ZENITH SERIES - Graham Field

ZENITH SERIES - Graham Field
ZENITH
SERIES
INSTRUCTIONS FOR USE
SERVICE MANUAL
To avoid personal injury or damage to bed,
please read all sections pertaining to
the bed model before use.
ETL/UL/CSA APPROVED
UL 60601-1
IEC 60601-2-38
CSA 22.2 601.1
GF Health Products, Inc. - www.grahamfield.com
Zenith Series Service Manual 999-0844-190D - DEC. 2013
This service manual covers the following Zenith Models:
76” & 80” Full Electric with Pedal Lock Caster System & Grid Decks = ZZ98174
Basic American Medical Products
336 Trowbridge Drive
Fond du Lac, WI 54937
For Zenith 9000 Bed Service Parts
please contact our Customer Service Department
at 1-800-365-2338
GF Health Products, Inc.
2935 Northeast Parkway
Atlanta, GA 30360
www.grahamfield.com
To order a Zenith 9000 Bed
please contact a Graham Field Sales Representative
at 1-800-554-9215
IMPORTANT NOTICE
GF Health Products, Inc. is not responsible for typographical errors.
All illustrations, specifications, packaging, and warranties contained in this Service Manual
are based on the latest product information available at the time of printing.
The most current product information can be found online at www.grahamfield.com.
Please check all parts for shipping damage and test before using.
In case of damage, DO NOT USE.
ZENITH SERIES
TABLE OF CONTENTS
IMPORTANT INFORMATION REGARDING YOUR BED
Safety & Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5
Entrapment/Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Recommended Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Warning Labels and Environmental Specifications . . . . . . . . . . 7
SECTION A - BED SET-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Unpacking Your Bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Headboard and Footboard Installation . . . . . . . . . . . . . . . . . . .10
Standard Mattress Retainer Installation . . . . . . . . . . . . . . . . . .11
Standard Wallsaver Installation . . . . . . . . . . . . . . . . . . . . . . . . .12
Plugging in Your Staff/Nurse Control . . . . . . . . . . . . . . . . . . . . .13
Pendant/Hand Controller Operation . . . . . . . . . . . . . . . . . . . . .14
Staff/Nurse Control Operation . . . . . . . . . . . . . . . . . . . . . . . . . .15
SECTION B - ASSIST DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Optional Pivoting Assist Bar Installation . . . . . . . . . . . . . . . . . .17
Optional Half Rail Installation . . . . . . . . . . . . . . . . . . . . . . . . . .18
Optional Trapeze Support Installation . . . . . . . . . . . . . . . . . . . .19
SECTION C - MECHANICAL/ELECTRICAL INFORMATION . . . . . . . 20
SECTION D - SERVICE/REPLACEMENT PARTS . . . . . . . . . . . . . . . 24
SECTION E - TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . 33
WARRANTY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
LABEL SYMBOL DEFINITIONS
!
!
Consult
Accompanying
Documents
Safe
Working
Load
GF Health Products, Inc. - www.grahamfield.com
Double
Insulated
Protected
Grounded
Device
Type B
Equipment &
Applied Parts
3
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
IMPORTANT SAFETY AND WARNING INFORMATION
!
This product is a variable height, adjustable mattress
platform, which will provide comfort and convenience
for residents/patients and caregivers in long term
care settings.
!
The MAXIMUM SAFE WORKING LOAD for the
Zenith 9000 Bed with weight evenly distributed,
including bedding, resident/patient, support surface,
and all accessories, is 600 lbs.
!
NEVER operate the bed if a Power Cord or Plug is
damaged or not working properly. Contact qualified
Service Personnel for examination and repair. Always
unplug the Power Cord when performing any maintenance on the bed.
!
Beds manufactured by Basic American Medical Products
are designed for use within an institutional healthcare
environment (i.e. assisted living, skilled nursing, transitional care, rehabilitational care, etc.).
!
DO NOT use the assist devices as push handles for moving
the bed. Assist devices can be deformed or broken if
excessive side pressure is exerted. Assist devices are not
meant for patients considered as high risks for entrapment
(i.e. patients with pre-existing conditions such as
confusion, restlessness, lack of muscle control, altered
mental status, either organic or medicinal, or a combination thereof). Additional safety measures should be
considered for such high-risk patients.
!
NEVER permit more than one (1) person on/in the bed
at any time.
!
Body weight should be evenly distributed over the
sleeping surface of the bed. DO NOT allow the patient
to lay, sit, or lean in such a way that their entire body
weight is placed only on the raised head or foot sections
of the bed. This especially applies when repositioning
or transferring a patient in or out of the bed. Increased
risk may occur when the patient’s size and/or weight are
inappropriate for the bed’s dimensions or weight capacity.
!
DO NOT open assemblies such as the Actuators, Hand
Control, or Control Box. If unauthorized personnel
perform work on these components, the manufacturer’s
warranty becomes void.
!
DO NOT use unauthorized parts, accessories, or
adaptors other than those specified/authorized by
GF Health Products, Inc.
!
When operating the HI/LO, Knee, or Back Functions
of the bed, ALWAYS ensure that the confined individual
is positioned properly within the confines of the bed.
DO NOT let any extremities protrude over the side or
between the bed rails when performing these functions.
!
Risk of entanglement or injury may occur if the mattress
used with mattress retainers does not fill the entire width
between stops or which compresses to less than 1.50
inches under user’s weight.
!
DO NOT lower the bed when objects are beneath it.
Failure to inspect under the bed can result in damage
to property or personal injury.
!
!
The bed’s Pendant Cord MUST BE ROUTED AND
SECURED PROPERLY to ensure it does not become
entangled and eventually severed during use. Also
make sure all electrical cords DO NOT get tangled
around the bed, side rails, or legs during transport or
normal operation of the bed.
Mattress must be properly sized to fit the mattress support
platform and must remain centered on the support platform
relative to State and Federal guidelines. Recommended
minimum dimensions of mattress is 35 inches wide and
6 inches deep. Length should match the mattress support
platform. Use of an improperly fitted mattress could
result in injury or death.
!
IMPORTANT: Powered air mattress surfaces may pose
a risk of entrapment. Prior to use, ensure the therapeutic
benefits outweigh the risk of entrapment.
!
The bed is intended for use, storage, and transport within
a temperature range of -40˚C to +60˚C. It has a waterresistance rating of IPX6 and IS NOT to be powerwashed or submersed.
!
When using nasal-type or masked-type administering
equipment, all oxygen or air tubing MUST BE ROUTED
AND SECURED PROPERLY to ensure that the tubing
does not become entangled and eventually severed
during the normal operation of the bed.
!
Keep all moving parts free of obstructions (i.e. blankets/
sheets, heating blankets/pads, wiring, etc.).
GF Health Products, Inc. - www.grahamfield.com
4
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
IMPORTANT SAFETY AND WARNING INFORMATION
!
!
The head/back and knee/foot decks can be lifted freely
by hand for easy cleaning access when patients are not
in the bed. If you lift the head/back or knee/foot deck
for any reason, please take great care when lowering
back down to the prone position - make sure that all
body parts are clear of the space between the deck and
the bed prior to slowly lowering any deck manually. To
avoid injury, DO NOT LET DECKS FALL FREELY
FROM ANY ANGLE.
Notice for California Customers California Proposition 65 WARNING: This product
contains a chemical known to the State of California to
cause cancer and reproductive or developmental harm.
!
Proper routing and tie-off of electrical cabling, especially
the power cord, is essential for proper operation and to
ensure safety from electrical shock. In the event you are
replacing any electrical cabling on your bed, you must
make sure the cables are free from any pinch points,
obstructions, or stretched so tight that they may come
loose or become damaged. In addition, cables should
be tied off in such a way to secure them and keep them
free from tangling on any part of the bed during normal
operation. Refer to your service manual’s electrical
section for proper cable routing.
ENTRAPMENT & COMPLIANCE INFORMATION
On April 10, 2006, the FDA (U.S. Food and Drug Administration) released long-awaited guidelines for reducing the risk
of bed entrapment: “Hospital Bed System Dimensional and
Assessment Guidance to Reduce Entrapment”. The new Guidance
identifies potential entrapment areas and those body parts most
at risk for entrapment; provides design criteria for manufacturers
of new hospital/convalescent beds; recommends particular test
methods to assess the conformance of existing hospital/convalescent bed systems; and answers frequently-asked questions
about entrapment issues.
The new Guidance was a result of a long-standing collaboration
between the FDA and the Hospital Bed Safety Workgroup
(HBSW), formed in 1999. GF Health Products, Inc’s LongTerm Care Bed division: Basic American Medical Products, is
an HBSW charter member. As a result of our commitment to
product safety, all our current long-term care beds have been
strictly tested and conform to the new FDA Guidance.
The guidelines set forth by the FDA Guidance layout specific
dimensional limitations on potentially injury-threatening gaps
and spaces that can occur between bed system components,
such as rails, when not properly installed. GF Health Products,
Inc. and Basic American Medical Products have conformed
to these guidelines from a manufacturing aspect. However,
entrapment issues can often arise when a healthcare provider/
facility has not correctly assembled the components on a bed.
It is essential that the provider/facility fully understand their
responsibility in complying to the guidelines set forth by the
GF Health Products, Inc. - www.grahamfield.com
FDA in order to avoid injury. To that end, we have provided
the FDA’s web address at right as a resource for understanding
and following these guidelines for the safety of patients/residents.
It is also essential to have the correct bed components/accessories that correspond with the needs of the patient/resident
and the particular bed you have purchased. Matching the correct
bed component that correlates with the regulatory guidelines can
be a daunting task. Our sales team at GF Health Products, Inc.
and our friendly Customer Service Representatives at Basic
American Medical Products can help you sift through the wide
array of compliance and bed options. We will help you determine
which bed/bed part is best for the patient’s/resident’s particular
needs and help you with any compliance issues.
The Zenith 9000 bed and accessories listed in this
manual are in full compliance with FDA guidelines
for reducing the risk of bed entrapment: “Hospital
Bed System Dimensional and Assessment Guidance
to Reduce Entrapment”.
Details can be found at www.fda.gov.
5
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
Regular maintenance of the Long Term Bed is necessary to ensure continuing proper and safe operation.
Please read and observe the following recommended maintenance schedule.
RECOMMENDED
INSPECTION PERIODS
Inspect
Every
on Receipt 3 Months
ITEM
Every
6 Months
Maintenance Inspection of All Components at Receipt of Shipment
Make sure all parts/components are included (Please see “Unpacking The Bed”).
X
Check all bed components for obvious damage.
X
Inspect the power supply cord for any cuts and/or damage.
X
Check to see all actuator/motor cords are routed and connected properly to the control box.
X
Mechanical Inspection of Assemblies
Inspect all welds on the sleeping surface, frame, and base assemblies for stress fractures.
X
Inspect all fasteners for wear and looseness.
X
IMPORTANT: Lubricate all pivot points, actuator/motor clevis pins, and control arm clevis
pins as needed. White Lithium Grease is recommended.
X
Mechanical Inspection of Casters & Pedal Locking Mechanism
Check the pedal locking mechanism to make sure it engages and disengages properly.
X
Check the bottom foot pads on the foot end casters, making sure they are clean of debris
and undamaged. Replace if needed.
X
Check all casters to ensure that they roll properly and are unobstructed.
X
Electrical Inspection of Control Box, Pendant, and Staff Control
Check the external power cord that plugs into the control box for any chafing, cuts, or wear.
Replace if damaged.
X
Make sure all attaching hardware is securely tightened.
X
Check all electrical connections for any wear or fractures.
X
Check the external backup battery (if you have one). Replace if needed.
X
Check the pendant cord for any chafing, cuts, or wear.
X
Check all pendant functions - check to make sure each button and associated function work
properly (i.e. head section rises when the Head Up button is activated).
X
Electrical Inspection of Actuators/Motors
Check the actuator/motor cords for any chafing, cuts, or wear.
X
Check the range of movement on all motors to ensure they do not bind in the Full Up or
Full Down positions.
X
GF Health Products, Inc. - www.grahamfield.com
6
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
The following warning labels have been placed on the bed to help protect you and the bed from damage.
Please do not remove any labels from the bed.
WARNING!
CAUTION
DO NOT LOWER BED WHEN OBJECTS ARE
BENEATH BED. FAILURE TO INSPECT UNDER
BED CAN RESULT IN DAMAGE TO PROPERTY
OR PERSONAL INJURY.
ATTENTION:
S’assurer de ne pas faire descendre le lit
lorsque des objets se trouvent sous le lit. Ne
pas inspecter le dessous du lit pourrait entrainer
des dommages materiels et des risques de
blessures.
THIS BED IS SUITABLE FOR USE ONLY WITH
OXYGEN ADMINISTERING EQUIPMENT OF
THE NASAL OR MASK TYPE OR A TENT
COVERING ONLY THE UPPER HALF (HEAD
END) OF THE BED. OXYGEN TENT CANOPIES
SHOULD NOT EXTEND BELOW BED SPRING
LEVEL. LOCK HAND CONTROL AT FOOT OF
BED WHEN USING OXYGEN ADMINISTERING
EQUIPMENT.
ATTENTION:
WARNING!
DO NOT LOWER BED WHEN
OBJECTS ARE BENEATH BED.
FAILURE TO INSPECT UNDER
BED CAN RESULT IN DAMAGE
TO PROPERTY OR PERSONAL
INJURY.
CE LIT PEUT ETRE UTILISE UNIQUEMENT
AVEC UN EQUIPMENT DESTINE A
L’ADMINISTRATION D’OXYGENE DE TYPE
NASAL OU MASQUE OU AVEC UNE TENTE
RECOUVRANT SEULEMENT LA MOTTIE
AVENT (TETE) DU LIT. LES COTES DE LAS
TENTE OXYGENE NE DOIVENT PAS SE
PROLONGER PLUS DAS QUE LA SOMMIER
DU LIT.
ENVIRONMENTAL SPECIFICATIONS AND STORAGE
AND RFI INFORMATION
Operating Conditions
Operation of the bed is based on the following conditions: Ambient Temperature of +10˚C to +40˚C; Relative Humidity of 30%
to 75% (Non-condensing); Atmospheric Pressure of 700hPa to 1060hPa; and a Splash Protection of IEC 60529.
Storage
Storage of the bed is based on the following conditions: Ambient Temperature of -10˚C to 70˚C; Relative Humidity of 10% to
100%; and an Atmospheric Pressure of 500hPa to 1060hPa.
Radio Frequency Interference (RFI)
RFI influences most electronic equipment. Caution should be exercised with regard to the use of portable communications
equipment in the area around such equipment. If RFI causes erratic behavior, shut the bed off immediately. Leave it off while
the transmission is in progress.
GF Health Products, Inc. - www.grahamfield.com
7
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
SECTION A
ZENITH 9000
Bed Set-up
Instructions
GF Health Products, Inc. - www.grahamfield.com
8
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
UNPACKING THE BED
DISCARD
1. Middle Foam Block
2. Large Block
3. Large Cable Tie - CUT
4. Notched 2 x 4 Board
5. Small Side Blocks
6. Foam Wrapping
7. End Caps with Foam
8. Notched Leg Foam
9. Small Cable Tie - CUT
• Make sure all parts/components are included.
• Check all bed components for obvious damage.
• Inspect the Power Supply Cord for any cuts and/
or damage.
• Check to see all actuator/motor cables are routed
and connected
properly to the
control box.
KEEP
10. Wireform Wallsaver
11. Two Mattress Retainers
12. Service Manual/Documents
13. Pendant Holster
(attached to pendant)
NOTE:
END OF POWER CABLE IS COILED
FOR SHIPPING AND TIED, WITH
CABLE TIE, TO GRID WIRE ALONG
WITH PENDANT, PENDANT CABLE
& HOLSTER.
2
1
PLEASE CUT AND DISCARD CABLE
TIE AROUND CABLES WHEN YOU
UN-PACK THE BED.
6
10
4
2
3
7
9
6
5
7
11
11
Cut and
discard
cable tie.
8
13
12
8
GF Health Products, Inc. - www.grahamfield.com
ALSO
DISCARD TOP
AND BOTTOM
CARTONS
9
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
HEAD- AND FOOTBOARD ASSEMBLY
1. HEADBOARD INSTALLATION
2. FOOTBOARD INSTALLATION
• The headboard comes with four pre-installed
inserts - consider this the inside of the board.
• The footboard comes with four pre-installed
inserts - consider this the outside of the board.
• Position 2 mounting tubes on the outside of
the headboard with “L” facing inward.
• Position 2 mounting tubes on the inside of the
footboard with “L” facing outward.
• Align the top hole of the mounting tubes with
the top holes in the headboard.
• Align the top hole of the mounting tubes with
the top holes in the footboard.
• Insert a 40mm hex drive bolt through each of
the top holes and bottom holes and screw into
each insert. Tighten with the Hex Allen wrench
included in the kit.
• Insert a 40mm hex drive bolt through each of
the top holes and bottom holes and screw into
each insert. Tighten with the Hex Allen wrench
included in the kit.
• Slide the “L” portions of the Mounting tubes
into the hollow ends of the main frame rails,
at the head deck end.
• Slide the “L” portions of the Mounting tubes
into the hollow ends of the main frame rails,
at the foot deck end.
• FOR 80” BEDS: Slide the mounting tubes in
until the first tube hole lines up with the first
rail hole. See sample below.
• FOR 80” BEDS: Slide the mounting tubes in
until the first tube hole lines up with the second
rail hole. See sample below.
• FOR 76” BEDS: Slide the mounting tubes in
until the first tube hole lines up with the second
rail hole. See sample below.
• FOR 76” BEDS: Slide the mounting tubes in
until the first tube hole lines up with the third
rail hole. See sample below.
HEADBOARD
FOOTBOARD
Inserts
on inside
CENTER
OF BED
Inserts
on outside
40mm
Bolts
40mm
Bolts
CENTER
OF BED
76” hole position
(3rd hole in)
76” hole position
(2nd hole in)
80” hole position
(1st hole in)
1st hole
IMPORTANT:
76” OR 80”HEADBOARD &
FOOTBOARD POSITIONS
MUST MATCH RETAINER
& WALLSAVER POSITIONS.
PLEASE SEE PAGES 11-12.
GF Health Products, Inc. - www.grahamfield.com
80” hole position
(2nd hole in)
1st hole
NOTE: The first hole at the foot end is reserved for
attaching the Optional 4” pan extension.
10
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
STANDARD MATTRESS RETAINER INSTALLATION
(Using 2 Retainers 999-0844-124)
1. Determine if you need to position your bed in an 80” or 76”
configuration (80” outside holes; 76” inside holes - see
Closeups A & B).
4. On the head end, carefully squeeze the Mattress Retainer ends
inward, toward the center of the retainer, and insert the ends
into the proper holes (see Closeups A & B).
2. On the foot end, carefully squeeze the Mattress Retainer
ends inward, toward the center of the retainer, and insert
the ends into the proper holes (see Closeups A & B).
5. Lay the Mattress Retainer down so that the elbows rest on the
decks and the long cross rod is on the foot end side as shown.
3. Lay the Mattress Retainer down so that the
elbows rest on the decks and the long cross
rod is on the foot end side as shown.
CLOSEUP A:
INSERT HEAD END
MATTRESS RETAINER
CLOSEUP B:
INSERT FOOT END
MATTRESS RETAINER
Ou
Ins tside
ide
h
ho oles
les
f
for or 80
76 ” B
” B ed
ed s
s
IMPORTANT
MAKE SURE ALL THREE ADJUSTABLE PARTS
ARE PROPERLY POSITIONED FOR 76” OR 80”
CONFIGURATIONS (SEE PAGES 10 AND 12)
!
Be sure to use a mattress that is properly sized to fit
the sleep deck, which will remain centered on the deck
relative to State and Federal Guidelines. Use of an improperly fitted mattress could result in injury or death.
GF Health Products, Inc. - www.grahamfield.com
!
Use a properly sized mattress in order to minimize
the gap between the side of the mattress and assist
devices. This gap must be small enough to prevent
resident/patient from getting his/her head or neck
caught in this location.
11
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
Zenith SeRieS
STANDARD WIREFORM WALLSAVER INSTALLATION
WALLSAVER ASSEMBLY
1. Position the Wireform Wallsaver (Part 999-0844-180) with bent
end facing upward and tab ends facing inward as shown at right.
2. Determine the position desired (See bottom of page).
HEAD END
3. Gently squeeze the tab ends of the wallsaver inward toward the
center of the wallsaver and, holding the tabs parallel with the slots
in the caster bases (See DETAIL A), slide the tabs into the slots
while letting the wallsaver gently expand outward.
6WDUWZLWKWDEKHOG
KRUL]RQWDOO\
WALLSAVER POSITIONS
1. The Zenith 9000 wallsaver features
3 positions for easy reconfiguration
- 76”, 80”, and Trapeze.
2. For 76” beds, position the wallsaver
ends in the caster base slots closest
to the FOOT end of the bed. For 80”
beds, position the wallsaver ends
in the MIDDLE slots on the bases.
GF Health Products, Inc. - www.grahamfield.com
76” Bed Wallsaver
Position w/o Trapeze
'(7$,/%
%HQGIDFHVXSZDUG
WALLSAVER REMOVAL
1. To remove or move the Wireform
Wallsaver to a new position, raise
the wallsaver off the floor until
the end tabs are horizontal.
2. Squeeze the ends toward the
center of the wallsaver until the
end tabs slide out of the caster
base slots.
76” Bed Wallsaver
Position w/Trapeze or
80” Bed w/o Trapeze
80” Bed Wallsaver
Position w/Trapeze
HEAD END
3. If you have an optional Trapeze unit
on a 76” bed, position the wallsaver
ends in the MIDDLE slots on the
caster bases. For 80” beds position
wallsaver in slots closest to HEAD.
Finish
with
(QGZLWK
Wallsaver
:DOOVDYHU
resting
on
UHVWLQJRQ
floor
IORRU
:LUHIRUP:DOOVDYHU
FOOT END
'(7$,/$
4. Turn the wallsaver downward until it rests on the floor (See
Detail B).
12
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
PLUGGING IN THE FOOTBOARD NURSE/STAFF CONTROL
STEP 1 - ATTACHING THE FOOTBOARD
You can order an optional Staff Control for the Zenith 9000 which includes a Staff Control Assembly and Shroud Cover
pre-installed to the Footboard at the manufacturing facility.
Staff Control
Assembly
To attach the Footboard assembly (with Staff Control) to the main
frame rails, please see the instructions on Page 10 of this manual.
STEP 2 - CONNECTING THE CABLES
Please refer to DETAIL A shown below.
a. At the foot end, unplug the Black Staff Control cable
from the end of the T-Cable. (Cables were attached
for shipping.)
b. Insert the phone jack plug on the male end of the
staff control cable into the cylindrical plug of the
Black Control Cable that extends out the foot end.
Make sure the phone jack is positioned properly
inside the cable.
Phillips Screws
attach Shroud
& Staff Control
Assembly from
inside of board
FOOT
END
Shroud
(Cable Cover)
Cable Tie Staff
Control Cables
to right Mounting
Tube
c. Insert the T-Cable end (extending out the foot end
with phone jack) into the cylindrical plug of the female
staff control cable. Make sure the phone plug is
seated properly inside the female plug.
d. Screw on the round lock cap onto
the Staff Control’s female plug and
short Black Control Cable plug.
(see DETAIL B).
Footboard
with cutout
SEE PAGE 10 OF THIS
MANUAL FOR PROPER
ASSEMBLY OF ELBOW
MOUNTING BRACKETS
(TUBES) & FOOTBOARD
Loop Male Staff Control Cable
and cable tie through mounting
tube hole with Female Staff
Control Cable
Female end of Staff Control Cable plugs into T-Cable
End of T-Cable at foot end - WHITE
(“T” runs on either side of Seat Pan
for attaching your Hand Controller)
Male end of Staff Control Cable plugs into short Black Control Cable
DETAIL A:
CLOSEUP OF STAFF
CONTROL CABLE CONNECTION
GF Health Products, Inc. - www.grahamfield.com
Short Black Control Cable running
from Control Box
DETAIL B:
MAKE SURE LOCK END
CAPS ARE SCREWED
ON SECURELY
13
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
ZENITH 9000 PENDANT/HAND CONTROLLER OPERATION
The hand controller comes standard on the Zenith 9000 series and can
be plugged into either side of the bed. The plug features a
lock-on cap. A pendant holster for attaching to optional
assist devices is also provided.
2
1
HAND PENDANT OPERATION
4
3
1
HEAD DECK ANGLE UP BUTTON
2
HEAD DECK ANGLE DOWN BUTTON
3
HI/LO UP BUTTON (RAISE ENTIRE BED)
4
HI/LO DOWN BUTTON (LOWER ENTIRE BED)
5
KNEE & FOOT DECK ANGLE UP BUTTON
6
KNEE & FOOT DECK ANGLE DOWN BUTTON
6
5
HAND PENDANT
Part #999-0808-305
(Bed comes shipped with
Alligator Clip attached to
pendant cable. To order
a replacement pendant,
please see page 25.)
Pendant Holster
999-0791-000
comes standard
with the Zenith
7000 bed.
The Pendant
cable has a
phone jack
connector.
NOTE:
THE ZENITH 9000 PENDANT CAN BE PLUGGED INTO THE T-CABLE PLUGS ON EITHER SIDE OF THE BED FOR
EASY ACCESS. THE OPPOSITE SIDE OF THE T-CABLE SHOULD ALWAYS HAVE THE PROVIDED CAP ATTACHED
FOR SAFETY.
IN ORDER TO MAXIMIZE THE EASE OF USE, AS WELL AS THE LONGEVITY OF THE ZENITH BED, THE MICROPROCESSOR CONTROLLED CONTROL SYSTEM MONITORS ALL HANDSET AND NURSE CONTROL INPUTS. IT IS
INTENDED FOR USE BY THE PATIENT TO MAXIMIZE COMFORT OR BY THE CAREGIVER FOR REPOSITIONING.
TO DETER MISUSE BY A PATIENT, IF THE SYSTEM DETECTS REPEATED BUTTON OPERATIONS, IT WILL BLOCK
THE NEXT SIGNALS TO ENSURE THE WELLBEING OF THE PATIENT AND TO PROTECT THE SYSTEM. SHOULD
THIS OCCUR, THE USER WILL NOTICE A TWO (2) SECOND DELAY WHEN DEPRESSING A FUNCTION OR CAN WAIT
FOR TWO (2) SECONDS BEFORE OPERATING THE BED AGAIN.
GF Health Products, Inc. - www.grahamfield.com
14
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
BED OPERATIONS - NURSE/STAFF CONTROL PANEL
When you purchase your boards directly from our company, you have the option of ordering a Nurse/Staff Control Assembly
which would come pre-installed into the footboard at the manufacturing facility. Operations are listed below.
2
1
4
5
3
1
SELECT/HOLD BUTTON
9
8
6
7
12
10
13
11
HEAD/BACK FUNCTIONS
1. To raise the head/back deck to upright angle press Select #1 & #2
2. To lower the head/back deck to horizontal press Select #1 & #3
3. To lockout the head/back pendant function press Select #1 & #4
Lockout light #5 will glow.
4. To unlock the head/back pendant function press Select #1 & #4
Lockout light #5 will go out.
2
HEAD/BACK UP BUTTON
3
HEAD/BACK DOWN BUTTON
4
HEAD/BACK LOCKOUT BUTTON
5
HEAD/BACK LOCKOUT LIGHT
6
HI/LO (HORZ.) UP BUTTON
7
HI/LO (HORZ.) DOWN BUTTON
8
HI/LO (HORZ.) LOCKOUT BUTTON
9
HI/LO (HORZ.) LOCKOUT LIGHT
5. To raise the bed horizontally (HI/LO Up) press Select #1 & #6
6. To lower the bed horizontally (HI/LO Down) press Select #1 & #7
7. To lockout the HI/LO pendant function press Select #1 & #8
Lockout light #9 will glow.
8. To unlock the head/back pendant function press Select #1 & #8
Lockout light #9 will go out.
10
FOOT/KNEE UP BUTTON
FOOT/KNEE FUNCTIONS
11
FOOT/KNEE DOWN BUTTON
12
FOOT/KNEE LOCKOUT BUTTON
13
FOOT/KNEE LOCKOUT LIGHT
GF Health Products, Inc. - www.grahamfield.com
HI/LO FUNCTIONS
9. To raise foot/knee decks to upright angle press Select #1 & #10
10.To lower foot/knee decks to horizontal press Select #1 & #11
11.To lockout the foot/knee pendant function press Select #1 & #12
Lockout light #13 will glow.
12.To unlock the head/back pendant function press Select #1 & #12
Lockout light #13 will go out.
15
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
SECTION B
ASSIST DEVICES
Model ZZ98174
GF Health Products, Inc. - www.grahamfield.com
16
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
OPTIONAL PIVOT ASSIST BAR INSTALLATION & OPERATION
KIT ZA85400 - (Sample shows bar positioned on left side of bed)
1. At the head end of the bed, position the Pivoting Assist Bar (#2)
bracket over the Head Deck (#1) frame and align the two holes
in the Assist Bar bracket with the two holes in the frame rail on
either side of the head deck.
Position the Assist Bar
Bracket ON TOP of the
Deck Frame, aligning
holes in the bracket with
holes in the frame.
2. From the outside, insert the Clevis Pins (#3) through the
holes in the pivot bracket and deck frame.
+($'
(1'
3. From the inside, insert a Hair Pin Clip (#4) through
each of the small holes in the clevis pins.
1
D
3
D
3
PLEASE ORDER KIT # ZA85400. KIT INCLUDES ONE PIVOTING
ASSIST BAR ASSEMBLY AND TWO LANYARD ASSEMBLIES
WITH CLEVIS PINS AND HAIR PIN CLIPS. (A STATIONARY ASSIST
BAR IS ALSO AVAILABLE AS AN OPTION - KIT # ZA85000).
E
4
E
4
THE ASSIST BAR CAN BE POSITIONED ON EITHER THE RIGHT
SIDE OR LEFT SIDE OF THE HEAD DECK. IT IS NOT OFFERED
FOR THE FOOT END OF THE BED.
1. To release the pivoting assist bar from its
vertical lock position, hold onto the top of
the bar with one hand and slightly pull out
the black knob on the outside of the pivot
assembly with the other hand to release
the locking mechanism. For ease of patient
access, it is recommended that you pivot
the rail toward the headboard until it stops
and rests in place.
PIVOTING ASSIST BAR OPERATION
+($'
(1'
5HFRPPHQG
3LYRW7RZDUG
+HDGERDUG
2. To set the assist bar back to its upright
locked position, grab the top of the assist
bar with one hand and pivot the assembly
upward until the black knob mechanism
snaps into place, locking the assist bar
vertically.
%ODFN.QREWR
/RFNRU5HOHDVH
+($''(&.
6/((3685)$&(
+($'
'(&.
(1'
!
2
FOR OPTIMUM SAFETY, MAKE SURE
FINGERS ARE CLEAR OF THE SIDES
OR UNDERNEATH THE PIVOTING
ASSEMBLY WHEN POSITIONING THE
ASSIST BAR UP OR DOWN.
GF Health Products, Inc. - www.grahamfield.com
!
PLEASE MAKE SURE THE PIVOTING
ASSIST BAR IS ALWAYS IN THE FULL,
VERTICAL, LOCKED POSITION WHENEVER RESIDENT/PATIENT IS LEFT
UNATTENDED.
!
+($'
'(&.
(1'
POWERED AIR MATTRESS SURFACES
MAY POSE A RISK OF ENTRAPMENT.
PRIOR TO USE, ENSURE THE THERAPEUTIC BENEFITS OUTWEIGH THE
RISK OF ENTRAPMENT.
17
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
OPTIONAL PLASTIC HALF RAIL INSTALLATION & OPERATION
KIT ZA84200 - (Sample shows rail positioned on right side of bed)
RH Plastic Half Rail
Assembly (#2)
1. Position the Plastic Half Rail (#2) as shown, with the taller, straight edge
toward the head end of the bed and arms angled toward center of the bed.
2. From the outside, insert the two welded pins (with grooves) on the
rail arms into the two large holes in the side of the head deck.
3. From the inside, insert the metal hair pin clip end of the Lanyard
Assembly (#3) onto the exposed grooves at the end of the pins.
4. Position the other terminal end of the Lanyard
Assemblies (#3) over the small hole on the inside
of the deck frame. Secure with a small
threaded Phillips Screw (#4).
PLEASE ORDER PLASTIC RAIL KIT #ZA84200,
WHICH INCLUDES A RIGHT-HAND AND LEFTHAND HALF RAIL, FOUR LANYARD ASSEMBLIES,
AND 2 PHILLIPS SCREWS (OR 2 OPTIONAL HEX
HEAD SCREWS). ORDER BAG # 999-0842-905
FOR JUST THE REPLACEMENT HARDWARE.
Head Deck (#1)
TO
W
AR
OF D C
BE EN
D T
ER
Small
Hole
Lanyard
Assembly (#3)
Straight
Edge toward
Head End
Phillips
Screw (#4)
Lanyard
Assembly (#3)
THE PLASTIC RAIL CAN BE POSITIONED ON
EITHER THE HEAD OR FOOT DECKS FOR 80”
BEDS. THEY SHOULD ONLY BE PUT ON THE
HEAD END FOR 76” BEDS.
HEAD END
PLASTIC HALF RAIL OPERATION
SLEEP
SURFACE
!
TO AVOID PINCHING FINGERS, HOLD
THE HALF RAIL FROM THE TOP WITH
ONE HAND AND CAREFULLY DEPRESS
THE BLACK RELEASE LEVER WITH
THE OTHER. MAKE SURE THERE ARE
NO OBJECTS IN THE WAY THAT MAY
HINDER THE FULL MOVEMENT OF
THE RAIL.
GF Health Products, Inc. - www.grahamfield.com
SLEEP
SURFACE
!
FOR OPTIMUM SAFETY, PLEASE
MAKE SURE RAIL IS ALWAYS IN
ITS “FULL UP LOCKED” POSITION
WHEN LEAVING THE RESIDENT/
PATIENT UNATTENDED TO AVOID
POSSIBLE INJURY.
!
POWERED AIR MATTRESS SURFACES
MAY POSE A RISK OF ENTRAPMENT.
PRIOR TO USE, ENSURE THE THERAPEUTIC BENEFITS OUTWEIGH THE
RISK OF ENTRAPMENT.
18
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
OPTIONAL TRAPEZE SUPPORT INSTALLATION
(The Trapeze Support is attached to the head section of the bed.)
Please Order Kit Number ZA79000
Trapeze Support vertical
support tube. (TMI Bar
Sleeve would be inserted
inside the tube.)
+($'
(1'
0DLQ)UDPH
Use first holes in
Trapeze Support
to mount to main
frame tubes.
Use third hole
from the end of the
main frame tubes.
1. Begin by removing the headboard panel assembly (#2),
if previously assembled to the bed, by pulling out the
two Clevis Pins and two Hair Pin Clips that attach the
main frame tubes to the headboard’s mounting tubes.
Set all pins aside for later use.
2. Detach the headboard panel from the mounting tubes
by unscrewing the four 40mm Allen Head Bolts that
hold the board to the tubes (these will be replaced with
the longer Phillips Head Pan Screws from the trapeze
adaptor hardware bag). Do not remove the (4) four
1/4-20 inserts (#3) from the board. They will be used
again to mount the board to the trapeze support.
3. Assemble the Trapeze Support (#1) to the main frame
tubes using the two Clevis Pins and Hair Pin Clips you
removed in Step 1. The first holes in the Trapeze tubes
must line up with the third hole from the end in the
main frame tubes as shown.
GF Health Products, Inc. - www.grahamfield.com
USE SAME CLEVIS PINS AND HAIR PIN CLIPS
THAT
WERE USED TO CONNECT HEADBOARD
TO MOUNTING TUBES.
4. Insert the 1/4-20 x 2.50” Carriage Bolt (#5) into the vertical
support as shown and fasten with a 1/4-20 Hex Head Lock
Nut (#6). Both parts should be in the hardware bag.
5. Assemble the headboard to the inside of the Trapeze Support
so that the side of the headboard with the inserts is facing
away from the Trapeze Support. From the outside, insert
the (4) four 1/4-20 x 1.75” long Machine Screws (#4) from
the hardware bag through the holes in the Trapeze Support,
screwing them into the inserts in the headboard.
6. OPTIONAL - FOR TMI TRAPEZE BAR WITH SLEEVE:
Insert the Sleeve into the vertical support with the slot on
the bottom. Rotate the sleeve until it falls into place over
the carriage bolt you inserted in Step 4. This will lock it into
the proper position. (NOTE: The top of the Sleeve should
sit flush with the top of the vertical support on the Trapeze
Support Adaptor.)
19
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
SECTION C
Mechanical & Electrical
Information
GF Health Products, Inc. - www.grahamfield.com
20
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
ZENITH 9000 MECHANICS
ZENITH 9000 ELECTRICAL
NOTE: All dimensions are in a range of +/- .25 inches
• Overall Bed Length (with brds & wallsaver) . . 82”/86”
• Overall Bed Width (with boards) . . . . . . . . . . . 36.00”
• Maximum Height* . . . . . . . . . . . . . . . . . . . . . . 30.00”
• Minimum Height* . . . . . . . . . . . . . . . . . . . . . . . 7.00”
• Maximum Head/Back Deck Angle . . . . . . . . . . . . 70°
• Maximum Knee/Foot Deck Angle . . . . . . . . . . . . 30°
• Maximum Safe Working Load . . . . . . . . . . . 600 lbs.
WITH WEIGHT EVENLY DISTRIBUTED
- includes bedding, resident, support surface,
and all accessories.
• Power/Frequency . . . . . . . . . . . . 120 Volt/ 50/60 Hz
• Output Rating . . . . . . . . . . . . . . . . . . . . 12/33V IPX4
• Overall Movement Draw . . . . . . . . . . . . . 4.50 Amps
• Electrical Cord . . . . . . . . . . . . #18 AWG 3 Conductor
Type SJT
• Mode of Operations
. . . . . . . . .10% Max. Duty Cycle
2 minutes on/18 minutes off
• Internal Battery Backup
. . . . . . . . . . . . . . 9V Battery
Pack and Charger can be purchased separately as
an accessory.
• Mass of bed (without assist devices or boards) = 204 lbs.
* Bed height calculated from floor surface to top of
sleep deck.
TYPICAL ZENITH 9000 BED IDENTIFICATION LABELS
with Grounded Electrical Cable
MODEL NO
GF HEALTH
PRODUCTS, INC.
808-0000-000000
MFG. DATE
4/01/13
ATLANTA, GA 30360
VOLT HZ AMP TYPE
110-120 50/60 4.5
AC
DUTY CYCLE - 2 min Continuous/18 min
MODE OF OPERATION - Intermittent
!
= 600 lbs
SAFE WORKING LOAD
ZZ98174
IPX6
ZENITH 808 SERIES
PATENT PENDING
ZENITH 9000
MODEL NO. 808-0000-000000
SERIAL NO
000000000000
SERIAL ZZ9
MFG DATE 4/01/13
Bed labels are an important part of
identifying the bed’s make and model
when ordering replacement parts. The
Serial Number is essential if you are
claiming parts or service under warranty.
These helpful labels can be located on
the main frame rails, immediately below
the sleep decks on either side of the bed.
Please have this IMPORTANT information ready when calling our customer
service or technical support staff at
800-365-2338; it will allow us to better
assist you and quickly answer your
questions and concerns.
000000000000
ZZ98174
GF Health Products, Inc. - www.grahamfield.com
21
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
ZENITH 9000 SERIES ELECTRICAL COMPONENTS
Plug-in for
Optional
Battery
Backup
Control/Junction Box
Part # 999-0844-300A
Quantity = 1
Box and cable color = White
Pendant/Hand Controller
Part # 999-0808-305
Quantity = 1
Pendant & Alligator Clip
Part # 999-0808-112
(included with your bed)
To order a 3-prong detachable
power cable, please use Part
# 999-0844-208. Quantity = 1
Color = White
Head Motor/Actuator
Part # 999-0844-052SP
Quantity = 1
Color = White Casing
Foot Motor/Actuator
Part # 999-0844-053SP
Quantity = 1
Color = White Casing
HI/LO Motor/Actuator
Part # 999-0844-051SP
Quantity = 2
Color = White Casing
Phone Jack end
for Staff Control
Short Control Cable
Part # 999-0844-200SP
Quantity = 1
Color = Black
9 Pin Din Plug
for Control Box
White Single T-Cable
Part # 999-0844-201SP
Quantity = 1
Color = White
Unused Phone Jack Receptor
for Hand Pendant (with
screw-on protective cap)
Phone Jack Receptor
for Hand Pendant
Phone Jack Pug-in
for Control Box
Pendant Holster
Part # 999-0791-000
Quantity = 1
(included with your bed)
Clipped on Pendant
when bed first shipped.
!
DO NOT use unauthorized parts, accessories, or adaptors other than those specified/authorized by GF Health Products, Inc.
DO NOT open assemblies such as the Actuators, Hand Control, or Control Box. If unauthorized personnel perform work on
these components, the manufacturer’s warranty becomes void. NEVER operate the bed if a Power Cord or Plug is damaged
or not working properly. Contact qualified Service Personnel for examination and repair. Always unplug the Power Cord when
performing any maintenance on the bed.
GF Health Products, Inc. - www.grahamfield.com
22
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
u
ZENITH 9000 SERIES ELECTRICAL CABLING
POWER CABLE
T-CABLE
HEAD CABLE
FOOT CABLE
HI/LO CABLE (FOOT)
HI/LO CABLE (HEAD)
BLACK CONTROL CABLE
GROUND WIRE
I
Ground
Wire
x
III IIII
White HI/LO (Hd.) Cable
White HI/LO (Ft.) Cable
White Head Motor Cable
9V Battery
Compartment
u
v
Black Control Cable
Control Cable (crown)
Head - Port I
Foot - Port II
HI/LO (Ft) - Port III
HI/LO (Hd) - Port IIII
II
White Foot Motor Cable
u
v
w
x
y
z
{
|
Optional Battery
Backup Plug-in
Power Cable
Plug-in
NOTE: 9V Battery included in top of box is good
for one use only in event of a power outage. An
optional portable Ilcon Battery Backup unit is
recommended for longer periods where power is
not available. Contact your sales representative
for more information.
GF Health Products, Inc. - www.grahamfield.com
w
u
v
z
y
v
w
x
y
z
u|
{
v {
Control Cable plugged into
T-Cable for Shipping.
23
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
SECTION D
SERVICE/REPLACEMENT
PARTS
GF Health Products, Inc. - www.grahamfield.com
24
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
SERVICE/REPLACEMENT PART RECORD (Page 1)
DECKING
Part Number
Description
QTY
999-0844-920SP
Head/Back Deck & Hardware Pack
1 Deck
999-0844-930SP
OR - Foot Deck & Hardware Pack
1 Deck
999-0844-940SP
OR - Knee Deck & Hardware Pack
1 Deck
Deck Hardware Pack - INCLUDES . . .
1 Pkg
Separate
Hardware Pack
999-0844-990
4
Clevis Pins
5
5/16” Retaining Rings (Deck Brackets)
2
12mm Retaining Ring (Cntrl Arms to Decks)
1
Installation Instruction Sheet
Order Date
Price
Order Date
Price
Order Date
Price
Order Date
Price
MOTORS (ACTUATORS)
Part Number
Description
QTY
999-0844-051SP
HI/LO Motor (Cable attached) & Hardware Pack
1 Motor
999-0844-052SP
OR - Head Motor (Cable attached) & Hardware Pack
1 Motor
999-0844-053SP
OR - Foot Motor (Cable attached) & Hardware Pack
1 Motor
Motor Hardware Pack- INCLUDES . . .
1 Pkg
Separate
Hardware Pack
999-0844-991
2
12mm Retaining Rings
2
Hair Pin Clips
2
Snap Rings
8
Standard Cable Ties
1
Installation Instruction Sheet
CONTROL BOX & POWER CABLES
Part Number
Description
QTY
999-0844-300SP
Linak Control Box Service Pack (includes control cable)
1 Kit
Service Pack - INCLUDES . . .
Separate
Hardware Pack
999-0844-992
1
Adaptor Control Cable 999-0844-200
1
Ground Screw
8
Standard Cable Ties
1
Installation Instruction Sheet
999-0844-300A
Linak Control Box (includes 9V battery)
1 Box
999-0844-208
Detachable Ilcon 3-Prong Power Cable
1 Cable
PENDANT/HAND CONTROLLER
Part Number
Description
QTY
999-0808-305
Pendant/Hand Controller (Std. Model)
1 Pendant
999-0791-000
Pendant Holster (Std. for all pendants)
1 Holster
GF Health Products, Inc. - www.grahamfield.com
25
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
SERVICE/REPLACEMENT PART RECORD (Page 2)
SINGLE T-CABLE
Part Number
Description
QTY
999-0844-201SP
White Single “T” Control Cable
1 Pack
“T” Cable Hardware Pack - INCLUDES . . .
1 Pkg
Separate
Hardware Pack
999-0844-993
1
Split Stem Cable Retainer (Bumper)
2
Push Cable Ties
6
Standard Cable Ties
1
Installation Instruction Sheet
Order Date
Price
Order Date
Price
Order Date
Price
Order Date
Price
SHORT BLACK CONTROL CABLE
Part Number
Description
QTY
999-0844-200SP
Black Control Cable Kit
1 Pack
Control Cable Service Pack - INCLUDES . . .
1 Pkg
No Separate
Hardware Pack
2
Standard Cable Ties
1
Installation Instruction Sheet
STAFF CONTROL
Part Number
Description
QTY
999-0775-901
Switch Pad with Bezel & Cables
1 Unit
ZL788000
Staff Control Service Pack - INCLUDES . . .
1 Pkg
PLEASE SEE
PAGE 13
FOR
INSTALLATION
INSTRUCTIONS
1
Switch Pad with Bezel & Cables
1
Shroud (Cable Cover)
6
#6 Phillips Head Truss Screws
3
4” Nylon Cable Tie
1
Installation Instruction Sheet
CAPS & PLUGS
Part Number
Description
QTY
NOTE: CAPS & PLUGS CAN ONLY BE PURCHASED IN SETS OF 12
100-4200-004PK
1.25” x 1.25” Square Caps Pack
12/pkg
100-4700-015PK
1.00” x 1.00” Square Caps Pack (arm ends)
12/pkg
100-4700-017PK
1.00” x 2.00” Rectangular Caps Pack
12/pkg
100-4700-021PK
.75” x 1.50” Rectangular Caps Pack
12/pkg
100-4700-018PK
1.25” x 2.00” Rectangular Caps Pack
12/pkg
100-4715-011PK
1.50” Round End Caps Pack (cover arm bearings)
12/pkg
999-0775-001PK
Half Moon End Caps Pack (caster bases)
12/pkg
100-4762-002PK
5/8” Round Plugs Pack (both sides of foot deck)
12/pkg
100-4738-005PK
3/8” Round Plugs (on main frame rails - foot end)
12/pkg
FOR GENERAL CAP/PLUG DIAGRAMS PLEASE SEE PAGES 31 & 32
GF Health Products, Inc. - www.grahamfield.com
26
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
SERVICE/REPLACEMENT PART DIAGRAM - ELECTRONICS
END OF BLACK
CONTROL CABLE
(BLACK)
FOOT-END
OF T-CABLE
(WHITE)
CONTROL BOX
FOOT-END
HI/LO MOTOR
LONGER SIDE OF T-CABLE
WITH PUSH CABLE TIE IN
SMALL HOLE & CAP
HEAD-END
HI/LO MOTOR
FOOT
END
FOOT/KNEE
MOTOR
HEAD
MOTOR
LONG “T” OF T-CABLE
SECURED TO ROD
AND MAIN FRAME
BRACKET WITH
CABLE TIES
SHORTER SIDE OF T-CABLE WITH
PUSH CABLE TIE IN SMALL HOLE
HEAD
END
CABLE PROTECTION GROMMET
IN SEAT PAN KEY HOLE
POWER CABLE
PLUG AT HEAD END
POWER CABLE SECURED TO ROD
WITH CABLE TIES
1. TO ORDER A REPLACEMENT
HI/LO MOTOR USE SERVICE PACK
999-0844-051SP (Includes motor,
mounting hardware & installation
instruction sheet).
2. TO ORDER A REPLACEMENT
HEAD MOTOR USE SERVICE PACK
999-0844-052SP (Includes motor,
mounting hardware & installation
instruction sheet).
3. TO ORDER A REPLACEMENT
FOOT MOTOR USE SERVICE PACK
999-0844-053SP (Includes motor,
mounting hardware & installation
instruction sheet).
4. TO ORDER A REPLACEMENT
CONTROL BOX PLEASE USE
999-0844-300A (Includes control
box, detachable power cord, control
cable, ground wire screw, cable ties,
& installation instruction sheet).
5. TO ORDER A REPLACEMENT
SINGLE T-CABLE USE SERVICE
PACK 999-0844-201SP (Includes
T-Cable, cable ties, grommets &
installation instruction sheet).
6. TO ORDER A REPLACEMENT
CONTROL CABLE USE PART
999-0844-200SP. (Includes cable,
two (2) cable ties & installation
instruction sheet).
WHEN ORDERING REPLACEMENT PARTS WITH CUSTOMER SERVICE,
PLEASE HAVE THE BED SERIAL NUMBER AVAILABLE
TO CONFIRM WHETHER THE PART IS COVERED UNDER WARRANTY.
(SEE PAGE 21 FOR LOCATION OF SERIAL NUMBER ID LABEL.)
GF Health Products, Inc. - www.grahamfield.com
27
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
REPLACEMENT OF 9V BATTERY & OPTIONAL
BATTERY BACKUP CHARGER AND BATTERY PACK
REPLACING YOUR INTERNAL 9V BATTERY:
1. Remove battery cover on the underside of your
control box by unscrewing the two phillips screws
as shown.
2. Remove the existing battery connected to the
Connector Cable from the battery slot.
3. Unplug the existing battery and discard. Plug
in the new battery to the Connector Cable and
reinsert into slot. Replace battery cover.
NOTE: THE 9V BATTERY INCLUDED WITH YOUR CONTROL BOX IS ONLY GOOD FOR
ONE CHARGE - LOWERING THE BED ONCE IN THE EVENT OF A POWER OUTAGE. YOU
WILL NEED TO REPLACE AFTER EACH SINGLE USAGE. A STRONGER BATTERY PACK IS
AVAILABLE AS A SEPARATE PURCHASE. PLEASE ORDER WITH BACKUP CHARGER.
Battery Charger
Adaptor Cable
Plugs directly
into “optional”
ILCOCHARGE
Backup Battery
and Battery
Pack purchased
separately.
To plug in battery charger,
first remove the protective
cap with small screwdriver.
GF Health Products, Inc. - www.grahamfield.com
28
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
SECTION E
FRAMING SERVICE PARTS
For All Zenith 9000 Bed Models
GF Health Products, Inc. - www.grahamfield.com
29
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
SERVICE/REPLACEMENT PART DIAGRAM - DECKING
HEAD DECK
TO MAIN FRAME
SEAT PAN BRACKETS
Seat
Pan
Bracket
(or
second
Deck
Bracket)
DETAIL OF DECK
ATTACHMENT
(Similar for all decks)
KNEE DECK
TO MAIN FRAME
SEAT PAN BRACKETS
FOOT DECK
TO KNEE DECK
MOUNTING BRACKETS
DETAIL OF EDEMA
RATCHET RE-ATTACHMENT
(Use existing ratchets
and hardware)
1. TO ORDER A REPLACEMENT
HEAD DECK USE SERVICE PACK
999-0844-920SP (includes deck,
mounting hardware & installation
instruction sheet).
2. TO ORDER A REPLACEMENT
KNEE DECK USE SERVICE PACK
999-0844-940SP (includes deck,
mounting hardware & installation
instruction sheet).
3. TO ORDER A REPLACEMENT
FOOT DECK USE SERVICE PACK
999-0844-930SP (includes all deck,
mounting hardware & installation
instruction sheet). Re-use existing
edema ratchets & ratchet hardware.
WHEN ORDERING REPLACEMENT PARTS WITH CUSTOMER SERVICE,
PLEASE HAVE THE BED SERIAL NUMBER AVAILABLE
TO CONFIRM WHETHER THE PART IS COVERED UNDER WARRANTY.
(SEE PAGE 21 FOR LOCATION OF SERIAL NUMBER ID LABEL.)
GF Health Products, Inc. - www.grahamfield.com
30
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
SERVICE/REPLACEMENT PART DIAGRAM MAIN FRAME CAPPING
HEAD
END
FOOT
END
CAPS OR PLUGS ARE NOT COVERED UNDER WARRANTY
(PACKS OF 12 CAN BE ORDERED IN THE EVENT YOU DAMAGE OR LOSE
ANY CAPS/PLUGS ON THE BED - SEE BOTTOM OF PAGE 26 FOR ORDER NUMBERS)
GF Health Products, Inc. - www.grahamfield.com
31
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
SERVICE/REPLACEMENT PART DIAGRAM CAPPING ON HEAD, KNEE, AND FOOT DECKS
CAPPING ON ARMS & LEGS
2X 100-4700-018
End Caps
2X 100-4700-018
Rectangular End Caps
4X 100-4715-011
Round End Caps
2X 100-4700-021
Rectangular End Caps
CAPS OR PLUGS ARE NOT COVERED UNDER WARRANTY
(PACKS OF 12 CAN BE ORDERED IN THE EVENT YOU DAMAGE OR LOSE
ANY CAPS/PLUGS ON THE BED - SEE BOTTOM OF PAGE 26 FOR ORDER NUMBERS)
GF Health Products, Inc. - www.grahamfield.com
32
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
SECTION E
TROUBLESHOOTING
All ZENITH 9000 Models
GF Health Products, Inc. - www.grahamfield.com
33
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
ZENITH 9000 ELECTRONIC TROUBLESHOOTING
QUICK REFERENCE
The Zenith 9000 Series beds use a 4-motor system with ILCON electronics.
NO POWER
1. Check Outlet.
2. Unplug Power Cord and Check following . . .
a. Check Power Cord for damage or pinching.
b. Check short black, Control Box Cable for damage or pinching.
c. If any cables are damaged, replace immediately.
PENDANT NOT WORKING (BUT STAFF CONTROL WORKS)
1. Are functions locked out on Staff Control?
2. Check all Pendant and T-Cable connections.
3. Unplug Power Cord.
4. Unplug Hand Pendant from T-Cable.
5. Plug Hand Pendant directly into short, black Control Box Cable and test.
a. If Pendant works, replace T-Cable.
b. If Pendant does not work, unplug from short, black Control Cable;
unplug short, black Control Cable from Control Box; replug Pendant
directly into the Control Box. Replug Power Cord and test.
c. If Pendant works from the Control Box, replace the Control Cable.
(Please refer to page 26 in this Service Manual for replacement part #.)
STAFF CONTROL NOT WORKING (LIGHTS BLINKING)
1. Check all Staff Control connections.
2. Unplug Power Cord.
3. Unplug Staff Control Cable from short, black Control Box Cable.
4. Unplug Hand Pendant from T-Cable.
5. Plug Hand Pendant directly into short, black Control Box Cable and test.
a. If Pendant works, replace Staff Control Assembly. (Please refer to
page 26 in this Service Manual for replacment part #.)
b. If Pendant does not work, unplug from short, black Control Cable;
unplug short, black Control Cable from Control Box; and replug
the Pendant directly into the Control Box and test.
c. If Pendant works from the Control Box, replace the short, black
Control Box Cable. (Please refer to Page 26 in this Service Manual
for replacment part #.)
!
HEAD
PENDANT LOCK
LOCKOUT LIGHT
HILO
PENDANT LOCK
LOCKOUT LIGHT
FOOT
PEND LOCK
LOCK LIGHT
HEAD HEAD HOLD HI/LO HI/LO FOOT FOOT
UP DOWN
UP DOWN
UP DOWN
ALWAYS UNPLUG THE POWER CORD BEFORE DOING ANY ELECTRICAL WORK
ON THE BED. IF 3-PRONG POWER CORD IS DAMAGED, REPLACE IMMEDIATELY!
GF Health Products, Inc. - www.grahamfield.com
34
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
ZENITH 9000 ELECTRONIC TROUBLESHOOTING
QUICK REFERENCE
HEAD OR FOOT MOTOR MALFUNCTIONING
(DECK DOES NOT GO UP AND/OR DOWN)
1. Check All Motor Cable Connections.
2. Check Motor Condition - Cracked Housing, Scratches, Bent Shaft, etc.
3. Is Function Locked Out on Staff Control?
4. HI/LO & Foot Works, But Head Does Not . . .
a. Unplug Power Cord.
b. Remove Cord Guard at Control Box.
c. Switch Head & Foot Motor Cables at the Control Box.
d. Replug Power Cord and Test.
5. HI/LO & Head Works, But Foot Does Not . . .
a. Unplug Power Cord.
b. Remove Cord Guard at Control Box.
c. Switch Foot & Head Motor Cables at the Control Box.
d. Replug Power Cord and Test.
6. Motor Grinding Loudly - Replace Motor.
HI/LO MOTOR MALFUNCTIONING
(ENTIRE BED DOES NOT GO UP AND/OR DOWN)
1. Check All Motor Cable Connections.
2. Check Motor Condition - Cracked Housing, Scratches, Bent Shaft, etc.
3. Is Function Locked Out on Staff Control?
4. Head & Foot Motor Works, But HI/LO Does Not . . .
a. Unplug Power Cord
b. Remove Cord Guard at Control Box
c. Switch HI/LO Cables at the Control Box
d. Replug Power Cord and Test
5. HI/LO Motors Need to be Re-aligned (Power Surge, Outage,
or Replacement) . . .
a. Unplug Power Cord.
b. Remove Cord Guard at Control Box.
c. Unplug short, black Control Cable from Control Box
(leave staff control attached).
d. Unplug Pendant from T-Cable.
e. Plug Pendant directly into Control Box Port.
f. Replug Power Cord.
g. Press the HI/LO Down button until the bed is all the way down
(may take a number of attempts).
h. Once down, press and hold the Down HI/LO button for 15-20 seconds.
i. Test Up and Down Functions (repeat steps g & h if necessary).
j. Unplug Power Plug and replug Pendant into T-Cable and
Control Cable into Control Box.
k. Replug Power Cord and test.
GF Health Products, Inc. - www.grahamfield.com
HI/LO (Hd.)
HI/LO (Ft.)
Foot
Head
Control
Cable
35
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
TROUBLESHOOTING/REPLACING THE STAFF CONTROL
1. REMOVING AND REPLACING THE
STAFF CONTROL ASSEMBLY
6WDII&RQWURO
$VVHPEO\
a. UNPLUG THE POWER CORD FROM
THE WALL OUTLET.
b. Unscrew the four Phillips Screws (#1) that attach the
Shroud (cable cover) to the footboard and set aside.
c. At the foot end of the bed, unscrew the retaining
cap on the T-Cable (#3) and unplug the two cables.
6WDII&RQWURO
%HYHO
6FUHZV
)RRW%RDUG
ZLWKFXWRXW
d. Unscrew the two remaining Phillips Screws (#2)
from the inside of the footboard that attach the
Staff Control Assembly bevel to the board. Set
aside screws for later re-assembly.
6WDII&RQWURO
%HYHO6FUHZV
e. Remove the OLD Staff Control Assembly and feed
the old cable out through the large hole.
6KURXG6FUHZV
f. Feed the cable of the NEW Staff Control
Assembly from the outside through the
large hole and insert the bevel into the
cutout on the outside of the footboard.
g. Secure the Staff Control by
re-inserting the two Phillips
Screws (#2) you removed
in Step (d).
IMPORTANT:
Run a Cable
,03257$175XQD&DEOH
Tie
through the end hole in
7LHWKURXJKWKHHQGKROHLQ
the
mounting tube, loop the
WKHPRXQWLQJWXEHORRSWKH
excess
cable, run the tie
H[FHVVFDEOHUXQWKHWLH
around
cable, and pull tight
DURXQGFDEOHDQGSXOOWLJKW
to
secure. Cut off excess
WRVHFXUH&XWRIIH[FHVV
cable
tie.
FDEOHWLH
h. Re-position the Shroud on
the inside of the footboard
and secure with the four
Phillips Screws (#1) you
removed in Step (b).
i. Plug the T-Cable (#5) into the Staff Control
Cable (#4), making sure the phone jack plug
is seated correctly into the Staff Control cable plug.
Screw on the retaining cap (#3) to secure.
IMPORTANT:
j. Run a Cable Tie through the large end hole on
the right-hand footboard mounting tube.
k. Loop the excess Staff Control Cable. Run the cable
tie around the cable and pull tight to secure. Cut off
any excess Cable Tie.
GF Health Products, Inc. - www.grahamfield.com
)HPDOHHQG
RI6WDII&RQWURO
&DEOH
End
of single T-Cable
(QGRI'RXEOH7&DEOH
DWIRRWHQG*UH\
at
foot end - White
7UXQVRQHLWKHU
(“T”
runs on either
VLGHRI6HDW3DQ
side
of Seat Pan
IRUDWWDFKLQJ\RXU
for
attaching the
+DQG&RQWUROOHU
Hand Controller.)
/RFNLQJ
(QG&DS
36
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
NOTES:
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
GF Health Products, Inc. - www.grahamfield.com
37
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
NOTES:
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
GF Health Products, Inc. - www.grahamfield.com
38
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
ZENITH SERIES
LONG TERM CARE BEDS LIMITED WARRANTY
Products manufactured by Basic American Medical Products are warranted to the original purchaser
to be free of defects in material and workmanship for the warranty period listed below commencing from
the date of shipment.
Zenith9000
APS*
Zenith9000*
Zenith7000*
Zenith5000*
Matrix II
Liberty
Eze-Lok
Flex
Bariatric
Frame
15 years
15 years
15 years
15 years
15 years
15 years
15 years
Motors and
Control Box
5 years
5 years
3 years
3 years
n/a
n/a
2 years
Non-specified
electronics
3 years
3 years
3 years
3 years
n/a
n/a
2 years
Bed mounted
accessories
and unspecified
components
2 years
2 years
2 years
2 years
2 years
2 years
2 years
Headboards and
Footboards
1 year
1 year
1 year
1 year
1 year
1 year
1 year
February 2013
* includes all 230V and Slide-Wide bed models
■ This warranty does not apply to damage resulting from abuse, accident, negligence, misuse,
unsuitable environmental conditions, improper cleaning, or caused by unauthorized alteration,
repair, maintenance, assembly, or installation.
■ The beds should be used only for their intended purpose and maintained according to the
service manual provided with the bed.
■ Basic American’s liability shall not exceed the original purchase price.
■ Any repair work or replacement shall not exceed the warranty duration.
■ Basic American Medical Products will, at its option, repair or replace defective product or
parts, provided that the replacement or return has been previously authorized by Basic
American or one of its divisions under the terms of this warranty.
If you have questions regarding a bed’s warranty, please contact
Basic American Medical Products at 1-800-365-2338.
GF Health Products, Inc. - www.grahamfield.com
39
Zenith 9000 Service Manual 999-0844-190D - DEC. 2013
336 Trowbridge Dr. • Fond du Lac, WI 54937
Customer Service: 1.800.365.2338 • Fax: 920.929.8213
www.grahamfield.com
© 2013 GF Health Products, Inc.
All Rights Reserved
Basic American Medical Products and Zenith
are registered trademarks of GF Health Products, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement