LESLIE 8253 Console Connector Kit, 251, 351 Speaker, A100, M100, E100 Hammond, Echo Control, Tremolo Control Installation instructions

LESLIE CONSOLE CONNECTOR KIT 8253 INSTALLA TION INSTRUCTIONS

FOR USE WITH: HAMMOND Models A100, M100, or E100

LESLIE Speaker 251 or 351

MULTIPLE SPEAKER INSTALLATION: For complete information, see the service manual of the LESLIE Speaker to be added.

Contents of Kit:

1 -Console Connector

1 -Console Adapter

1 -6 Conductor Cable

1 -Oiler

011874

062091

017277

053025

1 -Instructions

2 -Screws, 8 x 1/2

034686

029132

4 -Screws, 6 x 1/2, Blk Oxide 029124

8 -Wire Nuts 028076

2 -Connector, Tab, Male

2 -Connector, Tab, Female

5 -Insulated Staples

029371

029389

028464

1 -Tremolo Control

024976

024984

024992

1 -Echo Control

011882

011890

011908

Brown

Ebony

Ivory

Brown

Ebony

Ivory

To Install the Kit:

1. Attach the Echo and Tremolo controls to the wooden rail in front of the lower manual with the black oxide screws provided. Use the two mounting holes which best center the screws in the rail.

2. Remove the console dust cover, and pass the control cables into the console by one of the following methods:

A100, M100: Clip the red and green interceptor plugs and sockets off the Echo control cable and strip the wires 3/8". Push a small screwdriver over the felt dust seal between the lower manual and the knee panel. Push the cables through this opening into the console. From the back of the console, reach behind the tone generator and pull the cables through .

E100: Remove the knee plate under the lower manual, and pass the control cables into the console through this opening. Cut a small notch in the edge of the knee plate to accommodate the cables, then replace it.

3. Pass the switch cables through the slot in the rear edge of the shelf into the lower compartment.

4. Position the console connector near the power amplifier, so that the power and control cables will reach. Install it with the wood screws provided.

Page 1 of 4

5. A100, M100: Cut the green lead which connects the amplifier output to the main speakers. (See "A" & "B" on Fig. 1 & 2.) Remove 3/8" of insulation from each of the cut ends. Connect the amplifier end of this lead to the red lead from the Echo control with a wire nut. Connect the speaker end of the lead to the green lead from the Echo control. (See "B" on Figs. 1 & 2.)

E100: Remove the green speaker plug from the chassis socket on the left-hand apron of the power amplifier. (See "A" on Fig. 3.) Fit this plug intothe green interceptor socket onthe Echo switch cable, and fit the interceptor plug into the chassis socket.

6. A100, Ml00: a Disconnect the reverberation input lead (green on A100 and M100A; red on

M100) from the main speakers. (See "C" on Figs. 1 & 2.) Strip and connect it to the orange lead from the Echo control with the wire nut provided.

b Detach the "hot" lead (gray or blue) from the reverberation speaker terminal, strip it about 3/8", and connect it to the blue lead from the Echo control with the wire nut provided. (See "D" on Figs. 1 & 2.) c Solder the yellow Echo control lead to the "hot" reverberation speaker terminal.

(See "E" on Figs. 1 & 2.)

E100: Remove red speaker plug from the chassis socket on the left apron of the power amplifier. (See "B" on Fig. 3. ) Fit this plug into the red interceptor socket on the Echo switch cable; then connect red interceptor plug to the red chassis socket. Fold back the orange wire attached to the Echo switch. Insulate it with the plastic sleeve provided. It is not used in this installation.

7. A100: Plug the Console Connector pigtail into the 5 contact socket on the rear apron of the power amplifier chassis. (See "F" on Fig. 1.)

M100: Cut the 5 pin plug off the Console Connector pigtail and strip all three leads about 1/4". Solder the brown POT cord to the outside AC terminals under the metal cover on the left-hand side of the rear apron of the power amplifier. (See

"F" on Fig. 2.) Fasten the red lead to any convenient ground point on the amplifier chassis. (See "F" on Fig. 2.)

E100: Plug the Console Connector pigtail into the 062091 adapter and insert it into the 7 contact socket on the rear apron of the amplifier chassis. (See "C" on Fig.

3.)

8. Connect the brown lead from the Echo control to the brown lead from the Console

Connector with the wire nut provided. (See "G" on Figs. 1 & 2; "D" on Fig. 3.)

9. Connect the black lead from the Echo control to the black lead from the Console

Connector with the wire nut provided. (See "H" on Figs. 1 & 2; "E" on Fig. 3.)

Page 2 of 4

10. Connect the POT cord from the Tremolo control to the short POT cord on the

Console Connector with the wire nuts provided. (See "I" on Figs. 1 & 2; "G" on Fig.

3.)

11. Plug the speaker cable into the 6 contact socket on the Console Connector. (See

"J" on Figs. 1 & 2; "H" on Fig. 3. )

12. Adjust the speaker volume control as indicated in the manual. Set speaker load resistor to OPEN. The installation is now complete.

13. Replace the console dust cover and back.

011874 CONSOLE CONNECTOR PARTS LIST:

C1 Capacitor, Disk, .01 mf, 1000V, 20% 060467

P1 Plug, 5 Pin, w/o Plate

R1,2 Resistor, 80hm, 10W, Wire Wound

S1 Socket,6 Contact, w/Mtg Plate

013060

010934

060459

Control Switch Parts List:

Echo Control

Echo Switch Case

029199 Brown

029207 Ebony

029215 Ivory

Switch Retainer (2 req'd)

P2 Plug Hsing, Red-Amp

S2 Socket Hsing, Red-Amp

Switch Case Cover

048702 Brown

048710 Ebony

048728 Ivory

048116

016576

016568

P2 Insert, Male-Amp (2 req'd) 010421

S2 Insert, Female-Amp (2 req'd) 010397

P3 Plug Hsing, Grn-Amp

S3 Socket Hsin9, Grn-Amp

010389

010371

P3 Insert, Male-Amp (2 req'd) 010421

S3 Insert, Female-Amp (2 req'd) 010397

Switch Knob

048066 Brown

048074 Ebony

Switch Only 029173

Tremolo Control

Tremolo Switch Case

012260 Brown

012278 Ebony

012286 Ivory

Switch Retainer (2 req'd)

Switch Only

Switch Case Cover

048702 Brown

048710 Ebony

048728 Ivory

048108

042911

Switch Knob

048066 Brown

048074 Ebony

Ordering Parts:

Standard hardware, connectors, and electronic components should be purchased locally. Non-standard items may be obtained through a Leslie speaker dealer. Orders should include part numbers shown above.

Page 3 of 4

Page 4 of 4