Performance Gear Series Wireless
English
Shure Performance Gear Wireless
Designed especially for performers who manage their own sound, Shure Performance Gear professional audio products deliver legendary Shure sound quality, stage-proven durability and hasslefree setup for worry-free performance.
Performance Gear Wireless systems are available in a variety of configurations - for handheld, guitar, headset and presentation applications. Manual frequency selection and transmitter setup provide specific choice and precise control to locate the clearest channel, every time.
System Components
All systems include
Internal Antenna Diversity PG4 receiver
One 9 volt battery
Power supply
User guide
Vocalist systems include
Microphone Head
PG2 handheld transmitter
Microphone clip
Lavalier, Headworn, and Instrument systems include
PG1 body pack transmitter
Microphone (choice of PG185, PG30)
Guitar systems include
PG1 bodypack transmitter
4-pin mini connector (TA4F) to 1/4” connector cable
Patent numbers 6,597,301 and 6,296,565
2
English
PG4 Receiver Features
Figure 1. Front Panel
audio LED
Indicates strength of incoming audio signal: green for normal, amber for strong, red for peak.
ready LED
Green LED indicates system is ready for use.
Channel Display
See “System Setup” on page 6.
channel button
Press and hold to change the frequency channel.
Figure 2. Back Panel
AC adapter jack
Adapter cord relief
XLR balanced microphone output jack
1/4” unbalanced output jack
3
English
PG2 Handheld Transmitter
Power/Mute Button
Power/Mute LED (See LED status below)
Channel Display (Display turns off after 10 seconds to conserve battery)
Channel Button
Battery Cover — Twist counter-clockwise to remove.
Battery Compartment
LED Status
Green
Amber
Red
Signifies
Ready
Mute is on
Battery is low
Battery dead (must be replaced for transmitter to operate).
Flashing Red on startup
Flashing Green and Red
Flashing Amber and Red
Controls are locked
Mute is on and battery is low
Figure 3.
Changing Battery
• Expected life for a 9 volt alkaline battery is approximately 8 hours.
• When the Power/Mute LED glows red, the battery should be replaced immediately.
Adjusting Gain
• Access the Gain Adjustment Switch by unscrewing the microphone head.
Use the tip of a pen or a small screwdriver to move the switch. (See fig. 4)
• The switch can be positioned in two gain settings on the PG2:
Gain Setting Suggested Uses
0dB
–10dB
For quiet to normal vocal performance.
Use only if audio is distorted due to high vocal levels.
Figure 4.
4
PG1 Bodypack Transmitter
Figure 5.
Figure 6.
Battery Cover, pinch sides to fold open
Wearing the Bodypack Transmitter
• Clip the transmitter to belt or guitar strap as shown. If using a belt, slide the transmitter until the belt is pressed against the base of the clip.
4-Pin Microphone Input Jack
Power/Mute Button. Press and hold to turn on/off.
Press and release to mute/unmute.
Power/Mute LED (see LED Status below)
Antenna
Channel Display
Channel Button
Gain Switch
9V Battery compartment
Battery Cover. Pinch sides to fold open.
LED Status
Green
Signifies...
Ready
Amber
Red
Flashing red on startup
Flashing Green and Red
Flashing Amber and Red
Mute is on
Battery is low
Battery dead (must be replaced for transmitter to operate).
Flashing Green and Red
Mute is on and battery is low
Changing Battery
• Expected life for a 9 volt alkaline battery is approximately 8 hours.
• When the Power/Mute LED glows red, the battery should be replaced immediately.
Figure 7.
Adjusting Gain
• Three gain settings are available on the PG1:
Gain Settings mic
0
-10
Suggested Use
Microphone
Guitar
Use only if audio is distorted due to high input level
English
5
6
English
System Setup
Single Receiver Setup
In any wireless setup, each transmitter and receiver pair must be tuned to the same frequency, or channel. Follow these steps to set the transmitter and receiver to the same channel:
1. Plug in the receiver to turn power on. Turn transmitter power off .
2. Press and hold the channel button on the receiver for about one second to enter select mode. Release the button as soon as the display begins flashing.
3. Press the channel button while the number is flashing to change to the next channel *.
4. To activate a newly selected channel, simply wait until the number stops flashing.
5. Turn on the corresponding transmitter.
6. Press and hold the channel button on the transmitter to enter select mode. Release the button as soon as the display begins flashing.
7. Press the channel button while the number is flashing to change to the next channel.
Scroll through the channels until the transmitter setting matches the channel on the receiver.
8. The transmitter channel is set when the number stops flashing. The green “ready” LED on the receiver will indicate the system is ready for use.
Figure 8.
*Note: Some of the frequencies available on the PG4 receiver may be occupied by sources of interference such as broadcast television or other wireless devices. Use the Busy Indicator on the receiver channel display to avoid selecting an occupied channel while in select mode.
Busy Indicator
When selecting channels, if the display flashes between a number and a blank screen, the channel is clear. If the display flashes between a number and a dash as shown in Figure 9, the channel is busy. This means that the channel is occupied by another device or source of interference. In this case, it is recommended to select another channel.
Figure 9.
M10
3
4
5
CH
1
2
8
9
6
7
0
English
Multiple System Setup
To set up multiple systems, repeat the previous steps for each transmitter and receiver pair. Once transmitters have been set, leave them on. Be sure to set each transmitter and receiver pair to a different frequency. For information about frequencies and compatibility, refer to the guide below.
TLPW Frequency and Channel Guide
In each group, channels 1,3,5,7 and 9 are a compatible set and channels 2,4,6,8 and 0 are a compatible set. When operating multiple systems, select only odd or even numbered channels for best results.
674-686
Freq
674.775
676.700
677.900
682.025
685.500
674.025
680.975
682.775
684.000
685.900
R10
3
4
5
CH
1
2
8
9
6
7
0
800-812
Freq
802.100
803.675
805.750
809.100
810.550
802.325
803.550
805.100
808.600
810.025
P11
3
4
5
CH
1
2
6
7
8
702-714
Freq
702.150
703.600
705.500
707.100
708.400
710.100
712.650
713.850
Q11
5
6
3
4
CH
1
2
740-752
Freq
740.150
741.600
743.500
746.400
748.100
751.850
R11
5
6
3
4
7
8
CH
1
2
7
8
5
6
9
0
3
4
1
2
H7
CH
539.175
545.175
540.375
546.375
541.975
547.975
536 - 548
Freq
536.050
542.050
537.400
543.400
770-782
Freq
770.150
771.600
773.500
775.100
776.400
778.100
780.650
781.850
7
8
5
6
9
0
3
4
1
2
K7
CH
593.175
599.175
594.375
600.375
595.975
601.975
590 - 602
Freq
590.050
596.050
591.400
597.400
R12
5
6
3
4
CH
1
2
7
8
5
6
9
0
3
4
1
2
M7
CH
794-806
Freq
794.150
797.500
799.100
800.400
802.100
805.850
JB
5
6
3
4
CH
1
2
7
8
5
6
9
0
3
4
1
2
T10
CH
665.175
671.175
666.375
672.375
667.975
673.975
662-674
Freq
662.050
668.050
663.400
669.400
863.900
855.275
857.925
861.550
863.200
864.500
854 - 865
Freq
854.900
856.575
857.950
861.750
806-810
Freq
806.125
806.375
807.125
807.750
809.000
809.500
7
8
Troubleshooting
Issue
No sound or faint sound
LED Status Solution
Transmitter Power/Mute
LED on, receiver LEDs on
• Perform transmitter setup (see page 6).
• Verify all sound system connections.
• Adjust transmitter gain.
Receiver Channel Display • Make sure AC adapter is securely plugged into electrical outlet and into
POWER connector on rear panel of receiver .
• Make sure AC electrical outlet works and is supplying proper voltage.
Transmitter LED glowing or flashing red
Transmitter LED off
• Replace transmitter battery.
Distortion or unwanted noise bursts
• Turn transmitter on.
• Make sure the +/– indicators on battery match transmitter terminals.
• Insert fresh battery.
• Remove nearby sources of RF interference (CD players, computers, cell phones, digital effects, in-ear monitor systems, etc.)
• Change receiver and transmitter to a different frequency.
• Reduce transmitter gain.
• Replace transmitter battery.
• If using multiple systems, change the frequency of one of the active systems.
• Adjust transmitter gain as necessary. Sound level different from cabled guitar or microphone, or when using different guitars
Cannot turn transmitter on
Transmitter LED flashing red
• Replace transmitter battery.
Locking and Unlocking Controls
Locking the system controls prevents accidental muting or channel adjustment during performance.
Transmitter
To lock the controls: turn the transmitter off, hold the channel button down and turn the transmitter power on. The Power/Mute LED will alternate between red and green.
To unlock the controls: with the transmitter on, hold the channel button down, and turn the transmitter off.
English
Specifications
System
PG1 Bodypack
Transmitter
PG2 Handheld
Transmitter
����
PG4 Receiver
Working Range 75m (250 ft.) Note: actual range depends on RF signal absorption, reflection, and interference.
Audio Frequency Response Minimum: 45 Hz.
Maximum: 15 kHz (overall system frequency depends on microphone element).
Total Harmonic Distortion 0.5%, typical
Ref. +/– 33 kHz deviation, 1 kHz tone
>100 dB A-weighted Dynamic Range
Operating Temperature
Range
Transmitter Audio Polarity
–18°C (0°F) to +57°C (+135°F) Note: battery characteristics may limit this range
Positive pressure on microphone diaphragm (or positive voltage to tip of
WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output.
Audio Input Level –10 dBV maximum at “mic” gain position
+10 dBV maximum at 0dB gain position
+20 dBV maximum at –10dB gain position
Gain Adjustment Range
Input Impedance
RF Transmitter Output
Dimensions
Weight
Housing
Power Requirements
Battery Life
Audio Input Level
Gain Adjustment Range
RF Transmitter Output
Weight
Housing
Power Requirements
Battery Life
Dimensions
Weight
Output Impedance
Housing
Audio Output Level Ref.
+/– 33 kHz deviation with 1 kHz tone
Sensitivity
Image Rejection
Power Requirements
30 dB
1MΩ
10 mW typical
110 mm H x 64 mm W x 21 mm D (4.3 x 2.5 x 0.8 in.)
75 grams (2.6 oz.) without battery
Molded poly carbonate case
One 9V alkaline battery
>8 hours (alkaline)
+2 dBV maximum at –10dB position
–8 dBV maximum at 0dB position
10dB
10 mW typical
218 grams (7.7 oz.) without battery
Molded PC/ABS handle and battery cup
One 9V size alkaline or rechargeable battery
>8 hours (alkaline)
188 mm L x 103 mm W x 40 mm D (7.4 in. x 4.0 in. x 1.5 in.)
241 grams (8.5 oz)
XLR connector: 200 Ω 1/4 inch connector: 1kΩ
ABS
XLR connector (into 600 Ω load): –19 dBV
1/4 inch connector (into 3000 Ω load): –5 dBV
–105 dBm for 12 dB SINAD, typical
>50 dB, typical
12–18 Vdc at 150 mA, supplied by external power supply
9
English
Replacement Parts
All Systems
System-Specific
Optional
Microphone Stand Adapter (PGX2)
AC Adapter (120 VAC, 60 Hz)
AC Adapter (230 VAC, 50/60 Hz, Europlug)
AC Adapter (230 VAC, 50/60 Hz, UK)
AC Adapter (100 VAC, 50/60 Hz)
AC Adapter (220 VAC, 50 Hz, China)
PG58 Head with Grille
Belt Clip
Universal Rack Tray
4-pin mini connector (TA4F) to 1/4” connector cable
WA371
PS20
PS20E
PS20UK
PS20J
PS20CHN
RPW108
44A8035
URT
WA302
10
English
Regulatory Information
Regulatory Information for North America, Europe, and Australia
PG1 & PG2 Transmitters: Certified to FCC Part 74 (FCC ID: “DD4PG1” and “DD4PG2”). Certified by IC in Canada under RSS-123 and RSS-102 (“IC: 616A-PG1” and “IC: 616A-PG2”). Meets the essential requirements of the European R&TTE Directive 99/5/EC (ETSI EN 300-422 Parts 1 & 2,
EN 301 489 Parts 1 & 9) and are eligible to carry the CE marking.
0978
PG4 Receiver: Authorized under Declaration of Conformity (DoC) provision of FCC Part 15. Certified under Industry Canada to RSS-123 (“IC: 616A-PG4”). This class B digital apparatus complies with Canadian ICES-003. Meets the essential requirements of the European R&TTE Directive
99/5/ EC (EN 301 489 Parts 1 & 9, EN 300 422 Parts 1 & 2) and is eligible to carry the CE marking.
Conforms to Australian EMC requirements and is eligible for C-Tick marking.
N108
Z540
0978
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
PS 20 Series Power Supplies: Conform to Safety Standard IEC 60065. PS20E and PS20UK are eligible to bear CE marking.
A ministerial license may be required to operate this equipment in certain areas.
Consult your national authority for possible requirements.
This radio equipment is intended for use in musical professional entertainment and similar applications.
Caution: changes or modifications not expressly approved by Shure Incorporated for compliance could void the user’s authority to operate the equipment.
Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
11
12
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 847-600-2000 U.S. Fax: 847-600-1212
Int’l Fax: 847-600-6446
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414
Asia, Pacifi c:
Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055
