2001 sx om
p/n: 042028
28209 Avenue Stanford, Valencia, California 91355-3984
•
Phone: 661.257.4411
•
Sales Fax: 661.294.4179
.3.
.5.
Grease port
Schmieröffnung
Orificio de engrasado
Graisseur
Apertura per l’ingrassaggio
Smeergat
Orifício de lubrificação
Fine tuning compression spring
Feinabstimmung der Druckfeder
Ajustes de precisión al resorte
de compresión
Réglages fins des ressorts
de compression
Messa a punto della molla
di compressione
Fijnafstelling van drukveer
Mola de compressão de ajuste preciso
ROTATE
RUOTARE
DREHEN
DRAAIEN
GIRAR
GIRAR
TOURNER
.6.
Fine tuning compression damping
Feinabstimmung der
Druckstufendämpfung
Ajuste de precisión para el
sistema de amortiguación
de compresión
Réglages fins de
l’amortissement de
la compression
Messa a punto del gruppo compressione di smorzamento
Fijnafstelling van drukdemping
Ajuste de precisão do amortecimento de compressão
.4.
Oil level
Ölstand
Nivel del aceite
Niveau d’huile
Livello dell’olio
Oliepeil
Nível do óleo
MAXIMUM LEVEL
OBERSTER ÖLSTAND
NIVEL MÁXIMO
NIVEAU MAXIMUM
LIVELLO MASSIMO
MAXIMUMPEIL
NÍVEL MÁXIMO
MINIMUM LEVEL
NIEDRIGSTER ÖLSTAND
NIVEL MÍNIMO
NIVEAU MINIMUM
LIVELLO MINIMO
MINIMUMPEIL
NÍVEL MÍNIMO
RECOMMENDED LEVEL
EMPFOHLENER ÖLSTAND
NIVEL RECOMENDADO
NIVEAU RECOMMANDÉ
LIVELLO RACCOMANDATO
AANBEVOLEN PEIL
NÍVEL RECOMENDADO
ROTATE
RUOTARE
DREHEN
DRAAIEN
GIRAR
GIRAR
TOURNER
.7.
Fine tuning rebound damping
Feinabstimmung der Zugstufendämpfung
Ajuste de precisión para la amortiguación de rebote
Réglages fins de l’amortissement de la détente
Messa a punto dello smorzamento all’estensione
Fijnafstelling van terugveringdemping
Ajuste de precisão do ressalto de amortecimento
ROTATE
RUOTARE
DREHEN
DRAAIEN
GIRAR
GIRAR
TOURNER
.1.
Race Installation
Einbau des Steuersatzringes
Instalación del anillo de rodadura
Installation du jeu de direction
Montaggio dell’anello della testa
Installatie van loopring
Instalação do canalete
.2.
Tire clearance
Reifenabstand
Espacio libre de
la cubierta
Distance arceau/pneu
Spazio libero del pneumatico
Bandspeling
Folga do pneu
CROWN RACE
GABELBRÜCKEN-STEUERSATZRING
ANILLO DE RODADURA
CONE DE JEU DE DIRECTION
ANELLO DELLA TESTA
KROONLOOPRING
CANALETE DA COROA
FORK MODEL
GABELMODELL
MODELO DE HORQUILLA
MODÈLE DE FOURCHE
MODELLO DI FORCELLA
VORKMODEL
MODELO DO GARFO
MINIMUM CLEARANCE
MINDESTABSTAND
ESPACIO LIBRE MÍNIMO
JEU MINIMUM
SPAZIO LIBERO MINIMO
MINIMUMSPELING
FOLGA MÍNIMA
80 mm travel forks
100 mm travel forks
3.26” (83 mm)
4.05” (103 mm)
Gabel mit 80 mm Auslenkung
Gabel mit 100 mm Auslenkung
83 mm
103 mm
Horquillas con recorrido de 80 mm
Horquillas con recorrido de 100 mm
83 mm
103 mm
Fourches ayant une course de 80 mm
Fourches ayant une course de 100 mm
83 mm
103 mm
Forcelle con corsa da 80 mm
Forcelle con corsa da 100 mm
83 mm
103 mm
Loop van 80 mm
Loop van 100 mm
83 mm
103 mm
Curso de 80 mm
Curso de 100 mm
83 mm
103 mm
83 mm
103 mm
AMERICAN MADE MANITOU SUSPENSION
WARRANTY INFORMATION
CONGRATULATIONS ON CHOOSING THE LATEST IN SUSPENSION TECHNOLOGY AVAILABLE, A 2001 MANITOU SX BUILT IN THE USA. WITH THIS FORK INSTALLED ON
YOUR BIKE, YOU’LL BE ABLE TO RIDE FASTER AND HAVE MORE FUN. SOME WORDS
ON YOUR NEW SX BEFORE WE BEGIN. 2001 SX, SX 100MM AND SX R FORKS USE
MANITOU’S PATENTED TPC (TWIN PISTON CHAMBER) SYSTEM THAT SURPASSES ALL
OTHER TYPES OF OIL-DAMPED SYSTEMS IN PERFORMANCE AND DURABILITY. SX
FORKS ALSO USE MANITOU’S QUICK AND EASY MICROLUBE SYSTEM, WHICH
ALLOWS YOU TO LUBRICATE THE FORK VIA AN EXTERNAL FITTING ON THE BACK OF
THE FORK. ALL MANITOU FORKS COME EQUIPPED WITH 74MM POST-STYLE DISC
BRAKE MOUNTS.
Any Answer Products fork found by the factory to be defective in materials and/or workmanship within one year from the date of purchase will be repaired or replaced at the
option of the manufacturer, free of charge, when received at the factory with proof of
purchase, freight prepaid. This warranty does not cover breakage, bending, or damage
that may result from crashes or falls. This warranty does not cover any fork that has
been subject to misuse or whose serial number has been altered, defaced or removed.
This warranty does not cover paint damage. Any modifications made by the user will
render the warranty null and void. This warranty is expressly in lieu of all other warranties, and any implied are limited in duration to the same duration as the expressed
warranty herein. Answer Products shall not be liable for any incidental or consequential
damages.
This SX fork is fully assembled and ready to be installed onto your bicycle. It comes
equipped with a 1 1/8-inch threadless steerer tube, and is available with a V-brake-style
hangerless arch.
If for any reason warranty work is necessary, return the fork to the place of purchase. In
the USA, dealers should call Answer Products for a return authorization number (RA#)
at (661) 257-4411. At that time, instructions for repair, return, or replacement shall be
given. Customers in countries other than USA should contact their dealer or local distributor.
2001 SX FORK LINE
SX E...................80MM TRAVEL/COIL-MCU SPRING/TPC PLUS DAMPING/
SINGLE CROWN
SX/SX 100MM ...80MM/100MM TRAVEL/TPC SPORT DAMPING/SINGLE CROWN
SX R ..................80MM TRAVEL/TPC DAMPING/SINGLE CROWN
One last note. If you lose this manual, or want to take a look at the SX Service Manual
or MRD Tuning Manual, head straight for the web at www.answerproducts.com or call
(661) 257-4411 and ask for warranty service.
BICYCLING IS A HAZARDOUS ACTIVITY THAT
REQUIRES THAT THE RIDER STAY IN CONTROL OF HIS OR HER BICYCLE AT ALL TIMES. READING THIS MANUAL ENTIRELY, AND
PROPERLY MAINTAINING YOUR BICYCLE AND SUSPENSION FORK AND REAR SHOCK,
WILL REDUCE THE POSSIBILITY OF INJURY OR POSSIBLE DEATH. PRIOR TO RIDING
YOUR BICYCLE, YOU SHOULD INSPECT YOUR SUSPENSION FORK TO ENSURE THAT NO
DAMAGE HAS OCCURRED DURING THE COURSE OF RIDING. DO NOT RIDE YOUR BICYCLE IF THE FORK OR SHOCK SHOWS ANY SIGNS OF BENDING, CRACKING, LEAKING, OR
IF IT IS MISSING ANY OF THE ORIGINALLY SUPPLIED COMPONENTS. ANY FALL FROM
YOUR BICYCLE CAN RESULT IN SERIOUS INJURY OR EVEN DEATH. FOLLOWING THESE
INSTRUCTIONS CAN HELP YOU REDUCE THE RISK OF BEING INJURED.
IF YOU ARE A MODERATE OR AGGRESSIVE OFF-ROAD RIDER, OR RIDE AT LEAST THREE
TIMES A WEEK OVER ROUGH TERRAIN, ANSWER RECOMMENDS RETURNING YOUR SUSPENSION FORK EVERY 2 YEARS FOR A THOROUGH INSPECTION AND UPDATE. TAKE
YOUR FORK TO A MANITOU AUTHORIZED DEALER WHO CAN ARRANGE FOR SHIPMENT
TO ANSWER PRODUCTS, OR YOU MAY CALL ANSWER TO HAVE YOUR FORK SHIPPED
DIRECTLY AT (661) 257-4411.
IMPORTANT: The SX fork is an off-road fork, and as such, does not come with
proper reflectors for on road use. Have your dealer or mechanic install proper reflectors to meet the Consumer Product Safety Commission’s (C.P.S.C.) Requirements for
Bicycles if the fork is going to be used on public roads at any time. If you have questions regarding C.P.S.C. Standards or would like to purchase a reflector bracket kit
(Part Number 85-3674) contact your dealer.
CONSUMER SAFETY INFORMATION
1. Never remove or have the steerer tube or stanchions removed from the crown. The
steerer tube and stanchions (inner legs) are press fit at the factory. Press fit inner
legs have higher performance versus bolt-in inner legs, but can not be pressed
out. Pressing them out will permanently damage the crown beyond repair and render it unsafe for any continued use.
2. Never attempt to thread a threadless steerer tube. Cutting threads will weaken the
steerer tube and cause an unsafe condition. The only safe thing to do is to obtain
the proper crown/steerer from your dealer, or contact Answer warranty at (661)
257-4411.
3. Any other alteration or modification to your fork should be considered unsafe.
Contact Answer Technical Support prior to modifying your fork in any way for safety information.
4. Do not use the SX fork if any parts are broken, bent, cracked, or you suspect may
be damaged. Contact your dealer or Answer Products Technical Support at (661)
257-4411 if you have any questions concerning the integrity or condition of your
fork.
5. Answer Products recommends that you periodically inspect your fork for wear and
damage. Inspect the crown, inner legs, outer legs dropout and brake arch areas for
cracks or damage.
INSTALLATION INSTRUCTIONS
Ensure that the proper steerer tube has been delivered on your SX first. The steerer tube
may need to be cut to length to fit your bicycle head tube. If you are not familiar with
this procedure, or do not have the proper tools to cut the steerer tube, it is recommended that you seek a dealer with a qualified bicycle mechanic to perform installation.
THE STEERER TUBE AND STANCHIONS (INNER LEGS) ARE A
ONE-TIME PRECISION PRESS FIT AT THE FACTORY AND CANNOT BE REMOVED FROM THE CROWN. REPLACEMENT OF THE ENTIRE CROWN/STEERER ASSEMBLY MUST BE DONE TO CHANGE STEERER TUBE LENGTHS OR DIAMETERS.
REMOVING AND REPLACING THE STEERER TUBE OR STANCHIONS WILL RESULT IN AN
UNSAFE CONDITION AND SHOULD NEVER BE DONE.
FORK INSTALLATION
1. Remove the old fork from your bicycle.
2. Measure and cut the steerer tube to fit your bicycle head tube. You can use your
old fork as a guide to how long you should cut the steerer tube to.
3. Remove the headset crown race from the old fork and press onto the SX steerer
until the race is seated over the crown (Figure 1).
4. Clean and grease the headset bearings and races.
5. Install the lower bearings (if applicable) on fork crown race.
6. Insert the steerer tube into the head tube of the frame.
7. Install the upper bearings, stem spacers, and stem.
8. Install the stem cap and bolt. Tighten the bolt to headset manufacturer’s specifications.
9. Install the handlebars to desired height and the torque stem pinch screws or stem
clamping system to manufacturer’s specifications.
10. Install the brakes and adjust per the manufacturer’s instructions.
11. For all SX’s adjust the front wheel quick release to clear the 0.275 (7 mm) thick
secondary catch dropout. The quick release must be tightened after it is properly
seated into the dropout counter bores to manufacturer’s specifications. Insure that
there is adequate thread engagement (4 or more threads with the release adjusted
to lock.
12. Install the brake cable per manufacturer’s instructions.
NOTE: 2001 SX E, SX, SX 100MM, and SX R forks are equipped with a secondary catch
dropout to retain the wheel in the fork in the event the quick release comes loose.
WHEN INSTALLING THE WHEEL OR A NEW TIRE, CHECK TO
MAKE SURE THE FORK ACHIEVES MINIMUM TIRE CLEARANCE. MEASURE FROM THE HIGHEST POINT ON THE TIRE TO THE BOTTOM OF THE
CROWN. THE MINIMUM CLEARANCE ALLOWED IS:
3.26" (83MM) FOR 80MM TRAVEL FORKS
4.05" (103MM) FOR 100 MM TRAVEL FORKS
ANY CLEARANCE LESS THAN THIS CAN RESULT IN SERIOUS INJURY OR DEATH. FIGURE
2
IMPORTANT: The SX should not be used if any parts appear to be or are damaged. Contact your local dealer or Answer Products for replacement parts.
MAINTENANCE
IMPORTANT: Use of fork boots is required to keep your SX fork performing well
and the warranty in effect. Use of this fork without boots will shorten the life of the
fork, decrease the time between maintenance intervals, reduce the performance and
void the warranty. The only exception is a fork that is sold by Answer from the factory without boots.
Your SX fork requires periodic maintenance, cleaning and inspection. This is because
moisture and contamination may build up inside the fork depending on the severity of
riding conditions. To maintain top performance, it is recommended that the fork be periodically disassembled, cleaned, dried and re-greased using the Microlube grease ports
located on the back of each outer leg (Figure 3). For information on how to properly
service your fork, you will need the 2001 SX Service Manual P/N: 85-3692.
IMPORTANT: When lubricating the fork with grease through the grease ports, it is
important to note the grease is being forced between the upper and lower bushings.
If the area is overfilled the force of the grease may force the upper bushing and dust
seal out. You should only insert grease to the level at which stiction is no longer felt.
IMPORTANT: Before every ride you should:
1. Ensure that quick release skewers are properly adjusted and tight.
2. Wipe the inner legs and clean and check entire fork for any obvious damage.
3. Check the headset for proper adjustment.
4. Ensure that the front brake cable is properly routed and check brake adjustment.
CHECKING OIL LEVEL
IMPORTANT: Maintaining the proper oil level in your TPC-equipped fork is criti-
cal. TPC is located in the right leg of your SX, SX 100MM and SX R forks. Not
enough oil will allow foaming and reduce the performance. Too much oil will restrict
travel and may cause damage to the system and create an unsafe riding condition.
Finish reading this entire section prior to altering the oil level.
To check the oil level, remove the compression assembly located in the top of the right
leg. Leave the left side spring stack in place to keep the fork fully extended. Use a tape
measure or “dip stick” to determine the oil level. The oil level should be per the following table. (See Figure 4.)
OIL LEVEL
Fork Model
SX E
Maximum
——
Minimum
——
Recommended
——
SX / SX 100MM
3.75" (95 mm)
4.75" (121 mm)
4.25" (108 mm)
SX R
3.75" (95 mm)
4.75" (121 mm)
4.25" (108 mm)
NOTE: Use Maxima SAE 5WT suspension fluid only.
ADJUSTING SPRING RATE
SX forks offer a wide adjustment range to suit individual riding preference and rider
weight by simply changing the MCU and coil springs in the fork. Fine tuning of the
spring rate can be made by rotating the adjuster knobs located on top of the left fork
leg. Rotating the knob clockwise will firm the ride and add preload to the spring stack.
Rotating the knob counter clockwise will soften the ride and decrease preload on the
spring stack. Four full revolutions will take the adjuster from full soft to the firmest setting.
SPRING RATE FINE TUNING: Figure 5
RECOMMENDED SPRING RATE FOR 2001 SX R FORK
Rider Weight
Coil Spring
MCU Spring
100-125 lbs.
(1) 5.8" 80 pound coil
(1) 2" green or 2" blue MCU
125-150 lbs.
(1) 5.8" 110 pound coil
(1) 2" green or 2" blue MCU
150-170 lbs.
(1) 5.8" 110 pound coil
(1) 2" blue MCU
170-190 lbs.
(1) 5.8" 110 pound coil
(1) 2" red or 2" yellow MCU
190+ lbs.
(1) 5.8" 140 pound coil
(1) 2" red or 2" yellow MCU
RECOMMENDED SPRING RATE FOR 2001 SX FORK
Rider Weight
Coil Spring
MCU Spring
100-125 lbs.
(1) 3.5" 190 pound coil
(3) 2" blue and (1) 1" blue MCU
125-150 lbs.
(1) 3.5" 190 pound coil
(2) 2" blue, (1) 2" red and
(1) 1" red MCU
150-170 lbs.
(1) 3.5" 190 pound coil
(3) 2" red and (1) 1" red MCU
170-190 lbs.
(1) 3.5" 190 pound coil
(2) 2" yellow, (1) 2" red and
(1) 1" red MCU
190+ lbs.
(1) 3.5" 190 pound coil
(3) 2" yellow and (1) 1" yellow MCU
RECOMMENDED SPRING RATE FOR 2001 SX 100MM FORK
Rider Weight
Coil Spring
MCU Spring
100-125 lbs.
(1) 5.8" 80 pound coil
(1) 2" blue and (1) 1.5" red MCU
125-150 lbs.
(1) 5.8" 110 pound coil
(1) 2" red and (1) 1.5" blue MCU
150-170 lbs.
(1) 5.8" 110 pound coil
(1) 2" yellow and (1) 1.5" red MCU
170-190 lbs.
(1) 5.8" 140 pound coil
(1) 2" red and (1) 1.5" yellow MCU
190+ lbs.
(1) 5.8" 140 pound coil
(1) 2" yellow and (1) 1.5" yellow MCU
NOTE: MCU’s and springs used in pre-2000 model Manitou forks are NOT interchangeable with later versions of Manitou forks. Recommended spring kits are available
through your dealer.
ADJUSTING DAMPING
SX R COMPRESSION DAMPING FINE TUNING: Figure 6
To adjust the compression damping on your SX R fork, simply rotate the compression
damping knob located on top of the right leg. Rotating the knob clockwise (while looking at the fork from the bottom) will increase damping, while rotating the knob counterclockwise will reduce damping. Excessive damping (or an overly stiff spring rate) will
give you a harsh ride over sharp bumps like rocky sections, but will handle large hits
like G-outs well. Insufficient compression damping (or an overly soft spring rate) will
cause the fork to bottom out on large hit G-outs and bob a little while climbing, but feel
plush on the sharp hits. A correctly adjusted fork will perform well in all conditions.
REBOUND DAMPING FINE TUNING: Figure 7
To adjust the rebound damping on your SX R fork, simply rotate the rebound damping
knob located on the bottom of the right leg. Rotating the knob clockwise will increase
the damping, while rotating the knob counterclockwise will reduce the damping.
Excessive damping (or an overly soft spring rate) will give you a harsh ride over repetitive bumps (like braking bumps) because the fork will pack up and sit too deep in the
travel under normal riding conditions. Insufficient rebound damping will make the fork
overly active and may even cause the fork to top out (a slight thumping noise when the
fork extends completely). We suggest that you try adjusting your fork on the very active
side, with minimum rebound damping. Then try it over a variety of terrain and tune in
more rebound from there.
TUNING TPC SPORT
TPC Sport is not adjustable externally, but that doesn’t mean you can’t vary the feel of
the fork; changing the fork oil weight in your TPC Sport-equipped fork will significantly
alter the damping character of the fork. The standard fork fluid for Manitou forks is 5weight Maxima, but 2.5-weight oil will decrease damping control, while 7.5-weight will
increase damping control in the TPC Sport system.
One thing to remember when changing standard fork fluid is that the increased or
decreased oil weight will affect both compression and rebound damping equally. This
means that while you may be slowing rebound down by say, adding heavier fork oil, you
also may be adding compression damping to the point of the fork feeling harsh. The
best thing to do is to experiment with different oil weights until you find that perfect setting for you.
NOTE: Since TPC Sport uses orifices (or holes) in the compression and rebound pistons
to meter the flow of oil (and thus create damping), changing the orifice sizing may
seem an obvious method to tuning TPC Sport. While doing this will produce significant
changes in the damping of the fork, it is not recommended. Changing the size of the
damping ports risks damaging the pistons, will void the warranty on the fork and will
most likely compromise the performance of the fork as well.
Figures 8, 9, 10 & 11 are schematics of the SX E, SX, SX 100MM & SX R. n
BUSHING & SEAL DETAIL
2001 SX FORK SCHEMATIC
COMPRESSION DAMPING
ASSEMBLY (062496)
CAP 0-RING (040524)
FORK BOOT (041244)
TOP CAP (062507)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
REBOUND PISTON (062297)
UPPER SEAL (062972)
LOWER SHAFT
ASSEMBLY (063106)
COMPRESSION VALVE (062296)
PISTON O-RING (040681)
SHIM .377 X .900 (062300)
UPPER BUSHING (041473)
SHAFT (062994)
LOWER BUSHING (041474)
SPIROLOX RETAINER (062393)
LOC-OUT ROD SEAL (062392)
CROWN/STEERER
END CAP (062422)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
BOTTOM OUT ELASTOMER (063116)
INNER LEG
BOTTOM OUT WASHER (063181)
RETAINING RING (040679)
O-RING 3/4" x 7/8" (040681)
DAMPER DROPOUT SLEEVE (041574)
END CAP (062249)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
INNER LEG
BOTTOM OUT ELASTOMER (063116)
BRAKE POST 9MM HEX (041927)
(TORQUE 90-110 INCH-LBS)
(TORQUE 10-12 N-M)
ADJUSTER ASSEMBLY (062529)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
BOTTOM CLIP (040968)
BLUE MCU (041424)
SPRING CONNECTOR (041377)
110LB STEEL SPRING
5 7/8" LONG (041890)
COMPRESSION ROD (063109)
DAMPER DROPOUT
NUT (041823)
OUTER CASTING
COMPRESSION ROD SCREW (060268)
(TORQUE 10-30 INCH-LBS)
(TORQUE 1.2-3.5 N-m)
REBOUND ELASTOMER (041475)
BUSHING & SEAL DETAIL
2001 SX 100MM FORK SCHEMATIC
COMPRESSION DAMPING
ASSEMBLY (062496)
CAP 0-RING (040524)
FORK BOOT (062251)
TOP CAP (062507)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
LOWER SHAFT
ASSEMBLY (063251)
REBOUND PISTON (062297)
UPPER SEAL (062972)
COMPRESSION VALVE (062296)
PISTON O-RING (040681)
SHIM .377 X .900 (062300)
UPPER BUSHING (041473)
SHAFT (063752)
LOWER BUSHING (041474)
SPIROLOX RETAINER (062393)
LOC-OUT ROD SEAL (062392)
CROWN/STEERER
END CAP (062422)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
INNER LEG
BOTTOM OUT ELASTOMER (063116)
BOTTOM OUT WASHER (063181)
RETAINING RING (040679)
O-RING 3/4" x 7/8" (040681)
DAMPER DROPOUT SLEEVE (041574)
END CAP (062249)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
INNER LEG
ADJUSTER ASSEMBLY (062529)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
BOTTOM OUT ELASTOMER (063116)
BRAKE POST 9MM HEX (041927)
(TORQUE 90-110 INCH-LBS)
(TORQUE 10-12 N-M)
BOTTOM CLIP (040968)
RED MCU (041428)
MCU CONNECTOR (041237)
BLUE MCU (041424)
SPRING CONNECTOR (041377)
110LB STEEL SPRING
5 7/8" LONG (041890)
COMPRESSION ROD (063250)
DAMPER DROPOUT
NUT (041823)
OUTTER CASTING
COMPRESSION ROD SCREW (060268)
(TORQUE 10-30 INCH-LBS)
(TORQUE 1.2-3.5 N-m)
REBOUND ELASTOMER (041475)
BUSHING & SEAL DETAIL
2001 SX E FORK SCHEMATIC
FORK BOOT (041244)
TOP CAP (062507)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
UPPER SEAL (062972)
COMPRESSION ROD (063250)
UPPER BUSHING (041473)
LOWER BUSHING (041474)
CROWN/STEERER
INNER LEG
END CAP (062249)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
BOTTOM OUT ELASTOMER (063116)
BOTTOM CLIP (040968)
WASHER (041828)
INNER LEG
BRAKE POST 9MM HEX (041927)
(TORQUE 90-110 INCH-LBS)
(TORQUE 10-12 N-M)
END CAP (062249)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
ADJUSTER ASSEMBLY (062529)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
RED MCU (063327)
BOTTOM OUT ELASTOMER (063116)
BOTTOM CLIP (040968)
MCU CONNECTOR (041237)
RED MCU (063327)
SPRING CONNECTOR (041377)
SPRING 4 1/4" (063162)
WASHER
(041828)
OUTTER CASTING
(2X) COMPRESSION ROD SCREW (060268)
(TORQUE 10-30 INCH-LBS)
(TORQUE 1.2-3.5 N-m)
COMPRESSION ROD (063263)
REBOUND ELASTOMER (041475)
BUSHING & SEAL DETAIL
2001 SX R FORK SCHEMATIC
FORK BOOT (041244)
COMPRESSION DAMPING
ASSEMBLY (063111)
LOWER SHAFT ASSEMBLY
(062929)
JELLY BEAN (062578)
SELF TAPPING SCREW (041330)
TPC KNOB (062503)
TPC TOP CAP (062583)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
VALVE NUT (041483)
CLAMP SHIM (041157)
REBOUND SHIM 20mm (041149)
REBOUND SHIM 21mm (041150)
PISTON (062562)
O-RING 1/4 X 3/8 (040690)
.826 X .409 X .005 SHIM (041139)
UPPER SEAL (062972)
ADJUSTER NEEDLE (062072)
O-RING 5/32 X 9/32 1/16
(041130)
DETENT SLEEVE (041527)
SPRING (041152)
UPPER BUSHING (041473)
PISTON SEAT (062130)
DETENT BALL (040689)
LOWER BUSHING (041474)
LOWER SHAFT (062970)
UPPER SHAFT (062723)
DETENT BALL
(040689)
VALVE SEAT (062130)
CLAMP SHIM 13MM (041157)
O-RING 5/32" x 9/32" (041130)
LOWER NEEDLE (062570)
0-RING 1/4 X 3/8
(040690)
COMPRESSION SHIM STACK
(041148, 041149,
2X 041150)
SPIROLOX RETAINER (062393)
WASHER .737 X .550 (062413)
LOC-OUT ROD SEAL (062392)
PISTON (062562)
SHIM (041139)
END CAP (062422)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
SPRING (041152)
VALVE NUT (041483)
O-RING 3/4 X 7/8 (040681)
BOTTOM OUT ELASTOMER (063116)
BOTTOM OUT WASHER (063181)
RETAINING RING (040679)
CROWN/STEERER
DETENT SLEEVE (041527)
INNER LEG
DAMPER DROPOUT
SLEEVE (041574)
BRAKE POST 9MM HEX (041927)
(TORQUE 90-110 INCH-LBS)
(TORQUE 10-12 N-M)
INNER LEG
END CAP (062249)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
BOTTOM OUT (063116)
ADJUSTER ASSEMBLY (062540)
(TORQUE 30-50 INCH-LBS)
(TORQUE 3.5-5.6 N-m)
BOTTOM CLIP (040968)
DAMPER DROPOUT
NUT (041822)
BLUE MCU (041424)
O-RING, DROPOUT
NUT (040688)
DAMPER ADJUSTER
KNOB (041408)
SPRING CONNECTOR (041377)
OUTTER CASTING
110LB SPRING 5 7/8" LONG (041890)
COMPRESSION ROD SCREW
(060268)
(TORQUE 10-30 INCH-LBS)
(TORQUE 1.2-3.5 N-m)
COMPRESSION ROD (063109)
REBOUND ELASTOMER (041475)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement