Programming Step 2
[ Y
PWR
PGM STATUS a Mn
o ©
Depress the button marked “РОМ” on the Martec
Access Products HomeLink® Compatible Default
Receiver. This will cause the “STATUS” LED on
the receiver to light. You now have 30 seconds to
complete step 3.
Programming Step 3
Depress the HomeLink® Universal Transceiver
button that you have selected to control the
opener: continue holding until the “STATUS”
LED on the receiver goes “OFF”. You now have
30 seconds to complete step 4. Г
Programming Step 4
Depress the same HomeLink® Universal
Transceiver button a second time and hold until
“STATUS” LED on the receiver starts to flash.
The default rolling code format is now installed.
Your installation is now complete.
NOTE: To install additional HomeLink® Universal
Transceiver buttons follow Programming Steps 2, 3,
and 4 for each button.
Ifa seventh HomeLink® Universal Transceiver
button is installed into the Martec Access Products
HomeLink® Compatible Default Receiver, the first
button installed will be pushed out. All buttons are
treated on a “first in”, “first out” basis after six
individual buttons have been installed.
Depress the Martec Access Products HomeLink®
Compatible Default Receiver Program button for 10
seconds to erase all transceiver codes stored in
memory.
| device is subject to the following conditions: (1) This
This device complies with FCC Rules Part 15 and IC
Canada Rules and Regulations. Operation of this
device may not cause harmful interference; (2) This
device must accept any interference that may be
received, including interference that may cause
undesired operation; (3) Changes or modifications not
expressly approved by the manufacturer, could void
the authority of users to operate this equipment.
MARTEC ACCESS PRODUCTS
LIMITED WARRANTY
This product is warranted to the original user against
defects in material and workmanship for one year from
- the date of purchase. Warrantor will repair or replace, at
its option, any device found to require service under this
Warranty. The repaired or replaced device will be
returned to the customer at the warrantors cost. Call
1-800-483-2539 for instructions on how to proceed with
a warranty claim. The user will pay the cost of returning
the device to the warrantor for service. This warranty is
void if the failure of the device is determined to have
been caused by improper installation or use, abuse, fire,
water, or acts of God. This warranty excludes all other
warranties, expressed or implied, including any warranty
of merchantability. Martec Access Products shall not be
liable for consequential or incidental damages that may
arise from any defect or failure of the radio control
device. Some states do not allow the exclusion or
limitation of consequential or incidental damages. This
limitation is not valid in jurisdictions, which do not allow
limitation of incidental or consequential damages or
limitation of warranty periods. This warranty gives you
specific legal rights, and you may also have other rights
that vary from state to state.
HomeLink® is a registered trademark of Johnson
Controls, Inc., Holland, Michigan.
MARTEC
Martec Access Products Inc.
240 Sheffield Street, Mountainside, NJ 07092
008 233 0691 m FAX 908 233 5766
www.martecaccess.com
MDN-199 rev-A
j
| Martec Access Products
| tHomeLink’
Compatible Default Receiver Kit
Receiver
INSTALLATION & PROGRAMMING
INSTRUCTIONS
| The Martec Access Products HomeLink®
| Compatible Default Receiver is intended for
the control of garage door and gate openers
that do not have HomeLink compatible radio
receivers. The default receiver can be used to
| program up to six HomeLink transceiver:
' buttons. The power is supplied to the receiver
| by a 24 volt plug-in transformer. A two-wire
' harness is supplied for connecting the relay
| output from the default receiver to the radio
- A A ee |
be necessary to make the connections to the
push button terminals on the opener.
A WARNING
| Radio Controls are prohibited from providing
constant contact closure when installed
| on the push button inputs of residential
garage door openers that are provided with
monitored safety systems.
MARTEC
Martec Access Products Inc.
240 Sheffield Street, Mountainside, NJ 07092
908 233 0691 m FAX 908 233 5766
www.martecaccess.com
À WARNING
DO NOT ALLOW CHILDREN TO PLAY
WITH OR OPERATE REMOTE CONTROL
TRANSMITTERS. The garage door could
close and cause serious injury or death.
WARNING
Disconnect power from opener
before installing receiver
Step 2A. Connect Receiver
Step 1. Mount the Receiver.
TO AVOID INTERFERENCE FROM
UNWANTED”CROSS TALK” MOUNT
THE HomeLink® COMPATIBLE
RECEIVER AS FAR AWAY AS POSSIBLE
FROM ANY OPENER THAT HAS A
BUILT-IN RADIO RECEIVER.
Mount the Martec
Access Products
HomeLink® .
Compatible Default
Receiver as far from the
existing opener as
possible, but within
reach of the wire
connecting the power
transformer and the wire
going to the opener
terminals.
Step 2.
Wiring PGM STATUS RELAY
Receiver oe, © @
to Opener
Plug the two
white wire
harness into
the receiver
output terminal
marked
“RELAY”.
into the Receiver.
to Opener
Connect the two white wire harness to the
appropriate terminals on the opener.
(See opener instructions, in some cases
it will be necessary to make these output
connections to the push button terminals on
the opener).
Step 3. Plug the 24 Volt
Power Transformer Lead
Plug the power transformer lead into the receiver
output terminal marked “PWR”.
Step 4. Plug the Power Transformer into a 115 VAC Receptacle.
Reconnect power to the opener and proceed to programming.
PROGRAMMING
A
NOTE: The Martec Access Products HomeLink® Compatible Default Receiver can be programmed before it
is mounted and connected to the opener. Simply plug the power transformer into a convenient receptacle or
extension cord, connect the 24 volt power transformer lead to the receiver, and proceed with the Programming
Instructions. After programming, unplug the transformer from the temporary power source and move the
receiver and power transformer to their permanent locations. Connect the white wire harness from the receiver
to the push button or radio control terminals.
Programming Step 1
Enable the HomeLink® Universal Transceiver to transmit the default code by
simultaneously holding the three push buttons down for 20 seconds until the
transceiver LED changes from solid “On” to flashing “On and Off”. Continue to
hold the buttons down for approximately 10 additional seconds until the transceiver
LED stops flashing and goes out. The HomeLink® Universal Transceiver is now in
the default rolling code format.
CAUTION
The opener may operate unexpectedly as you are
programming your remote controls.
(continued)
">
