Siemens STG Hand-Held Terminal PRO, MOBY D, MOBY E, MOBY I User's Guide
Below you will find brief information for STG Hand-Held Terminal PRO, MOBY D, MOBY E, MOBY I. This guide describes the STG Hand-Held Terminal PRO, a powerful tool for MOBY D, MOBY E, and MOBY I identification systems. You will learn about the program's features, how to use it, and how to configure the terminal for different applications.
Advertisement
Advertisement
MOBY
STG Hand-Held Terminal PRO
User’s Guide
Table of Contents
General
Commissioning the
STG Hand-Held Terminal PRO
Using the
STG Hand-Held Terminal PRO
The “MOBY D/E/I”
Programs
The “FILEHANDLER”
Program
Expanded Functions
Error Messages
Technical Data
Appendix
(5)J31069-D0126-U001-A6-7418
Published in May 2007
Safety Guidelines
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.
!
Danger indicates that death or severe personal injury will result if proper precautions are not taken.
!
Warning indicates that death or severe personal injury may result if proper precautions are not taken.
!
Caution with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
Caution without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
Notice indicates that an unintended result or situation can occur if the corresponding information is not taken into account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and operation of a device/system may only be performed by qualified personnel . Within the context of the safety notes in this documentation qualified persons are defined as persons who are authorized to commission, ground and label devices, systems and circuits in accordance with established safety practices and standards.
Prescribed Usage
Note the following:
!
Warning
This device may only be used for the applications described in the catalog or the technical description and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage, positioning and assembly as well as careful operation and maintenance.
Trademarks
All names identified by are registered trademarks of the Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency.
However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Automation and Drives
Postfach 48 48
90437 Nürnberg
GERMANY
(5)J31069-D0126-U001-A6-7418
Edition 05/07
Copyright E Siemens AG 1999, 2000, 2002, 2003, 2007
Technical data subject to change
R 05/07 Table of Contents
Table of Contents
1 General
1.1
1.2
1.3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCC Information for the USA . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Commissioning the STG Hand-Held Terminal PRO . . . . . . . . . . . . .
2.1
2.2
2.3
2.4
Included Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turning on the Device and Setting the Operating Mode . . . . .
MOBY Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Using the STG Hand-Held Terminal PRO . . . . . . . . . . . . . . . . . . . . . .
3.1
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.1
Modifier keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.2
Key functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
3.3
Antenna on the Read Head and Antenna Field
Charging Function
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-12
4 The “MOBY D/E/I” Programs
4.1
Data Editor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2
4.2.1
General Information on Read and Write-Accessing an MDS E-19
4.2.2
4.2.3
MDS Functions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reading the MDS
Writing the MDS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.4
Erasing/Initializing the MDS
4.2.5
Reading the ID Number
4.2.6
Reading Raw Data
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3
File Functions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.1
Loading a File
4.3.2
Saving
4.3.3
Exiting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4
The Editor Functions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.1
Jump to Address
4.4.2
Display
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.3
Clear Display
4.4.4
Edit Date
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-I
Table of Contents R 05/07
4.5
The Extras Functions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.1
Communication
4.5.2
Password
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.3
Antenna
4.5.4
Address Setup
4.5.5
4.5.6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MOBY I Setup
MOBY E Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6
The “?” Functions
4.6.1
Language
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6.2
About
4.6.3
Version
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 The “FILEHANDLER” Program
5.1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Information on the Filehandler
. . . . . . . . . . . . . . . . . . . E-30
5.2
The Filehandler Commands
. . . . . . . . . . . . . . . . . . . . . . . . . . . . E-31
5.3
View of the Editor and Directory
5.3.1
The Data Editor of the Filehandler
5.3.2
View of the Directory
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4
The File Menu
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4.1
Read File from MDS (Read File from Tag)
. . . . . . . . . . . . . . . .
5.4.2
Read File from STG RAM
5.4.3
5.4.4
5.4.5
Write File to MDS (Write File to Tag)
Write File to STG RAM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Read Directory from MDS (Read Dir from Tag)
5.4.6
Read Directory from STG RAM (Read Dir from STG RAM)
5.4.7
Example: Copy Files
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-39
5.5
The Commands Menu
5.5.1
New File (Create File)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5.2
Delete File
5.5.3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Format MDS (Tag Format)
5.5.4
Attribute File (File Attribute)
5.5.5
MDS Status (Tag Status)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5.6
MDS Cover
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6
The Editor Menu
5.6.1
Display Directory
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6.2
Display Editor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6.3
Change File Size (File Size)
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6.4
Delete Display (Clear Display)
5.6.5
Jump to Address
5.6.6
Display Setup
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E-II
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Table of Contents
5.7
The Extras Menu
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.7.1
Parameter
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.7.2
Password for Filehandler (Password for FH)
5.7.3
Communication
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8
The “?” Functions
6 Expanded Functions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1
6.2
Copying MOBY Data from and to the
STG Hand-Held Terminal PRO
. . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.1
What Is Needed in Addition?
6.2.2
Installing procedure
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.3
Data exchange
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.4
Organization of the READ.HEX File
. . . . . . . . . . . . . . . . . . . . . .
6.2.5
Organization of the READ.HX1 File
. . . . . . . . . . . . . . . . . . . . . .
6.3
6.4
Storing the MDS Data on the STG Hand-Held
Terminal PRO
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-48
Functions with the PSION Operating System
. . . . . . . . . . . . . . E-54
Automatic Power Saver Function
. . . . . . . . . . . . . . . . . . . . . . . . E-55
6.5
Connecting SIM Devices (MOBY E/I)
6.5.1
Security
. . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6
System RESET
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-59
7 Error Messages
7.1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Messages with the “MOBY D/E/I” Programs
7.2
Error Messages with the “FILEHANDLER” Program
8 Technical Data
A Appendix
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.1
A.2
Ordering Components for Expanded Functions
Porting User Applications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-70
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-III
Table of Contents R 05/07
E-IV
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 General
1 General
The STG hand-held terminal PRO (service and test device) is a powerful addition to the MOBY D, MOBY E or MOBY I identification systems. It is a mobile hand-held terminal based on the PSION Workabout PRO and is designed for applications in the areas of logistics, distribution and service. In addition, it is an indispensable aid when commissioning and testing.
STG hand-held terminal PRO with
MOBY D/E/I reader head
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-1
General R 05/07
1.1
Application Areas
The STG hand-held terminal PRO can be used with MOBY D, MOBY E and
MOBY I. The included service and test program makes it easy to read and write all data memories of MOBY D, MOBY E or MOBY I.
In addition, it is very simple for customers to program their own applications on the hand-held terminal. A C library is available from Siemens for programming the hand-held terminal read heads. Implementation of applications in the areas of warehousing, logistics and commissioning is easy.
Very sturdy in design and protected against splashed water, the hand-held terminal can also be used in rugged environments. Its display is easy to read by the available display illumination.
1.2
Product Description
The STG hand-held terminal PRO consists of a basic device and a read head from
MOBY D, MOBY E or MOBY I. The basic device is a PSION Workabout PRO.
This device is the worldwide standard for industrial hand-held terminals. The service and test program starts automatically when the hand-held terminal is turned on. All data memories of MOBY D, MOBY E or MOBY I can be processed with the hand-held terminal.
E-2
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 General
The following functions can be executed.
S Read data from the MDS
S Write data to the MDS
S Delete the entire data memory (write with a filler value)
S Read and display the ID number of the MDS (MOBY D/E)
S Represent and edit the data in hexadecimal and ASCII format
S Enable/disable password protection for all write-access functions and for exiting the MOBY program
S Menu prompting in various languages (German and English)
S Store read MOBY data in files. Approximately 40 MB are available for this on the hand-held terminal.
Additional functions with the MOBY I filehandler
S Format the MDS
S Create files on the MDS
S Write files to the MDS
S Read files from the MDS
S Read and display the directory
S Delete files from the MDS
The read/write head of MOBY D/E/I is screwed to the PSION basic device. The head is equipped with a serial TTL interface for communication with the basic device. The read head is powered by the basic device.
The read/write head can also be ordered separately so that customers can continue to use an already existing PSION Workabout PRO.
The appropriate charging device (including 110...240 V plug-in power pack) for recharging the batteries must be ordered separately.
S MOBY D/E/I
The charging device (order number see catalog) is designed as docking station.
For customer-specific RFID applications, a C library is available to the user with the functions of the MOBY read head. Users can develop their own programs
(cf. appendix A.2) with the optional C development environment.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-3
General
R 05/07
1.3
FCC Information for the USA
S PSION basic device – See PSION user’s manual.
S MOBY E/I read head
Made in Germany
SIEMENS MOBY STG
FCC ID
NXW-MOBYESTG
THIS DEVICE COMPLIES WITH PART 15 OF THE
FCC RULES: OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
Note
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
.
E-4
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Commissioning the STG Hand-Held Terminal PRO
2 Commissioning the STG Hand-Held Terminal PRO
2.1
Included Components
The STG hand-held terminal PRO consists of several components which are listed individually on the delivery slip.
Ordered
Components
MOBY D
STG hand-held terminal PRO
MOBY E
STG hand-held terminal PRO
MOBY I
STG hand-held terminal PRO
Order Number Pack List
6GT2603-0AA10 PSION Workabout PRO 1
MOBY D read head
6GT2303-0AA10 PSION Workabout PRO 1
MOBY E read head
6GT2003-1CA00 PSION Workabout PRO 1
MOBY I read head
Pack Number
6GT2603-1AA00
6GT2303-1AA00
6GT2003-1CA00
1 The MOBY application is pre-installed on the STG hand-held terminal PRO.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-5
Commissioning the STG Hand-Held Terminal PRO R 05/07
2.2
Turning on the Device and Setting the
Operating Mode
After the first charging of the battery the hand-held terminal is ready to operate straight away.
Switch the device on by pressing ENTER/ON for 4 seconds. A selection menu appears with the MOBY application for the RF read/write head which you want to.
MOBY D service and test program
MOBY E service and test program
MOBY I service and test program
MOBY I service and test program filehandler (The MDS data are accessed
The device goes off automatically after no keys have been pressed for 5 minutes. Turning on device by pressing red ENTER/ON key for appr. 4 seconds, the hand-held terminal continues with the same screen it was displaying before
it was turned off manually or automatically. See chapter 6.4.
Manually turn off is done by pressing blue FN key first and than red ENTER/ON key afterwards.
E-6
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Commissioning the STG Hand-Held Terminal PRO
2.3
MOBY Applications
If you use a different read head (MOBY D/E/I) with the hand-held terminal later on, you will have to change the MOBY application. Exit the running application with the FILE/EXIT menu. The PSION start screen appears. Select the required MOBY application.
2.4
User Interface
Use of the STG programs MOBY D/E/I on the hand-held terminal is described
Use of the Filehandler program for MOBY I is described in chapter 5.
All functions of the MOBY programs can be called with the yellow menu key.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-7
Using the STG Hand-Held Terminal PRO R 05/07
3 Using the STG Hand-Held Terminal PRO
3.1
Keyboard
The keyboard of the PSION Workabout PRO is divided into 3 parts.
S Control keys directly below the display
S Numerical key
S ASCII keyboard
Control keys: on/off, cursor keys;
CTRL key
The green LED flashes green when the battery is being charged and lights up continuously when charging has been completed.
Numeric input block
ASCII keyboard
Yellow Keys: Open MOBY application menu
E-8
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Using the STG Hand-Held Terminal PRO
3.1.1
Modifier keys
<SHIFT>
<CTRL>
<ALT>
<ORANGE>
<BLUE>
Activating the modifier keys:
When a modifier key is pressed/activated the designation of the selected modifier key appears in lower-case letters in the task bar, e.g. “org key”, “blue key”.
If another key is then activated, this alters its function and the display in the task bar disappears and the modifier key is deactivated again.
3.1.2
Key functions
<SHIFT>
Key
Arrow keys
(round gray key below display)
<BKSP>
<DEL>
(blue key and BKSP>
<CTRL>
<ALT>
<TAB>
Function
Display of upper-case letters (A-Z) and symbols that are also indicated on the numeric keys (e.g. &,
*,...).
Enable navigation in the display to the left, right, up and down.
Moves the cursor to the left to delete the last entered character.
Removes the character after the cursor.
<ESC>
<SPACE>
h f i f h k
Moves the cursor certain distances to the right or down.
(<ORANGE> and <TAB> moves the cursor back.)
Closes the currently open menu, dialog window or an application that has just been started and returns to the previous user interface.
Insertion of spaces.
In a Windows dialog window check boxes can be activated or deactivated with the <SPACE> key.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-9
Using the STG Hand-Held Terminal PRO R 05/07
3.2
Antenna on the Read Head and Antenna Field
The antenna of the read head is located on the top of the hand-held terminal.
The various types of MDSs offer different ranges. The following table gives you an overview.
MOBY D
MDS Type
D139
D160
MOBY E mm MDS Type
60 E600 (ISO card)
25 E611
MOBY I mm MDS Type
18 402/401
30 404/514/413E mm
6
20
D124
Labels based on
Basis I-Code:
30
E624 (button)
E623 (pill) 2
8 403
4/3 3 506
8
12
I-Code1
I-Code SLI
Tag-it HF-I my-d
75
100
100
100
439E
507
( i h b )
507
(without battery)
12
35
4
2 The pill can only be read on the head portion provided for this.
3 When MDS is installed in metal
4 Range tolerances are to be expected for manufacturing reasons. The distances apply to labels with the size 85 x 55 mm.
E-10
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07
Example:
MDS E600
MOBY D/E
Using the STG Hand-Held Terminal PRO
Surface antenna
MOBY E/I
Button antenna or rod antenna (MOBY I)
Example:
MDS E623
The antenna field for the STG read head
Antenna field for MOBY E
With the MOBY E read head, 2 antennas are integrated in the reader. These must be positioned on the read head based on which MDS you want to read.
The EXTRAS/ANTENNE command (see chapter 4.5.3) is used to switch the
antenna field. Remember that the MDS E623 can only be read on the antenna provided for this. See figure. The MDS E624 can be read on both the button antenna and the surface antenna.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-11
Using the STG Hand-Held Terminal PRO R 05/07
3.3
Charging Function
The battery charging procedure is started as soon as the PSION Workabout
PRO is placed in the docking station. Charging is activated and indicated with
When the batteries are empty, ca. 4 hours are required for a complete charge.
IMPORTANT: Be sure to adhere to the PSION user’s manual.
The backup battery
The backup battery in the PSION Workabout PRO is used to retain the application data when the main batteries are empty. The backup battery is a lithium cell. Remember that, when the main batteries are empty or have been removed, a loaded backup battery can only maintain the data in the RAM for just a few minutes.
The MOBY application is stored fail-safe in the flash memory and is therefore still present even if a battery fails. If the MOBY application has been deleted or damaged the device has to be sent in for repair.
E-12
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “MOBY D/E/I” Programs
4 The “MOBY D/E/I” Programs
After you turn on the STG hand-held terminal PRO, the editor appears on the display. You can view the data, enter new data or call a function with the yellow menu key. Functions can also be called directly. To do this, first activate the
ALT key and then the appropriate alphanumeric key. The table below lists all functions together with their direct calls.
Command
File/Load File
File/Save
File/Exit
Tag/Read
Tag/Write
Tag/Erase/initialize
Tag/Read TagId
Tag/Read raw data
Editor/Jump to address
Editor/Display
Editor/Clear
Editor/edit date
Extras/Communication I
Extras/Password for STG P
Extras/Address Setup G
Extras/MOBY I Setup
Extras/MOBY E Setup
T
M
W
E
S
X
R
C
A
J or Tab
D
L
Shortcut 1
H
Y
Description
Load file from PSION RAM drive to working storage
Store read MDS data on the RAM drive
Exit STG application
Read data from MDS
Write data to MDS
Write MDS with a certain value
Read ID number of MDS
Read physical memory of MDS
Jump to a certain address in editor
Change display options
Clear data in editor to a certain value
The date on which the cursor is positioned can be edited in a number of formats.
Change communication options
Change password for STG application
Define entries for the “read/write MDS” commands
Set memory size and MOBY I operating mode
Switch MDS access from “MOBY key” (A) to the B key
For MOBY E SIM: Switch between cyclic operation and continuous operation
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-13
The “MOBY D/E/I” Programs R 05/07
Command
?/Language
?/About...
?/Version
B
V
Shortcut 1
N
Description
Set menu language
Manufacturer’s data
Version of operating system and STG application
1 German shortcuts; use the English operating instructions for the English menu language.
E-14
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “MOBY D/E/I” Programs
4.1
Data Editor
The MDS data can be edited in hexadecimal or ASCII in the editor screen. This can be set in the EDITOR/DISPLAY menu.
The editor always shows the total size of an MDS memory. Use the cursor functions to access the individual addresses.
Use the “Tab” key to jump to any ad-
Indication of the currently set read head.
The TagId of the MDS is only displayed on the MOBY D/E. It is valid after the
“MDS/read-write-readTagId” function is executed.
Date field:
The date on which the cursor is located can also be shown in hexadecimal, decimal, ASCII or binary format. The
“Editor/edit date” function can be used to change the value in the date field.
The editor screen contains the MDS date. Standard setting is 32 bytes.
MDS addresses are shown in hexadecimal or decimal format.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-15
The “MOBY D/E/I” Programs
The “current area”
R 05/07
The editor uses normal representation for the “current area.” All other data areas of the MDS are shown inverted.
The current area shows the data block which was read last. During read/writeaccesses, the current area is entered as the value for the write command.
This value can be adjusted in the
TAG/WRITE or TAG/READ menu.
Current area
The current area is changed automatically when you edit data and overwrite.
E-16
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “MOBY D/E/I” Programs
The size of the memory area shown on the display can be switched
with the EDITOR/DISPLAY function. See chapter 4.4.2.
In the normal representation, 32 bytes are displayed in lower case letters. This gives you an overview of the MDS data.
In zoom representation, only 4 consecutive bytes are shown. Representation is in upper case letters. This display is easy to read.
Zoom representation (hexadezimal)
Zoom representation (ASCII)
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-17
The “MOBY D/E/I” Programs
4.2
MDS Functions
R 05/07
The MDS functions handle communication with the MDS.
The MDS function is not interrupted if you briefly move the MDS out of the read field. The MDS function is terminated if MDS processing does not take place for more than 30 seconds. See
After a command is started, a window with a bar appears on the display. This bar shows how much of the command has already been processed.
E-18
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “MOBY D/E/I” Programs
4.2.1
General Information on Read and Write-Accessing an MDS
The MOBY D and MOBY E MDSs use block-oriented data accessing. A read or write-access to an MDS is only possible at the beginning of a block. One block contains 16 bytes (or 10 hex) with MOBY E. Thus, the start addresses for MDS processing to be entered on the STG hand-held terminal PRO are:
00, 10, 20, 30 hex and so on.
With MOBY D a block has a length of 4 bytes (I-Code, Tag-it) or 8 bytes (my-d).
The start addresses are:
00, 04, 08, 12 hex ... (I-Code, Tag-it) or
00, 08, 10, 18 hex ... (my-d).
With the MOBY D/E, the TagId on the display is automatically updated to the current value after the read/write access.
However, you can also specify any start address. This will be accepted by the STG and corrected to the next lower block beginning. The corrected address is indicated for the operator in a window and must be acknowledged.
An additional window appears if you change data in the editor and then attempt to read an
MDS. The window tells you that the data which you have just modified may be overwritten again with the “read MDS” command.
You can retain or reject the modified data in the editor, or you can terminate the command completely.
Note
ECC mode can only be set on the MOBY I hand-held terminal.
ECC mode cannot be used with MOBY D/E.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-19
The “MOBY D/E/I” Programs R 05/07
4.2.2
Reading the MDS
A data block with a start and end address, which can be defined as desired, can be read from the MDS. If the same value is entered for the start and end address, only one block can be read from the MDS. The address area is indicated in another screen for confirmation.
Note
If mode “Complete MDS” was selected in the read/write field of the menu “Extras/Address Setup/...,” the “MDS/read” funktion is started immediately without asking any questions. The complete MDS is always processed.
4.2.3
Writing the MDS
A data block can be written to the MDS. The data block which is valid in the editor is indicated as the default for each write access. The default length or end address can still be changed to another value during the write-access.
4.2.4
Erasing/Initializing the MDS
The “erase/initialize MDS” function is used to write the entire MDS with a certain value in a very short time. The erasure value can be entered in a subsequent menu. After the deletion function has been performed, the memory in the editor is also erased with the value which was entered. With the MOBY I, the correct size of the MDS memory must be set (Extras/MOBY I Setup) before this function is performed.
4.2.5
Reading the ID Number
Only MOBY D/E: The function reads and indicates the serial number of the
MDS. The ID number is set at the factory and cannot be changed.
The TagId is displayed in hexadecimal format by the editor in the second line.
The TagId is automatically read with the “MDS read/write/erase” functions.
E-20
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “MOBY D/E/I” Programs
4.2.6
Reading Raw Data
Only MOBY D/E: This function is used to physically read the entire memory of the MDS. This includes TagId, key information (if public), manufacturer’s information and MDS access rights. A knowledge of the physical layout of the
MDS memory is required to interpret the data. See description of MFWAPI or
CCTWAPI.
The “read raw data” function can be used to detect errors made when the MDS was configured.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-21
The “MOBY D/E/I” Programs
4.3
File Functions
R 05/07
4.3.1
Loading a File
A file can be loaded to the STG editor which was
S saved before with the “file/save” command or
S transferred from the PC to the “folder /SIBO/M” drive of the PSION Work-
4.3.2
Saving
Data currently being displayed by the editor can be saved in a file on the
PSION Workabout PRO. The file name may consist of 1 to 8 letters or numbers. During the storage procedure, the extension “.HEX” (data) and
“.HX1” (ID no.) is automatically added to the file name. See also chapter 6.2.
A memory area of approximately 40 Mbytes is available on the hand-held terminal for storage of MDS data (i.e., with MOBY E, up to 40,000 MDSs can be read and stored).
4.3.3
Exiting
The “exit” function can be used to conclude the STG program of MOBY. This gives you access to the operating system levels of the PSION Workabout PRO.
E-22
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07
4.4
The Editor Functions
The “MOBY D/E/I” Programs
4.4.1
Jump to Address
You can enter a memory address in decimal or hexadecimal format. The setting can be changed under menu item Display/Display Address. This address will then be represented by the editor as the start address.
This function can also be triggered directly in the editor with the “Tab” key.
4.4.2
Display
The following settings are available in this menu.
S Switch the editor between 32-byte representation (i.e., 4x8= fine-print display) and 4-byte representation (i.e., 1x4= large, easy-to-read characters).
S No address is displayed for editor representation 1x5. The first 5 bytes of the read data are displayed. You cannot change to other addresses with the cursor.
S Switch the editor between hexadecimal and ASCII representation. The addresses are always shown in hexadecimal or decimal format.
S Switch date between “BIN,” “ASCII,” “DEC” and “HEX” format.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-23
The “MOBY D/E/I” Programs R 05/07
4.4.3
Clear Display
The “clear display” function is used to overwrite the entire memory in the STG editor with a value which you can specify. You can then change the desired data to the appropriate values in the editor. No function is performed on the
MDS.
S The data field can be shown in hexadecimal, ASCII, decimal or binary format. The data can also be changed with the “Indicate/edit date” function with the format set here.
S The addresses can be indicated in hexadecimal or decimal.
4.4.4
Edit Date
In addition to the standard formats hex and ASCII of the editor screen, the “edit date” function also provides the decimal and binary formats for data entry.
E-24
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07
4.5
The Extras Functions
The “MOBY D/E/I” Programs
4.5.1
Communication
S Interface
S Protocol
Switching between the TTL interface (read head) and the
RS 232 interface takes place here.
If the RS 232 setting is used, the protocol must be set to
“MOBY E/SIM” or “ASM 420/I/V.”
Certain protocols can be set here depending on which read head is being used.
Read Head Protocol That Can Be Set
MOBY D
MOBY E
MOBY I
MOBY D
MOBY D ISO
MOBY E
MOBY E/SIM
MOBY I
ASM 420/I/V
When the MOBY protocol is set, the memory size of the editor is also automatically specified for MOBY E.
With MOBY I, the memory size of the editor is set with the
“Extras/MOBY I Setup” function.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-25
The “MOBY D/E/I” Programs R 05/07
4.5.2
Password
A password can be programmed as an option. The password must be entered prior to a write-access function. Once entered, a password remains valid until the STG is turned off (i.e., the password only has to be entered once during several consecutive write commands). The “MOBY” program can also only be exited with the password.
Forgot the password?
If a password is forgotten, there is no way to obtain it again. The only solution is to reset the Software to delivery version. Activate in start menu supervisor
state (see chapter 6.5.1). Than do a shutdown/coldreset.
Password 99999999
Changing the password to 99999999 (i.e., eight 9s) has a special purpose.
The write-access function to the MDS and the “file/exit” function can no longer be executed. The password can also no longer be changed. The only way to access the write-access function again is to do a system reset (see
4.5.3
Antenna
Only for MOBY E: The antenna field on the read head is switched between
“card” (large antenna) and “button” (small antenna). See also chapter 3.2.
The antenna must be set once when the read head is commissioned. The set antenna is retained on the read head when the hand-held terminal is turned off.
E-26
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “MOBY D/E/I” Programs
4.5.4
Address Setup
This function defines the call of the “read/write MDS” commands.
S Start address +
S Read/Write
Length: Entry of the MDS address for the read/ write command uses a start address and the length of the data to be processed.
End address: Entry of the MDS address for the read/ write command uses a start address and an end address.
Switching from “block” to “complete MDS” takes place here. This setting affects the default setting for execution of an MDS command.
Block: When an MDS is read/written, the currently active area is always indicated as the area to be read/written.
Complete MDS: When an MDS is read/written, the entire MDS is always processed.
The read/write function is started immediately. Partial MDS areas cannot be entered.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-27
The “MOBY D/E/I” Programs R 05/07
4.5.5
MOBY I Setup
S Mem size:
S Tag type:
S ECC:
S MDS507:
S Sample rate:
Specifies the memory size of the MDS to be processed
This setting also defines the memory area in the editor.
MDS memory addresses which exceed the memory size cannot be addressed.
Distinguishes between RAM/FRAM and EEPROM
The RAM/FRAM setting shows an empty MDS support battery on the STG hand-held terminal PRO.
Turns the ECC driver on and off
The purpose of the ECC driver is described in the documentation of the MOBY interface.
This parameter must only be set to “yes” when the
MDS 507 is used. With the MDS 507, the dialog battery is scanned and indicated as “Status” when it is empty.
The scan time is only relevant when the MDS 507 is used with an ASM 420. The setting range is 0.1 sec to
6.3 sec. The default value (0.5 sec) usually does not have to be changed.
4.5.6
MOBY E Setup
S Key A/B:
S Mode:
S Antenna:
You can switch between the “MOBY key” and the
“B transport key for MIFARE data memory.”
The MOBY key is always standard. The “B” setting permits the MIFARE MDS to be processed in its status on delivery. (The B key must be in its original state.)
Only for MOBY E SIM (cf. chapter 6.5):
Switches the SIM from cyclic mode to continuous mode.
Command processing is much faster in continuous mode.
You can switch between card and pill.
E-28
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07
4.6
The “?” Functions
The “MOBY D/E/I” Programs
4.6.1
Language
German or English can be selected as the menu language with the STG.
During commissioning of the STG, the default language is English.
4.6.2
About
Information on the manufacturer of the STG program:
Siemens AG A&D SC FS
4.6.3
Version
Specifies the version of the STG program, the EPOC emulated operating system, the release status of the emulated ROM version and the release status of the MOBY library. These parameters must be specified when reporting errors to Siemens.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-29
The “FILEHANDLER” Program R 05/07
5 The “FILEHANDLER” Program
5.1
General Information on the Filehandler
As with any PC-based system, the filehandler accesses the data with logical file names and not with physical memory addresses.
The following figure shows the layout of the “FILEHANDLER” program and how it works.
Files on hand-held terminal
File 3.hex
File 2.hex
File 1.hex
Directory display
Files on MDS
File 3
File 2
File 1
Optional connection on the PC
WORD
EXCEL
.
.
Editor display
MOBY\File 3.hex
MOBY\File 2.hex
MOBY\File 1.hex
E-30
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “FILEHANDLER” Program
The “FILEHANDLER” program is designed so that you can use the same functions to access the files on the hand-held terminal and the files on the MDS.
The directory display is available for both the hand-held terminal and the MDS.
MDS files can be copied from the MDS to the hand-held terminal (and vice versa) with just a few keys.
An optional connection to the PC permits you to exchange files stored on the hand-held terminal with the PC.
You can then process the data with your familiar PC programs (e.g., WORD,
EXCEL, and so on). Prerequisite: The PC application must support the con-
tents and data structure of the MDS file. See also chapter 6.
Note
Remember that the filehandler is only available for the MOBY I.
5.2
The Filehandler Commands
STG Command
File/Read File from
Tag
File/Read File from
STG RAM
File/Write File to Tag
S
W
File/Write File to STG
RAM
T
File/Read Dir from Tag G
Shortcut 1 Filehandler
Command
R or Enter READ
–
WRITE
–
DIR
File/rRad Dir from STG
RAM
File/exit
P
X
Commands/Create
File
B
Commands/Delete File D or Del 2
Commands/Tag Format
I
Commands/File Attribute
Y
Commands/Tag Status F
–
–
CREATE
DELETE
FORMAT
ATTRIB
Description
Read a file from the MDS
Read a file from the RAM of the hand-held terminal
Write a file to the MDS
Write the data from the editor to the hand-held terminal
Read directory from the MDS and indicate
Indicate directory of the STG
(RAM memory)
Exit filehandler application
Create new file with length of
0 on the MDS
Delete file from the MDS
Format the MDS
Assign access rights to file on the MDS
MDS STATUS Read MDS status
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-31
The “FILEHANDLER” Program R 05/07
STG Command
Commands/Cover Tag C
Editor/Display Directory
Editor/Display Editor
Editor/File Size
Editor/Clear Display
Editor/
Jump to address
Editor/Display Setup
Q
Extras/Parameter
Extras/Password for
FH
Extras/Communication E
Z
A
?/Language L
?/About...
?/Version
K
V
U
N
J
Shortcut 1
O or Tab
H
–
–
–
–
–
–
–
–
–
Filehandler
Command
COVER
–
–
–
Description
Protect data structure of the
MDS
Display last read directory
Display file data
Change file size in editor
Write display with certain value
Move cursor to address position
Switch display between
ASCII and HEX representation
Set filehandler parameters
Password setting for the
“FILEHANDLER” program
Setting: Read head or ASM
Set menu language
Manufacturer’s data
Version of operating system and filehandler
1 The key combination ALT + key is used for the shortcuts of the commands. Both keys must be pressed one after the other. The keys for the shortcuts of the MDS commands are the same as the letters used to address them in the SIMATIC with FC.
2 The
“
Del” key can be used to delete the file currently selected in the directory view. This can also be used to delete files from the RAM of the hand-held terminal.
E-32
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “FILEHANDLER” Program
5.3
View of the Editor and Directory
The filehandler’s monitor screen display is either “Directory – View” or “Editor –
View.” You can use the menu “Editor/Display Editor” and “Editor/Display Directory” menu to switch between the two displays.
5.3.1
The Data Editor of the Filehandler
The design of the data editor of the filehandler is similar to the standard STG
Set MDS memory size. It can be set with the command Extras/Parameter.
Name of the file in the editor. The file can have been read by both the MDS and the hand-held terminal memory.
The file length is shown here.
The piece of data on which the cursor is located. Is also shown in ASCII format.
If the file size is too long (see
chap. 5.6.3), the extra data are shown
inverted.
The data area which is longer than the file length is marked with the data string
“ eof” (end-of-file).
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-33
The “FILEHANDLER” Program R 05/07
5.3.2
View of the Directory
The directory view shows either all files of the MDS or all files of the STG RAM.
The directory view makes it very easy to read files from the MDS or copy files
between hand-held terminal and MDS. See chapter 5.4.
Layout of the directory
Indication of whether the displayed directory is from an terminal”
“ MDS” or from the “ hand-held
Name with which the MDS was formatted.
No name is indicated for the hand-held terminal’s directory.
Free memory on the MDS. With the handheld terminal, this is approx. 40 MB (after the terminal has been commissioned).
A file can be selected with the cursor keys. After selection, a function can then be directly executed with this file. See
An attribute can be entered here for the
MDS files (see chap. 5.5.4). No attributes
can be set for hand-held terminal files.
E-34
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “FILEHANDLER” Program
5.4
The File Menu
The file menu primarily contains three functions which can be called.
S Read file
S Write file
S Read and display directory
These functions can be executed on both the MDS and the internal memory of the hand-held terminal.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-35
The “FILEHANDLER” Program R 05/07
5.4.1
Read File from MDS (Read File from Tag)
After this function has been called, a menu appears in which you can select a file with the cursor keys. All file names can be scrolled through, including the
ones in the directory view (see chap. 5.3.2).
After you have scrolled through all the files, the file name “New Tag DIR” appears. If you press the Enter key, the filehandler reads a directory from an MDS.
You can then select one of the new files
If you continue paging through the file selection menu until the file name “Other File” appears, you can enter a file name (with the
ASCII keyboard of the hand-held terminal) in the menu which appears.
5.4.2
Read File from STG RAM
After this function is called, a menu appears in which you can select a file with the cursor keys. All file names in the RAM of the hand-held terminal with the file extension .HEX are displayed. If the STG RAM does not contain any files with the extension .HEX, the message “No file available” appears.
E-36
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “FILEHANDLER” Program
5.4.3
Write File to MDS (Write File to Tag)
The file name is entered as described in chapter 5.4.1. After a file name con-
tained in the directory is entered, you are given the following choices.
You can overwrite the file or append the new data to the existing file.
In the next screen, you can still change the length of the data to be written.
The default length is always given as the value of the length of the data in the editor. If you change the default length, the data length on the MDS will also be adjusted.
If you selected the “Append” data option, the file is automatically read again after execution of the write function. This gives you the complete updated file on the editor.
If you selected the file name “Other File” when you called the write function and entered a new file name with the keyboard, the “Create” screen appears.
If you confirm this screen with “Yes,” a new file is created on the MDS before the data are written to the MDS.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-37
The “FILEHANDLER” Program R 05/07
5.4.4
Write File to STG RAM
When a file is saved, the file name indicated in the editor is also indicated as the default name. You can still change the file name before saving the file. The file name may contain up to 8 characters. When the file is saved, the file extension .HEX is automatically added to the file name.
5.4.5
Read Directory from MDS (Read Dir from Tag)
The file directory of an MDS is read and indicated on the display in the directory
view (see chap. 5.3.2). With some MDS types, this may take several seconds.
5.4.6
Read Directory from STG RAM (Read Dir from
STG RAM)
The file directory of the hand-held terminal’s RAM /PSION/M is read and indi-
cated on the display in the directory view (see chap. 5.3.2). Only type *.HEX
files are shown on the display. Also, only files located in the root directory of the hand-held terminal’s RAM are indicated on the display.
E-38
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “FILEHANDLER” Program
5.4.7
Example: Copy Files
The functions described in this chapter make it very easy to copy files. Files can be copied from MDS to MDS or from STG RAM to MDS. The procedure for copying a file from a first MDS to a second MDS will now be described:
1. The function “File/Read Dir from Tag” (ALT + G) is executed.
2. The cursor keys select the file to be read.
3. Press “Enter”. After being read, the data are displayed in the editor screen.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-39
The “FILEHANDLER” Program
4. The “File/Write File to Tag” function (ALT + W) is executed.
5. Select filename “colour”
6. Accept overwrite
7. Accept length
R 05/07
After these functions have been executed, the “delivery” file is copied to “colour.”
The “colour” file now also appears with a size of 300 bytes.
E-40
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “FILEHANDLER” Program
5.5
The Commands Menu
The “Commands” menu contains only commands related to the MDS memory.
5.5.1
New File (Create File)
“Create File” is used to set up a new file on the MDS. The file name may not yet exist on the MDS. The new file is always given a length of 0.
5.5.2
Delete File
This function deletes a file from the MDS memory.
If you are in the directory view, it is very easy to start the delete function by pressing the “Del” key. You can use the “Del” key to delete files from the MDS or the hand-held terminal. The files are deleted from the hand-held terminal if the STG files are being shown in the directory view.
5.5.3
Format MDS (Tag Format)
Before it can be used with the filehandler, the MDS must be formatted. Before formatting, it is important to set the memory size of the MDS correctly. Use the
Extras/Parameter function for this. Formatting deletes all data from the MDS, and a new file structure is set up.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-41
The “FILEHANDLER” Program R 05/07
5.5.4
Attribute File (File Attribute)
This command can be used to assign access rights to the individual files. This protects the files from unauthorized and unintentional overwriting. The direc-
tory view shows the file attribute in the right-hand column (see chap. 5.3.2).
The following file attributes are available.
Attribute
–
R
W
F
F/R
Description
No attribute or an existing attribute is deleted.
Read only. The file can only be read. It cannot be written, overwritten or deleted.
Write once. The file can be written once. The file cannot be written again. It also cannot be deleted.
Fixed length. The file can be read as often as desired. It can only be written when this does not change the length of the file. Data cannot be appended, and the file cannot be deleted.
“ Fixed length” and “ read only” are set. This attribute has the same effect as the “ R” attribute.
File attributes can only be assigned to MDS files. Files on the RAM of the hand-held terminal always have the type “–” (i.e., they can always be changed or deleted).
E-42
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “FILEHANDLER” Program
5.5.5
MDS Status (Tag Status)
This command shows the status of the MDS in several consecutive screens.
MDS type (Tag type)
This value is identical to the specification of the
MDS type with the Format command on a SIMATIC.
Gross MDS size (Tag whole size)
The size of the MDS which was set with the Format command is indicated.
ECC
Indicates whether the MDS is used with or without
ECC
MDS (Tag)
Indicates the name of the MDS which was written to the MDS with the Format command
MDS size (Tag size)
Indicates the maximum memory area which can be used by the user
Bytes free
Indicates the number of data bytes on the MDS which the user can still use for his/her data
Directory free (Dir free)
Indicates the number of files which can still be set up on the MDS
Battery 1 (Bat1)
Status of the RAM battery. This value does not apply to the EEPROM MDS.
Battery 2 (Bat2)
Status of the dialog battery with MDS 507
Amount of processing (Work Counter)
Number of processing procedures which were performed with the MDS since it was initially formatted.
This value is particularly important for the EEPROM
MDS since the number of write-accesses is limited for these types of memory.
ECC Correct
Counter for the number of ECC offsets performed.
If this counter has a value other than zero, the MDS must be replaced in the near future. An EEPROM memory was write-accessed too often.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-43
The “FILEHANDLER” Program R 05/07
5.5.6
MDS Cover
The Cover command protects the entire file structure on the MDS. If an MDS is
“covered”:
S Every file can be read.
S Every file can be written as long as the file length is not changed.
S No files can be deleted.
S No new files can be created.
S The format of the MDS can be initialized again. This “uncovers” the MDS.
S The “covered” state can be canceled with a Cover command and the setting
“not covered.”
5.6
The Editor Menu
5.6.1
Display Directory
This function switches the display to the directory view (see chap. 5.3.2). The
directory which was read last is displayed. The directory can be from the MDS or the hand-held terminal.
E-44
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “FILEHANDLER” Program
5.6.2
Display Editor
This function switches the display to the editor view (see chap. 5.3.1). The dis-
play shows the file which was read last. This file can be from the MDS or the hand-held terminal.
5.6.3
Change File Size (File Size)
The editor shows the current size of a file in the second line. This length can be modified with the “File Size” command. When the file is made longer, an appropriate number of zeros (00 Hex) is appended to the end of the file. The editor shows the appended portion with inverted digits.
5.6.4
Delete Display (Clear Display)
This function clears the memory of the editor display. The hexadecimal value of the filler character can be specified. The standard filler character is 00hex.
After deletion, all data in the display are shown inverted to indicate that no data have been entered yet by the user.
5.6.5
Jump to Address
Normally the cursor is positioned within a file with the four cursor keys. With large files, it is much quicker to use the “jump to address” function to position the cursor anywhere within the file. You can also call the “jump to address” function very easily with the Tab key.
5.6.6
Display Setup
The display is set here. You can choose either hexadecimal or ASCII format.
In ASCII format, the characters which cannot be shown appear as white fields.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-45
The “FILEHANDLER” Program
5.7
The Extras Menu
R 05/07
5.7.1
Parameter
The “parameter” function is used to make the basic settings for the filehandler.
Parameter Description
MDS size The gross memory size of the MDS is set here.
MDS type
ECC
SLG no.
(hex)
EAKO
This memory size is shown in the first line of the display. The Format command uses the memory size to specify the file system. If the
“MDS size” parameter does not correspond to the MDS being used, the MDS can still be used. Only the Format command would produce the wrong result.
Here you can switch between RAM, EEPROM and MDS 507. FRAM memory is treated as RAM memory. If EEPROM is selected, the battery error message is suppressed on the display since these MDSs do not have batteries. If MDS 507 is selected, the dialog battery is also evaluated. When empty, this is shown on the display.
Activate/deactivate ECC driver
When an MDS is processed, the SLG no. selected here is written to the system area of the MDS. It has no effect on the function of the Filehandler program on the STG hand-held terminal PRO.
The entry/exit check cannot be set on the STG hand-held terminal
PRO with the filehandler. The STG hand-held terminal PRO does not use entry/exit control (AEKO = 4).
E-46
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 The “FILEHANDLER” Program
5.7.2
Password for Filehandler (Password for FH)
The filehandler password protects the STG hand-held terminal PRO data on the MDS from being manipulated by unauthorized parties. The passwords for
the “Filehandler” and “MOBY D/E/I” programs are identical. See chapter 4.5.2
for a description of how to handle the password.
5.7.3
Communication
In principle, communication of the filehandler is always set to “read head.”
However, the filehandler can be changed to “ASM on RS 232” as an option. A type “ASM420-RS232” module can then be connected to the hand-held termi-
nal. For more information, see chapter 6.5.
Remember that a type “ASM 421” module cannot be used with the STG handheld terminal PRO.
5.8
The “?” Functions
These functions are the same as those of the “MOBY D/E/I” programs. See
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-47
Expanded Functions R 05/07
6 Expanded Functions
6.1
Storing the MDS Data on the STG Hand-Held
Terminal PRO
The data read from the MDS are automatically stored on the hand-held terminal in a file named “READ_D.HEX,” “READ_E.HEX” or “READ_I.HEX” in the folder
/SIBO/M of the PSION Workabout PRO. Every additional read command overwrites this file.
When the MDS is write-accessed, the write data are written from the editor to the MDS and also to the folder /SIBO/M on the PSION Workabout PRO under the name “WRITE_D.HEX,” “WRITE_E.HEX” or “WRITE_I.HEX.” Every additional write command overwrites this file.
You can load a previously stored file into the editor using the “file/load file” function. To do this, enter the name of the file without the suffix “.HEX.”
You can also call up a list of the stored files by leaving the entry field blank and pressing the ENTER key.
You can now select the corresponding file using the cursor keys.
The “file/save” function stores the data of the editor in a file with the file extension “.HEX” and at the same time the ID number in a file with the file suffix
“.HX1” in the folder /SIBO/M/HX on the PSION Workabout PRO. You can specify any name of 1 to 8 alphanumeric characters.
Note
When you read data from the MDS, modify data in the editor and then save the data, the modified data will be stored in the .HEX file.
E-48
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Expanded Functions
6.2
Copying MOBY Data from and to the
STG Hand-Held Terminal PRO
6.2.1
What Is Needed in Addition?
S Workabout PRO docking station (Order number see catalog)
S USB Driver for STG hand-held terminal PRO
Is included on CD “RFID Systems Software & Documentation” from product version 07/2007 (Order number 6GT2080-2AA10)
S Active Sync program Version 3.4 or higher
Note
Download of Microsoft Active Sync
Microsoft Active Sync is not part of the scope of supply. However, the current version of the application can be downloaded from www.microsoft.com.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-49
Expanded Functions R 05/07
6.2.2
Installing procedure
1. Install Microsoft Active Sync on the PC
2. Install a USB driver STG Hand-Held Terminal PRO on the PC
3. Establish a partnership between the PC and the STG Hand-Held Terminal
PRO
Install Microsoft Active Sync on the PC
With Microsoft Active Sync, you can synchronize files between your PC and the
STG Hand-Held Terminal PRO and transfer applications to the reader. With an
Active Sync connection, the MOBY Workabaout PRO can be accessed as a drive in Windows Explorer under “Mobile Device”. For further information on
Microsoft Active Sync, see the accompanying help file.
If Microsoft Active Sync is not installed on your PC or if an earlier version than
3.4 is installed, you should install the current version available from Microsoft.
Notice
Update / Installation of Microsoft Active Sync
Before you update or install Microsoft Active Sync, you must deinstall the old version.
Proceed as follows when installing Microsoft Active Sync:
1. Start the installation program by double-clicking the file msasync.exe.
2. Follow the instructions on the screen.
Note
Standard Sync Folder
When installation has been completed, Microsoft Active Sync creates the folder Workabout Pro My Documents on the desktop of your PC.
In the Active Sync settings menu under Sync Options, when you select the option Data, the content of the desktop folder is synchronized on the reader for every Active Sync procedure with the content of the folder My Documents on the reader.
E-50
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Expanded Functions
Install a USB driver for STG Hand-Held Terminal PRO on the PC
Note
Windows XP: Ignore compatibility test
During installation of the USB driver under Windows XP, a message may be displayed indicating that the driver has failed the compatibility test. Ignore this message and proceed with the installation.
Proceed as follows to install the USB driver for the STG Hand-Held Terminal
PRO:
1. Connect the STG Hand-Held Terminal PRO to a spare USB port of your PC through the USB cradle.
2. Switch the STG Hand-Held Terminal PRO on.
3. Insert the CD RFID Systeme Software & Dokumentation in the drive of your PC.
4. Start the installation program by double-clicking the file \daten\STG_PRO\
USB_Driver\usbsetup.exe.
5. Under Select Device, select the option Workabout Pro.
6. Follow the instructions on the screen.
Establish a partnership between the PC and the STG Hand-Held Terminal PRO
A relationship must be established between the PC and the reader so that
Microsoft Active Sync recognizes the STG Hand-Held Terminal PRO.
1. Proceed as follows to establish the partnership:
2. Connect the STG Hand-Held Terminal PRO to a spare USB port of your PC through the USB cradle.
3. Switch the STG Hand-Held Terminal PRO on.
4. Microsoft Active Sync starts automatically and recognizes the reader as a new device. Answer the prompt as to whether a partnership should be established between the PC and the reader with Yes.
5. Follow the instructions on the screen.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-51
Expanded Functions R 05/07
6.2.3
Data exchange
Requirement:
A partnership is established between STG Hand-Held Terminal PRO and PC.
STG Hand-Held Terminal PRO is seated in docking station and switched on.
In Windows Explorer you see a new Icon “Mobile Device”. With double clicking you get the filesystem of your STG Hand-Held Terminal PRO.
Alternativly you could Open ActiveSync program and press “Explore” button, or select menu “File/Explore”.
Open the file tree of STG Hand-Held Terminal PRO by double-clicking the SIBO folder, and than the Folder M. There you will find, among others, the
“READ_D/E/I.HEX” file and the files which you stored with the extension
“.HEX.” Now drag and drop or copy these files from the STG Hand-Held Terminal PRO drive to the PC drive.
E-52
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Expanded Functions
The length of the READ or WRITE file is the same as that of the MDS which was read.
READ_D.HEX: 44 bytes for I-Code1
112 bytes for I-Code SLI
256 bytes for Tag-it HF-I
992 bytes for my-d
READ_E.HEX: 768 bytes for MOBY E (in normal mode)
1024 bytes for MOBY E (after reading the raw data)
1024 bytes for MOBY E (in SIM mode)
READ_I.HEX:
Setup Setting
62 bytes
128 bytes
2 KB
8 KB
32 KB
No ECC
62
128
2045
8189
32765
With ECC
42
112
1778
7154
28658
The contents of the file can now be indicated and changed with an appropriate editor on your PC.
When ASCII data were read from the MDS:
Any editor can be used (e.g., NOTEPAD, WRITE, WORD and so on).
When binary data were exchanged with the MDS:
Use a HEX editor. HEX editors are available on the shareware market
(e.g., Hedit and so on) or on the professional market (e.g., Codewright).
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-53
Expanded Functions R 05/07
6.2.4
Organization of the READ.HEX File
The READ_x.HEX file only contains the pure data which also exist on the MDS.
The length of the file is the same as that of the MDS, specified in bytes.
6.2.5
Organization of the READ.HX1 File
The READ_x.HX1 file contains the ID number. The READ_x.HX1 file is only created for MOBY D/E.
6.3
Functions with the PSION Operating System
You can use the FILE/EXIT menu command to access the operating system level of the hand-held terminal. We will now describe some of the functions which are available with the Windows CE operating system.
Note
This functionality is only in Supervisor mode available see chapter 6.5.1.
S Setup and Configuration of STG Hand-Held Terminal PRO
S Edit the read MOBY data with the PSION editor. Remember that this editor can only be used when the MDS data are in ASCII format.
S Spread sheet function
S Calculator
S Execution of commands
See the manual entitled “Psion Teklogix Workabout PRO Hand-Held Computer
User Manual” for a detailed description of operating system functions and stan-
dard programs. This manual can be ordered from PSION. See appendix A.1.
E-54
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Expanded Functions
6.4
Automatic Power Saver Function
The PSION Workabout PRO has an automatic power saver function. This is activated after no keys have been pressed on the PSION Workabout PRO for approximately 5 minutes.
In addition, the “MOBY D/E/I” programs have another power saver function.
The MDS command being executed is interrupted if no MDS is detected
30 seconds after the start of an MDS command or the MDS being processed is moved out of the field for more than 30 seconds. The following message appears.
You can now completely terminate the command with ESC or continue with
ENTER. If you decide to continue, the interrupted command is continued at the point at which it was interrupted.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-55
Expanded Functions R 05/07
6.5
Connecting SIM Devices (MOBY E/I)
A MOBY E SIM can be connected to the RS 232 interface of the PSION Workabout PRO. The following figure shows the connection diagram. Before commissioning, a switch must be made to MOBY E/SIM or ASM 420/I with the
“EXTRAS/COMMUNICATION/PROTOCOL” function.
With this configuration, SIM can be used to work with the “MOBY” program and
user applications with the MOBY library. Cf. appendix A.2.
MOBY E/SIM:
Cable (6GT2391-1DH50) and
Power pack (6GT2090-0HB00)
AC 220 V
DC 24 V
Note
Since the standard SIM of MOBY E uses cyclic operation, it takes much, much longer to process a read/write command than with the
STG read head. The EXTRAS/MOBY E Setup/MODE command can be used to switch the SIM to the faster read mode. This command must be repeated each time SIM is turned on.
E-56
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Expanded Functions
ASM 420/I:
This settings permits an ASM 420/RS 232 to be connected to the hand-held terminal. The connection cable must comply with the specifications in the
ASM 420 documentation. In ASM 420 mode, the MOBY V driver is always enabled during the “MOBY I” program. SLG 65 can be used on the ASM 420 with this.
Use of MOBY I SLGs is limited.
Assignment of the RS 232 interface on the hand-held terminal:
2
3
5
Pin Designation
TxD
RxD
Gnd
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-57
Expanded Functions R 05/07
6.5.1
Security
The STG Hand-Held Terminal PRO has two security states:
S Supervisor
For configuration and setup of STG Hand-Held Terminal PRO.
Not necessary if MOBY Service and test application is used.
S User
Default state. User can only use preinstalled service and test application.
Start menu functionality is limited.
The security state could be changed via the security menu.
This menu is accessible via the windows start menu. The start menu itself is started inside the MOBY service and test application with the key combination
“CTRL” + “ESC”.
Change to Supervisor is protected with password. At delivery password is set to
123456. Password should be changed at first use.
E-58
Notice
Be aware not to delete or manupilate files in folder “\Flash Disk”.
Files with extension “*.pfl” include the backup information of the delivery version. When you change into supervisor mode, please make a backup of this file first and store it at a secure place. You could reset your STG Hand-Held Terminal PRO device to the delivery state, if you copy your backupfile into folder “\Flash Disk” and performe a
system reset (see chapter 6.6).
Note
If the files with the endings “.PFL” are damaged or have got lost the original state of the device can only be restored in the factory.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Expanded Functions
6.6
System RESET
The hand-held terminal executes a system RESET when the device is turned on for the first time after the batteries have been installed. This RESET is the same as a hardware RESET.
A system RESET can also be triggered by hand. To do this, change STG
Hand-Held Terminal PRO in supervisor mode. See chapter 6.5.1. Than acti-
vate the function “Cold Reset” via start menu/Shutdown.
During the system RESET:
S Data stored in flash memory are always retained (“Flash Disk”).
S The data in RAM memory are lost.
Be aware that your password for supervisor mode is also reseted and has to be initialized again.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-59
Error Messages R 05/07
7 Error Messages
What to do when ...
... The PSION display goes blank during MOBY read/write.
S The batteries of the PSION Workabout PRO are empty. Insert device in the charging shell, or install new batteries.
... The display remains blank after the device is turned on.
S The batteries are empty.
7.1
Error Messages with the “MOBY D/E/I”
Programs
The messages in the following tables can occur during operation. The messages are indicated in a separate window. A message can have the following format.
Type of error
Exact error designation
The message is coded in several digits, has the format is xx/yy/zz, and is used for precise error analysis. The following tables list the types of errors and the error designations in detail. The information in /zz is included in some messages. “zz” contains additional error information (e.g., the block in which the error occurred).
Type of Error
1 to 2
3 to 9
10 to 15
20
30 to 37
42 to 45
52 to 57
60 to 72
Description
General errors
MOBY E errors reserved
Timer errors
MOBY I errors
MOBY D errors
MOBY D ISO errors reserved
E-60
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Error Messages
Error Designation Possible Causes and Their Correction
1, 2, 3, 4, 5, 6
7
10, 11, 12
20
21
22 to 27
32
33, 34, 35, 36
37
38
S Reader device fails to send start protocol.
S Is read head screwed on?
S Does the read head match the protocol setting? (See menu: Extras/COMMUNICATION.)
S Batteries in the reader device are dead. (The batteries may be defective.)
S Internal program error
Interface defective
Reader device doesn’t answer at all or sends an incorrect answer (MDS D1xx/MDS F4xx).
S Reader device doesn’t answer.
S Check parameters in the Extras/COMMUNICATION menu.
With SIM mode, “Interface” and “Protocol” must both be set to SIM.
S Batteries in the reader device are empty. (The batteries may be defective.)
Reader device doesn’t answer at all or sends an incorrect answer.
S Internal program error (MDS D1xx)
S Reader device sends the wrong answer.
S MDS is not personalized with the MOBY key.
S Internal program error (MDS D1xx/MDS F4xx)
Illegal request, internal program error
S Check contact to read head.
S Read device doesn’t answer (MDS E6xx)
Internal program error
S Exit STG program, and start again.
S Read/write error (MDS F4xx)
S Read head gives you an error message.
S Read head is faulty.
S CRC error of MDS. Communication error to MDS. MDS is located on the boundary.
S MDS has a defect.
S Internal program error
Specified block is write-protected.
39 Several MDSs are in the field.
S Internal program error (MDS D1xx)
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-61
Error Messages R 05/07
Error Designation Possible Causes and Their Correction
40, 41, 42
43
45
Reader device doesn’t answer at all or sends an incorrect answer (MDS D1xx).
S Internal program error (MDS D1xx)
User termination with ESC
Wrong answer from read device
50
52, 53, 54, 55,
56, 57
63
Error while reading or writing the MDS data
Internal program error on MOBY read head
65
66
67
70
80
81, 82
101 to 132
S Write not successful
S Several tags in the field
MDS type on reader device is not supported.
S Read device sends wrong answer.
S MDS not personalized with MOBY key
Read device sent error (MOBY I).
Specification of certain errors:
101
Authentication error. The MDS doesn’t have the MOBY key.
S Try setting the “B” key under “Extras/MOBY E Setup.”
Interface error. Appears when a SIM is connected.
S Check parameters in the “Extras/COMMUNICATION” menu.
S Check plug and cable to SIM.
General read/write error on MOBY read head
Internal program error on MOBY read head
103
104
105
106
Presence error
S No MDS in the field which has the MDS ID number contained in the command.
Error in the connection to the SLG
S Read head hardware has a defect.
Error in MDS memory
S Execute INIT command. Before executing this command, make sure that the memory size of the MDS is set correctly under “Extras/MOBY I Setup.”
S The MDS is defective.
MOBY command cannot be interpreted by the read head.
S Check the memory size under “Extras/MOBY I Setup.”
S Field interference on read head. External interference.
S The MDS left the field during communication.
S Field interference during communication
E-62
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Error Messages
Error Designation Possible Causes and Their Correction
107
109
110
Too many sending errors. The MDS wasn’t able to correctly receive the data from the read head.
S The MDS is located in the boundary area of the read head.
CRC error due to field interference while initializing the MDS
MDS cannot be initialized and is defective.
111
112
113
114
115
125
129
130
180 to 243
Timeout during initialization (MOBY I)
S The MDS is located in the boundary area of the read head.
S An MDS 507 is initialized but MDS 507 mode has not been enabled under “Extras/MOBY I Setup.”
S The MDS memory cannot be written and is defective.
S The OTP memory cannot be written again.
The address area of the MDS was exceeded.
S Check the memory size under “Extras/MOBY I Setup.”
ECC error or MDS not initialized in ECC mode
S Enable ECC mode under “Extras/MOBY I Setup,” and then execute the INIT command.
Reset message after return of power
S The hand-held terminal has a defect in the power supply to the read head. (Try charging/replacing the batteries.)
S The hardware of the read head has a defect.
Internal program error. Previous command is active.
The number of MDSs in the field is not permitted. Number of
MDS > multitag in the “SLG Status” function under “Extras.”
Internal program error. The telegram layout of the command to the read head is wrong.
Internal program error (MDS D1xx)
251
255
Turn the device off and on again. If error continues to occur, contact Customer Support and specify the error number.
Read/write comparison not successful
No card/no MDS in the field
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-63
Error Messages R 05/07
7.2
Error Messages with the “FILEHANDLER”
Program
The following table lists the messages which can occur with the filehandler. A filehandler error message looks like this.
Type of error
Exact filehandler error
The filehandler error is shown in the same way as the filehandler on the SIMATIC. The error message has one alpha character followed by a 3-position number. Most of the error codes are identical with the error numbers of all MOBY filehandler interfaces.
Type of
Error
C009
C010
C011
C012
C013
C014
C015
C016
C017
Filehandler
Error
A006
A011
A015
A016
A020
B001
C002
C006
C007
C008
Description of Error, Its Cause and Correction
Unknown command. Command identifier KK is illegal.
With 1st command block: DBN not 1
With next block: KK or DBN incorrect
Checkbyte error while receiving from S5
Command from other sender is being processed.
Wrong number of characters in the telegram
Error in the connection to the SLG
Read head defective
Error on RAM of the MDS. Replace MDS and perform
FORMAT.
Presence error. MDS in boundary area.
Parameterization error during FORMAT. Command cannot be interpreted.
Too many sync attempts. Field interference on read head.
Too many sending errors
CRC sending error
FORMAT. CRC error while receiving.
FORMAT. MDS cannot be initialized.
FORMAT, timeout. MDS in boundary area.
FORMAT, not initialized. Check Extras/Parameter.
CMD address error. Check Extras/Parameter.
ECC error. Format MDS again. Disable ECC mode.
General driver error
Protocol errors
SLG errors
MDS errors
E-64
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Error Messages
H140
H141
H142
H143
H144
H145
H146
H147
H148
H149
H150
H151
H152
H153
Filehandler
Error
D001
D005
D009
D014
D015
D018
D022
D023
E001
E002
E003
E005
F001
F005
Description of Error, Its Cause and Correction
Only RESET command permitted
Illegal parameters for FORMAT, CREATE, WRITE,
UPDATE or ATTRIB
RESET command parameter wrong
CREATE and WRITE: The user data area of the MDS is completely full.
Only FORMAT command possible. MDS not identified.
Start address in the command is outside the data area
(i.e., start address > file length).
Directory and/or FAT. Modifying an MDS protected with
COVER is illegal.
COVER: MDS name wrong
MDS type is wrong or doesn’t match the set mode
(ECC).
CREATE command: No more directory entries free
CREATE command: File already exists in the directory.
READ or WRITE: A FAT block sequence error was determined. The FAT is defective.
The addressed file does not exist.
WRITE/UPDATE/DELETE command for a file which is protected with the appropriate attribute
Serial interface error
Wrong interface
Faulty timer
Interface error
Start-protocol error
Reset error, WRITE
Reset error, READ, no STX
Reset error, READ, timeout
Reset error, READ, wrong response
Start error, WRITE
Start error, READ, no STX
Start error, READ, timeout
Start error, READ, wrong response
Start error, WRITE, length too long
Type of
Error
Job related errors
Directoryrelated errors
File-related errors
Error messages of the filehandler
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-65
Technical Data R 05/07
8 Technical Data
Hardware
Processor
RAM memory
ROM memory
Monitor screen
Keyboard
Touch
Sound
Intel XScale PXA
128 Mbytes of which approx. 40 Mbytes can be used as desired
64 Mbytes for operating system and Flash Disk.
Approx. 40 Mbytes can be used as disired
Graphic LCD monitor screen with 240 x 320 pixels, color
Alphanumeric
Touchscreen finger operation
Internal speaker
Power supply
Interfaces
Lithium Ion rechargeable battery
High-speed chargeable, automatic switch-off
Operation time: ca. 20 hours
(Read head inactive, display not lighted)
8 hours
(Read head active)
Backup battery: 3 V lithium Ion rechargeable coin battery
LIF interface (LIF = Low Insertion Force) for battery charging and communication with PC
RS 232 and TTL interface for connection of a MOBY read head
Software
Operating system Windows CE 4.2 with SIBO C Emulation
File management
Integrated software
Windows compatible
MOBY service and test program
E-66
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Technical Data
Technical Data
Dimensions
Weight
Temperature
Relative humidity
Protection rating
Shock resistance
EMC
Complete Device
(incl. Batteries)
90 x 305 x 44 [mm]
Read Head
90 x 64 x 35 [mm]
Approx. 460 g Approx. 100 g
Operation: –10 ° C
Storage: –25 ° C to +60 ° C (without batteries)
5% to 90%, no condensation
IP54 (protected against splashed water) 1
Max. falling height on concrete: 1,2 m
EN 55022, EN 55024
1 With STG U hand-held terminal, only for complete device with PSION Workabout PRO
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-67
Technical Data R 05/07
RF read/write head
MOBY D
MOBY E
MOBY I
13.56 MHz (I-Code; Tag-it)
Max. read distance: 60 mm with MDS D139
25 mm with MDS D160
30 mm with MDS D124
Labels based on I-Code in standard size
(approx. 85 x 55 mm):
Max. read distance: 75 mm with I-Code1
100 mm with I-Code SLI
100 mm with Tag-it HF-I
100 mm with my-d
Certifications: ETS 300 330
13.56 MHz (MIFARE)
Max. read distance: 30 mm with MDS E611
18 mm with MDS E600
8mm with MDS E624
4mm with MDS E623
3mm with MDS E623, mounted in metal
Certifications: ETS 300 330 reg. no. G100213L
FCC ID: KR5MIS
1.81 MHz (data); 134 kHz (power)
MDS Type
401/402
404/514/413E
403
506
439E
507 with battery
507 without battery
Certifications:
Max. Read Distance
(in mm)
6
20
8
12
12
35
4
ETS 300 330 reg. no. TTI-P-G 128/96
FCC ID: KR5MIS-I
E-68
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Appendix
A Appendix
A.1
Ordering Components for Expanded
Functions
The expanded functions of the STG hand-held terminal PRO require components which are not available from Siemens A&D.
If you need these components for your MOBY application, please contact
PSION directly or its representative in your country. You will find addresses and order lists from PSION on the Internet under www.psionteklogix.com
.
The PSION representative in your country is also located under this Internet address.
The following components are required for the STG application as options.
Ordering Designation Remarks
Active Sync Also available free of charge under the Microsoft Internet address
User’s guide for PSION Workabout PRO Ask your PSION representative.
S High-speed charging devices
S PSION Workabout PRO with numeric keyboard
These components are not required for the STG application. They are only of importance if you want to program your own identification application on the hand-held terminal.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-69
Appendix R 05/07
A.2
Porting User Applications
User Applications based on successor MOBY STG devices could be ported to this devices.
Note
Development of complete new user applications are possible, but it is not recommendable. New projects should wait for the next generation of this devices.
What Do I Need?
The C development package from PSION and the empedded Visual Studio from Microsoft is required for user applications.
Package
USB Driver
Active Sync
PSION Teklogix
Mobile Device
SDK
Embedded
Visual C++ 4.0
SIBO_CandOP_ for_
WindowsCE_p5
Comment
Necessary to recognize STG
Hand-Held Terminal PRO on
PC at USB port
Communication between PC and
WinCE based device.
Software development kit for
Workabout PRO
Vendor
PSION
Teklogix
Microsoft
Where to get?
Internet: www.psionteklogix.com
RFID Systems Software &
Documentation
Internet:
1 www.microsoft.com/ downloads
PSION
Teklogix
Internet: www.psionteklogix.com
Developer Resources section of Teknet page
Microsoft Microsoft Development
Environement
(Compiler)
SIBO to Windows
CE Migration kit
PSION
Teklogix
Internet: www.psionteklogix.com
Developer Resources section of Teknet page
E-70
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Appendix
Package
MOBY.LIB
Comment
Interface to
MOBY RFID modules
1 Order number 6GT2080-2AA10
Vendor Where to get?
SIEMENS RFID Systems Software &
Documentation 1
For detailed description and possible restrictions please refer to “SIBO to Windows CE Migration kit”.
The MOBY Library
A library for MOBY D, MOBY E and MOBY I is available. The library
(MOBY D/E/I) is included on CD “RFID Systems Software & Documentation” from product version 07/2007 (order number 6GT2080-2AA10) . The C library also includes a description of the interface commands.
Please note that the library is not identical with the previous version on the basis of Workabout MX.
The following table summarizes the implemented commands.
The MOBY D Library
Function Call
RF_ReadBlock
RF_WriteBlock
RF_ReadTagId
RF_Status
RF_Init nMobyDOpen vMobyDClose
Short Description
Reads a block from the MDS
Writes a block
Selects the tag. Reads the TagId
Determines the tag type
Writes all user blocks
Opens an interface
Closes the opened interface
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-71
Appendix R 05/07
The tables below provide a summary of implemented commands.
The MOBY E Library
Function Call Short Description
CCT_READ_N_BLOCK Read card data (1 to n data blocks, max. of 96 bytes)
CCT_WRITE_N_BLOCK Write card data (1 to n data blocks, max. of 96 bytes)
CCT_WRITE_SIGNAL Address digital output, reserved for switching the antenna
CCT_OFF
CCT_MODE
CCT_OPEN
Turn off antenna field
Set field mode of the antenna field
Open logical device
Type of Command
Standard
Standard
Standard
Standard
Standard
CCT_CLOSE Close logical device
Only for
SIM operation via RS 232
Only for
SIM operation via RS 232
CCT_SETKEY Parameterize read-card/ write-card interface
Optional
CCT_SET_KEY_TEMP Change temporary key Optional
CCT_GET_FIELD_STATE Scan current card indices Optional
CCT_RESET Reset read head Optional - general command
Although the commands of the MOBY E library are the same as those of the standard MOBY E library “CCTWAPI,” not all commands of “CCTWAPI” are available on the hand-held terminal.
E-72
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
R 05/07 Appendix
The MOBY I Library (normal addressing of MDS)
Function Call moby_init moby_read moby_write moby_reset
Short Description
Initializes an MDS with a filler character from address 0 to the end address
Reads a data block from the MDS
Writes a data block to the MDS
Sends a reset command with parameterization to the read head moby_status nMobyIOpen
Sends a status command to the read head
Opens the interface and turns on the read head vMobyIClose Closes the opened interface. The read head is turned off.
nMobyIReadStartProtocol Reads the startup telegram from the read head
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 E-73
Appendix R 05/07
The MOBY I Library (filehandler addressing)
Function Call wFhRead wFhWrite wFhMdsStatus wFhAttrib wFhDelete wFhCreate wFhFormat wFhDir wFhCover wFhDirInfo nTagTypeFromTable lTagLenFromTable
Fhreset nFhOpenCom vFhCloseCom
Short Description
Reads a complete file from the MDS
Writes a file or appends data to a file
Sends a status command to the MDS
Sets a file attribute
Deletes a file from the MDS
Sets up a new file on the MDS
Formats an MDS
Reads a directory from the MDS
Protects the MDS file structure
Writes information from the “DIR” structure to the
“DirInfo” structure
Returns the MDS type from a table
Returns the MDS size from a table
Resets the filehandler
Opens the interface and turns on the read head
Closes the opened interface. The read head is turned off.
E-74
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
MOBY
STG Hand-Held Terminal PRO
Bedienungsanleitung
Inhaltsverzeichnis
Allgemeines
Die Inbetriebnahme des
STG Hand-Held Terminal PRO
Die Bedienung des
STG Hand-Held Terminal PRO
Die Programme
“MOBY D/E/I”
Das Programm
“FILEHANDLER”
Erweiterte Funktionen
Fehlermeldungen
Technische Daten
Anhang
(5)J31069-D0126-U001-A6-7418 erschienen im Mai 2007
Sicherheitshinweise
Dieses Handbuch enthält Hinweise, die Sie zu Ihrer persönlichen Sicherheit sowie zur Vermeidung von Sachschäden beachten müssen. Die Hinweise zu Ihrer persönlichen Sicherheit sind durch ein
Warndreieck hervorgehoben, Hinweise zu alleinigen Sachschäden stehen ohne Warndreieck. Je nach Gefährdungsstufe werden die Warnhinweise in abnehmender Reihenfolge wie folgt dargestellt.
!
Gefahr bedeutet, dass Tod oder schwere Körperverletzung eintreten wird , wenn die entsprechenden Vorsichtsmaßnahmen nicht getroffen werden.
!
Warnung bedeutet, dass Tod oder schwere Körperverletzung eintreten kann , wenn die entsprechenden Vorsichtsmaßnahmen nicht getroffen werden.
!
Vorsicht mit Warndreieck bedeutet, dass eine leichte Körperverletzung eintreten kann, wenn die entsprechenden Vorsichtsmaßnahmen nicht getroffen werden.
Vorsicht ohne Warndreieck bedeutet, dass Sachschaden eintreten kann, wenn die entsprechenden Vorsichtsmaßnahmen nicht getroffen werden.
Achtung bedeutet, dass ein unerwünschtes Ergebnis oder Zustand eintreten kann, wenn der entsprechende
Hinweis nicht beachtet wird.
Beim Auftreten mehrerer Gefährdungsstufen wird immer der Warnhinweis zur jeweils höchsten Stufe verwendet. Wenn in einem Warnhinweis mit dem Warndreieck vor Personenschäden gewarnt wird, dann kann im selben Warnhinweis zusätzlich eine Warnung vor Sachschäden angefügt sein.
Qualifiziertes Personal
Das zugehörige Gerät/System darf nur in Verbindung mit dieser Dokumentation eingerichtet und betrieben werden. Inbetriebsetzung und Betrieb eines Gerätes/Systems dürfen nur von qualifiziertem
Personal vorgenommen werden. Qualifiziertes Personal im Sinne der sicherheitstechnischen Hinweise dieser Dokumentation sind Personen, die die Berechtigung haben, Geräte, Systeme und
Stromkreise gemäß den Standards der Sicherheitstechnik in Betrieb zu nehmen, zu erden und zu kennzeichnen.
Bestimmungsgemäßer Gebrauch
Beachten Sie Folgendes:
!
Warnung
Das Gerät darf nur für die im Katalog und in der technischen Beschreibung vorgesehenen Einsatzfälle und nur in Verbindung mit von Siemens empfohlenen bzw. zugelassenen Fremdgeräten und
-komponenten verwendet werden. Der einwandfreie und sichere Betrieb des Produktes setzt sachgemäßen Transport, sachgemäße Lagerung, Aufstellung und Montage sowie sorgfältige Bedienung und Instandhaltung voraus.
Marken
Alle mit dem Schutzrechtsvermerk gekennzeichneten Bezeichnungen sind eingetragene Marken der Siemens AG. Die übrigen Bezeichnungen in dieser Schrift können Marken sein, deren Benutzung durch Dritte für deren Zwecke die Rechte der Inhaber verletzen kann.
Haftungsausschluss
Wir haben den Inhalt der Druckschrift auf Übereinstimmung mit der beschriebenen Hard- und Software geprüft. Dennoch können Abweichungen nicht ausgeschlossen werden, so dass wir für die vollständige Übereinstimmung keine Gewähr übernehmen. Die Angaben in dieser Druckschrift werden regelmäßig überprüft, notwendige Korrekturen sind in den nachfolgenden Auflagen enthalten.
Siemens AG
Automation and Drives
Postfach 48 48
90437 Nürnberg
DEUTSCHLAND
(5)J31069-D0126-U001-A6-7418
Ausgabe 05/07
Copyright E Siemens AG 1999, 2000, 2002, 2003, 2007
Änderungen vorbehalten
A 05/07 Inhaltsverzeichnis
Inhaltsverzeichnis
1 Allgemeines
1.1
1.2
2 Die Inbetriebnahme des STG Hand-Held Terminal PRO . . . . . . . . .
2.1
2.2
2.3
2.4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Einsatzgebiete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Produktbeschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mitgelieferte Komponenten . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Einschalten des Gerätes und Einstellen der Betriebsart . . . .
MOBY-Applikationen
Bedienung
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Die Bedienung des STG Hand-Held Terminal PRO . . . . . . . . . . . . .
3.1
Die Tastatur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.1
Die Umschalttasten
3.1.2
Tastenfunktionen
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
3.3
Die Antenne am Lesekopf und das Antennenfeld
Die Ladefunktion
. . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-11
4 Die Programme “MOBY D/E/I”
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-12
4.1
Der Dateneditor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-14
4.2
Die MDS-Funktionen
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.1
Allgemeines zu Lesen und Beschreiben eines MDS
4.2.2
MDS lesen
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.3
MDS beschreiben
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.4
MDS löschen/Initialisieren
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.5
Lesen der ID-Nummer
4.2.6
Rohdaten lesen
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3
Die Datei-Funktionen
4.3.1
Laden einer Datei
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2
Speichern
4.3.3
Beenden
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4
Die Funktionen Editor
4.4.1
Sprung zur Adresse
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.2
Anzeige
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.3
Anzeige löschen
4.4.4
Datum editieren
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-I
Inhaltsverzeichnis A 05/07
4.5
Die Funktionen Extras
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.1
Kommunikation
4.5.2
Passwort
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.3
Antenne
4.5.4
Adressen Setup
4.5.5
4.5.6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MOBY I Setup
MOBY E Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6
Die Funktionen “?”
4.6.1
Sprache
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6.2
Ueber
4.6.3
Version
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Das Programm “FILEHANDLER”
5.1
Allgemeines zum Filehandler
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-29
. . . . . . . . . . . . . . . . . . . . . . . . . . . D-29
5.2
Die Filehandler-Befehle
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-30
5.3
Die Anzeigen Editor und Directory
5.3.1
Der Dateneditor im Filehandler
5.3.2
Die Directory-Ansicht
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4
Das Datei-Menü
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4.1
Lese Datei vom MDS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4.2
Lese Datei vom STG RAM
5.4.3
Schreibe Datei auf MDS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4.4
Schreibe Datei auf STG RAM
5.4.5
Lese Verzeichnis vom MDS
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4.6
Lese Verzeichnis vom STG RAM
5.4.7
Beispiel: Kopieren von Dateien
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
5.5
Das Befehle-Menü
5.5.1
Datei neu
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5.2
Datei löschen
5.5.3
5.5.4
5.5.5
Datei Attribut
MDS Status
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MDS formatieren
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5.6
MDS Cover
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6
5.6.1
5.6.2
5.6.3
Das Editor-Menü
Anzeige Verzeichnis
Anzeige Editor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Datei Größe verändern
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6.4
Anzeige löschen
5.6.5
Sprung an Adresse
5.6.6
Anzeige Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D-II
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Inhaltsverzeichnis
5.7
Das Extra-Menü
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.7.1
Parameter
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.7.2
Passwort für Filehandler
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.7.3
Kommunikation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8
Die Funktionen “?”
6 Erweiterte Funktionen
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-46
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-47
6.1
Die Hinterlegung der MDS-Daten im Handterminal
6.2
Kopieren von MOBY-Daten von und zum
STG Hand-Held Terminal PRO
6.2.1
Was wird zusätzlich benötigt?
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.2
Installation
6.2.3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Daten Austausch
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.4
Die Organisation der Datei READ.HEX
6.2.5
Die Organisation der Datei READ.HX1
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
6.3
6.4
Funktionen mit dem PSION-Betriebssystem
Die automatische Stromsparfunktion
. . . . . . . . . . . . . . D-53
. . . . . . . . . . . . . . . . . . . . . D-54
6.5
Anschluss von SIM-Geräten (MOBY E/I)
6.5.1
Sicherheit
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6
System-RESET
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-58
7 Fehlermeldungen
7.1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fehlermeldungen bei den Programmen “MOBY D/E/I”
7.2
Fehlermeldungen beim Programm “FILEHANDLER”
8 Technische Daten
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-65
A Anhang
A.1
Bestellung von Komponenten für erweiterte Funktionen
A.2
Portieren von Anwenderapplikationen
. . . . . . . . . . . . . . . . . . . . D-69
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-III
Inhaltsverzeichnis A 05/07
D-IV
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Allgemeines
1 Allgemeines
Das STG Hand-Held Terminal PRO (Service- und Testgerät) erweitert die Identifikationssysteme MOBY D, MOBY E bzw. MOBY I um ein leistungsfähiges mobiles Handterminal (Basis: PSION Workabout PRO) für Applikationen in den
Bereichen Logistik, Distribution und Service. Darüber hinaus ist es ein unentbehrliches Hilfsmittel bei der Inbetriebnahme und beim Test.
STG Hand-Held Terminal PRO mit
MOBY D/E/I Lesekopf
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-1
Allgemeines A 05/07
1.1
Einsatzgebiete
Das STG Hand-Held Terminal PRO ist bei MOBY D, MOBY E und MOBY I einsetzbar. Das enthaltene Service- und Testprogramm gestattet ein einfaches Lesen und Beschreiben aller Datenspeicher von MOBY D, MOBY E oder MOBY I.
Darüberhinaus kann der Kunde sehr einfach seine eigene Applikation auf dem
Handterminal programmieren. Eine C-Library für die Programmierung der
Handterminal-Leseköpfe wird von Siemens angeboten. Damit werden Anwendungen im Bereich Lager, Logistik und Kommissionierung einfach realisierbar.
Der Einsatz des Handterminals kann auch in rauher Umgebung erfolgen. Das
Handterminal ist sehr robust und gegen Spritzwasser geschützt. Das Display ist durch die vorhandene Displaybeleuchtung gut lesbar.
1.2
Produktbeschreibung
Das STG Hand-Held Terminal PRO besteht aus einem Grundgerät und einem
Lesekopf von MOBY D, MOBY E oder MOBY I. Das Grundgerät ist ein PSION
Workabout PRO. Dieses Gerät ist weltweiter Standard bei industriellen Handterminals. Das Service- und Testprogramm startet sich beim Einschalten des
Handterminal automatisch. Mit dem Handterminal können alle Datenspeicher von MOBY D, MOBY E oder MOBY I bearbeitet werden.
D-2
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Allgemeines
Folgende Funktionen können ausgeführt werden:
S Auslesen der Daten aus dem MDS
S Schreiben der Daten in den MDS
S Löschen des gesamten Datenspeichers (Beschreiben mit einem Füllwert)
S Lesen und Anzeigen der ID-Nummer des MDS (MOBY D/E)
S Darstellen und Editieren der Daten in Hexadezimal und ASCII
S Passwortschutz ein- und ausschaltbar für alle schreibenden Funktionen und zum Beenden des MOBY-Programms
S Menüführung in verschiedenen Sprachen (Deutsch und Englisch)
S Abspeichern der gelesenen MOBY-Daten in Dateien. Dafür stehen im Handterminal ca. 40 MB zur Verfügung.
Zusätzliche Funktionen bei MOBY I-Filehandler:
S Formatieren des MDS
S Anlegen von Dateien auf dem MDS
S Beschreiben von Dateien auf dem MDS
S Lesen von Dateien auf dem MDS
S Auslesen und Anzeigen der Directory
S Löschen von Dateien auf dem MDS
Der Schreib-/Lesekopf von MOBY D/E/I wird einfach mit dem PSION-Grundgerät verschraubt. Er besitzt eine serielle TTL-Schnittstelle für die Kommunikation mit dem Grundgerät. Die Spannungsversorgung des Lesekopfes liefert das
Grundgerät.
Der Schreib-/Lesekopf oder die Antenne und das STG-Programm können auch einzeln bestellt werden. Damit ist es möglich, dass der Kunde ein bereits vorhandenes PSION Workabout PRO verwendet.
Das entsprechende Ladegerät (inkl. 110-240-V-Steckernetzteil) für das Wiederaufladen der Akkus muss gesondert bestellt werden.
S MOBY D/E/I
Das Ladegerät (Bestellnummer siehe Katalog) als Docking Station ausgeführt.
Für kundenspezifische RFID-Applikationen steht dem Anwender eine C-Library mit den Funktionen des MOBY-Lesekopfes zur Verfügung. Mit der optionalen
C-Entwicklungsumgebung für den PSION Workabout PRO kann der Anwender
eigene Programme entwickeln (vgl. Anhang A.2).
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-3
Die Inbetriebnahme des STG Hand-Held Terminal PRO A 05/07
2 Die Inbetriebnahme des STG Hand-Held
Terminal PRO
2.1
Mitgelieferte Komponenten
Die Lieferung des STG Hand-Held Terminal PRO besteht aus mehreren Komponenten. Diese sind auch einzeln im Lieferschein vermerkt:
Bestellte
Komponente
MOBY D
STG Hand-
Held Terminal
PRO
MOBY E
STG Hand-
Held Terminal
PRO
MOBY I
STG Hand-
Held Terminal
PRO
Bestellnummer Packliste
6GT2603-0AA10 PSION Workabout PRO 1
MOBY D-Lesekopf
6GT2303-0AA10 PSION Workabout PRO 1
MOBY E-Lesekopf
6GT2003-0CA10 PSION Workabout PRO 1
MOBY I-Lesekopf
Packnummer
6GT2603-1AA00
6GT2303-1AA00
6GT2003-1CA00
1 Die MOBY-Applikation ist auf dem STG Hand-Held Terminal PRO vorinstalliert.
D-4
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Die Inbetriebnahme des STG Hand-Held Terminal PRO
2.2
Einschalten des Gerätes und Einstellen der
Betriebsart
Nach dem ersten Aufladen des Akkus ist das Handterminal sofort betriebsbereit.
Schalten Sie das Gerät ein, in dem Sie ENTER/ON für 4 Sekunden gedrückt halten. Es erscheint ein Auswahlmenü mit den MOBY-Applikationen für den
RF-Schreib-/Lesekopf, den Sie betreiben möchten.
MOBY D Service- und Testprogramm
MOBY E Service- und Testprogramm
MOBY I Service- und Testprogramm
MOBY I Service- und Testprogramm
(Die MDS-Daten sind über den Datei-
namen verfügbar. Siehe Kapitel 5)
Das Gerät schaltet sich automatisch ab, nachdem für 5 Minuten keine Taste gedrückt wurde. Wird das Gerät durch Drücken der ENTER/ON-Taste (für ca. 4 Sekunden) wieder eingeschaltet, arbeitet das Handterminal mit der gleichen Maske weiter, in der es sich befand, bevor es manuell oder automatisch
abgeschaltet wurde (siehe Kap. 6.4).
Per Bedienung wird das Gerät durch aufeinanderfolgendes Drücken der Tasten
FN und ENTER/ON ausgeschaltet.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-5
Die Inbetriebnahme des STG Hand-Held Terminal PRO A 05/07
2.3
MOBY-Applikationen
Sollten Sie zu einem späteren Zeitpunkt einen anderen Lesekopf (MOBY D/E/I) am Handterminal betreiben, so müssen Sie zuerst die MOBY-Applikation umstellen. Hierzu müssen Sie die laufende Applikation über das Menü “Datei/Beenden” beenden. Es erscheint der PSION Arbeitsplatz, auf dem dann die benötigte MOBY-Applikation ausgewählt werden muss.
2.4
Bedienung
Die Bedienung der STG-Programme MOBY D/E/I ist im Kapitel 4 beschrieben.
Die Bedienung des Programmes Filehandler für MOBY I ist im Kapitel 5 be-
schrieben.
Über die gelbe Menü-Taste sind alle Funktionen der MOBY-Programme aufrufbar.
D-6
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Die Bedienung des STG Hand-Held Terminal PRO
3 Die Bedienung des STG Hand-Held Terminal PRO
3.1
Die Tastatur
Die Tastatur des PSION Workabout PRO ist in 3 Teile gegliedert:
S Steuertasten direkt unterhalb des Displays
S numerischer Ziffernblock
S ASCII-Tastatur
Steuertasten:
Ein-/Aus;
Cursortasten,
CTRL-Taste
Die grüne
Leuchtdiode blinkt grün, wenn der Akku geladen wird und leuchtet dauerhaft, wenn der
Ladevorgang abgeschlossen ist.
Numerischer
Ziffernblock
ASCII-
Tastatur
Gelbe Tasten: Öffnen des Menüs der MOBY-Applikation
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-7
Die Bedienung des STG Hand-Held Terminal PRO A 05/07
3.1.1
Die Umschalttasten
<SHIFT>
<CTRL>
<ALT>
<ORANGE>
<BLUE>
Aktivieren der Umschalttasten
Durch Drücken/Aktivieren einer Umschalttaste erscheint in der Taskleiste in
Kleinbuchstaben die Benennung der gewählten Umschalttaste, z. B. “org key”,
“blue key”. Eine nachfolgend aktivierte Taste ändert daraufhin ihre Funktion, die
Anzeige in der Taskleiste erlischt und die Umschalttaste ist wieder deaktiviert.
3.1.2
Tastenfunktionen
<SHIFT>
Taste Funktion
Anzeige von Großbuchstaben (A-Z) und Symbolen, die auf den Zifferntasten mit angegeben sind
(z. B. &, *,...).
Ermöglichen die Navigation im Display nach links, rechts, oben und unten.
Pfeiltasten
(graue runde Taste unterhalb des Displays)
<BKSP>
<DEL>
(blaue Taste und BKSP>
<CTRL>
<ALT>
<TAB>
<ESC>
<SPACE>
Bewegt den Cursor nach links zum Löschen des zuletzt eingegebenen Zeichens.
Entfernt das Zeichen, das nach dem Cursor steht.
d T
Bewegt den Cursor in bestimmten Abständen nach rechts oder unten.
(<ORANGE> und <TAB> bewegt den Cursor zurück.)
Schließen des momentan geöffneten Menüs, Dialogfensters oder einer gerade gestarteten Anwendung und Rückkehr zur vorherigen Oberfläche.
Einfügen von Leerzeichen.
In einem Windows-Dialogfenster können mit der
<SPACE>-Taste Kontrollkästchen aktiviert oder deaktiviert werden.
D-8
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Die Bedienung des STG Hand-Held Terminal PRO
3.2
Die Antenne am Lesekopf und das Antennenfeld
Die Antenne des Lesekopfes ist an der oberen Seite des Handterminals angeordnet.
Mit unterschiedlichen MDS-Typen werden unterschiedliche Reichweiten erzielt.
Die folgende Tabelle gibt einen Überblick:
MOBY D
MDS-Typ
D139
D160
D124
Labels auf Basis
I-Code: 3
30
MOBY E mm MDS-Typ
60 E600 (ISO-Card)
25 E611
E624 (Knopf)
E623 (Pille) 1
I-Code1
I-Code SLI
Tag-it HF-I my-d
75
100
100
100 mm MDS-Typ
18 402/401
30 404/514/413E
8
4/3 2
403
506
439E
MOBY I mm
6
20
8
12
12
507 (mit Batterie) 35
507 (ohne Batterie) 4
1 Die Pille kann nur an dem hierfür vorgesehenen Kopfteil gelesen werden.
2 wenn MDS in Metall eingebaut ist
3 Fertigungsbedingt ist mit Reichweitentoleranzen zu rechnen. Die Reichweiten gelten für Labels der Größe 85 x 55 mm.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-9
Die Bedienung des STG Hand-Held Terminal PRO A 05/07 z. B.:
MDS E600
MOBY D/E
Flächenantenne
MOBY E/I
Knopfantenne bzw.
Stabantenne (MOBY I) z. B.:
MDS E623
Das Antennenfeld beim STG-Lesekopf
Das Antennenfeld bei MOBY E
Beim MOBY E-Lesekopf sind 2 Antennen im Leser integriert. Je nachdem, welchen MDS Sie lesen möchten, müssen Sie diesen entsprechend am Lesekopf positionieren. Die Umschaltung des Antennenfeldes geschieht mit dem Befehl
Extras/ANTENNE (siehe Kap. 4.5.3). Wichtig ist dabei, dass der MDS E623 nur
an der hierfür vorgesehenen Antenne (siehe Bild) gelesen werden kann. Der
MDS E624 kann sowohl an der Knopfantenne als auch an der Flächenantenne gelesen werden.
D-10
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Die Bedienung des STG Hand-Held Terminal PRO
3.3
Die Ladefunktion
Sobald Sie das PSION Workabout PRO in die Docking Station stecken, wird der Ladevorgang der Akkus gestartet. Das Laden wird aktiviert und an einer
grünen Leuchtdiode angezeigt (siehe Kap. 3.1).
Bei leeren Akkus dauert eine komplette Ladung ca. 4 Stunden.
WICHTIG: Dem Gerät liegt eine Dokumentation “Quick Start Guide” bei. Die darin enthaltenen Hinweise sind unbedingt zu beachten. Ebenso die entsprechenden Hinweise im PSION-Benutzerhandbuch bzw. der Dokumentation der
Docking Station.
Die Backup-Batterie
Die Backup-Batterie im PSION Workabout PRO dient zum Erhalt der Anwendungsdaten, wenn die Hauptbatterien entladen sind. Die Backup-Batterie ist eine Lithiumzelle. Bitte beachten Sie, dass eine neue Backup-Batterie (bei entleerter oder entfernter Hauptbatterie) die Daten im RAM nur wenige Minuten erhalten kann.
Die MOBY-Applikation ist ausfallsicher im Flash Speicher hinterlegt und ist daher auch nach einem Batterieausfall vorhanden. Falls die MOBY-Applikation gelöscht oder beschädigt wurde, muss das Gerät zur Reparatur eingesandt werden.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-11
Die Programme “MOBY D/E/I” A 05/07
4 Die Programme “MOBY D/E/I”
Nach dem Einschalten des STG Hand-Held Terminal PRO erscheint am Display der Editor. Sie können nun die Daten anschauen, neue Daten eingeben oder über die gelbe Menü-Taste eine Funktion aufrufen. Ein direkter Aufruf der
Funktionen ist über die Taste ebenfalls möglich. Drücken Sie hierzu nacheinander die Taste ALT und danach die entsprechende alphanumerische Taste. Die folgende Tabelle zeigt alle Funktionen und die dazugehörigen Kurzaufrufe:
Befehl
Datei/Laden Datei
Datei/Speichern
Datei/Beenden
MDS/Lesen
Kurzaufruf
D
C
X
L
1 Beschreibung
Datei vom PSION RAM-Laufwerk in den
Arbeitsspeicher laden
Gelesene MDS-Daten auf das
RAM-Laufwerk speichern
STG-Anwendung beenden
Daten vom MDS lesen
MDS/Schreiben
MDS/Loeschen/Init
S
E
MDS/Lese TagId T ID-Nummer des MDS lesen
MDS/Roh-Daten lesen R Physikalischen Speicher des MDS auslesen
Editor/Sprung zur Adresse J bzw. Tab Im Editor zu einer bestimmten Adresse springen
Editor/Anzeige O Optionen der Anzeige ändern
Editor/Anzeige loeschen F
Daten auf MDS schreiben
MDS mit bestimmten Wert beschreiben
Editor/Datum editieren
Extras/Kommunikation
Extras/Passwort für STG
Extras/Adressen Setup
Extras/MOBY I Setup
Extras/MOBY E Setup
A
K
P
G
B
Y
Daten im Editor auf bestimmten Wert löschen
Das Datum an der Cursorposition in verschiedenen Formaten bearbeiten
Optionen in der Kommunikation ändern
Passwort für die STG-Anwendung
ändern
Eingaben für die Befehle “MDS lesen/ schreiben” definieren
Speichergröße und MOBY I-Betriebsarten einstellen
Umschaltung des MDS-Zugriffs vom “MOBY-Schlüssel” (A) auf den
B-Schlüssel
Feldbetriebsart bei MOBY E SIM: Umschaltung zwischen zyklischem Betrieb und Dauerbetrieb
D-12
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Die Programme “MOBY D/E/I”
?/Sprache
?/Ueber
?/Version
Befehl Kurzaufruf
H
U
V
1 Beschreibung
Menüsprache einstellen
Herstellerdaten
Version von Betriebssystem und
STG-Anwendung
1 Deutsche Kurzaufrufe (Shortcuts); für die englische Menüsprache verwenden Sie die englische
Bedienungsanleitung.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-13
Die Programme “MOBY D/E/I” A 05/07
4.1
Der Dateneditor
Das Editieren der MDS-Daten kann im Editorfenster in Hexadezimal oder in
ASCII erfolgen. Die Umschaltung erfolgt im Menü EDITOR/ANZEIGE.
Im Editor ist immer die gesamte Größe eines MDS-Speichers abgebildet. Sie können mit den Cursorfunktionen zu den einzelnen Adressen gelangen. Ein
Sprung zu einer beliebigen Adresse kann mit der “Tab”-Taste durchgeführt
Anzeige des aktuell eingestellten Lese-
Die TagId des MDS wird nur bei
MOBY D/E angezeigt. Sie ist gültig nach dem Ausführen der Funktion
“MDS/Lesen-Schreiben-LeseTagId”
Datumfeld:
Das Datum, an dem sich der Cursor befindet, wird alternativ in den Formaten
Hex, Dec, ASCII oder Bin dargestellt.
Mit der Funktion “Editor/Datum editieren” kann der Wert im Datumfeld verändert werden.
Das Editor-Fenster beinhaltet die MDS-
Daten. Standardmäßig werden 32 Byte dargestellt.
MDS-Adressen werden hexadezimal oder dezimal dargestellt.
D-14
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Die Programme “MOBY D/E/I”
Der “Aktuelle Bereich”
Der “Aktuelle Bereich” wird im Editor in normaler Darstellung angezeigt. Alle anderen Datenbereiche des MDS werden invertiert dargestellt. Der Aktuelle Bereich zeigt den zuletzt gelesenen Datenblock an. Beim Lesen/Schreiben wird der Aktuelle Bereich als Wert für den
Schreibbefehl eingetragen.
Dieser Wert kann jedoch im Menü
MDS/SCHREIBEN bzw. MDS/LESEN angepasst werden.
Aktueller Bereich
Eine Veränderung des Aktuellen Bereiches geschieht automatisch, wenn Sie
Daten editieren und überschreiben.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-15
Die Programme “MOBY D/E/I” A 05/07
Die Größe des am Display dargestellten Speicherbereichs kann über die
Funktion EDITOR/ANZEIGE umgeschaltet werden: (siehe Kap. 4.4.2)
In der Normaldarstellung werden
32 Byte in kleinen Buchstaben dargestellt. Sie erhalten einen Überblick über die MDS-Daten.
In der Zoomdarstellung werden nur
4 aufeinanderfolgende Byte angezeigt.
Die Darstellung ist in großen Buchstaben. Das Ablesen vom Display ist ohne
Anstrengung möglich.
Zoomdarstellung hexadezimal
Zoomdarstellung ASCII
D-16
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Die Programme “MOBY D/E/I”
4.2
Die MDS-Funktionen
Die MDS-Funktionen führen eine Kommunikation mit dem MDS durch.
Die MDS-Funktion wird nicht unterbrochen, wenn Sie kurzzeitig den MDS aus dem Lesefeld bewegen. Wird der
MDS länger als 30 Sekunden nicht bearbeitet, so wird die Funktion unterbro-
Nach dem Start eines Befehls wird auf dem Display ein Fenster mit einem Balken dargestellt. Dieser zeigt an, wieviel
Prozent des Befehls bereits abgearbeitet sind.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-17
Die Programme “MOBY D/E/I” A 05/07
4.2.1
Allgemeines zu Lesen und Beschreiben eines MDS
Die MDS von MOBY D und MOBY E haben einen blockorientierten Datenzugriff. Ein Lesen oder Beschreiben eines MDS ist nur von einem Blockanfang möglich.
Ein Block hat bei MOBY E jeweils eine Länge von 16 Byte (bzw. 10 Hex). Die beim STG Hand-Held Terminal PRO einzugebenden Anfangsadressen für die
MDS-Bearbeitung sind demnach: 00, 10, 20, 30 hex usw.
Ein Block hat bei MOBY D jeweils eine Länge von 4 Byte (I-Code, Tag-it) oder
8 Byte (my-d). Die Anfangsadressen sind demnach:
00, 04, 08, 12 hex ... (I-Code, Tag-it) oder
00, 08, 10, 18 hex ... (my-d).
Bei MOBY D/E wird nach dem Lesen/Schreiben die TagId im Display automatisch auf den aktuellen Wert gebracht.
Es ist jedoch möglich, jede beliebige Anfangsadresse anzugeben. Diese wird vom
STG Hand-Held Terminal PRO akzeptiert und auf den nächstniedrigeren Blockanfang korrigiert. Die Adresskorrektur wird dem Bediener in einem Fenster angezeigt und muss quittiert werden.
Ein weiteres Fenster erscheint, wenn Sie im
Editor Daten geändert haben und anschlie-
ßend versuchen, einen MDS zu lesen. Hier macht Sie ein Hinweis darauf aufmerksam, dass die soeben geänderten Daten mit dem
MDS-Lesebefehl möglicherweise wieder überschrieben werden. Sie haben die Möglichkeit, die geänderten Daten im Editor zu behalten, zu verwerfen oder den Befehl komplett abzubrechen.
Hinweis
Am Handterminal kann nur bei MOBY I der ECC-Mode eingestellt werden.
Bei MOBY D/E ist die ECC-Betriebsart nicht möglich.
D-18
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Die Programme “MOBY D/E/I”
4.2.2
MDS lesen
Es kann ein Datenblock mit einer frei definierbaren Anfangs- und Endadresse vom MDS gelesen werden. Wird für Anfangs- und Endadresse der gleiche Wert eingegeben, so kann vom MDS nur ein Block gelesen werden. Der Adressbereich wird in einem weiteren Fenster zur Bestätigung angezeigt.
Hinweis
Wurde im Menü “Extras/Adressen Setup/........” im Feld Lesen/
Schreiben der Modus “MDS komplett” gewählt, so wird die Funktion
“MDS/Lesen” ohne weitere Nachfrage sofort gestartet. Es wird immer der gesamte MDS bearbeitet.
4.2.3
MDS beschreiben
Es kann ein Datenblock auf den MDS geschrieben werden. Der im Editor gültige Datenblock wird dabei als Default bei jedem Schreibvorgang angezeigt.
Die Defaultlänge bzw. Endadresse kann beim Beschreiben noch auf einen anderen Wert geändert werden.
4.2.4
MDS löschen/Initialisieren
Die Funktion “MDS löschen/Init” dient dazu, sehr schnell den kompletten MDS mit einem bestimmten Wert zu beschreiben. Der Löschwert kann in einem
Folgemenü eingegeben werden. Nach der Löschfunktion ist der Speicher im
Editor ebenfalls auf den eingegebenen Wert gelöscht. Bei MOBY I muss vor dieser Funktion die richtige MDS-Speichergröße eingestellt sein (Extras/
MOBY I Setup).
4.2.5
Lesen der ID-Nummer
Nur MOBY D/E: Die Funktion liest die Seriennummer vom MDS und zeigt sie an. Die ID-Nummer wird vom Werk eingestellt und kann nicht verändert werden.
Die Anzeige der TagId erfolgt im Editor in der zweiten Zeile in hexadezimaler
Form.
Das Lesen der TagId wird bei den Funktionen MDS lesen/schreiben/löschen automatisch durchgeführt.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-19
Die Programme “MOBY D/E/I” A 05/07
4.2.6
Rohdaten lesen
Nur MOBY D/E: Mit dieser Funktion wird der komplette Speicher des MDS physikalisch ausgelesen. Insbesondere werden TagId, Schlüsselinformationen (soweit Public), Herstellerinformation und MDS-Zugriffsrechte dargestellt. Für die
Interpretation der Daten ist die Kenntnis des physikalischen Speicheraufbaus des MDS notwendig (siehe Beschreibung MFWAPI bzw. CCTWAPI).
Mit der Funktion “Rohdaten lesen” können Fehler erkannt werden, die bei der
Konfigurierung des MDS entstanden sind.
D-20
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07
4.3
Die Datei-Funktionen
Die Programme “MOBY D/E/I”
4.3.1
Laden einer Datei
Es kann eine Datei in den STG Hand-Held Terminal PRO-Editor geladen werden, die
S vorher mit dem Befehl “Datei/Speichern” abgespeichert wurde oder
S vom PC in das Verzeichnis /SIBO/M des PSION Workabout PRO übertra-
4.3.2
Speichern
Die Daten, die gerade im Editor angezeigt werden, können in einem File auf dem PSION Workabout PRO abgespeichert werden. Der Filename kann dabei aus 1 bis 8 Buchstaben oder Ziffern bestehen. Beim Abspeichern wird dem Filenamen automatisch die Endung “.HEX” (Daten) und “.HX1” (ID-Nr.) hinzuge-
Für das Abspeichern von MDS-Daten steht im Handterminal ein Speicherbereich von ca. 40 MB zur Verfügung. Bei MOBY E können demnach bis zu
40.000 MDS gelesen und gespeichert werden.
4.3.3
Beenden
Mit der Funktion “Beenden” können Sie das STG Hand-Held Terminal PRO-
Programm von MOBY beenden. Sie gelangen auf die Betriebssystemebene
des PSION Workabout PRO (siehe Kap. 6.3).
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-21
Die Programme “MOBY D/E/I”
4.4
Die Funktionen Editor
A 05/07
4.4.1
Sprung zur Adresse
Sie können in dezimaler oder hexadezimaler Form eine Speicheradresse eingeben. Die Einstellung kann unter Menüpunkt Display/Display Address verändert werden. Anschließend wird im Editor diese Adresse als Anfangsadresse dargestellt.
Diese Funktion kann auch direkt im Editor mit der “Tab”-Taste ausgelöst werden.
4.4.2
Anzeige
In diesem Menü erfolgen die Einstellungen
S Editor umschalten zwischen 32 Byte-Darstellung (4x8= kleine Anzeige) und
4 Byte-Darstellung (1x4= große, gut lesbare Zeichen)
S In der Editor-Darstellung 1x5 wird keine Adresse angezeigt. Es werden die ersten 5 Byte der gelesenen Daten angezeigt. Ein Positionieren mit dem
Cursor auf andere Adressen ist nicht möglich.
S Editor umschalten zwischen “Hexadezimal”- und “ASCII”-Darstellung. Die
Adressen werden immer in hexadezimaler oder dezimaler Form dargestellt.
S Datum umschalten zwischen “BIN”-, “ASCII”-, “DEZ”- und “HEX”-Darstellung
D-22
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Die Programme “MOBY D/E/I”
4.4.3
Anzeige löschen
Die Funktion “Anzeige löschen” beschreibt den kompletten Speicher im
STG Hand-Held Terminal PRO-Editor mit einem Wert, den Sie vorgeben können. Anschließend können Sie im Editor die gewünschten Daten auf die entsprechenden Werte abändern. Eine Funktion zum MDS erfolgt dabei nicht.
S Die Anzeige im Datumfeld kann in den Formaten Hexadezimal, ASCII, Dezimal oder Binär erfolgen. Mit dem hier eingestellten Format können die Daten mit der Funktion “Anzeige/Datum editieren” auch verändert werden.
S Die Anzeige der Adressen kann zwischen Hexadezimal und Dezimal umgeschaltet werden.
4.4.4
Datum editieren
Die Funktion “Datum editieren” stellt neben den Standardformaten Hex und
ASCII des Editorfensters auch die Formate Dezimal und Binär zur Dateneingabe zur Verfügung.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-23
Die Programme “MOBY D/E/I”
4.5
Die Funktionen Extras
A 05/07
4.5.1
Kommunikation
S Schnittstelle: Hier erfolgt die Umschaltung zwischen TTL-Schnittstelle
(Lesekopf) und RS 232-Schnittstelle.
Bei RS 232-Einstellung muss das “Protokoll” auf den
Eintrag “MOBY E/SIM” oder “ASM 420/I/V” eingestellt werden.
S Protokoll: Abhängig vom jeweiligen Lesekopf können hier bestimmte
Protokolle eingestellt werden:
Lesekopf einstellbare Protokolle
MOBY D
MOBY E
MOBY I
MOBY D
MOBY D ISO
MOBY E
MOBY E/SIM
MOBY I
ASM 420/I/V
Durch die Einstellung des MOBY-Protokolls wird bei MOBY E auch automatisch die Speichergröße des Editors festgelegt.
Bei MOBY I wird die Speichergröße des Editors mit der
Funktion “Extras/MOBY I Setup” eingestellt.
D-24
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Die Programme “MOBY D/E/I”
4.5.2
Passwort
Optional können Sie ein Passwort programmieren. Das Passwort muss vor einer Schreibfunktion eingegeben werden. Ein eingegebenes Passwort bleibt bis zum Abschalten des STG Hand-Held Terminal PRO gültig. D. h., bei mehreren aufeinanderfolgenden Schreibbefehlen muss das Passwort nur einmal eingegeben werden. Ein Verlassen des “MOBY”-Programmes ist ebenfalls nur mit
Passwort möglich.
Passwort vergessen?
Wurde ein Passwort vergessen, so gibt es keine Möglichkeit, das Passwort zurückzuerhalten.
Die einzige Möglichkeit besteht darin, das Gerät in den Auslieferungszustand zurückzusetzen. Dazu muss im Startmenü über den Eintrag “Security” der
Supervisor Mode eingeschaltet werden (siehe Kapitel 6.5.1). Danach kann
ebenfalls über das Startmenü das Zurücksetzen des Gerätes über den Eintrag
“Cold Reset” erfolgen.
Das Passwort 99999999
Die Veränderung des Passworts auf den Wert 99999999 (8x die 9) hat eine besondere Bedeutung:
Die Schreibfunktion auf den MDS sowie die Funktion “Datei/Beenden” ist generell nicht mehr möglich. Auch das Passwort kann jetzt nicht mehr geändert werden. Die einzige Möglichkeit, jetzt wieder die Schreibfunktion zu erlangen, ist
der System-RESET (siehe Kapitel 6.5.1).
4.5.3
Antenne
Nur bei MOBY E: Das Antennenfeld am Lesekopf wird umgeschaltet zwischen
“Karte” (große Antenne) und “Pille” (kleine Antenne) (siehe auch Kap. 3.2).
Die
Antenne muss einmalig bei der Inbetriebnahme des Lesekopfes eingestellt werden. Beim Ausschalten des Handterminals bleibt die eingestellte
Antenne im Lesekopf gespeichert.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-25
Die Programme “MOBY D/E/I” A 05/07
4.5.4
Adressen Setup
Mit dieser Funktion wird der Aufruf der Befehle “MDS lesen/schreiben” definiert.
S Start-Adresse + Laenge: Die Eingabe der MDS-Adresse beim
Befehl Lesen/Schreiben erfolgt über eine Startadresse und die Länge der zu bearbeitenden Daten.
End-Adresse: Die Eingabe der MDS-Adresse beim
Befehl Lesen/Schreiben erfolgt über
Startadresse und Endadresse.
S Lesen/Schreiben: Umschaltung von “Block” auf “MDS komplett”. Diese
Einstellung betrifft die Defaulteinstellung bei der Ausführung eines MDS-Befehls.
Block: Beim Lesen/Schreiben eines MDS wird immer der gerade aktive Bereich als der zu lesende-/schreibende Bereich angezeigt.
MDS komplett: Beim Lesen/Schreiben eines MDS wird immer der gesamte MDS bearbeitet.
Die Lese-/Schreibfunktion wird sofort gestartet. Die Eingabe eines Teilbereiches des MDS ist nicht möglich.
D-26
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Die Programme “MOBY D/E/I”
4.5.5
MOBY I Setup
S Speicher Groesse: Speichergröße des zu bearbeitenden MDS festlegen.
Mit dieser Einstellung wird auch der Speicherbereich im
Editor festgelegt. Es ist nicht möglich, MDS-Speicheradressen anzusprechen, die über die Speichergröße hinausgehen.
S MDS Typ: Es wird zwischen RAM/FRAM und EEPROM unterschieden. In der Einstellung RAM/FRAM wird eine leere
MDS-Stützbatterie am STG Hand-Held Terminal PRO angezeigt.
S ECC:
S
S
MDS507:
Abtastzeit:
Ein-/Ausschalten des ECC-Treibers
Der Anwendungszweck des ECC-Treibers ist in der
MOBY-Anschaltungsdokumentation beschrieben.
Dieser Parameter ist nur beim Betrieb des MDS 507 auf
“ja” einzustellen. Beim MDS507-Betrieb wird die Dialogbatterie abgefragt und als Status angezeigt, wenn diese leer wird.
Die Abtastzeit ist nur beim Betrieb des MDS 507 über ein ASM 420 von Bedeutung. Der Einstellbereich liegt zwischen 0,1 s und 6,3 s. Der Defaultwert (0,5 s) muss in der Regel nicht verändert werden.
4.5.6
MOBY E Setup
S Schlüssel A/B: Es kann zwischen dem “MOBY-Schlüssel” und dem
“B-Transportschlüssel für MIFARE-Datenspeicher” umgeschaltet werden. Standardmäßig wird immer mit dem MOBY-Schlüssel gearbeitet. Die Einstellung “B” gestattet das Bearbeiten vom MIFARE-MDS im Auslieferungszustand (Der B-Schlüssel muss sich im Urzustand befinden).
S Feldbetriebsart:
Nur bei MOBY E SIM (vgl. Kap. 6.5): Umschaltung des
SIM vom zyklischen Betrieb in den Dauerbetrieb.
Im Dauerbetrieb erfolgt die Befehlsbearbeitung deutlich
schneller.
S Antenne: Es kann zwischen Karte und Pille umgeschaltet werden.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-27
Die Programme “MOBY D/E/I”
4.6
Die Funktionen “?”
A 05/07
4.6.1
Sprache
Beim STG Hand-Held Terminal PRO kann als Menüsprache Deutsch oder Englisch ausgewählt werden. Die Default-Sprache bei der Inbetriebnahme des
STG Hand-Held Terminal PRO ist Englisch.
4.6.2
Ueber
Angaben zum Hersteller des STG-Programmes: Siemens AG A&D SC FS
4.6.3
Version
Gibt die Version des STG-Programmes, des emulierten Betriebssystems
EPOC, den Ausgabestand der emulierten ROM-Version sowie den Ausgabestand der MOBY-Library aus. Bei Fehlerrückmeldungen an Siemens sind diese
Parameter unbedingt anzugeben.
D-28
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Das Programm “FILEHANDLER”
5 Das Programm “FILEHANDLER”
5.1
Allgemeines zum Filehandler
Wie bei einem PC-basierenden System erfolgt beim Filehandler der Datenzugriff über logische Dateinamen und nicht über physikalische Speicheradressen.
Das folgende Bild zeigt den Aufbau und die Arbeitsweise des Programmes
“FILEHANDLER”:
Dateien im
Handterminal
File 3.hex
File 2.hex
File 1.hex
Directory-
Anzeige
Dateien im MDS
File 3
File 2
File 1 optionale Verbindung zum PC
WORD
EXCEL
.
.
Editor-
Anzeige
MOBY\File 3.hex
MOBY\File 2.hex
MOBY\File 1.hex
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-29
Das Programm “FILEHANDLER” A 05/07
Das Programm “FILEHANDLER” ist so aufgebaut, dass Sie mit den gleichen
Funktionen auf die Handterminal-Dateien und auf die MDS-Dateien zugreifen können. Die Directory-Anzeige ist für das Handterminal und den MDS verfügbar. Dateien vom MDS können mit nur wenigen Tasten vom MDS zum Handterminal kopiert werden (und umgekehrt).
Über eine optionale Verbindung zum PC können die im Handterminal gespeicherten Dateien mit dem PC ausgetauscht werden.
Nun können Sie die Daten mit Ihnen bekannten PC-Programmen weiter bearbeiten (z. B.: WORD, EXCEL, ...). Voraussetzung ist, dass der Inhalt und die
Datenstruktur des MDS-Files von der PC-Applikation unterstützt werden (siehe
Hinweis
Bitte beachten Sie, dass der Filehandler nur für MOBY I zur Verfügung steht.
5.2
Die Filehandler-Befehle
STG-Befehl
Datei/Lese Datei vom
MDS
Datei/Lese Datei vom
STG RAM
Datei/Schreibe Datei auf MDS
Datei/Schreibe Datei auf STG RAM
Datei/Lese Verz. vom
MDS
Datei/Lese Verz. vom
STG RAM
Datei/Beenden
Befehle/Datei neu
Befehle/Datei loeschen
Befehle/MDS Format I
Kurzaufruf 1 Filehandler-
Befehl
R bzw.
Enter
READ
S –
Beschreibung
Eine Datei vom MDS lesen
W
T
G
P
X
B
D bzw. Del 2
WRITE
–
DIR
–
–
CREATE
DELETE
FORMAT
Eine Datei vom RAM des
Handterminals lesen
Eine Datei auf den MDS schreiben
Die Daten vom Editor auf das Handterminal schreiben
Directory vom MDS einlesen und anzeigen
Directory des STG (RAM-
Speicher) anzeigen
Filehandler-Anwendung beenden
Neue Datei mit Länge 0 auf dem MDS anlegen
Datei auf dem MDS löschen
Den MDS formatieren
D-30
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Das Programm “FILEHANDLER”
STG-Befehl
Befehle/Datei Attribut
Befehle/MDS Status
Befehle/MDS Cover
Kurzaufruf
Y
F
C
1
Editor/Anzeige Verzeichnis
Q
Editor/Anzeige Editor U
Editor/Datei Groesse N –
Editor/Anzeige loeschen
Editor/Sprung an
Adresse
J
O bzw. Tab
Editor/Anzeige Setup H
–
–
–
Filehandler-
Befehl
ATTRIB
Beschreibung
Datei auf dem MDS mit Zugriffsrechten versehen
MDS STATUS MDS Status auslesen
COVER
–
–
Datenstruktur des MDS schützen letzte gelesene Directory anzeigen
Filedaten anzeigen
Filegröße in Editor ändern
Anzeige mit bestimmtem
Wert beschreiben
Cursor auf Adressposition bringen
Anzeige zwischen ASCIIund HEX-Darstellung umschalten
Extras/Parameter
Extras/Passwort fuer
FH
Z
A
Extras/Kommunikation E
?/Sprache
?/Ueber
?/Version
L
K
V
–
–
–
–
–
–
Filehandler-Parameter einstellen
Passworteinstellung für das
Programm “FILEHANDLER”
Einstellung: Lesekopf oder
ASM
Menüsprache einstellen
Herstellerdaten
Version von Betriebssystem und Filehandler
1 Der Kurzaufruf der Befehle erfolgt über die Tastenkombination ALT+Taste. Hierzu müssen beide Tasten nacheinander gedrückt werden. Die Tasten für die Kurzaufrufe von MDS-Befehlen sind identisch mit den
Buchstaben, wie sie auch über den FC in der SIMATIC angesprochen werden.
2 In der Directory-Ansicht kann mit der “Del”-Taste das gerade ausgewählte File gelöscht werden. Damit können auch Dateien vom RAM des Handterminals gelöscht werden.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-31
Das Programm “FILEHANDLER” A 05/07
5.3
Die Anzeigen Editor und Directory
Die Bildschirmanzeige beim Filehandler befindet sich entweder in der “Directory-Anzeige” oder in der “Editor-Anzeige”. Über das Menü “Editor/Anzeige Editor” und “Editor/Anzeige Directory” kann zwischen den beiden Anzeigen umgeschaltet werden.
5.3.1
Der Dateneditor im Filehandler
Der Dateneditor beim Filehandler ist ähnlich aufgebaut wie beim Standard-
STG-Programm (siehe Kap. 4.1).
Eingestellte MDS-Speichergröße.
Sie kann über den Befehl Extras/Parameter eingestellt werden.
Name des Files im Editor. Die Datei kann sowohl vom MDS als auch vom Handterminalspeicher gelesen worden sein.
Hier wird die Filelänge angezeigt.
Das Datum, an dem sich der Cursor befindet, wird alternativ im ASCII-Format dargestellt.
Wird die Dateigröße verlängert (siehe
Kap. 5.6.3), so werden die verlängerten
Daten invertiert dargestellt.
Der Datenbereich, der größer ist als die
Filelänge, wird mit dem Datenstring
“eof” (end-of-file) gekennzeichnet.
D-32
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Das Programm “FILEHANDLER”
5.3.2
Die Directory-Ansicht
In der Directory-Ansicht werden entweder alle Dateien vom MDS oder vom
RAM des STG Hand-Held Terminal PRO angezeigt. Mit Hilfe der Directory-Ansicht können sehr effektiv Dateien vom MDS gelesen bzw. zwischen Handter-
minal und MDS kopiert werden (siehe Kap. 5.4).
Aufbau der Directory-Anzeige
Hier wird angezeigt, ob das angezeigte
Directory von einem “MDS” oder vom
“Handterminal” stammt.
Name, mit dem der MDS formatiert wurde.
Beim Handterminal-Directory wird kein
Name angezeigt.
Freier Speicher auf dem MDS. Beim
Handterminal sind das ca. 40 MB nach der
Inbetriebnahme.
Mit den Cursortasten kann eine Datei ausgewählt werden. Nach der Auswahl kann direkt eine Funktion mit dieser Datei
ausgeführt werden (siehe Kap. 5.4).
Bei den MDS-Dateien kann hier ein Attri-
but eingetragen sein (siehe Kap. 5.5.4).
Bei Handterminal-Dateien können keine
Attribute gesetzt werden.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-33
Das Programm “FILEHANDLER” A 05/07
5.4
Das Datei-Menü
Im Datei-Menü können im Wesentlichen drei Funktionen aufgerufen werden:
S Datei lesen
S Datei schreiben
S Directory lesen und anzeigen
Diese Funktionen können sowohl auf dem MDS als auch auf dem internen
Speicher des Handterminals ausgeführt werden.
D-34
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Das Programm “FILEHANDLER”
5.4.1
Lese Datei vom MDS
Nach dem Aufruf dieser Funktion erscheint ein Auswahlmenü, in dem Sie mit den Cursortasten eine Datei auswählen können. Es werden dabei alle Filena-
men durchgeblättert, die auch in der Directory-Ansicht (siehe Kap. 5.3.2) zu se-
hen sind.
Nachdem Sie alle Dateien durchgeblättert haben, erscheint der Dateiname “Neues
MDS DIR”. Drücken Sie jetzt die Enter-
Taste, so liest der Filehandler eine
Directory von einem MDS ein.
Anschließend kann eine der neuen
Dateien selektiert werden.
Blättern Sie in dem Dateiauswahlmenü weiter, bis der Dateiname “Andere Datei” erscheint, so können Sie im folgenden
Menü einen Dateinamen über die ASCII-
Tastatur des Handterminals eingeben.
5.4.2
Lese Datei vom STG RAM
Nach dem Aufruf dieser Funktion erscheint ein Auswahlmenü, in dem Sie mit den Cursortasten eine Datei auswählen können. Es werden alle Dateinamen mit der Dateiendung .HEX angezeigt, die sich im RAM des Handterminals befinden. Befindet sich keine Datei mit der Endung .HEX im STG RAM, so erhalten Sie die Meldung “keine Datei vorhanden”.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-35
Das Programm “FILEHANDLER” A 05/07
5.4.3
Schreibe Datei auf MDS
Die Eingabe des Dateinamens erfolgt nach der gleichen Art und Weise, wie im
Kap. 5.4.1 beschrieben. Nach der Eingabe eines in dem Directory vorhandenen
Dateinamens, erhalten Sie eine Auswahl:
Sie können die Datei überschreiben oder die neuen Daten an die bestehende Datei anhängen.
Beim Folgefenster können Sie die Länge der zu schreibenden Daten noch verändern.
Als Defaultlänge wird immer der Wert angezeigt, der auch die Länge der Daten im
Editor darstellt. Verändern Sie die Default-
Längenangabe, so wird auch die Dateilänge auf dem MDS angepasst.
Haben Sie Daten “Anhaengen” ausgewählt, so wird nach der Ausführung der
Schreibfunktion automatisch die Datei nochmal gelesen. Damit erhalten Sie die gesamte aktualisierte Datei in den Editor.
Haben Sie beim Aufruf der Schreibfunktion den Dateinamen “Andere Datei” gewählt und einen neuen Dateinamen über die Tastatur eingegeben, so erscheint das Fenster “Neu”:
Bestätigen Sie dieses Fenster mit “Ja”, so wird ein neues File auf dem MDS angelegt, bevor die Daten auf den MDS geschrieben werden.
D-36
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Das Programm “FILEHANDLER”
5.4.4
Schreibe Datei auf STG RAM
Beim Speichern einer Datei wird der Dateiname, der im Editor angezeigt wird, als Default angezeigt. Den Dateinamen können Sie vor dem Abspeichern noch verändern. Der Filename kann aus bis zu 8 Zeichen bestehen. Beim Abspeichern wird dem Filenamen automatisch die Dateiendung .HEX angefügt.
5.4.5
Lese Verzeichnis vom MDS
Es wird das Dateiverzeichnis von einem MDS gelesen und in der Directory-An-
sicht auf dem Display dargestellt (siehe Kap. 5.3.2). Je nach MDS-Typ kann
dieser Vorgang einige Sekunden dauern.
5.4.6
Lese Verzeichnis vom STG RAM
Es wird das Dateiverzeichnis vom RAM des Handterminals (Laufwerk M:) ausgelesen und in der Directory-Ansicht auf dem Display dargestellt (siehe
Kap. 5.3.2). Im Display werden nur Dateien vom Typ *.HEX angezeigt. Ebenso
werden nur Dateien angezeigt und verwaltet, die sich in der Root-Directory des
Handterminal-RAM befinden.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-37
Das Programm “FILEHANDLER” A 05/07
5.4.7
Beispiel: Kopieren von Dateien
Die in diesem Kapitel beschriebenen Funktionen ermöglichen ein sehr einfaches Kopieren von Dateien. Dabei kann das Kopieren von MDS nach MDS oder von STG RAM nach MDS geschehen. Im Folgenden ist der Ablauf beschrieben, wenn eine Datei von einem ersten MDS nach einem zweiten MDS kopiert werden soll:
1. Die Funktion “Datei/Lese Verzeichnis vom MDS” (ALT + G) ausführen
2. Mit den Cursor-Tasten die zu lesende Datei auswählen
3. “Enter” drücken; der Lesebefehl wird gestartet. Nach dem Lesen werden die Daten im Editorfenster angezeigt
D-38
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Das Programm “FILEHANDLER”
4. Die Funktion “Datei/Schreibe Datei auf MDS” (ALT + W) ausführen
5. Filename “colour” auswählen
6. Überschreiben bestätigen
7. Länge bestätigen
Nach Ausführung dieser Funktionen sind die Daten der Datei “Delivery” nach “Colour” kopiert. Die Datei Colour erscheint jetzt ebenfalls mit einer Dateigröße von 300 Byte.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-39
Das Programm “FILEHANDLER” A 05/07
5.5
Das Befehle-Menü
Im Befehle-Menü finden Sie Befehle, die sich ausschließlich auf den MDS-Speicher beziehen.
5.5.1
Datei neu
Mit “Datei neu” legen Sie eine neue Datei auf dem MDS an. Der Dateiname darf auf dem MDS noch nicht vorhanden sein. Die neue Datei wird immer mit der Länge “0” angelegt.
5.5.2
Datei löschen
Diese Funktion löscht eine Datei auf dem MDS-Speicher.
Befinden Sie sich in der Directory-Ansicht, so können Sie die Löschfunktion sehr einfach durch Drücken der “Del”-Taste starten. Mit der “Del”-Taste können
Dateien vom MDS oder vom Handterminal gelöscht werden. Vom Handterminal werden die Dateien gelöscht, wenn die Directory-Ansicht die Dateien auf dem
STG Hand-Held Terminal PRO anzeigt.
5.5.3
MDS formatieren
Bevor ein MDS mit dem Filehandler betrieben werden kann, muss dieser formatiert werden. Vor dem Formatieren ist es wichtig, die Speichergröße des
MDS richtig einzustellen. Verwenden Sie hierzu die Funktion Extras/Parameter.
Das Formatieren löscht alle Daten auf dem MDS. Die Dateistruktur wird neu angelegt.
D-40
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Das Programm “FILEHANDLER”
5.5.4
Datei Attribut
Mit diesem Befehl können auf einzelne Dateien Zugriffsrechte vergeben werden. Damit sind die Dateien vor unberechtigtem bzw. unbeabsichtigtem Überschreiben geschützt. In der Directory-Ansicht wird das Dateiattribut in der rech-
ten Spalte angezeigt (siehe Kap. 5.3.2). Folgende Dateiattribute sind möglich:
Attribut
–
R
W
F
F/R
Beschreibung kein Attribut bzw. ein bestehendes Attribut wird damit gelöscht.
Read only; die Datei kann nur gelesen werden. Beschreiben, Überschreiben oder Löschen sind nicht möglich.
Write once; Die Datei kann einmalig beschrieben werden. Ein wiederholtes Beschreiben oder Löschen ist nicht möglich.
Feste Länge; die Datei kann beliebig gelesen werden. Das Schreiben ist nur zulässig, wenn die Länge der Datei nicht verändert wird. Anhängen von Daten bzw. Löschen der Datei ist nicht möglich.
Feste Länge und Read only ist gesetzt. Dieses Attribut hat die gleiche
Wirkung wie das “R”-Attribut.
Dateiattribute können nur auf MDS-Dateien vergeben werden. Dateien im RAM des Handterminals sind immer vom Typ “–”. D. h., sie können generell verändert oder gelöscht werden.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-41
Das Programm “FILEHANDLER” A 05/07
5.5.5
MDS Status
Dieser Befehl zeigt nacheinander in einigen Fenstern den Status des MDS an.
MDS-Typ:
Dieser Wert ist identisch mit der Angabe des
MDS-Typs beim Format-Befehl in einer SIMATIC.
BruttoMDS Groesse:
Hier wird die MDS-Grösse angezeigt, die beim
Format-Befehl eingestellt war.
ECC:
Zeigt an, ob der MDS mit oder ohne ECC betrieben wird.
MDS:
Zeigt den Namen des MDS an, der beim Format-
Befehl auf den MDS geschrieben wurde.
MDS Groesse:
Zeigt den maximal für den Anwender nutzbaren
Speicherbereich an.
Bytes frei:
Zeigt die Anzahl der Datenbytes an, die auf dem
MDS dem Anwender für seine Daten noch zur
Verfügung stehen.
Dir frei:
Zeigt die Anzahl der Dateien an, die noch auf dem
MDS angelegt werden können.
Bat 1:
Zustand der RAM-Batterie. Dieser Wert ist bei
EEPROM-MDS nicht relevant.
Bat 2:
Zustand der Dialogbatterie beim MDS 507.
Bearb.-anzahl:
Anzahl der Bearbeitungen, die mit dem MDS seit dem ersten Formatieren durchgeführt wurden. Der
Wert ist vor allem bei EEPROM-MDS wichtig, da diese Speichertypen nur eine begrenzte Schreibhäufigkeit besitzen.
ECC-Korrekt:
Zähler für die Anzahl der durchgeführten ECC-
Korrekturen. Hat dieser Zähler einen Wert ungleich Null, so ist der MDS demnächst auszutauschen. Ein EEPROM Speicher wurde zu häufig beschrieben.
D-42
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Das Programm “FILEHANDLER”
5.5.6
MDS Cover
Der Cover-Befehl verschließt die komplette Dateistruktur auf dem MDS. Ist ein
MDS “covered”, so kann
S jede Datei gelesen werden
S jede Datei beschrieben werden, solange die Dateilänge nicht verändert wird
S keine Datei gelöscht werden
S kein neues File angelegt werden
S mit Format der MDS neu initialisiert werden. Danach ist der MDS “uncovered”.
S mit einem Cover-Befehl und der Einstellung “nicht covered” der Cover-Zustand wieder aufgehoben werden.
5.6
Das Editor-Menü
5.6.1
Anzeige Verzeichnis
Diese Funktion schaltet das Display um in die Directory-Ansicht (siehe
Kap. 5.3.2). Dargestellt wird das zuletzt gelesene Directory. Das Directory kann
sowohl vom MDS als auch vom Handterminal sein.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-43
Das Programm “FILEHANDLER” A 05/07
5.6.2
Anzeige Editor
Diese Funktion schaltet das Display um in die Editor-Ansicht (siehe Kap. 5.3.1).
Es wird die Datei angezeigt, die zuletzt eingelesen wurde. Diese Datei kann sowohl vom MDS als auch vom Handterminal sein.
5.6.3
Datei Größe verändern
Die momentane Länge einer Datei wird im Editor in der zweiten Zeile dargestellt. Diese Länge kann mit dem Befehl “Datei Größe” verändert werden. Wird die Datei verlängert, so wird eine entsprechende Anzahl von Nullen (00 Hex) am Ende der Datei angehängt. Der angehängte Teil wird im Editor mit invertierten Ziffern dargestellt.
5.6.4
Anzeige löschen
Diese Funktion löscht den Speicher in der Editoranzeige. Dabei kann der hexadezimale Wert des Füllzeichens vorgegeben werden. Der Standardwert des
Füllzeichens ist 00hex. Nach dem Löschen werden alle Daten in der Anzeige invertiert dargestellt, um zu kennzeichnen, dass noch keine Daten vom Anwender eingegeben wurden.
5.6.5
Sprung an Adresse
Die normale Positionierung des Cursors innerhalb einer Datei erfolgt mit den
Cursor-Tasten. Bei größeren Dateien kann die Funktion “Sprung an Adresse” sehr vorteilhaft eingesetzt werden, um den Cursor an eine beliebige Stelle innerhalb der Datei zu positionieren. Die Funktion “Sprung an Adresse” kann sehr einfach auch über die Tab-Taste aufgerufen werden.
5.6.6
Anzeige Setup
Hier erfolgt die Einstellung der Anzeige. Die Darstellung kann im Hexadezimaloder ASCII-Format erfolgen. In der ASCII-Darstellung werden nicht darstellbare
Zeichen als weiße Felder angezeigt.
D-44
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07
5.7
Das Extra-Menü
Das Programm “FILEHANDLER”
5.7.1
Parameter
Mit der Funktion Parameter werden grundlegende Einstellungen für den Betrieb des Filehandlers vorgenommen.
Parameter Beschreibung
MDS Größe Hier wird die Brutto-Speichergröße des MDS eingestellt, mit dem gearbeitet werden soll.
MDS Typ
Die eingestellte Speichergröße wird in der Anzeige in der ersten Zeile angezeigt. Der Format-Befehl verwendet die Speichergröße für die
Festlegung des Dateisystems. Stimmt der Parameter “MDS Größe” nicht mit dem benutzten MDS überein, so kann trotzdem mit dem
MDS gearbeitet werden. Nur der Format-Befehl würde dann zu einem falschen Ergebnis führen.
Hier kann umgeschaltet werden zwischen RAM, EEPROM und
MDS 507. FRAM-Speicher werden behandelt wie RAM-Speicher. In der Einstellung EEPROM wird die Batterie-Fehlermeldung in der Anzeige unterdrückt, da diese MDS generell keine Batterie besitzen. In der Einstellung MDS 507 wird auch die Dialogbatterie ausgewertet und zur Anzeige gebracht, wenn sie entladen ist.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-45
Das Programm “FILEHANDLER” A 05/07
Parameter Beschreibung
ECC Ein-/Ausschalten des ECC-Treibers
SLG Nr. Hex
EAKO
Die hier eingestellte SLG Nr. wird beim Bearbeiten eine MDS in den
Systembereich des MDS geschrieben. Sie hat primär keine Wirkung auf die Funktion des Programmes Filehandler im STG Hand-Held
Terminal PRO .
Die Ein-/Auslaufkontrolle (EAKO) kann beim Filehandler im STG
Hand-Held Terminal PRO nicht eingestellt werden. Das STG Hand-
Held Terminal PRO arbeitet generell ohne Ein-/Auslauf-steuerung
(EAKO = “4”)
5.7.2
Passwort für Filehandler
Das Passwort für Filehandler schützt den Anwender davor, dass unberechtigte
Benutzer des STG Hand-Held Terminal PRO Daten auf dem MDS manipulieren können. Die Passwörter für die Programme “Filehandler” und “MOBY D/E/I” sind identisch. Beschreibung zur Handhabung des Passworts siehe in
5.7.3
Kommunikation
Die Kommunikation des Filehandlers ist grundsätzlich auf den “Lesekopf” eingestellt. Optional kann der Filehandler auf “ASM an RS232” umgestellt werden.
Damit kann eine Baugruppe vom Typ ASM420-RS232 an das Handterminal an-
geschlossen werden. Weitere Hinweise finden Sie im Kap. 6.5.
Bitte beachten Sie, dass eine Baugruppe vom Typ ASM 421 nicht am STG
Hand-Held Terminal PRO betrieben werden kann.
5.8
Die Funktionen “?”
Die hier aufgeführten Funktionen sind identisch mit den Programmen
MOBY D/E/I. Siehe hierzu Kap. 4.6.
D-46
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Erweiterte Funktionen
6 Erweiterte Funktionen
6.1
Die Hinterlegung der MDS-Daten im
Handterminal
Die vom MDS gelesenen Daten werden auf dem Handterminal automatisch in einer Datei mit dem Namen “READ_D.HEX”, “READ_E.HEX” oder
“READ_I.HEX” im Verzeichnis /SIBO/M des PSION Workabout PRO hinterlegt.
Jeder weitere Lesebefehl überschreibt diese Datei.
Beim Beschreiben des MDS werden die Schreibdaten aus dem Editor auf den
MDS geschrieben und außerdem unter dem Namen “WRITE_D.HEX”,
“WRITE_E.HEX” oder “WRITE_I.HEX” auf das Verzeichnis /SIBO/M des PSION
Workabout PRO gespeichert. Jeder weitere Schreibbefehl überschreibt diese
Datei.
Über die Funktion ”Datei/Laden Datei” wird eine zuvor abgespeicherte Datei in den Editor geladen. Geben Sie dazu den Namen der Datei ohne die Erweiterung “.HEX” ein.
Sie können sich auch eine Auswahl der abgespeicherten Dateien anzeigen lassen, indem Sie das Eingabefeld leer lassen und die ENTER-Taste bestätigen.
Mit den Cursor-Tasten wählen Sie nun die entsprechende Datei aus.
Die Funktion “Datei/Speichern” speichert die Daten vom Editor in eine Datei mit der Dateiendung “.HEX” und zugleich die ID-Nummer in eine Datei mit der
Dateiendung “.HX1” auf das Verzeichnis /SIBO/M des PSION Workabout PRO.
Sie können einen beliebigen Namen mit 1 bis 8 alphanumerischen Zeichen eingeben.
Hinweis
Wenn Sie Daten vom MDS lesen, im Editor modifizieren und dann abspeichern, werden die modifizierten Daten auf die .HEX-Datei gespeichert.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-47
Erweiterte Funktionen
A 05/07
6.2
Kopieren von MOBY-Daten von und zum
STG Hand-Held Terminal PRO
6.2.1
Was wird zusätzlich benötigt?
S Workabout PRO Docking Station (Bestellnummer siehe Katalog)
S USB-Treiber für STG Hand-Held Terminal PRO
Ist auf der CD “RFID Systeme Software & Dokumentation” ab Ausgabestand 07/2007 enthalten (Bestellnummer 6GT2080-2AA10)
S Microsoft Active Sync ab Version 3.4
Hinweis
Download von Microsoft Active Sync
Microsoft Active Sync ist nicht Bestandteil des Lieferumfangs. Die aktuelle Version der Applikation kann unter www.microsoft.com heruntergeladen werden.
D-48
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Erweiterte Funktionen
6.2.2
Installation
1. Microsoft Active Sync auf PC installieren
2. USB-Treiber für STG Hand-Held Terminal PRO auf PC installieren
3. Partnerschaft zwischen PC und STG Hand-Held Terminal PRO herstellen
Microsoft Active Sync auf PC installieren
Mit Microsoft Active Sync können Sie Dateien zwischen Ihrem PC und dem
STG Hand-Held Terminal PRO synchronisieren und Applikationen auf den Reader übertragen. Des Weiteren wird der Reader bei einer Active Sync-Verbindung als Laufwerk im Windows Explorer unter Mobile Device ansprechbar. Nähere Informationen zu Microsoft Active Sync können Sie der beigefügten
Hilfe-Datei entnehmen.
Sollte auf Ihrem PC kein Microsoft Active Sync oder eine niedrigere Version als
3.4 installiert sein, dann installieren Sie die von Microsoft angebotene aktuelle
Version.
Achtung
Update / Neuinstallation von Microsoft Active Sync
Bevor Sie Microsoft Active Sync updaten oder neu installieren, müssen Sie die alte Version deinstallieren.
Gehen Sie bei der Installation von Microsoft Active Sync wie folgt vor:
1. Starten Sie das Installationsprogramm durch einen Doppelklick auf die Datei msasync.exe.
2. Folgen Sie den Bildschirmanweisungen.
Hinweis
Standard Sync-Ordner
Zum Abschluss der Installation legt Microsoft Active Sync auf dem
Desktop Ihres PC standardmässig den Ordner Workabout Pro My
Documents an.
Wenn Sie im Active Sync Einstellungen-Menü unter Sync Options die Option Data anwählen, dann wird der Inhalt des Desktop-Ordners bei jedem Active Sync-Vorgang mit dem Inhalt des Ordners My
Documents auf dem Reader synchronisiert.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-49
Erweiterte Funktionen
A 05/07
USB-Treiber für STG Hand-Held Terminal PRO auf PC installieren
Hinweis
Windows XP: Kompatibilitätstest ignorieren
Während der Installation des USB-Treibers kann es unter Windows XP zu der Meldung kommen, dass der Treiber den Kompatibilitätstest nicht bestanden hat. Ignorieren Sie diese Meldung und setzen Sie die Installation fort.
Gehen Sie bei der Installation des USB-Treibers für den STG Hand-Held Terminal PRO wie folgt vor:
1. Verbinden Sie den STG Hand-Held Terminal PRO über Docking Station mit einem freien USB-Port Ihres PC.
2. Schalten Sie den STG Hand-Held Terminal PRO ein.
3. Legen Sie die CD ” RFID Systeme Software & Dokumentation ” in das Laufwerk Ihres PC ein.
4. Starten Sie das Installationsprogramm durch einen Doppelklick auf die Datei
\daten\STG_PRO\USB_Driver\usbsetup.exe.
5. Wählen Sie unter Select Device die Option Workabout Pro.
6. Folgen Sie den Bildschirmanweisungen.
Partnerschaft zwischen PC und STG Hand-Held Terminal PRO herstellen
Damit Microsoft Active Sync den STG Hand-Held Terminal PRO erkennt, muss eine Partnerschaft zwischen dem PC und dem Reader hergestellt werden.
1. Gehen Sie bei der Herstellung der Partnerschaft wie folgt vor:
2. Verbinden Sie den STG Hand-Held Terminal PRO über das USB-Kabel mit einem freien USB-Port Ihres PC.
3. Schalten Sie den STG Hand-Held Terminal PRO ein.
4. Microsoft Active Sync startet automatisch und erkennt den Reader als neues
Gerät. Quittieren Sie die Frage, ob eine Partnerschaft zwischen dem PC und dem Reader hergestellt werden soll, mit Yes.
5. Folgen Sie den Bildschirmanweisungen.
D-50
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Erweiterte Funktionen
6.2.3
Daten Austausch
Vorraussetzung:
Eine Partnerschaft zwischen STG Hand-Held Terminal PRO und PC muss be-
Im Windows Explorer erscheint ein neues Icon “Mobile Device”. Mit Doppelklick auf das Icon wird das Filesystem des STG Hand-Held Terminal PRO geöffnet.
Alternativ können Sie im Programm ActiveSync die Schaltfäche “Explore” drücken, oder das Menü “File/Explore” auswählen.
Öffen Sie im Explorer durch Doppelklick das Verzeichnis “SIBO” und dannach das Verzeichnis “M”. Dort finden Sie unter anderem die Dateien
“READ_D.HEX”, “READ_E.HEX” bzw. “READ_I.HEX” und die von Ihnen abgespeicherten Daten mit der Endung “.HEX”. Nun können Sie per Ziehen und Ablegen die Dateien vom STG Hand-Held Terminal PRO auf den PC kopieren.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-51
Erweiterte Funktionen
A 05/07
Die Datei READ bzw. WRITE hat eine Länge entsprechend der Größe des gelesenen MDS:
READ_D.HEX: 44 Byte bei I-Code1
112 Byte bei I-Code SLI
256 Byte bei Tag-it HF-I
992 Byte bei my-d
READ_E.HEX: 768 Byte bei MOBY E(im Normalmodus)
1024 Byte bei MOBY E(nach dem Lesen der Rohdaten)
1024 Byte bei MOBY E(im SIM-Modus)
READ_I.HEX:
Setup-Einstellung ohne ECC mit ECC
62 Byte
128 Byte
2 KB
8 KB
32 KB
62
128
2045
8189
32765
42
112
1778
7154
28658
Der Inhalt der Datei kann nun mit einem entsprechenden Editor am PC angezeigt und verändert werden:
Wenn vom MDS ASCII-Daten gelesen wurden:
Jeder Editor kann verwendet werden: NOTEPAD, WRITE, WORD usw.
Wenn binäre Daten mit dem MDS ausgetauscht werden:
Verwendung eines HEX-Editors. HEX-Editoren sind auf dem Sharewaremarkt (z. B. Hedit usw.) oder auf dem professionellen Markt verfügbar
(z. B. “Codewright”).
D-52
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Erweiterte Funktionen
6.2.4
Die Organisation der Datei READ.HEX
In der Datei READ_x.HEX stehen nur die reinen Daten, die auch auf dem MDS vorhanden sind. Die Länge der Datei ist identisch mit der Größe des MDS (in
Bytes).
6.2.5
Die Organisation der Datei READ.HX1
In der Datei READ_x.HX1 ist die ID-Nummer hinterlegt. Die Datei READ_x.HX1
wird nur bei MOBY D/E angelegt.
6.3
Funktionen mit dem PSION-Betriebssystem
Über den Menübefehl DATEI/BEENDEN gelangen Sie auf die Betriebssystemebene des Handterminals. Im Folgenden sind einige Möglichkeiten aufgezeigt, die mit dem Windows CE-Betriebssystem möglich sind:
Hinweis
Diese Funktionen sind nur im “Supervisor” Modus ausführbar (siehe
S Einstellen und Konfigurieren des STG Hand-Held Terminals PRO
S Editieren der gelesenen MOBY-Daten mit dem PSION-Editor. Das ist jedoch nur möglich, wenn die MDS-Daten im ASCII-Format vorliegen.
S Tabellenkalkulation
S Rechner
S Ausführen von Befehlen
Eine genaue Beschreibung der Betriebssystemfunktionen und Standardprogramme entnehmen Sie dem Manual “PSION Teklogix Workabout PRO Hand-
Held Computer User Manual”. Dieses kann von PSION bestellt werden (siehe
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-53
Erweiterte Funktionen
A 05/07
6.4
Die automatische Stromsparfunktion
Das PSION Workabout PRO besitzt eine automatische Abschaltung. Diese wird aktiviert, nachdem ca. 5 Minuten keine Taste am PSION Workabout PRO betätigt wurde.
Darüberhinaus besitzen die Programme “MOBY D/E/I” eine weitere Stromsparfunktion. Wird 30 Sekunden nach Start eines MDS-Befehls kein MDS erkannt oder wird der in Bearbeitung befindliche MDS für länger als 30 Sekunden aus dem Feld bewegt, so wird der laufende MDS-Befehl unterbrochen. Es erscheint folgende Meldung:
Sie können jetzt den Befehl mit ESC komplett abbrechen oder mit ENTER fortsetzen. Beim Fortsetzen wird der unterbrochene Befehl an der Stelle fortgesetzt, an welcher er unterbrochen wurde.
D-54
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Erweiterte Funktionen
6.5
Anschluss von SIM-Geräten (MOBY E/I)
An der RS 232-Schnittstelle des PSION Workabout PRO ist es möglich, ein
MOBY E SIM anzuschließen. Das Anschlussschema kann dem folgenden Bild entnommen werden. Mit der Funktion “Extras/KOMMUNIKATION/PROTO-
KOLL” muss vor der Inbetriebnahme auf MOBY E/SIM oder ASM 420/I umgeschaltet werden.
In dieser Konfiguration kann sowohl mit dem “MOBY”-Programm als auch in
Anwenderapplikationen mit der MOBY-Library (vgl. Anhang A.2) mit dem SIM
gearbeitet werden.
MOBY E/SIM:
Kabel (6GT2391-1DH50) und
Netzteil (6GT2090-0HB00)
AC 220 V
DC 24 V
Hinweis
Das SIM von MOBY E arbeitet standardmäßig im zyklischen Betrieb.
Deshalb dauert die Abarbeitung eines Lese-/Schreibbefehls sehr viel länger als beim STG-Lesekopf. Eine Umschaltung des SIM in den schnellen Lesemodus ist mit dem Befehl Extras/MOBY E Setup/
FELDBETRIEBSART möglich. Die Umschaltung des SIM muss nach jedem Einschalten des SIM erfolgen.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-55
Erweiterte Funktionen
A 05/07
ASM 420/I:
Bei dieser Einstellung kann ein ASM 420/RS232 an das Handterminal angeschlossen werden. Das Verbindungskabel muss entsprechend der
ASM 420-Dokumentation angefertigt werden. Beim Programm “MOBY I” wird im ASM 420-Betrieb immer der MOBY V-Treiber eingeschaltet. Damit kann das
SLG 65 am ASM 420 betrieben werden.
MOBY I-SLG können eingeschränkt betrieben werden.
Belegung der RS 232-Schnittstelle am Handterminal:
2
3
5
Pin Benennung
TxD
RxD
Gnd
D-56
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Erweiterte Funktionen
6.5.1
Sicherheit
Das STG Hand-Held Terminal PRO hat zwei Betriebsmodi:
S Supervisor Modus
Konfiguration und Einstellungen für das STG Hand-Held Terminal PRO.
Nicht notwendig wenn die MOBY Service und Testprogramme benutzt werden.
S User Modus
Voreingestellter Modus. Der Anwender kann nur die installierten Serviceund Testapplikationen benutzen. Die Startmenü-Funktionalität ist eingeschränkt.
Der Betriebsmodus kann über die “Security Level”-Einstellungen umgeschaltet werden.
Dazu öffnen Sie zuerst das Startmenü durch das nacheinander Drücken der
Tasten “CTRL” + “ESC”.
Danach wählen sie über Cursor das Menü “Securtiy” an.
Der Wechsel zum Supervisor Modus ist durch ein Passwort geschützt. Im Auslieferungszustand ist dieses Passwort auf “123456” gesetzt und sollte bei der ersten Benutzung zur Sicherheit geändert werden.
Achtung
Die Dateien mit der Endung “.PFL” im Verzeichnis “Flash Disk” dienen zum Wiederherstellen des Auslieferungszustandes und dürfen daher nicht verändert oder gelöscht werden. Wenn Sie in den Supervisor Modus wechseln, sollten Sie als erstes eine Sicherungskopie dieser Dateien anlegen und an einen sicheren Ort verwahren.
Um das STG Hand-Held Terminal PRO wieder in den Auslieferungszustand zu versetzen, kopieren Sie die gesicherten Dateien wieder in den Ordner “Flash Disk” und führen Sie danach einen
System-Reset durch (siehe Kapitel 6.6).
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-57
Erweiterte Funktionen
A 05/07
Hinweis
Sind die Dateien mit der Endung “.PFL” beschädigt oder verloren gegangen, so kann der Ursprungszustand des Geräts nur im Werk wiederhergestellt werden.
6.6
System-RESET
Einen System-RESET führt das Handterminal nach dem Einlegen der Batterien beim ersten Einschalten durch. Dieser RESET ist einem Hardware-RESET gleichzusetzen.
Ein System-RESET kann auch manuell herbeigeführt werden. Hierzu muss sich das STG Hand-Held Terminal PRO im Supervisor Modus befinden (siehe
Kapitel 6.5.1) Danach lösen Sie den System-Reset im Startmenü durch Betäti-
gen der Funktion “Shutdown/Cold Reset” aus.
Beim System-RESET
S bleiben gespeicherte Daten im Flash-Speicher immer erhalten (Verzeichnis
“Flash Disk”),
S gehen die Daten im RAM-Speicher (z. B. SIBO/M) verloren.
Das Password für den Supervisor Modus wird wieder auf den Initalwert zurückgesetzt.
D-58
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Fehlermeldungen
7 Fehlermeldungen
Was tun, wenn...
... beim MOBY Lesen/Schreiben die PSION-Anzeige erlischt?
S Die Batterien auf dem PSION Workabout PRO sind leer. Gerät in die Ladeschale stecken oder neue Batterien einsetzen.
... am Display nach dem Einschalten nichts zu erkennen ist?
S Die Batterien sind leer.
7.1
Fehlermeldungen bei den Programmen
“MOBY D/E/I”
Die Meldungen der folgenden Tabellen können beim Betrieb auftreten. Die Anzeige erfolgt in einem eigenen Fenster. Eine Meldung kann folgende Form haben:
Fehlerart genaue Fehlerbezeichnung
Die Meldung ist in mehreren Zahlen verschlüsselt. Sie hat die Form xx/yy/zz und dient zur genauen Fehleranalyse. In den folgenden Tabellen werden die Fehlerarten und Fehlerbezeichnungen detailliert aufgelistet. Die Information /zz kann bei einigen
Meldungen auftreten. zz beinhaltet weitere
Fehlerinformation (z. B. Block, bei welchem der Fehler auftrat).
Fehlerart
1 bis 2
3 bis 9
10 bis 15
20
30 bis 37
42 bis 45
52 bis 57
60 bis 72
Beschreibung
Allgemeine Fehler
MOBY E-Fehler reserviert
Timer-Fehler
MOBY I-Fehler
MOBY D-Fehler
MOBY D ISO-Fehler reserviert
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-59
Fehlermeldungen A 05/07
Fehlerbezeichung Mögliche Fehlerursachen und deren Behebung
1, 2, 3, 4, 5, 6
7
10, 11, 12
20
21
22 bis 27
32
33, 34, 35, 36
37
38
S Lesegerät sendet kein Startprotokoll
S Lesekopf angeschraubt?
S Passt der Lesekopf zur Protokolleinstellung? (siehe Menü:
Extras/KOMMUNIKATION)
S Akkus im Lesegerät sind entladen (eventuell sind Akkus defekt)
S interner Programmfehler
Schnittstelle defekt
Lesegerät sendet keine oder eine fehlerhafte Antwort
(MDS D1xx/MDS F4xx)
S Lesegerät sendet keine Antwort
S Parameter im Menü Extras/KOMMUNIKATION überprüfen.
Bei SIM-Betrieb muss bei “Schnittstelle” und “Protokoll” auf
SIM umgestellt werden.
S Akkus im Lesegerät sind entladen (eventuell sind Akkus defekt)
Lesegerät sendet keine oder eine fehlerhafte Antwort
S interner Programmfehler (MDS D1xx)
S Lesegerät sendet falsche Antwort
S MDS ist nicht mit dem MOBY-Schlüssel personalisiert
S interner Programmfehler (MDS D1xx/MDS F4xx) unzulässige Anforderung, interner Programmfehler
S Kontakt zum Lesekopf überprüfen
S Lesegerät sendet keine Antwort (MDS E6xx) interner Programmfehler
S STG-Programm beenden und neu starten
S Schreib-/Lesefehler (MDS F4xx)
S Lesekopf liefert eine Fehlermeldung
S Lesekopf ist fehlerhaft
S CRC-Fehler vom MDS; Kommunikationsfehler zum MDS;
MDS im Grenzbereich
S MDS hat einen Defekt
S interner Programmfehler angegebener Block ist schreibgeschützt
39
40, 41, 42
Mehrere MDS sind im Feld
S interner Programmfehler (MDS D1xx)
Lesegerät sendet keine oder eine fehlerhafte Antwort
(MDS D1xx)
S interner Programmfehler (MDS D1xx)
D-60
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Fehlermeldungen
66
67
70
Fehlerbezeichung Mögliche Fehlerursachen und deren Behebung
43
45
50
52, 53, 54, 55,
56, 57
63
Benutzerabbruch durch ESC falsche Antwort des Lesegerätes
Fehler während Lesen bzw. Schreiben der MDS-Daten interner Programmfehler mit MOBY-Lesekopf
65
80
81, 82
101 bis 132
Authentifizierungsfehler; der MDS besitzt nicht den MOBY-
Schlüssel
S Eventuell über “Extras/MOBY E Setup” den Schlüssel “B” einstellen.
Schnittstellenfehler; erscheint beim Anschluss eines SIM.
S Parameter im Menü Extras/KOMMUNIKATION überprüfen
S Stecker und Kabel zum SIM überprüfen allgemeiner Lese-/Schreibfehler des MOBY-Lesekopfes interner Programmfehler mit MOBY-Lesekopf
S Schreiben nicht erfolgreich
S mehrere Tags im Feld
MDS-Typ an Lesegerät wird nicht unterstützt
S Lesegerät sendet falsche Antwort
S MDS ist nicht mit dem MOBY-Schlüssel personalisiert
Lesegerät sendet Fehler (MOBY I)
Spezifikation bestimmter Fehler:
101 Anwesenheitsfehler
S Es befindet sich kein MDS im Feld, der die im Befehl vorgegebene MDS-Identnummer besitzt.
103
104
105
106
Fehler in der Verbindung zum SLG
S Die Hardware des Lesekopfes hat einen Defekt
Fehler im Speicher des MDS
S INIT-Befehl durchführen; zuvor muss die Speichergröße des
MDS über “Extras/MOBY I Setup” richtig eingestellt werden.
S Der MDS ist defekt.
MOBY-Befehl vom Lesekopf nicht interpretierbar
S Die eingestellte Speichergröße über “Extras/MOBY I Setup”
überprüfen
S Feldstörung am Lesekopf: Externes Störfeld
S Der MDS hat während der Kommunikation das Feld verlassen.
S Feldstörung während der Kommunikation
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-61
Fehlermeldungen A 05/07
Fehlerbezeichung Mögliche Fehlerursachen und deren Behebung
107
109
110 zu viele Sendefehler; der MDS konnte die Daten vom Lesekopf nicht richtig empfangen.
S Das MDS steht im Grenzbereich des Lesekopfes
CRC-Fehler bei der Initialisierung des MDS durch Feldstörung.
MDS lässt sich nicht initialisieren und ist defekt.
111
112
113
114
115
125
129
130
180 bis 243
Timeout beim Initialisieren (MOBY I)
S Der MDS steht im Grenzbereich des Lesekopfes.
S Es wird ein MDS 507 initialisiert und der MDS507-Betrieb
über “Extras/MOBY I Setup” ist nicht eingeschaltet.
S Der MDS-Speicher ist nicht beschreibbar und ist defekt.
S Das erneute Schreiben in den OTP-Speicher ist nicht zulässig.
Der Adressbereich des MDS wurde überschritten.
S Die eingestellte Speichergröße über “Extras/MOBY I Setup” prüfen.
ECC-Fehler bzw. der MDS ist nicht im ECC-Modus initialisiert.
S Über “Extras/MOBY I Setup” den ECC Betrieb einschalten und anschließend den Init-Befehl durchführen.
Resetmeldung nach Spannungswiederkehr:
S Handterminal hat einen Defekt in der Spannungsversorgung zum Lesekopf (evtl. Batterien aufladen/austauschen).
S Die Hardware des Lesekopfes hat einen Defekt.
interner Programmfehler: vorheriger Befehl aktiv
Die Anzahl der im Feld befindlichen MDS ist unzulässig. Anzahl MDS > Multitag in der Funktion SLG-Status unter “Extras”.
interner Programmfehler; der Telegrammaufbau des Befehls zum Lesekopf ist falsch interner Programmfehler (MDS D1xx)
251
255
Schalten Sie das Gerät aus und wieder ein. Bei wiederholtem
Auftreten des Fehlers melden Sie sich mit der Angabe der Fehlernummer beim Customer Support.
Schreib-/Lesevergleich war nicht erfolgreich keine Karte/kein MDS im Feld
D-62
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Fehlermeldungen
7.2
Fehlermeldungen beim Programm
“FILEHANDLER”
Die Meldungen der folgenden Tabelle können beim Betrieb des Filehandlers auftreten. Eine Filehandler-Fehlermeldung hat die folgende Form:
Fehlerart
genauer Filehandlerfehler
Der Filehandlerfehler wird in der gleichen
Art und Weise dargestellt wie auch beim
Filehandler in der SIMATIC. Es ist ein Alphazeichen, gefolgt von einer 3-stelligen Nummer. Die Fehlercodes sind weitgehend identisch mit den Fehlernummern aller MOBY-
Filehandler-Anschaltungen.
C008
C009
C010
C011
C012
C013
C014
C015
C016
Filehandlerfehler
A006
A011
A015
A016
A020
B001
C002
C006
C007
C017
Fehlerbeschreibung, Ursache und Behebung
Unbekannter Befehl, die Kommandokennung KK ist nicht zulässig
Beim 1. Befehlsblock DBN nicht 1; bei Folgeblock KK oder DBN falsch
Checkbyte-Error beim Empfang von S5
Befehl vom anderen Absender in Bearbeitung falsche Anzahl von Zeichen im Telegramm
Fehler in Verbindung zum SLG; Lesekopf defekt
Fehler im RAM des MDS; MDS wechseln, FORMAT durchführen
Anwesenheitsfehler; MDS steht im Grenzbereich
Parametrierfehler bei FORMAT; Befehl nicht interpretierbar
Zu viele Sync-Versuche; Feldstörung am Lesekopf
Zu viele Sendefehler
CRC-Sendefehler
FORMAT, CRC-Fehler beim Empfang
FORMAT, MDS lässt sich nicht initialisieren
FORMAT, Timeout; MDS steht im Grenzbereich
FORMAT, not initialized; Extras/Parameter überprüfen
CMD Adressfehler; Extras/Parameter überprüfen
ECC-Fehler; MDS neu formatieren; ECC Betrieb abschalten
Allgemeiner Treiberfehler
Fehlerart
Protokollfehler
SLG-Fehler
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-63
Fehlermeldungen A 05/07
H140
H141
H142
H143
H144
H145
H146
H147
H148
H149
H150
H151
H152
H153
Filehandlerfehler
D001
D005
D009
D014
D015
D018
D022
D023
E001
E002
E003
E005
F001
F005
Fehlerbeschreibung, Ursache und Behebung
Nur RESET-Befehl zulässig
Unzulässige Parameter bei FORMAT, CREATE,
WRITE, UPDATE oder ATTRIB
RESET-Befehlsparameter falsch
CREATE und WRITE: Der Nutzdatenbereich auf dem
MDS ist voll belegt
Nur FORMAT-Befehl möglich; MDS nicht identifiziert
Anfangsadresse im Befehl ist außerhalb des Datenbereiches (Anfangsadresse > Dateilänge)
Directory und/oder FAT-verändernder Zugriff auf einen mit COVER geschützten MDS unzulässig.
COVER: MDS-Name falsch
Der MDS-Typ ist falsch oder passt nicht zur eingestellten Betriebsart (ECC).
CREATE-Befehl: kein Directory-Eintrag mehr frei
CREATE-Befehl: Datei bereits im Directory vorhanden
Bei READ oder WRITE wird ein FAT Blockfolgefehler festgestellt, die FAT ist defekt
Die angesprochene Datei ist nicht vorhanden
WRITE/UPDATE/DELETE-Befehl auf eine Datei, die mit entsprechendem Attribut geschützt ist
Serielle Schnittstellen Fehler
Falsche Schnittstelle fehlerhafter Timer
Schnittstellen-Fehler
Startprotokoll Fehler
Reset-Fehler, WRITE
Reset-Fehler, READ, kein STX
Reset-Fehler, READ, Timeout
Reset-Fehler, READ, Falsche Antwort
Start-Fehler, WRITE
Start-Fehler, READ, kein STX
Start-Fehler, READ, Timeout
Start-Fehler, READ, Falsche Antwort
Start-Fehler, WRITE, Länge zu groß
Fehlerart
Auftragsbezogene
Fehler
Directorybezogene
Fehler
Dateibezogene Fehler
Fehlermeldung der
Filehandler-
Applikation
D-64
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Technische Daten
8 Technische Daten
Hardware
Prozessor
RAM-Speicher
ROM-Speicher
Bildschirm
Tastatur
Touch
Intel XScale PXA
128 MB; davon sind ca. 40 MB frei verwendbar
64 MB für Betriebssystem und Flash Disk.
Ca. 40 MB können für die Dateiablage genutzt werden.
Grafischer LCD-Bildschirm mit 240x320 Bildpunkten; Farbe
Alphanumerisch
Touchbedienung mit Stift oder Finger
Sound Interner Lautsprecher
Stromversorgung Lithium Ion wiederaufladbare Batterie
Schnellladefähig; automatische Abschaltung
Betriebsdauer: ca. 20 Stunden
(Lesekopf inaktiv, Display unbeleuchtet)
8 Stunden
(Lesekopf aktiv)
Backup-Batterie: 3 V Lithium Ion-Zelle, wiederaufladbar
Schnittstellen LIF-Schnittstelle (Low Insertion Force Schnittstelle) für Batterieladung und Kommunikation mit PC;
RS 232- und TTL-Schnittstelle zum Anschluss eines MOBY-
Lesekopfes
Software
Betriebssystem
Dateiverwaltung
Integrierte
Software
Windows CE 4.2 mit SIBO C Emulation
Windows kompatibel
MOBY Service- und Testprogramm
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-65
Technische Daten
Technische
Daten
Abmessungen
Gewicht
Temperatur
Relative
Feuchtigkeit
Schutzart
Schlagfestigkeit
EMV
Komplettgerät
(inkl. Akkus)
90 x 305 x 44 [mm] ca. 460 g
Lesekopf/Antenne
90 x 64 x 35 [mm] ca. 100 g
Betrieb: –10 ° C bis +50 ° C
Lagerung: –25 ° C bis +60 ° C (ohne Batterie)
5 % bis 90 % nicht kondensierend
IP54 (spritzwassergeschützt)
Max. Fallhöhe auf Beton:
EN 55022, EN 55024
1
1,2 m
1 Bei Handterminal STG U nur für Komplettgerät mit PSION Workabout PRO
A 05/07
D-66
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07 Technische Daten
RF-Schreib-/Lesekopf
MOBY D 13,56 MHz (I-Code; Tag-it) max. Leseentfernung: 60 mm mit MDS D139
25 mm mit MDS D160
30 mm mit MDS D124
Labels auf Basis I-Code in der Standardgröße
(ca. 85 x 55 mm): max. Leseentfernung: 75 mm mit I-Code1
100 mm mit I-Code SLI
100 mm mit Tag-it HF-I
100 mm mit my-d
MOBY E
MOBY I
Zulassungen: ETS 300 330
13,56 MHz (MIFARE) max. Leseentfernung: 30 mm mit MDS E611
18 mm mit MDS E600
8mm mit MDS E624
4mm mit MDS E623
3mm mit MDS E623, eingebaut in Metall
Zulassungen: ETS 300 330 Reg. Nr. G100213L
FCC ID: KR5MIS
1,81 MHz (Daten); 134 kHz (Energie)
MDS-Typ max. Leseentfernung (mm)
401/402
404/514/413E
403
506
439E
507 mit Batterie
507 ohne Batterie
Zulassungen:
6
20
8
12
12
35
4
ETS 300 330 Reg. Nr. TTI-P-G 128/96
FCC ID: KR5MIS-I
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-67
Anhang A 05/07
A Anhang
A.1
Bestellung von Komponenten für erweiterte
Funktionen
Für die erweiterten Funktionen des STG Hand-Held Terminal PRO werden
Komponenten benötigt, die nicht von Siemens A&D geliefert werden.
Wenn Sie diese Komponenten für Ihre MOBY-Anwendung benötigen, dann wenden Sie sich bitte direkt an PSION bzw. dessen Vertretung in Ihrem Land.
Adressen und Bestelllisten von PSION finden Sie im Internet unter www.psionteklogix.com
. Die PSION-Vertretung in Ihrem Land finden Sie ebenfalls unter dieser Internet-Adresse.
In Deutschland werden die PSION-Komponenten von der Fa. WAROK
(Tel. 07721/202630) geliefert.
Optional werden für die STG-Anwendung folgende Komponenten benötigt:
Bestellbezeichnung Anmerkung
Active Sync Ist alternativ unter der Microsoft
Internet-Adresse frei verfügbar
User Guide für PSION Workabout PRO Fragen Sie Ihre PSION-Vertretung
Weitere PSION-Komponenten, wie
S Schnelladegeräte
S PSION Workabout PRO mit numerischer Tastatur fragen Sie bitte ebenfalls direkt bei PSION oder deren Vertretung an. Diese
Komponenten werden nicht für die STG-Anwendung benötigt. Sie werden wichtig, wenn Sie Ihre eigene Identanwendung auf dem Handterminal programmieren möchten.
D-68
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07
A.2
Portieren von Anwenderapplikationen
Anwenderapplikation, die für das Vorgängermodell auf Basis des
Workabout MX entwickelt wurden, lassen sich auf dieses Gerät portieren.
Hinweis
Neuentwicklungen von Anwenderapplikationen sind möglich, aber nicht empfehlenswert. Neue Projekte sollten auf die nächste Gerätegeneration warten.
Was wird benötigt?
Für Anwenderapplikationen wird das C-Entwicklungspaket von PSION und das embedded Visual Studio von Microsoft benötigt.
Package
USB Driver
Active Sync
PSION Teklogix
Mobile Device
SDK
Embedded
Visual C++ 4.0
SIBO_CandOP_ for_
WindowsCE_p5
Comment
Notwendig um das STG Hand-
Held Terminal
PRO über den
USB Port am PC zu erkennen
Kommunikation zwischen PC and
WinCE basierte
Geräte
Software development kit für
Workabout PRO
Vendor
PSION
Teklogix
Where to get?
Internet: www.psionteklogix.com
RFID Systeme Software &
Dokumentation
Microsoft Internet:
1 www.microsoft.com/ downloads
Entwicklungsumgebung (Compiler)
SIBO to Windows
CE Migration kit
PSION
Teklogix
Internet: www.psionteklogix.com
Developer Resources section of Teknet page
Microsoft Microsoft
PSION
Teklogix
Internet: www.psionteklogix.com
Developer Resources section of Teknet page
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-69
A 05/07
Package
MOBY.LIB
Comment
Anbindung der
MOBY RFID
Module
1 Bestell-Nummer 6GT2080-2AA10
Vendor Where to get?
SIEMENS RFID Systeme Software &
Dokumentation 1
Ausführlicher Beschreibungen und mögliche Einschränkungen sind im “SIBO to
Windows CE Migration Kit” dokumentiert.
Die MOBY-Library
Es steht eine Library für MOBY D, MOBY E und MOBY I zur Verfügung. Die
Library (MOBY D/E/I) ist auf der CD “RFID Systeme Software & Dokumentation” ab Ausgabestand 07/2007 (Bestellnummer 6GT2080-2AA10) enthalten.
Ebenfalls enthalten ist die entsprechende Beschreibung der Schnittstellenbefehle.
Zu beachten ist, dass die Library nicht identisch mit der Vorgängerversion auf
Basis Workabout MX ist.
In den folgenden Tabellen sind die implementierten Befehle zusammengefasst:
MOBY D-Library
Funktionsaufruf
RF_ReadBlock
RF_WriteBlock
RF_ReadTagId
RF_Status
RF_Init nMobyDOpen vMobyDClose
Kurzbeschreibung
Liest einen Block vom MDS
Schreibt einen Block
Selektiert den Tag. Liest die TagId
Ermittelt den Tag-Typ
Beschreibt alle Benutzerblöcke
Öffnet eine Schnittstelle
Schließt die geöffnete Schnittstelle
D-70
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07
MOBY E-Library
Bestellbezeichnung Kurzbeschreibung
CCT_READ_N_BLOCK Kartendaten lesen (1 bis n
Datenblöcke; max. 96 Byte)
CCT_WRITE_N_BLOCK Kartendaten schreiben
(1 bis n Datenblöcke; max. 96 Byte)
CCT_WRITE_SIGNAL Digitalen Ausgang ansteuern: reserviert für Umschalten der Antenne
CCT_OFF
CCT_MODE
CCT_OPEN
Antennenfeld ausschalten
Feldbetriebsart des Antennenfeldes einstellen
Logisches Gerät öffnen
Befehlsart
Standard
Standard
Standard
Standard
Standard
Nur für SIM-Betrieb
über RS 232
CCT_CLOSE
CCT_SETKEY
Logisches Gerät schließen Nur für SIM-Betrieb
über RS 232
Kartenlese-/Kartenschreibschnittstelle parametrieren
Optional
CCT_SET_KEY_TEMP Temporären Schlüssel ändern Optional
CCT_GET_FIELD_STATE Aktuelle Kartenindizes abfragen
Optional
CCT_RESET Lesekopf rücksetzen Optional –
Allgemeiner Befehl
Die Befehle der MOBY E-Library sind identisch mit der Standard MOBY E-Lib
“CCTWAPI”. Es sind jedoch nicht alle Befehle der CCTWAPI beim Handterminal vorhanden.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-71
A 05/07
MOBY I-Library (Normaladressierung des MDS)
Funktionsaufruf moby_init moby_read moby_write moby_reset
Kurzbeschreibung
Initialisiert einen MDS von Adresse 0 bis zur
Endadresse mit einem Füllzeichen
Liest einen Datenblock vom MDS
Schreibt einen Datenblock auf den MDS
Reset-Befehl mit Parametrierung zum Lesekopf
übertragen moby_status nMobyIOpen
Statusbefehl zum Lesekopf senden
Schnittstelle öffnen; Lesekopf einschalten vMobyIClose Schließt die geöffnete Schnittstelle; der Lesekopf wird abgeschaltet nMobyIReadStartProtocol Liest das Hochlauftelegramm vom Lesekopf ein
D-72
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418
A 05/07
MOBY I-Library (Filehandler-Adressierung)
Funktionsaufruf wFhRead wFhWrite wFhMdsStatus wFhAttrib wFhDelete wFhCreate wFhFormat wFhDir wFhCover wFhDirInfo nTagTypeFromTable lTagLenFromTable
Fhreset nFhOpenCom vFhCloseCom
Kurzbeschreibung
Lesen einer kompletten Datei vom MDS
Beschreiben einer Datei bzw. Anhängen von
Daten an eine Datei
Statusbefehl zum MDS
File-Attribut setzen
Datei auf dem MDS löschen
Eine neue Datei auf dem MDS anlegen
MDS formatieren
Directory aus dem MDS auslesen
Die MDS-Dateistruktur schützen
Informationen aus der DIR-Struktur in die
DirInfo-Struktur schreiben
Gibt den MDS-Typ aus einer Tabelle zurück
Gibt die MDS-Größe aus einer Tabelle zurück
Filehandler-Reset durchführen
Schnittstelle öffnen; Lesekopf einschalten
Schließt die geöffnete Schnittstelle; der Lesekopf wird abgeschaltet.
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418 D-73
A 05/07
D-74
STG Hand-Held Terminal PRO
(5)J31069-D0126-U001-A6-7418

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Reads and writes to MOBY D/E/I data memories
- Provides service and test functionalities
- Supports custom application programming
- Rugged design for harsh environments
- Easy-to-read display with illumination
- File handling for data storage and transfer
- User-friendly interface with menu navigation