AirCraft , AirGuard , AirPro & QuietDry Dryer Guide

AirCraft

®

,

AirGuard

®

, AirPro

®

& QuietDry

™

Dryer Guide

Effective 08/13

All Bobrick dryers require cleaning every 6 months to ensure that they function effectively. Please note that failing to clean the dryer may result in malfunction and can void the warranty.

(Refer to page 3 of the Dryer Troubleshooting and Information Guide for Routine Maintenance Instructions) www.bobrick.com

U.S. Headquarters: BOBRICK WASHROOM EQUIPMENT, INC.

11611 Hart Street, North Hollywood, California 91605-5882, Tel: 818.982.9600, FAX: 818.503.1102

Email: [email protected]

Canada Headquarters: BOBRICK WASHROOM EQUIPMENT COMPANY.

45 Rolark Drive, Scarborough, Ontario M1R 3B1, Eastern: 877.423.6555, FAX: 877.423.8555, Western: 877.423.6444,

FAX: 877.423.8444, Email: [email protected]

International Sales: BOBRICK WASHROOM EQUIPMENT, INC.

11611 Hart Street, North Hollywood, CA 91605-5882, +1.818.764.1000, FAX: +1.818.503.9941


Australia: Bobrick Washroom Equipment Pty Ltd., 1.800.353158, FAX: 1.800.221926


Germany: 0800.79.00.456, FAX: 0800.79.00.789 Email: [email protected]

United Kingdom: Bobrick Washroom Equipment Ltd., +44.0.20.8366 1771, FAX: +44.0.20.8363.5794.


AirCraft_DTG r8-13 Page 1 of 28

AirCraft

®

, AirGuard

®

, AirPro

®

& Fast Dry Dryers

Contents

1.

Cover removal

Page

5

2.

Diagnostic Sheet

6

3.

Field Replacement Parts

4.

Installation Instructions

5.

Product Identification

6.

Schematic Diagrams

7.

Screwdriver Test

8.

Warranty

26

8

25

9

12

3


AirCraft

®

Dryers

Product Identification

Surface-Mounted Dryers:

B-700 Automatic Hand & Face (pictured)

B-701 Touch Button Hand & Face

B-731 Touch Button Hair

Recessed Dryers:

B-750 Automatic Hand & Face (pictured)

B-751 Touch Button Hand & Face

B-781 Touch Button Hair


AirGuard

®

Dryer

B-708 Automatic

Series Variations:

Series G lower profile cover, no nameplate or printing. (pictured)

Not all replacement parts are interchangeable, see parts list .

AirPro

®

Dryer

B-709 Touch Button

B-709 Automatic (pictured)

Series Variations:

Series A touch button model, metal nameplate.

Series B automatic model, metal nameplate.

Series C automatic model, lower profile cover, no nameplate.

Not all replacement parts are interchangeable, see parts list .

QuietDry Dryer

B-770 White cover

B-778 Chrome cover


Instructions For Removal Of Dryer Cover

Warning

Risk of electric shock

Disconnect power supply before removing cover

To Remove Cover

Locate the two tamper resistant screws at the bottom of the dryer cover.

Using the Allen-wrench (4 or 5mm), turn the screws clockwise to loosen the cover. Do not take the screws out, the screws have to be done up to loosen the cover.

Lifting the cover over the two latches at the top of the chassis, remove the cover.

To Replace Cover

Place the cover over the two latches located at the top of the chassis. Make sure that the cover has a good fit.

Using the Allen-wrench, turn the screws counter clockwise loosening the screws which will tighten the cover onto the chassis. Do not over tighten screws.

Check to make sure the cover has a good fit. Turn power back on to the dryer unit.


Diagnostic Sheet For AirCraft

®

, AirGuard

®

, AirPro

®

& QuietDry™ Dryers.

Problem

AUTOMATIC

1. Dryer does not run

Possible Cause

a) No electricity supply b) Installation fault c) Worn motor brushes d) Element open circuit e) Control nonstart f) Triac open circuit

2. Sparks from dryer Worn motor brushes

3. Dryer runs at low speed a) Worn motor brushes b) Triac halfwave c) Control halfwave

4. Dryer runs continuously a) Triac short circuit b) Control faulty

5. Dryer cycles on and off

6. Dryer sometimes runs

7. Dryer is oversensitive

Control

Dirty control lens

Control

Control

Heating element 8. Dryer blows cold air or motor runs fast

9. Grinding noise from dryer a) Worn motor brushes b) Fan cage is bent or

10. Dryer does not run and heating element glows damaged

Worn motor brushes

Possible Solution

Check main supply / wiring

Check service manual for possible wiring mistakes

Check length of brushes; replace if less than ½”

Return dryer to Bobrick for repair

Replace control

Replace triac

Replace motor brushes


Remove white wire from triac; no difference, replace triac

Remove white wire from triac; dryer stops, replace control

Remove white wire from triac; no difference, replace triac

Remove white wire from triac; dryer stops, replace control

Replace control

Clean control lens

Replace control

Replace control

Return dryer to Bobrick for repairs


Return dryer to Bobrick for repairs

TOUCHBUTTON

1. Dryer does not run

2. Sparks from dryer

3. Dryer does not run and heating element glows

4. Dryer runs at low speed a) No electricity supply b) Installation fault c) Tabs are not connecting d) Worn motor brushes e) Element open circuit f) Timer assembly nonstart

Worn motor brushes

Worn motor brushes a) Worn motor brushes

Replace motor brushes; if still not functioning after replacing the motor brushes, return dryer to Bobrick for repairs.

Check main supply / wiring

Check service manual for possible wiring mistakes

Turn off power, remove cover and bend tabs closer to sensor board

Check length of brushes; replace if less than ½”


Perform Screwdriver Test (see test instructions)


Replace motor brushes; if still not functioning after replacing the motor brushes, return dryer to Bobrick for repairs.



Problem

5. Dryer runs continuously

6. Dryer blows cold air

7. Grinding noise from dryer

Possible Cause

b) Timer assembly b) Timer assembly

Heating element a) Worn motor brushes

8. Dryer is oversensitive and switches on or off randomly b) Fan cage is bent or damaged a) Button loose

9. Dryer cycles on and off b) Timer assembly or crystal board

Timer assembly or crystal board

Possible Solution

Replace timer assembly

Replace timer assembly




Pack button O ring with tape




Screwdriver Test for Touch Button Dryers

Warning



NOTE: This test instruction sheet is not for dissemination to, and should not be disseminated to, the public including end users.

This test is designed to test the Touch Timer Assembly and the Sensor Board.

Instructions For Test:

1. Turn off the power to dryer.

2. Remove dryer cover.

3. Turn on the power. Do not touch any part of the dryer.

4. Using an insulated screwdriver, short across the two tabs (see below). a) If dryer runs ...................sensor board may be faulty ......... replace sensor board. b) If dryer does not run ......timer may be faulty ...................... replace touch controller.

5. Turn off power to dryer.

6. Put dryer cover back on and turn power on.


Field Replacement Parts

• Replacement parts are intended to be issued by Bobrick after completion of diagnostic sheets and a problem is identified that involves replacement of parts.

• Replacement parts will then be sold to the customer/rep with credit issued upon the return of identifiable malfunctioning and/or unused parts.

• A copy of the Dryer Service Information Sheet must be completed by the rep and sent to Bobrick prior to return of parts.

• Dryer voltage must be identified in order to replace parts. Replacement parts have options for both the 115V and 208–240V dryers. Check voltage and then designate correct part(s).

AirCraft ® Dryer Replacement Parts

AirGuard ® , AirPro ® & QuietDry Dryer Replacement Parts


AirCraft

®

Dryer Replacement Parts

Surface touch Surface automatic Recessed touch Recessed automatic

115V 208-240V 115V 208-240V 115V 208-240V 115V 208-240V

Touch controller

hand & face

Touch controller

hair

Sensor Board

Automatic

controller

701-360

731-360

701-138

701-361

731-361

701-138

700-360 700-361

701-360

731-360

701-138

701-361

731-361

701-138

750-360 750-361

Air Outlet Grille

& Seal

701-120 701-120 700-120 700-120 701-120 701-120 700-120 700-120

Covers Model code without the B followed by -150, voltage and then color code.

Voltage:

Color codes:

115V

230V

Almond

Black

Grey

Ivory

White

Eg. 7007-150 115V #828

Model B7007, voltage 115V, color Black.

#885

#828

#889

#848 no code

Common Parts

Triac

Motor Brushes EMD (Red Retainer)

700-325

700-101

Motor Brushes Sintech (Brass Retainer) 700-111

Motor Brushes Ametek & Winston 700-121

Cover Mounting Screws

Allen Wrench

700-156

700-55

700-506 Wall Box (Recessed Dryers Only)

Brush identification

The following items are not to be field replaced:

Motor/fan units.

Heating elements.

AirCraft_DTG r8-13 Page 10 of

28

AirGuard

®

, AirPro

®

& QuietDry™ Dryer

Replacement Parts

115V 208-240V

Touch controller 701-360 701-361

Sensor Board

Automatic controller

Air Outlet Grille & Seal

B-708 Series A – F cover

B-708 Series G cover

B-709 Series A cover

701-138

700-360

701-120

708-150 115V

708G-150 115V

709-150 115V

701-138

700-361

701-120

708-150 230V

708G-150 230V

709-150 230V

B-709 Series B cover

B-709 Series C cover

709B-150 115V 709B-150 230V

709C-150 115V

770-150 115V

709C-150 230V

770-150 230V B-770 White cover

B-778 Chrome cover 778-150 115V 778-150 230V

QuietDry Controller

Product Identification

Common Parts

770-360 770-361

Triac

Motor Brushes EMD (Red Retainer)

700-325

700-101

Motor Brushes Sintech (Brass Retainer) 700-111

Motor Brushes Ametek & Winston

Cover Mounting Screws

700-121

700-156

700-55 Allen Wrench

Brush identification

The following items are not to be field replaced:

Motor/fan units.

Heating elements.


28

Installation Instructions

Installation Instructions

Cover Replacement

Installation Of Touch Controller

Installation Of Base Plate Mounted Triac

Installation Of Automatic Controller

Instructions For Installation Of Sensor Board

Instructions For The Replacement Of Motor Brushes

Installation of Surface-Mounted Hand and Hair Dryers

Installation of Recessed AirCraft

®

Hand and Hair Dryers

Page

13

14

15

16

17

18

19

22


28

Warning


Fig 1


Cover Replacement

The dryer covers for different models are NOT interchangeable.

Fig 2

Fig 1A Fig 1B Fig 2

Fig 2A

To Remove Cover

1. Disconnect the power supply.

2. Locate the two tamper resistant screws at the bottom of the dryer cover.

3. Using the Allen-wrench (4 or 5mm), turn the screws clockwise to loosen the cover.

4. Lifting the cover over the two latches at the top of the chassis, remove the cover.

To Replace Cover

1. Place the cover over the two latches located at the top of the chassis. Make sure that the cover has a good fit.

2. Using the Allen-wrench, turn the screws counter clockwise loosening the screws; this will tighten the cover onto the chassis. Do not over tighten the screws.

3. Check to make sure the cover has a good fit. Turn the power supply back on.

4. Allow 10 seconds for the controller to stabilize and check operation of the dryer. On

Automatic Dryers if the operation is intermittent check that the controller has a clear view out of the cover aperture, use the spacers provided to raise the controller if required.


28

Installation Of Touch Controller

To Remove Existing Timer

1. Disconnect the power supply and remove the cover.

2. Remove the timer from the base plate by unscrewing the two screws securing the timer bracket to the base. On recessed dryers the timer bracket is secured to a metal angle bracket, this bracket with its screws must be removed and retained for use on the replacement timer.

3. Disconnect the pink or yellow, red, and black timer wires from the terminal block and the white wire push on connector from the triac (115V only). Place the timer aside for return to the Service

Department.

To Install New Timer

1. Mount the timer assembly to the base plate . In the case of recessed dryers, it is first necessary to attach the metal angle bracket removed from the faulty timer to the new timer.

2. Route the timer wiring under the element tube and attach the white wire push on connector to the small spade terminal on the triac (115V only), older 208 – 240V units may have a base plate mounted triac, this is no longer required and can be removed.

3. Connect the remaining three timer wires to the terminal block, black wire to terminal 1, red wire to terminal 2, pink wire to terminal 3.

4. Secure wiring with cable ties provided.

5. Replace dryer cover. Switch on electrical supply and test operation.

Warning




28

Installation Of Base Plate Mounted Triac

Note: This procedure applies only to surface-mounted or recessed dryers with triac mounted on the base plate. For touch button models with triac mounted on the timer bracket, the complete timer assembly must be replaced.

Warning



To Remove Existing Triac

1. Disconnect power supply and remove cover.

2. Remove white, yellow or pink, and black Push On connectors from triac.

3. Remove the two screws securing the triac to the base plate.

4. Remove the triac and place to one side for return to Service Department.

To Install New Triac

Note: On factory-installed triac, a white Heat sink Compound is interposed between the triac flange and the dryer base plate to ensure rapid conductivity of heat away from the triac. For service purposes this compound is replaced by a thin plastic gasket of heat conducting material, this must be sandwiched between the flange and the base plate during assembly.

1. Position new triac and pad on base plate with the Terminals positioned as shown in illustration below.

Insert and tighten the two self-threading screws and shake proof washers provided.

2. Attach the white wire Push On connector to the small spade

Terminal on the triac. The black wire from the Terminal Block should then be attached to the next Terminal round in a clockwise direction and the yellow or pink wire to the remaining Terminal.

3. Replace dryer cover. Switch on electrical supply and test operation, allow 10 seconds for the controller to stabilize before placing hands in front of lens

(automatic units).


28

Installation Of Automatic Controller

Warning



Older units have an intermediate plug and socket in the wiring, this has now been discontinued and can be removed with the faulty controller. The wiring on older units may be sleeved, this was later replaced by plastic cable ties. Some early 115 volt dryers had 4 way terminal blocks instead of the current 3 way blocks, in these dryers the wires to the 4 th

terminal should not be disturbed.

To Remove Control Unit

1. Remove outlet grille from front of fan case by unscrewing the securing screws.

2. Remove the screws securing the control unit to the base plate. (Note the different position of recessed and surface-mounted screws).

3. If the control unit wiring is secured by cable ties, carefully cut these to free the 4 wires from other wiring.

4. Remove the Push On Terminal securing the white wire to the triac.

5. Disconnect the controller wires from terminals 1, 2, and 3 on the terminal block. Leave all other wires in position.

6. Carefully lift control out of base plate. Avoid disturbing other wiring.

(Note: On recessed dryers it will be necessary to slide the control to the right to clear the fan case).

To Install New Control Unit

1. Position the new control unit on the base plate to line up with the screw holes and secure with the screws and washers previously removed.

2. Route wiring under element tube and connect wiring as follows: white wire with Push On Terminal to triac. Black wire to Terminal 1 (with existing black wire). Red wire to Terminal 2 (with existing red wire).

Pink wire to Terminal 3 (with existing wiring).

3. Secure all wires to existing wires with a minimum of 2 cable ties.

4. Replace grille and sealing gasket and secure with screws previously removed.

5. Check all wires for security and all screws for tightness.

6. Replace cover. Switch on electric supply.

7. Allow 10 seconds for the controller to stabilize and check operation of the dryer. If the operation is intermittent check that the controller has a clear view out of the cover aperture, use the spacers provided to raise the controller if required.


28

Instructions For Installation Of Sensor Board

Warning


Fig 1


There are two methods fixing sensor boards.

1. Fixed with five screws, Fig 1.

2. Fixed with three screws, Fig 2.

In both cases the orientation of the board is critical.

Fig 2

1. Switch off mains supply and remove cover. Place cover face downward on a bench using a cloth to protect the finish.

2. Remove the screws securing the board to the collar or bracket.

3. Mount the new board.

4. Replace cover. Switch on electrical supply and carry out normal hand drying procedure to test operation.


28

Instructions For The Replacement

Of Motor Brushes

Warning



The brush spares kit contains two brushes.

Always replace BOTH brushes.

EMD MOTOR

To remove the brush:

1. Squeeze the sides of the retainer and ease it over the stud with a small screwdriver.

2. Remove the retainer, cap and brush. Do not mislay the small cap spring.

To replace the brush:

1. Insert the new brush into the holder.

2. Place the cap, with the cap spring inside it, over the brush spring and press it over the holder.

3. Slide the retainer down the cap and snap it into position over the stud.

SINTECH MOTOR

On this motor the brush is replaced by changing the complete brush box assembly.

To remove the brush box assembly:

1. Pull the connector off the terminal tab, (A).

2. Depress the retaining tab with a small screwdriver and pull out the brush box, (B) and (C).

To replace the brush box assembly:

1. Insert the new brush box and push it down until the retaining tab is level with the slot in the motor end frame.

2. Bend out the retaining tab.

3. Replace the connector on the terminal tab.

AMETEK & WINSTON MOTORS

On this motor the brush is replaced without disturbing the brush box.

To remove the brush:

1. Depress the locking tab in the connector with a small screwdriver, (A).

2. Slide out the connector and remove the brush,

(B) and (C).

To replace the brush:

1. Insert the new brush into the holder.

2. Press the spring down with a screwdriver until it is below the connector slot, (D).

3. Push the connector into the slot until it locks into position, (E). Make sure that all of the top coil is under the connector.


28

INSTALLATION INSTRUCTIONS BOBRICK

SURFACE-MOUNTED HAND DRYERS

ELECTRICAL CHARACTERISTICS.

115V AC, 20 Amp, 50/60 Hz, Single Phase, UL/c-UL listed.

208–240V AC, 9–10 Amp, 50/60 Hz, Single Phase, UL/c-UL listed, VDE approved.

REMOVAL OF COVER

Start installation of dryer by removing cover. To loosen two cover bolts insert Allen Wrench, provided with dryer, into holes located on bottom of cover on each side of air intake grille.

Make sure wrench fits into head of cover bolts and turn CLOCKWISE until bolts stop turning. When cover bolts are screwed in all the way, cover can be removed.

To remove cover, place a hand on each side of cover and push up toward top of dryer releasing cover from studs at top of mounting base. Lift cover off mounting base by pulling forward at the bottom and upward at the same time.

INSTALLATION OF MOUNTING BASE.

An Installation Template is supplied with each unit.

RECOMMENDED MOUNTING HEIGHTS.

Distance from floor to bottom mounting screw holes of mounting base (Dimension A).

Hand dryer.

Men’s Washrooms ................................................................. 46'' (117cm)

Women’s Washrooms ........................................................... 44'' (112cm)

Children’s Washrooms, ages 3-9 .......................................... 32'' (81cm)

Page 19

Children’s Washrooms, ages 9-12 ........................................ 36'' (91cm)

Children’s Washrooms, ages 12-15 ...................................... 40'' (102cm)


For Wheelchair Access ......................................................... 38'' (97cm)

Place mounting base on wall at the desired location of the installed dryer. See recommended mounting heights above. Use the mounting base or the template provided with dryer to mark location of four mounting screw holes and hole for electrical wiring if electrical supply is concealed in wall and will enter dryer from back through mounting base.

NOTE: Surface-mounted electrical supply is attached to mounting base in lower right corner. Flange of mounting base and bottom of cover are notched in lower right corner to accommodate connection of electrical conduit.

WARNING:

TURN ELECTRICAL POWER SUPPLY OFF BEFORE MAKING ELECTRICAL

CONNECTIONS.

DRYER MUST BE GROUNDED (EARTHED).

ELECTRICAL CONNECTION.

Connect dryer to nearest distribution panel. Use wire as required by local electrical code. In the United States and Canada use No. 12 wire or larger.

Wiring Instructions:

For 115 Volt Dryers: Connect ground (earthed) wire to ground (earthed) terminal marked

, the black or Hot wire to terminal marked L1 and neutral or white wire to terminal marked N.

DEDICATED LINE IS REQUIRED FOR EACH 115 VOLT DRYER.

For 208–240 Volt Dryers: Connect ground (earthed) wire to ground (earthed) terminal marked and the 208-240 Volt wires to terminals marked L(L1) and N (L2).

Secure electrical wire in strain relief clamp provided on mounting base.

REPLACE COVER.

Replace cover by positioning top of cover on studs on top of mounting base and tipping bottom of cover toward wall. Push bottom of cover firmly against wall.

NOTE: Space between cover and wall must be the same on four sides.

To tighten two cover bolts, insert Allen wrench into holes on bottom of cover. Make sure wrench fits into head of cover bolts and turn COUNTERCLOCKWISE until bolts are tightened.

NOTE: Do not over tighten cover bolts; over tightening cover bolts may damage enamel finish.

CHECK DRYER OPERATION.

To check operation of dryer, follow these instructions:

Page 20

For Touch Button Hair Dryers: Turn electrical power supply on. Touch the chrome-plated touch button once and dryer should turn on. Touch the touch button again after a few seconds and dryer should stop. If left on Hair Dryers will shut off after 80 seconds.

For Automatic Hand Dryers: Turn electrical power supply on. Position hands under nozzle and dryer should turn on. Remove hands from under nozzle and dryer should stop.

Page 21

INSTALLATION INSTRUCTIONS BOBRICK RECESSED

AIRCRAFT

®

HAND DRYERS

ELECTRICAL CHARACTERISTICS.

115V AC, 20 Amp, 50/60 Hz, Single Phase, UL/c-UL listed.

208–240V AC, 9–10 Amp, 50/60 Hz, Single Phase, UL/c-UL listed, VDE approved.

INSTALLATION OF RECESSED MOUNTING BOX.

An Installation Template is supplied with each unit.

RECOMMENDED MOUNTING HEIGHTS.

Distance from floor to bottom of framed wall opening (Dimension A).

Hand dryer

Men’s Washrooms ................................................................. 46'' (117cm)

Women’s Washrooms ........................................................... 43'' (109cm)

Children’s Washrooms, ages 3-9 .......................................... 31'' (79cm)

Children’s Washrooms, ages 9-12 ........................................ 35'' (89cm)



For the Handicapped ............................................................. 38'' (97cm)

Provide framed opening in wall 13-3/4'' wide x 9-1/2'' high x 3-3/4'' deep (349 x 241 x

95mm) at the desired location of the installed dryer. See recommended mounting heights above.

Frame the opening as shown in diagram to support recessed mounting box.

Place the recessed mounting box in wall and cut an opening in the framing to allow clearance for electrical conduit and fittings at one of the three conduit knockout locations.

Page 22

Fasten recessed mounting box to framing with minimum of four No. 10 (4.8mm) sheet metal screws (not furnished by Bobrick). Make sure flanges of mounting box are completely flat against finished wall surface. If necessary, use shims or spacers between mounting box and framed wall opening to prevent distortion to box as it is fastened to framing.

Install electrical conduit from nearest distribution panel to recessed mounting box. Attach conduit fittings to mounting box. Use wire as required by local electrical code. In the United

States and Canada use No. 12 wire or larger. Allow a minimum of 24'' (610mm) of wire to remain in recessed mounting box for connection to dryer terminals.

INSTALLATION OF ALUMINUM BASE UNIT INTO RECESSED MOUNTING BOX.

Start installation of aluminum base unit into recessed mounting box by removing cover. To loosen two cover bolts, insert Allen wrench, provided with dryer, into holes located on bottom edge of cover. Make sure wrench fits into head of cover bolts and turn CLOCKWISE until bolts stop turning. When both cover bolts are screwed in all the way, cover can be removed.

To remove cover, place a hand on each side of cover and push up toward top of dryer releasing cover from studs at top of aluminum base unit. Lift cover off base unit by pulling forward at the bottom and upward at the same time.

Insert aluminum base unit into recessed mounting box and fasten to top and bottom flanges of mounting box with the four 1/4-20 UNC (MG-1) screws provided.

WARNING:

TURN ELECTRICAL POWER SUPPLY OFF BEFORE MAKING ELECTRICAL

CONNECTIONS.

DRYER MUST BE GROUNDED (EARTHED).

ELECTRICAL CONNECTION.

Wiring Instructions:

For 115 Volt Dryers: Connect ground (earthed) wire to ground (earthed) terminal marked

, the black or Hot wire to terminal marked L1 and neutral or white wire to terminal marked N.

DEDICATED LINE IS REQUIRED FOR EACH 115 VOLT DRYER.

For 208–240 Volt Dryers: Connect ground (earthed) wire to ground (earthed) terminal marked and the 208-240 Volt wires to terminals marked L(L1) and N (L2).

Make sure excess wire does not interfere with operation of dryer.

REPLACE COVER.

Replace cover by positioning top of cover on studs on top of aluminum base unit and tipping bottom of cover toward aluminum base. Push bottom of cover firmly against base.

NOTE: Space between cover and base must be the same on bottom and both sides.

To tighten two cover bolts, insert Allen wrench into holes on bottom edge of cover. Make sure wrench fits into head of cover bolts and turn COUNTERCLOCKWISE until bolts are tightened. NOTE: Do not over tighten cover bolts; over tightening cover bolts may damage enamel finish.

CHECK DRYER OPERATION.

Page 23

To check operation of dryer, follow these instructions:

For Automatic Hand Dryers: Turn electrical power supply on. Position hands under nozzle and dryer should turn on. Remove hands from under nozzle and dryer should stop.

Page 24

LIMITED WARRANTY

The Bobrick Dryer and all parts (except motor brushes) are warranted to the original owner of the installed unit for ten years from date of original installation for AirCraft

®

Automatic and Touch Button hand and hair dryers and five years for AirPro

and AirGuard

®

®

and Fast Dry hand dryers, against defects in factory workmanship or material under normal use and service. *

Motor brushes shall be warranted for three years from date of installation. This warranty is limited to repair or exchange of defective parts at the option of Bobrick Washroom

Equipment, Inc.

THIS WARRANTY DOES NOT COVER ACCIDENTAL DAMAGE, IMPROPER

HANDLING OR INSTALLATION, OR REPAIRS MADE BY UNAUTHORIZED PERSONS,

AND SPECIFICALLY EXCLUDES CLAIMS FOR INDIRECT, ACCIDENTAL OR

CONSEQUENTIAL DAMAGES TO PROPERTY. THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO

THE SAME DURATION OF THE ABOVE WARRANTY.

Some states do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

* Normal service constitutes performing the following preventive maintenance procedures at six-month intervals.

Remove cover and clean any lint, dust or grease from air-intake grille and baffle from behind air-outlet nozzle.

Visually inspect motor brushes to insure remaining brush length is a minimum of 1/2 inch (12.7mm).

Labor costs for preventive maintenance shall be at owner's expense.

For repair or exchange of defective part, send the part, together with installation date and serial number, to BOBRICK.

Page 25

Schematic Diagram

115V Dryer


208-240V Automatic Dryer

Page 26


208-240V Touch Dryer

Page 27


QuietDry Dryers

115V

208-240V

C - Cutout

H – Heater

M – Motor

TS – Timer/Sensor

Page 28

AirCraft , AirGuard , AirPro & QuietDry Dryer Guide

AirCraft

®

,

AirGuard

®

, AirPro

®

& QuietDry

™

Dryer Guide

AirCraft

, AirGuard

, AirPro

& Fast Dry Dryers

Contents

AirCraft

Dryers

Product Identification

Surface-Mounted Dryers:

B-700 Automatic Hand & Face (pictured)

B-701 Touch Button Hand & Face

B-731 Touch Button Hair

Recessed Dryers:

B-750 Automatic Hand & Face (pictured)

B-751 Touch Button Hand & Face

B-781 Touch Button Hair

AirGuard

Dryer

B-708 Automatic

Series Variations:

Series G lower profile cover, no nameplate or printing. (pictured)

Not all replacement parts are interchangeable, see parts list .

AirPro

Dryer

B-709 Touch Button

B-709 Automatic (pictured)

Series Variations:

Series A touch button model, metal nameplate.

Series B automatic model, metal nameplate.

Series C automatic model, lower profile cover, no nameplate.

Not all replacement parts are interchangeable, see parts list .

QuietDry Dryer

B-770 White cover

B-778 Chrome cover

Diagnostic Sheet For AirCraft

, AirGuard

, AirPro

& QuietDry™ Dryers.

Problem

Possible Cause

Possible Solution

Problem

Possible Cause

Possible Solution

Screwdriver Test for Touch Button Dryers

Field Replacement Parts

AirCraft

Dryer Replacement Parts

AirGuard

, AirPro

& QuietDry™ Dryer

Replacement Parts

Installation Instructions

Installation Instructions

Page

Cover Replacement

Installation Of Touch Controller

Installation Of Base Plate Mounted Triac

Installation Of Automatic Controller

Instructions For Installation Of Sensor Board

Instructions For The Replacement

Of Motor Brushes

INSTALLATION INSTRUCTIONS BOBRICK

SURFACE-MOUNTED HAND DRYERS

INSTALLATION INSTRUCTIONS BOBRICK RECESSED

AIRCRAFT

HAND DRYERS

LIMITED WARRANTY

Schematic Diagram