Slit Lamp HS-7000 Huvitz

Slit Lamp HS-7000 Huvitz
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
Operator’s Manual
SLIT LAMP MICROSCOPE HS-7000
1
2
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
IMPORTANT NOTICE
!
WARNING
P otential electro magnetic or other interference between medical equipments and other
devices being o perated to gether in the same enviro nmental may expert an adverse
influence on functioning o f the medical equipment. Non - medical equipments not in
compliance with the requirements of EN 60601-1 and EN 6 060 1 -1-2 should not be
used together in the same environmental as the medical equipments
This equipment has been tested and found to co mply with the limits for medical devices in
IEC 606 01-1- 2:2001 . These limits are designed to provide reasonable protection against
harmful interference in a typical medical installation
P ower Cord
Fo r use of equipment in rated voltage less than 125Vac, minimum 6A, Type SJT or S VT,
18/3 AW G, 10A, max 3.0m lo ng: One end with Hospital Grade Type, NEM A 5 - 15P other
end with appliance co upler. For use of equipment in rated voltage less than 2 50 Vac ,
minimum 6A, Type SJT or SVT, 18/3AW G, 10A, max 3.0m long: One end terminated with
blade attachment plug (HAR) Type, NEM A 6 - 15 P .
This pro duct may malfunction due to electromagnetic waves caused by portable personal
telephones, transceivers, radio -controlled to ys, etc. Be sure to avoid havi ng objects such as,
which affect this pro duct, brought near the product.
The information in this publication has been carefully checked and is believed to be entirely
accurate at the time of publication. HUVITZ assumes no responsibility, however, for possible
errors o r omissions, or for any consequences resulting from the use o f the
contained herein.
ormatio n
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
HUVITZ reserves the right to make changes in its products or pro duct specificatio ns at any
time and without prior notice, and is not required to update this documentatio n to reflect such
changes.
© 2009 HUVITZ Co ., Ltd.
6 89 -3, Geumjeo ng - dong, Gunpo - si, Gyeonggi -do,
4 35 -862 , Republic of Korea
All rights are reserved.
Under co pyright laws, this manual may not be copied, in whole or in part, witho ut the prior
written consent of HUVITZ Co., Ltd.
Document Number: 9000ENGJ201 -A.
3
4
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
Contents
1.
2.
3.
Introduction ....................................................................................................... 6
1.1.
Indication for use ........................... 오류! 책갈피가 정의되어 있지 않습니다.
1.2.
Classification............................................................................................ 6
Safety Infor mation.............................................................................................. 6
2.1.
Introduction .............................................................................................. 7
2.2.
Safety Symbols ........................................................................................ 8
2.3.
Environment factors................................................................................ 10
2.4.
Safety Precautions.................................................................................. 12
Features & Operating Condit ion ...................................................................... 14
3.1.
Brief Description ..................................................................................... 14
3.2.
Operating Condition ................................................................................ 14
4.
Standard Components ..................................................................................... 16
5.
Accessories ..................................................................................................... 17
6.
Composit ion .................................................................................................... 18
7.
Installation ....................................................................................................... 24
7.1.
Assembling the Instrument ...................................................................... 24
8.
Trial Operations ............................................................................................... 28
9.
Main Features .................................................................................................. 29
10. Ordinary Maintenance ...................................................................................... 30
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
11.
5
10.1.
Halogen Projection bulb .......................................................................... 30
10.2.
Protection fuses replacement................................................................... 32
10.3.
Cleaning & Disinfection ........................................................................... 33
EMC Infor mation .............................................................................................. 34
11.1.
Guidance and manufacturer’s declaration – electromagnetic emissions...... 34
11.2.
Guidance and manufacturer’s declaration – electromagnetic immunity ....... 35
11.3.
Guidance and manufacturer’s declaration – electromagnetic immunity ....... 37
11.4.
Recommended separation distances between portable and mobile RF
communications equipment and the EUT.............................................................. 39
11.5.
Immunity and Compliance Level .............................................................. 40
11.6.
Guidance and manufacturer’s declaration – electromagnetic immunity ....... 41
12. Electric Diagram............................................................................................... 43
13. Technical Specifications .................................................................................. 44
14. Service Information .......................................................................................... 46
15. Particular Information ……………………………………………………………………….48
6
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
1.
Introduction
1.1. Indication for use (intended use)
The SLIT LAMP, HS-7000 is intended for use in eye examination of the ant
eye
segments, from the cornea epithelium to the posterior capsule. It is used to aid in the
diagnosis of diseases or trauma which affects the structural properties of the anterior
eye segment.
1.2. Classification
-
-
Protection against electric shock: Class I
Applied Parts: Type B applied parts.
Protection against harmful ingress of water: Ordinary, IPX0
Degree of safety in the presence of a flammable anesthetics mixture with air
or with oxygen or with nitrous oxide: Not suitable for use in the presence of a
flammable anesthetics mixture with air or with oxygen or with nitrous oxide.
Mode of operation: Continuous
Light Hazard protection Classification: Group 2 by ISO15004-2:2007
Stationary: Do not try to move this equipment without help. This microscope is
heavy and should maintain stationary. Always get two persons to help lift this
unit
!
CAUTION
Federal law restricts this device to sale by or on the
of a physician
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
2.
7
Safety Information
2.1. Introduction
Safety is everyone’s responsibility. The safe use of this equipment is largely dependent
upon the installer, user, operator, and maintainer. It is imperative that personnel study
and become familiar with this entire manual before attempting to install use, clean,
service or adjust this equipment and any associated accessories. It is paramount that
the instructions contained in this manual are fully understood and followed to enhance
safety to the patient and the user/operator. It is for this reason that the following safety
notices have been placed appropriately within the text of this manual to highlight safety
related information or information requiring special emphasis. All users, operators, and
maintainers must be familiar with and pay particular attention to all Warnings and
Cautions incorporated herein.
!
WARNING
“Warning” indicates the presence o f a hazard that could result in severe perso nal injury,
death or substantial pro perty damage if ignored .
NOTE
“No te” describes information for the installation, operation, or maintenance of which is
impo rtant but hazard related if ignored.
!
CAUTION
“Cautio n” indicates the presence of a hazard that could result in minor injury, or
pro perty damaged if ignored.
8
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
2.2. Safety Symbols
The International Electro technical Commission (IEC) has established a set of symbols
for medical electronic equipment which classify a connection or warn of any potential
hazards. The classifications and symbols are shown below.
This applies only to the instrument that has the certification symbol printed explicitly on
the product label or sticker.
Save this instruction
I an d O o n po wer switch represent ON and OFF respectively.
Type B Isolated patient connection.
This symbol identifies a safety note. Ensure you understand
the function of this control before using it. Control
on
is described in the appropriate User ’s or Service M anual.
Identifies the po int where the system safety gro und is
fastened to the chassis. P rotective earth connected to
conductive parts of Class I equipment for safety purposes.
Ho t surface.
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
UL6 06 01 -1
CAN/CS A C22 .2
NO.601 .1
9
M EDIC AL EUIP M ENT
W ITH RESP EC T TO ELEC TRIC SHOCK
FIRE
AND
M E CH ANIC AL H AZ ARDS
ONLY IN ACCO RD ANCE W ITH U L 6 06011, AND C AN/CS A C22.2 NO.601.1
Disposal of your old appliance
W hen this crossed-o ut wheeled bin symbol is attached to a
product it means the product is co vered by the European
Directive 200 2/96/EC.
All electrical and electronic pro ducts should be disposed of
separately fro m the municipal waste stream via designated
collection facilities appo inted by the go vernment or the lo cal
autho rities.
The correct disposal of your old appliance will help prevent
po tential negative consequences for the environment and
human health.
4. For more detailed info rmation about disposal of your old
appliance, please contact your city office, waste disposal
service or the shop where yo u purchased the product.
Alternating Current
10
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
2.3. Environment factors
Avoid the following environments for operation or storage:
W here the equipment is expo sed to water vapor.
Don ’t operate equipment with a wet hand.
W here the equipment is expo sed to direct sunlight.
W here the temperature changes extremely.
Normal operating temperature range is fro m 10 °C to 40 °C,
Humidity is from 30% to 75% .
Altitude is from 700 to 1060hpa
W here it is near the heat equipment.
W here the humidity is extremely high o r there is a ventilation
problem.
W here the equipment is subject to excessive sho cks or
vibrations.
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
11
W here equipment is exposed to chemical material or
explosive gas.
Be careful not to be inserted dust, especially, metal.
Don ’t disassemble the pro duct or
respo nsible for it fo r nothing.
o pen.
We
aren ’t
Be careful not to close the fan lo cated on the lateral or back
side of the equipment.
Don ’t plug the AC power co rd into the outlet before the
connection between devices of the equipment is completed.
This can generate the defect.
P ull out the po wer cord with holding the plug, not the cord.
Avoid places where the ambient temperature falls below 10 ℃ or exceeds 40 ℃ for
normal operation, or below -10 ℃ or exceeds 40 ℃ (14℉-104℉) for transportation and
storage. Humidity should be maintained between 30 and
for normal operation,
transportation and storage. The atmospheric pressure in operation, transportation and
storage is from 700 to 1060hpa.
12
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
2.4. Safety Precautions
This equipment has been developed and tested according to safety standards as well
as national and international standards. This guarantees a very high degree of safety
for this device. The legislator expects us to inform the user expressively about the
safety aspects in dealing with the device. The correct handling of this equipment is
imperative for its safe operation. Therefore, please read carefully all instructions before
switching on this device. For more detailed informatio please contact our Customer
Service Department or one of our authorized representatives.
1.
This equipment must not be used (a) in an area that is in danger of explosions
and (b) in the presence of flammable, explosive, or vo tile solvent such as
alcohol, benzene or similar chemicals.
2.
Do not put or use this device in humid rooms. Humidity should be maintained
between 30 and 75% for normal operation. Do not expose the device to water
splashes, dripping water, or sprayed water. Do not place containers containing
fluids, liquids, or gases on top of any electrical equipment or devices.
3.
The equipment must be operated only by, or under direct supervision of a
properly trained and qualified person.
4.
Modifications of this equipment may only be carried out by Huvitz’s service
technicians or other authorized persons.
5.
Customer maintenance of this equipment may only be performed as stated in
the User’s Manual and Service Manual. Any additional maintenance may only
be performed by Huvitz’s service technicians or other authorized persons.
6.
The manufacturer is only responsible for effects on safety, reliability, and
performance of this equipment when the following requirements are fulfilled: (1)
The electrical installation in the respective room corresponds to the
specifications stated in this manual and (2) This equipment is used, operated,
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
13
And maintained according to this manual and Service Manual.
7.
The manufacturer is not liable for damage caused by unauthorized tampering
with the device(s). Such tampering will forfeit any rights to claim under
warranty.
8.
This equipment may only be used together with accessories supplied by
Huvitz’s. If the customer makes use of other accessories, use them only if their
safe usability under technical safety aspects has been proved and confirmed
by Huvitz or the manufacturer of the accessory.
9.
Only persons who have undergone proper training and instructions are
authorized to install, use, operate, and maintain this equipment.
10.
Keep the User’s Manual and Service Manual in a place easily accessible at all
times for persons operating and maintaining the equipment.
11.
Do not force cable connections. If a cable does not connect easily, be sure that
the connector (plug) is appropriate for the receptacle (socket). If you cause any
damage to a cable connector(s) or receptacle(s), let the damage(s) be repaired
by an authorized service technician.
12.
Please do not pull on any cable. Always hold on to the plug when
disconnecting cables.
13.
Before every operation, visually check the equipment for exterior mechanical
damage(s) and for proper function.
14.
Do not cover any ventilation grids or slits.
15.
Immediately turn off and unplug any equipment that gives off smoke, sparks,
strange noises, or odors.
16.
Power Supply Cord set (international) - (Detachable) Rated 10 A, 250 V. Plug
type CEE 7/VII, Connector type IEC 60320/C13, and Cord type H05VV-F3G,
min. 0.75 mm2, 3-conductor terminating in molded-on grounding type
attachment plug. <HAR> marked on the cord. Maximum 4.0 m long.
14
3.
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
Features & Operating Condition
3.1. Brief Description
The device works like all slit lamps:
Stereomicroscopic examination of the eye under the slit light.
Microscopic examination of the ocular fundus and posterior vitreou body (using
hruby’s lens).
These devices are designed for use by ophthalmologists and optometrists (within the
realms of their respective professions) for specific diagnostic procedures (biomicroscopic examination of the eye)
3.2. Operating Condition
l
As long as the slit lamp is in its original package it can be exposed to the
following environmental conditions for up to 15 weeks
shipping and storage
without risk of damage:
Temperature range: from –10˚
C to +40˚
C;
-
l
-
Relative humidity range: from 30% to75%;
The device is made to operate under the following environmental conditions:
Temperature range: from +10˚
C to +40˚
C;
Relative humidity range: from 30% to 75%;
The device neither generates nor receives electromagnetic interference when used
near other equipment. Therefore, no preventive or corrective measures are required
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
!
CAUTION
Because prolo nged intense light exposure can damage the retina, the use of the device
for ocular examinatio n sho uld no t be unnecessarily prolonged, and the brightness
setting sho uld not exceed what is needed to pro vide cl
visualizatio n o f the target
structures. This device should be used with filters that eliminate UV radiation
(<400nm) and, whene ver po ssible, filters that eliminate short - wavelength blue light
(<420nm).
The retinal exposure dose for a photochemical hazard is a pro duct o f the radiance and
the exposure time. If the value o f radiance were reduc
in half, twice the time would
be needed to reach the maximum exposure limit.
W hile no acute optical radiation hazards have been identified for slit lamps, it is
reco mmended that the intensity of light directed into
patient’s eye be limited to the
minimum level which is necessary for diagno sis. Infants, aphakes and persons with
diseased eyes will be at greater risk. The risk may also increased of the perso n being
examined has had any expo sure with the same instrument or any other ophthalmic
instrument using a visible light source during the previous 24 hours. This will ap ply
particularly if the eye has been exposed to retinal photo graphy
15
16
4.
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
Standard Components
The instrument is delivered in package. Taking it out
none of the following parts is missing.
the package, make sure that
l
A table top(N.B. the table top isn’t supplied with the slit lamp for twin table) on
which are placed: A SMPS box(15) including the main switch & a warning
light (13), Two sliding guides for the base with orthogonal movements(17), A
sliding plate for the position device(19), A drawer(16);
l
A base with orthogonal movements.
l
A microscope with either dual magnification or a system (31) including
eyepieces.
l
An optical group of the slit projector.
l
A head rest module (59).
l
A microscope arm (45).
l
This manual.
l
A set of accessories including; two wheels for the sliding guides(18); a setting
rod(43); a protective cover(46); a spare bulb 12V 30W
ogen bulb(53); two
protection fuses(48); a breath screen(19); a chin-rest paper(47);a hole
cover(45); a power cable; two patient’s handles(50)
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
5.
Accessories
The following standard accessories are provided with the instrument;
l
protection cover(46)
l
a setting rod(43)
l
spare bulbs
12V 30W Halogen bulb (53)
l
chin-rest paper(47)
l
spare fuses
250Vac T2.0AL
l
a breath screen(5)
l
power cable
[ Figure 1. Accessories ]
17
18
6.
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
Composition
1)
Fixation point
2)
Control lever for changing enlargement
3)
Removable eye-pieces
4)
Knob for clamping the breath screen
5)
Breath screen
6)
Control handle for the slit rotation 90-0-90
7)
Connecting plug of the projector lamp
8)
Knurled ring for filters insertion
9)
Joystick for lateral, longitudinal and vertical movements(x y z)
10) Base with orthogonal movements
11) Shaped tabletop
12) Warning light indicating the ignition of the SMPS is on
13) Main switch & Warning light
14) Luminosity selector
15) SMPS box
16) Drawer
17) Toothed guides
18) Wheel protection crankcases
19) Sliding plate
20) Knob to lock the projector
21) Scale for the projector position
22) Knob to lock the arm of the microscope
23) Hole cover
24) Knurled knob to lock the Lamp housing
25) Control handle for the vertical setting of the chin-rest
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
26) Locking pins for chin rest paper
27) Chin rest
28) Knobs to change the slit width
29) Pointer for the eye positioning
30) Forehead Rest
31) Microscope
32) Lamp socket
33) Knob to lock the base of the instrument
34) Knob to lock the microscope
35) Control handle for horizontal tilting
36) Control lever for vertical tilting
37) Microscope position stop
38) Graduated ring 90-0-90 determining the inclination of the slit during rotation
39) Lamp cover
40) fuse slots
41) Connecting plug
42) Fixation point connector
43) Setting rod
44) Microscope separation knob
45) Microscope arm
46) Protection cover
47) Chin rest papers
48) Guide screw
49) An optical group of the slit projector
50) Patient’s handle
51) Head rest fastening screw
52) Wheel
53) Halogen bulb 12V 30W
19
20
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
54) Bulb fastening knob
55) Mirror
56) Capture connector ( For the image system)
57) Capture switch
58) Luminosity selector connector ( Connect the Luminosity selector to the
SMPS)
59) Head rest module
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
[ Figure 2. Composition I ]
21
22
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
[ Figure 3. Composition Ⅱ]
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
[ Figure 4. Composition Ⅲ]
23
24
7.
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
Installation
NOTE
The appliances are always supplied with excellent packaging to be able to stand up to
all kinds of transport and standard storage conditions. P lease contact the suppliers if
any irregularities are fo und in the appliance due to transpo rt after unpacking
7.1. Assembling the Instrument
l
Put the table top on a very stable support. Block the wo parts together by
tightening the screws
[ Figure 5. Table Assembling ]
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
l
25
Place the head rest module (59) and make sure that its holes fit together with
those of the table top. Tighten the screw with the screw driver
[ Figure 6. Assembling the instrument I]
l
Place the base with orthogonal movements on the guides situated on the
upper part of the table top, checking that the wheels are in line. Then Place the
crankcase (59) and make sure that its holes fit together with those of the
toothed guides (17). Tighten the screw with the screw driver(+)
l
Assemble the microscope arm (45) on the Base with orthogonal move ments
(10).
l
Assemble an optical group of the slit projector (49) on the Base with orthogonal
26
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
movements (10). Then tighten the Guide screw with the screw driver(-)
l
Put the microscope(31) in the right position making sure that it is placed well in
the stop(37); then tighten it with the knob(34)situate the right side of the
microscope.
l
Fasten the breath screen(5) with the knob(4)
l
Insert the connecting cable into the socket.
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
[ Figure 7. Assembling the instrument Ⅱ]
27
28
8.
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
Trial Operations
l
Assemble the chin-rest paper (47) on the chin-rest (27).
l
Let the patient sit down comfortable with his chin on the chin-rest and his
forehead against the forehead-rest.
l
Lift or lower the chin-rest by moving the handle (25) so that the patient’s eyes
are in line with the notches on the chin-rest(29)
l
Switch the instruments on, press the switch (13). You will see the warning light
on (12).
l
Adjust the luminous intensity by moving the selector(14)
l
Frame and focus the eye to be examined by moving the lever(9)
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
9.
29
Main Features
Principal operative characteristics of the instrument:
l
Observation without settling or tiring and rapid change of enlargements.
l
Base with cross-wise movement (which can be stopped) commanded by a
single joystick for all adjustments(x y z)
l
Stereomicroscopic observation of the eye with enlargements 6X-10X-16X-25X40X (5 enlargements model).
l
Tilting 5˚
-10˚
-15 ˚
-20˚
l
Microscopy of the back part and of the posterior vitreous body by means of the
Hruby lens or a contact options. (Goldman lens).
l
Observation of the eye and valuation of the position of contact lenses in a
fluorescent light.
l
Tonometry with Goldman tonometer.
l
Measurement of the cornea diameter and contact lenses.
l
Survey which reveals the axis of the contact lens, tha
to the possible reading
of the rotation angle of the slit which includes all the meridians.
30
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
10. Ordinary Maintenance
!
WARNING
The repairs illustrated belo w sho uld all be carried out with the po wer cable
disco nnected from the main supply plug. P lease contact the suppliers for any other
problems that canno t be resolved by the o perations des ibed below.
!
CAUTION
P lease turn o ff the power switch before replacing lamps. P lease place lamps after
coo ling down. The heated lamp may burn your fingers.
NOTE
Don ’t to uch any o ther parts of glass tube with the bare fingers. Fingerprints, if any,
must be wiped off from the glass tube with alcohol
10.1. Halogen Projection bulb
To replace the Halogen projection bulb proceed as follow.
l
Before doing anything else, disconnect the plug from the main supply socket;
l
Remove the screws with the driver(24), Remove the cover(39),
l
Remove the Lamp socket(32) from the bulb stems;
l
Bulb fastening knob (54) to loosen the bulb stop
l
Remove the burnt out bulb; be careful , it could be very hot;
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
31
l
Replace it with a new one(12V30W Halogen) using the pl
touch the bulb whit fingers)
l
Fasten the bulb with the knob
l
Make sure that the stems of the bulb are completely inserted; insert the plug in
the main supply socket
[ Figure 8. Replace Halogen bulb ]
!
WARNING
Don ’t To uch to the Lamp Ho use, During the Operatio n.
It’s Heating up.
tic envelope(never
32
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
10.2. Protection fuses replacement
To replace the fuses proceed as follows:
l
The protection fuses are placed on the back of the SMPS, and inserted power
socket. Before doing anything else, disconnect the plu from the main supply
socket
l
Remove the burned-out fuses
l
Substitute the fuses and check
l
Replace the plug in the main supply socket.
[ Figure 9. Replace the fuse ]
!
CAUTION
Replace fuses with the same rating and type(250 Vac, T2 .0 AL)
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
33
10.3. Cleaning & Disinfection
l
To keep the device clean, apply clinical alcohol and cidex or cidex plus on a soft
cloth and scrub the body and the probe once a month. Do not use lacquer,
thinner, ethylene, or the oxidizing substance.
l
If the instrument is not in use, dust must be kept away by covering the
instrument with the supplied plastic cover. Dust accumulating during the
functioning of the instrument must be periodically removed with a very soft cloth
or with a small pump.
34
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
11. EMC Information
11.1. Guidance and manufacturer’s declaration – electromagnetic
emissions
The EUT is intended for use in the electromagnetic environment specified below.
The customer or the user of the EUT should assure that it is used in such an
environment.
Immunity test
Compliance
Electromagnetic environment guidance
RF Emissions
CISPR 11
Group 1
The EUT uses RF energy only for its
internal function. Therefore, its RF
emissions are very low and are not likely
to cause any interference in nearby
electronic equipment
RF Emissions
CISPR 11
Class B
The EUT is suitable for use in ail
establishments,
including
domestic
establishments
and
those
directly
connected to the public low-voltage power
supply network that supplies buildings
used for domestic purposes
Harmonic
emissions
IEC 61000-3-2
Class A
Voltage
fluctuations/
Flicker emissions
Complies
IEC 61000-3-3
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
35
11.2. Guidance and manufacturer’s declaration – electromagnetic
immunity
The EUT is intended for use in the electromagnetic environment specified below.
The customer or the user of the EUT should assure that it is used in such an
environment.
Immunity test
IEC 60601
Compliance
Electromagnetic
Test level
level
environment -guidance
Electrostatic
discharge (ESD)
IEC 61000-4-2
±6kV Contact
±8kV air
±6kV Contact
±8kV air
Floors should be wood,
concrete or ceramic tile.
If floors are covered with
synthetic material, the
relative humidity should
be at least 30%.
Electrical fast
transient/burst
IEC 61000-4-4
±2kV for power
supply lines
±
1kV
for
input/output
lines
±2kV for power
supply lines
± 1kV for
input/output
lines
Mains power quality
should be that of a
typical commercial or
hospital environment.
Surge
IEC 61000-4-5
±1kV
differential
mode
±2kV common
mode
±1kV differential
mode
±2kV common
mode
Mains power quality
should be that of a
typical commercial or
hospital environment.
Voltage
dips,
short
interruptions and
voltage
variations
on power supply
input lines
IEC 61000-4-11
<5% U?
(>95% dip in
U?)
for 0.5cycle
40% U?
(60% dip in
U? )
for 5 cycle
70% U?
(30% dip in U?)
for 25 cycle
<5% U?
(>95% dip in U?)
for 0.5cycle
40% U?
(60% dip in U? )
for 5 cycle
70% U?
(30% dip in U?)
for 25 cycle
<5% U?
(<95% dip in
Mains power quality
should be that of a
typical commercial or
hospital environment. If
the user of the EUT
image intensifier require
continued
operation
during power mains
interruptions,
it is recommended that
the
36
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
Power frequency
(50/60Hz)
magnetic field
IEC 61000-4-8
<5% U?
(<95% dip in
U? )
for 5 s
U? )
for 5 s
EUT image intensifier be
Powered
from
an
uninterruptible
power
supply or a battery.
3 A/m
3 A/m
Power
frequency
magnetic fields should
be at levels character
ristic of a typical location
in a typical commercial
or hospital environment.
NOTE U? is the a.c. mains voltage prior to application of the test level.
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
37
11.3. Guidance and manufacturer’s declaration – electromagnetic
immunity
The EUT is intended for use in the electromagnetic environment specified below.
The customer or the user of the EUT should assure that it is used in such an
environment.
Immunity
IEC
Complianc
test
60601
e
test
level
Electromagnetic environment - guidance
level
Conducted
RF
IEC
61000-4-6
Radiated
RF
IEC
61000-4-3
3 Vrms
150
kHz to
80MHz
3 V/m
80
MHz to
2.5GHz
3 Vrms
150 kHz to
80MHz
Portable and mobile RF communications
equipment should be used no closer to any
part of the EUT, including cables, than the
recommended
separation
distance
calculated from the equation applicable to
the frequency of the transmitter.
3 V/m
80MHz to
2.5GHz
Recommended separation distance
where P is the maximum output power
rating of the transmitter in watts (W)
according to the transmitter manufacturer
38
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
and d is the recommended separation
distance in meters (m).
Field strengths from fixed RF transmitters,
as deter-mined by an electromagnetic site
a
survey,
should be less than the compliance level in
b
each frequency range.
Interference may occur in the vicinity of
equipment marked with the following
symbol :
NOTE 1) At 80MHz and 800MHz, the higher frequency range applies.
NOTE 2) These guidelines may not apply in all situatio
Electromagnetic
propagation is affected by absorption and reflection from structures, objects and
people.
a
Field strengths from fixed transmitters, such as base
tations for radio
(cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM
radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.
To assess the electromagnetic environment due to fixed RF transmitters, an
electromagnetic site survey should be considered. If the measured field strength in
the location in which the EUT is used exceeds the applicable RF compliance level
above, the EUT should be observed to verify normal operation. If abnormal
performance is observed, additional measures may be necessary, such as reorienting or relocating the EUT.
b
Over the frequency range 150kHz to 80MHz, field strengths should be less than
[V1] V/m.
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
39
11.4. Recommended separation distances between portable and
mobile RF communications equipment and the EUT
This is intended for use in an electromagnetic environment
which radiated RF
disturbances are controlled. The customer or the user
the EUT can help Prevent
electromagnetic interference by maintaining a minimum
nce between portable
and mobile RF communications equipment (transmitters)
the EUT as
recommended below, according to the maximum output power of the communications
equipment.
Rated
maximum
output power
of transmitter
[W]
Separation distance according to frequency of transmitter [m]
150kHz to 80MHz
80MHz to
800MHz
800MHz to
2.5GHz
V1=3Vrms
E1=3V/m
E1=3V/m
0.01
0.116
0.1166
0.2333
0.1
0.368
0.3687
0.7378
1
1.166
1.1660
2.3333
10
3.687
3.6872
7.3785
100
11.660
11.6600
23.333
For transmitters rated at a maximum output power not listed above, the
recommended separation distance d in metres (m) can be estimated using the
equation applicable to the frequency of the transmitter, where p is the maximum
output power rating of the transmitter in watts (W) according to the transmitter
manufacturer.
NOTE 1) At 80MHz and 800MHz, the separation distance for the higher frequency
range applies.
NOTE 2) These guidelines may not apply in all situations. Electromagnetic
propagation is affected by absorption and reflection from structures, objects and
people.
40
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
11.5. Immunity and Compliance Level
Immunity test
IEC 60601 Test
Actual Immunity
Compliance
Level
Level
Level
Conducted RF
IEC 61000-4-6
3Vrms
150kHz to 80MHz
3Vrms
3Vrms
Radiated RF
IEC 61000-4-3
3Vrms
80MHz to 2.5GHz
3V/m
3V/m
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
41
11.6. Guidance and manufacturer’s declaration – electromagnetic
immunity
The EUT is intended for use in the electromagnetic environment specified below.
The customer or the user of the EUT should assure that it is used in such an
electromagnetic environment.
Immunity
IEC 60601
Compliance
test
test level
level
Conducted
RF
IEC
61000-4-6
3 Vrms
150 kHz to
80MHz
3 Vrms
150 kHz
80MHz
Radiated
RF
IEC
61000-4-3
3 V/m
80 MHz to
2.5GHz
3 V/m
80MHz to
2.5GHz
Electromagnetic environment guidance
to
The EUT must be used only in a
shielded location with a minimum RF
shielding effectiveness and, for each
cable that enters the shielded
location with a minimum RF shielding
effectiveness and, for each cable that
enters the shielded location
Field strengths outside the shielded
location from fixed RF transmitters,
as determined by an
electromagnetic site survey, should
a
be less than 3V/m.
Interference may occur in the vicinity
of equipment marked with the
following symbol:
42
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
NOTE 1) These guidelines may not apply in all situatio
Electromagnetic
propagation is affected by absorption and reflection from structures, objects and
people.
NOTE 2) It is essential that the actual shielding effectiveness and filter
attenuation of the shielded location be verified to assure that they meet the
minimum specification.
a
Field strengths from fixed transmitters, such as base stations for radio
(cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM
radio broadcast and TV broadcast cannot be predicted theoretically with
accuracy. To assess the electromagnetic environment due to fixed RF
transmitters, an
electromagnetic site survey should be considered. If the measured field strength
outside the shielded location in which the EUT is used exceeds 3V/m, the EUT
should be observed to verify normal operation.
If abnormal performance is observed, additional measures may be necessary,
such as relocating the EUT or using a shielded location with a higher RF
shielding effectiveness and filter attenuation.
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
12. Electric Diagram
43
44
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
13. Technical Specifications
MICROSCOPE
- HS-7000 (5x)
Type
Galilean converging binocular
Magnification
5 positions rotation drum
Eyepiece
12.5x (Option 10x)
Total magnification
6x, 10x, 16x, 25x, 40x(12.5x eyepiece )
or 5x, 8x, 12x, 20x, 32x( 10x eyepiece )
Real field of view
38.5, 24.0, 15.0, 9.0, 6.0 mm
Interpupillary adjust
55-80 mm
SLIT ILLUMINATION
Slit length
0.3-12 mm(continuous)
Slit width
0-12 mm(continuous)
Slit projection
1x
Aperture diaphragms
0.3/1/3/5/9/12 mm
Filters
cobalt blue,
absorption
Slit rotation
0˚
~180˚continuous
Angle of incidence
0,̊ 5,̊ 10,̊ 15,̊ 20˚
Patient’
s eye/mirror
surface working
distance
80 mm
red-free,
gray
and
heat-
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
BASE
Vertical Movement
Min. 28mm
Longitudinal Movement
Min. 78mm.
Lateral Movement
Min. 98mm
Fine base Movement
Min. 10mm
Power supply
100~240 V AC 50/60HZ 2.0A
Power consumption
70VA
Instrument Voltage
12V DC
Halogen Projection
bulb
12V 30W
Fixation point LED
3.4V 20mA
45
46
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
14. Service Information
Ho w to contact service: If there are any problems with the equipment, please follow the
steps belo w:
l
First of all, refer to the 10. M aintenance and 11. Tro ubleshooting sections according
l
If the pro blem persists, please contact the local distributor in your province or country
l
Befo re calling to the local distributor, you ’d better check these information such as
to the problem that you are encountered. And then follow the suggested sequences.
at first.
M o del and Serial Numbers. To do so, fill up the following table as soo n as you
purchase our product. You can lo ok up these information at any time. The serial
number is found o n the back of this unit. The serial number is unique to this unit.
You sho uld retain this manual as a permanent record of your purchase. P lease retain
your purchase receipt as your proof of purchase.
Date of P urchase:
Deal er’s Nam e:
Deal er Address:
Deal er P hone No . :
M odel No .:
Seri al No.:
l
If yo u can ’t contact with yo ur local distributo r, yo u can directly get in touch with the
service department of the HUVITZ using the phone number and the address written
in the belo w table.
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
How to Contact
HUVITZ Co., Ltd
Wri te us at:
Tel : +82-31 - 442-8 868
HUVITZ Co., Ltd.
F ax : +8 2 - 31-442-8 619
Huvitz B/D, 68 9 - 3 Geumjeong - dong
URL : http://www.huvi tz.co m
Gunpo - si Gyeo nggi - do, South Korea
4 35 -86 2
e -m ail: [email protected] huvi tz.com
47
48
SLIT LAMP HS- 7000------------------- ----------------------------------------------------------------
15. Particular Information
15.1. Relative spectral output graph
(1) Halogen Lamp
(2) Fixat ion Lamp
------------------------------------------------------ -----------------------------SLIT LAMP HS-7000
Note: this graph be shown for the beam after it exist the instrument,
when the instrument is operating at maximum light intensity and
maximum aperture.
!
CAUTION
“CAUTION – The light emitted from this instrument is potentially
hazardous. The longer the duration of exposure, the greater the risk of
ocular damage. Exposure to light from this instrument
operated
at maximum output will exceed the safety guideline after
_80seconds__
(e. g. 80seconds for source halogen lamp, 151057 seconds for
fixation lamp,).”
49
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement