MQ Multiquip MVC88VGH-VGHW Plate Compactor Operation Manual

OPERATION AND PARTS MANUAL
SERIES
MODEL MVC-88VGH/VGHW
ONE-WAY PLATE COMPACTOR
(HONDA GASOLINE ENGINE)
Revision #2 (08/06/10)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
MVC-88VGH/VGHW PLATE COMPACTOR — PROPOSITION 65 WARNING
l
PAGE 2 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
NOTES
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 3
MVC-88VGH/VGHW PLATE COMPACTOR — TABLE OF CONTENTS
Multiquip —MVC88VGH/VGHW Honda GX160U1QMX2 Engine
Cylinder Head Assembly ....................................38-39
Plate Compactor
Proposition 65 Warning ............................................. 2
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Safety Information ................................................ 6-10
Specifications (Compactor/Engine) ........................ 11
General Information ................................................ 12
Components (Plate Compactor) ............................. 13
Components (Engine) ............................................. 14
Inspection ........................................................... 15-16
Initial Start-Up .................................................... 17-18
Operation ................................................................ 18
Maintenance ...................................................... 19-21
Preparation For Long Term Storage ....................... 22
Troubleshooting (Engine) ................................... 23-24
Troubleshooting (Plate Compactor) ........................ 24
Explanation Of Codes In Remarks Column ............ 26
Suggested Spare Parts ........................................... 27
Cylinder Barrel (Recoil) Assembly .....................40-41
Crankcase Cover Assembly ...............................42-43
Crankshaft Assembly .........................................44-45
Piston/Rings Assembly.......................................46-47
Camshaft Assembly ...........................................48-49
Recoil Starter .....................................................50-51
Fan Cover Assembly ..........................................52-53
Carburetor Assembly .........................................54-55
Air Cleaner Assembly.........................................56-57
Muffler Assembly ...............................................58-59
Fuel Tank Assembly ...........................................60-61
Cooling Fan & Flywheel Assembly .....................62-63
Ignition Coil Assembly ........................................64-65
Control Assembly ...............................................66-67
Terms and Conditions Of Sale — Parts .................. 68
Component Drawings
Nameplate and Decals....................................... 28-29
Body Assembly .................................................. 30-31
Vibrator Assembly .............................................. 32-33
Sprinkler Assembly (Option) .............................. 34-35
Transport Wheel Assembly (Option) .................. 36-37
l
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
www.multiquip.com
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Order via Internet (Dealers Only):
Best Deal!
Effective:
January 1st, 2006
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
Order parts on-line using Multiquip’s SmartEquip website!
N View Parts Diagrams
N Order Parts
N Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Goto www.multiquip.com and click on
Order Parts to log in and save!
Note: Discounts Are Subject To Change
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Note: Discounts Are Subject To Change
Order via Phone: Domestic (US) Dealers Call:
1-800-427-1244
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
When ordering parts, please supply:
R
R
R
R
R
R
Dealer Account Number
Dealer Name and Address
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
Quantity, Part Number and Description of Each Part
R
Specify Preferred Method of Shipment:
UPS/Fed Ex
DHL
N Priority One
Truck N Ground
N Next Day
N Second/Third Day
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 5
MVC-88VGH/VGHW PLATE COMPACTOR — SAFETY INFORMATION
Do not operate or service the equipment before reading
the entire manual. Safety precautions should be followed
at all times when operating this equipment.
Failure to read and understand the safety
messages and operating instructions could
result in injury to yourself and others.
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.
SAFETY MESSAGES
The four safety messages shown below will inform you
about potential hazards that could injure you or others. The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
DANGER, WARNING, CAUTION or NOTICE.
SAFETY SYMBOLS
DANGER
Indicates a hazardous situation which, if not avoided,
WILL result in DEATH or SERIOUS INJURY.
WARNING
Indicates a hazardous situation which, if not avoided,
COULD result in DEATH or SERIOUS INJURY.
CAUTION
Indicates a hazardous situation which, if not avoided,
COULD result in MINOR or MODERATE INJURY.
NOTICE
Addresses practices not related to personal injury.
l
PAGE 6 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW PLATE COMPACTOR — SAFETY INFORMATION
GENERAL SAFETY
CAUTION
„ NEVER operate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
„ NEVER operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
„ NEVER operate this equipment under the influence of
drugs or alcohol.
„ ALWAYS check the equipment for loosened threads or
bolts before starting.
„ DO NOT use the equipment for any purpose other than
its intended purposes or applications.
NOTICE
„ This equipment should only be operated by trained and
qualified personnel 18 years of age and older.
„ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
„ Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
„ NEVER use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
„ ALWAYS know the location of the nearest
fire extinguisher.
„ ALWAYS know the location of the nearest
first aid kit.
„ ALWAYS know the location of the nearest phone or keep
a phone on the job site. Also, know the phone numbers
of the nearest ambulance, doctor and fire department.
This information will be invaluable in the case of an
emergency.
„ ALWAYS clear the work area of any debris, tools, etc.
that would constitute a hazard while the equipment is
in operation.
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 7
MVC-88VGH/VGHW PLATE COMPACTOR — SAFETY INFORMATION
COMPACTOR SAFETY
DANGER
„ NEVER operate the equipment in an explosive
atmosphere or near combustible materials. An
explosion or fire could result causing severe
bodily harm or even death.
WARNING
„ NEVER disconnect any emergency or safety devices.
These devices are intended for operator safety.
Disconnection of these devices can cause severe injury,
bodily harm or even death. Disconnection of any of these
devices will void all warranties.
CAUTION
„ NEVER lubricate components or attempt service on a
running machine.
NOTICE
„ ALWAYS keep the machine in proper running condition.
„ Fix damage to machine and replace any broken parts
immediately.
„ ALWAYS store equipment properly when it is not being
used. Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel.
ENGINE SAFETY
DANGER
„ The engine fuel exhaust gases contain poisonous carbon
monoxide. This gas is colorless and odorless, and can
l
cause death if inhaled.
„ The engine of this equipment requires an adequate
free flow of cooling air. NEVER operate this equipment
in any enclosed or narrow
area where free flow of the
air is restricted. If the air
flow is restricted it will cause
injury to people and property
and serious damage to the
equipment or engine.
WARNING
„ DO NOT place hands or fingers inside engine
compartment when engine is running.
„ NEVER operate the engine with heat shields or
guards removed.
„ Keep fingers, hands hair and clothing away
from all moving parts to prevent injury.
„ DO NOT remove the radiator cap while the
engine is hot. High pressure boiling water will gush out
of the radiator and severely scald any persons in the
general area of the compactor.
„ DO NOT remove the coolant drain plug
while the engine is hot. Hot coolant will
gush out of the coolant tank and severely
scald any persons in the general area of
the compactor.
„ DO NOT remove the engine oil drain plug while the
engine is hot. Hot oil will gush out of the oil tank and
severely scald any persons in the general area of the
compactor.
CAUTION
„ NEVER touch the hot exhaust manifold,
muffler or cylinder. Allow these parts to cool
before servicing equipment.
NOTICE
„ NEVER run engine without an air filter or with a dirty air
filter. Severe engine damage may occur. Service air filter
frequently to prevent engine malfunction.
„ NEVER tamper with the factory settings
of the engine or engine governor. Damage
to the engine or equipment can result
if operating in speed ranges above the
maximum allowable.
„ NEVER tip the engine to extreme angles during lifting as
it may cause oil to gravitate into the cylinder head, making
the engine start difficult.
PAGE 8 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW PLATE COMPACTOR — SAFETY INFORMATION
FUEL SAFETY
BATTERY SAFETY (ELECTRIC START ONLY)
DANGER
DANGER
„ DO NOT add fuel to equipment if it is placed inside truck
bed with plastic liner. Possibility exists of explosion or
fire due to static electricity.
FUEL
„ DO NOT drop the battery. There is a possibility that the
battery will explode.
„ DO NOT expose the battery to open flames,
sparks, cigarettes, etc. The battery contains
combustible gases and liquids. If these
gases and liquids come into contact with a
flame or spark, an explosion could occur.
WARNING
FUEL
„ ALWAYS wear safety glasses when
handling the battery to avoid eye irritation.
The battery contains acids that can cause
injury to the eyes and skin.
„ Use well-insulated gloves when picking up
the battery.
„ DO NOT start the engine near spilled fuel or combustible
fluids. Diesel fuel is extremely flammable and its vapors
can cause an explosion if ignited.
„ ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
„ ALWAYS use extreme caution when working with
flammable liquids.
„ DO NOT fill the fuel tank while the engine is running
or hot.
„ DO NOT overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or sparks from
the ignition system.
„ Store fuel in appropriate containers, in well-ventilated
areas and away from sparks and flames.
„ NEVER use fuel as a cleaning agent.
„ DO NOT smoke around or near the
equipment. Fire or explosion could result
from fuel vapors or if fuel is spilled on a
hot engine.
„ ALWAYS keep the battery charged. If the battery is not
charged, combustible gas will build up.
„ DO NOT charge battery if frozen. Battery can explode.
When frozen, warm the battery to at least 61°F (16°C).
„ ALWAYS recharge the battery in a well-ventilated
environment to avoid the risk of a dangerous concentration
of combustible gases.
„ If the battery liquid (dilute sulfuric acid)
comes into contact with clothing or skin,
rinse skin or clothing immediately with
plenty of water.
„ If the battery liquid (dilute sulfuric acid) comes into
contact with eyes, rinse eyes immediately with plenty
of water and contact the nearest doctor or hospital to
seek medical attention.
CAUTION
„ ALWAYS disconnect the NEGATIVE battery terminal
before performing service on the equipment.
„ ALWAYS keep battery cables in good working condition.
Repair or replace all worn cables.
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 9
MVC-88VGH/VGHW PLATE COMPACTOR — SAFETY INFORMATION
TRANSPORTING SAFETY
CAUTION
„ NEVER allow any person or animal to stand underneath
the equipment while lifting.
NOTICE
„ Before lifting, make sure that the equipment parts (hook
and vibration insulator) are not damaged and screws are
not loose or missing.
„ Always make sure crane or lifitng device has been
properly secured to the lifting bail (hook) of the
equipment.
„ ALWAYS shutdown engine before transporting.
„ NEVER lift the equipment while the engine is running.
„ Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
„ Use adequate lifting cable (wire or rope) of sufficient
strength.
„ Use one point suspension hook and lift straight
upwards.
„ DO NOT lift machine to unnecessary heights.
„ ALWAYS tie down equipment during transport by
securing the equipment with rope.
ENVIRONMENTAL SAFETY
NOTICE
„ Dispose of hazardous waste properly.
l
Examples of potentially hazardous
waste
are used motor oil, fuel and fuel filters.
„ DO NOT use food or plastic containers to dispose of
hazardous waste.
„ DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
PAGE 10 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW PLATE COMPACTOR — SPECIFICATIONS
TABLE 1. Specifications (Compactor)
Models
MVC-88VGH/MVC-88VGHW
Centrifugal Force
3,450 lbs. (1,564.9 kg)
Number of Vibrations
5,800 vibrations/min
Traveling Speed
56 ft./min (17 meters/min)
Plate Size (LxW)
19.7 x 20.7 in.
.500 x .525 mm
Operating Weight (VGH)
Operating Weight (VGHW)
196 lbs. (89.0 kg.)
217 lbs. ( 98.5 kg.)
Fuel Tank Capacity
3.8 qt. (3.6 liters)
Water Tank Capacity
VGHW Model Only
13.7 qt. (13.0 liters)
Max. Area Of Compaction
5800 sq. ft./hr.
Table 2. Specifications (Engine)
Model
Type
HONDA GX160U1QMX2
Air-cooled 4 stroke, Single
Cylinder, OHV, Horizontal
Shaft Gasoline Engine
Bore X Stroke
2.7 in. x 1.8 in.
(68 mm x 45 mm)
Displacement
163 cc (9.9 cu-in)
Max Output
5.5 H.P./3600 R.P.M.
Engine
Fuel Tank Capacity
Fuel
Lube Oil Capacity
Speed Control Method
Star ting Method
Dry Net Weight
Approx. 0.95 U.S. gallons
(3.6 liters)
Unleaded Automobile
Gasoline
.60 liters (0.63 qts)
Centrifugal Fly-weight
Type
Recoil Star t
33 lbs (15 Kg.)
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 11
MVC-88VGH/VGHW PLATE COMPACTOR — GENERAL INFORMATION
Definition of Plate Compactor
The Mikasa MVC-88VGH/VGHW is a walk behind, plate
compactor designed for the compaction of sand, mixed soils
and asphalt. This plate compactor is a powerful compacting tool
capable of applying a tremendous force in consecutive high
frequency vibrations to a soil surface. Its applications include
compacting for road, embankments and reservoirs as well as
backfilling for gas pipelines, water pipelines and cable installation
work.
Vibratory Plates
The vibratory plates of the MVC-88GH/GHW produce low
amplitude high frequency vibrations, designed to compact
granular soils and asphalt.
The resulting vibrations cause forward motion. The engine and
handle are vibration isolated from the vibrating plate.
Frequency/Speed
The compactor's vibrating plate has a frequency range between
5800 vpm (vibrations per minute). The travel speed of the
compactor is approximately 17 meters/minute (56 ft./minute).
Engine
The Mikasa MVC-88VGH/VGHW Plate Compactor is equipped
with a Honda GX160U1QMX2 air cooled, 4-cycle gasoline
engine. The engine drives an eccentric weight at a high speed
to develop a compaction force. In addition this engine is equipped
with an Oil Alert system that will automatically stop the engine
before the engine falls below safe engine oil operating limits.
Always be sure to check the engine oil level prior to starting
the engine.
Controls
Before starting the MVC-88VGH/VGHW Plate Compactor identify
and understand the function of the controls and components.
l
PAGE 12 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW PLATE COMPACTOR — COMPONENTS (COMPACTOR)
Figure 1. Plate Compactor Controls
Figure 1 shows the location of the basic controls and components
of the MVC-88VGH/VGHW Plate Compactor. The function of
each control is described below:
6.
Belt Cover – Remove this cover to gain acess to the V-belts.
NEVER run the compactor without the V-belt cover. If the Vbelt cover is not installed, the possibility exists that your
hand may get caught between the V-belt and clutch, causing
serious injury and bodily harm.
1.
Water Tank Cap (VGHW Only) – Remove this cap to add
water to the water tank.
2.
Fuel Tank Cap – Remove this cap to add fuel.
7.
3.
Lifting Bale – When lifting of the compactor is required
either by forklift, crane etc., tie rope or chain around this
lifting point.
Vibrating Plate – A flat, open plate made of durable cast
iron construction used in the compacting of soil.
8.
Vibration Case – Encloses the eccentric, gears and
counter weights.
4.
Handle Bar – When operating the compactor use this
handle bar to manuever the compactor.
9.
Water Tube (Sprinkler) – Supplies water to the soil via a
splash plate.
5.
Gasoline Engine – This plate compactor uses a HONDA
GX160U1QMX2 engine. Refer to the HONDA owner's
manual for engine information and related topics.
10. Water Shut-Off Valve – Turn this valve downward to let
water flow from the water tank to the water tube.
11. Water Tank (VGHW only) – Holds 13.7 quarts of water
(removable, no tools required).
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 13
MVC-88VGH/VGHW PLATE COMPACTOR — COMPONENTS ( ENGINE)
Figure 2. Engine Controls & Components
ENGINE COMPONENTS
5.
The engine (Figure 2) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.
Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
6.
Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
1.
7.
Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
DANGER
Explosive
Fuel Hazard
NOTE
Adding fuel to the tank should be done only when
l an opportunity
the engine is stopped and has had
to cool down. In the event of a fuel spill, DO NOT
attempt to start the engine until the fuel residue
has been completely wiped up, and the area surrounding the
engine is dry.
2.
Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward - SLOW, lever back toward operator FAST).
3.
Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
4.
Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
WARNING
Operating the engine without an air
filter, with a damaged air filter, or a filter
in need of replacement will allow dirt
to enter the engine, causing rapid
engine wear.
Burn Hazard
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the
muffler removed.
8.
Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
9.
Muffler – Used to reduce noise and emissions.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
PAGE 14 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW PLATE COMPACTOR — INSPECTION
Before Starting
1.
Read safety instructions at the
beginning of manual.
2.
Clean the compactor, removing
dirt and dust, particularly the
engine cooling air inlet, carburetor
and air cleaner.
3.
Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
4.
Check carburetor for external dirt and dust. Clean with dry
compressed air.
5.
Check fastening nuts and bolts for tightness. Loosened
screws or bolts due to vibration, could lead to unexpected
accident.
The Oil Alert System will automatically
stop the engine before the engine falls
below safe limits. Always be sure to
check the engine oil level prior to
starting the engine.
NOTE
Table 3. Oil Type
Season
Temperature
Oil Type
Summer
25°C or Higher
SAE 10W-30
Spring/Fall
25°C~10°C
SAE 10W-30/20
Winter
0°C or Lower
SAE 10W-10
Engine Oil Check
1.
To check the engine oil level, place the pump on secure
level ground with the engine stopped.
2.
Remove the filler dipstick from the engine oil filler hole
(Figure 3) and wipe clean.
DANGER
Explosive
Fuel Hazard
Adding fuel to the fuel tank should be done only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel
spill, DO NOT attempt to start the engine until the
fuel residue has been completely wiped up, and the area
surrounding the engine is dry. DO NOT attempt to refuel the
compactor if the engine is hot! or running.
Fuel Check
Figure 3. Engine Oil Dipstick (Removal)
3. Insert and remove the dipstick without screwing it into the filler
neck. Check the oil level shown on the dipstick.
4. If the oil level is low (Figure 4), fill to the edge of the oil filler
hole with the recommended oil type (Table 3). Maximum oil
capacity is 0.63 quarts (0.60 liters)
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if the fuel level is low. If fuel is low,
replenish with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel immediately!
Figure 4. Engine Oil Dipstick (Oil Level)
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 15
MVC-88VGH/VGHW— INSPECTION
2. The V-belt tension is proper if the V-belt bends 10 to 15 mm
(Figure 7) when depressed with finger at midway between
the clutch and vibration pulley shafts.
V-Belt Check
CAUTI
CAUTION
NEVER attempt to check the V-belt with the engine running.
Severe injury can occur of your hand (Figure 5) gets caught
between the V-belt and the clutch. Always use safety gloves.
CLUTCH
PULLEY
Figure 7. V-Belt Tension
VIBRATOR
PULLEY
3. A loose V-belt will decrease the power transmission output,
causing reduced compaction and premature wear of the
belt.
4. If the V-belt becomes worn or loose, replace it.
Figure 5. V-Belt Hazard
1. To check the V-belt tension, remove the three bolts that
secure the belt cover to the frame as shown in Figure 6.
Vibrator Oil Check
1. Place the MVC-88VGH/VGHW plate compactor horizontally
on a flat surface. Make sure the compactor is level when
checking the oil in the vibrator assembly.
2. Check vibrator oil level by removing the plug (vibrator oil gauge)
as shown in Figure 8. The oil level should be up to the oil plug.
The vibrator holds 140 cc (approximately 4 ounces).
IMPORTANT, if oil is required, replace using only SAE10W-30
motor oil.
l
Figure 8. Vibrator Oil Plug
Figure 6. V-Belt Cover Removal
PAGE 16 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW— INITIAL START-UP
CAUTI
CAUTION
The CLOSED position of the
choke lever enriches the fuel
mixture for starting a COLD
engine. The OPEN position
provides the correct fuel
mixture for normal operation
after starting, and for restarting
a warm engine.
NOTE
D
DO NOT attempt to run the compactor until
the Safety and Initial Start-upsectionshave
been read and understood.
1. Place the fuel valve lever (Figure 9) in the "ON" position.
4. Place the throttle lever (Figure 12) halfway between fast
and slow.
Figure 9. Fuel Valve Lever
2. Place the Engine ON/OFF switch (Figure 10) in the "ON"
position.
Figure 12. Throttle Lever
5. Grasp the starter grip (Figure 13) and slowly pull it out. The
resistance becomes the hardest at a certain position, corresponding the compression point. Rewind the rope a little from
that point and pull out sharply.
CAUTI
CAUTION
Figure 10. Engine ON/Off Switch
DO NOT pull the starter rope all the way to the end
3. Place the Choke Lever (Figure 11) in the "OPEN" position.
D
DO NOT release the starter rope after pulling. Allow it to
rewind as soon as possible.
Nnnn
Figure 11. Choke Lever
Figure 13. Starter Grip
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 17
MVC-88VGH/VGHW— INITIAL START-UP/OPERATION
6. If the engine has started, slowly return the choke lever
(Figure 11) to the CLOSED position. If the engine has not
started repeat steps 1 through 5.
7. Before the compactor is put into operation run the engine for
3-5 minutes.
8. Check for abnormal engine noises or fuel leaks.
Stopping the Engine
CAUTI
CAUTION
D
NEVER stop the engine suddenly while working at high
speeds.
Operation
1. Place the throttle lever (Figure 12) in slow position, and
listen for the engine speed to decrease.
CAUTI
CAUTION
Make sure to follow all safety rules referenced in the safety
section of this manual before operating compactor. Keep work
area clear of debris and other objects that could cause
damage to the compactor or bodily injury.
2. Place the Engine ON/OFF switch (Figure 10) in the "OFF
" position.
3. Place the fuel valve lever (Figure 9) in the "OFF" position.
1. Once the engine has started, move the engine throttle lever
quickly to the fast position.
2. With the throttle lever in the fast position, the engine speed
should be around 2,300 RPM, therefore engaging the centrifugal clutch.
NOTE
ALWAYS move the throttle lever
quickly without hesitation,
because increasing the engine
speed slowly causes the clutch
to slip.
5. Firmly gasp the compactor's handle bar with both hands , the
compactor will begin moving forward.
6. Slowly walk behind the compactor and be on the lookout for
any large objects or foreign matter that might cause damage
to the compactor or bodily injury.
l
7. Compactor traveling speed may drop on soils which contain
clay, however there may be cases where traveling speed
drops because the compaction plate does not leave the
ground surface easily due to the composition of the soil. To
rectify this problem do the following:
■ Check the bottom plate to see if clay or equivalent material
has been lodge in the plate mechanism. If so, wash with
water and remove.
■ Remember the compactor does not work as efficiently on
clay or soils that have a high moisture content level.
■ If the soil has a high moisture level, dry soil to appropriate
moisture content level or carry out compaction twice.
PAGE 18 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW— MAINTENANCE
CAUTI
CAUTION
CAUTI
CAUTION
These inspection intervals are for operation under normal
conditions. Adjust your inspection intervals based on the
number hours plate compactor is in use, and particular
working conditions.
Inspection and other services should always be carried out
on hard and level ground with the engine shutdown.
Inspection and Maintenance Service Tables.
1. To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance with Tables 4 through 6.
CAUTI
CAUTION
Fuel piping and connections should be replaced every 2
years.
Table 4. Engine Maintenance Schedule
DESCRIPTION (3)
OPERATION
BEFORE
CHECK
X
FIRST
EVERY
MONTH 3 MONTHS
OR
OR
10 HRS.
25 HRS.
EVERY
6 MONTHS
OR
50 HRS.
EVERY
Y E AR
OR
100 HRS.
EVERY
2 YEARS
OR
200 HRS.
Engine Oil
CHANGE
CHECK
X
X
Air Cleaner
CHANGE
All Nuts & Bolts
Re-tighten If
Necessary
X (1)
X
CHECK-CLEAN
X
Spark Plug
REPLACE
X
Cooling Fins
CHECK
X
Spark Arrester
CLEAN
X
Fuel Tank
CLEAN
X
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
X (2)
Valve Clearance
CHECK-ADJUST
Fuel lines
CHECK
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA Shop Manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 19
MVC-88VGH/VGHW — MAINTENANCE
ENGINE OIL
TABLE 5. MACHINE INSPECTION
Item
Hours of Operation
Remarks
(Star ting check)
Every 8 hours (every
day)
Loosened or lost
screws
Every 8 hours (every
day)
Damage of any par t
Every 8 hours (every
day)
Function of controlling
system par t
Every 8 hours (every
day)
Vibrator oil check
Every 100 hours
See page 19.
Vibrator oil
replacement
Every 200 hours
See page 19.
V-belt (clutch) check
Every 200 hour
See page 19.
1. Drain the engine oil when the oil is warm as shown in
Figure 14.
2. Remove the dipstick and then unscrew the oil plug and
allow the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 3. For engine oil capacity, see Table 2 (engine
specifications). DO NOT overfill.
4. Install drain bolt with sealing washer and tighten securely.
Daily Service
■ Check for leakage of fuel or oil.
■ Check engine oil.
■ Check for loose screws including tightness. See Table 6
below (tightening torque ), for retightening.
ENGINE AIR CLEANER
TABLE 6.
TIGHTENING TORQUE (in. kg/cm) Diameter
Material 6mm
8mm
10mm 12mm 14mm 16mm 18mm 20mm
4T
70
150
300
500
750
1,100
1,400
2 ,0 0 0
6-8T
100
250
500
800
1,300
2,000
2,700
3 ,8 0 0
11T
150
400
800
1,200
2,000
2,900
4,200
5 ,6 0 0
*
Figure 14. Engine Oil (Draining)
100 (6mm) 300 ~ 350 (8mm)l 650 ~ 700 (10mm)
* (In case counter-par t is of aluminum)
(Threads in use with this machine are all right handed)
Material and quality of material is marked on each bolt,
and screw.
1. Remove the air cleaner cover and foam filter element as
shown in Figure 15.
2. Tap the paper filter element (Figure 15) several times on a
hard surface to remove dirt, or blow compressed air [not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter
element from the air cleaner case side. NEVER brush off dirt.
Brushing will force dirt into the fibers. Replace the paper filter
element if it is excessively dirty.
3. Clean foam element in warm, soapy water or nonflammable
solvent. Rinse and dry thoroughly. Dip the element in clean
engine oil and completely squeeze out the excess oil from the
element before installing.
PAGE 20 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW— MAINTENANCE
Checking and Replacing the V-Belt and Clutch
1. After 200 hours of operation, remove the upper belt cover to
check the V-belt tension. Tension is proper if the belt bends
about 10 mm when depressed strongly with finger between
shafts. Loose or worn V-belts reduces power transmission
efficiency, causing weak compaction and reduces the life of
the belt itself.
CAUTI
CAUTION
Whenever the compactor's vibration becomes weak or lost
during normal operation regardless of operation hours, check
the V-belt and clutch immediately.
■ Replacing the V-belt
Remove the upper and lower belt covers. Engage an offset
wrench (13 mm) or the like to vibrator pulley (lower) fastening
bolt. Engage waste cloth or the like at midway of V-belt on the left
side and while pulling it back strongly, rotate the offset wrench
clockwise so that the V-belt will come off.
Figure 15. Air Cleaner
CHANGING VIBRATOR OIL
1. When changing the vibrator oil, remove the drain plug
located at the bottom- right of the vibrator (Figure 5), and
simply tip the compactor to drain the oil. Note that the oil will
drain more easily while it is hot. Remember to use only
10W-30 motor oil when replacing vibrator oil.
CAUTI
CAUTION
■ Reinstalling the V-belt
Engage V-belt to lower vibrator pulley and push the V-belt to left
side of upper clutch and, in the same manner as in removal,
rotate offset wrench clockwise so that the V-belt goes back on.
■ Checking Clutch
Check the clutch simultaneously with V-belt checking. With belt
removed, check outer drum of the clutch for seizure and "V"
groove for wear or damage with your eyes. Clean the "V" groove
as necessary. Wear of lining or shoe should be checked with
running check. If the shoe is worn, power transmission becomes
deficient and slipping will result.
NEVER attempt to check the V-belt with the engine running.
Severe injury can occur if your hand (Figure 6) gets caught
between the V-belt and the clutch. Always use safety gloves.
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 21
MVC-88VGH/VGHW— PREPARATION FOR LONG -TERM STORAGE
Plate Compactor Storage
For storage of the plate compactor for over 30 days, the
following is required:
■ Drain the fuel tank completelyor add STA-BIL to the fuel.
■ Run the engine until the fuel is completely consumed.
■ Completely drain the oil from the engine crankcase and
follow procedures described in the HONDA engine Owner's
Manual for engine storage.
■ Completely drain the compactor's hydraulic oil from the
vibrating case.
■ Clean entire plate compactor, especially the bottom plate
removing all dirt and foreign matter.
■ Cover plate compactor and engine with plastic covering
or equivalent and store in a clean, dry place.
l
PAGE 22 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW—TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
diagnosis based on the Engine , and Compactor
Troubleshooting (Tables 7, and 8) information shown below
and on the proceeding pages.
If the problem cannot be remedied, please leave the unit
just as it is and consult or company's service department.
TABLE 7. ENGINE TROUBLESHOOTING
SYMPTOM
Difficult to star t, "fuel is available, but no
SPARK at spark plug".
POSSIBLE CAUSE
Spark plug bridging?
Check gap, insulation or
replace spark plug.
Carbon deposit on spark plug?
Clean or replace spark plug.
Shor t circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
Set to proper gap.
ON/OFF switch is shor ted?
Check switch wiring, replace
switch.
Ignition coil defective?
Replace ignition coil.
Difficult to star t, "fuel is available, and Improper spark gap, points dir try?
SPARK is present at the spark plug".
Difficult to star t, "fuel is available, spark
is present and compression is normal"
Difficult to star t, "fuel is available, spark
is present and compression is low"
No fuel present at carburetor.
SOLUTION
Set correct spark gap and
clean points.
Condenser insulation worn or shor t
circuiting?
Replace condenser.
Spark plug wire broken or shor t circuiting?
R e p l a c e d e fe c t i ve s p a r k p l u g
wiring.
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Water or dust in fuel system?
Flush fuel system.
Air cleaner dir ty?
Clean or replace air cleaner.
Suction/exhaust valve stuck or protruded?
Re-seat valves.
Piston ring and/or cylinder worn?
Replace piston rings and or
piston.
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
sp a r k p lu g .
Head gasket and/or spark plug gasket
damaged?
Replace head and spar k plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Fuel cock does not open properly?
Apply lubr icant to loosen fuel
cock lever, replace if necessary.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Clean or replace fuel tank cap.
Air in fuel line?
Bleed fuel line.
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 23
MVC-88VGH/VGHW—TROUBLESHOOTING (ENGINE COMPACTOR)
TABLE 7. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
"Weak in power" compression is
proper and does not misfire.
POSSIBLE CAUSE
SOLUTION
Air cleaner not clean?
Clean or replace air cleaner
Improper level in carburetor?
Check float adjustment, re-build
carbureator.
Defective Spark plug?
Clean or replace spark plug.
Defective Spark plug?
"Weak in power" compression is
proper but misfires.
Engine overheats.
Rotational speed fluctuates.
Recoil star ter malfunction.
l
Water in fuel system?
Flush fuel system, and replace
with correct type of fuel.
Dir ty spark plug?
Clean or replace spark plug.
Ignition coil defective?
Replace ignition coil.
Spark plug heat value improper?
Replace with correct type of
spark plug.
Correct type of fuel?
Replace with correct type of fuel
Cooling fins dir ty?
Clean cooling fins.
Governor adjusted correctly?
Adjust governor.
Governor spring defective?
Replace governor spring.
Fuel flow restricted?
C h e c k e n t i r e f u e l s y s t e m fo r
leaks or clogs.
Recoil mechanism clogged with dust and
dir t?
Clean recoil assembly with soap
and water.
Sprial spring loose?
Replace sprial spring.
TABLE 8. PLATE COMPACTOR TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Engine speed too low?
Set engine speed to correct RPM.
Clutch slips?
Check or replace clutch.
V-belt slips?
Adjust or replace V-belt.
Travel speed too low, and vibration is Excessive oil in vibrator?
weak.
Drain excess oil and fill to proper level.
Malfunction in vibrator housing?
Check eccentric, gears and counter
weights.
Bearing Failure?
Replace Bearing
Insufficient engine output?
Check engine, compression etc.
PAGE 24 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
NOTES
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 25
MVC-88VGH/VGHW— EXPLANATION OF CODES IN REMARKS COLUMN
The following section explains the different symbols and
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice. Multiquip
does not guarantee the availability of the parts listed.
SAMPLE PARTS LIST
NO.
1
2%
2%
3
4
PART NO. PART NAME
QTY. REMARKS
12345
BOLT......................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN............NOT SOLD SEPARATELY
12347
WASHER, 3/8 IN....1 .....MQ-45T ONLY
12348
HOSE ..................A/R ...MAKE LOCALLY
12349
BEARING ..............1 .....S/N 2345B AND ABOVE
NO. Column
QTY. Column
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
REMARKS Column
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
Unique Symbols — All items with same unique
symbol
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Duplicate Item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
NOTICE
When ordering a part that has more than one item
l column for help in
number listed, check the remarks
determining the proper part to order.
PART NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items. Examples include battery cables, shims,
and certain washers and nuts.
“Not Sold Separately” — Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
PAGE 26 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW — SUGGESTED SPARE PARTS
MVC-88GH/GW 1 TO 5 UNITS WITH HONDA
GX160U1QMX2 ENGINE
1 to 5 Units
Qty.
P/N
Description
3 ......... 070100332 ............. V-BELT
5 ......... 0650140480 ........... SPARK PLUG
1 ......... 28462ZH8003 ........ ROPE, RECOIL STARTER
5 ......... 17210ZE1517 ........ ELEMENT, AIR CLEANER
1 ......... 17620Z0T305 ........ CAP, FUEL TANK
1 ......... 17672ZE2W01 ....... FUEL FILTER, FUEL TANK
4 ......... 939010140 ............. SHOCK ABSORBER
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 27
MVC-88VGH/VGHW— NAME PLATE AND DECALS
NAME PLATE AND DECALS
9
10
11
2
3
1
4
5
6
8
7
l
6
PAGE 28 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW— NAME PLATE AND DECALS
NAME PLATE AND DECALS
NO
PART NO
PART NAME
QTY. REMARKS
1
920206290
DECAL, READ OWNERS MANUAL .......1 ........ NPA-629
2
920203290
DECAL, CAUTION ................................. 1 ........ NPA-329
3
920208450
DECAL, LIFTING ...................................1 ........ NPA-845
4
920203060
DECAL, CAUTION (START ENG/VIBR) .1 ........ NPA-306
5
920208350
DECAL, V- BELT RPF-3330 ...................1 ........ NPA-835
6
920201580
DECAL, MQ LOGO ................................2 ........ NPA-158
7
920105070
DECAL, MIKASA LOGO (NAME) .......... 1 ........ NPA-507
8
920201950
DECAL, MOTOR OIL ..............................1 ........ NPA-195
9
920101410
DECAL, MIKASA LOGO (TRIANGLE) ... 1 ........ NPA-141
10
NAMEPLATE, SERIAL NO. ...................1 ........ CONTACT MQ PARTS DEPT. W/MODEL & S/N
11
920203330
EAR PROTECTION LABEL ...................1 ........ NPA-333
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 29
MVC-88VGH/VGHW— BODY ASSY.
BODY ASSY.
106
104
105
108
101
104
105
107
102
96
102
103
103
9795
93
91
92
94
92
35
36
37
93
95
9796
46
38
32
41
33
31
42
12
52
57
32 54
55
56
l
51
47
45
4849
54
55
56
33
39
25
23
40
43
54
55
56
24
53
24
25
23
21
PAGE 30 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW— BODY ASSY.
BODY
NO
12
21
23
24
25
31
32
33
35
36
37
38
39
40
41
42
43
45
46
47
48
49
51
52
53
54
55
56
57
91
92
93
94
95
96
97
101
102
103
104#
105#
106#
107#
108#
ASSY.
PART NO
416454360
416115973
939010140
020310080
030210250
416115980
001221025
030210250
912216011
001220845
030208200
031108160
404412290
416452780
031108160
022710809
959404350
416338990
2062600113
416452800
952400130
009110004
070100332
416115950
416010020
001220825
030208200
031108160
001220820
416910070
416452730
404433430
416452360
952405600
001211253
030212300
416115940
001221025
030210250
416459340
009120407
416217070
416118520
416459320
PART NAME
QTY.
REMARKS
RUBBER PLATE 25X25X8
1
VIBRATING PLATE
1
SHOCK ABSORBER 50D-45H
4
NUT M10
4
WASHER SW M10
4
BASE
1
BOLT 10X25 T
4
WASHER, LOCK M10
4
ENGINE ASSY. GX160U1QMX2
1
BOLT 8X45 T
4
WASHER, LOCK M8
4
WASHER, FLAT M8
4
ENGINE NUT
1
ENGINE NUT (W/BOLT)
1
WASHER, FLAT M8
1
NYLON NUT M8
1
EARTH WIRE
1
CLUTCH ASSY.
1
KEY 4.77 X 4.77 X 35
1
COLLAR 19.05-25-15.6
1
WASHER
1
SOCKET HEAD BOLT 5/16X24
1
V-BELT RPF-3330
1
BELT COVER (INSIDE)
1
BELT COVER
1
BOLT 8X25 T
4
WASHER, LOCK M8
5
WASHER, FLAT M8
1
BOLT 8X20 T
1
VIB. PROOF HANDLE ASSY ................ 1 ........... INCLUDES ITEMS W/ #
COLLAR 13-20-44
2
RUBBER 20X32X28.5/52H
2
HANDLE STOPPER
2
WASHER 12.5 X 35 X 4.5
2
BOLT 12X65 H
2
WASHER, LOCK M12
2
GUARD HOOK
1
BOLT 10X25 T
4
WASHER, LOCK M10
4
RUBBER
2
BOLT, SUNK HEAD 10X20T
2
GRIP, HANDLE
1
VIB. PROOF HANDLE
1
NUT, VIB. PROOF HANDLE
2
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 31
MVC-88VGH/VGHW— VIBRATOR ASSY.
VIBRATOR ASSY.
l
PAGE 32 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW— VIBRATOR ASSY.
VIBRATOR ASSY.
NO
PART NO
A
416910030
61#
416115991
62#
953400270
63#
953405260
64
001221640
65
030216400
66
031116260
68#
416215530
69#
040306211
70#
416338900
71#
416338910
72#
416338920
73#
060403060
74#
050101000
75#
001220825
76#
030208200
78#
416454430
79#
951405240
80#
952404250
81#
001221025
82#
030210250
PART NAME
QTY.
REMARKS
VIBRATOR ASSY .................................. 1 ........... INCLUDES ITEMS W/ #
VIBRATING CASE
1
PLUG 1/4X14 10L
1
PACKING 1/4
1
BOLT 16X40 T
4
WASHER, LOCK M16
4
WASHER, FLAT M16
4
ECCENTRIC ROTATOR
1
BEARING 6211C3
2
CASE COVER (R)
1
CASE COVER (L)
1
BELT COVER GUARD
1
OIL SEAL TC-35488
1
O-RING G-100
2
BOLT 8X25 T
8
WASHER, LOCK M8
8
PULLEY A1-28-81-20
1
KEY 7X7X19 R
1
WASHER 11X40X4
1
BOLT 10X25 T
1
WASHER, LOCK M10
1
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 33
MVC-88VGH/VGHW— SPRINKLER ASSY. (OPTION)
SPRINKLER ASSY. (OPTION)
122
123
121
123
124
113
111
112
114
l
l
119
116
118
120
115
117
118
PAGE 34 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW— SPRINKLER ASSY. (OPTION)
SPRINKLER ASSY. (OPTION)
NO
111
112
113
114
115
116
117
118
119
120
121#
122#
123#
124#
PART NO
416910010
033910050
953406390
954403241
416338930
416338940
416452750
001220825
416453780
416452790
954300342
001241030
033910010
022910180
PART NAME
QTY.
REMARKS
WATER TANK (W/CAP ONLY) ...... 1 ............... REPLACES 416116010 INCLUDES ITEMS W/#
WASHER 14.5X30X1.6
1
PACKING 13X28X2
1
COCK PT1/4
1
SPRINKLING PIPE
1
PIPE HOLDER (L)
1
PIPE HOLDER (R)
1
FLANGE BOLT 8X25
2
PACKING 8X19X2T
3
STAY, PIPE HOLDER
1
CAP, WATER TANK (NBR)
1
BOLT 10X30
1
WASHER 10.5X21X2
2
NYLON NUT M10
1
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 35
MVC-88VGH/VGHW— TRANSPORT WHEEL ASSY. (OPTION)
TRANSPORT WHEEL ASSY. (OPTION )
l
PAGE 36 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
MVC-88VGH/VGHW— TRANSPORT WHEEL ASSY. (OPTION)
TRANSPORT WHEEL ASSY. (OPTION )
NO
1
2
3
4
5
6
PART NO
416116160
959404310
031120320
025203030
416454150
025403025
PART NAME
WHEEL SHAFT
WHEEL 150X42
WASHER, FLAT M20
SPLIT COTTER PIN 3X30
ROLLER
SPRING PIN 3X25
QTY.
1
2
2
2
2
3
REMARKS
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 37
HONDA GX160U1QMX2 ENGINE — CYLINDER HEAD ASSY.
5
11
15
9
6
11
14
7
14
14
12
4
2
12
1
14
8
3
9
10
10
9
l
PAGE 38 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
1
2
3
4#
5
6
7
8
9
10
11
12
14
15
PART NO.
12204ZE1306
12205ZE1315
12210ZH8405
12216ZE5300
12251ZF1800
12310ZE1020
12391ZE1000
15721ZH8000
90013883000
90043ZE1020
90047ZE1000
9430110160
957230806000
0650140480
PART NAME
QTY.
REMARKS
GUIDE, VALVE (OS)
1
GUIDE, EX. VALVE (OS) ...................................1................INCLUDES ITEMS W/#
HEAD, CYLINDER
1
CLIP, VALVE GUIDE
1
GASKET, CYLINDER HEAD
1
COVER, HEAD
1
GASKET, CYLINDER HEAD COVER
1
TUBE, BREATHER
1
BOLT, FLANGE (6 X 12)
4
BOLT, STUD ( 6 X 112)
2
BOLT, STUD (8 X 32)
2
PIN A, DOWELL (10 X 16)
2
BOLT, FLANGE (8 X 60)
4
SPARK PLUG EY45V
1
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 39
HONDA GX160U1QMX2 ENGINE — CYLINDER BARREL ASSY.
15
3
7
17
10
12
19
19
2
16
17
18
1
13
8
11
11
9
13
9
14
l
PAGE 40 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
1
2
3
7
8
9
10
11
12
13$
14$
15
16
17
18
19
PART NO.
12000ZH8426
15510ZE1033
16510ZE1000
16531ZE1000
16541ZE1000
90131ZE1000
90451ZE1000
90601ZE1000
90602ZE1000
91001ZF1003
91201Z0T801
91353671004
9405010000
9410106800
9425108000
957010601200
PART NAME
QTY.
REMARKS
CYLINDER BARREL ASSY. ..............................1................INCLUDES ITEMS W/ $
SWITCH ASSY., OIL LEVEL
1
GOVERNOR ASSY.
1
SLIDER, GOVERNOR
1
SHAFT, GOVERNOR ARM
1
BOLT, DRAIN PLUG
2
WASHER, THRUST (6MM)
1
WASHER, DRAIN PLUG (10.2MM)
2
CLIP, GOVERNOR HOLDER
1
BEARING, RADIAL BALL (6205)
1
OIL SEAL (25 X 41 X 6)
1
O-RING (14 MM)
1
NUT, FLANGE (10MM)
1
WASHER, PLAIN (6MM)
2
PIN, LOCK (8MM)
1
BOLT, FLANGE (6 X 12)
2
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 41
HONDA GX160U1QMX2 ENGINE — CRANKCASE COVER ASSY.
13
13
5
13
13
9
13
12
11
9
7
4
12
14
1
l
PAGE 42 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
1
4
5
7
9#
11@
12
13
14@
PART NO.
11300ZE1642
11381ZH8801
15600ZE1003
15600ZG4003
15625ZE1003
91201Z0T801
9430108140
957010803200
961006205000
PART NAME
QTY.
REMARKS
COVER ASSY., CRANKCASE ...........................1................INCLUDES ITEMS W/ @
GASKET, CASE COVER
1
OIL GAUGE .......................................................1................INCLUDES ITEMS W/ #
CAP ASSY., OIL FILLER....................................1................INCLUDES ITEMS W/ #
GASKET, OIL FILLER CAP
2
OIL SEAL (25 X 41 X 6)
1
PIN A, DOWEL (8 X 14)
2
BOLT, FLANGE (8 X 32)
6
BEARING, RADIAL BALL (6205)
1
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 43
HONDA GX160U1QMX2 ENGINE — CRANKSHAFT ASSY.
l
PAGE 44 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
4
13
14
15
PART NO.
13310ZE1601
90003ZE1000
90473842000
90745ZE1600
PART NAME
CRANKSHAFT
BOLT, HEX 5/16”
WASHER, 8 MM
KEY, 78 X 38 MM
QTY.
1
1
1
1
REMARKS
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 45
HONDA GX160U1QMX2 ENGINE — PISTON/RINGS ASSY.
l
PAGE 46 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — PISTON/RINGS ASSY.
PISTON/RINGS ASSY.
NO.
1
1
1
1
2
2
2
2
3
4
5@
6
PART NO.
13010ZL0003
13011ZL0003
13012ZL0003
13013ZL0003
13101ZH8010
13102ZH8010
13103ZH8010
13104ZH8010
13111ZE1000
13200ZE1010
90001ZE1000
90551ZE1000
PART NAME
QTY.
REMARKS
RING SET, PISTON (STD)
1
RING SET, PISTON (OS 0.25)
1
RING SET, PISTON (OS 0.50)
1
RING SET, PISTON (0.75)
1
PISTON (STD)
1
PISTON (OS 0.25)
1
PISTON (OS 0.50)
1
PISTON (0.75)
1
PIN, PISTON
1
ROD ASSY., CONNECTING ..............................1................INCLUDES ITEMS W/@
BOLT, CONNECTING ROD
2
CLIP, PISTON PIN (18MM)
2
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 47
HONDA GX160U1QMX2 ENGINE — CAMSHAFT ASSY.
15
6
18
8
6
14
12
13
12
2
11
9
1
10
7
4
17
4
7
17
18
16
8
l
PAGE 48 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
1
2
4
6
7
8
9@
10
11
12
13
14
15
16
17
18
PART NO.
12209ZH8003
14100ZE1812
14410ZE1010
14431ZE1000
14441ZE1010
14451ZE1013
14568ZE1000
14711ZF1000
14721ZF1000
14751ZF1000
14771ZE1000
14773ZE1000
14781ZE1000
14791ZE1010
90012ZE0010
90206ZE1000
PART NAME
QTY.
REMARKS
SEAL, VALVE STEM
1
CAMSHAFT ASSY. ............................................1................INCLUDES ITEMS W/@
ROD, PUSH
2
ARM, VALVE ROCKER
2
LIFTER, VALVE
2
PIVOT, ROCKER ARM
2
SPRING, WEIGHT RETURN
1
VALVE, INLET
1
VALVE, EXHAUST
1
SPRING VALVE
2
RETAINER, IN. VALVE SPRING
1
RETAINER, EX. VALVE SPRING
1
ROTATOR, VALVE
1
PLATE, PUSH ROD GUIDE
1
BOLT, PIVOT (8MM)
2
NUT, PIVOT ADJ.
2
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 49
HONDA GX160U1QMX2 ENGINE — RECOIL STARTER ASSY.
12
7
5
8
14
6
4
10
11
5
1
13
9
2
15
l
PAGE 50 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
1
2@
4@
5@
6@
7@
8@
9@
10@
11@
12@
13
14@
15
PART NO.
28400ZH8023ZB
28410ZH8003ZB
28421ZH8801
28422ZH8801
28431ZH8801
28431ZH8801
28441ZH8801
28442ZH8003
28443ZH8001
28461ZH8003
28462ZH8003
32901MA1000
90003ZH8001
90008ZE2003
PART NAME
QTY.
REMARKS
STARTER ASSY., RECOIL ...............................1................INCLUDES ITEMS W/@
CASE, RECOIL STARTER
1
REEL, RECOIL STARTER
1
RATCHET, STARTER
2
PLATE, FRICTION
1
GUIDE, RATCHET
1
SPRING, FRICTION
1
SPRING, RECOIL STARTER
1
SPRING, RETURN
2
KNOB, RECOIL STARTER
1
ROPE, RECOIL STARTER
1
CLIP, CORD
1
SCREW, SETTING
1
BOLT, FLANGE (6 X 10)
1
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 51
HONDA GX160U1QMX2 ENGINE — FAN COVER ASSY.
22
6
14
25
2
16
21
17
10
20
20
20
l
PAGE 52 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO.
2
6
10
14
16
17
20
21
22
25
26
PART NO.
19610ZE1000ZC
19611ZH8810
19630ZH8000
34150ZH7003
3610ZE1010
36100ZF6P81
90013883000
90022888010
90601ZH7013
957010600800
87532ZH7000
PART NAME
COVER, FAN *NH1* (BLACK)
PLATE, SIDE (OIL ALERT)
SHROUD
ALERT UNIT, OIL
CORD, STOP SWITCH (370MM)
SWITCH ASSY., ENGINE STOP
BOLT, FLANGE (6 X 12) (CT200)
BOLT, FLANGE (6 X 20) (CT200)
CLIP, HARNESS
BOLT, FLANGE (6 X 8)
MARK, THROTTLE INDICATION
QTY.
1
1
1
1
1
1
6
1
1
1
1
REMARKS
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 53
HONDA GX160U1QMX2 ENGINE — CARBURETOR ASSY.
15
38
14
31
26
2
27
25
17
20
28
11
6
13
29
12
37
3
34
9
16
4
10
2
5
8
2
2
7
l
PAGE 54 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
2@
3@
4@
5@
6@
7@
8@
9@
10
11@
12@
13@
14
15
16
17
20
25@
26@
27@
28@
29@
31@
34#
37@
38@
PART NO.
16010ZE1812
16011ZE0005
16013ZE0005
16015ZE0831
16016ZH7W01
16024ZE1811
16028ZE0005
16044ZE0005
16100ZH8W51
16124ZE0005
16166ZH8W50
16173001004
16211ZE1000
16212ZH8800
16220ZE1020
16221ZH8801
16610ZE1000
16953ZE1812
16954ZE1812
16956ZE1811
16957ZE1812
16967ZE0811
93500030060H
9430520122
99101ZH80700
99204ZE00350
PART NAME
QTY.
REMARKS
GASKET SET
1
VALVE SET, FLOAT
1
FLOAT SET
1
CHAMBER SET, FLOAT ....................................1................INCLUDES O-RING
SCREW SET
1
SCREW SET, DRAIN .........................................1................INCLUDES GASKET
SCREW SET B ..................................................1................INCLUDES GASKET
CHOKE SET
1
CARBURETOR ASSY. (BE65B B) .....................1................INCLUDES ITEMS W/ @
SCREW, THROTTLE STOP
1
NOZZLE, MAIN
1
O-RING
1
INSULATOR, CARBURETOR
1
GASKET, INSULATOR
1
SPACER, CARBURETOR
1
GASKET, CARBURETOR
1
LEVER, CHOKE (STD) ......................................1................INCLUDES ITEMS W/ #
LEVER, VALVE
1
PLATE, LEVER SETTING
1
SPRING, VALVE LEVER
1
GASKET, VALVE
1
CUP, FUEL STRAINER
1
SCREW, PAN (3 X 6)
2
PIN, SPRING (2 X 12)
1
JET, MAIN (#70)
1
JET, SET, PILOT (#35) .......................................1................INCLUDES GASKET
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 55
HONDA GX160U1QMX2 ENGINE — AIR CLEANER ASSY.
10
1
4
12
2
10
5
8
3
6
9
7
13
11
7
11
l
PAGE 56 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
1
2
3@
4
5@
6
7#
8#
9
10
11
12
13#
PART NO.
16271ZE1000
17210ZE1517
17218ZE1507
17230ZE1820
17232891000
17235ZE1831
17238ZE7010
17239ZE1000
17410ZE1020
90325044000
9405006000
957010602000
57528ZH7000
PART NAME
QTY.
REMARKS
GASKET, ELBOW
1
ELEMENT, AIR CLEANER ...............................1................INCLUDES ITEMS W/@
FILTER (OUTER)
1
COVER, AIR CLEANER
1
GROMMET, AIR CLEANER
1
NOISE, MUFFLER
1
COLLAR, AIR CLEANER
2
COLLAR B, AIR CLEANER
1
ELBOW, AIR CLEANER ....................................1................INCLUDES ITEMS W/ #
WINGNUT, TOOL BOX SETTING
1
NUT, CAP (6 MM)
2
BOLT, FLANGE (6 X 20)
1
MARK, CHOKE
1
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 57
HONDA GX160U1QMX2 ENGINE — MUFFLER ASSY.
19
19
22
2
4
15
16
7
6
19
16
5
19
23
27
23
9
17
23
l
PAGE 58 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO.
2
4
5
6
7
9
15
16
17
19
22
23
27
PART NO.
18310ZK8V50
18320ZF1H01
18325ZE1010
18340ZE1010
18355ZE1000
18381ZH8800
18522ZE1000
90002ZG0003
90016ZE1000
90050ZE1000
90055ZE1000
90055ZE1000
94001080000S
PART NAME
MUFFLER
PROTECTOR, MUFFLER
PROTECTOR, LOWER
DEFLECTOR CP
ARRESTER, SPARK
GASKET, MUFFLER
GUIDE, MUFFLER
SCREW, TAPPING (4 X 8)
FLANGE BOLT 6 X13
SCREW, TAPPING (5 X 8)
SCREW, TAPPING (4 X 6)
SCREW, TAPPING (4 X 6)
NUT, HEX (8MM)
QTY.
1
1
1
1
1
1
1
2
1
4
1
4
2
REMARKS
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 59
HONDA GX160U1QMX2 ENGINE — FUEL TANK ASSY.
29
12
13
14
11
18
20
17
28
27
28
24
7
21
3
l
PAGE 60 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — FUEL TANK ASSY.
FUEL TANK ASSY.
NO.
3
7
11
12
13@
14
17
18
20
21
24
27
27
28
29
PART NO.
16854ZH8000
16955ZE1000
17510ZE1020ZF
17620Z0T305
17631Z0T812
17672ZE2W01
90004ZH7003
90404680000
91319ME5003
91353671004
9405006000
950014514040
950014500160M
9500202080
87516ZH7000
PART NAME
QTY.
REMARKS
RUBBER, SUPPORTER (107MM)
1
JOINT, FUEL TANK
1
TANK, FUEL *NH1* (BLACK)
1
CAP, FUEL FILLER ............................................1................INCLUDES ITEMS W/@
GASKET, FUEL FILLER CAP
1
FILTER, FUEL
1
BOLT, FLANGE (6 X 29)
1
WASHER, 6.5 X 25 X 1.5
2
O-RING (5.5 X 1.4)
2
O-RING (13 MM)
1
NUT, FLANGE (6MM)
2
FUEL TUBE (4.5 X 140)
1
BULK HOSE, FUEL (4.5 X 1M)
1
CLIP, TUBE
2
MARK, OPERATION CAUTION
1
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 61
HONDA GX160U1QMX2 ENGINE — COOLING FAN & FLYWHEEL ASSY.
6
1
10
2
5
l
PAGE 62 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — COOLING FAN & FLYWHEEL ASSY.
COOLING FAN AND FLYWHEEL ASSY.
NO.
1
2
5
6
10
PART NO.
13331357000
19511ZE1000
28451ZH8001
31100ZE1010
90201878003
PART NAME
KEY, SPECIAL WOODRUFF (25 X 18)
FAN, COOLING
PULLEY, STARTER
FLYWHEEL
NUT, SPECIAL (14MM)
QTY.
1
1
1
1
1
REMARKS
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 63
HONDA GX160U1QMX2 ENGINE — IGNITION COIL ASSY.
l
PAGE 64 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
1
2
7
11
PART NO.
30500ZE1063
30700ZE1013
36101ZE1010
90121952000
PART NAME
COIL ASSY., IGNITION
CAP ASSY.
WIRE, STOP SWITCH (370MM)
BOLT, FLANGE (6 X 25)
QTY.
1
1
1
2
REMARKS
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 65
HONDA GX160U1QMX2 ENGINE — CONTROL ASSY.
5
28
21
7
2
8
23
26
13
12
11
17
25
18
24
10
6
14
20
27
20
15
16
l
PAGE 66 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
HONDA GX160U1QMX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO.
2
5
6
7
8
10@
11@
12@
13@
14@
15@
16@
17@
18@
20
21
23@
24@
25@
26@
27@
28
PART NO.
16500ZH8813
16551ZE0010
16555ZE1000
16561ZE1020
16562ZE1020
16571ZH8020
16574ZE1000
16575ZH8000
16576891000
16578ZE1000
16580ZH8813
16584883300
16592ZE1810
16594883010
90013883000
90015ZE5010
90114SA0000
90605230000
93500040060H
93500050160A
93500050250H
9405006000
PART NAME
QTY.
REMARKS
CONTROL ASSY................................................1................INCLUDES ITEMS W/@
ARM, GOVERNOR
1
ROD, GOVERNOR
1
SPRING, GOVERNOR
1
SPRING, THROTTLE RETURN
1
LEVER CONTROL
1
SPRING LEVER
1
WASHER, CONTROL LEVER
1
HOLDER, CABLE
1
SPACER, CONTROL LEVER
1
BASE CONTROL
1
SPRING, CONTROL ADJUSTING
1
SPRING, CABLE RETURN
1
HOLDER, WIRE
1
BOLT, FLANGE (6 X 12) (CT200)
2
BOLT, GOVERNOR ARM
1
NUT, SELF-LOCK (6MM)
1
CIRCLIP
1
SCREW, PAN (4 X 6))
1
SCREW, PAN (5 X 16)
1
SCREW, PAN (5 X 25)
1
NUT, FLANGE (6MM)
1
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 67
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5.
Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
6.
The following items are not returnable:
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
a.
SPECIAL EXPEDITING SERVICE
Terms of payment for parts are net 30 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
b.
MINIMUM ORDER
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
RETURNED GOODS POLICY
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
1.
2.
A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
c.
Any line item with an extended
dealer net price of less than
$5.00.
d.
Special order items.
e.
Electrical components.
f.
Paint, chemicals, and lubricants.
g.
Decals and paper products.
h.
Items purchased in kits.
7.
The sender will be notified of any material
received that is not acceptable.
To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
8.
Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
a.
The parts numbers and descriptions
must match the current parts price
list.
9.
b.
The list must be typed or computer
generated.
Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
c.
The list must state the reason(s)
for the return.
d.
The list must reference the sales
order(s) or invoice (s) under
which the items were originally
purchased.
e.
l
The list must include the name
and phone number of the person
requesting the RMA.
3.
A copy of the Return Material Authorization
must accompany the return shipment.
4.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
LIMITATIONS OF SELLER’S LIABILITY
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
LIMITATION OF WARRANTIES
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
Effective: February 22, 2006
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
PAGE 68 — MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10)
NOTES
MVC-88VGH/VGHW PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #2 (08/06/10) — PAGE 69
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
MQ Parts Department
Tel. (800) 421-1244
Fax (800) 537-3927
Mayco Parts
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Warranty Department
800-306-2926
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
800-421-1244, Ext. 279
310-537-3700, Ext. 279
Fax: 310-537-1173
Technical Assistance
800-421-1244
310-537-3700
Fax: 310-537-4259
800-478-1244
Fax: 310-631-5032
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: [email protected]
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Unit 2, Northpoint Industrial Estate,
Global Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: [email protected]
Tel: 0161 339 2223
Fax: 0161 339 3226
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2010, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks
are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is: