A1 - DDCSN

A1 - DDCSN
SERIES 60 SERVICE MANUAL
1. Gear Case Cover
5. Bolt
2. Gear Case
6. Acoustical Cover
3. Acoustical Cover Snap
7. Acoustical Cover
4. Acoustical Cover Clip
8. Nut
Figure 1-179
Typical Group D Rear Acoustical Cover Installation
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-225
1.11
GEAR CASE
1.11 GEAR CASE
The gear case housing is constructed of cast iron, with machined mating surfaces, and is bolted to
the front of the engine cylinder block. The gear case and gear case cover are bolted together to
provide a sealed compartment for the engine gear train. See Figure 1-180.
1. Lifting Bracket
3. Gear Case Housing
2. Gear Case Cover
Figure 1-180
Gear Case and Gear Case Cover
Several components are mounted to the gear case, including the adjustable idler gear assembly,
see Figure 1-181, the fuel pump drive assembly, see Figure 1-182, the air compressor drive
assembly or raw water pump drive assembly, see Figure 1-183; the water pump assembly (1991
and later engines) see Figure 1-184; and the camshaft thrust plate and drive gear assembly
see Figure 1-199.
(Rev. 07/01)
1-226
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
In July 2001, new right and left side gear case stiffening brackets were added to provide: reduce
engine noise, increase belt driven accessory life, reduce gear case vibration amplitude and reduce
wear on the cam thrust plate perimeter seal. See Figure 1-180A and see Figure 1-180B
Figure 1-180A
Gear Case Stiffening Bracket (Left Side)
Figure 1-180B
Gear Case Stiffening Bracket (Right Side)
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-226a
1.11
GEAR CASE
This page intentionally left blank.
(Rev. 07/01)
1-226b
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
1. Gear Case
5. Adjustable Idler Gear
2. Diamond Dowel
6. Adjustable Idler Hub
3. Adjustable Idler Gear Locknut (3)
7. Adjustable Idler Gear Stud (3)
4. Adjustable Idler Gear Hub, Retainer
8. Round Dowel
Figure 1-181
Adjustable Idler Gear Assembly
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-227
1.11
GEAR CASE
1. Fuel Pump Drive Gear
5. Shaft and Bearing Assembly
2. Snap Ring
6. Fuel Pump Drive Hub
3. O-ring
7. Fuel Pump Drive Coupling
4. Fuel Pump Drive Housing
8. Fuel Pump Assembly
Figure 1-182
Fuel Pump Drive Assembly
(Rev. 07/01)
1-228
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
1. Drive Housing
8. Drive Hub Flange Nut
2. Washers
9. Drive Housing Long Bolt
3. Drive Housing Short Bolt
10. Drive Shaft
4. Drive Ball Bearing
11. Drive Gear
5. Snap Ring
12. Drive Gear Bolt
6. Spacer
13. Drive Housing Gasket
7. Drive Hub
14. Gear Case Housing
Figure 1-183
Air Compressor or Raw Water Pump Drive Assembly
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-229
1.11
GEAR CASE
1. Retaining Bolt
11. Oil Seal
2. Washer
12. Water Pump Housing O-ring
3. Water Pump Drive Gear
13. Drain Cock
4. Snap-ring
14. Water Pump Housing
5. Bearing Race
15. Water Pump Housing Pipe Plug
6. Bearing
16. Water Seal
7. Spacer Rings (2)
17. Impeller
8. Bearing
18. Water Pump Cover O-ring
9. Bearing Race
19. Water Pump Cover
10. Drive Shaft
Figure 1-184
20. Water Pump Cover Snap Ring
Water Pump Assembly
(Rev. 07/01)
1-230
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
To eliminate the possibility of oil leakage at the adjustable idler gear stud location, Detroit Diesel
recommends the following:
When rebuilding a Series 60 engine, or if the gear case is removed for any reason, the three
original adjustable idler gear studs should be removed and replaced with new studs.
Before pressing studs into the gear case, coat the shanks and underside of the stud heads with
Loctite® No. 242 Sealant. This will prevent any oil leakage around the studs during engine
operation.
The Timing Reference Sensor (TRS) is an electronic component that is bolted to the side of the
gear case on the intake (left) side of the engine just above the oil pan. See Figure 1-185.
Figure 1-185
Timing Reference Sensor (TRS)
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-231
1.11
GEAR CASE
The Synchronous Reference Sensor (SRS) is an electronic component that is bolted to the gear
case at the lower, intake (left) side of the engine. See Figure 1-186.
Figure 1-186
Synchronous Reference Sensor
(Rev. 07/01)
1-232
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
An opening is provided in the center of the gear case, for the bull gear and camshaft idler gear
assembly, which bolts directly to the engine block. See Figure 1-187.
Figure 1-187
Bull Gear and Camshaft Idler Gear Assembly
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-233
1.11
GEAR CASE
An access cover is provided at the rear of the gear case on the cooler (right) side of the engine.
This access cover provides an opening for inspection of the accessory drive assembly drive
gear. See Figure 1-188.
NOTE:
This access cover opening may be cast closed on the rear of the gear case.
Figure 1-188
Accessory Drive Gear Access Cover (Pre-1991 Engines)
(Rev. 07/01)
1-234
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
For gear lash measurement and adjustment procedures for the gears in the engine gear train,
Refer to section 1.21.2.1.
An oil gallery is drilled in the gear case casting, for lubrication of the adjustable idler gear
assembly. A hole in the front of the cylinder block, indexes with the gear case gallery. At the edge
of the gear case the gallery is threaded for insertion of a plug. An exit hole feeds the adjustable
idler gear assembly. See Figure 1-189.
NOTE:
Do not use the oil plug location for an oil supply or for checking oil pressure.
Figure 1-189
Adjustable Idler Gear Lubrication Gallery
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-235
1.11
GEAR CASE
1.11.1
Repair or Replacement of Gear Case
To determine if repair is possible or replacement is necessary, perform the following procedure.
See Figure 1-190.
Figure 1-190
Flowchart for Repair or Replacement of Gear Case
(Rev. 07/01)
1-236
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
1.11.2
Removal of Gear Case
Perform the following steps to remove the gear case:
1. Remove the SRS. Refer to section 2.29.2 .
2. Remove the TRS. Refer to section 2.30.2 .
3. Remove the rocker arm assemblies. Refer to section 1.3.2.
4. On heat exchanger-cooled marine engines, remove the water-cooled charge air cooler.
Refer to section 4.4.2 . Or remove the heat exchanger tank. Refer to section 2.13.1 .
5. Perform all of the steps for camshaft removal. Refer to section 1.23.2.
6. Remove the 3 bolts that secure the camshaft gear pilot tool, J 35906, to the gear case
and remove the tool.
7. Remove the three bolts securing the former right side gear case stiffening bracket, or two
bolts securing the current right side gear case stiffening bracket. See Figure 1-190A.
Figure 1-190A
Gear Case Stiffening Bracket (Right Side)
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-237
1.11
GEAR CASE
8. Remove the three bolts securing the left side gear case stiffing bracket. See Figure 1-190B
Figure 1-190B
Gear Case Stiffening Bracket (Left Side)
9. Remove gear case cover. Refer to section 1.10.2, for step 1 through step 13. Supporting
the gear case cover with a suitable lifting device, but don’t remove it.
10. Remove the fuel pump from the fuel pump drive assembly (or air compressor).
Refer to section 2.6.2 .
11. Remove the air compressor. Refer to section 10.1.5 .
12. Remove the air compressor drive assembly. Refer to section 10.3.2 .
(Rev. 07/01)
1-237a
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
13. Install the crankshaft protector, J 35994, to the oil seal contact area of the crankshaft. This
will help to protect the crankshaft seal surface when removing the bull gear and camshaft
idler gear assembly. See Figure 1-191.
Figure 1-191
Crankshaft Protector Installation
14. Remove the bull gear and camshaft idler gear assembly from the engine.
Refer to section 1.26.2.
15. Remove the adjustable idler gear assembly from the gear case. Refer to section 1.25.2.
16. Using a plastic hammer or fiber mallet, tap the rear face of the camshaft thrust plate to
remove the thrust plate, camshaft drive gear hub and camshaft drive gear from the gear
case.
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-237b
1.11
GEAR CASE
17. Remove the 12 bolts that secure the gear case to the engine block. See Figure 1-192
Figure 1-192
Gear Case Mounting Bolt Locations
(Rev. 07/01)
1-238
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
18. Using a leather or cloth-wrapped strap, support the gear case. See Figure 1-193.
Figure 1-193
Gear Case Removal
19. Use a rubber hammer or plastic mallet to loosen the gear case from the cylinder block
dowels.
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-239
1.11
GEAR CASE
1.11.2.1
Inspection of Gear Case
Clean all of the old gasket sealer from the mating surfaces of the gear case, gear case cover, and
engine block. Refer to "Gasket Eliminator Removal," in the "General Information" section at the
beginning of this manual. Clean the gasket material from the mating surfaces of any components
or access covers that were removed from the gear case cover or gear case. Clean all of the parts
with clean fuel oil and dry with compressed air. Remove the oil gallery plug at the edge of the
gear case. See Figure 1-189.
To avoid injury from flying debris when using compressed
air, wear adequate eye protection (face shield or safety
goggles) and do not exceed 40 psi (276 kPa) air pressure.
Use compressed air to ensure the oil gallery is completely free of blockage. If necessary, use a
wire brush to clean the gear case oil gallery.
Inspect the gear case for stress cracks, breaks, or other damage. Repair or replace as necessary.
Inspect the adjustable idler gear studs for signs of galling or scoring. Replace as necessary.
Inspect all the individual components as outlined under the appropriate section.
(Rev. 07/01)
1-240
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
1.11.3
Installation of Gear Case
Use the following instructions for gear case installation:
1. Apply a thin film of gasket eliminator PT-7276 (Loctite® 518) or equivalent to the cylinder
block. See Figure 1-194. Carefully smooth the bead around the block-to-gear case oil
passage to avoid contamination.
NOTE:
The installation of Gasket Eliminator to the gear case-to-block mating surfaces at the top
of the block is critical. Excess gasket eliminator material can extrude into the oil passage
between the block and gear case, causing early failure of components. In addition, the
bull gear recess area MUST be cleaned of any and all foreign material after installation of
the gear case to the engine block.
Figure 1-194
Gasket Eliminator Application
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-241
1.11
GEAR CASE
2. Insert gear case alignment plug, J 35651, into the bull gear and camshaft idler gear hub
recess in the cylinder block. See Figure 1-195.
Figure 1-195
Gear Case Alignment Plug
(Rev. 07/01)
1-242
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
3. Using a suitable lifting sling made of cloth or leather, position the bull gear and camshaft
idler gear opening of the gear case over the gear case alignment plug. Index the hole
in the gear case mating surface with the diamond dowel at the lower left corner of the
cylinder block. See Figure 1-196.
Figure 1-196
Cylinder Block Locating Diamond Dowel
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-243
1.11
GEAR CASE
4. With the gear case alignment plug fully seated, the gear case centered on the alignment
plug and the diamond dowel in the cylinder block indexed with its mating hole in the gear
case, the gear case is positioned properly for bolt installation. See Figure 1-197.
Figure 1-197
Gear Case Positioning
NOTE:
Gasket Eliminator cures with the absence of air. The time between the installation of
the gear case, and torquing of the bolts that secure the gear case to the cylinder block
should be kept to a minimum.
(Rev. 07/01)
1-244
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
5. Install the 12 gear case-to-cylinder block retaining bolts, finger-tight.
6. Torque the gear case-to-cylinder block bolts to 58-73 N·m (43-54 lb·ft). See Figure 1-198.
Figure 1-198
Gear Case Housing Bolt Torque Sequence
7. Remove the gear case alignment plug from the gear case.
8. Install the air compressor. Refer to section 10.1.8 .
9. Install the air compressor drive assembly. Refer to section 10.3.6 .
10. Install the fuel pump drive assembly to the gear case, if so equipped. Refer to section 2.6.5
or refer to section 2.6.6 .
11. Install the fuel pump to the fuel pump drive assembly (or air compressor).
Refer to section 2.7.3 .
NOTE:
For 1991 and later model year engines, refer to section 4.2.8 or refer to section 4.3.7 and
install the water pump assembly.
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-245
1.11
GEAR CASE
12. Lubricate the rubber O-ring on the camshaft thrust plate with clean engine oil. Install the
camshaft thrust plate assembly, with the camshaft drive gear and hub in place to the gear
case, using a plastic hammer or fiber mallet to tap the thrust plate rearward in the gear case
just enough to start it in the gear case. See Figure 1-199.
Figure 1-199
Camshaft Thrust Plate Installation
(Rev. 07/01)
1-246
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
13. Install the adjustable idler gear assembly to the gear case. Refer to section 1.25.3. Align
the timing marks of the adjustable idler gear and camshaft drive gear. See Figure 1-200.
1. Camshaft Idler Gear
4. Bull Gear
2. Adjustable Idler Gear
5. Crankshaft Timing Gear
3. Camshaft Drive Gear
Figure 1-200
Engine Gear Train Timing Marks
14. Inspect the bull gear and camshaft idler gear access opening in the gear case and remove
any foreign material.
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-247
1.11
GEAR CASE
15. Install two bull gear guide studs, J 35785 to the cylinder block. See Figure 1-201.
Figure 1-201
Bull Gear Guide Stud Installation
NOTICE:
Always install crankshaft protector when installing the bull gear
and camshaft idler gear assembly to prevent damaging the
crankshaft oil seal contact surface.
16. Install the crankshaft protector, J 35994 to the oil seal contact area of the crankshaft. This
will help to protect the crankshaft seal surface when installing the bull gear and camshaft
idler gear assembly.
17. Install the bull gear and camshaft idler gear assembly to the guide studs. Align the timing
marks on the bull gear and the crankshaft timing gear and the camshaft idler gear and
adjustable idler gear; see Figure 1-200, and slide the bull gear and camshaft idler gear
assembly forward to seat it in the recess in the gear case and cylinder block.
18. Working through the lightening holes in the bull gear, install two of the bull gear assembly
mounting bolts through the hub and into the cylinder block. Finger-tighten the bolts.
19. Remove the two bull gear guide studs. Install the remaining two bull gear assembly
mounting bolts. Torque the bolts to 101-126 N·m (75-93 lb·ft). Tighten in a clockwise
sequence.
20. Check the timing marks on the gears to ensure the gear train is properly timed.
See Figure 1-200.
(Rev. 07/01)
1-248
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
21. Perform the following:
[a] For crankshaft timing gear-to-oil pump gear lash measurement. Perform step 2,
refer to section 1.21.2.1.
[b]
For crankshaft timing gear-to bull gear lash measurement. Perform step 3,
refer to section 1.21.2.1.
[c] To install the gear case cover. Refer to section 1.10.3.
[d]
Install the two bolts and nuts securing the left side gear case stiffening bracket to the
gear case. Torque to 75–81 N·m (55–60) lb·ft). See Figure 1-201a
Figure 1-201a
Gear Case Stiffening Bracket (Left Side)
[e] Install the bolt securing the left side gear case stiffening bracket to the cylinder head.
Torque to 58–73 N·m (43–54 lb·ft). See Figure 1-201a
[f]
Install the bolt securing the right side gear case stiffening bracket to the gear case.
Torque the former bracket bolt to 58–73 N·m (43–54 lb·ft) or torque the current gear
case bracket bolt to 74–81 N·m (53–60 lb·ft). See Figure 1-201b
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-249
1.11
GEAR CASE
NOTE:
Bolts attaching bracket to the gear case are torqued first, then the bolt to cylinder head is
torqued next.
[g]
Install the two bolts securing the former right side gear case stiffening bracket to the
cylinder head or one bolt securing the current right side bracket. Torque the former
bracket bolts to 58–73 N·m (43–54 lb·ft) or torque the current gear case bracket bolt
to 74–81 N·m (53–60 lb·ft). See Figure 1-201b
Figure 1-201b
Gear Case Stiffening Bracket (Right Side)
22. Refer to section 1.23.5, "Installation of Camshaft Bearing" and perform the necessary
steps.
23. For bull gear-to-accessory drive gear lash measurement, perform
step 10 Refer to section 1.21.2.1.
24. Continue engine assembly.
(Rev. 07/01)
1-249a
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
This page intentionally left blank.
All information subject to change without notice.
(Rev. 07/01)
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
From Bulletin 10-60-01
1-249b
1.12
CRANKSHAFT VIBRATION DAMPER
1.12 CRANKSHAFT VIBRATION DAMPER
A viscous type vibration damper is mounted on the front end of the crankshaft to reduce torsional
vibrations to a safe value. See Figure 1-202.
Figure 1-202
Viscous Vibration Damper Mounting with Crankshaft Pulley or
Crankshaft Pulley and Hub Assembly with Spindle
Prior to April 1993, 11.1 liter engines with less than 320 hp (238 kW) were equipped with a 313.4
mm (12.34 in.) damper and 11.1 liter engines with 320 hp (238 kW) or more were equipped
with a 342.9 mm (13.5 in.) damper, and all 12.7 liter engines, were equipped with a 342.9 mm
(13.5 in.) damper.
Beginning in April 1993, all Series 60 engines are built with a 342.9 mm (13.5 in.) damper.
(Rev. 07/01)
1-250
From Bulletin 10-60-01
All information subject to change without notice.
6SE483 0010 Copyright © 2001 DETROIT DIESEL CORPORATION
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement