Artisan Technology Group R&S CMU 200 Radio Communication Tester Quick Start Guide

Artisan Technology Group is your source for quality
new and certified-used/pre-owned equipment
• FAST SHIPPING AND
DELIVERY
• TENS OF THOUSANDS OF
IN-STOCK ITEMS
• EQUIPMENT DEMOS
• HUNDREDS OF
MANUFACTURERS
SUPPORTED
• LEASING/MONTHLY
RENTALS
• ITAR CERTIFIED
SECURE ASSET SOLUTIONS
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff
at our full-service, in-house repair center
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins
www.artisantg.com/WeBuyEquipment
InstraView REMOTE INSPECTION
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical
specifications, manuals, and documentation
SM
Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com
Contact us: (888) 88-SOURCE | [email protected] | www.artisantg.com
Quick Start Guide
Universal
Radio Communication Tester
R&S CMU 200
1100.0008.02/53
Printed in Germany
Test and Measurement Division
1100.4961.62-01
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of the owners.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
R&S CMU Documentation Map
Quick Start Guide
The present quick start guide describes everything that is needed
to put the instrument into operation and helps you to get familiar
with the radio communication tester. In particular, the quick start
guide describes the safety-related aspects to be observed when
setting up or operating the instrument. The guide contains:
• The product brochure and specifications
•
Safety instructions
•
Certificates
•
Customer support information, Rohde & Schwarz addresses
•
Chapter 1: Preparation for Use
•
Chapter 2: Getting Started
•
Index for Chapter 1 and Chapter 2
Documentation CD-ROM
The CD-ROM provides the complete user documentation for the
radio communication testers R&S CMU 200 and R&S CMU 300:
• Printable versions of the complete operating manual
(including the contents of this quick start guide) and the
service manual
•
Printable versions of the manuals for R&S CMU network test
options (see order list on the following page) and accessories
•
Help systems corresponding to the contents of the quick start
guide and to the complete operating manual
•
The product brochure and specifications in printable form.
•
Application notes and articles
•
Links to different useful sites in the R&S internet.
Optional Documentation
The complete operating manual for the radio communication
testers R&S CMU 200 and R&S CMU 300 and the manuals for
the network test options provide the complete reference
information for operation and programming. The service manual
instrument contains the performance test and other servicerelated information.
Printed versions of the manuals can be ordered as options; see
ordering information on the next page.
Note:
1100.4961.62
The CD-ROM delivered with the instrument contains
printable (.pdf) versions of all these manuals.
1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
List of Printed Manuals
The following operating manuals are related to the Universal Radio Communication Tester R&S
CMU 200 and to network test options for the R&S CMU 200. Printed manuals can be ordered from
Rohde & Schwarz using the order numbers listed below.
For Options
Manual
Order Number
Operating Manual
CMU 200/300
1100.4984.12
Service Manual Inst.
CMU 200/300
1100.4903.82
Operating Manual
CMU-K20/-K21/K22/-K23/-K24/-K26
1115.6088.12
Type
Description
Stock No.
CMU 200
CMU 300
Univ. Radio Communication Tester
for mobile stations / UE
for base stations
1100.0008.02/53
1100.0008.03
CMU 200
CMU 300
Univ. Radio Communication Tester
for mobile stations / UE
for base stations
1100.0008.02/53
1100.0008.03
CMU-K20
CMU-K21
CMU-K22
CMU-K23
CMU-K24
CMU-K26
GSM400-MS for CMU-B21
GSM900-MS for CMU-B21
GSM1800-MS for CMU-B21
GSM1900-MS for CMU-B21
GSM850-MS for CMU-B21
GSM GT800 for CMU-B21
1115.5900.02
1115.6007.02
1115.6107.02
1115.6207.02
1115.6307.02
1115.6507.02
CMU-K42
CMU-K43
CMU-K44
CMU-K45
CMU-K47
CMU-K92
GPRS software extension for GSM
EGPRS software extension for GSM
Dual Transfer Mode
AMR GSM for CMU200
Smart Alignment @ GSM-MS
(E)GPRS Application Testing
1115.4691.02
1115.6907.02
1157.4277.02
1150.3100.02
1157.4477.02
1157.4077.02
Operating Manual
CMU-K27/-K28
1115.6688.12
CMU-K27
CMU-K28
TDMA800-MS for CMU-B21
TDMA1900-MS for CMU-B21
1115.6607.02
1115.6707.02
Operating Manual
CMU-K29
1115.6888.12
CMU-K29
AMPS-MS for CMU-B21
1115.6807.02
Operating Manual
CMU-K53
1115.5081.12
CMU-K53
Bluetooth for CMU
1115.5000.02
Operating Manual
CMU-K61…-K69
1115.4962.12
CMU-K65
CMU-K66
CMU-K67
CMU-K68
CMU-K69
CMU-K61
CMU-K62
CMU-K63
WCDMA UE TX Test (3GPP/FDD)
WCDMA UE DL Generator
WCDMA UE Band III Signalling
WCDMA UE Band I Signalling
WCDMA UE Band II Signalling
WCDMA UE Band IV Signalling
WCDMA UE Band V Signalling
WCDMA UE Band VI Signalling
1115.4891.02
1115.5100.02
1150.3000.02
1115.5300.02
1115.5400.02
1157.3670.02
1157.3770.02
1157.3870.02
CMU-K64
HSDPA 3.6 Mbps
1157.3970.02
Operating Manual
CMU-K81/-K82
1115.5581.12
CMU-K81
CMU-K82
CDMA800-MS (IS95) for CMU-B81
CDMA1900-MS (IS95) for CMU-B81
1115.5500.02
1115.5600.02
Operating Manual
CMU-K83/-K84/
-K85/-K86
1150.0382.12
CMU-K83
CMU-K84
CMU-K85
CMU-K86
CDMA2000-MS (450 MHz band)
CDMA2000-MS (cellular band)
CDMA2000-MS (PCS band)
CDMA2000-MS (IMT-2000 band)
1150.3500.02
1150.3600.02
1150.3700.02
1150.3800.02
CMU-K87
CDMA2000 Data Testing
1150.4007.02
CMU-K88
1xEV-DO for CMU-B88
1150.3900.02
Operating Manual
CMU-K88
1100.4961.62
1150.3998.12
2
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-2
R&S CMU 200 – Equipment Supplied
The R&S CMU is delivered with the following items:
• Universal Radio Communication Tester R&S CMU 200
•
An AC power cable
•
The following documentation (see documentation map on the previous pages):
-
The present quick start guide for R&S CMU 200
-
The documentation CD-ROM
Please note the instructions for unpacking and setting up the instrument starting on p. 1.10.
R&S CMU Models
This manual describes the following models of the Universal Radio Communication Tester R&S
CMU:
• Universal Radio Communication Tester R&S CMU 200, stock no. 1100.0008.02, for all mobile
station and user equipment tests including Bluetooth™ device tests.
• Universal Radio Communication Tester R&S CMU 200, stock no. 1100.0008.53, only for
Bluetooth™ device tests.
The Universal Radio Communication Tester R&S CMU 300, stock no. 1100.0008.03, is described
by a separate operating manual, stock no. 1100.4978.62.
1100.4961.62
3
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Supplement to the Quick Start Guide
for Universal Radio Communication Tester
R&S CMU 200
Addendum to the data sheet, no. 0758.0039.22 (V06.00, May 2004)
For CMU 200 instruments delivered with WCDMA MS SW ≥ V3.60 the WCDMA RF generator signal
quality specification on page 25 is extended for 16QAM as follows:
Signal quality
16QAM
Error vector magnitude (EVM)
Global EVM for 16QAM
reference setup: 3GPP TS34.121 FRC HSet3 for 16 QAM
1100.4961.62
<8 %, rms
DS
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Before putting the product into operation for
the first time, make sure to read the following
Safety Instructions
Rohde & Schwarz makes every effort to keep the safety standard of its products up to date and to offer
its customers the highest possible degree of safety. Our products and the auxiliary equipment required
for them are designed and tested in accordance with the relevant safety standards. Compliance with
these standards is continuously monitored by our quality assurance system. This product has been
designed and tested in accordance with the EC Certificate of Conformity and has left the manufacturer’s
plant in a condition fully complying with safety standards. To maintain this condition and to ensure safe
operation, observe all instructions and warnings provided in this manual. If you have any questions
regarding these safety instructions, Rohde & Schwarz will be happy to answer them.
Furthermore, it is your responsibility to use the product in an appropriate manner. This product is
designed for use solely in industrial and laboratory environments or in the field and must not be used in
any way that may cause personal injury or property damage. You are responsible if the product is used
for an intention other than its designated purpose or in disregard of the manufacturer's instructions. The
manufacturer shall assume no responsibility for such use of the product.
The product is used for its designated purpose if it is used in accordance with its operating manual and
within its performance limits (see data sheet, documentation, the following safety instructions). Using
the products requires technical skills and knowledge of English. It is therefore essential that the
products be used exclusively by skilled and specialized staff or thoroughly trained personnel with the
required skills. If personal safety gear is required for using Rohde & Schwarz products, this will be
indicated at the appropriate place in the product documentation.
Symbols and safety labels
Observe
operating
instructions
Weight
indication for
units >18 kg
Supply
voltage
ON/OFF
1171.0000.42-01.00
Danger of
electric
shock
Standby
indication
Direct
current
(DC)
Warning!
Hot
surface
PE terminal
Alternating
current (AC)
Ground
Direct/alternat
ing current
(DC/AC)
Ground
terminal
Attention!
Electrostatic
sensitive
devices
Device fully protected
by double/reinforced
insulation
Sheet 1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Safety Instructions
Observing the safety instructions will help prevent personal injury or damage of any kind caused by
dangerous situations. Therefore, carefully read through and adhere to the following safety instructions
before putting the product into operation. It is also absolutely essential to observe the additional safety
instructions on personal safety that appear in other parts of the documentation. In these safety
instructions, the word "product" refers to all merchandise sold and distributed by Rohde & Schwarz,
including instruments, systems and all accessories.
Tags and their meaning
DANGER
This tag indicates a safety hazard with a high potential of risk for the
user that can result in death or serious injuries.
WARNING
This tag indicates a safety hazard with a medium potential of risk for the
user that can result in death or serious injuries.
CAUTION
This tag indicates a safety hazard with a low potential of risk for the user
that can result in slight or minor injuries.
ATTENTION
This tag indicates the possibility of incorrect use that can cause damage
to the product.
NOTE
This tag indicates a situation where the user should pay special attention
to operating the product but which does not lead to damage.
Basic safety instructions
1. The product may be operated only under
the operating conditions and in the
positions specified by the manufacturer. Its
ventilation must not be obstructed during
operation. Unless otherwise specified, the
following requirements apply to
Rohde & Schwarz products:
IP protection 2X, pollution severity 2,
overvoltage category 2, use only in
enclosed spaces, max. operation altitude
max. 2000 m.
2. Applicable local or national safety
regulations and rules for the prevention of
accidents must be observed in all work
performed. The product may be opened
only by authorized, specially trained
personnel. Prior to performing any work on
the product or opening the product, the
instrument must be disconnected from the
supply network. Any adjustments,
replacements of parts, maintenance or
repair must be carried out only by technical
personnel authorized by Rohde & Schwarz.
Only original parts may be used for
replacing parts relevant to safety (e.g.
power switches, power transformers,
fuses). A safety test must always be
performed after parts relevant to safety
have been replaced
1171.0000.42-01.00
(visual inspection, PE conductor test,
insulation resistance measurement,
leakage current measurement, functional
test).
3. As with all industrially manufactured goods,
the use of substances that induce an
allergic reaction (allergens) such as
aluminum cannot be generally excluded. If
you develop an allergic reaction (such as a
skin rash, frequent sneezing, red eyes or
respiratory difficulties), consult a physician
immediately to determine the cause.
4. Depending on the function, certain products
such as RF radio equipment can produce
an elevated level of electromagnetic
radiation. Considering that unborn life
requires increased protection, pregnant
women should be protected by appropriate
measures. Persons with pacemakers may
also be endangered by electromagnetic
radiation. The employer is required to
assess workplaces where there is a special
risk of exposure to radiation and, if
necessary, take measures to avert the
danger.
Sheet 2
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Safety Instructions
5. Operating the products requires special
training and intense concentration.
Disabled persons should not use the
products unless it is made certain that their
disability has no adverse effects while they
are operating the products.
6. Prior to switching on the product, it must be
ensured that the nominal voltage setting on
the product matches the nominal voltage of
the AC supply network. If a different voltage
is to be set, the power fuse of the product
may have to be changed accordingly.
7. In the case of products of safety class I with
movable power cord and connector,
operation is permitted only on sockets with
earthing contact and protective earth
connection.
8. Intentionally breaking the protective earth
connection either in the feed line or in the
product itself is not permitted. Doing so can
result in the danger of an electric shock
from the product. If extension cords or
connector strips are implemented, they
must be checked on a regular basis to
ensure that they are safe to use.
9. If the product has no power switch for
disconnection from the AC supply, the plug
of the connecting cable is regarded as the
disconnecting device. In such cases, it
must be ensured that the power plug is
easily reachable and accessible at all times
(length of connecting cable approx. 2 m).
Functional or electronic switches are not
suitable for providing disconnection from
the AC supply. If products without power
switches are integrated in racks or systems,
a disconnecting device must be provided at
the system level.
10. Never use the product if the power cable is
damaged. By taking appropriate safety
measures and carefully laying the power
cable, ensure that the cable cannot be
damaged and that no one can be hurt by
e.g. tripping over the cable or suffering an
electric shock.
12. Do not insert the plug into sockets that are
dusty or dirty. Insert the plug firmly and all
the way into the socket. Otherwise this can
result in sparks, fire and/or injuries.
13. Do not overload any sockets, extension
cords or connector strips; doing so can
cause fire or electric shocks.
14. For measurements in circuits with voltages
Vrms > 30 V, suitable measures (e.g.
appropriate measuring equipment, fusing,
current limiting, electrical separation,
insulation) should be taken to avoid any
hazards.
15. Ensure that the connections with
information technology equipment comply
with IEC950/EN60950.
16. Never remove the cover or part of the
housing while you are operating the
product. This will expose circuits and
components and can lead to injuries, fire or
damage to the product.
17. If a product is to be permanently installed,
the connection between the PE terminal on
site and the product's PE conductor must
be made first before any other connection
is made. The product may be installed and
connected only by a skilled electrician.
18. For permanently installed equipment
without built-in fuses, circuit breakers or
similar protective devices, the supply circuit
must be fused in such a way that suitable
protection is provided for users and
products.
19. Do not insert any objects into the openings
in the housing that are not designed for this
purpose. Never pour any liquids onto or into
the housing. This can cause short circuits
inside the product and/or electric shocks,
fire or injuries.
20. Use suitable overvoltage protection to
ensure that no overvoltage (such as that
caused by a thunderstorm) can reach the
product. Otherwise the operating personnel
will be endangered by electric shocks.
11. The product may be operated only from
TN/TT supply networks fused with max.
16 A.
1171.0000.42-01.00
Sheet 3
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Safety Instructions
21. Rohde & Schwarz products are not
protected against penetration of water,
unless otherwise specified (see also safety
instruction 1.). If this is not taken into
account, there exists the danger of electric
shock or damage to the product, which can
also lead to personal injury.
22. Never use the product under conditions in
which condensation has formed or can form
in or on the product, e.g. if the product was
moved from a cold to a warm environment.
23. Do not close any slots or openings on the
product, since they are necessary for
ventilation and prevent the product from
overheating. Do not place the product on
soft surfaces such as sofas or rugs or
inside a closed housing, unless this is well
ventilated.
24. Do not place the product on heatgenerating devices such as radiators or fan
heaters. The temperature of the
environment must not exceed the maximum
temperature specified in the data sheet.
25. Batteries and storage batteries must not be
exposed to high temperatures or fire. Keep
batteries and storage batteries away from
children. If batteries or storage batteries are
improperly replaced, this can cause an
explosion (warning: lithium cells). Replace
the battery or storage battery only with the
matching Rohde & Schwarz type (see
spare parts list). Batteries and storage
batteries are hazardous waste. Dispose of
them only in specially marked containers.
Observe local regulations regarding waste
disposal. Do not short-circuit batteries or
storage batteries.
1171.0000.42-01.00
26. Please be aware that in the event of a fire,
toxic gases that may be hazardous to your
health may escape from the product.
27. Please be aware of the weight of the
product. Be careful when moving it;
otherwise you may injure your back or other
parts of your body.
28. Do not place the product on surfaces,
vehicles, cabinets or tables that for reasons
of weight or stability are unsuitable for this
purpose. Always follow the manufacturer's
installation instructions when installing the
product and fastening it to objects or
structures (e.g. walls and shelves).
29. If you use the product in a vehicle, it is the
sole responsibility of the driver to drive the
vehicle safely. Adequately secure the
product in the vehicle to prevent injuries or
other damage in the event of an accident.
Never use the product in a moving vehicle if
doing so could distract the driver of the
vehicle. The driver is always responsible for
the safety of the vehicle; the manufacturer
assumes no responsibility for accidents or
collisions.
30. If a laser product (e.g. a CD/DVD drive) is
integrated in a Rohde & Schwarz product,
do not use any other settings or functions
than those described in the documentation.
Otherwise this may be hazardous to your
health, since the laser beam can cause
irreversible damage to your eyes. Never try
to take such products apart, and never look
into the laser beam.
Sheet 4
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Informaciones de seguridad
Por favor lea imprescindiblemente antes de
la primera puesta en funcionamiento las
siguientes informaciones de seguridad
Informaciones de seguridad
Es el principio de Rohde&Schwarz de tener a sus productos siempre al día con los estandards de
seguridad y de ofrecer a sus clientes el máximo grado de seguridad. Nuestros productos y todos los
equipos adicionales son siempre fabricados y examinados según las normas de seguridad vigentes.
Nuestra sección de gestión de la seguridad de calidad controla constantemente que sean cumplidas
estas normas. Este producto ha sido fabricado y examinado según el comprobante de conformidad
adjunto según las normas de la CE y ha salido de nuestra planta en estado impecable según los
estandards técnicos de seguridad. Para poder preservar este estado y garantizar un funcionamiento
libre de peligros, deberá el usuario atenerse a todas las informaciones, informaciones de seguridad y
notas de alerta. Rohde&Schwarz está siempre a su disposición en caso de que tengan preguntas
referentes a estas informaciones de seguridad.
Además queda en la responsabilidad del usuario utilizar el producto en la forma debida. Este producto
solamente fue elaborado para ser utilizado en la indústria y el laboratorio o para fines de campo y de
ninguna manera deberá ser utilizado de modo que alguna persona/cosa pueda ser dañada. El uso del
producto fuera de sus fines definidos o despreciando las informaciones de seguridad del fabricante
queda en la responsabilidad del usuario. El fabricante no se hace en ninguna forma responsable de
consecuencias a causa del maluso del producto.
Se parte del uso correcto del producto para los fines definidos si el producto es utilizado dentro de las
instrucciones del correspondiente manual del uso y dentro del margen de rendimiento definido (ver
hoja de datos, documentación, informaciones de seguridad que siguen). El uso de los productos hace
necesarios conocimientos profundos y el conocimeinto del idioma inglés. Por eso se deberá tener en
cuenta de exclusivamente autorizar para el uso de los productos a personas péritas o debidamente
minuciosamente instruidas con los conocimientos citados. Si fuera necesaria indumentaria de
seguridad para el uso de productos de R&S, encontrará la información debida en la documentación del
producto en el capítulo correspondiente.
Símbolos y definiciones de seguridad
Ver manual
de
instrucciones
del uso
Informaciones
para
maquinaria
con uns peso
de > 18kg
potencia EN
MARCHA/PARADA
1171.0000.42-01.00
Peligro de
golpe de
corriente
Indicación
Stand-by
¡Cuidado!
Superficie
caliente
Corriente
continua
DC
Conexión a
conductor
protector
Corriente
alterna AC
Conexión
a tierra
Corriente
continua/alterna
DC/AC
Conexión
a masa
conductora
¡Cuidado!
Elementos de
construción
con peligro de
carga
electroestática
El aparato está
protegido en su
totalidad por un
aislamiento de
doble refuerzo
página 1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Informaciones de seguridad
Tener en cuenta las informaciones de seguridad sirve para tratar de evitar daños y peligros de toda
clase. Es necesario de que se lean las siguientes informaciones de seguridad concienzudamente y se
tengan en cuenta debidamente antes de la puesta en funcionamiento del producto. También deberán
ser tenidas en cuenta las informaciones para la protección de personas que encontrarán en otro
capítulo de esta documentación y que también son obligatorias de seguir. En las informaciones de
seguridad actuales hemos juntado todos los objetos vendidos por Rohde&Schwarz bajo la
denominación de „producto“, entre ellos también aparatos, instalaciones así como toda clase de
accesorios.
Palabras de señal y su significado
PELIGRO
Indica un punto de peligro con gran potencial de riesgo para el
ususario.Punto de peligro que puede llevar hasta la muerte o graves
heridas.
ADVERTENCIA
Indica un punto de peligro con un protencial de riesgo mediano para el
usuario. Punto de peligro que puede llevar hasta la muerte o graves
heridas .
CUIDADO
Indica un punto de peligro con un protencial de riesgo pequeño para el
usuario. Punto de peligro que puede llevar hasta heridas leves o
pequeñas
ATENCIÓN
Indica la posibilidad de utilizar mal el producto y a consecuencia
dañarlo.
INFORMACIÓN
Indica una situación en la que deberían seguirse las instrucciones en el
uso del producto, pero que no consecuentemente deben de llevar a un
daño del mismo.
Informaciones de seguridad elementales
1. El producto solamente debe ser utilizado
según lo indicado por el fabricante
referente a la situación y posición de
funcionamiento sin que se obstruya la
ventilación. Si no se convino de otra
manera, es para los productos R&S
válido lo que sigue:
modo de protección IP 2X, grado de
suciedad 2, categoría de sobrecarga
eléctrica 2, utilizar solamente en
estancias interiores, utilización hasta
2000 m sobre el nivel del mar.
2. En todos los trabajos deberán ser
tenidas en cuenta las normas locales de
seguridad de trabajo y de prevención de
accidentes. El producto solamente debe
de ser abierto por personal périto
autorizado. Antes de efectuar trabajos en
el producto o abrirlo deberá este ser
desconectado de la corriente. El ajuste,
el cambio de partes, la manutención y la
reparación deberán ser solamente
efectuadas por electricistas autorizados
por R&S.Si se reponen partes con
importancia para los aspectos de
seguridad (por ejemplo el enchufe, los
1171.0000.42-01.00
transformadores o los fusibles),
solamente podrán ser sustituidos por
partes originales.Despues de cada
recambio de partes elementales para la
seguridad deberá ser efectuado un
control de seguridad (control a primera
vista, control de conductor protector,
medición de resistencia de aislamiento,
medición de medición de la corriente
conductora, control de funcionamiento).
3. Como en todo producto de fabricación
industrial no puede ser excluido en
general de que se produzcan al usarlo
elementos que puedan generar alergias,
los llamados elementos alergénicos (por
ejemplo el aluminio). Si se producieran
en el trato con productos R&S
reacciones alérgicas, como por ejemplo
urticaria, estornudos frecuentes, irritación
de la conjuntiva o dificultades al respirar,
se deberá consultar inmediatamente a
un médico para averigurar los motivos de
estas reacciones.
página 2
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Informaciones de seguridad
4. Ciertos productos, como por ejemplo las
instalaciones de radiación HF, pueden a
causa de su función natural, emitir una
radiación electromagnética aumentada.
En vista a la protección de la vida en
desarrollo deberían ser protegidas
personas embarazadas debidamente.
También las personas con un bypass
pueden correr peligro a causa de la
radiación electromagnética. El
empresario está comprometido a valorar
y señalar areas de trabajo en las que se
corra un riesgo de exposición a
radiaciones aumentadas de riesgo
aumentado para evitar riesgos.
5. La utilización de los productos requiere
instrucciones especiales y una alta
concentracion en el manejo. Personas
minusválidas solamente deberán utilizar
estos productos si está por seguro de
que a causa de su handicap no podrá
surgir ninguna restricción en el manejo
del producto.
6. Antes de la puesta en marcha del
producto se deberá tener por seguro de
que la tensión preseleccionada en el
producto equivalga a la del la red de
distribución. Si es necesario cambiar la
preselección de la tensión también se
deberán en caso dabo cambiar los
fusibles correspondientes del prodcuto.
7. Productos de la clase de seguridad I con
alimentación móvil y enchufe individual
de producto solamente deberán ser
conectados para el funcionamiento a
tomas de corriente de contacto de
seguridad y con conductor protector
conectado.
de función o electrónicos no son aptos
para la el corte de la red eléctrica. Si los
productos sin interruptor están
integrados en construciones o
instalaciones, se deberá instalar el
interruptor al nivel de la instalación.
10. No utilice nunca el producto si está
dañado el cable eléctrico. Asegure a
través de las medidas de protección y de
instalación adecuadas de que el cable de
eléctrico no pueda ser dañado o de que
nadie pueda ser dañado por él, por
ejemplo al tropezar o por un golpe de
corriente.
11. Solamente está permitido el
funcionamiento en redes de distribución
TN/TT aseguradas con fusibles de como
máximo 16 A.
12. Nunca conecte el enchufe en tomas de
corriente sucias o llenas de polvo.
Introduzca el enchufe por completo y
fuertemente en la toma de corriente. Si
no tiene en consideración estas
indicaciones se arriesga a que se
originen chispas, fuego y/o heridas.
13. No sobrecargue las tomas de corriente,
los cables de extensión o los enchufes
de extensión ya que esto pudiera causar
fuego o golpes de corriente.
14. En las mediciones en circuitos de
corriente con una tensión de entrada de
Ueff > 30 V se deberá tomar las
precauciones debidas para impedir
cualquier peligro (por ejemplo medios de
medición adecuados, seguros, limitación
de tensión, corte protector, aislamiento
etc.).
8. Queda prohibida toda clase de
interrupción intencionada del conductor
protector, tanto en la toma de corriente
como en el mismo producto ya que
puede tener como consecuencia el
peligro de golpe de corriente por el
producto. Si se utilizaran cables o
enchufes de extensión se deberá poner
al seguro, que es controlado su estado
técnico de seguridad.
15. En caso de conexión con aparatos de la
técnica informática se deberá tener en
cuenta que estos cumplan los requisitos
de la EC950/EN60950.
9. Si el producto no está equipado con un
interruptor para desconectarlo de la red,
se deberá considerar el enchufe del
cable de distribución como interruptor.
En estos casos deberá asegurar de que
el enchufe sea de fácil acceso y nabejo
(medida del cable de distribución
aproximadamente 2 m). Los interruptores
17. Si un producto es instalado fijamente en
un lugar, se deberá primero conectar el
conductor protector fijo con el conductor
protector del aparato antes de hacer
cualquier otra conexión. La instalación y
la conexión deberán ser efecutadas por
un electricista especializado.
1171.0000.42-01.00
16. Nunca abra la tapa o parte de ella si el
producto está en funcionamiento. Esto
pone a descubierto los cables y
componentes eléctricos y puede causar
heridas, fuego o daños en el producto.
página 3
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Informaciones de seguridad
18. En caso de que los productos que son
instalados fijamente en un lugar sean sin
protector implementado, autointerruptor
o similares objetos de protección, deberá
la toma de corriente estar protegida de
manera que los productos o los usuarios
estén suficientemente protegidos.
19. Por favor, no introduzca ningún objeto
que no esté destinado a ello en los
orificios de la caja del aparato. No vierta
nunca ninguna clase de líquidos sobre o
en la caja. Esto puede producir corto
circuitos en el producto y/o puede causar
golpes de corriente, fuego heridas.
20. Asegúrese con la protección adecuada
de que no pueda originarse en el
producto una sobrecarga por ejemplo a
causa de una tormenta. Si no se verá el
personal que lo utilice expuesto al peligro
de un golpe de corriente.
21. Los productos R&S no están protegidos
contra el agua si no es que exista otra
indicación, ver también punto 1. Si no se
tiene en cuenta esto se arriesga el
peligro de golpe de corriente o de daños
en el producto lo cual también puede
llevar al peligro de personas.
22. No utilice el producto bajo condiciones
en las que pueda producirse y se hayan
producido líquidos de condensación en o
dentro del producto como por ejemplo
cuando se desplaza el producto de un
lugar frío a un lugar caliente.
23. Por favor no cierre ninguna ranura u
orificio del producto, ya que estas son
necesarias para la ventilación e impiden
que el producto se caliente demasiado.
No pongan el producto encima de
materiales blandos como por ejemplo
sofás o alfombras o dentro de una caja
cerrada, si esta no está suficientemente
ventilada.
24. No ponga el producto sobre aparatos
que produzcan calor, como por ejemplo
radiadores o calentadores. La
temperatura ambiental no debe superar
la temperatura máxima especificada en
la hoja de datos.
25. Baterías y acumuladores no deben de
ser expuestos a temperaturas altas o al
fuego. Guardar baterías y acumuladores
fuera del alcance de los niños. Si las
baterías o los acumuladores no son
cambiados con la debida atención
existirá peligro de explosión (atención
1171.0000.42-01.00
celulas de Litio). Cambiar las baterías o
los acumuladores solamente por los del
tipo R&S correspondiente (ver lista de
piezas de recambio). Baterías y
acumuladores son deshechos
problemáticos. Por favor tirenlos en los
recipientes especiales para este fín. Por
favor tengan en cuenta las
prescripciones nacionales de cada país
referente al tratamiento de deshechos.
Nunca sometan a las baterías o
acumuladores a un corto circuito.
26. Tengan en consideración de que en caso
de un incendio pueden escaparse gases
tóxicos del producto, que pueden causar
daños a la salud.
27. Por favor tengan en cuenta el peso del
producto. Muevanlo cuidadosamente ya
que el peso puede causar lesiones de la
espalda u otros daños físicos.
28. No sitúe el producto encima de
superficies, vehículos, estantes o mesas,
que por sus características de peso o de
estabilidad no sean aptas para él. Siga
siempre las instrucciones de instalación
del fabricante cuando instale y asegure
el producto en objetos o estructuras (por
ejemplo paredes y estantes).
29. Si llega a utilizar el producto dentro de
un vehículo, queda en la responsabilidad
absoluta del conductor que conducir el
vehículo de manera segura. Asegure el
producto dentro del vehículo
debidamente para evitar en caso de un
accidente las lesiones u otra clase de
daños. No utilice nunca el producto
dentro de un vehículo en movimiento si
esto pudiera distraer al conductor.
Siempre queda en la responsabilidad
absoluta del conductor la seguridad del
vehículo y el fabricante no asumirá
ninguna clase de responsabilidad por
accidentes o colisiones.
30. Dado el caso de que esté integrado und
producto de laser en un producto R&S
(por ejemplo CD/DVD-ROM) no utilice
otras instalaciones o funciones que las
descritas en la documentación. De otra
manera pondrá en peligro su salud, ya
que el rayo laser puede dañar
irreversiblemente sus ojos. Nunca trate
de descomponer estos productos. Nunca
mire dentro del rayo laser.
página 4
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
EC Certificate of Conformity
Certificate No.: 99035, page 1
This is to certify that:
Equipment type
Stock No.
Designation
CMU200
CMU300
1100.0008.02/.53
1100.0008.03
Universal Radio Communication Tester
complies with the provisions of the Directive of the Council of the European Union on the
approximation of the laws of the Member States
- relating to electrical equipment for use within defined voltage limits
(73/23/EEC revised by 93/68/EEC)
- relating to electromagnetic compatibility
(89/336/EEC revised by 91/263/EEC, 92/31/EEC, 93/68/EEC)
Conformity is proven by compliance with the following standards:
EN61010-1 : 2001-12
EN61326-1 : 1997 + A1 : 1998
For the assessment of electromagnetic compatibility, the limits of radio interference for Class
B equipment as well as the immunity to interference for operation in industry have been used
as a basis.
Affixing the EC conformity mark as from 1999
Munich, 2004-09-10
1100.0008.02-s1-
ROHDE & SCHWARZ GmbH & Co. KG
Mühldorfstr. 15, D-81671 München
Central Quality Management FS-QZ / Radde
CE
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-11
EC Certificate of Conformity
Certificate No.: 99035, page 2
This is to certify that:
Equipment type
Stock No.
Designation
CMU-B11
CMU-B12
CMU-B15
CMU-B17
CMU-B21
CMU-B41
CMU-B52
CMU-B53
CMU-B54
CMU-B56
CMU-B66
CMU-B68
CMU-B71
CMU-B73
CMU-B76
1100.5000.02
1100.5100.02
1100.6006.02
1100.6906.02
1100.5200.02/.14
1100.5300.02
1100.5400.02/.14
1100.5700.02/.14
1150.2604.14
1150.1850.14
1149.9509.02
1149.9809.02
1100.6406.02
1150.2004.02
1150.0601.02
Reference Oscillator
Reference Oscillator
Additional RF und IF Connections
IQ and IF Interfaces
Versatile Signalling Unit
Audio Generator and Analyzer
Spreech Codec for Versatile Signalling Unit
Bluetooth Extension
Sig. Module
3GPP Signalling Unit
Versatile Base Band Board
Layer1 Board
ABIS Interface Unit
Analog Telephon Line Interface
Layer1 Board for WCDMA
complies with the provisions of the Directive of the Council of the European Union on the
approximation of the laws of the Member States
- relating to electrical equipment for use within defined voltage limits
(73/23/EEC revised by 93/68/EEC)
- relating to electromagnetic compatibility
(89/336/EEC revised by 91/263/EEC, 92/31/EEC, 93/68/EEC)
Conformity is proven by compliance with the following standards:
EN61010-1 : 2001-12
EN61326-1 : 1997 + A1 : 1998
For the assessment of electromagnetic compatibility, the limits of radio interference for Class
B equipment as well as the immunity to interference for operation in industry have been used
as a basis.
Affixing the EC conformity mark as from 1999
Munich, 2004-09-10
1100.0008.02-s2-
ROHDE & SCHWARZ GmbH & Co. KG
Mühldorfstr. 15, D-81671 München
Central Quality Management FS-QZ / Radde
CE
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-17
EC Certificate of Conformity
Certificate No.: 99035, page 3
This is to certify that:
Equipment type
Stock No.
Designation
CMU-B81
CMU-B82
CMU-B83
CMU-B85
CMU-B87
CMU-B88
CMU-B95
CMU-B99
CMU-U61
CMU-Z1
1100.6506.02
1150.0201.02/.04
1150.0301.02/.04/.12/.14
1100.7002.02/.04/.12
1150.2404.02/.04
1158.9908.02
1159.0504.02
1150.1250.02
1100.5500.02
1100.7490.02
CDMA(IS95) Signalling Unit
ACCESS Board für CDMA Signalling Unit
CDMA2000 Signalling Unit
Speech Codec for CDMA2000
Message Monitor for CDMA2000
1xEV-DO Extension
Additional RF Generator
RF1 Level Range identical to RF2
Floppy Disk Drive
Memory Card
complies with the provisions of the Directive of the Council of the European Union on the
approximation of the laws of the Member States
- relating to electrical equipment for use within defined voltage limits
(73/23/EEC revised by 93/68/EEC)
- relating to electromagnetic compatibility
(89/336/EEC revised by 91/263/EEC, 92/31/EEC, 93/68/EEC)
Conformity is proven by compliance with the following standards:
EN61010-1 : 2001-12
EN61326-1 : 1997 + A1 : 1998
For the assessment of electromagnetic compatibility, the limits of radio interference for Class
B equipment as well as the immunity to interference for operation in industry have been used
as a basis.
Affixing the EC conformity mark as from 1999
Munich, 2004-09-10
1100.0008.02-s3-
ROHDE & SCHWARZ GmbH & Co. KG
Mühldorfstr. 15, D-81671 München
Central Quality Management FS-QZ / Radde
CE
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-4
Customer Support
Technical support – where and when you need it
For quick, expert help with any Rohde & Schwarz equipment, contact one of our
Customer Support Centers. A team of highly qualified engineers provides telephone
support and will work with you to find a solution to your query on any aspect of the
operation, programming or applications of Rohde & Schwarz equipment.
Up-to-date information and upgrades
To keep your Rohde & Schwarz equipment always up-to-date,
please subscribe to an electronic newsletter at
http://www.rohde-schwarz.com/www/response.nsf/newsletterpreselection
or request the desired information and upgrades via email from your Customer Support
Center (addresses see below).
Feedback
We want to know if we are meeting your support needs. If you have any comments
please email us and let us know [email protected].
USA & Canada
Rest of World
Monday to Friday (except US-state holidays)
8:00 AM – 8:00 PM Eastern Standard Time (EST)
Monday to Friday (except German-state holidays)
08:00 – 17:00 Central European Time (CET)
USA:
888-test-rsa (888-837-8772) (opt 2)
From outside USA: +1 410 910 7800 (opt 2)
Fax:
410 910 7801
Europe:+49 (0) 180 512 42 42
From outside Europe: +49 89 4129 13776
Fax:
+49 (0) 89 41 29 637 78
E-Mail: [email protected]
E-Mail: [email protected]
1007.8684.14-03.00
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Adressen/Addresses
FIRMENSITZ/HEADQUARTERS
(Tel) Phone
(Fax) Fax
E-mail
(Tel) +49 (89) 41 29-0
(Fax) +49 89 4129-121 64
[email protected]
Rohde & Schwarz GmbH & Co. KG
Mühldorfstraße 15 · D-81671 München
Postfach 80 14 69 · D-81614 München
Austria
(Tel) +43 (1) 602 61 41-0
Rohde & Schwarz-Österreich Ges.m.b.H.
(Fax) +43 (1) 602 61 41-14
Am Europlatz 3
[email protected]
Gebäude B
1120 Wien
Azerbaijan
Rohde & Schwarz Azerbaijan
Liaison Office Baku
ISR Plaza, 5th floor
340 Nizami Str.
370000 Baku
Bangladesh
BIL Consortium Ltd.
Corporate Office
House-33, Road-4, Block-F
Banani, Dhaka-1213
Barbados
siehe / see Mexico
Belarus
siehe/see Ukraine
Belgium
Rohde & Schwarz Belgium N.V.
Excelsiorlaan 31 Bus 1
1930 Zaventem
Belize
siehe / see Mexico
Bermuda
siehe/see Mexico
BosniaHerzegovina
siehe/see Slovenia
Brazil
Rohde & Schwarz Do Brasil Ltda.
(Tel) +55 (11) 56 44 86 11
Av. Alfredo Egidio de Souza Aranha n°
(general)·+55
177,
(11) 56 44 86 25 (sales)
1° andar - Santo Amaro
(Fax) +55 (11) 56 44 86 36
04726-170 Sao Paulo - SP
[email protected]
Brunei
George Keen Lee Equipment Pte Ltd.
#11-01 BP Tower
396 Alexandra Road
Singapore 119954
Bulgaria
Rohde & Schwarz
Representation Office Bulgaria
39, Fridtjof Nansen Blvd.
1000 Sofia
(Tel) +359 (2) 96 343 34
(Fax) +359 (2) 963 21 97
[email protected]
(Tel) +1 (613) 592 80 00
(Fax) +1 (613) 592 80 09
[email protected]
WERKE/PLANTS
(Tel) +49 (8331) 108-0
Rohde & Schwarz Messgerätebau GmbH
(Fax) +49 (8331) 108-11 24
Riedbachstraße 58 · D-87700 Memmingen
Postfach 1652 · D-87686 Memmingen [email protected]
Rohde & Schwarz GmbH & Co. KG
(Tel) +49 (9923) 857-0
Werk Teisnach
(Fax) +49 (9923) 857-11 74
Kaikenrieder Straße 27 · D-94244 Teisnach [email protected]
Postfach 1149 · D-94240 Teisnach
Rohde & Schwarz GmbH & Co. KG
(Tel) +49 (2203) 49-0
Dienstleistungszentrum Köln
(Fax) +49 (2203) 49 51-229
Graf-Zeppelin-Straße 18 · D-51147 Köln
info.rsdc@rohdePostfach 98 02 60 · D-51130 Köln
schwarz.com·[email protected]
TOCHTERUNTERNEHMEN/SUBSIDIARIES
Rohde & Schwarz Vertriebs-GmbH
Mühldorfstraße 15 · D-81671 München
Postfach 80 14 69 · D-81614 München
(Tel) +49 (89) 41 29-137 74
(Fax) +49 (89) 41 29-137 77
[email protected]
Rohde & Schwarz International GmbH
Mühldorfstraße 15 · D-81671 München
Postfach 80 14 60 · D-81614 München
(Tel) +49 (89) 41 29-129 84
(Fax) +49 (89) 41 29-120 50
[email protected]
Rohde & Schwarz Engineering and Sales
GmbH
Mühldorfstraße 15 · D-81671 München
Postfach 80 14 29 · D-81614 München
(Tel) +49 (89) 41 29-137 11
(Fax) +49 (89) 41 29-137 23
[email protected]
R&S BICK Mobilfunk GmbH
(Tel) +49 (5042) 998-0
Fritz-Hahne-Str. 7 · D-31848 Bad Münder
(Fax) +49 (5042) 998-105
Postfach 2062 · D-31844 Bad Münder
[email protected]
Rohde & Schwarz FTK GmbH
Wendenschlossstraße 168, Haus 28
D-12557 Berlin
(Tel) +49 (30) 658 91-122
(Fax) +49 (30) 655 50-221
[email protected]
Canada
Rohde & Schwarz SIT GmbH
Agastraße 3
D-12489 Berlin
(Tel) +49 (30) 658 84-0
(Fax) +49 (30) 658 84-183
[email protected]
Rohde & Schwarz Canada Inc.
555 March Rd.
Kanata, Ontario K2K 2M5
Chile
(Tel) +49 (2203) 49-5 23 25
(Fax) +49 (2203) 49-5 23 36
[email protected]
Dymeq Ltda.
Av. Larrain 6666
Santiago
China
Rohde & Schwarz China Ltd.
Representative Office Beijing
6F, Parkview Center
2 Jiangtai Road
Chao Yang District
Beijing 100016
R&S Systems GmbH
Graf-Zeppelin-Straße 18 D-51147 Köln
Postfach 98 02 60 D-51130 Köln
ADRESSEN WELTWEIT/ADDRESSES WORLDWIDE
Albania
siehe/see Austria
Algeria
Rohde & Schwarz
Bureau d'Alger
5B Place de Laperrine
16035 Hydra-Alger
(Tel) +213 (21) 48 20 18
(Fax) +213 (21) 69 46 08
Antilles (Neth.) siehe / see Mexico
Argentina
Precision Electronica S.R.L.
Av. Pde Julio A. Roca 710 - 6° Piso
1067 Buenos Aires
Australia
Rohde & Schwarz (Australia) Pty. Ltd.
Sales Support
Unit 6
2-8 South Street
Rydalmere, N.S.W. 2116
(Tel) +541 (14) 331 10 67
(Fax) +541 (14) 334 51 11
[email protected]
(Tel) +61 (2) 88 45 41 00
(Fax) +61 (2) 96 38 39 88
[email protected]
Rohde & Schwarz China Ltd.
Representative Office Shanghai
Room 807-809, Central Plaza
227 Huangpi North Road
Shanghai 200003
Rohde & Schwarz China Ltd.
Representative Office Guangzhou
Room 2903, Metro Plaza
183 Tian He North Road
Guangzhou 510075
(Tel) +994 (12) 93 31 38
(Fax) +994 (12) 93 03 14
[email protected]
(Tel) +880 (2) 881 06 53
(Fax) +880 (2) 882 82 91
(Tel) +32 (2) 721 50 02
(Fax) +32 (2) 725 09 36
[email protected]
(Tel) +656 276 06 26
(Fax) +656 276 06 29
[email protected]
(Tel) +56 (2) 339 20 00
(Fax) +56 (2) 339 20 10
[email protected]
(Tel) +86 (10) 64 31 28 28
(Fax) +86 (10) 64 37 98 88
[email protected]
(Tel) +86 (21) 63 75 00 18
(Fax) +86 (21) 63 75 91 70
[email protected]
(Tel) +86 (20) 87 55 47 58
(Fax) +86 (20) 87 55 47 59
[email protected]
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Adressen/Addresses
China
Rohde & Schwarz China Ltd.
Representative Office Chengdu
Unit G, 28/F, First City Plaza
308 Shuncheng Avenue
Chengdu 610017
(Tel) +86 (28) 86 52 76 06
(Fax) +86 (28) 86 52 76 10
[email protected]
Rohde & Schwarz China Ltd.
Representative Office Xian
Room 603, Jin Xin International
No. 99 Heping Road
Xian 710001
(Tel) +86 (29) 87 41 53 77
(Fax) +86 (29) 87 20 65 00
[email protected]
Germany
siehe / see Mexico
Croatia
siehe/see Slovenia
Cuba
siehe / see Mexico
Cyprus
Hinis Telecast Ltd.
Agiou Thoma 18
Kiti
Larnaca 7550
Czech Republic Rohde & Schwarz Praha, s.r.o.
Hadovka Office Park
Evropská 2590/33c
16000 Praha 6
Zweigniederlassung Mitte, Geschäftsstelle
(Tel) +49 (2203) 807-0
Köln
(Fax) +49 (2203) 807-650
Niederkasseler Straße 33 · D-51147 Köln
[email protected]
Postfach 900 149 · D-51111 Köln
Denmark
Egypt
Rohde & Schwarz Danmark A/S
Ejby Industrivej 40
2600 Glostrup
(Tel) +45 (43) 43 66 99
(Fax) +45 (43) 43 77 44
[email protected]
U.A.S. Universal Advanced Systems
31 Manshiet El-Bakry Street
Heliopolis
11341 Cairo
El Salvador
siehe/see Mexico
Estonia
Rohde & Schwarz Danmark A/S
Estonian Branch Office
Narva mnt. 13
10151 Tallinn
Finland
Rohde & Schwarz Finland Oy
Taivaltie 5
01610 Vantaa
France
Rohde & Schwarz France
Immeuble "Le Newton"
9-11, rue Jeanne Braconnier
92366 Meudon La Forêt Cédex
(Tel) +20 (2) 455 67 44
(Fax) +20 (2) 256 17 40
[email protected]
Germany
(Tel) +33 (2) 99 51 97 00
(Fax) +33 (2) 99 51 98 77
Zweigniederlassungen der Rohde &
Schwarz Vertriebs-GmbH/Branch offices of
Rohde & Schwarz Vertriebs-GmbH
Zweigniederlassung Nord, Geschäftsstelle
(Tel) +49 (30) 34 79 48-0
Berlin
(Fax) +49 (30) 34 79 48 48
Ernst-Reuter-Platz 10 · D-10587 Berlin
[email protected]
Postfach 100620 · D-10566 Berlin
Zweigniederlassung Süd, Geschäftsstelle
Nürnberg
Donaustraße 36
D-90451 Nürnberg
(Tel) +49 (911) 642 03-0
(Fax) +49 (911) 642 03-33
[email protected]
Kop Engineering Ltd.
P.O. Box 11012
3rd Floor Akai House, Osu
Accra North
(Tel) +233 (21) 77 89 13
(Fax) +233 (21) 701 06 20
[email protected]
Greece
Mercury S.A.
6, Loukianou Str.
10675 Athens
(Tel) +302 (10) 722 92 13
(Fax) +302 (10) 721 51 98
[email protected]
Guatemala
siehe/see Mexico
Guiana
siehe / see Mexico
Haiti
siehe / see Mexico
Honduras
siehe/see Mexico
Hong Kong
Electronic Scientific Engineering
9/F North Somerset House
Taikoo Place
979 King's Road, Quarry Bay
Hong Kong
Hungary
Rohde & Schwarz
Budapesti Iroda
Váci út 169
1138 Budapest
Iceland
siehe/see Denmark
India
Rohde & Schwarz India Pvt. Ltd.
244, Okhla Industrial Estate
Phase - III
New Delhi 110 020
(Tel) +91 (11) 26 32 63 81
(Fax) +91 (11) 26 32 63 73
[email protected]
Rohde & Schwarz India Pvt. Ltd.
Bangalore Office
No. 24, Service Road, Domlur
2nd Stage Extension
Bangalore - 560 071
(Tel) +91 (80) 535 23 62
(Fax) +91 (80) 535 03 61
[email protected]
Rohde & Schwarz India Pvt. Ltd.
Hyderabad Office
302 & 303, Millennium Centre
6-3-1099/1100, Somajiguda
Hyderabad - 500 016
(Tel) +91 (40) 23 32 24 16
(Fax) +91 (40) 23 32 27 32
[email protected]
(Tel) +358 (207) 60 04 00
(Fax) +358 (207) 60 04 17
[email protected]
Niederlassung/Subsidiary Rennes
37 Rue du Bignon
Bâtiment A
35510 Cesson Sévigné
(Tel) +49 (89) 41 86 95-0
(Fax) +49 (89) 40 47 64
[email protected]
Ghana
(Tel) +372 (6) 14 31 23
(Fax) +372 (6) 14 31 21
[email protected]
(Tel) +33 (0) 141 36 10 00
(Fax) +33 (0) 141 36 11 11
[email protected]
Zweigniederlassung Süd, Geschäftsstelle
München
Mühldorfstraße 15 · D-81671 München
Postfach 80 14 69 · D-81614 München
Zweigniederlassung Mitte, Geschäftsstelle
(Tel) +49 (6102) 20 07-0
Neu-Isenburg
(Fax) +49 (6102) 20 07 12
Siemensstraße 20 D-63263 Neu-Isenburg [email protected]
Postfach 16 51 D-63236 Neu-Isenburg
(Tel) +357 (24) 42 51 78
(Fax) +357 (24) 42 46 21
[email protected]
(Tel) +420 (2) 24 31 12 32
(Fax) +420 (2) 24 31 70 43
[email protected]
(Tel) +49 (228) 918 90-0
(Fax) +49 (228) 25 50 87
[email protected]
Zweigniederlassung Nord, Geschäftsstelle
(Tel) +49 (40) 38 61 83 - 00
Hamburg
(Fax) +49 (40) 38 61 83 - 20
Vierenkamp 6 D-22423 Hamburg
[email protected]
Rohde & Schwarz China Ltd.
(Tel) +86 (755) 82 03 11 98
Representative Office Shenzhen
(Fax) +86 (755) 82 03 30 70
Room 1901, Central Business [email protected]
No. 88 Fuhua Yilu
Futian District
Shenzhen 518026
Costa Rica
Zweigniederlassung Büro Bonn
Josef-Wirmer-Straße 1-3 · D-53123 Bonn
Postfach 140264 · D-53057 Bonn
(Tel) +852 (25) 07 03 33
(Fax) +852 (25) 07 09 25
[email protected]
(Tel) +36 (1) 412 44 60
(Fax) +36 (1) 412 44 61
[email protected]
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Adressen/Addresses
India
Indonesia
Iran
Rohde & Schwarz India Pvt. Ltd.
Mumbai Office
B-603, Remi Bizcourt, Shah Industrial
Estate, Off Veera Desai Road
Andheri West
Mumbai - 400 058
(Tel) +91 (22) 26 30 18 10
(Fax) +91 (22) 26 73 20 81
[email protected]
PT Rohde & Schwarz Indonesia
Graha Paramita 5th Floor
Jln. Denpasar Raya Blok D-2
Jakarta 12940
(Tel) +62 (21) 252 36 08
(Fax) +62 (21) 252 36 07
[email protected]·[email protected]
Rohde & Schwarz Iran
Liaison Office Tehran
Groundfloor No. 1, 14th Street
Khaled Eslamboli (Vozara) Ave.
15117 Tehran
(Tel) +98 (21) 872 42 96
(Fax) +98 (21) 871 90 12
[email protected]
Ireland
siehe/see United Kingdom
Israel
Eastronics Ltd.
Measurement Products
11 Rozanis St.
P.O.Box 39300
Tel Aviv 61392
(Tel) +972 (3) 645 87 77
(Fax) +972 (3) 645 86 66
[email protected]
J.M. Moss (Engineering) Ltd.
Communications Products
9 Oded Street
P.O.Box 967
52109 Ramat Gan
(Tel) +972 (3) 631 20 57
(Fax) +972 (3) 631 40 58
[email protected]
Rohde & Schwarz Italia S.p.a.
Centro Direzionale Lombardo
Via Roma 108
20060 Cassina de Pecchi (MI)
(Tel) +39 (02) 95 70 41
(Fax) +39 (02) 95 30 27 72
[email protected]
Rohde & Schwarz Italia S.p.a.
Via Tiburtina 1182
00156 Roma
(Tel) +39 (06) 41 59 81
(Fax) +39 (06) 41 59 82 70
[email protected]
Italy
Jamaica
siehe / see Mexico
Japan
Rohde & Schwarz Japan K.K.
Tokyo Office
711 Bldg., Room 501 (5th floor)
7-11-18 Nishi-Shinjuku
Shinjuku-ku
Tokyo 160-00023
Jordan
(Tel) +81 (3) 59 25 12 88
(Fax) +81 (3) 59 25 12 90
[email protected]
Rohde & Schwarz Japan K.K.
Shin-Yokohama Office
KM Daiichi Bldg., 8F
2-13-13 Kouhoku-ku
Yokohama-shi
Kanagawa 222-0033
(Tel) +81 (4) 54 77 35 70
Rohde & Schwarz Japan K.K.
Osaka Office
TEK Dai 2 Bldg., 8F
1-13-20 Esaka-shi
Suita-shi
Osaka-fu 564-0063
(Tel) +81 (6) 63 10 96 51
Jordan Crown Engineering & Trading Co.
Jabal Amman, Second Circle
Youssef Ezzideen Street
P.O.Box 830414
Amman, 11183
(Tel) +962 (6) 462 17 29
(Fax) +962 (6) 465 96 72
[email protected]
Kazakhstan
Rohde & Schwarz Kazakhstan
Representative Office Almaty
Pl. Respubliki 15
480013 Almaty
Kenya
Excel Enterprises Ltd
Dunga Road
P.O.Box 42 788
Nairobi
Korea
Rohde & Schwarz Korea Ltd.
83-29 Nonhyun-Dong, Kangnam-Ku
(Tel) +7 (32) 72 67 23 54
(Fax) +7 (32) 72 67 23 46
[email protected]
(Tel) +254 (2) 55 80 88
(Fax) +254 (2) 54 46 79
(Tel) +82 (2) 34 85 19 00
(Fax) +82 (2) 547 43 00
[email protected]·[email protected]
Seoul 135-010
Kuwait
Group Five Trading & Contracting Co.
Mezzanine Floor
Al-Bana Towers
Ahmad Al Jaber Street
Sharq
Latvia
Rohde & Schwarz Danmark A/S
Latvian Branch Office
Merkela iela 21-301
1050 Riga
Lebanon
Rohde & Schwarz
Liaison Office Riyadh
P.O.Box 361
Riyadh 11411
Netcom
P.O.Box 55199
Op. Ex-Presidential Palace
Horch Tabet
Beirut
(Tel) +965 (244) 91 72/73/74
(Fax) +965 (244) 95 28
[email protected]
(Tel) +371 (7) 50 23 55
(Fax) +371 (7) 50 23 60
[email protected]
(Tel) +966 (1) 465 64 28 Ext. 303
(Fax) +966 (1) 465 64 28 Ext. 229
[email protected]
(Tel) +961 (1) 48 69 99
(Fax) +961 (1) 49 05 11
[email protected]
Liechtenstein
siehe/see Switzerland
Lithuania
Rohde & Schwarz Danmark A/S
Lithuanian Branch Office
Lukiskiu 5-228
2600 Vilnius
Luxembourg
siehe/see Belgium
Macedonia
NETRA
Sarski odred 7
1000 Skopje
Malaysia
Rohde & Schwarz Malaysia Sdn Bhd
(Tel) +60 (3) 20 94 00 33
Suite 10.04, Level 10, Wisma E&C
(Fax) +60 (3) 20 94 24 33
No. 2 Lorong Dungun Kiri
[email protected]
Damansara Heights
50490 Kuala-Lumpur
Malta
Tektraco International Technology Ltd.(Tel) +356 (21) 37 43 00 or 37 80 88
121, B'Kara Road
(Fax) +356 (21) 37 66 67
San Gwann SGN 08
[email protected]
Mexico
Rohde & Schwarz de Mexico
S. de R.L. de C.V.
German Centre Oficina 4-2-2
Av. Santa Fé 170
Col. Lomas de Santa Fé
01210 Mexico D.F.
Moldava
siehe/see Austria
Nepal
ICTC Pvt. Ltd.
Hattisar, Post Box No. 660
Kathmandu
(Tel) +370 (5) 239 50 10
(Fax) +370 (5) 239 50 11
[email protected]
(Tel) +389 (2) 329 82 30
(Fax) +389 (2) 317 74 88
[email protected]
(Tel) +52 (55) 85 03 99 13
(Fax) +52 (55) 85 03 99 16
[email protected]
(Tel) +977 (1) 443 48 95
(Fax) +977 (1) 443 49 37
[email protected]
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Adressen/Addresses
Netherlands
Rohde & Schwarz Nederland B.V.
Perkinsbaan 1
3439 ND Nieuwegein
New Zealand
Nichecom
1 Lincoln Ave.
Tawa, Wellington
(Tel) +31 (30) 600 17 00
(Fax) +31 (30) 600 17 99
[email protected]
(Tel) +64 (4) 232 32 33
(Fax) +64 (4) 232 32 30
[email protected]
Nicaragua
siehe/see Mexico
Nigeria
Ferrostaal Abuja
Plot 3323, Barada Close
P.O.Box 8513, Wuse
Off Amazon Street
Maitama, Abuja
Norway
Rohde & Schwarz Norge AS
Enebakkveien 302 B
1188 Oslo
Oman
Mustafa Sultan Science & Industry Co.LLC.
Test & Measurement Products
Way No. 3503
Building No. 241
Postal Code 112
Al Khuwair, Muscat
Pakistan
Siemens Pakistan
23, West Jinnah Avenue
Islamabad
Panama
siehe/see Mexico
Papua New
Guinea
siehe/see Australia
Paraguay
siehe/see Argentina
Philippines
Rohde & Schwarz (Philippines) Inc.
Unit 2301, PBCom Tower
6795, Ayala Ave. cor. Herrera St.
Makati City
Poland
Rohde & Schwarz SP.z o.o.
Przedstawicielstwo w Polsce
ul. Stawki 2, Pietro 28
00-193 Warszawa
Portugal
Rohde & Schwarz Portugal, Lda.
Alameda Antonio Sergio
7-R/C - Sala A
2795-023 Linda-a-Velha
Republic
Dominican
siehe/see Mexico
Romania
Rohde & Schwarz
Representation Office Bucharest
89 Eroii Sanitari Bldv., sector 5
050472 Bucuresti
Russian
Federation
Saudi Arabia
(Tel) +234 (9) 413 52 51
(Fax) +234 (9) 413 52 50
[email protected]
Saudi Arabia
Gentec
Haji Abdullah Alireza & Co. Ltd.
P.O.Box 43054
Riyadh
(Tel) +966 (1) 293 20 35
(Fax) +966 (1) 466 16 57
[email protected]
SerbiaMontenegro
Rohde & Schwarz
Representative Office Belgrade
Tose Jovanovica 7
11030 Beograd
(Tel) +381 (11) 305 50 25
(Fax) +381 (11) 305 50 24
[email protected]
Singapore
Rohde & Schwarz Regional Headquarters
Singapore Pte. Ltd.
1 Kaki Bukit View
#05-01/02 Techview
Singapore 415 941
Rohde & Schwarz Systems &
Communications Asia Pte Ltd
Service
1 Kaki Bukit View
#04-01/07 Techview
Singapore 415 941
(Tel) +47 (23) 38 66 00
(Fax) +47 (23) 38 66 01
[email protected]
(Tel) +968 63 60 00
(Fax) +968 60 70 66
[email protected]
(Tel) +92 (51) 227 22 00
(Fax) +92 (51) 227 54 98
[email protected]
(Tel) +65 68 46 37 10
(Fax) +65 68 46 00 29
[email protected]
Slovak
Republic
Specialne systemy a software, a.s.
Svrcia ul. 3
841 04 Bratislava 4
Slovenia
Rohde & Schwarz
Representative Office Ljubljana
Tbilisijska 89
1000 Ljubljana
South Africa
Protea Data Systems (Pty.) Ltd.
Communications and Measurement Division
Private Bag X19
Bramley 2018
(Tel) +27 (11) 719 57 00
(Fax) +27 (11) 786 58 91
[email protected]
Protea Data Systems (Pty.) Ltd.
Cape Town Branch
Unit G9, Centurion Business Park
Bosmandam Road
Milnerton
Cape Town, 7441
(Tel) +27 (21) 555 36 32
(Fax) +27 (21) 555 42 67
[email protected]
(Tel) +63 (2) 753 14 44
(Fax) +63 (2) 753 14 56
(Tel) +48 (22) 860 64 94
(Fax) +48 (22) 860 64 99
[email protected]
(Tel) +65 68 46 18 72
(Fax) +65 68 46 12 52
Spain
(Tel) +351 (21) 415 57 00
(Fax) +351 (21) 415 57 10
[email protected]
(Tel) +421 (2) 65 42 24 88
(Fax) +421 (2) 65 42 07 68
[email protected]
(Tel) +386 (1) 423 46 51
(Fax) +386 (1) 423 46 11
[email protected]
Rohde & Schwarz Espana S.A.
Salcedo, 11
28034 Madrid
(Tel) +34 (91) 334 10 70
(Fax) +34 (91) 729 05 06
[email protected]
Rohde & Schwarz Espana S.A.
Av. Princep d'Astúries, 66
08012 Barcelona
(Tel) +34 (93) 415 15 68
(Fax) +34 (93) 237 49 95
[email protected]
Sri Lanka
Dynatel Communications (PTE) Ltd.
451/A Kandy Road
Kelaniya
Sudan
SolarMan Co. Ltd.
P.O.Box 11 545
North of Fraouq Cementry 6/7/9 Bldg. 16
Karthoum
Rohde & Schwarz International GmbH
(Tel) +7 (095) 745 88 50 to 53
119180, Yakimanskaya nab., 2
(Fax) +7 (095) 745 88 54
Moscow
[email protected]
Sweden
Rohde & Schwarz Sverige AB
Flygfältsgatan 15
128 30 Skarpnäck
(Tel) +46 (8) 605 19 00
(Fax) +46 (8) 605 19 80
[email protected]
Rohde & Schwarz International GmbH (Tel) +966 (1) 293 2035
Liaison Office Riyadh
(Fax) +966 (1) 466 1657
c/o Haji Abdullah Alireza Co. Ltd. [email protected]
P.O.Box 361
Riyadh 11411
Switzerland
Roschi Rohde & Schwarz AG
Mühlestr. 7
3063 Ittigen
(Tel) +41 (31) 922 15 22
(Fax) +41 (31) 921 81 01
[email protected]
Syria
Electro Scientific Office
Baghdad Street
Dawara Clinical Lab. Bldg
P.O.Box 8162
Damascus
(Tel) +40 (21) 411 20 13
(Fax) +40 (21) 410 68 46
[email protected]
(Tel) +94 (112) 90 80 01
(Fax) +94 (112) 91 04 69 69
[email protected]
(Tel) +249 (183) 47 31 08
(Fax) +249 (183) 47 31 38
[email protected]
(Tel) +963 (11) 231 59 74
(Fax) +963 (11) 231 88 75
[email protected]
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Adressen/Addresses
Taiwan
Rohde & Schwarz Taiwan (Pvt.) Ltd.
(Tel) +886 (2) 28 93 10 88
Floor 14, No. 13, Sec. 2, Pei-Tou Road
(Fax) +886 (2) 28 91 72 60
Taipei 112
[email protected]
Tanzania
SSTL Group
P.O. Box 7512
Dunga Street Plot 343/345
Dar Es Salaam
Thailand
Rohde & Schwarz International Thailand
2nd floor Gems Tower
Bangrak, Suriyawong
Bangkok 10600
(Tel) +255 (22) 276 00 37
(Fax) +255 (22) 276 02 93
[email protected]
Schmidt Electronics (Thailand) Ltd.
Messtechnik
202 Le Concorede Tower, 23rd Fl.
Ratchadaphisek Rd.
Huay kwang
Bangkok 10320
(Tel) +66 (2) 200 07 29
(Fax) +66 (2) 267 00 79
siehe/see Mexico
Tunisia
Teletek
71, Rue Alain Savary
Residence Alain Savary (C64)
Cité el Khadra
1003 Tunis
Turkey
Rohde & Schwarz International GmbH
Liaison Office Istanbul
Bagdat Cad. 191/3, Arda Apt. B-Blok
81030 Selamicesme-Istanbul
Ukraine
Rohde & Schwarz
Representative Office Kiev
4, Patris Loumoumba ul.
01042 Kiev
Aeromarine S.A.
Cerro Largo 1497
11200 Montevideo
USA
(Tel) +1 (410) 910 78 00
Rohde & Schwarz, Inc.
(Fax) +1 (410) 910 78 01
Eastern Regional Office (US Headquarters)
[email protected]
8661A Robert Fulton Drive
Columbia, MD 21046-2265
(Tel)
(Fax)
(Tel) +216 (71) 77 33 88
(Fax) +216 (71) 77 05 53
[email protected]
(Tel) +90 (216) 385 19 17
(Fax) +90 (216) 385 19 18
[email protected]
(Tel) +38 (044) 268 60 55
(Fax) +38 (044) 268 83 64
[email protected]
Rohde & Schwarz International GmbH
Liaison Office Middle East
Vertrieb
P.O. Box 31156
Abu Dhabi
Rohde & Schwarz Bick Mobile
Communication
P.O.Box 17466
JAFZ, PPU ZG-07
Dubai
(Tel) +44 (870) 735 16 42
(Fax) +44 (1252) 81 14 77
[email protected]
(Tel) +598 (2) 400 39 62
(Fax) +598 (2) 401 85 97
[email protected]
Rohde & Schwarz, Inc.
Central Regional Office / Systems & EMI
Products
8080 Tristar Drive
Suite 120
Irving, TX 75063
(Tel) +1 (469) 713 53 00
(Fax) +1 (469) 713 53 01
[email protected]
Rohde & Schwarz, Inc.
R&D and Application Support
8905 SW Nimbus Ave
Suite 240
Beaverton, OR 97008
(Tel) +1 (503) 403 47 00
(Fax) +1 (503) 403 47 01
[email protected]
Rohde & Schwarz, Inc.
Western Regional Office
7700 Irvine Center Drive
Suite 100
Irvine, CA 92618
(Tel) +1 (949) 885 70 00
(Fax) +1 (949) 885 70 01
[email protected]
Rohde & Schwarz, Inc.
Service & Calibration Center
8661A Robert Fulton Drive
Columbia, MD 21046-2265
(Tel) +1 (410) 910 50 02
(Fax) +1 (410) 910 79 31
[email protected]
Vietnam
Rohde & Schwarz Representative Office
Vietnam
Unit 807, 8/F, Schmidt Tower
239 Xuan Thuy Road
Cau Giay District
Hanoi
West Indies
siehe/see Mexico
(Tel) +84 (4) 834 20 46
(Tel) +971 (2) 6335 670
(Fax) +971 (2) 6335 671
Dario [email protected]
(Tel) +971 (4) 883 71 35
(Fax) +971 (4) 883 71 36
Rohde & Schwarz Emirates L.L.C.
ESNAAD Premisses at Mussafah, P.O.Box
31156
Abu Dhabi
Rohde & Schwarz UK Ltd.
Ancells Business Park
Fleet
Hampshire GU51 2UZ
Uruguay
(Tel) +66 (2) 880 93 47
(Fax) +66 (2) 880 93 47
Trinidad
&Tobago
United
Kingdom
Rohde & Schwarz UK Ltd.
3000 Manchester Business Park
Aviator Way
Manchester M22 5TG
(Tel) +66 (2) 69 41 47 05
(Fax) +66 (2) 69 41 476
[email protected]
TPP Operation Co. Ltd.
Kommunikationstechnik
41/5 Mooban Tarinee
Boromrajchonnee Road
Talingchan
Bangkok 10170
United Arab
Emirates
United
Kingdom
(Tel) +971 (2) 55 49 411
(Fax) +971 (2) 55 49 433
[email protected]
(Tel) +44 (1252) 81 88 88 (sales)·+44
(1252) 81 88 18 (service)
(Fax) +44 (1252) 81 14 47
[email protected]
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
R&S CMU 200
Contents of Chapter 1
Contents
1 Preparation for Use............................................................................................. 1.1
Front and Rear View.........................................................................................................................1.1
Rear View ..........................................................................................................................................1.7
Putting the Instrument into Operation .........................................................................................1.10
Unpacking the Instrument ......................................................................................................1.10
Setting up the Instrument .......................................................................................................1.10
Mounting in a Rack.................................................................................................................1.11
Connecting the Instrument to the AC Supply .........................................................................1.11
Switching on the Instrument / Startup Test ............................................................................1.11
Switching off the Instrument...................................................................................................1.13
How to Ensure EMC...............................................................................................................1.13
Input Level..............................................................................................................................1.13
Connecting the CMU to the Test Setup........................................................................................1.14
Connecting a Controller..........................................................................................................1.14
Connecting an External Keyboard..........................................................................................1.16
Connecting a Monitor .............................................................................................................1.16
Connecting a Printer...............................................................................................................1.17
Synchronization with External Devices; Connection of Further Components ........................1.17
Software Update and Version Management ................................................................................1.18
R&S Remote Service Tool .....................................................................................................1.18
Remote Control of the R&S CMU 200 .........................................................................1.25
File Versions.new.........................................................................................................1.26
CMU VersionManager............................................................................................................1.27
1100.4961.62
I-1.1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
R&S CMU 200
Front and Rear View
1 Preparation for Use
This chapter describes the controls and connectors of the Universal Radio Communication Tester CMU
and gives all information that is necessary to put the instrument into operation and connect external
devices. Notes on reinstallation of the CMU software and a description of the VersionManager and the
RF user correction appear at the end of this chapter.
Caution!
Please observe the instructions of the following sections so that you cannot cause
damage to the instrument or endanger people. This is of particular importance when
you use the instrument for the first time. Also observe the general safety instructions
at the beginning of this manual.
A more detailed description of the hardware connectors and interfaces can be found in chapter 8 of the
complete operating manual. Chapter 2 of the operating manual provides an introduction to the operation
of the CMU by means of typical examples of configuration and measurement; for a description of the
operating concept refer to Chapter 3.
For remote control of the CMU refer to the general description of the SCPI commands, the instrument
model, the status reporting system, and measurement control in Chapter 5 of the operating manual.
Front and Rear View
The front panel of the CMU consists of the VGA display with the softkey area (left side) and the hardkey
area (right side, see Fig. 1-1). Brief explanations on the controls and connectors of the hardkey area and
the rear panel are to be found on the next pages. Operation by means of softkeys is described in chapter 3 of the operating manual, Manual Operation.
9 softkeys with
alternating function
ON/Standby key (p.4)
LC display with
menu example
UNIVERSAL RADIO COMMUNICATION TESTER .
9 softkeys with
alternating function
Escape key (p.4)
Keys and connectors
1100.0008.02
CMU 200
FUNCTION
MENU
SELECT
DATA
SYSTEM
CTRL
HELP
8
def
ghi
9
G/n
mV
4
5
6
M/µ B
µV
W
3
k/m
dBµV
jkl
pqr
mno
PRINT
A
abc
7
SETUP
VARIATION
DATA
DATA 1
DATA 2
1
2
stu
0
_µΩ
*.
C
yz
vwx
#
E
-
F
symb
mark
ON / OFF
ENTER
EXP/CMP
CONT/HALT
*1 D
dBm
dB
AUX 3
UNIT...
SPEECH
CONTROL
CLR
ESCAPE
INS
DEL
VOL
AUTO
INFO
RESET
AUX 1
AUX 2
AF IN
AF OUT
RF4 IN
13 dBm MAX
RF 3 OUT
RF 2
RF 1
13 dBmMAX
2 W MAX
50 W MAX
Bar with 8 hotkeys
Fig. 1-1 CMU front view
1100.4961.62
1.1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Front and Rear View
Data input
R&S CMU 200
Selection of the most important
CMU functions via menus
Loudspeaker, for
future extensions
PCMCIA interface
as an alternative:
Floppy disk drive
(option CMU-U61)
Fig. 1-2 CMU front view – hardkeys
FUNCTION
Operating manual
Preselection of the menus:
MENU SELECT
Menu selection
DATA
File manager
CTRL
For GSMxxx-MS Signalling tests:
Measurement Wizard
DATA
)
Chap. 3
Chap. 4
Operating manual
Data input:
0 ... 9
*.E
#-F
G/n mV A
M/µ µV W
Numerical input (letters for string editors)
Special characters, dec. point, hex value "E"
Spec. characters, sign change, hex value "F"
9
-9
Factor 10 /10 , unit, hex value "A"
6
-6
3
-3
)
Chap. 3
Factor 10 /10 , unit, hex value "B"
k/m dB µV
*1 dBm dB
ON / OFF
Factor 10 /10 , unit, hex value "C"
0
Factor 10 , unit, hex value "D"
Switching on/off editors/measurements
EXP/COMP
ENTER
Confirmation of entry in editors
CONT/HALT Calling/quitting editors,
measurement control
For future extensions
UNIT Ø
1100.4961.62
1.2
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Front and Rear View
System control
Variation of numeric values and
group selection in popup menus
Fig. 1-3 CMU front view – hardkeys
SYSTEM
Operating manual
System control:
HELP
SETUP
PRINT
Displays online help
Instrument settings
Initialize printing of a screenshot
VARIATION
Chap. 3
Operating manual
Value variation and group selection:
Rotary knob
Value variation in input fields and
parameters, line selection in tables, field
selection in popup menus. Press to
expand/compress tables and pull-down
lists and to confirm entries and
selections.
Cursor key
Group selection in popup menus
vertical
(vertical)
Cursor key
Group selection in popup menus
horizontal
(horizontal),
Cursor positioning in editors and
tables
1100.4961.62
)
)
Chap. 3
1.3
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Front and Rear View
R&S CMU 200
Extended editor
and instrument
control functions
Fig. 1-4 CMU front view – hardkeys
CONTROL
Operating manual
Extended control functions:
CLR
Clears the complete editor string
Õ
Deletes the character to the left of the cursor
(back space)
INS
Changes between insertion and overwriting
in the editor
DEL
Deletes the character marked by the
cursor
VOL
For future extensions
AUTO
For future extensions
INFO
System info and hardware diagnosis
RESET Resets to default values
Further Keys
ESCAPE
1100.4961.62
)
Chap. 3
Operating manual
ESCAPE
Quits popup menus, closes an editor
discarding the entries made
ON/STANDBY
Switches between operation (green LED)
and standby (orange LED)
)
Chap. 3
1.4
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Front and Rear View
For future extensions
Auxiliary input/output
AUX3
Signals from/to
speech codec
(option CMU-B52)
AF inputs and outputs
Fig. 1-5 CMU front view connectors
DATA1, DATA2
Operating manual
For future extensions
)
AUX 3 and SPEECH
AUX 3
Operating manual
Input and output for status, control, and trigger signals:
CMU 300: External trigger signal for
wired synchronization
)
Chapter 8, "Hardware connectors "
Signals from/to speech codec (option CMU-B52)
)
Chapter 8, "Hardware connectors"
SPEECH
AF connectors
Operating manual
Connectors for audio signals:
AUX1/2
Additional input/output for audio signals
that may be used in remote control (secondary audio analyzer)
AF IN/OUT
Standard input/output for the (primary)
audio analyzer
Caution:
1100.4961.62
Chapter 8, "Hardware connectors"
)
Chapter 4, "Audio
Generator and
Analyzer";
Chapter 8, "Hardware connectors"
Note the maximum permissible input levels for all
AF connectors according to the data sheet in order to prevent damage to the instrument!
1.5
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Front and Rear View
R&S CMU 200
Bidirectional RF connectors
RF 1 und RF 2
Sensitive RF input, high-level RF output
Fig. 1-6 CMU front view– connectors
RF connectors
Operating manual
Bidirectional RF connectors for various power ranges according to the data sheet.
The two LEDs above the connectors are illuminated as long
as the CMU sends signals
or is ready for reception
.
Connector with high output level and connector for sensitive
RF measurements (antennas). Power ranges according to the
data sheet. Maximum permissible input and output level according to the label on the front panel.
)
)
Chapter 8,
"Hardware
connectors "
Chapter 8,
"Hardware
connectors"
The two LEDs above the connectors are illuminated as long
as the CMU sends signals
or is ready for reception
.
Caution:
Note the maximum permissible input levels for all RF connectors according to the label on the front panel or the data sheet
in order to prevent damage to the instrument!
RF connectors may warm up very much when high RF power
is fed in!
1100.4961.62
1.6
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Rear View
Rear View
Synchronization inputs and outputs, IF interface (with option CMU-B17)
Interfaces for remote control
and peripheral equipment
Signal inputs and outputs
Fig. 1-7
Mains connector with switch
CMU rear view
Mains switch
Operating manual
)
)
Mains power switch
Mains connector
Interfaces
Chapter 1, "Connecting the instrument to the
AC supply”
Operating manual
GPIB-bus connector
(IEEE 488 / IEC 625),
Parallel interface: 25-contact
printer connector, Centronicscompatible
Connector for serial interface 1: 9contact Sub-D connector
Connector for serial interface 2: 9contact Sub-D connector
1100.4961.62
Chapter 1, "Switching on the Instrument,
Startup test"
)
Chapter 8, "Hardware Interfaces "
)
Chapt. 1, "Connecting an Output Device"
Chapter 8, "Hardware Interfaces”
)
)
Chapter 8, "Hardware Interfaces”
Chapter 8, "Hardware Interfaces”
Connector for an external VGA
monitor: 15-contact Sub-D
connector
)
Chapter 1, "Connecting a Monitor"
Chapter 8, "Hardware Interfaces”
USB connector for external
keyboard only (not for other
pointing or storage devices)
)
Chapter 1, "Connecting an External Keyboard"
Chapter. 8, "Hardware Interfaces”
1.7
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Rear View
R&S CMU 200
Inputs and outputs for reference frequency and network-specific clock frequency
Intermediate
frequency
from CMU receiver,
IF interface
Auxiliary and
service connectors,
I/Q interface
Fig. 1-8
CMU rear view – signal inputs and outputs
Intermediate frequency
Operating manual
IF3 RX CH1 (BNC connector) from CMU receiver
)
Reference frequency
Chapter 8,
"Hardware
Connectors"
Operating manual
REF IN
Input for external reference frequency
REF OUT 1
Output of reference frequency of CMU:
10 MHz or the signal of input REF IN
REF OUT 2
Output for network-specific clock
frequency
)
)
Chapter 8,
"Hardware
Connectors
Chapter 3, "RF
Connection
Control"
Caution!
Do not use open or unshielded cables in order to comply with EMC directives!
AUX, SERVICE, AUX4, extensions
Operating manual
Two 9-contact and one 15-contact SUB-D connectors:
AUX
Auxiliary connector providing a DC
voltage to supply external equipment
such as CMU-Z6
SERVICE
Service connector for RXTX board
(only for internal test purposes)
AUX4
Bidirectional input/output for digital
status, control, and trigger signal
The remaining 15-contact SUB-D connectors are
reserved for future extensions.
1100.4961.62
)
)
Chapter 8,
"Hardware
Connectors
Chapter 8,
"Hardware
Connectors
1.8
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Rear View
IF interface
Option CMU-B82
Access Board for
CDMA Sign. Units
Option CMU-B87
Message Monitor for
CDMA2000
I/Q interface
Fig. 1-9
CMU rear view – I/Q-IF inputs and outputs
I/Q-IF Interface (with option CMU-B17)
Operating manual
Four 50 Ω BNC connectors for option CMU-B17, I/Q and
IF Interface:
IF3 RX CH1 IN
RX path, IF IN
IF3 RX CH1 OUT
RX path, IF OUT
IF3 TX CH1 IN
TX path, IF IN
IF3 TX CH1 OUT
TX path, IF OUT
15-contact SUB-D connector for input and output of I/Q
signals (option CMU-B17, I/Q and IF Interface)
Chapter 4,
"Hardware
Connectors"
Chapter 8,
"Hardware
Connectors"
The SUB-D connector below IQ CH 1 is not used.
Chapter 8,
"Hardware
Connectors"
Optional interfaces for data applications
Digital I/Q connector for option R&S
CMU-B82, Access Board for CDMA
Signalling Units
Ethernet connector e.g. for option R&S CMU-B87,
Message Monitor for CDMA2000
An additional Ethernet connector can be fitted below,
e.g. for option R&S CMU-Z46, WCDMA Message
Analyzer and Recorder.
1100.4961.62
Installation
instructions for
options
Installation
instructions for
options
1.9
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Putting the Instrument into Operation
R&S CMU 200
Putting the Instrument into Operation
This section describes the basic steps to be taken when setting up the CMU for the first time.
Caution!
Please make sure to observe the instructions of the following sections so that you
cannot cause damage to the instrument or endanger people. This is of particular
importance when you use the instrument for the first time.
Unpacking the Instrument
¾ Take the instrument out of the shipping box and check whether the
items listed in the packing list (see page 3 at the beginning of this
manual) are all included.
remove protective caps
¾ Remove the two protective caps from the front and rear of the CMU
and carefully check the instrument for damage.
Should the instrument be damaged, immediately notify the forwarder who shipped the instrument to you
and keep the box and packing material.
For further transport or shipment of the CMU the original packing should be used, too. It is
recommended to keep at least the two protective caps for front and rear side in order to prevent damage
to the controls and connectors. The caps are also necessary if the CMU is transported in its transit case
that can be ordered from Rohde & Schwarz.
Setting up the Instrument
Permissible operating positions of the CMU:
• Horizontal position, standing on the feet.
•
For applications in the laboratory or on a work bench, it is recommended that the support feet on the
bottom of the instrument be extended. For the LCD display, this provides the optimum viewing angle
which typically ranges from perpendicular to the display front to approximately 30° below.
Warning!
The feet must be fully folded in or out. Only in this way can the stability of CMU be
guaranteed and reliable operation be ensured. With the feet out, the weight of other
units put onto CMU must not exceed 30 kg. The units must be secured against
slipping (e.g. by locking the feet of the unit at the top side of the enclosure).
When moving the unit with the feet out, the feet might collapse and fold in. To avoid
injuries, the unit must therefore not be moved with the feet out.
Notes:
For safe and convenient operation of the instrument note the following:
¾ Do not cover the rear and lateral ventilation holes.
¾ Note the permissible ambient temperature according to the data sheet.
¾ Avoid moisture condensation. If it occurs, the instrument must be wiped dry before
switching on.
1100.4961.62
1.10
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Putting the Instrument into Operation
¾ Note the warm-up time of the temperature-controlled OCXO reference oscillator (Option
CMU-B11/B12), see data sheet.
Mounting in a Rack
Using the adapter ZZA-411 (order number 1096.3283.00) the instrument can be mounted in 19" racks
according to the mounting instructions supplied with the rack adapter.
Note:
For convenient operation of the instrument note the following:
¾ Allow for sufficient air supply in the rack.
¾ Make sure that there is sufficient space between the ventilation holes and the rack
casing.
Connecting the Instrument to the AC Supply
Caution!
After moisture condensation, allow the instrument to dry before switching on.
Note the permissible ambient temperature according to the data sheet.
Do not cover the lateral and rear ventilation holes.
The CMU may be connected to one-phase AC supplies with nominal voltages ranging from 100 V to
240 V and nominal frequencies ranging from 50 Hz to 400 Hz (see inscription on the rear panel and data
sheet). Depending on the options installed, the power consumption ranges from 120 W to 230 W.
Note:
The CMU is automatically adapted to the AC supply voltage applied. External
switchover or adaptation of the fuses are not necessary.
For the mains connection use the supplied mains connector.
o
I
Mains
connector As the instrument is designed according to the regulations for safety class
EN61010, it must be connected to a grounded power outlet.
Switching on the Instrument / Startup Test
The CMU can be switched on using the mains switch at the rear of the
instrument and the ON/STANDBY key at the bottom left of the instrument
front.
o
I
Mains
switch
1100.4961.62
The mains switch can be set to two positions:
0
The 0 position implies an all-pole disconnection of the instrument
from the mains.
I
In the I position, the instrument is in standby mode or in operation,
depending on the position of the ON/STANDBY key at the front of
the instrument.
1.11
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
STANDBY
ON
Putting the Instrument into Operation
R&S CMU 200
The ON/STANDBY key activates two different operating modes indicated
by colored LEDs:
Standby
ON/
STANDBY
key
Start procedure
Only the OCXO reference frequency oscillator (Option CMUB11/B12), if installed, is supplied with operating voltage. The
orange LED (STANDBY) on the right is illuminated.
Operation In this operating mode, all modules of the instrument are
supplied with operating voltage. The green LED (ON) on the
left is illuminated.
¾ To switch on the CMU set the mains switch to the position I.
The CMU enters standby mode.
• Set the CMU to operating mode by pressing the ON/STANDBY key
once.
Caution!
When switching on the CMU, no disk should be inserted in the
drive; otherwise, one of the actions stored on the flash disk will
be performed.
Startup menu
After activation of the operating mode, the startup menu appears for a few
seconds. While it is displayed the CMU performs a startup test.
Displays in startup
menu
The display windows of the startup menu provide information on
• The startup procedure (Process)
• Instrument model, serial number and version of the CMU base software
(Info).
• Installed hardware and software options and equipment (Options).
Available software options are listed with their version numbers.
• Progress of the startup procedure (Startup bar graph).
After terminating the startup procedure, the instrument changes to the last
main menu or graphical measurement menu of the previous session.
1100.4961.62
1.12
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Putting the Instrument into Operation
Switching off the Instrument
In order not to lose any settings that have been made, proceed in the
following order to switch off the CMU:
Remove any storage medium from the PCMCIA interface or floppy disk
drive.
Shortly press ON/STANDBY to initiate the shutdown process and save
the current data to the internal hard disk.
Wait until the shutdown process has been terminated before setting the
mains switch at the rear to the 0 position.
o
I
Note:
Instruments equipped with a Front Module controller FMR 6
display the message Shutdown in Progress after the
ON/STANDBY key has been pressed. Keeping ON/STANDBY
pressed for about 4 s on those instruments initiates a
hardware shutdown where data may be lost.
How to Ensure EMC
In order to avoid electromagnetic interference, the instrument may only be operated when it is closed
and with all shielding covers fitted.
REF OUT 1 and REF OUT 2: Use doubleshielded cables and match signal with 50 Ω in order to
comply with EMC directives!
Input Level
Caution!
-
1100.4961.62
In order to prevent damage to the instrument note the maximum permissible input
levels at the AF inputs AF IN and AUX 1 as well as for the RF inputs RF 1, RF 2 and
RF 4 IN at the front of the instrument.
1.13
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-2
Connecting the CMU to the Test Setup
R&S CMU 200
Connecting the CMU to the Test Setup
Warning:
Connect external devices and peripherals only when the instrument is
switched off or in STANDBY mode. Otherwise, future errors cannot be
excluded.
Connecting a Controller
The CMU can be connected to an external controller via the GPIB bus (IEEE bus according to standard
IEEE 488; throughout this documentation we will primarily use the term GPIB bus which is also used in
the operating menus and in the SCPI command syntax) or via serial interface:
Connection via GPIB
bus
The CMU is connected to the GPIB interface of the controller via the GPIB
bus connector (IEEE 488 / IEC 625) at the rear of the instrument and a
shielded cable. The technical specifications of the GPIB interface are listed in
section Hardware Interfaces in Chapter 8 of the operating manual.
IEEE 488
625
GPIB Bus
Configuration
In the default configuration the CMU accepts commands from either the GPIB
or COM 1 interface. The parameters for GPIB bus control of the CMU are set
in the Remote tab of the Setup popup menu (in the following abbreviated by
Setup – Remote, see also Chapter 4 of the operating manual, Settings for
Remote Control).
¾ To open the Setup - Remote menu, press the SETUP key at the front of
the instrument and activate the Remote hotkey at the lower edge of the
screen.
¾
1100.4961.62
Use the rotary knob to move the focus onto the SCPI Connection section
of the Setup table. If necessary, press the rotary knob or the ON/OFF key
to expand the parameters in the table (see Chapter 3 of the operating
manual).
1.14
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Connecting the CMU to the Test Setup
¾
In the Port table row select either GPIB + Com 1 or GPIB bus interface
for transmission.
The bus address is factory-set to 20. It can be changed in the Primary
Address input field.
Connection via serial
interface
COM 1
The CMU can be connected to the serial interface of a controller via one of
the serial interfaces COM 1 or COM 2 and a so-called null-modem cable. The
pin assignment and wiring of a null-modem cable are described in section
Handshake of Chapter 8 of the operating manual. The technical
specifications of the serial (RS-232-C) interface are also discussed in
Chapter 8 (refer to section Hardware Interfaces).
Either a 25-pin or a 9-pin connector can be used on the controller side. It may
be necessary to use an appropriate adapter (see Chapter 8, Hardware
Interfaces).
Selection
In the default configuration the CMU accepts commands from either the GPIB
or COM 1 interface. The COM 2 interface must be selected explicitly.
¾ Proceed as described above to activate the Remote tab of the Setup
menu.
¾
Configuration
In the Port table row, select GPIB + Com 1 or COM 1 or COM 2 to
activate one of the RS-232 interfaces for data transfer.
After selection of a serial interface, the transmission parameters must be set
to comply with the parameters of the addressed device. This is done in the
Comm. (communications) tab of the Setup menu:
¾ To open the Setup – Comm. tab press the SETUP key at the front of the
instrument and activate the Comm. hotkey at the lower edge of the
screen.
¾ In the table section corresponding to the selected COM port check the
settings for the Baudrate, Data Bits, Parity, and Protocol.
1100.4961.62
1.15
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Connecting the CMU to the Test Setup
R&S CMU 200
Connecting an External Keyboard
USB
An external PC keyboard to the CMU can be connected to the USB
connector at the rear of the instrument. An external keyboard facilitates the
input of numbers and texts.
For the interface description see section Hardware Interfaces in Chapter 8 of
the operating manual.
The key assignment can be changed in the Misc. tab of the Setup menu:
Language assignment
¾ To open the Setup – Misc. tab press the SETUP key at the front of the
instrument and activate the Misc. hotkey at the lower edge of the screen.
¾ Use the rotary knob to select Keyboard and set the desired language (US
or German).
Connecting a Monitor
MONITOR
An external VGA monitor can be connected to the 15-contact Sub-D
connector at the rear of the instrument.
For the interface description see section Hardware Interfaces in Chapter 8 of
the operating manual.
1100.4961.62
1.16
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Connecting the CMU to the Test Setup
Connecting a Printer
A printer can be connected via the 25-contact parallel interface LPT at the
rear of the instrument (recommended) or one of the serial interfaces COM 1
or COM 2. For the interface description see section Hardware Interfaces in
Chapter 8 of the operating manual.
LPT
The printer type and port must be set in the Print tab of the Setup menu:
¾ To open the Setup – Print tab press the SETUP key at the front of the
instrument and activate the Print hotkey at the lower edge of the screen.
¾ In the Printer section set the printer type and port (COM 1 or COM 2 for
the serial (RS-232) ports; LPT 1 for the parallel printer port).
It is recommended to connect the output device to the parallel interface LPT,
if possible: With this selection, configuration of the interface is not necessary;
besides, the serial connectors may be used for GPIB bus etc.
Synchronization with External Devices; Connection of Further
Components
REF IN
REF OUT 1
REF OUT 2
The three BNC female connectors REF IN, REF OUT 1, REF OUT 2 are
provided for synchronization of the CMU with external devices.
1100.4961.62
1.17
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Software Update and Version Management
R&S CMU 200
Software Update and Version Management
Your CMU was delivered with the latest software and firmware version available. New firmware can be
easily installed via the floppy disk drive (option CMU-U61) or the PCMCIA interface on the front of the
instrument.
Note:
When copying an installation version to a PCMCIA card or floppy, ensure that all folders
containing a base system version or network option (the lowest-level folders in Fig. 1-9
below) are in the root directory. Otherwise the R&S CMU will not be able to detect the
firmware and start the installation. If a Versions.new text file (see section File Versions.new
on p. 1.26 ff.) is used, it must also be in the root directory of the external storage medium.
New software options must be enabled by means of a key code entered in the Setup –
Options menu (see Chapter 4 of the operating manual). This is necessary only once; all
options remain enabled after a software update.
Installation of new firmware versions and the use of different applications and versions on the same
instrument is made easier by the following tools:
• The R&S Remote Service Tool (see p. 1.18 ff.) transfers software versions to the instrument.
•
The VersionManager (see p. 1.27 ff.) is designed to manage different software versions stored on
the instrument.
Installation instructions are also given in Chapter 1 of the operating manuals for the individual software
options.
R&S Remote Service Tool
The R&S Remote Service Tool organizes the exchange of data between the R&S CMU and an external
PC or laptop, in particular to:
• Copy software versions and install them on the R&S CMU.
•
Copy or move data files (e.g. screenshots created with the Print menu of model R&S CMU).
•
Send remote control commands to the instrument.
The tool is available for download on the CMU Customer Web (https://gloris.rohdeschwarz.com/gloris/1cmp/cmucustomer/index.html). It consists of a single *.exe file which can be copied
to any directory. When the executable file is started (double-clicked), the R&S Remote Service Tool
opens the following main application window.
1100.4961.62
1.18
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Software Update and Version Management
Fig. 1-9 Remote Service Tool main screen (example)
Connecting the
R&S CMU
The R&S Remote Service Tool can communicate with the R&S CMU via the
GPIB (IEEE 488) or a RS-232 interface. To ensure fast transmission, it is
recommended to use the GPIB interface, connecting the GPIB cable to the
IEEE 488 / IEC 625 connector on the rear panel of the instrument.
Note:
The GPIB settings of the Remote Service Tool and of the R&S
CMU must be the same. Refer to section Connecting a Controller
on p. 1.14 to learn how to configure the R&S CMU’s GPIB
settings.
1. Connect the GPIB cable to the IEEE 488 / IEC 625 connector on the rear
panel of the instrument.
2. Start the Remote Service Tool.
3. Click the Options menu and make sure that Use GPIB is selected.
4. Click Options – GPIB Options and check that the Board Index and Primary
Address settings are equal to the R&S CMU configuration (CMU default
settings: board index GPIB0, primary address 20).
Installing software
versions
To copy a new software version to the CMU…
1. Switch on and start up your R&S CMU.
2. Select Applications – Version Copy from the menu bar of the Remote
Service Tool.
3. In the Version directory of the main application window, select the folder
from where you want to copy your software version and click Next >>>.
1100.4961.62
1.19
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Software Update and Version Management
R&S CMU 200
4. Select the software version you wish to install and click Start >>>.
The software version is copied to the internal drive C:\INTERNAL\INSTALL of
your R&S CMU. In addition, a text file named Versions.new (see section File
Versions.new on p. 1.26 ff.) is generated and copied to the same directory.
With default installation options (see figure above), the following happens after
the file transfer is completed:
• The CMU is rebooted and the new software version is installed and
activated.
•
The Remote Service Tool is closed automatically.
Old software versions are not affected. You can delete or activate an old
software version using the Version Manager (see p. 1.27 ff.).
Listing and
modifying software
versions
1100.4961.62
The Remote Service Tool can not only install firmware versions but also display
and modify the installed firmware configurations.
To list the firmware configurations installed on your CMU…
¾ Click Application – List Software.
1.20
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Software Update and Version Management
The list of installed versions has a tree structure. Each expandable node
contains a software configuration consisting of one base system version and
one or more network options. The active configuration is marked as (active)
and also displayed in the title bar of the Remote Service Tool. You can use the
controls on the left side to do the following:
• Select a configuration in the list and click Activate to label the configuration
active.
•
Select a configuration in the list which is not the active configuration and
click Delete to label the configuration deleted. Repeat this for all
configurations you wish to delete.
Labeled configurations are not deleted immediately. You can simply Restore
any configuration that you labeled inadvertently.
¾ Click Perform Actions to activate and/or delete the labeled configurations.
The labeled configurations are written to the Versions.new text file (see section
File Versions.new on p. 1.26 ff.) which is copied to the internal drive
C:\INTERNAL\INSTALL of your R&S CMU. In the default configuration where
Force device reboot is enabled, the R&S CMU is rebooted immediately so that
the VersionManager can activate and delete the labeled configurations.
Tip:
Copying files
Disable Force device reboot in case you wish to postpone the
actions until next time you switch on your instrument.
To transfer a file from the CMU to the PC or vice versa…
1. Switch on and start up your R&S CMU.
2. Select Applications – File Transfer from the menu bar of the Remote
Service Tool.
The main application window shows the directories and files on your PC and on
the INTERNAL directory of the CMU’s hard disk.
1100.4961.62
1.21
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Software Update and Version Management
R&S CMU 200
3. Select a directory, a file or several files and use the commands in the
FileCtrl menu to initiate the file transfer. You can also right-click the file list
to open the equivalent context menu.
Extracting
screenshots
A screenshot transferred by means of the Remote Service Tool can be viewed
and copied to the clipboard so that you can use it in another application.
To generate, transfer and further process a screenshot…
1. Press the PRINT button on the front panel of the CMU to open the Print
dialog, select Internal WMF as a destination and specify a file name
<file>.wmf for the generated image file (without adding a path).
2. Press OK to write the file to the INTERNAL\USERDATA\PRINT directory of
the CMU.
3. Proceed as described above to transfer the file <file>.wmf from the CMU to
your PC.
4. Double-click the transferred file (alternative: select the file and press
Enter).
The Remote Service Tool acts as a viewer for the file:
5. Right-click to open a context menu and either copy or close the file.
Remote control of
the R&S CMU
You can use the Remote Service Tool to transfer remote control commands or
command scripts to be executed on the R&S CMU.
To transfer a single command or command sequence…
1. Click Applications – Command to activate the remote control screen.
1100.4961.62
1.22
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Software Update and Version Management
2. Select the appropriate function group in the Secondary address mapping
panel.
3. Enter a command in the Enter remote command… input field and press
Enter.
4. Repeat steps 2 and 3 for all commands you wish to execute.
To execute a command script…
5. Generate an ASCII text file of remote control commands, either manually
or by saving a previously transferred command sequence (Save… button
in the remote control screen.
6. In the remote control screen, click Load… and open the file.
The script is transferred and executed automatically. The remote control
screen provides further control elements to make the command transfer more
convenient; see section Remote Control of the R&S CMU on p. 1.25 ff.
Table 1 Overview of R&S Remote Service Tool functions
Menu
Command
Function
File
Close
Close the Remote Service Tool.
Application
Version Copy
Copy a software version to the R&S CMU. See the application
example Installing software versions above.
List Software
Display of all software configurations installed on the R&S CMU
and activate and/or delete configurations. See the application
example Listing and modifying software versions above.
Command
Transfer of remote control commands or command scripts to be
executed on the R&S CMU. This command activates an
additional Cmd Ctrl menu to generate log files and customize the
screen. See application example Transferring remote control
commands above and section Remote Control of the R&S CMU
on p. 1.25 ff.
File Transfer
Transfer of data between a PC and the R&S CMU. This
command activates an additional FileCtrl menu to create
directories, copy or delete files. See application examples
Copying files and Extracting screenshots above.
Error Reports
For future extensions
1100.4961.62
1.23
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Software Update and Version Management
R&S CMU 200
Menu
Command
Function
Options
Use GPIB
Use the GPIB bus for communication with the R&S CMU.
USE RS232
Use the RS232 bus for communication with the R&S CMU.
Note: This communication mode is recommended.
Note: Use the RS 232 Options quoted below if you choose this
communication mode.
GPIB Options
Change GPIB connection parameters. The default settings for the
R&S CMU are:
Board Index:
Primary Address:
0
20
Note: The GPIB settings of the Remote Service Tool and of the
R&S CMU must be the same. Refer to section Connecting a
Controller on p. 1.14 to learn how to configure the R&S CMU’s
GPIB settings.
RS232 Options
Change RS232 transmission parameters. The following settings
ensure a reliable connection:
Baud Rate:
Data Bits:
Stop Bits:
Parity:
Protocol:
115200
8
1
None
CtsRts (do not change!)
Note: The RS232 settings of the Remote Service Tool and of the
R&S CMU must be the same. Refer to section Connecting a
Controller on p. 1.14 to learn how to configure the R&S CMU’s
RS232 settings. Should you experience any problems with the
data transfer, first check and possibly exchange the connecting
cable.
Help
1100.4961.62
Device Clear
Clear the screen.
Go to Local
Exit remote control mode and return to manual operation.
Device Reboot
Reboot the R&S CMU.
About
Shows an information box with the current version of the Remote
Service Tool.
1.24
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Software Update and Version Management
Remote Control of the R&S CMU
The remote control screen transfers remote control commands or command scripts to be executed on
the R&S CMU; see application example Remote control of the R&S CMU on p. 1.22. It is opened by
clicking Application – Command.
Fig. 1-10
Remote control screen
The commands to be executed are entered in the Enter remote command… input field; the responses of
the R&S CMU and possible error messages are displayed below. Besides the remote control screen
provides the following control elements:
Execute all
commands
Execute all commands entered since the Remote Service Tool was started or
since the list was cleared. The complete command list appears in a pull-down
list associated with the Enter remote command… input field.
Report Display /
Report File
Display the remote report on the R&S CMU’s remote screen and create a
report file. These functions are identical with the Report Display and Report
File hotkeys in the CMU’s remote screen.
Load / Save
Load an ASCII text file (default extension: *.lst, can be changed at will), with a
command script to be executed or save the current command list to a text file
file.
Clear
Clear the current command list.
Refresh sec.
address mapping
Refresh the list of assigned secondary addresses and function groups, e.g.
after the mapping was changed on the R&S CMU. Commands are sent to the
secondary address selected in the list.
1100.4961.62
1.25
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Software Update and Version Management
R&S CMU 200
While the remote control screen is active, an additional Cmd Ctrl menu is available:
Table 2 Overview of Cmd Ctrl menu in the Remote Service Tool
Command
Function
Filename…
Call up an Open File dialog to define the name and location of a log file containing all executed
commands and device responses. The responses can be up to 2 MByte in size, so the log file
information is often more complete than the remote report displayed on the instrument’s remote
screen.
Logging
Toggle function: Enable or disable logging.
Append File
Toggle function: If enabled, new information is appended at the end of the log file. Otherwise the log
file is overwritten at the beginning of each Remote Service Tool session.
Button Setup
Open a dialog to create command buttons, to be used as shortcuts for manual entry of frequently
used commands. The command buttons idn, opc, and Reset in Fig. 1-10 on p. 1.25 are created as
follows:
File Versions.new
The Versions.new file stores the software configurations that the R&S CMU VersionManager has to
install, delete, or activate. The following Versions.new file initiates the installation of a software
configuration containing a base system, a GSM network option package, and a IS136 package:
BASE3x60.i35
GSMS3x60.i35
IS1M3x60.i35
Automatic Install
Creating a
Versions.new file
The file is most conveniently created using the Remote Service Tool; see
application examples Installing software versions on p. 1.19 and Listing and
modifying software versions on p. 1.20. The Remote Service Tool also copies
the file to its location on the CMU’s internal hard disk (C:\INTERNAL\INSTALL)
so that it will be executed when the VersionManager is started.
Alternatively, the file can be created manually and copied to the
C:\INTERNAL\INSTALL directory or to the root directory of a PCMCIA
card/floppy disk.
Restrictions
1100.4961.62
The information in the Versions.new file must be unambiguous: Only one
software configuration with 1 base system software can be installed at once.
1.26
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Software Update and Version Management
Alternatively, the file may list several network options to be combined with an
already installed, compatible base system version.
Only one software configuration can be active, however, several configurations
can be deleted together. To avoid errors, it is recommended to use different
files for installation and deletion/activation.
Typical application
¾
Copy a Versions.new file to the root directory of a PCMCIA card containing
several installation versions and insert the card into the R&S CMU’s
PCMCIA slot.
After the instrument is booted, the VersionManager is started automatically and
installs the software packages listed in the file.
CMU VersionManager
The VersionManager is a tool designed to activate, delete, install, combine, or list different software
versions in a convenient way. Moreover, it provides information on the hardware and software
configuration of the instrument (Edit service tables, Scan disk), resets the startup settings stored in the
non volatile ram, copies information to an external storage medium (Write log files to disk, List all
versions to disk), and loads and activates user correction tables (see section Chapter 1 of the complete
operating manual).
The VersionManager is part of each CMU firmware version. It is opened automatically after the boot-up
process if the CMU detects a storage medium in its floppy disk drive/PCMCIA slot that contains an
installation version of the CMU firmware. Alternatively, it can be called up by pressing the Menu Select
key after the boot-up sequence is terminated (from the moment when the CMU display turns black until
the end of the 3-beep acoustic signal).
with floppy / PCMCIA
card or
MENU
SELECT
Fig. 1-9 VersionManager main screen (example)
The different functions of the VersionManager are activated by pressing the corresponding softkeys.
Some of them (labeled optional below) are available in a particular configuration of the hard disk only.
The upper two softkeys in both softkey bars are not assigned.
Activate other
software
(optional)
1100.4961.62
Activate other software opens a list of all firmware configurations stored on
the CMU hard disk except the current configuration. Therefore, this function
is not available if the hard disk contains only a single configuration (to
retrieve information, List software can be used instead).
1.27
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Software Update and Version Management
R&S CMU 200
Each entry in the list corresponds to a firmware configuration consisting of
exactly one CMU base software version (top level on the left side) plus a set
of associated options1 (network tests, second level). The version to be
activated is displayed in red color on top of the list. To select another version,
the list can be scrolled using the rotary knob or the cursor keys.
Activate
Activate the current firmware configuration.
Back to previous screen Close the current screen and go back to the main
screen. This option is identical in all
VersionManager submenus.
Info
Open the Info screen associated with the current
screen; see Info on p. 1.34. This option is
identical in all VersionManager submenus.
Delete software
(optional)
Delete software opens a list of all firmware configurations stored on the CMU
hard disk. The dialog can be operated as explained above; see Activate
software. The last firmware configuration can not be deleted, so this function
is not available if the hard disk contains only a single configuration.
Delete
Delete the current firmware configuration.
If the active firmware configuration is deleted, the CMU asks which of the
remaining versions shall be activated:
1 Several related options may be displayed in a single line. These combinations of options can be installed together and will be simply referred to as "options" through the
remainder of this section.
1100.4961.62
1.28
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Software Update and Version Management
Activate
Install software...
Activate the current firmware configuration.
Install software... opens a list of all firmware installation versions available on
an external storage medium (floppy disk/PCMCIA card). As explained in
Table 1-3, this function depends on the type and number of storage media
and on the number of installation versions available.
Table 1-3 Software installation with the VersionManager
Storage medium with FW
installation version2
Number of FW
installation versions
VersionManager function
Floppy
1
Install software version <version> from floppy
several
Install software from floppy
–> Open software version selection dialog (see below).
1
Install software version <version> from PC-card slot <slot_no>
several
Install software from PC-card slot <slot_no>
–> Open software version selection dialog (see below).
1 (per PC-card)
Install software version <version> from PC-card
–> Open PC-card selection dialog (see below).
several
Install software from PC-card
–> Open PC-card selection dialog (see below).
PCMCIA card
in slot 0 or 1 (right or left side)
PCMCIA card
in slot 0 and in slot 1
PC-card The PC-card selection dialog selects either PCMCIA card slot 0 (right side)
selection dialog: or slot 1 (left side) for installation.
2 Media without FW installation versions are ignored.
1100.4961.62
1.29
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Software Update and Version Management
R&S CMU 200
Install software... Select the card in slot 0 or slot 1 as an installation
medium. If the medium contains several installation
versions, the software version selection dialog is called up,
see below.
Software version The software version selection dialog lists all installation versions on the
selection dialog: current medium (floppy, PCMCIA card). The dialog can be operated as
explained above; see Activate software.
Install
Install the current firmware version.
Upgrade options: In contrast to the Activate software dialog, the software selection dialog
handles base software versions and network options separately. As a
consequence, different versions of the base software can be combined with
different options to create new firmware configurations. For example, it is
possible to update the base software without affecting the associated
network options or vice versa. Moreover, the same base software version
can be installed several times and combined with different network options
(and vice versa), so it may enter into several firmware configurations. The
following simple rules apply:
• With a new version of a network option, it is only possible to update one
of the existing configurations. The following selection dialog is
automatically skipped.
•
1100.4961.62
With a new base software version, it is possible to either update an
existing configuration or create a new one. A dialog selecting between the
two alternatives is opened:
1.30
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Software Update and Version Management
Note:
This dialog is skipped if the new base software
version is not compatible with any of the existing
configurations. An incompatible new base software
must be installed as a new base software.
Install as new base
Create a new configuration based on the base
software to be installed. The upgrade selection dialog
described below is skipped. Network options can be
assigned to this base software in a second stage of
the installation.
Select an existing configuration and replace the base
software of this version. To this end, the upgrade
selection dialog described below is opened.
If the option is checked the current VersionManager is
overwritten every time that a new base system is
installed, even if this means a downgrade of the
VersionManager version. This feature is primarily for
service purposes.
Upgrade existing v.
Force verm update
After selection of an upgrade software version compatible with one of the
configurations stored on the hard disk, the upgrade selection dialog is called
up:
Upgrade
Replace the base software version or network option selected
in the software version selection dialog.
Alternatively, if none of the configurations stored on the hard disk is
compatible with the software version selected, an error message is
displayed. E.g., for an incompatible Bluetooth version:
1100.4961.62
1.31
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Software Update and Version Management
Back to...
R&S CMU 200
Close the current screen and go back to the software version
selection dialog to select a compatible software version.
Terminating the After successful installation of each software version the CMU displays the
software update: following screen:
Install next software... Go back to the software version selection dialog to
select additional software modules to be installed in
the same VersionManager session. This function
depends on the storage media and the number of
software installation versions available; see Table 1-3
on page 1.29.
Change disks
Update the current screen after a change of the
storage medium.
Finish installation
Close the VersionManager and reboot the CMU
(remove the external disk from the disk drive). The
installed firmware configurations are then operational.
The last configuration installed is taken as the active
configuration in the subsequent measurement
session.
Note:
Notice messages after firmware updates
In most cases firmware updates don’t affect the accuracy of the
measurements. There are some exceptions where a correction procedure
must be executed in the Maintenance menu after the firmware update. The
R&S CMU displays a notice message whenever this happens. The box
contains the name of the required correction procedure and appears during
startup until the correction has been performed.
1100.4961.62
1.32
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Software Update and Version Management
Lack of disk space: Before installing the next software version, the CMU checks whether there is
enough disk space on the hard disk. If not, the following dialog is displayed:
Delete
Delete the current version and return back to the
previous screen.
List software
List software opens a list of all available firmware configurations. It is
possible to activate and delete configurations from the list; see description of
Activate software and Delete software functions above.
Firmware update after
board change(…)
This function depends on whether a user correction file named
USERCOR1.DAT is stored in the directory INTERNAL\USERCOR\ of the
internal hard disk.
• If no user correction file is available, Firmware update after board change
performs an update of the current firmware including a complete CMU
hardware detection. No external installation disk is required. The update
takes some time and should be attempted in case of problems or after a
modification of the CMU hardware configuration only (also after a
combined hardware/software exchange).
•
Edit service tables
1100.4961.62
If a user correction file is found, Firmware update after board change…
opens a submenu to activate or deactivate the RF user correction; see
section Chapter 1 of the complete operating manual.
Edit service tables calls up the Service Table Editor menu showing all
hardware modules that are possibly fitted in your instrument. For service
purposes, further information can be obtained by typing a particular board
name and board index in the two lines below the table.
1.33
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Software Update and Version Management
R&S CMU 200
Exit
Exit closes the VersionManager and resumes the CMU start-up procedure.
Write log files to disk
Write log files to disk copies all *.log files stored on the CMU hard disk to an
external storage medium (floppy or PCMCIA card). The *.log source files on
the hard disk are not deleted.
The Write log files to disk function opens a blue message box indicating the
storage capacity of the external disk needed. The *.log files can be
distributed over several disks. If no disk is available, the VersionManager
displays a warning and does not start copying.
Delete non volatile
ram
Delete non volatile ram deletes all entries stored in the non volatile ram of the
CMU. This memory contains particular settings of the last CMU session that
can be reused in the next session (e.g. the last active function group and
measurement menu, special configuration etc.).
Deleting the non volatile ram can be useful after an abnormal termination of
a CMU measurement session.
Note:
Scan disk
The settings stored in the non volatile ram can also be written to
a configuration file and reused in later sessions; see Chapter 3
of the operating manual, section Saving Configurations.
Scan disk closes the VersionManager, executes the MS Scan Disk program
and finally returns you to the VersionManager. Refer to your Scan Disk
documentation for further information.
Note:
This function is not available while a base software version
<V3.00 is active.
List all versions to
disk
List all versions to disk writes the software configurations indicated via List
software to an ASCII text file that is stored on the external disk.
Copy non volatile ram
to disk
Copy non volatile ram to disk copies the contents of the non volatile ram to
the external disk (floppy, PCMCIA).
In this way, the settings stored in the non volatile ram can be used on
another CMU.
Defragment disk
Defragment disk closes the VersionManager, executes the MS Defrag.exe
program and finally returns you to the VersionManager. Defragmenting the
hard disk is suitable to improve performance after installing and deleting
many different software versions. Refer to your Defrag.exe documentation
for further information.
Note:
This function is not available while a base software version
<V3.00 is active.
Info opens an output window displaying information on the current screen.
Separate Info windows are provided for the different VersionManager
dialogs.
Info
1100.4961.62
1.34
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Software Update and Version Management
Escape Close the Info screen and return to the previous screen.
Error and notify
message
During operation, the VersionManager can display two different types of
messages:
• Error messages indicating that an action could not be successfully
performed are displayed in yellow boxes. All error messages with
possible reasons and remedial actions are explained in Chapter 9 of the
operating manual.
•
1100.4961.62
Notify messages describing ongoing processes of the instrument are
displayed in blue boxes. These messages are self-explanatory and do not
require an action to be taken by the user.
1.35
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
R&S CMU 200
Contents of Chapter 2
Contents
2 Getting Started .................................................................................................... 2.1
A Short Tutorial on CMU Operation................................................................................................2.1
Condensed Operating Instructions...........................................................................................2.1
How to access and close menus..............................................................................................2.2
How to use dialog elements in the menus ...............................................................................2.3
Startup of the CMU ...........................................................................................................................2.4
RF Measurements.............................................................................................................................2.8
1100.4961.62
I-2.1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
R&S CMU 200
A Short Tutorial on CMU Operation
2 Getting Started
The following chapter presents a sample session with the universal radio communication tester CMU. It
is intended to provide a quick overview of the settings provided in the base system and the RF function
group. No specific device under test is required. For an introduction to mobile network tests (e.g. tests of
GSM900/1800/1900 mobile phones) please refer to the relevant operating manuals.
Before starting any measurement with the CMU, please note the instructions given in Chapter 1 for putting the instrument into operation. In this chapter and in Chapters 3 to 4 of the complete operating manual you will find detailed information on customizing the instrument and the display according to your
personal preferences.
The steps to perform are explained on the left side of each double-page together with the results obtained on the CMU screen. On the right side, additional information is given. We also point out alternative settings and related measurements which could not be reported in detail.
For a systematic explanation of all menus, functions and parameters and background information refer
to the reference part in Chapter 4 of the operating manual.
A Short Tutorial on CMU Operation
The principles of manual operation – controls, operating menus, dialog elements and measurement
control – are discussed in Chapter 3 of the operating manual. Below we list some essentials for first
users:
Condensed Operating Instructions
1. Press the RESET key on the front panel to set the instrument to the default state before you configure a new measurement.
2. Press ENTER to confirm selections, even if No or Yes is displayed.
3. The MENU SELECT front panel key can be pressed in any state of the unit. A large popup menu is
then displayed in which the function group (network etc.), signalling mode, and measurement
menus can be selected. Activate by pressing ENTER.
4. A front-panel LED indicates which of the RF connectors is configured as output. In the menu, the RF
generator can be activated or deactivated with ON/OFF (green/red). The front-panel LED goes out if
the generator is in the OFF position.
5. A front-panel LED indicates which of the RF connectors is configured as input. In the menu, the
measurement can be controlled via the ON/OFF and CONT/HALT keys (ON (green), OFF (red) and
HLT (yellow) states). In the OFF state, the LED goes out.
6. The SETUP hardkey allows to make static, measurement-independent default settings such as
Remote or Time, to check which options are installed and to activate new software options.
7. The softkeys to the right of the menus are used to change the hotkeys across the bottom and their
functions. Pressing the Menus softkey (bottom right) allows a fast switchover between related
menus using the hotkeys.
1100.4961.62
2.1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
A Short Tutorial on CMU Operation
R&S CMU 200
How to access and close menus
A startup menu is displayed automatically when the CMU is switched
on.
Some general configuration and selection menus can be opened via the
MENU SELECT, RESET, INFO, PRINT, HELP or SETUP keys on the
front panel.
SETUP
The hotkeys displayed across the bottom of a main menu or graphical
measurement menu are used to switch over between different main
menus or graphical measurement menus. Tabs in popup menus are
also accessible via hotkeys.
The Connect. Control softkey (always at the top right) is available in all
measurement menus. This softkey opens a popup menu defining the
input and output connectors, the external attenuation, the reference
frequency as well as many network-specific settings.
In the Signalling test modes of many network options, the Connection
Control menu is also used to set up and terminate a connection between the CMU and the DUT.
The Connection Control menu also contains the input path and the trigger settings for the current function group and signalling state.
If a special configuration menu exists for a measurement or for a generator the corresponding softkey is marked with a yellow arrow. The
configuration menu is opened by pressing the softkey twice.
All CMU popup menus can be closed with the ESCAPE key.
ESCAPE
Main menus and graphical measurement menus are closed on switching to another main or graphical measurement menu.
1100.4961.62
2.2
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
A Short Tutorial on CMU Operation
How to use dialog elements in the menus
The dialog elements assigned to a softkey are selected by pressing the
softkey.
Different input fields can be selected by means of the 4 cursor keys
(blue frame shows active input field).
One of several elements in a list or toggle switch can be selected with
the rotary knob.
Numeric values can be either incremented/decremented using the rotary knob or entered via the numeric keypad or an external keyboard.
For a comprehensive introduction to manual operation of the CMU refer to Chapter 3 of the operating
manual.
1100.4961.62
2.3
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Startup of the CMU
R&S CMU 200
Startup of the CMU
This section describes how to customize the CMU and perform simple RF measurements. As a prerequisite for starting the session, the instrument must be correctly set up and connected to the AC power
supply as described in Chapter 1.
Step 1
o
I
¾ Switch on the CMU using the mains
switch at the rear. c
¾ Check the operating mode of the instrument at the ON/STANDBY key on the
front panel. If the CMU is in standby
mode, press the ON/STANDBY key. d
Step 2
The CMU is booted and after a short while
displays the startup menu. This menu is
usually closed as soon as the instrument
software is loaded and the startup test is
finished. e
¾ Press the Wait hotkey to prevent the
instrument from switching to another
menu. f
The Wait hotkey changes to Cont. with the
additional message Change to last menu
displayed on top.
¾ Press the Cont. hotkey to resume the
startup process.
Step 3
¾ Press the RESET key to open the Reset
popup menu.
RESET
¾ Proceed as described in Chapter 4 of the
operating manual, section Reset of Instrument Settings, to expand the tree of
function groups.
¾ Select the function groups Base and RF
to be reset (the corresponding nodes
must be black).
¾ Use the cursor keys to activate the Reset
button and press ENTER.
¾ In the popup window opened (Are you
sure?), select Yes to confirm the instrument reset.
The CMU indicates that it performs a partial
reset of the two selected function groups and
is then ready to carry out the following steps.
The Reset popup menu is closed automatically.
1100.4961.62
2.4
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Startup of the CMU
Additional Information...
Alternative Settings
and Measurements
... on Step 1
c Mains switch on the rear panel
)
When the mains switch at the rear is set to the O position, the
complete instrument is disconnected from the power supply.
When the mains power switch is set to the I position, the instrument is in standby mode or in operation, depending on the
position of the ON/STANDBY key on the front panel.
d ON/STANDBY key on the front panel
The CMU is automatically set to
the AC supply voltage and frequency applied. Note the permissible ranges of AC voltages and
frequencies indicated at the rear
of the instrument and in the data
sheet.
)
The ON/STANDBY key at the front of the instrument determines whether the instrument is in standby mode or in operation.
Standby mode:
Only the OCXO reference frequency oscillator (option CMUB11/B12), if installed, is supplied with operating voltage. The
orange LED (STANDBY) is illuminated.
Chapter 1
Chapter 1
The behavior of the CMU when it
is switched off depends on the
Front Module controller type installed.
Operation:
The green LED (ON) is illuminated and all modules of the instrument are supplied with operating voltage.
... on Step 2
e Startup menu
The startup menu displays the following information:
• The startup procedure (Process)
• Instrument model, serial number and version of the CMU
base software (Info).
• Installed hardware and software options and equipment
(Options). Available software options are listed with their
version numbers.
)
Chapter 4 of the operating
manual
The Default hotkey can be used
to load the factory default settings
for all function groups. Settings
made and stored in the previous
session are overwritten.
• Progress of the startup procedure (Startup bar graph).
f Wait hotkey
By default the CMU switches to the last main menu of the
previous session after terminating the startup process. This is
convenient if an interrupted session is to be resumed or if the
instrument is generally used in a definite operating mode.
On the other hand, the Wait function can be used to access
the configuration menus which can be opened by means of
the front panel keys before the actual measurement is
started.
While the Wait hotkey is active, a reset of the instrument is
not possible.
1100.4961.62
The CMU’s user interface has
been optimized with the aim of
facilitating fast and easy switchover between the menus and
measurement modes. This includes the general configurations
which can be accessed from any
measurement menu.
The most important selection and
configuration menus such as Reset, Setup, Menu Select etc.are
directly accessible via front panel
keys.
2.5
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Startup of the CMU
R&S CMU 200
Step 4
¾ Press the SETUP key to access general
device settings.
SETUP
¾ Press the Time hotkey to switch over to
the Time tab of the Setup menu. c
Step 5
The Time tab of the Setup menu displays the
current time zone, time and date. d
¾ Use the rotary knob to move the focus
onto the Time section of the Setup table.
If necessary, press the rotary knob or the
ON/OFF key to expand the parameters in
the table (see Chapter 3 of the operating
manual).
¾ Move to one of the input fields associated
to the Time parameter, select with
ENTER and use the rotary knob or the
numeric keypad to correct the settings for
the current time. Hours, minutes and
seconds can be edited separately.
¾ Press ENTER to confirm the entries and
quit the input fields.
¾ Move to Zone select field, activate with
ENTER, and use the rotary knob to
choose your own time zone.
¾ In the same way, activate the Format
select field and use the rotary knob to
switch over between European and North
American time conventions.
1100.4961.62
2.6
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
Startup of the CMU
Additional Information...
Alternative Settings
and Measurements
... on Step 4
c Softkeys and hotkeys
Softkeys and hotkeys are activated by pressing the associated keys on both sides and across the bottom of the display.
The general purpose of softkeys is to provide settings, control
the generator and the measurements. Hotkeys are used to
switch over between different menus and different tabs belonging to a popup menu.
)
Chapter 3 of the operating
manual
... on Step 5
d Setup menu
)
The Setup menu comprises several tabs providing general instrument settings. It is advisable to check and adjust the factory settings when you operate the CMU for the first time.
To switch over between the tabs of the setup menu use the
hotkeys displayed at the bottom of the display.
1100.4961.62
Chapter 4 of the operating
manual
The different types of menus and
control elements of the graphical
user interface is explained in
Chapter 3 of the operating manual. In the same chapter you can
find a short tutorial on the entry of
numbers and characters.
2.7
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
RF Measurements
R&S CMU 200
RF Measurements
In the RF function group, a continuous or pulsed RF signal can be generated and a RF signal with definite frequency characteristics can be analyzed. The signal level can be plotted in oscillographical
(Power) or spectral (Spectrum) representation.
Step 1
MENU
SELECT
¾ Press the Menu Select key to open the
Menu Select menu.c
¾ Use the cursor keys and the rotary knob
to select the RF function group in the
left half of the Selection table.
¾ In the right half of the table, select the
Analyzer/Generator menu.
¾ Press the Enter key to activate the
measurement selected and open the
RF Analyzer/Generator menu.
Step 2
In
the
Settings
table
the
Analyzer/Generator menu indicates the parameters of the signal generated and those
of the signal received and analyzed. d
At present, all parameters have been reset
to factory default values. Different softkey/hotkey combinations and popup menus
are provided to change the settings. Userdefined parameters will be saved for later
sessions when the CMU is switched off.
The Power output field in the Analyzer/Generator menu shows an invalid
result ("---") because at present no RF
input signal is applied to the CMU.
1100.4961.62
2.8
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
RF Measurements
Additional Information...
Alternative Settings
and Measurements
... on Step 1
c Menu Select menu
)
The Menu Select menu shows all function groups installed on
your CMU. If a function group is selected the available test
modes and measurement menus are indicated. Function
groups representing digital network tests (such as
GSM400/850/900/1800/1900-MS) are generally subdivided in
the two test modes Non Signalling and Signalling, each containing a number of measurement menus.
The RF function group is available on any CMU regardless of
the software options purchased. It comprises the three measurement menus Analyzer/Generator, Power and Spectrum.
All three measurement menus are directly accessible from
the Menu Select menu.
Chapter 4 of the operating
manual
For digital network tests refer to
the relevant operating manuals.
e.g. GSM400/850/900/1800/1900MS.
... on Step 2
d Analyzer/Generator menu
The Analyzer/Generator menu contains several softkeys to
•
Control the RF signals received and analyzed (Analyzer
Level, Analyzer Settings)
•
Control the RF signals generated (Generator)
Defining a level and frequency via the Generator softkey and
the associated hotkeys implies that a continuous signal (CW)
with this level and frequency is generated.
The RF Max. Level defined via Analyzer Level, however, denotes the maximum input power which can be measured.
This is identical with the upper edge of the Power diagram
(see below). The permissible range of Max. Level depends on
the input connector and external attenuation used (see section Analyzer Settings in Chapter 4).
)
Chapter 4 of the operating
manual
The Generator softkey provides
the most important settings of the
Generator tab of the Connection
Control menu.
The Analyzer Level and Analyzer
Settings softkeys correspond to
the Analyzer tab of the Connection Control menu.
Defining a (center) Analyzer Settings – Frequency implies
that only signals around this frequency are analyzed.
The Analyzer Settings – RBW hotkey defines the resolution
bandwidth of the analyzer.
e The status of the Analyzer Power measurement is shown in
the corresponding softkey. For ongoing measurements, the
result in the Power output field is constantly updated.
At present no input signal is available so that the Power output field shows an invalid result “– – –“
Once the softkey is selected, the Analyzer Power measurement can be switched off and on by means of the ON/OFF
key. In contrast, the CONT/HALT toggle key halts the measurement after the next valid result has been obtained.
1100.4961.62
)
Ch. 4 and Ch. 5
The options for the measurement
status are ON, OFF, or HLT. The
HLT state is reached after the end
of a single shot measurement
(see the section about measurement control in Chapter 5 of the
operating manual).
2.9
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
RF Measurements
R&S CMU 200
Step 3
¾ Press the Connect. Control softkey and
use the Generator hotkey to open the
Generator tab. c
The Generator tab controls the RF generator and defines the Frequency and Modulation of the generated RF signal.
¾ Select the Generator softkey by pressing once.
¾ Press the ON/OFF key to switch the RF
generator on. e
¾ Set the generator frequency equal to the
default frequency of the RF analyzer
frequency as shown in the figure.
¾ Press the RF
hotkey to open the tab
defining the signal connectors and external attenuation.
¾ Select RF 2 as output connector, RF 4
IN as input connector. Do not define any
external attenuation (all values equal to
0.0 dB).
Two yellow LEDs on the front panel indicate the input and output connectors selected.
¾ Use a coax cable to connect RF 2 to RF
4 IN.
¾ Press the ESCAPE key to close the
popup menu and return to the RF Analyzer/Generator main menu.
The RF level measured is now indicated
next to the Analyzer Power softkey. Due to
the loss in the signal path it should be
slightly below the generator power selected. d
¾ Reopen the Connection Control menu
and press the Generator softkey twice.
The table-oriented version of the Generator
tab is opened.
¾ Press ON/OFF to expand the parameter
tree, use the rotary knob to select the
Ramping parameter, press Enter and
use the rotary knob again to switch the
power ramping ON.
Now the generator transmits a pulsed (instead of a continuous) signal.
¾ Press the Connect. Control softkey
again or the ESCAPE key to close the
popup menu.
1100.4961.62
2.10
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
RF Measurements
Additional Information...
Alternative Settings
and Measurements
... on Step 3
c RF connectors
The RF Connection Control menu configures the input and
output connectors in the RF function group. The four connectors on the front panel differ by their permissible range of input and output powers (see Chapter 4 of the operating manual and data sheet). The values quoted on the left side are
compatible with the rated specifications.
d External attenuation
An external attenuation can be reported to the CMU in order
to compensate for known losses between the signal source
and the device under test or the analyzer.
In our example, the (positive) difference between the analyzer
power measured and the generator power can be reported as
an external output attenuation at RF 2. The RF generator increases its level to maintain the commanded power of
–27 dBm at the analyzer. The nominal generator power set in
the RF level field is thus measured and indicated next to the
Analyzer Power softkey.
)
Chapter 4 of the operating
manual
Settings made in the Connect.
Control menus apply to the entire
function group RF Non Signalling.
)
Chapter 4 of the operating
manual
Note that an external attenuation
reported to the CMU shifts the
nominal permissible ranges of
input and output levels.
Note: RF User Correction
In addition to the static external attenuation settings, the
CMU provides systematic, frequency and leveldependent correction mechanisms of the generated and
measured RF power:
•
In many function groups (e.g. the present RF group)
a frequency-dependent attenuation can be defined
after pressing Ext. Att. Output or Ext. Att. Input twice.
•
Global, frequency and level-dependent correction
tables can be loaded using the VersionManager; see
section RF User Correction in Chapter 1 of the complete R&S CMU operating manual.
1100.4961.62
2.11
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
RF Measurements
R&S CMU 200
Step 4
¾ Press the Power hotkey to switch over
to the graphical menu Power.
The Power menu shows the RF signal
power measured as a function of time at a
particular frequency and resolution bandwidth. An appropriate trigger condition
must be selected to obtain a stable display.
c
Settings (default settings or the ones made
in the Analyzer/Generator menu) and scalar results are displayed in two parameter
lines above the diagram.
Various tools allowing to take a closer look
at the measurement results are provided in
the graphical measurement menu. d
¾ Press the Marker/Display softkey twice
and vary the Time Scale to display several pulses in the diagram.
¾ Press the Analyzer Settings softkey and
vary the resolution bandwidth (hotkey
RBW). e
¾ Press the Menu softkey to display the
hotkeys used to change over to the
other measurement menus.
¾ Press the Spectrum hotkey to switch
over to the graphical menu Spectrum.
Step 5
The Spectrum menu shows the signal
power in spectral representation, i.e. as a
function of the frequency.
The settings and results displayed in the
two parameter lines above the diagram are
analogous to the ones shown in the Power
menu.
¾ Press the Marker softkey and use the
R to Pk and the Cnt to R hotkeys to center the diagram. f
¾ Press the Analyzer Settings softkey to
scale the diagram and adjust the resolution bandwidth.
¾ To close your session set the CMU to
standby mode using the power switch
on the front panel or use the mains
switch at the rear.
1100.4961.62
2.12
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
R&S CMU 200
RF Measurements
Additional Information...
Alternative Settings
and Measurements
... on Step 4
c Trigger mode
The trigger mode is set in the Analyzer tab of the Connection
Control menu or via the Trigger softkey in the graphical
measurement menus. With the default setting Free Run the
measurement is not synchronized to the frequency of the incoming pulses: The trace is permanently shifted in horizontal
direction.
To show a signal consisting of rectangular pulses (bursts) it is
recommended to trigger by either the rising or falling edge of
the IF power.
d Markers
Markers are a graphical tool used to locate points on a trace
and read out their coordinates. A reference marker and two
delta markers may be defined in the Power menu.
The reference marker
measures the absolute level of the
and
measure the distance betrace, the delta markers
tween their position and the reference marker. All marker coordinates are shown in the two parameter lines above the
diagram.
e Resolution bandwidth
A spectrum analyzer can differentiate two spectral lines separated by a minimum distance corresponding to the bandwidth
of the resolution filter.
The smaller the bandwidth the better the resolution and the
larger the signal-to-noise ratio. If the resolution bandwidth is
too large only the envelope of the spectrum can be measured.
In the Power measurement, the signal-to-noise ratio improves
but the time resolution deteriorates when the resolution
bandwidth is reduced.
)
Chapter 4 of the operating
manual
The Frequency softkey defines
the frequency of the measured
signal and the resolution bandwidth. The Input Level softkey
configures the input level, the
power range and an attenuation
factor. The Time softkey configures the time axis.
)
Chapter 4 of the operating
manual
In addition to markers, a D-line
can be used to measure a particular level in the diagram.
)
Chapter 4 of the operating
manual
)
Chapter 4 of the operating
manual
... on Step 5
f Scaling of the spectral diagram
The tools provided in the Spectrum menu are particularly
suitable for scaling a spectral diagram with a sharp main lobe
and symmetric, lower side lobes:
• The R to Pk hotkey (Marker softkey) places the reference
marker to the maximum (i.e. the main lobe) of the diagram.
• The Cnt to R hotkey (Marker softkey) centers the diagram
to the frequency of the main marker.
• Equivalently, the Center hotkey (Frequency/RBW softkey)
can be used to center the diagram.
1100.4961.62
2.13
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
R&S CMU 200
Index
Index
List software ................................................................ 1.36
Log file
Remote Service Tool ................................................. 1.29
A
AC supply connection...................................................1.11
Activate other software.................................................1.30
M
Main power switch ................................................ 2.4, 2.12
Monitor ........................................................................ 1.19
B
Back to previous screen ...............................................1.31
N
C
Non volatile ram........................................................... 1.37
Notify message (VersionManager)............................... 1.38
Null-modem ................................................................. 1.17
Command Button (Remote Service Tool ......................1.29
Configuration
firmware .....................................................................1.30
Configure Command Buttons .......................................1.29
Connection
controller ..................................................1.16, 1.22, 1.27
external keyboard.......................................................1.19
IEC bus ......................................................................1.17
monitor .......................................................................1.19
RS-232 .......................................................................1.17
Controller connection ...................................................1.16
Copy non volatile ram to disk .......................................1.37
P
PC-card selection dialog .............................................. 1.32
Power fuses................................................................. 1.11
Power switch ............................................................... 1.11
Putting into Operation ........................................... 1.1, 1.10
AC supply connection ................................................ 1.11
EMC .......................................................................... 1.15
instrument setup ........................................................ 1.10
mounting in a rack ..................................................... 1.11
switching on............................................................... 1.11
unpacking .................................................................. 1.10
D
Defragment disk ...........................................................1.37
Delete non volatile ram.................................................1.37
Delete software ............................................................1.31
R
Rack mounting............................................................. 1.11
RAM ............................................................................ 1.37
Rear view ...................................................................... 1.7
Remote control
Remote Service Tool ........................................ 1.25, 1.28
Remote Service Tool ................................................... 1.21
E
Edit service tables ........................................................1.36
EMC.............................................................................1.15
Error messages
VersionManager .........................................................1.38
Exit...............................................................................1.37
External keyboard ........................................................1.19
S
Scan disk..................................................................... 1.37
Setting up (CMU)......................................................... 1.10
Software installation
Remote Service Tool ................................................. 1.22
Software update .......................................................... 1.21
Software version selection dialog ................................ 1.33
Standby mode ...................................................... 1.12, 2.5
Startup menu ........................................................ 1.13, 2.4
Switching on ................................................................ 1.11
F
File transfer
Remote Service Tool ..................................................1.24
Firmware configuration .................................................1.30
Firmware update ..........................................................1.21
Firmware update after board change............................1.36
Front view ..................................................................... 1.1
Fuses ...........................................................................1.11
U
G
Unpacking ................................................................... 1.10
Upgrade firmware ........................................................ 1.33
Getting Started .............................................................. 2.1
GPIB bus
interface .....................................................................1.16
V
I
Versions.new ............................................................... 1.29
VGA monitor ................................................................ 1.19
IEC/IEEE bus ................................................see GPIB bus
Info...............................................................................1.37
Input level.....................................................................1.15
Install software .............................................................1.32
W
Write log files to disk.................................................... 1.37
L
List all versions to disk .................................................1.37
1100.4961.62
I.1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
E-1
For your
User Documentation
CD-ROM
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Artisan Technology Group is your source for quality
new and certified-used/pre-owned equipment
• FAST SHIPPING AND
DELIVERY
• TENS OF THOUSANDS OF
IN-STOCK ITEMS
• EQUIPMENT DEMOS
• HUNDREDS OF
MANUFACTURERS
SUPPORTED
• LEASING/MONTHLY
RENTALS
• ITAR CERTIFIED
SECURE ASSET SOLUTIONS
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff
at our full-service, in-house repair center
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins
www.artisantg.com/WeBuyEquipment
InstraView REMOTE INSPECTION
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical
specifications, manuals, and documentation
SM
Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com
Contact us: (888) 88-SOURCE | [email protected] | www.artisantg.com