Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Correction 1
2009-08-11
Page 1 of 1
Report Reference #
E209323-A50-CB-1
COVER PAGE FOR TEST REPORT
Test Item Description:
Model/Type Reference:
Rating(s):
Server
745-8, 745-12
Model 745-8: 100-240 V, 60-50 Hz., 10-4 A
Model 745-12: 100-240 V, 60-50 Hz., 11.5-5.5 A
Standards:
IEC 60950-1:2001, First Edition
Applicant Name and
SUPER MICRO COMPUTER INC
Address:
980 ROCK AVE
SAN JOSE CA 95131
UNITED STATES
Factory Location(s):
SUPER MICRO COMPUTER INC
980 ROCK AVE
SAN JOSE CA 95131
UNITED STATES
This Report includes the following parts, in addition to this cover page:
1. Specific Technical Criteria
2. Critical Components
The original report was modified on 2009-08-11 to include the following changes/additions:
1. Corrected the rating from 11-5.5 A to 11.5-5.5 A to Model 745-12 to Cover Page
2. Corrected the rating Input from 11-7.5 A to 11.5-8 A; DC output from 12 V/74 A to 12 V/83 A, from 900 W
to 1000 W, and Input from 8-5 A to 8-5.5 A for 1200 W to alternate Power Supply, (Type PWS-1K21P-1R by
Compuware Technology Inc.) to Critical Component List.
All applicable tests according to the above standard(s) have been carried out.
Test results are valid only for the tested equipment.
This Test Report can be reproduced only in whole.
Amendments and corrections can be reproduced only with the original CB Test Report.
Written permission from Underwriters Laboratories Inc. is required if the test report is copied in part.
Copyright © 2002Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Correction 1
2009-08-11
Page 1 of 11
Report Reference #
E209323-A50-CB-1
Test Report issued under
the responsibility of:
Underwriters Laboratories Inc.
TEST REPORT
IEC 60950-1,First Edition
Information technology equipment-Safety
Part 1:General Requirements
Report Reference No .................. :
E209323-A50-CB-1
Date of issue ................................. :
2009-06-16
Total number of pages .................. :
11
CB Testing Laboratory ............... :
Underwriters Laboratories Inc.
Address ......................................... :
455 E. Trimble Rd., San Jose, CA, 95131-1230, USA
Applicant's name ........................ :
SUPER MICRO COMPUTER INC
980 ROCK AVE
SAN JOSE CA 95131
UNITED STATES
Address ......................................... :
Test specification:
Standard ....................................... :
IEC 60950-1:2001, First Edition
Test procedure .............................. :
CB Scheme
Non-standard test method ............ :
N/A
Test Report Form No. ................. :
IEC60950_1B
Test Report Form originator .......... :
SGS Fimko Ltd
Master TRF ................................... :
dated 2003-03
Copyright © 2005 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is
acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not
assume liability for damages resulting from the reader's interpretation of the reproduced material due to its
placement and context.
If this test Report is used by non-IECEE members, the IECEE/IEC logo shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Correction 1
2009-08-11
Test item description .................. :
Page 2 of 11
Report Reference #
Server
Trade Mark .................................... :
Model/Type reference ................... :
745-8, 745-12
Manufacturer ................................. :
SUPER MICRO COMPUTER INC
980 ROCK AVE
SAN JOSE CA 95131
UNITED STATES
Rating ............................................ :
Model 745-8: 100-240 V, 60-50 Hz., 10-4 A
Model 745-12: 100-240 V, 60-50 Hz., 11.5-5.5 A
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Correction 1
2009-08-11
Page 3 of 11
Report Reference #
E209323-A50-CB-1
Testing procedure and testing location:
[x]
CB Testing Laboratory
Testing location / address.............. :
[ ]
Underwriters Laboratories Inc. 455 E. Trimble Rd., San Jose,
CA, 95131-1230, USA
Associated CB Test Laboratory
Testing location / address.............. :
[ ]
Tested by (name + signature) ....... :
Greg Gatt
Approved by (+ signature) ............. :
Kevin F. Tang
Testing Procedure: TMP
Tested by (name + signature) ....... :
Approved by (+ signature) ............. :
Testing location / address.............. :
[ ]
Testing Procedure: WMT
Tested by (name + signature) ....... :
Witnessed by (+ signature)............ :
Approved by (+ signature) ............. :
Testing location / address.............. :
[ ]
Testing Procedure: SMT
Tested by (name + signature) ....... :
Approved by (+ signature) ............. :
Supervised by (+ signature) .......... :
Testing location / address.............. :
[ ]
Testing Procedure: RMT
Tested by (name + signature) ....... :
Approved by (+ signature) ............. :
Supervised by (+ signature) .......... :
Testing location / address.............. :
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Correction 1
2009-08-11
Page 4 of 11
Report Reference #
E209323-A50-CB-1
Summary of Testing:
No tests were conducted
Summary of Compliance with National Differences:
AR, AT, AU, BE, CA, CH, CN, CZ, DE, DK, ES, EU, FI, FR, GB, GR, HU, IE, IL, IN, IT, JP, KE, KR,
MY, NL, NO, NZ, PL, PT, SE, SG, SI, SK, US
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Correction 1
2009-08-11
Page 5 of 11
Report Reference #
Copy of Marking Plate
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Correction 1
2009-08-11
Page 6 of 11
Report Reference #
E209323-A50-CB-1
Test item particulars :
Equipment mobility .............................................. :
movable
Operating condition ............................................. :
continuous
Mains supply tolerance (%) ................................. :
+10%, -10%
Tested for IT power systems ............................... :
Yes
IT testing, phase-phase voltage (V) .................... :
230 V
Class of equipment ............................................. :
Class I (earthed)
Mass of equipment (kg) ....................................... :
26.0 kg.
Protection against ingress of water ..................... :
IP X0
Possible test case verdicts:
- test case does not apply to the test object ........ :
N/A
- test object does meet the requirement ............. :
P(Pass)
- test object does not meet the requirement ....... :
F(Fail)
Testing:
Date(s) of receipt of test item .............................. :
N/A
Date(s) of Performance of tests .......................... :
N/A
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a point is used as the decimal separator.
Refer to the Cover Page For Test Report for a list of all Factory Locations.
GENERAL PRODUCT INFORMATION:
Report Summary
The original report was modified on 2009-08-11 to include the following changes/additions:
1. Corrected the rating from 11-5.5 A to 11.5-5.5 A to Model 745-12 to Cover Page
2. Corrected the rating Input from 11-7.5 A to 11.5-8 A; DC output from 12 V/74 A to 12 V/83 A, from 900 W
to 1000 W, and Input from 8-5 A to 8-5.5 A for 1200 W to alternate Power Supply, (Type PWS-1K21P-1R by
Compuware Technology Inc.) to Critical Component List.
Product Description
The equipment is a tower type server in a metal chassis. All primary, AC circuits are contained within the
separate enclosure of the separately certified power supplies. The equipment has no connection to TNV
networks. The inside of the equipment is for access by trained service persons only. The equipment can
operate on one power supply; the second power supply is redundant. Each AC Input is for connection to a
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Correction 1
2009-08-11
Page 7 of 11
Report Reference #
E209323-A50-CB-1
separate branch circuit. The electrical ratings are per each AC Inlet.
Model Differences
All models are similar except for the alternate power supplies and alternate motherboards described in this
report, and minor cosmetic differences and/or differences in software, and/or minor differences in SELV logic
circuits.
Additional Information
Some of the attached component Licenses are greater than 3 years old, an accepting NCB may request
updated Licenses for these components.
The CB Certificates for the Power Supplies are provided as an attachment in this Report; the manufacturer
will provide the complete CB Report upon request from the accepting NCB.
Technical Considerations
The product was submitted and evaluated for use at the maximum ambient temperature (Tma) permitted by
the manufacturer’s specification of: 40 °C
The means of connection to the mains supply is: Pluggable A
The product is intended for use on the following power systems: TN, IT (Norway)
The equipment disconnect device is considered to be: Appliance Inlet
The class of laser product is: Incorporates previously certified Class 1 laser source (CD/DVD drive)
The product was investigated to the following additional standards: EN 60950-1:2001 + A11:2004 (which
includes all European national differences, including those specified in this test report).
The following circuit locations (with circuit/schematic designation) were investigated as a limited power
source (LPS): All external I/O connectors
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Correction 1
2009-08-11
Page 8 of 11
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
1.5.1
TABLE: list of critical components
object/part No.
Chassis /
Enclosure
(mech/elec/fire)
manufacturer/
trademark
-
Result - Remark
Pass
type/model
technical data
standard
-
Metal, minimum
thickness,
0.8mm. (overall
dimensions
550mm by
435mm by
178mm)
Min. 80ºC, for
application to
metal.
Input:
100-240V
50-60Hz,
10-4A.
dc Outputs:
+12V/66A;
+5V/18A
+5Vsb/4A
Input:
100-140V
11.5-8A
50-60Hz.
dc Outputs:
+12V/83A
+5Vsb/4A
1000W;
Input:
180-240V
8-5.5A
50-60Hz,
dc Outputs:
+12V/100A
+5Vsb/4A
1200W
12Vdc,
0.58A
(68.2CFM)
-
mark(s) of
conformity1)
-, -
UL969
UL, -
UL60950-1
IEC60950-1
EN60950-1
UL, TUV
UL60950-1
IEC60950-1
EN60950-1
UL, TUV
UL508
EN 60950-1
UL, VDE
UL508
EN 60950-1
UL, TUV
Nameplate Label BRADLEY
material
NAMEPLATE
CORP
Power Supply
ABLECOM
TECHNOLOGY
INC
White Thermal
Mylar
Power Supply,
alternate
COMPUWARE
TECHNOLOGY
INC
PWS-1K21P-1R
Rear External
Ventilation
Fans, two
provided.
Rear External
Ventilation
Fans, alternate,
two provided.
External Rear
Fan Guard /
SANYO DENKI
CO LTD
SAN ACE 80,
Model
9G0812P1F09
SANYO DENKI
CO LTD
9G0812P1F03
12Vdc,
0.58A
(68.2CFM)
CHI MEI CORP
PA-765B
V-0, minimum
UL94
2.5mm thickness UL60950-1
TRF No.: IEC60950__1B
Verdict
PWS-801-1R
Underwriters Laboratories Inc.
UL, -
Issue Date:
2009-06-16
Correction 1
2009-08-11
Page 9 of 11
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Frame
Assembly, two
provided
Mid-Chassis
Ventilation
Fans, optional,
up to three
provided
Mid-Chassis
Ventilation
Fans, optional,
alternate, up to
three provided
CPU fan
(optional)
Motherboard,
Super Micro
Computer, Model
X8 or H8 series
PTC
Thermistors, for
VGA, Mouse,
Keyboard, and
USB ports.
Note: PTC circuit
designations
may vary
between
motherboards
within the series,
however
protection
circuits are the
same.
PTC
Thermistors,
alternate, for
VGA, Mouse,
Keyboard, and
USB ports.
Note: PTC circuit
designations
may vary
between
motherboards
within the series,
however
Result - Remark
Verdict
SANYO DENKI
CO LTD
SAN ACE 80,
Model
9G0812P1F09
12Vdc,
0.58A
(68.2CFM)
UL508
EN 60950-1
UL, VDE
SANYO DENKI
CO LTD
9G0812P1F03
12Vdc,
0.58A
(68.2CFM)
UL508
EN 60950-1
UL, TUV
NIDEC
AMERICA
CORP
various
T92T12MHA7
UL508
EN 60950-1
UL, TUV
various
12Vdc
0.14A
(39.9CFM)
Min V-1;
Min.105 ºC
UL60950-1
IEC60950-1
UL, -
BOURNS INC
MF-MSMF150
6Vdc,
3A trip current.
EN60730-1
UL, TUV
TYCO
ELECTRONICS
CORP
miniSMDC150
6Vdc, 3A trip
current.
EN60730-1
UL, TUV
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Correction 1
2009-08-11
Page 10 of 11
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
protection
circuits are the
same.
Lithium Battery
Protection Circuit
Note: Resistor
and diode circuit
designations
may vary
between
motherboards
within the series,
however
protection
circuits are the
same.
Lithium Battery
SONY ENERGY CR2032
DEVICES CORP
Lithium Battery,
alternate
Lithium Battery,
alternate
Lithium Battery,
alternate
Lithium Battery,
alternate
Lithium Battery,
alternate
Printed Circuit
Boards (SELV)
Hard Disk Drive,
optional, one to
eight provided
Front Bezel for
Hard Disk Drives
CD/DVD Drive,
optional, up to
two provided.
VARTA
CR2032
MICROBATTER
Y
PANASONIC
CR2032
CORPORATION
,
PANASONIC*C
ORPORATION
OF NORTH
AMERICA
HITACHI
CR2032
MAXELL LTD
MITSUBISHI
ELECTRIC
CORP
FDK ENERGY
CO LTD
CR2032
various
various
SEAGATE
TECHNOLOGY
LLC
various
9CA154-302,
Barracuda ES2
CR2032
various
PANASONIC
UJDA710
CORPORATION
, PANASONIC
TRF No.: IEC60950__1B
Verdict
Resistor,
1kOhm, and
Diode in series.
-
-, -
3 V, maximum
10mA reverse
current.
3 V, maximum
5mA reverse
current.
3 V, maximum
5mA reverse
current.
UL1642,
IEC60950-1
UL, -
UL1642,
IEC60950-1
UL, -
UL1642,
IEC60950-1
UL, -
3 V, maximum
10mA reverse
current.
3 V, maximum
10mA reverse
current.
3 V, maximum
10mA reverse
current.
Min V-1;
Min.105 ºC
5Vdc/0.65A12Vd
c/0.42A
UL1642,
IEC60950-1
UL, -
UL1642,
IEC60950-1
UL, -
UL1642,
IEC60950-1
UL, -
UL796
UL, -
UL60950-1
IEC60950-1
UL, TUV
Min. HB,
Min. 80 C.
5Vdc/1.8A
Class 1 Laser
Product
UL94
UL60950-1
UL60950-1
EN60950-1
EN60825-1
UL, -
Underwriters Laboratories Inc.
UL, TUV,
Issue Date:
2009-06-16
Correction 1
2009-08-11
Page 11 of 11
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Floppy Disk
Drive, optional
CPU Air Guide,
Empty Disk Drive
Tray, Internal
Card Brackets,
Cover for Power
Supply Output
Board
Empty Disk Drive
Tray
Front Bezels for
Disk Drive Trays,
Front Disk Drive
Door, Plastic
Mesh/Frame
behind front disk
drive door, Top
Panel
Feet, Bottom of
Chassis, Four
Provided
Result - Remark
CORPORATION
OF NORTH
AMERICA
TEAC CORP
FD-05XYYY
Verdict
5V, 0.8A max.
UL60950-1
UL, -
various
various
Min. V-2,
Min. 80 C.
UL94
UL60950-1
UL, -
various
various
various
UL94
UL60950-1
UL94
UL60950-1
UL, -
various
Min. V-2,
Min. 80 C.
Min. HB,
Min. 80 C.
various
various
5VB, secured by
snap fit and
screw to chassis
bottom.
VTM-0, 80 C,
minimum
thickness
0.2mm, covers
bottom openings
in chassis.
VTM-0, 80 C,
minimum
thickness
0.254mm, covers
bottom openings
in chassis.
UL94
UL60950-1
UL, -
Barrier Sheet,
located on
chassis bottom,
covering bottom
openings.
SABIC
FR65
INNOVATIVE
PLASTICS US L
L C (E61257)
Barrier Sheet,
alternate, located
on chassis
bottom, covering
bottom
openings.
SABIC
FR700
INNOVATIVE
PLASTICS US L
L C (E61257)
1
UL94, UL60950- UL, 1
UL94, UL60950- UL, 1
) an asterisk indicates a mark which assures the agreed level of surveillance
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
UL, -
Issue Date:
2009-06-16
Page 1 of 1
Report Reference #
E209323-A50-CB-1
COVER PAGE FOR TEST REPORT
Test Item Description:
Model/Type Reference:
Rating(s):
Server
745-8, 745-12
Model 745-8: 100-240 V, 60-50 Hz., 10-4 A
Model 745-12: 100-240 V, 60-50 Hz., 11-5.5 A
Standards:
IEC 60950-1:2001, First Edition
Applicant Name and
SUPER MICRO COMPUTER INC
Address:
980 ROCK AVE
SAN JOSE CA 95131
UNITED STATES
Factory Location(s):
SUPER MICRO COMPUTER INC
980 ROCK AVE
SAN JOSE CA 95131
UNITED STATES
This Report includes the following parts, in addition to this cover page:
1. Specific Technical Criteria
2. Clause Verdicts
3. Critical Components
4. Test Results
5. Enclosures
a. National Differences
b. Photographs
c. Manuals
d. Miscellaneous
e. Licenses
All applicable tests according to the above standard(s) have been carried out.
Test results are valid only for the tested equipment.
This Test Report can be reproduced only in whole.
Amendments and corrections can be reproduced only with the original CB Test Report.
Written permission from Underwriters Laboratories Inc. is required if the test report is copied in part.
Copyright © 2002Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 1 of 48
Report Reference #
E209323-A50-CB-1
Test Report issued under
the responsibility of:
Underwriters Laboratories Inc.
TEST REPORT
IEC 60950-1,First Edition
Information technology equipment-Safety
Part 1:General Requirements
Report Reference No .................. :
E209323-A50-CB-1
Date of issue ................................. :
2009-06-16
Total number of pages .................. :
48
CB Testing Laboratory ............... :
Underwriters Laboratories Inc.
Address ......................................... :
455 E. Trimble Rd., San Jose, CA, 95131-1230, USA
Applicant's name ........................ :
SUPER MICRO COMPUTER INC
980 ROCK AVE
SAN JOSE CA 95131
UNITED STATES
Address ......................................... :
Test specification:
Standard ....................................... :
IEC 60950-1:2001, First Edition
Test procedure .............................. :
CB Scheme
Non-standard test method ............ :
N/A
Test Report Form No. ................. :
IEC60950_1B
Test Report Form originator .......... :
SGS Fimko Ltd
Master TRF ................................... :
dated 2003-03
Copyright © 2005 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is
acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not
assume liability for damages resulting from the reader's interpretation of the reproduced material due to its
placement and context.
If this test Report is used by non-IECEE members, the IECEE/IEC logo shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Test item description .................. :
Page 2 of 48
Report Reference #
Server
Trade Mark .................................... :
Model/Type reference ................... :
745-8, 745-12
Manufacturer ................................. :
SUPER MICRO COMPUTER INC
980 ROCK AVE
SAN JOSE CA 95131
UNITED STATES
Rating ............................................ :
Model 745-8: 100-240 V, 60-50 Hz., 10-4 A
Model 745-12: 100-240 V, 60-50 Hz., 11-5.5 A
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 3 of 48
Report Reference #
E209323-A50-CB-1
Testing procedure and testing location:
[x]
CB Testing Laboratory
Testing location / address.............. :
[ ]
Underwriters Laboratories Inc. 455 E. Trimble Rd., San Jose,
CA, 95131-1230, USA
Associated CB Test Laboratory
Testing location / address.............. :
[ ]
Tested by (name + signature) ....... :
Jerry Dikun
Approved by (+ signature) ............. :
Kevin Tang
Testing Procedure: TMP
Tested by (name + signature) ....... :
Approved by (+ signature) ............. :
Testing location / address.............. :
[ ]
Testing Procedure: WMT
Tested by (name + signature) ....... :
Witnessed by (+ signature)............ :
Approved by (+ signature) ............. :
Testing location / address.............. :
[ ]
Testing Procedure: SMT
Tested by (name + signature) ....... :
Approved by (+ signature) ............. :
Supervised by (+ signature) .......... :
Testing location / address.............. :
[ ]
Testing Procedure: RMT
Tested by (name + signature) ....... :
Approved by (+ signature) ............. :
Supervised by (+ signature) .......... :
Testing location / address.............. :
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 4 of 48
Report Reference #
E209323-A50-CB-1
Summary of Testing:
Unless otherwise indicated, all tests were conducted at Underwriters Laboratories Inc. 455 E. Trimble Rd.,
San Jose, CA, 95131-1230, USA.
Tests performed (name of test and test clause)
Testing location / Comments
End Product Reference Page
Input: Single-Phase (1.6.2)
Durability of Marking (1.7.13)
Limited Power Source Measurements (2.5)
Stability (4.1)
Connector Current Interruption (4.3.5)
Heating (4.5.1, 1.4.12, 1.4.13)
Electric Strength (5.2.2)
Abnormal Operation (5.3.1 - 5.3.8.2)
125 mm Flame Test/20 mm Flame (Annex A.1, A.2)
Summary of Compliance with National Differences:
AR, AT, AU, BE, CA, CH, CN, CZ, DE, DK, ES, EU, FI, FR, GB, GR, HU, IE, IL, IN, IT, JP, KE, KR,
MY, NL, NO, NZ, PL, PT, SE, SG, SI, SK, US
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 5 of 48
Report Reference #
Copy of Marking Plate
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 6 of 48
Report Reference #
E209323-A50-CB-1
Test item particulars :
Equipment mobility .............................................. :
movable
Operating condition ............................................. :
continuous
Mains supply tolerance (%) ................................. :
+10%, -10%
Tested for IT power systems ............................... :
Yes
IT testing, phase-phase voltage (V) .................... :
230 V
Class of equipment ............................................. :
Class I (earthed)
Mass of equipment (kg) ....................................... :
26.0 kg.
Protection against ingress of water ..................... :
IP X0
Possible test case verdicts:
- test case does not apply to the test object ........ :
N/A
- test object does meet the requirement ............. :
P(Pass)
- test object does not meet the requirement ....... :
F(Fail)
Testing:
Date(s) of receipt of test item .............................. :
2009-04-10
Date(s) of Performance of tests .......................... :
2009-04-24, 2009-04-28, 2009-04-29, 2009-04-30,
2009-05-04, 2009-05-05, 2007-02-26
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a point is used as the decimal separator.
Refer to the Cover Page For Test Report for a list of all Factory Locations.
GENERAL PRODUCT INFORMATION:
Report Summary
All applicable tests according to the referenced standard(s) have been carried out.
Product Description
The equipment is a tower type server in a metal chassis. All primary, AC circuits are contained within the
separate enclosure of the separately certified power supplies. The equipment has no connection to TNV
networks. The inside of the equipment is for access by trained service persons only. The equipment can
operate on one power supply; the second power supply is redundant. Each AC Input is for connection to a
separate branch circuit. The electrical ratings are per each AC Inlet.
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 7 of 48
Report Reference #
E209323-A50-CB-1
Model Differences
All models are similar except for the alternate power supplies and alternate motherboards described in this
report, and minor cosmetic differences and/or differences in software, and/or minor differences in SELV logic
circuits.
Additional Information
Some of the attached component Licenses are greater than 3 years old, an accepting NCB may request
updated Licenses for these components.
The CB Certificates for the Power Supplies are provided as an attachment in this Report; the manufacturer
will provide the complete CB Report upon request from the accepting NCB.
Technical Considerations
The product was submitted and evaluated for use at the maximum ambient temperature (Tma) permitted by
the manufacturer’s specification of: 40 °C
The means of connection to the mains supply is: Pluggable A
The product is intended for use on the following power systems: TN, IT (Norway)
The equipment disconnect device is considered to be: Appliance Inlet
The class of laser product is: Incorporates previously certified Class 1 laser source (CD/DVD drive)
The product was investigated to the following additional standards: EN 60950-1:2001 + A11:2004 (which
includes all European national differences, including those specified in this test report).
The following circuit locations (with circuit/schematic designation) were investigated as a limited power
source (LPS): All external I/O connectors
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 8 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
1
GENERAL
Pass
1.5
Components
Pass
1.5.1
General
Pass
Comply with IEC 60950 or relevant component
standard
Reference Table 1.5.1.
Verdict
Pass
1.5.2
Evaluation and testing of components
Pass
1.5.3
Thermal controls
N/A
1.5.4
Transformers
Evaluated in separate
certification of power supply.
N/A
1.5.5
Interconnecting cables
Interconnecting cables not
provided.
N/A
1.5.6
Capacitors in primary circuits ................................ : Evaluated in separate
certification of power supply.
N/A
1.5.7
Double insulation or reinforced insulation bridged
by components
N/A
1.5.7.1
General
N/A
1.5.7.2
Bridging capacitors
N/A
1.5.7.3
Bridging resistors
N/A
1.5.7.4
Accessible parts
N/A
1.5.8
Components in equipment for IT power systems
1.6
Power interface
Pass
1.6.1
AC power distribution systems
Pass
1.6.2
Input current
1.6.3
Voltage limit of hand-held equipment
N/A
1.6.4
Neutral conductor
Pass
TRF No.: IEC60950__1B
Line-to-earth capacitors rated
for line-to-line system voltage.
Reference Table 1.6.2.
Underwriters Laboratories Inc.
Pass
Pass
Issue Date:
2009-06-16
Page 9 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
1.7
Marking and instructions
Pass
1.7.1
Power rating
Pass
Rated voltage(s) or voltage range(s) (V) ............... : Refer to the Rating information
at the beginning of this Test
Report.
Pass
Symbol for nature of supply, for d.c. only .............. :
N/A
Rated frequency or rated frequency range (Hz).... : Refer to the Rating information
at the beginning of this Test
Report.
Pass
Rated current (mA or A) ........................................ : Refer to the Rating information
at the beginning of this Test
Report.
Pass
Manufacturer's name or trademark or identification Refer to the Rating information
mark....................................................................... : at the beginning of this Test
Report.
Pass
Type/model or type reference ............................... : Refer to the Rating information
at the beginning of this Test
Report.
Pass
Symbol for Class II equipment only....................... :
N/A
Other symbols ....................................................... :
N/A
Certification marks................................................. : UL, C-UL.
Pass
1.7.2
Safety instructions
Pass
1.7.3
Short duty cycles
N/A
1.7.4
Supply voltage adjustment .................................... :
N/A
1.7.5
Power outlets on the equipment............................ :
N/A
1.7.6
Fuse identification.................................................. : Fuse identification provided in
power supply; evaluated in
separate certification of power
supply.
N/A
1.7.7
Wiring terminals
N/A
1.7.7.1
Protective earthing and bonding terminals ............ :
N/A
1.7.7.2
Terminal for a.c. mains supply conductors
N/A
1.7.7.3
Terminals for d.c. mains supply conductors
N/A
1.7.8
Controls and indicators
Pass
1.7.8.1
Identification, location and marking ....................... : The function of controls
Pass
TRF No.: IEC60950__1B
Result - Remark
Operating/safety instructions
made available to the user.
Underwriters Laboratories Inc.
Verdict
Issue Date:
2009-06-16
Page 10 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
affecting safety is obvious
regardless of language.
1.7.8.2
Colours .................................................................. : Only functional indicators use
color.
Pass
1.7.8.3
Symbols according to IEC 60417 .......................... : The stand-by symbol (604171-IEC-5009) is marked on the
front panel standby switch.
Pass
1.7.8.4
Markings using figures........................................... :
N/A
1.7.9
Isolation of multiple power sources ....................... : Marking states following or
equivalent, "Disconnect all
power sources before
servicing."
Pass
1.7.10
IT power distribution systems
Pass
1.7.11
Thermostats and other regulating devices
1.7.12
Language............................................................... : Reviewed English
markings/instructions. May be
provided in other languages
upon request from the
manufacturer.
1.7.13
Durability
The marking(s) withstood the
required test.
Pass
1.7.14
Removable parts
Required markings not located
on removable parts.
Pass
1.7.15
Replaceable batteries
The lithium battery is not
located in an Operator Access
Area. The required warning is
in the service manual.
Pass
Suitable installation
instructions are provided
(Norway).
N/A
Language............................................................... : Reviewed only English
instruction. Reference
Enclosures, Miscellaneous,
manufacturer's Declaration.
-
-
1.7.16
Operator access with a tool ................................... : The inside of the equipment is
for access by trained service
persons only.
N/A
1.7.17
Equipment for restricted access locations............. :
N/A
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 11 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
2
PROTECTION FROM HAZARDS
Pass
2.1
Protection from electric shock and energy hazards
Pass
2.1.1
Protection in operator access areas
The inside of the equipment is
for access by trained service
persons only.
Pass
2.1.1.1
Access to energized parts
No operator access to
energized parts.
Pass
Test by inspection.................................................. : The operator does not have
access to parts specified in cl.
2.1.1.1.
Pass
Test with test finger................................................ : The test finger was not able to
contact the parts specified in
cl. 2.1.1.1.
Pass
Test with test pin.................................................... : The test pin was unable to
contact bare hazardous parts.
Pass
Test with test probe ............................................... : No TNV circuits in the
equipment.
N/A
2.1.1.2
Battery compartments............................................ :
N/A
2.1.1.3
Access to ELV wiring
N/A
Working voltage (V); minimum distance (mm)
through insulation .................................................. :
-
2.1.1.4
Access to hazardous voltage circuit wiring
N/A
2.1.1.5
Energy hazards...................................................... : The operator does not have
access to hazardous energy
parts. The inside of the
equipment is for access by
trained service persons only.
Pass
2.1.1.6
Manual controls
N/A
2.1.1.7
Discharge of capacitors in equipment
Evaluated in separate
certification of power supply.
Time-constant (s); measured voltage (V) .............. :
N/A
-
2.1.2
Protection in service access areas
Pass
2.1.3
Protection in restricted access locations
N/A
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 12 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
2.2
SELV circuits
Pass
2.2.1
General requirements
Pass
2.2.2
Voltages under normal conditions (V) ................... : All accessible voltages are
less than 42.4 Vp or 60 V dc
and are classified as SELV.
Maximum output voltage of
power supply is 12 Vdc.
Maximum accessible
connector voltage is 5.1Vdc.
Pass
2.2.3
Voltages under fault conditions (V)........................ : Under fault conditions voltages
never exceed 71V peak and
120Vdc and do not exceed
42.4V peak or 60V dc for more
than 0.2 sec. Evaluated in
separate certification of power
supply. Maximum output
voltage of power supply is 12
Vdc. Maximum accessible
connector voltage is 5.1Vdc.
Pass
2.2.3.1
Separation by double insulation or reinforced
insulation (method 1)
N/A
2.2.3.2
Separation by earthed screen (method 2)
N/A
2.2.3.3
Protection by earthing of the SELV circuit (method
3)
N/A
2.2.4
Connection of SELV circuits to other circuits......... : SELV circuits are only
connected to other SELV
circuits.
Pass
TRF No.: IEC60950__1B
Result - Remark
Evaluated in separate
certification of power supply.
Underwriters Laboratories Inc.
Verdict
Issue Date:
2009-06-16
Page 13 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
2.3
TNV circuits
2.3.1
Limits
2.3.2
2.3.3
Result - Remark
N/A
Equipment does not have
connection to TNV circuits.
N/A
Type of TNV circuits .............................................. :
-
Separation from other circuits and from accessible
parts
N/A
Insulation employed............................................... :
-
Separation from hazardous voltages
Insulation employed............................................... :
2.3.4
Verdict
Connection of TNV circuits to other circuits
Insulation employed............................................... :
N/A
N/A
-
2.3.5
Test for operating voltages generated externally
N/A
2.4
Limited current circuits
N/A
2.4.1
General requirements
N/A
2.4.2
Limit values
N/A
2.4.3
Frequency (Hz) ...................................................... :
-
Measured current (mA).......................................... :
-
Measured voltage (V) ............................................ :
-
Measured capacitance (mF) .................................. :
-
Connection of limited current circuits to other
circuits
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
N/A
Issue Date:
2009-06-16
Page 14 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.5
Limited power sources
Pass
Inherently limited output
N/A
Impedance limited output
Data pins of the RJ-45
ethernet connectors, the USB
connectors, the RS232, VGA,
Keyboard and Mouse
connectors are Limited Power
Source by impedance of the
logic circuits.
Verdict
Pass
Power pins of the Keyboard,
Mouse, USB and VGA
connectors are Limited Power
Source by impedance of the
PTC devices. Reference
Table 1.5.1
Overcurrent protective device limited output
N/A
Regulating network limited output under normal
operating and single fault condition
N/A
Regulating network limited output under normal
operating conditions and overcurrent protective
device limited output under single fault condition
N/A
Output voltage (V), output current (A), apparent
Power pin of following
power (VA):............................................................ : connectors:
Keyboard:
4.95V, 3.4A, 13.6VA;
Mouse:
4.94V, 3.4A, 13.6VA;
USB:
5.1V, 3.55A, 13.9VA
VGA port:
5.1V, 3.76A, 16.7VA
-
Current rating of overcurrent protective device (A) : Reference Table 1.5.1 for PTC
device ratings.
-
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 15 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.6
Provisions for earthing and bonding
Pass
2.6.1
Protective earthing
Pass
2.6.2
Functional earthing
N/A
2.6.3
Protective earthing and protective bonding
conductors
Pass
2.6.3.1
General
Pass
2.6.3.2
Size of protective earthing conductors
For North America, the
protective earthing conductor
is located in the optional power
supply cord and is sized in
accordance with the
NEC/CEC.
Verdict
Pass
Reference Enclosures,
Miscellaneous, Manufacturer's
Letter of Assurance for other
countries.
Rated current (A), cross-sectional area (mm2),
For North America:
AWG ...................................................................... : 11A max., 16 AWG min.
2.6.3.3
Size of protective bonding conductors
Evaluated in separate
certification of power supply.
Rated current (A), cross-sectional area (mm2),
Evaluated in separate
AWG ...................................................................... : certification of power supply.
N/A
-
2.6.3.4
Resistance (Ohm) of earthing conductors and their Evaluated in separate
terminations, test current (A) ................................. : certification of power supply.
All primary hazardous voltages
are located within the complete
metal enclosure of the power
supply. All circuits outside the
power supply are SELV.
N/A
2.6.3.5
Colour of insulation ................................................ : Green / Yellow
Pass
2.6.4
Terminals
Pass
2.6.4.1
General
Pass
2.6.4.2
Protective earthing and bonding terminals
Earthing Pin of Appliance Inlet
is the Main Protective Earthing
Terminal.
Pass
Protective Bonding terminals
were evaluated in separate
certification of power supply.
Rated current (A), type and nominal thread
TRF No.: IEC60950__1B
Earthing Pin of Appliance Inlet
Underwriters Laboratories Inc.
-
Issue Date:
2009-06-16
Page 16 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
diameter (mm) ....................................................... : is the Main Protective Earthing
Terminal.
Protective Bonding terminals
were evaluated in separate
certification of power supply.
2.6.4.3
Separation of the protective earthing conductor
from protective bonding conductors
Pass
2.6.5
Integrity of protective earthing
Pass
2.6.5.1
Interconnection of equipment
N/A
2.6.5.2
Components in protective earthing conductors and No components in Protective
protective bonding conductors
Earthing or Protective Bonding
conductors.
Pass
2.6.5.3
Disconnection of protective earth
N/A
2.6.5.4
Parts that can be removed by an operator
Pass
2.6.5.5
Parts removed during servicing
Pass
2.6.5.6
Corrosion resistance
Complied with Annex J.
Pass
2.6.5.7
Screws for protective bonding
No self-tapping or spaced
thread screws used for
protective bonding.
N/A
2.6.5.8
Reliance on telecommunication network or cable
distribution system
N/A
2.7
Overcurrent and earth fault protection in primary circuits
Pass
2.7.1
Basic requirements
Pass
Instructions when protection relies on building
installation
Equipment is Pluggable Type
A.
N/A
2.7.2
Faults not covered in 5.3
2.7.3
Short-circuit backup protection
Equipment is Pluggable Type
A. The building installation
provides the short-circuit
backup protection.
Pass
2.7.4
Number and location of protective devices............ : Fuse in the "live" phase in the
power supply.
Pass
2.7.5
Protection by several devices
N/A
2.7.6
Warning to service personnel ................................ :
N/A
TRF No.: IEC60950__1B
N/A
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 17 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
2.8
Safety interlocks
N/A
2.8.1
General principles
N/A
2.8.2
Protection requirements
N/A
2.8.3
Inadvertent reactivation
N/A
2.8.4
Fail-safe operation
N/A
2.8.5
Moving parts
N/A
2.8.6
Overriding
N/A
2.8.7
Switches and relays
N/A
2.8.7.1
Contact gaps (mm) ................................................ :
N/A
2.8.7.2
Overload test
N/A
2.8.7.3
Endurance test
N/A
2.8.7.4
Electric strength test
N/A
2.8.8
Mechanical actuators
N/A
2.9
Electrical insulation
Pass
2.9.1
Properties of insulating materials
Natural rubber, materials
containing asbestos and
hygroscopic materials are not
used as insulation.
Pass
2.9.2
Humidity conditioning
Evaluated in separate
certification of power supply.
N/A
2.9.3
Result - Remark
Verdict
Humidity (%) .......................................................... :
-
Temperature (°C)................................................... :
-
Grade of insulation
TRF No.: IEC60950__1B
Basic and Functional. Primary
to Secondary evaluated in
separate power supply
investigation.
Underwriters Laboratories Inc.
Pass
Issue Date:
2009-06-16
Page 18 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.10
Clearances, creepage distances and distances through insulation
Pass
2.10.1
General
Pass
2.10.2
Determination of working voltage
Pass
2.10.3
Clearances
Pass
2.10.3.1
General
Pass
2.10.3.2
Clearances in primary circuit
All primary circuit clearances
were evaluated in separate
certification of power supply.
N/A
2.10.3.3
Clearances in secondary circuits
Reference Cl. 5.3.4c.
Pass
2.10.3.4
Measurement of transient voltage levels
2.10.4
Creepage distances
Pollution Degree 2 applicable.
Verdict
N/A
Creepage distances in primary
circuits were evaluated in
separate certification of power
supply. Reference cl. 5.3.4c
for creepage distances in
secondary circuits.
CTI tests................................................................. : Material group IIIb; 100 <=CTI
<175.
Pass
-
2.10.5
Solid insulation
Evaluated in separate
certification of power supply.
N/A
2.10.5.1
Minimum distance through insulation
Evaluated in separate
certification of power supply.
N/A
2.10.5.2
Thin sheet material
Evaluated in separate
certification of power supply.
N/A
2.10.5.3
2.10.5.4
2.10.6
Number of layers (pcs) .......................................... :
-
Electric strength test .............................................. :
-
Printed boards
N/A
Distance through insulation
N/A
Electric strength test for thin sheet insulating
material .................................................................. :
-
Number of layers (pcs) .......................................... :
N/A
Wound components
N/A
Number of layers (pcs) .......................................... :
N/A
Two wires in contact inside wound component;
angle between 45° and 90° ................................... :
N/A
Coated printed boards
N/A
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 19 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
2.10.6.1
General
N/A
2.10.6.2
Sample preparation and preliminary inspection
N/A
2.10.6.3
Thermal cycling
N/A
2.10.6.4
Thermal ageing (°C) .............................................. :
N/A
2.10.6.5
Electric strength test .............................................. :
-
2.10.6.6
Abrasion resistance test
2.10.7
2.10.8
Result - Remark
Verdict
N/A
Electric strength test .............................................. :
-
Enclosed and sealed parts .................................... :
N/A
Temperature T1=T2 = Tma - Tamb +10K (°C)...... :
N/A
Spacings filled by insulating compound................. : Evaluated in separate
certification of power supply.
N/A
Electric strength test .............................................. :
-
2.10.9
Component external terminations
N/A
2.10.10
Insulation with varying dimensions
N/A
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 20 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
3
WIRING, CONNECTIONS AND SUPPLY
Pass
3.1
General
Pass
3.1.1
Current rating and overcurrent protection
Pass
3.1.2
Protection against mechanical damage
Pass
3.1.3
Securing of internal wiring
Pass
3.1.4
Insulation of conductors
Pass
3.1.5
Beads and ceramic insulators
3.1.6
Screws for electrical contact pressure
3.1.7
Insulating materials in electrical connections
The equipment does not have
any electrical connections that
rely on insulating material for
adequate contact pressure.
Pass
3.1.8
Self-tapping and spaced thread screws
Thread-cutting or spaced
thread screws are not used for
electrical connections.
Machine screws only.
Pass
3.1.9
Termination of conductors
10 N pull test
3.1.10
Result - Remark
Not used.
N/A
Pass
Pass
Complied by inspection.
Sleeving on wiring
TRF No.: IEC60950__1B
Verdict
N/A
N/A
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 21 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
3.2
Connection to an a.c. mains supply or a d.c. mains supply
Pass
3.2.1
Means of connection
Pass
3.2.1.1
Connection to an a.c. mains supply
Pass
3.2.1.2
Connection to a d.c. mains supply
N/A
3.2.2
Multiple supply connections
Pass
3.2.3
Permanently connected equipment
N/A
Appliance Inlet
Number of conductors, diameter (mm) of cable and
conduits.................................................................. :
Verdict
-
3.2.4
Appliance inlets
The appliance inlet is
separately certified and
complies with IEC 60320.
Pass
3.2.5
Power supply cords
Manufacturer may provide
optional power cord for North
America only.
Pass
Reference Enclosures,
Miscellaneous, Manufacturer's
Letter of Assurance for other
countries.
3.2.5.1
AC power supply cords
Manufacturer may provide
optional power cord for North
America only.
Pass
Reference Enclosures,
Miscellaneous, Manufacturer's
Letter of Assurance for other
countries.
Type ....................................................................... : For North America: SVT or
SJT
-
Rated current (A), cross-sectional area (mm²),
For North America:
AWG ...................................................................... : 11A, 16 AWG minimum
-
3.2.5.2
DC power supply cords
N/A
3.2.6
Cord anchorages and strain relief
N/A
Mass of equipment (kg), pull (N) ........................... :
-
Longitudinal displacement (mm)............................ :
-
3.2.7
Protection against mechanical damage
Pass
3.2.8
Cord guards
N/A
D (mm); test mass (g) ............................................ :
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
-
Issue Date:
2009-06-16
Page 22 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Radius of curvature of cord (mm) .......................... :
Verdict
-
3.2.9
Supply wiring space
N/A
3.3
Wiring terminals for connection of external conductors
N/A
3.3.1
Wiring terminals
N/A
3.3.2
Connection of non-detachable power supply cords
N/A
3.3.3
Screw terminals
N/A
3.3.4
Conductor sizes to be connected
N/A
Rated current (A), cord/cable type, cross-sectional
area (mm²) ............................................................. :
3.3.5
Wiring terminal sizes
N/A
Rated current (A), type and nominal thread
diameter (mm) ....................................................... :
-
3.3.6
Wiring terminals design
N/A
3.3.7
Grouping of wiring terminals
N/A
3.3.8
Stranded wire
N/A
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 23 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
3.4
Disconnection from the mains supply
Pass
3.4.1
General requirement
Pass
3.4.2
Disconnect devices
3.4.3
Permanently connected equipment
N/A
3.4.4
Parts which remain energized
N/A
3.4.5
Switches in flexible cords
N/A
3.4.6
Single-phase equipment and d.c. equipment
Pass
3.4.7
Three-phase equipment
N/A
3.4.8
Switches as disconnect devices
N/A
3.4.9
Plugs as disconnect devices
N/A
3.4.10
Interconnected equipment
N/A
3.4.11
Multiple power sources
3.5
Interconnection of equipment
Pass
3.5.1
General requirements
Pass
3.5.2
Types of interconnection circuits ........................... : Interconnection circuits are
SELV circuits.
Pass
3.5.3
ELV circuits as interconnection circuits
N/A
4
PHYSICAL REQUIREMENTS
Pass
4.1
Stability
Pass
Angle of 10°
Result - Remark
Appliance Inlet
Marking states following or
equivalent, "Disconnect all
power sources before
servicing."
Unit does not overbalance at
10º.
Test: force (N)........................................................ : Floor-standing unit does not
overbalance when a force of
51N is applied. Floor-standing
unit does not overbalance
when a downward force of 800
N (180 lbs) is applied.
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Verdict
Pass
Pass
Pass
Pass
Issue Date:
2009-06-16
Page 24 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
4.2
Mechanical strength
Pass
4.2.1
General
Pass
4.2.2
Steady force test, 10 N
4.2.3
Steady force test, 30 N
4.2.4
Steady force test, 250 N
Enclosure is metal, minimum
thickness 0.8mm. Complied by
inspection.
Pass
4.2.5
Impact test
Equipment overall enclosure is
metal, minimum thickness 0.8
mm. Complied by inspection.
Pass
Fall test
Equipment overall enclosure is
metal, minimum thickness 0.8
mm. Complied by inspection.
Pass
Evaluated in separate
certification of power supply.
Verdict
N/A
N/A
Swing test
N/A
4.2.6
Drop test
N/A
4.2.7
Stress relief test
4.2.8
Cathode ray tubes
N/A
Picture tube separately certified ............................ :
N/A
4.2.9
High pressure lamps
N/A
4.2.10
Wall or ceiling mounted equipment; force (N) ....... :
N/A
TRF No.: IEC60950__1B
Equipment enclosure is metal.
Front bezels are decorative.
Underwriters Laboratories Inc.
N/A
Issue Date:
2009-06-16
Page 25 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
4.3
Design and construction
Pass
4.3.1
Edges and corners
Pass
4.3.2
Handles and manual controls; force (N) ................ :
N/A
4.3.3
Adjustable controls
N/A
4.3.4
Securing of parts
Pass
4.3.5
Connection of plugs and sockets
Pass
4.3.6
Direct plug-in equipment
N/A
Dimensions (mm) of mains plug for direct plug-in . :
N/A
Torque and pull test of mains plug for direct plug-in;
torque (Nm); pull (N) .............................................. :
N/A
4.3.7
Heating elements in earthed equipment
N/A
4.3.8
Batteries
4.3.9
Oil and grease
N/A
4.3.10
Dust, powders, liquids and gases
N/A
4.3.11
Containers for liquids or gases
N/A
4.3.12
Flammable liquids.................................................. :
N/A
Quantity of liquid (l)................................................ :
N/A
Flash point (°C)...................................................... :
N/A
4.3.13
Result - Remark
Lithium Battery on the
motherboard is protected by
1kOhm Resistor, and Diode in
series. Reference Table 1.5.1.
Radiation; type of radiation
Equipment employs non-laser
type LEDs for functional
indicators only.
Verdict
Pass
Pass
Equipment employs an
optional CD/DVD drive which
is a Class 1 laser product;
reference Table 1.5.1.
4.3.13.1
General
Pass
4.3.13.2
Ionizing radiation
N/A
Measured radiation (pA/kg) ................................... :
-
Measured high-voltage (kV)................................... :
-
Measured focus voltage (kV) ................................. :
-
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 26 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
CRT markings........................................................ :
4.3.13.3
Verdict
-
Effect of ultraviolet (UV) radiation on materials
N/A
Part, property, retention after test, flammability
classification .......................................................... :
N/A
4.3.13.4
Human exposure to ultraviolet (UV) radiation........ :
N/A
4.3.13.5
Laser (including LEDs)
Equipment employs non-laser
type LEDs for functional
indicators only.
Pass
Equipment employs an
optional CD/DVD drive which
is a Class 1 laser product;
reference Table 1.5.1.
Laser class............................................................. : Equipment employs non-laser
type LEDs for functional
indicators only.
-
Equipment employs an
optional CD/DVD drive which
is a Class 1 laser product;
reference Table 1.5.1.
4.3.13.6
Other types ............................................................ :
N/A
4.4
Protection against hazardous moving parts
Pass
4.4.1
General
Pass
4.4.2
Protection in operator access areas
Pass
4.4.3
Protection in restricted access locations
N/A
4.4.4
Protection in service access areas
TRF No.: IEC60950__1B
Unintentional contact with
hazardous moving parts is
unlikely.
Underwriters Laboratories Inc.
Pass
Issue Date:
2009-06-16
Page 27 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
4.5
Thermal requirements
4.5.1
Maximum temperatures
Verdict
Pass
Reference Table 4.5.
Pass
Normal load condition per Annex L ....................... : Operated in the most
unfavorable way of operation
given in the operating
instructions until steady
conditions established.
Permitted rises based on
manufacturer's specified Tmra
of 40°C.
Pass
4.5.2
Resistance to abnormal heat
N/A
4.6
Openings in enclosures
4.6.1
Top and side openings
Evaluated in separate
certification of power supply.
Pass
Foreign objects entering the
enclosure will not contact bare
parts at hazardous voltage or
energy. (No hazardous parts
within 5° projection).
Dimensions (mm)................................................... : Top, Left, Right: No openings.
Pass
-
Rear: 14.8mm by 3.9mm slots
and irregular shaped fan
ventilation openings slots.
Front: 5.7mm by 5.7mm slots;
12mm by 3mm slots.
4.6.2
Bottoms of fire enclosures
Pass
Construction of the bottom..................................... : No openings except 20.6mm
by 0.9mm slots under disk
drive bay and unused 3.5mm
diameter screw holes which
are covered by internal barrier
sheet; reference Table 1.5.1.
The inside of the equipment is
only for access by qualified
service persons.
-
4.6.3
Doors or covers in fire enclosures
4.6.4
Openings in transportable equipment
N/A
4.6.5
Adhesives for constructional purposes
N/A
Conditioning temperature (°C)/time (weeks) ......... :
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
N/A
-
Issue Date:
2009-06-16
Page 28 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
4.7
Resistance to fire
4.7.1
Reducing the risk of ignition and spread of flame
Verdict
Pass
Method 1
Pass
Method 1, selection and application of components
wiring and materials
Pass
Method 2, application of all of simulated fault
condition tests
N/A
4.7.2
Conditions for a fire enclosure
Pass
4.7.2.1
Parts requiring a fire enclosure
4.7.2.2
Parts not requiring a fire enclosure
N/A
4.7.3
Materials
Pass
4.7.3.1
General
The propagation of fire is
minimized through the fire
enclosure construction.
Pass
4.7.3.2
Materials for fire enclosures
Metal
Pass
4.7.3.3
Materials for components and other parts outside
fire enclosures
Front bezels and top panel are
min. HB.
Pass
4.7.3.4
Materials for components and other parts inside fire All internal materials are rated
enclosures
V-2 or HF-2 or better, or are
mounted on a Printed Circuit
Board rated V-1 or better.
Internal wiring is UL
Recognized, rated VW-1 or
FT-1.
Pass
4.7.3.5
Materials for air filter assemblies
Pass
4.7.3.6
Materials used in high-voltage components
TRF No.: IEC60950__1B
A fire enclosure covers all
parts.
Air filter behind front disk drive
door is outside the fire
enclosure, and separated from
electrical parts by at least 13
mm of air.
Underwriters Laboratories Inc.
Pass
N/A
Issue Date:
2009-06-16
Page 29 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
5
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS
Pass
5.1
Touch current and protective conductor current
N/A
5.1.1
General
5.1.2
Equipment under test (EUT)
N/A
5.1.3
Test circuit
N/A
5.1.4
Application of measuring instrument
N/A
5.1.5
Test procedure
N/A
5.1.6
Test measurements
N/A
Evaluated in separate
certification of power supply.
All primary hazardous voltages
are located within the complete
metal enclosure of the power
supply. All circuits outside the
power supply are SELV.
Verdict
N/A
Test voltage (V) ..................................................... :
-
Measured touch current (mA) ................................ :
-
Max. allowed touch current (mA)........................... :
-
Measured protective conductor current (mA) ........ :
-
Max. allowed protective conductor current (mA) ... :
-
5.1.7
Equipment with touch current exceeding 3.5 mA .. :
N/A
5.1.8
Touch currents to and from telecommunication
networks and cable distribution systems and from
telecommunication networks
N/A
5.1.8.1
Limitation of the touch current to a
telecommunication network and a cable distribution
system
N/A
Test voltage (V) ..................................................... :
-
Measured touch current (mA) ................................ :
-
Max. allowed touch current (mA)........................... :
-
Summation of touch currents from
telecommunication networks ................................. :
N/A
5.1.8.2
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 30 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
5.2
Electric strength
5.2.1
General
5.2.2
Test procedure
Pass
5.3
Abnormal operating and fault conditions
Pass
5.3.1
Protection against overload and abnormal
operation
Pass
5.3.2
Motors
Motors of ventilation fan and
internal storage drives were
evaluated in separate
certification. Reference Table
1.5.1.
N/A
5.3.3
Transformers
Evaluated in separate
certification of power supply.
N/A
5.3.4
Functional insulation .............................................. : Method C.
Pass
5.3.5
Electromechanical components
N/A
5.3.6
Simulation of faults
5.3.7
Unattended equipment
N/A
5.3.8
Compliance criteria for abnormal operating and
fault conditions
Pass
6
CONNECTION TO TELECOMMUNICATION NETWORKS
N/A
6.1
Protection of telecommunication network service persons, and users of other
equipment connected to the network, from hazards in the equipment
N/A
6.1.1
Protection from hazardous voltages
N/A
6.1.2
Separation of the telecommunication network from earth
N/A
6.1.2.1
Requirements
N/A
6.1.2.2
Result - Remark
Verdict
Pass
Reference Table 5.2.
Reference Table 5.3.
Equipment does not have
connections to TNV circuits.
Pass
Pass
Test voltage (V) ..................................................... :
-
Current in the test circuit (mA) ............................... :
-
Exclusions.............................................................. :
N/A
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 31 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
6.2
Protection of equipment users from overvoltages on telecommunication
networks
N/A
6.2.1
Separation requirements
N/A
6.2.2
Electric strength test procedure
N/A
6.2.2.1
Impulse test
N/A
6.2.2.2
Steady-state test
N/A
6.2.2.3
Compliance criteria
N/A
6.3
Protection of the telecommunication wiring system from overheating
N/A
Max. output current (A) .......................................... :
-
Current limiting method.......................................... :
-
7
CONNECTION TO CABLE DISTRIBUTION SYSTEMS
N/A
7.1
Protection of cable distribution system service persons, and users of other
equipment connected to the system, from hazardous voltages in the equipment
N/A
7.2
Protection of equipment users from overvoltages
on the cable distribution system
N/A
7.3
Insulation between primary circuits and cable
distribution systems
N/A
7.3.1
General
N/A
7.3.2
Voltage surge test
N/A
7.3.3
Impulse test
N/A
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 32 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
A
Annex A, TESTS FOR RESISTANCE TO HEAT AND FIRE
Pass
A.1
Flammability test for fire enclosures of movable equipment having a total mass
exceeding 18 kg, and of stationary equipment (see 4.7.3.2)
Pass
A.1.1
Samples ................................................................. : 1. Barrier Sheet #1, General
Electric, FR-65, 0.2mm
thickness, color=translucent;
-
2. Barrier Sheet #2, General
Electric, FR-700, 0.254mm
thickness, color=black.
Wall thickness (mm) .............................................. : 1. Barrier Sheet #1: 0.2mm
thickness;
-
2. Barrier Sheet #2: 0.254mm
thickness.
A.1.2
Conditioning of samples; temperature (°C) ........... : 1. Barrier Sheet #1: 70 C
Pass
2. Barrier Sheet #2: 70 C
A.1.3
Mounting of samples.............................................. : 1. Barrier Sheet #1: Mounted
to bottom of chassis sample,
over openings
Pass
2. Barrier Sheet #2: Mounted
to bottom of chassis sample,
over openings.
A.1.4
Test flame
125mm with inner blue cone of
40mm for fixed, stationary
equipment over 18kg.
Pass
A.1.5
Test procedure
The edge of the inner cone of
the flame was applied to the
same location for 5 seconds,
then removed for 5 seconds,
until five applications of the
flame had been made. Three
different sample pieces of
each barrier sheet material
were tested.
Pass
A.1.6
Compliance criteria
During the test, the samples
shall not release either flaming
drops or particles capable of
igniting the surgical cotton.
The sample shall not continue
to burn for more than one
minute after the fifth
application of the test flame,
Pass
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 33 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
and shall not be consumed
completely.
Sample 1 burning time (s)...................................... : 1. Barrier Sheet #1: 0 s
-
2. Barrier Sheet #2: 0 s
Sample 2 burning time (s)...................................... : 1. Barrier Sheet #1: 0 s
-
2. Barrier Sheet #2: 0 s
Sample 3 burning time (s)...................................... : 1. Barrier Sheet #1: 0 s
-
2. Barrier Sheet #2: 0 s
N/A
A.2
Flammability test for fire enclosures of movable equipment having a total
mass not exceeding 18 kg, and for material and components located inside
fire enclosures (see 4.7.3.2 and 4.7.3.4)
A.2.1
Samples, material .................................................. :
-
Wall thickness (mm) .............................................. :
-
A.2.2
Conditioning of samples
N/A
A.2.3
Mounting of samples
N/A
A.2.4
Test flame
N/A
A.2.5
Test procedure
N/A
A.2.6
Compliance criteria
N/A
A.2.7
Sample 1 burning time (s)...................................... :
-
Sample 2 burning time (s)...................................... :
-
Sample 3 burning time (s)...................................... :
-
Alternative test acc. to IEC 60695-2-2, cl. 4, 8
N/A
Sample 1 burning time (s)...................................... :
-
Sample 2 burning time (s)...................................... :
-
Sample 3 burning time (s)...................................... :
-
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 34 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
A.3
Hot flaming oil test (see 4.6.2)
N/A
A.3.1
Mounting of samples
N/A
A.3.2
Test procedure
N/A
A.3.3
Compliance criterion
N/A
B
Annex B, MOTOR TESTS UNDER ABNORMAL CONDITIONS(see 4.7.2.2 and
5.3.2)
N/A
B.1
General requirements
N/A
Motors of ventilation fans and
internal storage drives were
evaluated in separate
certification. Reference Table
1.5.1.
Verdict
Position .................................................................. :
-
Manufacturer.......................................................... :
-
Type ....................................................................... :
-
Rated values.......................................................... :
-
B.2
Test conditions
N/A
B.3
Maximum temperatures
N/A
B.4
Running overload test
N/A
B.5
Locked-rotor overload test
N/A
Test duration (days)............................................... :
-
Electric strength test: test voltage (V).................... :
-
B.6
Running overload test for d.c. motors in secondary
circuits
N/A
B.7
Locked-rotor overload test for d.c. motors in secondary circuits
N/A
B.7.1
Test procedure
N/A
B.7.2
Alternative test procedure; test time (h)................. :
N/A
B.7.3
Electric strength test
N/A
B.8
Test for motors with capacitors
N/A
B.9
Test for three-phase motors
N/A
B.10
Test for series motors
N/A
Operating voltage (V)............................................. :
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
-
Issue Date:
2009-06-16
Page 35 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
C
Annex C, TRANSFORMERS (see 1.5.4 and 5.3.3)
Verdict
N/A
Position .................................................................. : Evaluated in separate
certification of power supply.
-
Manufacturer.......................................................... :
-
Type ....................................................................... :
-
Rated values.......................................................... :
-
Method of protection .............................................. :
-
C.1
Overload test
N/A
C.2
Insulation
N/A
Protection from displacement of windings ............. :
N/A
D
Annex D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS
N/A
D.1
Measuring instrument
N/A
D.2
Alternative measuring instrument
N/A
E
Annex E, TEMPERATURE RISE OF A WINDING
N/A
F
Annex F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES
(see 2.10)
Pass
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 36 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
G
Annex G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM
CLEARANCES
N/A
G.1
Summary of the procedure for determining
minimum clearances
N/A
G.2
Determination of mains transient voltage (V)
N/A
G.2.1
AC mains supply
N/A
G.2.2
DC mains supply
N/A
G.3
Determination of telecommunication network
transient voltage (V) :............................................. :
N/A
G.4
Determination of required withstand voltage (V) ... :
N/A
G.5
Measurement of transient levels (V)...................... :
N/A
G.6
Determination of minimum clearances .................. :
N/A
H
ANNEX H, IONIZING RADIATION (see 4.3.13)
N/A
J
Annex J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6)
Pass
Metal used ............................................................. : sheet steel
Verdict
-
K
ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.7)
N/A
K.1
Making and breaking capacity
N/A
K.2
Thermostat reliability; operating voltage (V) .......... :
N/A
K.3
Thermostat endurance test; operating voltage (V) :
N/A
K.4
Temperature limiter endurance; operating voltage
(V) .......................................................................... :
N/A
K.5
Thermal cut-out reliability
N/A
K.6
Stability of operation
N/A
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 37 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
L
Annex L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL
BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.1)
Pass
L.1
Typewriters
N/A
L.2
Adding machines and cash registers
N/A
L.3
Erasers
N/A
L.4
Pencil sharpeners
N/A
L.5
Duplicators and copy machines
N/A
L.6
Motor-operated files
N/A
L.7
Other business equipment
Pass
M
Annex M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1)
N/A
M.1
Introduction
N/A
M.2
Method A
N/A
M.3
Method B
N/A
M.3.1
Ringing signal
N/A
M.3.1.1
Frequency (Hz) ...................................................... :
-
M.3.1.2
Voltage (V)............................................................. :
-
M.3.1.3
Cadence; time (s), voltage (V)............................... :
-
M.3.1.4
Single fault current (mA) ........................................ :
-
M.3.2
Tripping device and monitoring voltage................. :
N/A
M.3.2.1
Conditions for use of a tripping device or a
monitoring voltage
N/A
M.3.2.2
Tripping device
N/A
M.3.2.3
Monitoring voltage (V)............................................ :
N/A
N
Annex N, IMPULSE TEST GENERATORS (see 2.10.3.4, 6.2.2.1, 7.3.2 and
clause G.5)
N/A
N.1
ITU-T impulse test generators
N/A
N.2
IEC 60065 impulse test generator
N/A
TRF No.: IEC60950__1B
Result - Remark
Underwriters Laboratories Inc.
Verdict
Issue Date:
2009-06-16
Page 38 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
P
Annex P, NORMATIVE REFERENCES
Pass
Q
Annex Q, BIBLIOGRAPHY
Pass
R
Annex R, EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL
PROGRAMMES
N/A
R.1
Minimum separation distances for unpopulated
coated printed boards (see 2.10.6)
N/A
R.2
Reduced clearances (see 2.10.3)
N/A
S
Annex S, PROCEDURE FOR IMPULSE TESTING (see 6.2.2.3)
N/A
S.1
Test equipment
N/A
S.2
Test procedure
N/A
S.3
Examples of waveforms during impulse testing
N/A
T
Annex T, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER (see
1.1.2)
N/A
............................................................................... :
U
Annex U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION (see 2.10.5.4)
............................................................................... :
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Verdict
-
N/A
-
Issue Date:
2009-06-16
Page 39 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
1.5.1
TABLE: list of critical components
object/part No.
Chassis /
Enclosure
(mech/elec/fire)
manufacturer/
trademark
-
Result - Remark
Pass
type/model
technical data
standard
-
Metal, minimum
thickness,
0.8mm. (overall
dimensions
550mm by
435mm by
178mm)
Min. 80ºC, for
application to
metal.
Input:
100-240V
50-60Hz,
10-4A.
dc Outputs:
+12V/66A;
+5V/18A
+5Vsb/4A
Input:
100-140V
11-7.5A
50-60Hz.
dc Outputs:
+12V/74A
+5Vsb/4A
900W;
Input:
180-240V
8-5A
50-60Hz,
dc Outputs:
+12V/100A
+5Vsb/4A
1200W
12Vdc,
0.58A
(68.2CFM)
-
mark(s) of
conformity1)
-, -
UL969
UL, -
UL60950-1
IEC60950-1
EN60950-1
UL, TUV
UL60950-1
IEC60950-1
EN60950-1
UL, TUV
UL508
EN 60950-1
UL, VDE
UL508
EN 60950-1
UL, TUV
Nameplate Label BRADLEY
material
NAMEPLATE
CORP
Power Supply
ABLECOM
TECHNOLOGY
INC
White Thermal
Mylar
Power Supply,
alternate
COMPUWARE
TECHNOLOGY
INC
PWS-1K21P-1R
Rear External
Ventilation
Fans, two
provided.
Rear External
Ventilation
Fans, alternate,
two provided.
External Rear
Fan Guard /
SANYO DENKI
CO LTD
SAN ACE 80,
Model
9G0812P1F09
SANYO DENKI
CO LTD
9G0812P1F03
12Vdc,
0.58A
(68.2CFM)
CHI MEI CORP
PA-765B
V-0, minimum
UL94
2.5mm thickness UL60950-1
TRF No.: IEC60950__1B
Verdict
PWS-801-1R
Underwriters Laboratories Inc.
UL, -
Issue Date:
2009-06-16
Page 40 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Frame
Assembly, two
provided
Mid-Chassis
Ventilation
Fans, optional,
up to three
provided
Mid-Chassis
Ventilation
Fans, optional,
alternate, up to
three provided
CPU fan
(optional)
Motherboard,
Super Micro
Computer, Model
X8 or H8 series
PTC
Thermistors, for
VGA, Mouse,
Keyboard, and
USB ports.
Note: PTC circuit
designations
may vary
between
motherboards
within the series,
however
protection
circuits are the
same.
PTC
Thermistors,
alternate, for
VGA, Mouse,
Keyboard, and
USB ports.
Note: PTC circuit
designations
may vary
between
motherboards
within the series,
however
Result - Remark
Verdict
SANYO DENKI
CO LTD
SAN ACE 80,
Model
9G0812P1F09
12Vdc,
0.58A
(68.2CFM)
UL508
EN 60950-1
UL, VDE
SANYO DENKI
CO LTD
9G0812P1F03
12Vdc,
0.58A
(68.2CFM)
UL508
EN 60950-1
UL, TUV
NIDEC
AMERICA
CORP
various
T92T12MHA7
UL508
EN 60950-1
UL, TUV
various
12Vdc
0.14A
(39.9CFM)
Min V-1;
Min.105 ºC
UL60950-1
IEC60950-1
UL, -
BOURNS INC
MF-MSMF150
6Vdc,
3A trip current.
EN60730-1
UL, TUV
TYCO
ELECTRONICS
CORP
miniSMDC150
6Vdc, 3A trip
current.
EN60730-1
UL, TUV
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 41 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
protection
circuits are the
same.
Lithium Battery
Protection Circuit
Note: Resistor
and diode circuit
designations
may vary
between
motherboards
within the series,
however
protection
circuits are the
same.
Lithium Battery
SONY ENERGY CR2032
DEVICES CORP
Lithium Battery,
alternate
Lithium Battery,
alternate
Lithium Battery,
alternate
Lithium Battery,
alternate
Lithium Battery,
alternate
Printed Circuit
Boards (SELV)
Hard Disk Drive,
optional, one to
eight provided
Front Bezel for
Hard Disk Drives
CD/DVD Drive,
optional, up to
two provided.
VARTA
CR2032
MICROBATTER
Y
PANASONIC
CR2032
CORPORATION
,
PANASONIC*C
ORPORATION
OF NORTH
AMERICA
HITACHI
CR2032
MAXELL LTD
MITSUBISHI
ELECTRIC
CORP
FDK ENERGY
CO LTD
CR2032
various
various
SEAGATE
TECHNOLOGY
LLC
various
9CA154-302,
Barracuda ES2
CR2032
various
PANASONIC
UJDA710
CORPORATION
, PANASONIC
TRF No.: IEC60950__1B
Verdict
Resistor,
1kOhm, and
Diode in series.
-
-, -
3 V, maximum
10mA reverse
current.
3 V, maximum
5mA reverse
current.
3 V, maximum
5mA reverse
current.
UL1642,
IEC60950-1
UL, -
UL1642,
IEC60950-1
UL, -
UL1642,
IEC60950-1
UL, -
3 V, maximum
10mA reverse
current.
3 V, maximum
10mA reverse
current.
3 V, maximum
10mA reverse
current.
Min V-1;
Min.105 ºC
5Vdc/0.65A12Vd
c/0.42A
UL1642,
IEC60950-1
UL, -
UL1642,
IEC60950-1
UL, -
UL1642,
IEC60950-1
UL, -
UL796
UL, -
UL60950-1
IEC60950-1
UL, TUV
Min. HB,
Min. 80 C.
5Vdc/1.8A
Class 1 Laser
Product
UL94
UL60950-1
UL60950-1
EN60950-1
EN60825-1
UL, -
Underwriters Laboratories Inc.
UL, TUV,
Issue Date:
2009-06-16
Page 42 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Floppy Disk
Drive, optional
CPU Air Guide,
Empty Disk Drive
Tray, Internal
Card Brackets,
Cover for Power
Supply Output
Board
Empty Disk Drive
Tray
Front Bezels for
Disk Drive Trays,
Front Disk Drive
Door, Plastic
Mesh/Frame
behind front disk
drive door, Top
Panel
Feet, Bottom of
Chassis, Four
Provided
Result - Remark
CORPORATION
OF NORTH
AMERICA
TEAC CORP
FD-05XYYY
Verdict
5V, 0.8A max.
UL60950-1
UL, -
various
various
Min. V-2,
Min. 80 C.
UL94
UL60950-1
UL, -
various
various
various
UL94
UL60950-1
UL94
UL60950-1
UL, -
various
Min. V-2,
Min. 80 C.
Min. HB,
Min. 80 C.
various
various
5VB, secured by
snap fit and
screw to chassis
bottom.
VTM-0, 80 C,
minimum
thickness
0.2mm, covers
bottom openings
in chassis.
VTM-0, 80 C,
minimum
thickness
0.254mm, covers
bottom openings
in chassis.
UL94
UL60950-1
UL, -
Barrier Sheet,
located on
chassis bottom,
covering bottom
openings.
SABIC
FR65
INNOVATIVE
PLASTICS US L
L C (E61257)
Barrier Sheet,
alternate, located
on chassis
bottom, covering
bottom
openings.
SABIC
FR700
INNOVATIVE
PLASTICS US L
L C (E61257)
1
UL94, UL60950- UL, 1
UL94, UL60950- UL, 1
) an asterisk indicates a mark which assures the agreed level of surveillance
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
UL, -
Issue Date:
2009-06-16
Page 43 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
1.6.2
TABLE: electrical data (in normal conditions)
fuse #
I rated (A)
Result - Remark
U (V)
P (W)
I (mA)
-
-
-
-
-
----------
-10 - 4 A
10 - 4 A
10 - 4 A
10 - 4 A
10 - 4 A
10 - 4 A
10 - 4 A
--
90
100
120
132
180
200
230
240
264
-
818
810
799
793
807
799
798
797
795
-
9.1A
8.1A
6.64A
6.01A
4.5A
4.1A
3.5A
3.37A
3.06A
-
----------
-11 - 5.5 A
11 - 5.5 A
11 - 5.5 A
11 - 5.5 A
11 - 5.5 A
11 - 5.5 A
11 - 5.5 A
11 - 5.5 A
11 - 5.5 A
--
90
100
120
132
140
160
180
200
230
240
264
900
892
897
894
890
884
1180
1175
1164
1168
1166
10A
8.9A
7.5A
6.8A
6.4A
5.5A
6.6A
5.9A
5.07A
4.88A
4.46A
Verdict
Pass
I fuse (mA) condition/status
Following Input measurements on
Model 745-8 with Ablecom PWS801-1R power supply.
-MNL1, 60Hz.
-MNL1, 60Hz.
-MNL1, 60Hz.
-MNL1, 60Hz.
-MNL1, 50Hz.
-MNL1, 50Hz.
-MNL1, 50Hz.
-MNL1, 50Hz.
-MNL1, 50Hz.
Following Input measurements on
Model 745-12 with COMPUWARE
TECHNOLOGY INC, PWS1K21P-1R power supply
-MNL2, 60Hz.
-MNL2, 60Hz.
-MNL2, 60Hz.
-MNL2, 60Hz.
MNL2, 60Hz.
MNL2, 60Hz.
-MNL2, 50Hz.
-MNL2, 50Hz.
-MNL2, 50Hz.
-MNL2, 50Hz.
-MNL2, 50Hz.
supplementary information:
MNL1 Conditions: Normal Operation at Maximum Normal Load, consisting of continuous operation with
equipment operating on one power supply, equipment running a "burn in" test program, plus external resistive
loads on the power supply as follows, so that the p/s output wattage is approximately 80% of rated. Added
Load: +5V/ 4.7A; +12V / 38.7A. MNL2 Conditions: Normal Operation at Maximum Normal Load, consisting of
continuous operation with equipment operating on one power supply, equipment running a "burn in" test
program, plus external resistive loads on the power supply as follows, so that the p/s output wattage is
approximately 80% of rated. Added Load: (90V): +5V/ 4.9A, +12V / 71.5A; (264V): +5V/ 4A; +12V / 49A.
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 44 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
2.10.3 and
2.10.4
TABLE: clearance and creepage distance measurements
clearance cl and creepage
distance dcr at/of:
-
Result - Remark
Up
(V)
-
Verdict
Pass
U r.m.s. (V) required cl
cl (mm)
(mm)
-
required
dcr (mm)
-
dcr
(mm)
-
supplementary information:
Reference cl. 5.3.4c.
2.10.5
N/A
TABLE: distance through insulation measurements
distance through insulation di at/of:
Up
(V)
test voltage (V)
required di
(mm)
di
(mm)
supplementary information:
4.5
TABLE: temperature rise measurements
See
test voltage (V) ......................................... See
below bleow
t1 (°C)........................................................ See
t2 (°C)........................................................ See
below below
Pass
-
-
-
—
-
-
-
—
-
-
-
—
maximum temperature T of part/at:
T (°C)
Model 745-8 with Ablecom PWS-801-1R
power supply.
L2 coil, p/s
L3 coil, p/s
T1 coil, p/s
T2 coil, p/s
T3 coil, p/s
T4 coil, p/s
CT1 coil, p/s
Pcb near CPU1, m/b
Pcb near CPU2, m/b
Rear top external fan, center
Top metal enclosure, outside, over power
supply
TRF No.: IEC60950__1B
Test
A1
90V
60Hz.
57.6
53.2
39.9
36.8
42.4
48
35.2
38.9
37.8
28.8
24.9
Test A2
264V
50Hz.
-
-
-
allowed
Tmax (°C)
-
45.3
43
39.8
35.2
42.1
47.6
34.7
39
37.9
28.7
25
-
-
-
89
89
94
94
94
94
74
89
89
79
54
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 45 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Ambient
Test Duration (hr.)
Model 745-12 with COMPUWARE
TECHNOLOGY INC, PWS-1K21P-1R power
supply
L1 coil, p/s
L2 coil, p/s
L3 coil, p/s
L4 coil, p/s
T1 coil, p/s
T2 coil, p/s
T3 coil, p/s
CT1 coil, p/s
PWB near T601, p/s
Pcb near CPU1, m/b
Pcb near CPU2, m/b
Rear top external fan, center
Top metal enclosure, outside, over power
supply
Ambient
Test Duration (hr.)
24.4
2.6hrs
Test
B1
90V
60Hz.
53.5
53.2
48.9
38.8
47.5
30.7
29.8
29.8
28.4
38.6
38
29.1
25.4
24.8
2.5
hrs
24.5
3.1hrs
Test B2
264V
50Hz.
-
-
-
-
40.8
41.9
40.9
38.9
52.7
30.3
29.4
29.3
27.7
36.8
36.9
28.8
25.6
-
-
-
114
114
114
114
94
94
94
114
94
89
89
79
54
24.5
2.5 hrs
-
-
-
-
temperature T of winding:
-
Verdict
R2 ( Ω)
R1 (Ω)
-
-
T (°C)
-
allowed
insulation
Tmax (°C)
class
-
supplementary information:
Product's Tma is 40 deg. C.
Allowed Tmax is adjusted for Tma.
Allowed Tmax for power supply are derived from power supply certification report.
Allowed Tmax for motherboard measurements are based on 105 C rated PCB.
Temperature stabilization was determined by review of temperature chart recordings.
Test A1, A2 Conditions: Normal Operation at Maximum Normal Load, consisting of continuous operation with
equipment operating on one power supply, equipment running a "burn in" test program, plus external resistive
loads on the power supply as follows, so that the p/s output wattage is approximately 80% of rated. Added
Load: +5V/ 4.7A; +12V / 38.7A.
Test B1, B2 Conditions: Normal Operation at Maximum Normal Load, consisting of continuous operation with
equipment operating on one power supply, equipment running a "burn in" test program, plus external resistive
loads on the power supply as follows, so that the p/s output wattage is approximately 80% of rated.
Added Load: (90V): +5V/ 4.9A, +12V / 71.5A; (264V): +5V/ 4A; +12V / 49A.
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 46 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
4.5.2
Requirement + Test
Result - Remark
Verdict
N/A
TABLE: ball pressure test of thermoplastics
allowed impression diameter (mm) ........................ :
—
part
test temperature (°C)
impression diameter
(mm)
supplementary information:
4.7
part
-
Pass
TABLE: resistance to fire
manufacturer of material
-
type of material
thickness(mm)
-
flammability
class
-
-
supplementary information:
Reference Table 1.5.1.
5.2
Pass
TABLE: electric strength tests, impulse tests and voltage surge tests
test voltage applied between:
test voltage (V)
a.c./d.c.
2600 Vdc
2877 Vdc
1. Primary (Appliance Inlet L + N) to chassis ground
2. Primary (Appliance Inlet L + N) to chassis ground
breakdown
Yes / No
No
No
supplementary information:
Note: Test voltage was based on maximum working voltage in power supply.
Test 1: Model 745-8: Power Supply = Ablecom, PWS-801-1R
Test 2: Model 745-12: Power Supply = Compuware, PWS-1K21P-1R
5.3
Pass
TABLE: fault condition tests
ambient temperature (°C) ....................................... : See below
model/type of power supply.................................... : See below
manufacturer of power supply ................................ : See below
—
rated markings of power supply ............................. : Ref. Table 1.5.1.
⎯
component fault
No.
Model
Block front
745-8 with ventilation
TRF No.: IEC60950__1B
test voltage
(V)
240V, 50Hz.
test time
2.8hrs
fuse
No.
-
fuse current
(A)
-
Underwriters Laboratories Inc.
—
—
result
NC, NT, NB
T1: 40.7C
Issue Date:
2009-06-16
Page 47 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Ablecom
PWS-8011R power
supply
openings
Model
745-8 with
Ablecom
PWS-8011R power
supply
Remove two
external fans
240V, 50Hz.
0.4hr
-
-
Model
745-12
WITH
COMPUW
ARE
TECHNOL
OGY INC,
PWS1K21P-1R
POWER
SUPPLY
Model
745-12 with
COMPUW
ARE
TECHNOL
OGY INC,
PWS1K21P-1R
power
supply
Model
745-8 with
Ablecom
PWS-8011R power
supply
Block front
ventilation
openings
240V, 50Hz.
3.4hrs
-
-
Remove two
external fans
240V, 50Hz.
0.3hr
-
-
Power Supply
Connector
Current
Interruption
Test, 50 times,
under load.
264V, 50Hz.
-
-
-
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Verdict
T2: 37.1C
T3: 43.7C
T4: 48.1C
Ambient: 24.7C
Note: T1, T2, T3, T4 are
Class B. Allowed Tmax from
Annex C, Table C.1,
adjusted for Tma=40C is
159C.
NC, NT, NB
T1: 52.8C
T2: 48C
T3: 56.7C
T4: 59.8C
Ambient: 24.5C
Note: T1, T2, T3, T4 are
Class B. Allowed Tmax from
Annex C, Table C.1,
adjusted for Tma=40C is
159C.
NC, NT, NB
T1: 47.1C
T2: 31C
T3 : 30.1C
Ambient: 24.1C
Note: T1, T2, T3, are Class
B. Allowed Tmax from
Annex C, Table C.1,
adjusted for Tma=40C is
159C.
NC, NT, NB
T1: 66.6C
T2: 46.6C
T3: 45.2C
Ambient: 25.1C
Note: T1, T2, T3, are Class
B. Allowed Tmax from
Annex C, Table C.1,
adjusted for Tma=40C is
160C.
There was no visible pitting
of the contacts. The unit
functioned normally after
the test. There was no
indication of carbon tracking
that reduced spacings.
There was no indication of
Issue Date:
2009-06-16
Page 48 of 48
Report Reference #
E209323-A50-CB-1
IEC 60950-1
Clause
Model
745-12 with
COMPUW
ARE
TECHNOL
OGY INC,
PWS1K21P-1R
power
supply
Requirement + Test
Power Supply
Connector
Current
Interruption
Test, 50 times,
under load.
Result - Remark
264V, 50Hz.
-
-
-
Verdict
dielectric breakdown as a
result of the Electric Strengh
Test applied per Table 5.2,
following the test.
There was no visible pitting
of the contacts. The unit
functioned normally after
the test. There was no
indication of carbon tracking
that reduced spacings.
There was no indication of
dielectric breakdown as a
result of the Electric Strengh
Test applied per Table 5.2,
following the test.
supplementary information:
Results Key: IP = Internal protection operated (component indicated) CT = Constant temperatures were
obtained TW = Transformer winding opened CD = Components damaged (damaged components indicated)
NB = No indication of dielectric breakdown YB = Dielectric breakdown (time and location indicated) NC =
Cheesecloth remained intact YC = Cheesecloth charred or flamed NT = Tissue paper remained intact YT =
Tissue paper charred or flamed
TRF No.: IEC60950__1B
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 1 of 27
Report Reference #
Enclosure
National Differences
Argentina*
Australia / New Zealand
Austria**
Belgium**
China*
Czech Republic**
Denmark
Finland
France**
Germany
Greece**
Group
Hungary*
India*
Ireland*
Israel*
Italy*
Japan*
Kenya*
Korea
Malaysia*
Netherlands**
Norway
Poland*
Portugal*
Singapore*
Slovakia**
Slovenia*
Spain*
Sweden
Switzerland**
USA / Canada
United Kingdom
* No National Differences Declared
** Only Group Differences
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 2 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
Australia / New Zealand - Differences to IEC 60950-1:2001, First Edition
1.2.12.11
POTENTIAL IGNITION SOURCE
Possible fault which can starts a fire if the opencircuit voltage measured across an interruption or
faulty contact exceeds a value of 50 V (peak) a.c.
or d.c. and the product of the peak value of this
voltage and the measured r.m.s. current under
normal operating conditions exceeds 15VA.
Such a faulty contact or interruption in an electrical
connection includes those which may occur in
conductive patterns on printed boards.
Note 201: An electronic protection circuit may be
used to prevent such a fault from becoming a
POTENTIAL IGNITION SOURCE.
Pass
1.5.1
Add to the first paragraph: "or the relevant
Australian / New Zealand Standard".
Pass
1.5.2
Add to the first and third dashed items after the
words "IEC Component Standard": "or the relevant
Australian / New Zealand Standard".
Pass
1.6.1
Add: AC power distribution systems classified as
TT or IT are not allowed
Pass
1.7.12
Add to the first paragraph: All safety instructions
and safety markings shall be in English.
Pass
3.2.5
Reference Enclosures,
Substitute for Table 3B: Sizes of Conductors
-------------------------------------------------------------------- Miscellaneous, Manufacturer's
Letter of Assurance.
Rated
Nominal
Current of
cross-sectional
Equipment
area
(A)
(mm²)
-------------------------------------------------------------------0.2 <= 3
0.5*
3 <= 7.5
0.75
7.5 <= 10
(0.75) 1.00
10 <= 16
(1,0) 1.5
16 <= 25
2.5
25 <= 32
4
32 <= 40
6
40 <= 63
10
63 <= 80
16
80 <= 100
25
100 <= 125
35
125 <= 160
50
160 <= 190
70
190 <= 230
95
230 &lt;= 260
120
Pass
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 3 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
260 <= 300
150
300 <= 340
185
340 <= 400
240
400 <= 460
300
-------------------------------------------------------------------* This nominal cross-sectional area is only allowed
for Class II appliances if the length of the power
supply cord, measured between the point where
the cord or cord guard, enters the appliance, and
the entry to the plug, does not exceed 2 m (0.5
mm² three-core supply flexible cords are not
permitted; see Note 2 to Table 2.17 of AS/NZS
3191).
4.3.6
Replace the third paragraph: Equipment with a
plug portion, suitable for insertion into a 10 A 3-pin
flat-pin socket-outlet complying with AS/NZS 3112,
shall comply with the requirements in AS/NZS 3112
for equipment with integral pins for insertion into
socket-outlets.
N/A
4.3.13
For the purpose of this standard compliance with
AS/NZS 2211.1 is deemed to be compliance with
IEC60825.1
N/A
4.7
Add after the clause: For alternative resistance to
fire tests, refer to Annex YY.
Pass
6.2.1
Replace item c) with: An SELV circuit, a TNV-2
circuit or a Limited Current Circuit provided for
connection of other equipment. The requirement
for separation applies whether or not this circuit is
accessible.
N/A
6.2.2
Replace the first paragraph by: In Australia (not in
New Zealand), compliance with 6.2.2 is checked by
the tests of both 6.2.2.1 and 6.2.2.2.
N/A
6.2.2.1
Replace 6.2.2.1 with: In Australia (not in New
Zealand), the electrical separation is subjected to
10 impulses of alternating polarity, using the
impulse test generator of Annex N for 10/700µs
impulses. The interval between successive
impulses is 60 s and the initial voltage, Uc is:
N/A
- for 6.2.1a):
7.0 kV for hand-held telephones
and for headsets;
2.5 kV for other equipment;
for 6.2.1b) and
6.2.1c):
1.5 kV.
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 4 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
NOTE 1 - The 7 kV impulse is to simulate lightning
surges on typical rural and semi-rural network
lines.
NOTE 2 - The value of 2.5 kV for 6.2.1a) was
chosen to ensure adequacy of the insulation
concerned and does not necessarily simulate likely
overvoltages.
6.2.2.2
Replace the first and second paragraphs of 6.2.2.2
with: In Australia (not New Zealand), the electrical
separation is subjected to an electric strength test
according to 5.2.2.
The a.c. test voltage is:
- for 6.2.1a)
- for 6.2.1b) and 6.2.1c)
3 kV
1.5 kV
NOTE 1 - Where there are capacitors across the
insulation under test, it is recommended that d.c.
test voltages are used.
NOTE 2 - The 3 kV and 1.5 kV values have been
determined considering the low frequency induced
voltages from the power supply distribution system.
Underwriters Laboratories Inc.
N/A
Issue Date:
2009-06-16
Page 5 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
Denmark - Differences to IEC 60950-1:2001, First Edition
1.2.4.1
Certain types of Class I appliances (see sub-clause
3.2.1.1) may be provided with plug not establishing
earthing continuity when inserted into Danish
socket-outlets.
N/A
1.7.2
Supply cords of Class I equipment, which is
delivered without a plug, must be provided with a
visible tag with the following text:
N/A
"Vigtigt !
Lederen med grøn/gul isolation må kun
tilsluttes en klemme mærket
(IEC 417, No. 5019) eller (IEC 417, No. 5017)."
If essential for the safety of the equipment, the tag
must in addition be provided with a diagram, which
shows the connection of the other conductors, or
be provided with the following text:
"For tilslutning af de øvrige ledere, se medfølgende
installationsvejledning".
1.7.5
Socket-outlets for providing power to other
equipment shall be in accordance with the Heavy
Current Regulations, Section 107-2-D1, Standard
Sheet DK 1-3a, DK 1-5a or DK 1-7a, when used on
Class I equipment. For stationary equipment, the
socket0outlet shall be in accordance with Standard
Sheet DK 1-1b or DK 1-5a.
N/A
1.7.5
Class II equipment shall not be fitted with socketoutlets for providing power to other equipment.
N/A
3.2.1.1
Supply cord of single-phase equipment having a
Reference Enclosures,
rated current not exceeding 13 A shall be provided Miscellaneous, Manufacturer's
with a plug according to the Heavy Current
Letter of Assurance.
Regulations, Section 107-2-D1.
Pass
Class I equipment provided with socket-outlets with
earth contact or which are intended to be used in
locations where protection against indirect contact
is required according to the wiring rules shall be
provided with a plug in accordance with standard
sheet DK 2-1a or DK 2-5a.
If poly-phase equipment and single-phase
equipment having a rated current exceeding 13 A
is provided with a supply cord with a plug, this plug
shall be in accordance with the Heavy Current
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 6 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Regulations, Section 107-2-D1 or EN 60309-2.
Underwriters Laboratories Inc.
Verdict
Issue Date:
2009-06-16
Page 7 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
Finland - Differences to IEC 60950-1:2001, First Edition
1.7.2
Class I Pluggable Equipment Type A intended for Reference Enclosures,
connection to other equipment or a network shall, if Miscellaneous, Manufacturer's
safety relies on connection to protective earth or if Letter of Assurance.
surge suppressors are connected between the
network terminals and accessible parts, have a
marking stating that the equipment must be
connected to an earthed mains socket-outlet. The
marking text shall be:
"Laite on liitettävä suojamaadoituskoskettimilla
varustettuun pistorasiaan"
Pass
6.1.2.1
Add the following text between the first and second
paragraph:
N/A
If this insulation is solid, including insulation
forming part of a component, it shall at least consist
of either
- two layers of thin sheet material, each of which
shall pass the electric strength test below, or
- one layer having a distance through insulation of
at least 0.4 mm, which shall pass the electric
strength test below.
If this insulation forms part of a semiconductor
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that clearances and
creepage distances do not exist, if the component
passes the electric strength test in accordance with
the compliance clause below and in addition:
- passes the tests and inspection criteria of IEC
60950-1, 2.10.8 with an electric strength test of 1.5
kV multiplied by 1.6 (the electric strength test of
2.10.7 shall be performed using 1.5 kV), and
- is subject to routing testing for electric strength
during manufacturing, using a test voltage of 1.5
kV.
It is permitted to bridge this insulation with a
capacitor complying with IEC 60384-14:1993,
subclass Y2.
A capacitor classified Y3 according to IEC 6038414:1993, may bridge this insulation under the
following conditions:
- the insulation requirements are satisfied by
having a capacitor classified Y3 as defined by IEC
60384-14, which in addition to the Y3 testing, is
tested with an impulse test of 2,5 kV defined in EN
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 8 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
60950-1, subclause 6.2.2.1;
- the additional testing shall be performed on all the
test specimens as described in IEC 60384-14;
- the impulse test of 2,5 kV is to be performed
before the endurance test in IEC 60384-14, in the
sequence of tests as described in IEC 60384-14.
6.1.2.2
The exclusions are applicable for permanently
connected equipment and pluggable equipment
type B and equipment intended to be used in a
restricted access location where equipotential
bonding has been applied, e.g. in a
telecommunication centre, and which has provision
for a permanently connected protective earthing
conductor and is provided with instructions for the
installation of that conductor by a service person.
N/A
7.1
Requirements according to this annex, 6.1.2.1 and
6.1.2.2 apply with the term telecommunication
network in 6.1.2 being replaced by the term cable
distribution system.
N/A
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 9 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
Germany - Differences to IEC 60950-1:2001, First Edition
1.7.12
H
(Gesetz uber technische Arbeitsmittel
(Garatesicherheitsgesetz) [Law of technical labour
equipment {Equipment safety law}], of 23rd
October 1992, Article 3, 3rd paragraph, 2nd
sentence, together with the "Allgemeine
Verwaltungsvorschrift zur Durchfuhrung des
Zweiten Abschritts des Geratesicherheitsgesetzes"
[General administrative regulation on the execution
of the Second Section of the Equipment safety
law], of 10th January 1996, article 2, the
paragraph, item 2).
Directions for use with rules to prevent certain
hazards for (among others) maintenance of the
technical labour equipment, also for imported
technical labour equipment shall be written in the
German language.
NOTE: Of this requirement, rules for use even only
by service personnel are not exempted.
Reviewed only English
markings/instructions.
Pass
May be provided in other
languages upon request from
the manufacturer.
Reference Enclosures,
Miscellaneous, for
manufacturer's letter of
declaration.
(Regulation on protection against hazards by Xray,of 8th January 1987, Article 5 [operation of Xray emission source], clauses 1 to 4)
a) A licence is required by those who operate an
X-ray emission source.
b) A licence in accordance with Cl. 1 is not
required by those who operate an X-ray emission
source on which the electron acceleration voltage
does not exceed 20 kV if
1) the local dose rate at a distance of 0,1 m from
the surface does not exceed 1 µSv/h and
2) it is adequately indicated on the X-ray emission
source that
i) X-rays are generated
ii) the electron acceleration voltage must not
exceed the maximum value stipulated by the
manufacturer or importer.
c) A licence in accordance with Cl. 1 is also not
required by persons who operate an X-ray
emission source on which the electron acceleration
voltage exceeds 20 kV if
1) the X-ray emission source has been granted a
type approval and
2) it is adequately indicated on the X-ray emission
source that
i) X-rays are generated
ii) the device stipulated by the manufacturer or
importer guarantees that the maximum
Underwriters Laboratories Inc.
N/A
Issue Date:
2009-06-16
Page 10 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
permissible local dose rate in accordance with the
type approval is not exceeded and
iii) the electron acceleration voltage must not
exceed the maximum value stipulated by the
manufacturer or importer.
d) Furthermore, a licence in accordance with Cl. 1
is also not required by persons who operate X-ray
emission sources on which the electron
acceleration voltage does not exceed 30 kV if
1) the X-rays are generated only by intrinsically
safe CRTs complying with Enclosure III, No. 6,
2) the values stipulated in accordance with
Enclosure III, No. 6.2 are limited by technical
measures and specified in the device and
3) it is adequately indicated on the X-ray emission
source that the X-rays generated are adequately
screened by the intrinsically safe CRT.
Underwriters Laboratories Inc.
Verdict
Issue Date:
2009-06-16
Page 11 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
Group - Differences to IEC 60950-1:2001, First Edition
2.7.1
Equipment is Pluggable Type
Replace the subclause as follows:
A.
Basic requirements
To protect against excessive current, short-circuits
and earth faults in primary circuits, protective
devices shall be included either as integral parts of
the equipment or as parts of the building
installation, subject to the following, a), b) and c):
a) except as detailed in b) and c), protective
devices necessary to comply with the requirements
of 5.3 shall be included as parts of the equipment;
b) for components in series with the mains input to
the equipment such as the supply cord, appliance
coupler, r.f.i. filter and switch, short-circuit and
earth fault protection may be provided by protective
devices in the building installation;
c) it is permitted for pluggable equipment type B or
permanently connected equipment, to rely on
dedicated overcurrent and short-circuit protection in
the building installation, provided that the means of
protection, e.g. fuses or circuit breakers, is fully
specified in the installation instructions.
If reliance is placed on protection in the building
installation, the installation instructions shall so
state, except that for pluggable equipment type A
the building installation shall be regarded as
providing protection in accordance with the rating
of the wall socket outlet.
Pass
2.7.2
Void
N/A
2.10.2
Replace the first line "(see also 1.4.7)" by "(see
also 1.4.8)".
Pass
3.2.3
Delete NOTE 1, and in table 3A delete the conduit
sizes in parentheses.
Pass
3.2.5
Replace:
"60245 IEC 53" by "H05 RR-F"
"60227 IEC 52" by "H03 VV-F or H03 VVH2-F"
"60227 IEC 53" by "H05 VV-F or H05 VVH2-F"
Reference Enclosures,
Miscellaneous, Manufacturer's
Letter of Assurance.
In table 3B, replace the first four lines by the
following:
Up to and including 6
0.75 ¹
Over 6 up to and including 10 0.75 ² 1.0
Over 10 up to and including 16 1.0 ³
1.5
In the Conditions applicable to table 3B, delete the
Underwriters Laboratories Inc.
Pass
Issue Date:
2009-06-16
Page 12 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
words "in some countries" in condition ¹.
In Note 1, delete the second sentence.
3.3.4
In table 3D, delete the fourth line: conductor sizes
for 10 to 13 A, and replace with the following:
"Over 10 up to and
including 16
1.5 to 2.5 1.5 to by 4"
N/A
Delete the fifth line: conductor sizes for 13 to 16A.
4.3.13.6
Add the following note:
NOTE - Attention is drawn to 1999/519/EC: Council
Recommendation on the limitation of exposure of
the general public to electromagnetic fields 0 Hz to
300 GHz. Standards taking into account this
recommendation are currently under development.
Pass
General
Delete all the "country" notes in the reference
document according to the following list:
1.5.1
Note 2
1.5.8 Note 2
1.6.1
Note
1.7.2 Note 4
1.7.12 Note 2
2.1
Note
2.2.3
Note
2.2.4 Note
2.3.2
Note 2, 7, 8
2.3.3 Note 1, 2
2.3.4
Note 2,3
2.7.1 Note
2.10.3.1 Note 4
3.2.1.1 Note
3.2.3
Note 1, 2
3.2.5.1 Note 2
4.3.6
Note 1,2
4.7.2.2 Note
4.7.3.1 Note 2
6.1.2.1 Note
6.1.2.2 Note
6.2.2 Note
6.2.2.1 Note 2
6.2.2.2 Note
7
Note 4
7.1
Note
G2.1
Note 1, 2
H
Note 2
Pass
H
Replace the last paragraph of this annex by:
At any point 10 cm from the surface of the operator
access area, the dose rate shall not exceed 1
µSv/h (0,1 mR/h) (see note). Account is taken of
the background level.
Replace the notes as follows:
NOTE - These values appear in Directive
96/29/Euratom.
Delete Note 2.
N/A
P
Replace the text of this annex by: See annex ZA
Pass
Q
Replace the title of IEC 61032 by "Protection of
persons and equipment by enclosures - Probes for
verification".
Add the following notes for the standards indicated:
IEC 60127
NOTE Harmonized as EN 60127
Pass
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 13 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
(Series) (not modified)
IEC 60269-2-1 NOTE Harmonized as HD
630.2.1 S4:2000 (modified)
IEC 60529
NOTE Harmonized as EN
60529:1991 (not modified)
IEC 61032
NOTE Harmonized as EN
61032:1998 (not modified)
IEC 61140
NOTE Harmonized as EN
61140:2001 (not modified)
ITU-T Recommendation K.31
NOTE in Europe, the suggested document is EN
50083-1.
Korea - Differences to IEC 60950-1:2001, First Edition
1.5.101
Addition: Plugs for the connection of the apparatus Reference Enclosures,
to the supply mains comply with the Korean
Miscellaneous, Manufacturer's
requirement (KSC 8305).
Letter of Assurance.
Pass
7
Addition: EMC - The apparatus shall complies with Reference Enclosures,
the relevant CISPR standards.
Miscellaneous, Manufacturer's
Letter of Declaration.
Pass
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 14 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
Norway - Differences to IEC 60950-1:2001, First Edition
1.5.8
Due to the IT power system used (see annex V,
figure V.7), capacitors are required to be rated for
the applicable phase-to-phase voltage (230 V).
Line-to-earth capacitors are
located within the separately
certified power supply and are
correctly rated for the phase to
phase system voltage.
Pass
1.7.2
Class I Pluggable Equipment Type A intended for Reference Enclosures,
connection to other equipment or a network shall, if Miscellaneous, Manufacturer's
safety relies on connection to protective earth or if Letter of Assurance.
surge suppressors are connected between the
network terminals and accessible parts, have a
marking stating that the equipment must be
connected to an earthed mains socket-outlet. The
marking text shall be:
"Apparatet må tilkoples jordet stikkontakt"
Pass
2.2.4
Requirements according to this annex, 1.7.2 and
6.1.2.1 apply.
N/A
2.3.2
Requirements according to this annex, 6.1.2.1
apply.
N/A
2.3.3
Requirements according to this annex, 1.7.2 and
6.1.2.1 apply.
N/A
2.3.4
Requirements according to this annex, 1.7.2 and
6.1.2.1 apply.
N/A
2.10.3.1
Due to the IT power distribution system used (see
annex V, figure V.7), the A.C. mains supply voltage
is considered to be equal to the line-to-line voltage,
and will remain at 230 V in case of a single earth
fault.
Pass
6.1.2.1
Add the following text between the first and second
paragraph:
N/A
If this insulation is solid, including insulation
forming part of a component, it shall at least consist
of either
- two layers of thin sheet material, each of which
shall pass the electric strength test below, or
- one layer having a distance through insulation of
at least 0.4 mm, which shall pass the electric
strength test below.
If this insulation forms part of a semiconductor
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that clearances and
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 15 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
creepage distances do not exist, if the component
passes the electric strength test in accordance with
the compliance clause below and in addition:
- passes the tests and inspection criteria of IEC
60950-1, 2.10.8 with an electric strength test of 1.5
kV multiplied by 1.6 (the electric strength test of
2.10.7 shall be performed using 1.5 kV), and
- is subject to routing testing for electric strength
during manufacturing, using a test voltage of 1.5
kV.
It is permitted to bridge this insulation with a
capacitor complying with IEC 60384-14:1993,
subclass Y2.
A capacitor classified Y3 according to IEC 6038414:1993, may bridge this insulation under the
following conditions:
- the insulation requirements are satisfied by
having a capacitor classified Y3 as defined by IEC
60384-14, which in addition to the Y3 testing, is
tested with an impulse test of 2,5 kV defined in EN
60950-1, subclause 6.2.2.1;
- the additional testing shall be performed on all the
test specimens as described in IEC 60384-14;
- the impulse test of 2,5 kV is to be performed
before the endurance test in IEC 60384-14, in the
sequence of tests as described in IEC 60384-14.
6.1.2.2
The exclusions are applicable for permanently
connected equipment and pluggable equipment
type B and equipment intended to be used in a
restricted access location where equipotential
bonding has been applied, e.g. in a
telecommunication centre, and which has provision
for a permanently connected protective earthing
conductor and is provided with instructions for the
installation of that conductor by a service person.
N/A
7.1
Requirements according to this annex, 6.1.2.1 and
6.1.2.2 apply with the term telecommunication
network in 6.1.2 being replaced by the term cable
distribution system.
N/A
G.2.1
Due to the IT power distribution system used (see
annex V, figure V.7), the A.C. mains supply voltage
is considered to be equal to the line-to-line voltage,
and will remain at 230 V in case of a single earth
fault.
N/A
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 16 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
Sweden - Differences to IEC 60950-1:2001, First Edition
1.5.1
(Ordinance (1990:944)) Add NOTE: Switches
containing mercury such as thermostats, relays
and level controllers are not allowed.
N/A
1.7.2
Class I Pluggable Equipment Type A intended for Reference Enclosures,
connection to other equipment or a network shall, if Miscellaneous, Manufacturer's
safety relies on connection to protective earth or if Letter of Assurance.
surge suppressors are connected between the
network terminals and accessible parts, have a
marking stating that the equipment must be
connected to an earthed mains socket-outlet. The
marking text shall be:
"Apparaten skall anslutas till jordat uttag"
Pass
6.1.2.1
Add the following text between the first and second
paragraph:
N/A
If this insulation is solid, including insulation
forming part of a component, it shall at least consist
of either
- two layers of thin sheet material, each of which
shall pass the electric strength test below, or
- one layer having a distance through insulation of
at least 0.4 mm, which shall pass the electric
strength test below.
If this insulation forms part of a semiconductor
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that clearances and
creepage distances do not exist, if the component
passes the electric strength test in accordance with
the compliance clause below and in addition:
- passes the tests and inspection criteria of IEC
60950-1, 2.10.8 with an electric strength test of 1.5
kV multiplied by 1.6 (the electric strength test of
2.10.7 shall be performed using 1.5 kV), and
- is subject to routing testing for electric strength
during manufacturing, using a test voltage of 1.5
kV.
It is permitted to bridge this insulation with a
capacitor complying with IEC 60384-14:1993,
subclass Y2.
A capacitor classified Y3 according to IEC 6038414:1993, may bridge this insulation under the
following conditions:
- the insulation requirements are satisfied by
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 17 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
having a capacitor classified Y3 as defined by IEC
60384-14, which in addition to the Y3 testing, is
tested with an impulse test of 2,5 kV defined in EN
60950-1, subclause 6.2.2.1;
- the additional testing shall be performed on all the
test specimens as described in IEC 60384-14;
- the impulse test of 2,5 kV is to be performed
before the endurance test in IEC 60384-14, in the
sequence of tests as described in IEC 60384-14.
6.1.2.2
The exclusions are applicable for permanently
connected equipment and pluggable equipment
type B and equipment intended to be used in a
restricted access location where equipotential
bonding has been applied, e.g. in a
telecommunication centre, and which has provision
for a permanently connected protective earthing
conductor and is provided with instructions for the
installation of that conductor by a service person.
N/A
7.1
Requirements according to this annex, 6.1.2.1 and
6.1.2.2 apply with the term telecommunication
network in 6.1.2 being replaced by the term cable
distribution system.
N/A
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 18 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
USA / Canada - Differences to IEC 60950-1:2001, First Edition
1.1
Equipment able to be installed in accordance with
the National Electrical Code ANSI/NFPA 70 and
the Canadian Electrical Code, Part1, and when
applicable, the National Electrical Safety Code,
IEEE C2.
Pass
1.1.1
Equipment able to be installed in accordance with
ANSI/NFPA 75 and NEC Art. 645 unless intended
for use outside of computer room and provided with
such instructions.
Pass
1.1.2
Equipment in wire-line communication facilities
serving high-voltage electric power stations
operating at greater than 1kV are excluded.
N/A
1.1.2
Special requirements apply to equipment intended
for use outdoors.
N/A
1.4.14
For Pluggable Equipment Type A, the protection in
the installation is assumed to be 20 A.
Pass
1.5.1
All IEC standards for components identified in
Annex P.1 replaced by the relevant requirements of
CSA and UL component standards in Annex P.1.
Pass
1.5.1
All IEC standards for components identified in
Annex P.2 alternatively satisfied by the relevant
requirements of CSA and UL component standards
in Annex P.2.
Pass
1.5.5
Interconnecting cables acceptable for the
application regarding voltage, current, temperature,
flammability, mechanical serviceability and the like.
N/A
1.5.5
For other than limited power and TNV circuits, the
type of output circuit identified for output connector.
N/A
1.5.5
External cable assemblies that exceed 3.05 m in
length to be types specified in the NEC and CEC.
N/A
1.5.5
Detachable external interconnecting cables 3.05 m Interconnecting cables not
or less in length and provided with equipment
provided.
marked to identify the responsible organization and
the designation for the cable.
N/A
1.5.5
Building wiring and cable for use in ducts, plenums
and other air handling space subject to special
requirements and excluded from scope.
N/A
1.5.5
Telephone line and extension cords and the like
comply with UL 1863 and CSA C22.2 No. 233.
N/A
1.6.1.2
Equipment intended for connection to a d.c. power
(mains) distribution system is subject to special
N/A
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 19 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
circuit classification requirements (e.g., TNV-2)
1.6.1.2
Earthing of d.c. powered equipment provided.
N/A
1.7
Lamp replacement information indicated on
lampholder in operator access area.
N/A
1.7.1
Special marking format for equipment intended for
use on a supply system with an earthed neutral
and more than one phase conductor.
N/A
1.7.1
Equipment voltage rating not higher than rating of
the plug except under special conditions.
Pass
1.7.6
Special fuse replacement marking for operator
accessible fuses.
N/A
1.7.7
Identification of terminal connection of the
equipment earthing conductor.
1.7.7
Connectors and field wiring terminals for external
Class 2 or Class 3 circuits provided with marking
indicating minimum Class of wiring to be used.
N/A
1.7.7
Marking located adjacent to terminals and visible
during wiring.
N/A
2.1.1
Screw shell of Edison-base lampholder tied to the
neutral conductor.
N/A
2.1.1.1
Bare TNV conductive parts in the interior of
equipment normally protected against contact by a
cover intended for occasional removal are exempt
provided instructions include directions for
disconnection of TNV prior to removal of the cover.
N/A
2.3.1.b
Other telecommunication signaling systems (e.g.,
message waiting) than described in 2.3.1(b) are
subject to M.4.
N/A
2.3.1.b
For TNV-2 and TNV-3 circuits with other than
ringing signals and with voltages exceeding 42.4
Vp or 60 V d.c., the maximum current limit through
a 2000 Ohm or greater resistor with loads
disconnected is 7.1 mA peak or 30 mA d.c. under
normal conditions.
N/A
2.3.1.b
Limits for measurements across 5000 ohm resistor
in the event of a single fault are replaced after 200
ms with the limits of M.3.1.4.
N/A
2.3.2
Enamel coating on signal transformer winding wire
allowed as an alternative to Basic insulation in
specific telecommunication applications when
subjected to special construction requirements and
routine testing.
N/A
Equipment employs an
appliance inlet.
Underwriters Laboratories Inc.
N/A
Issue Date:
2009-06-16
Page 20 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
2.3.2
In the event of a single fault, the limits of 2.2.3
apply to SELV circuits and accessible conductive
parts.
N/A
2.5
Overcurrent protection device required for Class 2
and Class 3 limiting in accordance with the NEC, or
for a Limited Power Source, not interchangeable
with devices of higher ratings if operator
replaceable.
N/A
2.6
Equipment having receptacles for output a.c. power
connectors generated from an internal separately
derived source have the earthed (grounded) circuit
conductor suitably bonded to earth.
N/A
2.6.3.3
For Pluggable Equipment Type A, if neither a) or b) Evaluated in separate
are applicable, the current rating of the circuit is
certification of power supply.
taken as 20 A.
N/A
2.6.3.4
Capacity of connection between earthing terminal
and parts required to be earthed subject to special
conditions based on the current rating of the circuit.
N/A
2.6.3.4
Protective bonding conductors and their terminals
of non-standard constructions (e.g. PWB traces)
evaluated to limited short-circuit test of CSA C22.2
No.0.4.
N/A
2.6.4.1
Field wiring terminals for earthing conductors
suitable for wire sizes (gauge) used in US and
Canada.
N/A
2.7.1
Data for selection of special external branch circuit
overcurrent devices marked on the equipment.
N/A
2.7.1
Standard supply outlets protected by overcurrent
device in accordance with the NEC, and CEC, Part
1.
N/A
2.7.1
Overcurrent protection for individual transformers
that distribute power to other units over branch
circuit wiring.
N/A
2.7.1
Additional requirements for overcurrent protection
apply to equipment provided with panelboards.
N/A
2.7.1
Non-motor-operated equipment requiring special
overcurrent protective device marked with device
rating.
N/A
2.10.5.4
Multi-layer winding wire subject to UL component
wire requirements in addition to 2.10.5.4 and
Annex U.
N/A
3.1.1
Permissible combinations of internal wiring/external
Pass
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 21 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
cable sizes for overcurrent and short circuit
protection.
3.1.1
All interconnecting cables protected against
overcurrent and short circuit.
Interconnecting Cables not
provided. Power pins of the
I/O connector ports are
protected by PTCs. Reference
Table 1.5.1.
3.2
Wiring methods permit connection of equipment to
primary power supply in accordance with the NEC
and CEC, Part 1.
Pass
3.2.1
Permitted use for flexible cords and plugs.
Pass
3.2.1
Flexible cords provided with attachment plug rated
125% of equipment current rating.
Pass
3.2.1
Any Class II equipment provided with 15 or 20 A
standard supply outlets, Edison-base lampholders
or single pole disconnect device provided with a
polarized type attachment plug.
N/A
3.2.1.2
Equipment intended for connection to DC mains
supply power systems complies with special wiring
requirements (e.g., no permanent connection to
supply by flexible cord).
N/A
3.2.1.2
Equipment with one pole of the DC mains supply
connected to both the equipment mains input
terminal and the main protective earthing terminal
provided with special instructions and construction
provisions for earthing
N/A
3.2.1.2
Equipment with means for connecting supply to
earthing electrode conductor has no switches or
protective devices between supply connection and
earthing electrode connection.
N/A
3.2.1.2
Special markings and instructions for equipment
with provisions to connect earthed conductor of a
DC supply circuit to earthing conductor at the
equipment.
N/A
3.2.1.2
Special markings and instructions for equipment
with earthed conductor of a DC supply circuit
connected to the earthing conductor at the
equipment.
N/A
3.2.1.2
Terminals and leads provided for permanent
connection of DC powered equipment to supply
marked to indicate polarity if reverse polarity may
result in a hazard.
N/A
Underwriters Laboratories Inc.
N/A
Issue Date:
2009-06-16
Page 22 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
3.2.3
Permanently connected equipment has provision
for connecting and securing a field wiring system
(i.e. conduit, or leads etc.) per the NEC and CEC,
Part 1.
N/A
3.2.3
Permanently connected equipment may have
terminals or leads not smaller than No. 18 AWG
(0.82 mm²) and not less than 152 mm in length for
connection of field installed wiring.
N/A
3.2.3
If supply wires exceed 60 °C, marking indicates
use of 75 °C or 90 °C wiring for supply connection
as appropriate.
N/A
3.2.3
Equipment compatible with suitable trade sizes of
conduits and cables.
N/A
3.2.5
Length of power supply cord limited to between 1.5 Power cord for North America
and 4.5 m unless shorter length used when
is optional. If it is provided, the
intended for a special installation.
applicant specifies length of
power cord is between 1.5m
and 4.5m.
Pass
3.2.5
Conductors in power supply cords sized according
to NEC and CEC, Part I.
Pass
3.2.5
Power supply cords and cord sets incorporate
flexible cords suitable for the particular application.
Pass
3.2.6
Strain relief provided for non-detachable
interconnecting cables not supplied by a limited
power source.
N/A
3.2.9
Adequate wire bending space and volume of field
wiring compartment required to properly make the
field connections.
N/A
3.2.9
Equipment intended solely for installation in
Restricted Access Locations using low voltage d.c.
systems may not need provision for connecting and
securing a field wiring system. A method of
securing wiring or instructions provided to ensure
the wiring is protected from abuse.
N/A
3.3
Field wiring terminals provided for interconnection
of units for other then LPS or Class 2 circuits also
comply with 3.3.
N/A
3.3
Interconnection of units by LPS or Class 2
conductors may have field wiring connectors other
than those specified in 3.3 if wiring is reliably
separated.
N/A
3.3.1
Terminals for the connection of neutral conductor
identified by a distinctive white marking or other
N/A
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 23 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
equally effective means.
3.3.3
Wire binding screw terminal permitted for
connection of No. 10 AWG (5.3 mm²) or smaller
conductor if provided with upturned lugs, cupped
washer or equivalent retention.
N/A
3.3.4
Terminals accept wire sizes (gauge) used in the
U.S. and Canada.
N/A
3.3.4
Terminals accept current-carrying conductors rated
125% of the equipment current rating.
N/A
3.3.6
Field wiring terminals marked to indicate the
material(s) of the conductor appropriate for the
terminals used.
N/A
3.3.6
Connection of an aluminum conductor not
permitted to terminal for equipment earthing
conductor.
N/A
3.3.6
Field wiring connections made through the use of
suitable pressure connectors (including set screw
type), solder lugs or splices to flexible leads.
N/A
3.4.2
Separate motor control device(s) required for cordconnected equipment rated more than 12 A, or with
motor rated more than 1/3 hp or more than 120 V.
N/A
3.4.8
Vertically mounted disconnect devices oriented so
up position of handle is "on".
N/A
3.4.11
For computer-room applications, equipment with
battery systems capable of supplying 750 VA for 5
min require battery disconnect means.
N/A
4.2.8.1
Special opening restrictions for enclosures around
CRTs with face dimension of 160 mm or more.
N/A
4.2.9
Compartment housing high-pressure lamp marked
to indicate risk of explosion.
N/A
4.3.2
Loading test for equipment with handle(s) used to
support more than 9 kg tested at four times the
weight of the unit.
N/A
4.3.6
In addition to the IEC requirements, Direct Plug-in
Equipment complies with UL 1310 or CSA 223
mechanical assembly requirements.
N/A
4.3.12
The maximum quantity of flammable liquid stored
in equipment complies with ANSI/NFPA 30(Table
NAE.6).
N/A
4.3.12
Equipment using replenishable liquids marked to
indicate type of liquid to be used.
N/A
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 24 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
4.3.13.2
Equipment that produces x-radiation and does not
comply with 4.3.12 under all conditions of servicing
marked to indicate the presence of radiation where
readily visible.
N/A
4.3.13.5
Requirements contained in the applicable national
codes and regulations apply to lasers (21 CFR
1040 and REDR C1370).
Pass
4.7
Automated information storage equipment intended
to contain more than 0.76 m³ of combustible media
requires provision for automatic sprinklers or a
gaseous agent extinguishing system.
N/A
4.7.3.1
Equipment for use in environmental air space other
than ducts or plenums provided with metal
enclosure or with non-metallic enclosure having
adequate fire-resistance and low smoke producing
characteristics. Low smoke-producing
characteristics evaluated according to UL 2043.
Equipment for installation in space used for
environmental air as described in Sec. 300-22(c) of
the NEC provided with instructions indicating
suitability for installation in such locations.
N/A
4.7.3.1
Flame spread rating for external surface of
combustible material with exposed area greater
than 0.93 m² or a single dimension greater than 1.8
m; 50 or less for computer room applications or
200 or less for other applications.
N/A
4.7.3.4
Wire marked "VW-1" or "FT-1" considered
equivalent.
Pass
5.1.8.2
Special earthing provisions and instructions for
equipment with high touch current due to
telecommunication network connections.
N/A
5.1.8.3
Touch current due to ringing voltage for equipment
containing telecommunication network leads.
N/A
5.3.6
Overloading of SELV connectors and printed wiring Data pins of the RJ-45
board receptacles accessible to the operator.
ethernet connectors, the USB
connectors, the RS232, VGA,
Keyboard and Mouse
connectors are Limited Power
Source by impedance of the
logic circuits.
N/A
Power pins of the Keyboard,
Mouse, USB and VGA
connectors are Limited Power
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 25 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
Source by impedance of the
PTC devices. Reference
Table 1.5.1
5.3.6
Tests interrupted by opening of a component
repeated two additional times.
N/A
5.3.8.1
Test interrupted by opening of wire or trace subject
to certain conditions.
N/A
6
Specialized instructions provided for telephones
that may be connected to a telecommunications
network.
6
Marking identifying function of telecommunication
type connectors not used for connection to a
telecommunication network.
N/A
6.2.1
Special requirements for enameled wiring used as
electrical separation provided between parts
connected to telecommunication network and
telecommunication circuitry intentionally isolated
from network.
N/A
6.2.1
Digital line termination equipment (e.g., NCTE)
subject to separation requirements.
N/A
6.3
Equipment remotely powered over
telecommunication wiring systems provided with
specialized markings adjacent to the connection.
N/A
6.3
Overcurrent protection incorporated into equipment
to provide power over telecommunication wiring
system not interchangeable with devices of higher
ratings if operator replaceable.
N/A
6.4
Additional requirements for equipment intended for
connection to a telecommunication network using
cable subject to overvoltage from power line
failures (Fig. 6C).
N/A
6.4
Where 26 AWG line cord required by Fig. 6C,
either the cord is provided with the equipment or
described in the safety instructions.
N/A
6.5
Acoustic pressure from an ear piece less than 136
dBA for short duration disturbances, and less than
125 dBA for handsets, 118 dBA for headsets, and
121 dBA for insert earphones, for long duration
disturbances.
N/A
7
Equipment associated with the cable distribution
system may need to be subjected to applicable
parts of Chapter 8 of the NEC.
N/A
Equipment does not have
connections to TNV circuits.
Underwriters Laboratories Inc.
N/A
Issue Date:
2009-06-16
Page 26 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
H
Ionizing radiation measurements made under
single fault conditions in accordance with the
requirements of the Code of Federal Regulations
21 CFR 1020 and the Canadian Radiation Emitting
Devices Act, REDR C1370.
N/A
M.2
Continuous ringing signals evaluated to Method A
subjected to special accessibility considerations.
N/A
M.4
Special requirements for message waiting and
similar telecommunications signals.
N/A
NAC
Equipment intended for use with a generic
secondary protector marked with suitable
instructions.
N/A
NAC
Equipment intended for use with a specific primary
or secondary protector marked with suitable
instructions.
N/A
NAF
Household/Home Office Document Shredders
N/A
NAF.1.7
Markings and instructions alert the user to key
safety considerations related to use of shredders,
including not intended to be used by children, avoid
touching document feed opening, avoid clothes
and hair entanglement, and avoid aerosol products.
N/A
NAF.2.8.3
Safety interlock cannot be inadvertently activated
by the articulated accessibility probe (figure
NAF.1).
N/A
NAF.3.4
Provided with an isolating switch complying with
3.4.2, including 3 mm contact gap, with appropriate
markings associated with the switch.
N/A
NAF.4.4
Hazardous moving parts are not accessible to the
user, as determined using the articulated
accessibility probe (figure NAF.1) and the
accessibility probe/wedge (figures NAF.2/NAF.3).
N/A
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 27 of 27
Report Reference #
E209323-A50-CB-1
IEC 60950-1
SubClause Difference + Test
Result - Remark
Verdict
United Kingdom - Differences to IEC 60950-1:2001, First Edition
2.6.3.3
The current rating of the circuit shall be taken as 13
A, not 16 A.
N/A
2.7.1
To protect against excessive currents and shortcircuits in the primary circuit of direct plug-in
equipment, protective device shall be included as
integral parts of the direct plug-in equipment.
N/A
3.2.1.1
Reference Enclosures,
Apparatus which is fitted with a flexible cable or
Miscellaneous, Manufacturer's
cord and is designed to be connected to a mains
Letter of Assurance.
socket conforming to BS 1363 by means of that
flexible cable or cord and plug, shall be fitted with a
"standard plug" in accordance with Statutory
Instrument 1786: 1994 - The Plugs and Sockets
etc. (Safety) Regulations 1994, unless exempted
by those regulations.
Pass
NOTE: "Standard plug" is defined in SI 1786: 1994
and essentially means an approved plug
conforming to BS 1363 or an approved conversion
plug.
3.2.5.1
A power supply cord with conductor of 1.25 mm² is Reference Enclosures,
allowed for equipment with a rated current over
Miscellaneous, Manufacturer's
10A and up to and including 13A.
Letter of Assurance.
Pass
3.3.4
The range of conductor sizes of flexible cords to be
accepted by terminals for equipment with a rated
current of over 10 A up to and including 13 A is
1.25 mm² to 1.5 mm² nominal cross-sectional area.
N/A
4.3.6
The torque test is performed using a socket outlet
complying with BS 1363 and the plug part of Direct
Plug-In Equipment shall be assessed to BS 1363:
Part 1, 12.1, 12.2, 12.3, 12.9, 12.11, 12.12, 12.16
and 12.17, except that the test of 12.17 is
performed at not less than 125 °C.
N/A
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 1 of 4
Report Reference #
Enclosure
Photographs
Supplement Id
Description
3-01
745 Front View (Represents 745-8, 745-12)
3-02
745 Inside View (Represents 745-8, 745-12)
3-03
745 Rear View (Represents 745-8, 745-12)
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 2 of 4
Report Reference #
Photographs ID 3-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 3 of 4
Report Reference #
Photographs ID 3-02
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 4 of 4
Report Reference #
Photographs ID 3-03
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 1 of 2
Report Reference #
E209323-A50-CB-1
Enclosure
Manuals
Supplement Id
6-01
Description
Representative Installation / Operation Manual page regarding installation
and maintenance. Note: Models numbers will be changed to 745-8, 745-12.
Underwriters Laboratories Inc.
Issue Date:
2009-06-16
Page 2 of 2
Report Reference #
Manuals ID 6-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 1 of 2
Report Reference #
Enclosure
Miscellaneous
Supplement Id
7-01
Description
Manufacturer's Letter of Assurance
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 2 of 2
Report Reference #
Misc ID 7-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 1 of 59
Report Reference #
Enclosure
Licenses
Supplement Id
8-01
Description
Component Licenses
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 2 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 3 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 4 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 5 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 6 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 7 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 8 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 9 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 10 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 11 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 12 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 13 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 14 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 15 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 16 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 17 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 18 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 19 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 20 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 21 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 22 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 23 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 24 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 25 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 26 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 27 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 28 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 29 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 30 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 31 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 32 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 33 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 34 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 35 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 36 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 37 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 38 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 39 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 40 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 41 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 42 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 43 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 44 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 45 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 46 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 47 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 48 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 49 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 50 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 51 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 52 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 53 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 54 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 55 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 56 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 57 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 58 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Issue Date:
2009-06-16
Page 59 of 59
Report Reference #
License ID 8-01
Underwriters Laboratories Inc.
E209323-A50-CB-1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement