Sony DAV-HDX 587WC DVD Home Theatre System Operating Instructions
Below you will find brief information for DVD Home Theatre System DAV-HDX587WC. This system is designed to play DVD VIDEO, DVD-R/DVD-RW in DVD VIDEO format, DVD+R/DVD+RW in DVD VIDEO format, DVD-R/DVD-RW in VR (Video Recording) mode (except for DVD-R DL), VIDEO CD, Super VCD, CD-R/CD-RW in video CD format or Super VCD format, Super Audio CD, Audio CD, CD-R/CD-RW in audio CD format, DATA CD containing MP3 files and JPEG image files, and conforming to ISO 9660 Level 1/Level 2, or Joliet (extended format), and DATA DVD containing MP3 files and JPEG image files, and conforming to UDF (Universal Disk Format). The system offers features such as 5.1 channel surround sound, HDMI output, DIGITAL MEDIA PORT connection, and S-AIR functionality.
Advertisement
Advertisement
4-122-24011 (1)
DVD Home Theatre
System
Operating Instructions
DAV-HDX587WC
©2009 Sony Corporation
2 US
WARNING
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Caution – The use of optical instruments with this product will increase eye hazard.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
To reduce the risk of fire, do not cover the ventilation opening of the apparatus with newspapers, tablecloths, curtains, etc. Do not place the naked flame sources such as lighted candles on the apparatus.
To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus.
Do not expose batteries or apparatus with batteryinstalled to excessive heat such as sunshine, fire or the like.
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
Indoor use only.
This appliance is classified as a CLASS 1
LASER product. This marking is located on the rear exterior.
Precautions
On power sources
• The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off.
• As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately.
For the customers in the U.S.A.
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Owner’s Record
The model and serial numbers are located on the rear exterior of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.
Model No. DAV-HDX587WC
Serial No.______________
Date of Manufacture Marking is located on the bottom exterior.
The following FCC statement applies only to the version of this model manufactured for sale in the
USA. Other versions may not comply with FCC technical regulations.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna (aerial).
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
ENERGY STAR
®
is a U.S. registered mark.
As an ENERGY STAR
®
partner,
Sony Corporation has determined that this product meets the ENERGY
STAR
®
guidelines for energy efficiency.
For the wireless transceiver
(EZW-RT10/EZW-RT10A)
This equipment must not be co-located or operated in conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in
Supplement C to OET65.
This equipment should be installed and operated with at least 20cm and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and ankles).
Notice for the customers in
Canada
For the wireless transceiver
(EZW-RT10/EZW-RT10A)
This Class B digital apparatus complies with Canadian
ICES-003.
This device complies with RSS-Gen of IC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
This equipment complies with IC radiation exposure limits set forth for uncontrolled equipment and meets
RSS-102 of the IC radio frequency (RF) Exposure rules.
This equipment should be installed and operated with at least 20cm and more between the radiator and persons body (excluding extremities: hands, wrists, feet and ankles).
3 US
4 US
About These Operating
Instructions
• The instructions in these Operating
Instructions describe the controls on the remote. You can also use the controls on the unit if they have the same or similar names as those on the remote.
• The Control Menu items may vary depending on the area.
• “DVD” may be used as a general term for a
DVD VIDEO, DVD+RW/DVD+R, and DVD-
RW/DVD-R.
• Measurements are expressed in feet (ft) for
North American models.
• The default setting is underlined.
Copyrights
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
This system incorporates with Dolby* Digital and Dolby Pro Logic (II) adaptive matrix surround decoder and the DTS** Digital
Surround System.
* Manufactured under license from Dolby
Laboratories.
Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.
** Manufactured under license under U.S. Patent #’s:
5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Surround are registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. © 1996-2008
DTS, Inc. All Rights Reserved.
This system incorporates High-Definition
Multimedia Interface (HDMI TM ) technology.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
“DVD-RW,” “DVD-R,” “DVD+RW,”
“DVD+R,” “DVD VIDEO,” and the “CD” logos are trademarks.
“BRAVIA” is a trademark of Sony Corporation.
“PLAYSTATION” is a trademark of Sony
Computer Entertainment Inc.
“S-AIR” and its logo are trademarks of Sony
Corporation.
About the S-AIR function
The system is compatible with the S-AIR function, which allows transmission of sound between S-AIR products wirelessly.
The following S-AIR products can be used with the system:
• Surround amplifier (optional): You can enjoy surround speaker sound wirelessly.
• S-AIR receiver (supplied): You can enjoy system sound in another room.
The surround amplifier can be purchased as an option (the S-AIR product lineup differs depending on the area).
Notes or instructions for the surround amplifier or S-AIR receiver in these Operating
Instructions refer only to when the surround amplifier or S-AIR receiver is used.
For details on the S-AIR function, see “Using an
5 US
6 US
Table of Contents
About These Operating Instructions ....... 4
About the S-AIR function ....................... 5
Playable Discs......................................... 7
Getting Started
Step 1: Installing the System .......12
Step 2: Connecting the System ...21
Setup ........................................29
Step 4: Selecting the Source .......32
Sound .......................................33
Disc
Playing a Disc ....................................... 36
Using Play Mode................................... 41
Searching/Selecting Disc Contents ....... 44
Playing MP3 Files/JPEG Image Files... 46
Adjusting the Delay Between the Picture and Sound ....................................... 50
Restricting Playback of the Disc........... 50
Changing the System Settings by Using the Setup Display............................ 52
Tuner
Presetting Radio Stations ...................... 60
Listening to the Radio........................... 61
Control for HDMI/External
Audio Device
Using the Control for HDMI Function for
“BRAVIA” Sync ............................ 63
Adapter ........................................... 65
Using an S-AIR Product ....................... 66
Other Operations
Getting Optimal Surround Sound for a
Room .............................................. 71
Calibrating the Appropriate Settings
Automatically ................................. 72
Controlling the TV with the Supplied
Remote ........................................... 73
Using the Sound Effect......................... 74
Selecting the Effect to Suit the Source....................................... 75
Enjoying Multiplex Broadcast Sound .. 75
Changing the Input Level of the Sound from Connected Components......... 76
Using the Sleep Timer .......................... 76
Changing the Brightness of the Front
Panel Display.................................. 77
Viewing Information About the Disc ... 77
Returning to the Default Settings ......... 79
Additional Information
Precautions ........................................... 81
Notes about the Discs ........................... 82
Troubleshooting.................................... 83
Self-diagnosis Function ........................ 89
Specifications ....................................... 90
Glossary ................................................ 92
Playback priority of file types .............. 94
Language Code List.............................. 95
Index to Parts and Control .................... 96
Guide to the Control Menu Display ... 100
Index ................................................... 103
Playable Discs
Type
DVD VIDEO
Disc logo Characteristics
• DVD VIDEO
• DVD-R/DVD-RW in DVD VIDEO format or video mode
• DVD+R/DVD+RW in DVD VIDEO format
Icon
VR (Video
Recording) mode
VIDEO CD
Super Audio CD
• DVD-R/DVD-RW in VR (Video
Recording) mode (except for DVD-R
DL)
• VIDEO CD (Ver. 1.1 and 2.0 discs)
• Super VCD
• CD-R/CD-RW/CD-ROM in video CD format or Super VCD format
• Super Audio CD
CD • Audio CD
• CD-R/CD-RW in audio CD format
DATA CD
DATA DVD
–
–
• CD-R/CD-RW/CD-ROM in DATA CD format, containing MP3 files
1)
and JPEG image files
2)
, and conforming to ISO
9660
3)
Level 1/Level 2, or Joliet
(extended format)
• DVD-ROM/DVD-R/DVD-RW/
DVD+R/DVD+RW in DATA DVD format, containing MP3 files
1)
and JPEG image files
2)
, and conforming to UDF
(Universal Disk Format)
1)
MP3 (MPEG1 Audio Layer 3) is a standard format defined by ISO/MPEG for compresses audio data. MP3 files must be in MPEG1 Audio Layer 3 format.
2)
JPEG image files must conform to the DCF image file format. (DCF “Design rule for Camera File system”: Image standards for digital cameras regulated by Japan Electronics and Information Technology Industries Association
(JEITA).)
3)
A logical format of files and folders on CD-ROMs, defined by ISO (International Organization for
Standardization).
7 US
8 US
Notes on discs
This product is designed to playback discs that conform to the Compact Disc (CD) standard.
DualDiscs and some of the music discs encoded with copyright protection technologies do not conform to the Compact Disc (CD) standard, therefore, these discs may not be playable by this product.
Example of discs that the system cannot play
The system cannot play the following discs:
• CD-ROM/CD-R/CD-RW other than those recorded in the formats listed on page 7
• CD-ROM recorded in PHOTO CD format
• Data part of CD-Extra
• CD Graphics disc
• DVD Audio
• DATA CD/DATA DVD that does not contain MP3 files or JPEG image files
• DVD-RAM
• Blu-ray Disc
Also, the system cannot play the following discs:
• A DVD VIDEO with a different region code (page 9)
• A disc that has a non-standard shape (e.g., card, heart)
• A disc with paper or stickers on it
• A disc that has the adhesive of cellophane tape or a sticker still left on it
Note about CD-R/CD-RW/DVD-R/DVD-RW/DVD+R/DVD+RW
In some cases, CD-R/CD-RW/DVD-R/DVD-RW/DVD+R/DVD+RW cannot be played on this system due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software.
The disc will not play if it has not been correctly finalized. For more information, refer to the operating instructions for the recording device.
Note that some playback functions may not work with some DVD+RWs/DVD+Rs, even if they have been correctly finalized. In this case, view the disc by normal playback. Also some DATA CDs/DATA
DVDs created in Packet Write format cannot be played.
About Multi Session CD
• This system can play a Multi Session CD when an MP3 file is contained in the first session. Any subsequent MP3 files recorded in later sessions can also be played back.
• This system can play a Multi Session CD when a JPEG image file is contained in the first session.
Any subsequent JPEG image files recorded in later sessions can also be played back.
• If MP3 files and JPEG image files in music CD format or video CD format are recorded in the first session, only the first session will be played back.
Region code
Your system has a region code printed on the rear of the unit and will only play a DVD labeled with the same region code.
A DVD VIDEO labeled ALL will also play on this system.
If you try to play any other DVD VIDEO, the message [Playback prohibited by area limitations.] will appear on the TV screen. Depending on the DVD VIDEO, no region code indication may be given even though playing the DVD VIDEO is prohibited by area restrictions.
Note about playback operations of a DVD or VIDEO CD
Some playback operations on a DVD or VIDEO CD may be intentionally set by software producers.
Since this system will play a DVD or VIDEO CD according to the disc contents the software producers designed, some playback features may not be available. Be sure to read the operating instructions supplied with the DVD or VIDEO CD.
9 US
Getting Started
Unpacking
• Front speakers (2)
• Center speaker (1)
• Surround speakers (2)
• Speaker cords (6, red/white/ green/gray/blue/purple)
• Screws (with washer) (4)
• Video cord (1)
• Wireless transceivers (2)
• Remote commander
(remote) (1)
• R6 (size AA) batteries (2)
• Operating Instructions
• Quick Setup Guide
• Setup Disc (DVD)
• DIGITAL MEDIA PORT adapter (TDM-iP20) (1)
• Calibration mic (1)
• Subwoofer (1)
• Foot pads (1 set)
• AM loop antenna (aerial) (1) • Posts (2)
• Bases (2)
• FM wire antenna (aerial) (1) or
• Screws (black) (4)
• Operating Instructions for the DIGITAL MEDIA
PORT adapter (TDM-iP20)
• S-AIR receiver (AIR-SA10)
(1)
• Operating Instructions for the
S-AIR receiver (AIR-SA10)
10 US
Inserting batteries into the remote
Insert two R6 (size AA) batteries (supplied) by matching the 3 and # ends on the batteries to the markings inside the compartment. To use the remote, point it at the remote sensor on the unit.
Note
• Do not leave the remote in an extremely hot or humid place.
• Do not use a new battery with an old one.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight or lighting apparatus. Doing so may cause a malfunction.
• If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.
11 US
Step 1: Installing the System
Positioning the system
For the best possible surround sound, place all speakers at the same distance from the listening position
( A ). The distance can be between 1.0 to 7.0 meters.
If you cannot place the center speaker and surround speakers at the same distance as ( A ), you can move the center speaker up to 1.6 meters closer to the listening position ( B ), and the surround speakers up to 5.0 meters closer to the listening position ( C ).
The subwoofer can be placed anywhere in the room.
Center speaker
Front left speaker (L)
Subwoofer
Front right speaker (R)
B
A
A
A
C
A A
C
Surround left speaker (L) Surround right speaker (R)
Note
• Use caution when placing the speakers and/or speaker stands attached to the speakers on a specially treated (waxed, oiled, polished, etc.) floor, as staining or discoloration may result.
• Do not lean or hang on a speaker, as it may fall down.
12 US
Attaching the foot pads to the subwoofer
Attach the foot pads (supplied) to the bottom of the subwoofer to stabilize the subwoofer and prevent it from slipping.
Remove the foot pads from the protective cover.
,
13 US
Assembling the speakers
Before connecting the speakers, attach the speaker stand to the speaker.
(For the front speakers)
Use the parts as follows:
• Front speakers (2)
• Speaker cords (2, red/white)
• Posts (2)
• Bases (2)
• Screws (black) (4)
• Screws (with washer) (4)
For details of how to connect the speaker cords to the SPEAKER jacks, see page 21.
Note
• Spread a cloth on the floor to avoid damaging the floor when you assemble the speakers.
Tip
• You can use the speaker without the speaker stand by installing it on the wall (page 19).
14 US
1
Insert the post into the hole on the bottom of the speaker so that the screw on the post faces the front of the speaker.
Speaker
,
Screw
Post
2
Adjust the height of the speaker, then secure the post with two screws (with washer).
You can change the height of the speaker depending on the screw positions. Adjust the screw holes of the post to the holes on the rear of the speaker ( A , B , C , or D ). The height of the speaker can be increased by using the holes in order from A to D .
Rear of the speaker
Example: Lowest position
A
B
C
D
Secure two screws (with washer).
Post
15 US
3
Thread the speaker cord through the hole in the base and post.
The connector and color tube of the speaker cords are the same color as the label of the jacks to be connected.
Use the speaker cords as follows:
• Front left speaker (L): White
• Front right speaker (R): Red
Be careful with the orientation of the post. Thread the speaker cord into the end of the post that has two holes.
Post
Bottom of the base Top of the base
Speaker cord
,
,
Base
Rear of the speaker
16 US
4
Connect the speaker cords to the speaker.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with the color tube to 3 , and the speaker cord without the color tube to # .
Color tube
Front left speaker (L): White
Front right speaker (R): Red
Rear of the speaker
5
Attach the post to the base.
Insert the post so that the slot on the lower part of the post aligns with the projection of the base, then secure the post with the two screws (black).
Post
Slot
,
Projection
Base
Screws
(black)
Note
• Make sure that the slot on the post aligns with the projection of the base by rotating the post slightly.
17 US
6
Take up any speaker cord slack.
Take up slack in the speaker cord by pulling from the bottom of the base.
Secure the speaker cord by running it through the slot.
Adjust the length of the cord.
Fully-assembled illustration
Front left speaker (L):
White label
Front right speaker (R):
Red label
White Red
18 US
Installing the speakers on a wall
Caution
• Contact a screw shop or installer for information regarding the wall material or screws to be used.
• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach the screws securely to a beam. Install the speakers on a vertical and flat wall where reinforcement is applied.
• Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength or improper screw installation, natural calamity, etc.
Before installing the speakers on a wall, connect the speaker cord to the speaker.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with the color tube to 3 , and the speaker cord without the color tube to # .
Color tube
Front left speaker (L): White
Front right speaker (R): Red
Center speaker: Green
Surround left speaker (L): Blue
Surround right speaker (R): Gray
1
Prepare screws (not supplied) that are suitable for the hole on the back of each speaker.
See the illustrations below.
4 mm (
5
/
32
inch)
Hole on the back of the speaker
30 mm (1
3
/
16
inches)
(
5 mm
7
/
32
inch)
(
10 mm
13
/
32
inch)
19 US
2
Fasten the screws to the wall.
For the center speaker
145 mm
(5
3
/
4
inches)
For the front speakers
101.6 mm
(4 inches)
(
11
/
32
8 to 10 mm
to
13
/
32
inch)
For the surround speakers
(
11
/
32
8 to 10 mm
to
13
/
32
inch)
(
11
/
32
8 to 10 mm
to
13
/
32
inch)
3
Hang the speakers on the screws.
Hole on the back of the speaker
(
5 mm
7
/
32
inch)
(
10 mm
13
/
32
inch)
Rear of the speaker
20 US
Step 2: Connecting the System
For connecting the system, read the information on the following pages.
Do not connect the AC power cord (mains lead) of the unit to a wall outlet (mains) until all the other connections are made.
Note
• When you connect another component with a volume control, turn down the volume of the other components to a level where sound is not distorted.
Connecting the speakers
The connector of the speaker cords and the color tube are color-coded depending on the type of speaker.
Connect the speaker cords to match the color of the SPEAKER jacks of the unit.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with the color tube to 3 , and the speaker cord without the color tube to # . Do not catch the speaker cord insulation (rubber covering) in the speaker terminals.
To connect speaker cords to the unit
When connecting to the unit, insert the connector until it clicks.
Purple
(Subwoofer)
Red
(Front right speaker (R))
White
(Front left speaker (L))
SPEA
KER
FRONT R
SUR R
FRONT L
HDM
I OUT
SUR L
DMP
ORT
DC5V
0.7A M
AX
TV
DIGITAL IN
OPTICAL
COAXIAL
SPEA
KER
CENTER
SUBW
OOFE
R
Green
(Center speaker)
FM
COAXIAL 75
ANTE
NNA
AM
EZW-R
T10
TV/VIDEO
COM
PONE
NT VI
DEO
OUT
PB/C
B
PR/C
R
Y
VIDEO
OUT
R
AUDIO IN
L
Blue
(Surround left speaker (L))
Gray
(Surround right speaker (R))
To connect speaker cords to the speaker
Connector
(–)
Color tube
(+)
Rear of the speaker
21 US
Connecting the TV (Video connection)
This connection sends a video signal to the TV.
Depending on the jacks on your TV, select the connection method.
C Component video cable
(not supplied)
EZW-
RT10
COM
PONE
NT VI
DEO
OUT
PB/C
B
PR/C R
Y
SPEA
KER
FRONT R
SUR R
FRONT L
HDM
I OUT
SUR L
DMP
ORT
DC5V
AX
0.7A M
TV
DIGITAL IN
OPTICAL
COAXIAL
SPEA
KER
CENTER
SUBW
OOFE
R
B HDMI cable (not supplied)
TV/VIDEO
R
AUDIO IN
L
FM
COAXIAL 75
ANTE
NNA
AM
A Video cord (supplied)
To the HDMI IN jack of the TV.
To the component video input jacks of the TV.
To the video input jack of the TV.
Method 1: Video cord (
A
) connection
This is the basic connection.
Method 2: HDMI
*
cable (
B
) and video cord (
A
) connection
If your TV has an HDMI jack, connect to the TV both with an HDMI cable and video cord. Picture quality will be improved compared to using only the video cord connection.
When connecting with the HDMI cable, you need to select the type of output signal (page 31).
To view images from the DIGITAL MEDIA PORT adapter, you need to connect to the TV with the video cord. Video signals from the DIGITAL MEDIA PORT adapter are not output via the HDMI OUT jack.
* HDMI (High-Definition Multimedia Interface)
Method 3: Component video cable (
C
) and video cord (
A
) connection
If your TV does not have an HDMI jack, but has component video input jacks, connect to the TV both with a component video cable and video cord. Picture quality will be improved compared to using only the video cord connection.
When connecting with the component video cable, you need to set the type of output signal to
To view images from the DIGITAL MEDIA PORT adapter, you need to connect to the TV with the video cord. Video signals from the DIGITAL MEDIA PORT adapter are not output via the
COMPONENT OUT jack.
22 US
Connecting the TV (Audio connection)
This connection sends an audio signal to the unit from the TV. To listen to TV sound via the system, perform this connection.
TV/VIDEO
COM
PONE
DEO
OUT
PR/C
R
Y
VIDEO
OUT
R
AUDIO IN
L
FM
COAXIAL 75
ANTE
NNA
AM
D Audio cord (not supplied)
TV
DIGITAL IN
OPTICAL
COAXIAL
SPEA
KER
CENTER
SUBW
R
E Digital optical cord
(not supplied)
SPEA
KER
FRONT R
SUR R
FRONT L
HDM
I OUT
SUR L
DMP
ORT
DC5V
0.7A M
AX
F Digital coaxial cord (not supplied)
To the audio out jacks of the TV.
To the digital optical out jack of the TV.
To the digital coaxial out jack of the TV.
Method 1: Audio cord (
D
) connection
This is the basic connection and sends an analog audio signal.
Method 2: Digital optical cord (
E
) or digital coaxial cord (
F
) connection
When the TV has a digital optical or coaxial output jack, you can improve sound quality by connecting with a digital optical or coaxial cord in addition to an audio cord connection.
Note
• The system can accept both digital and analog signals. Digital signals have priority over analog signals. (COAXIAL has priority over OPTICAL.) If the digital signal ceases, the analog signal will be processed after 2 seconds.
Tip
• You can connect another component, such as a VCR, digital satellite receiver, or PlayStation, to the TV/VIDEO
(AUDIO IN R/L) jacks or DIGITAL IN OPTICAL/COAXIAL jacks instead of the TV.
23 US
Connecting the other components
You can enjoy connected components via the system’s speakers.
Portable audio source (not supplied): G
DIGITAL MEDIA PORT adapter: H (TDM-iP20 is supplied. You can also use other DIGITAL
MEDIA PORT adapters.)
G Stereo mini-plug cord
(not supplied)
SPEA
KER
CENTER
SUBW
OOFE
R
TV
DIGITAL IN
OPTICAL
COAXIAL
To a portable audio source
SPEA
KER
FRONT R
SUR R
FRONT L
HDM
I OUT
SUR L
DMP
ORT
DC5V
0.7A M
AX
FM
COAXIAL 75
ANTE
NNA
AM
EZW-R
T10
TV/VIDEO
COM
PONE
NT VI
OUT
VIDEO
OUT
R
AUDIO IN
L
Y
PB/C
B
H DIGITAL MEDIA PORT
Note
• Connect the DIGITAL MEDIA PORT adapter so that the V marks are aligned.
When disconnecting, pull out while pressing .
Tip
• You can connect another component, such as a VCR, digital satellite receiver, or PlayStation, to the TV/VIDEO
(AUDIO IN R/L) jacks or DIGITAL IN OPTICAL/COAXIAL jacks instead of the TV.
24 US
If your TV has multiple audio/video inputs
You can enjoy sound with the speakers of the system through the connected TV. Connect the components as follows.
TV
VCR, digital satellite receiver,
PlayStation, etc.
VCR, digital satellite receiver,
PlayStation, etc.
System
:Signal flow
Select the component on the TV. For details, refer to the operating instructions of the TV.
If the TV does not have multiple audio/video inputs, a switcher will be necessary to receive sound from more than one component.
25 US
Connecting the antenna (aerial)
To assemble the AM loop antenna (aerial)
To connect the antenna (aerial)
AM loop antenna (aerial)
(supplied)
FM
COAXIAL 75 or
ANTE
NNA
AM
AM
FM wire antenna (aerial)
(supplied)
Note
• Keep the AM loop antenna (aerial) and cord away from the system or other AV components, as noise may result.
• Be sure to fully extend the FM wire antenna (aerial).
• After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
Tip
• Adjust the direction of the AM loop antenna (aerial) for best AM broadcast sound.
• If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM antenna (aerial) as shown below.
Outdoor FM antenna (aerial)
Unit
ANTENNA
FM
COAXIAL 75
AM
26 US
Inserting the wireless transceiver
You can transmit sound from the unit to an S-AIR product, such as a surround amplifier or S-AIR receiver.
To transmit sound from the unit, you need to insert the wireless transceivers into the unit, surround amplifier, and S-AIR receiver.
For details of S-AIR products, see “Using an S-AIR Product” (page 66).
COM
PONE
NT VI
OUT
Y
PB/C
B
TV/VIDEO
R
AUDIO IN
L
FM
COAXIAL 75
ANTE
NNA
AM
Note
• Also, insert the wireless transceiver into the S-AIR receiver. For details, refer to the operating instructions of the S-AIR receiver.
SPEA
KER
FRONT L
FRONT R
HDM
I OUT
DMP
ORT
DC5V
0.7A M
AX
Wireless transceiver
Note
• When you insert the wireless transceiver, make sure that the AC power cord (mains lead) is not connected to a wall outlet (mains).
• Do not touch the terminals of the wireless transceiver.
• Insert the wireless transceiver so that the V marks are aligned.
• Do not insert anything other than the wireless transceiver into the EZW-RT10 slot.
27 US
Connecting the AC power cords (mains leads)
Before connecting the AC power cord (mains lead) of the unit to a wall outlet (mains), connect all the speakers to the unit.
Wall outlet (mains): The shape of the wall outlet (mains) differs depending on the area.
Also, connect the AC power cord (mains lead) of the S-AIR receiver to a wall outlet (mains).
About the demonstration
After connecting the AC power cord (mains lead), the demonstration appears in the front panel display.
Setting the demonstration mode to on/off
1
Press [ / 1 on the unit.
The system turns on.
2
Press SYSTEM MENU.
3
Press X / x repeatedly until “DEMO” appears in the front panel display, then press or c .
4
Press X / x to select a setting.
• “DEMO ON”: On.
• “DEMO OFF”: Off.
5
Press .
The setting is made.
6
Press SYSTEM MENU.
The system menu turns off.
Tip
• When you purchase the system new, or if the system is at its factory default settings (ex., after performing “COLD
RESET” (page 79)), you can turn off the demonstration simply by pressing
[ / 1 on the remote (except for U.S. models).
28 US
Step 3: Performing the
Quick Setup
Follow the Steps below to make the basic adjustments for using the system.
Displayed items vary depending on the area.
" / 1
5
Press X / x to select a language, then press .
The Setup Display for selecting the aspect ratio of the TV to be connected appears.
VIDEO SETUP
TV TYPE:
PROGRESSIVE
(COMPONENT OUT)
:
16:9
16:9
4:3 OUTPUT:
BLACK LEVEL:
PAUSE MODE:
4:3 LETTER BOX
4:3 PAN SCAN
BLACK LEVEL
(COMPONENT OUT)
: OFF
AUTO
C / X / x / c ,
DISPLAY
1
Turn on the TV.
2
Press [ / 1 .
Note
• Make sure that the function is set to “DVD”
3
Switch the input selector on your TV so that the signal from the system appears on the TV screen.
[Press [ ENTER ] to run QUICK SETUP.] appears at the bottom of the TV screen. If this message does not appear, recall the
Quick Setup display (page 30).
4
Press without inserting a disc.
The Setup Display for selecting the language used in the on-screen display appears.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
FRENCH
SPANISH
PORTUGUESE
6
Press X / x to select the setting that matches your TV type, then press .
• [16:9]: For a wide-screen TV or a 4:3 standard TV with a wide-screen mode
• [4:3 LETTER BOX] or [4:3 PAN SCAN]:
For a 4:3 standard TV (page 54)
The Setup Display for the Control for
HDMI function appears.
HDMI SETUP
HDMI RESOLUTION:
CONTROL FOR HDMI:
VOLUME LIMIT:
YC B C R /RGB(HDMI):
AUDIO(HDMI):
JPEG RESOLUTION:
AUTO (1920x1080p)
ON
ON
OFF
OFF
SD
7
Press X / x to select the setting, then press .
• [ON]: The Control for HDMI function
• [OFF]: The Control for HDMI function is set to off.
The Setup Display for selecting the speaker formation appears.
SPEAKER FORMATION
STANDARD
29 US
8
Press C / c to select the speaker formation image as the speakers are actually positioned, then press .
For details, see “Getting Optimal Surround
9
Connect the calibration mic (supplied) to the A.CAL MIC jack on the front panel.
Set up the calibration mic at ear level using a tripod, etc. (not supplied).
The front of each speaker should face the calibration mic, and there should be no obstruction between the speakers and the calibration mic.
Calibration mic location, such as another room, proper measurement will not be obtained.
• The environment of the room in which the system is installed may affect measurements.
When the measurements differ considerably from the status of the speaker installation, perform the speaker settings manually by
following “Settings for the speakers” (page 57).
11
Unplug the calibration mic, press C / c to select [YES], then press .
Quick Setup is finished. All connections and setup operations are complete.
To quit the Quick Setup
Press DISPLAY in any Step.
To recall the Quick Setup display
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
2
Press DISPLAY while the system is in stop mode.
The Control Menu display appears on the
TV screen.
3
Press X / x to select [SETUP], then press .
The options for [SETUP] appear.
9 4 ( 9 9 )
1 ( 1 )
T 0 : 0 1 : 0 8
DVD VIDEO
CUSTOM
CUSTOM
QUICK
10
Press C / c to select [YES], then press
.
[AUTO CALIBRATION] starts.
Be quiet during the measurement.
Note
• Loud test sounds are output when [AUTO
CALIBRATION] starts. You cannot turn the volume down. Give consideration to children and neighbors.
• Before [AUTO CALIBRATION], install the surround amplifier in the appropriate location. If you install the surround amplifier in an improper
30 US
4
Press X / x to select [QUICK], then press
.
The Quick Setup display appears.
Setting the type of video output to match your TV
Depending on the connection of the TV
(page 22), select the type of video output of the
system.
To select the type of video signal output from the HDMI OUT jack
When you connect the unit and the TV with an
HDMI cable, select the type of video signals output from the HDMI OUT jack.
For details, refer also to the operating instructions supplied with the TV/projector, etc.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
2
Press DISPLAY while the system is in stop mode.
The Control Menu display appears on the
TV screen.
3
Press X / x to select [SETUP], then press .
The options for [SETUP] appear.
4
Press X / x to select [CUSTOM], then press .
The Setup Display appears.
5
Press X / x to select [HDMI SETUP], then press .
The options for [HDMI SETUP] appear.
6
Press X / x to select [HDMI
RESOLUTION], then press .
7
Press X / x to select the desired setting, then press .
• [AUTO (1920 × 1080p)]: The system outputs the optimal video signal for the connected TV.
• [1920 × 1080i]: The system outputs 1920
× 1080i* video signals.
• [1280 × 720p]: The system outputs 1280 ×
720p* video signals.
• [720 × 480p]**: The system outputs 720 ×
480p* video signals.
* i: interlace, p: progressive
** Depending on the area, [720 × 480/576p] may appear.
Does your TV accept progressive signals?
Progressive is a method for displaying TV images which reduces flickering and sharpens the image. To use this method, you need to connect to a TV that accepts progressive signals.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
2
Press DISPLAY while the system is in stop mode.
The Control Menu display appears on the
TV screen.
3
Press X / x to select [SETUP], then press .
The options for [SETUP] appear.
4
Press X / x to select [CUSTOM], then press .
The Setup Display appears.
5
Press X / x to select [VIDEO SETUP], then press .
The options for [VIDEO SETUP] appear.
6
Press X / x to select [PROGRESSIVE
(COMPONENT OUT)], then press .
7
Press X / x to select the desired setting, then press .
[OFF]: The system does not output progressive signals. Select this setting when:
– your TV does not accept progressive signals, or,
– your TV is connected via jacks other than the COMPONENT OUT jacks.
[ON]: The system outputs progressive signals. Select this setting when:
– your TV accepts progressive signals, and,
– the TV is connected via the
COMPONENT OUT jacks.
When you select [ON], the confirmation display appears. Follow the Steps below.
31 US
8
Press C / c to select [START], then press .
The system outputs a progressive signal for
5 seconds. Check that the screen is displayed correctly.
9
Press C / c to select [YES], then press
.
The system outputs a progressive signal.
When you select [NO], the system does not output a progressive signal.
Step 4: Selecting the
Source
You can select the playback source.
FUNCTION
+/–
Press FUNCTION +/– repeatedly until the desired function appears in the front panel display.
Each time you press FUNCTION +/–, the function changes as follows.
“DVD” y “TUNER FM” y “TUNER AM” y “TV/VIDEO” y “DMPORT” y
“AUDIO” y …
Function
“DVD”
“TUNER FM”/
“TUNER AM”
“TV/VIDEO”
“DMPORT”
“AUDIO”
Source
Disc that is played by the system
TV or component that is connected to the TV/
VIDEO jacks on the rear panel
DIGITAL MEDIA PORT
Portable audio source that is connected to the AUDIO
IN jack on the front panel
32 US
Step 5: Enjoying Surround Sound
You can enjoy surround sound simply by selecting one of the system’s pre-programmed decoding modes. They bring the exciting and powerful sound of movie theaters into your home.
SYSTEM MENU
X/x/c ,
Enjoying TV sound with the 5.1 channel surround sound effect
1
Press SYSTEM MENU.
2
Press X / x repeatedly until “DEC. MODE” appears in the front panel display, then press
or c .
3
Press X / x repeatedly until “PRO LOGIC” appears in the front panel display.
4
Press .
The setting is made.
5
Press SYSTEM MENU.
The system menu turns off.
Note
• When TV program sound is monaural, sound is output only from the center speaker.
Selecting surround sound effects based on your listening preference
1
Press SYSTEM MENU.
2
Press X / x repeatedly until “DEC. MODE” appears in the front panel display, then press
or c .
3
Press X / x repeatedly until the surround sound effect you want appears in the front panel display.
See the table below for surround sound effect descriptions.
33 US
4
Press .
The setting is made.
5
Press SYSTEM MENU.
The system menu turns off.
About speaker output
The table below describes the options when you connect all the speakers to the unit and you set
[SPEAKER FORMATION] to [STANDARD] (page 71).
The default setting is “A.F.D. MULTI” (when connecting the headphones to the unit or surround amplifier, the default setting is “HP 2CH”).
Sound from Surround effect
“A.F.D. MULTI”
(AUTO FORMAT
DIRECT MULTI)
Effect
Depending on the source.
“A.F.D. STD”
(AUTO FORMAT
DIRECT STANDARD)
The system discriminates the sound format of the source and presents sound as it was recorded/encoded.
• 2 channel source: The system outputs 2 channel sound from the front and surround speakers by assigning the 2 channel sound to the surround left and right channels.
• Multi-channel source: The system outputs sound from the speakers depending on the number of channels of the source.
“PRO LOGIC”
“PLII MOVIE”
“PLII MUSIC”
“2CH STEREO”
• 2 channel source: The system simulates surround sound from 2 channel sources and outputs sound from all the speakers.
– “PRO LOGIC” performs Dolby Pro Logic decoding.
– “PLII MOVIE” performs Dolby Pro Logic II movie mode decoding.
– “PLII MUSIC” performs Dolby Pro Logic II music mode decoding.
• Multi-channel source: The system outputs sound from the speakers depending on the number of channels of the source.
The system outputs the sound from the front speakers and subwoofer regardless of sound format or number of channels.
Multi-channel surround formats are downmixed to 2 channels.
“HP 2CH”
(HEADPHONE 2
CHANNEL STEREO)
The system outputs the sound from the headphones regardless of sound format or number of channels. Multichannel surround formats are downmixed to 2 channels.
34 US
Sound from Surround effect
“HP VIRTUAL”
(HEADPHONE
VIRTUAL)
Effect
The system outputs the sound from the headphones by adding a surround effect regardless of sound format or number of channels.
To turn the surround effect off
Select “A.F.D. STD,” “2CH STEREO,” or “HP 2CH” for “DEC. MODE.”
Note
• When the bilingual broadcast sound is input, “PRO LOGIC,” “PLII MOVIE,” and “PLII MUSIC” are not effective.
• You cannot select the decoding mode while the system is loading a disc.
• Depending on the input stream, the decoding mode may not be effective.
• When you select “A.F.D. MULTI,” the surround or stereo effect may not be effective. In this case, select “A.F.D.
STD,” “PRO LOGIC,” “PLII MOVIE,” or “PLII MUSIC.”
• When changing the decoding mode while using the S-AIR receiver, sound from the S-AIR receiver may skip.
35 US
Disc
Playing a Disc
Depending on the DVD VIDEO or VIDEO CD, some operations may be different or restricted.
Refer to the operating instructions supplied with your disc.
" / 1 DISC 1-5/indicators
Adjust the volume
4
Press DISC 1-5.
Press the button of the disc number you want.
When no disc is in the disc stocker you select, “NO DISC” appears in the front panel display. Perform next Step while
“*DISC-1* (e.g., 2-5)” flashes.
5
Press Z on the unit to open the disc tray, and place a disc on the tray.
Place one disc on the tray, and then press Z .
36 US
Disc tray
DISC SKIP
Z N FUNCTION
Connect headphones
" / 1
FUNCTION
+/–
MUTING
STEP
/
/
,
/m/
M/
X
VOLUME +/–
./>
H x
1
Turn on your TV.
2
Switch the input selector on the TV to this system.
3
Press " / 1 .
The system turns on.
Unless the system is set to “DVD,” press
FUNCTION +/– to select “DVD.”
With the label side up.
Note
• When you play an 8 cm disc, place it on the inner circle of the tray. Be careful that the disc is not skewed on the inner circle of the tray.
• Do not place more than one disc on the tray.
6
Press H .
The system starts playback (continuous play) of the disc whose DISC indicator is green.
x To load other discs
Press DISC 1-5 (any empty slot) and Z to load the disc.
x To play back other discs
Press DISC SKIP on the remote or DISC 1-
5 on the unit.
7
Adjust the volume by using VOLUME +/
– on the remote or the VOLUME control on the unit.
The volume level appears on the TV screen and in the front panel display.
Note
• When you set the Control for HDMI function to on, the TV that is connected to the system with an HDMI cable can be sync-operated with the system. For
details, see “Using the Control for HDMI Function for “BRAVIA” Sync” (page 63).
Tip
• The DISC 1-5 indicators change their color as follows:
– Green: the disc is selected, or the disc is being played back.
– Off: there is no disc.
– Orange: a disc is loaded in the disc stocker but not selected.
– The indicator turns off if an unplayable disc is inserted.
To turn the system off
Press " / 1 while the system is on. The system enters standby mode.
To save power in standby mode
Press " / 1 while the system is on.
To enter power saving mode, make sure that the system is in the following status.
– “DEMO” is set to “OFF” (page 28).
– [CONTROL FOR HDMI] is set to [OFF]
– “S-AIR STBY” is set to “STBY OFF”
To use the headphones
Connect the headphones to the PHONES jack on the unit. The sound of the system is muted.
You can also connect the headphones to the
PHONES jack on the surround amplifier. (The sound of the system is muted.)
Other operations
To
Stop
Pause X
Resume play after pause X or H
> Go to the next chapter, track, or scene
1)
Press x
Go back to the preceding chapter, track, or scene
1)
Turn off the sound temporarily
.
twice in a second.
When you press .
once, you can go to the beginning of the current chapter, track, or scene.
MUTING.
To cancel, press it again or press VOLUME + to adjust the sound volume.
To
Change a disc while playing another disc
Press
DISC SKIP
Play the desired disc directly
Stop play and remove the disc
DISC 1-5 on the unit.
DISC 1-5 and Z on the unit.
Locate a point quickly by playing a disc in fast forward or fast reverse
(Scan)
1)
Watch frame by frame
(Slow-motion Play)
2)
M / or / m while playing a disc. Each time you press M / or / m during scan, the playback speed changes.
To return to normal speed, press H . Actual speeds may differ with some discs.
M / or / m
3) while the system is in pause mode. Each time you press
M / or / m
3) during Slow-motion Play, the playback speed changes. Two speeds are available. To return to normal playback speed, press H .
Play one frame at a time
(Freeze Frame)
2)4)
STEP to go to the next frame while the system is in pause mode. Press STEP
to go to the preceding frame while the system is in pause mode (DVD VIDEO/
DVD-R/DVD-RW only).
To return to normal playback, press H .
Replay the previous scene (10 seconds before)
5)
(instant replay) during playback.
Briefly fast forward the current scene (30 seconds ahead)
6)
(instant advance) during playback.
1)
Except for JPEG image files.
2)
DVD VIDEO/DVD-R/DVD-RW/VIDEO CD only.
3)
Except for VIDEO CDs.
4)
You cannot search for a still picture on a DVD-VR.
5)
DVD VIDEO/DVD-RW/DVD-R only.
6)
DVD VIDEO/DVD-RW/DVD-R/DVD+RW/
DVD+R only.
Note
• Noise may come from the disc changer when changing discs or turning the system on/off.
37 US
38 US
However, this is just noise produced by the operation of the internal mechanisms and does not indicate a malfunction.
To turn on/off the DISC 1-5 indicators’ illumination
When you do not operate the system for more than 30 minutes, the illumination of the DISC 1-
5 indicators starts automatically. You can turn the illumination on/off.
1
Press SYSTEM MENU.
2
Press X / x repeatedly until “ILLUM
MODE” appears in the front panel display, then press or c .
3
Press X / x to select a setting.
• “ILLUM ON”: On.
• “ILLUM OFF”: Off.
4
Press .
The setting is made.
5
Press SYSTEM MENU.
The system menu turns off.
Displaying multi-angles and subtitles
To change the angles
If various angles (multi-angles) for a scene are recorded on a DVD VIDEO, you can change the viewing angle.
Press ANGLE during playback to select the desired angle.
To display the subtitles
If subtitles are recorded on a disc, you can turn the subtitles on/off during playback. If multilingual subtitles are recorded on the disc, you can change the subtitle language during playback, or turn the subtitles on/off whenever you want.
Press SUBTITLE during playback to select the desired subtitle language.
Changing the sound
When the system is playing a DVD VIDEO recorded in multiple audio formats (PCM,
Dolby Digital, MPEG audio, or DTS), you can change the audio format. If the DVD VIDEO is recorded with multilingual tracks, you can also change the language.
With a VIDEO CD, CD, DATA CD, or DATA
DVD, you can select the sound from the right or left channel and listen to the sound of the selected channel through both the right and left speakers.
You cannot change the sound for a Super Audio
CD.
Press AUDIO repeatedly during playback to select the desired audio signal.
x DVD VIDEO
Depending on the DVD VIDEO, the choice of language varies.
When 4 digits are displayed, they indicate a
language code. See “Language Code List”
(page 95) to confirm which language the code
represents. When the same language is displayed two or more times, the DVD VIDEO is recorded in multiple audio formats.
x DVD-VR
The types of sound tracks recorded on a disc are displayed.
Example:
• [1: MAIN] (main sound)
• [1: SUB] (sub sound)
• [1: MAIN+SUB] (main and sub sound)
• [2: MAIN]
• [2: SUB]
• [2: MAIN+SUB] x VIDEO CD/CD/DATA CD (MP3 file)/DATA
DVD (MP3 file)
• [STEREO]: The standard stereo sound.
• [1/L]: The sound of the left channel
(monaural).
• [2/R]: The sound of the right channel
(monaural).
x Super VCD
• [1:STEREO]: The stereo sound of audio track
1.
• [1:1/L]: The sound of the left channel of audio track 1 (monaural).
• [1:2/R]: The sound of the right channel of audio track 1 (monaural).
• [2:STEREO]: The stereo sound of audio track
2.
• [2:1/L]: The sound of the left channel of audio track 2 (monaural).
• [2:2/R]: The sound of the right channel of audio track 2 (monaural).
Checking the audio signal format
Selecting a playback area for a
Super Audio CD
Some Super Audio CDs consist of a 2 channel playback area and a multi-channel playback area. You can select the playback area you want to listen to.
1
Press DISPLAY while the system is in stop mode.
The Control Menu display appears on the
TV screen.
2
Press X / x to select [MULTI/
2CH], then press .
The options for [MULTI/2CH] appear.
3
Press X / x to select the desired setting and press .
• [MULTI]: You can play the multi-channel playback area.
• [2CH]: You can play the 2 channel playback area.
Note
• When the Super Audio CD does not have a multichannel playback area, you cannot select the playback area.
If you press AUDIO repeatedly during playback, the format of the current audio signal
(PCM, Dolby Digital, DTS, etc.) appears as shown below.
Example:
Dolby Digital 5.1 channel
Surround (L/R)
LFE (Low
Frequency Effect)
Front (L/R) +
Center
1: ENGLISH
DOLBY DIGITAL 3 / 2 .1
L
LS
C
LFE
R
RS
Currently playing program format
Example:
Dolby Digital 3 channel
Front (L/R)
Surround
(Monaural)
1:SPANISH
DOLBY DIGITAL 2 / 1
L
S
R
Currently playing program format
Changing a playback layer for a hybrid Super Audio CD
Some Super Audio CDs consist of a Super
Audio CD layer and a CD layer. You can change the playback layer you want to listen to.
1
Press DISPLAY while the system is in stop mode.
The Control Menu display appears on the
TV screen.
2
Press X / x to select [SUPER
AUDIO CD/CD LAYER], then press .
x When the current layer is the CD layer
[SUPER AUDIO CD] appears.
39 US
40 US x When the current layer is the Super
Audio CD layer
[CD] appears.
3
Press to change the layer.
• [SUPER AUDIO CD]: You can play the
Super Audio CD layer.
When the system is playing a Super Audio
CD layer, “SA-CD” lights up in the front panel display.
• [CD]: You can play the CD layer.
When the system is playing a CD layer,
“CD” lights up in the front panel display.
Note
• Each play mode function works only within the selected layer or playback area.
• When you select a CD layer, you cannot change playback areas.
• Super Audio CD audio signals are not output from the
HDMI OUT jack.
Resuming playback from the point where you stopped the disc
(Resume Play)
Playing a VIDEO CD with PBC functions (Ver. 2.0)
(PBC Playback)
To go back to the menu
Press O RETURN.
Note
• Depending on the VIDEO CD, [Press ENTER] in
Step 3 may appear as [Press SELECT] in the operating instructions supplied with the disc. In this case, press H .
Tip
• To play without using the PBC function, press .
/
> or the number buttons while the system is in stop mode to select a track, then press H or . The system starts playback. You cannot play still pictures such as a menu. To return to PBC playback, press x twice, then press H .
With PBC (Playback Control) functions, you can enjoy simple interactive operations, search functions, and other such operations.
PBC playback allows you to play a VIDEO CD interactively by following the menu on the TV screen.
1
Start playing a VIDEO CD with PBC functions.
The menu for your selection appears.
2
Select the item number you want using the number buttons.
If you make a mistake, press CLEAR to cancel the number.
3
Press .
4
Follow the instructions in the menu for interactive operations.
Refer to the operating instructions supplied with the disc, as the operating procedure may differ depending on the VIDEO CD.
When you stop the disc, the system remembers the point where you pressed x and “RESUME” appears in the front panel display. As long as you do not remove the disc, Resume Play will work even if the system is set to standby mode by pressing " / 1 .
1
While playing a disc, press x to stop playback.
“RESUME” appears in the front panel display.
2
Press H .
The system starts playback from the point where you stopped the disc in Step 1.
Note
• Depending on where you stop the disc, the system may not resume playback from exactly the same point.
• The point where you stopped playing may be cleared when:
– you eject the disc.
– the system enters standby mode (DATA CD/
DATA DVD only).
– you change or reset the settings on the Setup
Display.
– you change the parental control level.
– you change the function by pressing FUNCTION
+/–.
– you disconnect the AC power cord (mains lead).
• For a DVD-VR, VIDEO CD, Super Audio CD, CD,
DATA CD, or DATA DVD, the system remembers the resume playback point for the current disc.
• The resume point is cleared when you select another disc.
• Resume Play does not work during Program Play and
Shuffle Play.
• This function may not work properly with some discs.
Tip
• To play from the beginning of the disc, press x twice, then press H .
To enjoy a disc that you played before with resume playback
(Multi-disc Resume)
This system recalls the point where you stopped the disc the last time it was played and resumes playback from that point the next time you insert the same disc. When the resume playback memory is full, the resume playback point for the earliest disc is deleted.
To activate this function, set [MULTI-DISC
RESUME] in [SYSTEM SETUP] to [ON]. For
details, see “[MULTI-DISC RESUME] (DVD
VIDEO/VIDEO CD only)” (page 57).
Note
• This system stores the resume points in memory for up to 10 discs.
Tip
• To play from the beginning of the disc, press x twice, then press H .
Using Play Mode
Creating your own program
(Program Play)
You can play the contents of a disc in the order you want by arranging the order of the tracks on the disc to create your own program. You can program up to 99 tracks.
Note
• You can program tracks on the current disc only.
1
Press
The Control Menu display appears on the
TV screen.
2
Press X / x to select [PROGRAM], then press .
The options for [PROGRAM] appear.
3
Press X / x to select [SET t
], then press .
Total time of the programmed tracks
PROGRAM
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
– –
– –
– –
– –
– –
– –
– –
0: 00:00
T
– –
01
02
03
04
05
06
Tracks recorded on a disc
4
Press c .
The cursor moves to the track row [T] (in this case, [01]).
PROGRAM
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
– –
– –
– –
– –
– –
– –
– –
0: 00:00
T
– –
01
02
03
04
05
06
41 US
42 US
5
Select the track you want to program.
For example, select track [02].
Press X / x to select [02] under [T], then press .
Selected track
PROGRAM
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
02
– –
– –
– –
– –
– –
– –
0: 03:51
T
– –
01
02
03
04
05
06
Total time of the programmed tracks
6
To program other tracks, repeat Steps
4 to 5.
The programmed tracks are displayed in the selected order.
7
Press H to start Program Play.
Program Play starts.
When the program ends, you can restart the same program again by pressing H .
To return to normal play
Press CLEAR while the display for the program setting is not displayed on the TV screen, or select [OFF] in Step 3. To play the same program again, select [ON] in Step 3 and press
.
To turn off the Control Menu display
Press DISPLAY repeatedly until the Control
Menu display is turned off.
To change or cancel a program
1
Follow Steps 1 to 3 of “Creating your own program.”
2
Press X / x to select the program number of the track you want to change or cancel.
If you want to delete the track from the program, press CLEAR.
3
Follow Step 5 for new programming.
To cancel a program, select [--] under [T], then press .
To cancel all of the tracks in the programmed order
1
Follow Steps 1 to 3 of “Creating your own program.”
2
Press X and select [ALL CLEAR].
3
Press .
Note
• When you press CLEAR to return to normal play,
Shuffle Play and Repeat Play are also canceled.
Playing in random order
(Shuffle Play)
You can play the contents on a disc in random order. Subsequent Shuffle Play may produce a different playing order.
Note
• The same song may be played repeatedly when you are playing MP3 files.
• You can shuffle the tracks on the current disc only.
1
Press DISPLAY during playback.
The Control Menu display appears on the
TV screen.
2
Press X / x to select [SHUFFLE], then press .
The options for [SHUFFLE] appear.
3
Press X / x to select the item to be shuffled.
x VIDEO CD/Super Audio CD/CD
• [OFF]: Off.
• [TRACK]: You can shuffle tracks on the disc.
x During Program Play
• [OFF]: Off.
• [ON]: You can shuffle tracks selected in
Program Play.
x DATA CD/DATA DVD
• [OFF]: Off.
• [ON (MUSIC)]: You can shuffle MP3 files in the folder on the current disc.
When no folder is selected, the first folder will play in random order.
4
Press .
Shuffle Play starts.
To return to normal play
Press CLEAR, or select [OFF] in Step 3.
To turn off the Control Menu display
Press DISPLAY repeatedly until the Control
Menu display is turned off.
Note
• You cannot use Shuffle Play with a VIDEO CD or
Super VCD with PBC playback.
• When you press CLEAR to return to normal play,
Program Play and Repeat Play are also canceled.
Playing repeatedly
(Repeat Play)
You can play the contents on a disc repeatedly.
You can use a combination of Shuffle Play or
Program Play modes.
1
Press DISPLAY during playback.
The Control Menu display appears on the
TV screen.
2
Press X / x to select [REPEAT], then press .
The options for [REPEAT] appear.
3
Press X / x to select the item to be repeated.
x DVD VIDEO/DVD-VR
• [OFF]: Off.
• [ALL DISCS]: You can repeat all of the discs.
• [ONE DISC]: You can repeat all of the titles on the current disc. (When the system is playing a DVD-VR, you can repeat all of the titles of the selected disc.)
• [TITLE]: You can repeat the current title on a disc.
• [CHAPTER]: You can repeat the current chapter on a disc.
x VIDEO CD/Super Audio CD/CD
• [OFF]: Off.
• [ALL DISCS]: You can repeat all of the discs.
• [ONE DISC]: You can repeat all of the tracks on the current disc.
• [TRACK]: You can repeat the current track.
x DATA CD/DATA DVD
• [OFF]: Off.
• [ALL DISCS]: You can repeat all of the discs.
• [ONE DISC]: You can repeat all of the folders on the current disc.
• [FOLDER]: You can repeat the current folder.
• [TRACK] (MP3 files only): You can repeat the current file.
4
Press .
The item is selected.
To return to normal play
Press CLEAR, or select [OFF] in Step 3.
To turn off the Control Menu display
Press DISPLAY repeatedly until the Control
Menu display is turned off.
Note
• You cannot use Repeat Play with a VIDEO CD or
Super VCD with PBC playback.
• When the system is playing a DATA CD/DATA
DVD which contains MP3 files and JPEG image files, and their playing time is not the same, the audio sound will not match the image.
• When you press CLEAR to return to normal play,
Program Play and Shuffle Play are also canceled.
43 US
44 US
Searching/Selecting
Disc Contents
Using the DVD’s menu
Selecting an original title or edited title on a DVD-VR
A DVD is divided into many sections, which make up a picture or music feature. These sections are called “titles.” When you play a
DVD which contains several titles, you can select the title you want using DVD TOP
MENU.
When you play a DVD that allows you to select items such as the language for the subtitles and the language for the sound, select these items using DVD MENU.
1
Press DVD TOP MENU or DVD MENU.
The disc’s menu appears on the TV screen.
The contents of the menu vary depending on the disc.
2
Press C / X / x / c or the number buttons to select the item you want to play or change.
3
Press .
To display the DVD’s menu on the
Control Menu display
1
Press DISPLAY during playback.
The Control Menu display appears on the
TV screen.
2
Press X / x to select [DISC
MENU], then press .
The options for [DISC MENU] appear.
3
Press X / x to select [MENU] or [TOP
MENU].
4
Press .
To turn off the Control Menu display
Press DISPLAY repeatedly until the Control
Menu display is turned off.
This function is only available for DVD-VRs with a playlist created.
1
Press DISPLAY while the system is in stop mode.
The Control Menu display appears on the
TV screen.
2
Press X / x to select [ORIGINAL/
PLAY LIST], then press .
The options for [ORIGINAL/PLAY LIST] appear.
3
Press X / x to select a setting.
• [PLAY LIST]: You can play the titles in the order of the existing playlist.
• [ORIGINAL]: You can play the titles originally recorded.
4
Press .
Searching for a title/chapter/ track/scene, etc.
You can search a DVD VIDEO/DVD-VR by title or chapter, and you can search a VIDEO
CD/Super Audio CD/CD/DATA CD/DATA
DVD by track, index, or scene. For a DATA CD/
DATA DVD, you can search by folder or file.
As titles and tracks are assigned unique numbers on the disc, you can select the desired title or track by entering its number. Or, you can search for a scene using the time code.
1
Press DISPLAY. (If [MEDIA] is set to
[MUSIC/PHOTO], press DISPLAY twice.)
The Control Menu display appears on the
TV screen.
2
Press X / x to select the search method.
[** (**)] is selected (** refers to a number).
The number in parentheses indicates the total number of titles, chapters, tracks, indexes, scenes, folders, or files.
9 8 ( 9 9 )
1 3 ( 9 9 )
T 0 : 0 3 : 1 7
DVD VIDEO
For example, to find a scene at 2 hours, 10 minutes, and 20 seconds after the beginning: press 2, 1, 0, 2, 0 ([2:10:20]).
4
Press .
Note
• You cannot search for a scene on a DVD+RW using the time code.
Selected row
3
Press .
[** (**)] changes to [– – (**)].
9 8 ( 9 9 )
1 3 ( 9 9 )
T 0 : 0 3 : 1 7
DVD VIDEO
4
Press X / x or the number buttons to select the desired number of the title, chapter, track, index, scene, etc.
If you make a mistake, press CLEAR to cancel the number.
5
Press .
The system starts playback from the selected number.
Tip
• When the Control Menu display is turned off, you can search for a chapter (DVD VIDEO/DVD-R/DVD-
RW) or track (VIDEO CD/Super Audio CD/CD) by pressing the number buttons and .
To search for a scene using the time code
1
In Step 2, select [TIME].
[T **:**:**] (playing time of the current title) is selected.
2
Press .
[T **:**:**] changes to [T --:--:--].
3
Input the time code using the number buttons.
45 US
46 US
Playing MP3 Files/JPEG
Image Files
You can play MP3 files or JPEG image files:
– which have the extension “.mp3” (MP3 file) or “.jpg”/“.jpeg” (JPEG image file).
– which conform to the DCF* image file format.
* “Design rule for Camera File system”: Image standards for digital cameras regulated by Japan
Electronics and Information Technology Industries
Association (JEITA).
Note
• The system will play any files with the extension
“.mp3,” “.jpg,” or “.jpeg” even if they are not in MP3 or JPEG format. Playing these files may generate a loud noise which could damage your speaker system.
• The system does not play back audio in MP3PRO format.
• The system can recognize up to 200 folders, and will not play any folders beyond the 200th. (Depending on the folder configuration, the number of folders that can be recognized by the system may decrease.)
• The system can recognize up to 150 MP3 files/JPEG image files in a folder.
• The system may take a longer time to play files when progressing to the following folder or jumping to other folders.
• The system may not play certain types of JPEG image files (ex. a JPEG image file that is less than 8 (width)
× 8 (height)).
Selecting an MP3 file or folder
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
2
Load a DATA CD or DATA DVD.
After loading the disc, the list of folders appears on the TV screen.
3
Press
The Control Menu display appears on the
TV screen.
4
Press X / x to select [MEDIA], then press .
The options for [MEDIA] appear.
5
When [MUSIC] is selected, press DVD
MENU. When other than [MUSIC] is selected, press X / x to select [MUSIC], then press .
A list of folders that contain MP3 files appears.
The selected folder is highlighted in yellow.
FOLDER LIST
01 Let's Talk About Love (1985)
02 1st Album (1986)
03 In the Middle of Nowhere (1986)
04 Ready for Romance (1986)
05 In the Garden of Venus (1987)
06 Romantic Warriors (1987)
07 Back for Good (1988)
08 Alone (1999)
6
Press X / x to select a folder.
x To play MP3 files in a folder
Press H to start playing the selected folder.
x To select an MP3 file
Press .
The list of files contained in the folder appears.
TRACK LIST
03 In the Middle of Nowher...
01_Geronimo_s_Cadillac
02_Riding_On_A_White_Swan
03_Give_Me_Peace_On_Earth
04_Sweet_Little_Shella
05_Ten_Thousand_Lonely_Drums
06_Lonely_Tears_In_Chinatown
07_In_Shaire
Press X / x to select a file and press .
The system starts playing the selected file.
You can turn the file list off by pressing
DVD MENU. Pressing DVD MENU again will display the folder list.
To go to the next or previous page
Press / .
To stop playback
Press x .
To play the next or previous MP3 file
Press > to play the next MP3 file. Press .
twice to play the previous MP3 file.
When you press .
once, you can go to the beginning of the current MP3 file.
Note that you can select the next folder by continuing to press > after the last file on the current folder, but that you cannot return to the previous folder by pressing .
. To return to the previous folder, select the folder from the folder list.
To return to the previous display
Press O RETURN.
To turn on/off the display
Press DVD MENU.
Other operations
See “Other operations” (page 37).
Selecting a JPEG image file or folder
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
2
Load a DATA CD or DATA DVD.
After loading the disc, the list of folders appears on the TV screen.
3
Press
The Control Menu display appears on the
TV screen.
4
Press X / x to select [MEDIA], then press .
The options for [MEDIA] appear.
5
When [PHOTO] is selected, press DVD
MENU. When other than [PHOTO] is selected, press X / x to select [PHOTO], then press .
A list of folders that contain JPEG files appears.
The selected folder is highlighted in yellow.
FOLDER LIST
01 Happy birthday
02 Travelling 01
03 2003.08.20
04 Flowers
05 Travelling 02
06 Animals
07 2003.11.16
08 2003.12.03
6
Press X / x to select a folder.
x To go to the next or previous page
Press / .
x To play JPEG image files in a folder
Press H to start playing the selected folder.
The JPEG images are played as a slide show. You can change the interval of the
slide show (page 48), and add effects to the
x To select a JPEG image file by displaying the image browser
Press PICTURE NAVI.
Previews of JPEG image files in the folder appear in 16 subscreens.
1 2 3 4
5
9
6
10
7
11
8
12
13 14 15 16
Press C / X / x / c to select the JPEG image file you want to view, then press .
To return to the previous screen, press O
RETURN.
To play the next or previous JPEG image file
Press c / C when the Control Menu display is not displayed. Note that you can select the next folder by continuing to press c after the last image on the current folder, but that you cannot return to the previous folder by pressing C . To return to the previous folder, select the folder from the folder list.
47 US
48 US
To rotate a JPEG image file
When a JPEG image file is displayed on the TV screen, you can rotate the JPEG image file in 90 degree increments.
Press X / x while viewing a JPEG image file.
Press CLEAR to return to normal view.
Note
• You cannot rotate the JPEG image file when you set
[JPEG RESOLUTION] in [HDMI SETUP] to [(1920
× 1080i) HD ] or [(1920 ×
To stop playback
Press x .
To turn on/off the display
Press DVD MENU.
Other operations
See “Other operations” (page 37).
Playing a slide show with sound
You can play a slide show with sound by first placing both MP3 files and JPEG image files in the same folder on a DATA CD or DATA DVD.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
2
Load a DATA CD or DATA DVD.
After loading the disc, the list of folders appears on the TV screen.
3
Press
The Control Menu display appears on the
TV screen.
4
Press X / x to select [MEDIA], then press .
The options for [MEDIA] appear.
5
When [MUSIC/PHOTO] is selected, press DVD MENU. When other than
[MUSIC/PHOTO] is selected, press X / x to select [MUSIC/PHOTO], then press
.
The list of folders appears.
6
Press X / x to select the desired folder and press H .
The system starts playing the selected folder.
You can turn the folder list on/off by pressing DVD MENU repeatedly.
Note
• If you play a large MP3 file and JPEG image file at the same time, the sound may skip. Sony recommends that you set the MP3 bit rate to 128 kbps or lower when creating the file. If the sound still skips, reduce the size of the JPEG image file.
Selecting the slide show duration of JPEG image files
1
Press DISPLAY. (If [MEDIA] is set to
[MUSIC/PHOTO], press DISPLAY twice.)
The Control Menu display appears on the
TV screen.
2
Press X / x to select [INTERVAL], then press .
The options for [INTERVAL] appear.
3
Press X / x to select a setting.
• [NORMAL]: You can set to the standard duration.
• [FAST]: You can set the duration shorter than [NORMAL].
• [SLOW 1]: You can set the duration longer than [NORMAL].
• [SLOW 2]: You can set the duration longer than [SLOW 1].
4
Press .
Note
• Some JPEG image files may take longer to display than the option you selected. Especially progressive
JPEG image files or JPEG image files of 3,000,000 pixels or more.
Selecting an effect for JPEG image files in the slide show
1
Press DISPLAY. (If [MEDIA] is set to
[MUSIC/PHOTO], press DISPLAY twice.)
The Control Menu display appears on the
TV screen.
2
Press X / x to select [EFFECT], then press .
The options for [EFFECT] appear.
3
Press X / x to select a setting.
• [MODE 1]: The JPEG image file sweeps in from top to bottom.
• [MODE 2]: The JPEG image file stretches out from left to right of the TV screen.
• [MODE 3]: The JPEG image file stretches out from the center of the TV screen.
• [MODE 4]: The JPEG image files randomly cycle through the effects.
• [MODE 5]: The next JPEG image file slides over the previous image.
• [OFF]: Off.
4
Press .
Note
• The [EFFECT] setting is not effective when you set
[JPEG RESOLUTION] in [HDMI SETUP] to [(1920
× 1080i) HD ] or [(1920 ×
Selecting playback priority of the file type
You can select playback priority when mixed media (MP3 files or JPEG image files) are in the disc.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
2
Load a DATA CD or DATA DVD.
After loading the disc, the list of folders appears on the TV screen.
3
Press
The Control Menu display appears on the
TV screen.
4
Press X / x to select [MEDIA], then press .
The options for [MEDIA] appear.
5
Press X / x to select a setting.
• [MUSIC/PHOTO]: You can play both
JPEG image files and MP3 files in the same folder as a slide show.
• [MUSIC]: MP3 file playback has priority.
• [PHOTO]: JPEG image file playback has priority. You can play JPEG image files as a slide show.
6
Press .
For details of the playback priority of file types under the [MEDIA] setting, see
“Playback priority of file types” (page 94).
Displaying a list of MP3 files/
JPEG image files
1
Press DISPLAY during playback.
The Control Menu display appears on the
TV screen.
2
Press X / x to select
[BROWSING], then press .
The options for [BROWSING] appear.
3
Press X / x to select the desired list, then press .
• [FOLDER LIST]: The list of folders
appears. Follow Step 6 of “Selecting an
MP3 file or folder” (page 46) or
“Selecting a JPEG image file or folder”
• [PICTURE LIST] (JPEG image files only): Previews of JPEG image files in the folder appear in 16 subscreens. Follow
Step 6 of “Selecting a JPEG image file or folder” (page 47).
49 US
50 US
Adjusting the Delay
Between the Picture and
Sound
[A/V SYNC]
When the sound does not match the pictures on the TV screen, you can adjust the delay between the picture and sound.
1
Press
The Control Menu display appears on the
TV screen.
2
Press X / x to select [A/V SYNC], then press .
The options for [A/V SYNC] appear.
3
Press X / x to select a setting.
• [OFF]: Off.
• [ON]: You can adjust the delay between picture and sound.
4
Press .
Note
• Depending on the input stream, [A/V SYNC] may not be effective.
Restricting Playback of the Disc
[PARENTAL CONTROL]
The [PARENTAL CONTROL] function allows you to restrict playback of DVDs that have ratings. Scenes may be blocked or replaced with different scenes.
You can set the playback restriction by registering a password. When you set the
[PARENTAL CONTROL] function to on, you need to enter the password to play restricted discs.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
2
Press DISPLAY while the system is in stop mode.
The Control Menu display appears on the
TV screen.
3
Press X / x to select [SETUP], then press .
The options for [SETUP] appear.
4
Press X / x to select [CUSTOM], then press .
The Setup Display appears.
5
Press X / x to select [SYSTEM SETUP], then press .
The options for [SYSTEM SETUP] appear.
6
Press X / x to select [PARENTAL
CONTROL t ], then press .
x If you have not entered a password
The display for registering a new password appears.
PARENTAL CONTROL
Enter a new 4-digit password, then press .
Enter a 4-digit password using the number buttons, then press .
The display for confirming the password appears.
x When you have already registered a password
The display for entering the password appears.
7
Enter or re-enter your 4-digit password using the number buttons, then press
.
The display for setting the playback limitation level appears.
PARENTAL CONTROL
LEVEL:
STANDARD:
CHANGE PASSWORD:
OFF
USA
To turn off the [PARENTAL
CONTROL] function
Set [LEVEL] to [OFF] in Step 11.
To play a disc for which
[PARENTAL CONTROL] is set
1
Load the disc and press H .
The display for entering your password appears.
2
Enter your 4-digit password using the number buttons, then press .
The system starts playback.
Tip
• If you forget your password, remove the disc and
repeat Steps 1 to 6 of “Restricting Playback of the
Disc” (page 50). When you are asked to enter your
password, enter “199703” using the number buttons, then press . The display will ask you to enter a new
4-digit password. After you enter a new 4-digit password, replace the disc in the unit and press H .
When the display for entering your password appears, enter your new password.
8
Press X / x to select [STANDARD], then press .
The selection items for [STANDARD] are displayed.
9
Press X / x to select a geographic area as the playback limitation level, then press .
The area is selected.
When you select [OTHERS t ], select and
enter a standard code from “Parental
Control Area Code List” (page 95) using
the number buttons.
10
Press X / x to select [LEVEL], then press
.
The selection items for [LEVEL] are displayed.
11
Press X / x to select the desired level, then press .
[PARENTAL CONTROL] setting is complete.
The lower the value, the stricter the limitation.
Changing the password
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
2
Press DISPLAY while the system is in stop mode.
The Control Menu display appears on the
TV screen.
3
Press X / x to select [SETUP], then press .
The options for [SETUP] appear.
4
Press X / x to select [CUSTOM], then press .
The Setup Display appears.
5
Press X / x to select [SYSTEM SETUP], then press .
The options for [SYSTEM SETUP] appear.
6
Press X / x to select [PARENTAL
CONTROL t ], then press .
The display for entering the password appears.
51 US
52 US
7
Enter your 4-digit password using the number buttons, then press .
8
Press X / x to select [CHANGE
PASSWORD t ], then press .
9
Enter a new 4-digit password using the number buttons, then press .
10
To confirm your password, re-enter it using the number buttons, then press
.
If you make a mistake entering your password
Press C before you press , then input the correct number.
Changing the System
Settings by Using the
Setup Display
You can make various adjustments to items such as picture and sound.
Displayed items vary depending on the area.
Note
• Playback settings stored in the disc take priority over the Setup Display settings and not all the functions described may work.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
2
Press DISPLAY while the system is in stop mode.
The Control Menu display appears on the
TV screen.
3
Press X / x to select [SETUP], then press .
The options for [SETUP] appear.
4
Press X / x to select [CUSTOM], then press .
The Setup Display appears.
5
Press X / x to select the setup item, then press .
Example: [VIDEO SETUP]
Selected item
VIDEO SETUP
TV TYPE:
PROGRESSIVE
(COMPONENT OUT)
:
4:3 OUTPUT:
BLACK LEVEL:
BLACK LEVEL
(COMPONENT OUT)
:
PAUSE MODE:
16:9
OFF
FULL
ON
OFF
AUTO
Setup items
6
Press X / x to select an item, then press
.
The options for the selected item appear.
Example: [TV TYPE]
VIDEO SETUP
TV TYPE:
PROGRESSIVE (COMPONENT OUT) :
16:9
4:3 OUTPUT:
BLACK LEVEL:
PAUSE MODE:
4:3 LETTER BOX
4:3 PAN SCAN
BLACK LEVEL (COMPONENT OUT) : OFF
AUTO
Options
7
Press X / x to select a setting, then press .
The setting is selected and setup is complete.
Example: [4:3 LETTER BOX]
VIDEO SETUP
TV TYPE: 4:3 LETTER BOX
PROGRESSIVE
(COMPONENT OUT)
: OFF
4:3 OUTPUT:
BLACK LEVEL:
FULL
ON
BLACK LEVEL (COMPONENT OUT) :
PAUSE MODE:
OFF
AUTO
Selected setting
To reset all of the [SETUP] settings
To reset all of the [SETUP] settings, see
“Returning the [SETUP] settings to the default”
x [OSD] (On-Screen Display)
You can switch the display language on the TV screen.
x [MENU] (DVD VIDEO only)
You can switch the language for the disc’s menu.
x [AUDIO] (DVD VIDEO only)
You can switch the language of the sound track.
When you select [ORIGINAL], the language given priority on the disc is selected.
x [SUBTITLE] (DVD VIDEO only)
You can switch the language of the subtitles recorded on the DVD VIDEO.
When you select [AUDIO FOLLOW], the language for the subtitles changes according to the language you selected for the sound track.
Note
• When you select a language in [MENU], [AUDIO], or [SUBTITLE] that is not recorded on the DVD
VIDEO, one of the recorded languages will be automatically selected (depending on the disc, the language may not be selected automatically).
Tip
• If you select [OTHERS t ] in [MENU], [AUDIO], and [SUBTITLE], select and enter a language code
from “Language Code List” (page 95) using the
number buttons.
Setting the display or sound track language
[LANGUAGE SETUP]
Set various languages for the on-screen display or sound track.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
ORIGINAL
AUDIO FOLLOW
Settings for the display
[VIDEO SETUP]
Select settings according to the TV to be connected.
VIDEO SETUP
TV TYPE:
PROGRESSIVE
(COMPONENT OUT)
:
4:3 OUTPUT:
BLACK LEVEL:
BLACK LEVEL (COMPONENT OUT) :
PAUSE MODE:
16:9
OFF
FULL
ON
OFF
AUTO
53 US
x [TV TYPE]
You can select the aspect ratio of the connected
TV.
[16:9]: Select this when you connect a widescreen TV or a TV with a wide mode function.
[4:3 LETTER BOX]: Select this when you connect a 4:3 standard TV. The system displays a wide picture with bands on the upper and lower portions of the TV screen.
[4:3 PAN SCAN]: Select this when you connect a 4:3 standard TV. The system automatically displays a wide picture on the entire screen and cuts off the portions that do not fit.
The system outputs a progressive signal for
5 seconds. Check that the screen is displayed correctly.
3
Press C / c to select [YES], then press
.
The system outputs a progressive signal. If you select [NO], the system will not output a progressive signal.
Note
• [PROGRESSIVE (COMPONENT OUT)] is effective only when you connect the unit and TV with
a component video cable (page 22).
x [4:3 OUTPUT]
When you use a 16:9 aspect ratio TV, you can adjust the aspect ratio to watch 4:3 aspect ratio signals. If you can change the aspect ratio on your TV, change the setting on your TV, not the system.
[FULL]: Select this when you can change the aspect ratio on your TV.
[NORMAL]: Select this when you cannot change the aspect ratio on your TV. A 16:9 aspect ratio signal with black bands on left and right sides of the image appears.
54 US
Note
• Depending on the DVD, [4:3 LETTER BOX] may be selected automatically instead of [4:3 PAN SCAN] or vice versa.
x [PROGRESSIVE (COMPONENT OUT)]
You can set the progressive signal that is output from the COMPONENT OUT jacks to on/off.
For details, see “Does your TV accept progressive signals?” (page 31).
[OFF]: The system outputs interlace signals.
[ON]: The system outputs progressive signals.
When you select [ON], follow the Steps below.
1
Select [ON], then press .
The confirmation display appears.
2
Press C / c to select [START], then press .
16:9 aspect ratio TV
Note
• [4:3 OUTPUT] is effective only when you set [TV
TYPE] in [VIDEO SETUP] to [16:9].
x [BLACK LEVEL]
You can select the black level (setup level) for the video signals output from the jacks other than COMPONENT OUT/HDMI OUT.
[ON]: The standard level.
[OFF]: You can lower the standard black level.
Use this when the picture becomes too white.
x [BLACK LEVEL (COMPONENT OUT)]
You can select the black level (setup level) for the video signals output from the
COMPONENT OUT jacks.
You cannot select this and the setting is not effective when the system outputs a progressive signal.
[OFF]: You can set the black level of the output signal to the standard level.
[ON]: You can raise the standard black level.
Use this when the picture becomes too black.
x [PAUSE MODE] (DVD VIDEO/DVD-R/
DVD-RW only)
You can select the picture in pause mode.
[AUTO]: The picture, including subjects that move dynamically, is output with no jitter. This setting is for normal usage.
[FRAME]: The picture, including subjects that do not move dynamically, is output in high resolution.
Settings for HDMI
[HDMI SETUP]
HDMI SETUP
HDMI RESOLUTION:
CONTROL FOR HDMI:
VOLUME LIMIT:
YC B C R /RGB(HDMI):
AUDIO(HDMI):
JPEG RESOLUTION:
AUTO (1920x1080p)
ON
LEVEL2
YC B C R
OFF
SD x [HDMI RESOLUTION]
You can select the type of video signal that is output from the HDMI OUT jack. For details,
see “To select the type of video signal output from the HDMI OUT jack” (page 31).
[AUTO (1920 × 1080p)]: The system outputs the optimal video signal for the connected TV.
[1920 × 1080i]: The system outputs 1920 ×
1080i* video signals.
[1280 × 720p]: The system outputs 1280 ×
720p* video signals.
[720 × 480p]**: The system outputs 720 ×
480p* video signals.
* i: interlace, p: progressive
** Depending on the area, [720 × 480/576p] may appear.
x [CONTROL FOR HDMI]
You can set the [CONTROL FOR HDMI] function to on/off. This function is available when you connect the system and TV with an
HDMI cable. For details, see “Using the Control for HDMI Function for “BRAVIA” Sync”
[ON]: On. You can operate mutually between components that are connected with an HDMI cable.
[OFF]: Off.
x [VOLUME LIMIT]
If you change the output method of the TV to the system speakers via the TV menu (or by pressing THEATER), the System Audio Control
(page 64) is activated and loud sound may be
output depending on the volume level of the system. You can prevent this by limiting the maximum level of the volume.
[LEVEL3]: Maximum volume level is set to 10.
[LEVEL2]: Maximum volume level is set to 15.
[LEVEL1]: Maximum volume level is set to 20.
[OFF]: Off.
Note
• This function is available only when [CONTROL
FOR HDMI] is set to [ON].
x [YC
B
C
R
/RGB (HDMI)]
You can select the type of HDMI signal output from the HDMI OUT jack.
[YC
B
C
R
]: The system outputs YC
B
C
R
signals.
[RGB]: The system outputs RGB signals.
Note
• If the playback picture becomes distorted, set
[YC
B
C
R
] to [RGB].
• If the HDMI OUT jack is connected to a component with a DVI jack, [RGB] signals will be automatically output even when you select [YC
B
C
R
].
x [AUDIO (HDMI)]
You can select the audio output status from the
HDMI OUT jack.
55 US
56 US
[OFF]: The system does not output sound from the HDMI OUT jack.
[ON]: The system outputs audio signals by converting Dolby Digital, DTS, or 96 kHz/24bit PCM signals to 48 kHz/16-bit PCM.
Note
• When you connect the unit and TV with an HDMI cable and [ON] is selected, [AUDIO DRC], [A/V
SYNC], DYNAMIC BASS, “DEC. MODE,” and sound mode are not applied to the sound that is output from the TV.
• When you set the function to other than “DVD,” the system does not output the sound from the HDMI
OUT jack even if you set [AUDIO (HDMI)] to [ON].
x [JPEG RESOLUTION]
You can select the resolution of JPEG image files output from the HDMI OUT jack.
[SD ]: The system outputs standard resolution with a black frame.
[HD ]: The system outputs HD resolution with a black frame.
[HD]: The system outputs the HD resolution without a black frame.
[(1920 × 1080i) HD ]: The system outputs full size HD resolution with a black frame.
[(1920 × 1080i) HD]: The system outputs full size HD resolution without a black frame.
Note
• [JPEG RESOLUTION] is effective only when you set [TV TYPE] in [VIDEO SETUP] to [16:9], and you set [HDMI RESOLUTION] in [HDMI SETUP] to other than [720 × 480p] or [720 × 480/576p].
• You can select [(1920 × 1080i) HD ] or [(1920 ×
1080i) HD] only when you set [HDMI
RESOLUTION] in [HDMI SETUP] to [1920 ×
1080i].
• The HDMI signal will stop momentarily when:
– the system is loading or unloading a DATA CD or
DATA DVD.
– you change the disc from a DATA CD or DATA
DVD.
– you play a DATA CD or DATA DVD to the end and the system stops playback automatically.
Settings for the audio
[AUDIO SETUP]
AUDIO SETUP
SPEAKER FORMATION:
AUTO CALIBRATION:
AUDIO DRC:
TRACK SELECTION:
OFF
OFF x [SPEAKER FORMATION]
You can select the position of the speakers for
better surround sound. For details, see “Getting
Optimal Surround Sound for a Room”
x [AUTO CALIBRATION]
You can calibrate the appropriate settings
automatically. For details, see “Calibrating the
Appropriate Settings Automatically” (page 72).
x [AUDIO DRC] (DVD VIDEO only)
You can compress the dynamic range of the sound track. [AUDIO DRC] is useful for watching movies at low volume late at night.
[OFF]: No compression of dynamic range.
[STANDARD]: The system reproduces the sound track with the kind of dynamic range that the recording engineer intended.
[MAX]: The system compresses dynamic range fully.
Note
• [AUDIO DRC] works only for Dolby Digital.
x [TRACK SELECTION] (DVD VIDEO only)
You can give the sound track which contains the highest number of channels priority when you play a DVD VIDEO on which multiple audio formats (PCM, DTS, Dolby Digital, or MPEG audio) are recorded.
[OFF]: Off.
[AUTO]: The system selects the sound track automatically according to the priority.
Note
• When you set the item to [AUTO], the language may change. The [TRACK SELECTION] setting has higher priority than the [AUDIO] settings in
[LANGUAGE SETUP] (page 53). (Depending on
the disc, this function may not work.)
• If PCM, DTS, Dolby Digital sound, and MPEG audio have the same number of channels, the system selects
PCM, DTS, Dolby Digital sound, and MPEG audio in this order.
Other Settings
[SYSTEM SETUP]
SYSTEM SETUP
SCREEN SAVER:
BACKGROUND:
PARENTAL CONTROL:
MULTI-DISC RESUME:
RESET:
ON
JACKET PICTURE
ON x [PARENTAL CONTROL]
You can set the playback restrictions. For
details, see “Restricting Playback of the Disc”
x [MULTI-DISC RESUME] (DVD VIDEO/
VIDEO CD only)
You can set the [MULTI-DISC RESUME] function to on/off.
[ON]: The system stores the resume points in memory for up to 10 discs.
[OFF]: The system does not store the resume points in memory. Playback restarts at the resume point only for the current disc in the unit.
x [RESET]
You can return the [SET UP] settings other than
[PARENTAL CONTROL] to the default
settings. For details, see “Returning the
[SETUP] settings to the default” (page 79).
x [SCREEN SAVER]
You can reduce the damage to the display device
(ghosting). Press any button (e.g., H ) to cancel the screen saver.
[ON]: The screen saver image appears if you do not operate the system for about 15 minutes.
[OFF]: Off.
x [BACKGROUND]
You can select the background color or picture on the TV screen.
[JACKET PICTURE]: The jacket picture (still picture) appears, but only when the jacket picture is already recorded on the disc (CD-
EXTRA, etc.). If the disc does not contain a jacket picture, the [GRAPHICS] picture appears.
[GRAPHICS]: A preset picture stored in the system appears.
[BLUE]: The background is blue.
[BLACK]: The background is black.
Settings for the speakers
[SPEAKER SETUP]
To obtain the best possible surround sound, set connection of the speakers and their distance from your listening position. Then use the test tone to adjust the level and the balance of the speakers to the same level.
SPEAKER SETUP
CONNECTION:
DISTANCE(FRONT):
DISTANCE(SURROUND):
LEVEL(FRONT):
LEVEL(SURROUND):
CENTER:
SURROUND:
SUBWOOFER:
YES
YES
YES
YES x [CONNECTION]
If you do not connect center or surround speakers, set the parameters for [CENTER] and
[SURROUND]. Since the front speaker and subwoofer settings are fixed, you cannot change them.
[FRONT]
[YES]
57 US
58 US
[CENTER]
[YES]: Normally select this.
[NONE]: Select this if no center speaker is used.
[SURROUND]
[YES]: Normally select this.
[NONE]: Select this if no surround speakers are used.
[SUBWOOFER]
[YES]
Note
• When you change the [CONNECTION] setting, the
[STANDARD] of [SPEAKER FORMATION] setting remains the same, but the other settings of
[SPEAKER FORMATION] return to
[STANDARD].
x [DISTANCE (FRONT)]
When you move the front speakers and center speaker, be sure to set the parameters of the distance ( A ) from the listening position to the speakers.
You can set the parameters from 1.0 to 7.0 meters
1)
(3 to 23 ft) for the front speakers, from
0.0 to 7.0 meters
2)
(0 to 23 ft) for the center speaker.
4)
This item appears when you set [CENTER] to [YES] in the [CONNECTION] setting.
x [DISTANCE (SURROUND)]
When you move the surround speakers, be sure to set the parameters of the distance ( B ) from the listening position to the speakers.
You can set the parameters from 0.0 to 7.0 meters
1)
(0 to 23 ft).
B
A
[L/R] 3.0 m/10 ft 3) : Set the front speaker distance.
[CENTER] 3.0 m/10 ft 3)4) : Set the center speaker distance (up to 1.6 meters (5 ft) closer to the front speakers).
1)
0.9 to 6.9 meters for North American models.
2)
0.0 to 6.9 meters for North American models.
3)
When you perform the Quick Setup (page 29), the
default settings are changed.
[L/R] 3.0 m/10 ft 2)3) : Set the surround speaker distance (up to 5.0 meters (16 ft) closer to the front speakers).
1)
0.0 to 6.9 meters for North American models.
2)
When you perform the Quick Setup (page 29), the
default settings are changed.
3)
This item appears when you set [SURROUND] to
[YES] in the [CONNECTION] setting.
Note
• If all front and surround speakers are not placed at an equal distance from your listening position, set the distance according to the closest speaker.
• Do not place the surround speakers farther away from your listening position than the front speakers.
• Depending on the input stream, the [DISTANCE] setting may not be effective.
x [LEVEL (FRONT)]
You can adjust the sound level of the front speakers, center speaker, and subwoofer. You can set the parameters from –6.0 dB to 0 dB for
[L/R], and from –6.0 dB to +6.0 dB for
[CENTER] and [SUBWOOFER]. Be sure to set
[TEST TONE] to [ON] for easy adjustment.
[L/R] 0.0 dB: Set the front speaker level.
[CENTER] 0.0 dB * : Set the center speaker level.
[SUBWOOFER] +2.0 dB: Set the subwoofer level.
* This item appears when you set [CENTER] to
[YES] in the [CONNECTION] setting.
x [LEVEL (SURROUND)]
You can adjust the sound level of the surround speakers. You can set the parameter from –6.0 dB to +6.0 dB. Be sure to set [TEST TONE] to
[ON] for easy adjustment.
[L/R] 0.0 dB * : Set the surround speaker level.
* This item appears when you set [SURROUND] to
[YES] in the [CONNECTION] setting.
x [TEST TONE]
The speakers will emit a test tone to adjust
[LEVEL (FRONT)] and [LEVEL
(SURROUND)].
[OFF]: The test tone is not emitted from the speakers.
[ON]: The test tone is emitted from each speaker in sequence while adjusting the level. When you select one of the [SPEAKER SETUP] items, the test tone is emitted from each speaker in sequence.
Adjust the sound level as follows.
1
Set the [TEST TONE] to [ON].
2
Press C / X / x / c repeatedly to select the desired speaker and the level.
3
Press .
4
Repeat Steps 1 to 3.
5
Press C / X / x / c repeatedly to set [TEST
TONE] to [OFF] after adjusting the speaker level.
Tip
• To adjust the volume of all the speakers at one time, turn the VOLUME control on the unit, or press
VOLUME +/– on the remote.
• To return to the default setting when changing a setting, select the item, then press CLEAR. Note that only the [CONNECTION] setting does not return to the default setting.
59 US
60 US
Tuner
Presetting Radio
Stations
You can preset 20 FM stations, and 10 AM stations. Before tuning, make sure to turn down the volume to minimum.
Current station
Current band and preset number
FM
FM 10 : 88.00 MHz
SONY RADIO
Station name
1
Press FUNCTION +/– repeatedly until
“TUNER FM” or “TUNER AM” appears in the front panel display.
2
Press and hold TUNING +/– until the auto scanning starts.
Scanning stops when the system tunes in a station. “TUNED” and “ST” (stereo program) appear in the front panel display.
3
Press SYSTEM MENU.
4
Press X / x repeatedly until “MEMORY” appears in the front panel display.
5
Press
A preset number appears in the front panel display.
7
Press .
“COMPLETE” appears in the front panel display, and the station is stored.
8
Repeat Steps 2 to 7 to store other stations.
9
Press SYSTEM MENU.
The system menu turns off.
To change the preset number
Select the desired preset number by pressing
PRESET +/– (page 61), then perform the
procedure from Step 3.
To change the AM tuning interval
(except for CIS and Middle
Eastern models)
The AM tuning interval can be set to either
10 kHz or 9 kHz.
To change the AM tuning interval, first tune in any AM station, then turn off the system by pressing " / 1 on the unit. Press " / 1 on the unit while turning OPERATION DIAL on the unit clockwise. The tuning interval changes. If you change the interval, AM preset stations will be erased.
To reset the interval, repeat the same procedure.
6
Press X / x to select the preset number you want.
Tip
• You can select the preset number directly by pressing the number buttons.
Listening to the Radio
Preset radio stations in the system’s memory
first (see “Presetting Radio Stations” (page 60)).
1
Press FUNCTION +/– repeatedly until
“TUNER FM” or “TUNER AM” appears in the front panel display.
The last received station is tuned in.
2
Press PRESET +/– repeatedly to select the preset station.
Each time you press the button, the system tunes in one preset station.
Tip
• You can select the preset station number directly by pressing the number buttons.
3
Adjust the volume by pressing
VOLUME +/–.
To turn off the radio
Press " / 1 .
To listen to non-preset radio stations
Use manual or automatic tuning in Step 2.
For manual tuning, press TUNING +/– repeatedly.
For automatic tuning, press and hold TUNING
+/–. The automatic tuning stops automatically when the system receives the radio station. To stop the automatic tuning manually, press
TUNING +/– or x .
To listen to radio stations when you know the frequencies
Press D.TUNING in Step 2, press the number buttons to select the frequencies, then press .
Tip
• To improve reception, reorient the connected antennas (aerials).
If an FM program is noisy
If an FM program is noisy, you can select monaural reception. There will be no stereo effect, but reception will improve.
1
Press SYSTEM MENU.
2
Press X / x repeatedly until “FM MODE” appears in the front panel display.
3
Press
4
Press X / x to select “MONO.”
• “STEREO”: Stereo reception.
• “MONO”: Monaural reception.
5
Press .
The setting is made.
6
Press SYSTEM MENU.
The system menu turns off.
Naming preset stations
You can enter a name for preset stations. These names (for example, “ABC”) appear in the front panel display when a station is selected.
Only one name can be entered for each preset station.
1
Press FUNCTION +/– repeatedly until
“TUNER FM” or “TUNER AM” appears in the front panel display.
The last received station is tuned in.
2
Press PRESET +/– repeatedly to select the preset station you want to create an index name for.
3
Press SYSTEM MENU.
4
Press X / x repeatedly until “NAME IN” appears in the front panel display.
5
Press
6
Create a name by using C / X / x / c .
Press X / x to select a character, then press c to move the cursor to the next position.
You can input letters, numbers, and other symbols for a radio station.
61 US
62 US
If you make a mistake
Press C / c repeatedly until the character to be changed flashes, then press X / x to select the desired character.
To erase the character, press C / c repeatedly until the character to be erased flashes, then press CLEAR.
7
Press .
“COMPLETE” appears in the front panel display, and the station name is stored.
8
Press SYSTEM MENU.
The system menu turns off.
When the station name is not set
1 Frequency
Ex. “AM1 576”
Viewing the station name or frequency in the front panel display
When the system is set to “TUNER FM” or
“TUNER AM,” you can check the frequency using the front panel display.
Press DISPLAY.
Each time you press DISPLAY, the display changes:
1 t 2 t .... t 1 t ....
x “TUNER FM”
When the station name is set
1 Station name
Ex. “SONY RADIO”
2 Frequency
Ex. “FM1 87.50”
3 The “FM MODE” setting
Ex. “STEREO”
When the station name is not set
1 Frequency
Ex. “FM1 87.50”
2 The “FM MODE” setting
Ex. “STEREO” x “TUNER AM”
When the station name is set
1 Station name
Ex. “SONY RADIO”
2 Frequency
Ex. “AM1 576”
Control for HDMI/External Audio
Device
Using the Control for
HDMI Function for
“BRAVIA” Sync
This function is available on TVs with the
“BRAVIA” Sync function only.
By connecting Sony components that are compatible with the Control for HDMI function with an HDMI cable, operation is simplified as below:
– System Audio Control (page 64)
Control for HDMI is a mutual control function standard used by CEC (Consumer Electronics
Control) for HDMI (High-Definition
Multimedia Interface).
The Control for HDMI function will not work in the following cases:
– When you connect this system to a component which is not compatible with the
Control for HDMI function.
– A component does not have an HDMI jack.
There are convenient buttons on the system’s remote for operating the TV, such as
THEATER, ONE-TOUCH PLAY, TV [ / 1 . For
details, see “Controlling the TV with the
Supplied Remote” (page 73) and refer to the
operating instructions of the TV.
THEATER
ONE-TOUCH
PLAY
TV
BRAVIA Sync
Note
• Depending on the connected component, the Control for HDMI function may not work. Refer to the operating instructions supplied with the component.
• The Control for HDMI function may not work if you connect a component other than a Sony component, even if the component is compatible with the Control for HDMI function.
Preparing the Control for HDMI function
(Control for HDMI - Easy Setting)
The system is compatible with the Control for
HDMI - Easy Setting function. If the TV is compatible with the Control for HDMI - Easy
Setting function, you can set the system’s
[CONTROL FOR HDMI] function automatically by setting the TV. For details, refer to the operating instructions of the TV.
If the TV is not compatible with the Control for
HDMI - Easy Setting function, set the Control for HDMI function of the system and TV manually.
1
Make sure that the system and the TV are connected with an HDMI cable.
2
Turn on the TV and press [ / 1 to turn on the system.
3
Switch the input selector on your TV so that the signal from the system through the HDMI input appears on the TV screen.
4
Set the Control for HDMI function of the system and TV.
For details of the system settings, see the following Steps. For details of the setting of the TV, refer to the operating instructions of the TV (depending on the TV, the default setting of the Control for HDMI function may be set to off).
To set the [CONTROL FOR HDMI] function to on/off
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
63 US
64 US
2
Press DISPLAY while the system is in stop mode.
The Control Menu display appears on the
TV screen.
3
Press X / x to select [SETUP], then press .
The options for [SETUP] appear.
4
Press X / x to select [CUSTOM], then press .
5
The Setup Display appears.
Press X / x press .
to select [HDMI SETUP], then
The options for [HDMI SETUP] appear.
6
Press X / x to select [CONTROL FOR
HDMI], then press .
7
Press X / x to select the setting, then press .
• [ON]: On.
• [OFF]: Off.
Using the Theater Mode
(Theater Mode)
If your TV is compatible with the Theater Mode, you can enjoy optimal image and sound quality suited for movies, and sound is output from the system’s speakers automatically by pressing
THEATER.
Watching a DVD by a single button press
(One-Touch Play)
By only pressing ONE-TOUCH PLAY, the TV turns on, the TV is set for DVD input mode, and the system starts playing a disc automatically.
Note
• One-Touch Play does not work when you press H .
The system and TV work as follows (e.g.):
This system TV
Turns on. (If not already turned on.) r
Switches to “DVD” function.
r
Starts playing the disc and outputs the sound.
Turns on. (If not already turned on.) r
Switches to HDMI input.
r
Minimizes sound level.
(System Audio Control)
Turning the system off in sync with the TV
(System Power Off)
When you turn the TV off by using the POWER button on the TV’s remote or TV [ / 1 on the system’s remote, the system turns off automatically.
Note
• Before using the System Power Off function, set the function for TV power. For details, refer to the operating instructions of the TV.
• Depending on the status of the system (ex. while using other than “DVD” or “TV/VIDEO” functions, or playing a CD), the system may not turn off automatically.
Enjoying TV sound from the speakers by this system
(System Audio Control)
You can enjoy TV sound via this system easily.
To use this function, connect the system and the
TV with an audio cord and an HDMI cable
Depending on the TV, when you set the system to the “TV/VIDEO” function, the System Audio
Control function is activated. TV sound is output from the system speakers, and the volume of the
TV speakers is minimized automatically.
You can use the System Audio Control function as follows:
• While you are watching the TV and the function of the system is switched to “TV/
VIDEO,” TV sound is output from the system speakers automatically.
• While you are watching the TV and the function of the system is switched to “DVD,” sound of the “DVD” function is output from the system speakers; TV sound is not output via the TV speakers.
• You can control the system’s volume by the remote of the TV.
• If you turn the system off or set the function of the system to other than “TV/VIDEO” or
“DVD,” TV sound is output from the TV speakers.
You can also operate the System Audio Control function via the TV menu. For details, refer to the operating instructions of the TV.
Note
• While the TV is in PAP (picture and picture) mode, the System Audio Control function will not work.
When the TV exits PAP mode, the output method of the TV returns to the one before PAP mode.
Tip
• You can connect the system and the TV audio
digitally. For details, see page 23.
Using the DIGITAL MEDIA
PORT Adapter
The DIGITAL MEDIA PORT (DMPORT) adapter is for enjoying sound from a portable audio source or computer. By connecting a
DIGITAL MEDIA PORT adapter, you can enjoy sound from the connected component on the system.
Available DIGITAL MEDIA PORT adapters vary in each area.
For details on connecting the DIGITAL MEDIA
Note
• Do not connect an adapter other than the DIGITAL
MEDIA PORT adapter.
• Do not connect or disconnect the DIGITAL MEDIA
PORT adapter to/from the unit while the system is turned on.
• When you use the system and the Bluetooth Wireless
Audio Adapter (such as TDM-BT1, not supplied) at the same time, transmission distance between the
Bluetooth transmitter and Bluetooth Wireless Audio
Adapter may be reduced. In this case, place the
Bluetooth transmitter as far as possible from the system, or move the Bluetooth Wireless Audio
Adapter closer to the Bluetooth transmitter.
• When you use the system and the Wireless Network
Audio Adapter (such as TDM-NC1, not supplied) at the same time, place the Wireless Network Audio
Adapter as far as possible from the system.
Setting the Maximum Volume
Level of the System
(Volume Limit)
If you change the output method of the TV to the system speakers via the TV menu (or by pressing THEATER), loud sound may be output depending on the volume level of the system.
You can prevent this by limiting the maximum
level of the volume. For details, see “[VOLUME
Changing the language for the on-screen display of the TV
(Language Follow)
When you change the language for the on-screen display of the TV, the system’s on-screen display language is also changed. However, when the system’s on-screen display is displayed, this function does not work.
Playing the connected component on the system
1
Press FUNCTION +/– repeatedly until
“DMPORT” appears in the front panel display.
2
Start playback of the connected component.
The sound and images from the connected component are played on the system or connected TV.
For operation details, refer to the operating instructions of the DIGITAL MEDIA
PORT adapter.
65 US
66 US
Note
• Depending on the type of DIGITAL MEDIA PORT adapter, images are also output. In this case, the system outputs the composite video signal only, regardless of the type of video signal.
Tip
• Depending on the type of DIGITAL MEDIA PORT adapter, you may be able to operate a connected component using either the buttons on the remote or the unit. The following illustration shows an example of buttons that can be used in this case.
Using an S-AIR Product
The unit is compatible with the S-AIR function
(page 93), which allows sound transmission
between S-AIR products.
About S-AIR products
There are two types of S-AIR products.
• S-AIR main unit (this unit): This is for transmitting sound. You can use up to three
S-AIR main units. (The number of usable
S-AIR main units depends on the use environment.)
• S-AIR sub unit: This is for receiving sound.
– Surround amplifier : You can enjoy surround speaker sound wirelessly.
– S-AIR receiver : You can enjoy system sound in another room.
Room A
S-AIR main unit
./>
H x
X
S-AIR sub unit
(surround amplifier)
Room B
S-AIR sub unit
(S-AIR receiver)
Note
• You cannot operate this function if you do not insert the wireless transceiver into the unit correctly
Establishing sound transmission between the unit and S-AIR sub unit
(ID setting)
For the surround amplifier
For the S-AIR receiver
Simply by matching the ID of the unit and the
S-AIR sub unit, you can establish sound transmission.
To set the ID of the unit
1
Press " / 1 on the unit.
The system turns on.
2
Press SYSTEM MENU.
3
Press X / x repeatedly until “S-AIR ID” appears in the front panel display, then press c .
4
Press X / x to select the desired ID.
You can select any ID (A, B, or C).
5
Press .
The setting is made.
6
Press SYSTEM MENU.
The system menu turns off.
7
Set the S-AIR sub unit to the same ID.
Sound transmission is established as follows (example):
S-AIR main unit
(This unit)
ID A
unit (page 69), “(PAIRING)” appears beside ID in
the front panel display.
To set the ID of the surround amplifier
Refer to the operating instructions of the surround amplifier.
To set the ID of the S-AIR receiver
Refer to the operating instructions of the S-AIR receiver.
To use multiple S-AIR main units
You can use multiple S-AIR main units by setting a different ID for each component.
S-AIR main unit
(This unit)
ID A
Other S-AIR main unit
ID B
ID A
S-AIR sub unit
ID A
S-AIR sub unit
ID B
S-AIR sub unit
ID A
S-AIR sub unit
ID A
S-AIR sub unit
Tip
• To confirm the current ID, perform Steps 1 to 3 above. When you pair the unit with the S-AIR sub
Enjoying the system’s sound in another room
For the S-AIR receiver
You can enjoy the system’s sound by using the
S-AIR receiver. The S-AIR receiver can be placed in another room for enjoying the system’s sound there.
For details of the S-AIR receiver, refer to the operating instructions of the S-AIR receiver.
1
Press SYSTEM MENU.
2
Press X / x repeatedly until “S-AIR
MODE” appears in the front panel display, then press or c .
67 US
68 US
3
Press X / x to select the desired setting.
• “PARTY”: The S-AIR receiver outputs sound according to functions set on the unit.
• “SEPARATE”: You can set the desired function for the S-AIR receiver while unit functions do not change.
4
Press .
The setting is made.
5
Press SYSTEM MENU.
The system menu turns off.
6
Select the desired function on the
S-AIR receiver.
x When “PARTY” is set
The S-AIR receiver’s function changes sequentially as you press FUNCTION +/–
of the main unit (page 32) or S-AIR CH of
the S-AIR receiver.
x When “SEPARATE” is set
The S-AIR receiver’s function changes by pressing S-AIR CH of the S-AIR receiver as follows.
“MAIN UNIT” t “TUNER FM” t
“TUNER AM” t “DMPORT” t
“AUDIO” t …
To enjoy the same function as the unit, select “MAIN UNIT.”
When “TUNER FM” or “TUNER AM” is selected on the unit, you can only select the same band for the tuner on the S-AIR receiver. In this case, when you select other than “TUNER FM” or “TUNER AM” on the unit, you can select any band for the tuner on the S-AIR receiver.
7
Adjust the volume on the S-AIR receiver.
Note
• When the sound is other than 2 channel stereo, multichannel sound is downmixed to 2 channel.
To set “S-AIR MODE” via the remote
Press S-AIR MODE.
The S-AIR mode appears in the front panel display. Each time you press S-AIR MODE, the
S-AIR mode changes.
To control the system from the
S-AIR receiver
You can control the system from the S-AIR receiver by using the following buttons.
Press
H , X , x ,
.
/ >
S-AIR CH
Operation
Share the same operations on the remote and unit.
Change the function of the system.
For details, refer to the operating instructions of the S-AIR receiver.
Enjoying the S-AIR receiver while the unit is in standby mode
For the S-AIR receiver
You can enjoy the S-AIR receiver while the unit is in standby mode by setting “S-AIR STBY” to
“STBY ON.”
1
Press SYSTEM MENU.
2
Press X / x repeatedly until “S-AIR
STBY” appears in the front panel display, then press or c .
3
Press X / x to select the desired setting.
• “STBY ON”: You can enjoy the S-AIR receiver while the unit is in standby mode or turned on. The power consumption during the standby mode increases.
• “STBY OFF”: You cannot enjoy the
S-AIR receiver while the unit is in standby mode.
The default setting differs depending on the area.
4
Press .
The setting is made.
5
Press SYSTEM MENU.
The system menu turns off.
Note
• When you turn the system off while “S-AIR STBY” is set to “STBY ON,” “S-AIR” flashes (when sound transmission between the unit and S-AIR receiver is not established), or lights up (when sound transmission between the unit and S-AIR receiver is established) in the front panel display.
x After pairing
Sound transmission is established between the paired unit and S-AIR sub unit(s) only.
Your room Neighbor
This unit
ID A No transmission
Identifying the unit with a specific S-AIR sub unit
(Pairing operation)
For the surround amplifier
For the S-AIR receiver
It is easy to set the same ID for the unit and an
S-AIR sub unit, such as a surround amplifier or
S-AIR receiver, to establish sound transmission.
However, neighbors may also receive your system’s sound if IDs are the same, or you may receive sound from neighbors. To prevent this, you can identify the unit with a specific S-AIR sub unit by performing the pairing operation.
x Before pairing
Sound transmission is established by ID
(example).
Your room
This unit
Neighbor
ID A
ID A
S-AIR sub unit
ID A
S-AIR sub unit
ID A
S-AIR sub unit
ID A
S-AIR sub unit
Pairing
To perform pairing
1
Place the S-AIR sub unit that you want to pair near the unit.
Note
• Remove headphones from the surround amplifier (if connected).
2
Match the IDs of the unit and the S-AIR sub unit.
• To set the ID of the unit, see “To set the ID of the unit” (page 67).
• To set the ID of the S-AIR receiver, refer to the operating instructions of the S-AIR receiver.
• To set the ID of the surround amplifier, refer to the operating instructions of the surround amplifier.
3
Press SYSTEM MENU.
4
Press X / x repeatedly until “PAIRING” appears in the front panel display, then press c .
5
After “START” appears in the front panel display, press .
The unit starts pairing and “SEARCH” flashes in the front panel display.
To cancel pairing, press SYSTEM MENU.
6
Start pairing of the S-AIR sub unit.
x For the surround amplifier
Refer to the operating instructions of the surround amplifier.
69 US
70 US
When sound transmission is established,
“PAIRING” and “COMPLETE” appear alternately in the front panel display.
x For the S-AIR receiver
Refer to the operating instructions of the
S-AIR receiver.
When sound transmission is established,
“PAIRING” and “COMPLETE” appear alternately in the front panel display.
Note
• Perform pairing within several minutes of Step
5. If you do not, “PAIRING” and
“INCOMPLETE” appear alternately in the front panel display. To continue pairing, press and start again from Step 5. To cancel pairing, press
SYSTEM MENU.
7
Press SYSTEM MENU.
The system menu turns off.
Note
• After you have performed pairing, if you select
“S-AIR ID” (page 69), the ID setting (“A,” “B,” or
“C”) that you last used is displayed first by default.
To cancel pairing
Perform the ID setting of the unit according to
the procedure of “To set the ID of the unit.” If
you select a new ID, pairing is canceled.
If sound transmission is unstable
For the surround amplifier
For the S-AIR receiver
If you use multiple wireless systems which share the 2.4 GHz band, such as wireless LAN or
Bluetooth, the transmission of S-AIR products or other wireless systems may be unstable. In this case, the transmission may be improved by changing the following “RF CHANGE” setting.
1
Press SYSTEM MENU.
2
Press X / x repeatedly until “RF
CHANGE” appears in the front panel display, then press or c .
3
Press X / x to select the desired setting.
• “AUTO”: Normally select this. The system changes “RF CHANGE” to “ON” or “OFF” automatically.
• “ON”: The system transmits sound by searching for the better channel for transmitting.
• “OFF”: The system transmits sound by fixing the channel for transmitting.
4
Press .
The setting is made.
5
Press SYSTEM MENU.
The system menu turns off.
6
When you set “RF CHANGE” to “OFF,” select the ID so that sound
transmission is most stable (page 67).
Note
• In most cases, you will not need to change this setting.
– If “RF CHANGE” is set to “OFF,” transmission between the unit and S-AIR sub unit can be performed using one of the following channels.
– S-AIR ID A: equivalent channel for IEEE
802.11b/g channel 1
– S-AIR ID B: equivalent channel for IEEE
802.11b/g channel 6
– S-AIR ID C: equivalent channel for IEEE
802.11b/g channel 11
• The transmission may be improved by changing the transmission channel (frequency) of the other wireless system(s). For details, refer to the operating instructions of the other wireless system(s).
Changing the RF output power
(Only when using the EZW-RT10A wireless transceiver.)
1
Press SYSTEM MENU.
2
Press X / x repeatedly until “RF
POWER” appears in the front panel display, then press or c .
3
Press X / x to select the desired setting.
• “HIGH”: Normally select this.
• “LOW”: The RF output power is decreased.
4
Press .
The setting is made.
5
Press SYSTEM MENU.
The system menu turns off.
Other Operations
Getting Optimal
Surround Sound for a
Room
[SPEAKER FORMATION]
Depending on the shape of the room, you cannot install some speakers. For better surround sound, Sony recommends that first you decide the position of the speakers.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
2
Press DISPLAY while the system is in stop mode.
The Control Menu display appears on the
TV screen.
3
Press X / x to select [SETUP], then press .
The options for [SETUP] appear.
4
Press X / x to select [CUSTOM], then press .
The Setup Display appears.
5
Press X / x to select [AUDIO SETUP], then press .
The options for [AUDIO SETUP] appear.
6
Press X / x to select [SPEAKER
FORMATION], then press .
The options for [SPEAKER
FORMATION] appear.
SPEAKER FORMATION
7
Press C / c to select a setting.
• [STANDARD]: Select this when you install all the speakers normally.
• [NO CENTER]: Select this when you install the front and surround speakers only.
• [NO SURROUND]: Select this when you install the center and front speakers only.
• [FRONT ONLY]: Select this when you install the front speakers only.
• [ALL FRONT]: Select this when you install all the speakers in front of the listening position.
• [ALL FRONT - NO CENTER]: Select this when you install the front and surround speakers in front of the listening position.
8
Press .
The setting is made and the confirmation display appears.
9
Press C / c to select [YES] or [NO], then press .
• [YES]: Continue with [AUTO
CALIBRATION]. Follow the procedure
from Step 7 of “Calibrating the
Appropriate Settings Automatically”
• [NO]: Exit [SPEAKER FORMATION].
STANDARD
71 US
72 US
Calibrating the
Appropriate Settings
Automatically
[AUTO CALIBRATION]
D. C. A. C. (Digital Cinema Auto Calibration) can set the appropriate surround sound automatically.
Note
• The system outputs a loud test sound when [AUTO
CALIBRATION] starts. You cannot turn the volume down. Give consideration to children and neighbors.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
2
Press DISPLAY while the system is in stop mode.
The Control Menu display appears on the
TV screen.
3
Press X / x to select [SETUP], then press .
The options for [SETUP] appear.
4
Press X / x to select [CUSTOM], then press .
The Setup Display appears.
5
Press X / x to select [AUDIO SETUP], then press .
The options for [AUDIO SETUP] appear.
6
Press X / x to select [AUTO
CALIBRATION], then press .
The options for [AUTO CALIBRATION] appear.
7
Connect the calibration mic (supplied) to the A.CAL MIC jack on the front panel.
Set up the calibration mic at ear level using a tripod, etc. (not supplied).
The front of each speaker should face the calibration mic, and there should be no obstruction between the speakers and the calibration mic.
Calibration mic
8
Press C / c to select [YES].
9
Press .
[AUTO CALIBRATION] starts.
Be quiet during the measurement.
Note
• Before [AUTO CALIBRATION], make sure that the surround amplifier turns on and you install the surround amplifier in the appropriate location. If you install the surround amplifier in an improper location, such as another room, proper measurement will not be obtained.
• The environment of the room in which the system is installed may affect measurements.
When the measurements differ considerably from the status of the speaker installation, perform the speaker settings manually by
following “Settings for the speakers” (page 57).
10
Press C / c to select [YES] or [NO], then press .
x The measurement is OK.
Disconnect the calibration mic, then select
[YES]. The result is implemented.
When you want to cancel the measurement and retry [AUTO CALIBRATION], select
[NO].
x The measurement is not OK.
Follow the message, then select [YES] to retry.
Note
• While the Auto Calibration function is working, do not operate the system.
• The measurement for [SUBWOOFER] is always
[YES] since the system does not perform subwoofer calibration, but the [SUBWOOFER] level in
[SPEAKER SETUP] returns to the default setting when you perform [AUTO CALIBRATION].
Controlling the TV with the Supplied Remote
You can control the TV (Sony only) by using the following buttons. Use these buttons (other than
TV [ / 1 , THEATER, TV INPUT, and TV VOL
+/–) while pressing the TV button.
Note
• Depending on the TV, you may not be able to control your TV or to use some of the buttons.
By pressing
TV [ / 1
THEATER
TV INPUT
You can
Turn the TV on/off.
Enjoy optimal image quality suited for movies.
Switch the TV’s input source between the TV and other input sources.
TV VOL +/–
TV CH +/–*
Adjust the TV volume.
Select the TV channel.
Number buttons*, *,
ENTER*
Select the TV channel.
TOOLS*
RETURN*
Displays the operation menu for the current display.
Return to the previous channel or layer on the menu of the TV.
Display the menu of the TV.
MENU*
MUTING* Turn off the TV sound temporarily.
C / X / x / c *, * Select the item on the menu.
* Use these buttons while pressing the TV button.
73 US
74 US
Using the Sound Effect
Reinforcing bass frequencies
You can reinforce bass frequencies.
Press DYNAMIC BASS.
“D. BASS ON” appears in the front panel display and bass frequencies are effectively reinforced.
To turn off the sound effect
Press DYNAMIC BASS again.
Enjoying the sound at low volume
You can enjoy sound effects or dialogue, as you would in a movie theater, even at low volume. It is useful for watching movies at night.
Press NIGHT.
“NIGHT ON” appears in the front panel display and the sound effect is activated.
Note
• This effect does not work for a Super Audio CD.
When you load a Super Audio CD during “NIGHT
ON,” the sound effect turns off automatically.
• When sound is output from the center speaker, this effect is more pronounced, as speech (movie dialog, etc.) is easy to hear. When sound is not output from the center speaker, or you are using the headphones, the system optimally adjusts the volume.
To turn off the sound effect
Press NIGHT again.
Enhancing compressed sound
You can enhance compressed sound such as an
MP3 audio file.
This effect is activated automatically when all the following conditions are satisfied:
– The function is set to “DMPORT” or
“AUDIO”.
– “DEC. MODE” is set to “A.F.D. STD,”
“A.F.D. MULTI,” or “2CH STEREO”.
– Headphones are not connected.
When all the conditions above are satisfied, you can activate/deactivate the effect by pressing
DMPORT BOOSTER on the unit. The
DMPORT BOOSTER indicator turns on.
To turn off the sound effect
Press DMPORT BOOSTER on the unit so that the DMPORT BOOSTER indicator turns off.
Selecting the Effect to
Suit the Source
You can select a suitable sound mode for movies or music.
Press SOUND MODE repeatedly during playback until the desired mode appears in the front panel display.
• “AUTO”: The system automatically selects
“MOVIE” (the MOVIE indicator lights up) or
“MUSIC” (the MUSIC indicator lights up) to produce the sound effect depending on the source.
• “MOVIE”: The system provides the sound for movies. The MOVIE indicator lights up.
• “MUSIC”: The system provides the sound for music. The MUSIC indicator lights up.
Note
• When you play a Super Audio CD, this function does not work.
• You cannot operate these setup items when you connect headphones to the unit or surround amplifier.
• When changing the sound mode while using the
S-AIR receiver, sound from the S-AIR receiver may skip.
Enjoying Multiplex
Broadcast Sound
(DUAL MONO)
You can enjoy multiplex broadcast sound when the system receives or plays a Dolby Digital multiplex broadcast signal.
Note
• To receive a Dolby Digital signal, you need to connect a TV or other component to the unit with an
optical or coaxial digital cord (page 23) and set the
digital output mode of the TV or other component to
Dolby Digital.
Press AUDIO repeatedly until the desired signal appears in the front panel display.
• “MAIN”: Sound of the main language will be output.
• “SUB”: Sound of the sub language will be output.
• “MAIN+SUB”: Mixed sound of both the main and sub languages will be output.
75 US
76 US
Changing the Input Level of the Sound from
Connected Components
Distortion may occur when you listen to a component connected to the TV/VIDEO jacks on the rear panel, or to the AUDIO IN jack on the front panel. Distortion is not a malfunction and will depend on the component connected.
To prevent distortion, reduce the input level on the unit.
1
Press FUNCTION +/– repeatedly until
“TV/VIDEO” or “AUDIO” appears in the front panel display.
2
Press SYSTEM MENU.
3
Press X / x repeatedly until
“ATTENUATE” appears in the front panel display, then press or c .
4
Press X / x to select a setting.
• “ATT ON”: You can attenuate the input level. The output level is changed.
• “ATT OFF”: Normal input level.
5
Press .
The setting is made.
6
Press SYSTEM MENU.
The system menu turns off.
Using the Sleep Timer
You can set the system to turn off at a preset time, so you can fall asleep listening to music.
You can preset the time in 1 or 10-minute increments.
Press SLEEP.
Each time you press SLEEP, the minutes display
(the remaining time) changes by 10 minutes.
When you set the sleep timer, “SLEEP” flashes in the front panel display.
To check the remaining time
Press SLEEP once.
To change the remaining time
Press SLEEP repeatedly to select the desired time.
To cancel the sleep timer function
Press SLEEP repeatedly until “SLEEP OFF” appears in the front panel display.
To set the sleep timer using the system menu
1
Press SYSTEM MENU.
2
Press X / x repeatedly until “SLEEP” appears in the front panel display, then press c .
3
Press X / x to select a setting.
The minutes display (the remaining time) changes by 10 minutes.
Tip
• You can select the remaining time by pressing the number buttons. In this case, you can preset the time in 1-minute increments.
4
Press .
The setting is made and “SLEEP” flashes in the front panel display.
5
Press SYSTEM MENU.
The system menu turns off.
Changing the Brightness of the Front Panel
Display
You can set the brightness of the front panel display to either of 2 levels.
1
Press SYSTEM MENU.
2
Press X / x repeatedly until “DIMMER” appears in the front panel display, then press c .
3
Press X / x to select the brightness of the front panel display.
• “DIMMER OFF”: The front panel display is bright.
• “DIMMER ON”: The front panel display is dark.
4
Press .
The setting is made.
5
Press SYSTEM MENU.
The system menu turns off.
Viewing Information
About the Disc
Viewing the playing time and remaining time in the front panel display
Press DISPLAY repeatedly.
Each time you press DISPLAY while playing the disc, the display changes:
1 t 2 t ... t 1 t ...
Some displayed items may disappear after a few seconds.
x DVD VIDEO/DVD-VR
1 Playing time of the current title
2 Remaining time of the current title
3 Playing time of the current chapter
4 Remaining time of the current chapter
5 Disc name
6 Title and chapter x VIDEO CD (without PBC functions)/
Super Audio CD/CD
1 Playing time of the current track
2 Remaining time of the current track
3 Playing time of the disc
4 Remaining time of the disc
5 Track name
6 Track and index*
* VIDEO CD/Super Audio CD only.
x Super VCD
1 Playing time of the current track
2 Track text
3 Track and index number x DATA CD (MP3 file)/DATA DVD (MP3 file)
1 Playing time and current track number
2 Track (file) name*
* If an MP3 file has an ID3 tag, the system will display an album name or title name from the ID3 tag information.
The system can support ID3 ver 1.0/1.1/2.2/2.3.
ID3 ver 2.2/2.3 tag information display has priority when both ID3 ver 1.0/1.1 and ver 2.2/2.3 tags are used for a single MP3 file.
77 US
78 US
Note
• The system can only display the first level of the
DVD/CD text, such as the disc name or title.
• If a file name of the MP3 file cannot be displayed, “*” will appear in the front panel display instead.
• The disc name or track name may not be displayed depending on the text.
• Playing time of MP3 files may not be displayed correctly.
Tip
• When the system is playing a VIDEO CD with PBC functions, the playing time is displayed.
• T-**:**
Remaining time of the current track
• D **:**
Playing time of the current disc
• D-**:**
Remaining time of the current disc x DATA CD (MP3 file)/DATA DVD (MP3 file)
• T **:**
Playing time of the current track
Note
• Characters/marks may not be displayed in some languages.
• Depending on the type of disc being played, the system can only display a limited number of characters. Also, depending on the disc, not all text characters will be displayed.
Viewing the playing time and remaining time on the TV screen
1
Press DISPLAY during playback.
The following display appears on the TV screen.
T 1: 01: 40
Time information
2
Press DISPLAY repeatedly to change the time information.
The display and the kinds of time that you can check depend on the disc you are playing.
x DVD VIDEO/DVD-VR
• T **:**:**
Playing time of the current title
• T-**:**:**
Remaining time of the current title
• C **:**:**
Playing time of the current chapter
• C-**:**:**
Remaining time of the current chapter x VIDEO CD (with PBC functions)
• **:**
Playing time of the current scene x VIDEO CD (without PBC functions)/
Super Audio CD/CD
• T **:**
Playing time of the current track
Checking the play information of the disc
To check DVD/Super Audio CD/CD text
Press DISPLAY repeatedly during playback to display text recorded in the DVD/Super Audio
CD/CD.
The DVD/Super Audio CD/CD text appears only when text is recorded in the disc. You cannot change the text. If the disc does not contain text, “NO TEXT” appears.
Dvorak/Tchaikovsky /NedPho/Kreizberg
Adagio - Allegro molto
To check DATA CD/DATA DVD
(MP3 file) text
By pressing DISPLAY while playing MP3 files on a DATA CD/DATA DVD, you can display the name of the folder/MP3 file, and the audio bit rate (the amount of data per second of the current audio) on the TV screen.
Bit rate *
T 0: 13 192k MP3
Returning to the Default
Settings
Returning the system parameters, such as preset stations, to the default settings
2002_Remixes
Soul_Survivor_rap_version
Folder name ** File name **
* The bit rate appears when the system is playing an
MP3 file on a DATA CD/DATA DVD.
** If an MP3 file has the ID3 tag, the system will display an album name or title name from the ID3 tag information.
The system can support ID3 ver 1.0/1.1/2.2/2.3.
ID3 ver 2.2/2.3 tag information display has priority when both ID3 ver 1.0/1.1 and ver 2.2/2.3 tags are used for a single MP3 file.
" / 1 N x
1
Press " / 1 to turn on the system.
2
Press x , N , and " / 1 on the unit at the same time.
“COLD RESET” appears in the front panel display and the system returns to default settings.
Checking the date information of a JPEG image file
You can check the date information during playback when the Exif* tag is recorded in the
JPEG image file.
Press DISPLAY during playback.
The Control Menu display appears on the TV screen.
5 ( 8 )
1 0 ( 1 5 )
9 / 1 8 / 2 0 0 2
DATA CD
Date information
* “Exchangeable Image File Format” is a digital camera image format defined by the Japan
Electronics and Information Technology Industries
Association (JEITA).
Returning the [SETUP] settings to the default
You can return the [SETUP] settings (page 52)
other than [PARENTAL CONTROL] to the default settings.
1
Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel display.
2
Press DISPLAY while the system is in stop mode.
The Control Menu display appears on the
TV screen.
3
Press X / x to select [SETUP], then press .
The options for [SETUP] appear.
4
Press X / x to select [CUSTOM], then press .
The Setup Display appears.
79 US
80 US
5
Press X / x to select [SYSTEM SETUP], then press .
The options for [SYSTEM SETUP] appear.
6
Press X / x to select [RESET] and press c .
7
Press C / c to select [YES].
You can also quit the process and return to the Control Menu display by selecting [NO] here.
8
Press .
Do not press [/1 while resetting the system as it takes a few seconds to complete.
Note
• The [MEDIA], [INTERVAL], [EFFECT], and
[MULTI/2CH] settings also return to the default settings.
Additional Information
Precautions
On power sources
• Unplug the unit from the wall outlet (mains) if you do not intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the cord.
On placement
• Place the system in a location with adequate ventilation to prevent heat build-up in the system.
• At high volume, over long periods of time, the cabinet becomes hot to the touch. This is not a malfunction.
However, touching the cabinet should be avoided. Do not place the system in a confined space where ventilation is poor as this may cause overheating.
• Do not block the ventilation slots by putting anything on the system. The system is equipped with a high power amplifier. If the ventilation slots are blocked, the system can overheat and malfunction.
• Do not place the system on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.
• Do not install the system near heat sources such as radiators, or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration, or shock.
• Do not install the system in an inclined position. It is designed to be operated in a horizontal position only.
• Keep the system and discs away from components with strong magnets, such as microwave ovens, or large loudspeakers.
• Do not place heavy objects on the system.
On operation
• If the system is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the unit. Should this occur, the system may not operate properly. In this case, remove the disc and leave the system turned on for about half an hour until the moisture evaporates.
• When you move the system, take out any disc. If you don’t, the disc may be damaged.
• If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.
On adjusting volume
• Do not turn up the volume while listening to a section with very low level inputs or no audio signals. If you do, the speakers may be damaged when a peak level section is suddenly played.
On cleaning
• Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.
If you have any questions or problems concerning your system, please consult your nearest Sony dealer.
On cleaning discs, disc/lens cleaners
• Do not use cleaning discs or disc/lens cleaners
(including wet or spray types). These may cause the apparatus to malfunction.
On your TV’s color
• If the speakers should cause the TV screen to have color irregularity, turn off the TV then turn it on after
15 to 30 minutes. If color irregularity should persist, place the speakers further away from the TV set.
IMPORTANT NOTICE
Caution: This system is capable of holding a still video image or on-screen display image on your television screen indefinitely. If you leave the still video image or on-screen display image displayed on your TV for an extended period of time you risk permanent damage to your television screen.
Projection televisions are especially susceptible to this.
On moving the system
1
Press FUNCTION +/– repeatedly to select “DVD.”
2
Make sure that all discs are removed from the unit.
3
Press H and " / 1 simultaneously.
“MECHA LOCK” and “UNPLUG” appear alternately in the front panel display.
4
Remove the AC power cord (mains lead) from the wall outlet (mains).
81 US
82 US
About S-AIR function
• As the S-AIR product(s) transmits sound by radio waves, sound may skip when radio waves are obstructed. This is a characteristic of radio waves and is not malfunction.
• As the S-AIR product(s) transmits sound by radio waves, equipment that generates electromagnetic energy, such as a microwave oven, may prevent sound transmission.
• As the S-AIR product(s) uses the radio waves that share the same frequency as other wireless systems, such as wireless LAN or Bluetooth devices it may occur interference or poor transmission as a result. In this case, take the following steps to enhance the transmission of signals:
– Avoid placing the S-AIR product(s) near other wireless systems.
– Avoid using the S-AIR product(s) and the other wireless systems spontaneously.
– The transmission may be improved by changing the transmission channel (frequency) of the other wireless system(s). For details, refer to the operating instructions of the other wireless system(s).
• The transmission distance differs depending on the usage of environment. Find a location where transmission between the S-AIR main unit and sub unit is most effective, and install the S-AIR main unit and sub unit there.
• Place the S-AIR product(s) on the stable surface off the floor.
• Poor transmission may occur and the transmission distance may be too short if the following conditions exist:
– There is a wall/floor made of reinforced concrete or stone between the S-AIR product(s).
– There is an iron divider/door or furniture/electric product made of fireproof glass, metal, etc., between the S-AIR product(s).
Notes about the Discs
On handling discs
• To keep the disc clean, handle the disc by its edge. Do not touch the surface.
• Do not stick paper or tape on the disc.
• Do not expose the disc to direct sunlight or heat sources such as hot air ducts, or leave it in a car parked in direct sunlight as the temperature may rise considerably inside the car.
• After playing, store the disc in its case.
On cleaning
• Before playing, clean the disc with a cleaning cloth.
Wipe the disc from the center out.
• Do not use solvents such as benzine, thinner, commercially available cleaners, or anti-static spray intended for vinyl LPs.
This system can only play back a standard circular disc. Using neither standard nor circular discs (e.g., card, heart, or star shape) may cause a malfunction.
Do not use a disc that has a commercially available accessory attached, such as a label or ring.
Troubleshooting
If you experience any of the following difficulties while using the system, use this troubleshooting guide to help remedy the problem before requesting repairs. Should any problem persist, consult your nearest Sony dealer.
Note that if service personnel changes some parts during repair, these parts may be retained.
In the event of a problem with the S-AIR function, have a Sony dealer check the entire system together
(main unit and S-AIR sub unit).
Power
Symptom
The power is not turned on.
If “PROTECTOR” and “PUSH
POWER” appear alternately in the front panel display.
Remedy
• Check that the AC power cord (mains lead) is connected securely.
• Press " / 1 after “STANDBY” disappears from the front panel display.
Press " / 1 to turn off the system, and check the following items after
“STANDBY” disappears.
• Are the + and – speaker cords short-circuited?
• Are you using only the specified speakers?
• Is anything blocking the ventilation holes of the system?
• After checking the above items and fixing any problems, turn on the system. If the cause of the problem cannot be found even after checking all the above items, consult your nearest Sony dealer.
83 US
84 US
Picture
Symptom
There is no picture.
Remedy
• The video connecting cords are not connected securely.
• The video connecting cords are damaged.
• The unit is not connected to the correct TV input jack (page 22).
• The video input on the TV is not set so that you can view pictures from the system.
• Check the output method on your system (page 22).
• You have set progressive format but your TV cannot accept the signal in progressive format. In this case, return the setting to interlace format (the
• Even if your TV is compatible with progressive format (525p/625p) signals, the image may be affected when you set progressive format. In this case, return the
setting to interlace format (the default setting) (page 31).
• Re-connect the connecting cord securely.
• The unit is connected to an input device that is not HDCP (High-bandwidth
Digital Content Protection) compliant (“HDMI” on the front panel does not
• If the HDMI OUT jack is used for video output, change the type of video signal
output from the HDMI OUT jack. It may solve the problem (page 31).
Connect the TV and the unit using a video jack other than the HDMI OUT, and switch the TV’s input to the connected video input so that you can see the onscreen displays. Change the type of video signal output from the HDMI OUT jack, and switch the TV’s input back to HDMI. If the picture still does not appear, repeat the Steps and try other options.
• You have set [PROGRESSIVE (COMPONENT OUT)] in [VIDEO SETUP] to
[ON] (page 54) even though your TV cannot accept the progressive signal. In
this case, disconnect the HDMI cable from the unit and then set it to [OFF].
• If you are using the “DMPORT” function, the video signal is output from the
VIDEO OUT jack only.
Picture noise appears.
Even though you set the aspect ratio in [TV TYPE] of [VIDEO
SETUP], the picture does not fill the TV screen.
• The aspect ratio on the disc is fixed.
Color irregularity occurs on the
TV screen.
• The disc is dirty or flawed.
• If the picture output from your system goes through your VCR to get to your
TV, the copy-protection signal applied to some DVD programs could affect picture quality. If you experience problems when you connect your unit through
your VCR, try connecting your unit to your TV’s video input directly (page 22).
The system’s speakers contain magnet parts, so magnetic distortion may occur.
When color irregularity occurs on the TV screen, check the following items.
• If the speakers are used with a CRT-based TV or projector, install the speakers at least 0.3 meters (1.0 ft) from the TV set.
• If the color irregularity persists, turn off the TV set once, then turn it on after 15 to 30 minutes.
• If howling occurs, reposition the speakers farther away from the TV set.
• Make sure that no magnetic object (magnetic latch on a TV stand, health care device, toy, etc.) is placed near the speakers.
Sound
Symptom
There is no sound.
No sound is output from the
HDMI OUT jack.
Remedy
• The speaker cord is not connected securely.
• Press MUTING on the remote if “MUTING ON” is displayed in the front panel display.
• The system is in pause mode or in Slow-motion Play mode. Press H to return to normal play mode.
• Fast forward or fast reverse is being performed. Press H to return to normal play mode.
• Check the speaker settings (page 57).
• Super Audio CD audio signals are not output from the HDMI OUT jack.
• The component connected to the HDMI OUT jack does not conform to the audio signal format, in this case set [AUDIO (HDMI)] in [HDMI SETUP] to
• Set [AUDIO (HDMI)] in [HDMI SETUP] to [ON] (page 55).
• The HDMI OUT jack is connected to a DVI (Digital Visual Interface) device
(DVI (Digital Visual Interface) jacks do not accept audio signals).
• The HDMI OUT jack does not output Super Audio CD sound.
• Try the following: 1 Turn the system off and on again. 2 Turn the connected component off and on again. 3 Disconnect and then connect the HDMI cable again.
• Check that the speakers and components are connected correctly and securely.
The left and right sounds are unbalanced or reversed.
There is no sound from the subwoofer.
• Check the speaker connections and settings (pages 21, 57).
Severe hum or noise is heard.
• Check that the speakers and components are connected securely.
• Check that the connecting cords are away from a transformer or motor, and at least 3 meters (10 ft) away from your TV set or a fluorescent light.
• Move your TV away from the audio components.
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol.
• Clean the disc.
The sound loses stereo effect when you play a VIDEO CD, a
CD, or an MP3 file.
• Select stereo sound by pressing AUDIO (page 38).
• Make sure the unit is connected properly.
The surround effect is difficult to hear when you are playing a sound track of Dolby Digital,
DTS, or MPEG audio.
• Check the “ DEC. MODE
.
• Check the speaker connections and settings (pages 21, 57).
• Depending on the DVD, the output signal may not be the entire 5.1 channel. It may be monaural or stereo even if the sound track is recorded in Dolby Digital or MPEG audio format.
The sound comes from the center speaker only.
• Depending on the disc, the sound may come from the center speaker only.
No sound is heard from the center speaker.
• Check the speaker connections and settings (pages 21, 57).
• Check the “ DEC. MODE
• Depending on the source, the effect of the center speaker may be less noticeable.
• A 2 channel source is being played.
.
85 US
86 US
Symptom
No sound or only a very lowlevel sound is heard from the surround speakers.
Remedy
• Check the speaker connections and settings (pages 21, 57).
• Check the “ DEC. MODE
.
• Depending on the source, the effect of the surround speakers may be less noticeable.
• A 2 channel source is being played.
• The sampling frequency of the input stream is more than 48 kHz.
There is no sound from the
DIGITAL IN COAXIAL/
OPTICAL jack.
Noise is heard on AM radio.
• Check the location of the AM loop antenna (aerial) and cord (page 26).
Operation
Symptom
Radio stations cannot be tuned in.
Remedy
• Check that the antenna (aerial) is connected securely. Adjust the antenna
(aerial) or connect an external antenna (aerial) if necessary.
• The signal strength of the stations is too weak (when tuning in with automatic tuning). Use direct tuning.
• No stations have been preset or the preset stations have been cleared (when
tuning by scanning preset stations). Preset the stations (page 60).
The remote does not function.
• There are obstacles between the remote and the unit.
• The distance between the remote and the unit is too far.
• The remote is not pointed at the remote sensor on the unit.
• The batteries in the remote are weak.
The disc does not play.
• There is no disc inserted.
• The disc is upside down.
Insert the disc with the playback side facing down.
• The disc is skewed on the disc tray.
• The system cannot play CD-ROMs, etc. (page 7).
• The region code on the DVD does not match the system.
• Moisture has condensed inside the unit and may cause damage to the lenses.
Remove the disc and leave the unit turned on for about half an hour.
The MP3 file cannot be played.
• The DATA CD is not recorded in ISO 9660 Level 1/Level 2, or Joliet.
• The DATA DVD is not recorded in UDF (Universal Disk Format).
• The MP3 file does not have the extension “.mp3.”
• The data is not formatted in MP3 even though it has the extension “.mp3.”
• The data is not MPEG1 Audio Layer 3 data.
• The system cannot play audio tracks in MP3PRO format.
• Check the [MEDIA] setting (page 49).
The JPEG image file cannot be played.
• The DATA CD is not recorded in ISO 9660 Level 1/Level 2, or Joliet.
• The DATA DVD is not recorded in UDF (Universal Disk Format).
• It has an extension other than “.jpeg” or “.jpg.”
• It is larger than 3,072 (width) × 2,048 (height) in normal mode, or more than
2,000,000 pixels in progressive JPEG image file which is mainly used on
Internet Web sites.
• It does not fit the TV screen (those images are reduced).
• Check the [MEDIA] setting (page 49).
The titles of folder/file/file name are not displayed correctly.
• The system can only display numbers and letters of the alphabet. Other characters are displayed as [*].
Symptom
A disc does not start playing from the beginning.
Remedy
• Program Play, Shuffle Play, or Repeat Play has been selected.
Press CLEAR to cancel these functions before playing a disc.
• Resume Play has been selected.
During stop, press x on the unit or the remote and then start playback
• The title, DVD or PBC menu automatically appears on the TV screen.
• The DVD features an auto playback function.
The system starts playing the disc automatically.
Playback stops automatically.
• Some discs may contain an auto pause signal. While playing such a disc, the system stops playback at the auto pause signal.
You cannot perform some functions such as stop, search,
Slow-motion Play, or Repeat
Play.
• Depending on the disc, you may not be able to perform some of these operations. Refer to the operating instructions supplied with the disc.
Messages do not appear on the
TV screen in the language you want.
• In the Setup Display, select the desired language for the on-screen display in
[OSD] under [LANGUAGE SETUP] (page 53).
The language for the sound track cannot be changed.
• Multilingual tracks are not recorded on the DVD being played.
• The DVD prohibits changing the language for the sound track.
The subtitle language cannot be changed.
• Multilingual subtitles are not recorded on the DVD being played.
• The DVD prohibits changing the subtitles.
The subtitle cannot be turned off. • The DVD prohibits turning off subtitles.
The angles cannot be changed.
• Multi-angles are not recorded on the DVD being played (page 38).
• The DVD prohibits changing the angles.
A disc cannot be ejected and
“LOCKED” appears in the front panel display.
• Contact your Sony dealer or local authorized Sony service facility.
[Data error] appears on the TV screen when playing a DATA
CD or DATA DVD.
The system does not work normally.
• The MP3 file/JPEG image file you want to play is broken.
• The data is not MPEG1 Audio Layer 3 data.
• The JPEG image file format does not conform to DCF.
• The file has the extension “.jpg” or “.jpeg,” but is not in JPEG format.
• Disconnect the AC power cord (mains lead) from the wall outlet (mains), then reconnect after several minutes.
The Control for HDMI function does not work.
• When “HDMI” does not light up in the front panel display, check the HDMI
• Set [CONTROL FOR HDMI] in [HDMI SETUP] to [ON] (page 55).
• Make sure that the connected component is compatible with the [CONTROL
FOR HDMI] function.
• Check that the AC power cord (mains lead) of the connected component is connected securely.
• Check the connected component’s setting for the Control for HDMI function.
Refer to the operating instructions supplied with the component.
• If you change the HDMI connection, connect and disconnect the AC power cord (mains lead), or have a power failure, set [CONTROL FOR HDMI] in
[HDMI SETUP] to [OFF], then set [CONTROL FOR HDMI] in [HDMI
• For details, see “Using the Control for HDMI Function for “BRAVIA” Sync”
87 US
88 US
Symptom
No sound is output from the system and TV while using the
System Audio Control function.
Remedy
• Set [AUDIO (HDMI)] in [HDMI SETUP] to [ON] (page 55).
• Make sure that the connected TV is compatible with the System Audio Control function.
• For details, see “Using the Control for HDMI Function for “BRAVIA” Sync”
The S-AIR function
Symptom Remedy
S-AIR connection is not established (sound transmission is not established), e.g., the indicator of the S-AIR sub unit does the following:
• Turns off.
• Flashes.
• Turns red.
• If you use another S-AIR main unit, place it more than 8 m (about 25 feet) away from the S-AIR main unit you are using.
• Confirm the S-AIR IDs of the unit and S-AIR sub unit (page 67).
• Another S-AIR sub unit is paired to the S-AIR main unit. Pair the desired S-AIR
sub unit with the S-AIR main unit (page 69).
• Place so that the S-AIR main unit and S-AIR sub unit are separated from other wireless devices.
• Avoid using any other wireless devices.
• The S-AIR sub unit is turned off. Make sure the AC power cord (mains lead) is connected and turn on the S-AIR sub unit.
No sound is heard from the
S-AIR sub unit.
• If you use another S-AIR main unit, place it more than 8 m (about 25 feet) away from the S-AIR main unit you are using.
• Confirm the S-AIR IDs of the unit and S-AIR sub unit (page 67).
• Confirm the pairing setting (page 69).
• Place so that the S-AIR main unit and S-AIR sub unit closer together.
• Avoid use of equipment that generates electromagnetic energy, such as a microwave oven.
• Place so that the S-AIR main unit and S-AIR sub unit are separated from other wireless devices.
• Avoid using any other wireless devices.
• Change the “RF CHANGE” setting (page 70).
• Change the S-AIR ID settings of the S-AIR main unit and S-AIR sub unit.
• Turn off the system and S-AIR sub unit, then turn on them.
There is noise or the sound skips. • If you use another S-AIR main unit, place it more than 8 m (about 25 feet) away from the S-AIR main unit you are using.
• Place so that the S-AIR main unit and S-AIR sub unit closer together.
• Avoid use of equipment that generates electromagnetic energy, such as a microwave oven.
• Place so that the S-AIR main unit and S-AIR sub unit are separated from other wireless devices.
• Avoid using any other wireless devices.
• Change the “RF CHANGE” setting (page 70).
• Change the S-AIR ID settings of the S-AIR main unit and S-AIR sub unit.
Self-diagnosis Function
(When letters/numbers appear in the display)
When the self-diagnosis function is activated to prevent the system from malfunctioning, a 5character service number (e.g., C 13 50) with a combination of a letter and 4 digits appears on the TV screen or front panel display. In this case, check the following table.
C:13:50
When the version number appears on the TV screen
When you turn on the system, the version number [VER.X.XX] (X is a number) may appear on the TV screen. Although this is not a malfunction and for Sony service use only, normal system operation will not be possible.
Turn off the system, and then turn on the system again to operate.
VER.X.XX
First 3 characters of the service number
C 13
Cause and/or corrective action
C 31
E XX
(XX is a number)
The disc is dirty.
, Clean the disc with a soft cloth
The disc is not inserted correctly.
, Restart the system, then re-insert the disc correctly.
To prevent a malfunction, the system has performed the selfdiagnosis function.
, Contact your nearest Sony dealer or local authorized Sony service facility and give the 5character service number.
Example: E 61 10
89 US
90 US
Specifications
AUDIO POWER SPECIFICATIONS for the U.S. model
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 3 ohms loads, both channels driven, from 180
- 20,000 Hz; rated 84 watts per channel minimum
RMS power, with no more than 0.7% total harmonic distortion from 250 milli watts to rated output.
Amplifier Section
Surround mode (reference) RMS output power
FL/FR/C/SL/SR*: 144 watts
(per channel at 3 ohms, 1 kHz, 10% THD)
Subwoofer*: 280 watts (at
1.5 ohms, 80 Hz, 10%
THD)
* Depending on the decoding mode settings and the source, there may be no sound output.
Inputs (Analog)
TV/VIDEO (AUDIO IN) Sensitivity: 450/250 mV
AUDIO IN
Inputs (Digital)
Sensitivity: 250/125 mV
TV/VIDEO (COAXIAL IN/OPTICAL IN)
Impedance: 75 ohms/-
Input Stream: Dolby
Digital 5.1ch/DTS 5.1ch/
Linear PCM 2ch
(Sampling Frequency: less than 48 kHz)
Outputs (Analog)
Phones Accepts low- and highimpedance headphones.
Super Audio CD/DVD System
Laser Diode Properties Emission Duration:
Continuous
Laser Output: Less than
44.6
μ
W
* This output is the value measurement at a distance of 200mm from the objective lens surface on the
Optical Pick-up Block with 7mm aperture.
Signal format system NTSC
Tuner Section
System PLL quartz-locked digital synthesizer
FM tuner section
Tuning range
North American models: 87.5 MHz - 108.0 MHz
Other models:
(100 kHz step)
87.5 MHz - 108.0 MHz (50
Antenna (aerial) kHz step)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency 10.7 MHz
AM tuner section
Tuning range
North American, Mexican, and Latin American models:
530 kHz - 1,710 kHz (with the interval set at 10 kHz)
531 kHz - 1,710 kHz (with the interval set at 9 kHz)
European, CIS, and Middle Eastern models:
531 kHz - 1,602 kHz (with the interval set at 9 kHz)
Australian and New Zealand models:
Other models:
531 kHz - 1,710 kHz (with the interval set at 9 kHz)
530 kHz - 1,710 kHz (with the interval set at 10 kHz)
531 kHz - 1,602 kHz (with the interval set at 9 kHz)
530 kHz - 1,610 kHz (with the interval set at 10 kHz)
Antenna (aerial) AM loop antenna (aerial)
Intermediate frequency 450 kHz
Video Section
Outputs VIDEO: 1 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P
B
/C
B
, P
R
/C
R
: 0.7 Vp-p
75 ohms
HDMI OUT: Type A (19 pin)
Speakers
Front (SS-TS95)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Mass (approx.)
Full range Bass reflex
65 mm (2 5
3 ohms
/
8
in) cone type
255 mm × 910 / 940 / 970 /
1000 mm × 255 mm (10 1 /
8 in × 35 7 /
8
/ 37 1 /
8
/ 38 1 /
4
/
39 3 /
8 in × 10 1 /
8 in)
(103 mm × 545 mm × 86 mm (4 1 /
8 in × 21 1 /
2 in ×
3 1 /
2 in) speaker only for reference) (w/h/d)
2.3 kg (5 lb 2 oz)
Center (SS-CT91)
Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Mass (approx.)
Full range Bass reflex,
Magnetically Shielded
65 mm (2 5 /
8
in) cone type
3 ohms
265 mm × 94 mm × 77 mm
(10 1 /
2 in × 3 3 /
4 in × 3 1 /
8 in)
(w/h/d)
0.7 kg (1 lb 9 oz)
Surround (SS-TS92)
S Speaker system
Speaker unit
Rated impedance
Dimensions (approx.)
Mass (approx.)
Full range Bass reflex
65 mm (2 5 /
8
in) cone type
3 ohms
103 mm × 164 mm × 94 mm (4 1 /
8 in × 6 1 /
2 in ×
3 3 /
4 in) (w/h/d)
0.5 kg (1 lb 2 oz)
Subwoofer (SS-WS95)
Speaker system
Speaker unit
Subwoofer Bass reflex
160 mm (6 3 /
8
in) cone type
Rated impedance
Dimensions (approx.)
1.5 ohms
225 mm × 395 mm × 325 mm (8 7 /
8 in × 15 5 /
8 in ×
12 7 /
8 in) (w/h/d)
Mass (approx.) 6.1 kg (14 lb 6 oz)
General
Power requirements
Power consumption
120 V AC, 60 Hz
On: 160 W
Standby: 0.3 W (at the
Power Saving mode)
Output voltage (DIGITAL MEDIA PORT)
DC 5 V
Output current (DIGITAL MEDIA PORT)
Dimensions (approx.)
Mass (approx.)
700 mA
430 mm × 85 mm × 420 mm (17 in × 3 3 /
8 in ×
16 5 /
8 in) (w/h/d) incl. projecting parts
430 mm × 85 mm × 450 mm (17 in × 3 3 /
8 in ×
17 3 /
4 in) (w/h/d) with the wireless transceiver inserted
5.2 kg (11 lb 8 oz)
Wireless transceiver (EZW-RT10/EZW-
RT10A)
Communication system S-AIR Specification
Frequency band
Modulation method
Power requirements
Dimensions (approx.) version 1.0
2.4000 GHz - 2.4835 GHz
DSSS
DC 3.3 V, 350 mA
50 mm × 13 mm × 60 mm
(2 in × 17 /
32
in × 2 3 /
8
in) (w/ h/d)
Mass (approx.)
Supported file format
24 g (1 oz)
MP3 (MPEG 1 Audio Layer-3)
File Extension:
Bitrate:
Sampling frequencies: mp3
32 kbps - 320 kbps
32/44.1/48 kHz
Design and specifications are subject to change without notice.
91 US
92 US
Glossary
Digital Cinema Auto Calibration
Digital Cinema Auto Calibration was developed by Sony to automatically measure and adjust the speaker settings to your listening environment in a short period of time.
Digital Direct Twin Drive Subwoofer
Utilizing Sony proprietary S-master technology, the Digital Direct Twin Drive Subwoofer features two S-master Digital Amplifiers that provide dedicated power to a strategically located subwoofer for astounding sound performance. Easy to set up, Digital Direct Twin
Drive Subwoofer provides a stable sound field over a much larger listening area without having to adjust frequency levels.
Dolby Digital
This movie theater sound format is more advanced than Dolby Surround Pro Logic. In this format, the surround speakers output stereo sound with an expanded frequency range, and a subwoofer channel for deep bass is independently provided. This format is also called “5.1” with the subwoofer channel designed as the 0.1 channel (since it functions only when a deep bass effect is needed). All six channels in this format are recorded separately for superior channel separation. Furthermore, since all the signals are processed digitally, less signal degradation occurs.
Dolby Pro Logic II
Dolby Pro Logic II creates five full-bandwidth output channels from 2 channel sources. This is done using an advanced, high-purity matrix surround decoder that extracts the spatial properties of the original recording without adding any new sounds or tonal colorations.
x Movie mode
The Movie mode is for use with stereo television shows and all programs encoded in Dolby
Surround. The result is enhanced sound field directionality that approaches the quality of discrete 5.1-channel sound.
x Music mode
The Music mode is for use with any stereo music recordings, and provides a wide and deep sound space.
Dolby Surround Pro Logic
As one method of decoding Dolby Surround,
Dolby Surround Pro Logic produces four channels from 2 channel sound. Compared with the former Dolby Surround system, Dolby
Surround Pro Logic reproduces left-to-right panning more naturally and localizes sounds more precisely. To take full advantage of Dolby
Surround Pro Logic, you should have one pair of surround speakers and a center speaker. The surround speakers output monaural sound.
DTS
Digital audio compression technology developed by DTS, Inc. This technology conforms to 5.1-channel surround. This format is comprised of a stereo rear channel and a discrete subwoofer channel. DTS provides the same 5.1 discrete channels of high quality digital audio. The good channel separation is realized due to the all channel data being recorded discretely and processed digitally.
HDMI (High-Definition Multimedia
Interface)
HDMI is an interface that supports both video and audio on a single digital connection, allowing you to enjoy high quality digital picture and sound. The HDMI specification supports HDCP (High-bandwidth Digital
Content Protection), a copy protection technology that incorporates coding technology for digital video signals.
Interlace format
(Interlaced scanning)
The interlace format is the NTSC standard method for displaying TV images at 30 frames per second. Each frame is scanned twice - alternately between the even numbered scanning lines and then odd numbered scanning lines, at
60 times per second.
Parental Control
A function of the DVD to limit playback of the disc by the age of users according to the limitation level in each country. The limitation varies from disc to disc; when it is activated,
playback is completely prohibited, violent scenes are skipped or replaced with other scenes and so on.
Progressive format
(sequential scanning)
In contrast to the interlace format, the progressive format can reproduce 50 - 60 frames per second by reproducing all scanning lines
(525 lines for the NTSC system). The overall picture quality increases and still images, text and horizontal lines appear sharper. This format is compatible with the 525 or 625 progressive format.
S-AIR
(Sony Audio Interactive Radio frequency)
Recent times have seen the rapid spread of DVD media, Digital Broadcasting, and other highquality media.
To ensure that the subtle nuances of these highquality media are transmitted with no deterioration, Sony has developed a technology called “S-AIR” for the radio transmission of digital audio signals with no compression, and has incorporated this technology into the EZW-
RT10/EZW-RT10A/EZW-T100.
This technology transfers digital audio signals with no compression using the 2.4 GHz band range of ISM band (Industrial, Scientific, and
Medical band), also used by wireless LANs and
Bluetooth applications.
Super Audio CD
Super Audio CD is a new high-quality audio disc standard where music is recorded in the
DSD (Direct Stream Digital) format
(conventional CD is recorded in the PCM format). The DSD format, using a sampling frequency 64 times higher than that of a conventional CD, and with 1-bit quantization, achieves both a wide frequency range and a wide dynamic range across the audible frequency range, and so provides music reproduction extremely faithful to the original sound.
x Super Audio CD types
There are two types of discs, depending on the
Super Audio CD layer and CD layer combination.
• Super Audio CD layer: A high-density signal layer for Super Audio CD
• CD layer 1) : A layer that is readable by a conventional CD player
Single layer disc
(a disc with a single Super Audio CD layer)
Super Audio CD layer
Hybrid disc
2)
(a disc with a Super Audio CD layer and a CD layer)
CD layer
3)
Super Audio CD layer
3)
A Super Audio CD layer consists of the 2 channel area or the multi-channel area.
• 2 channel area: An area in which 2 channel stereo tracks are recorded
• Multi-channel area: An area in which multichannel (up to 5.1 channels) tracks are recorded
2 channel area
4)
Multi-channel area
4) Super Audio CD layer
1)
You can play the CD layer on a conventional CD player.
2)
Since both layers are on one side, it is not necessary to turn the disc over.
3)
To select a layer, see “Changing a playback layer for a hybrid Super Audio CD” (page 39).
4)
To select an area, see “Selecting a playback area for a Super Audio CD” (page 39).
93 US
94 US
Playback priority of file types
The table below describes the playback priority of file types under the [MEDIA] setting.
File type
JPEG image files only
Audio files only
Audio files and JPEG image files
[MUSIC/PHOTO]
JPEG image files
Audio files
Audio files and JPEG image files with slide show
[MEDIA] setting
[PHOTO]
JPEG image files
Audio files
JPEG image files
[MUSIC]
JPEG image files
Audio files
Audio files
Language Code List
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
1027 Afar
1028 Abkhazian
1032 Afrikaans
1039 Amharic
1044 Arabic
1045 Assamese
1051 Aymara
1052 Azerbaijani
1053 Bashkir
1057 Byelorussian
1059 Bulgarian
1060 Bihari
1061 Bislama
1066 Bengali;
Bangla
1067 Tibetan
1070 Breton
1079 Catalan
1093 Corsican
1097 Czech
1103 Welsh
1105 Danish
1109 German
1130 Bhutani
1142 Greek
1144 English
1145 Esperanto
1149 Spanish
1150 Estonian
1151 Basque
1157 Persian
1165 Finnish
1166 Fiji
1171 Faroese
1174 French
1181 Frisian
Code Language
1183 Irish
1186 Scots Gaelic
1194 Galician
1196 Guarani
1203 Gujarati
1209 Hausa
1217 Hindi
1226 Croatian
1229 Hungarian
1233 Armenian
1235 Interlingua
1239 Interlingue
1245 Inupiak
1248 Indonesian
1253 Icelandic
1254 Italian
1257 Hebrew
1261 Japanese
1269 Yiddish
1283 Javanese
1287 Georgian
1297 Kazakh
1298 Greenlandic
1299 Cambodian
1300 Kannada
1301 Korean
1305 Kashmiri
1307 Kurdish
1311 Kirghiz
1313 Latin
1326 Lingala
1327 Laothian
1332 Lithuanian
1334 Latvian;
Lettish
1345 Malagasy
Code Language
1347 Maori
1349 Macedonian
1350 Malayalam
1352 Mongolian
1353 Moldavian
1356 Marathi
1357 Malay
1358 Maltese
1363 Burmese
1365 Nauru
1369 Nepali
1376 Dutch
1379 Norwegian
1393 Occitan
1403 (Afan)Oromo
1408 Oriya
1417 Punjabi
1428 Polish
1435 Pashto;
Pushto
1436 Portuguese
1463 Quechua
1481 Rhaeto-
Romance
1482 Kirundi
1483 Romanian
1489 Russian
1491 Kinyarwanda
1495 Sanskrit
1498 Sindhi
1501 Sangho
1502 Serbo-
Croatian
1503 Singhalese
1505 Slovak
1506 Slovenian 1703 Not specified
Parental Control Area Code List
Code Area
2044 Argentina
2047 Australia
2046 Austria
2057 Belgium
2070 Brazil
2079 Canada
2090 Chile
2092 China
2115 Denmark
Code Area
2165 Finland
2174 France
2109 Germany
2248 India
2238 Indonesia
2254 Italy
2276 Japan
2304 Korea
2363 Malaysia
Code Area
2362 Mexico
2376 Netherlands
2390 New Zealand
2379 Norway
2427 Pakistan
2424 Philippines
2436 Portugal
2489 Russia
2501 Singapore
Code Area
2149 Spain
2499 Sweden
2086 Switzerland
2528 Thailand
2184 United
Kingdom
Code Language
1507 Samoan
1508 Shona
1509 Somali
1511 Albanian
1512 Serbian
1513 Siswati
1514 Sesotho
1515 Sundanese
1516 Swedish
1517 Swahili
1521 Tamil
1525 Telugu
1527 Tajik
1528 Thai
1529 Tigrinya
1531 Turkmen
1532 Tagalog
1534 Setswana
1535 Tonga
1538 Turkish
1539 Tsonga
1540 Tatar
1543 Twi
1557 Ukrainian
1564 Urdu
1572 Uzbek
1581 Vietnamese
1587 Volapük
1613 Wolof
1632 Xhosa
1665 Yoruba
1684 Chinese
1697 Zulu
95 US
96 US
Index to Parts and Control
For more information, refer to the pages indicated in parentheses.
Front panel
A
" / 1
B
DISC 1-5 buttons/indicators (36)
C
D
E
F
G
H
I
AUDIO IN/A.CAL MIC jack (24, 29, 72)
J
K
L Z
M
Rear panel
SPEAKER
CENTER SUBWOOFER
TV
DIGITAL IN
OPTICAL COAXIAL
SPEAKER
FRONT R FRONT L SUR R
HDMI OUT
SUR L
DMPORT
DC5V
0.7A MAX
EZW-RT10
COMPONENT VIDEO OUT VIDEO
OUT
TV/VIDEO
Y P B /C B P /C R R AUDIO IN L
ANTENNA
FM
COAXIAL 75
AM
A
B
C COAXIAL 75 Ω FM
D
E
TV/VIDEO (AUDIO IN R/L) jacks (23)
F
G
H DMPORT (DIGITAL MEDIA PORT) jack
I
J TV/VIDEO (DIGITAL IN COAXIAL/
97 US
98 US
Front panel display
About the indications in the front panel display
A Playing status
B Flashes when the sleep timer is set.
C Displays the system’s status such as chapter, title, or track number, time information, radio frequency, playing status, decoding mode, etc.
D Lights up when a station is received.
E Stereo/Monaural effect (Radio only)
F Lights up when the S-AIR transceiver is inserted in the unit and the system
G Lights up when the HDMI OUT jack is correctly connected to HDCP (Highbandwidth Digital Content Protection) compliant device with HDMI or DVI
(Digital Visual Interface) input. (22)
H Current surround format (Except for
JPEG image file)
I Lights up when a Super Audio CD/CD
Remote control
A – O
ALPHABETICAL ORDER
P – Z
ANGLE 3
AUDIO qh
CLEAR es
D.TUNING ws
DISC SKIP ed
DISPLAY wa
DVD MENU wg
DVD TOP MENU qd
DYNAMIC BASS 6
ENTER wf
FUNCTION +/– 2
MENU wg
MUTING 7
NIGHT wd
ONE-TOUCH PLAY eg
PICTURE NAVI qg
PRESET +/– wj
S-AIR MODE 4
SLEEP qj
SOUND MODE 5
SUBTITLE ws
SYSTEM MENU wf
THEATER qk
TOOLS wh
TUNING +/– 0
TV wl
TV CH +/– wj
TV INPUT w;
TV VOL +/– ef
VOLUME +/– 8
BUTTON DESCRIPTIONS
Number buttons qf
[ / 1 (on/standby) 1
TV [ / 1 (on/standby) ql
C / X / x /
c / qs
REPLAY/ADVANCE
9
.
/ > wj
m / M 0
STEP / 9
SLOW / 0
H (play) e;
x (stop) wk
X (pause) qa
DISPLAY* wh
O RETURN ea
es
* This button is available for the “DVD” or “DMPORT” function. Depending on the
DIGITAL MEDIA PORT adapter, this button may not work.
99 US
100 US
Guide to the Control Menu Display
You can use the Control Menu display to select a function and to view related information.
DISPLAY
Each time you press DISPLAY, the Control Menu display changes:
1 t 2 t ... t 1 t ...
1 Control Menu display 1
2 Control Menu display 2 (appears when available)
3 Control Menu display off
Note
• The Control Menu Display appears during the “DVD” function.
Control Menu display
The Control Menu display 1 and 2 will show different items depending on the disc type. For details, see the pages in parentheses.
Example: Control Menu display 1 when playing a DVD VIDEO.
Control Menu items
Selected item
Function name of selected
Control Menu item
Currently playing title number
Currently playing chapter number
Total number of titles
Total number of chapters
Playback status
( N Playback,
X Pause, x Stop, etc.)
9 8 ( 9 9 )
1 3 ( 9 9 )
T 0 : 0 4 : 1 7
OFF
OFF
ALL DISCS
ONE DISC
TITLE
CHAPTER
DVD VIDEO
Type of disc being played
Playing time
Current setting
Options
REPEAT
ENTER
Quit:
DISPLAY
Operation message
To turn off the display
List of Control Menu items
Item Item Name, Function, Relevant Disc Type
[TITLE] (page 44)/[SCENE] (page 44)/[TRACK] (page 44)
You can select the title, scene, or track to be played.
[CHAPTER] (page 44)/[INDEX] (page 44)
You can select the chapter or index to be played.
You can display the index and select the index to be played.
You can select the track to be played.
[ORIGINAL/PLAY LIST] (page 44)
You can select the type of titles (DVD-RW/DVD-R) to be played, the [ORIGINAL] one, or an edited [PLAY LIST].
You can check the elapsed time and the remaining playback time.
You can play from a desired point by inputting the time code (DVD VIDEO/DVD-VR only).
You can select the playback area on a Super Audio CD when available.
[SUPER AUDIO CD/CD LAYER] (page 39)
You can select the playback layer on a Super Audio CD when available.
You can select the track to play in the order you want.
101 US
102 US
You can play the tracks/files in random order.
You can play all discs repeatedly, the entire disc (all titles/all tracks/all folders/all files) repeatedly, or one title/chapter/track/folder/file repeatedly.
You can adjust the delay between the picture and sound.
You can display the DVD’s menu.
You can display the list of folders/JPEG image files.
You can make the basic adjustments. Use Quick Setup to select the desired language of the on-screen display, the aspect ratio of the TV, and select yes or no to start the Auto Calibration.
[CUSTOM]
In addition to the Quick Setup setting, you can adjust various other settings.
You can select the folder to be played.
You can select the JPEG image file to be played.
You can display the date the picture was taken by a digital camera.
You can select the duration for which the slides are displayed on the TV screen.
You can select the effects to be used for changing slides during a slide show.
You can select the data type (MP3 file, JPEG image file, or both MP3 file and JPEG image file) to be played on a DATA CD/DATA DVD.
Tip
• The Control Menu icon indicator lights up in yellow t when you select any item except [OFF]
([PROGRAM], [SHUFFLE], [REPEAT], and [A/V SYNC] only). The [ORIGINAL/PLAY LIST] indicator lights up in yellow when you select [PLAY LIST] (default setting). The [MULTI/2CH] indicator lights up in yellow when you select the multi-channel playback area on a Super Audio CD.
Index
Numerics
A
B
C
D
E
F
H
HDMI
YC B C R
I
J
L
M
N
O
P
Q
R
S
T
V
103 US
Sony Corporation Printed in China
(1)

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- 5.1 channel surround sound
- HDMI output
- DIGITAL MEDIA PORT
- S-AIR function
- MP3 and JPEG playback
- Auto calibration