Timeout (Seconds)
660
30
10
0
Motor Compensation (milli-Ohms)
AntiRollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
25
12
0
1275
0
Braking Current Limit (Amps)
Timed Foldback Braking Current (Amps)
Timed Foldback Speed (%)
Enhanced Motor Compensation (Up) (%)
140
140
100
200
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive II Only)
Enhanced Motor Compensation (Down) (%)
Enhanced Motor Compensation (Up) Gain
170
85
(S Drive II Only)
(S Drive II Only)
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
Throttle Reference Test
ISO Test Resistor
Timed Throttle Invert
(S Drive II Only)
(S Drive II Only)
0
(0 = Single-ended, 1 = Wig-wag, 2 = Unipolar)
15
180
2
(0 = Drive, 1 = Inhibit, 2 = Trip)
On
Off
0
(0 = Off, 1 = Inhibit 2, 2 = Inhibit 3)
84 | Technical product information
Trophy
Trophy S-drive 140 Alpine original electronics (ID-no &lt; QT02400)
Speed Settings
Forward Acceleration (0.1 Seconds)
Forward Deceleration (0.1 Seconds)
Reverse Acceleration (0.1 Seconds)
Reverse Deceleration (0.1 Seconds)
Fast
35
13
40
25
Slow
30
13
40
25
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
100
10
40
5
On
100
10
40
5
Operation Settings
Sleep Timer (Minutes)
Throttle Invert
0
Yes
Battery Settings
Low Battery Flash Level (Bars)
Cable Resistance (milli-Ohms)
Calibration Factor
Low Battery Alarm
0
100
100
Off
Trucharge Reset Voltage (Deci-Volts)
(S Drive 180A) (S Drive II)
Battery Curve Scaler
(S Drive II Only)
250
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2 Speed (%)
Inihibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
Factory Settings
Acceleration (0.1 Seconds)
Deceleration (0.1 Seconds)
Forward Speed (%)
Reverse Speed (%)
On
1500
24
0
(0 = Trucharge, 1 = LED, 2 = Analogue)
2
Off
Pulsed Reverse Alarm
Diagnostic Alarm
Off
Off
Brake Disconnected Alarm
Off
Brake Fault Detect
Brake Light
On
On
Push too Fast Threshold
Push too Fast Timeout
Freewheel Enable
Inhibit 2 Horn Input Enable
35
20
Disable
Off
(S Drive 120,140,180A)
Motor Settings
Current Limit Max (Amps)
0
1
Latching
0
1
Latching
0
1
Latching
0
1
Max
100
100
100
100
General Settings
Soft Stop
Brake Time (milli-Seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Min
1
1
0
0
(S Drive II)
130
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Current Foldback Time (Seconds)
Current Foldback Level (%)
130
10
80
70
59
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Stall Timeout (Seconds)
660
30
10
0
Motor Compensation (milli-Ohms)
AntiRollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
35
12
0
650
0
Braking Current Limit (Amps)
Timed Foldback Braking Current (Amps)
Timed Foldback Speed (%)
Enhanced Motor Compensation (Up) (%)
140
140
100
180
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive II Only)
Enhanced Motor Compensation (Down) (%)
Enhanced Motor Compensation (Up) Gain
190
50
(S Drive II Only)
(S Drive II Only)
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
Throttle Reference Test
ISO Test Resistor
Timed Throttle Invert
(S Drive II Only)
(S Drive II Only)
1
(0 = Single-ended, 1 = Wig-wag, 2 = Unipolar)
15
140
2
(0 = Drive, 1 = Inhibit, 2 = Trip)
On
Off
0
(0 = Off, 1 = Inhibit 2, 2 = Inhibit 3)
Trophy
Technical product information | 85
Trophy S-drive 140 Alpine, foot throttle original electronics (ID-no &lt; QT02400)
Speed Settings
Forward Acceleration (0.1 Seconds)
Forward Deceleration (0.1 Seconds)
Reverse Acceleration (0.1 Seconds)
Reverse Deceleration (0.1 Seconds)
Fast
35
13
40
25
Slow
30
13
40
25
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
100
10
40
5
On
100
10
40
5
Operation Settings
Sleep Timer (Minutes)
Throttle Invert
0
Yes
Battery Settings
Low Battery Flash Level (Bars)
Cable Resistance (milli-Ohms)
Calibration Factor
Low Battery Alarm
0
100
100
Off
Trucharge Reset Voltage (Deci-Volts)
(S Drive 180A) (S Drive II)
Battery Curve Scaler
(S Drive II Only)
250
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2 Speed (%)
Inihibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
Factory Settings
Acceleration (0.1 Seconds)
Deceleration (0.1 Seconds)
Forward Speed (%)
Reverse Speed (%)
On
1500
24
0
(0 = Trucharge, 1 = LED, 2 = Analogue)
2
Off
Pulsed Reverse Alarm
Diagnostic Alarm
Off
Off
Brake Disconnected Alarm
Off
Brake Fault Detect
Brake Light
On
On
Push too Fast Threshold
Push too Fast Timeout
Freewheel Enable
Inhibit 2 Horn Input Enable
35
20
Disable
Off
(S Drive 120,140,180A)
Motor Settings
Current Limit Max (Amps)
0
1
Latching
0
1
Latching
0
1
Latching
0
1
Max
100
100
100
100
General Settings
Soft Stop
Brake Time (milli-Seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Min
1
1
0
0
(S Drive II)
130
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Current Foldback Time (Seconds)
Current Foldback Level (%)
130
10
80
70
59
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Stall Timeout (Seconds)
660
30
10
0
Motor Compensation (milli-Ohms)
AntiRollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
35
12
0
650
0
Braking Current Limit (Amps)
Timed Foldback Braking Current (Amps)
Timed Foldback Speed (%)
Enhanced Motor Compensation (Up) (%)
140
140
100
180
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive II Only)
Enhanced Motor Compensation (Down) (%)
Enhanced Motor Compensation (Up) Gain
190
50
(S Drive II Only)
(S Drive II Only)
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
Throttle Reference Test
ISO Test Resistor
Timed Throttle Invert
(S Drive II Only)
(S Drive II Only)
0
(0 = Single-ended, 1 = Wig-wag, 2 = Unipolar)
15
180
2
(0 = Drive, 1 = Inhibit, 2 = Trip)
On
Off
0
(0 = Off, 1 = Inhibit 2, 2 = Inhibit 3)
86 | Technical product information
Trophy
Trophy S-drive 140 Alpine advanced electronics (ID-no &gt; QT02400)
Speed Settings
Forward Acceleration (0.1 Seconds)
Forward Deceleration (0.1 Seconds)
Reverse Acceleration (0.1 Seconds)
Reverse Deceleration (0.1 Seconds)
Fast
35
13
40
25
Slow
30
13
40
25
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
100
10
40
5
On
100
10
40
5
Operation Settings
Sleep Timer (Minutes)
Throttle Invert
0
Yes
Battery Settings
Low Battery Flash Level (Bars)
Cable Resistance (milli-Ohms)
Calibration Factor
Low Battery Alarm
0
100
100
Off
Trucharge Reset Voltage (Deci-Volts)
(S Drive 180A) (S Drive II)
Battery Curve Scaler
(S Drive II Only)
250
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2 Speed (%)
Inihibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
Factory Settings
Acceleration (0.1 Seconds)
Deceleration (0.1 Seconds)
Forward Speed (%)
Reverse Speed (%)
On
1500
24
0
(0 = Trucharge, 1 = LED, 2 = Analogue)
2
Off
Pulsed Reverse Alarm
Diagnostic Alarm
Off
Off
Brake Disconnected Alarm
Off
Brake Fault Detect
Brake Light
On
Off
Push too Fast Threshold
Push too Fast Timeout
Freewheel Enable
Inhibit 2 Horn Input Enable
35
20
Disable
Off
(S Drive 120,140,180A)
Motor Settings
Current Limit Max (Amps)
0
1
Latching
0
1
Latching
0
1
Non-Latching
0
1
Max
100
100
100
100
General Settings
Soft Stop
Brake Time (milli-Seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Min
1
1
0
0
(S Drive II)
130
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Current Foldback Time (Seconds)
Current Foldback Level (%)
130
10
80
70
59
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Stall Timeout (Seconds)
660
30
10
0
Motor Compensation (milli-Ohms)
AntiRollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
35
12
0
650
0
Braking Current Limit (Amps)
Timed Foldback Braking Current (Amps)
Timed Foldback Speed (%)
Enhanced Motor Compensation (Up) (%)
140
140
100
180
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive II Only)
Enhanced Motor Compensation (Down) (%)
Enhanced Motor Compensation (Up) Gain
190
50
(S Drive II Only)
(S Drive II Only)
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
Throttle Reference Test
ISO Test Resistor
Timed Throttle Invert
(S Drive II Only)
(S Drive II Only)
1
(0 = Single-ended, 1 = Wig-wag, 2 = Unipolar)
15
140
2
(0 = Drive, 1 = Inhibit, 2 = Trip)
On
Off
0
(0 = Off, 1 = Inhibit 2, 2 = Inhibit 3)
Trophy
Technical product information | 87
Trophy S-drive 140, 15 km/h CT original electronics (ID-no &lt; QT02400)
Speed Settings
Forward Acceleration (0.1 Seconds)
Forward Deceleration (0.1 Seconds)
Reverse Acceleration (0.1 Seconds)
Reverse Deceleration (0.1 Seconds)
Fast
35
13
40
25
Slow
35
13
40
25
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
100
10
40
5
On
100
10
40
5
Operation Settings
Sleep Timer (Minutes)
Throttle Invert
0
Yes
Battery Settings
Low Battery Flash Level (Bars)
Cable Resistance (milli-Ohms)
Calibration Factor
Low Battery Alarm
0
100
100
Off
Trucharge Reset Voltage (Deci-Volts)
(S Drive 180A) (S Drive II)
Battery Curve Scaler
(S Drive II Only)
250
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2 Speed (%)
Inihibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
Factory Settings
Acceleration (0.1 Seconds)
Deceleration (0.1 Seconds)
Forward Speed (%)
Reverse Speed (%)
On
1500
24
0
(0 = Trucharge, 1 = LED, 2 = Analogue)
2
Off
Pulsed Reverse Alarm
Diagnostic Alarm
Off
Off
Brake Disconnected Alarm
Off
Brake Fault Detect
Brake Light
On
On
Push too Fast Threshold
Push too Fast Timeout
Freewheel Enable
Inhibit 2 Horn Input Enable
35
20
Disable
Off
(S Drive 120,140,180A)
Motor Settings
Current Limit Max (Amps)
0
1
Latching
0
1
Latching
0
1
Non-Latching
0
0
Max
100
100
100
100
General Settings
Soft Stop
Brake Time (milli-Seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Min
1
1
0
0
(S Drive II)
130
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Current Foldback Time (Seconds)
Current Foldback Level (%)
140
10
80
70
59
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Stall Timeout (Seconds)
660
30
10
0
Motor Compensation (milli-Ohms)
AntiRollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
25
12
0
900
0
Braking Current Limit (Amps)
Timed Foldback Braking Current (Amps)
Timed Foldback Speed (%)
Enhanced Motor Compensation (Up) (%)
140
140
100
180
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive II Only)
Enhanced Motor Compensation (Down) (%)
Enhanced Motor Compensation (Up) Gain
170
75
(S Drive II Only)
(S Drive II Only)
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
Throttle Reference Test
ISO Test Resistor
Timed Throttle Invert
(S Drive II Only)
(S Drive II Only)
1
(0 = Single-ended, 1 = Wig-wag, 2 = Unipolar)
15
140
2
(0 = Drive, 1 = Inhibit, 2 = Trip)
On
Off
0
(0 = Off, 1 = Inhibit 2, 2 = Inhibit 3)
88 | Technical product information
Trophy
Trophy S-drive 140, 15 km/h CT, foot throttle original electronics (ID-no &lt; QT02400)
Speed Settings
Forward Acceleration (0.1 Seconds)
Forward Deceleration (0.1 Seconds)
Reverse Acceleration (0.1 Seconds)
Reverse Deceleration (0.1 Seconds)
Fast
35
13
40
25
Slow
35
13
40
25
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
100
10
40
5
On
100
10
40
5
Operation Settings
Sleep Timer (Minutes)
Throttle Invert
0
Yes
Battery Settings
Low Battery Flash Level (Bars)
Cable Resistance (milli-Ohms)
Calibration Factor
Low Battery Alarm
0
100
100
Off
Trucharge Reset Voltage (Deci-Volts)
(S Drive 180A) (S Drive II)
Battery Curve Scaler
(S Drive II Only)
250
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2 Speed (%)
Inihibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
Factory Settings
Acceleration (0.1 Seconds)
Deceleration (0.1 Seconds)
Forward Speed (%)
Reverse Speed (%)
On
1500
24
0
(0 = Trucharge, 1 = LED, 2 = Analogue)
2
Off
Pulsed Reverse Alarm
Diagnostic Alarm
Off
Off
Brake Disconnected Alarm
Off
Brake Fault Detect
Brake Light
On
On
Push too Fast Threshold
Push too Fast Timeout
Freewheel Enable
Inhibit 2 Horn Input Enable
35
20
Disable
Off
(S Drive 120,140,180A)
Motor Settings
Current Limit Max (Amps)
0
1
Latching
0
1
Latching
0
1
Non-Latching
0
0
Max
100
100
100
100
General Settings
Soft Stop
Brake Time (milli-Seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Min
1
1
0
0
(S Drive II)
130
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Current Foldback Time (Seconds)
Current Foldback Level (%)
140
10
80
70
59
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Stall Timeout (Seconds)
660
30
10
0
Motor Compensation (milli-Ohms)
AntiRollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
25
12
0
900
0
Braking Current Limit (Amps)
Timed Foldback Braking Current (Amps)
Timed Foldback Speed (%)
Enhanced Motor Compensation (Up) (%)
140
140
100
180
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive II Only)
Enhanced Motor Compensation (Down) (%)
Enhanced Motor Compensation (Up) Gain
170
75
(S Drive II Only)
(S Drive II Only)
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
Throttle Reference Test
ISO Test Resistor
Timed Throttle Invert
(S Drive II Only)
(S Drive II Only)
0
(0 = Single-ended, 1 = Wig-wag, 2 = Unipolar)
15
180
2
(0 = Drive, 1 = Inhibit, 2 = Trip)
On
Off
0
(0 = Off, 1 = Inhibit 2, 2 = Inhibit 3)
Trophy
Trophy S-drive 140, 15 km/h CT advanced electronics (ID-no &gt; QT02400)
Speed Settings
Forward Acceleration (0.1 Seconds)
Forward Deceleration (0.1 Seconds)
Reverse Acceleration (0.1 Seconds)
Reverse Deceleration (0.1 Seconds)
Fast
35
13
40
25
Slow
35
13
40
25
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
100
10
40
5
On
100
10
40
5
Operation Settings
Sleep Timer (Minutes)
Throttle Invert
0
Yes
Battery Settings
Low Battery Flash Level (Bars)
Cable Resistance (milli-Ohms)
Calibration Factor
Low Battery Alarm
0
50
100
Off
Trucharge Reset Voltage (Deci-Volts)
(S Drive 180A) (S Drive II)
Battery Curve Scaler
(S Drive II Only)
250
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2 Speed (%)
Inihibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
Factory Settings
Acceleration (0.1 Seconds)
Deceleration (0.1 Seconds)
Forward Speed (%)
Reverse Speed (%)
On
1000
24
0
(0 = Trucharge, 1 = LED, 2 = Analogue)
2
Off
Pulsed Reverse Alarm
Diagnostic Alarm
Off
Off
Brake Disconnected Alarm
Off
Brake Fault Detect
Brake Light
On
Off
Push too Fast Threshold
Push too Fast Timeout
Freewheel Enable
Inhibit 2 Horn Input Enable
35
20
Disable
Off
(S Drive 120,140,180A)
Motor Settings
Current Limit Max (Amps)
0
1
Latching
0
1
Latching
0
1
Non-Latching
0
1
Max
100
100
100
100
General Settings
Soft Stop
Brake Time (milli-Seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Min
1
1
0
0
(S Drive II)
130
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Current Foldback Time (Seconds)
Current Foldback Level (%)
140
10
80
70
59
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Stall Timeout (Seconds)
660
30
10
0
Motor Compensation (milli-Ohms)
AntiRollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
25
12
0
900
0
Braking Current Limit (Amps)
Timed Foldback Braking Current (Amps)
Timed Foldback Speed (%)
Enhanced Motor Compensation (Up) (%)
140
140
100
200
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive Only)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive 180A) (S Drive II)
(S Drive II Only)
Enhanced Motor Compensation (Down) (%)
Enhanced Motor Compensation (Up) Gain
170
75
(S Drive II Only)
(S Drive II Only)
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
Throttle Reference Test
ISO Test Resistor
Timed Throttle Invert
(S Drive II Only)
(S Drive II Only)
1
(0 = Single-ended, 1 = Wig-wag, 2 = Unipolar)
15
140
2
(0 = Drive, 1 = Inhibit, 2 = Trip)
On
Off
0
(0 = Off, 1 = Inhibit 2, 2 = Inhibit 3)
90 | Technical product information
7.7 Electrical diagram Trophy Egis
Trophy
Trophy
7.8 Electrical diagram Trophy S-Drive
Original electronics (ID-no &lt; QT02400)
Technical product information | 91
92 | Technical product information
Advanced electronics (ID-no &gt; QT02400)
Trophy
Trophy
Technical product information | 93
7.9 Service information transaxles
Summary
End of 2008 Handicare has published the product update &quot;Trophy with S-Drive Controller&quot;. Among other things, this update
mentioned the new sturdier transaxles for Trophy with Egis controller and for Trophy with S-Drive controller. Since the benefits of
these new transaxles remained underexposed in the load of information in the news item, we will explain here the improvements
to the transaxle and summarise service instructions for these parts.
The new transaxles (Egis or S/Drive configuration) offer improved bearing and bearing position. New, bigger motor brushes
also contribute to extend the life expectancy of the parts and reduces costs of ownership.
Regular preventative service checks are important to verify the condition of the parts and enables to replace them at the right
time. See service instructions.
Description
The new transaxles (standard and heavy duty / Egis and S-Drive compatible) as presented in our Product News item &quot;Trophy
with S-Drive Controller&quot; dated 10/09/2008 offer improved performance and life expectancy. This is due to the improved bearing
and bearing position but also to some changes that were made to reduce wear of the commutator and brushes. This way service
costs are reduced.
The new transaxles are equipped with bigger motor brushes. As a consequence the current density (Amps/mm2) in the
commutator and brushes drops and this improves the life span of these parts. The effect is more pronounced in the Trophy Egis
because this controller uses higher currents than the S-Drive controller.
Regular preventative service checks are important to verify the condition of the parts and enables to replace them at the right
time. Therefore see the service check instructions.
Service checks instructions
Check if dimensions of commutator and motor brushes satisfy minimum dimensions as indicated in the illustrations, accordingly
to the table below.
Part
Commutator
Motor brush
Trophy with Egis controller and
Schmid transaxle
Once every 3 years
At least once a year or every 1000 km
Trophy with S-Drive controller and
Schmid or CT transaxle
Once every 3 years
At least once a year or every 3000 km
Clean the collector on the anchor of the motor with pressed air from dust.
Commutator Schmid
Dimensions:
• minimum 35,4mm.
Egis controller and Schmid
transaxle
Dimensions:
• maximum(17,5mm)
• minimum(9mm)
S-Drive controller and
Schmid or CT transaxle
Dimensions Schmid:
• maximum(16mm)
• minimum(8mm)
Dimensions CT:
• maximum (18mm)
• minimum (8mm)
17,5
16/18
9
8
94 | Warranty
8
Trophy
Warranty
8.1 Definitions of terms
Definitions of terms used in this warranty:
• Consumable part: Part that is subjected to natural wear and tear or natural contamination during normal operation within the
lifetime of the product (section 9 of Handicare’s general terms and conditions of sale);
• Client: Those who purchase the product directly from Handicare;
• Corrective action: Repair, replace or refund of the product;
• Dealer: Those who re-sell the product to the User;
• Defect: Any circumstance due to which the product is not sound or fit to use, caused by a lack of quality of the material used to
manufacture the product as well as the quality of the manufacturing process;
• Option: An accessory delivered by Handicare to extend the standard product model;
• Product: Product that is delivered according to brochure or contract (e.g. wheelchair, scooter, battery-charger etc.);
• Part: Part of product that can be exchanged or replaced. This can be an option, accessory, service part or consumable part;
• Returns: Product or part that needs to be returned;
• RMA-process: Process to return goods, contact Handicare’s Customer Service;
• Service part: Part that is durable and may be subjected to natural wear and tear or natural contamination during normal
operation within the lifetime of the product.;
• User: Those who use the product;
• Warranty: The rights and obligations set forth in this document;
• Warranty period: The period of time during which the warranty is valid;
• Warranty provider: Handicare B.V., Vossenbeemd 104, 5705 CL Helmond, The Netherlands.
Notwithstanding the rights and obligations of Handicare, Client and User set forth in Handicare’s general terms and conditions
of sale, the rights of the Client and/or User towards Handicare in case of defects are limited to the provisions set forth in this
warranty. For the duration of the warranty period Handicare guarantees that the product is without defects.
In case of any defects the User is required –within two weeks after discovery of the defect- to contact the dealer. He has to
complete a return form and return the product or part via the RMA-process. Handicare will, at its sole discretion, take the
corrective action it seems fit under the given circumstances within a reasonable period of time (depends on nature of claim) from
receipt of the completed return form. The warranty period will not be extended after a corrective action.
8.2 Warranty period table
Power wheelchairs / scooters
Description
Warranty period
Examples include, but are not limited to the parts mentioned
below
Frame
2 years
Weldment/frame
Drive system
1 year
Transaxle, motor, motor brake
Electronics
1 year
Controller, controlling mechanism, wiring harness, electronic
components
Service Parts
New: 1 year after invoice
Repaired: 90 days after invoice
Brakes
Consumable parts
40 days after invoice
Wheels, push handles etc.
Options/Accessories
2 years
Mirror, mudguards etc.
Not being service part or consumable part.
Handicare will only accept shipment costs and corrective costs related to warranty on equipment during the warranty period.
This warranty will void in case of:
• The product and/or its parts being modified or items having been added by others than Handicare;
• Changes in cosmetic appearance by use;
• Failure to observe the instructions for use and maintenance, use other than normal use, wear and tear, negligence, collateral
damage by neglect of earlier symptoms, overloading, third-party accidents, non-original parts used and defects not caused by
the product;
• Circumstances beyond our control (flood, fire, etc.).
This warranty does not cover:
• Tyres and inner tubes
• Batteries (covered by the battery manufacturer’s warranty).
Clients and/or Users have legal (statutory) rights under applicable national laws relating to the sale of consumer products. This
warranty does not affect statutory rights you may have nor those rights that cannot be excluded or limited, nor rights against the
entity from whom the product was purchased. Clients may assert any rights they have at their sole discretion.
Trophy
| 95
Version Page
2012 V3
5
11
19
22
24
27
28
29/30
30-31
32-67
68
73
76-85
82 / 85
88
89
2013 V1
12
Draw
Changes
Transfered entire manual in new lay-out (comparable with Trophy 20)
Textual changes in Introduction
Updated table of content (added drawing number 5b, 6b and 10b)
05b Added exploded view and spare part list Console, printed circuit board and throttle control
according electronics ID-no &gt; QT02400
06b Added exploded view and spare part list Wiring, electronics and batteries according electronics
ID-no &gt; QT02400
08+09 Changed position 11 (9000543) in 11a and 11b, 900543 Indicator 12V (ID-no &lt; QT02400) and
9007552 Indicator 24V (&gt; QT02400)
10b Added exploded view and spare part list Cabling according electronics ID-no &gt; QT02400
4.3 Added article numbers 9007569 and 9007499 according electronics ID-no &gt; QT02400
Added 'annual inspection' table
Textual changes in chapter 5
Added service instructions
5.5 Added paragraph 5.5 Display menu settings
7.2 Updated specifications
Changed S-Drive settings into Mk.
Added controller settings tables according electronics ID-no &gt; QT02400
7.7 Added electrical diagram according electronics ID-no &gt; QT02400
7.8 Added service information S-drive controller ID no &gt; QT02400 transaxles
1
•
•
•
•
•
13
2
•
•
•
•
15
3
•
•
•
•
•
•
24
8
•
•
•
•
25
9
•
•
•
•
•
•
Changed article number position 1 into 9003907
Changed description of article number 9000178
Changed description of article number 9000542
Changed position and description of article numbers 9000584 and 9001994 and added position
20c (article number 9004159)
Changed position and description of article number 15010.4200 and added position 21b (article
number 9004161)
Changed one position number 2 into 24 and added into the part list
Changed description of article number 9000542
Changed position and description of article number 9001815 and added position 18b (article
number 9004511)
Changed position and description of article number 15010.4200 and added position 19b (article
number 9004161)
Added article number 1015444 Motorbrake cover Schmid
Changed position and description of article numbers 9000550, 9001996 and 1015104 and
added position 5d and 5e (article numbers 9007719 and 9007723)
Changed position and description of article numbers 9001172, 9001998 and 1015154 and
added position 6d and 6e (article numbers 9007717 and 9007721)
Changed position and description of article numbers 9000549, 9001955 and 1015103 and
added position 7d and 7e (article numbers 9007720 and 9007724)
Changed position and description of article numbers 9001173, 9001997 and 1015153 and
added position 8d and 8e (article numbers 9007718 and 9007722)
Changed position and description of article number 9000548 and added position 9b, 9c and 9d
(article numbers 1015102, 9007716 and 9007725)
Changed position and description of article number 1001905 and added position 1b and 1c
(article numbers 1015765 and 1015770)
Changed position and description of article number 1007754 and added position 2b and 2c
(article numbers 1015760 and 1015761)
Changed position and description of article number 1001895 and added position 9b and 9c
(article numbers 1015766 and 1015771)
Changed position and description of article number 1001899 and added position 12b and 12c
(article numbers 1015767 and 1015772)
Changed position and description of article number 1001905 and added position 1b and 1c
(article numbers 1015765 and 1015770)
Changed position and description of article number 1007754 and added position 2b and 2c
(article numbers 1015760 and 1015761)
Changed position and description of article number 1001895 and added position 9b and 9c
(article numbers 1015766 and 1015771)
Changed position and description of article number 1001899 and added position 12b and 12c
(article numbers 1015767 and 1015772)
Changed position and description of article number 9001963 and added position 17b and 17c
(article numbers 1015768 and 1015773)
Changed position and description of article number 9001964 and added position 18b and 18c
(article numbers 1015769 and 1015774)
96 |
Version
2014 V1
Trophy
Page
26-27
28
32-66
Draw Changes
10a+b Changed article number 9000773 into 99117
4.3 Changed article number 9000701 into 1015545
Updated several service instructions
13
2
14
3
17
5a
19
5b
20
6a
21
6b
23
8
23-26
25
8+9
9
27
10a
28
10b
29
4.3
58
70
77
81-88
2015-V1
12
1
13
2
14
3
16
4
• Changed description of acticle numbers 9002090, 9002091, 9001795 and 9001801 (added
'grey')
• Added article numbers 9003406, 9003408, 9004458 and 9004459
• Added mounting material
• Added article number 1353 and 1001817
Added 'for original electronics' to drawing name and 'for original electronics (ID-no &lt; QT02400)' to
the original specific options
• Added 'for advanced electronics' to drawing name and 'for advanced electronics (ID-no &gt;
QT02400)' to the advanced specific options
• Changed article numbers positions 11 and 28: 9007572, 9007374, 9007373 and 9007372 into
9008789, 9008791, 9008790 and 1016535
Added 'for original electronics' to drawing name and 'for original electronics (ID-no &lt; QT02400)' to
the original specific options
• Added 'for advanced electronics' to drawing name and 'for advanced electronics (ID-no &gt;
QT02400)' to the advanced specific options
• Changed article number position 7: 9004430 into 9008778
• Added position 7 to drawing
• Added article numbers 1015775, 1015776, 1015777 and 1015762 Platinum white metallic
covers
• Added article numbers 1015780, 1015781, 1015782 and 1015763 Graphic black metallic covers
• Updated drawing
Changed naming of the Ruby red covers in Red covers
• Added article numbers 1015775, 1015776, 1015777, 1015762, 1015778 and 1015779 Platinum
white metallic covers
• Added article numbers 1015780, 1015781, 1015782, 1015763, 1015783 and 1015784 Graphic
black metallic covers
• Updated drawing
• Added 'for original electronics' to drawing name and 'for original electronics (ID-no &lt; QT02400)'
to the original specific options
• Changed description of article numbers 9000786, 9002449 and 9004029 ('added with charge
socket')
• Added 'for advanced electronics' to drawing name and 'for advanced electronics (ID-no &gt;
QT02400)' to the advanced specific options
• Changed description of article number 9004029 (added 'with charge socket')
• Added position 7: article number 1015507 Lap strap with roll-up for Master Seat
• Updated drawing (added Lap strap, updated drawing of Front bag and adapted sort order of
images)
Changed article numbers: 9007572, 9007374 and 9007373 into 9008789, 9008791 and 9008790
• Changed article numbers 9007372, 9007572, 9007374 and 9007373 into 1016535, 9008789,
9008790 and 9008791
• Updated 'expand controller options' table
• Changed max. battery capacity C20 88 Ah into 86 Ah
• Added chapter 7.3 Driving programs
Added 'for original / advanced electronics' to desciptions ID-no PBxxxxx only / QBxxxxx onwards
Updated Electronic settings
• Changed description article number 00000.5306
• Deleted article number 9000584 (position 20a), no longer available
• Changed article numbers 15010.4200, 9004161 and 15010.4100 into 1015112, 1015113 and
1015118
• Added article number 00000.5500
• Changed article numbers 15010.4200, 9004161, 15010.4100 and 00000.4312 into 1015112,
1015113, 1015118 and 9002155
• Deleted article number 00000.2003
• Changed description 1011585, 9000603 and 9000683
• Changed article number 1005956,9000548 and 9000547 into 1012527, 1015114 and 1015119
• Deleted article number 1004272
• Added article number 103.00091.000, 00000.3715, 9002221, 00000.2003 and 00000.1702
• Updated drawing
• Changed article number 00000.4312 into 9008687
• Changed description 9001135
Trophy
Version
| 97
Page
17
Draw
5a
19
5b
20
6a
22
7
23
8
25
9
27
29
10a
4.3
71
94
Changes
• Changed Qty and description article number 9002792
• Added article number 1002343
• Updated drawing
• Changed article number 1001730 into 9002792 'Screw Ejot K30x6'
• Added article numbers 1016928, 1016930 and 1016929
• Deleted article numbers 00355.4203 (2x) and 00355.4213 (position 2, 3 and 4)
• Changed description article numbers 9002457 and 1012504
• Added article numbers 1002241, 1008392, 1002392, 232.00011.000, 237.00011.000, 1001806,
1002394 and 1008411
• Deleted article number 1007756 (position 7)
• Changed article numbers 9000460 and 9000461 into 1009947 and 1009946 and changed
description
• Added article number 9000426, 1012522 and 00000.1503
• Deleted article number 1007756
• Added article numbers 9000426, 1012522 and 00000.1503
Changed description article number 9004431
• Added article numbers 1017464, 1017458, 1017459, 1017460 and 1017461 Colour exchange
sets for 3-wheel Trophy
• Added article numbers 1017463, 1017415, 1017416, 1017417 and 1017418 Colour exchange
sets for 4-wheel Trophy
• Added article numbers 4930, 1001813, 1001814, A810, 1003095, 1003097, 1002421, 4824,
1001752, 1001753 and 1015595
Updated spare part matrix for electronic upgrade
Updated warranty text
">
Hello! I've reviewed the Handicare Trophy service manual. I can assist with questions about repairs, maintenance, spare parts, troubleshooting, technical specifications, and warranty information for this mobility scooter. Feel free to ask!
Show related prompts
Assistant typing
Assistant terminated
Key Features

Customizable seating and controls for tailored comfort
Powerful motor and long battery range for extended journeys
Advanced suspension system for a smooth and stable ride
Comprehensive lighting system for enhanced visibility and safety
Easy-to-use controls and intuitive display for effortless operation
Durable construction and weather resistance for reliable performance
Frequently Answers and Questions

What type of terrain is the TROPHY suitable for?

The TROPHY is designed to handle various terrains, including indoor surfaces, paved roads, and uneven outdoor paths.
How long does the battery last on a single charge?

The battery range varies depending on factors such as user weight, speed, and terrain, but typically allows for several hours of continuous use.
Can the TROPHY be used in wet weather?

Yes, the TROPHY is weather-resistant and can be used in light rain or snow conditions.
Key Features

Frequently Answers and Questions

What type of terrain is the TROPHY suitable for?

How long does the battery last on a single charge?

Can the TROPHY be used in wet weather?

Related

Handicare TROPHY Service manual

Handicare Trophy 20 User Manual

Trophy 20 User Manual - Handicare

Handicare Trophy 3W, Trophy 4W, Trophy Alpine User Manual

Handicare TROPHY User manual

Handicare Fortress 2000 SERIES Owner's Manual

Handicare TROPHY 20 Service Manual - Online & Download

Handicare Winner User manual

Mobility Scooter Trophy Service Manual

Handicare TROPHY Service Manual - TROPHY Scooters

Superlight SL-3 Maintenance Instruction

Trophy 20 Mobility Scooter Service Manual
