APPLICANT: TOSHIBA CORPORATION

9155GPX

OWNER'S MANUAL

Draft

December 2001

TABLE OF CONTENTS

SAFETY INFORMATION FOR

WIRELESS HANDHELD PHONES ...........…………........... 1

SAR INFORMATION ......................................…………....... 2

FUNCTIONS .............................................…………............. 3

GETTING STARTED ................................…………............. 5

BASIC OPERATION .......................................…………....... 6

Placing Calls .......................................………….............. 6

Receiving Calls ................................…………................. 8

During Calls..........................................…………............. 9

Standby.................................................…………............. 11

OPERATING PROCEDURES ........................…………....... 12

TRANSCEIVER TYPE: CJ6DCE45380A

EXHIBIT Type “User Manual”

Read this information before using your handheld portable Cellular Telephone.

Your wireless handheld portable telephone is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) signals.

FCC RF EXPOSURE INFORMATION

In August 1996, the Federal Communications Commission (FCC) of the United States, with its action in Report and Order FCC 96-326, adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this phone complies with the FCC guidelines and these international standards.

Use only the supplied or an approved antenna. Unauthorized antennas, damaged antennas, modifications, or attachments could impair call quality, damage the phone, or result in violation of FCC regulations. Please contact your local dealer for replacement antenna.

Body-worn Operation

This device was tested for typical body-worn operations with the BC-9100 belt-clip and LB-9100 holster models, offered by Audiovox as an accessory to this phone, and found to comply with FCC RF exposure requirements. Third-party belt-clips, holsters and similar accessories should be avoided, as they have not been tested and may not comply with FCC RF exposure limits.

For more information about RF exposure, please visit the FCC website at www.fcc.gov .

1

THIS MODEL PHONE MEETS THE GOVERNMENT’S RE-

QUIREMENTS FOR EXPOSURE TO RADIO WAVES.

Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government.

These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population.

The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.

The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg.

* Tests for

SAR are conducted with the phone transmitting at its highest certified power level in all tested frequency bands. Although the

SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.

Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model phone when tested for use at the ear is

1.45

W/kg and when worn on the body, as described in this user guide, is

0.72

W/kg. (Body-worn measurements differ among phone models, depending upon available accessories and FCC requirements). While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement for safe exposure.

The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/ oet/fccid after searching on FCC ID CJ6DCE

45380

A.

Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications & Internet Association (CTIA) web-site at http://phonefacts.net.

* In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements.

2

External View

Retractable

Whip Antenna

Power

Indicator

Receiving

Signal

Strength

Indicator

Digital

Mode

Indicator

IN USE

Indicator

Roaming

Indicator

Message

Indicator

Vibrating

Indicator

Battery Level

Indicator

Soft Key 1

Send Key

Message

Access Key

Voice Mail &

Speakerphone

One-Touch

Emergency Key

Digit Keys

Rm

ABCDEFGHIJKL

MNOPQRSTUVWX

YZ1234567890

Rc l F

V

1

4

GHI

7

PQRS

2

ABC

5

JKL

8

TUV

0

CLR

3

DEF

6

MNO

9

WXYZ

Vibrating &

Shift Key

Next Key

Power/Data

Connector

Earpiece

Incoming Call

& Charging

Indicator (LED)

Earphone

Mic Jack

Graphic

Display

Soft Key 2

End Key with

Power On/Off

Multi Function

Key

Up-arrow

Recall

Function

Down-arrow

Clear Key

Voice Activated

Dialing &

Space Key

Microphone

3

Function of Keys

Digit Keys

1

2

ABC

3

DEF

4

GHI 5

JKL

6

MNO

7

PQRS

8

TUV

9

WXYZ

0

To enter Telephone Numbers.

To enter letters and symbols (see page 32).

1 is also used for One-Touch

Emergency feature.

Function Keys

Rc l F

V

CLR

Soft Keys. To function as shown in the bottom line on the display.

SEND Key. To originate or answer a call.

Rc l

V

F

CLR

END Key. To terminate a call and to turn the phone ON/OFF.

To recall phone numbers from memory.

Also used as left-arrow key.

To be used with other keys to activate various special features. Also used as right-arrow key.

To control the volume of Ringer, Key Tone and Earpiece/Speakerphone.

Also used as up/down-arrow keys.

To access your Voice Mail with only one key (see page 62) and to activate Speakerphone mode (see page 29).

To review Text Messages or to learn how many Voice Messages are in your Voice

Mailbox (see page 57).

To clear digits from the display or from a memory location.

LCD Display Indication

Items Descriptions

Receiving Signal Strength Indicator.

The number of lines indicates the received

Signal Strength, and is also used as a

POWER ON Indicator.

Digital Mode Indicator. To indicate the phone is operating in digital mode.

A call is in progress.

The phone is out of Service Area.

Rm The phone is out of the Home Area.

Message Indicator. To indicate that new

Text Messages are stored in memory or new

Voice Messages are in your Voice Mailbox.

Vibrating Indicator. To indicate that the vibrating alert is active.

Battery Level Indicator.

Monitors the battery charge condition.

ABCDEFGHIJKL

MNOPQRSTUVWX

YZ1234567890

Graphic full-dot matrix display with flexible font size in 3 to 7 lines.

4

Turning the Phone On/Off

Press and hold . All the indicators and the display will light momentarily, and a tone will be heard. The indicator will be displayed while the phone is on.

To turn the phone off, press and hold .

Antenna Position

The antenna can be used in its fully extended or fully retracted position only. It is recommended that the antenna should be fully extended for optimum performance and signal strength or while operating in poor signal areas.

Receiving Signal Strength Indicator ( )

The number of lines shown by this icon indicates the strength of the signal your phone is receiving. Four lines indicates maximum signal strength. The number of lines may change as you move with the phone to represent the changing signal strength. If the signal is not strong enough to place a call, “ ” will appear on the display.

Battery Level Indicator

You can always monitor the battery charge condition with the constant battery level indicator. The number of blocks indicates the battery conditions as follows:

Full charge

Low charge

Flashing indicates discharged.

5

Placing Calls

To Place a Call

1. Enter the phone number.

(A maximum of 32 digits will be displayed.)

123-456-7890

STO Menu

2. Press .

The indicator will appear on the display.

Calling...

123-456-7890

• To Correct a Number

Press

CLR

to clear the last digit.

Press and hold

CLR

to erase all the digits entered.

• If the Call Fails to Go Through

Press and to redial the number.

To Terminate a Call

Press . The indicator will no longer appear in the display.

Last Number Redial

1. Press the key under Redial , or press

Rcl

to recall the last number dialed.

2. Press to place the call.

See Call History on page 54 for details. See also Re-

dial Soft Key (F04) on page 89.

To Dial the Last Number Received

Press

Rcl

to recall the last number with Caller ID you received, then press .

See Call History on page 54 for details.

Phonebook Dialing

Press

Rcl

and enter an address (01 to 99) to recall a number from your phonebook, then press .

See Phonebook Recall on page 43 for details.

Tip: The V key will be used for Voice Mail access. See page 62.

Tip: Press and hold page 53.

for Voice Activated Dialing. See

6

Speed Dialing

If you know the phonebook address of the telephone number that you want to call, you may place a call without using

Rcl

.

1. Enter the one or two digits of your Phonebook address (1 to 9 or 10 to 99).

2. Press . The phone number will be displayed.

The indicator will be displayed and the call will be placed.

Note: If two telephone numbers are stored in the address, the Primary Number will be dialed.

Quick Dialing

When this feature is on, the Primary number in your

Phonebook address 02 to 09 can be dialed with just one push of the key. See Quick Dialing (F01) on page

89 to turn this feature on/off.

1. Press a digit key ( 2

ABC

to 9

WXYZ

) for more than one second.

2. The number in your phonebook is automatically dialed. The phone number will be displayed. The

indicator will light.

Note: The key 1 is not for Quick Dialing, but for One-

Touch Emergency Call, page 27.

Emergency Call

This feature permits you to place an emergency call even if your telephone is in “Phone Lock”, “Keypad Lock” or

“Restrict” mode. Up to 3 numbers can be programmed as

Emergency numbers. The emergency numbers “911” and

“ 911” are already preprogrammed. See To Change

Emergency Numbers (F62) on page 85.

Example: To Call 911 in “Phone Lock” or “Key-

pad Lock” mode.

1. Enter 9

WXYZ

1 1 . The “911” will not be displayed.

2. Press .

Calling...

The “911” will be displayed.

The indicator will light, and the call will be placed.

Emergency

911

7

One-Touch Emergency Call

This feature permits you to dial an emergency number by a single key stroke, even in the “Phone Lock” or

“Restrict” mode. This feature can be turned off to prevent unintentional calls to the emergency number.

See To Turn On/Off One-Touch Emergency Call Fea-

ture (F63) on page 85.

1. Press and hold 1 for more than 2 seconds. The number in emergency memory location “1” will be dialed.

2. Then the indicator will be displayed and the call will be placed. (The factory preset number is

“911”.)

Note: This feature cannot be used if the Keypad Lock is on.

You need to dial all the digits and .

Emergency Call Mode

When you dial one of the 3 preprogrammed emergency numbers, your phone will enter the Emergency Call

Mode. In this mode, the phone will attempt to complete the emergency call using any available cellular system from which it can obtain service.

After it places an emergency call, the phone will stay in the Emergency Call Mode, and will display “Emer-

gency Call Mode, END to exit”. In the Emergency Call

Mode, the phone will attempt to continue to receive service from the Cellular system that it used to complete the call. The phone will automatically exit the

Emergency Call Mode after 5 minutes or after you press .

Receiving Calls

The phone sounds an alert or vibrates to alert you of an incoming call. The phone sounds an alert or vibrates to alert you of an incoming call. Also, the LED on the top of the phone will flash.

To Receive a Call

When the telephone rings, press to answer the call.

The indicator will be displayed.

Note: To mute the ringer or stop the vibrating, press .

Any Key Answering

This feature permits you to answer an incoming call by pressing any key on the key pad except and Rcl F .

8

Caller ID with Name

This feature allows you to preview in your display the number and name of the party calling you before you answer the call. The name is as you programmed it in your phonebook.

1. When the phone rings, the

Incoming Call

Calling Number appears in the display.

JACK

123-456-7890

2. The last 10 Caller IDs are stored in the memory for your review and redial. See Call History on page 54 for details.

Note: “Number Restricted” or “Number Unavailable” is displayed when the Caller ID is restricted or not available.

Automatic Calls-in-Absence Indicator

This feature indicates the number of unanswered incoming calls. The display indicates “Called XX”, the number of calls (01 to 99) you missed and the LED will blink.

It also indicates the caller number and name of the latest call, if available. Press the key under Refer to view In-

coming Call History.

Depressing any key will clear the display. See Redial Soft Key

(F04) on page 89.

Called 12

May 21 10:25 am

JACK

123-456-7890

Refer

Ringing Tone with Melody

The

9155GPX

offers you 15 styles of ringer tones and melodies for alerting incoming calls. Ringer volume can also be adjusted. See Ringer Type Selection (F32) on page 75 and Ringer Volume Control (F31) on page 75 for setting. See also Vibrating Alert (F8) on page 88.

Distinctive Ringing (Audible Caller ID)

You may program different ringer styles for different phonebook addresses. See To Store a Ringer Type

with the Phone Number on page 40 for setting.

During Calls

To Adjust the Earpiece Volume

Simply press or to ad-

Ear/SPK Vol.

just Earpiece/Speakerphone

Volume during a call.

9

To Mute a Phone Conversation

There are two ways to mute the microphone during a call.

1. Press the key under Mute , or press

F F

.

2. Then the screen displays “Phone is muted!”.

3. To return to normal mode, press the key under

Unmute , or press

F F

again.

Note: Terminating a call cancels the muting.

Speakerphone Mode (Two-Way)

This feature allows you to engage in a conversation without having to hold the phone.

1. To activate this feature, press V during a call.

The screen displays “Speaker ON!”.

2. Press or erphone volume.

to adjust the earpiece/speak-

3. To return to normal mode, press V again.

Notes: 1. Terminating a call cancels the speakerphone mode.

2. It is not recommended to use this feature in a noisy environment.

Automatic Talk Timer

The talk time of the current call will be automatically displayed. For example, “1H 23M 45S”.

Scratch Pad Dialing

If you enter a telephone number during a call, the number will be stored in the Scratch Pad memory.

After terminating the call, the number you entered can be dialed by pressing .

Note: You can deactivate “Sending DTMF” so that keypad tones will not be transmitted to the calling party. See

Sending DTMF (F34) on page 75.

Call Waiting

Your service provider may provide Call Waiting service.

When you are on a call, you may hear a beep tone alerting you of another incoming call.

Your phone displays “New Caller” and the new caller’s name and number. The name is as you programmed it in your phonebook.

1. Press to answer the new call.

2. Press again to switch between the two calls.

10

Three-Way Calling

Your service provider may provide Three-Way Calling service. When a call is already in progress, you may call the third party.

1. Enter a number and press to call the third party.

2. Press again to connect all three parties.

Ask your service provider for the detailed information.

Standby

Indicators on Standby

Your phone displays date and time, various settings status, and soft keys in standby.

May 21 Mon

3 : 15 pm

Redial Web

: Ringer Volume is in Silent mode. See page 75.

: Automatic Answering is active. See page 89.

: Phone Lock is active. See page 72.

: Keypad Lock is active. See page 71.

: Countdown Timer is active. See page 80.

: Clock Alarm is active. See page 79.

Redial : See Last Number Redial on page 25.

Web : See Accessing Internet on page 65.

Note: For displaying date and time, see Clock Indicator (F42) and Clock Adjustment (F43) on page 79.

Vibrating Alert

To activate Vibrating Alert, press and hold . The

indicator will be displayed. To deactivate it, press and hold page 88.

again. See also Vibrating Alert (F8) on

Multilingual

Your phone provides multiple languages (English, Spanish, French and Portuguese) for displaying the menus and prompts in the Basic Operation, Phonebook Operation and Function Menu. See Language Selection

(F24) on page 74.

11

Never violate any of the following Rules and Regulations of the FCC when using your Cellular Phone. Such violations are punishable by fine, imprisonment or both.

• Never use obscene, indecent, or profane language.

• Never use your Cellular Phone to send false distress calls.

• Never wiretap or otherwise intercept a phone call, unless you have first obtained the consent of the parties participating in the call.

• Never make any anonymous calls to annoy, harass, or molest other people.

• Never charge another account without authorization, to avoid payment for service.

• Never willfully or maliciously interfere with any other radio communications.

• Never refuse to yield the line when informed that it is needed for an Emergency Call. Also, never take over a line by stating falsely that it is needed for an emergency.

12