PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-1 - LINEAR P/N: 235686 X21 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2
GD00Z-1
GARAGE DOOR OPENER
REMOTE COMMAND
CONTROLLER with TILT SENSOR
Installation Instructions
PO W ER
I N PUT
JACK
STATUS
I N DICATOR
TILT
SENSOR
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340 www.linearcorp.com
CO N TROLLER
CO NN ECTIO N
W IRES
CONTROLLER
POWER
SUPPLY
RETAINING
BRACKET
DOUBLE SIDED
MOU N TI N G TAPE,
SCRE W S A N D A N CHORS
W AR N I N G
LIGHT
LI N K
BUTTO N
ADJUSTABLE
MOUNTING
BRACKET
(OPTIO N AL)
POWER
SUPPLY
The Model GD00Z-1 is a garage door opener Remote Command Controller with built-in Z-Wave® interoperable two-way RF mesh networking technology designed for use with Lowe’s Iris® hub. A garage door opener connected to the Controller can be remotely activated using the Iris web interface or Iris mobile applications.
The GD00Z-1 Controller connects to the garage door opener’s pushbutton wall console terminals and communicates with the Iris hub using Z-Wave radio signals. A wireless tilt sensor mounts on the garage door and reports the door’s position to the
Controller. When the Controller receives a command from the Iris hub, it will open or close the garage door.
Anytime the garage door opener is activated remotely by the Controller, a warning indicator fl ashes and a beeper sounds for fi ve seconds before the door begins to move.
If, due to an obstruction or other cause, the door does not completely open or close when it is activated remotely, the Controller will pause for 30 seconds. After the delay, a second remote activation can be attempted. If the door does not complete its motion on the second attempt, the Controller will suspend operation until the door is operated locally with the opener’s pushbutton wall console.
The Controller is powered by a plug-in power supply. The Model TILT 345 tilt sensor is powered by a 2032 lithium battery. If the tilt sensor battery is low, it will be reported to the Iris hub by the Controller. A link button and status light are provided on the
Controller for adding or removing the device with the Iris hub.
Four screws and anchors are provided for mounting the Controller. An adjustable controller mounting bracket with hardware is supplied for installing the unit onto the door opener’s hanging hardware. The wireless tilt sensor mounts with double sided tape or the two screws supplied.
WARNING
This operator system is equipped with an unattended operation feature. This door could move unexpectedly.
NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll up) doors only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
The Remote Command Controller must be mounted in the garage, in sight of the garage door, where the visual and audible movement warning indicators can be clearly seen and heard.
WARNING
Do not install the Remote Command Controller on garage door operators manufactured prior to 1993
(models without an operational safety beam entrapment detection system).
Z-Wave® is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.
4. TILT SENSOR INSTALLATION AND BATTERY
TO ACTIVATE THE TILT SENSOR, REMOVE THE BATTERY PROTECTION PULL STRIP
ARROWS ON PLATE
& SENSOR POINT UP
ATTACH MOU N TI N G PLATE
TO TOP PANEL OF THE DOOR
S N AP SE N SOR O N TO
THE MOU N TI N G PLATE
5. PAIRING WITH IRIS
W ALL
OUTLET www.lowes.com/iris
PO W ER
SUPPLY
PO W ER
I N PUT
JACK
CO N TROLLER
LI N K
BUTTO N
"UP"
ARRO W S
POST O N
BOTTOM
IRIS WILL NOTIFY YOU WHEN
THE BATTERY IS LOW,
REPLACE THE BATTERY WITH
A TYPE CR2032 COIN CELL
USE DOUBLE SIDED TAPE OR
THE T W O MOU N TI N G SCRE W S SUPPLIED
(DRILL 1/16" PILOT HOLES IF REQUIRED)
TO OPE N THE CASE, T W IST
A SMALL SCRE W DRIVER
I N CASE SLOT
SLOT
PLUS SIDE UP !!!
I N SERT THE
BATTERY
I N TO THE
TRA N SMITTER
CR2032
1
TO PAIR WITH
THE IRIS HUB
PARING THE CONTROLLER
FROM THE IRIS W EB SITE, CLICK
"DEVICES", THE N CLICK THE
"ADD DEVICES" BUTTO N
2 SELECT GARAGE DOOR
CO N TROLLER FROM THE LIST
3 FOLLO W THE O N -SCREE N
I N STRUCTIO N S TO PAIR THE
CO N TROLLER W ITH THE HUB
4 W HE N I N STRUCTED, PRESS
THE LI N K BUTTO N O N THE
CO N TROLLER
1
TO REMOVE FROM
THE IRIS HUB
REMOVING THE CONTROLLER
FROM THE IRIS W EB SITE,
CLICK "DEVICES"
2 O N THE GARAGE DOOR
CO N TROLLER DEVICE CLICK
"MA N AGE", THE N CLICK "REMOVE"
3 FOLLO W THE O N -SCREE N
I N STRUCTIO N S TO U N -PAIR THE
CO N TROLLER W ITH THE HUB
4 W HE N I N STRUCTED, PRESS
THE LI N K BUTTO N O N THE
CO N TROLLER
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-1 - LINEAR P/N: 235686 X21 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 2 OF 2
TILT SE N SOR
MOU N TED O N
THE TOP PA N EL
OF THE DOOR
THE CONTROLLER TYPICALLY
MOUNTS ON THE CEILING
NEAR THE OPENER AND
THE POWER OUTLET
2 PLUG THE PO W ER CORD
I N TO THE PO W ER I N PUT
JACK O N THE CO N TROLLER
1 USE THE IRIS W EB SITE A N D MOBILE
APPS TO CO N TROL YOUR GARAGE
DOOR, VIE W STATUS, A N D SET
CUSTOM RULES
2 THE CO N TROLLER W ILL BEEP A N D
FLASH FOR FIVE SECO N DS BEFORE
THE DOOR MOVES
3 THE CO N TROLLER W ILL ACTIVATE
THE DOOR OPE N ER A N D OPE N
OR CLOSE THE DOOR
BEEP
BEEP
BEEP
3/16" HOLES
FOR A N CHORS
THE CONTROLER'S WARNING
LAMP MUST BE VISIBLE IN
ALL DOOR POSITIONS
THE CONTROLLER CAN ALSO BE ATTACHED TO THE OPENER'S
HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET
THE OPTIO N AL ADJUSTABLE
MOU N TI N G BRACKET FITS
3 W AYS O N THE CO N TROLLER
SECURE
BRACKET
W ITH SCRE W
I N DE N T
THE BRACKET S N APS O N TO
I N DE N TS O N EITHER SIDE OR
O N THE E N D OF THE CO N TROLLER
I N DE N T
1
CO NN ECT THE CO N TROLLER CO NN ECTIO N
W IRES TO THE PUSHBUTTO N W ALL
CO N SOLE TERMI N ALS O N THE GARAGE
DOOR OPE N ER. THE TERMI N ALS MAY BE
N AMED "P W C", " W C", "PB", "PUSHBUTTO N ",
OR "RED A N D W HITE". TERMI N AL N AMES
A N D LOCATIO N S VARY BY MODEL.
3 PLUG THE PO W ER SUPPLY
I N TO 115 VAC OUTLET
A N D SECURE IT W ITH
THE RETAI N I N G BRACKET
DO NOT DISCONNECT
ANY WIRES CURRENTLY
CONNECTED TO THE
GARAGE DOOR OPENER !!!
EITHER W IRE
CA N CO NN ECT
TO EITHER
TERMI N AL
BE SURE WIRES ARE
CLEAR OF ALL MOVING
PARTS OF THE GARAGE
DOOR AND OPENER
I N DE N T
GARAGE
DOOR
OPENER
USE THE BOLTS A N D N UTS
SUPPLIED TO ATTACH THE
BRACKET TO A SECURE
STRUCTURE
USE THE FOUR SCRE W S
A N D A N CHORS TO MOU N T
THE CO N TROLLER ABOVE
THE OPE N ER
BE SURE THE CONTROLLER
IS CLEAR OF ALL MOVING
PARTS OF THE GARAGE DOOR
10. TROUBLESHOOTING
1. The warning light will fl ash and the warning beeper will sound fi ve seconds before the door opener is activated.
MOVE!
STAY CLEAR
OF THE DOOR, AND DOOR OPENER. THEY ARE ABOUT TO
2. If the door does not completely open or close after remote activation, the Controller will allow user to try to operate the door one more time. If the second attempt fails, the Controller will go into lock-out mode and blink the status indicator. See Note #3.
3. If the status indicator is blinking, the Controller is in lock-out mode and will not accept remote commands. Activate the door from the pushbutton wall console then check that the status indicator stops blinking.
NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION:
THIS PRODUCT CONTAINS A CR COIN CELL LITHIUM BATTERY WHICH CONTAINS
PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY - SEE www.dtsc.ca.gov/hazardouswaste/perchlorate
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY IS SWALLOWED, PROMPTLY SEE A DOCTOR.
DO NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA.
Changes or modifi cations not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
Les changements ou modifi cations non approuvés expressément par la partie responsable de la conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.
PROBLEM
The Controller does not fl ash or beep when activated.
The Controller fl ashes and beeps when activated but the door does not move.
POSSIBLE
CAUSE
No power to the Controller.
Obstruction blocking the door or incorrect wiring.
Garage door opens or closes, but the status does not change on the Iris website or mobile app.
The tilt sensor signal is not being received by the
Controller.
CORRECTIVE ACTION
1. Make sure the power supply is plugged in securely to a live outlet.
2. Make sure the power cord is plugged in securely to the Controller.
1. Make sure that there are no obstacles preventing the door from moving.
2. Make sure that the Controller’s connection wires are connected to the proper terminals on the garage door opener. Trace the wires from the garage door opener’s pushbutton wall console to the door opener. This is where the Controller’s connection wires should be connected to.
1. Make sure the tilt sensor is mounted correctly on the garage door, with the arrow pointing up.
2. Make sure the battery pull tab has been removed from the tilt sensor.
3. Replace the battery in the tilt sensor.
4 THE IRIS W EB PAGE OR MOBILE
APP W ILL SHO W THE N E W STATUS
OF THE DOOR AFTER THE DOOR
COMPLETES ITS CYCLE
FLASH
FLASH
FLASH
STAY CLEAR
OF THE DOOR !!!
LINEAR LIMITED RETAIL WARRANTY
Linear LLC (the Company) warrants to the original purchaser that products delivered hereunder will be free of defects in materials and workmanship for a period of one (1) year from the date of purchase.
The Company within said period shall at its option, either repair or replace free of charge, any product or part thereof found, upon the Company’s inspection, to be so defective, and will return the repaired or replaced product to the purchaser at Company’s expense.
All products returned for warranty service require a Return Product Authorization Number (RPA#).
For warranty service, shipping instructions, and an RPA#, contact Linear Technical Services at
1-855-546-3351. Devices must be sent to the Company at owner’s expense and be accompanied with statement of defect and proof of purchase.
This warranty is conditioned on the following:
1. The Company must be notifi ed within one year of purchase and have been given the opportunity of inspection by return of any alleged defective product free and clear of all liens and encumbrances to the Company or its distributor; and
2. The product must not have been abused, misused or improperly maintained and/or repaired during such period; and
3. Such defect has not been caused by corrosion or exposure to other than ordinary wear and tear.
THE COMPANY MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND
WHATSOE V ER INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
The Company’s maximum liability hereunder is limited to the purchased price of the product. In no event shall the Company be liable for any consequential, indirect, incidental or special damages of any nature arising from the sale or use of the product, whether based in contract, tort, strict liability or otherwise.
Note: Some states do not allow limitations on incidental or consequential damages or how long an implied warranty lasts, so that the above limitations may not fully apply. This warranty gives specifi c legal rights and you may also have other rights which may vary from state to state.
This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Copyright © 2014 Linear LLC 235686 X21