Sony SCD-XE600 E Super Audio CD Player SERVICE MANUAL
The SCD-XE600 E is a Super Audio CD player that can play back both Super Audio CDs and standard CDs. It features a variety of playback modes, including continuous play, shuffle play, and program play. It also includes a multi-channel decoding function and an optical digital output for connecting to an external audio system. This player is a great way to enjoy high-quality audio playback from your Super Audio CDs and CDs.
advertisement
SERVICE MANUAL
SCD-XE600
E Model
Model Name Using Similar Mechanism NEW
CD Mechanism Type CDM66D-DVBU50
Base Unit Name
Optical Traverse Unit Name
DVBU50
DBU-3
When a Super Audio CD is played
Playing frequency range 2 Hz to 100 kHz
Frequency response 2 Hz to 40 kHz (–3 dB)
Dynamic range 100 dB or more
Total harmonic distortion rate
0.0035 % or less
Wow and flutter Value of measurable limit
(
±0.001 % W. PEAK) or less
When a CD is played
Frequency response
Dynamic range
2 Hz to 20 kHz
96 dB or more
Total harmonic distortion rate
0.0039 % or less
Wow and flutter Value of measurable limit
(
±0.001 % W. PEAK) or less
Output connector
ANALOG
5.1CH OUT
Jack type Output level
Phono jacks
2 Vrms (at
50 kilohms)
Load impedance
Over 10 kilohms
DIGITAL
(CD) OUT
OPTICAL*
Square optical output connector
–18 dBm (Light emitting wave length:
660 nm)
* Output only the audio signals of the CD
SPECIFICATIONS
General
Laser
Power requirements
Power consumption
Dimensions (w/h/d)
Mass (approx.)
Semiconductor laser
(Super Audio CD:
λ= 650 nm) (CD:
λ= 780 nm)
Emission duration: continuous
110 V AC, 60 Hz
15 W
430
× 95 × 283 mm incl. projecting parts
3.1 kg
Supplied accessories
Audio connecting cord
Remote commander
Battery
Red and White 2 (1)
RM-SX800 (1)
R6 (size-AA) (2)
Design and specifications are subject to change without notice.
SUPER AUDIO CD PLAYER
9-879-168-01
2004J0579-1
© 2004.10
Sony Corporation
Audio Group
Published by Sony Engineering Corporation
SCD-XE600
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during repairing.
• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
This appliance is classified as a CLASS 1
LASER product.
This label is located on the rear exterior.
TABLE OF CONTENTS
1. SERVICING NOTES
......................................................... 3
2. GENERAL
............................................................................ 4
3. DISASSEMBLY
3-1.
Disassembly Flow .............................................................. 6
3-2.
Case (408226) ..................................................................... 6
3-3.
Main Board ......................................................................... 7
3-4.
Panel Loading ..................................................................... 7
3-5.
Front Panel Block ............................................................... 8
3-6.
CD Mechanism Deck (CDM66D-DVBU50) ..................... 8
3-7.
Base Unit (DVBU50) ......................................................... 9
3-8.
RF Board, Optical Traverse Unit ........................................ 9
3-9.
Loading Board, Motor (L) Assy (Loading) (M151) ......... 10
4. TEST MODE
...................................................................... 11
5. DIAGRAMS
5-1.
Block Diagram ................................................................. 12
5-2.
Printed Wiring Board – RF Board – ................................. 14
5-3.
Schematic Diagram – RF Board – .................................... 15
5-4.
Printed Wiring Boards – MAIN Board – .......................... 16
5-5.
Schematic Diagram – MAIN Board (1/4) – ..................... 17
5-6.
Schematic Diagram – MAIN Board (2/4) – ..................... 18
5-7.
Schematic Diagram – MAIN Board (3/4) – ..................... 19
5-8.
Schematic Diagram – MAIN Board (4/4) – ..................... 20
5-9.
Printed Wiring Boards
– Display, Power Supply Section – .................................. 21
5-10. Schematic Diagram
– Display, Power Supply Section – .................................. 22
6. EXPLODED VIEWS
6-1.
Main Section ..................................................................... 28
6-2.
Front Panel Section .......................................................... 29
6-3.
CD Mechanism Deck Section
(CDM66D-DVBU50) ....................................................... 30
6-4.
Base Unit Section (DVBU50) .......................................... 31
7. ELECTRICAL PARTS LIST
......................................... 32
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts.
The flexible board is easily damaged and should be handled with care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
CLEANING OF OPTICAL PICK-UP LENS
In cleaning the lens of optical pick-up, use the air blower.
Never use a cotton swab for cleaning the lens of optical pick-up, which otherwise causes a trouble.
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURNS OFF
cam (66)
2 Pull out the tray in the direction of arrow B.
B
A
1
Insert a flat-head screwdriver in to a hole at the bottom, and rotate the cam (66) in the direction of arrow A.
SCD-XE600
3
SCD-XE600
SECTION 2
GENERAL
This section is extracted from instruction manual.
Index to Parts and Controls
Further details are provided on the pages indicated in parentheses.
Instructions in this manual describe the controls on the player. You can also use the controls on the remote if they have the same or similar names as those on the player.
Front Panel
1 2 3 4 5 6 7 8 l L qh qg qf qd
A
POWER switch
B
SA-CD/CD button
Each time you press the button while playing back a hybrid disc, the layer to be played back switches between the SA-CD layer and the CD layer.
C
PLAY MODE button
Press to select the play mode.
D
Disc tray
E
MULTI CHANNEL DECODING indicator
Turns on when you turn on the player, or when the
Multi-channel Super Audio CD is loaded and select the multi-channel playback area by pressing
MULTI/2CH.
F A
button
G x
button
H m/M
buttons
I l
AMS
L
dial
(AMS: Automatic Music Sensor)
qs qa q; 9
J X
button
K H
button
L
Display window
M
Remote sensor
N
TIME/TEXT button
Each time you press the button, the playing time of the track, the remaining time of the disc, or TEXT information appears in the display.
O
MULTI/2CH button
Press to select the playback area when a disc with the 2 channel area and the multi-channel area is
loaded.
P
MENU button
Press to enter the menu.
Press to exit from the menu and return to the normal display.
4
Remote
qg qf qd qs qa q;
9
8
1
2
3
4
5
6
7
A
CD1/2 (command mode) switch
Select the command mode.
B
CONTINUE button
Press to resume Continuous Play from Shuffle Play or Program Play.
SHUFFLE button
PROGRAM button
C
TIME/TEXT button
Each time you press the button, the playing time of the track, the remaining time of the disc, or TEXT information appears in the display.
D
DISPLAY MODE button
Press to turn the display information off or on.
E m/M
buttons
F
CLEAR button
Press to delete a programed track number.
G
LEVEL ADJ button
Press to adjust the output level balance for the
Multi-channel management function.
H
ENTER button
I
CHECK button
Press to check the programed order.
J
REPEAT button
K H
button
X
button
x
button
L
AMS
./>
buttons
(AMS: Automatic Music Sensor)
M
SA-CD/CD button
Each time you press the button while playing back a hybrid disc, the layer to be played back switches between the SA-CD layer and the CD layer.
N
MULTI/2CH button
Press to select the playback area when a disc with the 2 channel area and the multi-channel area
(page 5) is loaded.
O
DISC SKIP +/– buttons*
Press to select the disc.
*This button cannot be used in this player.
SCD-XE600
5
SCD-XE600
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
Note 1: The process described in can be performed in any order.
Note 2: Without completing the process described in , the next process can not be performed.
SET
3-2. CASE (408226)
(Page 6)
3-4. PANEL LOADING
(Page 7)
3-3. MAIN BOARD
(Page 7)
3-5. FRONT PANEL BLOCK
(Page 8)
3-6. CD MECHANISM DECK
(CDM66D-DVBU50)
(Page 8)
3-7. BASE UNIT (DVBU50)
(Page 9)
3-8. RF BOARD,
OPTICAL TRAVERSE
UNIT (DBU-3)
(Page 9)
Note: Follow the disassembly procedure in the numerical order given.
3-2.
CASE (408226)
4 case (408226)
1 two screws
(case 3 TP2)
3-9. LOADING BOARD,
MOTOR (L) ASSY
(LOADING) (M151)
(Page 10)
3 screw
(BVTP 3 × 8)
2 two screws
(case 3 TP2)
6
3-3.
MAIN BOARD
1 wire (flat type) (31 core)
(CN702)
2 connector
(CN151)
3-4.
PANEL LOADING
4 panel loading
1 wire (flat type) (13 core)
(CN301)
2 connector
(CN901)
3 screw
(BVTP 3 × 8)
6
MAIN board
5
PC board holder
4 three screws
(BVTP 3 × 8)
SCD-XE600
3 tow claws cam (66)
2 Pull out the tray in the direction of arrow B.
B
1 Insert a flat-head screw driver in to a hold at the bottom, and rotate the cam (66) in the direction of arrow A.
A
7
SCD-XE600
3-5.
FRONT PANEL BLOCK
2 connector
(CN101)
2 connector
(CN891)
4 claw
1 wire (flat type) (31 core)
(CN301)
5 front panel block
3-6.
CD MECHANISM DECK (CDM66D-DVBU50)
4 claw
3 three screws
(BVTP 3 × 8)
3 three screws
(BVTP 3 × 8)
4
CD mechanism deck
(CDM66D-DVBU50)
2 connector (CN151)
1 wire (flat type) (31 core)
(CN702)
8
SCD-XE600
3-7.
BASE UNIT (DVBU50)
2 optical pick-up block
(DVBU50)
1 floating screw
(DIA. 12)
3-8.
RF BOARD, OPTICAL TRAVERSE UNIT
6 three step screws (M3)
2 claw
5
RF board
1 two screws
(BTTP M2.6)
7 optical traverse unit
(DBU-3)
3 flexible flat cable (24 core)
(CN001)
4 flexible board
(CN003)
9
SCD-XE600
3-9.
LOADING BOARD, MOTOR (L) ASSY (LOADING) (M151)
5 belt (LD)
4 gear (LD)
1 two claws
6 two screws
(B2.6 × 4)
3 tray (66)
2
7 Remove two solders.
9 motor (L) assy (loading)
(M151)
8 LOADING board
10
SCD-XE600
SECTION 4
TEST MODE
PANEL CHECK MODE
Procedure:
1. While pressing the m button and l AMS L knob, press the [POWER] button to turn the power on.
2. When enter the Panel Check mode, fluorescent indicator tube and LED all lights up for 5 seconds.
3. Press the H key of remote commander to enter the Key Check mode and display “KEY CHECK 12”.
(*1)
4. Each button is pressed, the display number of “KEY CHECK” is increases.
5. All buttons of twelve are pressed, exit the Key Check mode and enter the Jog Check mode, then display “JOG CHECK”.
6. Turn the l AMS L knob clockwise until “15” is displayed on the calendar area.
7. Turn the l AMS L knob counterclockwise until “1” is black out on the calendar area and jog check is OK and display “TEST
END”.
8. Press the [POWER] button to turn the power off and release the Panel Check mode.
*1) If press the x key, it displays “KEY CHECK 19”. However, this mode is for the model with changer. Therefore, it does not become OK unless 19 buttons are pressed. If entered to this mode by mistake, press the [POWER] button to turn the power off and repeat operation form step 1.
TEST MODE
1. Entering The Test Mode
While press the [MENU] button and l AMS L knob, press the [POWER] button to turn the power on and enter the Test Mode and display “DIAG MODE”.
2. Operating The Test Mode
Procedure:
1. Turn the l AMS L knob to select the command number (hexadecimal number) (refer to the following table for command number).
2. Press the l AMS L knob to execute the selected command item.
3. Releasing The Test Mode
Press the [POWER] button to turn the power off.
4. The Commands in Test Mode
Command No.
Command name
12
13
14
15
16
17
18
19
1A
24
27
31
45
61
7C
81
82
92
93
9D
LD ON/OFF
SPIN ON/OFF
FSRV ON/OFF
TSRV ON/OFF
CLV ON/OFF
SSRV ON/OFF
Item
Turn on/off the laser diode
Turn on/off the spindle motor
Turn on/off the focus servo
Turn on/off the tracking servo
Turn on/off the spindle CLV servo, when both focus servo and tracking servo are on
Turn on/off the spindle CLV servo, when all servo of focus servo, tracking servo and spindle servo are on
Turn on all servo ALL SRV ON
ALL SRV OFF
DISC STOP
ADJ FCSBIAS
FOCUS AGC
PI/FE OFSET
TRACKING AGC
I/F VERSION
ERR CHECK
WATER MARK
PLAY&RFD ON
Turn off all servo
Stop the disc rotation (useful as overdrived)
Automatically adjust the focus bias (*2)
Automatically adjust the focus servo gain (*2)
Automatically adjust the offset signal of PI, PE and TE (*2)
Automatically adjust the focus servo gain (*2)
DISC DETECT
FJUMP TEST
Judge the disc type (when SA-CD, “SL” or “DL” is displayed)
Focus jump test mode
SYSTEM VERSION Display the version of system microcomputer for 2 seconds
Display the version of IF microcomputer for 2 seconds
Error rate display (to stop, press the x button) for CD display “92 C1 C2 0xff” for SA-CD display “92 PI1 PO PI2”
WaterMark display display “93 xxxx” (“xxxx” is value of pspamp)
Measuring the jitter (to stop, press the x button) display: “9D xx 0xff 0xff” (“xx” is measuring value of jitter)
*2) Not used in servicing
11
SCD-XE600
SECTION 5
DIAGRAMS
5-1.
BLOCK DIAGRAM
OPTICAL TRAVERSE UNIT (DBU-3)
6,14
1
7
9
2
10
5
3
8
17
DVDLD
VCC
VC
RF
A
B
C
D
E
F
A5V
Q001
LD
DRIVE
Q002
LD
DRIVE
19
CDLD
15
12
SW
PD
VR
4
GND
FOCUS
COIL
TRACKING
COIL
FCS+
FCS-
TR+
TR-
M902
(SLED)
M
SLA+
SLA-
SLB+
SLB-
M901
(SPINDLE)
M
SPM-
SPM+
M151
(LOADING)
M
LOADP
LOADN
• Signal Path
: SACD
: CD
: CD DIGITAL OUT (OPTICAL)
SCD-XE600
IC001
RF AMP
IC712
MOTOR/COIL DRIVER
IC706
DIGITAL SERVO,
DIGITAL SIGNAL PROCESSOR
LIMIT
IN
SWITCH
D509
12
16
7
S841-845,
S851,855,
S861-865
IC802
SIRCS
KEY
INDICATION TUBE
FL801
3
IC708
16M SDRAM
9
8
IC701
RESET
D511
IC705
MASTER CONTROL
IC702
EEPROM
IC801
DISPLAY CONTROLLER
IN
OUT
9
X321
11.2896MHz
5 6
3 4
11
13
8 1 2
IC320
INVERTER
IC703
+1.8V REG
+1.8V
+5V
D801
LED
Q826
AU+
+3.3V
IC950
+5V REG
IC920
+3.3V REG
IC985
AU+ REG
MUTE
MUTE REG
Q961
+12V
RECT
D960,961
IC260
DAC
IC400(1/2)
6
AMP
IC400(2/2)
AMP
2
MUTE
Q401,402
MUTE
Q501,502
L MUTE
Q303
R MUTE
Q305
IC230
DAC
SL
SR
IC430(1/2)
AMP
6
AMP
2
7
IC430(2/2)
MUTE
Q301
MUTE
Q431,432
MUTE
Q531,532
IC200
DAC
CENTER
SW
IC460(1/2)
AMP
6
IC460(2/2)
2
AMP
1
MUTE
Q462,463
MUTE
Q562,563
T101
POWER TRANSFORMER
VF2
VF1
D OUT
IC330
OPTICAL OUT
DIGITAL
OUT
OPTICAL
J351
L
R
ANALOG
5.1CH OUT
SL
SR
CENTER
SW
VFL
VFL REG
Q971
D971
RECT
D921-924
S891
POWER
RECT
D931-934
RECT
D936,937
12 12
SCD-XE600
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
•
Note on Printed Wiring Board:
•
X
: parts extracted from the component side.
•
Y
: parts extracted from the conductor side.
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from
(Side B) the pattern face are indicated.
Parts face side:
(Side A)
Parts on the parts face side seen from the parts face are indicated.
Note on Schematic Diagram:
• All capacitors are in µ F unless otherwise noted. pF: µµ F
50 WV or less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and
1
/
4
W or less unless otherwise specified.
• f
: internal component.
•
C
: panel designation.
Note: The components identified by mark
0
or dotted line with mark
0
are critical for safety.
Replace only with part number specified.
• Indication of transistor
C
Q
B E
These are omitted.
•
A
: B+ Line.
•
B
: B– Line.
• Voltages and waveforms are dc with respect to ground under no-signal conditions.
( no mark : SACD PLAY
) : CD PLAY
• Voltages are taken with a VOM (Input impedance 10 M Ω ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
: SACD
J : CD c
: CD DIGITAL OUT (OPTICAL)
• Circuit Boards Location
POWER SWITCH board
LED board
KEY board
DISPLAY board
PT board
RF board
MAIN board
LOADING board
SCD-XE600
13 13
SCD-XE600
5-2.
PRINTED WIRING BOARD – RF BOARD – •
See page 13 for Circuit Boards Location.
: Uses unleaded solder.
RF BOARD (SIDE A)
OPTICAL
TRAVERSE
UNIT
(DBU-3)
RF BOARD (SIDE B)
M901
SPINDLE MOTOR
M902
SLED MOTOR
SCD-XE600
14 14
SCD-XE600
5-3.
SCHEMATIC DIAGRAM – RF BOARD – •
See page 23 for Waveforms.
RF BOARD
OPTICAL
TRAVERSE
UNIT
(DBU-3)
C001
0.01
C002
0.01
CN001
24P
JL003
JL004
JL005
JL006
JL007
JL008
JL009
JL010
JL011
JL012
JL013
JL014
JL015
JL016
JL017
JL018
JL019
JL020
JL021
JL022
JL023
R003
100
CN003
9P
JL024
JL025
JL026
JL027
JL028
JL029
JL030
JL031
R013
10k
C027 0.01
C004
22
6.3V
C044
10
16V
C039
0.01
R045
220
R009
820
C015
0.0047
JW001
C016 0.0047
JW002
C019
560p
C005
C006
C007
0.0022
0.0022
0.0022
C008
R052
R053
0.0022
0
0
R054 0
R055 0
JW003
JW004
R018
10k
C026
0.01
D001
1SS355TE-17
R007
33
JL001
Q001
2SB1132-T100-QR
L001
C009
10
16V
R008
33
R010
47k
C017
100
6.3V
R011
100
JL002
R020
33
Q002
2SB1132-T100-QR
C018
0.001
D004
1SS355TE-17
L002
C021
10
16V
R023
33
R025
47k
C024
0.001
R029
100
C034
0.022
C040
150p
R038
2.2M
R006
27k
C043
0.1
R004 0
C047 0.1
C048
C046
0.22
0.01
C011
0.01
CN002
31PIN
SCD-XE600
15 15
SCD-XE600
5-4.
PRINTED WIRING BOARDS – MAIN BOARD – •
See page 13 for Circuit Boards Location.
: Uses unleaded solder.
IC200
IC230
IC320
IC260
IC701
IC950
IC985
IC702
IC920
IC400
IC430
IC703
L
FRONT
R
L
R
CENTER
SURR
ANALOG
5.1CH OUT
SUB WOOFER
IC330
DIGITAL (CD)
OUT OPTICAL
LOADING BOARD
CN151
5
1
S271
LOADING
OUT
M
M151
(LOADING)
S272
LOADING
IN
1-645-721-
21
(21)
SCD-XE600
16 16
SCD-XE600
5-5.
SCHEMATIC DIAGRAM – MAIN BOARD (1/4) – •
See page 23 for Waveforms.
•
See page 23 for IC Block Diagram.
CN702
31P
STP702
XX
CL724
CL723
SL896
SL897
CL721
C733
0.047
RB604
4.7k
RB603
470
RB602
1k
RB613
10k
C729
0.001
R752
0
C734
0.1
CL767
C740
SL770
0.1
C739 0.1
CL824
CL823
CL827
CL826
CL825
CL766
CL765
CL764
CL763
CL762
C738 0.1
CL822
CL821
CL820
CL819
C737 0.1
CL761
CL760
CL759
CL758
CL757
CL756
CL755
TP713
C736 0.1
SL774
SL773
SL772
SL771
CL830
CL829
CL828
CL754
CL753
CL752
CL751
C743 0.1
SL778
SL777
SL776
SL775
C742
CL834
0.1
CL833
CL832
CL831
C741 0.1
SL798
C745
0.1
C746
0.1
C789
0.1
C754
220
4V
C751
2.2k
R783
10k
C755
0.1
C744
1
TP714
C757
0.1
TP715
SCD-XE600
17 17
TP730
XX
CL785
CL784
C765
0.1
SL871
SL875
CL782
SL872
CL781
CL780
CL779
CL778
CL777
CL776
CL775
C764
0.1
C771 0.1
CL877
CL876
CL875
CL874
CL804
CL803
CL802
CL801
CL800
CL799
CL798
CL797
CL796
C770
0.1
C769
0.1
CL795
CL794
CL793
CL792
CL791
CL790
C768
0.1
CL789
CL788
CL787
CL786 C767
0.1
C766 0.1
RB617
470
CL873
CL872
CL871
CL870
RB616
470
CL869
CL867
CL866
RB615
470
CL865
CL864
C714
220
4V
IC703
µPC2918T-E1
C706
0.1
SCD-XE600
5-6.
SCHEMATIC DIAGRAM – MAIN BOARD (2/4) – •
See page 23 for IC Block Diagram.
•
See page 25 for
IC Pin Function Description.
CN703
13P
FB703 0UH
FB710 0UH
RB612
10k
RB601
10k
RB607
10k
RB606
10k
SCD-XE600
R708
100
FL606
0UH
C713
100 16V
C715 0.1
R731
10k
CL734
D511
DAP202UT106
C712
0.1
CL731
C711
0.1
CL891
CL890
CL889
CL888
CL733
CL732
STP703
XX
C704 0.1
R701 1k
CL708
C702 1
IC701
M51957BFP-600C
CL710
R707
1k
C705
0.1
R703 10k
C703
0.1
C701 0.1
R702 10k
CL743
CL722 CL726
C721 0.1
RB611
10k
RB605
10k
18 18
CL769
CL768
C748
0.1
SCD-XE600
5-7.
SCHEMATIC DIAGRAM – MAIN BOARD (3/4) –
C772 0.1
C775
0.1
CL805
R791 47
C777
10p
CL806
C778
0.1
C776
0.1
C779
0.1
C780
0.1
C782
0.1
IC708
HY57V161610ETP-7DR
C781
0.1
C815
0.015
C814
0.22
R861
270k
C825
0.0015
R858
120k
R860
680k
R878
470k
R877
470k
D509
DAP202UT106
R806 10
CL815
SL895
SL894
SL893
CL814 SL892
SL891
SL898
R880
100k
C793
0.1
C796
100
16V
C794
0.1
C795
100
16V
C787
0.1
R804
330
R831
10k
R840 100k
C800 0.1
R852
100k
R897
470k
C832
0.0047
R872
10k
C785
220
4V
C783
100
16V
R846
56k
R853
56k
C813
0.033
C804 0.1
R899
220k
C817
0.001
R870
33k
R869
56k
C816
0.001
R866
33k
R865
56k
C821
100p
R876
82k
R885
15k
C828
0.068
R889
0
R895
56k
R894
56k
C820
220p
R874
33k
R893
110k
R892
110k
C830
100p
RB609
10k
R820 150k
R819 150k
C709
220
4V
C716
100
16V
CL727
CL712
CL713
CL711
STP701
XX
CL728
CL729
CL809
CL808
CL807
CL812
CL813
RB610
47k
CN705
5P
M151
S271
S272
CN151
5P
SCD-XE600
19 19
SCD-XE600
5-8.
SCHEMATIC DIAGRAM – MAIN BOARD (4/4) – •
See page 23 for Waveforms.
•
See page 23 for IC Block Diagram.
SCD-XE600
SL215
SL216
SL217
SL220
IC320
D321
1SS357-TPH3
C324
1
C325
100
6.3V
R330 22
R328 22
SN74LVU04APWR
R321
1M
X321
11.2896M
C321
15p
R323
1k
R322
0
C322
15p
R324
100
C212
10
50V
SL201
SL231
SL261
SL262
CL201
IC260
DSD1751DBQR
CL868
C266
1
C242
10
50V
C268
1
C272
10
50V
Q305
UN5116-TX
C281
2200p
RB301
4.7k
CL301
C302
0.1
Q301
UN5116-TX
RB302
220k
Q303
UN5116-TX
C303
0.1
CL302
C305
0.1
C201
1000
6.3V
IC400(2/2)
NJM4565M(T
E2)
C404
1
47
C406
25V
R408
330
C405
0.1
R407
100k
Q401
T1L15L16
R409
2SC3624A-
220
R411 100
Q402
2SC3624A-T
1L15L16
FB201 0UH
R201 10k R202 33k
C202
47
6.3V
C402
0.001
RB402
6.8k
C403
150p
C502
0.001
C503
150p
RB502
6.8k
C362
0.1
IC400(1/2)
NJM4565M(T
E2)
R404
3.3k
R504
3.3k
R507
100k
C505
0.1
47
C506
25V
R508
330
Q501
2SC3624A-
T1L15L16
IC430(2/2)
NJM4565M(T
E2)
R509
220
C432
0.001
RB432
6.8k
C532
0.001
RB532
6.8k
IC430(1/2)
NJM4565M(T
E2)
C533
150p
IC460(2/2)
NJM4565M(T
E2)
Q502
2SC3624A-T
1L15L16
RB410
2.2k
R511
100
C364
0.1
C366
0.1
C436
47
25V
R438
330
C435
0.1
R434
3.3k
R437
100k
R534
3.3k
R537
100k
C535
0.1
R538
330
C536
47
25V
Q531
2SC3624A-
T1L15L16
C466
47
25V
R468
330
Q431
2SC3624A-
T1L15L16
R439
220
RB441
2.2k
R539
220
R469
220
Q432
2SC3624A-
T1L15L16
Q532
2SC3624A-
T1L15L16
RB442
2.2k
C564
1
C462
0.001
C562
0.001
RB462
6.8k
RB562
6.8k
C563
150p
NJM4565M(T
E2)
C465
0.1
R464
3.3k
R564
3.3k
C565
0.1
R467
100k
Q462
2SC3624A-
T1L15L16
R567
100k
Q562
2SC3624A-
T1L15L16
C566
47
25V
R568
330
R569
220
Q463
2SC3624A-T
1L15L16
Q563
2SC3624A-T
1L15L16
20 20
IC985
BA12FP-E2
C933
0.1
C924
470
10V
C934
470
16V
C953
0.1
C954
470
10V
IC920
BA33BC0T
C921
10000
10V
IC950
BA50BC0FP-
E2
Q961
DTC143TKA-
T146
R963
1k
R962
1k
C962 0.1
D960
DAN202UT106
C932
470
35V
D936
1SR154-400TE25
D931
1SR154-400TE25
D937
1SR154-400TE25
D933
1SR154-400TE25
C935
1000
16V
C931
10000
16V
C961
10
50V
UDZSTE
D963
-173.0B
D932
1SR154-400TE25
D934
1SR154-400TE25
D961
DAN202UT106
C910 0.001
ETP910
EARTH PLATE
D921
1SR154-400TE25
D923
1SR154-400TE25
C920 0.01
D922
1SR154-400TE25
D924
1SR154-400TE25
C901
0.01
D971
1SR154-400TE25
C970 0.01
C971
47
63V
Q971
2SB1260
R971
10k
R972
10k
R973
3.3k
D972
UDZSTE-17-33B
C972
10
50V
R975
33k
R976
100
R977
100
R978
22k
R979
10k
C973
22
16V
CN901
8P
C331
0.1
C351
0.1
CL202
J351
6P
ANALOG
5.1CH OUT
SCD-XE600
5-9.
PRINTED WIRING BOARDS – DISPLAY, POWER SUPPLY SECTION – •
See page 13 for Circuit Boards Location.
: Uses unleaded solder.
MULTI CHANNEL DECODING
M m
A
ROTARY ENCODER
.
AMS
>
PUSH ENTER x X H
POWER TRANSFORMER
S891
POWER
IC802
TIME/TEXT PLAY MODE MULTI/2CH SA-SD/CD MENU
AC IN
SCD-XE600
21 21
SCD-XE600
5-10. SCHEMATIC DIAGRAM – DISPLAY, POWER SUPPLY SECTION – •
See page 23 for Waveforms.
•
See page 27 for
IC Pin Function Description.
R864
4.7k
R863
2.2k
R862
2.2k
R861
1k
CN813
2P
CN805
2P
IC802
NJL73H400A
C832
0.01
R832
100
C831
47
6.3V
R831
47
Q821
DTC114EKA-T146
R821
100k
C821
0.001
C805
0.1
C806
0.1
C829
0.1
C819
0.01
TP26
R826
10k
TP126
C804
0.1
R820
10k
R841
1k
R842
2.2k
R843
2.2k
R844
4.7k
R845
10k
R819
10k
S841 S842 S843 S844 S845
R851
1k
R852
2.2k
R853
2.2k
R854
4.7k
S851
C816
0.001
C813
0.001
C812
0.001
C811
0.001
R856
10k
FB801
FB
Q826
2SC3624AT1L15L16
R858
82
R857
10k
S855
ENCORDER
CN804
2P
X801
5MHz
TP5
R805
10k
C802
0.1
C801
100
6.3V
Q824
DTC114EKA
-T146
Q825
DTC114EKA
-T146
Q822
DTC114EKA-T146
R822
100k
C822
0.001
Q823
DTC114EKA
-T146
R823
100k
C823
0.001
R824
100k
C824
0.001
R825
100k
C825
0.001
C827
0.1
CN801
13P
FL801
CN102
8P
SCD-XE600
T101
C101
0.0022
250V
CN101
2P
CN892
2P
S891
C891
0.0022
250V
CN891
2P
22 22
MULTI
CHANNEL
DECODING
D801
SEL5E20C-STP15
BLUE
C833
0.1
R834
10k
CN814
2P
•
Waveforms
– RF Board –
– MAIN Board –
– DISPLAY Board –
• IC Block Diagrams
– RF Board –
– MAIN Board –
IC200, IC230, IC260 DSD1751DBQR
SCD-XE600
23 23
SCD-XE600
SCD-XE600
50 49 48 47 46 45 44 43 42 41 40 39 38
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
– DISPLAY Board –
24
SCD-XE600
59
63
64
65
66
60
61
62
67
68
RS232CTx
RS232CRx
TRAY_OUT
P10
DRV_ON
SP_ON
P13
XLDON
TRMP, TRMM
P17
AVSS
DIAG
P96
P47 to 42
MODEL
JIT
VREF
AVCC
MD0, MD1
OSC2
OSC1
Pin Name
SDATA_DAC
SCLK_DAC
SLATR_DAC
CD0 to CD7
CVCC
CA0
VSS0
CA1 to CA8
PB1, PB2
LOAD_S0
LOAD_S2
LOAD_S1
TSENS
DSENS
TRAY_IN
• IC Pin Function Description
MAIN BOARD IC705 HD6432238RN57TEV (MASTER CONTROL)
41
42
43
44
45 to 50
51
52
53
54
55, 56
57
58
31
32
33
34
35
36
37
38
39, 40
Pin No.
1
2
3
4 to 11
12
13
14
15 to 22
23, 24
25
26
27
28
29
30
XRES
XNMI
XSTBY
VCC
XTAL
VSS1
EXTAL
FWE
MD2
PF7
I/O Description
O Serial data output to the D/A converter
O Serial data transfer clock signal output to the D/A converter
O Serial data latch pulse output to the D/A converter
I/O Two-way data bus with the DSP
– Power supply terminal (+3.3V)
O Address signal output to the DSP
– Ground terminal
O Address signal output to the DSP
O Not used
I Loading in switch input terminal
I Detection signal input for disc tray open Not used
I
I Loading out switch input terminal
Not used
I Disc in detection signal input terminal Not used
O Control signal for loading motor drive
I
I
–
–
I
I
I
I
–
O Not used
I Not used
O Control signal for loading motor drive
O Not used
O Stop signal output for the sled motor and focus/tracking coil
O Stop signal output for the spindle motor
O Not used
O Laser diode on/off control signal output to the RF amplifier
O Tray motor control signal output terminal Not used
I
I
I
O Not used
– Ground terminal
Not used
Not used
Not used
I
–
I
I Setting terminal for model discrimination
Jitter value input from the DSP
Reference voltage input terminal
Power supply terminal (+3.3V)
I Setting terminal for the CPU operational mode
O Sub system clock output terminal Not used
I
I
Sub system clock input terminal Not used
System reset signal input from the reset signal generator “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
Non-maskable interrupt signal input terminal Not used
Standby on/off control signal input terminal Not used
Power supply terminal (+3.3V)
System clock terminal (12.5 MHz) Not used
Ground terminal
System clock input terminal (11.2896 MHz)
Write enable signal input for flash memory Not used
Setting terminal for the CPU operational mode
Not used
25
SCD-XE600
EEPSI
EEPSCK
P36
IFSO
IFSI
IFSC
P74
XCS
P72 to P70
XIFINT
XINT0
PG2
MZR
Pin Name
XRD
XWR
XWRST
XWAIT
SMUTE
EPR/B
XEPCS
XEWC
P32
EEPSO
MZL
XIFCS
R_MUTE
L_MUTE
INIT_DAC
M/2
80
81
82
83
84
85
86
87
88 to 90
91
92
93
94
95
96
97
98
99
100
Pin No.
70
71
72
73
74
75
76
77
78
79
I/O Description
O Data read strobe signal output to the DSP
O Write strobe signal output to the DSP
O Reset signal output to the DSP
I Wait request signal input for bus cycle
O Muting on/off control signal output to the DSP
I Read/busy signal input from the EEPROM
O Chip select signal output to the EEPROM
O WC signal output to the EEPROM
O Not used
O Serial data output to the EEPROM
I
I
I
I
I Serial data input from the EEPROM
O Serial data transfer clock signal output to the EEPROM
O Not used
O Serial data output to the display controller
I Serial data input from the display controller
O Serial data transfer clock signal output to the display controller
O Not used
O Chip select signal output to the display controller
I Not used
Busy signal input from the display controller
Interrupt request signal input from the DSP
Not used
Zero data (R-CH) flag detection signal input from the D/A converter
I Zero data (L-CH) flag detection signal input from the D/A converter
O Chip select signal output to the display controller
O Muting on/off control signal output terminal
O Muting on/off control signal output terminal
O Not used
O Muting on/off control signal output terminal
26
SCD-XE600
DISPLAY BOARD IC801
µ
PD780232GC-706-8BT (DISPLAY CONTROLLER)
Pin No.
1
2
3
4
5
6
17
18
19 to 21
22
23
24
25
26
27 to 44
45 to 58
59
60
61 to 64
65 to 80
10
11
12
13
14
15
16
7
8
9
Pin Name
VDD1
VSS1
X1
X2
IC
RESET
P27/SCK1
P26/SI1
P25/SO1
P24/BUSY
P23
ACK P22
P21/SO3
SCK3
REC P00/INTP0
P01/INTP1
SIRCS P02/TI
AVSS
ANI3 to ANI1
ANI0
VSS0
AVDD
VDD0
TEST FIP52
FIP51 to FIP34
FIP33 to FIP20
VDD2
VLOAD
FIP19 to FIP16
FIP15 to FIP0
I/O
–
–
Description
Power supply terminal (+3.3V)
Ground terminal
I System clock input terminal (5 MHz)
O System clock output terminal (5 MHz)
– Not used
System reset signal input from the reset signal generator “L”: reset
I For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
Serial data transfer clock signal input from the master controller I
I Serial data input from the master controller
O Serial data output to the master controller
I/O Not used
O LED drive signal output terminal
O Busy signal output to the master controller
I/O Not used
I/O Not used
I Chip select signal input from the master controller
I/O Not used
I
I
I
–
SIRCS signal input terminal
Ground terminal
Front panel keys input terminal (A/D input)
Key input terminal (A/D input) Not used
–
–
Ground terminal
Power supply terminal (+3.3V)
– Power supply terminal (+3.3V)
I/O Test mode setting terminal “L”: test mode, normally fixed at “H”
I/O Not used
O Segments drive signal output to the fluorescent indicator tube
– Power supply terminal (+3.3V)
– Pull down resistor connection terminal of VFD controller and driver
O Segments drive signal output to the fluorescent indicator tube
O Grid drive signal output to the fluorescent indicator tube
27
SCD-XE600
NOTE:
• -XX and -X mean standardized parts, so they may have some difference from the original one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑ ↑
Parts Color Cabinet's Color
6-1. MAIN SECTION
SECTION 6
EXPLODED VIEWS
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Accessories are given in the last of the electrical parts list.
The components identified by mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number specified.
2
3
#1
CD mechanism deck section
(CDM66D-DVBU50)
10
front panel section
2
#1
12
T101
4
11
5
6
not supplied
7
#1
8
not supplied
#1
9
1
Ref. No.
Part No.
3
4
1
2
* 5
Description
4-255-243-21 PANEL LOADING
3-363-099-11 SCREW (CASE 3 TP2)
4-232-580-91 CASE (408226)
1-862-181-11 PT BOARD
3-703-244-00 BUSHING (2104), CORD
0 6
* 7
1-827-597-11 CORD, POWER
4-954-051-51 HOLDER, PC BOARD
28
#1
Remark Ref. No.
Part No.
8
9
10
11
12
Description
A-4752-595-A MAIN BOARD, COMPLETE
X-2022-049-1 FOOT ASSY
3-077-331-01 +BV3 (3-CR)
1-829-172-11 WIRE (FLAT TYPE) (31 CORE)
1-828-333-11 WIRE (FLAT TYPE) (13 CORE)
0 T101
#1
1-443-403-11 TRANSFORMER, POWER
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
Remark
SCD-XE600
6-2. FRONT PANEL SECTION
54
53
56
not supplied
56
55
57
56
56
56
not supplied
(LED board)
56
56
not supplied
60
not supplied
59
51
52
Ref. No.
Part No.
51
52
53
54
55
Description
4-232-622-21 KNOB (AMS)
3-354-981-11 SPRING (SUS), RING
X-2022-056-1 PANEL, FRONT ASSY
4-255-244-21 BUTTON, POWER
1-862-182-11 POWER SWITCH BOARD
Remark Ref. No.
Part No.
56
57
59
60
Description
3-087-053-01 +BVTP2-6 (3CR)
1-862-179-11 KEY BOARD
A-4752-665-A DISPLAY BOARD, COMPLETE
4-977-358-01 CUSHION
Remark
29
SCD-XE600
6-3. CD MECHANISM DECK SECTION (CDM66D-DVBU50)
207
204
not supplied
208
205
206
#2 not supplied
209
210
optical pick-up section
(DVBU50)
M151
203
201
202
Ref. No.
Part No.
201
202
203
204
205
Description
4-227-899-01 SCREW (DIA. 12), FROATING
1-645-721-11 LOADING BOARD
4-231-530-05 TRAY (66)
4-232-712-01 CAM (66)
4-232-710-01 PULLEY (LD)
206 4-232-713-01 BELT (LD)
Remark Ref. No.
Part No.
Description
207
208
209
210
4-232-711-01 GEAR (LD)
3-053-844-01 YOKE
4-231-529-01 CHASSIS (66)
4-232-682-01 CUSHION (66)
M151 A-4604-363-A MOTOR (L) ASSY (LOADING)
#2 7-621-775-10 SCREW +B 2.6X4
Remark
30
SCD-XE600
6-4. BASE UNIT SECTION (DVBU50)
254
257
256
255
257
256
257
256
258
252
251
The components identified by mark 0 or dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Ref. No.
Part No.
251
252
254
0 255
Description
4-218-253-52 SCREW (M2.6), +BTTP
A-4750-527-A RF BOARD, COMPLETE
4-240-953-05 HOLDER (66D)
1-478-637-31 OPTICAL TRAVERSE UNIT (DBU-3)
Remark
Ref. No.
Part No.
256
257
258
Description
3-053-847-31 INSULATOR
4-981-923-01 SCREW (M), STEP
1-824-106-12 CABLE, FLEXIBLE FLAT (24 CORE)
Remark
31
SCD-XE600
DISPLAY
SECTION 7
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set.
• -XX and -X mean standardized parts, so they may have some difference from the original one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example: uA.. : µA..
uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS uF : µF
• COILS uH : µH
The components identified by mark 0 or dotted line with mark.
0 are critical for safety.
Replace only with part number specified.
When indicating parts by reference number, please include the board.
Ref. No.
Part No.
Description
A-4752-665-A DISPLAY BOARD, COMPLETE
************************
4-949-935-41 CUSHION (FL)
C801
C802
C803
C804
C805
< CAPACITOR >
1-124-584-00 ELECT
1-164-156-11 CERAMIC CHIP
1-164-156-11 CERAMIC CHIP
1-164-156-11 CERAMIC CHIP
1-164-156-11 CERAMIC CHIP
100uF
0.1uF
0.1uF
0.1uF
0.1uF
20% 6.3V
25V
25V
25V
25V
C806 1-165-319-11 CERAMIC CHIP 0.1uF
50V
C811 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C812 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C813 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C816 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
Remark Ref. No.
Part No.
Description
< TRANSISTOR >
Q821 8-729-027-43 TRANSISTOR
Q822 8-729-027-43 TRANSISTOR
Q823 8-729-027-43 TRANSISTOR
Q824 8-729-027-43 TRANSISTOR
Q825 8-729-027-43 TRANSISTOR
Q826
R805
R817
R818
R819
R820
8-729-141-73 TRANSISTOR
< RESISTOR >
1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP
R821 1-216-845-11 METAL CHIP
R822 1-216-845-11 METAL CHIP
R823 1-216-845-11 METAL CHIP
R824 1-216-845-11 METAL CHIP
R825 1-216-845-11 METAL CHIP
C817 1-162-970-11 CERAMIC CHIP 0.01uF
C818 1-162-970-11 CERAMIC CHIP 0.01uF
10% 25V
10% 25V
C819 1-162-970-11 CERAMIC CHIP 0.01uF
10% 25V
C821 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C822 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C823 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C824 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C825 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C827 1-165-319-11 CERAMIC CHIP 0.1uF
50V
C829 1-165-319-11 CERAMIC CHIP 0.1uF
50V
C831 1-124-589-11 ELECT 47uF
C832 1-162-970-11 CERAMIC CHIP 0.01uF
20% 16V
10% 25V
R826
R831
R832
R841
R842
1-216-833-11 METAL CHIP
1-216-805-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-825-11 METAL CHIP
R843 1-216-825-11 METAL CHIP
R844 1-216-829-11 METAL CHIP
R845 1-216-833-11 METAL CHIP
R851 1-216-821-11 METAL CHIP
R852 1-216-825-11 METAL CHIP < CONNECTOR >
CN801 1-779-281-11 CONNECTOR, FFC (LIF (NON-ZIF)) 13P
FB801
< FERRITE BEAD >
1-414-595-11 INDUCTOR, FERRITE BEAD
R853 1-216-825-11 METAL CHIP
R854 1-216-829-11 METAL CHIP
R856 1-216-833-11 METAL CHIP
R857 1-216-833-11 METAL CHIP
R858 1-216-808-11 METAL CHIP
< SWITCH > < FLUORESCENT INDICATOR >
FL801 1-518-992-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC801 6-804-318-01 IC uPD780232GC-706-8BT-A
IC802 8-759-826-33 IC NJL73H400A
DTC114EKA-T146
DTC114EKA-T146
DTC114EKA-T146
DTC114EKA-T146
DTC114EKA-T146
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
Remark
2SC3624A-T1L15L16
10K
10K
10K
10K
10K
100K
100K
100K
100K
100K
10K
47
100
1K
2.2K
2.2K
4.7K
10K
1K
2.2K
2.2K
4.7K
10K
10K
82
S841 1-771-349-21 SWITCH, KEYBOARD (x)
S842 1-771-349-21 SWITCH, KEYBOARD (H)
S843 1-771-349-21 SWITCH, KEYBOARD (X)
S844 1-771-349-21 SWITCH, KEYBOARD (m)
S845 1-771-349-21 SWITCH, KEYBOARD (M)
S851 1-771-349-21 SWITCH, KEYBOARD (A)
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
32
SCD-XE600
DISPLAY KEY LED LOADING MAIN
Ref. No.
Part No.
Description Remark
S855 1-478-268-11 ENCODER, ROTARY
(. AMS >, PUSH ENTER)
Ref. No.
Part No.
Description
A-4752-595-A MAIN BOARD, COMPLETE
*********************
< VIBRATOR >
X801 1-795-058-21 VIBRATOR, CERAMIC (5MHz)
*************************************************************
1-862-179-11 KEY BOARD
**********
< CONNECTOR >
CN813 1-506-481-11 PIN, CONNECTOR 2P
< CAPACITOR >
C201 1-126-916-11 ELECT
C202 1-126-205-11 ELECT CHIP
C206 1-115-156-11 CERAMIC CHIP 1uF
C208 1-115-156-11 CERAMIC CHIP 1uF
C212 1-128-991-21 ELECT CHIP
Remark
1000uF 20% 6.3V
47uF 20% 6.3V
10uF 20%
10V
10V
50V
< RESISTOR >
R861 1-216-821-11 METAL CHIP
R862 1-216-825-11 METAL CHIP
R863 1-216-825-11 METAL CHIP
R864 1-216-829-11 METAL CHIP
< SWITCH >
1K
2.2K
2.2K
4.7K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
C236 1-115-156-11 CERAMIC CHIP 1uF
C238 1-115-156-11 CERAMIC CHIP 1uF
C242 1-128-991-21 ELECT CHIP 10uF
C266 1-115-156-11 CERAMIC CHIP 1uF
C268 1-115-156-11 CERAMIC CHIP 1uF
10V
10V
20% 50V
10V
10V
C272 1-128-991-21 ELECT CHIP 10uF 20% 50V
C281 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C302 1-164-156-11 CERAMIC CHIP 0.1uF
C303 1-164-156-11 CERAMIC CHIP 0.1uF
C305 1-164-156-11 CERAMIC CHIP 0.1uF
25V
25V
25V
S861 1-771-349-21 SWITCH, KEYBOARD (MENU)
S862 1-771-349-21 SWITCH, KEYBOARD (SA-CD/CD)
S863 1-771-349-21 SWITCH, KEYBOARD (MULTI/2CH)
S864 1-771-349-21 SWITCH, KEYBOARD (PLAY MODE)
S865 1-771-349-21 SWITCH, KEYBOARD (TIME/TEXT)
*************************************************************
LED BOARD
**********
C321 1-162-917-11 CERAMIC CHIP 15PF
C322 1-162-917-11 CERAMIC CHIP 15PF
C324 1-115-156-11 CERAMIC CHIP 1uF
C325 1-126-206-11 ELECT CHIP 100uF
C331 1-164-156-11 CERAMIC CHIP 0.1uF
C351 1-164-156-11 CERAMIC CHIP 0.1uF
C362 1-164-156-11 CERAMIC CHIP 0.1uF
C364 1-164-156-11 CERAMIC CHIP 0.1uF
C366 1-164-156-11 CERAMIC CHIP 0.1uF
C402 1-115-416-11 CERAMIC CHIP 0.001uF
5%
5%
5%
50V
50V
10V
20% 6.3V
25V
25V
25V
25V
25V
25V
< CAPACITOR >
C833 1-164-156-11 CERAMIC CHIP 0.1uF
< CONNECTOR >
CN814 1-506-481-11 PIN, CONNECTOR 2P
< LED >
D801 6-500-647-01 LED SEL5E20C-STP15
< RESISTOR >
25V
(MULTI CHANNEL DECORDING)
C403 1-164-217-11 CERAMIC CHIP 150PF
C404 1-115-156-11 CERAMIC CHIP 1uF
C405 1-107-826-11 CERAMIC CHIP 0.1uF
C406 1-128-992-21 ELECT CHIP 47uF
5%
10%
20%
C432 1-115-416-11 CERAMIC CHIP 0.001uF
5%
50V
10V
16V
25V
25V
C433 1-164-217-11 CERAMIC CHIP 150PF
C434 1-115-156-11 CERAMIC CHIP 1uF
C435 1-107-826-11 CERAMIC CHIP 0.1uF
C436 1-128-992-21 ELECT CHIP 47uF
5%
10%
20%
C462 1-115-416-11 CERAMIC CHIP 0.001uF
5%
50V
10V
16V
25V
25V
R834
* CN151
1-216-833-11 METAL CHIP 10K 5% 1/10W
*************************************************************
1-645-721-11 LOADING BOARD
**************
< CONNECTOR >
1-568-943-11 PIN, CONNECTOR 5P
C463 1-164-217-11 CERAMIC CHIP 150PF
C464 1-115-156-11 CERAMIC CHIP 1uF
C465 1-107-826-11 CERAMIC CHIP 0.1uF
C466 1-128-992-21 ELECT CHIP 47uF
5%
10%
20%
C502 1-115-416-11 CERAMIC CHIP 0.001uF
5%
50V
10V
16V
25V
25V
C503 1-164-217-11 CERAMIC CHIP 150PF
C504 1-115-156-11 CERAMIC CHIP 1uF
C505 1-107-826-11 CERAMIC CHIP 0.1uF
C506 1-128-992-21 ELECT CHIP 47uF
5%
10%
20%
C532 1-115-416-11 CERAMIC CHIP 0.001uF
5%
50V
10V
16V
25V
25V
< SWITCH >
S271 1-572-086-11 SWITCH, LEAF (LOADING OUT)
S272 1-572-086-11 SWITCH, LEAF (LOADING IN)
*************************************************************
C533 1-164-217-11 CERAMIC CHIP 150PF
C534 1-115-156-11 CERAMIC CHIP 1uF
C535 1-107-826-11 CERAMIC CHIP 0.1uF
C536 1-128-992-21 ELECT CHIP 47uF
5%
10%
20%
C562 1-115-416-11 CERAMIC CHIP 0.001uF
5%
50V
10V
16V
25V
25V
C563 1-164-217-11 CERAMIC CHIP 150PF
C564 1-115-156-11 CERAMIC CHIP 1uF
C565 1-107-826-11 CERAMIC CHIP 0.1uF
C566 1-128-992-21 ELECT CHIP 47uF
5% 50V
10V
10% 16V
20% 25V
33
SCD-XE600
MAIN
Ref. No.
Part No.
Description
C701 1-164-156-11 CERAMIC CHIP 0.1uF
C702 1-125-837-11 CERAMIC CHIP 1uF
C703 1-164-156-11 CERAMIC CHIP 0.1uF
C704 1-164-156-11 CERAMIC CHIP 0.1uF
C705 1-164-156-11 CERAMIC CHIP 0.1uF
C706 1-164-156-11 CERAMIC CHIP 0.1uF
C709 1-126-246-11 ELECT CHIP 220uF
C711 1-164-156-11 CERAMIC CHIP 0.1uF
C712 1-164-156-11 CERAMIC CHIP 0.1uF
C713 1-117-681-11 ELECT CHIP 100uF
C714 1-126-246-11 ELECT CHIP 220uF
Remark
25V
10% 6.3V
25V
25V
25V
25V
20% 4V
25V
25V
20% 16V
20% 4V
C715 1-164-156-11 CERAMIC CHIP 0.1uF
C716 1-117-681-11 ELECT CHIP 100uF
C721 1-164-156-11 CERAMIC CHIP 0.1uF
C722 1-107-826-11 CERAMIC CHIP 0.1uF
C723 1-125-837-11 CERAMIC CHIP 1uF
25V
20% 16V
25V
10% 16V
10% 6.3V
C726 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C727 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C729 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C730 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C731 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C733 1-165-176-11 CERAMIC CHIP 0.047uF
10% 16V
C734 1-107-826-11 CERAMIC CHIP 0.1uF
10% 16V
C736 1-164-156-11 CERAMIC CHIP 0.1uF
C737 1-164-156-11 CERAMIC CHIP 0.1uF
C738 1-164-156-11 CERAMIC CHIP 0.1uF
25V
25V
25V
C739 1-164-156-11 CERAMIC CHIP 0.1uF
C740 1-164-156-11 CERAMIC CHIP 0.1uF
C741 1-164-156-11 CERAMIC CHIP 0.1uF
C742 1-164-156-11 CERAMIC CHIP 0.1uF
C743 1-164-156-11 CERAMIC CHIP 0.1uF
25V
25V
25V
25V
25V
C744 1-115-156-11 CERAMIC CHIP 1uF
C745 1-107-826-11 CERAMIC CHIP 0.1uF
C746 1-164-156-11 CERAMIC CHIP 0.1uF
C748 1-164-156-11 CERAMIC CHIP 0.1uF
C749 1-107-826-11 CERAMIC CHIP 0.1uF
C750 1-115-156-11 CERAMIC CHIP 1uF
C751 1-216-825-11 METAL CHIP 2.2K
C752 1-164-156-11 CERAMIC CHIP 0.1uF
C753 1-164-156-11 CERAMIC CHIP 0.1uF
C754 1-126-246-11 ELECT CHIP 220uF
C755 1-164-156-11 CERAMIC CHIP 0.1uF
C756 1-164-156-11 CERAMIC CHIP 0.1uF
C757 1-164-156-11 CERAMIC CHIP 0.1uF
C758 1-164-156-11 CERAMIC CHIP 0.1uF
C759 1-164-156-11 CERAMIC CHIP 0.1uF
C760 1-164-156-11 CERAMIC CHIP 0.1uF
C761 1-164-156-11 CERAMIC CHIP 0.1uF
C762 1-164-156-11 CERAMIC CHIP 0.1uF
C763 1-164-156-11 CERAMIC CHIP 0.1uF
C764 1-164-156-11 CERAMIC CHIP 0.1uF
C765 1-164-156-11 CERAMIC CHIP 0.1uF
C766 1-164-156-11 CERAMIC CHIP 0.1uF
C767 1-164-156-11 CERAMIC CHIP 0.1uF
C768 1-164-156-11 CERAMIC CHIP 0.1uF
C769 1-164-156-11 CERAMIC CHIP 0.1uF
C770 1-164-156-11 CERAMIC CHIP 0.1uF
10V
10% 16V
25V
25V
10% 16V
5%
10V
1/10W
25V
25V
20% 4V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
25V
Ref. No.
Part No.
Description
C771 1-164-156-11 CERAMIC CHIP 0.1uF
C772 1-164-156-11 CERAMIC CHIP 0.1uF
C775 1-164-156-11 CERAMIC CHIP 0.1uF
C776 1-164-156-11 CERAMIC CHIP 0.1uF
C777 1-162-915-11 CERAMIC CHIP 10PF
C778 1-164-156-11 CERAMIC CHIP 0.1uF
C779 1-164-156-11 CERAMIC CHIP 0.1uF
C780 1-164-156-11 CERAMIC CHIP 0.1uF
C781 1-164-156-11 CERAMIC CHIP 0.1uF
C782 1-164-156-11 CERAMIC CHIP 0.1uF
C783 1-117-681-11 ELECT CHIP 100uF
C785 1-126-246-11 ELECT CHIP 220uF
C787 1-164-156-11 CERAMIC CHIP 0.1uF
C788 1-164-156-11 CERAMIC CHIP 0.1uF
C789 1-164-156-11 CERAMIC CHIP 0.1uF
C793 1-164-156-11 CERAMIC CHIP 0.1uF
C794 1-164-156-11 CERAMIC CHIP 0.1uF
C795 1-117-681-11 ELECT CHIP 100uF
C796 1-117-681-11 ELECT CHIP 100uF
25V
25V
25V
20% 16V
20% 16V
C800 1-164-156-11 CERAMIC CHIP 0.1uF
C804 1-164-156-11 CERAMIC CHIP 0.1uF
25V
25V
C809 1-164-677-11 CERAMIC CHIP 0.033uF
10% 16V
C813 1-164-677-11 CERAMIC CHIP 0.033uF
10% 16V
C814 1-115-467-11 CERAMIC CHIP 0.22uF
10% 10V
C815 1-164-245-11 CERAMIC CHIP 0.015uF
10% 25V
C816 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C817 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C819 1-115-156-11 CERAMIC CHIP 1uF 10V
C820 1-164-816-11 CERAMIC CHIP 220PF 2% 50V
C821 1-162-927-11 CERAMIC CHIP 100PF
C822 1-164-816-11 CERAMIC CHIP 220PF
5%
2%
50V
50V
C825 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V
C828 1-110-563-11 CERAMIC CHIP 0.068uF
10% 16V
C829 1-110-563-11 CERAMIC CHIP 0.068uF
10% 16V
0.5PF
50V
25V
25V
25V
25V
25V
20% 16V
20% 4V
25V
25V
Remark
25V
25V
25V
25V
C830 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C832 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C901 1-162-970-11 CERAMIC CHIP 0.01uF
10% 25V
C910 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C920 1-162-970-11 CERAMIC CHIP 0.01uF
10% 25V
C921 1-128-546-11 ELECT 10000uF 20% 10V
C923 1-164-156-11 CERAMIC CHIP 0.1uF
25V
C924 1-126-935-11 ELECT
C931 1-126-939-11 ELECT
C932 1-126-951-11 ELECT
470uF
10000uF
470uF
20%
20%
20%
16V
16V
35V
C933 1-164-156-11 CERAMIC CHIP 0.1uF
C934 1-126-935-11 ELECT 470uF
25V
20% 16V
C935 1-126-767-11 ELECT 1000uF 20% 16V
C953 1-164-156-11 CERAMIC CHIP 0.1uF
25V
C954 1-126-935-11 ELECT 470uF 20% 16V
C961 1-128-991-21 ELECT CHIP 10uF
C962 1-164-156-11 CERAMIC CHIP 0.1uF
C970 1-162-970-11 CERAMIC CHIP 0.01uF
C971 1-128-552-51 ELECT 47uF
C972 1-128-991-21 ELECT CHIP 10uF
C973 1-126-395-11 ELECT CHIP 22uF
20%
10%
20%
20%
20%
50V
25V
25V
63V
50V
16V
34
SCD-XE600
MAIN
Ref. No.
Part No.
Description
< CONNECTOR >
Remark
CN702 1-784-387-11 CONNECTOR, FFC/FPC 31P
CN703 1-793-989-21 FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 13P
CN901 1-784-924-11 PIN, CONNECTOR 8P
< DIODE >
D321 8-719-027-76 DIODE 1SS357-TPH3
D509 8-719-941-09 DIODE DAP202U
D511 8-719-941-09 DIODE DAP202U
D921 8-719-053-18 DIODE 1SR154-400TE-25
D922 8-719-053-18 DIODE 1SR154-400TE-25
D923 8-719-053-18 DIODE 1SR154-400TE-25
D924 8-719-053-18 DIODE 1SR154-400TE-25
D931 8-719-053-18 DIODE 1SR154-400TE-25
D932 8-719-053-18 DIODE 1SR154-400TE-25
D933 8-719-053-18 DIODE 1SR154-400TE-25
D934 8-719-053-18 DIODE 1SR154-400TE-25
D936 8-719-053-18 DIODE 1SR154-400TE-25
D937 8-719-053-18 DIODE 1SR154-400TE-25
D960 8-719-941-86 DIODE DAN202U
D961 8-719-941-86 DIODE DAN202U
D963 6-500-696-01 DIODE UDZSTE-173.0B
D971 8-719-053-18 DIODE 1SR154-400TE-25
D972 8-719-083-87 DIODE UDZSTE-1733B
D973 8-719-069-60 DIODE UDZSTE-179.1B
< GROUND TERMINAL >
ETP910 1-537-771-21 TERMINAL BOARD, GROUND
< FERRITE BEAD >
FB201 1-500-283-11 INDUCTOR, FERRITE BEAD
FB703 1-414-595-11 INDUCTOR, FERRITE BEAD
FB710 1-414-595-11 INDUCTOR, FERRITE BEAD
< FILTER >
FL606 1-234-177-21 FILTER, CHIP EMI
< IC >
IC200 6-703-420-01 IC DSD1751DBQR
IC230 6-703-420-01 IC DSD1751DBQR
IC260 6-703-420-01 IC DSD1751DBQR
IC320 8-759-549-25 IC SN74LVU04APWR
IC330 6-600-012-01 IC TOTX141L (DIGITAL (CD), OUT OPTICAL)
IC400 8-759-710-97 IC NJM4565M-D
IC430 8-759-710-97 IC NJM4565M-D
IC460 8-759-710-97 IC NJM4565M-D
IC701 8-759-636-64 IC M51957BFP-600C
* IC702 6-703-671-01 IC BR9040F-WE2
IC703 6-700-398-01 IC uPC2918T-E1
IC705 6-805-043-01 IC HD6432238RN57TEV
IC706 8-752-420-59 IC CXD2754Q
IC708 6-705-992-11 IC HY57V161610ETP-7DR
IC712 6-702-157-01 IC FAN8035L
IC920 6-705-463-01 IC BA33BC0T
IC950 6-705-469-01 IC BA50BC0FP-E2
IC985 8-759-460-81 IC BA12FP-E2
Ref. No.
J351
Part No.
Description
< JACK >
1-785-536-11 JACK, PIN 6P (ANALOG 5.1CH OUT)
< TRANSISTOR >
Remark
Q301 8-729-924-04 TRANSISTOR
Q303 8-729-924-04 TRANSISTOR
Q305 8-729-924-04 TRANSISTOR
Q401 8-729-141-73 TRANSISTOR
Q402 8-729-141-73 TRANSISTOR
Q431 8-729-141-73 TRANSISTOR
Q432 8-729-141-73 TRANSISTOR
Q462 8-729-141-73 TRANSISTOR
Q463 8-729-141-73 TRANSISTOR
Q501 8-729-141-73 TRANSISTOR
Q502
Q531
Q532
Q562
Q563
8-729-141-73 TRANSISTOR
8-729-141-73 TRANSISTOR
8-729-141-73 TRANSISTOR
8-729-141-73 TRANSISTOR
8-729-141-73 TRANSISTOR
Q961 8-729-027-56 TRANSISTOR
Q971 8-729-019-72 TRANSISTOR
< RESISTOR >
DTA143TU
DTA143TU
DTA143TU
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
DTC143TKA-T146
2SB1260
R201 1-216-833-11 METAL CHIP
R202 1-216-839-11 METAL CHIP
R321 1-216-857-11 METAL CHIP
R322 1-216-864-11 SHORT CHIP
R323 1-216-821-11 METAL CHIP
R324 1-216-809-11 METAL CHIP
R326 1-216-801-11 METAL CHIP
R328 1-216-801-11 METAL CHIP
R330 1-216-801-11 METAL CHIP
R404 1-216-827-11 METAL CHIP
R407 1-216-845-11 METAL CHIP
R408 1-216-815-11 METAL CHIP
R409 1-216-813-11 METAL CHIP
R411 1-216-809-11 METAL CHIP
R434 1-216-827-11 METAL CHIP
R437 1-216-845-11 METAL CHIP
R438 1-216-815-11 METAL CHIP
R439 1-216-813-11 METAL CHIP
R464 1-216-827-11 METAL CHIP
R467 1-216-845-11 METAL CHIP
R468 1-216-815-11 METAL CHIP
R469 1-216-813-11 METAL CHIP
R504 1-216-827-11 METAL CHIP
R507 1-216-845-11 METAL CHIP
R508 1-216-815-11 METAL CHIP
R509 1-216-813-11 METAL CHIP
R511 1-216-809-11 METAL CHIP
R534 1-216-827-11 METAL CHIP
R537 1-216-845-11 METAL CHIP
R538 1-216-815-11 METAL CHIP
R539 1-216-813-11 METAL CHIP
R564 1-216-827-11 METAL CHIP
R567 1-216-845-11 METAL CHIP
R568 1-216-815-11 METAL CHIP
330
220
3.3K
100K
330
220
100
3.3K
100K
330
220
3.3K
100K
330
100K
330
220
100
3.3K
100K
330
220
3.3K
100K
10K
33K
1M
0
1K
100
22
22
22
3.3K
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
35
SCD-XE600
MAIN POWER SWITCH PT
Ref. No.
Part No.
Description
R569 1-216-813-11 METAL CHIP
R701 1-216-821-11 METAL CHIP
R702 1-216-833-11 METAL CHIP
R703 1-216-833-11 METAL CHIP
R707 1-216-821-11 METAL CHIP
R708 1-216-809-11 METAL CHIP
R731 1-216-833-11 METAL CHIP
R752 1-216-864-11 SHORT CHIP
R781 1-216-821-11 METAL CHIP
R782 1-216-841-11 METAL CHIP
R783 1-216-833-11 METAL CHIP
R791 1-216-805-11 METAL CHIP
R804 1-216-815-11 METAL CHIP
R806 1-216-150-11 RES-CHIP
R819 1-216-847-11 METAL CHIP
R820 1-216-847-11 METAL CHIP
R831 1-216-833-11 METAL CHIP
R840 1-216-845-11 METAL CHIP
R846 1-216-842-11 METAL CHIP
R852 1-216-845-11 METAL CHIP
R853 1-216-842-11 METAL CHIP
R857 1-218-883-11 METAL CHIP
R858 1-216-846-11 METAL CHIP
R860 1-216-855-11 METAL CHIP
R861 1-216-850-11 METAL CHIP
R865 1-216-842-11 METAL CHIP
R866 1-216-839-11 METAL CHIP
R869 1-216-842-11 METAL CHIP
R870 1-216-839-11 METAL CHIP
R871 1-216-833-11 METAL CHIP
R872 1-216-833-11 METAL CHIP
R874 1-218-883-11 METAL CHIP
R876 1-216-844-11 METAL CHIP
R877 1-216-853-11 METAL CHIP
R878 1-216-853-11 METAL CHIP
R880 1-216-845-11 METAL CHIP
R885 1-216-835-11 METAL CHIP
R886 1-216-844-11 METAL CHIP
R888 1-216-835-11 METAL CHIP
R889 1-216-864-11 SHORT CHIP
R892 1-218-896-11 METAL CHIP
R893 1-218-896-11 METAL CHIP
R894 1-216-842-11 METAL CHIP
R895 1-216-842-11 METAL CHIP
R897 1-216-853-11 METAL CHIP
R899 1-216-849-11 METAL CHIP
R961 1-216-821-11 METAL CHIP
R962 1-216-821-11 METAL CHIP
R963 1-216-821-11 METAL CHIP
R971 1-216-833-11 METAL CHIP
R972 1-216-833-11 METAL CHIP
R973 1-216-827-11 METAL CHIP
R975 1-216-839-11 METAL CHIP
R976 1-216-809-11 METAL CHIP
R977 1-216-809-11 METAL CHIP
R978 1-216-837-11 METAL CHIP
R979 1-216-833-11 METAL CHIP
33K
56K
33K
10K
10K
33K
82K
470K
470K
100K
10K
100K
56K
100K
56K
33K
120K
680K
270K
56K
10K
0
1K
47K
10K
47
330
10
150K
150K
220
1K
10K
10K
1K
100
1K
1K
1K
10K
10K
3.3K
33K
100
100
22K
10K
15K
82K
15K
0
110K
110K
56K
56K
470K
220K
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
0.5% 1/10W
5% 1/10W
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
Remark Ref. No.
Part No.
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
0.5% 1/10W
5% 1/10W
5%
5%
5%
1/10W
1/10W
1/10W
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
0.5% 1/10W
5% 1/10W
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/8W
1/10W
1/10W
RB301
RB302
RB402
RB410
RB432
RB441 1-233-413-11 RES, CHIP NETWORK
RB442 1-233-413-11 RES, CHIP NETWORK
RB462 1-233-419-21 RES, CHIP NETWORK
RB502 1-233-419-21 RES, CHIP NETWORK
RB532 1-233-419-21 RES, CHIP NETWORK
RB562
RB601
RB602
RB603
RB604
RB605 1-236-908-11 RES, CHIP NETWORK
RB606 1-236-908-11 RES, CHIP NETWORK
RB607 1-236-908-11 RES, CHIP NETWORK
RB609 1-236-908-11 RES, CHIP NETWORK
RB610 1-233-578-11 RES, CHIP NETWORK
RB611
RB612
RB613
RB615
RB616
Description
< COMPOSITION CIRCUIT BLOCK >
1-233-414-11 RES, CHIP NETWORK
1-233-873-21 RES, CHIP NETWORK
1-233-419-21 RES, CHIP NETWORK
1-233-413-11 RES, CHIP NETWORK
1-233-419-21 RES, CHIP NETWORK
1-233-419-21 RES, CHIP NETWORK
1-236-908-11 RES, CHIP NETWORK
1-233-412-11 RES, CHIP NETWORK
1-233-577-11 RES, CHIP NETWORK
1-233-414-11 RES, CHIP NETWORK
1-236-908-11 RES, CHIP NETWORK
1-236-908-11 RES, CHIP NETWORK
1-236-908-11 RES, CHIP NETWORK
1-233-577-11 RES, CHIP NETWORK
1-233-577-11 RES, CHIP NETWORK
RB617 1-233-577-11 RES, CHIP NETWORK
< VIBRATOR >
X321 1-795-535-21 VIBRATOR, CRYSTAL (11.2896MHz)
*************************************************************
1-862-182-11 POWER SWITCH BOARD
********************
Remark
4.7K (3216)
220K (3216)
6.8K (3216)
2.2K (3216)
6.8K (3216)
2.2K (3216)
2.2K (3216)
6.8K (3216)
6.8K (3216)
6.8K (3216)
6.8K (3216)
10K (3216)
1.0K (3216)
470 (3216)
4.7K (3216)
10K (3216)
10K (3216)
10K (3216)
10K (3216)
47K (3216)
10K (3216)
10K (3216)
10K (3216)
470 (3216)
470 (3216)
470 (3216)
5%
5%
5%
1/10W
1/10W
1/10W
0.5% 1/10W
0 C891
< CAPACITOR >
1-113-920-11 CERAMIC 0.0022uF 20% 250V
< CONNECTOR >
* CN891 1-580-230-31 PIN, CONNECTOR (PC BOARD) 2P
0 S891
0 C101
< SWITCH >
1-762-581-11 SWITCH, AC POWER PUSH (1 KEY) (POWER)
*************************************************************
1-862-181-11 PT BOARD
********
< CAPACITOR >
1-113-920-11 CERAMIC
< CONNECTOR >
0.0022uF 20% 250V
* CN101 1-568-226-11 PIN, CONNECTOR (3.96mm PITCH) 2P
*************************************************************
36
The components identified by mark 0 or dotted line with mark 0 are critical for safety.
Replace only with part number specified.
SCD-XE600
RF
Ref. No.
Part No.
Description
A-4750-527-A RF BOARD, COMPLETE
*******************
Remark
< CAPACITOR >
C001 1-107-726-91 CERAMIC CHIP 0.01uF
C002 1-107-726-91 CERAMIC CHIP 0.01uF
10% 16V
10% 16V
C004 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C005 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C006 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C007 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C008 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C009 1-124-779-00 ELECT CHIP 10uF
C011 1-107-726-91 CERAMIC CHIP 0.01uF
20%
10%
16V
16V
C015 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C016 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C017 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C018 1-115-416-11 CERAMIC CHIP 0.001uF
5%
C019 1-164-739-11 CERAMIC CHIP 560PF 5%
C021 1-124-779-00 ELECT CHIP 10uF
25V
50V
20% 16V
C022 1-107-826-11 CERAMIC CHIP 0.1uF
C023 1-126-206-11 ELECT CHIP 100uF
10% 16V
20% 6.3V
C024 1-115-416-11 CERAMIC CHIP 0.001uF
5%
C025 1-107-826-11 CERAMIC CHIP 0.1uF
10%
25V
16V
C026 1-107-726-91 CERAMIC CHIP 0.01uF
10% 16V
C027 1-107-726-91 CERAMIC CHIP 0.01uF
C028 1-107-826-11 CERAMIC CHIP 0.1uF
C031 1-107-826-11 CERAMIC CHIP 0.1uF
C032 1-107-826-11 CERAMIC CHIP 0.1uF
10%
10%
10%
10%
16V
16V
16V
16V
C033 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C034 1-164-227-11 CERAMIC CHIP 0.022uF
10% 25V
C035 1-107-826-11 CERAMIC CHIP 0.1uF
10% 16V
C036 1-165-176-11 CERAMIC CHIP 0.047uF
10% 16V
C038 1-165-176-11 CERAMIC CHIP 0.047uF
10% 16V
C039 1-107-726-91 CERAMIC CHIP 0.01uF
10% 16V
C040 1-164-217-11 CERAMIC CHIP 150PF
C043 1-107-826-11 CERAMIC CHIP 0.1uF
C044 1-124-779-00 ELECT CHIP 10uF
C046 1-107-726-91 CERAMIC CHIP 0.01uF
C047 1-107-826-11 CERAMIC CHIP 0.1uF
5%
10%
20%
10%
10%
50V
16V
16V
16V
16V
C048 1-127-715-11 CERAMIC CHIP 0.22uF
< CONNECTOR >
10%
CN001 1-815-031-11 CONNECTOR, FFC/FPC (ZIF) 24P
CN002 1-784-879-21 CONNECTOR, FFC (LIF (NON-ZIF)) 31P
CN003 1-784-861-21 CONNECTOR, FFC (LIF (NON-ZIF)) 9P
16V
< DIODE >
D001 8-719-988-61 DIODE 1SS355TE-17
D004 8-719-988-61 DIODE 1SS355TE-17
< IC >
L001
L002
< COIL >
1-412-031-11 INDUCTOR
1-412-031-11 INDUCTOR
47uH
47uH
Ref. No.
Part No.
Description
< TRANSISTOR >
Q001 8-729-903-46 TRANSISTOR
Q002 8-729-903-46 TRANSISTOR
< RESISTOR >
2SB1132-P
2SB1132-P
R002 1-216-809-11 METAL CHIP
R003 1-216-809-11 METAL CHIP
R004 1-216-864-11 SHORT CHIP
R005 1-216-845-11 METAL CHIP
R006 1-216-838-11 METAL CHIP
R007 1-216-803-11 METAL CHIP
R008 1-216-803-11 METAL CHIP
R009 1-216-820-11 METAL CHIP
R010 1-216-841-11 METAL CHIP
R011 1-216-809-11 METAL CHIP
R013 1-216-833-11 METAL CHIP
R018 1-216-833-11 METAL CHIP
R020 1-216-803-11 METAL CHIP
R023 1-216-803-11 METAL CHIP
R025 1-216-841-11 METAL CHIP
R029 1-216-809-11 METAL CHIP
R037 1-216-834-11 METAL CHIP
R038 1-216-861-11 METAL CHIP
R045 1-216-813-11 METAL CHIP
R052 1-216-864-11 SHORT CHIP
10K
10K
33
33
47K
100
12K
2.2M
220
0
33
33
820
47K
100
100
100
0
100K
27K
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
Remark
R053 1-216-864-11 SHORT CHIP
R054 1-216-864-11 SHORT CHIP
0
0
R055 1-216-864-11 SHORT CHIP 0
*************************************************************
MISCELLANEOUS
**************
0 6
11
12
0 255
258
1-827-597-11 CORD, POWER
1-829-172-11 WIRE (FLAT TYPE) (31 CORE)
1-828-333-11 WIRE (FLAT TYPE) (13 CORE)
1-478-637-31 DEVICE, OPTICAL (DBU-3)
1-824-106-12 CABLE, FLEXIBLE FLAT (24 CORE)
M151 A-4604-363-A MOTOR (L) ASSY (LOADING)
0 T101
1-443-403-11 TRANSFORMER, POWER
*************************************************************
ACCESSORIESE
*************
1-478-636-11 REMOTE COMMANDER (RM-SX800)
1-790-735-12 CORD, CONNECTION (Audio Connecting Cord)
2-021-059-61 MANUAL, INSTRUCTION
(ENGLISH, TRADITIONAL CHINESE)
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
The components identified by mark 0 or dotted line with mark 0 are critical for safety.
Replace only with part number specified.
37
SCD-XE600
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver.
1.0
Date
2004.10
New
Description of Revision
2
advertisement
Key Features
- Plays Super Audio CDs and standard CDs
- Multi-channel decoding function
- Optical digital output
- Variety of playback modes
- Remote control
- Built-in DAC
- High dynamic range
- Low distortion
- High frequency response
- LCD Display