SPEC - PortAllBikers

SPEC - PortAllBikers
FOREWORD
This Supplementary Service Manual has been prepared to introduce new service and data for the
FZS600 2000. For complete service information procedures it is necessary to use this Supplementary
Service Manual together with the following manual.
FZS600 SERVICE MANUAL: 5DM1-AE1
FZS600 2000
SUPPLEMENTARY
SERVICE MANUAL
1999 by Yamaha Motor Co., Ltd.
First Edition, June 1999
Any reproduction or unauthorized use
without the written permission of
Yamaha Motor Co., Ltd. is expressly
prohibited.
EB001000
NOTICE
This manual was produced by the Yamaha Motor Company primarily for use by Yamaha dealers and
their qualified mechanics. It is not possible to include all the knowledge of a mechanic in one manual,
so it is assumed that anyone who uses this book to perform maintenance and repairs on Yamaha
scooter has a basic understanding of the mechanical ideas and the procedures of scooter repair.
Repairs attempted by anyone without this knowledge are likely to render the scooter unfit for use.
Yamaha Motor Company, Ltd. is continually striving to improve all its models. Modifications and
significant changes in specifications or procedures will be forwarded to all authorized Yamaha dealers
and will appear in future editions of this manual where applicable.
NOTE:
Designs and specifications are subject to change without notice.
IMPORTANT INFORMATION
Particularly important information is distinguished in this manual by the following.
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED!
WARNING
CAUTION:
NOTE:
Failure to follow WARNING instructions could result in severe injury or death to
the motorcycle operator, a bystander or a person inspecting or repairing the
motorcycle.
A CAUTION indicates special precautions that must be taken to avoid damage
to the motorcycle.
A NOTE provides key information to make procedures easier or clearer.
YP002000
HOW TO USE THIS MANUAL
This manual is intended as a handy, easy-to-read reference book for the mechanic. Comprehensive
explanations of all installation, removal,disassembly, assembly, repair and inspection procedures are
laid out with the individual steps in sequential order.
1 The manual is divided into chapters. An abbreviation and symbol in the upper right corner of each
page indicate the current chapter. Refer to “SYMBOLS” on the following page.
2 Each chapter is divided into sections. The current section title is shown at the top of each page,
except in Chapter 3 (“Periodic Inspections and Adjustments”), where the sub-section title (-s) appear.
(In Chapter 3, “Periodic Inspections and Adjustments”, the sub-section title appears at the top of each
page, instead of the section title.)
3 Sub-section titles appear in smaller print than the section title.
4 To help identify parts and clarify procedure steps, there are exploded diagrams at the start of each
removal and disassembly section.
5 Numbers are given in the order of the jobs in the exploded diagram. A circled number indicates a
disassembly step.
6 Symbols indicate parts to be lubricated or replaced (see “SYMBOLS”).
7 A job instruction chart accompanies the exploded diagram, providing the order of jobs, names of
parts, notes in jobs, etc.
8 Jobs requiring more information (such as special tools and technical data) are described
sequentially.
2
4
1
8
5
6
7
3
EB003000
1
SYMBOLS
2
GEN
INFO
SPEC
3
4
CHK
ADJ
ENG
5
6
CARB
COOL
7
8
CHAS
ELEC
Symbols 10 to 17 indicate the following.
10
9
10
11
12
13
14
15
16
17
TRBL
SHTG
11
12
13
14
15
16
17
18
19
20
21
24
22
23
25
The following symbols are not relevant to every
vehicle.
Symbols 1 to 9 indicate the subject of each
chapter.
1 General information
2 Specifications
3 Periodic inspection and adjustment
4 Engine
5 Cooling system
6 Carburetor(-s)
7 Chassis
8 Electrical system
9 Troubleshooting
Serviceable with engine mounted
Filling fluid
Lubricant
Special tool
Tightening torque
Wear limit, clearance
Engine speed
Electrical data
Symbols 18 to 23 in the exploded diagrams indicate the types of lubricants and lubrication
points.
18
19
20
21
22
23
Apply engine oil
Apply gear oil
Apply molybdenum disulfide oil
Apply wheel bearing grease
Apply lightweight lithium-soap base grease
Apply molybdenum disulfide grease
Symbols 24 to 25 in the exploded diagrams indicate the following:
24 Apply locking agent (LOCTITE)
25 Use new one
CONTENTS
GENERAL INFORMATION
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SPEEDOMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SPECIFICATIONS
GENERAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHASSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CABLE ROUTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3
3
4
7
PERIODIC INSPECTIONS AND ADJUSTMENTS
PERIODIC MAINTENANCE/LUBRICATION INTERVALS . . . . . . . . . . . 19
CHASSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ADJUSTING THE FRONT FORK LEGS . . . . . . . . . . . . . . . . . . . . . . . 21
CHASSIS
FRONT FORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
CHECKING THE FRONT FORK LEGS . . . . . . . . . . . . . . . . . . . . . . . . 23
ASSEMBLING THE FRONT FORK LEGS . . . . . . . . . . . . . . . . . . . . . . 23
ELECTRICAL
SIGNAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SIGNAL SYSTEM CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FZS600 2000 WIRING DIAGRAM
26
26
28
31
FEATURES
GEN
INFO
GENERAL INFORMATION
FEATURES
SPEEDOMETER
1
2
3
4
Speedometer
Odometer / Tripmeter / Clock
“SELECT” button
“RESET” button
This speedometer is equipped with:
an odometer
two tripmeters
a clock
Odometer and tripmeter modes
When set to “ODO”, the motorcycle’s total mileage is indicated.
When set to “TRIP 1” or “TRIP 2”, the motorcycle’s mileage since the tripmeter was last reset is indicated. Use the tripmeters to estimate how far you can ride on a tank of fuel. This information will enable
you to plan fuel stops in the future.
Selecting a mode
Push the “SELECT” button 3 to change between the odometer mode “ODO”, the tripmeter modes
“TRIP 1” and “TRIP 2”, and the clock mode in the following order:
“ODO” “TRIP 1” “TRIP 2” Clock “ODO”
Resetting a meter
To reset either tripmeter 1 or 2 to 0.0, select either by pushing the “SELECT” button 3 and push the
“RESET” button 4 for at least one second.
Clock mode
To change the display to the clock mode, push the “SELECT” button 3 .
To change the display back to the odometer mode, push the “SELECT” button 3 .
To set the clock
1. Push both the “SELECT” button 3 and “RESET” button 4 for at least two seconds.
2. When the hour digits start flashing, push the “RESET” button 4 to set the hours.
3. Push the “SELECT” button 3 to change the minutes.
4. When the minute digits start flashing, push the “RESET” button 4 to set the minutes.
5. Push the “SELECT” button 3 to start the clock.
NOTE:
After setting the clock, be sure to push the “SELECT” button before turning the main switch to “OFF”,
otherwise the clock will not be set.
–1–
GENERAL SPECIFICATIONS
SPEC
SPECIFICATIONS
GENERAL SPECIFICATIONS
Model
Model code:
Fuel:
Type
Fuel tank capacity
Fuel reserve amount
Tire pressure:
Maximum load-except motorcycle
Loading condition A*
front
rear
Loading condition B*
front
rear
High-speed riding
front
rear
Bulb voltage, wattage quantity:
Headlight
Marker light
Brake/tail light
Front turn signal light
Rear turn signal light
Meter light
Indicator light
Neutral indicator light
High beam indicator light
Oil level warning light
Turn indicator light
Fuel level warning light
Engine temperature warning light
FZS600
5DM7
5DM8
5DM9
Regular unleaded gasoline
20 L
3.5 L
187 kg
0 90 kg
225 kPa (2.25 kg/cm2, 2.25 bar)
250 kPa (2.5 kg/cm2, 2.5 bar)
90 187 kg
225 kPa (2.25 kg/cm2, 2.25 bar)
290 kPa (2.9 kg/cm2, 2.9 bar)
225 kPa (2.25 kg/cm2, 2.25 bar)
290 kPa (2.9 kg/cm2, 2.9 bar)
12 V 60 W/55 W 1
12 V 5 W 1
12 V 21 W/5 W 2
12 V 21 W 2
12 V 21 W 2
12 V 2 W 3
14 V 1.4 W 1
14 V 1.4 W 1
14 V 1.4 W 1
14 V 1.4 W 2
12 V 2 W 1
LED
*Load is the total weight of cargo, rider, passenger and accessories.
–2–
MAINTENANCE SPECIFICATIONS
SPEC
MAINTENANCE SPECIFICATIONS
ENGINE
Item
Valve spring:
Free length
Set length (valve closed)
Compressed pressure
Tilt limit
Direction of winding
IN/EX
IN/EX
IN/EX
IN/EX
IN/EX
Carburetor:
I.D. mark
Main jet
Main air jet
Jet needle
Needle jet
Pilot air jet
Pilot outlet
Pilot jet
Bypass 1
Bypass 2
Bypass 3
Pilot screw
Valve seat size
Starter jet
Starter jet
Throttle valve size
Fuel level
Engine idle speed
Intake vacuum
(M.J)
(M.A.J)
(J.N)
(N.J)
(P.A.J.1)
(P.O)
(P.J)
(B.P.1)
(B.P.2)
(B.P.3)
(P.S)
(V.S)
(G.S.1)
(G.S.2)
(TH.V)
(F.L) (with
special tool)
Standard
Limit
40.09 mm
34.5 mm
131.4 153.0 N (13.4 15.6 kg)
SSS
Clockwise
37.5 mm
SSS
SSS
2.5_/1.8 mm
SSS
5DM1 01 (GB) (N) (SF) (DK) (D) (NL)
5DM1 01 (B) (F) (E) (P) (IRL) (GR)
5DM2 11 (D) (F)
#115
#80
5D86-3/5 (GB) (N) (SF) (DK) (D) (NL)
5D86-3/5 (B) (F) (E) (P) (IRL) (GR)
5D92-3/5 (D) (F)
P-0
#130
0.95
#12.5
0.9
0.8
0.8
2
1.0
0.6
0.8
#110
3.5 mm
SSS
1,150 1,250 r/min
30.7 33.3 kPa (230 250 mmHg)
SSS
SSS
–3–
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SPEC
MAINTENANCE SPECIFICATIONS
CHASSIS
Item
Standard
Limit
Front suspension:
Front fork travel
Fork spring free length
Fitting length
Collar length
Spring Rate
(K1)
(K2)
Stroke
(K1)
(K2)
Optional spring
Oil capacity
Oil level
Oil grade
120 mm
316.8 mm
309.8 mm
183 mm
7.35 N/mm (0.75 kg/mm)
13.72 N/mm (1.4 kg/mm)
0 70 mm
70 120 mm
No
465 cm3
132 mm
Fork oil 10W or equivalent
319 mm
Drive chain:
Type/manufacturer
No. of links
Chain free play
50VA7/DAIDO
110
30 45 mm
TIGHTENING TORQUES
CHASSIS
Part to be tightened
g
Thread size
M6 1.0
Holder, clutch lever 1
–4–
Tightening
torque
Nm
mkg
11
1.1
Remarks
MAINTENANCE SPECIFICATIONS
SPEC
ELECTRICAL
Item
Standard
Limit
Ignition system:
Ignition timing (B.T.D.C.)
Advanced timing (B.T.D.C.)
Advance type
10_/1,250 r/min
50_/4,500 r/min
Digital type
SSS
SSS
SSS
T.C.I.:
Pickup coil resistance
T.C.I. unit model/manufacturer
189 231 Ω Y-L
J4T095/MITSUBISHI
SSS
SSS
Charging system:
Type
Model/manufacturer
Standard output
Stator coil resistance
A.C. magneto
F4T359 /MITSUBISHI
14 V 18 A at 5,000 r/min
0.36 0.44 Ω at 20_C/W-W
SSS
SSS
SSS
SSS
Starter motor:
Model/manufacturer
I.D. number
Output
Armature coil resistance
Brush overall length
Brush spring pressure
Commutator dia.
Mica undercut (depth)
Mica undercut (width)
SM-13/MITSUBA
SM-13
0.7 kW
0.0015 0.0025 Ω at 20_C
10 mm
7.64 10.00 N (779 1,020 gf)
28 mm
0.7 mm
0.8 mm
SSS
SSS
SSS
SSS
4 mm
SSS
27 mm
SSS
SSS
Starter relay:
Model/manufacturer
Amperage rating
Coil winding resistance
MS5F-631 /JIDECO
180 A
4.18 4.62 Ω at 20_C
SSS
SSS
SSS
Horn:
Type
Quantity
Model manufacturer
Maximum amperage
Performance
Coil winding resistance
Plane type
1 pcs
YF-12/NIKKO
3.0 A
105 113 db/2 m
1.15 1.25 Ω at 20_C
SSS
SSS
SSS
SSS
SSS
SSS
Flasher/hazard relay:
Type
Model/manufacturer
Self cancelling device
Hazard flasher device
Flasher frequency
Wattage
Full transistor type
FE246BH/DENSO
No
Yes
75 95 cyl/min
21 W 2 + 3.4 W
SSS
SSS
SSS
SSS
SSS
SSS
Thermostat switch:
Model/manufacture
4BA/DENSO
SSS
–5–
MAINTENANCE SPECIFICATIONS
SPEC
Item
Standard
limit
Starting circuit cut-off relay:
Model/manufacture
Coil winding resistance
G8R-30Y-B/OMRON
202.5 247.5 Ω at 20_C
SSS
SSS
Fuel pump relay:
Model/manufacture
Coil winding resistance
G8R-30Y-B/OMRON
202.5 247.5 Ω at 20_C
SSS
SSS
30 A
20 A
20 A
20 A
10 A
10 A
5A
30 A
20 A
10 A
5A
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
SSS
Amperage for individual circuit:
Main
Headlight
Signal
Ignition
Fan
Parking/Hazard
Back up
Reserve
–6–
CABLE ROUTING
SPEC
EB205000
CABLE ROUTING
1
2
3
4
5
6
7
8
9
10
Throttle cable
Clutch cable
Handlebar switch (left)
Starter cable
Main switch
Main switch lead
Brake hose
Speed sensor lead
Headlight lead
Handlebar switch (right)
A Use a plastic band to fasten together the handlebar switch lead
(L) and the handlebar.
B Use a plastic clamp to fasten together the handlebar switch lead
(left), clutch cable and starter
cable
C Pass the speed sensor lead inside of the clamp code.
–7–
D Pass the brake hose out side of
the speed sensor lead, then use
a plastic clamp to fasten them.
CABLE ROUTING
1
2
3
4
5
6
7
8
9
10
11
Main switch lead
Handlebar switch lead (left)
Clutch cable
Starter cable
Rectifier/ regulator
Horn lead
Box
Air guide plate
Fan motor lead
High tension code
Relay assembly
12
13
14
15
16
17
18
19
20
21
22
Flasher leray
Battery
Starter relay
Battery positive (+) lead
Seat lock cable
Seat lock stay
Cross tube
AC magneto lead
Starter motor lead
Air filter drain hose
Neutral switch
–8–
23
24
25
26
27
28
29
30
31
32
33
SPEC
Sidestand switch lead
Neutral switch lead
Oil level switch lead
Radiator
Rectifier/ regulator lead
Horn
Speed sensor lead
Brake hose
Horn lead
Horn bracket
Rear fender
CABLE ROUTING
34
35
36
37
38
39
40
41
42
43
44
Wire harness
Relay
Fuse box
To front brake switch
To battery negative (–) lead
To starter relay
Starter motor lead
Pickup coupler
Sidestand switch coupler
Oil level / neutral switch coupler
AC magneto coupler
45 Oil level / neutral switch lead
A Use a plastic clamp to fasten the
handlebar switch lead (left),
main switch lead, clutch cable
and starter cable to the frame.
B Pass the fan motor lead through
the guide gear, then into the box.
C Use a plastic clamp to fasten the
horn lead and air guide plate to
the frame.
–9–
SPEC
D When installing the plug cap, the
high tension code should be facing the inside of the body.
E Pass the wire harness, starter
motor lead, AC magneto lead,
sidestand switch lead and oil /
neutral switch lead over the
cross tube.
F Use a plastic clamp to fasten together the wire harness and the
frame.
CABLE ROUTING
G Use a plastic clamp to fasten together the wire harness and the
frame.
H Push couplers into the lock stay
of the frame after connecting
wires.
I Use a plastic band to fasten together wireharness, starter motor lead, AC magneto lead, sidestand switch lead and oil level / neutral switch lead, then hold
SPEC
the clamp to the frame bracket. L Use a steel holder to fasten toPosition the band end to out side
gether the AC magneto lead,
of chassis.
sidestand lead and oil level / neuJ Use a plastic locking tie to fasten
tral switch lead.
the starter motor lead, AC mag- M Pass the air cleaner drain hose
neto lead, sidestand switch lead
in front of the rear arm pivot shaft
and oil level / neutral switch lead
and back of the cross tube.
to the frame bracket. Cut off the N Pass the air cleaner drain hose
excess end of the tie.
through the pipe holder of rear
K Pass the air cleaner drain hose
shock absorber bracket, then draw
through the engine clamp.
it out to the left side of the body.
–10–
CABLE ROUTING
O Use a plastic clamp to fasten together the sidestand switch lead
and the frame.
P Pass the sidestand switch lead
through the bottom of the coolant
pipe.
Q Do not loosen the fan motor lead
here.
R Pass the clutch cable and starter
cable outside of high tension
code#1.
S Use a steel holder to fasten together the speed sensor lead
and outer tube.
T Use a plastic clamp to fix the
speed sensor lead at 3 points after running the lead along the
outside of the brake hose.
First. Fasten the bottom end of
the speed sensor lead without
loosening.
Second. Fasten the lead several
–11–
SPEC
times from the bottom end by
running along the brake hose.
U Pass the hom lead under the
horn bracket, then connect it at
the back of the horn.
V Pass only the starter lead
through the bottom of the joint of
wire harness.
CABLE ROUTING
1
2
3
4
5
6
7
8
9
10
11
12
13
Rear brake switch lead
Battery
Reservoir tank over flow hose
Cross tube
Battery negative (–) lead
Reservoir tank hose
Air filter
To fuel tank
Fuel tank breather hose
Fuel tank drain hose
T.P.S. lead
Box
Speed sensor lead
14
15
16
17
18
19
20
21
22
23
Handlebar switch lead (right)
Throttle cable
Brake hose
Guide wire
Headlight lead
Main switch lead
Reservoir tank
Air filter box bracket
Swingarm bracket
Engine bracket
–12–
SPEC
A Pass the fuel tank drain hose,
fuel tank breather hose and reservoir tank over flow pipe between the rear arm and the engine crankcase.
B Pass the fuel tank drain hose
and fuel tank breather hose between air filter joint #3 and #4.
After installing the fuel tank, pull
it down toward the air filter joint
so that there will be no bend of
loosening between them.
CABLE ROUTING
SPEC
C Pass the T.P.S lead as shown, F Pass the throttle cable, with the J Pass the throttle cable under the
then install cover to the air filter
pull side up, through the center
box.
case.
of the clamp.
K Pass the reservoir tank over flow
D Use a plastic clamp to fasten to- G Pass the throttle cable through
hose and fuel tank drain hose
gether the throttle cables, headthe guide wire installed to the
through the cable holder.
light lead, handlebar switch
handle crown.
L To coolant reservoir tank.
(right) and speed sensor lead.
H To front cowling.
M Pass the battery negative (–)
E Use a plastic locking tie to fasten I Pass the main switch lead under
lead inside of the reservoir hose.
the handlebar switch (right) and
the throttle cables, headlight N Use the plastic clamp to fasten
brake hose to the right front fork
lead, handlebar switch lead
together the rear brake switch
inner tube.
(right) and speed sensor lead,
lead and the frame.
then insert it right side of the box.
The latch of the clamp must face
the outside of the body.
–13–
CABLE ROUTING
O Pass the battery negative lead
and rear brake switch lead inside
the air filter bracket of the frame.
P Pass the reservoir tank over flow
pipe between the air filter case
and cross tube, and then outside
of engine bracket.
Q Use a clamp to fasten together
the coolant reservoir hose and
the bracket rear arm.
–14–
SPEC
CABLE ROUTING
1
2
3
4
5
6
7
8
9
10
11
12
Throttle cable
Speed sensor lead
Handlebar switch lead (right)
Headlight lead
Thermostat housing
Carburetor heater hose
Reservoir tank hose
Throttle cable
Fuel pump
Fuel filter
Fuel tank breather hose
Fuel tank drain hose
13
14
15
16
17
18
19
20
21
22
23
24
Pipe
Fuel hose
T.P.S lead
Fuel pipe
Fuel sender, coupler
Battery negative (–) lead
Battery
Rear brake hose
Rear brake reservoir tank
Rear brake switch lead
Fuse box
Seat lock cable
–15–
25
26
27
28
29
30
31
32
33
34
35
36
SPEC
Ignitor
Rear turn signal light lead (right)
Taillight lead
Rear turn signal light lead (left)
Taillight bracket
Starter motor lead
Starter relay
Relay
Relay assembly
Wire harness
Fuel pump lead coupler
Ignition coil
CABLE ROUTING
37
38
39
40
41
42
43
44
45
46
47
48
Clutch cable
Starter cable
Ground lead
Box
Fan motor lead
Rectifier/ regulator lead
Handlebar switch lead (left)
Main switch lead
Wire harness
13
To taillight
Rear fender
Clamp
SPEC
A Tighten the ground lead and the
the coolant reservoir tank, bethermostat housing together
tween the reservoir hose and the
with a bolt.
battery, then are connected at
B Pass the reservoir hose left side
the right side of the battery.
of thermo stat housing.
G Pass the rear flasher lead (R)
C Do not fasten the high tension
through the rear fender.
cord #4 with locking tie.
H Pass the rear flasher lead (L)
D Use a plastic band to fasten the
through the rear fender.
high tension cord #3, #4.
I Pass the wire harness through
E Fuel pump lead comes over.
the groove of the rear fender.
F Pass the rear brake switch lead J Wire harness shouldn’t come
and battery negative lead under
top of the rear fender rib.
–16–
CABLE ROUTING
K Pass the wire harness inside of P Pass the fuel pump lead between the ignition coil and fuel filthe rear fender rib.
ter, then push under.
L Pass the wireharness under the
Q Use a plastic clamp to fasten tostarter relay.
gether the wire harness and
M Pass the starter motor lead unstay.
der the joint of the harness, then
R Pass the carburetor inlet hose unpull upward.
der the high tension cord #2, #4.
N Set the fuel sender coupler in the
S Use a clamp to fasten the clutch
cross pipe of the frame.
cable and starter cable.
O Use a plastic clamp to fasten together the wire harness and T Use a plastic clamp to fasten
high tension code #2, and #4.
cross pipe of the frame.
–17–
SPEC
U Set the clamp, which is fixed to
the wire harness, in T-stud of the
frame.
V Put the wire harness into the box
through the groove at the back,
then connect it in the box.
CABLE ROUTING
W Pass the rectifier / regulator lead,
fan motor lead, handlebar switch
lead (left), main switch lead,
headlight lead, handlebar switch
lead (right) and speed sensor
lead through front side of the
box, then connecte each coupler
in the box.
X Use a plastic clamp to fasten the
wire harness after passing always under the taillight bracket.
Y Align the connector position of
rear turn signal light leads (left
and right), then bend the rear
–18–
SPEC
PERIODIC MAINTENANCE/LUBRICATION INTERVALS
CHK
ADJ
EB3000000
PERIODIC INSPECTIONS AND ADJUSTMENTS
PERIODIC MAINTENANCE/LUBRICATION INTERVALS
EVERY
NO.
ITEM
CHECKS AND MAINTENANCE JOBS
1
*
Fuel line
Check fuel hoses for cracks or damage.
Replace if necessary.
2
*
Fuel filter
Check condition.
Replace if necessary.
Spark plugs
Check condition.
Clean, regap or replace if necessary.
Valves
Check valve clearance.
Adjust if necessary.
Air filter
Clean or replace if necessary.
Clutch
Check operation.
Adjust or replace cable.
3
4
*
5
6
INITIAL
(1,000 km)
6,000 km
or
6 months
(whichever
comes first)
12,000 km
or
12 months
(whichever
comes first)
√
√
√
√
√
√
Every 42,000 km or 42 months
(whichever comes first)
√
√
√
√
√
7
*
Front brake
Check operation, fluid level and vehicle for fluid leakage.
(See NOTE)
Correct accordingly.
Replace brake pads if necessary.
√
√
√
8
*
Rear brake
Check operation, fluid level and vehicle for fluid leakage.
(See NOTE)
Correct accordingly.
Replace brake pads if necessary.
√
√
√
9
*
Wheels
Check balance, runout and for damage.
Rebalance or replace if necessary.
√
√
10 *
Tires
√
√
11 *
Wheel bearings
Check bearing for looseness or damage.
Replace if necessary.
√
√
12 *
Swingarm
Check swingarm pivoting point for play.
Correct if necessary.
Lubricate with molybdenum disulfide grease every 24,000 km or
24 months (whichever comes first).
√
√
13
Drive chain
Check chain slack.
Adjust if necessary. Make sure that the rear wheel is properly
aligned.
Clean and lubricate.
14 *
Steering bearings
Check bearing play and steering for roughness.
Correct accordingly.
Lubricate with lithium soap base grease every 24,000 km or
24 months (whichever comes first).
√
√
15 *
Chassis fasteners
Make sure that all nuts, bolts and screws are properly tightened.
Tighten if necessary.
√
√
Check tread depth and for damage.
Replace if necessary.
Check air pressure.
Correct if necessary.
–19–
Every 1,000 km and after washing the
motorcycle or riding in the rain
PERIODIC MAINTENANCE/LUBRICATION INTERVALS
CHK
ADJ
EVERY
NO.
ITEM
CHECKS AND MAINTENANCE JOBS
INITIAL
(1,000 km)
6,000 km
or
6 months
(whichever
comes first)
12,000 km
or
12 months
(whichever
comes first)
√
√
√
√
16
Sidestand / centerstand
S Check operation.
S Lubricate and repair if necessary.
17 *
Sidestand switch
S Check operation.
S Replace if necessary.
18 *
Front fork
S Check operation and for oil leakage.
S Correct accordingly.
√
√
19 *
Rear shock absorber
assembly
S Check operation and shock absorber for oil leakage.
S Replace shock absorber assembly if necessary.
√
√
20 *
Rear suspension relay
arm and connecting
arm pivoting points
S Check operation.
S Lubricate with molybdenum disulfide grease every 24,000 km or
24 months (whichever comes first).
√
√
21 *
Carburetors
S Check engine idling speed, synchronization and starter operation.
S Adjust if necessary.
√
√
√
22
Engine oil
S Check oil level and vehicle for oil leakage.
S Correct if necessary.
S Change. (Warm engine before draining.)
√
√
√
23
Engine oil filter
cartridge
S Replace.
√
24 *
Cooling system
S Check coolant level and vehicle for coolant leakage.
S Correct if necessary.
S Change coolant every 24,000 km or 24 months (whichever comes
first).
√
√
√
√
* Since these items require special tools, data and technical skills, they should be serviced by a
Yamaha dealer.
NOTE:
D The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
D Hydraulic brake system
S When disassembling the master cylinder or caliper, always replace the brake fluid. Check the brake
fluid level regularly and fill as required.
S Replace the oil seals on the inner parts of the master cylinder and caliper every two years.
S Replace the brake hoses every four years or if cracked or damaged.
–20–
ADJUSTING THE FRONT FORK LEGS
CHK
ADJ
EAS00152
CHASSIS
ADJUSTING THE FRONT FORK LEGS
The following procedure applies to both of the
front fork legs.
WARNING
Always adjust both front fork legs evenly.
Uneven adjustment can result in poor handling and loss of stability.
Securely support the motorcycle so that
there is no danger of it falling over.
CAUTION:
Grooves are provided to indicate the adjustment position.
Never go beyond the maximum or minimum adjustment positions.
1. Adjust:
spring preload
a. Turn the adjusting bolt 1 in direction a or
b.
Direction a
Spring preload is
increased (suspension is
harder).
Direction b
Spring preload is
decreased (suspension is
softer).
Adjusting positions
Standard: 5
Minimum: 7
Maximum: 1
–21–
FRONT FORK
CHAS
CHASSIS
FRONT FORK
30 Nm (3.0 mkg)
30 Nm (3.0 mkg)
7 Nm (0.7 mkg)
Order
Job name/Part name
Q’ty
Remove the parts in the order listed.
Refer to “FRONT WHEEL AND BRAKE
DISCS” section.
Refer to “FRONT AND REAR BRAKES”
section.
Removing the front fork
Front wheel
Front brake calipers
1
2
3
4
5
Front fender
Bolt (upper bracket)
Cap bolt
Bolt (lower bracket)
Front fork assembly (left/right)
Remarks
1
2
2
2
1/1
–22–
Loosen Refer to “REMOVING/
Loosen INSTALLING THE FRONT
Loosen FORK LEGS” section.
Refer to “REMOVING/INSTALLING THE
FRONT FORK LEGS” section.
For installation, reverse the removal
procedure.
FRONT FORK
CHAS
23 Nm (2.3 mkg)
30 Nm (3.0 mkg)
Order
1
2
3
4
5
6
7
8
9
10
11
12
13
Job name/Part name
Disassembling the front fork
Cap bolt
O-ring
Spacer
Washer
Front fork spring
Dust seal
Oil seal clip
Bolt
Gasket
Damper rod/rebound spring
Inner tube/Inner tube bushing
Oil seal
Washer
Q’ty
Remarks
Disassembly the parts in the order listed.
1
1
1
1
1
1
1
1
1
1/1
1
1
1
–23–
Refer to “ASSEMBLING THE FRONT
FORK LEGS” section.
Refer to “DISASSEMBLING/
ASSEMBLING THE FRONT FORK
LEGS” section.
FRONT FORK
CHAS
23 Nm (2.3 mkg)
30 Nm (3.0 mkg)
Order
14
15
Job name/Part name
Outer tube bushing
Oil flow stopper
Q’ty
1
1/1
–24–
Remarks
Refer to “ASSEMBLING THE FRONT
FORK LEGS” section.
For assembly, reverse the disassembly
procedure.
FRONT FORK
CHAS
CHECKING THE FRONT FORK LEGS
1. Check:
cap bolt O-ring 1
Damage/wear Replace.
EB703700
ASSEMBLING THE FRONT FORK LEGS
1. Fill:
front fork leg
(with the specified amount of the recommended fork oil)
Quantity (each front fork leg)
0.465 L
Yamaha fork and shock oil
10 W or equivalent.
Front fork leg oil level a (from
the top of the inner tube, with the
inner tube fully compressed and
without the fork spring)
132 mm
NOTE:
While filling the front fork leg, keep it upright.
After filling, slowly pump the front fork leg up
and down to distribute the fork oil.
–25–
SIGNAL SYSTEM
EB806000
ELECTRICAL
SIGNAL SYSTEM
CIRCUIT DIAGRAM
–26–
ELEC
SIGNAL SYSTEM
3
4
6
35
40
41
42
43
52
60
Main switch
Battery
Fuse (main)
Flasher relay
Turn switch
Hazard switch
Front turn signal light
Rear turn signal light
Fuse (signal)
Relay 2
–27–
ELEC
SIGNAL SYSTEM
ELEC
SIGNAL SYSTEM CHECK
EB806023
1. If the turn signal light and/or turn indicator
light fails to blink:
1. Bulb and bulb socket
NO CONTINUITY
S Check the bulb and bulb socket for continuity.
Replace the bulb and/or bulb socket.
CONTINUITY
2. Turn switch
S Disconnect the left handlebar switch couplers from the wire harness.
S Set the hazard switch “OFF”
S Check for continuity as follows:
Brown/White 1 – Chocolate 2
Brown/White 1 – Dark green 3
NO CONTINUITY
Replace the left handlebar switch.
CONTINUITY
3. Hazard switch
S Disconnect the left handlebar switch couplers from the wire harness.
S Set the turn switch “Neutral position”
S Check for continuity as follows:
Brown/White 1 – Chocolate 2
Brown/White 1 – Dark green 3
Chocolate 2 – Dark green 3
NO CONTINUITY
Replace the left handlebar switch.
CONTINUITY
:
–28–
SIGNAL SYSTEM
ELEC
:
4. Voltage
S Connect the pocket tester (DC 20 V) to the
flasher relay coupler.
Tester (+) lead Brown terminal 1
Tester (–) lead Frame ground
OUT OF SPECIFICATION
S Turn the main switch to “ON”.
S Check the voltage (12 V) of the “Brown” 1
lead at the flasher relay terminal.
MEETS
SPECIFICATION
The wiring circuit from the main switch to the
flasher relay connector is faulty, repair it.
5. Voltage
S Connect the pocket tester (DC 20 V) to the
flasher relay coupler.
Tester (+) lead Brown/White terminal 1
Tester (–) lead Frame ground
S Turn the main switch to “ON”.
S Turn the turn switch to “L”/“R” or push the
hazard switch.
S Check the voltage (12 V) on the
“Brown/White” 1 lead at the flasher relay
terminal.
OUT OF SPECIFICATION
The flasher relay is faulty, replace it.
MEETS
SPECIFICATION
:
–29–
ELEC
SIGNAL SYSTEM
:
A
6. Voltage
B
S Connect the pocket tester (DC 20 V) to the
bulb socket connector.
A Flasher light
B Turn indicator light
1
2
At the flasher light (left):
Tester (+) lead Chocolate lead 1
Tester (–) lead Frame ground
At the flasher light (right):
Tester (+) lead Dark green lead 2
Tester (–) lead Frame ground
OUT OF SPECIFICATION
S Turn the main switch to “ON”.
S Turn the turn switch to “L”/“R” or push the
hazard switch.
S Check the voltage (12 V) of the “Chocolate”
lead or “Dark green” lead on the bulb socket
connector.
The wiring circuit from the left handlebar
switch to the bulb socket connector is faulty,
repair it.
MEETS
SPECIFICATION
This circuit is not faulty.
–30–
CLOCK
ELEC
CLOCK
EAS00805
The clock fails to come on.
1. Voltage
Connect the pocket tester (DC 20 V) to the
clock coupler.
Tester (+) read Brow 1
Tester (–) read Frame ground
OUT OF SPECIFICATION
Turn the main switch to “ON”.
Check the voltage (12 V) on the “Brown” 1
lead at the clock terminal.
MEETS
SPECIFICATION
The wiring circuit from the main switch to the
clock coupler is faulty, repair it.
2. Clock
OUT OF SPECIFICATION
Check that the clock is operating properly.
When setting the clock after its power
source has been disconnected (e.g., when
the battery is removed), first set the clock to
1:00 AM and then to the correct time.
The clock is faulty, replace it.
MEETS
SPECIFICATION
This circuit is not faulty.
–31–
FZS600 2000 WIRING DIAGRAM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
COLOR CODE
B ......
Br . . . . .
Ch . . . .
Dg . . . .
G .....
Gy . . . .
L ......
Black
Brown
Chocolate
Dark green
Green
Gray
Blue
P ......
Lg . . . . .
O .....
R......
Sb . . . . .
W .....
Y ......
Pink
Light green
Orange
Red
Sky blue
White
Yellow
B/L . . . .
B/R . . .
B/W . . .
B/Y . . .
Br / L . . .
Br / W . .
G/R . . .
Black / Blue
Black / Red
Black / White
Black / Yellow
Brown / Blue
Brown / White
Green / Red
G/W . . .
G/Y . . .
L/B . . . .
L/R . . .
L/W . . .
L/Y . . . .
R/B . . .
Green / White
Green / Yellow
Blue / Black
Blue / Red
Blue / White
Blue / Yellow
Red / Black
R/W . . .
R/Y . . .
W/B . . .
W/G . . .
W/R . . .
Y/B . . .
Y/R . . .
Red / White
Red / Yellow
White / Black
White / Green
White / Red
Yellow / Black
Yellow / Red
A.C. magneto
Rectifier/ regulator
Main switch
Battery
Fuse (back up)
Fuse (main)
Starter relay
Starter motor
Starting circuit cut-off relay
Fuel pump relay
Ignitor unit
Ignition coil
Spark plug
Pick up coil
Throttle position sensor
Neutral switch
Speed sensor
Fuel sender
Thermo switch
(engine temperature)
Diode
Fuel pump
Sidestand switch
Speedometer
Tachometer
Fuel meter
Fuel level warning light
Engine temperature
warning light
Neutral indicator light
Oil level warning light
High beam indicator light
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Turn indicator light
Meter light
Clutch switch
Oil level switch
Flasher relay
Horn
Pass switch
Dimmer switch
Horn switch
Turn switch
Hazard switch
Front turn signal light
Rear turn signal light
Headlight
Tail/ Brake light
Auxiliary light
Fan motor
Thermo switch (fan motor)
Fuse (fan motor)
Fuse (head light)
Rear brake switch
Fuse (signal)
Front brake switch
Light switch
Engine stop switch
Starter switch
Fuse
Alarm
Fuse (parking)
Relay 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement