DV-AGMD-101599.9 AGMD Spray Gun (Draft 5-17-06).pmd

SERVICE MANUAL
DV
-AGMD-101599.9
DV-AGMD-101599.9
(Replaces DV-AGMD-101599.8)
AGMD HIGH PERFORMANCE
AUT
OMA
TIC SPRA
Y GUN
AUTOMA
OMATIC
SPRAY
MODELS:
TOMIZA
TION
514 CONVENTIONAL AIR A
AT
OMIZATION
515 HVLP A
TOMIZA
TION
AT
OMIZATION
IMPOR
TANT
IMPORT
ANT:: Before using this equipment,
carefully read SAFETY PRECAUTIONS,
starting on page 1, and all instructions in
this manual. Keep this Service Manual for
future reference.
Service Manual Price: $30.00 (U.S.)
N O T E : This manual was published to supercede Service Manual DV-AGMD-101599.8 to
revision DV-AGMD-101599.9. Reasons for this change are noted under “Manual Change
Summary” inside the back cover of this manual.
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Contents
CONTENTS
SAFETY:
PAGE
1-3
SAFETY PRECAUTIONS............................................................................................................ 1
HAZARDS / SAFEGUARDS........................................................................................................ 2-3
INTRODUCTION:
5-6
GENERAL DESCRIPTION.......................................................................................................... 5
MODELS....................................................................................................................................... 5
SPECIFICATIONS....................................................................................................................... 5
AGMD HIGH PERFORMANCE AUTOMATIC
SPRAY GUN MODEL IDENTIFICATION................................................................................... 6
INSTALLATION:
7
INSTALLATION............................................................................................................................ 7
OPERATION:
9
AIR CAP INSTALLATION............................................................................................................ 9
AGMD-515 HVLP & LVMP ONLY............................................................................................... 9
BACK PRESSURE - 46C AND 83C............................................................................................ 9
MAINTENANCE:
11
GUN REMOVAL AND INSTALLATION.......................................................................................11
PARTS IDENTIFICATION:
13-25
AGMD PARTS IDENTIFICATION OVERVIEW.......................................................................... 13
AGMD-514 CONVENTIONAL ATOMIZATION SPRAY GUN
PARTS IDENTIFICATION / PARTS LIST................................................................................... 15-16
AGMD-515 HVLP AND LVMP ATOMIZATION SPRAY GUN
PARTS IDENTIFICATION / PARTS LIST................................................................................... 17-18
AGMD-514 CONVENTIONAL AUTOMATIC GUN &
AGMD-515 HVLP AND LVMP AUTOMATIC GUN FLUID TIP,
NEEDLE COMBINATIONS, AIR CAP SELECTION &
AIR FLOW CHARTS ................................................................................................................... 19
AGMD-245-1 INTERMEDIATE PLATE
ASSEMBLY / PARTS LIST......................................................................................................... 20
AGMD-251 MACHINE ADAPTER ASSEMBLY /
PARTS LIST................................................................................................................................. 21
(Continued On Next Page)
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Contents
CONTENTS(Cont.)
PAGE
PARTS IDENTIFICATION (Cont.):
13-25
AGMD-279-US60 AND AGMD-279-US90 SINGLE HEAD
ADAPTER VIEWS / PARTS LIST............................................................................................... 22
AGMD-278-US60 AND AGMD-278-US90 DUAL HEAD
ADAPTER VIEWS / PARTS LIST............................................................................................... 23
AGMD-514 AND AGMD-515 RECOMMENDED
SPARE PARTS / AIR CAP TEST KITS (OPTIONAL)............................................................... 24
ACCESSORIES........................................................................................................................... 25
WARRANTY POLICIES:
27
LIMITED WARRANTY................................................................................................................. 27
APPENDIX:
28-31
PAINT AND SOLVENT SPECIFICATIONS............................................................................... 28
VISCOSITY CONVERSION CHART......................................................................................... 29-30
VOLUMETRIC CONTENT OF HOSE OR TUBE...................................................................... 31
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Contents
NOTES
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Safety
SAFETY
SAFETY PRECAUTIONS
Before operating, maintaining or servicing any
ITW Finishing system, read and understand all of
the technical and safety literature. This manual
contains information that is important for you to
know and understand. This information relates to
USER SAFETY and PREVENTING EQUIPMENT
PROBLEMS. To help you recognize this
information, we use the following symbols. Please
pay particular attention to these sections.
A WARNING! states information to alert you
to a situation that might cause serious injury
if instructions are not followed.
A CAUTION! states information that tells
how to prevent damage to equipment or how
to avoid a situation that might cause minor
injury.
A NOTE is information relevant to the
procedure in progress.
While this manual lists standard specifications
and service procedures, some minor deviations
may be found between this literature and your
equipment. Differences in local codes and plant
requirements, material delivery requirements, etc.,
make such variations inevitable. Compare this
manual with your system installation drawings
and appropriate ITW equipment manuals to
reconcile such differences.
!
WARNING
The user MUST read and be familiar
with the Safety Section in this manual and
the ITW DeVilbiss safety literature therein
identified.
>
> This manual MUST be read and thoroughly understood by ALL personnel who
operate, clean or maintain this equipment!
Special care should be taken to ensure that
the WARNINGS and safety requirements
for operating and servicing the equipment
are followed. The user should be aware of
and adhere to ALL local building and fire
codes and ordinances as well as NFPA33 SAFETY STANDARD prior to installing, operating, and/or servicing this equipment.
!
WARNING
> The hazards shown on the following page
may occur during the normal use of this
equipment. Please read the hazard chart
beginning on page 2.
Careful study and continued use of this manual will
provide a better understanding of the equipment
and process, resulting in more efficient operation,
longer trouble-free service and faster, easier
troubleshooting. If you do not have the manuals
and safety literature for your DeVilbiss system,
contact your local ITW Industrial representative or
ITW Automotive Finishing Group.
1
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Safety
AREA
HAZARD
SAFEGUARDS
Tells where hazards
Tells what the hazard is.
Tells how to avoid the hazard.
Fire Hazard
Fire extinguishing equipment must be present in the
spray area and tested periodically.
may occur.
Spray Area
Improper or inadequate operation
and maintenance procedures will Spray areas must be kept clean to prevent the
accumulation of combustible residues.
cause a fire hazard.
Smoking must never be allowed in the spray area.
When using solvents for cleaning:
Those used for equipment flushing should have flash
points equal to or higher than those of the coating
material.
Those used for general cleaning must have flash
points above 100oF (37.8oC).
Spray booth ventilation must be kept at the rates
required by NFPA-33, OSHA, and local codes. In
addition, ventilation must be maintained during
cleaning operations using flammable or combustible
solvents.
The paint process and equipment should be set up
and operated in accordance with NFPA -33, NEC,
and OSHA requirements.
General Use and
Maintenance
Improper operation or maintenance Personnel must be given training in accordance with the
may create a hazard.
requirements of NFPA-33.
Personnel must be properly trained Instructions and safety precautions must be read and
in the use of this equipment.
understood prior to using this equipment.
Comply with appropriate local, state, and national codes
governing ventilation, fire protection, operation
maintenance, and housekeeping. Reference OSHA,
NFPA-33, and your insurance company requirements.
DV-AGMD-101599.9
2
AGMD Automatic Spray Gun - Safety
AREA
HAZARD
SAFEGUARDS
Tells where hazards
Tells what the hazard is.
Tells how to avoid the hazard.
Explosion
Hazard/
Incompatible
Materials
Halogenated hydrocarbon solvents
for example: methylene chloride
and 1,1,1,-Trichloroethane are not
chemically compatible with the
aluminum that might be used in
many system components. The
chemical reaction caused by these
solvents reacting with aluminum
can become violent and lead to an
equipment explosion.
Aluminum is widely used in other spray application
equipment - such as material pumps, regulators,
triggering valves, etc. Halogenated hydrocarbon
solvents must never be used with aluminum
equipment during spraying, flushing, or cleaning.
Read the label or data sheet for the material you
intend to spray. If in doubt as to whether or not a
coating or cleaning material is compatible, contact
your material supplier. Any other type of solvent
may be used with aluminum equipment.
Toxic Substances
Certain material may be harmful if Follow the requirements of the Material Safety Data
inhaled, or if there is contact with Sheet supplied by coating material manufacturer.
the skin.
Adequate exhaust must be provided to keep the air
free of accumulations of toxic materials.
may occur.
Use a mask or respirator whenever there is a chance
of inhaling sprayed materials. The mask must be
compatible with the material being sprayed and its
concentration. Equipment must be as prescribed by
an industrial hygienist or safety expert, and be
NIOSH approved.
3
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Safety
NOTES
DV-AGMD-101599.9
4
AGMD Automatic Spray Gun - Introduction
INTRODUCTION
GENERAL DESCRIPTION
SPECIFICA
TIONS
SPECIFICATIONS
The AGMD High Performance Automatic
Spray Gun is suitable for use with solvent base
and waterborne materials.
Mechanical / Physical
When using this gun with highly corrosive or highly
abrasive materials it must be expected that the
necessity for replacement of parts will be increased.
If there is any doubt about the suitability of the gun
for a particular material ask the paint manufacturer.
The AGMD automatic spray gun will be mounted
to the gun mover by means of an intermediate
plate and an adapter. The patented locking device
on the intermediate plate provides a simple and
quick change without tools (example: for servicing
purposes). The installation with the quick locking
device provides precise repositioning.
The air cap can be installed with indexing of 90o.
MODELS
AGMD-514: Automatic gun for conventional air
atomization, including air cap indexing.
Weight:
1.33 lbs. (603 g)
Dimensions:
(See Figure 1)
Max. Pressure:
130 psi (9 bar)
(Atomizing Air (ATOM) &
Fan Air (FAN))
200 psi (14 bar)
(Material (MAT))
100 psi (7 bar)
(Cylinder Air (CYL))
Spray Head:
300 Grade Stainless Steel
Fluid Tip:
(Standard)
300 Grade Stainless Steel
Fluid Needle:
(Standard)
300 Grade Stainless Steel
Material Contacting
Seals:
Viton (Waterborne
(Standard):
Materials)
Kalrez (Solvent Base
(Optional):
Materials)
AGMD-515: Automatic gun for "HVLP" and
"LVMP" atomization, including air cap indexing.
Specify air cap and fluid tip combinations when
ordering (see "Table 1a and 1b" in the "Parts
Identification" section).
5
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Introduction
1.81”
(46mm)
2.16”
(55mm)
4.96”
(126mm)
514/515
1.73”
(44mm)
Figure 1:
AGMD-514/515 Dimensions (With AGMD-245-1 Intermediate Plate)
AGMD HIGH PERFORMANCE AUT
OMA
TIC
AUTOMA
OMATIC
SPRA
Y GUN MODEL IDENTIFICA
TION *
SPRAY
IDENTIFICATION
When ordering, use AGMD-514 U, FF, or 797C as indicated. Three digits must follow the basic part
number, for example:
AGMD - 514 U 797C FF
Gun Model/
Type/Series
With Circulation = U
Without Circulation = Without U
DV-AGMD-101599.9
Tip Size (e.g. FF = .055)
Air Cap (see "Table 1a and 1b)
6
AGMD Automatic Spray Gun - Installation
INSTALLATION
1. Firmly screw intermediate plate to adapter
and screw adapter to gun mover (robot / reciprocator).
2. Connect compressed air hose and fluid hose
machined adapter.
7
CYL Air:
1/8” ID (3.2mm) min.
75 psi min.
FAN Air:
(Conventional & HVLP)
Hose lengths up to 15’ (457m)
1/4” ID (6.3mm) min.
.
ATOM Air:
(Conventional & HVLP)
Hose lengths up to 15’ (457m)
1/4” ID min.
Fluid:
1/8” ID (3.2mm) min.
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Installation
NOTES
DV-AGMD-101599.9
8
AGMD Automatic Spray Gun - Operation
OPERATION
Connect compressed air and fluid supply to
suitable pressure regulator. For consistent
operation the air pressure should be regulated
and be free from oil mist and water condensate.
When securing the gun to the intermediate plate
care must be taken that all o-rings are in place.
Lightly apply a small amount of petroleum jelly to
the o-ring surfaces.
AIR CAP INST
ALLA
TION
INSTALLA
ALLATION
Figure 2:
Indexing Pin Locations
(Refer to Figure 2)
NOTE
1. The air cap positioning depends upon the baffle
position. Fit the baffle first on the gun body as
shown in Figure 2.
NOTE
> Position 1: Horizontal Pattern
> For HVLP operation (max. 10 psi, -0.7
bar cap pressure), DO NOT exceed the
air inlet pressure given as follows:
PSI (bar)
25 (1.7)
25 (1.7)
22 (1.5)
CAP #
46C
83C
122C
> Position 2: Vertical Pattern
2. Tighten the tip to maintain the baffle in position.
3. Place the air cap by using the two indexes on
the baffle.
4. Fix the air cap by screwing the retaining ring.
AGMD-515 HVLP AND
Y
LVMP ONL
ONLY
BACK PRESSURE 46C AND 83C
Due to the unique cone shape of the MP fluid tips
(nozzle), a slight back pressure is created against
the fluid column. This will reduce the amount of
fluid output. To compensate, increase the fluid
regulator pressure slightly if necessary. With 10
psi (0.7 bar) cap pressure, back pressures are
approximately 3.5 psi (0.24 bar) with the 46C.
All models are designed to provide maximum
transfer efficiency by limiting air cap pressure to
10 psi (0.7 bar) (in the U.S., this complies with
rules issued by SCAQMD and other air qulity
authorities). Air cap pressure can be measured
with an optional air cap test kit. (See "Spare
Parts " in the "Parts Identification" section.)
9
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Operation
NOTES
DV-AGMD-101599.9
10
AGMD Automatic Spray Gun - Maintenance
MAINTENANCE
GUN REMOV
AL AND
REMOVAL
INST
ALLA
TION
INSTALLA
ALLATION
NOTES
1. Relieve system pressure.
2. Press unlocking pin, turn gun by 45o and lift it
off the intermediate plate.
3. When installing gun, check o-rings and replace
if necessary. Check for clean surface and holes.
Lubricate o-rings and AGMD-245-1 intermediate
plate with food grade petroleum jelly before installation.
11
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Maintenance
NOTES
DV-AGMD-101599.9
12
AGMD Automatic Spray Gun - Parts Identification
PARTS IDENTIFICATION
Conventional AGMD-514
HVLP AGMD-515
Intermediate Plate
AGMD-245-1
MACHINE ADAPTER
AGMD-251
90° SINGLE ADAPTER
AGMD-279-US90
90° DOUBLE ADAPTER
AGMD-278-US90
60° DOUBLE ADAPTER
AGMD-278-US60
60° SINGLE ADAPTER
AGMD-279-US60
AGMD-278-S SLEEVE INCLUDED WITH ADAPTERS
Figure 3:
13
AGMD Parts Identification Overview
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Parts Identification
NOTES
DV-AGMD-101599.9
14
AGMD Automatic Spray Gun - Parts Identification
Figure 4:
15
AGMD-514 Conventional Atomization Spray Gun Parts Identification
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Parts Identification
AGMD-514 CONVENTIONAL A
T OMIZA
TION SPRA
Y GUN
AT
OMIZATION
SPRAY
PAR
TS LIST - (Figure 4)
ARTS
Description
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Retaining Ring
Air Cap
Fluid Tip (1/2" Hex)
Gasket (2 Required)
Baffle Assembly (Includes two (2) AGMD-65-1 Gaskets)
Spray Head
Locking Device
Screw, Socket Head Cap (4mm Hex)
Needle Packing Assembly (6mm Hex)
Fluid Needle
O-Ring (Two (2) Required)
Gun Body
Piston
Spring
Plate, Rear
Screw, Set with Slot
Screw, Spring Plunger
Screw (4 Required), Hex Head Machined (5mm Hex)
O-Ring (5 Required), Standard Waterborne Materials
O-Ring (5 Required), Optional, Solventborne Materials
Pad, Spring
Pressure Spring
DV-AGMD-101599.9
Part #
MBC-368
able 1a
Table
See T
See T
able 1a
Table
AGMD-65-1
AGMD-33
AGMD-195
AGMD-244-1
AGMD-130
AGMD-405-1
See T
able 1a
Table
7554-09
AGMD-217
AGMD-243-1
AGMD-111
AGMD-242
AGMD-116
AGMD-115
AGMD-131
AGMD-119
79001-27
AGMD-219
AGMD-110
16
AGMD Automatic Spray Gun - Parts Identification
Figure 5:
17
AGMD-515 HVLP & LVMP Atomization Spray Gun Parts Identification
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Parts Identification
AGMD-515 HVLP AND L
TOMIZA
TION SPRA
Y GUN
LVMP
AT
OMIZATION
SPRAY
VMP A
PAR
TS LIST - (Figure 5)
ARTS
Description
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Retaining Ring
Air Cap
Fluid Tip (1/2" Hex)
Gasket (2 Required)
Baffle Assembly (Includes two (2) AGMD-65-1 Gaskets)
Spray Head
Locking Device
Screw, Socket Head Cap (4mm Hex)
Needle Packing Assembly (6mm Hex)
Fluid Needle
O-Ring (2 Required)
Gun Body
Piston
Spring
Plate, Rear
Screw, Set with Slot
Screw, Spring Plunger
Screw (4 Required), Hex Head Machined (5mm Hex)
O-Ring (5 Required), Standard Waterborne Materials
O-Ring (5 Required), Optional, Solventborne Materials
Pad, Spring
Pressure Spring
DV-AGMD-101599.9
Part #
MBC-368
able 1b
Table
See T
See T
able 1b
Table
AGMD-65-1
AGMD-34
AGMD-195
AGMD-244-1
AGMD-130
AGMD-405-1
See T
able 1b
Table
7554-09
AGMD-217
AGMD-243-1
AGMD-111
AGMD-242
AGMD-116
AGMD-115
AGMD-131
AGMD-119
79001-27
AGMD-219
AGMD-110
18
AGMD Automatic Spray Gun - Parts Identification
AGMD-514 CONVENTIONAL AUT
OMA
TIC GUN AUTOMA
OMATIC
Fluid T
ip and Needle Combinations, Air Cap Selection, and
Tip
Air Flow
Air Cap
Part # †
Fluid Tip & Needle‡ Viscosity Flow Rate Fan Width
Air Flow
Inch @ 10"
CC/min.
CFM @ psi AGMD-4000-XX ø in. ZAHN #2
Target
(seconds)
Inlet Pressure
AV-1239-765C
AV-1239-765C
AV-1239-765C
AV-1239-797C
AV-1239-797C
AV-1239-797C
22 @ 80
22 @ 80
22 @ 80
21 @ 70
21 @ 70
21 @ 70
FX / .042
FX / .055
E / .070
FX / .042
FF / .055
E / .070
Up to 26
Up to 28
28+
Up to 26
Up to 28
28+
Up to 600
Up to 900
Up to 1000
Up to 600
Up to 900
Up to 1000
15"
15"
15"
17"
17"
17"
† Certified air caps marked with "C"
‡ Made of High Grade 303 Stainless Steel
Table 1a:
AGMD-514 Conventional Automatic Gun Fluid Tip and Needle Combinations
AGMD-515 HVLP AND L
VMP AUT
OMA
TIC GUN LVMP
AUTOMA
OMATIC
Fluid T
ip and Needle Combinations, Air Cap Selection, and
Tip
Air Flow
Air Cap
Part # †
†
AGMD-46C
AGMD-46C
†
AGMD-122C
†
AGMD-122C
AGMD-83
†
Fluid Tip & Needle‡ Viscosity Flow Rate Fan Width
Air Flow
CC/min.
Inch @ 10"
CFM @ psi AGMD-4600-XX ø in. ZAHN #2
(seconds)
Target
Inlet Pressure
26.5 @ 70
26.5 @ 70
9.5 @ 22
9.5 @ 22
28.5 @ 70
FX / .042
FX / .055
FX / .042
FF / .055
E / .070
Up to 26
Up to 30
Up to 26
Up to 30
Up to 34
Up to 200
Up to 300
Up to 200
Up to 300
Up to 450
11"
11"
10"
10"
12"
† Certified air caps marked with "C"
‡ Made of High Grade 303 Stainless Steel
Table 1b:
19
AGMD-515 HVLP & LVMP Fluid Tip and Needle Combinations
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Parts Identification
Figure 7:
AGMD-245-1 Intermediate Plate Assembly Parts Identification
AGMD-245-1 INTERMEDIA
TE ASSEMBL
Y
INTERMEDIATE
PLATE
ASSEMBLY
TE PLA
PAR
TS LIST - (Figure 7)
ARTS
Item #
1
2
3
4
5
6
7
Description
Intermediate Plate
Wear Plate
Pressure Piece
Plate
Screw, Socket Pan Head Machined
Screw, (3 Required), Socket Head Cap
O-Ring, (5 Required), Waterborne
O-Ring, (5 Required), Solventborne Materials
DV-AGMD-101599.9
Part #
AGMD-147-1
AGMD-346
AGMD-247
AGMD-246
AGMD-130
AGMD-142
AGMD-119
79001-27
20
AGMD Automatic Spray Gun - Parts Identification
Figure 8:
AGMD-251 Machine Adapter Assembly Parts Identification
AGMD-251 MACHINE ADAPTER ASSEMBL
Y
ASSEMBLY
PAR
ARTS
TS LIST - (Figure 8)
Item #
1
2
3
5
Description
Adapter
Connector Assembly, Push-In Tubing, 6mm OD
Connector Assembly, Push-In Tubing, 5/16” OD
Screw, Set
Part #
Qty.
AGMD-151a
AGMD-126
AGMD-127
AGMD-117
1
1
2
1
* ZZ-2663 - Fluid Connector Assembly, Push-In Tubing, 5/16" OD X .040 Wall (2)
are not included with kit. May be purchased separately. Contact your ITW
Finishing representative or customer service.
21
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Parts Identification
PAINT
OUT
(1/4”AN)
PAINT IN
(1/4”AN)
FAN
(1/4”NPT)
ATOM
(1/4”NPT)
TRIGGER
1
(1/8”NPT)
Figure 9a:
Single Head Adapter Robot
(Bottom View)
Figure 9b: AGMD-279-US60 Single Head
Adapter Parts Identification (Top View)
AGMD-279-US60 SINGLE HEAD ADAPTER FOR
ROBOT P
AR
TS LIST - (Figures 9a & 9b)
PAR
ARTS
Item #
1
2
3
Description
Part #
O
Adapter - 60 Face Angle
Screw, (6 Required), Socket Head Cap
Sleeve (Included with adapter)
AGMD-279-US60
AGMD-142
AGMD-278-S
PAINT
OUT
(1/4”AN)
PAINT IN
(1/4”AN)
FAN
(1/4”NPT)
ATOM
(1/4”NPT)
TRIGGER
1
(1/8”NPT)
Figure 10a:
Single Head Robot Adapter
(Bottom View)
Figure 10b: AGMD-279-US90 Single Head
Adapter Parts Identification (Top View)
AGMD-279-US90 SINGLE HEAD ADAPTER FOR
ROBOT P
AR
TS LIST - (Figures 10a & 10b)
PAR
ARTS
Item #
1
2
3
Description
O
Adapter - 90 Face Angle
Screw, (6 Required), Socket Head Cap
Sleeve (Included with adapter)
DV-AGMD-101599.9
Part #
AGMD-279-US90
AGMD-142
AGMD-278-S
22
AGMD Automatic Spray Gun - Parts Identification
PAINT IN 2 PAINT IN 1
(1/4”AN)
(1/4”AN)
FAN 1
(1/4”NPT)
ATOM 2
(1/4”NPT)
TRIGGER 1
(1/8”NPT)
TRIGGER 2
(1/8"NPT)
FAN 2
(1/4”NPT)
Figure 11a:
ATOM 1
(1/4”NPT)
Dual Head Adapter Robot
(Bottom View)
Figure 11b: AGMD-278-US60 Dual Head
Adapter Parts Identification (Top View)
AGMD-278-US60 DUAL HEAD ADAPTER FOR
ROBOT P
AR
TS LIST - (Figures 1
1a & 1
1b)
PAR
ARTS
11a
11b)
Item #
Description
Part #
Adapter - 60O Face Angle
Screw (4 Required), Socket Head Cap
Sleeve (Included with adapter)
1
2
3
PAINT IN 2
(1/4”AN)
AGMD-278-US60
AGMD-142
AGMD-278-S
PAINT IN 1
(1/4”AN)
FAN 1
(1/4”NPT)
ATOM 2
(1/4”NPT)
TRIGGER 2
(1/8”NPT)
TRIGGER 1
(1/8”NPT)
FAN 2
( 1 / 4 ” N P T ) ATOM 1
(1/4”NPT)
Figure 12a:
Dual Head Adapter Robot
(Bottom View)
Figure 12b: AGMD-278-US90 Dual Head
Adapter Parts Identification (Top View)
AGMD-278-US90 DUAL HEAD ADAPTER FOR
ROBOT P
AR
TS LIST - (Figures 12a & 12b)
PAR
ARTS
Item #
1
2
3
23
Description
O
Adapter - 90 Face Angle
Screw (4 Required), Socket Head Cap
Sleeve (Included with adapter)
Part #
AGMD-278-US90
AGMD-142
AGMD-278-S
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Parts Identification
AGMD-514 AND AGMD-515 RECOMMENDED SP
ARE P
AR
TS
SPARE
PAR
ARTS
Description
Part #
AGMD-110
AGMD-111
AGMD-65-1
AGMD-244-1
AGMD-130
AGMD-405-1
7554-09
AGMD-243-1
79001-27
AGMD-119
MBC-368
Pressure Spring
Pressure Spring
Fluid Tip Gasket
Locking Device
Cap Screw
Needle Packing
O-Ring
Piston Assembly
O-Ring, Solvent Proof, Kalrez
(Optional)
O-Ring, Viton (Standard)
Retaining Ring
Number of Guns
1-5
5-10 10-15 15+
1
1
4
1
1
2
1
1
5
1
1
6
2
2
3
2
2
10
2
2
8
3
3
4
3
3
15
3
3
10
4
4
5
4
4
20
5
1
10
2
15
3
20
4
Notes
For use with solventborne
materials.
For use with waterborne paints.
AGMD-514 RECOMMENDED SP
ARE P
AR
TS
SPARE
PAR
ARTS
Part #
AGMD-33
AGMD-4000-XX
AV-1239-XXXC
Description
Baffle Assembly
Fluid Tip & Needle
Combination
Air Cap
Number of Guns
1-5
5-10 10-15 15+
1
2
1
3
2
4
2
4
2
3
4
5
Notes
Replace XX with FX for .042,
FF for .055, or E for .070
Replace XXX with 765 or 797.
AGMD-515 RECOMMENDED SP
ARE P
AR
TS
SPARE
PAR
ARTS
Part #
AGMD-34
AGMD-4600-XX
AGMD-XXXX
Description
Baffle Assembly
Fluid Tip & Needle
Combination
Air Cap
Number of Guns
1-5
5-10 10-15 15+
1
2
1
3
2
4
2
5
2
3
4
5
Notes
Replace XX with FX for .042;
FF for .055 and E for .070.
Replace XXX with 46, 122 or 83.
AGMD-514 AND 515 AIR CAP TEST KITS (OPTIONAL)
Part #
78293-01
74035-18
74035-19
74035-20
78293-02
DV-AGMD-101599.9
Description
Air Cap Test Kit
Air Cap Calibrator Kit
Air Cap Calibrator Kit
Air Cap Calibrator Kit
Air Cap Test Kit
Number of Guns
1-5
5-10
10-15 15+
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Notes
For 46C Cap
For 765C Cap
For 797C Cap
For 122C Cap
For 83 Cap
24
AGMD Automatic Spray Gun - Parts Identification
ACCESSORIES (INDUSTRIAL)
Part #
Description
54-380 Gun Mounting Bar Bracket. (For reciprocator or fixed rod mounting) (Binks)
54-3691 Gun Cover (Package of 20)
Gun Mounting Bar Bracket
25
Gun Cover
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Parts Identification
NOTES
DV-AGMD-101599.9
26
AGMD Automatic Spray Gun - Warranty Policies
WARRANTY POLICIES
LIMITED ONE (1) YEAR
WARRANTY FOR
COA
TING EQUIPMENT
COATING
PRODUCTS
All merchandise manufactured by ITW DeVilbiss
is warranted to be free of defects in workmanship
and material. The terms of the warranty, except as
hereinafter provided, extend for a period of one (1)
year from date of first purchase at retail by user
excluding equipment failures which are the result
of misapplication, misues, incorrect maintenance,
or normal wear. If after inspection by us, defect is
confirmed, we will at our option repair, replace, or
issue credit, minus allowance for usage received.
Merchandise of a size suitable for shipping will be
sent to a point designated by DeVilbiss at
purchaser's expense; larger or fixed merchandise
will be inspected at the site. If claimed defect is
reported to DeVilbiss within the 1 year from date of
purchase, and if the merchandise is actaully
defective, DeVilbiss will provide all necessary
replacement parts.
There is no other express warranty. Implied
warranties, including those of merchantability and fitness for a particular purpose,
are limited to one year from purchase and to
the extent permitted by law any and all
implied warranties are excluded. This is the
exclusive remedy and liability for consequential damages under any and all warranties
are excluded to the extent exclusion is
permitted by law. Some states do not allow
limitations on how long an implied warranty
lasts, or the limitation or exclusion of
consequential or incidental damages, so the
above limitation or exclusion may not apply
to you.
27
This warranty gives you specific legal rights, and
you may also have other rights which vary from
state to state.
This Warranty Does NOT Cover:
A. Merchandise that has become inoperative
because of ordinary wear, misuse, negligence,
accident, or improper and unauthorized repair
or alteration.
B. Costs occassioned by removal, replacement,
or repair of merchandise (other than by
DeVilbiss), without previous written authorization.
C. Merchandise sold by us which has been
manufactured by and identified as the product
of another company.
D. Repair costs of merchandise determined not to
be defective.
Warranty Instructions
In the event of malfunction, first ensure that the
equipment is the correct equipment to do the job
required, is properly installed and adjusted, and is
correctly maintained and operated. Then, if a
claim is made that DeVilbiss equipment or a part
there of does not operate properly, contact (1)
Your DeVilbiss Authorized Sales Outlet through
which the equipment was purchased, or (2) consult
your local directory for the phone number of the
DeVilbiss distributor nearest to you.
General
All decisions of DeVilbiss with regard to this policy
shall be final. DeVilbiss will not be responsible for
any material returned claimed defective other than
in accord with this statement of policy.
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Appendix
APPENDIX
PAINT AND SOL
VENT SPECIFICA
TIONS
SOLVENT
SPECIFICATIONS
RECOMMENDED VISCOSITY USING A ZAHN NO. 2
PAINT ELECTRICAL RESISTANCE**
RECOMMENDED DELIVERY (UP TO)
R E A TM
VECTOR™
EFM TM
E v o l v e r TM
18 TO 30 SEC
.1 MΩ TO ∞
1000 cc/min
REM TM / M90 TM NO. 2 HAND GUN TURBODISK T M
18 TO 30 SEC
20 TO 60 SEC
20 TO 60 SEC
.1 MΩ TO ∞
.1 TO 1 MΩ
.1 MΩ TO ∞
1500 cc/min
180 cc/min
1000 cc/min
AEROBELL ® II***
AEROBELL®
AEROBELL ® 33
RMA-101 T M
20 TO 60 SEC
.1 MΩ TO ∞
500 cc/min
GUIDE T
O USABLE SOL
TO
SOLVENT
VENT SELECTION
Chemical
Name
Common
Name
Category
Methylene Chloride Chlorinated Solvents
DICHLOROMETHANE
Aliphatic Hydrocarbons
Naptha
VM & P NAPHTHA
Ketones
ACETONE
Esters
METHYL ACETATE
Aromatic Hydrocarbons
BENZENE
Esters
ETHYL ACETATE
Ketones
MEK
2-BUTANONE
Esters
ISO-PROPYL ACETATE
Alcohols
IPA
ISOPROPYL ALCOHOL
Ketones
MPK
2-PENTANONE
Alcohols
Methyl Alcohol
METHANOL
Esters
n-Propyl Acetate
PROPYL ACETATE
Aromatic Hydrocarbons
Toluene
TOLUOL
Ketones
MIBK
METHYL ISOBUTYL KETONE
Esters
ISOBUTYL ACETATE
Alcohols
Ethyl Alcohol
ETHANOL
BUTYL ACET
ATE
Esters
ACETA
ETHYLBENZENE
Aromatic Hydrocarbons
n-Propyl Alcohol
1-PROPANOL
Alcohols
sec.-Butyl Alcohol
2-BUTANOL
Alcohols
Xylene
XYLOL
Aromatic Hydrocarbons
AMYL ACETATE
Esters
iso-Butyl Alcohol
2-METHYLPROPANOL
Alcohols
METHYL AMYL ACETATE
Esters
MIAK
5-METHYL-2-HEXANONE
Ketones
n-Butyl Alcohol
1-BUTANOL
Alcohols
2-ETHOXYETHANOL
Glycol Ethers
MAK
2-HEPTANONE
Ketones
CYCLOHEXANONE
Ketones
SC#100
AROMATIC-100
Aromatic Hydrocarbons
DIBK
DIISOBUTYL KETONE
Ketones
Amyl Alcohol
1-PENTANOL
Alcohols
DIACETONE ALCOHOL
Ketones
Butyl Cellosolve
2-BUTOXYETHANOL
Glycol Ethers
CYCLOHEXANOL
Alcohols
SC#150
AROMATIC-150
Aromatic Hydrocarbons
AROMATIC-200
Aromatic Hydrocarbons
*CAS
Flash Point ††
Number
(TCC)
75-09-2
8030-30-6
65oF
67-64-1
-18oF
79-20-9
90oF
71-43-2
12oF
141-78-6
24oF
78-93-3
16oF
108-21-4
35oF
67-63-0
53oF
107-87-9
104oF
67-56-1
50oF
109-60-4
55oF
108-88-3
48oF
108-10-1
60oF
110-19-0
69oF
64-17-5
7 8 oF
123-86-4
100-41-4
64oF
74oF
71-23-8
78-92-2
72oF
1330-02-07
79oF
628-63-7
106oF
78-83-1
82oF
108-84-9
96oF
110-12-3
96oF
71-36-3
95oF
110-80-5
164oF
110-43-0
102oF
108-94-1
111oF
111oF
108-83-8
120oF
71-41-0
123-42-2
133oF
111-76-2
154oF
108-93-0
111oF
149oF
203oF
Evap.
Rate†
14.5
10
5.6
5.3
5.1
3.9
3.8
3.4
2.5
2.5
2.1
2.1
1.9
1.6
1.5
1.4
1.0
.89
.86
.81
.80
.67
.62
.50
.50
.43
.38
.40
.29
.20
.19
.15
.12
.07
.05
.004
.003
⇑F
A
S
T
E
R
S
L
O
W
E
R
⇓
Elec.
Res.**
HIGH
HIGH
LOW
LOW
HIGH
MEDIUM
MEDIUM
LOW
LOW
MEDIUM
LOW
LOW
HIGH
MEDIUM
LOW
LOW
LOW
HIGH
LOW
LOW
HIGH
MEDIUM
LOW
LOW
MEDIUM
LOW
LOW
MEDIUM
MEDIUM
HIGH
MEDIUM
LOW
LOW
LOW
LOW
HIGH
HIGH
* CAS Number: Chemical Abstract Service Number.
© 05/2006 Illinois Tool Works Inc. All rights reserved.
** Electrical Resistance using the ITW Ransburg Meter.
*** Solvent Base Configuration Only.
†
Information Obtained From: http://solvdb.ncms.org
††
The lowest temperature at which a volatile fluid will ignite.
Evaporation Rate is Based Upon Butyl Acetate Having a Rate of 1.0
NOTE: Chart provides resistance and control information that we feel is necessary when using ITW Automotive Finishing equipment.
DV-AGMD-101599.9
28
AGMD Automatic Spray Gun - Appendix
Din Cup 4
Sears
Craftsman Cup
Saybolt
Universal SSU
Gardner Lithographic
Krebs Unit
KU
Gardner Holdt Bubble
Ford Cup 4
Ford Cup 3
30
16
10
.15
15
30
12
25
8 A-3
80
34
17
11
Zahn 5
60
Zahn 4
5 A-4
Zahn 3
20
Zahn 2
11
Zahn 1
27
Fisher 2
DuPont
Parlin 10
10
Fisher 1
DuPont
Parlin 7
.1
Poise
29
Centipoise
VISCOSITY CONVERSION CHART
.2
20
32
13
30
15
12
10
100
37
18
12
.25
25
37
14
35
17
15
12 A-2
130
41
19
13
.3
30
43
15
39
18
19
14 A-1
160
44
20
14
.4
40
50
16
50
21
25
18
.5
50
57
17
24
29
22
.6
60
64
18
29
33
25
.7
70
20
33
36
28
.8
80
22
39
41
31
.9
90
23
44
45
32
1.0
100
25
50
50
34
1.2
120
30
62
58
1.4
140
32
66
1.6
160
1.8
2.0
2.2
210
52
22
19
15
30
260
60
24
20
16
33
320
68
27
21
18
35
370
30
23
21
37
430
34
24
23
38
480
37
10
26
25
D
40
530
41
12
10
27
27
41
E
43
580
49
14
11
31
31
45
F
46
690
58
16
13
34
34
37
50
G
48
790
66
18
14
38
38
180
41
54
50
900
74
20
16
40
43
200
45
58
H
52
1000
82
23
17
10
44
46
220
62
I
54
1100
25
18
11
51
2.4
240
65
J
56
1200
27
20
12
55
2.6
260
68
58
1280
30
21
13
58
2.8
280
70
K
59
1380
32
22
14
63
3.0
300
74
L
60
1475
34
24
15
68
3.2
320
M
1530
36
25
16
72
3.4
340
N
1630
39
26
17
76
3.6
360
O
62
1730
41
28
18
82
3.8
380
1850
43
29
19
86
4.0
400
P
64
1950
46
30
20
90
4.2
420
2050
48
32
21
95
4.4
440
Q
4.6
460
R
4.8
480
5.0
500
5.5
6.0
7.0
700
8.0
800
9.0
900
V
10.0 1000
W
A
B
C
000
2160
50
33
22
100
66
2270
52
34
23
104
67
2380
54
36
24
109
S
68
2480
57
37
25
112
550
T
69
2660
63
40
27
124
600
U
71
2900
68
44
30
135
74
3375
51
35
160
77
3380
58
40
172
81
4300
64
45
195
85
4600
49
218
11.0 1100
88
5200
55
12.0 1200
92
5620
59
00
0
DV-AGMD-101599.9
AGMD Automatic Spray Gun - Appendix
21.0
2100
9850
22.0
2200
10300
23.0
2300
24.0
2400
25.0
2500
30.0
3000
35.0
3500
40.0
4000
45.0
4500
50.0
5000
55.0
5500
60.0
6000
65.0
6500
30000
70.0
7000
32500
75.0
7500
35000
80.0
8000
37000
85.0
8500
39500
90.0
9000
41000
95.0
9500
100.0 10000
64
8500
Y
9000
103
Z
2
9400
105 10750
109 11200
114 11600
Z-1
121 14500
Z-2
3
129 16500
133 18500
136 21000
Z-3
23500
26000
Z-4
4
2800
43000
Z-5
5
46500
110.0 11000
51000
120.0 12000
55005
130.0 13000
60000
65000
140.0 14000
150.0 15000
Din Cup 4
2000
Sears
Craftsman Cup
20.0
Zahn 5
1900
Zahn 4
1800
19.0
Zahn 3
18.0
1
Zahn 2
8000
X
Zahn 1
Saybolt
Universal SSU
101
Gardner Holdt Bubble
1700
16.0
Ford Cup 4
7500
17.0
1500
Ford Cup 3
100
1400
15.0
Fisher 2
7000
1600
14.0
Fisher 1
6480
98
1300
DuPont
Parlin 10
96
13.0
DuPont
Parlin 7
6100
Centipoise
95
Poise
Gardner Lithographic
Krebs Unit
KU
VISCOSITY CONVERSION CHART (Continued)
Z-6
67500
160.0 16000
74000
170.0 17000
83500
180.0 18000
83500
190.0 19000
88000
200.0 20000
93000
300.0 30000
140000
Note: All viscosity comparisons are as accurate as possible with existing information.
Comparisons are made with a material having a specific gravity of 1.0.
© 05/2004 Illinois Tool Works Inc. All rights reserved.
DV-AGMD-101599.9
30
AGMD Automatic Spray Gun - Appendix
VOLUMETRIC CONTENT OF HOSE OR TUBE
(English Units)
Cross
Seaction
(sq. in.)
I.D.
(inches)
cc/ft.
1/8
2.4
.012
3/16
5.4
.028
1/4
9.7
.049
5/16
15.1
.077
3/8
21.7
.110
1/2
38.6
.196
Length
5ft. (60") 10ft. (120") 15ft. (180") 25ft. (300") 50ft. (600")
.003 gal.
.4 fl. oz.
.007 gal.
.9 fl. oz.
.013 gal.
1.6 fl. oz.
.020 gal.
2.5 fl. oz.
.029 gal.
3.7 fl. oz.
.051 gal.
6.5 fl. oz.
.006 gal.
.8 fl. oz.
.014 gal.
1.8 fl. oz.
.025 gal.
3.3 fl. oz.
.040 gal.
5.1 fl. oz.
.057 gal.
7.3 fl. oz.
.102 gal.
13.1 fl. oz.
.010 gal.
1.2 fl. oz.
.022 gal.
2.8 fl. oz.
.038 gal.
4.9 fl. oz.
.060 gal.
7.6 fl. oz.
.086 gal.
11.0 fl. oz.
.153 gal.
19.6 fl. oz.
.016 gal.
2.0 fl. oz.
.036 gal.
4.6 fl. oz.
.064 gal.
8.2 fl. oz.
.100 gal.
12.7 fl. oz.
.143 gal.
18.4 fl. oz.
.255 gal.
32.6 fl. oz.
.032 gal.
4.1 fl. oz.
.072 gal.
9.2 fl. oz.
.127 gal.
16.3 fl. oz.
.199 gal.
25.5 fl. oz.
.287 gal.
36.7 fl. oz.
.510 gal.
65.3 fl. oz.
VOLUMETRIC CONTENT OF HOSE OR TUBE
(Metric Units)
Cross
Section
(mm 2 )
1.5m
3.0m
4.5m
6.0m
7.5m
10.2
10.2
15.3 cc
30.5 cc
45.8 cc
61.1 cc
76.3 cc
5.6
24.6
24.6
36.9 cc
73.9 cc
110.8 cc
147.8 cc
184.7 cc
6.8
36.3
36.3
54.5 cc
109.0 cc
163.4 cc
217.9 cc
272.4 cc
8.8
60.8
60.8
91.2 cc
182.5 cc
273.7 cc
364.9 cc
456.2 cc
I.D.
(mm)
cc/m
3.6
Length
© 05/2004 Illinois Tool Works Inc. All rights reserved.
31
DV-AGMD-101599.9
MANUAL CHANGE SUMMAR
Y
SUMMARY
This manual was published to supercede
Service Manual DV-AGMD-101599.8
DV-AGMD-101599.8,
AGMD Automatic Spray Gun, to make the
following changes:
1. Revised "Safety" section - removed sections
not pertaining to the AGMD High Performance
Automatic Spray Gun.
2. Revised "Specifications" in the "Introduction"
section - removed Baffle, Air Cap, and Air Cap
Retaining Ring specifications.
3. Revised "AGMD High Performance
Automatic Spray Gun Model Identification
(AGMD-514-U-797C-FF)" in the "Introduction"
section.
4. Revised "AGMD-245-1 Intermediate Plate
Assembly Parts List" in the "Parts Identification"
section - Item 7 description.
5. Added "Accessories and Figures" in the
"Parts Identification" section.
6. Added "Warranty Policies" for ITW Industrial
Finishing.
7. Added "Contact Information" on the "Back
Cover" for ITW Industrial Finishing and ITW
Automotive Refinishing.
DV-AGMD-101599.9
Service Manual Price: $30.00 (U.S.)
DeV
ilbiss W
orldwide Sales and Service Listing - www
.devilbiss.com
DeVilbiss
Worldwide
www.devilbiss.com
Technical/Service Assistance
ITW Automotive Finishing
ITW Automotive Refinishing
ITW Industrial Finishing
ITW Ransburg
Telephone: 800/ 626-3565
Telephone: 800/445-3988
Telephone: 800/ 992-4657
Telephone: 800/ 233-3366
Fax: 419/ 470-2040
Fax: 800/445-6643
Fax: 800/ 246-5732
Fax: 419/ 470-2071
Technical Support Representative will direct you to the appropriate telephone
number for ordering Spare Parts.
© 2006 Illinois Tool Works Inc. All rights reserved.
Models and specifications subject to change without notice.
Form No. DV-AGMD-101599.9
Litho in U.S.A.
05/06

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project