ThinkPad Z60t Hardware Maintenance Manual

ThinkPad Z60t Hardware Maintenance Manual
ThinkPad® Z60t
Hardware Maintenance Manual
October 2007
This manual supports:
ThinkPad Z60t
(MT 2511, 2512, 2513, and 2514)
ThinkPad® Z60t
Hardware Maintenance Manual
Note
Before using this information and the product it supports, be sure to read the general information under “Notices” on page
134.
Second Edition (October 2007)
© Copyright Lenovo 2006, 2007. All rights reserved.
LENOVO products, data, computer software, and services have been developed exclusively at private expense and
are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted
rights to use, reproduction and disclosure.
LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered
pursuant a General Services Administration ″GSA″ contract, use, reproduction, or disclosure is subject to restrictions
set forth in Contract No. GS-35F-05925.
Contents
About this manual . . . . . . . . . . 1
Introduction . . . . . . . . . . . . . 3
Important service information . . . . . . . . 3
Strategy for replacing FRUs . . . . . . . . . 3
Strategy for replacing a hard disk drive . . . . 4
Important notice for replacing a system board . . 4
How to use error messages . . . . . . . . 4
Strategy for replacing FRUs for CTO, CMV, and GAV 4
Product definition . . . . . . . . . . . 4
FRU identification for CTO, CMV, and GAV
products . . . . . . . . . . . . . . . 5
Important information about replacing RoHS
compliant FRUs . . . . . . . . . . . . . 6
Diskette compatibility matrix . . . . . . . . . 7
Safety notices: multilingual translations . . . . . 7
Safety information . . . . . . . . . . . . 13
General safety . . . . . . . . . . . . 13
Electrical safety . . . . . . . . . . . . 13
Safety inspection guide . . . . . . . . . 15
Handling devices that are sensitive to
electrostatic discharge . . . . . . . . . . 16
Grounding requirements . . . . . . . . . 16
Laser compliance statement . . . . . . . . . 17
General descriptions . . . . . . . . . 19
Read this first . . . . . . . . . . . .
What to do first . . . . . . . . . . .
Related service information . . . . . . . .
Service Web site . . . . . . . . . . .
Restoring the pre-installed system . . . . .
Passwords . . . . . . . . . . . . .
Power management . . . . . . . . .
Checkout guide . . . . . . . . . . . .
Testing the computer . . . . . . . . .
Detecting system information with PC-Doctor .
Power system checkout . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
19
19
21
21
21
21
24
26
26
29
30
ThinkPad Z60t . . . . . . . . . . . 33
Product overview . .
Specifications . . .
Status indicators . .
FRU tests . . . .
Fn key combinations
Symptom-to-FRU index
Numeric error codes
Error messages . .
Beep symptoms . .
No-beep symptoms .
.
.
.
.
.
.
.
.
.
.
© Copyright Lenovo 2006, 2007
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
34
34
36
39
41
44
44
48
49
49
LCD-related symptoms . . . . . . . . . 50
Intermittent problems . . . . . . . . . . 51
Undetermined problems . . . . . . . . . 51
FRU replacement notices . . . . . . . . . . 52
Screw notices . . . . . . . . . . . . . 52
Retaining serial numbers . . . . . . . . . 52
Removing and replacing a FRU . . . . . . . . 55
1010 Battery pack . . . . . . . . . . . 56
1020 Ultrabay Slim device . . . . . . . . 57
1030 Hard disk drive cover, hard disk drive, and
hard disk drive rubber rails . . . . . . . . 58
1040 Palm rest or palm rest with fingerprint
reader . . . . . . . . . . . . . . . 60
1050 DIMM . . . . . . . . . . . . . 62
1060 Keyboard . . . . . . . . . . . . 63
1070 Modem daughter card (MDC-1.5) . . . . 65
1080 PCI Express Mini card for wireless WAN . . 67
1090 PCI Express Mini card for wireless LAN . . 69
1100 Backup battery . . . . . . . . . . 71
1110 Keyboard bezel . . . . . . . . . . 72
1120 Speaker assembly . . . . . . . . . 74
1130 Fan assembly . . . . . . . . . . . 76
1140 CPU . . . . . . . . . . . . . . 78
1150 Wireless WAN antenna (DIV) . . . . . . 79
1160 LCD assembly . . . . . . . . . . . 80
1170 Base cover . . . . . . . . . . . . 83
1180 USB/S-video sub card with cable . . . . 86
1190 MG (Magnesium) frame . . . . . . . 87
1200 System board and PC Card slot assembly
92
2010 LCD front bezel . . . . . . . . . . 97
2020 Inverter card . . . . . . . . . . . 99
2030 Bluetooth daughter card (BDC-2) . . . . 100
2040 Wireless WAN antenna cable (MAIN) . . 102
2050 LCD panel, LCD cable, and hinges . . . 105
2060 LCD rear cover and wireless LAN antenna
cables . . . . . . . . . . . . . . . 108
Locations . . . . . . . . . . . . . . . 114
Front view . . . . . . . . . . . . . 114
Rear view . . . . . . . . . . . . . 115
Bottom view . . . . . . . . . . . . . 116
Parts list . . . . . . . . . . . . . . . 117
Overall . . . . . . . . . . . . . . 118
LCD FRUs . . . . . . . . . . . . . 126
Keyboard . . . . . . . . . . . . . . 128
Recovery CDs . . . . . . . . . . . . 129
Miscellaneous parts . . . . . . . . . . 131
AC adapters . . . . . . . . . . . . . 132
Common parts list. . . . . . . . . . . 132
Notices . . . . . . . . . . . . . . . 134
Trademarks . . . . . . . . . . . . . . 135
iii
iv
MT 2511, 2512, 2513, and 2514
About this manual
This manual contains service and reference information for ThinkPad® Z60t (MT
2511, 2512, 2513, and 2514) products. Use this manual along with the advanced
diagnostic tests to troubleshoot problems.
The manual is divided into sections as follows:
v The common sections provide general information, guidelines, and safety
information required in servicing computers.
v The product-specific section includes service, reference, and product-specific
parts information.
Important
This manual is intended for trained service personnel who are familiar with
ThinkPad products. Use this manual along with the advanced diagnostic tests
to troubleshoot problems effectively.
Before servicing a ThinkPad product, be sure to review the safety information
under “Safety notices: multilingual translations” on page 7, “Safety
information” on page 13, and “Laser compliance statement” on page 17.
© Copyright Lenovo 2006, 2007
1
2
MT 2511, 2512, 2513, and 2514
Introduction
Important service information
Important
BIOS and device driver fixes are customer-installable. The BIOS and device
drivers are posted on the customer support site http://www.lenovo.com/
support
Advise customers to contact the Customer Support Center at 800-426-7378 if
they need assistance in obtaining or installing any software fixes, drivers, and
BIOS downloads.
Customers in Canada should call the Customer Support Center at
800-565-3344 for assistance or download information.
Strategy for replacing FRUs
Before replacing parts
Make sure that all software fixes, drivers, and BIOS downloads are installed
before replacing any FRUs listed in this manual.
After a system board is replaced, ensure that the latest BIOS is loaded to the
system board before completing the service action.
To download software fixes, drivers, and BIOS, do as follows:
1. Go to http://www.lenovo.com/support
2. Enter the product number of the computer or press Auto-detect button on
the screen.
3. Select Downloads and drivers.
4. Follow the directions on the screen and install the necessary software.
Use the following strategy to prevent unnecessary expense for replacing and
servicing FRUs:
v If you are instructed to replace a FRU but the replacement does not correct the
problem, reinstall the original FRU before you continue.
v Some computers have both a processor board and a system board. If you are
instructed to replace either the processor board or the system board, and
replacing one of them does not correct the problem, reinstall that board, and
then replace the other one.
v If an adapter or a device consists of more than one FRU, any of the FRUs may
be the cause of the error. Before replacing the adapter or device, remove the
FRUs, one by one, to see if the symptoms change. Replace only the FRU that
changed the symptoms.
© Copyright Lenovo 2006, 2007
3
Important service information
Attention: The setup configuration on the computer you are servicing may have
been customized. Running Automatic Configuration may alter the settings. Note
the current configuration settings (using the View Configuration option); then,
when service has been completed, verify that those settings remain in effect.
Strategy for replacing a hard disk drive
Always try to run a low-level format before replacing a hard disk drive. This will
cause all customer data on the hard disk to be lost. Be sure that the customer has a
current backup of the data before doing this task.
Attention: The drive startup sequence in the computer you are servicing may
have been changed. Be extremely careful during write operations such as copying,
saving, or formatting. If you select an incorrect drive, data or programs can be
overwritten.
Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper
handling of a system board can cause damage to those components, and may
cause a system malfunction.
Attention: When handling a system board:
v Do not drop a system board or apply any excessive force to it.
v Avoid rough handling of any kind.
v Avoid bending a system board and hard pushing to prevent cracking at each
BGA (Ball Grid Array) chipset.
How to use error messages
Use the error codes displayed on the screen to diagnose failures. If more than one
error code is displayed, begin the diagnosis with the first error code. Whatever
causes the first error code may also cause false error codes. If no error code is
displayed, see whether the error symptom is listed in the Symptom-to-FRU Index
for the computer you are servicing.
Strategy for replacing FRUs for CTO, CMV, and GAV
Product definition
Dynamic Configure To Order (CTO)
This provides the ability for a customer to configure an IBM® or a LenovoTM
solution from an eSite, and have this configuration sent to fulfillment, where it is
built and shipped directly to the customer. The machine label, Product Entitlement
Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit
MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
Custom Model Variant (CMV)
This is a unique configuration that has been negotiated between IBM or Lenovo
and the customer. A unique 4-digit MT and 3-digit model is provided to the
customer to place orders (Example: 1829-W15). A CMV is a special bid offering.
Therefore, it is NOT generally announced.
v The MTM portion of the machine label is the 4-digit MT and 3-digit model,
where model = “CTO” (Example: 1829-CTO). The PRODUCT ID portion of the
machine label is the 4-digit MT and 3-digit CMV model (Example: 1829-W15).
4
MT 2511, 2512, 2513, and 2514
Important service information
v The PEW record is the 4-digit MT and 3-digit model, where model = “CTO”
(Example: 1829-CTO).
v eSupport will show both the CTO and CMV machine type models (Example:
1829-CTO and 1829-W15 will be found on the eSupport site.)
v The HMM will have the 4-digit MT and 3-digit CTO model only (Example:
1829-CTO). Again, CMVs are custom models and are not found in the HMM.
General Announce Variant (GAV)
This is a standard model (fixed configuration). GAVs are announced and offered to
all customers. The MTM portion of the machine label is a 4-digit MT and 3-digit
model, where model = a “fixed part number”, not “CTO” (Example: 1829-F1U).
Also, PEW, eSupport, and the HMM will list these products under the same fixed
model number.
FRU identification for CTO, CMV, and GAV products
There are three information resources to identify which FRUs are used to support
CTO, CMV, and GAV products. These sources are PEW, eSupport, and the HMM.
Using PEW
v PEW is the primary source for identifying FRU part numbers and FRU
descriptions for the key commodities for CTO, CMV and GAV products at a MT
- serial number level. An example of key commodities are hard disk drives,
system boards, microprocessors, Liquid Crystal Displays (LCDs), and memory.
v Remember, all CTO and CMV products are loaded in PEW under the 4-digit MT
and 3-digit model, where model = “CTO” (Example: 1829-CTO). GAVs are
loaded in PEW under the 4-digit MT and 3-digit model, where model = a “fixed
part number”, not “CTO” (Example: 1829-F1U).
v PEW can be accessed at the following Web site:
http://w3-3.ibm.com/pc/entitle
Customers can also access PEW via
http://www-307.ibm.com/pc/support/site.wss/product.do?template=/warranty/
warranty.vm&sitestyle=lenovo
Select Warranty lookup. Input the MT and the Serial number and the list of key
commodities will be returned in the PEW record under COMPONENT
INFORMATION.
v Business Partners using Eclaim will access PEW when performing Entitlement
Lookup. Business Partners will enter Loc ID, MT and Serial, and the key
commodities will be returned in the Eclaim record under SYSTEM DETAILS.
v Authorized IBM Business Partners can access Eclaim at the following Web site:
https://wca.eclaim.com
Using eSupport
For Key Commodities (Examples - hard disk drive, system board,
microprocessor, LCD, and memory)
v eSupport can be used to view the list of key commodities built in a particular
machine serial (this is the same record found in PEW).
v eSupport can be accessed at the following Web site: http://www.lenovo.com/
support
v To view the key commodities, click on PARTS INFORMATION, then PARTS
LOOKUP. Type in the model type and serial number. The key commodities will
be returned in the eSupport record under PARTS SHIPPED WITH YOUR
SYSTEM.
Introduction
5
Important service information
For the Remaining FRUs (the complete list of FRUs at the MT Model level)
v eSupport can be used to view the complete list of FRUs for a machine type and
model.
v To view the complete list of FRUs, type in the machine type and model
(Example: 1829-CTO) under QUICK PATH. Under “View by Document Type”
select PARTS INFORMATION. Under “Filter by Category” select SERVICE
PARTS. Under “Parts Information by Date” select SYSTEM SERVICE PARTS. The
list of service parts by description, with applicable machine type model and FRU
will be displayed.
Using the HMM
Use the HMM as a back-up to PEW and eSupport to view the complete list of
FRUs at the MT Model level.
Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and Electronic
Equipment Directive (2002/95/EC) is a European Union legal requirement
affecting the global electronics industry. RoHS requirements must be
implemented on Lenovo products placed on the market and sold in the
European Union after June 2006. Products on the market before June 2006 are
not required to have RoHS compliant parts. If the original FRU parts are non
compliant, replacement parts can also be non compliant. In all cases if the
original FRU parts are RoHS compliant the replacement part must also be RoHS
compliant.
Note: RoHS and non-RoHS FRU part numbers with the same fit and function are
identified with unique FRU part numbers.
Lenovo plans to transition to RoHS compliance well before the implementation
date and expects its suppliers to be ready to support Lenovo's requirements and
schedule in the EU. Products sold in 2005 and 2006, will contain some RoHS
compliant FRUs. The following statement pertains to these products and any
product Lenovo produces containing RoHS compliant FRUs.
RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS
implementation date, failed RoHS compliant parts must always be replaced using
RoHS compliant FRUs, so only the FRUs identified as compliant in the system
HMM or direct substitutions for those FRUs may be used.
Products marketed before June 2006
Products marketed after June 2006
Current or original
part
Replacement FRU
Current or original
part
Replacement FRU
Non-RoHS
Can be Non-RoHS
Must be RoHS
Must be RoHS
Non-RoHS
Can be RoHS
Non-RoHS
Can sub to RoHS
RoHS
Must be RoHS
Note: A direct substitution is a part with a different FRU part number that is
automatically shipped by the distribution center at the time of the order.
6
MT 2511, 2512, 2513, and 2514
Diskette compatibility matrix
Diskette compatibility matrix
The compatibility of each of the drives with the diskettes for it is as follows:
Diskette
drive
Diskette
capacity
Compatibility
3.5-inch
1.0 MB
Read and write
2.0 MB
Read and write
4.0 MB
Not compatible
Safety notices: multilingual translations
In this manual, safety notices appear in English with a page number reference to
the appropriate multilingual, translated safety notice found in this section.
The following safety notices are provided in English, French, German, Hebrew,
Italian, and Spanish.
Safety notice 1
Before the computer is powered on after FRU replacement, make sure all screws, springs,
and other small parts are in place and are not left loose inside the computer. Verify this
by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes
can cause electrical shorts.
Avant de remettre l’ordinateur sous tension après remplacement d’une unité en clientèle,
vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour
ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect ne se produit. Des pièces
métalliques ou des copeaux de métal pourraient causer un court-circuit.
Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß
sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im
Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche
geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen.
Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di una FRU,
accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni siano nella
corretta posizione e non siano sparse all’interno dell’elaboratore. Verificare ciò scuotendo
l’elaboratore e prestando attenzione ad eventuali rumori; eventuali parti o pezzetti
metallici possono provocare cortocircuiti pericolosi.
Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los
tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran
sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles
ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos.
Introduction
7
Safety notices
Safety notice 2
DANGER
Some standby batteries contain a small amount of nickel and cadmium. Do not
disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it.
Dispose of the battery as required by local ordinances or regulations. Use only the
battery in the appropriate parts listing. Use of an incorrect battery can result in
ignition or explosion of the battery.
Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez
pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne les mettez pas en
court-circuit. Pour les mettre au rebut, conformez-vous à la réglementation en vigueur.
Lorsque vous remplacez la pile de sauvegarde ou celle de l’horloge temps réel, veillez
à n’utiliser que les modèles cités dans la liste de pièces détachées adéquate. Une
batterie ou une pile inappropriée risque de prendre feu ou d’exploser.
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann
geringe Mengen Nickel und Cadmium enthalten. Sie darf nur durch die Verkaufsstelle
oder den IBM Kundendienst ausgetauscht werden. Sie darf nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Die
Batterie kann schwere Verbrennungen oder Verätzungen verursachen. Bei der
Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen der
Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden, der in der
Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder
Explosion führen.
Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio. Non
smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle. Smaltirle
secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni
locali). Quando si sostituisce la batteria dell’RTC (real time clock) o la batteria di
supporto, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di
una batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria
stessa.
Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio. No
las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite.
Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se
encuentren en la lista de piezas. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.
8
MT 2511, 2512, 2513, and 2514
Safety notices
Safety notice 3
DANGER
The battery pack contains small amounts of nickel. Do not disassemble it, throw it
into fire or water, or short-circuit it. Dispose of the battery pack as required by local
ordinances or regulations. Use only the battery in the appropriate parts listing when
replacing the battery pack. Use of an incorrect battery can result in ignition or
explosion of the battery.
La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n’utiliser que
les modèles cités dans la liste de pièces détachées adéquate. En effet, une batterie
inappropriée risque de prendre feu ou d’exploser.
Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei
der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen
der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist.
Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.
La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco o
nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR 915/82,
successive disposizioni e disposizioni locali). Quando si sostituisce la batteria,
utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di una
batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.
Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni recargue,
ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como dispone la
normativa local. Utilice sólo baterías que se encuentren en la lista de piezas al
sustituir la batería. La utilización de una batería no apropiada puede provocar la
ignición o explosión de la misma.
Introduction
9
Safety notices
Safety notice 4
DANGER
The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it,
remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate
it, or expose its cell contents to water. Dispose of the battery as required by local
ordinances or regulations. Use only the battery in the appropriate parts listing. Use of
an incorrect battery can result in ignition or explosion of the battery.
La pile de sauvegarde contient du lithium. Elle présente des risques d’incendie,
d’explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son connecteur
polarisé et ne la démontez pas. Ne l’exposez pas à une temperature supérieure à 100°C,
ne la faites pas brûler et n’en exposez pas le contenu à l’eau. Mettez la pile au rebut
conformément à la réglementation en vigueur. Une pile inappropriée risque de
prendre feu ou d’exploser.
Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren
oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht
aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr Inhalt
nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte
Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen Bestimmungen
für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien des Typs
verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien
kann zu Entzündung oder Explosion führen.
La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare
gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla,
riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla
in acqua. Smaltirla secondo la normativa in vigore (DPR 915/82, successive
disposizioni e disposizioni locali). L’impiego di una batteria non adatta potrebbe
determinare l’incendio o l’esplosione della batteria stessa.
La batería de repuesto es una batería de litio y puede provocar incendios, explosiones
o quemaduras graves. No la recargue, ni quite el conector polarizado, ni la desmonte,
ni caliente por encima de los 100°C (212°F), ni la incinere ni exponga el contenido de
sus celdas al agua. Deséchela tal como dispone la normativa local.
10
MT 2511, 2512, 2513, and 2514
Safety notices
Safety notice 5
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your
hands, immediately wash the affected areas with water for at least 15 minutes. Seek
medical care if any symptoms from the fluid are present after washing.
Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux
ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze
minutes. Consultez un médecin si des symptômes persistent après le lavage.
Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die
örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas
und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den
Boden fällt. Wenn der Bildschirm beschädigt ist und die darin befindliche Flüssigkeit in
Kontakt mit Haut und Augen gerät, sollten die betroffenen Stellen mindestens 15
Minuten mit Wasser abgespült und bei Beschwerden anschließend ein Arzt aufgesucht
werden.
Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto entrasse in
contatto con gli occhi o le mani, lavare immediatamente le parti interessate con acqua
corrente per almeno 15 minuti; poi consultare un medico se i sintomi dovessero
permanere.
Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos,
lave inmediatamente las áreas afectadas con agua durante 15 minutos como mínimo.
Obtenga atención medica si se presenta algún síntoma del fluido despues de lavarse.
Safety notice 6
DANGER
To avoid shock, do not remove the plastic cover that protects the lower part of the
inverter card.
Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique
protégeant la partie inférieure de la carte d’alimentation.
Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der
Spannungswandlerplatine umgibt, nicht entfernen.
Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la
parte inferiore della scheda invertitore.
Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la
tarjeta invertida.
Introduction
11
Safety notices
Safety notice 7
DANGER
Though the main batteries have low voltage, a shorted or grounded battery can
produce enough current to burn personnel or combustible materials.
Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise
à la masse d’une batterie peut produire suffisamment de courant pour brûler des
matériaux combustibles ou causer des brûlures corporelles graves.
Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei
Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu
entzünden oder Verletzungen bei Personen hervorzurufen.
Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in corto
circuito o a massa può fornire corrente sufficiente da bruciare materiali combustibili o
provocare ustioni ai tecnici di manutenzione.
Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o
con contacto a tierra puede producir la corriente suficiente como para quemar material
combustible o provocar quemaduras en el personal.
Safety notice 8
DANGER
Before removing any FRU, power off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any interconnecting
cables.
Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension,
débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la
batterie et déconnectez tous les cordons d’interface.
Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der
Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU entfernt
wird.
Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese elettriche
tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi di
interconnessione.
Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas
de corriente eléctrica, quite la batería y, a continuación, desconecte cualquier cable de
conexión entre dispositivos.
12
MT 2511, 2512, 2513, and 2514
Safety information
Safety information
The following section presents safety information with which you need to be
familiar before you service a ThinkPad computer.
General safety
Follow these rules to ensure general safety:
v Observe good housekeeping in the area of the machines during and after
maintenance.
v When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to
lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes
the strain from the muscles in your back. Do not attempt to lift any object that
weighs more than 16 kg (35 lb) or that you think is too heavy for you.
v Do not perform any action that causes hazards to the customer, or that makes
the equipment unsafe.
v Before you start the machine, make sure that other service representatives and
the customer’s personnel are not in a hazardous position.
v Place removed covers and other parts in a safe place, away from all personnel,
while you are servicing the machine.
v Keep your toolcase away from walk areas so that other people will not trip over
it.
v Do not wear loose clothing that can be trapped in the moving parts of a
machine. Make sure that your sleeves are fastened or rolled up above your
elbows. If your hair is long, fasten it.
v Insert the ends of your necktie or scarf inside clothing or fasten it with a
nonconductive clip, about 8 centimeters (3 inches) from the end.
v Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your
clothing.
Attention: Metal objects are good electrical conductors.
v Wear safety glasses when you are hammering, drilling, soldering, cutting wire,
attaching springs, using solvents, or working in any other conditions that might
be hazardous to your eyes.
v After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
v Reinstall all covers correctly before returning the machine to the customer.
v Fan louvers on the machine help to prevent overheating of internal components.
Do not obstruct fan louvers or cover them with labels or stickers.
Electrical safety
Observe the following rules when working on electrical equipment.
Introduction
13
Safety information
Important
Use only approved tools and test equipment. Some hand tools have handles
covered with a soft material that does not insulate you when working with
live electrical currents.
Many customers have, near their equipment, rubber floor mats that contain
small conductive fibers to decrease electrostatic discharges. Do not use this
type of mat to protect yourself from electrical shock.
v Find the room emergency power-off (EPO) switch, disconnecting switch, or
electrical outlet. If an electrical accident occurs, you can then operate the switch
or unplug the power cord quickly.
v Do not work alone under hazardous conditions or near equipment that has
hazardous voltages.
v Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing Field Replaceable Units (FRUs)
v Before you start to work on the machine, unplug the power cord. If you cannot
unplug it, ask the customer to power-off the wall box that supplies power to the
machine, and to lock the wall box in the off position.
v If you need to work on a machine that has exposed electrical circuits, observe the
following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.
Attention: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical equipment;
keep the other hand in your pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete
circuit. By observing the above rule, you may prevent a current from passing
through your body.
– When using testers, set the controls correctly and use the approved probe
leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you
from grounds such as metal floor strips and machine frames.
v
v
v
v
v
14
Observe the special safety precautions when you work with very high voltages;
Instructions for these precautions are in the safety sections of maintenance
information. Use extreme care when measuring high voltages.
Regularly inspect and maintain your electrical hand tools for safe operational
condition.
Do not use worn or broken tools and testers.
Never assume that power has been disconnected from a circuit. First, check that it
has been powered off.
Always look carefully for possible hazards in your work area. Examples of these
hazards are moist floors, nongrounded power extension cables, power surges,
and missing safety grounds.
Do not touch live electrical circuits with the reflective surface of a plastic dental
mirror. The surface is conductive; such touching can cause personal injury and
machine damage.
MT 2511, 2512, 2513, and 2514
Safety information
v Do not service the following parts with the power on when they are removed
from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
v If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially
unsafe conditions. As each machine was designed and built, required safety items
were installed to protect users and service personnel from injury. This guide
addresses only those items. You should use good judgment to identify potential
safety hazards due to attachment of non-ThinkPad features or options not covered
by this inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent
hazard could be and whether you can continue without first correcting the
problem.
Consider these conditions and the safety hazards they present:
v Electrical hazards, especially primary power (primary voltage on the frame can
cause serious or fatal electrical shock)
v Explosive hazards, such as a damaged CRT face or a bulging capacitor
v Mechanical hazards, such as loose or missing hardware
To determine whether there are any potentially unsafe conditions, use the
following checklist at the beginning of every service task. Begin the checks with
the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure
third-wire ground continuity for 0.1 ohm or less between the external
ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-ThinkPad alterations. Use good judgment as to the
safety of any non-ThinkPad alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings,
contamination, water or other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
Introduction
15
Safety information
9. Check that the power-supply cover fasteners (screws or rivets) have not been
removed or tampered with.
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be
considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when
there is a difference in charge between objects. Protect against ESD damage by
equalizing the charge so that the machine, the part, the work mat, and the person
handling the part are all at the same charge.
Notes
1. Use product-specific ESD procedures when they exceed the requirements
noted here.
2. Make sure that the ESD protective devices you use have been certified
(ISO 9000) as fully effective.
When handling ESD-sensitive parts:
v Keep the parts in protective packages until they are inserted into the product.
v Avoid contact with other people while handling the part.
v Wear a grounded wrist strap against your skin to eliminate static on your body.
v Prevent the part from touching your clothing. Most clothing is insulative and
retains a charge even when you are wearing a wrist strap.
v Use the black side of a grounded work mat to provide a static-free work surface.
The mat is especially useful when handling ESD-sensitive devices.
v Select a grounding system, such as those listed below, to provide protection that
meets the specific service requirement.
Note
The use of a grounding system to guard against ESD damage is desirable
but not necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire
ground.
– When working on a double-insulated or battery-operated system, use an ESD
common ground or reference point. You can use coax or connector-outside
shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct
system function. Proper grounding of the electrical outlet can be verified by a
certified electrician.
16
MT 2511, 2512, 2513, and 2514
Laser compliance statement
Laser compliance statement
Some models of ThinkPad computer are equipped from the factory with an optical
storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are
also sold separately as options. If one of these drives is installed, it is certified in
the U.S. to conform to the requirements of the Department of Health and Human
Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1
laser products. Elsewhere, the drive is certified to conform to the requirements of
the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825
for Class 1 laser products.
If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note
the following:
CAUTION:
Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles aqui
especificados pode resultar em perigosa exposição à radiação.
Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de réglage
et d’utilisation des commandes, ainsi que les procédures décrites.
Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann
gefährliche Laserstrahlung auftreten.
L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da quelle
specificate possono provocare l’esposizione a.
El uso de controles o ajustes o la ejecución de procedimientos distintos de los aquí
especificados puede provocar la exposición a radiaciones peligrosas.
Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage
device could result in exposure to hazardous laser radiation. There are no
serviceable parts inside those drives. Do not open.
Introduction
17
Laser compliance statement
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may
contain an embedded Class 3A or Class 3B laser diode. Note the following:
DANGER
Emits visible and invisible laser radiation when open. Do not stare into the beam, do
not view directly with optical instruments, and avoid direct exposure to the beam.
Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente
por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder
directement avec des instruments optiques, ou de vous exposer au rayon.
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische Instrumente in
den Laserstrahl sehen und den Strahlungsbereich meiden.
Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai eszközökkel.
Kerülje a sugárnyalábbal való érintkezést !
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo
direttamente con strumenti ottici e evitare l’esposizione diretta al fascio.
Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el haz
de luz. Evite la exposición directa al haz.
18
MT 2511, 2512, 2513, and 2514
General descriptions
The descriptions in this chapter apply to any ThinkPad model that has the
PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to
your particular computer.
Read this first
Before you go to the checkout guide, be sure to read this section.
Important notes
v Only certified trained personnel should service the computer.
v Before replacing any FRU, read the entire page on removing and
replacing FRUs.
v When you replace FRUs, use new nylon-coated screws.
v Be extremely careful during such write operations as copying, saving, or
formatting. Drives in the computer that you are servicing sequence might
have been altered. If you select an incorrect drive, data or programs might
be overwritten.
v Replace a FRU only with another FRU of the correct model. When you
replace a FRU, make sure that the model of the machine and the FRU part
number are correct by referring to the FRU parts list.
v A FRU should not be replaced because of a single, unreproducible
failure. Single failures can occur for a variety of reasons that have nothing
to do with a hardware defect, such as cosmic radiation, electrostatic
discharge, or software errors. Consider replacing a FRU only when a
problem recurs. If you suspect that a FRU is defective, clear the error log
and run the test again. If the error does not recur, do not replace the FRU.
v Be careful not to replace a nondefective FRU.
What to do first
When you do return a FRU, you must include the following information in the
parts exchange form or parts return form that you attach to it:
__ 1. Name and phone number of servicer
__ 2. Date of service
__ 3. Date on which the machine failed
__ 4. Date of purchase
__ 5. Failure symptoms, error codes appearing on the display, and beep
symptoms
__ 6. Procedure index and page number in which the failing FRU was detected
__ 7. Failing FRU name and part number
__ 8. Machine type, model number, and serial number
__ 9. Customer’s name and address
Note for warranty:
During the warranty period, the customer may be responsible for repair costs if the
computer damage was caused by misuse, accident, modification, unsuitable
physical or operating environment, or improper maintenance by the customer.
© Copyright Lenovo 2006, 2007
19
Read this first
Following is a list of some common items that are not covered under warranty and
some symptoms that might indicate that the system was subjected to stress beyond
normal use.
Before checking problems with the computer, determine whether the damage is
covered under the warranty by referring to the following list:
The following are not covered under warranty:
v LCD panel cracked from the application of excessive force or from being
dropped
v Scratched (cosmetic) parts
v Distortion, deformation, or discoloration of the cosmetic parts
v Plastic parts, latches, pins, or connectors that have been cracked or broken by
excessive force
v Damage caused by liquid spilled into the system
v Damage caused by the improper insertion of a PC Card or the installation of an
incompatible card
v Improper disc insertion or use of an optical drive
v Diskette drive damage caused by pressure on the diskette drive cover, foreign
material in the drive, or the insertion of a diskette with multiple labels
v Damaged or bent diskette eject button
v Fuses blown by attachment of a nonsupported device
v Forgotten computer password (making the computer unusable)
v Sticky keys caused by spilling a liquid onto the keyboard
v Use of an incorrect ac adapter on laptop products
The following symptoms might indicate damage caused by nonwarranted
activities:
v Missing parts might be a symptom of unauthorized service or modification.
v If the spindle of a hard disk drive becomes noisy, it may have been subjected to
excessive force, or dropped.
20
MT 2511, 2512, 2513, and 2514
Related service information
Related service information
This section provides information about the following:
v “Service Web site”
v “Restoring the pre-installed system”
v “Passwords”
v “Power management” on page 24
Service Web site
When the latest maintenance diskette and the system program service diskette
become available, they will be posted on http://www.lenovo.com/spm
Restoring the pre-installed system
When the hard disk drive is replaced because of a failure, no Product Recovery
program is on the new hard disk. In this case, you must use the recovery CD for
the computer. Order the recovery CD and the hard disk drive at the same time so
that you can recover the new hard disk drive with the pre-installed software when
they arrive. For information on which CD to order, see “Recovery CDs” on page
129.
Recovery to Factory Contents by using Product Recovery CDs
To create the service partition and install the factory contents from the recovery
CD, do the following:
Note
The recovery process might take up to 2 hours.
1. Insert the recovery CD into the CD or DVD drive, then restart the computer.
2. Following message is displayed: “Your computer originally included a Product
Recovery program ... Reinstall the Product Recovery program? (Y/N) [ ]”.
3. Press Y key. The service partition is created and loaded with the Product
Recovery program files.
4. At next window, press Enter to continue.
v The service partition is created. The system automatically reboots during this
process.
v The recovery process copies some files to the service partition, and
PKUNZIPs others.
v Follow the prompts. You may be prompted to change CDs.
v When the process is complete, the system reboots.
5. If you get a message asking which operating system to install, select the proper
operating system and press Enter.
6. A message is displayed: “Full Recovery:”. Press Enter to select.
7. On each of the next three windows, press the Y key.
8. Follow the prompts to complete the recovery.
Passwords
As many as three passwords may be needed for any ThinkPad computer: the
power-on password (POP), the hard-disk password (HDP), and the supervisor
password (SVP).
General descriptions
21
Related service information
If any of these passwords has been set, a prompt for it appears on the screen
whenever the computer is turned on. The computer does not start until the
password is entered.
Exception: If only an SVP is installed, the password prompt does not appear when
the operating system is booted.
Power-on password:
A power-on password (POP) protects the system from being powered on by an
unauthorized person. The password must be entered before an operating system
can be booted.
Hard-disk password:
There are two hard-disk passwords (HDPs):
v User HDP—for the user
v Master HDP—for the system administrator, who can use it to get access to the
hard disk even if the user has changed the user HDP
Note: There are two modes for the HDP: User only and Master + User. The
Master + User mode requires two HDPs; the system administrator enters
both in the same operation. The system administrator then provides the user
HDP to the system user.
Attention: If the user HDP has been forgotten, check whether a master HDP has
been set. If it has, it can be used for access to the hard disk drive. If no master
HDP is available, Lenovo does not provide any services to reset either the user or
the master HDP, or to recover data from the hard disk drive. The hard disk drive
can be replaced for a scheduled fee.
Supervisor password:
A supervisor password (SVP) protects the system information stored in the BIOS
Setup Utility. The user must enter the SVP in order to get access to the BIOS Setup
Utility and change the system configuration.
Attention: If the SVP has been forgotten and cannot be made available to the
servicer, there is no service procedure to reset the password. The system board
must be replaced for a scheduled fee.
How to remove the power-on password
To remove a POP that you have forgotten, do the following:
(A) If no SVP has been set:
1. Turn off the computer.
2. Remove the battery pack.
For how to remove the battery pack, see “1010 Battery pack” on page 56.
3. Remove the backup battery.
For how to remove the backup battery, see “1100 Backup battery” on page 71.
4. Turn on the computer and wait until the POST ends.
After the POST ends, the password prompt does not appear. The POP has been
removed.
5. Reinstall the backup battery and the battery pack.
(B) If an SVP has been set and is known by the servicer:
22
MT 2511, 2512, 2513, and 2514
Related service information
1. Turn on the computer; then, while the “To interrupt normal startup, press the
blue ThinkVantage button” message is displayed at the lower-left of the screen,
press the ThinkVantage button. Rescue and Recovery screen opens.
Note: To check whether the ThinkPad computer supports the Passphrase
function, enter BIOS Setup Utility and go to Security --> Password. If
Using Passphrase item is displayed in the menu, this function is
available on the ThinkPad computer.
2. Click Access BIOS. The system Restart Required window is displayed.
3. Click Yes. The computer restarts, and the BIOS Setup Utility screen opens.
4. Select Security, using the cursor directional keys to move down the menu.
5. Select Password.
6. Select Power-On Password.
7. Type the current SVP in the Enter Current Password field. then leave the Enter
New Password field blank, and press Enter twice.
8. In the Changes have been saved window, press Enter.
9. Press F10; then, in the Setup confirmation window, select Yes .
How to remove the hard-disk password
Attention: If User only mode is selected and the user HDP has been forgotten
and cannot be made available to the servicer, Lenovo does not provide any
services to reset the user HDPs or to recover data from the hard disk drive. The
hard disk drive can be replaced for a scheduled fee.
To remove a user HDP that has been forgotten, when the SVP and the master HDP
are known, do the following:
1. Turn on the computer; then, while the “To interrupt normal startup, press the
blue ThinkVantage button” message is displayed at the lower-left of the
screen, press the ThinkVantage button. The Rescue and Recovery screen
opens.
For models supporting the Passphrase function, press F1 while HDP icon is
appearing on the screen; then enter the master HDP. For the other models,
enter the master HDP.
Note: To check whether the ThinkPad computer supports the Passphrase
function, enter BIOS Setup Utility and go to Security --> Password. If
Using Passphrase item is displayed in the menu, this function is
available on the ThinkPad computer.
2. Click Access BIOS. The system Restart Required window is displayed.
Click Yes. The computer restarts, and the BIOS Setup Utility screen opens.
Select Security, using the cursor directional keys to move down the menu.
Select Password.
Select Hard-disk x password, where x is the letter of the hard disk drive. A
pop-up window opens.
7. Select Master HDP.
8. Type the current master HDP in the Enter Current Password field. then leave
the Enter New Password field blank, and press Enter twice.
9. Press F10.
3.
4.
5.
6.
10. Select Yes in the Setup Configuration window.
Both user HDP and master HDP will have been removed.
General descriptions
23
Related service information
Power management
To reduce power consumption, the computer has three power management modes:
screen blank, standby, and hibernation.
Screen blank mode
Screen blank mode has three variants, as follows:
1. If you press Fn+F3, or if the time set on the “LCD off timer” in the BIOS Setup
Utility expires,
v The LCD backlight turns off.
v The hard disk drive motor stops.
v The speaker is muted.
2. If you are using the Advanced Configuration and Power Interface (ACPI)
operating system and you press Fn+F3,
v The LCD backlight turns off.
v The hard disk drive motor stops.
3. If the time set on the “Turn off monitor” timer in the operating system expires,
v The LCD backlight turns off.
To end screen blank mode and resume normal operation, press any key.
Standby mode
When the computer enters standby mode, the following events occur in addition to
what occurs in screen blank mode:
v The LCD is powered off.
v The hard disk drive is powered off.
v The CPU stops.
To enter standby mode, press Fn+F4.
Note: If you are using the ACPI operating system, you can change the action of
Fn+F4.
In certain circumstances, the computer goes into standby mode automatically:
v If a “suspend time” has been set on the timer, and the user does not do any
®
operation with the keyboard, the TrackPoint , the hard disk, the parallel
connector, or the diskette drive within that time.
v If the battery indicator blinks orange, indicating that the battery power is low.
(Alternatively, if Hibernate when battery becomes low has been selected in the
“Power Management Properties” window, the computer goes into hibernation
mode.)
To cause the computer to return from standby mode and resume operation, do one
of the following:
v Press the Fn key.
v Open the LCD cover.
v Turn on the power switch.
Also, in either of the following events, the computer automatically returns from
standby mode and resumes operation:
v The ring indicator (RI) is signaled by a serial device or a PC Card device.
v The time set on the resume timer elapses.
24
MT 2511, 2512, 2513, and 2514
Related service information
Note: The computer does not accept any input immediately after it enters
standby mode. Wait a few seconds before taking any action to reenter
operation mode.
Hibernation mode
In hibernation mode, the following occurs:
v The system status, RAM, VRAM, and setup data are stored on the hard disk.
v The system is powered off.
Note: If the computer enters the hibernation mode while it is docked to the
docking station, do not undock it before resuming normal operation. If you
do undock it and then try to resume normal operation, you will get an error
message, and you will have to restart the system.
To cause the computer to enter hibernation mode, do any of the following:
v Press the Fn+F12 keys.
v If you are using the ACPI operating system and have defined one of the
following actions as the event that causes the system to go into hibernation
mode, perform that action.
– Closing the lid.
– Pressing the power button.
– Pressing Fn+F4 keys.
Also, the computer goes into hibernation mode automatically in either of the
following conditions:
v If a “hibernation time” has been set on the timer, and if the user does not do
any operation with the keyboard, the TrackPoint, the hard disk drive, the
parallel connector, or the diskette drive within that time.
v If the timer conditions are satisfied in suspend mode.
When the power is turned on, the computer returns from hibernation mode and
resumes operation. The hibernation file in the boot record on the hard disk drive is
read, and system status is restored from the hard disk drive.
General descriptions
25
Checkout guide
Checkout guide
Use the following procedures as a guide in identifying and correcting problems
with the ThinkPad computer.
Note: The diagnostic tests are intended to test only ThinkPad products. The use of
non-ThinkPad products, prototype cards, or modified options can lead to
false indications of errors and invalid system responses.
1. Identify the failing symptoms in as much detail as possible.
2. Verify the symptoms. Try to re-create the failure by running the diagnostic test
or by repeating the operation.
Testing the computer
The ThinkPad computer has a test program called PC-Doctor® DOS (hereafter
called PC-Doctor.) You can detect errors by running the diagnostics test included in
PC-Doctor. This section is an overview of the procedure. For details that depend
on model-unique functions, refer to “Product overview” on page 34.
For some possible configurations of the computer, PC-Doctor might not run
correctly. To avoid this problem, you need to initialize the computer setup by use
of the BIOS Setup Utility before you run PC-Doctor. On the BIOS Setup Utility
screen, press F9, Enter, F10, and then Enter.
Note: When you initialize the computer configuration, some devices are disabled,
such as the serial port. If you test one of these devices, you will need to
enable it by using PS2.EXE.
PC-Doctor cannot be used to test a device that is in the docking station, even if the
computer supports the docking station. To test a USB device, connect it to the USB
connector of the computer.
Creating the PC-Doctor diagnostics diskette
To create the PC-Doctor disk from the ThinkVantage Predesktop Area, do as
follows:
1. Enter the Predesktop application by pressing the ThinkVantage button during
POST.
2. When the Access application finishes loading, double-click the “Create
Diagnostic Diskettes” icon.
3. Authenticating the digital signature takes about 15 seconds; then the ThinkPad
computer will reboot into PC-DOS.
4. A batch file automatically starts up to prompt you through the process of
creating diskettes. You are notified of how many diskettes you will need.
a. You are prompted to insert each diskette in sequence.
b. Typically, all you need to do is to press the Enter key for the floppy drive;
the system then formats and creates the diskette.
c. Each diskette is erased and formatted with the PC-Doctor for DOS boot
image.
5. Once all the diskettes have been created, the ThinkPad computer will reboot.
The user is asked to remove all diskettes from the drive, or to insert the first
diskette created if it is desired to run the diagnostics.
To run the test, do as follows:
26
MT 2511, 2512, 2513, and 2514
Checkout guide
Note: In the following procedure, you can select an item not only with the arrow
keys, but also with the TrackPoint pointer. Instead of pressing Enter, click
the left button.
1. Insert the PC-Doctor disk into the diskette drive; then power on the computer.
If the computer cannot be powered on, go to “Power system checkout” on page
30, and check the power sources.
If an error code appears, go to “Symptom-to-FRU index” on page 44.
On the first screen, select the model and press Enter. Follow the instructions on
the screen.
2. The main panel of PC-Doctor appears.
3. Select Diagnostics with the arrow keys, and press Enter.
A pull-down menu appears. (Its exact form depends on the model.)
Note: PC-Doctor menu does not mean the formal support device list. Some
unsupported device names may appear in the PC-Doctor menu.
General descriptions
27
Checkout guide
Diagnostics
Interactive Tests
Hardware Info
Utility
Quit
F1=Help
Run Normal Test
Run Quick Test
CPU/Coprocessor
Systemboard
Video Adapter
Serial Ports
Parallel Ports
Fixed Disks
Diskette Drives
Other Devices
Communication
Wireless LAN
Memory Test - Full
Memory Test - Quick
PC-DOCTOR 2.0 Copyright 2002 PC-Doctor, Inc. All Rights Reserved.
Use the cursor keys and ESC to move in menus. Press ENTER to select.
The options on the test menu are as follows:
Diagnostics
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
Run Normal Test
Run Quick Test
CPU/Coprocessor
Systemboard
Video Adapter
Serial Ports
Parallel Ports
Fixed Disks
Diskette Drives
Other Devices
ThinkPad Devices
Communication
Wireless LAN
Memory Test – Full
Memory Test – Quick
Interactive Tests
v
v
v
v
v
v
v
v
Keyboard
Video
Internal Speaker
Mouse
Diskette
System Load
CD-ROM/DVD Test
Intel Wireless Radio
Notes:
v In the Keyboard test in Interactive Tests, the Fn key should be held down for
at least 2 seconds; otherwise, it cannot be sensed.
v Video Adapter test supports only the LCD display on the ThinkPad computer.
If you have an external monitor attached to your computer, detach it before
running PC-Doctor for DOS.
v To test Serial Ports or Parallel Ports, the ThinkPad computer must be attached
to the ThinkPad Advanced Dock or ThinkPad Advanced Mini Dock.
4. Run the applicable function test.
5. Follow the instructions on the screen. If there is a problem, PC-Doctor shows
messages describing it.
6. To exit the test, select Quit — Exit Diag.
To cancel the test, press Esc.
Note: After running PC-Doctor, check the time and date on the system and reset
them if they are incorrect.
28
MT 2511, 2512, 2513, and 2514
Checkout guide
Detecting system information with PC-Doctor
PC-Doctor can detect the following system information:
Hardware Info
v
v
v
v
v
v
v
v
v
v
v
System Configuration
Memory Contents
Physical Disk Drives
Logical Disk Drives
VGA Information
IDE Drive Info
PCI Information
PNPISA Info
SMBIOS Info
VESA LCD Info
Hardware Events Log
Utility
v
v
v
v
v
v
v
v
v
v
v
Run External Tests
Surface Scan Hard Disk
Benchmark System
DOS Shell
Tech Support Form
Battery Rundown
View Test Log
Print Log
Save Log
Full Erase Hard Drive
Quick Erase Hard Drive
PC-Doctor for Windows
This product is designed to help you troubleshoot and resolve problems related to
your computer. Select one of the categories listed below to display symptoms and
solutions:
v CHECK SYSTEM HEALTH
v SYSTEM AND DEVICE TESTS
v LENOVO TROUBLESHOOTING
v CENTER
v SYSTEM REPORTS
v UPDATES AND SUPPORT
General descriptions
29
Checkout guide
Power system checkout
To
1.
2.
3.
4.
5.
6.
7.
verify a symptom, do the following:
Turn off the computer.
Remove the battery pack.
Connect the ac adapter.
Check that power is supplied when you turn on the computer.
Turn off the computer.
Disconnect the ac adapter and install the charged battery pack.
Check that the battery pack supplies power when you turn on the computer.
If you suspect a power problem, see the appropriate one of the following power
supply checkouts:
v “Checking the ac adapter”
v “Checking operational charging”
v “Checking the battery pack” on page 31
v “Checking the backup battery” on page 31
Checking the ac adapter
You are here because the computer fails only when the ac adapter is used.
v If the power problem occurs only when the port replicator is used, replace the
port replicator.
v If the power-on indicator does not turn on, check the power cord of the ac
adapter for correct continuity and installation.
v If the computer does not charge during operation, go to ″Checking operational
charging.″
To check the ac adapter, do the following:
1. Unplug the ac adapter cable from the computer.
2. Measure the output voltage at the plug of the ac adapter cable. See the
following figure:
3
2
1
Pin
Voltage (V dc)
1
+20
2
0
3
Ground
(20V)
Note: Output voltage of pin no.2 of the ac adapter may different from the one
you are servicing.
3. If the voltage is not correct, replace the ac adapter.
4. If the voltage is acceptable, do the following:
v Replace the system board.
v If the problem persists, go to “Product overview” on page 34.
Note: Noise from the ac adapter does not always indicate a defect.
Checking operational charging
To check whether the battery charges properly during operation, use a discharged
battery pack or a battery pack that has less than 50% of the total power remaining
when installed in the computer.
30
MT 2511, 2512, 2513, and 2514
Checkout guide
Perform operational charging. If the battery status indicator or icon does not turn
on, remove the battery pack and let it return to room temperature. Reinstall the
battery pack. If the charge indicator or icon still does not turn on, replace the
battery pack.
If the charge indicator still does not turn on, replace the system board. Then
reinstall the battery pack. If it is still not charged, go to the next section.
Checking the battery pack
Battery charging does not start until the Power Meter shows that less than 95% of
the total power remains; under this condition the battery pack can charge to 100%
of its capacity. This protects the battery pack from being overcharged or from
having a shortened life.
To check your battery, move your cursor to the Power Meter icon in the icon tray
of the Windows taskbar and wait for a moment (but do not click), and the
percentage of battery power remaining is displayed. To get detailed information
about the battery, double-click the Power Meter icon.
Note: If the battery pack becomes hot, it may not be able to charge. Remove it
from the computer and leave it at room temperature for a while. After it
cools down, reinstall and recharge it.
To check the battery pack, do the following:
1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1
(+) and 5 (−). See the following figure:
7(+) 6(+)
5
4
3
1(-)
2(-)
Terminal
Voltage (V dc)
1
+ 0 to + 12.6
5
Ground (−)
3. If the voltage is less than +11.0 V dc, the battery pack has been discharged.
Note: Recharging will take at least 3 hours, even if the indicator does not turn
on.
If the voltage is still less than +11.0 V dc after recharging, replace the battery.
4. If the voltage is more than +11.0 V dc, measure the resistance between battery
terminals 4 and 5. The resistance must be 4 to 30 K .
If the resistance is not correct, replace the battery pack. If the resistance is
correct, replace the system board.
Checking the backup battery
Do the following:
1. Power off the computer, and unplug the ac adapter from it.
2. Turn the computer upside down.
3. Remove the battery pack (see “1010 Battery pack” on page 56).
4. Remove the backup battery (see “1100 Backup battery” on page 71).
5. Measure the voltage of the backup battery. See the following figure.
General descriptions
31
Checkout guide
Red (+)
Black (-)
Wire
Voltage (V dc)
Red
+2.5 to +3.2
Black
Ground
v If the voltage is correct, replace the system board.
v If the voltage is not correct, replace the backup battery.
v If the backup battery discharges quickly after replacement, replace the system
board.
32
MT 2511, 2512, 2513, and 2514
ThinkPad Z60t
Product overview . . . . . . . . . . . .
Specifications . . . . . . . . . . . . .
Status indicators . . . . . . . . . . . .
FRU tests . . . . . . . . . . . . . .
Fn key combinations . . . . . . . . . .
Symptom-to-FRU index . . . . . . . . . .
Numeric error codes . . . . . . . . . .
Error messages . . . . . . . . . . . .
Beep symptoms . . . . . . . . . . . .
No-beep symptoms . . . . . . . . . . .
LCD-related symptoms . . . . . . . . .
Intermittent problems . . . . . . . . . .
Undetermined problems . . . . . . . . .
FRU replacement notices . . . . . . . . . .
Screw notices . . . . . . . . . . . . .
Retaining serial numbers . . . . . . . . .
Restoring the serial number of the system unit
Retaining the UUID . . . . . . . . .
Reading or writing the ECA information . .
Removing and replacing a FRU . . . . . . . .
1010 Battery pack . . . . . . . . . . .
1020 Ultrabay Slim device . . . . . . . .
1030 Hard disk drive cover, hard disk drive, and
hard disk drive rubber rails . . . . . . . .
1040 Palm rest or palm rest with fingerprint
reader . . . . . . . . . . . . . . .
1050 DIMM . . . . . . . . . . . . .
1060 Keyboard . . . . . . . . . . . .
1070 Modem daughter card (MDC-1.5) . . . .
1080 PCI Express Mini card for wireless WAN . .
1090 PCI Express Mini card for wireless LAN . .
1100 Backup battery . . . . . . . . . .
1110 Keyboard bezel . . . . . . . . . .
1120 Speaker assembly . . . . . . . . .
© Copyright Lenovo 2006, 2007
34
34
36
39
41
44
44
48
49
49
50
51
51
52
52
52
53
53
53
55
56
57
58
60
62
63
65
67
69
71
72
74
1130 Fan assembly . . . . . . . . . . . 76
1140 CPU . . . . . . . . . . . . . . 78
1150 Wireless WAN antenna (DIV) . . . . . . 79
1160 LCD assembly . . . . . . . . . . . 80
1170 Base cover . . . . . . . . . . . . 83
1180 USB/S-video sub card with cable . . . . 86
1190 MG (Magnesium) frame . . . . . . . 87
1200 System board and PC Card slot assembly
92
2010 LCD front bezel . . . . . . . . . . 97
2020 Inverter card . . . . . . . . . . . 99
2030 Bluetooth daughter card (BDC-2) . . . . 100
2040 Wireless WAN antenna cable (MAIN) . . 102
2050 LCD panel, LCD cable, and hinges . . . 105
2060 LCD rear cover and wireless LAN antenna
cables . . . . . . . . . . . . . . . 108
Locations . . . . . . . . . . . . . . . 114
Front view . . . . . . . . . . . . . 114
Rear view . . . . . . . . . . . . . 115
Bottom view . . . . . . . . . . . . . 116
Parts list . . . . . . . . . . . . . . . 117
Overall . . . . . . . . . . . . . . 118
LCD FRUs . . . . . . . . . . . . . 126
Keyboard . . . . . . . . . . . . . . 128
Recovery CDs . . . . . . . . . . . . 129
Windows XP Professional . . . . . . . 129
Windows XP Home Edition . . . . . . 130
Miscellaneous parts . . . . . . . . . . 131
AC adapters . . . . . . . . . . . . . 132
Common parts list. . . . . . . . . . . 132
Tools . . . . . . . . . . . . . . 132
Power cords (system) . . . . . . . . . 133
Notices . . . . . . . . . . . . . . . 134
Trademarks . . . . . . . . . . . . . . 135
33
Product overview
Product overview
This section presents the following product-unique information:
v “Specifications”
v “Status indicators” on page 36
v “FRU tests” on page 39
v “Fn key combinations” on page 41
Specifications
The following table lists the specifications of the ThinkPad Z60t:
Feature
Description
Processor
v
v
v
v
v
v
v
v
Intel
Intel
Intel
Intel
Intel
Intel
Intel
Intel
Bus architecture
v
v
v
v
v
533-MHz PSB
533-MHz DDR2 SDRAM (PC2-4200)
HUB link
PCI bus
LPC bus
Graphic memory chip
v Intel 915GM
Display
v 14.0-inch wide, 16M colors, WXGA (1280 × 768 resolution)
TFT color LCD
Standard memory
v
v
v
v
v
Optional memory
v 256-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1
v 512-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1
v 1-GB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1
(maximum of 2048 MB)
CMOS RAM
v 242 bytes
Hard disk drive
v
v
v
v
v
Celeron M processor 360 (1.4 GHz), 1-MB L2 cache
Celeron M processor 370 (1.5 GHz), 1-MB L2 cache
Celeron M processor 380 (1.6 GHz), 1-MB L2 cache
Pentium M processor 740 (1.73 GHz), 2-MB L2 cache
Pentium M processor 750 (1.86 GHz), 2-MB L2 cache
Pentium M processor 760 (2 GHz), 2-MB L2 cache
Pentium M processor 770 (2.13 GHz), 2-MB L2 cache
Pentium M processor 780 (2.26 GHz), 2-MB L2 cache
256-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1
512-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1
512-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 2
1-GB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 1
1-GB DDR2-533 SDRAM SO-DIMM (PC2-4200) card × 2
40.0 GB, 5400 rpm, 9.5 mm high, SATA interface
60.0 GB, 5400 rpm, 9.5 mm high, SATA interface
80.0 GB, 5400 rpm, 9.5 mm high, SATA interface
100 GB, 5400 rpm, 9.5 mm high, SATA interface
100 GB, 7200 rpm, 9.5 mm high, SATA interface
Supported hard disk drives depend on the model.
Ultrabay Slim device
(standard)
v DVD drive, 9.5 mm high
v DVD/CD-RW combo drive, 9.5 mm high
v DVD-RAM/RW drive, 9.5 mm high
Fingerprint reader
Some models
(continued)
34
MT 2511, 2512, 2513, and 2514
Product overview
Feature
Description
I/O port
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
Audio
v Built-in stereo speakers
v Software control volume
Infrared transfer
v IrDA 1.1
Ethernet (on the system
board)
v Gigabit Ethernet
PCI Express Mini card
v ThinkPad 11a/b/g Wireless LAN Mini PCI Express
Adapter
PC Card slot
v PC Card (Type-II)
Modem
v ThinkPad Modem (MDC-1.5, 56 kbps HDA)
Bluetooth wireless
v ThinkPad Bluetooth with Enhanced Data Rate (BDC-2)
Touch pad
v UltraNav
ThinkLight
Yes
Battery
v Li-ion battery (4 cells) 2.6 Ah
v Li-ion battery (7 cells) 2.6 Ah
AC adapter
v 90-watt type
Preinstalled operating
system
v Windows XP Professional
v Windows XP Home Edition
External-monitor connector
SD card slot
Stereo headphone jack
Microphone jack
Video-out connector (S-Video)
3 Universal Serial Bus (USB) connectors
IEEE 1394 connector
Infrared port
RJ11 telephone connector
RJ45 Ethernet connector
Ultrabay™ Slim
Docking connector
Integrated wireless LAN feature (on some models)
Integrated wireless WAN feature (on some models)
Integrated Bluetooth feature (on some models)
ThinkPad Z60t
35
Product overview
Status indicators
The system status indicators show the status of the computer, as follows:
1
2
3
4
5
6
7
8
9
10
11
10
36
MT 2511, 2512, 2513, and 2514
9
8
Product overview
Indicator
Meaning
1
Wireless status
Green:
The wireless feature (the IEEE 802.11 standard) is on, and the
radio link is ready for use.
Blinking green:
Data is being transmitted.
2
Bluetooth status
Note: Some models do not have this indicator.
Green:
Bluetooth wireless is operational. This indicator is on when
Bluetooth wireless is on and not in suspend mode.
R
3
Wireless WAN
status
Green:
The wireless feature (the IEEE 802.11 standard) is on, and the
radio link is ready for use.
Blinking green:
Data is being transmitted.
4
Num lock
Green:
The numeric keypad on the keyboard is enabled. To enable or
disable the keypad, press and hold the Shift key, and press
the NumLk (ScrLk) key.
5
Caps lock
Green:
Caps Lock mode is enabled. To enable or disable Caps Lock
mode, press the Caps Lock key.
6
Drive in use
Green:
Data is being read from or written to the hard disk drive, the
diskette drive, or the drive in the Ultrabay Slim device. When
this indicator is on, do not put the computer into standby
mode or turn off the computer.
Note: Do not move the system while the green drive-in-use light
is on. Sudden physical shock could cause drive errors.
7
Power on
Green:
The computer is on and ready to use. This indicator stays lit
whenever the computer is on and is not in standby mode.
(continued)
ThinkPad Z60t
37
Product overview
38
Indicator
Meaning
8
Battery status
Green:
The battery is charged between 80% to 100% of the capacity,
and being discharged between 20% to 80% of the capacity.
Blinking green:
The battery is charged between 20% to 80% of the capacity,
and being charged.
Orange:
The battery is charged between 5% and 20% of the capacity,
and being discharged.
Blinking orange (slow):
The battery is charged between 5% to 20% of the capacity,
and being charged.
Blinking orange (rapid):
The battery is charged between 0% to 5% of the capacity.
9
AC power
status
Green:
The computer is connected to the ac power supply.
10
Standby status
Green:
The computer is in standby mode.
Blinking green:
The computer is entering standby mode or hibernation
mode, or is resuming normal operation.
11
Ultrabay Slim
status
Green:
An Ultrabay Slim device is installed and in use.
Blinking green:
An Ultrabay Slim device is in the process of being detached.
Turn off:
An Ultrabay Slim device is ready to be attached or detached.
MT 2511, 2512, 2513, and 2514
Product overview
FRU tests
The following table shows the test for each FRU.
FRU
Applicable test
System board
1. Diagnostics --> CPU/Coprocessor
2. Diagnostics --> Systemboard
3. If the docking station or the port replicator is attached to the
ThinkPad computer, undock it. Place the computer on a
horizontal surface, and run Diagnostics --> ThinkPad Devices
--> HDD Active Protection Test.
Note: Do not apply any physical shock to the computer while
the test is running.
Power
Diagnostics --> ThinkPad Devices --> AC Adapter, Battery 1 (
Battery 2)
LCD unit
1. Diagnostics --> Video Adapter
2. Interactive Tests --> Video
Modem daughter card
(MDC-1.5)
1. Make sure the modem is set up correctly.
2. Replace the modem jack and the modem card in turn, and run
the following tests in Diagnostics --> Communication:
a. Conexant Smart Modem Interrupt
b. Conexant Smart Modem Dialtone
Audio
1. Interactive Tests --> Internal Speaker
2. Diagnostics --> Other Devices --> Analog Devices HDA
CODEC Test
Speaker
Interactive Tests --> Internal Speaker
PC Card slot
1. Diagnostics --> Systemboard --> PCMCIA
2. Insert a PC Card Wrap Plug into every PC Card slot, and run
Diagnostics --> Systemboard --> PCMCIA External Loop
Keyboard
1. Diagnostics --> Systemboard --> Keyboard
2. Interactive Tests --> Keyboard
Hard disk drive
Diagnostics --> Fixed Disks
Diskette drive
1. Diagnostics --> Diskette Drives
2. Interactive Tests --> Diskette
DVD drive or
DVD/CD-RW combo
drive
1. Diagnostics --> Other Devices --> CD-ROM/DVD
2. Interactive Tests --> CD-ROM/DVD Test
(continued)
ThinkPad Z60t
39
Product overview
FRU
Applicable test
Memory
1. If two DIMMs are installed, remove one of them and run
Diagnostics --> Memory Test—Quick.
2. If the problem does not recur, return the DIMM to its place,
remove the other one, and run the test again.
3. If the test does not detect the error, run Diagnostics -->
Memory Test—Full.
Fan
1. Turn on the computer and check the air turbulence at the
louver near the PC Card slot.
2. Run Diagnostics --> ThinkPad Devices --> Fan.
TrackPoint or pointing If the TrackPoint does not work, check the configuration as
device
specified in the ThinkPad Configuration program. If the
TrackPoint is disabled, select Automatic to enable it.
After you use the TrackPoint, the pointer may drift on the screen
for a short time. This drift can occur when a slight, steady
pressure is applied to the TrackPoint pointer. This symptom is not
a hardware problem. If the pointer stops after a short time, no
service action is necessary.
If enabling the TrackPoint does not correct the problem, continue
with the following:
v Interactive Tests --> Mouse
Touch Pad
40
MT 2511, 2512, 2513, and 2514
If the Touch Pad does not work, check the configuration as
specified in the ThinkPad Configuration program. If the Touch
Pad is disabled, select Automatic to enable it. If enabling the
Touch Pad does not correct the problem, continue with the
following:
v Interactive Tests --> Mouse
Product overview
Fn key combinations
The following table shows the function of each combination of Fn with a function
key.
Key combination
Description
Fn+F1
Reserved.
Fn+F2
Reserved.
Fn+F3
Select a power scheme that has been created by Power Manager.
Fn+F4
Put the computer in standby mode. To return to normal operation,
press the Fn key only, without pressing a function key.
Note: In Windows 2000 and Windows XP, this combination of
keys functions as a sleep button. The setting can be changed so
that pressing it puts the computer into hibernation mode or even
shuts the computer down.
Fn+F5
Enable or disable the built-in wireless networking features and the
Bluetooth features. If you press Fn+F5, a list of wireless features is
displayed in the Wireless Radio Control window. You can quickly
change the power state of each feature in the list.
Note: This function is supported only in Windows 2000 and
Windows XP.
Note: If you want to use this combination of keys to enable or
disable the feature, the following device drivers must be installed
on the computer beforehand:
v ThinkPad Power Management driver
v OnScreen Display utility
v Wireless device drivers
Fn+F6
Reserved.
Fn+F7
Switch a display output location
v External monitor (CRT display)
v Computer display and external monitor (LCD + CRT display)
v Computer display (LCD)
Note: For any operating system other than Windows 2000 or
Windows XP, no additional procedure is needed; just press Fn+F7.
Notes:
1. This function does not work when different desktop images
are displayed on the computer display and the external
monitor (the Extend desktop function).
2. This function does not work while a DVD movie or a video
clip is playing.
3. For Windows 2000 or Windows XP, a hotkey application might
take over the switching function.
(continued)
ThinkPad Z60t
41
Product overview
Key combination
Description
Fn+F8
Change the settings of the TrackPoint and the touch pad.
Fn+F9
Open the ThinkPad EasyEject Utility screen. Buttons for the
following choices are displayed:
v Eject ThinkPad PC from Dock: This button is displayed only if
the ThinkPad computer has been attached to a ThinkPad Dock
II or a ThinkPad Mini Dock. The computer can be detached
from the ThinkPad Dock II or the ThinkPad Mini Dock.
v Eject ThinkPad PC from Port Replicator: This button is
displayed only if the ThinkPad computer has been docked in a
ThinkPad Essential Port Replicator and one or more USB
devices have been connected to the ThinkPad Essential Port
Replicator. You can stop and remove all the USB devices safely
by clicking the button.
v Run EasyEject Actions: This button is used to select, stop, or
remove external devices connected to the ThinkPad computer.
v Configure EasyEject Actions: Opens the ThinkPad EasyEject
Utility main window.
v Fn+F9 Settings: Configures the settings for the Fn+F9 function.
You can use this utility to stop and remove all ejectable devices
connected to the ThinkPad computer, the ThinkPad Mini Dock, or
the ThinkPad Port Replicator II. You cannot use it to detach the
computer from the ThinkPad Mini Dock or the ThinkPad Port
Replicator II.
Note: This function is supported only in Windows 2000 and
Windows XP.
Fn+F10
Reserved.
Fn+F11
Reserved.
Fn+F12
Put the computer into hibernation mode. To return to normal
operation, press the power button for less than four seconds.
Note: To use Fn+F12 for hibernation in Windows 2000 or
Windows XP, you must have the PM device driver installed on the
computer.
(continued)
42
MT 2511, 2512, 2513, and 2514
Product overview
Key combination
Description
Fn+PgUp
Turn the ThinkLight on or off.
Note: This function is supported only on the ThinkPad computers
that have the ThinkLight. The on or off status of the ThinkLight is
shown on the screen for a few seconds when you press Fn+PgUp.
Fn+Home
The computer display becomes brighter.
Fn+End
The computer display becomes dimmer.
Fn+Spacebar
Enable the FullScreen Magnifier function.
Fn+PrtSc
Has the same function as the SysRq key.
Fn+ScrLk
Enable or disable the numeric keypad.
Fn+Pause
Has the same function as the Break key.
Fn+cursor keys
These key combinations work with Windows Media Player.
Fn+down arrow key works for the Play or Pause button, Fn+up
arrow key for the Stop button, Fn+right arrow key for the Next
Track button, and Fn+left arrow key for the Previous Track button.
ThinkPad Z60t
43
Symptom-to-FRU index
Symptom-to-FRU index
The symptom-to-FRU index in this section lists symptoms and errors and their
possible causes. The most likely cause is listed first, in boldface type.
Note: Do the FRU replacement or other actions in the sequence shown in the
column headed “FRU or action, in sequence.” If replacing a FRU does not
solve the problem, put the original part back in the computer. Do not
replace a nondefective FRU.
This index can also help you determine, during regular servicing, what FRUs are
likely to need to be replaced next.
A numeric error is displayed for each error detected in POST or system operation.
In the displays, n can be any number.
If no numeric code is displayed, check the narrative descriptions of symptoms. If
the symptom is not described there, go to “Intermittent problems” on page 51.
Note
For a device not supported by diagnostic codes in the ThinkPad notebook
computers, see the manual for that device.
Numeric error codes
Symptom or error
FRU or action, in sequence
0175
Bad CRC1, stop POST task—The EEPROM
checksum is not correct.
System board.
0176
System Security—The system has been
tampered with.
1. Run BIOS Setup Utility, and save the
current setting by pressing F10.
2. System board.
0177
Bad SVP data, stop POST task—The
checksum of the supervisor password in the
EEPROM is not correct.
System board.
0182
1. Run BIOS Setup Utility. Press F9, and
Bad CRC2. Enter BIOS Setup and load Setup
Enter to load the default setting. Then
defaults.—The checksum of the CRS2 setting
save the current setting by pressing F10.
in the EEPROM is not correct.
2. System board.
0185
Bad startup sequence settings. Enter BIOS
Setup and load Setup defaults.
1. Run BIOS Setup Utility. Press F9, and
Enter to load the default setting. Then
save the current setting by pressing F10.
0187
EAIA data access error—The access to
EEPROM is failed.
System board.
0188
Invalid RFID Serialization Information Area.
System board.
0189
System board.
Invalid RFID configuration information
area—The EEPROM checksum is not correct.
44
MT 2511, 2512, 2513, and 2514
Symptom-to-FRU index
Symptom or error
FRU or action, in sequence
0190
Critical low-battery error
1. Charge the battery pack.
2. Battery pack.
0191
System Security—Invalid Remote Change
requested.
1. Run BIOS Setup Utility, and then save
current setting by pressing F10.
2. System board.
0192
System Security— Embedded Security
hardware tamper detected.
System board.
0199
System Security— Security password retry
count exceeded.
1. Run BIOS Setup Utility, and then save
the current setting by pressing F10.
2. System board.
01C8
Two or more modem devices are found.
Remove all but one of them. Press <Esc> to
continue.
1. Remove either a Mini-PCI Card or a
modem daughter card. Otherwise, press
Esc to ignore the warning message.
2. System board.
01C9
More than one Ethernet devices are found.
Remove one of them. Press <Esc> to
continue.
1. Remove the Ethernet device that you
installed; or press Esc to ignore the
warning message.
2. System board.
01CA
More than one Wireless LAN devices are
found. Remove one of them.
1. Remove the wireless LAN device that
you installed.
2. System board.
0200
Hard disk error—The hard disk is not
working.
1. Reseat the hard disk drive.
2. Load Setup Defaults in BIOS Setup
Utility.
3. Hard disk drive.
4. System board.
021x
Keyboard error.
Run interactive tests of the keyboard and
the auxiliary input device.
0220
Monitor type error—Monitor type does not
match the one specified in CMOS.
Load Setup Defaults in BIOS Setup Utility.
0230
Shadow RAM error—Shadow RAM fails at
offset nnnn.
System board.
0231
System RAM error—System RAM fails at
offset nnnn.
1. DIMM.
2. System board.
0232
Extended RAM error— Extended RAM fails
at offset nnnn.
1. DIMM.
2. System board.
0250
System battery error—System battery is
dead.
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
0251
System CMOS checksum bad— Default
configuration used.
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
ThinkPad Z60t
45
Symptom-to-FRU index
46
Symptom or error
FRU or action, in sequence
0252
Password checksum bad—The password is
cleared.
Reset the password by running BIOS Setup
Utility.
0260
System timer error.
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
3. System board.
0270
Real-time clock error.
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
3. System board.
0271
Date and time error—Neither the date nor
the time is set in the computer.
Run BIOS Setup Utility to reset the time
and date.
0280
Previous boot incomplete— Default
configuration used.
1. Load “Setup Default” in BIOS Setup
Utility.
2. DIMM.
3. System board.
02F4
EISA CMOS not writable.
1. Load Setup Defaults in BIOS Setup
Utility.
2. Replace the backup battery.
3. System board.
02F5
DMA test failed.
1. DIMM.
2. System board.
02F6
Software NMI failed
1. DIMM.
2. System board.
02F7
Fail-safe timer NMI failed
1. DIMM.
2. System board.
1802
Unauthorized network card is plugged
in—Turn off and remove the miniPCI
network card.
1. Remove Mini PCI network card.
2. System board.
1803
Unauthorized daughter card is plugged
in—Turn off and remove the daughter card.
1. Remove the daughter card that you
installed.
2. System board.
1804
Unauthorized WAN card is plugged
in—Power off and remove the WAN card.
1. Remove the WAN card that you
installed.
2. System board.
1820
More than one external fingerprint reader is
attached. Power off and remove all but the
reader that you set up within your main
operating system.
Remove all but the reader that you set up
for the authentication.
MT 2511, 2512, 2513, and 2514
Symptom-to-FRU index
Symptom or error
FRU or action, in sequence
2000
Hard Drive Active Protection sensor
diagnostics failed.
Press <Esc> to continue.
Press <F1> to enter SETUP
1. Undock docking station or port
replicator if it is attached to the
ThinkPad computer, and place the
computer on a horizontal surface. Do not
apply any physical shock to the
computer.
2. Run Diagnostics --> ThinkPad Devices
--> HDD Active Protection Test.
2010
Warning: Your internal hard disk drive
(HDD) may not function correctly on this
system. Ensure that your HDD is supported
on this system and that the latest HDD
firmware is installed.
Inform the following information to the
customer:
If in the primary bay the customer is using a
non-IBM or non-Lenovo hard disk drive
(HDD), or an old generation IBM HDD
which is not supported by this system, with
the risk in mind, the customer can still use it
by pressing ESC. If in the primary drive bay
the customer is using a supported
IBM/Lenovo HDD with an old firmware,
the customer needs to update its firmware to
the latest. The latest version is available at
http://www.lenovo.com/support
2100
Initialization error on HDD0 (Main hard
disk drive)
1. Reseat the hard disk drive.
2. Main hard disk drive.
3. System board.
2102
Initialization error on HDD1 (Ultrabay hard
disk drive)
1. Reseat the hard disk drive.
2. Ultrabay hard disk drive.
3. System board.
2110
1. Reseat the hard disk drive.
Read error on HDD0 (Main hard disk drive) 2. Main hard disk drive.
3. System board.
2112
Read error on HDD1 (Ultrabay hard disk
drive)
1. Reseat the hard disk drive.
2. Ultrabay hard disk drive.
3. System board.
ThinkPad Z60t
47
Symptom-to-FRU index
Error messages
Symptom or error
FRU or action, in sequence
Device address conflict.
1. Load “Setup Defaults” in the BIOS
Setup Utility.
2. Backup battery.
3. System board.
Allocation error for device.
1. Load “Setup Defaults” in the BIOS
Setup Utility.
2. Backup battery.
3. System board.
Failing bits: nnnn.
1. DIMM.
2. System board.
Invalid system configuration data.
1. DIMM.
2. System board.
I/O device IRQ conflict.
1. Load “Setup Defaults” in the BIOS
Setup Utility.
2. Backup battery.
3. System board.
Hibernation error.
1. Restore the system configuration to
what it was before the computer
entered hibernation mode.
2. If memory size has been changed,
re-create the hibernation file.
Fan error.
1. Fan.
2. Thermal grease.
3. System board.
Thermal sensing error.
System board.
Cannot boot from any device.
Check the status of device which you want
to boot from.
Device not found.
1. The device you want to boot from.
2. System board.
Device Error.
1. The device you want to boot from.
2. System board.
No valid operating system.
1. Check that the operating system has no
failure and is installed correctly.
2. Reinstall the operation system.
Excluded from boot order.
v Enter the BIOS Setup Utility and add the
device in boot order.
48
MT 2511, 2512, 2513, and 2514
Symptom-to-FRU index
Beep symptoms
Symptom or error
FRU or action, in sequence
One beep and a blank, unreadable, or
flashing LCD.
1.
2.
3.
4.
One long and two short beeps, and a blank
or unreadable LCD.
1. System board.
2. LCD assembly.
3. DIMM.
Two short beeps with error codes.
POST error. See “Numeric error codes” on
page 44.
Two short beeps and a blank screen.
1. System board.
2. DIMM.
Three short beeps, pause, three more short
beeps, and one short beep.
1. DIMM.
2. System board
Reseat the LCD connector.
LCD assembly.
External CRT.
System board.
One short beep, pause, three short beeps,
pause, three more short beeps, and one short
beep.
Only the cursor appears.
Reinstall the operating system.
Four cycles of four short beeps and a blank
screen.
System board (security chip)
Five short beeps and a blank screen.
System board
No-beep symptoms
Symptom or error
FRU or action, in sequence
No beep, power-on indicator on, LCD blank, 1. Make sure that every connector is
and no POST.
connected tightly and correctly.
2. DIMM.
3. System board.
No beep, power-on indicator on, and LCD
blank during POST.
1. Reseat DIMM.
The power-on password prompt appears.
A power-on password or a supervisor
password is set. Type the password and
press Enter.
The hard-disk password prompt appears.
A hard-disk password is set. Type the
password and press Enter.
2. System board.
ThinkPad Z60t
49
Symptom-to-FRU index
LCD-related symptoms
Important: The TFT LCD for the notebook computer contains many thin-film
transistors (TFTs). The presence of a small number of dots that are
missing, discolored, or always lighted is characteristic of TFT LCD
technology, but excessive pixel problems can cause viewing concerns.
The LCD should be replaced if the number of missing, discolored, or
lighted dots in any background is as follows:
Minimum quantity of defective pixels required for LCD replacement on June 2006 or later
manufactured ThinkPad
LCD resolution
Bright dots
Dark dots
Bright and dark dots
XGA, WXGA
5
6
6
WXGA+, SXGA+,
WSXGA+
5
8
10
UXGA, WUXGA,
QXGA
5
13
13
Notes:
1. Lenovo will not provide replacement if the LCD is within specification as we
cannot guarantee that any replacement LCD will have zero pixel defects.
2. A bright dot means a pixel is always on (white or color.)
3. A dark dot means a pixel is always off (black color.)
4. One pixel consists of R, G, B sub-pixels.
Symptom or error
FRU or action, in sequence
No beep, power-on indicator on, and a
blank LCD during POST.
System board.
v
v
v
v
LCD
LCD
LCD
LCD
backlight not working.
too dark.
brightness cannot be adjusted.
contrast cannot be adjusted.
v
v
v
v
LCD screen unreadable.
Characters missing pixels.
Screen abnormal.
Wrong color displayed.
Horizontal or vertical lines displayed on
LCD.
50
MT 2511, 2512, 2513, and 2514
1. Reseat the LCD connectors.
2. LCD assembly.
3. System board.
1. See important note for “LCD-related
symptoms.”
2. Reseat all LCD connectors.
3. LCD assembly.
4. System board.
LCD assembly.
Symptom-to-FRU index
Intermittent problems
Intermittent system hang problems can be due to a variety of causes that have
nothing to do with a hardware defect, such as cosmic radiation, electrostatic
discharge, or software errors. FRU replacement should be considered only when a
problem recurs.
When analyzing an intermittent problem, do the following:
1. Run the diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRUs.
3. If any error is detected, replace the FRU shown by the FRU code. Rerun the
test to verify that no more errors exist.
Undetermined problems
If the diagnostic tests did not identify the adapter or device that has failed, if
wrong devices are installed, or if the system simply is not operating, follow these
procedures to isolate the failing FRU (do not isolate FRUs that have no defects).
Verify that all attached devices are supported by the computer.
Verify that the power supply being used at the time of the failure is operating
correctly. (See “Power system checkout” on page 30.)
1. Turn off the computer.
2. Visually check each FRU for damage. Replace any damaged FRU.
3. Remove or disconnect all of the following devices:
a. Non-ThinkPad devices
b. Devices attached to the port replicator
c. Printer, mouse, and other external devices
d. Battery pack
e. Hard disk drive
f. External diskette drive or optical drive
g. DIMM
h. Optical disk or diskette in the internal drive
i. PC Cards
4. Turn on the computer.
5. Determine whether the problem has been solved.
6. If the problem does not recur, reconnect the removed devices one at a time
until you find the failing FRU.
7. If the problem remains, replace the following FRUs one at a time (do not
replace a nondefective FRU):
a. System board
b. LCD assembly
ThinkPad Z60t
51
FRU replacement notices
FRU replacement notices
This section contains notices related to removing and replacing parts. Read this
section carefully before replacing any FRU.
Screw notices
Loose screws can cause a reliability problem. In the ThinkPad computer, this
problem is addressed with special nylon-coated screws that have the following
characteristics:
v They maintain tight connections.
v They do not easily come loose, even with shock or vibration.
v They are harder to tighten.
v Each one should be used only once.
Do the following when you service this machine:
v Keep the screw kit (for the P/N, see “Miscellaneous parts” on page 131) in your
tool bag.
v Always use new screws.
v Use a torque screwdriver if you have one.
Tighten screws as follows:
v Plastic to plastic
Turn an additional 90 degrees after the screw head touches the surface of the
plastic part:
90 degrees more
(Cross-section)
v Logic card to plastic
Turn an additional 180 degrees after the screw head touches the surface of the
logic card:
180 degrees more
(Cross-section)
v Torque driver
If you have a torque driver, refer to the “Torque” column for each step.
v Make sure that you use the correct screw. If you have a torque screwdriver,
tighten all screws firmly to the torque shown in the table. Never use a screw
that you removed. Use a new one. Make sure that all of the screws are
tightened firmly.
v Ensure torque screwdrivers are calibrated correctly following country
specifications.
Retaining serial numbers
This section includes the following descriptions:
v “Restoring the serial number of the system unit” on page 53
52
MT 2511, 2512, 2513, and 2514
FRU replacement notices
v “Retaining the UUID”
v “Reading or writing the ECA information”
Restoring the serial number of the system unit
When the computer was manufactured, the EEPROM on the system board was
loaded with the serial numbers of the system and all major components. These
numbers need to remain the same throughout the life of the computer.
If you replace the system board, you must restore the serial number of the system
unit to its original value.
Before replacing the system board, save the original serial number by doing the
following:
1. Install the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and
restart the computer.
2. From the main menu, select 1. Set System Identification.
3. Select 2. Read S/N data from EEPROM.
The serial number of each device in your computer is displayed; the serial number
of the system unit is listed as follows:
v 20: Serial number
Write down that number.
Note: The serial number of the system unit is also written on the label attached to
the bottom of the computer.
After you have replaced the system board, restore the serial number by doing the
following:
1. Install the ThinkPad Hardware Maintenance Diskette Version 1.73 or later and
restart the computer.
2. From the main menu, select 1. Set System Identification.
3. Select 1. Add S/N data from EEPROM.
Follow the instructions on the screen.
Retaining the UUID
The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to
your computer at production and stored in the EEPROM of your system board.
The algorithm that generates the number is designed to provide unique IDs until
the year A.D. 3400. No two computers in the world have the same number.
When you replace the system board, you must set the UUID on the new system
board as follows:
1. Install the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and
restart the computer.
2. From the main menu, select 4. Assign UUID.
A new UUID is created and written. If a valid UUID already exists, it is not
overwritten.
Reading or writing the ECA information
Information on Engineering Change Announcements (ECA) are stored in the
EEPROM of the system board. The electronic storage of this information simplifies
the procedure to check if the ECA has been previously applied to a machine. The
machine does not need to be disassembled to check for the ECA application.
ThinkPad Z60t
53
FRU replacement notices
To check what ECAs have been previously applied to the machine, use the ECA
Information Read/Write function on the ThinkPad Hardware Maintenance Diskette
Version 1.73 or later.
1. Insert the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and
restart the computer.
2. From the main menu, select 6. Set ECA Information.
3. To read ECA information, select 2. Read ECA/rework number from EEPROM
and follow the instruction.
4. To read box build date, select 5. Read box build date from EEPROM, and
follow the instruction on the screen.
After an ECA has been applied to the machine, the EEPROM must be updated to
reflect the ECA's application. Use the ThinkPad Hardware Maintenance Diskette
Version 1.73 or later to update the EEPROM.
Note: Only the ECA number is stored in the EEPROM. The machine type of the
ECA is assumed be the same as the machine type of the machine that had
the ECA applied to it.
1. Insert the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and
restart the computer.
2. From the main menu, select 6. Set ECA Information.
3. To write ECA information, select 1. Write ECA/rework number from EEPROM,
and follow the instruction.
4. To write box build date, select 4. Write box build date from EEPROM, and
follow the instruction on the screen.
If the system board is being replaced, try to read the ECA information from the old
system board and transfer the information to the new system. If the system board
is inoperable, this will not be possible.
54
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
Removing and replacing a FRU
This section presents directions and drawings for use in removing and replacing a
FRU. Be sure to observe the following general rules:
1. Do not try to service any computer unless you have been trained and certified.
An untrained person runs the risk of damaging parts.
2. Before replacing any FRU, review “FRU replacement notices” on page 52.
3. Begin by removing any FRUs that have to be removed before the failing FRU.
Any such FRUs are listed at the top of the page. Remove them in the order in
which they are listed.
4. Follow the correct sequence in the steps for removing the FRU, as given in the
drawings by the numbers in square callouts.
5. When turning a screw to replace a FRU, turn it in the direction as given by the
arrow in the drawing.
6. When removing the FRU, move it in the direction as given by the arrow in the
drawing.
7. To put the new FRU in place, reverse the removal procedure and follow any
notes that pertain to replacement. For information about connecting and
arranging internal cables, see “Locations” on page 114.
8. When replacing a FRU, use the correct screw as shown in the procedures.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any interconnecting
cables.
Attention: After replacing a FRU, do not turn on the computer until you have
made sure that all screws, springs, and other small parts are in place and none are
loose inside the computer. Verify this by shaking the computer gently and listening
for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.
Attention: The system board is sensitive to, and can be damaged by, electrostatic
discharge. Before touching it, establish personal grounding by touching a ground
point with one hand or by using an electrostatic discharge (ESD) strap (P/N
6405959).
ThinkPad Z60t
55
Removing and replacing a FRU
1010 Battery pack
DANGER
Use only the battery specified in the parts list for your computer. Any other battery
could ignite or explode.
Unlock the battery release lever 1. Holding the battery release lever in the
unlocked position 2, remove the battery pack in the direction shown by arrow
3.
1
2
3
When installing: Install the battery pack along the slide rails of the slot. Then
make sure that the battery release lever is locked, as in this
figure.
2
1
56
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
1020 Ultrabay Slim device
Note
Ultrabay Slim does not accept any of the following devices:
v Ultrabay Plus devices
v Ultrabay 2000 devices
Note: When you release the switch in step 1, the lever pops out. In step 2,
pull the lever a little to release the device from the bay.
1
2
3
ThinkPad Z60t
57
Removing and replacing a FRU
1030 Hard disk drive cover, hard disk drive, and hard disk
drive rubber rails
For access, remove this FRU:
v “1010 Battery pack” on page 56
Attention
v Do not drop the hard disk drive or apply any physical shock to it. The
hard disk drive is sensitive to physical shock. Improper handling can cause
damage and permanent loss of data.
v Before removing the drive, have the user make a backup copy of all the
information on it if possible.
v Never remove the drive while the system is operating or is in suspend
mode.
1
Step
Screw (quantity)
1
HDD screw (1) or security screw (1)
Note: Use a 2.5-mm Allen wrench to remove the security screw.
(continued)
58
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
3
2
4
5
When installing: Make sure that the hard disk drive connector is attached firmly.
(continued)
6
6
When installing: Rubber rails of the hard disk drive must be attached to the
replacement drive. Otherwise the hard disk drive cannot be
properly installed to the computer.
ThinkPad Z60t
59
Removing and replacing a FRU
1040 Palm rest or palm rest with fingerprint reader
For access, remove this FRU in order:
v “1010 Battery pack” on page 56
Note
In models with the fingerprint reader, the sensor has been attached to the
palm rest FRU as the child part. If the fingerprint reader has any defects and
needs to be replaced, you need to replace the palm rest by the procedures
given in this section. These procedures are the same for a palm rest with or
without a fingerprint reader.
1
1
1
1
Step
Icon
1
(continued)
60
MT 2511, 2512, 2513, and 2514
Screw (quantity)
Color
M2 × 14 mm, flat-head, nylon-coated Black
(4)
Torque
0.196 Nm
(2.0 kgfcm)
Removing and replacing a FRU
In step 2, press the left and right sides of the palm rest toward the center to
release the side latches, as in this figure. Then release the latches indicated by
arrow 3.
3
3
2
2
Pull the palm rest a little in the direction shown by arrow 4, and then detach the
touch pad connector by pulling the tab with your fingers in the direction shown by
arrow 5.
4
5
When installing: Make sure that the touch pad connector is attached firmly.
ThinkPad Z60t
61
Removing and replacing a FRU
1050 DIMM
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
1
2
1
When installing: Insert the notched end of the DIMM into the socket. Press the
DIMM firmly, and pivot it until it snaps into the place.
Make sure that it is fixed firmly in the slot and does not move
easily.
62
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
1060 Keyboard
For access, remove this FRU:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
1
Step
1
Icon
Screw (quantity)
Color
M2 × 14 mm, flat-head, nylon-coated Black
(1)
Torque
0.196 Nm
(2.0 kgfcm)
Lift the keyboard a little in the direction shown by arrow 2, and then detach the
connector 3.
2
3
ThinkPad Z60t
63
Removing and replacing a FRU
When installing: Make sure that the keyboard edges a are under the frame as
shown in this figure.
a
a
64
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
1070 Modem daughter card (MDC-1.5)
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
1
2
1
Step
Screw (quantity)
Color
Torque
1
M2 × 3 mm, flat-head, nylon-coated (2)
Black
0.196 Nm
(2.0 kgfcm)
In step 2, remove the card by pulling the tab with your fingers in the direction
shown by the arrow.
(continued)
ThinkPad Z60t
65
Removing and replacing a FRU
Turn the card over 3, and detach the modem connector 4.
3
4
When installing: Make sure that the modem connector and the connector on the
underside of the card are attached firmly.
66
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
1080 PCI Express Mini card for wireless WAN
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
In steps 1a and 1b, unplug the jacks by using the removal tool antenna RF
connector (P/N: 08K7159), or pick the connectors with your fingers and gently
unplug them in the direction shown by the arrow.
2
2
1a
1b
Step
Screw (quantity)
Color
Torque
2
M2 × 3 mm, flat-head, nylon-coated (2)
Black
0.196 Nm
(2.0 kgfcm)
(continued)
ThinkPad Z60t
67
Removing and replacing a FRU
3
When installing: Plug the red cable into the jack labeled MAIN on the card, and
the blue cable into the jack labeled DIV.
68
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
1090 PCI Express Mini card for wireless LAN
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
In steps 1a and 1b, unplug the jacks by using the removal tool antenna RF
connector (P/N: 08K7159), or pick the connectors with your fingers and gently
unplug them in the direction shown by arrow 2.
2
2
1b
1a
Step
Screw (quantity)
Color
Torque
2
M2 × 3 mm, flat-head, nylon-coated (2)
Black
0.196 Nm
(2.0 kgfcm)
(continued)
ThinkPad Z60t
69
Removing and replacing a FRU
3
When installing: Plug the gray cable into the jack labeled MAIN on the card, and
the black cable to the jack labeled AUX.
70
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
1100 Backup battery
DANGER
Use only the battery specified in the parts list for your computer. Any other battery
could ignite or explode.
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
2
1
When installing: Make sure that the battery connector is attached firmly.
ThinkPad Z60t
71
Removing and replacing a FRU
1110 Keyboard bezel
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1060 Keyboard” on page 63
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
1
1
Step
Screw (quantity)
Color
Torque
1
M2 × 14 mm, flat-head, nylon-coated (2)
Black
0.196 Nm
(2.0 kgfcm)
(continued)
72
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
3
2
2
2
2
Step
Screw (quantity)
Color
Torque
2
M2 × 3 mm, flat-head, nylon-coated (4)
Black
0.196 Nm
(2.0 kgfcm)
3
M2 × 5 mm, flat-head, nylon-coated (2)
Black
0.196 Nm
(2.0 kgfcm)
4
5
4
5
ThinkPad Z60t
73
Removing and replacing a FRU
1120 Speaker assembly
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
v “1110 Keyboard bezel” on page 72
1
1
1
1
Step
Screw (quantity)
Color
Torque
1
M2 × 3 mm, flat-head, nylon-coated (4)
Black
0.196 Nm
(2.0 kgfcm)
(continued)
74
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
3
3
2
When installing: Make sure that the speaker cables are routed along the cable
guides 3 and that the connector 2 is attached firmly.
4
4
4
5
5
4
4
ThinkPad Z60t
75
Removing and replacing a FRU
1130 Fan assembly
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
v “1110 Keyboard bezel” on page 72
1
1
Step
Screw (quantity)
Color
Torque
1
M2 × 5 mm, flat-head, nylon-coated (4)
Black
0.196 Nm
(2.0 kgfcm)
3
2
76
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
When installing:
v Before you attach the fan assembly to the computer, apply thermal grease on the
part marked a as in the following figure.
a
v Make sure that the fan connector is attached firmly.
v When attaching the fan assembly to the frame, take care not to damage the heat
sink (b) of the fan assembly.
b
b
ThinkPad Z60t
77
Removing and replacing a FRU
1140 CPU
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
v “1110 Keyboard bezel” on page 72
v “1130 Fan assembly” on page 76
Attention: CPU is extremely sensitive. When you service the CPU, avoid any
kind of rough handling.
Rotate the head of the screw in the direction shown by arrow 1 to release the
lock; then remove the CPU 2.
1
a
b
2
When installing: Place the CPU on the CPU socket a, and then rotate the head
of the screw in the direction shown by arrow b to secure the
CPU.
78
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
1150 Wireless WAN antenna (DIV)
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
v “1080 PCI Express Mini card for wireless WAN” on page 67
Strip the tape that secures the wireless WAN antenna 1, and release the antenna
cable from the cable guide. Then slide the antenna in the direction shown by arrow
2.
a
2
1
a
When installing: Make sure that the antenna cable is routed along the cable
guides, and that the antenna is attached to the guides a firmly.
ThinkPad Z60t
79
Removing and replacing a FRU
1160 LCD assembly
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
v “1070 Modem daughter card (MDC-1.5)” on page 65
v “1080 PCI Express Mini card for wireless WAN” on page 67
v “1090 PCI Express Mini card for wireless LAN” on page 69
v “1110 Keyboard bezel” on page 72
1
1
Step
Screw (quantity)
Color
Torque
1
M2 × 5 mm, flat-head, nylon-coated (2)
Black
0.196 Nm
(2.0 kgfcm)
(continued)
80
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
4
4
2
b
a
a
3
In step 3, release the antenna cables from the cable guides.
Step
Screw (quantity)
Color
Torque
4
M2 × 5 mm, flat-head, nylon-coated (2)
Black
0.245 Nm
(2.5 kgfcm)
When installing:
1. Make sure that the antenna cables are routed along the cable guides. In the
parts indicated by circle a in the figure, do not tense the cables. To do so, the
cables may get damaged by the cable guides of the frame, and may cause a
broken wire.
2. In the part indicated by circle b, do not twist the cables, and place the cables
to be parallel.
3. Make sure that the connector 2 is attached firmly.
(continued)
ThinkPad Z60t
81
Removing and replacing a FRU
5
5
82
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
1170 Base cover
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 56
v “1020 Ultrabay Slim device” on page 57
v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails”
on page 58
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
v “1070 Modem daughter card (MDC-1.5)” on page 65
v “1080 PCI Express Mini card for wireless WAN” on page 67
v “1090 PCI Express Mini card for wireless LAN” on page 69
v “1110 Keyboard bezel” on page 72
v “1120 Speaker assembly” on page 74
v “1130 Fan assembly” on page 76
v “1150 Wireless WAN antenna (DIV)” on page 79
v “1160 LCD assembly” on page 80
1b
1a
1b
1b
1a
1b
Step
Screw cap
1a
1b
—
Screw (quantity)
Color
Torque
M2 × 5 mm, flat-head, nylon-coated
(2)
Black
0.196 Nm
(2.0 kgfcm)
M2 × 5 mm, flat-head, nylon-coated
(6)
Black
0.196 Nm
(2.0 kgfcm)
(continued)
ThinkPad Z60t
83
Removing and replacing a FRU
In step 2, lift the MG frame a little in the direction shown by the arrow, and then
remove it in the direction shown by arrow 3.
Attention: Before step 2, be sure that the Ultrabay Slim device eject lever is not
popped out and it is housed in its position properly as shown in the figure a.
3
2
a
84
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
Note: Applying labels to the base cover
The new base cover FRU is shipped with a kit containing labels of several
kinds. When you replace the base cover, you need to apply the following
labels:
a Windows license label (COA)
b Product label
c FCC or homologation label
d MAC address label
For some models, you also need to apply one or two FCC labels c. Check
the old base cover; if it has one or two FCC labels, find duplicates of them in
the label kit and apply them to the new base cover.
Apply the labels to the base cover as shown in this figure.
a
b
c
d
ThinkPad Z60t
85
Removing and replacing a FRU
1180 USB/S-video sub card with cable
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 56
v “1020 Ultrabay Slim device” on page 57
v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails”
on page 58
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
v “1070 Modem daughter card (MDC-1.5)” on page 65
v “1080 PCI Express Mini card for wireless WAN” on page 67
v “1090 PCI Express Mini card for wireless LAN” on page 69
v “1110 Keyboard bezel” on page 72
v “1120 Speaker assembly” on page 74
v “1130 Fan assembly” on page 76
v “1150 Wireless WAN antenna (DIV)” on page 79
v “1160 LCD assembly” on page 80
v “1170 Base cover” on page 83
2
2
3
1
Step
Screw (quantity)
Color
Torque
2
M2 × 3 mm, flat-head, nylon-coated (2)
Black
0.196 Nm
(2.0 kgfcm)
When installing: Make sure that the connector 1 is attached firmly, and that the
cable is routed as in the figure above.
86
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
1190 MG (Magnesium) frame
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 56
v “1020 Ultrabay Slim device” on page 57
v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails”
on page 58
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1050 DIMM” on page 62
v “1060 Keyboard” on page 63
v “1070 Modem daughter card (MDC-1.5)” on page 65
v “1080 PCI Express Mini card for wireless WAN” on page 67
v “1090 PCI Express Mini card for wireless LAN” on page 69
v “1110 Keyboard bezel” on page 72
v “1120 Speaker assembly” on page 74
v “1130 Fan assembly” on page 76
v “1150 Wireless WAN antenna (DIV)” on page 79
v “1160 LCD assembly” on page 80
v “1170 Base cover” on page 83
v “1180 USB/S-video sub card with cable” on page 86
ThinkPad Z60t
87
Removing and replacing a FRU
Remove the ac power jack cable a and the modem cable b.
2
a
b
4
1
3
3
When installing: Make sure that the connectors 1 and 3 are attached firmly,
and that the cables are routed as in the figure above.
(continued)
88
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
Remove the CPU support plate c.
5
c
5
5
5
6
Step
Screw (quantity)
Color
Torque
6
M2 × 3 mm, flat-head, nylon-coated (4)
Black
0.196 Nm
(2.0 kgfcm)
(continued)
ThinkPad Z60t
89
Removing and replacing a FRU
8
9
7
8
7
7
7
7
10
10
Step
Screw (quantity)
Color
Torque
7
M2 × 3 mm, flat-head, nylon-coated (5)
Black
0.196 Nm
(2.0 kgfcm)
8
M2 × 9 mm, flat-head, nylon-coated (2)
Black
0.196 Nm
(2.0 kgfcm)
9
M2 × 5 mm, flat-head, nylon-coated (1)
Black
0.196 Nm
(2.0 kgfcm)
In step 10, loosen the hex screws.
(continued)
90
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
Remove the system board and the PC Card slot assembly from the MG frame
together, in the direction shown by arrow 12.
12
11
11
When installing: Attach the system board so that the two small projections on the
MG frame 11 fit into the holes provided, and then secure the
system board with the screw.
ThinkPad Z60t
91
Removing and replacing a FRU
1200 System board and PC Card slot assembly
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 56
v “1020 Ultrabay Slim device” on page 57
v “1030 Hard disk drive cover, hard disk drive, and hard disk drive rubber rails”
on page 58
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1050 DIMM” on page 62
v “1060 Keyboard” on page 63
v “1070 Modem daughter card (MDC-1.5)” on page 65
v “1080 PCI Express Mini card for wireless WAN” on page 67
v “1090 PCI Express Mini card for wireless LAN” on page 69
v “1110 Keyboard bezel” on page 72
v “1120 Speaker assembly” on page 74
v “1130 Fan assembly” on page 76
v “1140 CPU” on page 78
v “1150 Wireless WAN antenna (DIV)” on page 79
v “1160 LCD assembly” on page 80
v “1170 Base cover” on page 83
v “1180 USB/S-video sub card with cable” on page 86
v “1190 MG (Magnesium) frame” on page 87
92
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
Important notice for handling the system board
When handling the system board, bear the following in mind.
v The system board has an accelerometer, which can be broken by applying
several thousands of G-forces.
Note: Dropping a system board from a height of as little as 6 inches so
that it falls flat on a hard bench can subject the accelerometer to as
much as 6,000 G’s of shock.
v Be careful not to drop the system board on a bench top that has a hard
surface, such as metal, wood, or composite.
v If a system board is dropped, you must test it, using PC-Doctor for DOS, to
make sure that the HDD Active Protection still functions (see below).
Note: If the test shows that HDD Active Protection is not functioning, be
sure to document the drop in any reject report, and replace the
system board.
v Avoid rough handling of any kind.
v At every point in the process, be sure not to drop or stack the system
board.
v If you put a system board down, be sure to put it only on a padded
surface such as an ESD mat or conductive corrugated material.
After replacing the system board, run PC-Doctor for DOS to make sure that
HDD Active Protection still functions. The procedure is as follows:
1. Place the computer on a horizontal surface.
2. Run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test.
Attention: Do not apply physical shock to the computer while the test is
running.
ThinkPad Z60t
93
Removing and replacing a FRU
Following components soldered on the system board are extremely sensitive. When
you service the system board, avoid any kind of rough handling.
a Accelerometer chip for the HDD Active Protection System
b MCH (Memory ControllerHub)
c ICH (I/O Controller Hub)
d Security chip
e CPU
a
b
c
d
e
94
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
Important
When handling the system board, bear the following in mind.
v The system board has an accelerometer, which can be broken by applying
several thousands of G-forces.
Note: Dropping a system board from a height of as little as 6 inches so
that it falls flat on a hard bench can subject the accelerometer to as
much as 6,000 G’s of shock.
v Be careful not to drop the system board on a bench top that has a hard
surface, such as metal, wood, or composite.
v If a system board is dropped, you must test it, using PC-Doctor for DOS, to
make sure that the HDD Active Protection still functions (see below).
Note: If the test shows that HDD Active Protection is not functioning, be
sure to document the drop in any reject report, and replace the
system board.
v Avoid rough handling of any kind.
v At every point in the process, be sure not to drop or stack the system
board.
v If you put a system board down, be sure to put it only on a padded
surface such as an ESD mat or conductive corrugated material.
After replacing the system board, run PC-Doctor for DOS to make sure that
HDD Active Protection still functions. The procedure is as follows:
1. Place the computer on a horizontal surface.
2. Run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test.
Attention: Do not apply physical shock to the computer while the test is
running.
ThinkPad Z60t
95
Removing and replacing a FRU
2
2
2
2
1
Step
Screw (quantity)
Color
Torque
2
M2 × 5 mm, flat-head, nylon-coated (4)
Black
0.196 Nm
(2.0 kgfcm)
Turn over the system board, and then disconnect the PC Card slot assembly from
the system board.
3
When installing: Make sure that the connector of PC Card slot is attached to the
system board firmly.
96
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
2010 LCD front bezel
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
v “1070 Modem daughter card (MDC-1.5)” on page 65
v “1080 PCI Express Mini card for wireless WAN” on page 67
v “1090 PCI Express Mini card for wireless LAN” on page 69
v “1110 Keyboard bezel” on page 72
v “1160 LCD assembly” on page 80
1
1
1
Step
Screw cap
1
Screw (quantity)
Color
Torque
M2 × 5 mm, flat-head, nylon-coated
(3)
Black
0.196 Nm
(2.0 kgfcm)
(continued)
ThinkPad Z60t
97
Removing and replacing a FRU
In step 3, while sliding the LCD latch lever in the direction shown by the arrow,
remove the bezel in the direction shown by arrow 4.
3
4
2
2
2
2
2
2
98
MT 2511, 2512, 2513, and 2514
2
2
Removing and replacing a FRU
2020 Inverter card
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
v “1070 Modem daughter card (MDC-1.5)” on page 65
v “1080 PCI Express Mini card for wireless WAN” on page 67
v “1090 PCI Express Mini card for wireless LAN” on page 69
v “1110 Keyboard bezel” on page 72
v “1160 LCD assembly” on page 80
v “2010 LCD front bezel” on page 97
1
2
3
When installing: Make sure that connectors 2 and 3 are attached firmly.
Cable routing: When installing the inverter card, route the connector cable as in
this figure.
ThinkPad Z60t
99
Removing and replacing a FRU
2030 Bluetooth daughter card (BDC-2)
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
v “1070 Modem daughter card (MDC-1.5)” on page 65
v “1080 PCI Express Mini card for wireless WAN” on page 67
v “1090 PCI Express Mini card for wireless LAN” on page 69
v “1110 Keyboard bezel” on page 72
v “1160 LCD assembly” on page 80
v “2010 LCD front bezel” on page 97
1
2
3
100
Step
Screw (quantity)
Color
Torque
1
M2 × 5 mm, flat-head, nylon-coated (1)
Black
0.196 Nm
(2.0 kgfcm)
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
When installing: Make sure that connector is attached firmly, and that the card is
attached to the guide as in this figure.
ThinkPad Z60t
101
Removing and replacing a FRU
2040 Wireless WAN antenna cable (MAIN)
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
v “1070 Modem daughter card (MDC-1.5)” on page 65
v “1080 PCI Express Mini card for wireless WAN” on page 67
v “1090 PCI Express Mini card for wireless LAN” on page 69
v “1110 Keyboard bezel” on page 72
v “1160 LCD assembly” on page 80
v “2010 LCD front bezel” on page 97
v “2020 Inverter card” on page 99
v “2030 Bluetooth daughter card (BDC-2)” on page 100
Strip the tape securing the antenna cable 1. Then remove the antenna cable.
3
1
2
3
2
102
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
When installing: In step 2, press the part indicated by the arrow until it snaps
into place.
1
1
3
2
ThinkPad Z60t
103
Removing and replacing a FRU
Cable routing: Route the antenna cable as shown in this figure. In the part
indicated by circle a, do not tense the cable. To do so, the cable
may get damaged by the hinge, and may cause a broken wire.
a
104
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
2050 LCD panel, LCD cable, and hinges
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
v “1070 Modem daughter card (MDC-1.5)” on page 65
v “1080 PCI Express Mini card for wireless WAN” on page 67
v “1090 PCI Express Mini card for wireless LAN” on page 69
v “1110 Keyboard bezel” on page 72
v “1160 LCD assembly” on page 80
v “2010 LCD front bezel” on page 97
v “2020 Inverter card” on page 99
v “2030 Bluetooth daughter card (BDC-2)” on page 100
v “2040 Wireless WAN antenna cable (MAIN)” on page 102
1
2
1
1
2
1
Step
Screw (quantity)
Color
Torque
1
M2 × 3 mm, flat-head, nylon-coated (4)
Silver
0.196 Nm
(2.0 kgfcm)
2
M2 × 5 mm, flat-head, nylon-coated (2)
Black
0.196 Nm
(2.0 kgfcm)
(continued)
ThinkPad Z60t
105
Removing and replacing a FRU
3
6
5
4
(continued)
106
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
Remove the hinges a from the LCD panel.
a
7
7
8
a
8
7
7
Step
Screw (quantity)
Color
Torque
7
M2 × 3 mm, small-head, nylon-coated (4)
Silver
0.196 Nm
(2.0 kgfcm)
Remove the LCD cable assembly b from the LCD panel.
9
b
10
When installing: When replacing any LCD FRUs, be sure not to pinch the antenna
cables. Make sure that the cables are routed as shown in the
figures on page 112 and 113.
ThinkPad Z60t
107
Removing and replacing a FRU
2060 LCD rear cover and wireless LAN antenna cables
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1040 Palm rest or palm rest with fingerprint reader” on page 60
v “1060 Keyboard” on page 63
v “1070 Modem daughter card (MDC-1.5)” on page 65
v “1080 PCI Express Mini card for wireless WAN” on page 67
v “1090 PCI Express Mini card for wireless LAN” on page 69
v “1110 Keyboard bezel” on page 72
v “1160 LCD assembly” on page 80
v “2010 LCD front bezel” on page 97
v “2020 Inverter card” on page 99
v “2030 Bluetooth daughter card (BDC-2)” on page 100
v “2040 Wireless WAN antenna cable (MAIN)” on page 102
v “2050 LCD panel, LCD cable, and hinges” on page 105
Strip the tapes 1 and 2 that secure the antenna cables.
2
1
1
1
1
1
(continued)
108
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
Remove the LCD latches before you remove the antenna cables.
3
4
5
(continued)
ThinkPad Z60t
109
Removing and replacing a FRU
When installing: Attache the latches as shown in this figure.
1
2
3
4
110
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
7
6
6
6
7
6
(continued)
ThinkPad Z60t
111
Removing and replacing a FRU
Cable routing: Route and secure the antenna cables as shown in the following
figures.
Wireless LAN antenna cable (AUX: black)
a
(continued)
112
MT 2511, 2512, 2513, and 2514
Removing and replacing a FRU
Wireless LAN antenna cable (MAIN: gray)
a
ThinkPad Z60t
113
Locations
Locations
Front view
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
ThinkLight
Status indicators
Note: For the description of each indicator, see “Status indicators” on page
36.
Wireless WAN antenna
Security key hole
Universal serial bus (USB) connectors
Ultrabay Slim status indicator
Ultrabay Slim latch
Ultrabay Slim
IEEE 1394 connector
PC Card slot
Fingerprint reader (for some models)
TrackPoint buttons
Touch pad buttons
Touch pad
UltraNav
TrackPoint pointing stick
Volume control buttons
ThinkVantage button
Power switch
1
19
2
18
17
16
3
4
5
14
6
13
15
7
8
12
11
114
MT 2511, 2512, 2513, and 2514
9
10
5
Locations
Rear view
1
2
3
4
5
6
Status indicators
Note: For the description of each indicator, see “Status indicators” on page
36.
RJ-45 (Ethernet) connector
RJ-11 (modem) connector
External monitor connector
AC power connector
Video-out connector
1
6
2
3
5
4
ThinkPad Z60t
115
Locations
Bottom view
1
2
3
4
5
6
7
8
9
Battery pack
Battery pack latch
Docking connector
Hard disk drive
Stereo headphone jack
Microphone jack
Wireless radio switch
Infrared port
SD card slot
1
9
8
7
6
2
3
5
4
116
MT 2511, 2512, 2513, and 2514
Parts list
Parts list
v Each FRU is available for all types or models, unless specific types or models are
specified.
v FRU with specific models listed and described as xxU (where U is an example of
a country designator) should be used for all models ending in U.
v FRU with specific models listed and described as 3Dx (where 3D is an example
of a unique configuration) should be used for all of these models, unless specific
country or region designator is specified.
v A CRU (customer replaceable unit) is identified by a single asterisk (*) or two
asterisks (**) in the CRU ID column. An N in the CRU ID column means the
part is not a CRU. A single asterisk (*) means the part is an External CRU; two
asterisks (**) means the part is an Internal CRU.
ThinkPad computers contain the following types of the external CRUs:
External CRUs (pluggable)
These CRUs unplug from the computer. Examples of these types of
CRUs include an ac adapter, an external keyboard, a mouse, a power
cord, a port replicator, a USB device, and an external bay device adapter.
External CRUs with latches
These CRUs have a latch to help you to remove and replace the part.
Examples of these types of CRUs include a battery pack, an Ultrabay
device such as an optical drive, a hard disk drive, and an extended
battery.
ThinkPad computers contain the following types of the internal CRUs:
Internal CRUs (located behind an access panel)
These CRUs are isolated parts within the computer that are concealed by
an access panel that is typically secured by either one or two screws.
Once the access panel is removed, only the specific CRU is visible.
Examples of these types of CRUs include a memory card and a hard
disk drive.
Internal CRUs (located within the product itself)
These CRUs are accessible only by opening the outer case of the
computer. Examples of these CRUs include the integrated keyboard
parts beneath the integrated keyboard and parts beneath the palm rest.
v A RoHS compliant FRU is identified by an R. An N in the RoHS ID column
means the part is not a RoHS compliant FRU.
v FRUs marked with OP are available as options.
ThinkPad Z60t
117
Parts list
Overall
1
24
23
2
3
d
22
a
21
4
20
5
19
6
7
8
9
18
c
10
17
11
b
12
13
16
14
15
118
MT 2511, 2512, 2513, and 2514
Parts list
No.
FRU
a-d
See “Miscellaneous parts” on page 131.
P/N
CRU
ID
1
LCD unit (see “LCD FRUs” on page 126.)
2
Keyboard bezel assembly
41V9786
N
3
Palm rest assembly without fingerprint reader
v 2511-CTO, E1x
v 2511-H1x, H3x
v 2512-CTO, 11x, 12x, 13x, 14x, 15x, 18x, 1Ax, 1Dx, 1Ex,
1Fx, 1Gx, 1Jx, 1Mx, 1Nx, 1Px, 1Ux, 1Zx, 24x, 26x, 2Dx,
38x, 4Hx, 4Jx, E1x
v 2512-JFx, JGx, JHx
v 2513-CTO, 11x, 14x, 1Ax, 1Fx, 1Nx, 24x, 62x, 67x, 6Gx,
6Px, 7Cx, 7Jx
v 2514-CTO, 11x, 1Dx, 7Cx
41V9788
**
Palm rest assembly with fingerprint reader
v 2511-CTO, 3Bx, 5xx, Exx except E1x, Fxx
v 2511-H2x, H4x, H5x, H6x, H7x, H8x, H9x, HAx, Pxx
v 2512-CTO, 16x, 19x, 1Bx, 1Cx, 1Qx, 1Rx, 1Sx, 1Tx, 22x,
25x, 27x, 28x, 29x, 2Ax, 2Bx, 2Ex, 2Fx, 31x, 32x, 3Ax,
3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 44x, 47x, 48x, 49x,
4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Mx, 4Nx, 4Px, 51x,
52x, 64x, E6x, F4x
v 2512-J1x, J2x, J3x, J4x, J5x, J6x, J7x, J8x, J9x, JAx, JBx,
JDx, JEx, JJx, JKx, JLx, JMx, JPx, JQx, JRx
v 2513-CTO, 19x, 1Cx, 28x, 29x, 2Ax, 2Ex, 2Fx, 37x, 3Ax,
3Bx, 4Mx, 63x, 64x, 6Ax, 6Ex, 6Hx, 6Jx, 6Kx, 6Mx, 6Rx,
73x, 74x, 79x, 7Bx, 7Dx, 7Ex, 7Fx, 7Gx, E4x, E5x
v 2513-Mxx
v 2514-CTO, 3Ax, 3Bx, 79x
v 2514-Mxx
41V9790
**
4
Speaker assembly
39T7220
N
5
Magnesium frame
41V9784
N
6
Modem daughter card (MDC-1.5)
39T0495
**
7
ThinkPad 11a/b/g Wireless LAN Mini PCI Express Adapter
WW
39T0499
**
BG
39T5617
**
Japan
39T5613
**
Korea
41W1073
**
Taiwan
39T5615
**
39T5664
N
8
Sierra Wireless EV-DO Wireless WAN Mini PCI Express
Adapter
v 2511-CTO, E7x, EGx
v 2511-H8x
v 2512-CTO
v 2513-CTO, 7Bx, 7Dx, 7Ex
v 2514-CTO
(continued)
ThinkPad Z60t
119
Parts list
No.
FRU
P/N
CRU
ID
9
USB/S-video sub card with cable
39T5622
N
10
PC Card slots
26R9553
N
11
System board with Intel 915GM
39T5618
N
12
Backup battery
92P1161
**
13
Battery pack, Li-ion (4 cell)
v 2511-CTO, E1x, E8x, E9x, EAx, EBx, EEx, EJx, EMx, FCx
v 2511-H1x, H4x, H5x, H6x
v 2512-CTO, 11x, 13x, 14x, 15x, 18x, 19x, 1Ex, 1Fx, 1Gx, 1Jx, 1Zx, 2Bx, 2Dx, 2Ex, 2Fx,
32x, 38x, 3Ax, 3Cx, 3Dx, 3Ex, 3Fx, 44x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex,
4Fx, 4Gx, 4Hx, 4Jx, 4Mx, 4Nx, 4Px, E1x
v 2512-J1x, J3x, J4x, J5x, J6x, J7x, J8x, J9x, JAx, JBx, JDx, JEx, JFx, JGx, JHx, JLx, JMx,
JPx, JQx
v 2513-CTO, 11x, 14x, 19x, 1Fx, 2Ex, 2Fx, 37x, 3Ax, 4Mx, 62x, 67x, 6Px, 73x, 74x, 7Jx
v 2513-M1x, M2x, M3x, M6x, M7x
v 2514-CTO, 11x, 3Ax
v 2514-M6x, MEx
14
Sanyo
92P1121
*
Panasonic
92P1123
*
Battery pack, Li-ion (7 cell) Sanyo
92P1125
v 2511-CTO, 3Bx, E2x, E3x, E4x, E5x, E6x, E7x, ECx, EDx,
EFx, EGx
v 2511-H2x, H3x, H7x, H8x, H9x, HAx
v 2512-CTO, 12x, 16x, 1Ax, 1Bx, 1Cx, 1Dx, 1Mx, 1Nx, 1Px,
1Qx, 1Rx, 1Sx, 1Tx, 1Ux, 22x, 24x, 25x, 26x, 27x, 28x,
29x, 2Ax, 31x, 3Gx, 3Hx, 3Jx, 64x, E6x
v 2512-J2x, JJx, JKx, 1Rx
v 2513-CTO, 1Ax, 1Cx, 1Nx, 24x, 28x, 29x, 2Ax, 3Bx, 63x,
64x, 6Ax, 6Ex, 6Gx, 6Hx, 6Jx, 6Kx, 6Mx, 6Rx, 79x, 7Bx,
7Vx, 7Dx, 7Ex, 7Fx, 7Gx, E4x, E5x
v 2513-M4x, M5x, M8x, M9x, MAx, MBx, MCx, MDx
v 2514-CTO, 1Dx, 3Bx, 79x, 7Cx
v 2514-M6x, MEx
*
DVD drive, 9.5mm
v 2511-CTO
v 2512-CTO
v 2513-CTO
v 2514-CTO
PCC (UJDA765)
39T2681
*
HLDS (GDR-8085N)
39T2683
*
(continued)
120
MT 2511, 2512, 2513, and 2514
Parts list
No.
14
FRU
P/N
CRU
ID
DVD/CD-RW combo drive, 9.5mm
v 2511-CTO, E1x, E2x, E4x, E8x, EAx, EBx, ECx, EEx, EFx, EGx, EJx, EMx
v 2511-H1x
v 2512-CTO, 11x, 13x, 14x, 15x, 18x, 19x, 1Dx, 1Ex, 1Fx, 1Gx, 1Jx, 1Mx, 1Nx, 1Px,
1Qx, 1Rx, 1Ux, 1Zx, 24x, 25x, 28x, 2Bx, 2Ex, 3Ex, 3Fx, 3Gx, 44x, 4Dx, 4Ex, 4Fx,
4Gx, 4Hx, 4Jx, 4Nx, 4Px, 64x, E1x
v 2512-1Rx, J1x, J2x, J3x, J6x, J7x, JDx, JEx, JFx, JGx, JHx
v 2513-CTO, 11x, 14x, 19x, 1Fx, 1Nx, 24x, 28x, 2Ex, 37x, 62x, 63x, 64x, 67x, 6Ex, 6Gx,
6Hx, 6Jx, 6Px, 74x, 79x, 7Dx, 7Fx, 7Jx, E4x
v 2513-M1x, M2x, M4x, M8x, M9x
v 2514-CTO, 11x, 1Dx, 79x
v 2514-M9x
PCC (UJDA765DL)
39T2685
*
HLDS (GCC-4246N)
39T2687
*
DVD-RAM/RW drive, 9.5mm, PCC (UJ-832B)
39T2573
v 2511-CTO, 3Bx, E3x, E5x, E6x, E7x, E9x, EDx, FCx
v 2511-H9x, HAx
v 2512-CTO, 12x, 16x, 1Ax, 1Bx, 1Cx, 1Sx, 1Tx, 27x, 29x,
2Ax, 2Dx, 2Fx, 31x, 32x, 38x, 3Ax, 3Cx, 3Dx, 3Hx, 3Jx,
47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Mx, E6x
v 2513-CTO, 1Ax, 1Cx, 29x, 2Ax, 2Fx, 3Ax, 3Bx, 4Mx, 6Ax,
6Kx, 6Mx, 6Rx, 73x, 7Bx, 7Cx, 7Ex, 7Gx, E5x
v 2514-CTO, 3Ax, 3Bx, 7Cx
*
DVD-RAM/RW drive, 9.5mm
v 2511-CTO, H2x, H3x, H4x, H5x, H6x, H7x, H8x
v 2512-CTO, J4x, J5x, J8x, J9x, JAx, JBx, JJx, JKx, JLx, JMx, JPx, JQx
v 2513-CTO, M3x, M5x, M6x, M7x, MAx, MBx, MCx, MDx, MEx, MGx
v 2514-CTO, M6x, MEx
PCC (UJ-842B)
92P6249
*
HLDS (GSA-4083N)
92P6248
*
13N5108
*
WW
v 2511-CTO, 3xx, 5xx, Exx, Fxx except xxV
v 2511-Hxx, Pxx except xxV
26R9563
N
Taiwan
v 2511-CTO, 3xV, 5xV, ExV, FxV
v 2511-HxV
26R9567
N
Travel cover
v 2511-CTO, xxJ, xxP, xxS, xxY
v 2512-CTO, xxJ, xxP, xxS, xxY
v 2513-CTO, xxJ, xxP, xxS, xxY
v 2514-CTO, xxJ, xxP, xxS, xxY
15
Base cover for 2511
(continued)
ThinkPad Z60t
121
Parts list
No.
15
FRU
P/N
CRU
ID
WW
v 2512-CTO, 1xx, 2xx, 3xx, 4xx, 5xx, 6xx, Exx, Fxx
except xxV
v 2512-Jxx except xxV
26R9564
N
Taiwan
v 2512-CTO, 1xV, 2xV, 3xV, 4xV, 5xV, 6xV, ExV, FxV
26R9568
N
WW
v 2513-CTO, 1xx, 2xx, 3xx, 4xx, 6xx, Exx except xxV
v 2513-Mxx except xxV
26R9565
N
Taiwan
v 2513-CTO, 1xV, 2xV, 3xV, 4xV, 6xV, ExV
v 2513-MxV
26R9569
N
WW
v 2514-CTO, 1xx, 3xx, 7xx except xxV
v 2514-Mxx except xxV
26R9566
N
Taiwan
v 2514-CTO, 1xV, 3xV, 7xV
26R9570
N
Base cover for 2512
Base cover for 2513
Base cover for 2514
16
Hard disk drive cover
26R9561
*
17
256-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card R
v 2511-CTO, E2x, EAx, EBx, ECx, EEx
v 2512-CTO, 13x, 14x, 15x, 1Ex, 1Fx, 1Jx, 1Mx, 1Nx, 1Px,
1Qx, 1Zx, 2Bx, 4Hx, 4Jx, 4Nx, 4Px
v 2512-J8x, J9x, JAx, JBx, JDx, JEx, JFx, JGx, JHx
v 2513-CTO, 14x, 1Fx, 1Nx, 6Gx, 6Hx, 6Px
v 2513-M8x
73P3841
**
512-MB DDR2-533 SDRAM SO-DIMM (PC2-4200) card R
v 2511-CTO, 3Bx, E1x, E3x, E4x, E5x, E6x, E8x, E9x, EDx,
EFx, EGx, EJx, EMx, FCx
v 2511-Hxx
v 2512-CTO, 11x, 12x, 16x, 18x, 19x, 1Ax, 1Cx, 1Dx, 1Gx,
1Rx, 1Sx, 1Tx, 1Ux, 22x, 24x, 25x, 28x, 2Dx, 2Ex, 2Fx,
31x, 32x, 38x, 3Ax, 3Cx, 3Dx, 3Ex, 3Fx, 3Hx, 3Jx, 44x,
47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Mx,
64x, E1x, E6x
v 2512-1Rx, J1x, J2x, J3x, J4x, J5x, J6x, J7x, JJx, JL,x JMx,
JPx, JQx
v 2513-CTO, 11x, 19x, 1Ax, 1Cx, 24x, 28x, 2Ex, 2Fx, 37x,
3Ax, 3Bx, 4Mx, 62x, 63x, 64x, 67x, 6Ex, 6Jx, 6Kx, 6Mx,
6Rx, 73x, 74x, 79x, 7Bx, 7Cx, 7Dx, 7Ex, 7Fx, 7Gx, 7Jx,
E4x, E5x
v 2513-M1x, M2x, M3x, M4x, M5x, M6x, M7x, M9x, MAx,
MBx, MEx, MGx
v 2514-CTO, 11x, 1Dx, 3Ax, 3Bx, 79x, 7Cx
v 2514-Mxx
73P3843
**
(continued)
122
MT 2511, 2512, 2513, and 2514
Parts list
No.
FRU
P/N
CRU
ID
17
1-GB DDR2-533 SDRAM SO-DIMM (PC2-4200) card R
v 2511-CTO, E7x
v 2512-CTO, 1Bx, 26x, 27x, 29x, 2Ax, 3Gx
v 2512-JKx
v 2513-CTO, 29x, 2Ax, 6Ax
v 2513-MCx, MDx
73P3845
**
18
Hard disk drive, 40 GB, 9.5 mm, 5,400 rpm
v 2511-CTO, E1x, E2x, E4x, E8x, EAx, EBx, ECx, EEx
v 2511-H1x
v 2512-CTO, 11x, 13x, 14x, 15x, 1Fx, 1Gx, 1Jx, 1Mx, 1Nx, 1Zx, 2Dx, 2Ex, 4Hx, 4Jx,
E1x
v 2512-J1x, J8x, J9x, JAx, JBx, JDx, JEx, JFx, JGx, JHx
v 2513-CTO, 11x, 14x, 1Fx, 1Nx, 2Ex, 62x, 6Gx, 6Hx, 6Px, 73x, 79x, 7Dx, 7Jx, E4x
v 2514-CTO, 11x, 79x
HGST
39T2701
*
Toshiba
39T2629
*
Hard disk drive, 60 GB, 9.5 mm, 5,400 rpm
v 2511-CTO, E3x, E5x, E9x, EDx, EFx, EGx, EJx, FCx
v 2512-CTO, 1Dx, 1Ex, 1Px, 1Qx, 1Ux, 22x, 25x, 2Bx, 2Fx, 31x, 38x, 3Ax, 3Ex, 3Fx,
44x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 64x
v 2512-J6x, J7x, JJx, JPx, JQx
v 2513-CTO, 2Fx, 3Ax, 63x, 64x, 67x, 6Rx, 74x, 7Ex, 7Fx, E5x
v 2512-M1x, M2x, M3x, M8x
v 2514-CTO, 1Dx, 3Ax
HGST
39T2703
*
Toshiba
39T2631
*
Hard disk drive, 80 GB, 9.5 mm, 5,400 rpm
v 2511-CTO, 3Bx, E6x, EMx
v 2511-H2x, H3x, H4x, H9x, HAx
v 2512-CTO, 12x, 16x, 18x, 19x, 1Ax, 1Bx, 1Cx, 1Rx, 1Sx, 1Tx, 24x, 26x, 28x, 32x,
3Cx, 3Dx, 3Gx, 3Hx, 3Jx, 47x, 48x, 4Mx, E6x
v 2512-1Rx, J2x, J3x, J4x, J5x, JLx, JMx
v 2513-CTO, 19x, 1Ax, 1Cx, 24x, 28x, 37x, 3Bx, 4Mx, 6Ax, 6Ex, 6Jx, 6Kx, 7Cx, 7Gx
v 2513-M4x, M6x, M7x, M9x, MBx, MEx
v 2514-CTO, 3Bx, 7Cx
v 2514-M6x, M9x, MEx
HGST
39T2705
*
Toshiba
39T2633
*
HGST
39T2707
*
Toshiba
39T2635
*
Hard disk drive, 100 GB, 9.5 mm, 5,400 rpm
v 2511-CTO, E7x
v 2512-CTO, 27x 29x, 2Ax
v 2512-JKx
v 2513-CTO, 2Ax, 29x, 6Mx, 7Bx
v 2513-M5x, MAx
v 2514-CTO
(continued)
ThinkPad Z60t
123
Parts list
No.
18
FRU
P/N
CRU
ID
HGST
27R2345
*
Seagate
27R2346
*
Hard disk drive, 100 GB, 9.5 mm, 7,200 rpm
v 2511-CTO, H5x, H6x, H7x, H8x
v 2513-CTO, MCx, MDx, MGx
19
Hard disk drive rubber rails
41V9756
*
20
CPU assembly, Intel Celeron M processor 360 (1.4 GHz)
v 2511-CTO, E2x, E3x, E8x, E9x, EAx, FCx
v 2512-CTO, 13x, 1Ex, 1Mx, 1Nx, 2Dx, 4Dx, 4Ex, 4Fx, 4Gx,
4Hx, 4Jx, 4Nx, 4Px
v 2513-CTO, 1Nx, 6Px, 7Jx
39T5385
N
CPU assembly, Intel Celeron M processor 370 (1.5 GHz)
v 2511-CTO, 52x, E1x, EBx, ECx, EDx
v 2512-CTO, 38x, 44x, 52x, E1x
v 2512-J6x, J7x, J8x, J9x, JAx, JBx, JDx, JEx, JFx, JGx, JHx,
JPx, JQx
39T0331
N
CPU assembly, Intel Celeron M processor 380 (1.6 GHz)
v 2511-CTO, H1x, P1x
39T5686
N
CPU assembly, Intel Pentium M processor 740 (1.73 GHz)
v 2511-CTO, 51x, E4x, E5x, EEx, EFx
v 2511-HAx, P2x, P4x
v 2512-CTO, 11x, 14x, 15x, 1Cx, 1Px, 1Qx, 1Rx, 1Ux, 1Zx,
22x, 24x, 3Ax, 3Cx, 3Dx, 3Ex, 3Fx, 4Bx, 4Cx, 51x, 64x
v 2512-1Rx, J4x, J5x
v 2513-CTO, 11x, 14x, 1Cx, 24x, 3Ax, 62x, 63x, 64x, 6Gx,
6Hx, 6Jx, E4x, E5x
v 2513-M1x
v 2514-CTO, 11x, 3Ax
39T0046
N
CPU assembly, Intel Pentium M processor 750 (1.86 GHz)
v 2511-CTO, E6x, EGx, EJx, F1x
v 2511-H9x, P3x, P5x
v 2512-CTO, 12x, 16x, 18x, 19x, 1Ax, 1Dx, 1Sx, 25x, 26x,
27x, 2Ex, 2Fx, 3Gx, E6x
v 2512-J2x
v 2513-CTO, 19x, 1Ax, 2Ex, 2Fx, 37x, 67x, 6Kx, 6Mx, 6Rx,
73x, 74x, 79x, 7Bx, 7Dx, 7Ex
v 2513-M4x
v 2514-CTO, 1Dx, 79x
v 2514-M6x
39T0047
N
(continued)
124
MT 2511, 2512, 2513, and 2514
Parts list
No.
FRU
P/N
CRU
ID
CPU assembly, Intel Pentium M processor 760 (2.0 GHz)
v 2511-CTO, 3Bx, E7x, EMx, F2x, F4x
v 2511-H2x, H3x, H4x
v 2512-CTO, 1Bx, 1Fx, 1Gx, 1Jx, 1Tx, 28x, 29x, 2Ax, 31x,
32x, 3Hx, 3Jx, 47x, 48x, 49x, 4Ax, 4Mx, F4x
v 2512-J1x, JLx, JMx
v 2513-CTO, 1Fx, 28x, 29x, 2Ax, 3Bx, 4Mx, 6Ax, 6Ex, 7Cx,
7Fx, 7Gx
v 2513-M2x, M3x, M5x, M9x, MAx, MDx
v 2514-CTO, 3Bx, 7Cx
v 2514-M9x
39T0048
N
CPU assembly, Intel Pentium M processor 770 (2.13 GHz)
v 2511-CTO, F3x, F5x
v 2511-H5x, H6x, H7x, H8x
v 2513-M7x, MEx
v 2514-MEx
39T0049
N
CPU assembly, Intel Pentium M processor 780 (2.26 GHz)
v 2512-CTO, JJx, JKx
v 2513-CTO, MBx, MCx, MGx
39T0460
N
21
Wireless WAN antenna cable (MAIN and AUX)
v 2511-CTO, E7x, EGx
v 2511-H8x, P4x, P5x
v 2513-CTO, 7Bx, 7Dx, 7Ex
91P6980
N
22
Fan and thermal device
26R9554
N
23
Keyboard (see “Keyboard” on page 128)
24
Track point stick caps
91P9642
*
20
ThinkPad Z60t
125
Parts list
LCD FRUs
10
1
2
9
8
3
4
7
a b
e
6
126
MT 2511, 2512, 2513, and 2514
5
c
d
Parts list
No.
FRU
a-d
See “Miscellaneous parts” on page 131.
P/N
CRU
ID
1
LCD front bezel
41V9783
N
2
LCD panel, 14.0-in. WXGA, Samsung
13N7010
N
LCD panel, 14.0-in. WXGA, LG
13N7012
N
3
Hinge
26R9551
N
4
Wireless WAN antenna cable (MAIN and AUX)
v 2511-CTO, E7x, EGx
v 2513-CTO, 7Bx, 7Dx, 7Ex
91P6980
N
5
LCD cover kit (black)
v 2511-CTO, 51x, 52x, E1x, E2x, E3x, E4x, E5x, E6x, E8x,
E9x, EAx, EBx, ECx, EDx, EEx, EFx, EGx, EHx, EJx, F1x,
F2x, F3x, FCx
v 2511-H1x, H2x, H3x, P1x
v 2512-CTO, 11x, 12x, 13x, 14x, 15x, 16x, 18x, 19x, 1Ax,
1Bx, 1Cx, 1Dx, 1Ex, 1Mx, 1Nx, 1Px, 1Qx, 1Rx, 1Sx, 1Ux,
1Zx, 22x, 24x, 25x, 26x, 27x, 2Bx, 2Dx, 2Ex, 2Fx, 38x,
3Ax, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 44x, 4Bx, 4Cx,
4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Nx, 4Px, 51x, 52x, 64x,
E1x, E6x
v 2512-J1x, J2x, J3x, J4x, J5x, J6x, J7x, J8x, J9x, JAx, JBx,
JDx, JEx, JFx, JGx, JHx, JPx, JQx
v 2513-CTO, 11x, 14x, 19x, 1Ax, 1Cx, 1Nx, 24x, 2Ex, 2Fx,
37x, 3Ax, 62x, 63x, 64x, 67x, 6Ex, 6Gx, 6Hx, 6Jx, 6Kx,
6Mx, 6Px, 6Rx, 73x, 74x, 79x, 7Bx, 7Cx, 7Dx, 7Ex, 7Jx,
E4x, E5x
v 2513-M1x, M2x, M3x, M4x, M5x, M6x, M7x, M8x, M9x
v 2514-CTO, 11x, 1Dx, 3Ax, 79x, 7Cx
v 2514-M6x, M9x
41V9758
N
LCD cover kit (silver)
v 2511-CTO, 3Bx, E7x, EMx, F4x, F5x
v 2511-H4x, H5x, H6x, H7x, H8x, H9x, HAx, P2x, P3x,
P4x, P5x
v 2512-CTO, 1Fx, 1Gx, 1Jx, 1Tx, 28x, 29x, 2Ax, 31x, 32x,
47x, 48x, 49x, 4Ax, 4Mx, F4x
v 2512-JJx, JKx, JLx, JMx
v 2513-CTO, 1Fx, 28x, 29x, 2Ax, 3Bx, 4Mx, 6Ax, 7Fx, 7Gx
v 2513-MAx, MBx, MCx, MDx, MEx, MGx
v 2514-CTO, 3Bx
v 2514-MEx
41V9781
N
6
Wireless LAN antenna cable
91P6954
N
7
LCD cable assembly, 14.1-in. WXGA
91P6953
N
8
Inverter card, WXGA (Sumida)
39T5620
N
Inverter card, WXGA (Foxconn)
39T5635
N
9
Bluetooth daughter card (BDC-2)
39T0497
N
10
Clear plate kit
26R9552
N
ThinkPad Z60t
127
Parts list
Keyboard
128
Language
P/N (NMB)
P/N (ALPS)
P/N (Chicony)
CRU
ID
Arabic
39T0961
39T7121
39T7181
**
Belgian
39T0962
39T7122
39T7182
Canadian, multilanguage
(445)
39T0959
39T7119
39T7179
Chinese, Traditional
39T0985
39T7145
39T7205
Czech
39T0963
39T7123
39T7183
Danish
39T0964
39T7124
39T7184
Dutch
39T0972
39T7132
39T7192
English, U.K.
39T0982
39T7142
39T7202
English, U.S.
39T0958
39T7118
39T7178
English, U.S. (International,
with a Euro symbol)
39T0983
39T7143
39T7203
Finnish, Swedish
39T0979
39T7139
39T7199
French, Canadian (058)
39T0960
39T7120
39T7009
French, European
39T0966
39T7126
39T7186
German
39T0967
39T7127
39T7187
Greek
39T0968
39T7128
39T7188
Hebrew
39T0970
39T7130
39T7190
Hungarian
39T0969
39T7003
39T7189
Italian
39T0971
39T7131
39T7191
Japanese
39T0984
39T7144
39T7010
Korean
39T7213
39T7215
39T7011
Norwegian
39T0973
39T7004
39T7193
Polish
39T0974
39T7134
39T7194
Portuguese
39T0975
39T7135
39T7195
Russian
39T0976
39T7136
39T7196
Slovak
39T0977
39T7005
39T7197
Slovenian
39T0978
39T7006
39T7198
Spanish, European
39T0965
39T7002
39T7185
Spanish, Latin American
39T0987
39T7147
39T7008
Swiss
39T0980
39T7007
39T7200
Thai
39T0986
39T7146
39T7206
Turkish
39T0981
39T7141
39T7201
MT 2511, 2512, 2513, and 2514
Parts list
Recovery CDs
Windows XP Professional
Windows XP Professional is preinstalled as the operating system in the following
models:
v 2511-CTO, 3Bx, E2x, E3x, E4x, E5x, E6x, E7x, E8x, E9x, ECx, EDx, EFx, EGx, EJx,
EMx
v 2511-H2x, H4x, H5x, H6x, H7x, H8x, H9x, HAx
v 2512-CTO, 11x, 12x, 15x, 1Bx, 1Dx, 1Fx, 1Gx, 1Nx, 1Ux, 22x, 24x, 26x, 27x, 28x,
29x, 2Ax, 2Dx, 2Ex, 2Fx, 31x, 32x, 38x, 3Ax, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx,
47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Mx, E6x
v 2512-J1x, J4x, J5x, J6x, J7x, J8x, J9x, JHx, JJx, JKx, JLx, JMx, JPx, JQx
v 2513-CTO, 11x, 1Fx, 1Nx, 24x, 28x, 29x, 2Ex, 2Fx, 37x, 3Ax, 3Bx, 63x, 6Ax, 6Ex,
6Gx, 6Hx, 6Jx, 6Kx, 6Mx, 6Px, 6Rx, 73x, 74x, 79x, 7Bx, 7Vx, 7Dx, 7Ex, 7Fx, 7Gx,
7Jx, E4x, E5x
v 2513-Mxx
v 2514-CTO, 11x, 1Dx, 3Ax, 3Bx, 79x, 7Cx
v 2514-Mxx
Language
P/N
CRU ID
Arabic
42J4834
*
Chinese, Simplified
42J4827
Chinese, Traditional
42J4828
Chinese, Traditional (Hong Kong S.A.R.)
42J4829
Czech
42J4833
Danish
42J4823
Dutch
42J4826
English, Russia
42J4816
English, U.K.
42J4815
English, U.S.
42J4814
Finnish
42J4824
French
42J4817
German
42J4818
Greek
42J4838
Hebrew
42J4831
Hungarian
42J4837
Italian
42J4820
Japanese
42J4830
Korean
42J4839
Norwegian
42J4825
Polish
42J4832
Portuguese, Brazilian
42J4821
Russian
42J4835
Slovak
42J4840
Spanish
42J4819
Swedish
42J4822
Turkish
42J4836
ThinkPad Z60t
129
Parts list
Windows XP Home Edition
Windows XP Home Edition is preinstalled as the operating system in the following
models:
v 2511-CTO, E1x, EAx, EBx, EEx, FCx
v 2511-H1x, H3x
v 2512-CTO, 13x, 14x, 16x, 18x, 19x, 1Ax, 1Cx, 1Ex, 1Jx, 1Mx, 1Px, 1Qx, 1Rx, 1Sx,
1Tx, 1Zx, 25x, 2Bx, 44x, 4Fx, 4Gx, 4Hx, 4Jx, 4Nx, 4Px, 64x, E1x, E6x
v 2512-J2x, J3x, JAx, JBx, JDx, JEx, JFx, JGx
v 2513-CTO, 14x, 19x, 1Ax, 1Cx, 62x, 64x, 67x
v 2514-CTO
130
Language
P/N
CRU ID
Arabic
42J5050
*
Chinese, Simplified
42J5043
Chinese, Traditional
42J5044
Chinese, Traditional (Hong Kong S.A.R.)
42J5045
Czech
42J5049
Danish
42J5039
Dutch
42J5042
English, Russia
42J5032
English, U.K.
42J5031
English, U.S.
42J5030
Finnish
42J5040
French
42J5033
German
42J5034
Greek
42J5054
Hebrew
42J5047
Hungarian
42J5053
Italian
42J5036
Japanese
42J5046
Korean
42J5055
Norwegian
42J5041
Polish
42J5048
Portuguese, Brazilian
42J5037
Russian
42J5051
Spanish
42J5035
Swedish
42J5038
Turkish
42J5052
MT 2511, 2512, 2513, and 2514
Parts list
Miscellaneous parts
FRU
P/N
CRU ID
Screw kit (including nylon-coated screws):
v M2 × 3 mm (silver), small head (8)
v M2 × 3 mm (black), flat head (31)
v M2 × 5 mm (black), flat head (28)
v M2 × 9 mm (black), flat head (2)
v M2 × 14 mm (black), flat head (7)
v M3 × 3 mm (PHILLIPS/slotted) (1)
v Hex stud (2)
v Security screw (1)
v Screw caps (oval, not painted)
26R9547
N
System miscellaneous parts:
v Cable, RJ11-docking connector on system board
v (a) DC in cable
26R9546
N
Base miscellaneous parts:
v Rubber foot
v Insulation sheet
v Gasket
26R9545
N
System board miscellaneous parts:
v (d) MDC cable
v (c) CPU support plate
v Magnetic tape
v Gasket
26R9544
N
26R9548
N
Note: Italicized letter in parentheses is reference to the exploded
view on page 118.
Note: Italicized letters in parentheses are references to the
exploded view on page 118.
LCD assembly miscellaneous parts:
v (a) LCD latch R
v (b) Coil spring
v (c) Link wire
v (d) LCD latch L
v (e) Cable bush
v Wireless WAN antenna cover
Note: Italicized letters in parentheses are references to the
exploded view on page 126.
ThinkPad Z60t
131
Parts list
AC adapters
FRU
P/N
CRU
ID
3-pin (90 W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxQ, xxV)
OP
ASTEC
92P1104
*
Lite-On
92P1108
*
Sanken
92P1112
*
2-pin (90W, 20 V) slim adapter for non-PFC model (models CTO, xxE, xxF, xxJ, xxL, xxP,
xxS, xxU, xxY) OP
ASTEC
92P1106
*
Lite-On
92P1110
*
Sanken
92P1114
*
Common parts list
Tools
Tool
P/N
Screwdriver kit
95F3598
1/4" drive spinner handle
1650840
1/4" Sq. to 1/4" hex torx adapter
93F2838
TR7-TR-10 tamper resistant torx bits
00P6967
Removal tool antenna RF connector
08K7159
USB 2.0 CD-RW/DVD-ROM combo drive II
40Y8687
USB cable
40Y8704
USB floppy diskette drive for maintenance diskette
05K9283
USB floppy diskette drive tool kit
27L3452
Test card for integrated Smart Card
42W7820
ThinkPad Hardware Maintenance Diskette Version 1.73 or later
—
Note: Download the file from the following Web site: http://www.lenovo.com/
spm
132
MT 2511, 2512, 2513, and 2514
Parts list
Power cords (system)
A ThinkPad power cord for a specific country or region is usually available only in
that country or region:
For 2-pin power cords:
Region
P/N
CRU ID
Canada, U.S. R
v models -CTO, xxF, xxL, xxS, xxU
39M5016
*
Japan R
v models -Exx, Jxx
39M5040
Argentina R
v models -CTO, xxY
39M5020
Brazil R
v models -CTO, xxP
39M5056
For 3-pin power cords:
Region
P/N
CRU ID
Australia, New Zealand R
v models -CTO, xxG, xxM
39M4960
*
Taiwan, Thailand R
v models -CTO, xxV
39M4955
Italy R
v models -CTO, xxG
39M4984
Denmark R
v models -CTO, xxG
39M4968
U.K., China (Hong Kong S.A.R.) R
v models -CTO, xxB, xxG, xxH
39M4976
European countries R
v models -CTO, xxG
39M4964
India, South Africa R
v models -CTO, xxG
39M4972
Israel R
v models -CTO, xxG
39M4988
Korea R
v models -xxK
39M5000
China (P.R.C.) (other than Hong Kong S.A.R.) R
v models -xxC
39M4996
Switzerland R
v models -CTO, xxG
39M4980
ThinkPad Z60t
133
Notices
Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area. Any
reference to a Lenovo product, program, or service is not intended to state or
imply that only that Lenovo product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe any
Lenovo intellectual property right may be used instead. However, it is the user’s
responsibility to evaluate and verify the operation of any other product, program,
or service.
Lenovo may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents. You can send license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF
ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some
jurisdictions do not allow disclaimer of express or implied warranties in certain
transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. Lenovo may make improvements
and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
The products described in this document are not intended for use in implantation
or other life support applications where malfunction may result in injury or death
to persons. The information contained in this document does not affect or change
Lenovo product specifications or warranties. Nothing in this document shall
operate as an express or implied license or indemnity under the intellectual
property rights of Lenovo or third parties. All information contained in this
document was obtained in specific environments and is presented as an
illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those Web
sites. The materials at those Web sites are not part of the materials for this Lenovo
product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled
environment. Therefore, the result obtained in other operating environments may
vary significantly. Some measurements may have been made on development-level
systems and there is no guarantee that these measurements will be the same on
generally available systems. Furthermore, some measurements may have been
134
MT 2511, 2512, 2513, and 2514
Notices
estimated through extrapolation. Actual results may vary. Users of this document
should verify the applicable data for their specific environment.
Trademarks
The following terms are trademarks of Lenovo in the United States, other countries
or both:
Active Protection System
Lenovo
Rescue and Recovery
ThinkLight
ThinkPad
ThinkVantage
TrackPoint
Ultrabay
Ultrabay 2000
Ultrabay Plus
UltraNav
The following terms are trademarks of the International Business Machines
Corporation in the United States, other countries, or both:
IBM (used under license)
Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation in
the United States, other countries, or both.
Intel and Pentium are trademarks or registered trademarks of Intel Corporation or
its subsidiaries in the United States and other countries.
Other company, product, or service names may be the trademarks or service marks
of others.
ThinkPad Z60t
135
Part Number: 39T6194_01
(1P) P/N: 39T6194_01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement