The Liberty Bed Service Manual 999-0822-190G

The Liberty Bed Service Manual 999-0822-190G
LIBERTY
SERIES
INSTRUCTIONS FOR USE
SERVICE MANUAL
To avoid personal injury or damage to bed,
read all sections pertaining to the bed model before use.
ETL/UL/CSA APPROVED
UL 60601-1
IEC 60601-2-38
CSA 22.2 601.1
GF Health Products, Inc. - www.grahamfield.com
Liberty Series Service Manual 999-0822-190G MAY 2015
This service manual covers the following Liberty Models:
76" and 80" Full Electric with Standard Caster System and Grid Decks: LBT7174;
76" and 80" Full Electric with Locking Caster System and Grid Decks: LBTL7174
Basic American Medical Products
336 Trowbridge Drive
Fond du Lac, WI 54937
For Liberty Bed service parts,
contact our Customer Service Department
at 770-368-4700
Manufactured by:
GF Health Products, Inc.
2935 Northeast Parkway
Atlanta, GA 30360
www.grahamfield.com
Made in the USA
To order a Liberty bed,
contact a GF Health Products, Inc. sales representative
at 770-368-4700
IMPORTANT NOTICE
GF Health Products, Inc. is not responsible for typographical errors.
All illustrations, specifications, packaging, and warranties contained in this Service Manual
are based on the latest product information available at the time of printing.
The most current product information can be found online at www.grahamfield.com.
Check all parts for shipping damage and test before using.
In case of damage, DO NOT USE.
LIBERTY SERIES
TABLE OF CONTENTS
IMPORTANT SAFETY AND WARNING INFORMATION.................................................. 4
IMPORTANT SAFETY AND WARNING INFORMATION.......................................... 5
ENTRAPMENT AND COMPLIANCE INFORMATION.............................................. 5
RECOMMENDED MAINTENANCE.......................................................................... 6
ENVIRONMENTAL SPECIFICATIONS AND RFI INFORMATION............................ 7
OPERATING CONDITIONS...................................................................................... 7
STORAGE AND TRANSPORT CONDITIONS.......................................................... 7
DISPOSAL OF EQUIPMENT AND ACCESSORIES................................................. 7
SECTION A: BED SETUP INSTRUCTIONS..................................................................... 8
UNPACKING THE BED............................................................................................. 8
HEADBOARD AND FOOTBOARD ASSEMBLY/INSTALLATION............................. 9
STANDARD MATTRESS RETAINER INSTALLATION........................................... 11
STANDARD WIREFORM WALLSAVER INSTALLATION....................................... 12
OPERATION— HAND CONTROL PENDANT........................................................ 13
OPERATION—HI/LO AND DECK POSITIONS...................................................... 14
OPERATION—OPTIONAL PEDAL LOCK.............................................................. 15
SECTION B: ASSIST DEVICES...................................................................................... 16
OPTIONAL ASSIST BAR INSTALLATION—HEAD END ONLY.............................. 16
OPTIONAL PIVOT ASSIST BAR INSTALLATION—HEAD END ONLY.................. 17
OPTIONAL HALF RAIL INSTALLATION—HEAD END ONLY................................ 18
FOOT-END MOUNTING BRACKET AND CROSSTUBE INSTALLATION FOR
OPTIONAL FOOT-END ASSIST DEVICES......................................................... 19
OPTIONAL HALF RAIL INSTALLATION—FOOT END........................................... 20
OPTIONAL TRAPEZE SUPPORT INSTALLATION................................................ 21
OPTIONAL 4" EXTENSION PAN INSTALLATION.................................................. 22
ONE-STEP LOCKING MECHANISM INSTALLATION—MODEL LBTL7174.......... 23
SECTION C: MECHANICAL AND ELECTRICAL INFORMATION................................. 24
SECTION D: SERVICE/REPLACEMENT PARTS.......................................................... 26
SECTION E: DECK/MECHANICAL SERVICE PARTS................................................... 29
SECTION F: TROUBLESHOOTING............................................................................... 32
LIMITED WARRANTY..................................................................................................... 34
LABEL SYMBOL DEFINITIONS
!
!
Consult
Accompanying
Documents
Safe
Working
Load
GF Health Products, Inc. - www.grahamfield.com
Double
Insulated
Protected
Grounded
Device
Type B
Equipment and
Applied Parts
3
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
IMPORTANT SAFETY AND WARNING INFORMATION
!
This product is a variable height, adjustable
mattress platform, which will provide comfort and
convenience for residents/patients and caregivers in
long term care settings.
!
The MAXIMUM SAFE WORKING LOAD for the
Liberty Bed with weight evenly distributed, including
bedding, resident/patient, support surface, and all
accessories, is 450 lb.
!
!
!
!
!
!
!
!
!
!
!
NEVER operate the bed if a Power Cord or Plug is
damaged or not working properly. Contact qualified
Service Personnel for examination and repair.
ALWAYS unplug the Power Cord before performing
maintenance on the bed.
DO NOT open assemblies such as the Actuators,
Hand Control Pendant, or Control Box. If
unauthorized personnel perform work on these
components, the manufacturer’s warranty becomes
void.
DO NOT use unauthorized parts, accessories, or
adapters other than those specified/authorized by GF
Health Products, Inc.
When operating the bed’s HI/LO, Knee, or Back
Functions, ALWAYS ensure the confined individual
is positioned properly within the confines of the
bed. DO NOT let any extremities protrude over the
side or between the bed rails when performing these
functions.
DO NOT lower the bed when objects are beneath it.
Failure to inspect under the bed can result in personal
injury or property damage.
The bed’s Hand Control Pendant Cable MUST BE
ROUTED AND SECURED PROPERLY to ensure
it does not become entangled and eventually severed
during use. Also ensure electrical cords DO NOT
get tangled around the bed, side rails, or legs during
transport or normal operation of the bed.
When using nasal-type or masked-type administering
equipment, all oxygen or air tubing MUST BE
ROUTED AND SECURED PROPERLY to ensure
the tubing does not become entangled and eventually
severed during the normal operation of the bed.
Keep all moving parts free of obstructions (i.e.
blankets/sheets, heating blankets/pads, wiring, etc.).
!
!
!
!
Beds manufactured by Basic American Medical
Products are designed for use within an institutional
healthcare environment (i.e. assisted living, skilled
nursing, transitional care, rehabilitation care, etc.).
DO NOT use the assist devices as push handles for
moving the bed. Assist devices can be deformed or
broken if excessive side pressure is exerted. Assist
devices are not meant for patients considered high
risks for entrapment (i.e. patients with pre-existing
conditions such as confusion, restlessness, lack of
muscle control, altered mental status, either organic
or medicinal, or a combination thereof). Additional
safety measures should be considered for such highrisk patients.
NEVER permit more than one person on/in the bed at
any time.
Body weight should be evenly distributed over the
sleeping surface of the bed. DO NOT allow the
patient to lie, sit, or lean in such a way that their
entire body weight is placed only on the raised head
or foot section of the bed. This especially applies
when repositioning or transferring a patient in or
out of the bed. Increased risk may occur when the
patient’s size and/or weight are inappropriate for the
bed’s dimensions or weight capacity.
Risk of entanglement or injury may occur if the
mattress used with mattress retainers does not fill the
entire width between stops or which compresses to
less than 1.50 inches under user’s weight.
Mattress must be properly sized to fit the mattress
support platform and must remain centered on
the support platform relative to State and Federal
guidelines. Recommended minimum dimensions
of mattress are 35 inches wide and 6 inches deep.
Length should match the mattress support platform.
Use of an improperly fitted mattress could result in
injury or death.
!
IMPORTANT: Powered air mattress surfaces may
pose a risk of entrapment. Prior to use, ensure the
therapeutic benefits outweigh the risk of entrapment.
!
The bed is intended for use within a temperature
range of 10˚C to 40˚C. It has a water resistance
rating of IPX4 and IS NOT to be power washed or
submerged.
The bed should ALWAYS be left in the lowest
position when unattended to reduce the risk of injury
during patient entry and exit.
GF Health Products, Inc. - www.grahamfield.com
4
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
IMPORTANT SAFETY AND WARNING INFORMATION
!
!
The head/back and knee/foot decks can be lifted
freely by hand for easy cleaning access when patients
are not in the bed. If you lift the head/back or knee/
foot deck for any reason, take great care when
lowering back down to the prone position - ensure
all body parts are clear of the space between the
deck and the bed prior to slowly lowering any deck
manually. To avoid injury, DO NOT LET DECKS
FALL FREELY FROM ANY ANGLE.
Notice for California Customers - California
Proposition 65 WARNING: This product contains a
chemical known to the State of California to cause
cancer and reproductive or developmental harm.
!
Proper routing and tie-off of electrical cabling,
especially the power cord, is essential for proper
operation and to ensure safety from electrical shock.
In the event you are replacing any electrical cabling
on your bed, you must ensure the cables are free
from pinch points, obstructions, or stretched so tight
that they may come loose or become damaged. In
addition, cables should be tied off in such a way to
secure them and keep them free from tangling on any
part of the bed during normal operation. Refer to your
service manual’s electrical section for proper cable
routing.
ENTRAPMENT AND COMPLIANCE INFORMATION
On April 10, 2006, the FDA (U.S. Food and Drug
Administration) released long-awaited guidelines for reducing
the risk of bed entrapment: “Hospital Bed System Dimensional
and Assessment Guidance to Reduce Entrapment”. The new
Guidance identifies potential entrapment areas and those
body parts most at risk for entrapment; provides design
criteria for manufacturers of new hospital/convalescent beds;
recommends particular test methods to assess the conformance
of existing hospital/convalescent bed systems; and answers
frequently-asked questions about entrapment issues.
The new Guidance was a result of a long-standing
collaboration between the FDA and the Hospital Bed Safety
Workgroup (HBSW), formed in 1999. GF Health Products,
Inc.’s Long Term Care Bed division: Basic American Medical
Products, is an HBSW charter member. As a result of our
commitment to product safety, all our current long-term
care beds have been strictly tested and conform to the new
FDA Guidance.
It is also essential to have the correct bed components/
accessories that correspond with the needs of the patient/
resident and the particular bed you have purchased. Matching
the correct bed component that correlates with the regulatory
guidelines can be a daunting task. Our sales team at GF
Health Products, Inc. and our friendly Customer Service
Representatives at Basic American Medical Products can help
you sift through the wide array of compliance and bed options.
We will help you determine which bed/bed part is best for the
patient’s/resident’s particular needs and help you with any
compliance issues.
The Liberty Bed and accessories listed in this manual are
in full compliance with FDA guidelines for reducing the
risk of bed entrapment: “Hospital Bed System Dimensional
and Assessment Guidance to Reduce Entrapment”.
Details can be found at www.fda.gov.
The guidelines set forth by the FDA Guidance layout specific
dimensional limitations on potentially injury-threatening gaps
and spaces that can occur between bed system components,
such as rails, when not properly installed. GF Health Products,
Inc. and Basic American Medical Products have conformed
to these guidelines from a manufacturing aspect. However,
entrapment issues can often arise when a healthcare provider/
facility has not correctly assembled the components on a bed.
It is essential that the provider/facility fully understand their
responsibility in complying to the guidelines set forth by the
FDA in order to avoid injury. To that end, we have provided
the FDA’s web address at right as a resource for understanding
and following these guidelines for the safety of patients/
residents.
GF Health Products, Inc. - www.grahamfield.com
5
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
RECOMMENDED MAINTENANCE
Regular maintenance of the Long Term Bed is necessary to ensure continuing proper and safe operation.
Read and observe the following recommended maintenance schedule.
RECOMMENDED
INSPECTION PERIODS
ITEM
Inspect
on Receipt
Every
3 Months
Every
6 Months
Maintenance Inspection of All Components at Receipt of Shipment
Ensure all parts/components are included (see “Unpacking The Bed”).
X
Check all bed components for obvious damage.
X
Inspect the power cord for any cuts and/or damage.
X
Check to see all actuator/motor cables are routed and connected properly to the control
box.
X
Mechanical Inspection of Assemblies
Inspect all welds on the sleeping surface, frame, and base assemblies for stress
fractures.
X
Inspect all fasteners for wear and looseness.
X
Mechanical Inspection of Casters and Pedal Locking Mechanism
Check the pedal locking mechanism to ensure it engages and disengages properly.
X
Check the casters and stationary foot pads on both the head end and foot end for any
damage, wear, or debris. Replace if needed.
X
Check all rolling casters to ensure that they roll properly and are unobstructed.
X
Electrical Inspection of Control Box, Hand Control Pendant, and Staff Control
Check the external power cord that plugs into the control box for any chafing, cuts, or
wear. Replace if damaged.
X
Ensure all attaching hardware is securely tightened.
X
Check all electrical connections for wear or fractures.
X
Check the external backup battery (if you have one). Replace if needed.
X
Check the hand control pendant cable for chafing, cuts, or wear.
X
Check all hand control pendant functions - check to ensure each button and associated
function work properly (i.e. head section rises when the HEAD UP button is activated).
X
Electrical Inspection of Actuators/Motors
Check the actuator/motor cables for any chafing, cuts, or wear.
X
Check the range of movement on all motors to ensure they do not bind in the Full Up or
Full Down positions.
X
GF Health Products, Inc. - www.grahamfield.com
6
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
The following warning labels have been placed on the bed to help protect you and the bed from
damage. Do not remove any labels from the bed.
WARNING!
DO NOT LOWER BED WHEN OBJECTS ARE
BENEATH BED. FAILURE TO INSPECT UNDER
BED CAN RESULT IN DAMAGE TO PROPERTY
OR PERSONAL INJURY.
ATTENTION:
S’assurer de ne pas faire descendre le lit
lorsque des objets se trouvent sous le lit. Ne
pas inspecter le dessous du lit pourrait entrainer
des dommages materiels et des risques de
blessures.
CAUTION
THIS BED IS SUITABLE FOR USE ONLY WITH
OXYGEN ADMINISTERING EQUIPMENT OF
THE NASAL OR MASK TYPE OR A TENT
COVERING ONLY THE UPPER HALF (HEAD
END) OF THE BED. OXYGEN TENT CANOPIES
SHOULD NOT EXTEND BELOW BED SPRING
LEVEL. LOCK HAND CONTROL AT FOOT OF
BED WHEN USING OXYGEN ADMINISTERING
EQUIPMENT.
ATTENTION:
WARNING!
DO NOT LOWER BED WHEN
OBJECTS ARE BENEATH BED.
FAILURE TO INSPECT UNDER
BED CAN RESULT IN DAMAGE
TO PROPERTY OR PERSONAL
INJURY.
CE LIT PEUT ETRE UTILISE UNIQUEMENT
AVEC UN EQUIPMENT DESTINE A
L’ADMINISTRATION D’OXYGENE DE TYPE
NASAL OU MASQUE OU AVEC UNE TENTE
RECOUVRANT SEULEMENT LA MOTTIE
AVENT (TETE) DU LIT. LES COTES DE LAS
TENTE OXYGENE NE DOIVENT PAS SE
PROLONGER PLUS DAS QUE LA SOMMIER
DU LIT.
ENVIRONMENTAL SPECIFICATIONS AND RFI INFORMATION
OPERATING CONDITIONS
STORAGE AND TRANSPORT CONDITIONS
Ambient Temperature
10°C to 40°C
Temperature
-40°C to 70°C
Relative Humidity
30% to 75% Non-Condensing
Relative Humidity
10% to 100%
Atmospheric Pressure 700 to 1060 hPa
Protected Against
Splashing Water
Atmospheric Pressure 500 to 1060 hPa
IPX4
RFI (RADIO FREQUENCY INTERFERENCE)
RFI influences most electronic equipment. Caution should be exercised with regard to the use
of portable communications equipment in the area around such equipment. If RFI causes erratic
behavior, shut the bed off immediately. Leave it off while the transmission is in progress.
DISPOSAL OF EQUIPMENT AND ACCESSORIES
Follow local governing ordinances and recycling plans regarding disposal of the device or
components normally used in operation. The device does not generate waste or residue in
operation. Any accessories not part of the device MUST be handled in accordance with the
individual product marking for disposal.
GF Health Products, Inc. - www.grahamfield.com
7
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
SECTION A: BED SETUP INSTRUCTIONS
UNPACKING THE BED
• Ensure all parts/components are included.
• Check all bed components for obvious
damage.
• Inspect the Power Cord for cuts or damage.
• Ensure all actuator/motor cables are routed
and connected properly to the control box.
DISCARD
1.
2.
3.
4.
Cardboard Block
Notched Leg Foam
Large Blocks
Large Cable Tie - CUT
KEEP
5. Hand Control Pendant, Pendant
Holster, and Coiled Power Cord *
6. One Mattress Retainer
7. One Wireform Wallsaver
8. Panel Mounting Brackets and
Hardware to attach Headboard and
Footboard
* NOTE: HAND CONTROL PENDANT,
PENDANT HOLSTER, AND COILED
POWER CORD ARE CABLE-TIED TO
HEAD DECK GRID WIRE — CUT AND
DISCARD THIS CABLE TIE WHEN
YOU UNPACK THE BED.
ALSO DISCARD TOP
AND BOTTOM
CARTONS
GF Health Products, Inc. - www.grahamfield.com
8
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
HEADBOARD AND FOOTBOARD ASSEMBLY/INSTALLATION
HEADBOARD INSTALLATION
1. The headboard may come with four
pre-installed inserts - if not already installed,
assemble the four inserts (#4) into the
outside of the headboard as shown at right.
2. Position a right (#2) and left (#3) mounting
bracket on the inside of the headboard with
tubes facing inward as shown below.
3. Align the bracket top holes with the
headboard top holes.
4. Insert a socket head cap screw (#5) through
each of the top holes and bottom holes and
screw into each insert. Tighten with the hex
key included in the kit.
5. At the head deck end, slide the bracket
tubes into the main frame rail hollow ends.
6. FOR 80" BEDS: Slide the mounting tubes
in until the bracket tube hole aligns with the
first rail hole as shown at right.
7. FOR 76" BEDS: Slide the mounting tubes
in until the bracket tube hole aligns with the
second rail hole as shown at right.
NOTE: To order a new Headboard Panel
Mounting Kit, use Part # 999-0822-000. Kit
includes right and left Mounting Brackets,
8 Socket Head Cap Screws, 4 Clevis Pins,
4 Hair Pin Clips, and 1 Hex Key. Headboard
and Footboard kits are sold separately.
GF Health Products, Inc. - www.grahamfield.com
HEADBOARD
MOUNTING
FOR 80" BED
Inserts may be
pre-installed
DETAIL A
MOUNTING POSITIONS
DETAIL B
MOUNTING
FOR 76" BED
9
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
FOOTBOARD INSTALLATION
1. The footboard may come with four
pre-installed inserts - if not already installed,
assemble the four inserts (#4) into the
outside of the footboard as shown at right.
2. Position a right (#2) and left (#3) mounting
bracket on the inside of the footboard with
tubes facing inward as shown below.
3. Align the bracket top holes with the
footboard top holes.
4. Insert a socket head cap screw (#5) through
each of the top holes and bottom holes and
screw into each insert. Tighten with the hex
key included in the kit.
5. At the foot deck end, slide the bracket tubes
into the main frame rail hollow ends.
6. FOR 80” BEDS: Slide the mounting tubes
in until the bracket tube hole aligns with the
first rail hole as shown at right.
7. FOR 76” BEDS: Slide the mounting tubes
in until the bracket tube hole aligns with the
second rail hole as shown at right.
NOTE: To order a new Footboard Panel
Mounting Kit, use part # 999-0822-000. Kit
includes right and left Mounting Brackets,
8 Socket Head Cap Screws, 4 Clevis Pins,
4 Hair Pin Clips, and 1 Hex Key. Headboard
and Footboard kits are sold separately.
GF Health Products, Inc. - www.grahamfield.com
Inserts may be
pre-installed
FOOTBOARD
MOUNTING
FOR 80" BED
DETAIL A
MOUNTING POSITIONS
DETAIL B
MOUNTING
FOR 76" BED
10
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
STANDARD MATTRESS RETAINER INSTALLATION
(USING 2 RETAINERS 999-0844-124)
The Liberty Bed mattress retainer was designed to span the
width of the sleeping surface. One retainer is shipped with your
bed and is typically placed at the foot end, although it will fit on
either end.
1. Determine if you need to position your bed in an 80" or 76"
configuration (80" length bed = outside holes; 76" length
bed = inside holes - see insert below).
2. If installing mattress retainer on the foot end, carefully
squeeze the Mattress Retainer ends inward, toward the
center of the retainer, and insert the ends into the proper
holes (see Details A and B). Lay the Mattress Retainer
down so that the elbows rest on the decks and the long
cross rod is on the foot end side as shown.
!
Be sure to use a mattress that is properly sized to fit
the sleep deck, which will remain centered on the
deck relative to State and Federal Guidelines. Use of
an improperly fitted mattress could result in injury or
death.
GF Health Products, Inc. - www.grahamfield.com
3. If installing mattress retainer on the head end, carefully
squeeze the Mattress Retainer ends inward, toward the
center of the retainer, and insert the ends into the proper
holes (see Details A and B). Lay the Mattress Retainer
down so that the elbows rest on the decks and the long
cross rod is on the foot end side as shown.
!
Use a properly sized mattress in order to minimize
the gap between the side of the mattress and assist
devices. This gap must be small enough to prevent
resident/patient from getting their head or neck
caught in this location.
11
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
STANDARD WIREFORM WALLSAVER INSTALLATION
WALLSAVER ASSEMBLY
WALLSAVER REMOVAL
The Liberty Bed is shipped with a wireform wallsaver for the
head end of the bed. No hardware is necessary to attach this
multi-positional accessory.
1. To remove or move the wallsaver to a new position, raise
the wallsaver off the floor until the end tabs are horizontal.
To attach: bend in the tabbed ends into the slots in the carriage
rails and lock down into place. There is even a position if you
choose to install an optional trapeze support at the head end
of the bed. (See page 21 for Trapeze Support installation in the
Assist Devices section of this manual.)
2. Squeeze the ends toward the center of the wallsaver until
the end tabs slide out of the caster base holes.
FINAL WALLSAVER
RESTING POSITION
WALLSAVER
ATTACHING POSITION
TO LOCK FLAT TAB INTO
CARRIAGE RAIL, TURN
TAB IN SIDE HOLE UNTIL
WALLSAVER RESTS ON
CROSSBRACE
INSERT FLAT TAB SO
THAT IT IS PARALLEL
WITH CASTER
CARRIAGE RAIL SLOT
Wallsaver hole for 80" Bed with Trapeze
Wallsaver hole for 76" Bed with Trapeze
Wallsaver hole for 80" Bed without Trapeze
Wallsaver hole for 76" Bed without Trapeze
GF Health Products, Inc. - www.grahamfield.com
12
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
OPERATION— HAND CONTROL PENDANT
The Liberty Bed is equipped with a Hand Control Pendant. Every control function (head/back, knee,
and foot) has two easily recognizable switches for up and down movement. The pendant can be
easily disconnected to deactivate the patient control functions. To operate the Hand Control Pendant,
press the appropriate button to activate the desired function as shown in chart below.
HAND CONTROL PENDANT OPERATION
2
1
4
3
5
6
1
HEAD DECK ANGLE UP BUTTON
2
HEAD DECK ANGLE DOWN BUTTON
3
HI/LO UP BUTTON (RAISE ENTIRE BED)
4
HI/LO DOWN BUTTON (LOWER ENTIRE BED)
5
KNEE AND FOOT DECK ANGLE UP BUTTON
6
KNEE AND FOOT DECK ANGLE DOWN BUTTON
The Hand Control Pendant Holster
999-0791-000SP comes standard
with the Liberty Bed.
HAND CONTROL PENDANT
The Liberty Bed comes with a Hand
Control Pendant. To order a replacement
Hand Control Pendant, see page 26.
The Hand Control
Pendant Cable has
a phone jack connector.
NOTE: The easiest way deactivate the Hand Control Pendant function for patient use is to unplug the
power cord from the wall socket or other power supply when the patient is left alone in the bed. When
you need to use the Hand Control Pendant function to raise or lower the bed or decks, replug the
power cord into the power outlet.
GF Health Products, Inc. - www.grahamfield.com
13
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
OPERATION—HI/LO AND DECK POSITIONS
The Liberty Bed has a variety of positions to increase patient comfort and practitioner/caregiver
access during procedures and transfers. The correct placement of the bed is essential for the
patient’s safety. The bed should always be set to its lowest position when the resident/patient is left
unattended. The head/back and foot/knee functions allow the resident/patient to comfortably raise
their head or legs. In the event of a power outage, it is preferred that the knee and head/back sections
be lowered using an emergency battery pack.
FOOT
END
HEAD
END
QUICK REFERENCE
Bed Height - floor to sleep deck top
MAXIMUM (High Position) = 24.50"
MINIMUM (Low Position) = 9.95"
Head Deck to Sleep Surface
MAXIMUM (Head Angle) = 70°
Knee Deck to Sleep Surface
MAXIMUM (Knee Angle) = 30°
Knee Deck to Foot Deck
MAXIMUM (Knee/Foot Angle) = 45°
GF Health Products, Inc. - www.grahamfield.com
14
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
OPERATION—OPTIONAL PEDAL LOCK
ONE-STEP LOCKING MECHANISM
Liberty Bed Locked Position
To lock the foot end of the Liberty bed,
step on the red pedal until the lock engages.
The green release lever will show through
the slot in the top of the locking mechanism.
To fully lock the bed,
ensure the caster keepers at the head of
the bed are both in their down positions.
Liberty Bed Unlocked Position
To unlock the foot end of the Liberty bed,
step on the green release pedal until the
lock disengages. The green release lever
will disappear through the slot in the top of
the pedal locking mechanism and the red
pedal will raise.
To fully unlock the bed,
ensure the caster keepers at the head of
the bed are both in their up positions.
GF Health Products, Inc. - www.grahamfield.com
15
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
SECTION B: ASSIST DEVICES
OPTIONAL ASSIST BAR INSTALLATION—HEAD END ONLY
(KIT ZA80300: INCLUDES ONE ASSIST BAR AND HARDWARE)
Installation—Bracket
2. Insert the Hair Pins on the opposite end of
the Lanyard Assemblies (#2b) into the small
holes at the ends of the clevis pins.
With the Assist Bar (#1) bracket facing inward
toward the bed as shown below, align the two
large bracket holes with the two head deck
mounting bracket holes.
Installation—Fixed Attachment Head End
Assist Bar (Option 2)
1. Insert the two cap screws (#3) from the
outside through the Assist Bar bracket and
mounting bracket holes.
2. Secure screws by attaching two Thin Nylon
Lock Nuts (#4) and tighten using two 13/16
wrenches.
Installation—Quick-Release Head End Assist
Bar (Option 1)
1. Insert the two Lanyard Assembly Clevis Pins
(#2a) from the outside through the Assist
Bar bracket and mounting bracket holes.
2a
ASSIST BAR
999-0803-902G
SHOWN AT RIGHT HEAD END
2a
(Hardware Bag 999-0803-905
includes mounting hardware for both
quick-release and fixed options)
2b
QUICK-RELEASE
HEAD END
(OPTION 1)
2b
!
WARNING: When assessing the Risk of Entrapment, consider
the bed, mattress, headboard, footboard, assist devices (i.e.
rails and assist bars) and other accessories as an entire system.
All bed systems are evaluated for full compliance to the FDA/
CDRH “Hospital Bed System Dimensional and Assessment
Guidance to Reduce Entrapment” guidelines.
GF Health Products, Inc. - www.grahamfield.com
FIXED ATTACHMENT
HEAD END
(OPTION 2)
16
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
OPTIONAL PIVOT ASSIST BAR INSTALLATION—HEAD END ONLY
(KIT ZA85500: INCLUDES ONE ASSIST BAR AND HARDWARE)
Installation
1 On the head end, align the two holes in the
Pivoting Assist Bar (#2) bracket with the two holes
in the mounting bracket on the underside of the
Head Deck (#1).
HEAD
2. From the outside, insert the
END
two 4.00” Clevis Pins (#3)
through the holes in the
Pivoting Assist Bar bracket
and Head Deck
mounting bracket.
3. From the inside, insert a
2.375” Hair Pin Clip through
the small holes at the ends
of each of the Clevis Pins
to secure.
Operation
1. To release the Pivoting Assist Bar from
its vertical lock position, hold onto the top
of the bar with one hand and slightly pull
out the black knob on the outside of the
assembly with the other hand to release the
locking mechanism. For your safety, make
sure your fingers are not near the pivot
assembly when pivoting the rail. For ease of
patient access, it is recommended that you
pivot the rail toward the headboard until it
stops and rests in place.
2. To set the assist bar back to its upright
locked position, grab the top of the assist
bar with one hand and pivot the assembly
upward until the black knob mechanism
snaps into place, locking the assist bar
vertically.
TO AVOID PINCHING FINGERS,
TO AVOID PERSONAL INJURY,
ENSURE THE PIVOTING ASSIST BAR
ENSURE FINGERS ARE CLEAR OF
IS ALWAYS
IN THE FULL,
VERTICAL,
OR UNDERSIDES
AIR MATTRESS
SURFACES
TO AVOIDSIDES
PERSONAL
INJURY, OF THE POWERED
LOCKED
POSITION
WHENEVER
PIVOTING
ASSEMBLY
WHEN
MAY POSE A RISK OF ENTRAPMENT.
ENSURE THE PIVOTING ASSIST BAR
IS LEFT
POSITIONING THE ASSIST BAR
PRIOR RESIDENT/PATIENT
TO USE, ENSURE THE
IS ALWAYS
IN THE FULL, VERTICAL,
UNATTENDED.
UP OR DOWN.
!
!
TO AVOID PINCHING FINGERS,
ENSURE FINGERS ARE CLEAR OF
SIDES OR UNDERSIDES OF THE
PIVOTING ASSEMBLY WHEN
POSITIONING THE ASSIST BAR
UP OR DOWN.
GF Health Products, Inc. - www.grahamfield.com
!
!
!
LOCKED POSITION WHENEVER
RESIDENT/PATIENT IS LEFT
UNATTENDED.
THERAPEUTIC BENEFITS
OUTWEIGH THE RISK OF
ENTRAPMENT.
17
Liberty Series Service Manual 999-0822-190G
!
P
M
P
T
O
E
LIBERTY SERIES
OPTIONAL HALF RAIL INSTALLATION—HEAD END ONLY
(KIT ZA82800; INCLUDES HALF RAIL AND HARDWARE)
NOTE: Kit ZA82800, for both 80" and 76" length beds, includes attachment hardware for both
Option 1 and Option 2 below.
IMPORTANT: Lubricate all pivot joints as needed with Aerosol White Lithium Grease.
Installation
1. Left and right Half Rails mount to the Head Half Rail
with
bed in a similar fashion; left or right
Quick-Release
designation is based on the
Hardware
patient’s orientation while
(Option 1)
occupying the bed.
2. Insert the two Clevis Pins (#3a),
with Circle Cotter and Lanyard
Cable, into the two Half
Rail arms.
3. Attach the Half Rail
to the Head Deck’s
welded mounting
bracket by aligning
the arms (with Clevis
Pins) to the bracket holes.
4. a. For Quick Release
(Option 1), insert the
Clevis Pin ends of the Lanyard assembly (#3a)
from the outside through the pivot arm and
mounting bracket holes. From the inside,
secure with Hair Pin Clips on the other side
Head Half Rail
of the Lanyard Assembly (#3b).
with Fixed
b. For Fixed Position (Option 2), insert the
Attachment
5/8-11 x 4.50" Cap Screws (#4) from the
Hardware
outside through the rail and bracket holes.
(Option 2)
From the inside, secure the screws with
5/8-11 Nylock Nuts (#5).
!
!
WARNING: When assessing the Risk of Entrapment,
consider the bed, mattress, headboard, footboard, assist
devices (i.e. rails and assist bars) and other accessories
as an entire system. All bed systems are evaluated for
full compliance to the FDA/CDRH “Hospital Bed
System Dimensional and Assessment Guidance to
Reduce Entrapment” guidelines.
WARNING: It is extremely important to review the resident/patient’s physical and mental condition and initiate an
appropriate individual care plan to address any entrapment risks. See page 5 for further information.
GF Health Products, Inc. - www.grahamfield.com
18
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
FOOT-END MOUNTING BRACKET AND CROSSTUBE INSTALLATION
FOR OPTIONAL FOOT-END ASSIST DEVICES
(KIT ZA82900; INCLUDES TWO CROSSTUBES, TWO MOUNTING
BRACKETS, AND HARDWARE)
1. Locate the two Crosstubes (#3) in your kit. Align the
outside oblong holes with the appropriate foot deck
holes—fourth and seventh holes from the foot deck
foot end.
2. From the top, insert a 5/16-18 x 1.75" Button Head
Machine Screw (#5) from your kit through each of the
holes in both the deck and the deck tubes.
3. From the bottom, secure the screws to the tubes
using four 5/16-18 Thin Nylock Nuts (#6). Hand
tighten.
4. Locate the two long U-shaped Rail Mounting
Brackets (#4) in your kit. The brackets should be
oriented so that the top hole closest to the edge of
the bracket is furthest away from the foot end of the
bed. With the open end facing downward as shown,
align the top holes with the inside oblong holes on the
underside of the crosstubes.
5. From the top, insert a 5/16-18 x 1.75" Button Head
Machine Screw (#5) from your kit through each of the
holes in both the deck and the deck tubes.
6. From the bottom, secure the screws to the tubes
using four 5/16-18 Thin Nylock Nuts (#6).
7. Tighten all hardware using a 1/2" wrench and 3/16"
hex key.
GF Health Products, Inc. - www.grahamfield.com
19
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
OPTIONAL HALF RAIL INSTALLATION—FOOT END
(KIT ZA82900; INCLUDES TWO HALF RAILS, TWO CROSSTUBES,
TWO MOUNTING BRACKETS, AND HARDWARE)
NOTE: Kit ZA82900, for both 80" and 76" length beds, includes attachment hardware for both
Option 1 and Option 2 below.
IMPORTANT: Lubricate all pivot joints as needed with Aerosol White Lithium Grease.
Installation
1. Left and right Half Rails mount to the
bed in a similar fashion; left or right
designation is based on the
patient’s orientation while
occupying the bed.
2. To mount the half rails
to the bed foot end,
you must first attach
two rail brackets (#4)
and crosstubes (#5)
to the foot deck; see
installation instructions on
page 19.
3. Align the rail pivot arm holes
with the mounting bracket
holes as shown.
4. a. For Quick Release (Option 1),
insert the Clevis Pin ends of the
Lanyard assembly (#3a) from the
outside through the pivot arm and mounting
bracket holes. From the inside, secure with the
Hair Pin Clips on the other side of the Lanyard
Assembly (#3b).
b. For Fixed Position (Option 2), insert the 5/8-11 x
4.50" Cap Screws (#6) from the outside through
the rail and bracket holes. From the inside,
secure the screws with 5/8-11 Nylock Nuts (#7).
!
!
WARNING: When assessing the Risk of Entrapment, consider
the bed, mattress, headboard, footboard, assist devices (i.e. rails
and assist bars) and other accessories as an entire system. All
bed systems are evaluated for full compliance to the FDA/CDRH
“Hospital Bed System Dimensional and Assessment Guidance to
Reduce Entrapment” guidelines.
Foot Half Rail
with Quick-Release
Hardware (Option 1)
Foot Half Rail
with Fixed Attachment
Hardware (Option 2)
WARNING: It is extremely important to review the resident/patient’s physical and mental condition and initiate an
appropriate individual care plan to address any entrapment risks. See page 5 for further information.
GF Health Products, Inc. - www.grahamfield.com
20
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
OPTIONAL TRAPEZE SUPPORT INSTALLATION
(KIT ZA83000; ATTACHES TO THE HEAD SECTION OF THE BED)
1. Remove the headboard panel assembly (#3), if
previously assembled to the bed, by pulling out the
two Clevis Pins and Hair Pin Clips that attach the main
frame tubes to the headboard mounting brackets. Set
hardware aside for later use.
4. From the back, insert the four JCB Bolts (#5) you
removed in step 2 through the Trapeze Support
brackets into the headboard—they will thread into
the 1/4-20 inserts. Tighten all JCB bolts with the hex
key. DO NOT OVERTIGHTEN.
2. Detach the headboard panel from the mounting tubes
by removing the four 1/4-20 JCB Bolts (#5) from the
brackets using the M4 hex key included in your kit.
Remove the four 1/4-20 Inserts (#4) from the board by
inserting the opposite end of the hex key into the hole
and lightly tap with a hammer. Reinstall the inserts into
the four holes on the wood grain side of the board.
5. Assemble the Trapeze Support with headboard
attached to the main frame rails by inserting the
support’s tubes into the rails. The support tube end
vertical stops will help keep the trapeze support
level.
3. Position the headboard so that the wood grain finish
is facing inward toward the head deck. Align the
headboard holes with the Trapeze Support (#2) bracket
holes.
GF Health Products, Inc. - www.grahamfield.com
6. The Liberty Bed features two positions for the
Trapeze Support depending on the length of bed you
have (see Detail A below).
7. Secure the Trapeze Support to the rails using the
Clevis Pins (#6) and Hair Pin Clips (#7) you removed
in step 1.
21
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
OPTIONAL 4" EXTENSION PAN INSTALLATION
(KIT LBT83300)
1. The Extension Pan kit includes two footboard
mounting brackets that are used to extend the
footboard to accommodate the pan. If you already
have a Liberty bed and have purchased the 4.00"
Extension Kit, first remove your existing footboard
assembly from the bed.
2. Remove the two hair pin clips (one on each side)
from the clevis pins that attach the brackets to the
main frame tubes—detach the brackets from the
footboard by removing the four 1/4-20 x 20mm bolts
from the bracket insides. Retain the bolts for the next
step. Discard the old brackets if you do not need
them for future use.
3. Attach both the left bracket (#3) and right bracket (#4)
to the inside of the footboard, reusing the four bolts
(#5) you removed in step 2.
4. Slide the new footboard assembly into the main
frame tubes so that the bracket second holes align
with the tube first holes. Use four clevis pins (#6) and
Second hole
used for mounting
four hair pin clips (#7) to secure the brackets to the
tubes (either reuse the two sets you removed in step
1 and
two more from your kit, or all four from your kit).
5. Attach the extension pan to the foot deck—lay the
pan
on top of the foot deck so that the three bent sides
face upward and the side without any bends is
oriented toward the head end as shown.
6. Position the two oval holes at the end of the pan so
that they align with the last holes in the foot deck
(nearest the curved ends).
7. Insert a Washer (#9) onto each of the two Phillips
Pan Head Machine Screws (#10). From the top,
insert the screws and washers through the holes.
From the bottom, screw on two Flange Lock Nuts
(#11) to secure. Tighten the nuts with a 7/8" wrench.
First hole used
for mounting
GF Health Products, Inc. - www.grahamfield.com
22
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
ONE-STEP LOCKING MECHANISM INSTALLATION—MODEL LBTL7174
(KIT LBTL83200; INCLUDES PEDAL LOCK, CASTER KEEPERS,
FOUR NON-LOCKING CASTERS, AND HARDWARE)
View of Pedal Lock Attached
to the Foot End of Liberty Bed.
View of Caster Keeper
Assembly attached to
the Head End of Liberty
Bed. Caster Keepers
come pre-assembled
in kit.
1. Position the Locking Pedal Assembly (#2) so that the
mounting bracket is on top and the red pedal is facing
outward, away from the carriage.
2. Align the bracket holes with the pre-drilled crossbrace
holes.
3. From the outside, insert a 5/16-18 x 2.50" Hex Head
Bolt (#3) through both bracket and crossbrace holes.
4. From the inside, secure the bolt to the assembly
using a 5/16-18 Thin Nylock Nut (#4). Tighten with two
1/2" wrenches. (If you already have a lock mechanism
system on your Liberty bed and are attaching a
second Pedal Lock you are done and can skip steps
5 - 8.)
5. Remove the two locking casters at the foot end of
the carriage and replace them with two non-locking
casters (#9) from your kit. Use the same Locking
Nuts to secure.
6. Remove the two locking casters at the head end of
the carriage. Discard the nuts and locking casters.
From the bottom, insert the stems from the last two
non-locking casters from your kit into the carriage
holes.
GF Health Products, Inc. - www.grahamfield.com
7. Position the pre-assembled Caster Keepers (bent
arm outward and toward the foot end) onto the
exposed ends of each caster stem. The brackets
should rest securely on the carriage cross brace.
Secure the brackets to the carriage using two new
7/16-14 Thin Nylock Nuts from your kit.
NOTE: A Second Locking Mechanism can be
attached to the opposite side—
Order part # 999-0832-980SP.
23
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
SECTION C: MECHANICAL AND ELECTRICAL INFORMATION
LIBERTY BED MECHANICAL
LIBERTY BED ELECTRICAL
(Manufactured After
September 1, 2011; Serial
Numbers ≥ SN12020004096)
NOTE: ALL DIMENSIONS ARE ±.25 INCHES
• Overall Bed Length (with boards and wallsaver). 83"/86"
• Overall Bed Width (with boards). . . . . . . . . . . . . 36.00"
• Maximum Height*. . . . . . . . . . . . . . . . . . . . . . . . 24.50"
• Power/Frequency. . . . . . . . . . . . . . 120 Volt/ 50/60 Hz
• Minimum Height* . . . . . . . . . . . . . . . . . . . . . . . . . 9.95"
• Output Rating. . . . . . . . . . . . . . . . . . . . . . . . 24V IPX4
• Maximum Head/Back Deck Angle . . . . . . . . . . . . . 70°
• Overall Movement Draw. . . . . . . . . . . . . . . 2.00 Amps
• Maximum Knee/Foot Deck Angle. . . . . . . . . . . . . . 30°
• Maximum Safe Working Load . . . . . . . . . . . . . . 450 lb
WITH WEIGHT EVENLY DISTRIBUTED
- includes bedding, resident, support surface,
and all accessories
* Classification . . . . . . . . . . . . . . . . . . . Class 1, Type B
• Mass of bed (without assist devices or boards) =
182 lb
• Mode of Operations. . . . . . . . . . 10% Max. Duty Cycle
. . . . . . . . . . . . . . . . . . (2 minutes on/18 minutes off)
• Power (Electrical) Cord . . . . . . #18 AWG 3 Conductor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Type SJT
* Bed height calculated from floor surface to top of
sleep deck.
TYPICAL LIBERTY BED IDENTIFICATION LABELS
with Ilcon Electronics - LBT7174 or LBTL7174 (Models
Manufactured after September 1, 2011; Serial Numbers ≥ SN12020004096)
ETL GF HEALTH
INC.
Logo PRODUCTS,
ATLANTA, GA 30360
= 450 lbs
SAFE WORKING LOAD
LBT7174
IPX4
LIBERTY 701 SERIES
PATENT PENDING
LIBERTY 7174
MODEL NO. 701-0000-000000
701-0000-000000
MFG. DATE
09/01/11
VOLT
120
DUTY CYCLE - 2 min Continuous/18 min
MODE OF OPERATION - Intermittent
!
MODEL NO
HZ AMP TYPE
50/60
2
AC
SERIAL NO
000000000000
SERIAL LBT7
MFG DATE 09/01/11
Bed labels are an important part of
identifying the bed’s make and model
when ordering replacement parts. The
Serial Number is essential if you are
claiming parts or service under warranty.
These helpful labels can be located on the
main frame rails, immediately below the
sleep decks on either side of the bed.
Have this IMPORTANT information ready
when calling our Customer Service or
Technical Support staff at 770-368-4700;
it will allow us to better assist you and
quickly answer your questions and
concerns.
000000000000
LBT7174
GF Health Products, Inc. - www.grahamfield.com
24
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
LIBERTY BED ELECTRICAL COMPONENTS
(Manufactured After September 1, 2011)
Control Box
Part # 999-0848-300SP
Quantity = 1
Power Cord is not
detachable (hardwired
into side of Control Box)
Head Motor/Actuator
Part # 999-0844-052SP
Quantity = 1
Knee/Foot Motor/Actuator
Part # 999-0844-053SP
Quantity = 1
VENDOR MODEL HB00
HAND CONTROL PENDANT
Part # 999-0808-305SP
Quantity = 1
Bed also includes
Pendant Holster
Part # 999-0791-000SP
Quantity = 1
Adapter Cable to connect Hand
Control Pendant Cable to Control Box
Part # 999-0848-200SP
Quantity = 1
NOTE :
MOTOR CABLES AND
POWER CORD ARE NOT
DETACHABLE.
MOTOR CABLES ARE
HARD WIRED DIRECTLY
INTO MOTORS; POWER
CORD IS HARDWIRED
DIRECTLY INTO
CONTROL BOX.
Hi/Lo Motor/Actuator
Part # 999-0848-051SP
Quantity = 1
!
DO NOT use unauthorized parts, accessories, or adapters other than those specified/authorized by GF Health Products, Inc.
DO NOT open assemblies such as the Actuators, Hand Control Pendant, or Control Box. If unauthorized personnel perform
work on these components, the manufacturer’s warranty becomes void. NEVER operate the bed if a Power Cord or Plug is
damaged or not working properly. Contact qualified Service Personnel for examination and repair.
ALWAYS UNPLUG THE POWER CORD BEFORE PERFORMING MAINTENANCE ON THE BED.
GF Health Products, Inc. - www.grahamfield.com
25
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
SECTION D: SERVICE/REPLACEMENT PARTS
SERVICE/REPLACEMENT PART RECORD WITH ILCON ELECTRONICS
(Page 1)
DECKING
Part Number
Description
QTY
999-0844-920SP
Head/Back Deck and Hardware Pack
1 Deck
999-0844-930SP
OR - Foot Deck and Hardware Pack
1 Deck
999-0844-940SP
OR - Knee Deck and Hardware Pack
1 Deck
Deck Hardware Pack - INCLUDES . . .
1 Pkg
4
Clevis Pins
5
5/16" Retaining Rings (Deck Brackets)
2
12mm Retaining Ring (Cntrl Arms to Decks)
1
Installation Instruction Sheet
Order Date
Price
Order Date
Price
Order Date
Price
Order Date
Price
MOTORS (ACTUATORS)
Part Number
Description
QTY
999-0848-051SP
Hi/Lo Motor (Cable hard-wired) and Hardware Pack
1 Motor
999-0844-052SP
OR - Head Motor (Cable hard-wired) and Hardware Pack
1 Motor
999-0844-053SP
OR - Foot Motor (Cable hard-wired) and Hardware Pack
1 Motor
Motor Hardware Pack - INCLUDES . . .
1 Pkg
2
12mm Retaining Rings
2
Hair Pin Clips
2
Snap Rings
8
Standard Cable Ties
1
Installation Instruction Sheet
CONTROL BOX AND POWER CABLES
Part Number
Description
QTY
999-0848-300SP
Linak Control Box and Clip
1 Box
No Detachable Power Cord Available (Cord hard-wired to CB)
HAND CONTROL PENDANT
Part Number
Description
QTY
999-0808-305SP
Hand Control Pendant (Standard Model)
1 Pendant
999-0848-200SP
Pendant Adapter Cable
1 Cable
999-0791-000SP
Pendant Holster (Standard for all pendants)
1 Holster
GF Health Products, Inc. - www.grahamfield.com
26
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
SERVICE/REPLACEMENT PART RECORD WITH ILCON ELECTRONICS
(Page 2)
MISCELLANEOUS SERVICE BED PARTS
Part Number
Description
QTY
999-0822-012
Spanner Plates
1 Plate
999-0822-031
Pivot Channels
1 Unit
999-0822-036
Leveler Rods
1 Rod
100-8050-008
1/2" E-Style Retaining Rings (for Leveler Rods)
1 Ring
999-0822-001SP
Mattress Retainer
1 Unit
999-0822-180SP
Wireform Wallsaver
1 Unit
999-0822-083
18GA Ground Wire
1 Wire
100-5710-019
#10-24 x .375" HWHTC Ground Screws TYP23
1 Screw
100-1100-018
Standard Cable Ties
1 Tie
100-1100-060
Wing-Tip Cable Ties
1 Tie
Order Date
Price
Order Date
Price
Order Date
Price
CASTER CARRIAGE
Part Number
Description
QTY
999-0822-905G
Caster Carriage Weldment
1 Unit
100-6330-062SP
3" Twin Locking Caster with 7/16-14 Stems (LBT7174)
1 Caster
100-6330-061SP
3" Twin Non-Locking Caster with 7/16-14 Stems (LBTL7174)
1 Caster
999-0832-980SP
One-Step Locking Mechanism (LBTL7174)
1 Unit
100-6744-001
7/16-14 Nylon Lock Nuts (secure caster stems to frame)
1 Nut
CAPS AND PLUGS
Part Number
Description
QTY
NOTE: CAPS AND PLUGS CAN ONLY BE PURCHASED IN SETS OF 12
100-4700-015PK
1.00" x 1.00" Square Caps Pack
12/pkg
100-4700-017PK
1.00" x 2.00" Rectangular Caps Pack
12/pkg
999-0822-041PK
Black Tube Pivot Caps
12/pkg
FOR GENERAL CAP DIAGRAMS PLEASE SEE PAGES 30 AND 31
GF Health Products, Inc. - www.grahamfield.com
27
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
SERVICE/REPLACEMENT PARTS DIAGRAM - ELECTRONICS
HEAD BOARD
POWER CABLE
SECURED TO FRAME
WITH CABLE TIES
HEAD-END
HI/LO MOTOR
HEAD
END
CONTROL BOX ATTACHED TO
HI/LO MOTOR
FOOT/KNEE
MOTOR
SPECIAL
BOARD/PANEL
MOUNTING
BRACKETS
WIREFORM
WALLSAVER
FOOTBOARD
HAND CONTROL PENDANT CABLE
PLUGGED DIRECTLY INTO
CONTROL BOX AND CABLE TIED
TO EITHER SIDE OF SEAT PAN
FOOT
END
MATTRESS
RETAINER
• TO ORDER A REPLACEMENT
HI/LO MOTOR USE SERVICE PACK
999-0848-051SP (Includes motor,
mounting hardware, and installation
instruction sheet).
STANDARD CASTER CARRIAGE
WITH FOUR LOCKING CASTERS
• TO ORDER A REPLACEMENT
HEAD MOTOR USE SERVICE PACK
999-0844-052SP (Includes motor,
mounting hardware, and installation
instruction sheet).
• TO ORDER A REPLACEMENT
FOOT MOTOR USE SERVICE PACK
999-0844-053SP (Includes motor,
mounting hardware, and installation
instruction sheet).
• TO ORDER A REPLACEMENT
• TO ORDER A REPLACEMENT
• TO ORDER A REPLACEMENT
MATTRESS RETAINER USE PART
WALLSAVER USE PART NO.
CONTROL BOX USE PART NO.
NO. 999-0822-001SP.
999-0822-180SP .
999-0848-300SP (Includes control
box and mounting clip).
FOR ALL OTHER SERVICE/REPLACEMENT PARTS, SEE PAGES 26 AND 27.
WHEN ORDERING REPLACEMENT PARTS FROM CUSTOMER SERVICE,
HAVE THE BED SERIAL NUMBER AVAILABLE TO CONFIRM
WHETHER THE PART IS COVERED UNDER WARRANTY.
(SEE PAGE 24 FOR LOCATION OF SERIAL NUMBER ID LABEL.)
GF Health Products, Inc. - www.grahamfield.com
28
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
SECTION E: DECK/MECHANICAL SERVICE PARTS
SERVICE/REPLACEMENT PARTS DIAGRAM - DECKING
1
Main Frame Seat Pan
2
Head Deck Flange
3
Knee Deck Flange
4
Foot Deck Flange
5
5/16-18 Machine Screws
6
Self-Wrenching Nuts
7
Clevis Pins
8
Circle Cotters
9
E-Style Retaining Rings
8
8
7
Bottom
Pivot
Channel
HEAD/BACK DECK
999-0822-920G
7
Top
Pivot
Channel
10 Leveler Rods
KNEE DECK
999-0822-940G
MAIN FRAME
SEAT PAN
(Not a Service Part)
FOOT DECK
999-0822-930G
Foot Deck
Leveler Rod
Mounting Bracket
Insert E-Style Retaining
Ring onto end of Leveler
Rod after rod has been
inserted into frame
• TO ORDER A REPLACEMENT
HEAD DECK USE SERVICE PACK
999-0822-920SP (includes deck,
mounting hardware, and installation
instructions).
• TO ORDER A REPLACEMENT
KNEE DECK USE SERVICE PACK
999-0822-940SP (includes deck,
mounting hardware, and installation
instructions).
From the outside, insert
Leveler Rod through holes in
main frame rail and foot deck
mounting bracket on both
right and left sides of bed
• TO ORDER A REPLACEMENT
FOOT DECK USE SERVICE PACK
999-0822-930SP (includes deck,
mounting hardware, and
installation instructions).
• MISCELLANEOUS PARTS: a) Leveler Rod 999-0822-036, b) Retaining Ring 100-8031-001,
c) Machine Screw 100-5431-002, d) Self Nut 999-0032-010, e) Clevis Pin 999-0808-455, f)Circle Cotter 100-7518-001
WHEN ORDERING REPLACEMENT PARTS FROM CUSTOMER SERVICE,
HAVE THE BED SERIAL NUMBER AVAILABLE TO CONFIRM
WHETHER THE PART IS COVERED UNDER WARRANTY.
(SEE PAGE 24 FOR LOCATION OF SERIAL NUMBER ID LABEL.)
GF Health Products, Inc. - www.grahamfield.com
29
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
SERVICE/REPLACEMENT PARTS DIAGRAM MAIN FRAME CAPPING AND WING-STYLE CABLE TIES
1.00" Square
Tube End Cap
100-4700-015
1.00" x 2.00"
Rectangular
Tube End Cap
100-4700-017
HEAD END
(Right side of Bed)
1.00" Square
Tube End Cap
100-4700-015
1.00" Square
Tube End Cap
100-4700-015
1.00" Square
Tube End Cap
100-4700-015
Wing-Style Cable Ties
for Power Cord
100-4700-060
1.00” Square
Tube End Cap
100-4700-015
Main Frame
(Not a Service Part)
FOOT END
(Right side of Bed)
1.00" x 2.00"
Rectangular
Tube End Cap
100-4700-017
1.00" Square
Tube End Cap
100-4700-015
CAPS AND PLUGS ARE NOT COVERED UNDER WARRANTY
(PACKS OF 12 CAN BE ORDERED IN THE EVENT YOU DAMAGE OR LOSE
ANY BED CAPS OR PLUGS - SEE BOTTOM OF PAGE 30 FOR ORDER NUMBERS)
GF Health Products, Inc. - www.grahamfield.com
30
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
SERVICE/REPLACEMENT PARTS DIAGRAM CASTER CARRIAGE CAPPING AND CASTER PARTS—MODEL LBT7174
1.00" x 2.00"
Rectangular
Tube End Cap
100-4700-017
7/16-14
Nylock Nut
100-6744-001
3.00" Twin
Locking Caster
7/16-14 Stem
100-6330-062
CAPS AND PLUGS ARE NOT COVERED UNDER WARRANTY
(PACKS OF 12 CAN BE ORDERED IN THE EVENT YOU DAMAGE OR LOSE
ANY BED CAPS OR PLUGS - SEE BOTTOM OF PAGE 30 FOR ORDER NUMBERS)
GF Health Products, Inc. - www.grahamfield.com
31
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
SECTION F: TROUBLESHOOTING
ELECTRONIC TROUBLESHOOTING QUICK REFERENCE
The Liberty Bed uses a 3-motor system with ILCON electronics (after
September 1, 2011). To troubleshoot the Liberty Bed, follow the steps below
in the order shown.
NO POWER
1. Verify that there is power in the wall outlet.
2. Unplug Power Cord and check the following:
a. Check Power Cord for damage or pinching.
b. Check short black Control Box Cable for
damage or pinching.
c. If any cables are damaged - replace
immediately.
HAND CONTROL PENDANT DOESN’T WORK
1. Check All Pendant and Cable connections and
retest.
2. Unplug Power Cord.
3. Unplug Hand Control Pendant from the Adapter
Cable. Use a new Adapter Cable you know
works from another bed. Plug in the power cord
and test:
a. If Pendant works - replace Adapter Cable.
b. If Pendant does not work - unplug the
Pendant from Control Box. Use a new
Pendant you know works from another bed.
Plug in the power cord and test:
i. If Pendant works - replace old Pendant.
ii. If Pendant does not work - replace
Control Box.
GF Health Products, Inc. - www.grahamfield.com
32
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
ELECTRONIC TROUBLESHOOTING QUICK REFERENCE
HEAD OR FOOT MOTOR MALFUNCTIONS
(DECK DOES NOT GO UP AND/OR DOWN)
1. Check all Motor Cable connections.
2. Check Motor condition - cracked housing, scratches,
bent shaft, etc.
3. Hi/Lo and Foot work, but Head does not:
a. Unplug Power Cord.
b. Switch Head and Foot Motor Cables at the
Control Box.
c. Replug Power Cord and test.
4. Hi/Lo and Head work, but Foot does not:
a. Unplug Power Cord.
b. Switch Foot and Head Motor Cables at the
Control Box.
c. Replug Power Cord and test.
5. Motor grinds loudly - replace Motor.
HI/LO MOTOR MALFUNCTIONS (ENTIRE
BED DOES NOT GO UP AND/OR DOWN)
1. Check All Motor Cable connections.
2. Check Motor condition - cracked housing, scratches,
bent shaft, etc.
3. Head and Foot Motor work, but Hi/Lo does not:
a. Unplug Power Cord.
b. Unplug Hi/Lo Cable at Control Box, and plug into
Head port.
c. Replug Power Cord and test.
4. If Hi/Lo works - replace Control Box.
5. If Hi/Lo doesn’t work, or grinds - replace Hi/Lo Motor.
CONTROL BOX MALFUNCTIONS
1. Check all Motor Cables and Power Cord
connections.
2. Hi/Lo Motor works, but Head or Foot does not (see
Head & Foot Motor Troubleshooting above). If
determined that port is bad, replace Control Box.
3. Head and Foot Motors work, But Hi/Lo does not (see
Hi/Lo Motor Troubleshooting above). If determined
that port is bad, replace Control Box.
If the problem continues, contact Technical Support
at 770-368-4700.
GF Health Products, Inc. - www.grahamfield.com
Head Motor
999-0844-052SP
Foot Motor
999-0844-053SP
Hi/Lo Motor
999-0848-051SP
Control Box
999-0848-300SP
This Port Not Used
Foot Motor Cable Port
Head Motor Cable Port
Hi/Lo Motor Cable Port
Control Cable Port
(999-0848-200 connects to Pendant Cable)
33
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
LIMITED WARRANTY
SCOPE OF WARRANTY
GF Health Products, Inc. (“GF”) warrants to the original purchaser only that it will replace or repair components, at GF’s
sole discretion, that are defective in material or workmanship under normal use and service. All warranties are conditioned
upon the proper use of the products strictly in accordance with good commercial practice and applicable GF instructions
and manuals, including proper use and maintenance. To the extent that a component is warranted by a third party, GF
conveys all of its rights under that warranty to the original purchaser, to the extent permitted.
This limited warranty shall only apply to defects that are reported to GF’s customer service team within the applicable
warranty period and which, upon examination by GF or its authorized representative, prove to be a warranty item. This
limited warranty is not transferable.
The warranted components and time period are set forth below:
Main Frame:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ten years
Control Box and Actuator Motors: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . two years
Hand Control Pendant, Staff Control, and Cabling. . . . . . . . . . . . . . . . . . . . . . . one year
All other durable components not listed above:. . . . . . . . . . . . . . . . . . . . . . . . . two years
Subsequent service parts under warranty until the original warranty set forth above expires, or for one year, whichever
is greater.
The applicable warranty period shall commence from date of shipment to the original customer, unless there is an
expiration date on the component in which case the warranty shall expire on the earlier of warranty period or the
expiration date.
OBTAINING WARRANTY SERVICE
This limited warranty shall only apply to defects that are reported to the Distributor from whom the Customer purchased
the product within the applicable warranty period. If there is not a Distributor, you must contact GF directly by calling
770-368-4700, sending a fax request to 770-368-2386, or by e-mailing a request to [email protected] Specific
directions will be provided by the Customer Service Representative. Failure to abide by the specific directions will result in
denial of the warranty claim.
EXCLUSIONS
The warranty does not cover and GF shall not be liable for the following:
1) Defects, damage, or other conditions caused, in whole or in part, by misuse, abuse, negligence, alteration, accident,
freight damage, tampering or failure to seek and obtain repair or replacement in a timely manner;
2) Products which are not installed, used, or properly cleaned and maintained as required in the official manual for the
applicable product;
3) Products considered to be of a non-durable nature including, but not limited to: casters, filters, fuses, gaskets,
lubricants, and charts;
4) Accessories or parts not provided by GF;
5) Charges by anyone for adjustments, repairs, replacement parts, installation or other work performed upon or in
connection with such products which are not expressly authorized in writing, in advance, by GF;
6) Any labor or shipping charges incurred in the replacement part installation or repair;
7) Costs and expenses of regular maintenance and cleaning; and
8) Representations and warranties made by any person or entity other than GF.
GF Health Products, Inc. - www.grahamfield.com
34
Liberty Series Service Manual 999-0822-190G
LIBERTY SERIES
ENTIRE WARRANTY, EXCLUSIVE REMEDY AND CONSEQUENTIAL DAMAGES DISCLAIMER
THIS WARRANTY IS GF’S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED. GF MAKES NO IMPLIED WARRANTIES OF ANY KIND INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IF ANY MODEL OR SAMPLE WAS SHOWN TO THE CUSTOMER, SUCH MODEL OR SAMPLE WAS USED MERELY
TO ILLUSTRATE THE GENERAL TYPE AND QUALITY OF THE PRODUCT AND NOT TO REPRESENT THAT THE
PRODUCT WOULD NECESSARILY CONFORM TO THE MODEL OR SAMPLE IN ALL RESPECTS.
THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PARTS. GF SHALL
NOT BE LIABLE FOR AND HEREBY DISCLAIMS ANY DIRECT, SPECIAL, INDIRECT, INCIDENTAL, EXEMPLARY
OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO: DAMAGES FOR LOSS OF PROFITS OR
INCOME, LOSS OF USE, DOWNTIME, COVER, OR EMPLOYEE OR INDEPENDENT CONTRACTOR WAGES,
PAYMENTS AND BENEFITS.
The warranties contained herein contain all the representations and warranties with respect to the subject matter of this
document, and supersede all prior negotiations, agreements and understandings with respect thereto. The recipient of
this document hereby acknowledges and represents that it has not relied on any representation, assertion, guarantee,
warranty, collateral contract or other assurance, except those set out in this document.
For additional information on this product or this warranty, contact a GF Customer Service Representative.
NOTES:
1) Additional terms and conditions may apply.
2) Freight claims must be notated on the appropriate shipping documents and must be made with immediacy.
International, federal and state regulations govern specific requirements for freight claims. Failure to abide by those
regulations may result in a denial of the freight claim. GF will assist you in filing the freight claim.
3) Claims for any short shipment must be made within three (3) days of the invoice date.
GF Health Products, Inc.
2935 Northeast Parkway
Atlanta, GA 30360
Tel 770-368-4700
Fax 770-368-2386
www.grahamfield.com
If you have questions regarding a bed’s warranty,
contact Basic American Medical Products at 770-368-4700.
GF Health Products, Inc. - www.grahamfield.com
35
Liberty Series Service Manual 999-0822-190G
www.grahamfield.com
GF Health Products, Inc.
2935 Northeast Parkway
Atlanta, Georgia 30360
Customer Service: phone 770-368-4700, fax 770-368-2386
© 2010 GF Health Products, Inc., All Rights Reserved
Basic American Medical Products
is a registered trademark of
GF Health Products, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement