AT&T SW-ATT-DC Wireless Device Controller Installation Instructions

Below you will find brief information for Wireless Device Controller SW-ATT-DC. This wireless device controller can be used to control AC power to small appliances such as lamps. Simply plug the device directly into an AC power outlet and then install the retaining screw into the plastic tab located at the top of the unit to secure the unit to the AC outlet. Then plug the lamp or other small appliance into the unit.

PDF Download

Document

SW-ATT-DC RTL 41807

Product Description

The AT&T model number SW-ATT-DC is a 915MHz Wireless

Device Controller that is used to control AC power to small appliances, such as a lamp. The unit is plugged directly into one socket of an AC power outlet. Then install the retaining screw into the plastic tab located at the top of the unit to secure the unit to the AC outlet.

This Device Controller can be utilized to control turning lamps and other small appliances on and off.

Follow these steps to install the Device Controller:

1. Plug the Device Controller into an AC power outlet.

2. Plug the lamp or other small appliance into the unit.

Discovering and Registering the Device Controller

Follow these steps to discover and register the device controller: Step Action

1. Place the DLC into Discovery Mode in DLD.

2. Make the Device Controller discoverable by pressing the

Learn button located on the side of the unit.

3. Confi rm that the Device Controller has been discovered in DLD.

4. Label the Device Controller in DLD.

This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. exploitation est autorisée aux deux conditions suivantes: (1) appareil ne doit pas produire de brouillage, et (2) utilisateur de appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible en compromettre le fonctionnement.

LISTED

Installation Instructions

FCC Compliance Statement

This device complies with FCC Rules and

Regulations as Part 15 devices as well as

Industry Canada license exempt RSS Rules and Regulations. Operation is subject to the following two (2) conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation.

Hello! I am an AI chatbot specifically trained to assist you with the AT&T SW-ATT-DC Wireless Device Controller Installation Instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

915MHz Wireless Device Controller
Control AC power to small appliances
Plug directly into AC power outlet
Control turning lamps and other small appliances on and off

Frequently asked questions

Plug the Device Controller into an AC power outlet. Plug the lamp or other small appliance into the unit.

Place the DLC into Discovery Mode in DLD. Make the Device Controller discoverable by pressing the Learn button located on the side of the unit. Confirm that the Device Controller has been discovered in DLD. Label the Device Controller in DLD.

This device complies with FCC Rules and Regulations as Part 15 devices as well as Industry Canada license exempt RSS Rules and Regulations.