R&S ZVA Service Manual
Service Manual Instrument
Vector Network Analyzers
R&S® ZVA 8 / ZVA 24 / ZVA 40 / ZVA50 / ZVA67
1145.1110.08/10 / 24/26 / 40/42 / 50/52
1305.7002.02
Test and Measurement
1145.1155.82-05
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of the owners.
The instrument includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/). It
includes cryptographic software written by Eric Young ([email protected]) and software written by Tim Hudson
([email protected]). The verbatim license texts are provided in on the user documentation CD-ROM (included in
delivery).
R&S ZVA
Index
Index
A
F
Alignment ....................................................................... 2.1
Frequency accuracy................................................. 2.4
Frequency response correction ......................... 2.5, 2.7
Level accuracy ......................................................... 2.7
Manual ..................................................................... 2.2
Reference frequency................................................ 2.4
Test equipment ........................................................ 2.2
Front module processor
Function .................................................................3.19
Replacement ..........................................................3.23
Front unit ......................................................................3.18
Frontend
Repelcement .................................................3.51, 3.52
Function description........................................................3.1
B
I
Battery
Replacement.......................................................... 3.26
Block circuit
diagram.................................................................... 5.3
Block diagram
Explanation .............................................................. 3.2
Board replacement
DC/AC converter.................................................... 3.31
Detector A120 ........................................................ 3.57
Disk drive ............................................................... 3.36
Fan ........................................................................ 3.40
Front hood ............................................................. 3.35
Front module processor A90 .................................. 3.23
Frontend A100 .............................................. 3.51, 3.52
LCD ....................................................................... 3.31
Motherboard A10 ................................................... 3.41
MW converter unit A160......................................... 3.59
Power supply ......................................................... 3.39
Power supply ......................................................... 3.38
Switching foil.......................................................... 3.33
Synthesizer A110 ................................................... 3.58
Board Replacement
Battery ................................................................... 3.26
Boards
Overview................................................................ 3.22
Boot problems
Troubleshooting ..................................................... 3.63
Instrument construction ..................................................3.1
K
Keyboard
Function .................................................................3.18
Replacement ..........................................................3.33
L
LC display.....................................................................3.18
LCD
Replacement ..........................................................3.31
Level accuracy
Alignment .................................................................2.7
Lithium battery
Replacement ..........................................................3.26
M
Manual alignment ...........................................................2.2
Mechanische Zeichnungen ...........................................5.33
Menu, service .................................................................2.1
Motherboard
Function .................................................................3.19
Replacement ..........................................................3.41
D
O
Detector
Replacement.......................................................... 3.57
Disk drive
Replacement.......................................................... 3.36
Documents ..................................................................... 5.1
OCXO
Function .................................................................3.11
Option
B4
Function ...........................................................3.11
R&S FSU-B9
Function ...........................................................3.21
Installation ................................................................4.2
List ...........................................................................4.2
F
P
Fan
Replacement.......................................................... 3.40
Frequency accuracy
Alignment................................................................. 2.4
Check ................... 1.5, 1.9, 1.11, 1.12, 1.13, 1.14, 1.15
Frequency response
Correction ......................................................... 2.5, 2.7
Front hood.................................................................... 3.35
1145.1155.82
Password........................................................................2.1
Performance test
Frequency accuracy ........................ 1.5, 1.9, 1.11, 1.12
............................................................. 1.13, 1.14, 1.15
Harmonics suppression ............................................1.6
Level accuracy .........................................................1.7
Level linearity ....................................................1.6, 1.8
Protocol ......................... 1.16, 1.43, 1.76, 1.122, 1.171
I-1
E-5
Index
R&S ZVA
P
S
Performance Test........................................................... 1.1
Power cables ................................................................. 5.1
Power supply
Function ................................................................. 3.19
Replacement.......................................................... 3.39
Replacement.......................................................... 3.38
Power-up problems ...................................................... 3.62
Precision attenuator
Function ....................................... 3.4, 3.5, 3.6, 3.7, 3.8
Software update .............................................................4.1
Spare parts
list of all parts ..............................................................5
Synthesizer
Replacement ..........................................................3.58
T
Test equipment
Alignment .................................................................2.2
Performance test ......................................................1.2
Test equpment
Troubleshooting......................................................3.61
Tracking generator
Function .................................................................3.21
Troubbleshooting
Power-up problems ................................................3.62
Troubleshooting
Boot problems ........................................................3.63
Selftest ..........................................................3.70, 3.75
Selftest ...................................................................3.65
R
Repairs........................................................................... 3.1
Replacement
Boards ................................................................... 3.21
Replacing
Boards ................................................................... 3.21
1093.4820.82
I-2
E-5
R&S ZVA
Service and Repairs
Contents of the Manuals for the ZVA Network Analyzer
Service manual - instrument
This service manual for the instrument contains information on checking specs, instrument alignment, repairs and troubleshooting. The service manual – instrument contains all the information you
will need to repair the instrument by means of board replacement.
The service manual has four chapters and an annex (Chapter 5) which contains the instrument
documentation:
Chapter 1
Contains all the information you will need to check specs and lists the test equipment required.
Chapter 2
Describes the manual alignment of the frequency and DC measurement accuracy, automatic alignment after board replacement and also system error calibration.
Chapter 3
Describes the instrument design and simple repair and troubleshooting strategies. Board replacement plays a key role.
Chapter 4
Contains information on expansions and modifications achieved by updating instrument software and by retrofitting options.
Chapter 5
Describes how to return the instrument and order spare parts. It also contains
spare parts lists and exploded diagrams of the instrument.
Operating manual
The operating manual contains all the information you will need about the technical characteristics of
the instrument, putting the instrument into operation, the basic operating procedures, controls and
displays, menu operation and remote control.
By way of an introduction, typical measurement tasks are explained using menu screen-shots and
program examples.
The operating manual also contains notes on maintenance and explains how to troubleshoot faults
using the warnings and error messages output by the instrument.
1145.1155.82
0.1
E-5
Manuals
R&S ZVA
Service and Repairs
Contact your Rohde & Schwarz Service Center or the Rohde & Schwarz Express Spare-Part Delivery
Service to solve your service problems or to order spare parts and boards.
A list of Rohde & Schwarz representatives and the address of our Express Spare-Part Delivery Service
can be found at the beginning of this service manual.
To help us process your queries rapidly and effectively, and to determine whether your instrument is still
covered by warranty, we need the following information:
• Instrument model
• Serial number
• Firmware version
• If repairs are to be made, the description of the fault should be as accurate as possible
• Contact person to answer any questions that may arise
Rohde & Schwarz offers the following calibration services:
• Calibration on R&S’s own test systems. The calibration documentation meets the requirements
of the ISO 9000 quality management system.
• Calibration in an R&S-based, accredited calibration laboratory. The calibration documentation
comprises the calibration certificate.
The calibration documentation meets the requirements of the ISO 17025 quality management
system.
Chapter 5 describes in detail the procedure for returning your instrument and the procedure for ordering
spare parts.
1145.1155.82
0.2
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test
Table of Contents - Chapter 1 "Performance Test"
1 Performance Test................................................................................................ 1.1
Preliminary Remarks ........................................................................................................................1.1
Test Equipment and Accessories ...................................................................................................1.2
Performance Test .............................................................................................................................1.5
Checking the Frequency Accuracyy.........................................................................................1.5
Checking the Harmonics ..........................................................................................................1.6
Checking the Accuracy of Output Power..................................................................................1.7
Checking the Output Linearity ..................................................................................................1.8
Checking the Power Measurement Accuracyy.........................................................................1.9
Checking the Input Linearity...................................................................................................1.10
Checking the Input Noise Level..............................................................................................1.11
Checking the Matching (raw)..................................................................................................1.12
Checking the Dynamic Range................................................................................................1.13
Checking the Receiver Attenuator (only with Option Receiver Attenuator)..........................1.14
Checking the DC Measurement Inputs ..................................................................................1.15
®
Performance Test Report R&S ZVA8 .........................................................................................1.16
®
Performance Test Report R&S ZVA24 .......................................................................................1.43
®
Performance Test Report R&S ZVA40 .......................................................................................1.76
®
Performance Test Report R&S ZVA50 .....................................................................................1.122
®
Performance Test Report R&S ZVA67 .....................................................................................1.171
1145.1155.82
I-1.1
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test
1 Performance Test
Preliminary Remarks
•
The required characteristics of the network analyzer are checked after a warm-up time of at least
60 minutes; this ensures that the guaranteed data is met.
•
The values stated in the following sections are not guaranteed data; only the specifications in the data
sheet are binding.
•
The values in the data sheet are guaranteed limits. Because of the measurement errors that arise,
these limits must be increased to encompass the tolerances of the measuring equipment used for
the performance test.
•
Entries for the measurement are represented in the following way:
[<KEY>]
Press a front-panel key, e.g. [SPAN]
[<SOFTKEY>] Press a softkey, e.g. [MARKER -> PEAK]
[<nn unit>]
Enter a value + terminate the entry with a unit, e.g. [12 kHz]
#
Represents the number of the PORT under test, e.g. 1 for PORT 1.
Consecutive entries are separated with a [ : ], e.g. [ Meas Bandwidth : 1 kHz]
1145.1155.82
1.1
E-5
Test Equipment and Accessories
R&S ZVA
Test Equipment and Accessories
Item
Type of
equipment
Recommended characteristics or
features
Recommended
model
1
Spectrum
analyzer
a) Counter mode:
Min. resolution: 100 Hz
Max. rel. frequency deviation: 10-6
b) Linearity
Max. departure from linearity (2 ):
0.06 dB
c) Frequency response:
50 MHz to 4 GHz: < 1 dB
4 GHz to 8 GHz: < 1.5 dB
8 GHz to 22 GHz: < 2 dB
22 GHz to 40 GHz: < 2.5 dB
40 GHz to 50 GHz: < 3 dB
R&S FSU 26
R&S FSU 40
R&S FSU 50
R&S
Order No.
Application
Frequency accuray
Harmonics
Output linearity
Input linearity
R&S FSU 67
R&S NRP
+ Sensor
Max output power
Accuracy of output power
Power measurement
accuray
300 kHz to 8 GHz
R&S NRP-Z51
Max output power
Accuracy of output power
Power measurement
accuray
on R&S ZVA8
Power sensor
10 MHz to 24 GHz
R&S NRP-Z52
Max output power
Accuracy of output power
Power measurement
accuray
on R&S R&S ZVA24
3
Power sensor
10 MHz to 40 GHz
R&S NRP-Z55
Max output power
Accuracy of output power
Power measurement
accuray
on R&S ZVA40
3
Power sensor
10 MHz to 50 GHz
R&S NRP-Z56
Max output power
Accuracy of output power
Power measurement
accuray
on R&S ZVA50
3
Power sensor
10 MHz to 67 GHz
R&S NRP-Z57
Max output power
Accuracy of output power
Power measurement
accuray
on R&S ZVA67
4
Calibration kit
N, 50
R&S ZV-Z270
5011.6536.02 Input linearity
Matching port 1 to port 4
Input noise level
on R&S ZVA8
4
Calibration kit
3.5mm, 50
, DC to 26.5 GHz
R&S ZV-Z235
5011.6542.02 Input linearity
Matching port 1 to port 4
Input noise level
on R&S ZVA24
4
Calibration kit
2.92 mm, 50
, DC to 40 GHz
R&S ZV-Z229
5011.6559.02 Input linearity
Matching port 1 to port 4
Input noise level
on R&S ZVA40
4
Calibration kit
2.4 mm, 50
R&S ZV-Z224
5011.6565.02 Input linearity
Matching port 1 to port 4
Input noise level
on R&S ZVA40 and
R&S ZVA50
2
Power meter
3
Power sensor
3
1145.1155.82
, DC to 18 GHz
, DC to 50 GHz
1.2
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test
Item
Type of
equipment
Recommended characteristics or
features
Recommended
model
R&S
Order No.
Application
4
Calibration kit
1.85 mm, 50
R&S ZV-Z218
5011.6571.02
Input linearity
Matching port 1 to port 4
Input noise level
on R&S ZVA67
5
Signal
generator
300 kHz to 40 GHz,
Power = -40 dBm to 10 dBm
R&S SML01
R&S SMR40
with Option
R&S SMR-B17
1090.3000.11 Power measurement
1104.0002.40 accuray
, 10 MHz to 67 GHz
1104.5233.02
5
Signal
generator
40 GHz to 50 GHz,
Power = -40 dBm to 00 dBm
R&S SMR50
with Option
R&S SMR-B18
1134.9008.50 Power measurement
accuray on R&S ZVA50
1135.2907.02 (40 to 50GHz)
6
Power splitter
N, 50 Ohm,
eq < 0.05 (50 MHz to 8 GHz)
Output tracking < 0.15 dB
Weinschel 1870A
-
Power measurement
accuray
5
Power splitter
3.5mm, 50 Ohm,
Output tracking < 0.25 dB
Weinschel 1593
-
Recording correction
values on R&S ZVA24
6
Power splitter
2.92mm, 50 Ohm,
Output tracking < 0.5 dB
Weinschel 1534
-
Power measurement
accuray
on R&S R&S ZVA40
6
Power splitter
1.85mm, 50 Ohm,
Output tracking < 0.5 dB
Anritsu SC6778
-
Power measurement
accuray
on R&S R&S ZVA50
7
Test cable
Test cable N (m) to N (m).
R&S ZV-Z11
1085.6505.03 Frequency uncertainty
Harmonics
Matching port 1 to port 4
Power measurement
accuray
on R&S ZVA8
7
Test cable
Test cable 3.5 mm (m) to 3.5 mm (f)
R&S ZV-Z14
1134.4093.02 Frequency uncertainty
Harmonics
Matching port 1 to port 4
Power measurement
accuray
on R&S ZVA24
7
Test cable
Test cable 2.92 mm (f) to 2.92 mm (f)
-
Frequency uncertainty
Harmonics
Matching port 1 to port 4
Power measurement
accuracy
on R&S ZVA40
-
Frequency uncertainty
Harmonics
Matching port 1 to port 4
Power measurement
accuracy
on R&S ZVA40
-
Frequency uncertainty
Harmonics
Matching port 1 to port 4
Power measurement
accuracy
on R&S ZVA40 and R&S
ZVA50
-
Power measurement
accuracy
on R&S ZVA40 and
R&S ZVA50
Order No. 23005066
Huber & Suhner
7
Test cable
Test cable 2.92 mm (m) to 2.92mm
(f)
Order No. 23005070
Huber & Suhner
7
Test cable
Test cable 2.4 mm (f) to 2.4mm (f)
Order No.
Huber & Suhner
7
Test cable
Test cable 2.4mm (m) to 2.4mm (f)
Order No.
Huber & Suhner
1145.1155.82
1.3
E-5
Test Equipment and Accessories
R&S ZVA
Item
Type of
equipment
Recommended characteristics or
features
Recommended
model
R&S
Order No.
7
Test cable
Test cable 1.85 mm (f) to 1.85mm (f)
R&S ZV-Z97
1301.7637.25 Frequency uncertainty
Harmonics
Matching port 1 to port 4
Power measurement
accuracy
on R&S ZVA67
7
Test cable
Test cable 1.85mm (f) to 1.85mm (m) GORE
EN0CB0CB0240
8
BNC cable
Male – male, approx. 1.5 m
9
DC power
supply
-12 V to +12 V
R&S NGSM
32/10
0192.0810.31
DC meas inputs
10
Multimeter
MU < 0.2%,
DC range 1 V, 10 V
R&S URE3
0350.5315.03
DC meas inputs
11
Conn. Cables
for DC inputs
R&S ZV-Z71
1164.1005.02
DC meas inputs
1145.1155.82
-
Application
Power measurement
accuracy
on R&S ZVA67
General:
Device synchronisation
1.4
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test
Performance Test
Compare with data sheet
Checking the Frequency Accuracyy
Instrument:
Spectrum analyzer (see Chapter “Test Equipment“, Item1)
Test cable (see Chapter “Test Equipment“, Item7)
Test setup:
Connect the spectrum analyzer to port 1
Spectrum analyzer settings:
- [ PRESET ]
- [ FREQ : 1 GHz ]
- [ SPAN : 100 kHz ]
- [ BW : MANUAL RES BW : 2 kHz ]
- [ MARKER : MARKER MODE : FREQ COUNT ]
- [ AMPT : REF LEVEL : 10 dBm]
R&S® ZVA settings
- Select [System : Internal Reference]
- [ Preset ]
- [ Meas :Wave Quantities: a1 Src Port 1]
- [ Sweep : Sweep Type : CW Mode :
CW Frequency : 1 GHz; Power : 0 dBm]
- [ Sweep : Single : Restart]
Measurement:
Read off the frequency indicated by the marker.
Frequency deviation = marker value – 1 GHz
Max. frequency deviation .............................. see Performance Test Report
1145.1155.82
1.5
E-5
Performance Test
R&S ZVA
Checking the Harmonics
Instrument:
Spectrum analyzer (see Chapter "Test Equipment", Item1)
Test cable (see Chapter “Test Equipment", Item7)
Test setup:
Connect the spectrum analyzer to port#
Spectrum analyzer settings:
Note:
Synchronize the reference oscillators in the spectrum analyzer and in the
R&S®ZVA.
- [ PRESET ]
- [ FREQ : fGEN, 2* fGEN, 3* fGEN *]
- [ SPAN : ZERO SPAN ]
- [ BW : MANUAL RES BW : 1 kHz ]
- [ MARKER : DETECTOR : RMS ]
- [ AMPT : REF LEVEL : 13 dBm]
* For measurement frequencies, see Performance Test Report {fGEN}.
R&S® ZVA settings:
- [ Preset ]
- [ Meas : Wave Quantities: a# Src Port # ]
- [ Sweep : Sweep Type : CW Mode :
CW Frequency : {fGEN*} ; Power : 10 dBm ]
- [ Sweep : Single : Restart]
* For measurement frequencies, see Performance Test Report {fGEN}.
Measurement:
Calculation:
Read off the levels Ln*fgen (n = 1, 2, 3) indicated by the spectrum
analyzer’s markers.
Harmonics = Ln*f gen - Lfgen - cable loss (in dB)
The cable loss corresponds to the S21 of the test cable used between the
fundamental and the measured harmonic (S21 is negative).
1145.1155.82
1.6
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test
Checking the Accuracy of Output Power
Instrument:
Power sensor or
Power meter with power sensor
(see Chapter “Test Equipment“, Item2)
Test setup:
Connect the power sensor to port #
Power sensor settings:
For measurement frequencies, see Performance Test Report {fGEN*}.
R&S®ZVA settings:
- [ Preset ]
- [ Meas :Wave Quantities: a# Src Port # ]
- [ Sweep : Sweep Type : CW Mode :
CW Frequency : {fGEN*} ; Power : -10 dBm]
- [ Mode : ALC : On]
- [ Sweep : Single : Restart]
* For measurement frequencies, see Performance Test Report {fGEN}.
Measurement:
Read off the levels indicated by the power sensor
Level deviation = LSENSOR – (-10 dBm)
1145.1155.82
1.7
E-5
Performance Test
R&S ZVA
Checking the Output Linearity
Instrument:
Spectrum analyzer (see Chapter “Test Equipment“, Item1)
Test cable (see Chapter “Test Equipment“, Item7)
Test setup:
Connect the spectrum analyzer to port #
Spectrum analyzer settings:
Note:
Synchronize the reference oscillators in the spectrum analyzer and in the
R&S®ZVA :
- [ PRESET ]
- [ FREQ : fGEN*]
- [ SPAN : ZERO SPAN ]
- [ BW : MANUAL RES BW : 1 kHz ]
- [ MARKER : DETECTOR : RMS ]
- [ AMPT : REF LEVEL :15 dBm]
In case of optional generator step attenuators:
If ZVAB source level value < -25 dBm
- [ AMPT : RF ATTEN : 5 dB]
- [ AMPT : REF LEVEL : -20 dBm ]
* For measurement frequencies, see Performance Test Report {fGEN}.
R&S®ZVA settings:
- [ Preset ]
- [ Meas : Wave Quantities: a# Src Port # ]
- [ Sweep : Sweep Type : CW Mode :
CW Frequency : {fGEN*} ; Power : {lGEN*}]
- [ Mode : ALC : On]
- [ Sweep : Single : Restart]
* For measurement frequencies {fGEN} and levels {lGEN}, see
Performance Test Report
Measurement:
Calculation:
Read the spectrum analyzer’s marker values (level L) .
The measured values are referred to the level at the ZVA setting of
-10 dBm.
Calculating the generator level linearity:
Level linearity = L - [email protected] – step width (in dB)
Step width = lgen – (-10 dBm) (reference)
1145.1155.82
1.8
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test
Checking the Power Measurement Accuracyy
Instrument:
Power sensor or
Power meter with power sensor
(see Chapter “Test Equipment“, Item2)
Signal generator (see Chapter “Test Equipment“, Item5)
Power splitter (see Chapter “Test Equipment“, Item6)
Calibration kit (see Chapter “Test Equipment“, Item4)
Test cable (see Chapter “Test Equipment“, Item7)
Preparation/
test setup:
Connect the signal generator to the power-splitter input using the test
cable.
Connect the power sensor to a power-splitter output
Connect the other power-splitter output to port# using an adapter from the
calibration kit
R&S®ZVA settings:
The reference oscillators in the signal generator and in the ZVA must be
synchronized.
- [ Preset ]
- [ Meas : Wave Quantities: b# Src Port # ]
- [ Power : RF Off ]
- [ Meas Bandwidth : 100 Hz ]
- [ Marker ]
- [ Sweep : Sweep Type : CW Mode :
CW Frequency : {fGEN*}]
- [ Sweep : Single : Restart]
* For the measurement frequencies, see Performance Test Report
{fGEN}.
Measurement:
Signal generator : CW Mode, Frequency: fgen
Signal-generator level: -5 dBm
Adjust the signal-generator level so that the power meter
reads 0 dB +/- 0.2 dB
Read off the power meter display and the ZVA marker values.
Level error = LZVA – LPS
In case of optional receiver
step attenuators further
R&S® ZVAB settings:
In case of optional receiver
step attenuators further
measurement:
1145.1155.82
- [ PRESET]
- [ MEAS : WAVE QUANTITIES : b# SRC PORT #
- [ TRACE FUNCT: DATA
MEM : MATH = DATA / MEM]
- [ POWER: STEP ATTENUATORS: b#: 5 dB]
- [ POWER: STEP ATTENUATORS: b#: 15 dB]
- [ POWER: STEP ATTENUATORS: b#: 35 dB]
Read out math trace.
1.9
E-5
Performance Test
R&S ZVA
Checking the Input Linearity
Instrument:
Calibration kit (see Chapter “Test Equipment“, Item4)
R&S®ZVA settings:
- [ Preset ]
- [ Meas : Ratios: b#/a# Src Port #]
- [ Meas Bandwidth : 10 Hz ]
- [ Marker]
- [ Sweep : Sweep Type : Power : Start -40dBm : Stop 10dBm :
CW Frequency : {fGEN*}]
- [ Sweep : Single : Restart]
* For measurement frequencies, see Performance Test Report {fGEN}
1. Test setup:
Connect an open male to port #
1. Measurement:
- [ Trace Funct ]
- [ Data -> Mem ]
- [ Show Mem : off ]
2. Test setup:
Connect a short male to port #
2. Measurement:
- [ Math = Data/Mem : on ]
Set
Ref Marker to -10dBm
Select Delta Mode
Set
Marker1 to -40dBm up to +10dBm by 5dB steps
Read off the differences of the Marker Values displayed by the ZVA
1145.1155.82
1.10
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test
Checking the Input Noise Level
Test equipment:
Calibration kit
(see Chapter “Test Equipment“, Item4)
Test setup:
Connect the Match Male from the calibration kit to port #
R&S®ZVA settings:
- [ Preset ]
- [ Meas : Wave Quantities: b# Src Port # ]
- [ Power : RF Off ]
- [ Meas Bandwidth : 10 Hz ]
- [ Marker ]
- [ Sweep : Sweep Type : CW Mode : CW Frequency : {fGEN*}]
- Service Function 1.0.0.1.1 (see chapter 3 ‘Service Functions’, Service
Level 2)
- [ Measure : Wave Quantities : More Wave Quantities… : Properties :
Detector : RMS : Meas. Time: 500ms ]
- [ Sweep : Single : Restart]
* For measurement frequencies, see Performance Test Report {fGEN}.
Measurement:
1145.1155.82
Read off the noise level indicated by the markers on the DUT.
1.11
E-5
Performance Test
R&S ZVA
Checking the Matching (raw)
Instrument:
Calibration kit (see Chapter “Test Equipment“, Item4)
Test cable (see Chapter “Test Equipment“, Item7)
R&S®ZVA settings:
- [ Preset ]
- [ Power : 0 dBm ]
1. Preparation/
test setup:
Connect the test cable to port 1 on the R&S®ZVA and perform a 1-port
calibration at the end of the cable.
Connect the end of the test cable to port 2 (port 3, port4) on the
R&S®ZVA.
R&S®ZVA settings:
- [ Meas : S11]
- [ Marker ]
- [ Add Channnel + Trace ]
- [ Meas : S22 (S33, S44) ]
- [ Power : -40 dBm ]
- [ Trace Funct ]
- [ Show Data : off ]
- [ Trace Select : Trc 1 ]
1. Measurement
Read off the network analyzer’s marker values (for marker frequencies
see Performance Test Report)
R&S®ZVA settings:
- [ Power : -40 dBm ]
- [ Trace Funct ]
- [ Show Data : off ]
- [ Trace Select : Trc 2 ]
- [ Trace Funct ]
- [ Show Data : on ]
- [ Meas : S22]
- [ Marker ]
2. Preparation/ test setup:
Set port 2 power to 0 dBm
Connect the test cable to port 2 on the R&S®ZVA and perform a 1-port
calibration at the end of the cable.
Connect the end of the test cable to port 1 on the R&S®ZVA.
2. Measurement
1145.1155.82
Read off the network analyzer’s marker values (for marker frequencies
see Performance Test Report)
1.12
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test
Checking the Dynamic Range
Test equipment:
Calibration kit N
(see Chapter “Test Equipment“, Item4)
Test setup:
Connect Short Male to port1 and port 2 (port 3 and port 4)
(use Short Female with Through Male as a second Short Male)
R&S®ZVA settings:
- [ Preset ]
- [ Meas : Ratios : b1/a2 Src Port 2]
[ Meas : Ratios : b2/a1 Src Port 1]
[ Meas : Ratios : b3/a4 Src Port 4]
[ Meas : Ratios : b4/a3 Src Port 3]
- [ Power : Max. spec. Power ]
- [ Meas Bandwidth : 10 Hz ]
- [ Marker ]
- [ SWEEP : NUMBER OF POINTS : 201 (ZVB4)]
201 (ZVB8)]
301 (ZVB20)]
351 (ZVA24)]
701 (ZVA40)]
851 (ZVA50)]
1001 (ZVA67)]
- [ Sweep : Sweep Type : CW Mode : CW Frequency : {fGEN*}]
- [ Measure : Wave Quantities : More Wave Quantities… : Properties :
Detector : RMS Meas Time: 1 s (R&S ZVA8), 0.5 s (R&S ZVA24,
R&S ZVA40, R&S ZVA50, R&S ZVA67)]
- [ Sweep : Single : Restart]
* For measurement frequencies, see Performance Test Report {fGEN}.
Measurement:
Read off marker value
Calculation:
Dynamic range = Marker value + Power value
1145.1155.82
1.13
E-5
Performance Test
R&S ZVA
Checking the Receiver Attenuator
(only with Option Receiver Attenuator)
Test equipment:
Calibration kit N
(see Chapter “Test Equipment“, Item4)
Test setup:
Connect Short Male to port#
R&S®ZVA settings:
- [ Preset ]
- [ Meas : Wave Quantities : b#/ Src Port #]
- [ Power : 0 dBm ]
- [ Meas Bandwidth : 100 Hz ]
- [Trace Funct : Data -> Mem : Math = Data/Mem : Show Mem off]
- [Pwr BW AVG : Receiver Step Atten : Port # {a Rec Att}*]
- [Trace Funct : Shift Response Value : Magnitude { -a Rec Att}]
- [Marker]
* For attenuator settings {a Rec Att}, see Performance Test Report.
Measurement:
1145.1155.82
Read off the network analyzer’s marker values (for marker frequencies
see Performance Test Report)
1.14
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test
Checking the DC Measurement Inputs
Test equipment:
DC Power Supply NGSM 32/10 (see Chapter “Test Equipment“, Item9)
Multimeter URE3 (see Chapter “Test Equipment“, Item10)
DC cable (see Chapter “Test Equipment“, Item11)
Test setup:
Connect the Power Supply to the Input DC MEAS 1V (DC MEAS 10V) of
the ZVA using the DC cable
R&S®ZVA settings:
- [ Preset ]
For DC Meas 1 V:
- [ Meas : More : DC Inputs : DC Meas ±1 V]
- [ Format : Real]
- [ Scale : Scale/Div : .25 x1]
- [ Marker ]
For DC Meas 10 V:
- [ Meas : More : DC Inputs : DC Meas ±10 V]
- [ Format : Real]
- [ Scale : Scale/Div : 2.5 x1]
- [ Marker ]
Measurement:
Set Power Supply to DC values UDC using Multimeter URE (DC values
see Performance Test Report) and connect it to pos. and neg. input
Read off the DC level UDC ZVA indicated by the marker.
Calculation:
1145.1155.82
Deviation = UDC - UDC ZVA
1.15
E-5
Performance Test Report R&S® ZVA8
R&S ZVA
Performance Test Report R&S® ZVA8
ROHDE&SCHWARZ
Vector Network Analyzer 8 GHz, _ ports
R&S® ZVA8
1145.1110K__
Serial number:
Date:
Person responsible:
Signature:
Parameter
Frequency deviation
@ 1 GHz
With Option ZVAB-B4
1145.1155.82
Reference
Min. value
Actual value
Max. value
Page 1.5
- 8000
_________
- 100
Unit
Measurement
uncertainty
Hz
1 Hz
+ 8000
+ 100
1.16
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Harmonics
Source power +10dBm
Freq.
Harmonics
50 MHz 100 MHz
150 MHz
Performance Test Report R&S® ZVA8
Reference
Min. value
Actual value
Max. value
Page 1.5
________
________
-20
-20
100 MHz 200 MHz
300 MHz
________
________
-20
-20
200 MHz 400 MHz
600 MHz
________
________
-20
-20
500 MHz 1000 MHz
1500 MHz
________
________
-20
-20
750 MHz 1500 MHz
2250 MHz
________
________
-20
-20
1 GHz
________
________
-20
-20
1.5 GHz 3 GHz
4.5 GHz
________
________
-20
-20
2 GHz
________
________
-20
-20
2.1 GHz 4.2 GHz
6.3 GHz
________
________
-20
-20
2.5 GHz 5.0 GHz
7.5 GHz
________
________
-20
-20
3.0 GHz 6.0 GHz
9.0 GHz
________
________
-20
-20
3.5 GHz 7 GHz
10.5 GHz
________
________
-20
-20
4.0 GHz
________
________
-20
-20
4.1 GHz 8.2 GHz
12.3 GHz
________
________
-20
-20
5.0 GHz 10.0 GHz
15.0 GHz
________
________
-20
-20
2 GHz
3 GHz
4 GHz
6 GHz
8.0 GHz
12.0 GHz
Unit
Measurement
uncertainty
dBc
1 dB
Source power +8dBm
1145.1155.82
1.17
E-5
Performance Test Report R&S® ZVA8
Parameter
Reference
Port __
Harmonics
Page 1.5
Min. value
R&S ZVA
Actual value
Max. value
Freq.
Harmonics
5.04 GHz 10.08 GHz
15.12 GHz
________
________
-20
-20
5.05 GHz 10.10 GHz
15.15 GHz
________
________
-20
-20
5.5 GHz 11.0 GHz
16.5 GHz
________
________
-20
-20
6.0 GHz 12.0 GHz
18.0 GHz
________
________
-20
-20
6.35 GHz 12.70 GHz
19.05 GHz
________
________
-20
-20
7.0 GHz 14.0 GHz
21.0 GHz
________
________
-20
-20
8.0 GHz 16.0 GHz
24.0 GHz
________
________
-20
-20
1145.1155.82
1.18
Unit
Measurement
uncertainty
dBc
2 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power Accuracy
Output power -10 dBm
Test frequency:
300 kHz
1 MHz
2 MHz
5 MHz
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
1145.1155.82
Performance Test Report R&S® ZVA8
Reference
Min. value
Actual value
Max. value
Page 1.7
-2
-2
-2
-2
-2
-2
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.19
Unit
Measurement
uncertainty
dB
0.2 dB
2
2
2
2
2
2
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
E-5
Performance Test Report R&S® ZVA8
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Freq.
Level
51 MHz 23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
500MHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
2 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.20
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Freq.
Level
2.1 GHz 23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
Performance Test Report R&S® ZVA8
Reference
Min. value
Actual value
Max. value
Page 1.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
3 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
4 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
4.1 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.21
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA8
Parameter
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Freq.
Level
6 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
8 GHz
18 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
1145.1155.82
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
________
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.22
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Freq.
Level
51 MHz 22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
500MHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
1145.1155.82
Performance Test Report R&S® ZVA8
Reference
Min. value
Actual value
Max. value
Page 1.8
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1.23
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA8
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Freq.
Level
1 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
2 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
1145.1155.82
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1.24
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Freq.
Level
2.1 GHz 22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
3 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
1145.1155.82
Performance Test Report R&S® ZVA8
Reference
Min. value
Actual value
Max. value
Page 1.8
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1.25
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA8
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Freq.
Level
4 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
4.1 GHz
19 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
1145.1155.82
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1.26
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Freq.
Level
6 GHz
19 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
8 GHz
17 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
1145.1155.82
Performance Test Report R&S® ZVA8
Reference
Min. value
Actual value
Max. value
Page 1.8
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1.27
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA8
Parameter
Port __
Power measurement
uncertainty
Test frequency:
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1 GHz
1.5 GHz
2 GHz
2.1 GHz
2.5 GHz
3 GHz
3.5 GHz
4 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
1145.1155.82
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.9
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.28
Unit
Measurement
uncertainty
dB
0.3 dB
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA8
Parameter
Reference
Port __
Input linearity
Reference –10 dBm
Frequ.
Level
50 MHz 20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
Page 1.10
Min. value
Actual value
Max. value
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
________
________
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
500 MHz 20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
________
________
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
4 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
________
________
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
4.1 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
________
________
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
1145.1155.82
1.29
Unit
Measurement
uncertainty
dB
0.01 dB
E-5
Performance Test Report R&S® ZVA8
Parameter
Reference
Port __
Input linearity
Reference –10 dBm
Frequ.
Level
8 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
Page 1.10
1145.1155.82
Min. value
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
R&S ZVA
Actual value
________
________
________
________
________
________
________
________
________
________
1.30
Max. value
Unit
Measurement
uncertainty
dB
0.01 dB
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA8
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(without opt. rec atten.
and dir. gen/rec access
Test frequency:
423 kHz
1.12 MHz
2.12 MHz
5.12 MHz
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.31
–100
–100
–100
–100
–100
–100
–100
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA8
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(with opt. rec attenuator)
Test frequency:
423 kHz
1.12 MHz
2.12 MHz
5.12 MHz
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.32
–99
–99
–99
–99
–99
–99
–99
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA8
Parameter
Reference
Port __
Input noise level
(with opt. dir. gen/rec access)
Page 111
Test frequency:
423 kHz
1.12 MHz
2.12 MHz
5.12 MHz
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
1145.1155.82
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.33
–98
–98
–98
–98
–98
–98
–98
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA8
Parameter
Reference
Port __
Input noise level
(with opt. rec. atten. and opt.
Page 111
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
dir. gen/rec access)
Test frequency:
423 kHz
1.12 MHz
2.12 MHz
5.12 MHz
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.34
–97
–97
–97
–97
–97
–97
–97
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA8
Parameter
Reference
Port __
Matching (raw)
Page 1.12
Test frequency:
300 kHz
1 MHz
2 MHz
5 MHz
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.5 GHz
5.0 GHz
5.5 GHz
6.0 GHz
6.5 GHz
7.0 GHz
7.5 GHz
8.0 GHz
1145.1155.82
Min. value
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
14
14
Actual value
Max. value
Unit
Measurement
uncertainty
dB
1 dB
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.35
E-5
Performance Test Report R&S® ZVA8
Parameter
Reference
Port __ to Port __
Dynamic range
Page 1.13
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(without options step
attenuator and direct
generator/receiver access)
Test frequency:
303 kHz
1.12 MHz
2.12 MHz
5.12 MHz
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
3.99988 GHz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
6.99988 GHz
7.50012 GHz
7.99988 GHz
1145.1155.82
100
100
100
100
100
100
120
130
130
130
130
130
130
130
130
130
130
130
130
130
125
125
125
125
125
125
125
125
125
120
120
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.36
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA8
Parameter
Reference
Port __ to Port __
Dynamic range
Page 1.13
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with option generator or
receiver attenuator)
Test frequency:
303 kHz
1.12 MHz
2.12 MHz
5.12 MHz
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
3.99988 GHz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
6.99988 GHz
7.50012 GHz
7.99988 GHz
1145.1155.82
99
99
99
99
99
99
119
129
129
129
129
129
129
129
129
129
129
129
129
129
124
124
124
124
124
124
124
124
124
119
119
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.37
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
E-5
Performance Test Report R&S® ZVA8
Parameter
Reference
Port __ to Port __
Dynamic range
Page 1.13
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with option generator and
receiver attenuator or with
option direct
generator/receiver access)
Test frequency:
303 kHz
1.12 MHz
2.12 MHz
5.12 MHz
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
3.99988 GHz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
6.99988 GHz
7.50012 GHz
7.99988 GHz
1145.1155.82
98
98
98
98
98
98
118
128
128
128
128
128
128
128
128
128
128
128
128
128
123
123
123
123
123
123
123
123
123
118
118
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.38
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA8
Parameter
Reference
Port __ to Port __
Dynamic range
Page 1.13
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with options generator
attenuator or receiver
attenuator and option direct
generator/receiver access)
Test frequency:
303 kHz
1.12 MHz
2.12 MHz
5.12 MHz
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
3.99988 GHz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
6.99988 GHz
7.50012 GHz
7.99988 GHz
1145.1155.82
97
97
97
97
97
97
117
127
127
127
127
127
127
127
127
127
127
127
127
127
122
122
122
122
122
122
122
122
122
117
117
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.39
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
E-5
Performance Test Report R&S® ZVA8
Parameter
Reference
Port __ to Port __
Dynamic range
Page 1.13
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with options generator
attenuator and receiver
attenuator and direct
generator/receiver access)
Test frequency:
303 kHz
1.12 MHz
2.12 MHz
5.12 MHz
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
3.99988 GHz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
6.99988 GHz
7.50012 GHz
7.99988 GHz
1145.1155.82
96
96
96
96
96
96
116
126
126
126
126
126
126
126
126
126
126
126
126
126
121
121
121
121
121
121
121
121
121
116
116
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.40
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Receiver Step Atten.
Attenuation Accuracy
Reference 0 dB
Performance Test Report R&S® ZVA8
Reference
Min. value
Actual value
Max. value
Page 1.14
Atten.
5 dB
Frequ.
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
2
2
2
2
2
2
10 dB
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
2
2
2
2
2
2
20 dB
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
2
2
2
2
2
2
35 dB
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
2
2
2
2
2
2
1145.1155.82
1.41
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA8
Parameter
Reference
Accuracy
DC meas 1 V
Page 1.15
Min. value
R&S ZVA
Actual value
Max. value
Pos. Input
-1000 m V
-300 mV
-10 mV
10 mV
300 mV
1000 m V
- 27.5
- 10.0
- 2.75
- 2.75
- 10.0
- 27.5
________
________
________
________
________
________
+ 27.5
+ 10.0
+ 2.75
+ 2.75
+ 10.0
+ 27.5
Neg. Input
-1000 m V
-300 mV
-10 mV
10 mV
300 mV
1000 m V
- 27.5
- 10.0
- 2.75
- 2.75
- 10.0
- 27.5
________
________
________
________
________
________
+ 27.5
+ 10.0
+ 2.75
+ 2.75
+ 10.0
+ 27.5
Accuracy
DC meas 10 V
Page 1.15
Pos. Input
-10.0 V
-3.0 V
-0.1 V
0.1 V
3.0 V
10.0 V
- 0.275
- 0.10
- 0.0275
- 0.0275
- 0.10
- 0.275
________
________
________
________
________
________
+ 0.275
+ 0.10
+ 0.0275
+ 0.0275
+ 0.10
+ 0.275
Neg. Input
-10.0 V
-3.0 V
-0.1 V
0.1 V
3.0 V
10.0 V
- 0.275
- 0.10
- 0.0275
- 0.0275
- 0.10
- 0.275
________
________
________
________
________
________
+ 0.275
+ 0.10
+ 0.0275
+ 0.0275
+ 0.10
+ 0.275
1145.1155.82
1.42
Unit
Measurement
uncertainty
mV
1 mV
V
0.01 V
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA24
Performance Test Report R&S® ZVA24
ROHDE&SCHWARZ
Vector Network Analyzer, 24 GHz, _ ports
R&S® ZVA24
1145.1110K__
Serial number:
Date:
Person responsible:
Signature:
Parameter
Frequency deviation
@ 1 GHz
With Option ZVAB-B4
1145.1155.82
Reference
Min. value
Actual value
Max. value
Page 1.5
- 8000
_________
- 100
Unit
Measurement
uncertainty
Hz
1 Hz
+ 8000
+ 100
1.43
E-5
Performance Test Report R&S® ZVA24
Parameter
Port __
Harmonics
Source power +10dBm
Freq.
Harmonics
50 MHz 100 MHz
150 MHz
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.5
________
________
-20
-20
100 MHz 200 MHz
300 MHz
________
________
-20
-20
200 MHz 400 MHz
600 MHz
________
________
-20
-20
500 MHz 1000 MHz
1500 MHz
________
________
-20
-20
750 MHz 1500 MHz
2250 MHz
________
________
-20
-20
1 GHz
________
________
-20
-20
1.5 GHz 3 GHz
4.5 GHz
________
________
-20
-20
2 GHz
________
________
-20
-20
2.1 GHz 4.2 GHz
6.3 GHz
________
________
-20
-20
2.5 GHz 5.0 GHz
7.5 GHz
________
________
-20
-20
3.0 GHz 6.0 GHz
9.0 GHz
________
________
-20
-20
3.5 GHz 7 GHz
10.5 GHz
________
________
-20
-20
4.0 GHz 8.0 GHz
12.0 GHz
________
________
-20
-20
4.1 GHz 8.2 GHz
12.3 GHz
________
________
-20
-20
5.0 GHz 10.0 GHz
15.0 GHz
________
________
-20
-20
2 GHz
3 GHz
4 GHz
6 GHz
1145.1155.82
1.44
Unit
Measurement
uncertainty
dBc
1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __
Harmonics
Freq.
Harmonics
Page 1.5
Min. value
Actual value
Max. value
5.04 GHz 10.08 GHz
15.12 GHz
________
________
-20
-20
5.05 GHz 10.10 GHz
15.15 GHz
________
________
-20
-20
5.5 GHz 11.0 GHz
16.5 GHz
________
________
-20
-20
6.0 GHz 12.0 GHz
18.0 GHz
________
________
-20
-20
6.35 GHz 12.70 GHz
19.05 GHz
________
________
-20
-20
7.0 GHz 14.0 GHz
21.0 GHz
________
________
-20
-20
8.0 GHz 16.0 GHz
24.0 GHz
________
________
-20
-20
8.1 GHz 16.2 GHz
24.3 GHz
________
________
-20
-20
9.0 GHz 18.0 GHz
27.0 GHz
________
________
-20
-20
10.0 GHz 20.0 GHz
30.0 GHz
________
________
-20
-20
10.2 GHz 20.4 GHz
30.6 GHz
________
________
-20
-20
11.0 GHz 22.0 GHz
33.0 GHz
________
________
-20
-20
12.7 GHz 25.4 GHz
38.1 GHz
________
________
-20
-20
13.0 GHz 26.0 GHz
39.0 GHz
________
________
-20
-20
14.0 GHz 28.0 GHz
42.0 GHz
________
________
-20
-20
1145.1155.82
1.45
Unit
Measurement
uncertainty
dBc
2 dB
E-5
Performance Test Report R&S® ZVA24
Parameter
Port __
Harmonics
Source power +10
dBm
Freq.
Harmonics
14.6 GHz 29.2 GHz
43.8 GHz
15.0 GHz 30.0 GHz
45.0 GHz
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.5
________
________
-20
-20
________
________
-20
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
Unit
Measurement
uncertainty
dBc
2 dB
16.0 GHz 32.0 GHz
17.0 GHz 34.0 GHz
18.0 GHz 36.0 GHz
19.0 GHz 38.0 GHz
20.0 GHz 40.0 GHz
20.1 GHz 40.2 GHz
21.0 GHz 42.0 GHz
21.75 GHz 43.5 GHz
22.0 GHz 44.0 GHz
23.0 GHz 46.0 GHz
24.0 GHz 48.0 GHz
1145.1155.82
1.46
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power Accuracy
Output power -10 dBm
Test frequency
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.1 GHz
11.0 GHz
12.0 GHz
12.6 GHz
12.7 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
17.0 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
1145.1155.82
Performance Test Report R&S® ZVA24
Reference
Min. value
Actual value
Max. value
Page 1.7
-2
-2
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.47
Unit
Measurement
uncertainty
dB
0.2 dB
2
2
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
E-5
Performance Test Report R&S® ZVA24
Parameter
Reference
24.0 GHz
Min. value
- 0.8
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Freq.
Level
Reference
Min. value
R&S ZVA
Actual value
________
Actual value
Max. value
Max. value
Page 1.8
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
500MHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
2 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.48
Measurement
uncertainty
Unit
Measurement
uncertainty
dB
0.1 dB
0.8
51 MHz
1145.1155.82
Unit
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Freq.
Level
Performance Test Report R&S® ZVA24
Reference
Min. value
Actual value
Max. value
Page 1.8
2.1 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
3 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
4 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
4.1 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.49
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA24
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Freq.
Level
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
6 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
8 GHz
23 dB
18 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
10 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
13 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.50
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Performance Test Report R&S® ZVA24
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
16 GHz
Level
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
20 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
24 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.51
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA24
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Freq.
Level
51 MHz 22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
500MHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
1145.1155.82
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1.52
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Freq.
1 GHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
2 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
1145.1155.82
Performance Test Report R&S® ZVA24
Reference
Min. value
Actual value
Max. value
Page 1.8
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1.53
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA24
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Freq.
Level
2.1 GHz 22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
3 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
1145.1155.82
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1.54
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Freq.
Level
4 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
4.1 GHz
22 dB
19 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
1145.1155.82
Performance Test Report R&S® ZVA24
Reference
Min. value
Actual value
Max. value
Page 1.8
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
1.55
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA24
Parameter
Reference
-3
-90 dB
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Freq.
6 GHz
Level
22 dB
19 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
8 GHz
22 dB
17 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
1145.1155.82
Min. value
R&S ZVA
Actual value
________
Max. value
Measurement
uncertainty
dB
0.1 dB
3
Page 1.8
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
1.56
Unit
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Performance Test Report R&S® ZVA24
Reference
-3
-3
-80 dB
-85 dB
-90 dB
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Min. value
Actual value
________
________
Max. value
Page 1.8
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
13 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
1.57
Measurement
uncertainty
dB
0.1 dB
3
3
Freq.
10 GHz
1145.1155.82
Unit
E-5
Performance Test Report R&S® ZVA24
Parameter
Reference
-3
-3
-3
-3
-75 dB
-80 dB
-85 dB
-90 dB
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Min. value
R&S ZVA
Actual value
________
________
________
________
Max. value
Page 1.8
Level
18 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
20 GHz
18 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
1.58
Measurement
uncertainty
dB
0.1 dB
3
3
3
3
Freq.
16 GHz
1145.1155.82
Unit
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Performance Test Report R&S® ZVA24
Reference
Min. value
-3
-3
-3
-80 dB
-85 dB
-90 dB
Actual value
________
________
________
Max. value
Unit
Measurement
uncertainty
dB
0.1 dB
3
3
3
Page 1.8
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Freq.
24 GHz
Level
18 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
1145.1155.82
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.59
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
E-5
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __
Power measurement
uncertainty
Page 1.9
Test frequency:
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1 GHz
1.5 GHz
2 GHz
2.1 GHz
2.5 GHz
3 GHz
3.5 GHz
4 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
17.0 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
1145.1155.82
Min. value
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
R&S ZVA
Actual value
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.60
Max. value
Unit
Measurement
uncertainty
dB
0.3 dB
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __
Input linearity
Reference –10 dBm
Page 1.10
Freq.
50 MHz
Min. value
Actual value
Max. value
Level
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
________
________
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
700 MHz 20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
________
________
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
2 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
________
________
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
8 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
________
________
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
1145.1155.82
1.61
Unit
Measurement
uncertainty
dB
0.01 dB
E-5
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __
Input linearity
Reference –10 dBm
Page 1.10
Min. value
R&S ZVA
Actual value
Max. value
Freq.
20 GHz
Level
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
________
________
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
24 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
________
________
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
1145.1155.82
1.62
Unit
Measurement
uncertainty
dB
0.01 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(without opt. gen/rec atten.
and dir. gen/rec access)
Test frequency
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.63
–80
–80
–80
–110
–110
–110
–110
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–110
–110
–110
–110
–110
–110
–110
–110
–110
–110
–110
–110
–110
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(with opt. rec attenuator)
Test frequency:
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.64
–79
–79
–79
–109
–109
–109
–109
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–108
–108
–108
–108
–108
–108
–108
–108
–108
–108
–108
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __
Input noise level
(with opt. direct gen/rec
Page 111
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
access)
Test frequency:
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.65
–78
–78
–78
–108
–108
–108
–108
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–115
–115
–115
–113
–113
–106
–106
–106
–106
–106
–106
–106
–106
–106
–106
–106
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __
Input noise level
(with opt. rec. attenuator and
Page 111
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
opt. direct gen/rec access)
Test frequency:
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.66
–77
–77
–77
–107
–107
–107
–107
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–104
–104
–104
–104
–104
–104
–104
–104
–104
–104
–104
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __
Matching (raw)
Page 1.12
Test frequency:
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.5 GHz
5.0 GHz
5.5 GHz
6.0 GHz
6.5 GHz
7.0 GHz
7.5 GHz
8.0 GHz
9.0 GHz
10.0 GHz
11.0 GHz
12.0 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
17.0 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
1145.1155.82
Min. value
10
10
12
12
12
12
12
12
12
12
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
Actual value
Max. value
Unit
Measurement
uncertainty
dB
1 dB
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.67
E-5
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(without options step atten.
and direct gen./rec. access)
Test frequency:
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GHz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
90
90
90
105
105
105
125
125
125
125
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
125
125
125
125
125
125
125
125
125
125
125
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.68
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with opt. gen. or rec. atten.)
Test frequency:
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GHz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
89
89
89
104
104
104
104
124
124
124
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
123
123
123
123
123
123
123
123
123
123
123
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.69
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
E-5
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with opt. gen. and rec. atten.
or with opt. direct gen./rec.
access)
Test frequency:
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GHz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
88
88
88
103
103
103
103
123
123
123
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
121
121
121
121
121
121
121
121
121
121
121
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.70
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with opt. gen. or rec. atten.
and with opt. direct gen./rec.
access)
Test frequency:
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GHz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
87
87
87
102
102
102
102
122
122
122
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
119
119
119
119
119
119
119
119
119
119
119
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.71
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
E-5
Performance Test Report R&S® ZVA24
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with opt. gen. and rec. atten.
and with opt. direct gen./rec.
access)
Test frequency:
10.12 MHz
20.12 MHz
50.12 MHz
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GHz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
86
86
86
101
101
101
101
121
121
121
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
117
117
117
117
117
117
117
117
117
117
117
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.72
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Receiver Step Atten.
Attenuation Accuracy
Reference 0 dB
Performance Test Report R&S® ZVA24
Reference
Min. value
Actual value
Max. value
Page 1.14
Atten.
5 dB
Frequ.
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0 GHz
20.0 GHz
22.0 GHz
24.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
10 dB
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0 GHz
20.0 GHz
22.0 GHz
24.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
20 dB
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0 GHz
20.0 GHz
22.0 GHz
24.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1145.1155.82
1.73
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA24
Parameter
Port __
Receiver Step Atten.
Attenuation Accuracy
Reference 0 dB
Atten.
Frequ.
35 dB
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0 GHz
20.0 GHz
22.0 GHz
24.0 GHz
1145.1155.82
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.14
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.74
Unit
Measurement
uncertainty
dB
0.1 dB
2
2
2
2
2
2
2
2
2
2
2
2
2
2
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA24
Parameter
Reference
Accuracy
DC meas 1 V
Page 1.15
Min. value
Actual value
Max. value
Pos. Input
-1000 m V
-300 mV
-10 mV
10 mV
300 mV
1000 m V
- 27.5
- 10.0
- 2.75
- 2.75
- 10.0
- 27.5
________
________
________
________
________
________
+ 27.5
+ 10.0
+ 2.75
+ 2.75
+ 10.0
+ 27.5
Neg. Input
-1000 m V
-300 mV
-10 mV
10 mV
300 mV
1000 m V
- 27.5
- 10.0
- 2.75
- 2.75
- 10.0
- 27.5
________
________
________
________
________
________
+ 27.5
+ 10.0
+ 2.75
+ 2.75
+ 10.0
+ 27.5
Accuracy
DC meas 10 V
Page 1.15
Pos. Input
-10.0 V
-3.0 V
-0.1 V
0.1 V
3.0 V
10.0 V
- 0.275
- 0.10
- 0.0275
- 0.0275
- 0.10
- 0.275
________
________
________
________
________
________
+ 0.275
+ 0.10
+ 0.0275
+ 0.0275
+ 0.10
+ 0.275
Neg. Input
-10.0 V
-3.0 V
-0.1 V
0.1 V
3.0 V
10.0 V
- 0.275
- 0.10
- 0.0275
- 0.0275
- 0.10
- 0.275
________
________
________
________
________
________
+ 0.275
+ 0.10
+ 0.0275
+ 0.0275
+ 0.10
+ 0.275
1145.1155.82
1.75
Unit
Measurement
uncertainty
mV
1 mV
V
0.01 V
E-5
Performance Test Report R&S® ZVA40
R&S ZVA
Performance Test Report R&S® ZVA40
ROHDE&SCHWARZ
Vector Network Analyzer, 40 GHz, _ ports
R&S® ZVA40
1145.1110K__
Serial number:
Date:
Person responsible:
Signature:
Parameter
Frequency deviation
@ 1 GHz
With Option ZVAB-B4
1145.1155.82
Reference
Min. value
Actual value
Max. value
Page 1.5
- 8000
_________
- 100
Unit
Measurement
uncertainty
Hz
1 Hz
+ 8000
+ 100
1.76
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Harmonics
Source power +10dBm
Freq.
Harmonics
50 MHz 100 MHz
150 MHz
Performance Test Report R&S® ZVA40
Reference
Min. value
Actual value
Max. value
Page 1.5
________
________
-20
-20
100 MHz 200 MHz
300 MHz
________
________
-20
-20
200 MHz 400 MHz
600 MHz
________
________
-20
-20
500 MHz 1000 MHz
1500 MHz
________
________
-20
-20
750 MHz 1500 MHz
2250 MHz
________
________
-20
-20
1 GHz
________
________
-20
-20
1.5 GHz 3 GHz
4.5 GHz
________
________
-20
-20
2 GHz
________
________
-20
-20
2.1 GHz 4.2 GHz
6.3 GHz
________
________
-20
-20
2.5 GHz 5.0 GHz
7.5 GHz
________
________
-20
-20
3.0 GHz 6.0 GHz
9.0 GHz
________
________
-20
-20
3.5 GHz 7 GHz
10.5 GHz
________
________
-20
-20
4.0 GHz 8.0 GHz
12.0 GHz
________
________
-20
-20
4.1 GHz 8.2 GHz
12.3 GHz
________
________
-20
-20
5.0 GHz 10.0 GHz
15.0 GHz
________
________
-20
-20
5.04 GHz 10.08 GHz
15.12 GHz
________
________
-20
-20
2 GHz
3 GHz
4 GHz
6 GHz
1145.1155.82
1.77
Unit
Measurement
uncertainty
dBc
1 dB
E-5
Performance Test Report R&S® ZVA40
Parameter
Port __
Harmonics
Freq.
Harmonics
5.05 GHz 10.10 GHz
15.15 GHz
Reference
Min. value
R&S ZVA
Actual value
Max. value
dBc
Page 1.5
________
________
-20
-20
5.5 GHz 11.0 GHz
16.5 GHz
________
________
-20
-20
6.0 GHz 12.0 GHz
18.0 GHz
________
________
-20
-20
6.35 GHz 12.70 GHz
19.05 GHz
________
________
-20
-20
7.0 GHz 14.0 GHz
21.0 GHz
________
________
-20
-20
8.0 GHz 16.0 GHz
24.0 GHz
________
________
-20
-20
8.1 GHz 16.2 GHz
24.3 GHz
________
________
-20
-20
9.0 GHz 18.0 GHz
27.0 GHz
________
________
-20
-20
10.0 GHz 20.0 GHz
30.0 GHz
________
________
-20
-20
10.2 GHz 20.4 GHz
30.6 GHz
________
________
-20
-20
11.0 GHz 22.0 GHz
33.0 GHz
________
________
-20
-20
12.7 GHz 25.4 GHz
38.1 GHz
________
________
-20
-20
13.0 GHz 26.0 GHz
39.0 GHz
________
________
-20
-20
14.0 GHz 28.0 GHz
42.0 GHz
________
________
-20
-20
14.6 GHz 29.2 GHz
43.8 GHz
________
________
-20
-20
15.0 GHz 30.0 GHz
45.0 GHz
________
________
-20
-20
16.0 GHz 32.0 GHz
________
-20
1145.1155.82
Unit
1.78
Measurement
uncertainty
2 dB
2 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Performance Test Report R&S® ZVA40
Reference
Min. value
Actual value
Max. value
Measurement
uncertainty
dBc
Page 1.5
Port __
Harmonics
Source power +10
dBm
Freq.
Harmonics
17.0 GHz 34.0 GHz
Unit
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
18.0 GHz 36.0 GHz
19.0 GHz 38.0 GHz
20.0 GHz 40.0 GHz
20.1 GHz 40.2 GHz
21.0 GHz 42.0 GHz
21.75 GHz 43.5 GHz
22.0 GHz 44.0 GHz
23.0 GHz 46.0 GHz
24.0 GHz 48.0 GHz
1145.1155.82
1.79
E-5
Performance Test Report R&S® ZVA40
Parameter
Port __
Power Accuracy
Output power -10 dBm
Test frequency:
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.1 GHz
11.0 GHz
12.0 GHz
12.6 GHz
12.7 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
17.0 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
1145.1155.82
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.7
-2
-2
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.80
Unit
Measurement
uncertainty
dB
0.2 dB
2
2
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Performance Test Report R&S® ZVA40
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
51 MHz
Level
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
500MHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
2 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.81
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA40
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
2.1 GHz
Level
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
3 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
4 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
4.1 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.82
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Performance Test Report R&S® ZVA40
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
6 GHz
Level
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
8 GHz
23 dB
18 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
10 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
13 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.83
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA40
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
16 GHz
Level
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
20 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
24 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
28 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
35 GHz
16 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.84
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Freq.
40 GHz
Level
16 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
1145.1155.82
Performance Test Report R&S® ZVA40
Reference
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
0.1 dB
Page 1.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
1.85
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Page 1.8
Min. value
R&S ZVA
Actual value
Max. value
Freq.
51 MHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
500MHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
1145.1155.82
1.86
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
-90 dB
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Performance Test Report R&S® ZVA40
Reference
Min. value
-3
Actual value
________
Max. value
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
2 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1.87
Measurement
uncertainty
dB
0.1 dB
3
Page 1.8
Freq.
1 GHz
1145.1155.82
Unit
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Page 1.8
Min. value
R&S ZVA
Actual value
Max. value
Freq.
2.1 GHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.88
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Page 1.8
Min. value
Actual value
Max. value
Freq.
4 GHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
4.1 GHz
22 dB
19 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.89
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Page 1.8
Min. value
R&S ZVA
Actual value
Max. value
Freq.
6 GHz
Level
22 dB
19 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
8 GHz
22 dB
17 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.90
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Page 1.8
Min. value
Actual value
Max. value
Freq.
10 GHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
13 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.91
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Page 1.8
Min. value
R&S ZVA
Actual value
Max. value
Freq.
16 GHz
Level
18 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
20 GHz
18 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.92
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Page 1.8
Min. value
Actual value
Max. value
Freq.
24 GHz
Level
18 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
28 GHz
17 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.93
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Freq.
32 GHz
Level
17 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
40 GHz
13 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-75 dB
-80 dB
-85 dB
-90 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.94
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Power measurement
uncertainty
Page 1.9
Test frequency:
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1 GHz
1.5 GHz
2 GHz
2.1 GHz
2.5 GHz
3 GHz
3.5 GHz
4 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
17.0 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
1145.1155.82
Min. value
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
Actual value
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.95
Max. value
Unit
Measurement
uncertainty
dB
0.3 dB
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Power measurement
uncertainty
Page 1.9
Test frequency:
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
1145.1155.82
Min. value
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
R&S ZVA
Actual value
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.96
Max. value
Unit
Measurement
uncertainty
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Input linearity
Reference –10 dBm
Performance Test Report R&S® ZVA40
Reference
Min. value
Actual value
Max. value
Page 1.10
50 MHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
________
________
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
1 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
4 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
8 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
16 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.3
0.1
0.1
0.1
0.1
0.1
0.1
1145.1155.82
1.97
Unit
Measurement
uncertainty
dB
0.01 dB
E-5
Performance Test Report R&S® ZVA40
Parameter
Port __
Input linearity
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.10
24 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
40 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
1145.1155.82
1.98
Unit
Measurement
uncertainty
dB
0.01 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(without opt. gen/rec atten.
and dir. gen/rec access
Test frequency:
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.99
–80
–80
-110
–110
–110
–110
–110
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–110
–110
–110
–110
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Input noise level
(without opt. gen/rec atten.
Page 1.11
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
and dir. gen/rec access
Test frequency
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.100
–100
–100
–100
–100
–100
–100
–100
–100
–95
–95
–95
–95
–95
–95
–95
–95
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Input noise level
(with opt. rec atten.)
Page 1.11
Test frequency:
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.101
–79
–79
–109
–109
–109
–109
–109
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–113
–113
–113
–113
–113
–113
–113
–108
–108
–108
–108
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Input noise level
(without opt. rec atten.)
Page 1.11
Test frequency
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
1145.1155.82
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.102
–97
–97
–97
–97
–97
–97
–97
–97
–92
–92
–92
–92
–92
–92
–92
–92
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(with opt. dir. gen/rec access)
Test frequency:
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.103
–78
–78
–108
–108
–108
–108
–108
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–111
–111
–111
–111
–111
–111
–111
–106
–106
–106
–106
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Input noise level
(with opt. dir. gen/rec access)
Page 1.11
Test frequency:
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
1145.1155.82
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.104
–94
–94
–94
–94
–94
–94
–94
–94
–89
–89
–89
–89
–89
–89
–89
–89
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(with opt. rec. atten. and opt.
dir. gen/rec access)
Test frequency:
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GHz
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
Port __
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–77
–77
–107
–107
–107
–107
–107
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–109
–109
–109
–109
–109
–109
–109
–104
–104
–104
–104
dBm
Page 1.11
1.105
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
Input noise level
(with opt. rec. atten. and opt.
dir. gen/rec access)
Test frequency:
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.106
–88
–88
–88
–88
–88
–88
–88
–88
–83
–83
–83
–83
–83
–83
–83
–83
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Matching (raw)
Page 1.12
Test frequency:
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.5 GHz
5.0 GHz
5.5 GHz
6.0 GHz
6.5 GHz
7.0 GHz
7.5 GHz
8.0 GHz
9.0 GHz
10.0 GHz
11.0 GHz
12.0 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
17.0 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
1145.1155.82
Min. value
12
12
12
12
12
12
12
12
12
12
12
12
12
12
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
6
6
6
6
6
6
6
6
6
6
6
6
Actual value
Max. value
Unit
Measurement
uncertainty
dB
1 dB
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.107
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __
Matching (raw)
Page 1.12
Test frequency:
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
1145.1155.82
Min. value
6
6
6
6
6
6
6
6
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
1 dB
________
________
________
________
________
________
________
________
1.108
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(without opt. step attenuator
and without opt. direct
generator/receiver access)
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
1145.1155.82
90
90
105
105
105
125
125
125
125
125
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.109
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(without opt. step attenuator
and without opt. direct
generator/receiver access)
Test frequency:
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
1145.1155.82
130
125
125
125
125
115
115
115
115
115
115
115
115
110
110
110
110
110
110
110
110
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.110
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with opt. generator or
receiver attenuator)
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
1145.1155.82
89
89
104
104
104
124
124
124
124
124
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
128
128
128
128
128
128
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.111
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
Page 1.13
Port __ to Port ___
Dynamic range
(with opt. generator or
receiver attenuator)
Test frequency:
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
1145.1155.82
128
123
123
123
123
112
112
112
112
112
112
112
112
107
107
107
107
107
107
107
107
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.112
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with opt. generator and
receiver attenuator or with
opt. direct generator/receiver
access)
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
1145.1155.82
88
88
103
103
103
123
123
123
123
123
123
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
126
126
126
126
126
126
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.113
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with opt. generator and
receiver attenuator or with
opt. direct generator/receiver
access)
Test frequency:
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
1145.1155.82
126
121
121
121
121
109
109
109
109
109
109
109
109
104
104
104
104
104
104
104
104
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.114
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with opt. generator or
receiver attenuator and with
opt. direct generator/receiver
access)
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
1145.1155.82
87
87
102
102
102
122
122
122
122
122
122
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
124
124
124
124
124
124
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.115
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
Page 1.13
Port __ to Port ___
Dynamic range
(with opt. generator or
receiver attenuator and with
opt. direct generator/receiver
access)
Test frequency:
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
1145.1155.82
124
119
119
119
119
106
106
106
106
106
106
106
106
101
101
101
101
101
101
101
101
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.116
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with opt. generator and
receiver attenuator and with
opt. direct generator/receiver
access)
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
1145.1155.82
86
86
101
101
101
121
121
121
121
121
121
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
122
122
122
122
122
122
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.117
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA40
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with opt. generator and
receiver attenuator and with
opt. direct generator/receiver
access)
Test frequency:
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
1145.1155.82
122
117
117
117
117
103
103
103
103
103
103
103
103
98
98
98
98
98
98
98
98
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.118
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Receiver Step Atten.
Attenuation Accuracy
Reference 0 dB
Performance Test Report R&S® ZVA40
Reference
Min. value
Actual value
Max. value
Page 1.14
Atten.
5 dB
Frequ.
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0 GHz
20.0 GHz
22.0 GHz
24.0 GHz
26.0 GHz
28.0 GHz
30.0 GHz
32.0 GHz
34.0 GHz
36.0 GHz
38.0 GHz
40.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
10 dB
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0 GHz
20.0 GHz
22.0 GHz
24.0 GHz
26.0 GHz
28.0 GHz
30.0 GHz
32.0 GHz
34.0 GHz
36.0 GHz
38.0 GHz
40.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1145.1155.82
1.119
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA40
Parameter
Port __
Receiver Step Atten.
Attenuation Accuracy
Reference 0 dB
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.14
Atten.
20 dB
Frequ.
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0 GHz
20.0 GHz
22.0 GHz
24.0 GHz
26.0 GHz
28.0 GHz
30.0 GHz
32.0 GHz
34.0 GHz
36.0 GHz
38.0 GHz
40.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
35 dB
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0GHz
20.0 GHz
22.0 GHz
24.0 GHz
26.0 GHz
28.0 GHz
30.0 GHz
32.0 GHz
34.0 GHz
36.0 GHz
38.0 GHz
40.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1145.1155.82
1.120
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA40
Parameter
Reference
Accuracy
DC meas 1 V
Page 1.15
Min. value
Actual value
Max. value
Pos. Input
-1000 m V
-300 mV
-10 mV
10 mV
300 mV
1000 m V
- 27.5
- 10.0
- 2.75
- 2.75
- 10.0
- 27.5
________
________
________
________
________
________
+ 27.5
+ 10.0
+ 2.75
+ 2.75
+ 10.0
+ 27.5
Neg. Input
-1000 m V
-300 mV
-10 mV
10 mV
300 mV
1000 m V
- 27.5
- 10.0
- 2.75
- 2.75
- 10.0
- 27.5
________
________
________
________
________
________
+ 27.5
+ 10.0
+ 2.75
+ 2.75
+ 10.0
+ 27.5
Accuracy
DC meas 10 V
Page 1.15
Pos. Input
-10.0 V
-3.0 V
-0.1 V
0.1 V
3.0 V
10.0 V
- 0.275
- 0.10
- 0.0275
- 0.0275
- 0.10
- 0.275
________
________
________
________
________
________
+ 0.275
+ 0.10
+ 0.0275
+ 0.0275
+ 0.10
+ 0.275
Neg. Input
-10.0 V
-3.0 V
-0.1 V
0.1 V
3.0 V
10.0 V
- 0.275
- 0.10
- 0.0275
- 0.0275
- 0.10
- 0.275
________
________
________
________
________
________
+ 0.275
+ 0.10
+ 0.0275
+ 0.0275
+ 0.10
+ 0.275
1145.1155.82
1.121
Unit
Measurement
uncertainty
mV
1 mV
V
0.01 V
E-5
Performance Test Report R&S® ZVA50
R&S ZVA
Performance Test Report R&S® ZVA50
ROHDE&SCHWARZ
Vector Network Analyzer, 50 GHz, _ ports
R&S® ZVA50
1145.1110K__
Serial number:
Date:
Person responsible:
Signature:
Parameter
Frequency deviation
@ 1 GHz
With Option ZVAB-B4
1145.1155.82
Reference
Min. value
Actual value
Max. value
Page 1.5
- 8000
_________
- 100
Unit
Measurement
uncertainty
Hz
1 Hz
+ 8000
+ 100
1.122
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Harmonics
Source power +10dBm
Freq.
50 MHz
Harmonics
100 MHz
150 MHz
Performance Test Report R&S® ZVA50
Reference
Min. value
Actual value
Max. value
Page 1.5
________
________
-20
-20
100 MHz 200 MHz
300 MHz
________
________
-20
-20
200 MHz 400 MHz
600 MHz
________
________
-20
-20
500 MHz 1000 MHz
1500 MHz
________
________
-20
-20
750 MHz 1500 MHz
2250 MHz
________
________
-20
-20
1 GHz
________
________
-20
-20
1.5 GHz 3 GHz
4.5 GHz
________
________
-20
-20
2 GHz
________
________
-20
-20
2.1 GHz 4.2 GHz
6.3 GHz
________
________
-20
-20
2.5 GHz 5.0 GHz
7.5 GHz
________
________
-20
-20
3.0 GHz 6.0 GHz
9.0 GHz
________
________
-20
-20
3.5 GHz 7 GHz
10.5 GHz
________
________
-20
-20
4.0 GHz 8.0 GHz
12.0 GHz
________
________
-20
-20
4.1 GHz 8.2 GHz
12.3 GHz
________
________
-20
-20
5.0 GHz 10.0 GHz
15.0 GHz
________
________
-20
-20
2 GHz
3 GHz
4 GHz
6 GHz
1145.1155.82
1.123
Unit
Measurement
uncertainty
dBc
1 dB
E-5
Performance Test Report R&S® ZVA50
Parameter
Port __
Harmonics
Freq.
Harmonics
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.5
5.04 GHz 10.08 GHz
15.12 GHz
________
________
-20
-20
5.05 GHz 10.10 GHz
15.15 GHz
________
________
-20
-20
5.5 GHz 11.0 GHz
16.5 GHz
________
________
-20
-20
6.0 GHz 12.0 GHz
18.0 GHz
________
________
-20
-20
6.35 GHz 12.70 GHz
19.05 GHz
________
________
-20
-20
7.0 GHz 14.0 GHz
21.0 GHz
________
________
-20
-20
8.0 GHz 16.0 GHz
24.0 GHz
________
________
-20
-20
8.1 GHz 16.2 GHz
24.3 GHz
________
________
-20
-20
9.0 GHz 18.0 GHz
27.0 GHz
________
________
-20
-20
10.0 GHz 20.0 GHz
30.0 GHz
________
________
-20
-20
10.2 GHz 20.4 GHz
30.6 GHz
________
________
-20
-20
11.0 GHz 22.0 GHz
33.0 GHz
________
________
-20
-20
12.7 GHz 25.4 GHz
38.1 GHz
________
________
-20
-20
13.0 GHz 26.0 GHz
39.0 GHz
________
________
-20
-20
14.0 GHz 28.0 GHz
42.0 GHz
________
________
-20
-20
14.6 GHz 29.2 GHz
43.8 GHz
________
________
-20
-20
1145.1155.82
1.124
Unit
Measurement
uncertainty
dBc
2 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Harmonics
Source power +10
dBm
Freq.
Harmonics
15.0 GHz 30.0 GHz
45.0 GHz
Performance Test Report R&S® ZVA50
Reference
Min. value
Actual value
Max. value
Page 1.5
________
________
-20
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
Unit
Measurement
uncertainty
dBc
2 dB
16.0 GHz 32.0 GHz
17.0 GHz 34.0 GHz
18.0 GHz 36.0 GHz
19.0 GHz 38.0 GHz
20.0 GHz 40.0 GHz
Source power +5dBm
20.1 GHz 40.2 GHz
21.0 GHz 42.0 GHz
21.75 GHz 43.5 GHz
22.0 GHz 44.0 GHz
23.0 GHz 46.0 GHz
24.0 GHz 48.0 GHz
25.0 GHz 50.0 GHz
1145.1155.82
1.125
E-5
Performance Test Report R&S® ZVA50
Parameter
Port __
Power Accuracy
Output power -10 dBm
Test frequency
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.1 GHz
11.0 GHz
12.0 GHz
12.6 GHz
12.7 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
17.0 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
1145.1155.82
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.7
-3
-3
-3
-3
-3
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.126
Unit
Measurement
uncertainty
dB
0.2 dB
3
3
3
3
3
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power Accuracy
Output power -10 dBm
Test frequency
25 GHz
26 GHz
27 GHz
28 GHz
29 GHz
30 GHz
31 GHz
32 GHz
33 GHz
34 GHz
35 GHz
36 GHz
37 GHz
38 GHz
39 GHz
40 GHz
41 GHz
42 GHz
43 GHz
44 GHz
45 GHz
46 GHz
47 GHz
48 GHz
49 GHz
50 GHz
1145.1155.82
Performance Test Report R&S® ZVA50
Reference
Min. value
Actual value
Max. value
Page 1.7
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.127
Unit
Measurement
uncertainty
dB
0.2 dB
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
E-5
Performance Test Report R&S® ZVA50
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Freq.
51 MHz
Level
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
500MHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
1 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
2 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
1145.1155.82
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.128
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Performance Test Report R&S® ZVA50
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
2.1 GHz
Level
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
3 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
4 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
4.1 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.129
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA50
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
6 GHz
Level
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
8 GHz
23 dB
18 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
10 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
13 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.130
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Performance Test Report R&S® ZVA50
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
16 GHz
Level
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
20 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
24 GHz
30 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
28 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
35 GHz
16 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.131
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Min. value
- 0.8
- 0.8
-15 dB
-20 dB
R&S ZVA
Actual value
________
________
Max. value
Unit
Measurement
uncertainty
dB
0.1 dB
0.8
0.8
Page 1.8
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Freq.
40 GHz
Level
16 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
45 GHz
16 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
50 GHz
16 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.132
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Performance Test Report R&S® ZVA50
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
51 MHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
500MHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.133
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA50
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
1 GHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
2 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.134
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Performance Test Report R&S® ZVA50
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
2.1 GHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.135
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA50
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
4 GHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
4.1 GHz
22 dB
19 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.136
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Performance Test Report R&S® ZVA50
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
6 GHz
Level
22 dB
19 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
8 GHz
22 dB
17 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.137
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA50
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
10 GHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
13 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.138
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Performance Test Report R&S® ZVA50
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
16 GHz
Level
21 dB
18 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
20 GHz
21 dB
18 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.139
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA50
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
24 GHz
Level
18 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
28 GHz
17 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.140
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Performance Test Report R&S® ZVA50
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
32 GHz
Level
17 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
40 GHz
13 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.141
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA50
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
45 GHz
Level
13 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
50 GHz
13 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.142
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Power measurement
uncertainty
Page 1.9
Test frequency:
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1 GHz
1.5 GHz
2 GHz
2.1 GHz
2.5 GHz
3 GHz
3.5 GHz
4 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
17.0 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
1145.1155.82
Min. value
-2
-2
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
Actual value
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.143
Max. value
Unit
Measurement
uncertainty
dB
0.3 dB
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Power measurement
uncertainty
Page 1.9
Test frequency:
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
1145.1155.82
Min. value
R&S ZVA
Actual value
Max. value
Unit
dB
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.144
Measurement
uncertainty
0.3 dB
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Input linearity
Reference –10 dBm
Page 1.10
Min. value
Actual value
Max. value
Freq.
50 MHz
Level
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
________
________
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
1 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
4 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
8 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
16 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.3
0.1
0.1
0.1
0.1
0.1
0.1
1145.1155.82
1.145
Unit
Measurement
uncertainty
dB
0.01 dB
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Input linearity
Reference –10 dBm
Page 1.10
Min. value
R&S ZVA
Actual value
Max. value
Freq.
24 GHz
Level
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
40 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
50 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0. 1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
1145.1155.82
1.146
Unit
Measurement
uncertainty
dB
0.01 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(without opt. gen/rec atten.
and dir. gen/rec access
Test frequency
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GH
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.147
–80
–80
–110
–110
–110
–110
–110
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–110
–110
–110
–110
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Input noise level
(without opt. gen/rec atten.
Page 1.11
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
and dir. gen/rec access
Test frequency
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.148
–105
–105
–105
–105
–105
–105
–105
–105
–100
–100
–100
–100
–100
–100
–100
–100
–95
–95
–95
–95
–95
–95
–95
–95
–95
–95
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(with opt. receiver atten.)
Test frequency
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GH
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.149
–79
–79
–109
–109
–109
–109
–109
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–113
–113
–113
–113
–113
–113
–113
–108
–108
–108
–108
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Input noise level
(with opt. receiver atten.)
Page 1.11
Test frequency
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
1145.1155.82
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.150
–102
–102
–102
–102
–102
–102
–102
–102
–97
–97
–97
–97
–97
–97
–97
–97
–92
–92
–92
–92
–92
–92
–92
–92
–92
–92
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(with opt. dir. gen/rec access)
Test frequency
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GH
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.151
–78
–78
–108
–108
–108
–108
–108
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–111
–111
–111
–111
–111
–111
–111
–106
–106
–106
–106
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Input noise level
(with opt. dir. gen/rec access)
Page 1.11
Test frequency
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
1145.1155.82
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.152
–103
–103
–103
–103
–103
–103
–103
–103
–98
–98
–98
–98
–98
–98
–98
–98
–93
–93
–93
–93
–93
–93
–93
–93
–93
–93
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(with opt. rec atten. and
dir. gen/rec access)
Test frequency
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GH
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.153
–77
–77
–107
–107
–107
–107
–107
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–110
–110
–110
–110
–110
–110
–110
–105
–105
–105
–105
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(with opt. rec atten. and
dir. gen/rec access)
Test frequency
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.154
–96
–96
–96
–96
–96
–96
–96
–96
–91
–91
–91
–91
–91
–91
–91
–91
–86
–86
–86
–86
–86
–86
–86
–86
–86
–86
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Matching (raw)
Page 1.12
Test frequency
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.5 GHz
5.0 GHz
5.5 GHz
6.0 GHz
6.5 GHz
7.0 GHz
7.5 GHz
8.0 GHz
9.0 GHz
10.0 GHz
11.0 GHz
12.0 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
17.0 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
1145.1155.82
Min. value
8
8
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
8
8
8
8
8
8
8
8
8
8
6
6
6
6
6
6
6
6
6
6
6
6
Actual value
Max. value
Unit
Measurement
uncertainty
dB
1 dB
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.155
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __
Matching (raw)
Page 1.12
Test frequency
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
1145.1155.82
Min. value
6
6
6
6
6
6
6
6
5
5
5
5
5
5
5
5
5
5
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
1 dB
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.156
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __ to Port ___
Dynamic range
(without option step
attenuator and without
option direct
generator/receiver
access)
Page 1.13
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
20.0 GHz
1145.1155.82
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
90
90
105
105
105
125
125
125
125
125
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
130
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.157
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Min. value
Actual value
R&S ZVA
Max. value
Unit
Measurement
uncertainty
dB
Page 1.13
Port __ to Port ___
Dynamic range
(without option step
attenuator and without
option direct
generator/receiver
access)
Test frequency:
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
1145.1155.82
125
125
125
125
120
120
120
120
120
120
120
120
115
115
115
115
115
115
115
115
110
110
110
110
110
110
110
110
110
110
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.158
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __ to Port ___
Dynamic range
(with option generator or
receiver attenuator)
Page 1.13
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
1145.1155.82
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
89
89
104
104
104
124
124
124
124
124
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
128
128
128
128
128
128
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.159
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __ to Port ___
Dynamic range
(with option generator or
receiver attenuator)
Page 1.13
Test frequency:
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
1145.1155.82
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
128
123
123
123
123
117
117
117
117
117
117
117
117
112
112
112
112
112
112
112
112
107
107
107
107
107
107
107
107
107
107
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.160
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __ to Port ___
Dynamic range
(with option generator
and receiver attenuator or
with option direct
generator/receiver
access)
Page 1.13
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
1145.1155.82
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
88
88
103
103
103
123
123
123
123
123
123
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
128
126
126
126
126
126
126
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.161
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Min. value
R&S ZVA
Actual value
Test frequency:
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
1145.1155.82
Unit
Measurement
uncertainty
dB
Page 1.13
Port __ to Port ___
Dynamic range
ZVA440, ZVA50
(with option generator
and receiver attenuator or
with option direct
generator/receiver
access)
Max. value
126
121
121
121
121
114
114
114
114
114
114
114
114
109
109
109
109
109
109
109
109
104
104
104
104
104
104
104
104
104
104
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.162
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __ to Port ___
Dynamic range
(with option generator or
receiver attenuator and
with option direct
generator/receiver
access)
Page 1.13
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
1145.1155.82
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
87
87
102
102
102
122
122
122
122
122
122
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
124
124
124
124
124
124
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.163
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Min. value
R&S ZVA
Actual value
Test frequency:
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
1145.1155.82
Unit
Measurement
uncertainty
dB
Page 1.13
Port __ to Port ___
Dynamic range
ZVA440, ZVA50
(with option generator or
receiver attenuator and
with option direct
generator/receiver
access)
Max. value
124
119
119
119
119
111
111
111
111
111
111
111
111
106
106
106
106
106
106
106
106
101
101
101
101
101
101
101
101
101
101
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.164
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA50
Parameter
Reference
Port __ to Port ___
Dynamic range
(with option generator
and receiver attenuator
and with option direct
generator/receiver
access)
Page 1.13
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
1145.1155.82
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
86
86
101
101
101
121
121
121
121
121
121
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
122
122
122
122
122
122
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.165
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Min. value
R&S ZVA
Actual value
Test frequency:
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
1145.1155.82
Unit
Measurement
uncertainty
dB
Page 1.13
Port __ to Port ___
Dynamic range
(with option generator
and receiver attenuator
and with option direct
generator/receiver
access)
Max. value
122
117
117
117
117
108
108
108
108
108
108
108
108
103
103
103
103
103
103
103
103
98
98
98
98
98
98
98
98
98
98
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.166
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Receiver Step Atten.
Attenuation Accuracy
Reference 0 dB
Performance Test Report R&S® ZVA50
Reference
Min. value
Actual value
Max. value
Page 1.14
Atten.
5 dB
Frequ.
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0 GHz
20.0 GHz
22.0 GHz
24.0 GHz
26.0 GHz
28.0 GHz
30.0 GHz
32.0 GHz
34.0 GHz
36.0 GHz
38.0 GHz
40.0 GHz
42.0 GHz
44.0 GHz
46.0 GHz
48.0 GHz
50.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
10 dB
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0 GHz
20.0 GHz
22.0 GHz
24.0 GHz
26.0 GHz
28.0 GHz
30.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1145.1155.82
1.167
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
-2
32.0 GHz
Port __
Receiver Step Atten.
Attenuation Accuracy
Reference 0 dB
Min. value
R&S ZVA
Actual value
________
Max. value
Page 1.14
Frequ.
34.0 GHz
36.0 GHz
38.0 GHz
40.0 GHz
42.0 GHz
44.0 GHz
46.0 GHz
48.0 GHz
50.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
20 dB
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0 GHz
20.0 GHz
22.0 GHz
24.0 GHz
26.0 GHz
28.0 GHz
30.0 GHz
32.0 GHz
34.0 GHz
36.0 GHz
38.0 GHz
40.0 GHz
42.0 GHz
44.0 GHz
46.0 GHz
48.0 GHz
50.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
35 dB
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
2
2
2
2
2
2
2
1.168
Measurement
uncertainty
dB
0.1 dB
2
Atten.
10 dB
1145.1155.82
Unit
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Performance Test Report R&S® ZVA50
Reference
-2
-2
-2
12.0 GHz
14.0 GHz
16.0 GHz
Port __
Receiver Step Atten.
Attenuation Accuracy
Reference 0 dB
Atten.
35 dB
Frequ.
18.0GHz
20.0 GHz
22.0 GHz
24.0 GHz
26.0 GHz
28.0 GHz
30.0 GHz
32.0 GHz
34.0 GHz
36.0 GHz
38.0 GHz
40.0 GHz
42.0 GHz
44.0 GHz
46.0 GHz
48.0 GHz
50.0 GHz
1145.1155.82
Min. value
Actual value
________
________
________
Max. value
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.169
Measurement
uncertainty
dB
0.1 dB
2
2
2
Page 1.14
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
Unit
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
E-5
Performance Test Report R&S® ZVA50
Parameter
Reference
Accuracy
DC meas 1 V
Page 1.15
Min. value
R&S ZVA
Actual value
Max. value
Pos. Input
-1000 m V
-300 mV
-10 mV
10 mV
300 mV
1000 m V
- 27.5
- 10.0
- 2.75
- 2.75
- 10.0
- 27.5
________
________
________
________
________
________
+ 27.5
+ 10.0
+ 2.75
+ 2.75
+ 10.0
+ 27.5
Neg. Input
-1000 m V
-300 mV
-10 mV
10 mV
300 mV
1000 m V
- 27.5
- 10.0
- 2.75
- 2.75
- 10.0
- 27.5
________
________
________
________
________
________
+ 27.5
+ 10.0
+ 2.75
+ 2.75
+ 10.0
+ 27.5
Accuracy
DC meas 10 V
Page 1.15
Pos. Input
-10.0 V
-3.0 V
-0.1 V
0.1 V
3.0 V
10.0 V
- 0.275
- 0.10
- 0.0275
- 0.0275
- 0.10
- 0.275
________
________
________
________
________
________
+ 0.275
+ 0.10
+ 0.0275
+ 0.0275
+ 0.10
+ 0.275
Neg. Input
-10.0 V
-3.0 V
-0.1 V
0.1 V
3.0 V
10.0 V
- 0.275
- 0.10
- 0.0275
- 0.0275
- 0.10
- 0.275
________
________
________
________
________
________
+ 0.275
+ 0.10
+ 0.0275
+ 0.0275
+ 0.10
+ 0.275
1145.1155.82
1.170
Unit
Measurement
uncertainty
mV
1 mV
V
0.01 V
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA67
Performance Test Report R&S® ZVA67
ROHDE&SCHWARZ
Vector Network Analyzer, 67 GHz, _ ports
R&S® ZVA67
1145.1110K__
Serial number:
Date:
Person responsible:
Signature:
Parameter
Frequency deviation
@ 1 GHz
With Option ZVAB-B4
1145.1155.82
Reference
Min. value
Actual value
Max. value
Page 1.5
- 8000
_________
- 100
Unit
Measurement
uncertainty
Hz
1 Hz
+ 8000
+ 100
1.171
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Harmonics
Page 1.5
Min. value
R&S ZVA
Actual value
Max. value
Source power +7dBm
Freq.
Harmonics
50 MHz 100 MHz
150 MHz
________
________
-20
-20
Source power +10dBm
100 MHz 200 MHz
300 MHz
________
________
-20
-20
200 MHz 400 MHz
600 MHz
________
________
-20
-20
500 MHz 1000 MHz
1500 MHz
________
________
-20
-20
750 MHz 1500 MHz
2250 MHz
________
________
-20
-20
1 GHz
________
________
-20
-20
1.5 GHz 3 GHz
4.5 GHz
________
________
-20
-20
2 GHz
________
________
-20
-20
2.1 GHz 4.2 GHz
6.3 GHz
________
________
-20
-20
2.5 GHz 5.0 GHz
7.5 GHz
________
________
-20
-20
3.0 GHz 6.0 GHz
9.0 GHz
________
________
-20
-20
3.5 GHz 7 GHz
10.5 GHz
________
________
-20
-20
4.0 GHz 8.0 GHz
12.0 GHz
________
________
-20
-20
4.1 GHz 8.2 GHz
12.3 GHz
________
________
-20
-20
5.0 GHz 10.0 GHz
15.0 GHz
________
________
-20
-20
2 GHz
3 GHz
4 GHz
6 GHz
Port __
1145.1155.82
Page 1.5
1.172
Unit
Measurement
uncertainty
dBc
1 dB
dBc
2 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Performance Test Report R&S® ZVA67
Reference
Min. value
Actual value
Max. value
Harmonics
Source power +7dBm
Freq.
Harmonics
5.04 GHz 10.08 GHz
15.12 GHz
________
________
-20
-20
5.05 GHz 10.10 GHz
15.15 GHz
________
________
-20
-20
5.5 GHz 11.0 GHz
16.5 GHz
________
________
-20
-20
6.0 GHz 12.0 GHz
18.0 GHz
________
________
-20
-20
6.35 GHz 12.70 GHz
19.05 GHz
________
________
-20
-20
7.0 GHz 14.0 GHz
21.0 GHz
________
________
-20
-20
8.0 GHz 16.0 GHz
24.0 GHz
________
________
-20
-20
8.1 GHz 16.2 GHz
24.3 GHz
________
________
-20
-20
9.0 GHz 18.0 GHz
27.0 GHz
________
________
-20
-20
10.0 GHz 20.0 GHz
30.0 GHz
________
________
-20
-20
10.2 GHz 20.4 GHz
30.6 GHz
________
________
-20
-20
11.0 GHz 22.0 GHz
33.0 GHz
________
________
-20
-20
12.7 GHz 25.4 GHz
38.1 GHz
________
________
-20
-20
13.0 GHz 26.0 GHz
39.0 GHz
________
________
-20
-20
14.0 GHz 28.0 GHz
42.0 GHz
________
________
-20
-20
14.6 GHz 29.2 GHz
43.8 GHz
________
________
-20
-20
Port __
1145.1155.82
Page 1.5
1.173
Unit
Measurement
uncertainty
dBc
2 dB
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
Harmonics
Source power +10
dBm
Freq.
Harmonics
15.0 GHz 30.0 GHz
45.0 GHz
________
________
-20
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
________
-20
16.0 GHz 32.0 GHz
17.0 GHz 34.0 GHz
18.0 GHz 36.0 GHz
19.0 GHz 38.0 GHz
20.0 GHz 40.0 GHz
Source power +5dBm
20.1 GHz 40.2 GHz
21.0 GHz 42.0 GHz
21.75 GHz 43.5 GHz
22.0 GHz 44.0 GHz
23.0 GHz 46.0 GHz
24.0 GHz 48.0 GHz
25.0 GHz 50.0 GHz
26.0 GHz 52.0 GHz
27.0 GHz 54.0 GHz
28.0 GHz 56.0 GHz
29.0 GHz 58.0 GHz
30.0 GHz 60.0 GHz
31.0 GHz 62.0 GHz
32.0 GHz 64.0 GHz
1145.1155.82
1.174
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power Accuracy
Output power -10 dBm
Test frequency
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.1 GHz
11.0 GHz
12.0 GHz
12.6 GHz
12.7 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
17.0 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
1145.1155.82
Performance Test Report R&S® ZVA67
Reference
Min. value
Actual value
Max. value
Page 1.7
-3
-3
-3
-3
-3
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.175
Unit
Measurement
uncertainty
dB
0.2 dB
3
3
3
3
3
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
E-5
Performance Test Report R&S® ZVA67
Parameter
Port __
Power Accuracy
Output power -10 dBm
Test frequency
25 GHz
26 GHz
27 GHz
28 GHz
29 GHz
30 GHz
31 GHz
32 GHz
33 GHz
34 GHz
35 GHz
36 GHz
37 GHz
38 GHz
39 GHz
40 GHz
41 GHz
42 GHz
43 GHz
44 GHz
45 GHz
46 GHz
47 GHz
48 GHz
49 GHz
50 GHz
52 GHz
54 GHz
56 GHz
58 GHz
60 GHz
62 GHz
64 GHz
66 GHz
67 GHz
1145.1155.82
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.7
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.176
Unit
Measurement
uncertainty
dB
0.2 dB
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Performance Test Report R&S® ZVA67
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
51 MHz
Level
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
500MHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
2 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.177
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA67
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
2.1 GHz
Level
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
3 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
4 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
4.1 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.178
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Performance Test Report R&S® ZVA67
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
6 GHz
Level
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
8 GHz
23 dB
18 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
10 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
13 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.179
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA67
Parameter
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
16 GHz
Level
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
20 GHz
23 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
24 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
28 GHz
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
35 GHz
16 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.180
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Performance Test Report R&S® ZVA67
Reference
- 0.8
-20 dB
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Min. value
Actual value
________
Max. value
Page 1.8
Level
16 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
45 GHz
16 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
50 GHz
16 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
55 GHz
12 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
60 GHz
12 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.181
Measurement
uncertainty
dB
0.1 dB
0.8
Freq.
40 GHz
1145.1155.82
Unit
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Unit
Measurement
uncertainty
dB
0.1 dB
Port __
Power linearity
(without Opt. Gen Att)
Reference –10 dBm
Freq.
65 GHz
Level
12 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
67 GHz
12 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
- 0.8
________
________
________
________
________
________
________
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1145.1155.82
1.182
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Performance Test Report R&S® ZVA67
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
51 MHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
500MHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.183
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA67
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
1 GHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
2 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.184
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Performance Test Report R&S® ZVA67
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
2.1 GHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.185
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA67
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
4 GHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
4.1 GHz
22 dB
19 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.186
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Performance Test Report R&S® ZVA67
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
6 GHz
Level
22 dB
19 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
8 GHz
22 dB
17 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.187
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA67
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
10 GHz
Level
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
13 GHz
22 dB
20 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.188
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Performance Test Report R&S® ZVA67
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
16 GHz
Level
21 dB
18 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
20 GHz
21 dB
18 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.189
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA67
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
24 GHz
Level
18 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
28 GHz
17 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.190
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Performance Test Report R&S® ZVA67
Reference
Min. value
Actual value
Max. value
Page 1.8
Freq.
32 GHz
Level
17 dB
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
40 GHz
13 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.191
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA67
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Max. value
Page 1.8
Freq.
45 GHz
Level
13 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
50 GHz
13 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
1145.1155.82
1.192
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Performance Test Report R&S® ZVA67
Reference
Min. value
Actual value
Page 1.8
Freq.
55 GHz
Level
9 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
60 GHz
9 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1145.1155.82
1.193
Max. value
Unit
Measurement
uncertainty
dB
0.1 dB
E-5
Performance Test Report R&S® ZVA67
Parameter
Port __
Power linearity
(with Opt. Gen Atten)
Reference –10 dBm
Reference
Min. value
R&S ZVA
Actual value
Unit
Measurement
uncertainty
dB
0.1 dB
Page 1.8
65 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
67 GHz
9 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
-45 dB
-50 dB
-55 dB
-60 dB
-65 dB
-70 dB
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-3
-3
-3
-3
-3
-3
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1145.1155.82
Max. value
1.194
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Power measurement
uncertainty
Page 1.9
Test frequency:
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1 GHz
1.5 GHz
2 GHz
2.1 GHz
2.5 GHz
3 GHz
3.5 GHz
4 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
17.0 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
1145.1155.82
Min. value
-2
-2
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
Actual value
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.195
Max. value
Unit
Measurement
uncertainty
dB
0.3 dB
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Power measurement
uncertainty
Page 1.9
Test frequency:
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
51.0 GHz
52.0 GHz
53.0 GHz
54.0 GHz
55.0 GHz
56.0 GHz
57.0 GHz
58.0 GHz
59.0 GHz
60.0 GHz
61.0 GHz
62.0 GHz
63.0 GHz
64.0 GHz
65.0 GHz
66.0 GHz
67.0 GHz
1145.1155.82
Min. value
R&S ZVA
Actual value
Max. value
Unit
dB
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
-4
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.196
Measurement
uncertainty
0.3 dB
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Input linearity
Reference –10 dBm
Page 1.10
Min. value
Actual value
Max. value
Freq.
50 MHz
Level
15 dB
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
________
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
1 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
4 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
8 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
16 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.3
0.1
0.1
0.1
0.1
0.1
0.1
1145.1155.82
1.197
Unit
Measurement
uncertainty
dB
0.01 dB
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Input linearity
Reference –10 dBm
Page 1.10
Min. value
R&S ZVA
Actual value
Max. value
Freq.
24 GHz
Level
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
40 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
50 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
60 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
67 GHz
10 dB
5 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
________
________
________
________
________
________
________
________
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
1145.1155.82
1.198
Unit
Measurement
uncertainty
dB
0.01 dB
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(without opt. gen/rec atten.
and dir. gen/rec access
Test frequency
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GH
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.199
–90
–90
–105
–105
–105
–105
–105
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–115
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Input noise level
(without opt. gen/rec atten.
Page 1.11
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
and dir. gen/rec access
Test frequency
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
51.0 GHz
52.0 GHz
53.0 GHz
54.0 GHz
55.0 GHz
56.0 GHz
57.0 GHz
58.0 GHz
59.0 GHz
60.0 GHz
61.0 GHz
62.0 GHz
63.0 GHz
64.0 GHz
65.0 GHz
66.0 GHz
67.0 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.200
–105
–105
–105
–105
–105
–105
–105
–105
–105
–105
–105
–105
–105
–105
–105
–105
–100
–100
–100
–100
–100
–100
–100
–100
–100
–100
–95
–95
–95
–95
–95
–95
–95
–95
–95
–95
–95
–95
–95
–95
–95
–95
–95
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Input noise level
(with opt. rec atten.)
Page 1.11
Test frequency
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GH
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.201
–89
–89
–104
–104
–104
–104
–104
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–114
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Input noise level
(with opt. rec atten.)
Page 1.11
Test frequency
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
51.0 GHz
52.0 GHz
53.0 GHz
54.0 GHz
55.0 GHz
56.0 GHz
57.0 GHz
58.0 GHz
59.0 GHz
60.0 GHz
61.0 GHz
62.0 GHz
63.0 GHz
64.0 GHz
65.0 GHz
66.0 GHz
67.0 GHz
1145.1155.82
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.202
–102
–102
–102
–102
–102
–102
–102
–102
–102
–102
–102
–102
–102
–102
–102
–102
–97
–97
–97
–97
–97
–97
–97
–97
–97
–97
–92
–92
–92
–92
–92
–92
–92
–92
–92
–92
–92
–92
–92
–92
–92
–92
–92
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(with opt. dir. gen/rec access)
Test frequency
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GH
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.203
–88
–88
–103
–103
–103
–103
–103
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–113
–111
–111
–111
–111
–111
–111
–111
–111
–111
–111
–111
–111
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Input noise level
(with opt. dir. gen/rec access)
Page 1.11
Test frequency
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
51.0 GHz
52.0 GHz
53.0 GHz
54.0 GHz
55.0 GHz
56.0 GHz
57.0 GHz
58.0 GHz
59.0 GHz
60.0 GHz
61.0 GHz
62.0 GHz
63.0 GHz
64.0 GHz
65.0 GHz
66.0 GHz
67.0 GHz
1145.1155.82
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.204
–99
–99
–99
–99
–99
–99
–99
–99
–99
–99
–99
–99
–99
–99
–99
–99
–94
–94
–94
–94
–94
–94
–94
–94
–94
–94
–89
–89
–89
–89
–89
–89
–89
–89
–89
–89
–89
–89
–89
–89
–89
–89
–89
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(with opt. rec atten. and
dir. gen/rec access)
Test frequency
100.12 MHz
200.12 MHz
500.12 MHz
700.12 MHz
750.12 MHz
1.00012 GHz
1.50012 GH
2.00012 GHz
2.10012 GHz
2.50012 GHz
3.00012 GHz
3.50012 GHz
4.00012 GMz
4.10012 GHz
4.50012 GHz
5.00012 GHz
5.05012 GHz
5.70012 GHz
6.00012 GHz
6.35012 GHz
6.36012 GHz
7.00012 GHz
7.50012 GHz
7.99988 GHz
8.10012 GHz
9.00012 GHz
10.00012 GHz
10.20012 GHz
11.00012 GHz
12.00012 GHz
12.70012 GHz
12.80012 GHz
12.99988 GHz
14.00012 GHz
15.00012 GHz
16.00012 GHz
16.10012 GHz
18.00012 GHz
19.00012 GHz
20.00012 GHz
21.00012 GHz
22.00012 GHz
23.00012 GHz
23.99988 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.205
–87
–87
–102
–102
–102
–102
–102
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–112
–109
–109
–109
–109
–109
–109
–109
–109
–109
–109
–109
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Input noise level
Page 1.11
Min. value
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dBm
(with opt. rec atten. and
dir. gen/rec access)
Test frequency
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
51.0 GHz
52.0 GHz
53.0 GHz
54.0 GHz
55.0 GHz
56.0 GHz
57.0 GHz
58.0 GHz
59.0 GHz
60.0 GHz
61.0 GHz
62.0 GHz
63.0 GHz
64.0 GHz
65.0 GHz
66.0 GHz
67.0 GHz
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.206
–96
–96
–96
–96
–96
–96
–96
–96
–96
–96
–96
–96
–96
–96
–96
–96
–91
–91
–91
–91
–91
–91
–91
–91
–91
–91
–86
–86
–86
–86
–86
–86
–86
–86
–86
–86
–86
–86
–86
–86
–86
–86
–86
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Matching (raw)
Page 1.12
Test frequency
10 MHz
20 MHz
50 MHz
100 MHz
200 MHz
500 MHz
750 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.5 GHz
5.0 GHz
5.5 GHz
6.0 GHz
6.5 GHz
7.0 GHz
7.5 GHz
8.0 GHz
9.0 GHz
10.0 GHz
11.0 GHz
12.0 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
17.0 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
1145.1155.82
Min. value
8
8
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
8
8
8
8
8
8
8
8
8
8
6
6
6
6
6
6
6
6
6
6
6
6
Actual value
Max. value
Unit
Measurement
uncertainty
dB
1 dB
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.207
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __
Matching (raw)
Page 1.12
Test frequency
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
51.0 GHz
52.0 GHz
53.0 GHz
54.0 GHz
55.0 GHz
56.0 GHz
57.0 GHz
58.0 GHz
59.0 GHz
60.0 GHz
61.0 GHz
62.0 GHz
63.0 GHz
64.0 GHz
65.0 GHz
66.0 GHz
67.0 GHz
1145.1155.82
Min. value
6
6
6
6
6
6
6
6
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
R&S ZVA
Actual value
Max. value
Unit
Measurement
uncertainty
dB
1 dB
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.208
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(without option step
attenuator and without option
direct generator/receiver
access)
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
1145.1155.82
70
70
100
100
100
115
115
115
115
115
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.209
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
Actual value
R&S ZVA
Max. value
Unit
Measurement
uncertainty
dB
(without option step
attenuator and without option
direct generator/receiver
access)
Test frequency:
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
51.0 GHz
52.0 GHz
53.0 GHz
54.0 GHz
55.0 GHz
56.0 GHz
57.0 GHz
58.0 GHz
59.0 GHz
60.0 GHz
61.0 GHz
62.0 GHz
63.0 GHz
64.0 GHz
65.0 GHz
66.0 GHz
67.0 GHz
1145.1155.82
125
125
120
120
120
120
120
120
120
120
115
115
115
115
115
115
115
115
110
110
110
110
110
110
110
110
110
110
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.210
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
dB
(with option generator or
receiver step attenuator)
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
1145.1155.82
69
69
99
99
99
114
114
114
114
114
124
124
124
124
124
124
124
124
124
124
124
124
124
124
124
124
124
124
124
124
124
124
124
124
124
124
123
123
123
123
123
123
123
123
123
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.211
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
Actual value
R&S ZVA
Max. value
Unit
Measurement
uncertainty
dB
(with option generator or
receiver step attenuator)
Test frequency:
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
51.0 GHz
52.0 GHz
53.0 GHz
54.0 GHz
55.0 GHz
56.0 GHz
57.0 GHz
58.0 GHz
59.0 GHz
60.0 GHz
61.0 GHz
62.0 GHz
63.0 GHz
64.0 GHz
65.0 GHz
66.0 GHz
67.0 GHz
1145.1155.82
123
123
117
117
117
117
117
117
117
117
112
112
112
112
112
112
112
112
107
107
107
107
107
107
107
107
107
107
97
97
97
97
97
97
97
97
97
97
97
97
97
97
97
97
97
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.212
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA67
Parameter
Reference
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
Parameter
Reference
Min. value
Actual value
Max. value
Unit
Measurement
uncertainty
Port __ to Port ___
Dynamic range
Page 1.13
dB
(with options gen. and rec.
step attenuator or with opt.
direct gen./rec. access)
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
1145.1155.82
68
68
98
98
98
113
113
113
113
113
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
121
121
121
121
121
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.213
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
121
121
121
121
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
Port __ to Port ___
Dynamic range
Min. value
Actual value
________
________
________
________
R&S ZVA
Max. value
Unit
'
Measurement
uncertainty
–
–
–
–
dB
Page 1.13
(with options gen. and rec.
step attenuator or with opt.
direct gen./rec. access)
Test frequency:
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
51.0 GHz
52.0 GHz
53.0 GHz
54.0 GHz
55.0 GHz
56.0 GHz
57.0 GHz
58.0 GHz
59.0 GHz
60.0 GHz
61.0 GHz
62.0 GHz
63.0 GHz
64.0 GHz
1145.1155.82
121
121
114
114
114
114
114
114
114
114
109
109
109
109
109
109
109
109
104
104
104
104
104
104
104
104
104
104
94
94
94
94
94
94
94
94
94
94
94
94
94
94
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.214
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Performance Test Report R&S® ZVA67
Reference
Min. value
94
94
94
65.0 GHz
66.0 GHz
67.0 GHz
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
Actual value
Max. value
Unit
–
–
–
________
________
________
Actual value
Measurement
uncertainty
Max. value
Unit
Measurement
uncertainty
dB
(with option gen. or rec. step
attenuator and with opt. direct
gen./rec. access)
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
1145.1155.82
67
67
97
97
97
112
112
112
112
112
122
122
122
122
122
122
122
122
122
122
122
122
122
122
122
122
122
122
122
122
122
122
122
122
122
122
119
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.215
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
Min. value
119
119
119
119
119
119
119
119
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
Actual value
R&S ZVA
Max. value
Unit
Measurement
uncertainty
–
–
–
–
–
–
–
–
________
________
________
________
________
________
________
________
'
Port __ to Port ___
Dynamic range
dB
Page 1.13
(with options gen. or rec. step
attenuator and with opt. direct
gen./rec. access)
Test frequency:
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
51.0 GHz
52.0 GHz
53.0 GHz
54.0 GHz
55.0 GHz
56.0 GHz
57.0 GHz
58.0 GHz
59.0 GHz
60.0 GHz
1145.1155.82
119
119
111
111
111
111
111
111
111
111
106
106
106
106
106
109
106
106
101
101
101
101
101
101
101
101
101
101
91
91
91
91
91
91
91
91
91
91
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.216
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Performance Test Report R&S® ZVA67
Reference
Min. value
91
91
91
91
91
91
91
61.0 GHz
62.0 GHz
63.0 GHz
64.0 GHz
65.0 GHz
66.0 GHz
67.0 GHz
Parameter
Reference
Port __ to Port ___
Dynamic range
Page 1.13
Min. value
Actual value
Max. value
Unit
–
–
–
–
–
–
–
________
________
________
________
________
________
________
Actual value
Measurement
uncertainty
Max. value
Unit
Measurement
uncertainty
dB
(with options gen. and rec.
step attenuator and with opt.
direct gen./rec. access)
Test frequency:
10.0 MHz
20.0 MHz
50.0 MHz
100.0 MHz
200.0 MHz
500.0 MHz
700.0 MHz
750.0 MHz
1.0 GHz
1.5 GHz
2.0 GHz
2.1 GHz
2.5 GHz
3.0 GHz
3.5 GHz
4.0 GHz
4.1 GHz
4.5 GHz
5.0 GHz
5.05 GHz
5.7 GHz
6.0 GHz
6.35 GHz
6.36 GHz
7.0 GHz
7.5 GHz
8.0 GHz
8.1 GHz
9.0 GHz
10.0 GHz
10.2 GHz
11.0 GHz
12.0 GHz
1145.1155.82
66
66
96
96
96
111
111
111
111
111
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.217
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
121
121
121
117
117
117
117
117
117
117
117
117
12.7 GHz
12.8 GHz
13.0 GHz
14.0 GHz
15.0 GHz
16.0 GHz
16.1 GHz
18.0 GHz
19.0 GHz
20.0 GHz
21.0 GHz
22.0 GHz
Port __ to Port ___
Dynamic range
Min. value
Actual value
________
________
________
________
________
________
________
________
________
________
________
________
R&S ZVA
Max. value
Unit
'
Measurement
uncertainty
–
–
–
–
–
–
–
–
–
–
–
–
dB
Page 1.13
(with options gen. and rec.
step attenuator and with opt.
direct gen./rec. access)
Test frequency:
23.0 GHz
24.0 GHz
25.0 GHz
26.0 GHz
27.0 GHz
28.0 GHz
29.0 GHz
30.0 GHz
31.0 GHz
32.0 GHz
33.0 GHz
34.0 GHz
35.0 GHz
36.0 GHz
37.0 GHz
38.0 GHz
39.0 GHz
40.0 GHz
41.0 GHz
42.0 GHz
43.0 GHz
44.0 GHz
45.0 GHz
46.0 GHz
47.0 GHz
48.0 GHz
49.0 GHz
50.0 GHz
51.0 GHz
52.0 GHz
53.0 GHz
54.0 GHz
55.0 GHz
1145.1155.82
117
117
108
108
108
108
108
108
108
108
103
103
103
103
103
103
103
103
98
98
98
98
98
98
98
98
98
98
88
88
88
88
88
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.218
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Performance Test Report R&S® ZVA67
Reference
88
88
88
88
88
88
88
88
88
88
88
88
56.0 GHz
57.0 GHz
58.0 GHz
59.0 GHz
60.0 GHz
61.0 GHz
62.0 GHz
63.0 GHz
64.0 GHz
65.0 GHz
66.0 GHz
67.0 GHz
Parameter
Port __
Receiver Step Atten.
Attenuation Accuracy
Reference 0 dB
Atten.
5 dB
Min. value
Frequ.
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0 GHz
20.0 GHz
22.0 GHz
24.0 GHz
26.0 GHz
28.0 GHz
30.0 GHz
32.0 GHz
34.0 GHz
36.0 GHz
38.0 GHz
40.0 GHz
42.0 GHz
44.0 GHz
46.0 GHz
48.0 GHz
50.0 GHz
52.0 GHz
54.0 GHz
1145.1155.82
Reference
Min. value
Actual value
Max. value
Actual value
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.219
Measurement
uncertainty
–
–
–
–
–
–
–
–
–
–
–
–
________
________
________
________
________
________
________
________
________
________
________
________
Max. value
Page 1.14
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
Unit
Unit
Measurement
uncertainty
dB
0.1 dB
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
E-5
Performance Test Report R&S® ZVA67
Parameter
10 dB
Reference
Min. value
R&S ZVA
Actual value
Max. value
56.0 GHz
58.0 GHz
60.0 GHz
62.0 GHz
64.0 GHz
66.0 GHz
67.0 GHz
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
2
2
2
2
2
2
2
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
Port __
Receiver Step Atten.
Attenuation Accuracy
Reference 0 dB
Page 1.14
Atten.
10 dB
Frequ.
16.0 GHz
18.0 GHz
20.0 GHz
22.0 GHz
24.0 GHz
26.0 GHz
28.0 GHz
30.0 GHz
32.0 GHz
34.0 GHz
36.0 GHz
38.0 GHz
40.0 GHz
42.0 GHz
44.0 GHz
46.0 GHz
48.0 GHz
50.0 GHz
52.0 GHz
54.0 GHz
56.0 GHz
58.0 GHz
60.0 GHz
62.0 GHz
64.0 GHz
66.0 GHz
67.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
20 dB
10 MHz
1.0 GHz
-2
-2
1145.1155.82
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
1.220
Unit
Measurement
uncertainty
dB
0.1 dB
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Parameter
Performance Test Report R&S® ZVA67
Reference
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0 GHz
20.0 GHz
22.0 GHz
24.0 GHz
26.0 GHz
28.0 GHz
30.0 GHz
32.0 GHz
34.0 GHz
36.0 GHz
Port __
Receiver Step Atten.
Attenuation Accuracy
Reference 0 dB
Min. value
Actual value
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
Max. value
Page 1.14
Frequ.
38.0 GHz
40.0 GHz
42.0 GHz
44.0 GHz
46.0 GHz
48.0 GHz
50.0 GHz
52.0 GHz
54.0 GHz
56.0 GHz
58.0 GHz
60.0 GHz
62.0 GHz
64.0 GHz
66.0 GHz
67.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
35 dB
10 MHz
1.0 GHz
2.0 GHz
4.0 GHz
5.8 GHz
8.0 GHz
10.0 GHz
12.0 GHz
14.0 GHz
16.0 GHz
18.0GHz
20.0 GHz
22.0 GHz
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
________
________
________
________
________
________
________
________
________
________
________
________
________
2
2
2
2
2
2
2
2
2
2
2
2
2
1.221
Measurement
uncertainty
dB
0.1 dB
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Atten.
20 dB
1145.1155.82
Unit
E-5
Performance Test Report R&S® ZVA67
Parameter
Reference
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
-2
24.0 GHz
26.0 GHz
28.0 GHz
30.0 GHz
32.0 GHz
34.0 GHz
36.0 GHz
38.0 GHz
40.0 GHz
42.0 GHz
44.0 GHz
46.0 GHz
48.0 GHz
50.0 GHz
52.0 GHz
54.0 GHz
56.0 GHz
58.0 GHz
Port __
Receiver Step Atten.
Attenuation Accuracy
Reference 0 dB
Atten.
35 dB
Frequ.
60.0 GHz
62.0 GHz
64.0 GHz
66.0 GHz
67.0 GHz
1145.1155.82
Min. value
R&S ZVA
Actual value
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
________
Max. value
________
________
________
________
________
1.222
Measurement
uncertainty
dB
0.1 dB
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Page 1.14
-2
-2
-2
-2
-2
Unit
2
2
2
2
2
E-5
FSQ FVREF "Überschrift 2" \* MERGEFORMAT Fehler! Formatvorlage nicht definiert.
R&S ZVA
Performance Test Report R&S® ZVA67
Parameter
Reference
Accuracy
DC meas 1 V
Page 1.15
Min. value
Actual value
Max. value
Pos. Input
-1000 m V
-300 mV
-10 mV
10 mV
300 mV
1000 m V
- 27.5
- 10.0
- 2.75
- 2.75
- 10.0
- 27.5
________
________
________
________
________
________
+ 27.5
+ 10.0
+ 2.75
+ 2.75
+ 10.0
+ 27.5
Neg. Input
-1000 m V
-300 mV
-10 mV
10 mV
300 mV
1000 m V
- 27.5
- 10.0
- 2.75
- 2.75
- 10.0
- 27.5
________
________
________
________
________
________
+ 27.5
+ 10.0
+ 2.75
+ 2.75
+ 10.0
+ 27.5
Accuracy
DC meas 10 V
Page 1.15
Pos. Input
-10.0 V
-3.0 V
-0.1 V
0.1 V
3.0 V
10.0 V
- 0.275
- 0.10
- 0.0275
- 0.0275
- 0.10
- 0.275
________
________
________
________
________
________
+ 0.275
+ 0.10
+ 0.0275
+ 0.0275
+ 0.10
+ 0.275
Neg. Input
-10.0 V
-3.0 V
-0.1 V
0.1 V
3.0 V
10.0 V
- 0.275
- 0.10
- 0.0275
- 0.0275
- 0.10
- 0.275
________
________
________
________
________
________
+ 0.275
+ 0.10
+ 0.0275
+ 0.0275
+ 0.10
+ 0.275
1145.1155.82
1.223
Unit
Measurement
uncertainty
mV
1 mV
V
0.01 V
E-5
R&S ZVA
Table of Contents - Alignment
Table of Contents - Chapter 2 "Alignment"
2 Alignment............................................................................................................. 2.1
Service Menu ...........................................................................................................................2.1
Manual Alignment and Recording Correction Values ..................................................................2.2
Test Equipment ........................................................................................................................2.2
Aligning the Frequency Accuracy.............................................................................................2.4
Aligning the DC Inputs..............................................................................................................2.5
Correction Value Recording and Factory System Error Calibration .........................................2.7
Installation of the Alignment Program ......................................................................................2.7
Checking the Gauge.................................................................................................................2.7
1145.1155.82
I-2.1
E-5
Table of Contents - Alignment
1145.1155.82
R&S ZVA
I-2.2
E-5
R&S ZVA
Manual Alignment and Recording Correction Values
2 Alignment
This chapter describes the alignment of the frequency reference and the recording of correction data
after a board has been replaced.
The following manual alignments or corrections can be performed on the R&S ZVA:
•
•
•
Alignment of the 10-MHz reference oscillator which determines the frequency accuracy of the
R&S ZVA.
Alignment of the DC inputs.
Recording the correction values for the generators and the receivers which determine the
measurement accuracy of the R&S ZVA’s absolute values.
By performing the alignment and recording the correction values, it is possible to ensure that the
R&S ZVA is meeting its specifications by correcting any deviations.
The alignments must be performed within an ambient temperature range of +22 °C to +24 °C after the
appropriate warm-up time.
The R&S ZVA meets its specs and is ready for operation when the alignment has been performed
and/or correction values have been recorded and a system error calibration carried out.
Service Menu
Access to the board-alignment functions is password-protected to prevent unintentional changes to
settings.
Entering the password
MENU
Service Function
System
System Config…
Measurement Wizard <
Print
<
Enter Password:
= Internal Reference
External Reference
Preset
GPIB Address…
Service Function…
External Tools
•
<
Enter password 30473035.
The alignment shall be performed only by appropriately trained personnel because any
changes made have a profound effect on the measurement accuracy of the instrument
.
1145.1155.82
2.1
E-5
Manual Alignment and Recording Correction Values
R&S ZVA
Manual Alignment and Recording Correction Values
In the sequel, the test equipment and the instrument preparations required to manually align the R&S
ZVA and each of the alignments are described.
Preliminary remarks
The analyzer must be allowed to warm up for at least 30 minutes before alignment. This is the only way
of ensuring that the guaranteed data are met.
Test Equipment
Table 2-1
Test equipment for manually aligning the R&S ZVA
Item
Type of equipment
Recommended
specifications
Recommended
model
1
Spectrum analyzer
Counter mode:
Min. resolution: 100 Hz
Max. rel. frequency
deviation:
10-6
R&S FSU26 or
R&S FSU40 or
R&S FSU50 or
R&S FSU67
2
Signal generator
300 kHz to 40 GHz,
Power = -40 dBm to 10 dBm
R&S SML01
R&S SMR40
with Option
R&SSMR-B17
1090.3000.11
1104.0002.40
R&SSMR50
with Option
R&S SMR-B20
and Adapter R&S
FSU/R&S ZVA67
1134.9008.50
2
Signal generator
40 GHz to 67 GHz,
Power = -40 dBm to 0 dBm
R&S Order
No.
Application
Frequency accuracy of
the reference oscillator
Recording correction
values
1104.5233.02
1135.2907.02
Recording correction
values
on R&S ZVA50 and
R&S ZVA67
5009.5507.02
3
Power meter
4
Power sensor
300 kHz to 8 GHz
R&S NRP-Z51
Recording correction
values
on R&S ZVA8
4
Power sensor
10 MHz to 24 GHz
R&S NRP-Z52
Recording correction
values on R&S ZVA24
4
Power sensor
10 MHz to 40 GHz
R&S NRP-Z52
Recording correction
values on R&S ZVA40
4
Power sensor
10 MHz to 50 GHz
R&S NRP-Z56
Recording correction
values on R&S ZVA50
4
Power sensor
10 MHz to 67 GHz
R&S NRP-Z57
Recording correction
values
on R&S ZVA67
5
Power splitter
N, 50 Ohm,
eq < 0.05 (50 MHz to 8 GHz)
Output tracking < 0.15 dB
1145.1155.82
R&S NRP
+ Sensor
Weinschel 1870A -
2.2
Recording correction
values
Recording correction
values on R&S ZVA8
E-5
R&S ZVA
Manual Alignment and Recording Correction Values
Item
Type of equipment
Recommended
specifications
Recommended
model
R&S Order
No.
Application
5
Power splitter
3.5 mm, 50 Ohm,
Output tracking < 0.25 dB
Weinschel 1593
-
Recording correction
values on R&S ZVA24
5
Power splitter
2.92 mm, 50 Ohm,
Output tracking < 0.5 dB
Weinschel 1534
-
Recording correction
values on R&S ZVA40
6
Power splitter
1.85 mm, 50 Ohm,
Output tracking < 0.5 dB
Anritsu SC6778
-
Recording correction
values
on R&S ZVA50,
R&S ZVA67
6
PC with
Pentium, WinXP, WinNT
GPIB-Interface
GR AT-GPIB IEEE4888 IF
PCI National Instruments
Recording correction
values
NI-488 PCI-GPIB
1072.6101.00
7
Alignment Software
R&S ZVAB-Service
8
Power supply
2x 0 to 10 V
9
DC meter
10
Calibration kit
N calibration kit
R&S ZV-Z270
Recording correction
values on R&S ZVA8
10
Calibration kit
3.5 mm calibration kit
R&S ZV-Z235
Recording correction
values on R&S ZVA24
10
Calibration kit
2.92 mm, 50
40 GHz.
. 10 MHz to
R&S ZV-Z229
Recording correction
values on R&S ZVA40
10
Calibration kit
2.40 mm, 50
50 GHz.
. 10 MHz to
R&S ZV-Z224
Recording correction
values on R&S ZVA50
10
Calibration kit
1.85 mm, 50
67 GHz.
. 10 MHz to
ZR&S V-Z218
Recording correction
values
on R&S ZVA67
11
Test cable
Test cable N (m) to N (m).
R&S ZV-Z11
1085.6505.03
Recording correction
values on R&S ZVA8
11
Test cable
Test cable 3.5 mm (m) to
3.5 mm (f).
R&S ZV-Z14
1134.4093.02
Recording correction
values on R&S ZVA24
11
Test cable
Test cable 2.92 mm (m) to
2.92 mm (f)
Order No.
23005066
Huber & Suhner
7
Test cable
Test cable 1.85 mm (m) to
1.85 mm (f)
GORE
EN0CB0CB0240
-
Recording correction
values on R&S ZVA50
(67?)
12
Conn. Cables for DC
Inputs
4-pin mini-DIN plug
R&S ZV-Z71
1164.1005.02
Aligning the DC inputs
1145.1155.82
1302.4460.00
Recording correction
values
Aligning the DC inputs
R&S URE
2.3
0350.5315.03
Aligning the DC inputs
Recording correction
values on R&S ZVA40
E-5
Manual Alignment and Recording Correction Values
R&S ZVA
Aligning the Frequency Accuracy
Test equipment
Spectrum analyzer (section "Test Equipment", item 1):
-9
Error <1 x 10
Test setup:
Connect the spectrum analyzer to the 10-MHz reference output at the
rear of the R&S ZVA.
R&S ZVA settings:
Select internal reference
MENU : System: Reference Internal
Spectrum analyzer settings:
Center frequency: 10 MHz
Span: 200 Hz
Note:
Before the following measurement is performed, the R&S ZVA must
have been switched on for at least 30 minutes to give the reference
oscillator time to warm up.
Measurement:
Measure the frequency with the spectrum analyzer:
Nominal frequency:
Model without OCXO (Option B4) 10 MHz ± 80 Hz
Model with OCXO (Option B4) 10 MHz ± 1 Hz
Alignment without Option R&S ZVAB-B4:
•
Enter Service Function 2.1.1.6.209.0x000000
•
Read off the frequency, e.g. 10.000050 MHz.
•
Change the right-hand segment (corresponding to bit 0 to bit 11) of the data word - e.g. to
000400 - instead of 000000.
•
Read off the frequency again, e.g. 10.000010 MHz.
•
Change the left-hand segment of the data word, until the counter indicates precisely
10.000000 MHz.
Alignment with Option R&S ZVAB-B4:
•
Enter Service Function 2.1.1.6.209.0 x 800000.
•
Read off the frequency, e.g. 10.000005 MHz.
•
Change the left-hand segment (corresponding to bit 12 to bit 23) of the data word - e.g. to
400000 - instead of 800000.
•
Read off the frequency again, e.g. 10.000001 MHz.
•
Change the left-hand segment of the data word, until the counter indicates precisely
10.000000 MHz.
1145.1155.82
2.4
E-5
R&S ZVA
Manual Alignment and Recording Correction Values
Writing data to the hard disk:
Change to computer application
Select path
C:\Documents and Settings\AllUsers\ApplicationData\Rohde&Schwarz\NWA\data\eeprom\
FR\config.ini
Transform data format to decimal
Write decimal data to [ TUNE ]
128_PRETUNE = … (without option R&S ZVAB-B4)
OCXO_TUNE = … (with option R&S ZVAB-B4)
Writing to Eprom:
Select Service Level 2 (see Service Functions)
Set Service Function 3.9.0.2
Aligning the DC Inputs
At the outset, ensure that the correction parameters "Multiplier" M and "Offset" F have been preset to
M=1 and F=0 for both inputs. This can be done using the Service Functions 3.1.2.5 and 3.1.2.2 which
are described below under Service Functions.
Test equipment:
Power supply 2 x 0 to 10 V
DC meter (URE)
Test setup:
DC Meas ± 1 V
DC Meas ± 10 V
Connect DC voltage
+ 1 V…………pin 6, pin 3 (Gnd)
- 1 V…………pin 8, pin 5 (Gnd)
Connect DC voltage:
+ 10 V…………pin 6, pin 3 (Gnd)
- 10 V…………pin 8, pin 5 (Gnd)
Check voltages with the URE and correct if necessary.
R&S ZVA settings:
Measure : DC Inputs : DC Meas ± 1 V
Measurement
Read off the voltages displayed by the R&S ZVA:
Measure : DC Inputs: DC Meas ± 10 V
V1 = positive voltage
V2 = negative voltage
Calculating the corrections:
M -> scaling factor
F -> offset
M = (V1-V2)/2
M = (V1-V2)/20
F = (V1+V2)/(V1-V2)
F = 10x (V1+V2)/(V1-V2)
Pin assignment for DC MEAS connector
1145.1155.82
2.5
E-5
Manual Alignment and Recording Correction Values
R&S ZVA
The values that have been obtained in this way are now written to the hard disk using the Service
Functions described below and then transferred to the EEprom of network controller1.
Example illustrating DC Meas 1 V:
When +1 V is applied, V 1 = 1.023 V is displayed by the R&S ZVA; when -1 V is applied, V2 = -1.011 V
is displayed. The results of the calculation are M = 1.017 and F = 0.0059. The following entries are,
therefore, made:
Select Service Level 2 (see Service Functions).
Set Service Functions (Writing to the hard disk)
3.1.2.5.dc_meas_1V.DcMeasMultiplier.1.017
3.1.2.5.dc_meas_1V.DcMeasOffset.0.0059
etc. for the second measurement input.
Set Service Function (Writing to the EProm)
3.1.2.2
When correction value programming for the two DC voltage measurement inputs has been completed,
end the NWA application and restart.
Check the alignment by applying the four voltages +1 V, -1 V, +10 V and -10 V and, as a further check,
0 V.
Reading the previous DC values:
Select Read in the Service Function Menu
Set Service Functions:
3.1.2.5.dc_meas_1V.DcMeasMultiplier
3.1.2.5.dc_meas_1V.DcMeasOffset
3.1.2.5.dc_meas_10V.DcMeasMultiplier
3.1.2.5.dc_meas_10V.DcMeasOffset
1145.1155.82
2.6
E-5
R&S ZVA
Manual Alignment and Recording Correction Values
Correction Value Recording and Factory System Error Calibration
Required test equipment (see Table 2-1):
• PC with IEC/IEEE bus interface
• R&S ZVAB service program
• Power meter with power sensor
• Signal generator
• Calibration kit
• N-connector test cable
Installation of the Alignment Program
Install the program by double-clicking the setup.exe file.
If you install the program for the second time the install shield will only remove the old installation. You
will have to start the setup.exe again to perform the installation. The tool has been tested with Windows
XP and Windows NT. Connect the PC, R&S ZVA, power meter and signal generator via the IEC/IEEEbus interface.
For a detailed operating description e.g. dealing with
•
•
•
•
Configuration of the Program
Writing Synthesizer Mapping and Shift Data to the Motherboard
Recording Correction Values
Factory System Error Calibration
see the “Usermanual.doc” or “Usermanual.pdf” file that comes with the installation packet and is
installed in the directory “ C:\Program Files\Rohde&Schwarz\ZVAB-Service” on the PC.
Checking the Gauge
It is strongly recommended that every test port of the Vector Network Analyzer is gauged prior to its first use.
The gauge must be recalibrated whenever the connector adapter is changed and should be checked
regularly, using the gauge block, for correct zero between adapter changes.
Table Connector pin depth tolerances
Connector type
Type N (female)
3.5 mm (male)
2.92 mm (male)
2.4 mm (male)
1.85 mm (male)
1 mm (male)
Pin depth
/ mm
5.258
0.000
0.000
0.000
0.000
0.000
Pos. tolerance
/ mm
+0.000
+0.076
+0.050
+0.050
+0.050
+0.050
Neg. tolerance
/ mm
-0.076
+0.000
+0.000
+0.000
+0.000
+0.000
Procedure
1. Ensure the appropriate connector adapter is fitted to the dial gauge.
2. Attach the gauge block to the gauge interface and rotate the dial so that the indication reads zero.
Lock the dial in position by tightening the screw on the side of the dial. Disconnect the gauge block.
3. Mate the connector to be measured to the gauge and note the indication.
4. The connector is "in gauge" if the indication lies between the limits set by the connector specification
(see Table above). For precision type N and 3.5 mm connectors, the calibrated zero indication on the dial
corresponds to one extreme, the other being -76 Wm (-0.003 in) (anti-clockwise on the dial). CAUTION.
Damage to the connector (or the one it is to) may occur if the reading is positive.
5. After use, return the gauge set to its box.
1145.1155.82
2.7
E-5
R&S ZVA
Instrument Construction and Function Description
Table of Contents - Chapter 3 "Repairs"
3
Repairs.......................................................................................................................................3.1
Instrument Construction and Function Description................................................................3.1
Block Diagram ............................................................................................................................3.2
Description of the Block Diagram ...............................................................................................3.4
Board Replacement...................................................................................................................3.21
Board Overview ........................................................................................................................3.22
Replacing Front Module Controller A90 ...................................................................................3.23
Replacing the Lithium Battery on the Front Module Controller.................................................3.26
Replacing Hard Disk A60..........................................................................................................3.30
Replacing LCD A70 and the DC/AC Converter ........................................................................3.31
Replacing Flexible switch board (Keyboard) A16 / Key Pad A15.............................................3.33
Replacing the Front Cover........................................................................................................3.35
Replacing Disk Drive A30 .........................................................................................................3.36
Replacing USB Board A40 .......................................................................................................3.37
Replacing Power Supply A20 ...................................................................................................3.38
Replacing Fuse board A21 .......................................................................................................3.39
Replacing a Fan........................................................................................................................3.40
Replacing Motherboard A10 .....................................................................................................3.41
Replacing a Reflectometer RM8 A510 to 540 ..........................................................................3.44
Replacing a Reflectometer RM8 A510 to 540 ..........................................................................3.44
Replacing Generator Board (ZVA8 only)..................................................................................3.45
Replacing Receiver Board (ZVA8 only)....................................................................................3.46
Replacing the Bridge Unit (ZVA8 only) .....................................................................................3.49
Replacing a Reflectometer RM24 A510 to 540 ........................................................................3.50
Replacing a Reflectometer RM40 and RM50 A510 to 540 ......................................................3.51
Replacing a Reflectometer RM67 A510 to 540 ........................................................................3.52
Replacing the Coupler Unit (ZVA67) ........................................................................................3.54
Replacing the Test Set (ZVA40 only) .......................................................................................3.54
Replacing the Reflectometer Fan .............................................................................................3.55
Replacing Network Controller Board A130, A140 ....................................................................3.57
Replacing Synthesizer Board A150, A160 ...............................................................................3.58
Replacing Frequency Reference Board A100 ..........................................................................3.59
Troubleshooting ........................................................................................................................3.60
Test Equipment and Accessories .............................................................................................3.61
Troubleshooting - Power-up Problems .....................................................................................3.62
Troubleshooting Boot Problems ...............................................................................................3.63
Troubleshooting - Boot Error ....................................................................................................3.64
Troubleshooting with the Selftest .............................................................................................3.65
Checking the Temperature Sensors .........................................................................................3.70
Service Functions .....................................................................................................................3.71
Determining which Boards are defective ..................................................................................3.75
Board Test ................................................................................................................................3.76
1145.1155.82
I-3.1
E-5
R&S ZVA
Instrument Construction and Function Description
3 Repairs
This chapter describes the R&S ZVA’s construction, simple procedures for repairs, troubleshooting and
board replacement. A selftest which checks the diagnostic voltages of the board and indicates limit
violations is provided for troubleshooting and diagnostics.
Chapter 4 of this service manual describes the installation of options and firmware updates.
Instrument Construction and Function Description
The R&S ZVA’s construction is shown schematically by the following block diagrams and the exploded
drawings (see Chapter 5).
The block diagram will help clarify the following function description of the instrument.
1145.1155.82
3.1
E-5
Instrument Construction and Function Description
R&S ZVA
Block Diagram
See also Chapter 5, Annex and Drawings.
BRIDGE PORT 1 (ZVA8)
COUPLER PORT 1 (ZVA24, 40, 50, 67)
GENERATOR
(Driver+Doubler)
PORT 1
PORT 1
15 to 21 MHz
RECEIVER
REF PORT 1
RECEIVER
MEAS PORT 1
NETCON
ANALOG
1
BRIDGE PORT 2 (ZVA8)
COUPLER PORT 2 (ZVA24, 40, 50, 67)
OPTION
GENERATOR
ATTENUATOR
NETCON
DIGITAL
1
CPU
GRAPHICS
DISPLAY
GENERATOR
(Driver+Doubler)
PORT 2
RECEIVER
REF PORT 2
OPTION
RECEIVER
ATTENUATOR
RECEIVER
MEAS PORT 2
SYNTHESIZER
FREQUENCY
REFERENCE
OPTION
OCXO
ZVAB-B4
POWER
SUPPLY
Fig. 3-1 Block diagram of the R&S ZVA8, R&S ZVA24, R&S ZVA40, R&S ZVA50 and R&S ZVA67
two ports
With option direct generator/receiver access on port1,
options generator and receiver attenuator on port2.
1145.1155.82
3.2
E-5
R&S ZVA
Instrument Construction and Function Description
BRIDGE PORT 1 (ZVA8)
COUPLER PORT 1 (ZVA24, 40, 50, 67)
PORT 1
PORT 1
GENERATOR
PORT 1
OPTION
GENERATOR
ATTENUATOR
15 to 21 MHz
RECEIVER
REF PORT 1
OPTION
RECEIVER
ATTENUATOR
RECEIVER
MEAS PORT 1
NETCON
ANALOG
1
BRIDGE PORT 2 (ZVA8)
COUPLER PORT 2 (ZVA24, 40, 50, 67)
NETCON
DIGITAL
1
GENERATOR
PORT 2
PORT 2
RECEIVER
REF PORT 2
RECEIVER
MEAS PORT 2
SYNTHESIZER 2
FREQUENCY
REFERENCE
SYNTHESIZER 1
OPTION
OCXO
ZVAB-B4
CPU
GRAPHICS
DISPLAY
BRIDGE PORT 3 (ZVA8)
COUPLER PORT 3 (ZVA24, 40, 50, 67)
OPTION
GENERATOR
ATTENUATOR
PORT 3
GENERATOR
PORT 3
15 to 21 MHz
RECEIVER
REF PORT 3
OPTION
RECEIVER
ATTENUATOR
Synthesizer
Synthesizer
PORT 4
RECEIVER
MEAS PORT 3
NETCON
ANALOG
2
NETCON
DIGITAL
2
GENERATOR
PORT 4
RECEIVER
REF PORT 4
RECEIVER
MEAS PORT 4
POWER
SUPPLY
Fig. 3-2 Block diagram of the R&S ZVA8, R&S ZVA24, R&S ZVA40, R&S ZVA50 and R&S
ZVA67 four ports
With option generator/receiver attenuator on port1,
option direct generator/receiver access on port2,
options generator/receiver attenuator and direct generator/receiver access on port3.
1145.1155.82
3.3
E-5
Instrument Construction and Function Description
R&S ZVA
Description of the Block Diagram
The block diagrams shown in Fig. 3-1 and Fig. 3-2 apply to the R&S ZVA8, the R&S ZVA24, the R&S
ZVA40, R&S ZVA50 and the R&S ZVA67 two-ports and four-ports.
The ZVA is a vector network analyzer covering 300 kHz to 8 GHz (R&S ZVA8), 10 MHz to 24 GHz
(R&S ZVA24), 10 MHz to 40 GHz (R&S ZVA40), 10 MHz to 50 GHz (R&S ZVA50) or 10 MHz to 67
GHz (R&S ZVA67). All R&S ZVA are available in a two-port or four-port version. The signals (including
the LO signal for the receiver) are generated using one or two synthesizer boards, depending on the
number of ports. The signal processing path comprises a reflectometer board, an IF board, a network
controller and a processor section, comprising a Pentium-PC, I/O interface and graphics board. The
instrument can be expanded to handle future digital and analog requirements by retrofitting options.
The generator signal on R&S ZVA8 (300 kHz to 8 GHz) is generated on synthesizer board 1, amplified
in the generator section of the reflectometer board and then passes via the bridge to the port (port1 to
4) and thus to the DUT. The reference signal (Ref1 to 4) is split in the bridge and fed to the receiver
section (Receiver Ref1 to 4) on the reflectometer board.
The generator signal on R&S ZVA24, R&S ZVA40, R&S ZVA50 and R&S ZVA67 (10 MHz to 24 GHz,
10 MHz to 40 GHz, 10 MHz to 50 GHz, 10 MHz to 67 GHz) is generated on synthesizer board1,
frequency multiplied, filtered and amplified in the generator section of the reflectometer board and then
passes via the coupler to the port (port1 to 4) and thus to the DUT. The reference signal (Ref1 to 4) is
split in the coupler and fed to the receiver section (Receiver Ref1 to 4) on the reflectometer board.
The signal reflected or transmitted by the DUT (Meas1 to 4) is fed to the port, coupled out in the bridge
or coupler unit and fed to the receiver section (Receiver Meas 1 to 4) on the reflectometer board.
The internal reference frequencies are generated on the frequency reference board. The 128-MHz
reference frequency is generated there as an internal device reference.
The following sections describe the various boards in greater detail.
Reflectometer ZVA8
A reflectometer board comprising a bridge unit, a generator section (Generator) and a receiver
section (Receiver) is incorporated in every port (Port1 to 4). These three components are screwed
together to form a compact unit.
Bridge unit
The bridge unit is a resistive coupler which is used to separate the signal going to the DUT from the
signal coming from the DUT. The reference signal (= measure of the signal to the DUT) is also obtained
from the bridge unit. The reference signal provides a reference for relative measurements.
Generator
The generator contains three broadband amplifier stages which boost the signal coming from the
synthesizer to a level > 20 dBm. Limiter diodes protect the output stage from ESDs. A total of three
adjustable attenuators form the setting element to keep the output level constant and to attenuate it
electronically.
1145.1155.82
3.4
E-5
R&S ZVA
Instrument Construction and Function Description
Receiver
The receiver section has two channels (measurement channel and reference channel) and uses single
conversion. Every channel contains a buffer amplifier, for each of the frequency ranges 300 kHz to
4 GHz and 4 GHz to 8 GHz, a mixer with LO amplifiers and an IF amplifier. In the mixer, the input signal
is directly converted to the IF range, approx 15 to 21 MHz. The inputs are protected by limiter diodes.
Reflectometer Unit ZVA24
A reflectometer unit comprising a coupler unit, a generator section (Generator) and a receiver
section (Receiver) is incorporated in every port (Port1 to 4). The Generator and the Receiver are
screwed together to form a compact unit.
Coupler unit
The coupler unit contains a bias-T and two directional couplers. One coupler is used to separate the
signal going to the DUT from the signal coming from the DUT. The reference signal (= measure of the
signal to the DUT) is obtained from the second coupler. The reference signal provides a reference for
relative measurements.
Generator
The generator contains a frequency doubler for the range 8 GHz to 16 GHz, a switchable filter unit, a
second frequency doubler with filter for the range 16 GHz to 24 GHz and a broadband amplifier for the
frequency range 10 MHz to 24 GHz with two adjustable attenuators to keep the output level constant
and to attenuate it electronically.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
10 MHz to 8.0 GHz
---
10 MHz to 8.0 GHz
---
10 MHz to 8.0 GHz
2
4 GHz to 5.05 GHz
x
8.0 GHz to 10.1 GHz
---
8.0 GHz to 10.1 GHz
3
5.05 GHz to 6.35 GHz
x
10.1 GHz to 12.7 GHz
---
10.1 GHz to 12.7 GHz
4
6.35 GHz to 8.0 GHz
x
12.7 GHz to 16.0 GHz
---
12.7 GHz to 16.0 GHz
5
4.0 GHz to 5.0 GHz
x
8.0 GHz to 10.0 GHz
x
16.0 GHz to 20 GHz
6
5.0 GHz to 6.0 GHz
x
10.0 GHz to 12.0 GHz
x
20.0 GHz to 24 GHz
Receiver
The receiver section has two channels (measurement channel and reference channel) and uses single
conversion. The measurement channel contains a buffer amplifier, two mixers for each of the frequency
ranges 10 MHz to 2.5 GHz and 2.5 GHz to 24 GHz, LO amplifiers and an IF amplifier. The reference
channel is identical to the measurement channel without the buffer amplifier. In the mixers, the input
signal is directly converted to the IF range, approx. 15 to 21 MHz. The mixers are used as basic wave
mixers.
The LO signal section contains a frequency doubler for the range 8 GHz to 16 GHz, a switchable filter
unit, a second frequency doubler with filter for the range 16 GHz to 24 GHz and a broadband amplifier
for the frequency range 30 MHz to 24 GHz.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
30 MHz to 8.0 GHz
---
30 MHz to 8.0 GHz
---
30 MHz to 8.0 GHz
2
4 GHz to 8.0 GHz
x
8.0 GHz to 16.0 GHz
---
8.0 GHz to 16.0 GHz
3
4.0 GHz to 6.0 GHz
x
8.0 GHz to 12.0 GHz
x
16.0 GHz to 24.0 GHz
Each of the reflectometers contains a voltage-controlled fan to perform optimum cooling.
1145.1155.82
3.5
E-5
Instrument Construction and Function Description
R&S ZVA
Reflectometer Unit R&S ZVA40
A reflectometer unit comprising a coupler, a generator section (Driver24 and Doubler44) and a
receiver section (Receiver44) is incorporated in every port (Port1 to 4). The generator and the
receiver are screwed together to form a compact unit.
Coupler Unit
The coupler contains a bias-T and two directional couplers. One coupler is used to separate the signal
going to the DUT from the signal coming from the DUT. The reference signal (= measure of the signal
to the DUT) is obtained from the second coupler. The reference signal provides a reference for relative
measurements.
Driver24
The driver contains a frequency doubler for the range 8 GHz to 16 GHz, a switchable filter unit, a
second frequency doubler with filter for the range 16 GHz to 24 GHz and a broadband amplifier for the
frequency range 10 MHz to 24 GHz with two adjustable attenuators to keep the output level constant
and to attenuate it electronically.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
10 MHz to 8.0 GHz
---
10 MHz to 8.0 GHz
---
10 MHz to 8.0 GHz
2
4 GHz to 5.05 GHz
x
8.0 GHz to 10.1 GHz
---
8.0 GHz to 10.1 GHz
3
5.05 GHz to 6.35 GHz
x
10.1 GHz to 12.7 GHz
---
10.1 GHz to 12.7 GHz
4
6.35 GHz to 8.0 GHz
x
12.7 GHz to 16.0 GHz
---
12.7 GHz to 16.0 GHz
5
4.0 GHz to 5.0 GHz
x
8.0 GHz to 10.0 GHz
x
16.0 GHz to 20 GHz
6
5.0 GHz to 6.0 GHz
x
10.0 GHz to 12.0 GHz
x
20.0 GHz to 24 GHz
Doubler44
The doubler contains a frequency doubler for the range 24 GHz to 44 GHz, a switchable filter unit and a
broadband amplifier for the range 10 MHz to 44 GHz.
Range
Frequency range from
driver24
Doubler
Output frequency
1
10 MHz to 24.0 GHz
---
10 MHz to 24.0 GHz
2
12.0 GHz to 14.9 GHz
x
24.0 GHz to 29.8 GHz
3
14.9 GHz to 18.5 GHz
x
29.8 GHz to 37.0 GHz
4
18.5 GHz to 22.0 GHz
x
37.0 GHz to 44.0 GHz
Receiver44
The receiver section has two channels (measurement channel and reference channel). The
measurement channel contains a buffer amplifier, two mixers for each of the frequency ranges 10 MHz
to 2.5 GHz and 2.5 GHz to 44 GHz, LO doublers, LO amplifiers and an IF amplifier. The reference
channel is identical to the measurement channel without the buffer amplifier. In the mixers, the input
signal is directly converted to the IF range, approx. 15 to 21 MHz. In the frequency range 10 MHz to 24
GHz the mixers are used as basic wave mixers (IF = LO – RF). In the range 24 GHz to 44 GHz the
mixer for the upper frequency range works as a harmonic mixer (IF = 3LO – RF).
1145.1155.82
3.6
E-5
R&S ZVA
Instrument Construction and Function Description
The LO signal section contains a frequency doubler for the range 8 GHz to 16 GHz, a switchable filter
unit, a second frequency doubler with filter for the range 16 GHz to 24 GHz and a broadband amplifier
for the frequency range 30 MHz to 24 GHz.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
30 MHz to 8.0 GHz
---
30 MHz to 8.0 GHz
---
30 MHz to 8.0 GHz
2
4 GHz to 8.0 GHz
x
8.0 GHz to 16.0 GHz
---
8.0 GHz to 16.0 GHz
3
4.0 GHz to 6.0 GHz
x
8.0 GHz to 12.0 GHz
---
16.0 GHz to 24.0 GHz
Each of the reflectometers RM1 and RM2 contain two voltage-controlled fans to perform optimum
cooling.
Reflectometer Unit R&S ZVA50
A reflectometer unit comprising a coupler, a generator section (Driver24 and Doubler50) and a
receiver section (Receiver50) is incorporated in every port (Port1 to 4). The generator and the
receiver are screwed together to form a compact unit.
Coupler Unit
The coupler contains a bias-T and two directional couplers. One coupler is used to separate the signal
going to the DUT from the signal coming from the DUT. The reference signal (= measure of the signal
to the DUT) is obtained from the second coupler. The reference signal provides a reference for relative
measurements.
Driver24
The driver is the same as it is used in ZVA40. Frequency range 6 is extended to 25 GHz.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
10 MHz to 8.0 GHz
---
10 MHz to 8.0 GHz
---
10 MHz to 8.0 GHz
2
4 GHz to 5.05 GHz
x
8.0 GHz to 10.1 GHz
---
8.0 GHz to 10.1 GHz
3
5.05 GHz to 6.35 GHz
x
10.1 GHz to 12.7 GHz
---
10.1 GHz to 12.7 GHz
4
6.35 GHz to 8.0 GHz
x
12.7 GHz to 16.0 GHz
---
12.7 GHz to 16.0 GHz
5
4.0 GHz to 5.0 GHz
x
8.0 GHz to 10.0 GHz
x
16.0 GHz to 20 GHz
6
5.0 GHz to 6.25 GHz
x
10.0 GHz to 12.5 GHz
x
20.0 GHz to 25 GHz
1145.1155.82
3.7
E-5
Instrument Construction and Function Description
R&S ZVA
Doubler50
The doubler contains a frequency doubler for the range 25 GHz to 50 GHz, a switchable filter unit and a
broadband amplifier for the range 10 MHz to 50 GHz.
Range
Frequency range from
driver24
Doubler
Output frequency
1
10 MHz to 25.0 GHz
---
10 MHz to 25.0 GHz
2
12.5 GHz to 14.9 GHz
x
25.0 GHz to 29.8 GHz
3
14.9 GHz to 18.5 GHz
x
29.8 GHz to 37.0 GHz
4
18.5 GHz to 25.0 GHz
x
37.0 GHz to 50.0 GHz
Receiver50
The receiver section has two channels (measurement channel and reference channel). The
measurement channel contains a buffer amplifier, two mixers for each of the frequency ranges 10 MHz
to 2.5 GHz and 2.5 GHz to 50 GHz, LO doublers, LO amplifiers and an IF amplifier. The reference
channel is identical to the measurement channel without the buffer amplifier. In the mixers, the input
signal is directly converted to the IF range, approx. 15 to 21 MHz. In the frequency range 10 MHz to 24
GHz the mixers are used as basic wave mixers (IF = LO – RF). In the range 24 GHz to 50 GHz the
mixer for the upper frequency range works as a harmonic mixer (IF = 3LO – RF).
The LO signal section contains a frequency doubler for the range 8 GHz to 16 GHz, a switchable filter
unit, a second frequency doubler with filter for the range 16 GHz to 24 GHz and a broadband amplifier
for the frequency range 30 MHz to 24 GHz.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
30 MHz to 8.0 GHz
---
30 MHz to 8.0 GHz
---
30 MHz to 8.0 GHz
2
4 GHz to 8.0 GHz
x
8.0 GHz to 16.0 GHz
---
8.0 GHz to 16.0 GHz
3
4.0 GHz to 6.0 GHz
x
8.0 GHz to 12.0 GHz
---
16.0 GHz to 24.0 GHz
Each of the reflectometers RM1 and RM2 contain two voltage-controlled fans to perform optimum
cooling.
Reflectometer Unit ZVA67
A reflectometer unit comprising a coupler, a generator section (Driver42 and Doubler67) and a
receiver section (Receiver67) is incorporated in every port (Port1 to 4). The generator and the
receiver are screwed together to form a compact unit.
Coupler Unit
The coupler contains a bias-T and two directional couplers. One coupler is used to separate the signal
going to the DUT from the signal coming from the DUT. The reference signal (= measure of the signal
to the DUT) is obtained from the second coupler. The reference signal provides a reference for relative
measurements.
1145.1155.82
3.8
E-5
R&S ZVA
Instrument Construction and Function Description
Driver42
The driver contains a frequency doubler for the range 12 GHz to 24 GHz with a switchable filter unit and
a second frequency doubler with a switchable filter unit for the range 24 GHz to 42 GHz. Switchable
amplifiers and attenuators and two adjustable attenuators are used to keep the output level constant
and to attenuate it electronically.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
10 MHz to 12.0 GHz
---
10 MHz to 12.0 GHz
---
10 MHz to 12.0 GHz
2
6.0 GHz to 6.75 GHz
x
12.0 GHz to 13.5 GHz
---
12.0 GHz to 13.5 GHz
3
6.75 GHz to 9.0 GHz
x
13.5 GHz to 18.0 GHz
---
13.5 GHz to 18.0 GHz
4
9.0 GHz to 12.0 GHz
x
18.0 GHz to 24.0 GHz
---
18.0 GHz to 24.0 GHz
5
6.0 GHz to 6.75 GHz
x
12.0 GHz to 13.5 GHz
x
24.0 GHz to 27.0 GHz
6
6.75 GHz to 9.0 GHz
x
13.5 GHz to 18.0 GHz
x
27.0 GHz to 36.0 GHz
7
9.0 GHz to 10.5 GHz
x
18.0 GHz to 21.0 GHz
x
36.0 GHz to 42.0 GHz
Doubler67
The doubler contains a frequency doubler for the range 40 GHz to 70 GHz, a switchable filter unit and a
broadband amplifier for the range 10 MHz to 70 GHz.
Range
Frequency range from
driver42
Doubler
Output frequency
1
10 MHz to 41.6 GHz
---
10 MHz to 41.6 GHz
2
20.8 GHz to 27.0 GHz
x
41.6 GHz to 54.0 GHz
3
27.0 GHz to 35.0 GHz
x
54.0 GHz to 70.0 GHz
Receiver67
The receiver section has two channels (measurement channel and reference channel). The
measurement channel contains a buffer amplifier, two mixers for each of the frequency ranges 10 MHz
to 2.5 GHz and 2.5 GHz to 70 GHz, LO doublers, LO amplifiers and an IF amplifier. The reference
channel is identical to the measurement channel without the buffer amplifier. In the mixers, the input
signal is directly converted to the IF signal 17.5 MHz. In the frequency range 10 MHz to 24 GHz the
mixers are used as basic wave mixers (IF = LO – RF). In the range 24 GHz to 70 GHz the mixer for the
upper frequency range works as a harmonic mixer (IF = 3LO – RF).
The LO signal section contains a frequency doubler for the range 12 GHz to 24 GHz, a switchable filter
unit, an adjustable attenuator and a broadband amplifier for the frequency range 30 MHz to 24 GHz.
Range
1145.1155.82
Basic frequency range
from synthesizer
Doubler
Output frequency
1
30 MHz to 12.0 GHz
---
30 MHz to 12.0 GHz
2
6 GHz to 8.15 GHz
x
12.0 GHz to 16.3 GHz
3
8.15 GHz to 12.0 GHz
x
16.3 GHz to 24.0 GHz
3.9
E-5
Instrument Construction and Function Description
R&S ZVA
Each of the reflectometers RM1 and RM2 contain two voltage-controlled fans to perform optimum
cooling.
Network controller
The network controller comprises two boards, the netcon analog and the netcon digital which are
screwed together to form a single unit. The boards are four-channel – in other words, one network
controller is required for two ports (2 measurement channels + 2 reference channels). After A/D
conversion, the network controller performs high-speed digital processing on the IF signals from the
reflectometers.
Netcon analog
The netcon analog board is a 4-channel IF amplifier and one 14-bit A/D converter per channel. The
transmission bandwidth is 13 MHz to 26 MHz. A dither generator is used to linearize the A/D-converter
characteristic. The board also accommodates a temperature sensor which is only used for general
temperature checks and not to correct measurement results.
Netcon digital
The netcon digital board further processes the digitized raw data from the netcon analog board. Speed
considerations mean that digital signal processing is performed in an ASIC which has a clock frequency
of 80 MHz.
The main functions on the board are:
• Mixing to the baseband
• Filter with bandwidths from 1 Hz to 100 kHz in 1/3/5 sequence
• Detectors, PCI interface
• Setting and routine control
The current measured value (sample), the average, the RMS and the Max can be recorded
simultaneously and passed on to the main processor via the PCI-bus. The connection to the PCI-bus is
made via the PCINT-FPGA. A further FPGA "FCON" contains the central section of the procedure
control from measurement point to measurement point and the trigger control. This FPGA is configured
by the main processor.
The A/D converters for ext. DC measurements are also accommodated on the netcon digital board.
Frequency reference
The frequency reference board generates the highly stable and spectrally pure clock signals, required
by the ZVA, which can be phase-locked to external synchronisation signals.
The various function blocks are:
The 128 MHz VCXO (voltage-controlled crystal oscillator) which generates a stable, low-noise
reference frequency for the synthesisers, for the A/D converters and for digital signal processing.
The PLL for phase locking the VCXO signal to an external reference signal or to a 10 MHz OCXO
(oven-controlled crystal oscillator) option.
1145.1155.82
3.10
E-5
R&S ZVA
Instrument Construction and Function Description
The VCO and PLL which generate the clock for the netcon digital board (locked to the 128 MHz VCXO).
The frequency can be varied from 75 MHz to 86 MHz. The VCO frequency is programmable;-the
nominal clock frequency is 80 MHz.
A reference frequency of 10 MHz is standard. If the OCXO is fitted, the OCXO signal is brought out at
the ZVA’s rear panel (10 MHz REF) so that further instruments can be synchronised.
The free-running VCXO (no OCXO, no external reference) can be calibrated using a pre-tune voltage.
If no OCXO is fitted, a 10 MHz signal is still output at the instrument’s rear panel. It is derived from the
80 MHz signal which is divided down to 10 MHz by the divider for the OCXO.
The following are also accommodated on the board:
- A control-CPLD to act as an interface between the serial bus and the board,
- Register for storing divider values,
- D/A converter for pre-tuning the VCXO and OCXO
- An on-board EEPROM for storing board-specific data
- Selftest facilities
OCXO reference (option B4)
As an option, the frequency reference board can be fitted to an OCXO (oven-controlled crystal
oscillator) which considerably improves the phase noise of the reference signal close to the carrier,
short-term stability and long-term stability.
1145.1155.82
3.11
E-5
Instrument Construction and Function Description
R&S ZVA
Synthesizers
The source signals for the generator signals associated with each port and the LO signal for the mixers
on the receiver boards for each of the reflectometers are generated on the synthesizer board. One or
two individual synthesizers are accommodated on a synthesizer board. There are three different
synthesizer types used in the ZVA models:
Synthesizer-LS
to Reflectometer 1
(GEN)
Synthesizer
9 kHz to 8GHz
to Reflectometer 2
(GEN)
to Reflectometer 1
(LO)
Synthesizer
15.625 MHz to
8025 MHz
to Reflectometer 2
(LO)
1145.1155.82
3.12
E-5
R&S ZVA
Instrument Construction and Function Description
Synthesizer-DS
to Reflectometer 1
(GEN)
Synthesizer
9 kHz to 8GHz
to Reflectometer 2
(GEN)
to Reflectometer 3
(GEN)
Synthesizer
9 kHz to 8GHz
1145.1155.82
3.13
E-5
Instrument Construction and Function Description
R&S ZVA
Synthesizer-LO
to Reflectometer 1
(LO)
to Reflectometer 2
(LO)
Synthesizer
15.625 MHz to
8025 MHz
to Reflectometer 3
(LO)
to Reflectometer 4
(LO)
1145.1155.82
3.14
E-5
R&S ZVA
Instrument Construction and Function Description
Synthesizer-12 1305.3020.02
Synthesizer
30 MHz to 12 GHz
LO Reflectometer 1
Synthesizer
30 MHz to 12 GHz
LO Reflectometer 2
Synthesizer
GEN Reflectometer 1
10 MHz to 12 GHz
Synthesizer
GEN Reflectometer 2
10 MHz to 12 GHz
1145.1155.82
3.15
E-5
Instrument Construction and Function Description
R&S ZVA
Synthesizer-12 1305.1702.03
Synthesizer
GEN Reflectometer 1
10 MHz to 12 GHz
Synthesizer
GEN Reflectometer 3
10 MHz to 12 GHz
Synthesizer
10 MHz to 12 GHz
GEN Reflectometer 2
Synthesizer
GEN Reflectometer 4
10 MHz to 12 GHz
1145.1155.82
3.16
E-5
R&S ZVA
Instrument Construction and Function Description
Synthesizer-12 1305.xxxx.04
LO Reflectometer 1
Synthesizer
30 MHz to 12 GHz
LO Reflectometer 3
LO Reflectometer 2
LO Reflectometer 4
Synthesizer
30 MHz to 12 GHz
1145.1155.82
3.17
E-5
Instrument Construction and Function Description
R&S ZVA
The synthesizer models are incorporated as follows in the various ZVA models:
Synthesizer-
LS
1302.4025.02
LS
1302.4025.20
DS
1302.5180.02
LO
1302.4248.02
LO
1302.4248.20
12
1305.3020.02
ZVA8 two-port
2x SRC, 2x LO
--------
--------
--------
--------
--------
ZVA8 four-port
--------
--------
4x SRC
4x LO
--------
--------
ZVA24 two-port
2x SRC, 2x LO
--------
--------
--------
--------
--------
ZVA24 four-port
--------
--------
4x SRC
4x LO
--------
--------
ZVA40 two-port
--------
2x SRC, 2x LO
--------
--------
--------
--------
ZVA40 four-port
--------
--------
4x SRC
--------
4x LO
--------
ZVA50 two-port
--------
2x SRC, 2x LO
--------
--------
--------
--------
ZVA50 four-port
--------
--------
4x SRC
--------
4x LO
--------
ZVA67 two-port
--------
--------
--------
--------
--------
2x SRC, 2x LO
(one board)
ZVA67 four-port
--------
--------
--------
--------
--------
4x SRC, 4x LO
(two boards)
Front unit
The front unit comprises a mounting plate on which the LCD, the flexible switch board and key pad, and
the tachogenerator are accommodated.
The front module controller is mounted in the controller tray in the instrument frame.
LC display
All results and setting information the user requires is displayed on the colour LCD.
The resolution of the LCD is 800 x 600 pixels (SVGA).
The display has an integral cold-cathode tube to provide illumination. The high voltage that is required is
provided by a dedicated DC/AC converter. The converter is mounted on the mounting plate next to the
display and connected to both the display and the controller board via a cable.
Keyboard
The keyboard comprises a flexible switch board and a key pad. They make contact whenever a rubber key
is pressed. The two LEDs for the status display associated with the Standby/On key (yellow for
standby/green for on) are also accommodated on the key pad.
Key detection and LED control are performed via a foil cable connection on the controller board. They are
controlled by means of a matrix method implemented by a special microprocessor on the controller board;
the two LEDs are controlled accordingly. When the instrument is turned off at the mains switch, the
microprocessor saves the status of the Standby/On key.
1145.1155.82
3.18
E-5
R&S ZVA
Instrument Construction and Function Description
Front module controller
The front module controller accommodates all the components that are required on one board - for example,
the processor, memory chips (SIMMs), I/O chips (ISA bus), the lithium battery, IEC/IEEE bus controller, two serial
interfaces (COM1/2), a parallel interface (LPT), LCD graphics controller, external VGA-monitor graphics
interface (Monitor) and a connector for an external keyboard (keyboard PS/2). Also integrated on the
controller board are a floppy controller for an external disk drive and an IDE hard-drive controller.
In the case of the FMR6, the LAN interface is also integrated on the controller board.
Hard disk
The hard disk is screwed to the rear of the tray for the front module controller with a holder and
connected to the board with a flat cable.
Power supply
The power supply produces all the voltages required to power the ZVA. It can be turned off with a
switch on the instrument’s rear panel.
The power supply is a primary-switched power supply with power factor correction (PFC) and standby
circuit (+12 V standby).
On the secondary side, it outputs DC voltages (+3.4 V, +5.2 V, +6.5 V, +8.25 V, +12.25 V, +12 V
standby, -12.25 V).
The control signal RS_PS_ON which is controlled by the front module controller (via the STANDBY/ON
key at the front of the instrument frame), activates the power supply. In the standby mode, the power
supply generates only the 12-V standby voltage to supply a crystal oven and the STANDBY status
display on the front panel.
The secondary voltages are open-proof and short-proof to ground and mutually open-proof and shortproof.
A circuit that prevents overheating is also provided. Overheating is indicated to the front module
controller via a status signal (OT).
Motherboard
The motherboard supplies power to the boards and connects them to the control and data buses. A
number of RF connections are also routed via the motherboard.
As well as straight connections, a number of circuits are accommodated on the motherboard:
Motherboard controller (MBCON)
28 V supply
Preamplifier for the DC measurement inputs
Supply voltage fuses
Rear panel interfaces
Fan control
The MBCON unit acts as an FSU bus-slave:
•
•
•
•
•
to drive the LEDs (instrument front-panel)
to drive the fan in five stages
for two temperature sensors on the motherboard
for an SPI-EEPROM on the motherboard
Furthermore, the software can detect which device (ZVA8 or ZVA24) is present using the MBCON.
1145.1155.82
3.19
E-5
Instrument Construction and Function Description
R&S ZVA
In addition to the voltages delivered by the power supply, +28 V is produced from +12 V on the
motherboard by means of a boosting switching regulator. This voltage is required to operate the OCXO
on the reference board when option B4 is fitted.
Each board has its own fuses for the supply voltages. These fuses are soldered into position on the
board.
All external supply voltages (USB etc.) are protected to prevent shorts.
1145.1155.82
3.20
E-5
R&S ZVA
Board Replacement
Board Replacement
The following section is a detailed description of board replacement. Chapter 5 tells you how to order
spare parts. It contains a list of mechanical parts and their order numbers as well as drawings relating
to board replacement.
Note:
The numbers in brackets are the item numbers in the list of mechanical parts in Chapter 5.
In turn, these item numbers are the same as the item numbers in the drawings relating to
board replacements (also in Chapter 5):
1145.1110 sheet 1 (ZVA Network Analyzer)
1145.1110 sheet 2, 3, 4, 5, 6, 7 (ZVA Network Analyzer)
1305.7002 sheet 1, 2, 3 (ZVA67 Network Analyzer)
1145.1290 sheet 2 (ZVB base instrument, power supply cabeling)
1145.1310 sheet 1, 2 (ZVA base instrument)
1145.1390 sheet 1 (ZVA display unit)
1164.1770 sheet 1 (ZVA Option B4)
1145.3593 sheet 1 (8GHz Bridge)
1145.4177 sheet 1 (RM8)
1145.4283 sheet 1 (RM24)
1145.4319 sheet 1 (RM40)
1305.3413 sheet 1 (RM50)
1305.6241 sheet 1 and 2 (RM67)
1164.0250 sheet 1 to 5 (ZVA8 Option B16)
1164.0267 sheet 1 to 5 (ZVA24 Option B16)
1164.0215 sheet 1 to 5 (ZVA8 Option B21 to B24 and B31 to B34)
1164.0221 sheet 1 to 5 (ZVA24 Option B21 to B24 and B31 to B34)
1164.0409 sheet 1 to 8 (ZVA40 Option B21 to B24 and B31 to B34)
1302.4960.08 sheet 1 (RM Unit ZVB4/8)
1302.5621 sheet 1 (RM44 Blower Attachement)
1145.1155.82
3.21
E-5
Board Replacement
R&S ZVA
Board Overview
Table 3-1
Overview: Board Replacement
Board
Measures taken after replacement
Function test
Front module controller
Check error log
Lithium battery
Check error log
Hard disk
Check error log
LC display / DC/AC converter
Functional test
Flexible switch board (keyboard)/
key pad
Functional test
Alignment
Recording of correction
values
System error calibration
Other
BIOS update
System error calibration
FW update
Front cover
Disk drive
Check the directory structure
USB board
Test with mouse, keyboard
Power supply
Check error log
Fan
Motherboard
Check error log
System error calibration
Alignment DC measurement
inputs
Reflectometer
Check error log
Record correction values
System error calibration
Input connector port 1 to 4
(R&S ZVA8 only)
Check error log
System error calibration
Bridge unit
(R&S ZVA8 only)
Check error log
Record correction values
System error calibration
Coupler unit
(R&S ZVA24, R&S ZVA40,
R&S ZVA50 and R&S ZVA67
only)
Check error log
Record correction values
System error calibration
Reflectometer fan
Check error log
Network controller
Check error log
Record correction values
System error calibration
Alignment DC measurement
inputs
Synthesizer
Check error log
Record correction values
System error calibration
LO divider
Check error log
Record correction values
System error calibration
Frequency reference
Check error log
Alignment
Frequency accuracy
1145.1155.82
3.22
E-5
R&S ZVA
Board Replacement
Replacing Front Module Controller A90
(See Chapter 5, Spare Parts List, Item 580, and drawings 1145.1110, 1145.1310)
The front module controller is located behind the front unit.
Opening the instrument and removing the front unit
Turn off the instrument and disconnect from the mains.
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the 4 screws from the front handles (410), left and right, and take off the front handles.
Remove the countersunk screw (390) next to the display and pull off the front cover (300, 303, 306,
310, 313, 316) forwards
Remove the 2 countersunk screws (610) in the top of the front frame and the 2 in the bottom.
ZVA8: Remove the countersunk screws (168) (2 ), (153), (154), (163), (164)
Pull out the front unit together with the keyboard and display (600, 604) forwards.
The cables to the front module controller are still connected.
Disconnect the cables to the LCD, the DC/AC illumination converter, the key pad (keyboard), the
tachogenerator and, if necessary, the network connection on the front module controller.
N.B.:
When disconnecting cables, be especially careful with the cable to the keyboard. It is a foil
cable and can only be removed when the locking device on the foil-cable connector is
released.
Removing the front module controller
Remove the 10 sems screws (590) in the front module controller and remove the front module
controller in the following way (see Fig. 3-1):
Note:
The insertion force for the front module controller on the motherboard is very large.
The slot in the bottom of the controller tray is provided to facilitate pushing out the front
module controller forwards.
Using a blunt, flat tool, carefully edge the board forwards.
Do not insert the tool too far into the slot; only apply pressure to the board.
To ease the board out, apply light pressure to each and every
Do not bend the board.
1145.1155.82
3.23
slot.
E-5
Board Replacement
Fig. 3-1
R&S ZVA
Removing the front module controller Installing the new front module controller and putting
the instrument back together.
Carefully insert the new front module controller on the motherboard and screw into place with 10
sems screws (590).
Caution:
With type FMR6 1091.2520.00, there is a danger of shorting between board components,
tracks and screws (590). Use suitable insulation.
Reconnect the cables to the front module controller, ensuring correct polarity.
Front Module Controller Typ FMR6
Connector for rotary pulse generator
Controller module
Controller module
Contact side of switching foil (keyboard) up
CPU
Battery
LAN 1 LAN 2
+
Connector for display and
converter adapter board
Fig. 3-2
Location of the edge connectors on the front module controller
Re-insert the front unit into the instrument and secure to the front frame with 4 countersunk screws.
(610).
Fit the following countersunk screws (168) (2 ), (153), (154), (163), (164).
Avoid trapping cables and ensure cabling is tidy..
Replace the front cover (300 to 316) and secure with the countersunk screw (390).
Secure the 2 front handles (410) with the 4 screws.
Fit the termination and the 3.5mm connection cables (only with option ZVAx-B16)
1145.1155.82
3.24
E-5
R&S ZVA
Board Replacement
Putting into operation
Connect the mains cable and turn on at the power on switch. The instrument is now in standby
mode.
Prepare a BIOS disk downloading the required file from https://gloris.rohdeschwarz.com
(Document link: Firm- \ Software) on a floppy disk.
Insert the BIOS disk into the floppy disk drive.
Turn on the instrument and wait for the first beep. Press the DEL key. The instrument should now
display the setup menu.
•
•
•
•
•
•
Select Advanced BIOS Features
Enter
Select First Boot Device
Select Floppy using page up/down key
Press F10 key (save)
Enter
BIOS has now been programmed.
Do not turn the instrument off when the program is running.
Follow the instructions on the screen.
Select Service Level 2 (see Service Functions).
Check the protocol file for errors:
[ INFO : Error Log ]
1145.1155.82
3.25
E-5
Board Replacement
R&S ZVA
Replacing the Lithium Battery on the Front Module Controller
(See Chapter 5, Spare Parts List, Item (582), and drawings 1145.1110, 1145.1290)
The lithium battery is located on the front module controller behind the front unit.
Danger of fire or intoxication
Lithium batteries must not be exposed to high temperatures or fire.
Keep away from children to avoid intoxication.
If the battery is replaced improperly, there is danger of explosion. Only replace the battery with R&S type (See Chapter 5, Spare Parts List, Item 776 for type FMR6).
Lithium batteries are hazardous waste and must be disposed of in dedicated containers. Observe local regulations regarding waste disposal.
Do not short-circuit the battery!
Opening the instrument and removing the front unit
Turn off the instrument and disconnect from the mains.
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the 4 screws from the front handles (410), left and right, and take off the front handles.
Remove the countersunk screw (390) next to the display and pull off the front cover (300, 303, 306,
310, 313, 316) forwards
Remove the 2 countersunk screws (610) in the top of the front frame and the 2 in the bottom.
ZVA8: Remove the countersunk screws (168) (2 ), (153), (154), (163), (164)
Pull out the front unit together with the keyboard and display (600, 604) forwards.
Risk of instrument damage
Be careful when removing the front panel of the instrument because the connecting
cables are still connected to the controller to avoid damage to the instrument.
1145.1155.82
3.26
E-5
R&S ZVA
Board Replacement
Disconnecting cables
When pulling off the connecting cables be careful with the cable connecting to the
keyboard. It is a film cable which can only be disconnected after sliding up the lock of
the film cable plug.
Disconnect the cables to the LCD, the DC/AC illumination converter, the key pad (keyboard), the
tachogenerator and, if necessary, the network connection on the front module controller.
Note:
1145.1155.82
When disconnecting cables, be especially careful with the cable to the keyboard. It is a
foil cable and can only be removed when the locking device on the foil-cable connector
is released.
3.27
E-5
Board Replacement
R&S ZVA
Removing the lithium battery
Carefully lift up and pull out the battery.
Lithium battery 3.4 V (dia. 20 mm * 3 mm) R&S Item No. 0858.2049.00
Note:
Front Module Controller Typ FMR6
Connector for rotary pulse generator
Controller module
Controller module
Contact side of switching foil (keyboard) up
CPU
Battery
LAN 1 LAN 2
+
Connector for display and
converter adapter board
Fig. 3-3
Location of the lithium battery on the front module controller
Installing the new battery and reassembling the instrument
Risk of discharge
Do not short-curcuit the battery.
Insert the battery under the spring in the holder.
N.B.: The positive pole of the battery (+) must be uppermost.
Reinsert the front unit in the instrument and secure to the front frame with 4 countersunk screws
(610).
Refit the countersunk screws (168) (2 ), (153), (154), (163), (164).
Risk of instrument damage
Be careful when replacing the cables. Connect the cables to the proper connectors to
avoid damage to the instrument.
Replace the front cover (300, 303, 306, 310, 313, 316) and screw in the countersunk screw (390).
Refit the 2 front handles (410) using 4 screws.
Fit the termination and the 3.5mm connection cables (only with option ZVAx-B16).
1145.1155.82
3.28
E-5
R&S ZVA
Board Replacement
Putting into operation
Connect the mains cable, turn on at the power switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
1145.1155.82
3.29
E-5
Board Replacement
R&S ZVA
Replacing Hard Disk A60
(See Chapter 5, Spare Parts List, Item 710, and drawings 1145.1110 and 1145.1310)
The hard disk is located between the controller tray and the boards. The spare disk is delivered with the
software pre-installed.
Before removal:
Whenever possible, back up the user data on an external data storage medium.
Opening the instrument and replacing the hard disk
Turn off the instrument, disconnect from the mains, unscrew the 4 rear-panel feet (460) and pull off the
enclosure (400) backwards
Lift off the instrument cover (296) at the top after undoing the countersunk screws (298).
Disconnect the flat cable (715) at the hard disk drive.
Note: Do not pull or push on the flat cable – instead, carefully lever out the connector strip with a
small screwdriver.
Remove the 2 countersunk screws (725) in the hard disk holder (720).
Remove the hard disk (710) and holder (720).
Undo the 4 countersunk screws (730), remove the old hard disk and screw the new hard disk to the
holder (720).
Installing and putting the new hard disk into operation
Refit the hard disk and holder into the instrument using 2 countersunk screws (725).
Note: The bottom of the holder is inserted into a sheet-metal wall.
Connect the flat cable (715) to the hard disk.
Replace the instrument’s top cover (296) and screw back into position with 23 or 28 countersunk
screws (298).
Slide on the enclosure (400) and screw the 4 rear-panel feet (460) back into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Function)
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Perform the factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.30
E-5
R&S ZVA
Board Replacement
Replacing LCD A70 and the DC/AC Converter
(See Chapter 5, Spare Parts List Items 910, 930 and drawings 1145.1110, 1145.1390)
The LCD and the associated DC/AC converter are accommodated on a mounting plate. The connection
to the front module controller is made with cables which should also be replaced individually. The
replacement procedure is as follows:
Opening the instrument and removing the front unit
Turn off the instrument and disconnect from the mains.
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the 4 screws from the front handles (410), left and right, and take off the front handles.
Remove the countersunk screw (390) next to the display and pull off the front cover (300, 303, 306,
310, 313, 316) forwards
Remove the 2 countersunk screws (610) in the top of the front frame and the 2 in the bottom.
ZVA8: Remove the countersunk screws (168) (2 ), (153), (154), (163), (164)
Pull out the front unit together with the keyboard and display (600, 604) forwards.
The cables to the front module controller are still connected
Disconnect the cables to the LCD, the DC/AC illumination converter, the key pad (keyboard), the
tachogenerator and, if necessary, the network connection to the front module controller.
Note:
When disconnecting cables, be especially careful with the cable to the keyboard. It is a
foil cable and can only be removed when the locking device on the foil-cable connector
has been released.
Place the key-side of the front unit on a clean surface.
Removing the DC/AC converter
Disconnect the cable from the display (910) to the DC/AC converter (930).
Disconnect the converter cable (950) to the DC/AC converter (930)
Remove the DC/AC converter (930) by undoing the 2 screws (940)
Removing the LCD
Disconnect the display cable (945) by cutting through the adhesive label(946).
Remove the display connector (1020) after you have undone the two screws (1040).
Disconnect the display cable (1030) at the display (910).
Remove the display (910) after removing the 4 screws (920)
1145.1155.82
3.31
E-5
Board Replacement
R&S ZVA
Installing and putting into operation a new LCD or DC/AC converter
Reinstall the new LCD or new DC/AC converter by reversing the disassembly procedure, refit all
screws and reconnect the cables that have been disconnected (drawing 1145.1390).
When replacing the display (921) or display cable (945), use a new adhesive label (946) to secure
the cabling.
Place the key-side of the front unit on the top of the instrument so that the cables can be connected
to the front module controller.
Carefully connect all cable connectors to the front module controller, ensuring that the polarity is
correct.
Front Module Controller Typ FMR6
Connector for rotary pulse generator
Controller module
Controller module
Contact side of switching foil (keyboard) up
CPU
Battery
LAN 1 LAN 2
+
Connector for display and
converter adapter board
Fig. 3-4
Location of the edge contacts on the front module controller
Reinsert the front unit in the instrument and secure to the front frame with 4 countersunk screws
(610).
Refit the countersunk screws (168) (2 ), (153), (154), (163), (164).
Avoid trapping cables and ensure cabling is tidy.
Replace the front cover (300, 303, 306, 310, 313, 316) and secure with countersunk screw (390).
Refit the 2 front handles (410) using the 4 screws.
Fit the termination and the 3.5mm connection cables (only with option ZVAx-B16).
Connect the mains cable, turn on at the mains switch and press the ON key.
1145.1155.82
3.32
E-5
R&S ZVA
Board Replacement
Replacing Flexible switch board (Keyboard) A16 / Key Pad A15
(See Chapter 5, Spare Parts List, Items 860, 870 and drawings 1145.1110, 1145.1390)
The flexible switch board (keyboard) and key pad are located behind the front cover and the keyboard
frame
Opening the instrument and removing the front unit
Turn off the instrument and disconnect from the mains.
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the 4 screws from the front handles (410), left and right, and take off the front handles.
Remove the countersunk screw (390) next to the display and pull off the front cover (300, 303, 306,
310, 313, 316) forwards
Remove the 2 countersunk screws (610) in the top of the front frame and the 2 in the bottom.
ZVA8: Remove the countersunk screws (168) (2 ), (153), (154), (163), (164)
Pull out the front unit together with the keyboard and display (600, 604) forwards and place it with
the key-side on top of the instrument.
The cables to the front module controller are still connected.
Disconnect the cables to the LCD, the DC/AC illumination converter, the key pad (keyboard), the
tachogenerator and, if necessary, the network connection to the front module controller.
Note:
When disconnecting cables, be especially careful with the cable to the keyboard. It is a
foil cable and can only be removed when the locking device on the foil-cable connector
is released.
Removing the flexible switch board (keyboard) / key pad
Place the front unit with the key-side upwards on a clean surface.
Remove knob (990) from the tachogenerator.
Undo the 10 countersunk screws (890) and remove the keyboard frame (800, 805).
The flexible switch board (860) and the key pad (870) can now be replaced.
Installing a new flexible switch board / key pad and reassembling the instrument
Insert the new flexible switch board (860) into the keyboard frame (800, 805) from behind.
N.B.:
The positioning pins must be inserted in the holes in the keyboard frame.
Place the new key pad (870) on the rear of the flexible switch board (860).
1145.1155.82
3.33
E-5
Board Replacement
Note:
R&S ZVA
Thread the foil cable’s connector through the slot in the mounting tray.
Position the key pad so that the pins on the flexible switch board pass through the holes
in the key pad.
Place the rear of the display unit on the key pad (870).
N.B.:
Position the display unit so that the pins on the flexible switch board pass through the
holes in the mounting tray.
Press the front unit together, with the key-side upwards turn and screw back together again with 10
countersunkl screws (890).
Place the front unit with the key-side on top of the instrument so that the cables can be connected to the
front module controller
Reconnect the cables to the front module controller, ensuring correct polarity.
Front Module Controller Typ FMR6
Connector for rotary pulse generator
Controller module
Controller module
Contact side of switching foil (keyboard) up
CPU
Battery
LAN 1 LAN 2
+
Connector for display and
converter adapter board
Fig. 3-5
Location of the edge contacts on the front module controller
Reinsert the front unit into the instrument and secure to the front frame with 4 countersunk screws
(610).
Refit the countersunk screws (168) (2 ), (153), (154), (163), (164).
Avoid trapping cables and ensure cabling is tidy..
Replace the front cover (300, 303, 306, 310, 313, 316) and secure with the countersunk screw
(390).
Refit the 2 front handles (410) using 4 screws.
Fit the termination and the 3.5mm connection cables (only with option ZVAx-B16).
Connect the mains cable, turn on at the mains switch and press the ON key.
1145.1155.82
3.34
E-5
R&S ZVA
Board Replacement
Replacing the Front Cover
(See Chapter 5, Spare Parts List, Items 300, 303, 306, 310, 313, 316 and drawing 1145.1110)
The front cover is the outermost front panel with lettering. Each instrument type has its own front cover.
Turn off the instrument and disconnect from the mains.
Remove the 4 screws in the front handles (410), right and left, and take off the front handles
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the countersunk screw (390) next to the display and pull off the front cover (e.g. 300)
forwards
Fit the new front cover and reassemble the instrument by reversing the disassembly procedure.
Connect the mains cable, turn on at the mains switch and press the ON key.
1145.1155.82
3.35
E-5
Board Replacement
R&S ZVA
Replacing Disk Drive A30
(See Chapter 5, Spare Parts List, Item 670 and drawings 1145.1110 and 1145.1310)
Opening the instrument and removing the disk drive
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and pull
off the enclosure (400) backwards.
Remove the 2 sems screws (700) and carefully lift out the floppy disk drive (670), together with the
floppy drive holder (680).
N.B.: The floppy cable to the motherboard is still connected.
Disconnect floppy cable (690) on the floppy disk drive.
Installing a new disk drive and reassembling the instrument
Release the floppy disk drive by removing the 3 sems screws (700) from the floppy drive holder
(680) and insert a new floppy disk drive (670) into the floppy drive holder (680).
Connect floppy cable (690) on the floppy disk drive.
Resecure the floppy disk drive (680) from above to the side of the instrument with the fan using 2
sems screws (700).
N.N.: Center the floppy disk drive wrt the cut-out in the front cover.
Slide the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Function test
The instrument boots up and starts the instrument firmware.
Insert a 3 ½ disk with files.
Press the FILE key, then the File Manager softkey and Edit Path.
Enter “ a “ and “ : “ with the screen functions and terminate with the Enter key.
The directory structure of the disk displayed on the screen shows that the floppy disk drive is
operating properly.
1145.1155.82
3.36
E-5
R&S ZVA
Board Replacement
Replacing USB Board A40
(See Chapter 5, Spare Parts List, Item 1050 and drawings 1145.1110 and 1145.1390)
The USB board is located behind the front cover and the keyboard frame next to the ON key.
Opening the instrument and removing the USB-board
Turn off the instrument and disconnect from the mains.
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the 4 screws from the front handles (410), left and right, and take off the front handles.
Remove the countersunk screw (390) next to the display and pull off the front cover (300, 303, 306,
310, 313, 316) forwards
Remove the 2 countersunk screws (610) in the top of the front frame and the 2 in the bottom.
ZVA8: Remove the countersunk screws (168) (2 ), (153), (154), (163), (164).
Pull out the front unit together with the keyboard and display (600, 604) forwards and place it with the
key-side on top of the instrument.
Remove the 2 screws (1070), disconnect the cable and remove the USB board (1050).
Fitting the USB board and reassembling the instrument
Install the new USB board by reversing the removal procedure, replace all screws and connect and
install the relevant cables (drawing 1145.1390).
Insert the front unit back into the instrument and secure to the front frame with 4 countersunk
screws (610).
Refit the countersunk screws (168) (2 ), (153), (154), (163), (164).
Replace the front cover (300, 303, 306, 310, 313, 316) and secure with the countersunk screw
(390).
Refit the 2 front handles (410) using 4 screws.
Fit the termination and the 3.5mm connection cables (only with option ZVAx-B16).
Connect the mains cable, turn on at the mains switch and press the ON key.
Check the USB board: Connect the mouse or keyboard and perform a function check.
1145.1155.82
3.37
E-5
Board Replacement
R&S ZVA
Replacing Power Supply A20
(See Chapter 5, Spare Parts List, Items 790 and drawings 1145.1110, 1145.1290, 1145.1310)
The power supply is installed at the rear of the instrument frame.
Removing the power supply
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) towards the rear.
Remove the 4 screws (792) in the rear panel.
Pull out the power supply unit a little at the rear of the instrument, remove screw (737) and antitouch guard (736).
On the left-hand side of the power supply, pull off the protective conductor cable and fuse board
(735) to the left.
On the right-hand side of the power supply, remove the plug-on connections to the motherboard.
Remove the power supply unit.
Installing the new power supply
Fit the new power supply by reversing the removal procedure
If you refit a power supply 1145.5238, fit the cables from the removed one to the new one (see
drawing 1145.1290)
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors
[ INFO : Error Log ]
1145.1155.82
3.38
E-5
R&S ZVA
Board Replacement
Replacing Fuse board A21
(See Chapter 5, Spare Parts List, Item 735, and drawings 1145.1110, 1145.1290)
The fuse board is installed on the left-hand side of the power supply.
Removing the power supply and the fuse board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the 4 screws (757) in the rear panel.
Pull out the power supply unit a little at the rear of the instrument, remove screw (737) and antitouch guard (736).
On the left-hand side of the power supply, pull off the fuse board (735) to the left.
Disconnect the two mains cables from the fuse board.
Fitting the new fuse board and the power supply
Connect the mains cables to the fuse board and refit the fuse board to the power supply.
Secure the anti-touch guard (736) with screw (737).
Reinstall the power supply by reversing the removal procedure.
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors
[ INFO : Error Log ]
1145.1155.82
3.39
E-5
Board Replacement
R&S ZVA
Replacing a Fan
(See Chapter 5, Spare Parts List, Item 15 and drawings 1145.1110, 1145.1310)
The fans, three in all, are located behind the right-hand side panel.
Opening the instrument and removing the fan
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and pull
off the enclosure (400) backwards.
Lift off the top instrument cover (296) after undoing the countersunk screws (298).
For replacing the fan located near by the front remove the 2 sems screws (700) and carefully lift out
the floppy disk drive (670), together with the floppy disk holder (680).
Disconnect the fan cable on the motherboard.
Remove fan (15) by undoing the 4 fan screws (16).
Fitting a new fan and reassembling the instrument
Install the fan using the 4 fan screws.
N.B.:The arrows on the fan show the installation position. The fan blows air into the instrument.
Route the fan cable so that it cannot get caught in the fan.
Connect the fan cabling on the motherboard X35, X36 and X37 (FAN).
Refit the top instrument cover (296) with countersunk screws (298).
Connect the mains cable, turn on at the mains switch and press the ON key.
Check that all three fans are operating correctly (fans are blowing air into the instrument).
Turn off the instrument and disconnect the mains cabling again.
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
1145.1155.82
3.40
E-5
R&S ZVA
Board Replacement
Replacing Motherboard A10
(See Chapter 5, Spare Parts List, Item 510 and drawings 1145.1110, 1145.1310)
The motherboard is located on the base of the instrument.
N.B.:
The motherboard can only be replaced at R&S service centers.
Opening the instrument and removing the motherboard
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Lift off the top instrument cover (296) after undoing the countersunk screws (298).
Extract the top boards: Use ejector lever for the synthesizer and network controller, hold the
frequency reference by the enclosure.
Remove the power supply (550).
•
Remove the 4 screws (757) in the rear panel.
•
Pull out the power supply unit a little at the rear of the instrument, remove screw (737) and antitouch guard (736).
•
On the left-hand side of the power supply, pull off the protective conductor cable and the fuse
board (735) to the left.
•
On the right-hand side of the power supply, pull off the plug-in connections to the motherboard.
•
Remove the power supply unit.
Remove the 4 screws in the front handles (410), right and left, and take off the front handles.
Remove the countersunk screw (390) next to the display and pull off the front cover (300, 303, 306,
310, 313, 316) forwards.
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the 2 countersunk screws (610) in the top of the front frame and the 2 in the bottom.
Remove the countersunk screws (168) (2 ), (153), (154), (163), (164).
Pull out the front unit together with the keyboard and display (600, 604) forwards.
The cables to the front module controller are still connected.
Disconnect the cables to the LCD, the DC/AC illumination converter, the key pad (keyboard), the
tachogenerator and, if necessary, the network connection to the front module controller.
Note:
When disconnecting cables, be especially careful with the cable to the keyboard. It is a
foil cable and can only be removed when the locking device on the foil-cable connector
is released.
Remove the front module controller (for instructions see “Replacing Front Module Controller A90“)
1145.1155.82
3.41
E-5
Board Replacement
R&S ZVA
Place the instrument on its top and remove the instrument’s base cover (297) by undoing the
screws (299).
Undo the RF cabling from the reflectometers (165, 170, 175) to the LO divider (125) and to the
motherboard.
Release the 50-pin flat cable and disconnect from the reflectometers
Remove screws (151, 156, 161) and take out the reflectometers.
Undo RF cabling at the LO divider (125).
Disconnect the 12-pin flat cable from the LO divider
Remove screws (127) (2 in the strut, 4 in the rear panel) and take out the LO divider together with
plate (126)
Undo the screws holding the connectors on the rear panel:
• The 6 hexagonal nuts and washers for the BNC connectors.
• 2 hexagonal bolts (530, 540) each for the monitor interface and the user-control interface.
• 2 hexagonal screws (550) each for the USB interface and in the dummy panel (555).
Remove the 3 screws (144) each for the left and right side panels and the 2 screws (143) in the
center and take out both motherboard rails (140, 141).
Disconnect any cabling still on the motherboard (fan, floppy, IEC-bus, etc.).
Remove the 14 screws holding the motherboard (520) and take out the motherboard.
Remove the RF and IF cables using the tool 11W 101-000 (Rosenberger).
1145.1155.82
3.42
E-5
R&S ZVA
Board Replacement
Installing the motherboard and reassembling the instrument
N.B.:
The motherboard is the passport of the instrument and unique for every unit.
The Eprom on the motherboard contains the serial No. of the instrument.
Pre-configured motherboards are not available.
Install the new motherboard by reversing the removal procedure.
N.B.:
Install the motherboard carefully to prevent any damage to components.
Lettering indicates where cables are to be connected.
Reinstall the front module controller, front unit, power supply, boards and cables, instrument covers,
enclosure and rear-panel feet by reversing the disassembly procedure.
Connect the mains cable, turn on at the mains switch and press the ON key.
For writing motherboard data to the EPROM please contact the service center in Munich.
Select Service Level 2 (see Service Functions).
Check the protocol file for errors: [ INFO : Error Log ]
Align the DC inputs (see Aligning the DC Inputs in chapter 2)
Write synthesizer mapping and shift data to the motherboard EPROM (see Correction Value
Recording in chapter 2)
1145.1155.82
3.43
E-5
Board Replacement
R&S ZVA
Replacing a Reflectometer RM8 A510 to 540
(See Chapter 5, Spare Parts List, Items 150, 160 and drawing 1145.1110)
The boards are located under the motherboard.
Opening the instrument and removing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the bottom instrument cover (297) after undoing the screws (299).
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the screws (153), (154), (163), (164) in the front of the instrument next to the port
connector and (168) in case of port 4.
Disconnect the source cable, the LO cable, the two IF cables and the 50-pin control cable from the
reflectometer.
Remove the 2 screws (151, 161) at the end of the reflectometer and take out the reflectometer
Installing the board and reassembling the instrument
Insert the new board into the instrument and reconnect any cables that have been disconnected
N.B.: Use the lettering on the motherboard as an aid.
Screw in the screws (153, 154, 163, 164, 168) in the front of the instrument.
Screw in the 2 screws (151, 161) in the end of the reflectometer.
Fit the instrument base cover (297) and secure with screws (299).
Slide the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Recording Correction Values in chapter
2).
Perform the factory system error calibration (see Factory System Error Calibration in chapter 2).
1145.1155.82
3.44
E-5
R&S ZVA
Board Replacement
Replacing Generator Board (ZVA8 only)
(See Chapter 5, Spare Parts List, Item 110 and drawing 1302.4960.08)
Opening the instrument and removing the board
Remove the reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Remove the cover (130)
Remove the fan cable
Pull off the generator board (110)
Installing the board and reassembling the instrument
Fit the new generator board (110)
Reconnect the fan cable
Fit the cover (130)
Reinstall the reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Recording Correction Values in chapter
2).
Perform the factory system error calibration (see Factory System Error Calibration in chapter 2).
1145.1155.82
3.45
E-5
Board Replacement
R&S ZVA
Replacing Receiver Board (ZVA8 only)
(See Chapter 5, Spare Parts List, Item 120, 125 and drawing 1302.4960.08)
Opening the instrument and removing the board
Remove the reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Remove the cover (150)
Pull off the receiver board (120, 125)
Installing the board and reassembling the instrument
Fit the new receiver board (120, 125)
Fit the cover (150)
Reinstall the reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Recording Correction Values in chapter
2).
Perform the factory system error calibration (see Factory System Error Calibration in chapter 2).
1145.1155.82
3.46
E-5
R&S ZVA
Board Replacement
Replacing Generator and Receiver Cover (ZVA8
only)
(See Service Circular 10028 and Chapter 5, Spare Parts List, Items 130, 150 and drawing
1302.4960.08)
Opening the instrument and removing the cover
Remove the reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Remove the RM mount (200), 4 screws (210)
Remove the covers (130, 150)
Installing the cover and reassembling the instrument
Fit the new covers (130, 150)
Refit the RM mount (200)
Reinstall the reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the receiver correction data (see Recording Correction Values in chapter 2).
Perform the factory system error calibration (see Factory System Error Calibration in chapter 2).
1145.1155.82
3.47
E-5
Board Replacement
R&S ZVA
Replacing the Inner Conductor of a Port Connector (ZVA8
only)
(See Chapter 5, Spare Parts List, Item 110, and drawings 1145.1110, 1145.4177, 1145.3593)
Opening the instrument and removing the reflectometer
Remove the Reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Replacing the inner conductor
Unscrew the N outer conductor with a spanner (narrow, SW 14mm) and take out inner conductor
unit.
N.B.: Ensure that the centring disk (135) is also removed.
Carefully insert the new inner conductor in the bridge unit enclosure and screw back the N outerconductor (lock with Loctite 262, mount with torque 3.5 Nm).
Reassembling the instrument
Reinstall the Reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Check the gauge (see Checking the Gauge in chapter 2)
Perform factory system error calibration (see Factory System Error Calibration in chapter 2).
1145.1155.82
3.48
E-5
R&S ZVA
Board Replacement
Replacing the Bridge Unit (ZVA8 only)
(See Chapter 5, Spare Parts List, drawings 1145.1110, 1145.4177, Item 100)
Opening the instrument and removing the reflectometer
Remove the Reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Removing the bridge unit
Loosen the MEAS, REF and GEN cables (310, 320, 300) at both ends and disconnect at the bridge
unit.
N.B.: When loosening support the cable with a 7mm spanner!
Remove the 3 screws (160) and carefully pull the bridge unit off the reflectometer.
Remove the 2 screws (240) and remove the plate (230).
Fitting the new bridge unit
Secure plate (230) to the new bridge unit using the 2 screws (240).
Carefully place the bridge unit on the reflectometer and secure with 3 screws (160).
Screw the MEAS- REF and GEN cables (310, 320, 300) to the bridge unit, and then tighten at both
ends.
N.B.: When tightening with a 7 mm spanner support the cable.
Reassembling the instrument
Reinstall the Reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
Check the gauge (see Checking the Gauge in chapter 2)
Record generator and receiver correction data (see Recording Correction Data).
Perform factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.49
E-5
Board Replacement
R&S ZVA
Replacing a Reflectometer RM24 A510 to 540
(See Chapter 5, Spare Parts List, Items 180, 190, 200 and drawings 1145.1110, 1145.4283)
Opening the instrument and removing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the bottom instrument cover (297) after undoing the 12 countersunk screws (299).
Remove 3.5mm connection cables (only with option ZVA24-B16)
Disconnect the three cables to the coupler, the LO cable, the two IF cables and the 50-pin control
cable from the reflectometer.
Loosen the captive screws (see 1145.1110.01 sheet 4 / 5) and take out the reflectometer.
Installing the board and reassembling the instrument
Insert the new board into the instrument.
Screw in the captive screws.
Reconnect any cables that have been disconnected.
Fit the 3.5mm connection cables (only with option ZVA24-B16).
Fit the instrument base cover (297) and secure with screws (299).
Slide the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Recording Correction Values).
Perform the factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.50
E-5
R&S ZVA
Board Replacement
Replacing a Reflectometer RM40 and RM50 A510 to 540
(See Chapter 5, Spare Parts List, Items 209, 222, 230, 232 and drawings 1145.1110, 1145.4319,
1305.3413)
The boards are located under the motherboard.
Opening the instrument and removing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the bottom instrument cover (297) after undoing the 12 countersunk screws (299).
Disconnect the three cables to the coupler, the LO cable, the two IF cables and the 50-pin control
cable from the reflectometer.
Loosen the captive screws (see 1145.4319, 1305.3413) and take out the reflectometer.
Installing the board and reassembling the instrument
Insert the new board into the instrument.
Screw in the captive screws.
Reconnect any cables that have been disconnected.
Fit the instrument base cover (297) and secure with screws (299).
Slide the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Recording Correction Values).
Perform the factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.51
E-5
Board Replacement
R&S ZVA
Replacing a Reflectometer RM67 A510 to 540
(See Chapter 5, Spare Parts List, Items 300 and 350 and drawing 1305.7002)
The boards are located under the motherboard.
Opening the instrument and removing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the bottom instrument cover (297) after undoing the 12 countersunk screws (299).
Disconnect the three cables to the coupler, the LO cable, the two IF cables and the 50-pin control
cable from the reflectometer.
Loosen the captive screws (see1305.7002) and take out the reflectometer.
Installing the board and reassembling the instrument
Insert the new board into the instrument.
Screw in the captive screws.
Reconnect any cables that have been disconnected.
Fit the instrument base cover (297) and secure with screws (299).
Slide the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Recording Correction Values).
Perform the factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.52
E-5
R&S ZVA
Board Replacement
Replacing the Coupler Unit (ZVA24, ZVA40, ZVA50)
(See Chapter 5, Spare Parts List, item 230 and drawing 1145.1110)
Opening the instrument and removing the coupler
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the instrument base cover (297) after undoing the screws (299).
Disconnect the 3 RF cables and the bias cable from the coupler
Remove the 3.5mm connection cables (only with option ZVA24-B16).
Remove the frontcover
Remove the screws (182, 186, 202, 206) in the front of the instrument next to the port connector
and take out the coupler.
Fitting the new coupler unit and reassembling the instrument
Insert the coupler into the instrument and screw in the 4 screws (181, 186, 220).
Reconnect the 3 RF cables and the bias cable.
Fit the 3.5mm connection cables (only with option ZVA24-B16).
Fit the instrument base cover (297) and secure with 12 countersunk screws (299).
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record generator and receiver correction data (see Recording Correction Data).
Perform factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.53
E-5
Board Replacement
R&S ZVA
Replacing the Coupler Unit (ZVA67)
(See Chapter 5, Spare Parts List, item 245 and drawings 1305.7002 and 1305.6241)
Opening the instrument and removing the coupler
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the instrument base cover (297) after undoing the screws (299).
Disconnect the 3 RF cables and the bias cable from the coupler
Remove the 3.5mm connection cables (only with option ZVA24-B16).
Remove the frontcover
Remove the screws (182, 186, 202, 206) in the front of the instrument next to the port connector
and take out the coupler.
Fitting the new coupler unit and reassembling the instrument
Insert the coupler into the instrument and screw in the 4 screws (181, 186, 220).
Reconnect the 3 RF cables and the bias cable.
Fit the 3.5mm connection cables (only with option ZVA24-B16).
Fit the instrument base cover (297) and secure with 12 countersunk screws (299).
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record generator and receiver correction data (see Recording Correction Data).
Perform factory system error calibration (see Factory System Error Calibration).
Replacing the Test Set (ZVA40 only)
N.B.:
In case of defective Test Set please contact the Central Service in Munich.
1145.1155.82
3.54
E-5
R&S ZVA
Board Replacement
Replacing the Reflectometer Fan
(See Chapter 5, Spare Parts List, Item 100, 190 and drawings 1145.1110, 1145.4177, 1145.4283,
1302.5621)
ZVA8 and ZVA24 only:
Remove the reflectometer (see chapter Replacing a Reflectometer RMxx A510 to A540)
Replacing the fan
Disconnect the fan cable at the reflectometer.
Undo the 4 holding screws (110,194) and remove the fan.
Insert the new fan (ZVA8: cable outlet to the outside, ZVA24: cable outlet to the inside).
Screw back the 4 screws (110, 194) and washers (120, 130, 192, 193).
Reassembling the instrument
Reinstall the reflectometer (see chapter Replacing a Reflectometer RMxx A510 to A540)
Connect the mains cable, turn on at the mains switch and press the ON key.
Check that the fan is operating.
Turn off the instrument again and disconnect from the mains.
Fit the instrument base cover (297) and secure with 12 countersunk screws (299).
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Reconnect the mains cable, turn on at the mains switch. The instrument is now in the standby
mode.
ZVA40, ZVA50 and ZVA67 only:
Remove the cover plate (260) undoing 12 screws (261) and 4 screws (212)
Remove blower attachement (210) undoing 2 screws (211)
Replacing the fan
Disconnect the fan cable at the reflectometer.
Remove the fan.
Insert the new fan (cable outlet to the inside of the instrument) and cut the rubber pins (see
1302.5621).
Connect the fan cable to the reflectometer and reinstall the blower attachement (210).
1145.1155.82
3.55
E-5
Board Replacement
R&S ZVA
Reassembling the instrument
Reinstall the cover plate (260)
Connect the mains cable, turn on at the mains switch and press the ON key.
Check that the fan is operating.
Turn off the instrument again and disconnect from the mains.
Fit the instrument base cover (297) and secure with 12 countersunk screws (299).
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Reconnect the mains cable, turn on at the mains switch. The instrument is now in the standby
mode.
1145.1155.82
3.56
E-5
R&S ZVA
Board Replacement
Replacing Network Controller Board A130, A140
(See Chapter 5, Spare Parts List, Items 100, 105 and drawing 1145.1010)
The board is in the upper section of the instrument.
Opening the instrument and removing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Lift off the instrument top cover (296) after undoing the screws (298).
Extract the network controller using the ejector lever
Fitting the board and reassembling the instrument
Fit the new board in the instrument.
Refit the top instrument cover (296) with screws (298).
Slide the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the receiver correction data (see Recording Correction Values).
Perform factory system error calibration (see Factory System Error Calibration).
Align the DC inputs (see Aligning the DC Inputs).
1145.1155.82
3.57
E-5
Board Replacement
R&S ZVA
Replacing Synthesizer Board A150, A160
(See Chapter 5, Spare Parts List, Items 110, 112, 113, 115 and drawing 1145.1110)
The board is located in the upper section of the instrument.
N.B.:
Synthesizers with part numbers 1145.xxxx or 1300.xxxx are no longer available. In case of
defect please contact the Central Service in Munich.
Opening the instrument and removing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Lift off the instrument top cover (296) after undoing the screws (298).
Extract the synthesizer with the ejector lever.
Installing the board and reassembling the instrument
Insert the new board into the instrument.
Refit the instrument top cover (296) securing with the screws (298).
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Install firmware update, if necessary (version U 1.78).
Install synthesizer mapping (see Correction Value Recording)
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Correction Value Recording).
Perform factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.58
E-5
R&S ZVA
Board Replacement
Replacing Frequency Reference Board A100
(See Chapter 5, Spare Parts List, Item 120 and drawings 1145.1110, 1164.1770)
Opening the instrument and replacing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Lift off the instrument top cover (296) after undoing the screws (298).
Extract the frequency reference board (120).
Installing the board and reassembling the instrument
Insert the new board into the instrument
Refit the instrument top cover (296) with the screws (298).
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
1145.1155.82
3.59
E-5
Troubleshooting
R&S ZVA
Troubleshooting
The instructions in this manual describe troubleshooting down to the board level. Any defective boards
can then be replaced and the instrument put back into operation. A selftest which checks the board
diagnostic voltages and displays limit violations is provided to facilitate troubleshooting and diagnosis.
We recommend that you return your instrument to the technical specialists at an R&S service facility for
board replacement and any further repairs that may be needed (see the address list at the beginning of
this manual).
Risk of damage to the boards
Be careful not to cause short circuits when measuring voltages at pins placed close
together!
Do not plug or unplug boards prior to disconnecting them from the AC supply.
The R&S ZVA has the following facilities to simplify diagnosis:
• Selftest
• Service functions
The first thing to do if you encounter any problems is to check if any connection
(cables, edge connectors etc.) are damaged or even incorrectly inserted.
1145.1155.82
3.60
E-5
R&S ZVA
Troubleshooting
Test Equipment and Accessories
Item.
Instrument type
Recommended features
1
DC meter
2
Power supply
0 to 10 V
3
Spectrum analyzer
Frequency range 0 to 40 GHz
Recommende
d model
R&S Order
No.
R&S URE
0350.5315.02 1
R&S FSU 40
Qty.
1
(R&S FSU 50)
(R&S FSU 67)
1
4
Power meter
(if FSU50 or FSU67
not available)
4
Power sensor
10 MHz to 67 GHz
R&S NRP-Z57
5
Test cable
0.6 m long
K male to K female
-
5
Test cable
Test cable 1.85 mm (f) to 1.85 mm (m)
GORE
EN0CB0CB024
0
5
Test cable
6
Adapter cable
1 m long
SMP male to SMA male
-
1129.8259.00 1
7
Adapter cable
0.5 m long
SMP male to SMP male
-
1129.8265.00 1
8
SMA cable
0.5 m long
SMA male to SMA male
-
1142.5895.00 2
9
SMA cable
1 m long
SMA male to SMA male
-
1142.5889.00 2
10
BNC cable
1 m to 2 m long
BNC male to BNC male
-
e.g.
1
1100.8850.00
11
Adapter
SMA female to N male
-
4012.5837.00 2
12
Adapter
N male to BNC female
-
0118.2812.00 1
13
Termination
SMA termination. 50 V male
-
0249.7823.00 3
14
Calibration kit
1.85mm, 50
R&S ZV-Z218
5011.6571.02 1
15
R&S SMP adapter
SMP female to SMP female
-
1093.6869.00 1
16
Adapter board
Extension 150 mm high, 48 pins, 2 mm
pitch
-
1100.3542.02 1
4-pin mini-DIN plug
R&S ZV-Z71
1164.1005.02 1
17
Conn. Cables for
DC Inputs
18
Cable tool
1145.1155.82
R&S NRP
+ Sensor
. DC to 67 GHz.
Rosenberger
11W 101-000
3.61
1306.4688.00 1
1
1
E-5
Troubleshooting
R&S ZVA
Troubleshooting - Power-up Problems
•
Fault: It is not possible to turn on the ZVA.
Action
Check mains switch on the rear panel
Check LED is yellow (standby)
Turn on instrument. Check LED is green
•
Cause of fault / remedy
Mains switch OFF: Turn on at mains switch.
LED does not come on:
Measure voltage at X92.C23
(Front module controller):
Nom. value: +13.5 V ± 1V
Nom. value reached: Fault in key pad or controller.
No voltage:
Power supply defective or short to12 V standby.
LED does not come on:
Measure the PWR-ON signal at power supply
X92.B24:
< 1V for ON
Voltage > 1V: Key pad or controller defective.
Fault: Fan not working.
Action
Check voltage at connector:
X35, X36, X37 pin 3:
nom. value 12V
Cause of fault / remedy
If no voltage can be measured the fan fuse may be
defective (F12, F62, F63)
Select Service Function
Set Service Level 1
Set Service Function 2.5.0.11.1.5
(max. fan speed)
Check voltage at connector:
X35, X36, X37 pin 3:
nom. value 0.9V
1145.1155.82
3.62
E-5
R&S ZVA
Troubleshooting
Troubleshooting Boot Problems
•
Fault: ZVA does not start the measurement application.
The first action the ZVA performs after power-up is booting BIOS for the processor. When the processor
has been successfully initialised, the Windows XP start-up procedure begins. Then, the measurement
application is loaded as an autostart program.
If there are errors during the boot phase, messages indicate possible defects.
The message “No System Disk or Disk error…” indicates that the hard disk data is corrupt. If this is the
case, replace the hard disk.
If the operating system on the hard disk has been corrupted and so cannot be loaded correctly,
Windows XP outputs a “blue screen”.
This screen summarizes all the key information about the internal status of the processor.
1145.1155.82
3.63
E-5
Troubleshooting
R&S ZVA
Troubleshooting - Boot Error
If the message below appears on the screen when the boot procedure has been completed,
Warning: Boot error occurred. For details browse Error Log file.
the cause of the error can be found in the Error-Log file.
INFO
Setup
Info
Press the Error Log softkey.
The results are displayed on the screen.
Hardware
Info
Selftest
Error
Log
OPTION
OCXO
ZVAB-B4
Del Error
Log
Cause of error: Data cannot be read from one or more boards.
When the instrument is booted, all the calibration data that is required must be written to the processor’s
RAM.
When the NWA application is started, the entry on the hard disk is compared with the Eprom data on the
board. If the data matches, the data is loaded from the hard disk into RAM. If there is not a match, the Eprom
data is written to the hard disk and then loaded into RAM.
If the data at the specified address cannot be read, a check is made in Config.ini to check if the board in
question should be present. If so, the board is simulated (i.e. if this board is present and is functioning
physically, the instrument will function) and an entry is made in the ErrorLog file.
If a board must always be physically present, (frequency reference, synthesizer1, NetworkControler1,
reflectometer1, reflectometer2), an error message is output.
See: Troubleshooting with the Selftest
1145.1155.82
3.64
E-5
R&S ZVA
Troubleshooting
Troubleshooting with the Selftest
The selftest is used to check supply voltages to the boards, including voltages generated on the boards
themselves. On the frequency reference board, two clock signals (128 MHz and ADC-CLK) are also
measured.
Starting the selftest:
• Select Service Level 2 (see Service Functions) – this means that the temperature sensor readings
are displayed and tighter voltage tolerances used.
• Call the selftest in the INFO menu:
INFO
Setup
Info
Hardware
Info
Start the selftest with the Selftest softkey.
The selftest results are displayed on the
screen.
Selftest
Error
Log…
Del Error
Log
In the selftest result-table, an abbreviation is used for every board designation:
Fr
Frequency reference
Nd1
Network controller1, digital section
Nd2
Network controller2, digital section (only 4-oort instruments)
Sy1/DDSCON
Synthesizer1
Sy1/DDSCON
Synthesizer2(only 3-port and 4-port instruments)
Rm1
Reflectometer port1
Rm2
Reflectometer port2
Rm3
Reflectometer port3 (applies only to 3-port and 4-port-instruments)
Rm4
Reflectometer port4 (applies only to 4-port instruments)
1145.1155.82
3.65
E-5
Troubleshooting
R&S ZVA
Total selftest status: user mode ---PASSED--Instrument Type: ZVA8 with 4 Ports
Part Number: 1145.1110k10
Product ID: 01.00
Serial Number: 100124
IP Addresses
IP Address: 0.0.0.0&nbs;
Subnet Mask: 0.0.0.0
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
IP Address: 127.0.0.1 (Localhost)
Subnet Mask: 255.0.0.0
SyMapping: ZVA8_P4
LO Divider: is not active
Date: 05/28/04
Time: 14:52:57
Voltages Fr
Test description
Min
Max
Result
State
+10V_A SUPPLY
1.550V
1.950V
1.756V
PASSED
+5V_A SUPPLY
1.400V
1.800V
1.560V
PASSED
+5V_REF
1.400V
1.800V
1.560V
PASSED
+12V_STB
1.900V
2.300V
2.112V
PASSED
128_VCXO
0.800V
4.000V
2.696V
PASSED
ADC_CLK
0.800V
4.000V
2.060V
PASSED
-10V_A SUPPLY
1.900V
2.300V
2.128V
PASSED
-5V_A SUPPLY
2.100V
2.500V
2.264V
PASSED
Test description
Min
Max
Result
State
+5VA_ADC
2.250V
2.750V
2.488V
PASSED
+2.5VD_MDD1
1.125V
1.375V
1.264V
PASSED
+2.5VD_MDD2
1.125V
1.375V
1.264V
PASSED
+1.5VD_FCON
0.675V
0.825V
0.752V
PASSED
-5VA_ADC
2.250V
2.750V
2.464V
PASSED
DGND1
0.000V
0.200V
0.000V
PASSED
DGND2
0.000V
0.200V
0.000V
PASSED
AGND
0.000V
0.200V
0.000V
PASSED
Voltages Nd1
1145.1155.82
3.66
E-5
R&S ZVA
Troubleshooting
Voltages Nd2
Test description
Min
Max
Result
State
+5VA_ADC
2.250V
2.750V
2.484V
PASSED
+2.5VD_MDD1
1.125V
1.375V
1.260V
PASSED
+2.5VD_MDD2
1.125V
1.375V
1.260V
PASSED
+1.5VD_FCON
0.675V
0.825V
0.752V
PASSED
-5VA_ADC
2.250V
2.750V
2.460V
PASSED
DGND1
0.000V
0.200V
0.000V
PASSED
DGND2
0.000V
0.200V
0.000V
PASSED
AGND
0.000V
0.200V
0.000V
PASSED
Test description
Min
Max
Result
State
+10V_A SUPPLY
1.500V
2.000V
1.752V
PASSED
+5V_A SUPPLY
1.300V
1.800V
1.560V
PASSED
+5V_REF
1.300V
1.800V
1.568V
PASSED
+7V_A SUPPLY
1.400V
1.900V
1.628V
PASSED
Test description
Min
Max
Result
State
+10V_A SUPPLY
1.500V
2.000V
1.752V
PASSED
+5V_A SUPPLY
1.300V
1.800V
1.560V
PASSED
+5V_REF
1.300V
1.800V
1.564V
PASSED
+7V_A SUPPLY
1.400V
1.900V
1.616V
PASSED
Voltages Sy1\DDSCON
Voltages Sy2\DDSCON
Voltages Rm1
Test description
Min
Max
Result
State
GND
0.000V
0.200V
0.000V
PASSED
GND
0.000V
0.200V
0.000V
PASSED
+5V SUPPLY
2.300V
2.700V
2.496V
PASSED
+10.5VA SUPPLY
2.300V
2.800V
2.564V
PASSED
+10.5VB SUPPLY
2.300V
2.800V
2.564V
PASSED
+12V FAN
2.000V
2.600V
2.216V
PASSED
+12V SUPPLY
2.000V
2.600V
2.204V
PASSED
-12V SUPPLY
1.600V
2.000V
1.796V
PASSED
Test description
Min
Max
Result
State
GND
0.000V
0.200V
0.000V
PASSED
GND
0.000V
0.200V
0.000V
PASSED
Voltages Rm2
1145.1155.82
3.67
E-5
Troubleshooting
R&S ZVA
+5V SUPPLY
2.300V
2.700V
2.500V
PASSED
+10.5VA SUPPLY
2.300V
2.800V
2.576V
PASSED
+10.5VB SUPPLY
2.300V
2.800V
2.592V
PASSED
+12V FAN
2.000V
2.600V
2.204V
PASSED
+12V SUPPLY
2.000V
2.600V
2.204V
PASSED
-12V SUPPLY
1.600V
2.000V
1.796V
PASSED
Test description
Min
Max
Result
State
GND
0.000V
0.200V
0.000V
PASSED
GND
0.000V
0.200V
0.000V
PASSED
+5V SUPPLY
2.300V
2.700V
2.500V
PASSED
+10.5VA SUPPLY
2.300V
2.800V
2.584V
PASSED
+10.5VB SUPPLY
2.300V
2.800V
2.600V
PASSED
+12V FAN
2.000V
2.600V
2.196V
PASSED
+12V SUPPLY
2.000V
2.600V
2.220V
PASSED
-12V SUPPLY
1.600V
2.000V
1.800V
PASSED
Test description
Min
Max
Result
State
GND
0.000V
0.200V
0.000V
PASSED
GND
0.000V
0.200V
0.000V
PASSED
+5V SUPPLY
2.300V
2.700V
2.492V
PASSED
+10.5VA SUPPLY
2.300V
2.800V
2.604V
PASSED
+10.5VB SUPPLY
2.300V
2.800V
2.568V
PASSED
+12V FAN
2.000V
2.600V
2.216V
PASSED
+12V SUPPLY
2.000V
2.600V
2.136V
PASSED
-12V SUPPLY
1.600V
2.000V
1.804V
PASSED
Voltages Rm3
Voltages Rm4
Voltages Fr
Voltages Nd1
Voltages Nd2
Voltages Sy1\DDSCON
Voltages Sy2\DDSCON
Voltages Rm1
Voltages Rm2
Voltages Rm3
Voltages Rm4
Home
1145.1155.82
3.68
E-5
R&S ZVA
Troubleshooting
Interpreting the Results of the Selftest
Negative voltages are transformed into positive voltages by means of a positive voltage and a resistor
network because the A/D converters that are used can handle only positive voltages. This is why an
acceptable negative voltage may elicit a FAIL because the associated positive voltage is out of
tolerance.
The voltages supplied by the power supply are not checked directly. The failure of a power supply
voltage can, however, be deduced from FAILs of certain voltages on several boards. The following
Table shows how the board-oriented voltages checked during the selftest are derived from the power
supply voltages.
Power
supply
+3.4 V
Fr
Nd
+5.2 V
+6.5 V
+8.25 V
+5V_A
+5V_REF
+2.5VD_MDD1
+2.5VD_MDD2
+1.5VD_FCON
+12.25 V
-6.5 V
-12.25 V
+10V_A
+12V_STB
-5V_A
-10V_A
+5VA_ADC
-5VA_ADC
Sy
+5V_A
+5V_REF
+7V_A
+10V_A
Rm
+5V
+10.5VA
+10.5VB
+12V
+12V FAN
-12V
If the voltages listed in a column are all FAIL, the corresponding power supply voltage has failed or is
out-of-tolerance. The power supply must then be replaced.
On the motherboard, there is a separate fuse for each board and for each of the power supply voltages
used on the board. If a FAIL message is output, the first action to take is to check the fuse. The LO
divider board must be removed before the fuses on the motherboard can be checked (See Chapter
Board Replacement).
If an internal board voltage is out-of-tolerance, even though the power supply voltages used on the
board are OK, the board must be replaced.
1145.1155.82
3.69
E-5
Troubleshooting
R&S ZVA
Checking the Temperature Sensors
Select Service Level 2 (see Service Functions).
Setup
Info
INFO
When the Hardware Info softkey is pressed
information about the installed hardware, the
results of temperature measurements and …
are displayed.
Hardware
Info
Selftest
Error
Log…
Del Error
Log
Temperature Info
Current Temperature Readings
Component
Sensor
Temperature
Sensor
Temperature
Sensor
Motherboard
Near NC:
33.75°C Near SY:
34.75°C Near PS:
Netcon 1
Analog:
40.25°C Digital:
49.75°C
Netcon 2
Analog:
----- Digital:
-----
Reflectometer 1
Generator:
38.50°C
Reflectometer 2
Generator:
36.00°C
Reflectometer 3
Generator:
38.25°C
Reflectometer 4
Generator:
39.25°C
Synthesizer 1
Synth. 1:
Synthesizer 2
Synth. 2:
Temperature
38.50°C
Highly elevated temperature values indicate a fan failure.
1145.1155.82
3.70
E-5
R&S ZVA
Troubleshooting
Service Functions
The service functions allow you to examine particular circuit sections on specific boards or to make
well-defined settings that would normally change automatically according to the state of the instrument
(e.g. the IF). There are a number of service functions which, if used incorrectly, could cause the
instrument to malfunction. Usually, these functions are disabled. They are enabled only after a code
number (PASSWORD) has been entered.
There are three different service levels:
Service level
Password
0
No password necessary
1
894129
2
30473035
MENU
Service Function
System
System Config…
Measurement Wizard [
Print
[
Enter Password:
\ Internal Reference
External Reference
Preset
GPIB Address…
Service Function…
External Tools
1145.1155.82
[
3.71
E-5
Troubleshooting
R&S ZVA
Service Function Structure
.
Group
Main ID
.
Sub ID
.
Function
Group
Applies to
1
API
2
HW (boards)
Boards
Boards
Main ID
Sub ID
0: All boards
0
1: Network controller1
0: All board
.
Address
.
Data
1: PCI
2: ND
3: NA
2: Network controller2
5: Motherboard
0:
9: Frequency reference
0:
11: Synthesizer1
0: All board
1: SY1
2: SY2
3: SY3
4: SY4
12: Synthesizer2
21: Reflectometer1
0: all board
1: GEN
2: REC
22: Reflectometer 2
23: Reflectometer 3
24: Reflectometer 4
1145.1155.82
3.72
E-5
R&S ZVA
Troubleshooting
Group 1:
General Functions
Functions
Service
function
Enables/disables the peak detector and RMS 1.0.0.1.X
detector independently of the model
Enable/disables the arbitrary mode settings in
the port configuration (e.g. LowNoise/
LowDistortion) independently of the model
1.0.0.5.X
Activates or deactivates the setting of measured 1.1.0.2.X
values to default values when status messages
are issued due to HW faults
Activates or deactivates factory calibration for 1.1.0.3.X
the active setup
Data
Serv. Lev.
0
Use disabled
2
1
Use enabled
0
Use disabled
1
Use enabled
0
Deactivate default values
1
Activate default values
0
Deactivate factory calibration
1
Activate factory calibration
2
0
0
Group 2:
General Functions
Functions
Service function
Suppress error-message box
2.0.0.0.X
Selftest all boards
2.0.0.5.0.0
Data
X=0
MSG box is output (default state)
X=1
MSG box is suppressed (error is
nevertheless entered in the log file)
Serv. Lev.
1
0, 1 or 2
Network controller
Functions
Service function
ND1:Read Temp (addr.:68)
2.1.2.3
1
ND2:Read Temp (addr.:68)
2.2.2.3
1
ND[1..2] Selftest
2.[1-2].2.5.0.0
0, 1 or 2
NA1:Read Temp (addr.:69)
2.1.3.3
1
NA2:Read Temp (addr.:69)
2.2.3.3
1
1145.1155.82
3.73
Data
Serv. lev.
E-5
Troubleshooting
R&S ZVA
Motherboard
Functions
Service function
Data
Serv. lev.
MB: Fan manual
2.5.0.11.1.X
X= 0 to 5
MB: Fan automatic
2.5.0.11.0
1
MB:Read Temp
2.5.0.3.1
1
2.5.0.3.2
1
2.5.0.3.3
1
1
Front (NC) (addr.:205)
MB: Read Temp
Rear (SY) (addr.: 204)
MB: Read Temp
Back (PS) (addr.: 202)
Frequency reference
Functions
Service function
FR Selftest
2.9.0.5.0.0
Data
Serv.lev.
0, 1 or 2
Reflectometers
Functions
Service function
Data
Serv.lev.
RM[1-4]: Fan manual
2.[21-24].0.11.X
X = 1 to 5
1
RM[1-4]:Fan automatic
2.[21-24].0.11.0
1
RM[1-4]: Read Temp Gen
2.[21-24].1.3
1
RM[1-4]: Read Temp Rec
2.[21-24].2.3
1
RM[1-4]: Selftest
2.[21-24].0.5.X
RM[1-4]: Read OVL
2.[21-24].0.12
1
RM[1-4]: OVL Reset
2.[21-24].0.13
1
RM[1-4] Generator Selftest
2.[21-24].1.5.0.0
0, 1 or 2
RM[1-4]: IF shift
2.[21-24].2.18.ZF
X = 0 to 4
IF in Hz
1
0
0 = IF via shift table
1145.1155.82
3.74
E-5
R&S ZVA
Troubleshooting
Determining which Boards are defective
The table below lists boards that are probably defective based on the faults that occurred during the
performance test.
Defective board
Problem with:
Probable
Also possible
Frequency accuracy
Frequency reference
SSB phase-noise
Only one port
All ports
Synthesizer1
Frequency reference
Level accuracy
Only one port
All ports
Reflectometer associated with defective port
Synthesizer1
Max. output level
Only one port
All ports
Reflectometer associated with defective port
Synthesizer1
Absolute accuracy wave quantity a
Reflectometer associated with defective port
Level linearity
Reflectometer associated with defective port
Harmonic ratio
Reflectometer associated with defective port
Spurious suppression
Synthesizer1
Matching portx
Bridge unit of reflectometer associated with the
defective port
Directivity portx
Bridge unit of reflectometer associated with the
defective port
Receiver absolute accuracy Port 1, 2
Port 3, 4
All ports
Reflectometer associated with defective port
Reflectometer associated with defective port
Synthesizer1
Network controller1
Network controller2
Frequency reference
Receiver linearity for high levels Portx
All ports
Reflectometer associated with defective port
LO divider
LO divider
Synthesizer2
Receiver linearity for low levels
Network controller1
Network controller2
Port1, 2
Port3, 4
Synthesizer1
Receiver noise level portx
Reflectometer associated with defective port
Synthesizer2 or
synth.1 for 2-port models
Dynamic range portx
Reflectometer associated with defective port
(see Circular 10028)
Synthesizer2 or.
synth.1 for 2-port models
DC measurement input1V
Motherboard
Network controller1
DC measurement input 10V
Motherboard
Network controller1
Frequency reference input/output
Frequency reference
Accuracy on S-parameter measurements
depending on meas. bandwidth
See Circular 10029
A board test should be performed before the board that has been deduced to be defective is replaced.
1145.1155.82
3.75
E-5
Troubleshooting
R&S ZVA
Board Test
When boards are being tested, internal sources are used whenever possible. This means that it is
always assumed that the downstream board in the signal path is OK. If a clear fault is not present, the
order of the board tests given below should always be followed.
The inputs and outputs of the boards to be tested can be accessed via cables in the lower section of the
instrument (except the frequency reference board).
Opening the instrument
(See Chapter 5, drawing1145.1110)
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the instrument base cover (297) after undoing the screws (299).
Only when testing the frequency reference board:
Lift off the instrument top cover (296) after undoing the screws (298).
1145.1155.82
3.76
E-5
R&S ZVA
Troubleshooting
Testing the frequency reference board
(see Test Equipment)
Remove the board from the instrument.
Reinsert board and extension card.
Connect the output to be tested to the spectrum analyzer using an adapter cable and
adapter SMA-N.
Set the frequencies listed in the table.
Check signals according to following table.
Signal
Connector
Frequency
Nom. level
NA1_AD_CLK
X103
80 MHz
10 dBm ±1dB
NA2_AD_CLK
X104
80 MHz
10 dBm ±1dB
SY1_REF
X105
128 MHz
10 dBm ±1dB
SY2_REF
X106
128 MHz
10 dBm ±1dB
REF_10_OUTIN
X107
10 MHz
6 dBm ±1dB
Setting
Menu/System/Internal
Reference
The board must be replaced if the signal is more than 2 dB below the stated nominal level.
Connect the frequency reference output of the spectrum analyzer to X107 (REF_10_OUTIN) using
an adapter cable and adapter SMA-N.
Connect X105 or X106 (SY1_REF or. SY2_REF) to the spectrum analyzer using an adapter cable
and adapter SMA-N.
The 128 MHz signal’s frequency must precisely equal its nominal frequency.
If the frequency differs in any way (e.g. 128.001 MHz), replace the board.
1145.1155.82
3.77
E-5
Troubleshooting
R&S ZVA
Testing the Synthesizer Board
N.B.:
Synthesizers with part numbers 1145.xxxx or 1300.xxxx are no longer available. In case of
defect please contact the Central Service in Munich.
Disconnect source (or local) cable at the reflectometer (1 to 4, depending on which synthesizer
section is to be tested).
Connect the end of the cable to the spectrum analyzer input via an adapter cable and adapter
SMA-N.
N.B.:
Bend the source cable as little as possible, if necessary secure adapter cable with
adhesive tape.
Enter service function 2.21.2.18.17512345 (IF = 17.512345 MHz).
[ Mode : Spurious Avoidance : LO > RF ]
Set the frequencies listed in the table on the ZVA and check the values.
[ Sweep : Sweep Type : CW Mode : CW Frequency : …Hz]
[ Sweep : Single : Restart]
Synthesizer-LS 1302.4025.xx
Source Mod. 02 and Mod. 20
Frequency
(ZVA setting)
Source Level
(Mod. 02)
2nd harmonic
3rd harmonic
300 kHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
100 MHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
1 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
2 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
3 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
4 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
6 GHz
+3 dBm to -7 dBm
< -27 dBc
< -30 dBc
8 GHz
+3 dBm to -7 dBm
< -27 dBc
< -30 dBc
Port setting
Source output
Isolation
Port1 inactive
X168
-90 dBc ±5 dB
Port2 active
X169
Port1 active
X168
Port2 inactive
X169
Isolation of source switch1 to 4
ZVA frequency 8 GHz
Port no.
1
2
1145.1155.82
3.78
-90 dBc ±5 dB
E-5
R&S ZVA
Troubleshooting
Local Mod. 02
Frequency
(ZVA setting)
LO-Frequency
(Spec analyzer
setting)
Local Level
(Mod. 02)
2nd
harmonic
3rd harmonic
300 kHz
17.812345 MHz
+2 dBm to -15 dBm
< -5 dBc
< +2 dBc
100 MHz
117.512345 MHz
+2 dBm to -15 dBm
< -5 dBc
< +2 dBc
1 GHz
1017.512345 MHz
+2 dBm to -4 dBm
< -5 dBc
< -5 dBc
2 GHz
2017.512345 MHz
+2 dBm to -4 dBm
< -5 dBc
< -5 dBc
3 GHz
3017.512345 MHz
+2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
3.8 GHz
3817.512345 MHz
+2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
4 GHz
4017.512345 MHz
+2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
5.2 GHz
5217.512345 MHz
+2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
5.3 GHz
5317.512345 MHz
+2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
7.2 GHz
7217.512345 MHz
+2 dBm to -5 dBm
< -5 dBc
< -5 dBc
8 GHz
8017.512345 MHz
+2 dBm to -5 dBm
< -5 dBc
< -5 dBc
Frequency
(ZVA setting)
LO-Frequency
(Spec analyzer
setting)
Local Level
(Mod. 24)
2nd
harmonic
3rd harmonic
10 MHz
27.512345 MHz
-3 dBm to -20 dBm
< -5 dBc
< +2 dBc
100 MHz
117.512345 MHz
-3 dBm to -20 dBm
< -5 dBc
< +2 dBc
1 GHz
1017.512345 MHz
-3 dBm to -9 dBm
< -5 dBc
< -5 dBc
2 GHz
2017.512345 MHz
-3 dBm to -9 dBm
< -5 dBc
< -5 dBc
3 GHz
3017.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
3.8 GHz
3817.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
4 GHz
4017.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
5.2 GHz
5217.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
5.3 GHz
5317.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
7.2 GHz
7217.512345 MHz
-3 dBm to -10 dBm
< -5 dBc
< -5 dBc
8 GHz
8017.512345 MHz
-3 dBm to -10 dBm
< -5 dBc
< -5 dBc
Local Mod. 20
1145.1155.82
3.79
E-5
Troubleshooting
R&S ZVA
Synthesizer-DS 1302.5180.xx
Source 1 to 4 (set port1 to 4 active)
Frequency
(ZVA setting)
Source Level
2nd harmonic
3rd harmonic
300 kHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
100 MHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
1 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
2 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
3 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
4 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
6 GHz
+3 dBm to -7 dBm
< -27 dBc
< -30 dBc
8 GHz
+3 dBm to -7 dBm
< -27 dBc
< -30 dBc
Port setting
Source output
Isolation
Port1 inactive
X165
-90 dBc ±5 dB
Port2 active
X166
Port1 active
X165
Port2 inactive
X166
-90 dBc ±5 dB
Port3 inactive
X168
-90 dBc ±5 dB
Port4 active
X169
Port3 active
X168
Port4 inactive
X169
Isolation of source switch1 to 4
ZVA frequency 8 GHz
Port no.
1
2
3
4
-90 dBc ±5 dB
The cable loss must also be taken into account at the stated levels. For the specified cable it is
0.25 dB/GHz (0.5 m) 0.5 dB/GHz (1 m).
The board must be replaced if the level is more than 2 dB below the specified value or the other values
are more than 2 dB above their specified value.
1145.1155.82
3.80
E-5
R&S ZVA
Troubleshooting
Synthesizer-LO 1302.4248.02
Local 1 to 4 (set port1 to 4 active)
Frequency
(ZVA setting)
LO-Frequency
(Spec analyzer
setting)
Local Level
2nd
harmonic
3rd
harmonic
300 kHz
17.812345 MHz
2 dBm to -15 dBm
< -5 dBc
< 2 dBc
100 MHz
117.512345 MHz
2 dBm to -15 dBm
< -5 dBc
< 2 dBc
1 GHz
1017.512345 MHz
2 dBm to -4 dBm
< -5 dBc
< -5 dBc
2 GHz
2017.512345 MHz
2 dBm to -4 dBm
< -5 dBc
< -5 dBc
3 GHz
3017.512345 MHz
2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
3.8 GHz
3817.512345 MHz
2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
4 GHz
4017.512345 MHz
2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
5.2 GHz
5217.512345 MHz
2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
5.5 GHz
5517.512345 MHz
2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
7.2 GHz
7217.512345 MHz
3 dBm to -4 dBm
< -5 dBc
---
8 GHz
8017.512345 MHz
3 dBm to -4 dBm
< -5 dBc
---
Synthesizer-LO 1302.4248.20
Local 1 to 4 (set port1 to 4 active)
1145.1155.82
Frequency
(ZVA setting)
LO-Frequency
(Spec analyzer
setting)
Local Level
2nd
harmonic
3rd
harmonic
300 kHz
17.812345 MHz
-3 dBm to -20 dBm
< -5 dBc
< 2 dBc
100 MHz
117.512345 MHz
-3 dBm to -20 dBm
< -5 dBc
< 2 dBc
1 GHz
1017.512345 MHz
-3 dBm to -9 dBm
< -5 dBc
< -5 dBc
2 GHz
2017.512345 MHz
-3 dBm to -9 dBm
< -5 dBc
< -5 dBc
3 GHz
3017.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
3.8 GHz
3817.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
4 GHz
4017.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
5.2 GHz
5217.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
5.5 GHz
5517.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
7.2 GHz
7217.512345 MHz
-3 dBm to -10 dBm
< -5 dBc
---
8 GHz
8017.512345 MHz
-3 dBm to -10 dBm
< -5 dBc
---
3.81
E-5
Troubleshooting
R&S ZVA
Synthesizer-12
Source signals
Local signals
1145.1155.82
(W168, W169) with synth. 1305.3002.02 and synth. 1305.3002.04
(W165, W166, W168, W169) with synth. 1305.7220.02
Frequency
(ZVA setting)
Source Level
(Mod. 02)
2nd harmonic
10 MHz
+10 dBm to -10 dBm
-----
100 MHz
+10 dBm to -10 dBm
-----
300 MHz
+10 dBm to -10 dBm
< -25 dBc
1 GHz
+10 dBm to -10 dBm
-----
2 GHz
+10 dBm to -10 dBm
-----
2.5 GHz
+10 dBm to -10 dBm
< -25 dBc
3 GHz
+10 dBm to -10 dBm
-----
4 GHz
+10 dBm to -10 dBm
-----
6 GHz
+10 dBm to -10 dBm
-----
8 GHz
+10 dBm to -10 dBm
-----
10 GHz
+10 dBm to -10 dBm
-----
12 GHz
+10 dBm to -10 dBm
-----
(W165, W166) with synth. 1305.3002.02 and synth. 1305.3002.03
(W155, W156, W158, W159) with synth. 1305.7220.02
Frequency
(ZVA setting)
LO-Frequency
(Spec analyzer
setting)
Source Level
(Mod. 02)
30 MHz
47.512345 MHz
+10 dBm to -10 dBm
100 MHz
117.512345 MHz
+10 dBm to -10 dBm
1 GHz
1.017512345 GHz
+10 dBm to -10 dBm
2 GHz
2.017512345 GHz
+10 dBm to -10 dBm
3 GHz
3.017512345 GHz
+10 dBm to -10 dBm
4 GHz
4.017512345 GHz
+10 dBm to -10 dBm
6 GHz
6.017512345 GHz
+10 dBm to -10 dBm
8 GHz
8.017512345 GHz
+10 dBm to -10 dBm
10 GHz
10.017512345 GHz
+10 dBm to -10 dBm
12 GHz
12.017512345 GHz
+10 dBm to -10 dBm
3.82
E-5
R&S ZVA
Troubleshooting
Testing the Reflectometer RM8
Generator levels
It is assumed that the synthesizer section (synthesizer1) associated with the reflectometer to be tested
is OK.
Loosen cable W514 (GEN -> Bridge unit) at both ends and screw off at the generator output GEN.
Note: When loosening, support the cable with a 7mm spanner
Connect the generator output to the spectrum analyzer using the SMA cables () and adapter SMAN.
Set the power to 8 dBm
Set the ZVA to the CW sweep mode.
Set the frequencies listed in the table.
Frequency
Level
2nd harmonic
3rd harmonic
300 kHz
16 dBm
---
---
50 MHz
16 dBm
< - 21 dBc
< - 21 dBc
1 GHz
16 dBm
< - 21 dBc
< - 21 dBc
3 GHz
16 dBm
< - 21 dBc
< - 21 dBc
6 GHz
16 dBm
< - 21 dBc
---
8 GHz
16 dBm
< - 21 dBc
---
With the stated levels, the cable loss must still be taken into account. For the specified cable it is
0.25 dB/GHz.
Receiver levels
The following is assumed:
• The LO synthesizer section (synthesizer1 mod. 04, synthesizer2) associated with the reflectometer
to be tested is OK.
• The network controller associated with the reflectometer to be tested is OK.
• One reflectometer in the instrument is functioning.
Loosen cable W515 (Bridge unit -> MEAS) and cable W518 (Bridge unit -> REF) at both ends and
screw off at the MEAS and REF receiver inputs.
N.B.: When loosening, support the cable with a 7mm spanner
Connect the receiver input (MEAS or REF) to a functioning instrument port using an adapter cable
and adapter SMA-N.
Set the ZVA to the CW sweep mode.
Set the frequencies and output levels for the port used for the measurement as indicated in the
table and read off the level for the receiver to be tested (wave quantity ax or bx).
1145.1155.82
3.83
E-5
Troubleshooting
R&S ZVA
Frequency
Output level
Displayed level
ax or bx
300 kHz
-20 dBm
0 dBm
50 MHz
-20 dBm
0 dBm
1 GHz
-20 dBm
0 dBm
3 GHz
-20 dBm
0 dBm
6 GHz
-20 dBm
0 dBm
8 GHz
-20 dBm
0 dBm
With the stated levels, the cable loss must still be taken into account. For the specified cable, it is
0.25 dB/GHz (0.5 m) or. 0.5 dB/GHz (1 m).
If the measured values are more than 3 dB below the levels and ratios list in the table, the board must
be replaced.
Bridge unit levels
The following is assumed:
• One reflectometer in the instrument is OK.
Method 1:
The generator section of the associated reflectometer is OK (output level at the port
specifications).
meets
Loosen cable W515 (Bridge unit -> MEAS) and cable W518 (Bridge unit -> REF) at both ends and
disconnect at the bridge unit.
N.B.: When loosening, support the cable with a 7mm spanner
Connect the bridge unit output (MEAS = connector W515 or REF = connector W518) to a
functioning port using the SMA cable and adapter SMA-N (measure wave quantity bx). Terminate
the bridge unit output that is not used with an SMA termination.
Screw the SHORT from a N-calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + (linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Set the frequencies and levels listed in the table for the reflectometer associated with the bridge
unit (port) and measure the level (wave quantity bx) at the port used for the measurement.
1145.1155.82
3.84
E-5
R&S ZVA
Troubleshooting
Frequency
Level
Output level MEAS
Output level REF
300 kHz
0 dBm
-18 dBm
-32 dBm
50 MHz
0 dBm
-18 dBm
-32 dBm
1 GHz
0 dBm
-18 dBm
-32 dBm
3 GHz
0 dBm
-18 dBm
-32 dBm
6 GHz
0 dBm
-18 dBm
-32 dBm
8 GHz
0 dBm
-18 dBm
-32 dBm
With the stated levels, the cable loss must still be taken into account. For the specified cable it is
0.25 dB/GHz.
If the measured values are more than 3 dB below the levels in the table, the board must be replaced.
Method 2:
The receive section of the associated reflectometer is OK.
Loosen cable W514 (GEN -> Bridge unit) at both ends and screw off at the bridge unit.
N.B.: When loosening, support the cable with a 7mm spanner
Connect the bridge input (connector W514) to a functioning port using the SMA cable and SMA-N
adapter.
Screw the SHORT from a N-calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + (linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Set the frequencies and levels listed in the table at the port used for the measurement and measure
the level (wave quantity ax or bx) at the reflectometer associated with the bridge unit (port).
Frequency
Level
Level ax and bx
300 kHz
8 dBm
0 dBm
50 MHz
8 dBm
0 dBm
1 GHz
8 dBm
0 dBm
3 GHz
8 dBm
0 dBm
6 GHz
8 dBm
0 dBm
8 GHz
8 dBm
0 dBm
With the stated levels, the cable loss must still be taken into account. For the specified cable it is
0.25 dB/GHz.
If the measured values are more than 3 dB below the levels given in the table, the board must be
replaced.
1145.1155.82
3.85
E-5
Troubleshooting
R&S ZVA
Bridge Directivity
The following is assumed:
• The generator and receiver sections of the reflectometer associated with the bridge unit are OK.
Perform a sweep from 300 kHz to 8 GHz, measure Ratio bx/ax Source Portx
Screw the SHORT from a N-calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector, save measured values (More Mem :
Data -> Mem3).
Screw the MATCH from the calibration kit to the port connector.
Select User Def Math : linMag(Data) / ((linMag(Mem2) + linMag(Mem3)) / 2 : Math = User Def
The trace gives the directivity.
Frequency range
Directivity
300 kHz to 50 MHz
< -10 dB
50 MHz to 8 GHz
< -16 dB
If the measured values are greater than the values stated in the table, the bridge unit must be replaced.
Bridge unit: Port Matching
It is assumed that there is a functioning reflectometer in the instrument.
Loosen cables W514 (GEN -> Bridge unit), W515 (Bridge unit -> MEAS) and W518 (Bridge unit ->
REF) at both ends and unscrew at the bridge unit.
N.B.: When loosening, support the cable with a 7mm spanner
Terminate the bridge unit input and bridge unit outputs with 3 SMA terminations.
Connect N test cable to a functioning instrument port and perform a 1-port calibration at the end of
the cable.
Connect the end of the test cable to the port of the bridge unit under test and display the Sxx
magnitude on the screen.
Frequency range
Sxx dB
300 kHz to 8 GHz
-18 dB
If the values in the table are exceeded, the board must be replaced.
1145.1155.82
3.86
E-5
R&S ZVA
Troubleshooting
Testing the Reflectometer RM24
Generator levels
It is assumed that the synthesizer section (synthesizer1) associated with the reflectometer to be tested
is OK.
Loosen cable W514 (GEN -> coupler unit) at both ends and screw off at the generator output GEN.
Connect the generator output to the spectrum analyzer using the SMA cable ().
Set the ZVA to the CW sweep mode.
Set the frequencies listed in the table.
Set the power listed in the table.
Frequency
Set power to
Level on GEN output
2nd harmonic
3rd harmonic
10 MHz
10 dBm
13.0 dBm
---
---
100 MHz
10 dBm
13.0 dBm
< - 21 dBc
< - 21 dBc
1 GHz
10 dBm
13.2 dBm
< - 21 dBc
< - 21 dBc
4 GHz
10 dBm
13.7 dBm
< - 21 dBc
< - 21 dBc
8 GHz
10 dBm
14.3 dBm
< - 21 dBc
< - 21 dBc
9 GHz
10 dBm
14.5 dBm
< - 21 dBc
---
15.0 dBm
---
---
7.5 dBm
---
---
8.0 dBm
---
---
8.3 dBm
---
---
12 GHz
15 GHz
18 GHz
20 GHz
10 dBm
5 dBm
5 dBm
5 dBm
With the stated levels, the cable loss must still be taken into account. For the specified cable it is
0.25 dB/GHz.
Receiver levels
The following is assumed:
• The LO synthesizer section (synthesizer1 mod. 20, synthesizer2) associated with the reflectometer
to be tested is OK.
• The network controller associated with the reflectometer to be tested is OK.
• One reflectometer in the instrument is functioning.
Loosen cable W515 (coupler unit -> MEAS) and cable W518 (coupler unit -> REF) at both ends
and screw off at the MEAS and REF receiver inputs.
Connect the receiver input (MEAS or REF) to a functioning instrument port using an adapter cable.
Set the ZVA to the CW sweep mode.
Set the frequencies and output levels for the port used for the measurement as indicated in the
table and read off the level for the receiver to be tested (wave quantity ax or bx).
1145.1155.82
3.87
E-5
Troubleshooting
R&S ZVA
Frequency
Output level
Displayed level
ax or bx
10 MHz
-30 dBm
+20 dBm ± 3 dB
100 MHz
-30 dBm
+5 dBm ± 3 dB
1 GHz
-20 dBm
-5 dBm ± 3 dB
2.5 GHz
-20 dBm
-10 dBm ± 3 dB
3 GHz
-20 dBm
-10 dBm ± 3 dB
8 GHz
-20 dBm
-10 dBm ± 3 dB
9 GHz
-20 dBm
-10 dBm ± 3 dB
12 GHz
-20 dBm
-10 dBm ± 3 dB
15 GHz
-20 dBm
-8 dBm ± 4 dB
18 GHz
-20 dBm
-8 dBm ± 4 dB
20 GHz
-20 dBm
-8 dBm ± 4 dB
With the stated levels, the cable loss must still be taken into account. For the specified cable, it is
0.25 dB/GHz (0.5 m) or. 0.5 dB/GHz (1 m).
If the measured values are more than 2 dB below the levels list in the table, the board must be
replaced.
Coupler unit levels
The following is assumed:
• One reflectometer in the instrument is OK.
Method 1:
The generator section of the associated reflectometer is OK (output level at the port meets
specifications).
Loosen cable W515 (coupler unit -> MEAS) and cable W518 (coupler unit -> REF) at both ends and
disconnect at the coupler unit.
Connect the coupler unit output (MEAS = connector W515 or REF = connector W518) to a
functioning port using the SMA cable. Terminate the coupler unit output that is not used with an
SMA termination.
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + (linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Set the frequencies and levels listed in the table for the reflectometer associated with the coupler
unit (port) and measure the level (wave quantity bx) at the port used for the measurement.
1145.1155.82
3.88
E-5
R&S ZVA
Troubleshooting
Frequency
Level
Output level MEAS
Output level REF
10 MHz
0 dBm
-50 dBm ± 3 dB
-47 dBm ± 3 dB
100 MHz
0 dBm
-35 dBm ± 3 dB
-32 dBm ± 3 dB
1 GHz
0 dBm
-15 dBm ± 3 dB
-11 dBm ± 3 dB
2 GHz
0 dBm
-10 dBm ± 3 dB
-4.7 dBm ± 3 dB
8 GHz
0 dBm
-10 dBm ± 3 dB
-3.7 dBm ± 3 dB
12 GHz
0 dBm
-10 dBm ± 3 dB
-3 dBm ± 3 dB
16 GHz
0 dBm
-12 dBm ± 4 dB
-2.3 dBm ± 4 dB
20 GHz
0 dBm
-12 dBm ± 4 dB
-1.7 dBm ± 4 dB
24 GHz
0 dBm
-12 dBm ± 4 dB
-1 dBm ± 4 dB
With the stated levels, the cable loss must still be taken into account. For the specified cable it is
0.25 dB/GHz.
If the measured values are more than 2 dB below the levels in the table, the coupler unit must be
replaced.
Method 2:
The receiver section of the associated reflectometer is OK.
Loosen cable W514 (GEN -> coupler unit) at both ends and screw off at the coupler unit.
Connect the coupler input (connector. W514) to a functioning port using the SMA cable.
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + (linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Set the frequencies and levels listed in the table at the port used for the measurement and measure
the level (wave quantity ax or bx) at the reflectometer associated with the coupler unit (port).
Frequency
Level
Level ax and bx
10 MHz
0 dBm
-3 dBm ± 1 dB
100 MHz
0 dBm
-3 dBm ± 1 dB
1 GHz
0 dBm
-3.2 dBm ± 1 dB
2 GHz
0 dBm
-3.3 dBm ± 1 dB
8 GHz
0 dBm
-4.3 dBm ± 1 dB
12 GHz
0 dBm
-5 dBm ± 1 dB
16 GHz
0 dBm
-5.7 dBm ± 1 dB
20 GHz
0 dBm
-6.3 dBm ± 1 dB
24 GHz
0 dBm
-7 dBm ± 1 dB
With the stated levels, the cable loss must still be taken into account. For the specified cable it is
0.25 dB/GHz.
If the measured values are more than 2 dB below the levels given in the table, the coupler unit must be
replaced.
1145.1155.82
3.89
E-5
Troubleshooting
R&S ZVA
Coupler Directivity
The following is assumed:
• The generator and receiver sections of the reflectometer associated with the coupler unit are OK.
Perform a sweep from 10 MHz to 24 GHz, measure Ratio bx/ax Source Portx
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector, save measured values (More Mem :
Data -> Mem3).
Screw the MATCH from the calibration kit to the port connector.
Select User Def Math : linMag(Data) / ((linMag(Mem2) + linMag(Mem3)) / 2 : Math = User Def
The trace gives the directivity.
Frequency range
Directivity
10 MHz to 12 GHz
< -15 dB
12 GHz to 24 GHz
< -10 dB
If the measured values are greater than the values stated in the table, the coupler unit must be
replaced.
Coupler unit: Port Matching
It is assumed that there is a functioning reflectometer in the instrument.
Loosen cables W514 (GEN -> coupler unit), W515 (coupler unit -> MEAS) and W518 (coupler unit > REF) at both ends and unscrew at the coupler unit.
Terminate the coupler unit input and coupler unit outputs with 3 SMA terminations.
Connect test cable to a functioning instrument port and perform a 1-port calibration at the end of the
cable.
Connect the end of the test cable to the port of the coupler unit under test and display the Sxx
magnitude on the screen.
Frequency range
Sxx dB
10 MHz to 12 GHz
< -14 dB
12 GHz to 20 GHz
< -10 dB
If the values in the table are exceeded, the coupler must be replaced.
1145.1155.82
3.90
E-5
R&S ZVA
Troubleshooting
Testing the Reflectometer RM44 and RM50
Generator levels
It is assumed that the synthesizer section (synthesizer1) associated with the reflectometer to be tested
is OK.
Loosen cable W514A (GEN -> coupler unit) or W512 (GEN -> attenuator) at both ends and screw
off at the generator output GEN.
Connect the generator output to the spectrum analyzer using the K-cable (ZVA40) or V-cable
(ZVA50).
Set the ZVA to the CW sweep mode.
Set the frequencies listed in the table.
Set the power listed in the table.
Frequency
Set power to
(without
GenAtt)
Set power to
(with GenAtt)
Level on GEN
output
2nd harmonic
3rd harmonic
10 MHz
10 dBm
9 dBm
12.0 dBm
---
---
50 MHz
10 dBm
9 dBm
12.0 dBm
< - 21 dBc
< - 21 dBc
1 GHz
10 dBm
9 dBm
12.0 dBm
< - 21 dBc
< - 21 dBc
4 GHz
10 dBm
9 dBm
12.0 dBm
< - 21 dBc
< - 21 dBc
8 GHz
10 dBm
9 dBm
12.0 dBm
< - 21 dBc
< - 21 dBc
10 GHz
10 dBm
9 dBm
14.0 dBm
< - 21 dBc
< - 21 dBc
13 GHz
10 dBm
9 dBm
14.0 dBm
< - 21 dBc
< - 21 dBc
15 GHz
10 dBm
8 dBm
14.0 dBm
< - 21 dBc
< - 21 dBc
18 GHz
10 dBm
8 dBm
14.0 dBm
< - 21 dBc
< - 21 dBc
20 GHz
10 dBm
8 dBm
14.0 dBm
< - 21 dBc
---
24 GHz
10 dBm
8 dBm
14.5 dBm
< - 21 dBc
---
28 GHz
10 dBm
7 dBm
14.5 dBm
< - 21 dBc
---
32 GHz
10 dBm
7 dBm
14.5 dBm
---
---
36 GHz
6 dBm
3 dBm
10.5 dBm
---
---
40 GHz
6 dBm
3 dBm
10.5 dBm
---
---
45 GHz (ZVA50 only)
6 dBm
3 dBm
10.5 dBm
---
---
50 GHz (ZVA50 only)
6 dBm
3 dBm
10.5 dBm
---
---
With the stated levels, the cable loss must still be taken into account.
1145.1155.82
3.91
E-5
Troubleshooting
R&S ZVA
Receiver levels
The following is assumed:
• The LO synthesizer section (synthesizer1 mod. 20, synthesizer2) associated with the reflectometer
to be tested is OK.
• The network controller associated with the reflectometer to be tested is OK.
• One reflectometer in the instrument is functioning.
Loosen the cable to the receiver input MEAS (X6) and the cable to the receiver input REF (X5) at
both ends and screw off at the receiver inputs.
Connect the receiver input (MEAS or REF) to a functioning instrument port using the K-cable
(ZVA40) or V-cable (ZVA50).
Set the ZVA to the CW sweep mode.
Set the frequencies and output levels (check with power meter) for the port used for the
measurement as indicated in the table and read off the level for the receiver to be tested (wave
quantity ax or bx).
Frequency
Output level
Displayed level
ax
Displayed level
bx
10 MHz
-40 dBm
+15 dBm ± 4 dB
+7 dBm ± 4 dB
100 MHz
-40 dBm
-5 dBm ± 4 dB
-13 dBm ± 4 dB
1 GHz
-20 dBm
-2 dBm ± 4 dB
-10 dBm ± 4 dB
3 GHz
-20 dBm
-1 dBm ± 4 dB
-9 dBm ± 3 dB
8 GHz
-20 dBm
-1 dBm ± 4 dB
-9 dBm ± 3 dB
10 GHz
-20 dBm
-1 dBm ± 4 dB
-9 dBm ± 3 dB
12 GHz
-20 dBm
-0 dBm ± 4 dB
-9 dBm ± 3 dB
15 GHz
-20 dBm
-0 dBm ± 4 dB
-9 dBm ± 3 dB
18 GHz
-20 dBm
-0 dBm ± 4 dB
-9 dBm ± 3 dB
20 GHz
-20 dBm
-0 dBm ± 4 dB
-9 dBm ± 3 dB
25 GHz
-20 dBm
-0 dBm ± 4 dB
-8 dBm ± 3 dB
30 GHz
-20 dBm
-0 dBm ± 4 dB
-8 dBm ± 3 dB
35 GHz
-20 dBm
-0.5 dBm ± 4 dB
-7 dBm ± 4 dB
40 GHz
-20 dBm
-0.5 dBm ± 4 dB
-7 dBm ± 4 dB
45 GHz (ZVA50 only)
-20 dBm
-0.5 dBm ± 4 dB
-7 dBm ± 4 dB
50 GHz (ZVA50 only)
-20 dBm
-0.5 dBm ± 4 dB
-7 dBm ± 4 dB
With the stated levels, the cable loss must still be taken into account.
If the measured values are more than 2 dB below the levels list in the table, the board must be
replaced.
1145.1155.82
3.92
E-5
R&S ZVA
Troubleshooting
Coupler levels
The following is assumed:
• One reflectometer in the instrument is OK.
Method 1:
The generator section of the associated reflectometer is OK (output level at the port meets
specifications).
Loosen cable at coupler MEAS_OUT and at coupler REF_OUT at both ends and disconnect at the
coupler.
Connect the coupler output (MEAS = connector X3 or REF = connector X4) to a functioning port
using the K cable . Terminate the coupler output that is not used with an K-termination (Vtermination).
Set the frequencies and levels listed in the table for the reflectometer associated with the coupler
(port) and measure the level (wave quantity bx) at the port used for the measurement as follows:
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + (linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Frequency
Level
Output level MEAS
Output level REF
10 MHz
0 dBm
-47 dBm ± 4 dB
-55 dBm ± 4 dB
100 MHz
0 dBm
-27 dBm ± 4 dB
-35 dBm ± 4 dB
1 GHz
0 dBm
-10 dBm ± 4 dB
-18 dBm ± 4 dB
3 GHz
0 dBm
-11 dBm ± 3 dB
-19 dBm ± 4 dB
8 GHz
0 dBm
-11 dBm ± 3 dB
-19 dBm ± 4 dB
10 GHz
0 dBm
-11 dBm ± 3 dB
-19 dBm ± 4 dB
12 GHz
0 dBm
-11 dBm ± 3 dB
-20 dBm ± 4 dB
15 GHz
0 dBm
-11 dBm ± 3 dB
-20 dBm ± 4 dB
18 GHz
0 dBm
-11 dBm ± 3 dB
-20 dBm ± 4 dB
20 GHz
0 dBm
-11 dBm ± 3 dB
-20 dBm ± 4 dB
25 GHz
0 dBm
-12 dBm ± 3 dB
-20 dBm ± 4 dB
30 GHz
0 dBm
-12 dBm ± 3 dB
-20 dBm ± 4 dB
35 GHz
0 dBm
-13 dBm ± 4 dB
-19.5 dBm ± 4 dB
40 GHz
0 dBm
-13 dBm ± 4 dB
-19.5 dBm ± 4 dB
45 GHz
0 dBm
-13 dBm ± 4 dB
-19.5 dBm ± 4 dB
50 GHz
0 dBm
-13 dBm ± 4 dB
-19.5 dBm ± 4 dB
With the stated levels, the cable loss must still be taken into account.
If the measured values are more than 2 dB below the levels in the table, the coupler must be replaced.
1145.1155.82
3.93
E-5
Troubleshooting
R&S ZVA
Method 2:
The receiver section of the associated reflectometer is OK.
Loosen the cable at coupler GEN_IN at both ends and screw off at the coupler.
Connect the coupler (connector X1) to a functioning port using the K-cable (ZVA40) or V-cable
(ZVA50).
Set the frequencies and levels listed in the table at the port used for the measurement and measure
the level (wave quantity ax or bx) at the reflectometer associated with the coupler (port) as follows:
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + (linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Frequency
Level
level ax and bx (ZVA40)
level ax and bx (ZVA50)
10 MHz
0 dBm
> -2 dBm
> -2 dBm
100 MHz
0 dBm
> -2 dBm
> -2 dBm
1 GHz
0 dBm
> -2 dBm
> -2 dBm
3 GHz
0 dBm
> -2 dBm
> -2 dBm
8 GHz
0 dBm
> -2 dBm
> -2 dBm
10 GHz
0 dBm
> -2 dBm
> -2 dBm
12 GHz
0 dBm
> -2 dBm
> -2.5 dBm
15 GHz
0 dBm
> -2 dBm
> -2.5 dBm
18 GHz
0 dBm
> -2 dBm
> -2.5 dBm
20 GHz
0 dBm
> -2 dBm
> -2.5 dBm
25 GHz
0 dBm
> -2.5 dBm
> -3 dBm
30 GHz
0 dBm
> -2.5 dBm
> -3 dBm
35 GHz
0 dBm
> -3 dBm
> -3 dBm
40 GHz
0 dBm
> -3 dBm
> -3 dBm
45 GHz
0 dBm
--------
> -3.5 dBm
50 GHz
0 dBm
--------
> -3.5 dBm
With the stated levels, the cable loss must still be taken into account.
If the measured values are more than 2 dB below the levels given in the table, the coupler unit must be
replaced.
1145.1155.82
3.94
E-5
R&S ZVA
Troubleshooting
Coupler Directivity
The following is assumed:
• The generator and receiver sections of the reflectometer associated with the coupler are OK.
Perform a sweep from 10 MHz to 40 GHz, measure Ratio bx/ax Source Portx
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector, save measured values (More Mem :
Data -> Mem3).
Screw the MATCH from the calibration kit to the port connector.
Select User Def Math : linMag(Data) / ((linMag(Mem2) + linMag(Mem3)) / 2 : Math = User Def
The trace gives the directivity.
Frequency range
Directivity
10 MHz to 20 GHz
< -14 dB
20 GHz to 35 GHz
< -10 dB
35 GHz to 40 GHz
< -9 dB
ZVA50 only
35 GHz to 40 GHz
< -8 dB
ZVA50 only
40 GHz to 50 GHz
< -6 dB
If the measured values are more than 2 dB greater than the values stated in the table, the coupler must
be replaced.
Coupler Port Matching
It is assumed that there is a functioning reflectometer in the instrument.
Loosen cables W514A (GEN -> coupler), W515A (coupler -> MEAS) and W518A (coupler -> REF)
at both ends and unscrew at the coupler.
Terminate the coupler input and coupler outputs with three K-terminations (three V-terminations).
Connect test cable to a functioning instrument port and perform a 1-port calibration at the end of the
cable.
Connect the end of the test cable to the port of the coupler under test and display the Sxx
magnitude on the screen.
ZVA50 only
Frequency range
Sxx dB
10 MHz to 5GHz
< -20 dB
5 GHz to 20 GHz
< -15 dB
20 GHz to 30 GHz
< -12 dB
30 GHz to 40 GHz
< -11 dB
40 GHz to 50 GHz
< -10 dB
If the measured values are more than 2 dB greater than the values stated in the table, the coupler must
be replaced.
1145.1155.82
3.95
E-5
Troubleshooting
R&S ZVA
Testing the Reflectometer RM67
Generator levels
It is assumed that the synthesizer section (synthesizer1) associated with the reflectometer to be tested
is OK.
Loosen cable W514A (GEN -> BIAS 67) or W512A (GEN -> attenuator) at both ends and screw off
at the generator output GEN.
Connect the generator output to the spectrum analyzer using the V-cable (if FSU50 or FSU67 is not
available use a power meter for level measurements).
Set the ZVA to the CW sweep mode.
Set the frequencies listed in the table.
Set the power listed in the table.
Frequency
Set power to
(without GenAtt)
Set power to
(with GenAtt)
Level on GEN output
2nd harmonic
10 MHz
10 dBm
9 dBm
13.0 dBm
< - 30 dBm
500 MHz
13 dBm
12 dBm
16.0 dBm
< - 30 dBc
4 GHz
13 dBm
12 dBm
16.4 dBm
< - 30 dBc
8 GHz
13 dBm
12 dBm
16.7 dBm
< - 30 dBc
12 GHz
13 dBm
12 dBm
17.1 dBm
< - 25 dBc
16 GHz
13 dBm
11 dBm
17.4 dBm
< - 25 dBc
20 GHz
13 dBm
11 dBm
17.8 dBm
< - 25 dBc
24 GHz
10 dBm
6 dBm
15.2 dBm
---
28 GHz
10 dBm
7 dBm
15.5 dBm
---
32 GHz
10 dBm
7 dBm
15.9 dBm
---
36 GHz
6 dBm
3 dBm
12.3 dBm
---
40 GHz
6 dBm
3 dBm
12.6 dBm
---
45 GHz
6 dBm
3 dBm
13.1 dBm
---
50 GHz
6 dBm
3 dBm
13.5 dBm
---
55 GHz
2 dBm
- 1 dBm
10.0 dBm
---
60 GHz
2 dBm
- 1 dBm
10.4 dBm
---
67 GHz
2 dBm
- 1 dBm
11.1 dBm
---
With the stated levels, the cable loss must still be taken into account.
1145.1155.82
3.96
E-5
R&S ZVA
Troubleshooting
Receiver levels
The following is assumed:
• The LO synthesizer section associated with the reflectometer to be tested is OK.
• The network controller associated with the reflectometer to be tested is OK.
• One reflectometer in the instrument is functioning.
Loosen the cable to the receiver input MEAS (X6) and the cable to the receiver input REF (X5) at
both ends and screw off at the receiver inputs.
Connect the receiver input (MEAS or REF) to a functioning instrument port using the V-cable.
Set the ZVA to the CW sweep mode.
Set the frequencies and output levels (check with power meter) for the port used for the
measurement as indicated in the table and read off the level for the receiver to be tested (wave
quantity ax or bx).
Frequency
Output level
Displayed level ax
Displayed level bx
(w/o Rec Att)
Displayed level bx
(with Rec Att)
10 MHz
-40 dBm
+16 dBm ± 5 dB
+6 dBm ± 5 dB
+7 dBm ± 4 dB
100 MHz
-40 dBm
-4 dBm ± 4 dB
-14 dBm ± 4 dB
-13 dBm ± 4 dB
1 GHz
-20 dBm
1 dBm ± 4 dB
-9 dBm ± 4 dB
-8 dBm ± 4 dB
3 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-8 dBm ± 4 dB
8 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-8 dBm ± 4 dB
10 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-8 dBm ± 4 dB
12 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-8 dBm ± 4 dB
15 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-7 dBm ± 4 dB
18 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-7 dBm ± 4 dB
20 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-7 dBm ± 4 dB
25 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-6 dBm ± 4 dB
30 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-6 dBm ± 4 dB
35 GHz
-20 dBm
3 dBm ± 4 dB
-8 dBm ± 4 dB
-5 dBm ± 4 dB
40 GHz
-20 dBm
3 dBm ± 4 dB
-8 dBm ± 4 dB
-5 dBm ± 4 dB
45 GHz
-20 dBm
5 dBm ± 4 dB
-8 dBm ± 4 dB
-5 dBm ± 4 dB
50 GHz
-20 dBm
5 dBm ± 4 dB
-7 dBm ± 4 dB
-4 dBm ± 4 dB
55 GHz
-20 dBm
5 dBm ± 4 dB
-7 dBm ± 4 dB
-4 dBm ± 4 dB
60 GHz
-20 dBm
7 dBm ± 4 dB
-6 dBm ± 4 dB
-3 dBm ± 4 dB
67 GHz
-20 dBm
7 dBm ± 4 dB
-6 dBm ± 4 dB
-3 dBm ± 4 dB
With the stated levels, the cable loss must still be taken into account.
If the measured values are more than 2 dB below the levels list in the table, the board must be
replaced.
1145.1155.82
3.97
E-5
Troubleshooting
R&S ZVA
Coupler levels
The following is assumed:
• One reflectometer in the instrument is OK.
Method 1:
The generator section of the associated reflectometer is OK (output level at the port meets
specifications).
Loosen cable at coupler MEAS_OUT and at coupler REF_OUT at both ends and disconnect at the
coupler.
Connect the coupler output (MEAS = connector X3 or REF = connector X4) to a functioning port.
Terminate the coupler output that is not used.
Set the frequencies and levels listed in the table for the reflectometer associated with the coupler
(port) and measure the level (wave quantity bx) at the port used for the measurement as follows:
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Frequency
Level
Output level MEAS
Output level REF
10 MHz
0 dBm
-46 dBm ± 4 dB
-54 dBm ± 4 dB
100 MHz
0 dBm
-26 dBm ± 4 dB
-34 dBm ± 4 dB
1 GHz
0 dBm
-11 dBm ± 4 dB
-19 dBm ± 4 dB
3 GHz
0 dBm
-11 dBm ± 4 dB
-20 dBm ± 4 dB
8 GHz
0 dBm
-11 dBm ± 4 dB
-19.5 dBm ± 4 dB
10 GHz
0 dBm
-11 dBm ± 4 dB
-19.5 dBm ± 4 dB
12 GHz
0 dBm
-11 dBm ± 4 dB
-19.5 dBm ± 4 dB
15 GHz
0 dBm
-11 dBm ± 4 dB
-19 dBm ± 4 dB
18 GHz
0 dBm
-11 dBm ± 4 dB
-19 dBm ± 4 dB
20 GHz
0 dBm
-11 dBm ± 4 dB
-19 dBm ± 4 dB
25 GHz
0 dBm
-11 dBm ± 4 dB
-19 dBm ± 4 dB
30 GHz
0 dBm
-11 dBm ± 4 dB
-19 dBm ± 4 dB
35 GHz
0 dBm
-12 dBm ± 4 dB
-19.5 dBm ± 4 dB
40 GHz
0 dBm
-12 dBm ± 4 dB
-19.5 dBm ± 4 dB
45 GHz
0 dBm
-12 dBm ± 4 dB
-21 dBm ± 4 dB
50 GHz
0 dBm
-13 dBm ± 4 dB
-21 dBm ± 4 dB
55 GHz
0 dBm
-13 dBm ± 4 dB
-21 dBm ± 4 dB
60 GHz
0 dBm
-14 dBm ± 4 dB
-22.5 dBm ± 4 dB
67 GHz
0 dBm
-14 dBm ± 4 dB
-22 dBm ± 4 dB
With the stated levels, the cable loss must still be taken into account.
If the measured values are more than 2 dB below the levels in the table, the coupler must be replaced.
1145.1155.82
3.98
E-5
R&S ZVA
Troubleshooting
Method 2:
The receiver section of the associated reflectometer is OK.
Loosen the cable at coupler GEN_IN at both ends and screw off at the coupler.
Connect the coupler (connector X1) to a functioning port.
Set the frequencies and levels listed in the table at the port used for the measurement and measure
the level (wave quantity ax or bx) at the reflectometer associated with the coupler (port) as follows:
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Frequency
Level
level ax and bx
10 MHz
0 dBm
> -2 dBm
100 MHz
0 dBm
> -2 dBm
1 GHz
0 dBm
> -2 dBm
3 GHz
0 dBm
> -2.1 dBm
8 GHz
0 dBm
> -2.3 dBm
10 GHz
0 dBm
> -2.4 dBm
12 GHz
0 dBm
> -2.5 dBm
15 GHz
0 dBm
> -2.6 dBm
18 GHz
0 dBm
> -2.7 dBm
20 GHz
0 dBm
> -2.8 dBm
25 GHz
0 dBm
> -3 dBm
30 GHz
0 dBm
> -3.2 dBm
35 GHz
0 dBm
> -3.4 dBm
40 GHz
0 dBm
> -3.6 dBm
45 GHz
0 dBm
> -3.8 dBm
50 GHz
0 dBm
> -4 dBm
55 GHz
0 dBm
> -4.2 dBm
60 GHz
0 dBm
> -4.4 dBm
67 GHz
0 dBm
> -4.7 dBm
With the stated levels, the cable loss must still be taken into account.
If the measured values are more than 2 dB below the levels given in the table, the coupler unit must be
replaced.
1145.1155.82
3.99
E-5
Troubleshooting
R&S ZVA
Coupler Directivity
The following is assumed:
• The generator and receiver sections of the reflectometer associated with the coupler are OK.
Perform a sweep from 10 MHz to 67 GHz, measure Ratio bx/ax Source Portx
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector, save measured values (More Mem :
Data -> Mem3).
Screw the MATCH from the calibration kit to the port connector.
Select User Def Math : linMag(Data) / (linMag(Mem2) + linMag(Mem3)) / 2 : Math = User Def
The trace gives the directivity.
Frequency range
Directivity
10 MHz to 20 GHz
< -14 dB
20 GHz to 35 GHz
< -10 dB
35 GHz to 40 GHz
< -8 dB
40 GHz to 50 GHz
< -6 dB
50 GHz to 67 GHz
< -3 dB
If the measured values are more than 2 dB greater than the values stated in the table, the coupler must
be replaced.
Coupler Port Matching
It is assumed that there is a functioning reflectometer in the instrument.
Loosen cables W514A (GEN -> coupler), W515A (coupler -> MEAS) and W518A (coupler -> REF)
at both ends and unscrew at the coupler.
Terminate the coupler input and coupler outputs with three K-terminations (three V-terminations).
Connect test cable to a functioning instrument port and perform a 1-port calibration at the end of the
cable.
Connect the end of the test cable to the port of the coupler under test and display the Sxx
magnitude on the screen.
Frequency range
Sxx dB
10 MHz to 5GHz
< -20 dB
5 GHz to 20 GHz
< -15 dB
20 GHz to 30 GHz
< -12 dB
30 GHz to 40 GHz
< -11 dB
40 GHz to 60 GHz
< -10 dB
60 GHz to 67 GHz
< -6 dB
If the measured values are more than 2 dB greater than the values stated in the table, the coupler must
be replaced.
1145.1155.82
3.100
E-5
R&S ZVA
Troubleshooting
Testing the Network Controller Board
Testing the IF inputs
It is assumed that there is one functioning reflectometer in the instrument.
Disconnect the IF-MEAS and IF-REF cable from each of the reflectometers.
Connect the input to be tested at the end of the appropriate IF cable (W136, W137, W138, W139,
and W146, W147, W148, W149) to a functioning port using the adapter cable and SMA-N adapter .
Set the ZVA to CW sweep mode, CENTER 17.512345 MHz.
Setting at the port used for the measurement: POWER -10 dBm
Setting at the port associated with the network controller under test: WAVE QUANTITY ax or bx.
Enter service function 2.21.2.18.17512345 (IF = 17.512345 MHz).
Disable level corrections with SF 2.21[..24].2.15.1
If the level displayed on the ZVA's screen is not within the range -4 dBm ± 2 dB, the board must be
replaced.
1145.1155.82
3.101
E-5
Troubleshooting
R&S ZVA
Testing the Motherboard
28 V supply
Using a multimeter, measure the voltage at X 100.B5 (wrt ground).
Permissible deviation: ± 0.5 V
Preamplifier for DC measurement inputs
Apply the DC voltages listed in the table using the 4-pin Mini-DIN connector at the DC measurement
input.
Measure the DC voltage with a multimeter.
Input
Voltage
at
Gnd
APPLIED
VOLTAGE
Measurement at
Rated value
DC MEAS -1 V to +1 V
8
3, 5, 6
-1V
X 141.B10
2.33 V
DC MEAS -1 V to +1 V
6
3, 5, 8
+1V
X 141.B11
2.33 V
DC MEAS -10 V to +10 V
8
3, 5, 6
- 10 V
X 141.D10
2.33 V
DC MEAS -10 V to +10 V
6
3, 5, 8
+ 10 V
X 141.D11
2.33 V
Pin assignment DC MEAS connector
If the measured value is more than 10% above or more than 10% below the stated nominal value, the
motherboard must be replaced.
1145.1155.82
3.102
E-5
R&S ZVA
Instrument Construction and Function Description
Table of Contents - Chapter 3 "Repairs"
3
Repairs.......................................................................................................................................3.1
Instrument Construction and Function Description................................................................3.1
Block Diagram ............................................................................................................................3.2
Description of the Block Diagram ...............................................................................................3.4
Board Replacement...................................................................................................................3.21
Board Overview ........................................................................................................................3.22
Replacing Front Module Controller A90 ...................................................................................3.23
Replacing the Lithium Battery on the Front Module Controller.................................................3.26
Replacing Hard Disk A60..........................................................................................................3.30
Replacing LCD A70 and the DC/AC Converter ........................................................................3.31
Replacing Flexible switch board (Keyboard) A16 / Key Pad A15.............................................3.33
Replacing the Front Cover........................................................................................................3.35
Replacing Disk Drive A30 .........................................................................................................3.36
Replacing USB Board A40 .......................................................................................................3.37
Replacing Power Supply A20 ...................................................................................................3.38
Replacing Fuse board A21 .......................................................................................................3.39
Replacing a Fan........................................................................................................................3.40
Replacing Motherboard A10 .....................................................................................................3.41
Replacing a Reflectometer RM8 A510 to 540 ..........................................................................3.44
Replacing a Reflectometer RM8 A510 to 540 ..........................................................................3.44
Replacing Generator Board (ZVA8 only)..................................................................................3.45
Replacing Receiver Board (ZVA8 only)....................................................................................3.46
Replacing the Bridge Unit (ZVA8 only) .....................................................................................3.49
Replacing a Reflectometer RM24 A510 to 540 ........................................................................3.50
Replacing a Reflectometer RM40 and RM50 A510 to 540 ......................................................3.51
Replacing a Reflectometer RM67 A510 to 540 ........................................................................3.52
Replacing the Coupler Unit (ZVA67) ........................................................................................3.54
Replacing the Test Set (ZVA40 only) .......................................................................................3.54
Replacing the Reflectometer Fan .............................................................................................3.55
Replacing Network Controller Board A130, A140 ....................................................................3.57
Replacing Synthesizer Board A150, A160 ...............................................................................3.58
Replacing Frequency Reference Board A100 ..........................................................................3.59
Troubleshooting ........................................................................................................................3.60
Test Equipment and Accessories .............................................................................................3.61
Troubleshooting - Power-up Problems .....................................................................................3.62
Troubleshooting Boot Problems ...............................................................................................3.63
Troubleshooting - Boot Error ....................................................................................................3.64
Troubleshooting with the Selftest .............................................................................................3.65
Checking the Temperature Sensors .........................................................................................3.70
Service Functions .....................................................................................................................3.71
Determining which Boards are defective ..................................................................................3.75
Board Test ................................................................................................................................3.76
1145.1155.82
I-3.1
E-5
R&S ZVA
Instrument Construction and Function Description
3 Repairs
This chapter describes the R&S ZVA’s construction, simple procedures for repairs, troubleshooting and
board replacement. A selftest which checks the diagnostic voltages of the board and indicates limit
violations is provided for troubleshooting and diagnostics.
Chapter 4 of this service manual describes the installation of options and firmware updates.
Instrument Construction and Function Description
The R&S ZVA’s construction is shown schematically by the following block diagrams and the exploded
drawings (see Chapter 5).
The block diagram will help clarify the following function description of the instrument.
1145.1155.82
3.1
E-5
Instrument Construction and Function Description
R&S ZVA
Block Diagram
See also Chapter 5, Annex and Drawings.
BRIDGE PORT 1 (ZVA8)
COUPLER PORT 1 (ZVA24, 40, 50, 67)
GENERATOR
(Driver+Doubler)
PORT 1
PORT 1
15 to 21 MHz
RECEIVER
REF PORT 1
RECEIVER
MEAS PORT 1
NETCON
ANALOG
1
BRIDGE PORT 2 (ZVA8)
COUPLER PORT 2 (ZVA24, 40, 50, 67)
OPTION
GENERATOR
ATTENUATOR
NETCON
DIGITAL
1
CPU
GRAPHICS
DISPLAY
GENERATOR
(Driver+Doubler)
PORT 2
RECEIVER
REF PORT 2
OPTION
RECEIVER
ATTENUATOR
RECEIVER
MEAS PORT 2
SYNTHESIZER
FREQUENCY
REFERENCE
OPTION
OCXO
ZVAB-B4
POWER
SUPPLY
Fig. 3-1 Block diagram of the R&S ZVA8, R&S ZVA24, R&S ZVA40, R&S ZVA50 and R&S ZVA67
two ports
With option direct generator/receiver access on port1,
options generator and receiver attenuator on port2.
1145.1155.82
3.2
E-5
R&S ZVA
Instrument Construction and Function Description
BRIDGE PORT 1 (ZVA8)
COUPLER PORT 1 (ZVA24, 40, 50, 67)
PORT 1
PORT 1
GENERATOR
PORT 1
OPTION
GENERATOR
ATTENUATOR
15 to 21 MHz
RECEIVER
REF PORT 1
OPTION
RECEIVER
ATTENUATOR
RECEIVER
MEAS PORT 1
NETCON
ANALOG
1
BRIDGE PORT 2 (ZVA8)
COUPLER PORT 2 (ZVA24, 40, 50, 67)
NETCON
DIGITAL
1
GENERATOR
PORT 2
PORT 2
RECEIVER
REF PORT 2
RECEIVER
MEAS PORT 2
SYNTHESIZER 2
FREQUENCY
REFERENCE
SYNTHESIZER 1
OPTION
OCXO
ZVAB-B4
CPU
GRAPHICS
DISPLAY
BRIDGE PORT 3 (ZVA8)
COUPLER PORT 3 (ZVA24, 40, 50, 67)
OPTION
GENERATOR
ATTENUATOR
PORT 3
GENERATOR
PORT 3
15 to 21 MHz
RECEIVER
REF PORT 3
OPTION
RECEIVER
ATTENUATOR
Synthesizer
Synthesizer
PORT 4
RECEIVER
MEAS PORT 3
NETCON
ANALOG
2
NETCON
DIGITAL
2
GENERATOR
PORT 4
RECEIVER
REF PORT 4
RECEIVER
MEAS PORT 4
POWER
SUPPLY
Fig. 3-2 Block diagram of the R&S ZVA8, R&S ZVA24, R&S ZVA40, R&S ZVA50 and R&S
ZVA67 four ports
With option generator/receiver attenuator on port1,
option direct generator/receiver access on port2,
options generator/receiver attenuator and direct generator/receiver access on port3.
1145.1155.82
3.3
E-5
Instrument Construction and Function Description
R&S ZVA
Description of the Block Diagram
The block diagrams shown in Fig. 3-1 and Fig. 3-2 apply to the R&S ZVA8, the R&S ZVA24, the R&S
ZVA40, R&S ZVA50 and the R&S ZVA67 two-ports and four-ports.
The ZVA is a vector network analyzer covering 300 kHz to 8 GHz (R&S ZVA8), 10 MHz to 24 GHz
(R&S ZVA24), 10 MHz to 40 GHz (R&S ZVA40), 10 MHz to 50 GHz (R&S ZVA50) or 10 MHz to 67
GHz (R&S ZVA67). All R&S ZVA are available in a two-port or four-port version. The signals (including
the LO signal for the receiver) are generated using one or two synthesizer boards, depending on the
number of ports. The signal processing path comprises a reflectometer board, an IF board, a network
controller and a processor section, comprising a Pentium-PC, I/O interface and graphics board. The
instrument can be expanded to handle future digital and analog requirements by retrofitting options.
The generator signal on R&S ZVA8 (300 kHz to 8 GHz) is generated on synthesizer board 1, amplified
in the generator section of the reflectometer board and then passes via the bridge to the port (port1 to
4) and thus to the DUT. The reference signal (Ref1 to 4) is split in the bridge and fed to the receiver
section (Receiver Ref1 to 4) on the reflectometer board.
The generator signal on R&S ZVA24, R&S ZVA40, R&S ZVA50 and R&S ZVA67 (10 MHz to 24 GHz,
10 MHz to 40 GHz, 10 MHz to 50 GHz, 10 MHz to 67 GHz) is generated on synthesizer board1,
frequency multiplied, filtered and amplified in the generator section of the reflectometer board and then
passes via the coupler to the port (port1 to 4) and thus to the DUT. The reference signal (Ref1 to 4) is
split in the coupler and fed to the receiver section (Receiver Ref1 to 4) on the reflectometer board.
The signal reflected or transmitted by the DUT (Meas1 to 4) is fed to the port, coupled out in the bridge
or coupler unit and fed to the receiver section (Receiver Meas 1 to 4) on the reflectometer board.
The internal reference frequencies are generated on the frequency reference board. The 128-MHz
reference frequency is generated there as an internal device reference.
The following sections describe the various boards in greater detail.
Reflectometer ZVA8
A reflectometer board comprising a bridge unit, a generator section (Generator) and a receiver
section (Receiver) is incorporated in every port (Port1 to 4). These three components are screwed
together to form a compact unit.
Bridge unit
The bridge unit is a resistive coupler which is used to separate the signal going to the DUT from the
signal coming from the DUT. The reference signal (= measure of the signal to the DUT) is also obtained
from the bridge unit. The reference signal provides a reference for relative measurements.
Generator
The generator contains three broadband amplifier stages which boost the signal coming from the
synthesizer to a level > 20 dBm. Limiter diodes protect the output stage from ESDs. A total of three
adjustable attenuators form the setting element to keep the output level constant and to attenuate it
electronically.
1145.1155.82
3.4
E-5
R&S ZVA
Instrument Construction and Function Description
Receiver
The receiver section has two channels (measurement channel and reference channel) and uses single
conversion. Every channel contains a buffer amplifier, for each of the frequency ranges 300 kHz to
4 GHz and 4 GHz to 8 GHz, a mixer with LO amplifiers and an IF amplifier. In the mixer, the input signal
is directly converted to the IF range, approx 15 to 21 MHz. The inputs are protected by limiter diodes.
Reflectometer Unit ZVA24
A reflectometer unit comprising a coupler unit, a generator section (Generator) and a receiver
section (Receiver) is incorporated in every port (Port1 to 4). The Generator and the Receiver are
screwed together to form a compact unit.
Coupler unit
The coupler unit contains a bias-T and two directional couplers. One coupler is used to separate the
signal going to the DUT from the signal coming from the DUT. The reference signal (= measure of the
signal to the DUT) is obtained from the second coupler. The reference signal provides a reference for
relative measurements.
Generator
The generator contains a frequency doubler for the range 8 GHz to 16 GHz, a switchable filter unit, a
second frequency doubler with filter for the range 16 GHz to 24 GHz and a broadband amplifier for the
frequency range 10 MHz to 24 GHz with two adjustable attenuators to keep the output level constant
and to attenuate it electronically.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
10 MHz to 8.0 GHz
---
10 MHz to 8.0 GHz
---
10 MHz to 8.0 GHz
2
4 GHz to 5.05 GHz
x
8.0 GHz to 10.1 GHz
---
8.0 GHz to 10.1 GHz
3
5.05 GHz to 6.35 GHz
x
10.1 GHz to 12.7 GHz
---
10.1 GHz to 12.7 GHz
4
6.35 GHz to 8.0 GHz
x
12.7 GHz to 16.0 GHz
---
12.7 GHz to 16.0 GHz
5
4.0 GHz to 5.0 GHz
x
8.0 GHz to 10.0 GHz
x
16.0 GHz to 20 GHz
6
5.0 GHz to 6.0 GHz
x
10.0 GHz to 12.0 GHz
x
20.0 GHz to 24 GHz
Receiver
The receiver section has two channels (measurement channel and reference channel) and uses single
conversion. The measurement channel contains a buffer amplifier, two mixers for each of the frequency
ranges 10 MHz to 2.5 GHz and 2.5 GHz to 24 GHz, LO amplifiers and an IF amplifier. The reference
channel is identical to the measurement channel without the buffer amplifier. In the mixers, the input
signal is directly converted to the IF range, approx. 15 to 21 MHz. The mixers are used as basic wave
mixers.
The LO signal section contains a frequency doubler for the range 8 GHz to 16 GHz, a switchable filter
unit, a second frequency doubler with filter for the range 16 GHz to 24 GHz and a broadband amplifier
for the frequency range 30 MHz to 24 GHz.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
30 MHz to 8.0 GHz
---
30 MHz to 8.0 GHz
---
30 MHz to 8.0 GHz
2
4 GHz to 8.0 GHz
x
8.0 GHz to 16.0 GHz
---
8.0 GHz to 16.0 GHz
3
4.0 GHz to 6.0 GHz
x
8.0 GHz to 12.0 GHz
x
16.0 GHz to 24.0 GHz
Each of the reflectometers contains a voltage-controlled fan to perform optimum cooling.
1145.1155.82
3.5
E-5
Instrument Construction and Function Description
R&S ZVA
Reflectometer Unit R&S ZVA40
A reflectometer unit comprising a coupler, a generator section (Driver24 and Doubler44) and a
receiver section (Receiver44) is incorporated in every port (Port1 to 4). The generator and the
receiver are screwed together to form a compact unit.
Coupler Unit
The coupler contains a bias-T and two directional couplers. One coupler is used to separate the signal
going to the DUT from the signal coming from the DUT. The reference signal (= measure of the signal
to the DUT) is obtained from the second coupler. The reference signal provides a reference for relative
measurements.
Driver24
The driver contains a frequency doubler for the range 8 GHz to 16 GHz, a switchable filter unit, a
second frequency doubler with filter for the range 16 GHz to 24 GHz and a broadband amplifier for the
frequency range 10 MHz to 24 GHz with two adjustable attenuators to keep the output level constant
and to attenuate it electronically.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
10 MHz to 8.0 GHz
---
10 MHz to 8.0 GHz
---
10 MHz to 8.0 GHz
2
4 GHz to 5.05 GHz
x
8.0 GHz to 10.1 GHz
---
8.0 GHz to 10.1 GHz
3
5.05 GHz to 6.35 GHz
x
10.1 GHz to 12.7 GHz
---
10.1 GHz to 12.7 GHz
4
6.35 GHz to 8.0 GHz
x
12.7 GHz to 16.0 GHz
---
12.7 GHz to 16.0 GHz
5
4.0 GHz to 5.0 GHz
x
8.0 GHz to 10.0 GHz
x
16.0 GHz to 20 GHz
6
5.0 GHz to 6.0 GHz
x
10.0 GHz to 12.0 GHz
x
20.0 GHz to 24 GHz
Doubler44
The doubler contains a frequency doubler for the range 24 GHz to 44 GHz, a switchable filter unit and a
broadband amplifier for the range 10 MHz to 44 GHz.
Range
Frequency range from
driver24
Doubler
Output frequency
1
10 MHz to 24.0 GHz
---
10 MHz to 24.0 GHz
2
12.0 GHz to 14.9 GHz
x
24.0 GHz to 29.8 GHz
3
14.9 GHz to 18.5 GHz
x
29.8 GHz to 37.0 GHz
4
18.5 GHz to 22.0 GHz
x
37.0 GHz to 44.0 GHz
Receiver44
The receiver section has two channels (measurement channel and reference channel). The
measurement channel contains a buffer amplifier, two mixers for each of the frequency ranges 10 MHz
to 2.5 GHz and 2.5 GHz to 44 GHz, LO doublers, LO amplifiers and an IF amplifier. The reference
channel is identical to the measurement channel without the buffer amplifier. In the mixers, the input
signal is directly converted to the IF range, approx. 15 to 21 MHz. In the frequency range 10 MHz to 24
GHz the mixers are used as basic wave mixers (IF = LO – RF). In the range 24 GHz to 44 GHz the
mixer for the upper frequency range works as a harmonic mixer (IF = 3LO – RF).
1145.1155.82
3.6
E-5
R&S ZVA
Instrument Construction and Function Description
The LO signal section contains a frequency doubler for the range 8 GHz to 16 GHz, a switchable filter
unit, a second frequency doubler with filter for the range 16 GHz to 24 GHz and a broadband amplifier
for the frequency range 30 MHz to 24 GHz.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
30 MHz to 8.0 GHz
---
30 MHz to 8.0 GHz
---
30 MHz to 8.0 GHz
2
4 GHz to 8.0 GHz
x
8.0 GHz to 16.0 GHz
---
8.0 GHz to 16.0 GHz
3
4.0 GHz to 6.0 GHz
x
8.0 GHz to 12.0 GHz
---
16.0 GHz to 24.0 GHz
Each of the reflectometers RM1 and RM2 contain two voltage-controlled fans to perform optimum
cooling.
Reflectometer Unit R&S ZVA50
A reflectometer unit comprising a coupler, a generator section (Driver24 and Doubler50) and a
receiver section (Receiver50) is incorporated in every port (Port1 to 4). The generator and the
receiver are screwed together to form a compact unit.
Coupler Unit
The coupler contains a bias-T and two directional couplers. One coupler is used to separate the signal
going to the DUT from the signal coming from the DUT. The reference signal (= measure of the signal
to the DUT) is obtained from the second coupler. The reference signal provides a reference for relative
measurements.
Driver24
The driver is the same as it is used in ZVA40. Frequency range 6 is extended to 25 GHz.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
10 MHz to 8.0 GHz
---
10 MHz to 8.0 GHz
---
10 MHz to 8.0 GHz
2
4 GHz to 5.05 GHz
x
8.0 GHz to 10.1 GHz
---
8.0 GHz to 10.1 GHz
3
5.05 GHz to 6.35 GHz
x
10.1 GHz to 12.7 GHz
---
10.1 GHz to 12.7 GHz
4
6.35 GHz to 8.0 GHz
x
12.7 GHz to 16.0 GHz
---
12.7 GHz to 16.0 GHz
5
4.0 GHz to 5.0 GHz
x
8.0 GHz to 10.0 GHz
x
16.0 GHz to 20 GHz
6
5.0 GHz to 6.25 GHz
x
10.0 GHz to 12.5 GHz
x
20.0 GHz to 25 GHz
1145.1155.82
3.7
E-5
Instrument Construction and Function Description
R&S ZVA
Doubler50
The doubler contains a frequency doubler for the range 25 GHz to 50 GHz, a switchable filter unit and a
broadband amplifier for the range 10 MHz to 50 GHz.
Range
Frequency range from
driver24
Doubler
Output frequency
1
10 MHz to 25.0 GHz
---
10 MHz to 25.0 GHz
2
12.5 GHz to 14.9 GHz
x
25.0 GHz to 29.8 GHz
3
14.9 GHz to 18.5 GHz
x
29.8 GHz to 37.0 GHz
4
18.5 GHz to 25.0 GHz
x
37.0 GHz to 50.0 GHz
Receiver50
The receiver section has two channels (measurement channel and reference channel). The
measurement channel contains a buffer amplifier, two mixers for each of the frequency ranges 10 MHz
to 2.5 GHz and 2.5 GHz to 50 GHz, LO doublers, LO amplifiers and an IF amplifier. The reference
channel is identical to the measurement channel without the buffer amplifier. In the mixers, the input
signal is directly converted to the IF range, approx. 15 to 21 MHz. In the frequency range 10 MHz to 24
GHz the mixers are used as basic wave mixers (IF = LO – RF). In the range 24 GHz to 50 GHz the
mixer for the upper frequency range works as a harmonic mixer (IF = 3LO – RF).
The LO signal section contains a frequency doubler for the range 8 GHz to 16 GHz, a switchable filter
unit, a second frequency doubler with filter for the range 16 GHz to 24 GHz and a broadband amplifier
for the frequency range 30 MHz to 24 GHz.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
30 MHz to 8.0 GHz
---
30 MHz to 8.0 GHz
---
30 MHz to 8.0 GHz
2
4 GHz to 8.0 GHz
x
8.0 GHz to 16.0 GHz
---
8.0 GHz to 16.0 GHz
3
4.0 GHz to 6.0 GHz
x
8.0 GHz to 12.0 GHz
---
16.0 GHz to 24.0 GHz
Each of the reflectometers RM1 and RM2 contain two voltage-controlled fans to perform optimum
cooling.
Reflectometer Unit ZVA67
A reflectometer unit comprising a coupler, a generator section (Driver42 and Doubler67) and a
receiver section (Receiver67) is incorporated in every port (Port1 to 4). The generator and the
receiver are screwed together to form a compact unit.
Coupler Unit
The coupler contains a bias-T and two directional couplers. One coupler is used to separate the signal
going to the DUT from the signal coming from the DUT. The reference signal (= measure of the signal
to the DUT) is obtained from the second coupler. The reference signal provides a reference for relative
measurements.
1145.1155.82
3.8
E-5
R&S ZVA
Instrument Construction and Function Description
Driver42
The driver contains a frequency doubler for the range 12 GHz to 24 GHz with a switchable filter unit and
a second frequency doubler with a switchable filter unit for the range 24 GHz to 42 GHz. Switchable
amplifiers and attenuators and two adjustable attenuators are used to keep the output level constant
and to attenuate it electronically.
Range
Basic frequency range
from synthesizer
Doubler 1
Frequency
Doubler 2
Output frequency
1
10 MHz to 12.0 GHz
---
10 MHz to 12.0 GHz
---
10 MHz to 12.0 GHz
2
6.0 GHz to 6.75 GHz
x
12.0 GHz to 13.5 GHz
---
12.0 GHz to 13.5 GHz
3
6.75 GHz to 9.0 GHz
x
13.5 GHz to 18.0 GHz
---
13.5 GHz to 18.0 GHz
4
9.0 GHz to 12.0 GHz
x
18.0 GHz to 24.0 GHz
---
18.0 GHz to 24.0 GHz
5
6.0 GHz to 6.75 GHz
x
12.0 GHz to 13.5 GHz
x
24.0 GHz to 27.0 GHz
6
6.75 GHz to 9.0 GHz
x
13.5 GHz to 18.0 GHz
x
27.0 GHz to 36.0 GHz
7
9.0 GHz to 10.5 GHz
x
18.0 GHz to 21.0 GHz
x
36.0 GHz to 42.0 GHz
Doubler67
The doubler contains a frequency doubler for the range 40 GHz to 70 GHz, a switchable filter unit and a
broadband amplifier for the range 10 MHz to 70 GHz.
Range
Frequency range from
driver42
Doubler
Output frequency
1
10 MHz to 41.6 GHz
---
10 MHz to 41.6 GHz
2
20.8 GHz to 27.0 GHz
x
41.6 GHz to 54.0 GHz
3
27.0 GHz to 35.0 GHz
x
54.0 GHz to 70.0 GHz
Receiver67
The receiver section has two channels (measurement channel and reference channel). The
measurement channel contains a buffer amplifier, two mixers for each of the frequency ranges 10 MHz
to 2.5 GHz and 2.5 GHz to 70 GHz, LO doublers, LO amplifiers and an IF amplifier. The reference
channel is identical to the measurement channel without the buffer amplifier. In the mixers, the input
signal is directly converted to the IF signal 17.5 MHz. In the frequency range 10 MHz to 24 GHz the
mixers are used as basic wave mixers (IF = LO – RF). In the range 24 GHz to 70 GHz the mixer for the
upper frequency range works as a harmonic mixer (IF = 3LO – RF).
The LO signal section contains a frequency doubler for the range 12 GHz to 24 GHz, a switchable filter
unit, an adjustable attenuator and a broadband amplifier for the frequency range 30 MHz to 24 GHz.
Range
1145.1155.82
Basic frequency range
from synthesizer
Doubler
Output frequency
1
30 MHz to 12.0 GHz
---
30 MHz to 12.0 GHz
2
6 GHz to 8.15 GHz
x
12.0 GHz to 16.3 GHz
3
8.15 GHz to 12.0 GHz
x
16.3 GHz to 24.0 GHz
3.9
E-5
Instrument Construction and Function Description
R&S ZVA
Each of the reflectometers RM1 and RM2 contain two voltage-controlled fans to perform optimum
cooling.
Network controller
The network controller comprises two boards, the netcon analog and the netcon digital which are
screwed together to form a single unit. The boards are four-channel – in other words, one network
controller is required for two ports (2 measurement channels + 2 reference channels). After A/D
conversion, the network controller performs high-speed digital processing on the IF signals from the
reflectometers.
Netcon analog
The netcon analog board is a 4-channel IF amplifier and one 14-bit A/D converter per channel. The
transmission bandwidth is 13 MHz to 26 MHz. A dither generator is used to linearize the A/D-converter
characteristic. The board also accommodates a temperature sensor which is only used for general
temperature checks and not to correct measurement results.
Netcon digital
The netcon digital board further processes the digitized raw data from the netcon analog board. Speed
considerations mean that digital signal processing is performed in an ASIC which has a clock frequency
of 80 MHz.
The main functions on the board are:
• Mixing to the baseband
• Filter with bandwidths from 1 Hz to 100 kHz in 1/3/5 sequence
• Detectors, PCI interface
• Setting and routine control
The current measured value (sample), the average, the RMS and the Max can be recorded
simultaneously and passed on to the main processor via the PCI-bus. The connection to the PCI-bus is
made via the PCINT-FPGA. A further FPGA "FCON" contains the central section of the procedure
control from measurement point to measurement point and the trigger control. This FPGA is configured
by the main processor.
The A/D converters for ext. DC measurements are also accommodated on the netcon digital board.
Frequency reference
The frequency reference board generates the highly stable and spectrally pure clock signals, required
by the ZVA, which can be phase-locked to external synchronisation signals.
The various function blocks are:
The 128 MHz VCXO (voltage-controlled crystal oscillator) which generates a stable, low-noise
reference frequency for the synthesisers, for the A/D converters and for digital signal processing.
The PLL for phase locking the VCXO signal to an external reference signal or to a 10 MHz OCXO
(oven-controlled crystal oscillator) option.
1145.1155.82
3.10
E-5
R&S ZVA
Instrument Construction and Function Description
The VCO and PLL which generate the clock for the netcon digital board (locked to the 128 MHz VCXO).
The frequency can be varied from 75 MHz to 86 MHz. The VCO frequency is programmable;-the
nominal clock frequency is 80 MHz.
A reference frequency of 10 MHz is standard. If the OCXO is fitted, the OCXO signal is brought out at
the ZVA’s rear panel (10 MHz REF) so that further instruments can be synchronised.
The free-running VCXO (no OCXO, no external reference) can be calibrated using a pre-tune voltage.
If no OCXO is fitted, a 10 MHz signal is still output at the instrument’s rear panel. It is derived from the
80 MHz signal which is divided down to 10 MHz by the divider for the OCXO.
The following are also accommodated on the board:
- A control-CPLD to act as an interface between the serial bus and the board,
- Register for storing divider values,
- D/A converter for pre-tuning the VCXO and OCXO
- An on-board EEPROM for storing board-specific data
- Selftest facilities
OCXO reference (option B4)
As an option, the frequency reference board can be fitted to an OCXO (oven-controlled crystal
oscillator) which considerably improves the phase noise of the reference signal close to the carrier,
short-term stability and long-term stability.
1145.1155.82
3.11
E-5
Instrument Construction and Function Description
R&S ZVA
Synthesizers
The source signals for the generator signals associated with each port and the LO signal for the mixers
on the receiver boards for each of the reflectometers are generated on the synthesizer board. One or
two individual synthesizers are accommodated on a synthesizer board. There are three different
synthesizer types used in the ZVA models:
Synthesizer-LS
to Reflectometer 1
(GEN)
Synthesizer
9 kHz to 8GHz
to Reflectometer 2
(GEN)
to Reflectometer 1
(LO)
Synthesizer
15.625 MHz to
8025 MHz
to Reflectometer 2
(LO)
1145.1155.82
3.12
E-5
R&S ZVA
Instrument Construction and Function Description
Synthesizer-DS
to Reflectometer 1
(GEN)
Synthesizer
9 kHz to 8GHz
to Reflectometer 2
(GEN)
to Reflectometer 3
(GEN)
Synthesizer
9 kHz to 8GHz
1145.1155.82
3.13
E-5
Instrument Construction and Function Description
R&S ZVA
Synthesizer-LO
to Reflectometer 1
(LO)
to Reflectometer 2
(LO)
Synthesizer
15.625 MHz to
8025 MHz
to Reflectometer 3
(LO)
to Reflectometer 4
(LO)
1145.1155.82
3.14
E-5
R&S ZVA
Instrument Construction and Function Description
Synthesizer-12 1305.3020.02
Synthesizer
30 MHz to 12 GHz
LO Reflectometer 1
Synthesizer
30 MHz to 12 GHz
LO Reflectometer 2
Synthesizer
GEN Reflectometer 1
10 MHz to 12 GHz
Synthesizer
GEN Reflectometer 2
10 MHz to 12 GHz
1145.1155.82
3.15
E-5
Instrument Construction and Function Description
R&S ZVA
Synthesizer-12 1305.1702.03
Synthesizer
GEN Reflectometer 1
10 MHz to 12 GHz
Synthesizer
GEN Reflectometer 3
10 MHz to 12 GHz
Synthesizer
10 MHz to 12 GHz
GEN Reflectometer 2
Synthesizer
GEN Reflectometer 4
10 MHz to 12 GHz
1145.1155.82
3.16
E-5
R&S ZVA
Instrument Construction and Function Description
Synthesizer-12 1305.xxxx.04
LO Reflectometer 1
Synthesizer
30 MHz to 12 GHz
LO Reflectometer 3
LO Reflectometer 2
LO Reflectometer 4
Synthesizer
30 MHz to 12 GHz
1145.1155.82
3.17
E-5
Instrument Construction and Function Description
R&S ZVA
The synthesizer models are incorporated as follows in the various ZVA models:
Synthesizer-
LS
1302.4025.02
LS
1302.4025.20
DS
1302.5180.02
LO
1302.4248.02
LO
1302.4248.20
12
1305.3020.02
ZVA8 two-port
2x SRC, 2x LO
--------
--------
--------
--------
--------
ZVA8 four-port
--------
--------
4x SRC
4x LO
--------
--------
ZVA24 two-port
2x SRC, 2x LO
--------
--------
--------
--------
--------
ZVA24 four-port
--------
--------
4x SRC
4x LO
--------
--------
ZVA40 two-port
--------
2x SRC, 2x LO
--------
--------
--------
--------
ZVA40 four-port
--------
--------
4x SRC
--------
4x LO
--------
ZVA50 two-port
--------
2x SRC, 2x LO
--------
--------
--------
--------
ZVA50 four-port
--------
--------
4x SRC
--------
4x LO
--------
ZVA67 two-port
--------
--------
--------
--------
--------
2x SRC, 2x LO
(one board)
ZVA67 four-port
--------
--------
--------
--------
--------
4x SRC, 4x LO
(two boards)
Front unit
The front unit comprises a mounting plate on which the LCD, the flexible switch board and key pad, and
the tachogenerator are accommodated.
The front module controller is mounted in the controller tray in the instrument frame.
LC display
All results and setting information the user requires is displayed on the colour LCD.
The resolution of the LCD is 800 x 600 pixels (SVGA).
The display has an integral cold-cathode tube to provide illumination. The high voltage that is required is
provided by a dedicated DC/AC converter. The converter is mounted on the mounting plate next to the
display and connected to both the display and the controller board via a cable.
Keyboard
The keyboard comprises a flexible switch board and a key pad. They make contact whenever a rubber key
is pressed. The two LEDs for the status display associated with the Standby/On key (yellow for
standby/green for on) are also accommodated on the key pad.
Key detection and LED control are performed via a foil cable connection on the controller board. They are
controlled by means of a matrix method implemented by a special microprocessor on the controller board;
the two LEDs are controlled accordingly. When the instrument is turned off at the mains switch, the
microprocessor saves the status of the Standby/On key.
1145.1155.82
3.18
E-5
R&S ZVA
Instrument Construction and Function Description
Front module controller
The front module controller accommodates all the components that are required on one board - for example,
the processor, memory chips (SIMMs), I/O chips (ISA bus), the lithium battery, IEC/IEEE bus controller, two serial
interfaces (COM1/2), a parallel interface (LPT), LCD graphics controller, external VGA-monitor graphics
interface (Monitor) and a connector for an external keyboard (keyboard PS/2). Also integrated on the
controller board are a floppy controller for an external disk drive and an IDE hard-drive controller.
In the case of the FMR6, the LAN interface is also integrated on the controller board.
Hard disk
The hard disk is screwed to the rear of the tray for the front module controller with a holder and
connected to the board with a flat cable.
Power supply
The power supply produces all the voltages required to power the ZVA. It can be turned off with a
switch on the instrument’s rear panel.
The power supply is a primary-switched power supply with power factor correction (PFC) and standby
circuit (+12 V standby).
On the secondary side, it outputs DC voltages (+3.4 V, +5.2 V, +6.5 V, +8.25 V, +12.25 V, +12 V
standby, -12.25 V).
The control signal RS_PS_ON which is controlled by the front module controller (via the STANDBY/ON
key at the front of the instrument frame), activates the power supply. In the standby mode, the power
supply generates only the 12-V standby voltage to supply a crystal oven and the STANDBY status
display on the front panel.
The secondary voltages are open-proof and short-proof to ground and mutually open-proof and shortproof.
A circuit that prevents overheating is also provided. Overheating is indicated to the front module
controller via a status signal (OT).
Motherboard
The motherboard supplies power to the boards and connects them to the control and data buses. A
number of RF connections are also routed via the motherboard.
As well as straight connections, a number of circuits are accommodated on the motherboard:
Motherboard controller (MBCON)
28 V supply
Preamplifier for the DC measurement inputs
Supply voltage fuses
Rear panel interfaces
Fan control
The MBCON unit acts as an FSU bus-slave:
•
•
•
•
•
to drive the LEDs (instrument front-panel)
to drive the fan in five stages
for two temperature sensors on the motherboard
for an SPI-EEPROM on the motherboard
Furthermore, the software can detect which device (ZVA8 or ZVA24) is present using the MBCON.
1145.1155.82
3.19
E-5
Instrument Construction and Function Description
R&S ZVA
In addition to the voltages delivered by the power supply, +28 V is produced from +12 V on the
motherboard by means of a boosting switching regulator. This voltage is required to operate the OCXO
on the reference board when option B4 is fitted.
Each board has its own fuses for the supply voltages. These fuses are soldered into position on the
board.
All external supply voltages (USB etc.) are protected to prevent shorts.
1145.1155.82
3.20
E-5
R&S ZVA
Board Replacement
Board Replacement
The following section is a detailed description of board replacement. Chapter 5 tells you how to order
spare parts. It contains a list of mechanical parts and their order numbers as well as drawings relating
to board replacement.
Note:
The numbers in brackets are the item numbers in the list of mechanical parts in Chapter 5.
In turn, these item numbers are the same as the item numbers in the drawings relating to
board replacements (also in Chapter 5):
1145.1110 sheet 1 (ZVA Network Analyzer)
1145.1110 sheet 2, 3, 4, 5, 6, 7 (ZVA Network Analyzer)
1305.7002 sheet 1, 2, 3 (ZVA67 Network Analyzer)
1145.1290 sheet 2 (ZVB base instrument, power supply cabeling)
1145.1310 sheet 1, 2 (ZVA base instrument)
1145.1390 sheet 1 (ZVA display unit)
1164.1770 sheet 1 (ZVA Option B4)
1145.3593 sheet 1 (8GHz Bridge)
1145.4177 sheet 1 (RM8)
1145.4283 sheet 1 (RM24)
1145.4319 sheet 1 (RM40)
1305.3413 sheet 1 (RM50)
1305.6241 sheet 1 and 2 (RM67)
1164.0250 sheet 1 to 5 (ZVA8 Option B16)
1164.0267 sheet 1 to 5 (ZVA24 Option B16)
1164.0215 sheet 1 to 5 (ZVA8 Option B21 to B24 and B31 to B34)
1164.0221 sheet 1 to 5 (ZVA24 Option B21 to B24 and B31 to B34)
1164.0409 sheet 1 to 8 (ZVA40 Option B21 to B24 and B31 to B34)
1302.4960.08 sheet 1 (RM Unit ZVB4/8)
1302.5621 sheet 1 (RM44 Blower Attachement)
1145.1155.82
3.21
E-5
Board Replacement
R&S ZVA
Board Overview
Table 3-1
Overview: Board Replacement
Board
Measures taken after replacement
Function test
Front module controller
Check error log
Lithium battery
Check error log
Hard disk
Check error log
LC display / DC/AC converter
Functional test
Flexible switch board (keyboard)/
key pad
Functional test
Alignment
Recording of correction
values
System error calibration
Other
BIOS update
System error calibration
FW update
Front cover
Disk drive
Check the directory structure
USB board
Test with mouse, keyboard
Power supply
Check error log
Fan
Motherboard
Check error log
System error calibration
Alignment DC measurement
inputs
Reflectometer
Check error log
Record correction values
System error calibration
Input connector port 1 to 4
(R&S ZVA8 only)
Check error log
System error calibration
Bridge unit
(R&S ZVA8 only)
Check error log
Record correction values
System error calibration
Coupler unit
(R&S ZVA24, R&S ZVA40,
R&S ZVA50 and R&S ZVA67
only)
Check error log
Record correction values
System error calibration
Reflectometer fan
Check error log
Network controller
Check error log
Record correction values
System error calibration
Alignment DC measurement
inputs
Synthesizer
Check error log
Record correction values
System error calibration
LO divider
Check error log
Record correction values
System error calibration
Frequency reference
Check error log
Alignment
Frequency accuracy
1145.1155.82
3.22
E-5
R&S ZVA
Board Replacement
Replacing Front Module Controller A90
(See Chapter 5, Spare Parts List, Item 580, and drawings 1145.1110, 1145.1310)
The front module controller is located behind the front unit.
Opening the instrument and removing the front unit
Turn off the instrument and disconnect from the mains.
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the 4 screws from the front handles (410), left and right, and take off the front handles.
Remove the countersunk screw (390) next to the display and pull off the front cover (300, 303, 306,
310, 313, 316) forwards
Remove the 2 countersunk screws (610) in the top of the front frame and the 2 in the bottom.
ZVA8: Remove the countersunk screws (168) (2 ), (153), (154), (163), (164)
Pull out the front unit together with the keyboard and display (600, 604) forwards.
The cables to the front module controller are still connected.
Disconnect the cables to the LCD, the DC/AC illumination converter, the key pad (keyboard), the
tachogenerator and, if necessary, the network connection on the front module controller.
N.B.:
When disconnecting cables, be especially careful with the cable to the keyboard. It is a foil
cable and can only be removed when the locking device on the foil-cable connector is
released.
Removing the front module controller
Remove the 10 sems screws (590) in the front module controller and remove the front module
controller in the following way (see Fig. 3-1):
Note:
The insertion force for the front module controller on the motherboard is very large.
The slot in the bottom of the controller tray is provided to facilitate pushing out the front
module controller forwards.
Using a blunt, flat tool, carefully edge the board forwards.
Do not insert the tool too far into the slot; only apply pressure to the board.
To ease the board out, apply light pressure to each and every
Do not bend the board.
1145.1155.82
3.23
slot.
E-5
Board Replacement
Fig. 3-1
R&S ZVA
Removing the front module controller Installing the new front module controller and putting
the instrument back together.
Carefully insert the new front module controller on the motherboard and screw into place with 10
sems screws (590).
Caution:
With type FMR6 1091.2520.00, there is a danger of shorting between board components,
tracks and screws (590). Use suitable insulation.
Reconnect the cables to the front module controller, ensuring correct polarity.
Front Module Controller Typ FMR6
Connector for rotary pulse generator
Controller module
Controller module
Contact side of switching foil (keyboard) up
CPU
Battery
LAN 1 LAN 2
+
Connector for display and
converter adapter board
Fig. 3-2
Location of the edge connectors on the front module controller
Re-insert the front unit into the instrument and secure to the front frame with 4 countersunk screws.
(610).
Fit the following countersunk screws (168) (2 ), (153), (154), (163), (164).
Avoid trapping cables and ensure cabling is tidy..
Replace the front cover (300 to 316) and secure with the countersunk screw (390).
Secure the 2 front handles (410) with the 4 screws.
Fit the termination and the 3.5mm connection cables (only with option ZVAx-B16)
1145.1155.82
3.24
E-5
R&S ZVA
Board Replacement
Putting into operation
Connect the mains cable and turn on at the power on switch. The instrument is now in standby
mode.
Prepare a BIOS disk downloading the required file from https://gloris.rohdeschwarz.com
(Document link: Firm- \ Software) on a floppy disk.
Insert the BIOS disk into the floppy disk drive.
Turn on the instrument and wait for the first beep. Press the DEL key. The instrument should now
display the setup menu.
•
•
•
•
•
•
Select Advanced BIOS Features
Enter
Select First Boot Device
Select Floppy using page up/down key
Press F10 key (save)
Enter
BIOS has now been programmed.
Do not turn the instrument off when the program is running.
Follow the instructions on the screen.
Select Service Level 2 (see Service Functions).
Check the protocol file for errors:
[ INFO : Error Log ]
1145.1155.82
3.25
E-5
Board Replacement
R&S ZVA
Replacing the Lithium Battery on the Front Module Controller
(See Chapter 5, Spare Parts List, Item (582), and drawings 1145.1110, 1145.1290)
The lithium battery is located on the front module controller behind the front unit.
Danger of fire or intoxication
Lithium batteries must not be exposed to high temperatures or fire.
Keep away from children to avoid intoxication.
If the battery is replaced improperly, there is danger of explosion. Only replace the battery with R&S type (See Chapter 5, Spare Parts List, Item 776 for type FMR6).
Lithium batteries are hazardous waste and must be disposed of in dedicated containers. Observe local regulations regarding waste disposal.
Do not short-circuit the battery!
Opening the instrument and removing the front unit
Turn off the instrument and disconnect from the mains.
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the 4 screws from the front handles (410), left and right, and take off the front handles.
Remove the countersunk screw (390) next to the display and pull off the front cover (300, 303, 306,
310, 313, 316) forwards
Remove the 2 countersunk screws (610) in the top of the front frame and the 2 in the bottom.
ZVA8: Remove the countersunk screws (168) (2 ), (153), (154), (163), (164)
Pull out the front unit together with the keyboard and display (600, 604) forwards.
Risk of instrument damage
Be careful when removing the front panel of the instrument because the connecting
cables are still connected to the controller to avoid damage to the instrument.
1145.1155.82
3.26
E-5
R&S ZVA
Board Replacement
Disconnecting cables
When pulling off the connecting cables be careful with the cable connecting to the
keyboard. It is a film cable which can only be disconnected after sliding up the lock of
the film cable plug.
Disconnect the cables to the LCD, the DC/AC illumination converter, the key pad (keyboard), the
tachogenerator and, if necessary, the network connection on the front module controller.
Note:
1145.1155.82
When disconnecting cables, be especially careful with the cable to the keyboard. It is a
foil cable and can only be removed when the locking device on the foil-cable connector
is released.
3.27
E-5
Board Replacement
R&S ZVA
Removing the lithium battery
Carefully lift up and pull out the battery.
Note:
Lithium battery 3.4 V (dia. 20 mm * 3 mm) R&S Item No. 0858.2049.00
Front Module Controller Typ FMR6
Connector for rotary pulse generator
Controller module
Controller module
Contact side of switching foil (keyboard) up
CPU
Battery
LAN 1 LAN 2
+
Connector for display and
converter adapter board
Fig. 3-3
Location of the lithium battery on the front module controller
Installing the new battery and reassembling the instrument
Risk of discharge
Do not short-curcuit the battery.
Insert the battery under the spring in the holder.
N.B.: The positive pole of the battery (+) must be uppermost.
Reinsert the front unit in the instrument and secure to the front frame with 4 countersunk screws
(610).
Refit the countersunk screws (168) (2 ), (153), (154), (163), (164).
Risk of instrument damage
Be careful when replacing the cables. Connect the cables to the proper connectors to
avoid damage to the instrument.
Replace the front cover (300, 303, 306, 310, 313, 316) and screw in the countersunk screw (390).
Refit the 2 front handles (410) using 4 screws.
Fit the termination and the 3.5mm connection cables (only with option ZVAx-B16).
1145.1155.82
3.28
E-5
R&S ZVA
Board Replacement
Putting into operation
Connect the mains cable, turn on at the power switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
1145.1155.82
3.29
E-5
Board Replacement
R&S ZVA
Replacing Hard Disk A60
(See Chapter 5, Spare Parts List, Item 710, and drawings 1145.1110 and 1145.1310)
The hard disk is located between the controller tray and the boards. The spare disk is delivered with the
software pre-installed.
Before removal:
Whenever possible, back up the user data on an external data storage medium.
Opening the instrument and replacing the hard disk
Turn off the instrument, disconnect from the mains, unscrew the 4 rear-panel feet (460) and pull off the
enclosure (400) backwards
Lift off the instrument cover (296) at the top after undoing the countersunk screws (298).
Disconnect the flat cable (715) at the hard disk drive.
Note: Do not pull or push on the flat cable – instead, carefully lever out the connector strip with a
small screwdriver.
Remove the 2 countersunk screws (725) in the hard disk holder (720).
Remove the hard disk (710) and holder (720).
Undo the 4 countersunk screws (730), remove the old hard disk and screw the new hard disk to the
holder (720).
Installing and putting the new hard disk into operation
Refit the hard disk and holder into the instrument using 2 countersunk screws (725).
Note: The bottom of the holder is inserted into a sheet-metal wall.
Connect the flat cable (715) to the hard disk.
Replace the instrument’s top cover (296) and screw back into position with 23 or 28 countersunk
screws (298).
Slide on the enclosure (400) and screw the 4 rear-panel feet (460) back into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Function)
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Perform the factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.30
E-5
R&S ZVA
Board Replacement
Replacing LCD A70 and the DC/AC Converter
(See Chapter 5, Spare Parts List Items 910, 930 and drawings 1145.1110, 1145.1390)
The LCD and the associated DC/AC converter are accommodated on a mounting plate. The connection
to the front module controller is made with cables which should also be replaced individually. The
replacement procedure is as follows:
Opening the instrument and removing the front unit
Turn off the instrument and disconnect from the mains.
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the 4 screws from the front handles (410), left and right, and take off the front handles.
Remove the countersunk screw (390) next to the display and pull off the front cover (300, 303, 306,
310, 313, 316) forwards
Remove the 2 countersunk screws (610) in the top of the front frame and the 2 in the bottom.
ZVA8: Remove the countersunk screws (168) (2 ), (153), (154), (163), (164)
Pull out the front unit together with the keyboard and display (600, 604) forwards.
The cables to the front module controller are still connected
Disconnect the cables to the LCD, the DC/AC illumination converter, the key pad (keyboard), the
tachogenerator and, if necessary, the network connection to the front module controller.
Note:
When disconnecting cables, be especially careful with the cable to the keyboard. It is a
foil cable and can only be removed when the locking device on the foil-cable connector
has been released.
Place the key-side of the front unit on a clean surface.
Removing the DC/AC converter
Disconnect the cable from the display (910) to the DC/AC converter (930).
Disconnect the converter cable (950) to the DC/AC converter (930)
Remove the DC/AC converter (930) by undoing the 2 screws (940)
Removing the LCD
Disconnect the display cable (945) by cutting through the adhesive label(946).
Remove the display connector (1020) after you have undone the two screws (1040).
Disconnect the display cable (1030) at the display (910).
Remove the display (910) after removing the 4 screws (920)
1145.1155.82
3.31
E-5
Board Replacement
R&S ZVA
Installing and putting into operation a new LCD or DC/AC converter
Reinstall the new LCD or new DC/AC converter by reversing the disassembly procedure, refit all
screws and reconnect the cables that have been disconnected (drawing 1145.1390).
When replacing the display (921) or display cable (945), use a new adhesive label (946) to secure
the cabling.
Place the key-side of the front unit on the top of the instrument so that the cables can be connected
to the front module controller.
Carefully connect all cable connectors to the front module controller, ensuring that the polarity is
correct.
Front Module Controller Typ FMR6
Connector for rotary pulse generator
Controller module
Controller module
Contact side of switching foil (keyboard) up
CPU
Battery
LAN 1 LAN 2
+
Connector for display and
converter adapter board
Fig. 3-4
Location of the edge contacts on the front module controller
Reinsert the front unit in the instrument and secure to the front frame with 4 countersunk screws
(610).
Refit the countersunk screws (168) (2 ), (153), (154), (163), (164).
Avoid trapping cables and ensure cabling is tidy.
Replace the front cover (300, 303, 306, 310, 313, 316) and secure with countersunk screw (390).
Refit the 2 front handles (410) using the 4 screws.
Fit the termination and the 3.5mm connection cables (only with option ZVAx-B16).
Connect the mains cable, turn on at the mains switch and press the ON key.
1145.1155.82
3.32
E-5
R&S ZVA
Board Replacement
Replacing Flexible switch board (Keyboard) A16 / Key Pad A15
(See Chapter 5, Spare Parts List, Items 860, 870 and drawings 1145.1110, 1145.1390)
The flexible switch board (keyboard) and key pad are located behind the front cover and the keyboard
frame
Opening the instrument and removing the front unit
Turn off the instrument and disconnect from the mains.
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the 4 screws from the front handles (410), left and right, and take off the front handles.
Remove the countersunk screw (390) next to the display and pull off the front cover (300, 303, 306,
310, 313, 316) forwards
Remove the 2 countersunk screws (610) in the top of the front frame and the 2 in the bottom.
ZVA8: Remove the countersunk screws (168) (2 ), (153), (154), (163), (164)
Pull out the front unit together with the keyboard and display (600, 604) forwards and place it with
the key-side on top of the instrument.
The cables to the front module controller are still connected.
Disconnect the cables to the LCD, the DC/AC illumination converter, the key pad (keyboard), the
tachogenerator and, if necessary, the network connection to the front module controller.
Note:
When disconnecting cables, be especially careful with the cable to the keyboard. It is a
foil cable and can only be removed when the locking device on the foil-cable connector
is released.
Removing the flexible switch board (keyboard) / key pad
Place the front unit with the key-side upwards on a clean surface.
Remove knob (990) from the tachogenerator.
Undo the 10 countersunk screws (890) and remove the keyboard frame (800, 805).
The flexible switch board (860) and the key pad (870) can now be replaced.
Installing a new flexible switch board / key pad and reassembling the instrument
Insert the new flexible switch board (860) into the keyboard frame (800, 805) from behind.
N.B.:
The positioning pins must be inserted in the holes in the keyboard frame.
Place the new key pad (870) on the rear of the flexible switch board (860).
1145.1155.82
3.33
E-5
Board Replacement
Note:
R&S ZVA
Thread the foil cable’s connector through the slot in the mounting tray.
Position the key pad so that the pins on the flexible switch board pass through the holes
in the key pad.
Place the rear of the display unit on the key pad (870).
N.B.:
Position the display unit so that the pins on the flexible switch board pass through the
holes in the mounting tray.
Press the front unit together, with the key-side upwards turn and screw back together again with 10
countersunkl screws (890).
Place the front unit with the key-side on top of the instrument so that the cables can be connected to the
front module controller
Reconnect the cables to the front module controller, ensuring correct polarity.
Front Module Controller Typ FMR6
Connector for rotary pulse generator
Controller module
Controller module
Contact side of switching foil (keyboard) up
CPU
Battery
LAN 1 LAN 2
+
Connector for display and
converter adapter board
Fig. 3-5
Location of the edge contacts on the front module controller
Reinsert the front unit into the instrument and secure to the front frame with 4 countersunk screws
(610).
Refit the countersunk screws (168) (2 ), (153), (154), (163), (164).
Avoid trapping cables and ensure cabling is tidy..
Replace the front cover (300, 303, 306, 310, 313, 316) and secure with the countersunk screw
(390).
Refit the 2 front handles (410) using 4 screws.
Fit the termination and the 3.5mm connection cables (only with option ZVAx-B16).
Connect the mains cable, turn on at the mains switch and press the ON key.
1145.1155.82
3.34
E-5
R&S ZVA
Board Replacement
Replacing the Front Cover
(See Chapter 5, Spare Parts List, Items 300, 303, 306, 310, 313, 316 and drawing 1145.1110)
The front cover is the outermost front panel with lettering. Each instrument type has its own front cover.
Turn off the instrument and disconnect from the mains.
Remove the 4 screws in the front handles (410), right and left, and take off the front handles
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the countersunk screw (390) next to the display and pull off the front cover (e.g. 300)
forwards
Fit the new front cover and reassemble the instrument by reversing the disassembly procedure.
Connect the mains cable, turn on at the mains switch and press the ON key.
1145.1155.82
3.35
E-5
Board Replacement
R&S ZVA
Replacing Disk Drive A30
(See Chapter 5, Spare Parts List, Item 670 and drawings 1145.1110 and 1145.1310)
Opening the instrument and removing the disk drive
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and pull
off the enclosure (400) backwards.
Remove the 2 sems screws (700) and carefully lift out the floppy disk drive (670), together with the
floppy drive holder (680).
N.B.: The floppy cable to the motherboard is still connected.
Disconnect floppy cable (690) on the floppy disk drive.
Installing a new disk drive and reassembling the instrument
Release the floppy disk drive by removing the 3 sems screws (700) from the floppy drive holder
(680) and insert a new floppy disk drive (670) into the floppy drive holder (680).
Connect floppy cable (690) on the floppy disk drive.
Resecure the floppy disk drive (680) from above to the side of the instrument with the fan using 2
sems screws (700).
N.N.: Center the floppy disk drive wrt the cut-out in the front cover.
Slide the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Function test
The instrument boots up and starts the instrument firmware.
Insert a 3 ½ disk with files.
Press the FILE key, then the File Manager softkey and Edit Path.
Enter “ a “ and “ : “ with the screen functions and terminate with the Enter key.
The directory structure of the disk displayed on the screen shows that the floppy disk drive is
operating properly.
1145.1155.82
3.36
E-5
R&S ZVA
Board Replacement
Replacing USB Board A40
(See Chapter 5, Spare Parts List, Item 1050 and drawings 1145.1110 and 1145.1390)
The USB board is located behind the front cover and the keyboard frame next to the ON key.
Opening the instrument and removing the USB-board
Turn off the instrument and disconnect from the mains.
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the 4 screws from the front handles (410), left and right, and take off the front handles.
Remove the countersunk screw (390) next to the display and pull off the front cover (300, 303, 306,
310, 313, 316) forwards
Remove the 2 countersunk screws (610) in the top of the front frame and the 2 in the bottom.
ZVA8: Remove the countersunk screws (168) (2 ), (153), (154), (163), (164).
Pull out the front unit together with the keyboard and display (600, 604) forwards and place it with the
key-side on top of the instrument.
Remove the 2 screws (1070), disconnect the cable and remove the USB board (1050).
Fitting the USB board and reassembling the instrument
Install the new USB board by reversing the removal procedure, replace all screws and connect and
install the relevant cables (drawing 1145.1390).
Insert the front unit back into the instrument and secure to the front frame with 4 countersunk
screws (610).
Refit the countersunk screws (168) (2 ), (153), (154), (163), (164).
Replace the front cover (300, 303, 306, 310, 313, 316) and secure with the countersunk screw
(390).
Refit the 2 front handles (410) using 4 screws.
Fit the termination and the 3.5mm connection cables (only with option ZVAx-B16).
Connect the mains cable, turn on at the mains switch and press the ON key.
Check the USB board: Connect the mouse or keyboard and perform a function check.
1145.1155.82
3.37
E-5
Board Replacement
R&S ZVA
Replacing Power Supply A20
(See Chapter 5, Spare Parts List, Items 790 and drawings 1145.1110, 1145.1290, 1145.1310)
The power supply is installed at the rear of the instrument frame.
Removing the power supply
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) towards the rear.
Remove the 4 screws (792) in the rear panel.
Pull out the power supply unit a little at the rear of the instrument, remove screw (737) and antitouch guard (736).
On the left-hand side of the power supply, pull off the protective conductor cable and fuse board
(735) to the left.
On the right-hand side of the power supply, remove the plug-on connections to the motherboard.
Remove the power supply unit.
Installing the new power supply
Fit the new power supply by reversing the removal procedure
If you refit a power supply 1145.5238, fit the cables from the removed one to the new one (see
drawing 1145.1290)
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors
[ INFO : Error Log ]
1145.1155.82
3.38
E-5
R&S ZVA
Board Replacement
Replacing Fuse board A21
(See Chapter 5, Spare Parts List, Item 735, and drawings 1145.1110, 1145.1290)
The fuse board is installed on the left-hand side of the power supply.
Removing the power supply and the fuse board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the 4 screws (757) in the rear panel.
Pull out the power supply unit a little at the rear of the instrument, remove screw (737) and antitouch guard (736).
On the left-hand side of the power supply, pull off the fuse board (735) to the left.
Disconnect the two mains cables from the fuse board.
Fitting the new fuse board and the power supply
Connect the mains cables to the fuse board and refit the fuse board to the power supply.
Secure the anti-touch guard (736) with screw (737).
Reinstall the power supply by reversing the removal procedure.
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors
[ INFO : Error Log ]
1145.1155.82
3.39
E-5
Board Replacement
R&S ZVA
Replacing a Fan
(See Chapter 5, Spare Parts List, Item 15 and drawings 1145.1110, 1145.1310)
The fans, three in all, are located behind the right-hand side panel.
Opening the instrument and removing the fan
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and pull
off the enclosure (400) backwards.
Lift off the top instrument cover (296) after undoing the countersunk screws (298).
For replacing the fan located near by the front remove the 2 sems screws (700) and carefully lift out
the floppy disk drive (670), together with the floppy disk holder (680).
Disconnect the fan cable on the motherboard.
Remove fan (15) by undoing the 4 fan screws (16).
Fitting a new fan and reassembling the instrument
Install the fan using the 4 fan screws.
N.B.:The arrows on the fan show the installation position. The fan blows air into the instrument.
Route the fan cable so that it cannot get caught in the fan.
Connect the fan cabling on the motherboard X35, X36 and X37 (FAN).
Refit the top instrument cover (296) with countersunk screws (298).
Connect the mains cable, turn on at the mains switch and press the ON key.
Check that all three fans are operating correctly (fans are blowing air into the instrument).
Turn off the instrument and disconnect the mains cabling again.
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
1145.1155.82
3.40
E-5
R&S ZVA
Board Replacement
Replacing Motherboard A10
(See Chapter 5, Spare Parts List, Item 510 and drawings 1145.1110, 1145.1310)
The motherboard is located on the base of the instrument.
N.B.:
The motherboard can only be replaced at R&S service centers.
Opening the instrument and removing the motherboard
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Lift off the top instrument cover (296) after undoing the countersunk screws (298).
Extract the top boards: Use ejector lever for the synthesizer and network controller, hold the
frequency reference by the enclosure.
Remove the power supply (550).
•
Remove the 4 screws (757) in the rear panel.
•
Pull out the power supply unit a little at the rear of the instrument, remove screw (737) and antitouch guard (736).
•
On the left-hand side of the power supply, pull off the protective conductor cable and the fuse
board (735) to the left.
•
On the right-hand side of the power supply, pull off the plug-in connections to the motherboard.
•
Remove the power supply unit.
Remove the 4 screws in the front handles (410), right and left, and take off the front handles.
Remove the countersunk screw (390) next to the display and pull off the front cover (300, 303, 306,
310, 313, 316) forwards.
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the 2 countersunk screws (610) in the top of the front frame and the 2 in the bottom.
Remove the countersunk screws (168) (2 ), (153), (154), (163), (164).
Pull out the front unit together with the keyboard and display (600, 604) forwards.
The cables to the front module controller are still connected.
Disconnect the cables to the LCD, the DC/AC illumination converter, the key pad (keyboard), the
tachogenerator and, if necessary, the network connection to the front module controller.
Note:
When disconnecting cables, be especially careful with the cable to the keyboard. It is a
foil cable and can only be removed when the locking device on the foil-cable connector
is released.
Remove the front module controller (for instructions see “Replacing Front Module Controller A90“)
1145.1155.82
3.41
E-5
Board Replacement
R&S ZVA
Place the instrument on its top and remove the instrument’s base cover (297) by undoing the
screws (299).
Undo the RF cabling from the reflectometers (165, 170, 175) to the LO divider (125) and to the
motherboard.
Release the 50-pin flat cable and disconnect from the reflectometers
Remove screws (151, 156, 161) and take out the reflectometers.
Undo RF cabling at the LO divider (125).
Disconnect the 12-pin flat cable from the LO divider
Remove screws (127) (2 in the strut, 4 in the rear panel) and take out the LO divider together with
plate (126)
Undo the screws holding the connectors on the rear panel:
• The 6 hexagonal nuts and washers for the BNC connectors.
• 2 hexagonal bolts (530, 540) each for the monitor interface and the user-control interface.
• 2 hexagonal screws (550) each for the USB interface and in the dummy panel (555).
Remove the 3 screws (144) each for the left and right side panels and the 2 screws (143) in the
center and take out both motherboard rails (140, 141).
Disconnect any cabling still on the motherboard (fan, floppy, IEC-bus, etc.).
Remove the 14 screws holding the motherboard (520) and take out the motherboard.
Remove the RF and IF cables using the tool 11W 101-000 (Rosenberger).
1145.1155.82
3.42
E-5
R&S ZVA
Board Replacement
Installing the motherboard and reassembling the instrument
N.B.:
The motherboard is the passport of the instrument and unique for every unit.
The Eprom on the motherboard contains the serial No. of the instrument.
Pre-configured motherboards are not available.
Install the new motherboard by reversing the removal procedure.
N.B.:
Install the motherboard carefully to prevent any damage to components.
Lettering indicates where cables are to be connected.
Reinstall the front module controller, front unit, power supply, boards and cables, instrument covers,
enclosure and rear-panel feet by reversing the disassembly procedure.
Connect the mains cable, turn on at the mains switch and press the ON key.
For writing motherboard data to the EPROM please contact the service center in Munich.
Select Service Level 2 (see Service Functions).
Check the protocol file for errors: [ INFO : Error Log ]
Align the DC inputs (see Aligning the DC Inputs in chapter 2)
Write synthesizer mapping and shift data to the motherboard EPROM (see Correction Value
Recording in chapter 2)
1145.1155.82
3.43
E-5
Board Replacement
R&S ZVA
Replacing a Reflectometer RM8 A510 to 540
(See Chapter 5, Spare Parts List, Items 150, 160 and drawing 1145.1110)
The boards are located under the motherboard.
Opening the instrument and removing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the bottom instrument cover (297) after undoing the screws (299).
Remove termination and 3.5mm connection cables (only with option ZVAx-B16)
Remove the screws (153), (154), (163), (164) in the front of the instrument next to the port
connector and (168) in case of port 4.
Disconnect the source cable, the LO cable, the two IF cables and the 50-pin control cable from the
reflectometer.
Remove the 2 screws (151, 161) at the end of the reflectometer and take out the reflectometer
Installing the board and reassembling the instrument
Insert the new board into the instrument and reconnect any cables that have been disconnected
N.B.: Use the lettering on the motherboard as an aid.
Screw in the screws (153, 154, 163, 164, 168) in the front of the instrument.
Screw in the 2 screws (151, 161) in the end of the reflectometer.
Fit the instrument base cover (297) and secure with screws (299).
Slide the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Recording Correction Values in chapter
2).
Perform the factory system error calibration (see Factory System Error Calibration in chapter 2).
1145.1155.82
3.44
E-5
R&S ZVA
Board Replacement
Replacing Generator Board (ZVA8 only)
(See Chapter 5, Spare Parts List, Item 110 and drawing 1302.4960.08)
Opening the instrument and removing the board
Remove the reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Remove the cover (130)
Remove the fan cable
Pull off the generator board (110)
Installing the board and reassembling the instrument
Fit the new generator board (110)
Reconnect the fan cable
Fit the cover (130)
Reinstall the reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Recording Correction Values in chapter
2).
Perform the factory system error calibration (see Factory System Error Calibration in chapter 2).
1145.1155.82
3.45
E-5
Board Replacement
R&S ZVA
Replacing Receiver Board (ZVA8 only)
(See Chapter 5, Spare Parts List, Item 120, 125 and drawing 1302.4960.08)
Opening the instrument and removing the board
Remove the reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Remove the cover (150)
Pull off the receiver board (120, 125)
Installing the board and reassembling the instrument
Fit the new receiver board (120, 125)
Fit the cover (150)
Reinstall the reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Recording Correction Values in chapter
2).
Perform the factory system error calibration (see Factory System Error Calibration in chapter 2).
1145.1155.82
3.46
E-5
R&S ZVA
Board Replacement
Replacing Generator and Receiver Cover (ZVA8
only)
(See Service Circular 10028 and Chapter 5, Spare Parts List, Items 130, 150 and drawing
1302.4960.08)
Opening the instrument and removing the cover
Remove the reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Remove the RM mount (200), 4 screws (210)
Remove the covers (130, 150)
Installing the cover and reassembling the instrument
Fit the new covers (130, 150)
Refit the RM mount (200)
Reinstall the reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the receiver correction data (see Recording Correction Values in chapter 2).
Perform the factory system error calibration (see Factory System Error Calibration in chapter 2).
1145.1155.82
3.47
E-5
Board Replacement
R&S ZVA
Replacing the Inner Conductor of a Port Connector (ZVA8
only)
(See Chapter 5, Spare Parts List, Item 110, and drawings 1145.1110, 1145.4177, 1145.3593)
Opening the instrument and removing the reflectometer
Remove the Reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Replacing the inner conductor
Unscrew the N outer conductor with a spanner (narrow, SW 14mm) and take out inner conductor
unit.
N.B.: Ensure that the centring disk (135) is also removed.
Carefully insert the new inner conductor in the bridge unit enclosure and screw back the N outerconductor (lock with Loctite 262, mount with torque 3.5 Nm).
Reassembling the instrument
Reinstall the Reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Check the gauge (see Checking the Gauge in chapter 2)
Perform factory system error calibration (see Factory System Error Calibration in chapter 2).
1145.1155.82
3.48
E-5
R&S ZVA
Board Replacement
Replacing the Bridge Unit (ZVA8 only)
(See Chapter 5, Spare Parts List, drawings 1145.1110, 1145.4177, Item 100)
Opening the instrument and removing the reflectometer
Remove the Reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Removing the bridge unit
Loosen the MEAS, REF and GEN cables (310, 320, 300) at both ends and disconnect at the bridge
unit.
N.B.: When loosening support the cable with a 7mm spanner!
Remove the 3 screws (160) and carefully pull the bridge unit off the reflectometer.
Remove the 2 screws (240) and remove the plate (230).
Fitting the new bridge unit
Secure plate (230) to the new bridge unit using the 2 screws (240).
Carefully place the bridge unit on the reflectometer and secure with 3 screws (160).
Screw the MEAS- REF and GEN cables (310, 320, 300) to the bridge unit, and then tighten at both
ends.
N.B.: When tightening with a 7 mm spanner support the cable.
Reassembling the instrument
Reinstall the Reflectometer (see chapter Replacing Reflectometer Board A510 to A540)
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
Check the gauge (see Checking the Gauge in chapter 2)
Record generator and receiver correction data (see Recording Correction Data).
Perform factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.49
E-5
Board Replacement
R&S ZVA
Replacing a Reflectometer RM24 A510 to 540
(See Chapter 5, Spare Parts List, Items 180, 190, 200 and drawings 1145.1110, 1145.4283)
Opening the instrument and removing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the bottom instrument cover (297) after undoing the 12 countersunk screws (299).
Remove 3.5mm connection cables (only with option ZVA24-B16)
Disconnect the three cables to the coupler, the LO cable, the two IF cables and the 50-pin control
cable from the reflectometer.
Loosen the captive screws (see 1145.1110.01 sheet 4 / 5) and take out the reflectometer.
Installing the board and reassembling the instrument
Insert the new board into the instrument.
Screw in the captive screws.
Reconnect any cables that have been disconnected.
Fit the 3.5mm connection cables (only with option ZVA24-B16).
Fit the instrument base cover (297) and secure with screws (299).
Slide the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Recording Correction Values).
Perform the factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.50
E-5
R&S ZVA
Board Replacement
Replacing a Reflectometer RM40 and RM50 A510 to 540
(See Chapter 5, Spare Parts List, Items 209, 222, 230, 232 and drawings 1145.1110, 1145.4319,
1305.3413)
The boards are located under the motherboard.
Opening the instrument and removing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the bottom instrument cover (297) after undoing the 12 countersunk screws (299).
Disconnect the three cables to the coupler, the LO cable, the two IF cables and the 50-pin control
cable from the reflectometer.
Loosen the captive screws (see 1145.4319, 1305.3413) and take out the reflectometer.
Installing the board and reassembling the instrument
Insert the new board into the instrument.
Screw in the captive screws.
Reconnect any cables that have been disconnected.
Fit the instrument base cover (297) and secure with screws (299).
Slide the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Recording Correction Values).
Perform the factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.51
E-5
Board Replacement
R&S ZVA
Replacing a Reflectometer RM67 A510 to 540
(See Chapter 5, Spare Parts List, Items 300 and 350 and drawing 1305.7002)
The boards are located under the motherboard.
Opening the instrument and removing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the bottom instrument cover (297) after undoing the 12 countersunk screws (299).
Disconnect the three cables to the coupler, the LO cable, the two IF cables and the 50-pin control
cable from the reflectometer.
Loosen the captive screws (see1305.7002) and take out the reflectometer.
Installing the board and reassembling the instrument
Insert the new board into the instrument.
Screw in the captive screws.
Reconnect any cables that have been disconnected.
Fit the instrument base cover (297) and secure with screws (299).
Slide the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Recording Correction Values).
Perform the factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.52
E-5
R&S ZVA
Board Replacement
Replacing the Coupler Unit (ZVA24, ZVA40, ZVA50)
(See Chapter 5, Spare Parts List, item 230 and drawing 1145.1110)
Opening the instrument and removing the coupler
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the instrument base cover (297) after undoing the screws (299).
Disconnect the 3 RF cables and the bias cable from the coupler
Remove the 3.5mm connection cables (only with option ZVA24-B16).
Remove the frontcover
Remove the screws (182, 186, 202, 206) in the front of the instrument next to the port connector
and take out the coupler.
Fitting the new coupler unit and reassembling the instrument
Insert the coupler into the instrument and screw in the 4 screws (181, 186, 220).
Reconnect the 3 RF cables and the bias cable.
Fit the 3.5mm connection cables (only with option ZVA24-B16).
Fit the instrument base cover (297) and secure with 12 countersunk screws (299).
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record generator and receiver correction data (see Recording Correction Data).
Perform factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.53
E-5
Board Replacement
R&S ZVA
Replacing the Coupler Unit (ZVA67)
(See Chapter 5, Spare Parts List, item 245 and drawings 1305.7002 and 1305.6241)
Opening the instrument and removing the coupler
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the instrument base cover (297) after undoing the screws (299).
Disconnect the 3 RF cables and the bias cable from the coupler
Remove the 3.5mm connection cables (only with option ZVA24-B16).
Remove the frontcover
Remove the screws (182, 186, 202, 206) in the front of the instrument next to the port connector
and take out the coupler.
Fitting the new coupler unit and reassembling the instrument
Insert the coupler into the instrument and screw in the 4 screws (181, 186, 220).
Reconnect the 3 RF cables and the bias cable.
Fit the 3.5mm connection cables (only with option ZVA24-B16).
Fit the instrument base cover (297) and secure with 12 countersunk screws (299).
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record generator and receiver correction data (see Recording Correction Data).
Perform factory system error calibration (see Factory System Error Calibration).
Replacing the Test Set (ZVA40 only)
N.B.:
In case of defective Test Set please contact the Central Service in Munich.
1145.1155.82
3.54
E-5
R&S ZVA
Board Replacement
Replacing the Reflectometer Fan
(See Chapter 5, Spare Parts List, Item 100, 190 and drawings 1145.1110, 1145.4177, 1145.4283,
1302.5621)
ZVA8 and ZVA24 only:
Remove the reflectometer (see chapter Replacing a Reflectometer RMxx A510 to A540)
Replacing the fan
Disconnect the fan cable at the reflectometer.
Undo the 4 holding screws (110,194) and remove the fan.
Insert the new fan (ZVA8: cable outlet to the outside, ZVA24: cable outlet to the inside).
Screw back the 4 screws (110, 194) and washers (120, 130, 192, 193).
Reassembling the instrument
Reinstall the reflectometer (see chapter Replacing a Reflectometer RMxx A510 to A540)
Connect the mains cable, turn on at the mains switch and press the ON key.
Check that the fan is operating.
Turn off the instrument again and disconnect from the mains.
Fit the instrument base cover (297) and secure with 12 countersunk screws (299).
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Reconnect the mains cable, turn on at the mains switch. The instrument is now in the standby
mode.
ZVA40, ZVA50 and ZVA67 only:
Remove the cover plate (260) undoing 12 screws (261) and 4 screws (212)
Remove blower attachement (210) undoing 2 screws (211)
Replacing the fan
Disconnect the fan cable at the reflectometer.
Remove the fan.
Insert the new fan (cable outlet to the inside of the instrument) and cut the rubber pins (see
1302.5621).
Connect the fan cable to the reflectometer and reinstall the blower attachement (210).
1145.1155.82
3.55
E-5
Board Replacement
R&S ZVA
Reassembling the instrument
Reinstall the cover plate (260)
Connect the mains cable, turn on at the mains switch and press the ON key.
Check that the fan is operating.
Turn off the instrument again and disconnect from the mains.
Fit the instrument base cover (297) and secure with 12 countersunk screws (299).
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Reconnect the mains cable, turn on at the mains switch. The instrument is now in the standby
mode.
1145.1155.82
3.56
E-5
R&S ZVA
Board Replacement
Replacing Network Controller Board A130, A140
(See Chapter 5, Spare Parts List, Items 100, 105 and drawing 1145.1010)
The board is in the upper section of the instrument.
Opening the instrument and removing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Lift off the instrument top cover (296) after undoing the screws (298).
Extract the network controller using the ejector lever
Fitting the board and reassembling the instrument
Fit the new board in the instrument.
Refit the top instrument cover (296) with screws (298).
Slide the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the receiver correction data (see Recording Correction Values).
Perform factory system error calibration (see Factory System Error Calibration).
Align the DC inputs (see Aligning the DC Inputs).
1145.1155.82
3.57
E-5
Board Replacement
R&S ZVA
Replacing Synthesizer Board A150, A160
(See Chapter 5, Spare Parts List, Items 110, 112, 113, 115 and drawing 1145.1110)
The board is located in the upper section of the instrument.
N.B.:
Synthesizers with part numbers 1145.xxxx or 1300.xxxx are no longer available. In case of
defect please contact the Central Service in Munich.
Opening the instrument and removing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Lift off the instrument top cover (296) after undoing the screws (298).
Extract the synthesizer with the ejector lever.
Installing the board and reassembling the instrument
Insert the new board into the instrument.
Refit the instrument top cover (296) securing with the screws (298).
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Install firmware update, if necessary (version U 1.78).
Install synthesizer mapping (see Correction Value Recording)
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
Record the generator and receiver correction data (see Correction Value Recording).
Perform factory system error calibration (see Factory System Error Calibration).
1145.1155.82
3.58
E-5
R&S ZVA
Board Replacement
Replacing Frequency Reference Board A100
(See Chapter 5, Spare Parts List, Item 120 and drawings 1145.1110, 1164.1770)
Opening the instrument and replacing the board
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Lift off the instrument top cover (296) after undoing the screws (298).
Extract the frequency reference board (120).
Installing the board and reassembling the instrument
Insert the new board into the instrument
Refit the instrument top cover (296) with the screws (298).
Push the enclosure (400) back on and screw the 4 rear-panel feet (460) into position.
Connect the mains cable, turn on at the mains switch and press the ON key.
Select Service Level 2 (see Service Functions).
When the instrument has been started, check the protocol file for errors:
[ INFO : Error Log ]
1145.1155.82
3.59
E-5
Troubleshooting
R&S ZVA
Troubleshooting
The instructions in this manual describe troubleshooting down to the board level. Any defective boards
can then be replaced and the instrument put back into operation. A selftest which checks the board
diagnostic voltages and displays limit violations is provided to facilitate troubleshooting and diagnosis.
We recommend that you return your instrument to the technical specialists at an R&S service facility for
board replacement and any further repairs that may be needed (see the address list at the beginning of
this manual).
Risk of damage to the boards
Be careful not to cause short circuits when measuring voltages at pins placed close
together!
Do not plug or unplug boards prior to disconnecting them from the AC supply.
The R&S ZVA has the following facilities to simplify diagnosis:
• Selftest
• Service functions
The first thing to do if you encounter any problems is to check if any connection
(cables, edge connectors etc.) are damaged or even incorrectly inserted.
1145.1155.82
3.60
E-5
R&S ZVA
Troubleshooting
Test Equipment and Accessories
Item.
Instrument type
Recommended features
1
DC meter
2
Power supply
0 to 10 V
3
Spectrum analyzer
Frequency range 0 to 40 GHz
Recommende
d model
R&S Order
No.
R&S URE
0350.5315.02 1
R&S FSU 40
Qty.
1
(R&S FSU 50)
(R&S FSU 67)
1
4
Power meter
(if FSU50 or FSU67
not available)
4
Power sensor
10 MHz to 67 GHz
R&S NRP-Z57
5
Test cable
0.6 m long
K male to K female
-
5
Test cable
Test cable 1.85 mm (f) to 1.85 mm (m)
GORE
EN0CB0CB024
0
5
Test cable
6
Adapter cable
1 m long
SMP male to SMA male
-
1129.8259.00 1
7
Adapter cable
0.5 m long
SMP male to SMP male
-
1129.8265.00 1
8
SMA cable
0.5 m long
SMA male to SMA male
-
1142.5895.00 2
9
SMA cable
1 m long
SMA male to SMA male
-
1142.5889.00 2
10
BNC cable
1 m to 2 m long
BNC male to BNC male
-
e.g.
1
1100.8850.00
11
Adapter
SMA female to N male
-
4012.5837.00 2
12
Adapter
N male to BNC female
-
0118.2812.00 1
13
Termination
SMA termination. 50 V male
-
0249.7823.00 3
14
Calibration kit
1.85mm, 50
R&S ZV-Z218
5011.6571.02 1
15
R&S SMP adapter
SMP female to SMP female
-
1093.6869.00 1
16
Adapter board
Extension 150 mm high, 48 pins, 2 mm
pitch
-
1100.3542.02 1
4-pin mini-DIN plug
R&S ZV-Z71
1164.1005.02 1
17
Conn. Cables for
DC Inputs
18
Cable tool
1145.1155.82
R&S NRP
+ Sensor
. DC to 67 GHz.
Rosenberger
11W 101-000
3.61
1306.4688.00 1
1
1
E-5
Troubleshooting
R&S ZVA
Troubleshooting - Power-up Problems
•
Fault: It is not possible to turn on the ZVA.
Action
Check mains switch on the rear panel
Check LED is yellow (standby)
Turn on instrument. Check LED is green
•
Cause of fault / remedy
Mains switch OFF: Turn on at mains switch.
LED does not come on:
Measure voltage at X92.C23
(Front module controller):
Nom. value: +13.5 V ± 1V
Nom. value reached: Fault in key pad or controller.
No voltage:
Power supply defective or short to12 V standby.
LED does not come on:
Measure the PWR-ON signal at power supply
X92.B24:
< 1V for ON
Voltage > 1V: Key pad or controller defective.
Fault: Fan not working.
Action
Check voltage at connector:
X35, X36, X37 pin 3:
nom. value 12V
Cause of fault / remedy
If no voltage can be measured the fan fuse may be
defective (F12, F62, F63)
Select Service Function
Set Service Level 1
Set Service Function 2.5.0.11.1.5
(max. fan speed)
Check voltage at connector:
X35, X36, X37 pin 3:
nom. value 0.9V
1145.1155.82
3.62
E-5
R&S ZVA
Troubleshooting
Troubleshooting Boot Problems
•
Fault: ZVA does not start the measurement application.
The first action the ZVA performs after power-up is booting BIOS for the processor. When the processor
has been successfully initialised, the Windows XP start-up procedure begins. Then, the measurement
application is loaded as an autostart program.
If there are errors during the boot phase, messages indicate possible defects.
The message “No System Disk or Disk error…” indicates that the hard disk data is corrupt. If this is the
case, replace the hard disk.
If the operating system on the hard disk has been corrupted and so cannot be loaded correctly,
Windows XP outputs a “blue screen”.
This screen summarizes all the key information about the internal status of the processor.
1145.1155.82
3.63
E-5
Troubleshooting
R&S ZVA
Troubleshooting - Boot Error
If the message below appears on the screen when the boot procedure has been completed,
Warning: Boot error occurred. For details browse Error Log file.
the cause of the error can be found in the Error-Log file.
INFO
Setup
Info
Press the Error Log softkey.
The results are displayed on the screen.
Hardware
Info
Selftest
Error
Log
OPTION
OCXO
ZVAB-B4
Del Error
Log
Cause of error: Data cannot be read from one or more boards.
When the instrument is booted, all the calibration data that is required must be written to the processor’s
RAM.
When the NWA application is started, the entry on the hard disk is compared with the Eprom data on the
board. If the data matches, the data is loaded from the hard disk into RAM. If there is not a match, the Eprom
data is written to the hard disk and then loaded into RAM.
If the data at the specified address cannot be read, a check is made in Config.ini to check if the board in
question should be present. If so, the board is simulated (i.e. if this board is present and is functioning
physically, the instrument will function) and an entry is made in the ErrorLog file.
If a board must always be physically present, (frequency reference, synthesizer1, NetworkControler1,
reflectometer1, reflectometer2), an error message is output.
See: Troubleshooting with the Selftest
1145.1155.82
3.64
E-5
R&S ZVA
Troubleshooting
Troubleshooting with the Selftest
The selftest is used to check supply voltages to the boards, including voltages generated on the boards
themselves. On the frequency reference board, two clock signals (128 MHz and ADC-CLK) are also
measured.
Starting the selftest:
• Select Service Level 2 (see Service Functions) – this means that the temperature sensor readings
are displayed and tighter voltage tolerances used.
• Call the selftest in the INFO menu:
INFO
Setup
Info
Hardware
Info
Start the selftest with the Selftest softkey.
The selftest results are displayed on the
screen.
Selftest
Error
Log…
Del Error
Log
In the selftest result-table, an abbreviation is used for every board designation:
Fr
Frequency reference
Nd1
Network controller1, digital section
Nd2
Network controller2, digital section (only 4-oort instruments)
Sy1/DDSCON
Synthesizer1
Sy1/DDSCON
Synthesizer2(only 3-port and 4-port instruments)
Rm1
Reflectometer port1
Rm2
Reflectometer port2
Rm3
Reflectometer port3 (applies only to 3-port and 4-port-instruments)
Rm4
Reflectometer port4 (applies only to 4-port instruments)
1145.1155.82
3.65
E-5
Troubleshooting
R&S ZVA
Total selftest status: user mode ---PASSED--Instrument Type: ZVA8 with 4 Ports
Part Number: 1145.1110k10
Product ID: 01.00
Serial Number: 100124
IP Addresses
IP Address: 0.0.0.0&nbs;
Subnet Mask: 0.0.0.0
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
IP Address: 127.0.0.1 (Localhost)
Subnet Mask: 255.0.0.0
SyMapping: ZVA8_P4
LO Divider: is not active
Date: 05/28/04
Time: 14:52:57
Voltages Fr
Test description
Min
Max
Result
State
+10V_A SUPPLY
1.550V
1.950V
1.756V
PASSED
+5V_A SUPPLY
1.400V
1.800V
1.560V
PASSED
+5V_REF
1.400V
1.800V
1.560V
PASSED
+12V_STB
1.900V
2.300V
2.112V
PASSED
128_VCXO
0.800V
4.000V
2.696V
PASSED
ADC_CLK
0.800V
4.000V
2.060V
PASSED
-10V_A SUPPLY
1.900V
2.300V
2.128V
PASSED
-5V_A SUPPLY
2.100V
2.500V
2.264V
PASSED
Test description
Min
Max
Result
State
+5VA_ADC
2.250V
2.750V
2.488V
PASSED
+2.5VD_MDD1
1.125V
1.375V
1.264V
PASSED
+2.5VD_MDD2
1.125V
1.375V
1.264V
PASSED
+1.5VD_FCON
0.675V
0.825V
0.752V
PASSED
-5VA_ADC
2.250V
2.750V
2.464V
PASSED
DGND1
0.000V
0.200V
0.000V
PASSED
DGND2
0.000V
0.200V
0.000V
PASSED
AGND
0.000V
0.200V
0.000V
PASSED
Voltages Nd1
1145.1155.82
3.66
E-5
R&S ZVA
Troubleshooting
Voltages Nd2
Test description
Min
Max
Result
State
+5VA_ADC
2.250V
2.750V
2.484V
PASSED
+2.5VD_MDD1
1.125V
1.375V
1.260V
PASSED
+2.5VD_MDD2
1.125V
1.375V
1.260V
PASSED
+1.5VD_FCON
0.675V
0.825V
0.752V
PASSED
-5VA_ADC
2.250V
2.750V
2.460V
PASSED
DGND1
0.000V
0.200V
0.000V
PASSED
DGND2
0.000V
0.200V
0.000V
PASSED
AGND
0.000V
0.200V
0.000V
PASSED
Test description
Min
Max
Result
State
+10V_A SUPPLY
1.500V
2.000V
1.752V
PASSED
+5V_A SUPPLY
1.300V
1.800V
1.560V
PASSED
+5V_REF
1.300V
1.800V
1.568V
PASSED
+7V_A SUPPLY
1.400V
1.900V
1.628V
PASSED
Test description
Min
Max
Result
State
+10V_A SUPPLY
1.500V
2.000V
1.752V
PASSED
+5V_A SUPPLY
1.300V
1.800V
1.560V
PASSED
+5V_REF
1.300V
1.800V
1.564V
PASSED
+7V_A SUPPLY
1.400V
1.900V
1.616V
PASSED
Voltages Sy1\DDSCON
Voltages Sy2\DDSCON
Voltages Rm1
Test description
Min
Max
Result
State
GND
0.000V
0.200V
0.000V
PASSED
GND
0.000V
0.200V
0.000V
PASSED
+5V SUPPLY
2.300V
2.700V
2.496V
PASSED
+10.5VA SUPPLY
2.300V
2.800V
2.564V
PASSED
+10.5VB SUPPLY
2.300V
2.800V
2.564V
PASSED
+12V FAN
2.000V
2.600V
2.216V
PASSED
+12V SUPPLY
2.000V
2.600V
2.204V
PASSED
-12V SUPPLY
1.600V
2.000V
1.796V
PASSED
Test description
Min
Max
Result
State
GND
0.000V
0.200V
0.000V
PASSED
GND
0.000V
0.200V
0.000V
PASSED
Voltages Rm2
1145.1155.82
3.67
E-5
Troubleshooting
R&S ZVA
+5V SUPPLY
2.300V
2.700V
2.500V
PASSED
+10.5VA SUPPLY
2.300V
2.800V
2.576V
PASSED
+10.5VB SUPPLY
2.300V
2.800V
2.592V
PASSED
+12V FAN
2.000V
2.600V
2.204V
PASSED
+12V SUPPLY
2.000V
2.600V
2.204V
PASSED
-12V SUPPLY
1.600V
2.000V
1.796V
PASSED
Test description
Min
Max
Result
State
GND
0.000V
0.200V
0.000V
PASSED
GND
0.000V
0.200V
0.000V
PASSED
+5V SUPPLY
2.300V
2.700V
2.500V
PASSED
+10.5VA SUPPLY
2.300V
2.800V
2.584V
PASSED
+10.5VB SUPPLY
2.300V
2.800V
2.600V
PASSED
+12V FAN
2.000V
2.600V
2.196V
PASSED
+12V SUPPLY
2.000V
2.600V
2.220V
PASSED
-12V SUPPLY
1.600V
2.000V
1.800V
PASSED
Test description
Min
Max
Result
State
GND
0.000V
0.200V
0.000V
PASSED
GND
0.000V
0.200V
0.000V
PASSED
+5V SUPPLY
2.300V
2.700V
2.492V
PASSED
+10.5VA SUPPLY
2.300V
2.800V
2.604V
PASSED
+10.5VB SUPPLY
2.300V
2.800V
2.568V
PASSED
+12V FAN
2.000V
2.600V
2.216V
PASSED
+12V SUPPLY
2.000V
2.600V
2.136V
PASSED
-12V SUPPLY
1.600V
2.000V
1.804V
PASSED
Voltages Rm3
Voltages Rm4
Voltages Fr
Voltages Nd1
Voltages Nd2
Voltages Sy1\DDSCON
Voltages Sy2\DDSCON
Voltages Rm1
Voltages Rm2
Voltages Rm3
Voltages Rm4
Home
1145.1155.82
3.68
E-5
R&S ZVA
Troubleshooting
Interpreting the Results of the Selftest
Negative voltages are transformed into positive voltages by means of a positive voltage and a resistor
network because the A/D converters that are used can handle only positive voltages. This is why an
acceptable negative voltage may elicit a FAIL because the associated positive voltage is out of
tolerance.
The voltages supplied by the power supply are not checked directly. The failure of a power supply
voltage can, however, be deduced from FAILs of certain voltages on several boards. The following
Table shows how the board-oriented voltages checked during the selftest are derived from the power
supply voltages.
Power
supply
+3.4 V
Fr
Nd
+5.2 V
+6.5 V
+8.25 V
+5V_A
+5V_REF
+2.5VD_MDD1
+2.5VD_MDD2
+1.5VD_FCON
+12.25 V
-6.5 V
-12.25 V
+10V_A
+12V_STB
-5V_A
-10V_A
+5VA_ADC
-5VA_ADC
Sy
+5V_A
+5V_REF
+7V_A
+10V_A
Rm
+5V
+10.5VA
+10.5VB
+12V
+12V FAN
-12V
If the voltages listed in a column are all FAIL, the corresponding power supply voltage has failed or is
out-of-tolerance. The power supply must then be replaced.
On the motherboard, there is a separate fuse for each board and for each of the power supply voltages
used on the board. If a FAIL message is output, the first action to take is to check the fuse. The LO
divider board must be removed before the fuses on the motherboard can be checked (See Chapter
Board Replacement).
If an internal board voltage is out-of-tolerance, even though the power supply voltages used on the
board are OK, the board must be replaced.
1145.1155.82
3.69
E-5
Troubleshooting
R&S ZVA
Checking the Temperature Sensors
Select Service Level 2 (see Service Functions).
Setup
Info
INFO
When the Hardware Info softkey is pressed
information about the installed hardware, the
results of temperature measurements and …
are displayed.
Hardware
Info
Selftest
Error
Log…
Del Error
Log
Temperature Info
Current Temperature Readings
Component
Sensor
Temperature
Sensor
Temperature
Sensor
Motherboard
Near NC:
33.75°C Near SY:
34.75°C Near PS:
Netcon 1
Analog:
40.25°C Digital:
49.75°C
Netcon 2
Analog:
----- Digital:
-----
Reflectometer 1
Generator:
38.50°C
Reflectometer 2
Generator:
36.00°C
Reflectometer 3
Generator:
38.25°C
Reflectometer 4
Generator:
39.25°C
Synthesizer 1
Synth. 1:
Synthesizer 2
Synth. 2:
Temperature
38.50°C
Highly elevated temperature values indicate a fan failure.
1145.1155.82
3.70
E-5
R&S ZVA
Troubleshooting
Service Functions
The service functions allow you to examine particular circuit sections on specific boards or to make
well-defined settings that would normally change automatically according to the state of the instrument
(e.g. the IF). There are a number of service functions which, if used incorrectly, could cause the
instrument to malfunction. Usually, these functions are disabled. They are enabled only after a code
number (PASSWORD) has been entered.
There are three different service levels:
Service level
Password
0
No password necessary
1
894129
2
30473035
MENU
Service Function
System
System Config…
Measurement Wizard [
Print
[
Enter Password:
\ Internal Reference
External Reference
Preset
GPIB Address…
Service Function…
External Tools
1145.1155.82
[
3.71
E-5
Troubleshooting
R&S ZVA
Service Function Structure
.
Group
Main ID
.
Sub ID
.
Function
Group
Applies to
1
API
2
HW (boards)
Boards
Boards
Main ID
Sub ID
0: All boards
0
1: Network controller1
0: All board
.
Address
.
Data
1: PCI
2: ND
3: NA
2: Network controller2
5: Motherboard
0:
9: Frequency reference
0:
11: Synthesizer1
0: All board
1: SY1
2: SY2
3: SY3
4: SY4
12: Synthesizer2
21: Reflectometer1
0: all board
1: GEN
2: REC
22: Reflectometer 2
23: Reflectometer 3
24: Reflectometer 4
1145.1155.82
3.72
E-5
R&S ZVA
Troubleshooting
Group 1:
General Functions
Functions
Data
Serv. Lev.
Enables/disables the peak detector and RMS 1.0.0.1.X
detector independently of the model
0
Use disabled
2
1
Use enabled
1.0.0.5.X
0
Use disabled
1
Use enabled
Activates or deactivates the setting of measured 1.1.0.2.X
values to default values when status messages
are issued due to HW faults
0
Deactivate default values
1
Activate default values
Activates or deactivates factory calibration for 1.1.0.3.X
the active setup
0
Deactivate factory calibration
1
Activate factory calibration
Enable/disables the arbitrary mode settings in
the port configuration (e.g. LowNoise/
LowDistortion) independently of the model
Service
function
2
0
0
Group 2:
General Functions
Functions
Service function
Suppress error-message box
2.0.0.0.X
Selftest all boards
2.0.0.5.0.0
Data
X=0
MSG box is output (default state)
X=1
MSG box is suppressed (error is
nevertheless entered in the log file)
Serv. Lev.
1
0, 1 or 2
Network controller
Functions
Service function
ND1:Read Temp (addr.:68)
2.1.2.3
1
ND2:Read Temp (addr.:68)
2.2.2.3
1
ND[1..2] Selftest
2.[1-2].2.5.0.0
0, 1 or 2
NA1:Read Temp (addr.:69)
2.1.3.3
1
NA2:Read Temp (addr.:69)
2.2.3.3
1
1145.1155.82
3.73
Data
Serv. lev.
E-5
Troubleshooting
R&S ZVA
Motherboard
Functions
Service function
Data
Serv. lev.
MB: Fan manual
2.5.0.11.1.X
X= 0 to 5
MB: Fan automatic
2.5.0.11.0
1
MB:Read Temp
2.5.0.3.1
1
2.5.0.3.2
1
2.5.0.3.3
1
1
Front (NC) (addr.:205)
MB: Read Temp
Rear (SY) (addr.: 204)
MB: Read Temp
Back (PS) (addr.: 202)
Frequency reference
Functions
Service function
FR Selftest
2.9.0.5.0.0
Data
Serv.lev.
0, 1 or 2
Reflectometers
Functions
Service function
Data
Serv.lev.
RM[1-4]: Fan manual
2.[21-24].0.11.X
X = 1 to 5
1
RM[1-4]:Fan automatic
2.[21-24].0.11.0
1
RM[1-4]: Read Temp Gen
2.[21-24].1.3
1
RM[1-4]: Read Temp Rec
2.[21-24].2.3
1
RM[1-4]: Selftest
2.[21-24].0.5.X
RM[1-4]: Read OVL
2.[21-24].0.12
1
RM[1-4]: OVL Reset
2.[21-24].0.13
1
RM[1-4] Generator Selftest
2.[21-24].1.5.0.0
0, 1 or 2
RM[1-4]: IF shift
2.[21-24].2.18.ZF
X = 0 to 4
IF in Hz
1
0
0 = IF via shift table
1145.1155.82
3.74
E-5
R&S ZVA
Troubleshooting
Determining which Boards are defective
The table below lists boards that are probably defective based on the faults that occurred during the
performance test.
Defective board
Problem with:
Probable
Also possible
Frequency accuracy
Frequency reference
SSB phase-noise
Only one port
All ports
Synthesizer1
Frequency reference
Level accuracy
Only one port
All ports
Reflectometer associated with defective port
Synthesizer1
Max. output level
Only one port
All ports
Reflectometer associated with defective port
Synthesizer1
Absolute accuracy wave quantity a
Reflectometer associated with defective port
Level linearity
Reflectometer associated with defective port
Harmonic ratio
Reflectometer associated with defective port
Spurious suppression
Synthesizer1
Matching portx
Bridge unit of reflectometer associated with the
defective port
Directivity portx
Bridge unit of reflectometer associated with the
defective port
Receiver absolute accuracy Port 1, 2
Port 3, 4
All ports
Reflectometer associated with defective port
Reflectometer associated with defective port
Synthesizer1
Network controller1
Network controller2
Frequency reference
Receiver linearity for high levels Portx
All ports
Reflectometer associated with defective port
LO divider
LO divider
Synthesizer2
Receiver linearity for low levels
Network controller1
Network controller2
Port1, 2
Port3, 4
Synthesizer1
Receiver noise level portx
Reflectometer associated with defective port
Synthesizer2 or
synth.1 for 2-port models
Dynamic range portx
Reflectometer associated with defective port
(see Circular 10028)
Synthesizer2 or.
synth.1 for 2-port models
DC measurement input1V
Motherboard
Network controller1
DC measurement input 10V
Motherboard
Network controller1
Frequency reference input/output
Frequency reference
Accuracy on S-parameter measurements
depending on meas. bandwidth
See Circular 10029
A board test should be performed before the board that has been deduced to be defective is replaced.
1145.1155.82
3.75
E-5
Troubleshooting
R&S ZVA
Board Test
When boards are being tested, internal sources are used whenever possible. This means that it is
always assumed that the downstream board in the signal path is OK. If a clear fault is not present, the
order of the board tests given below should always be followed.
The inputs and outputs of the boards to be tested can be accessed via cables in the lower section of the
instrument (except the frequency reference board).
Opening the instrument
(See Chapter 5, drawing1145.1110)
Turn off the instrument and disconnect from the mains, screw off the 4 rear-panel feet (460) and
pull off the enclosure (400) backwards.
Remove the instrument base cover (297) after undoing the screws (299).
Only when testing the frequency reference board:
Lift off the instrument top cover (296) after undoing the screws (298).
1145.1155.82
3.76
E-5
R&S ZVA
Troubleshooting
Testing the frequency reference board
(see Test Equipment)
Remove the board from the instrument.
Reinsert board and extension card.
Connect the output to be tested to the spectrum analyzer using an adapter cable and
adapter SMA-N.
Set the frequencies listed in the table.
Check signals according to following table.
Signal
Connector
Frequency
Nom. level
NA1_AD_CLK
X103
80 MHz
10 dBm ±1dB
NA2_AD_CLK
X104
80 MHz
10 dBm ±1dB
SY1_REF
X105
128 MHz
10 dBm ±1dB
SY2_REF
X106
128 MHz
10 dBm ±1dB
REF_10_OUTIN
X107
10 MHz
6 dBm ±1dB
Setting
Menu/System/Internal
Reference
The board must be replaced if the signal is more than 2 dB below the stated nominal level.
Connect the frequency reference output of the spectrum analyzer to X107 (REF_10_OUTIN) using
an adapter cable and adapter SMA-N.
Connect X105 or X106 (SY1_REF or. SY2_REF) to the spectrum analyzer using an adapter cable
and adapter SMA-N.
The 128 MHz signal’s frequency must precisely equal its nominal frequency.
If the frequency differs in any way (e.g. 128.001 MHz), replace the board.
1145.1155.82
3.77
E-5
Troubleshooting
R&S ZVA
Testing the Synthesizer Board
N.B.:
Synthesizers with part numbers 1145.xxxx or 1300.xxxx are no longer available. In case of
defect please contact the Central Service in Munich.
Disconnect source (or local) cable at the reflectometer (1 to 4, depending on which synthesizer
section is to be tested).
Connect the end of the cable to the spectrum analyzer input via an adapter cable and adapter
SMA-N.
N.B.:
Bend the source cable as little as possible, if necessary secure adapter cable with
adhesive tape.
Enter service function 2.21.2.18.17512345 (IF = 17.512345 MHz).
[ Mode : Spurious Avoidance : LO > RF ]
Set the frequencies listed in the table on the ZVA and check the values.
[ Sweep : Sweep Type : CW Mode : CW Frequency : …Hz]
[ Sweep : Single : Restart]
Synthesizer-LS 1302.4025.xx
Source Mod. 02 and Mod. 20
Frequency
(ZVA setting)
Source Level
(Mod. 02)
2nd harmonic
3rd harmonic
300 kHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
100 MHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
1 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
2 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
3 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
4 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
6 GHz
+3 dBm to -7 dBm
< -27 dBc
< -30 dBc
8 GHz
+3 dBm to -7 dBm
< -27 dBc
< -30 dBc
Port setting
Source output
Isolation
Port1 inactive
X168
-90 dBc ±5 dB
Port2 active
X169
Port1 active
X168
Port2 inactive
X169
Isolation of source switch1 to 4
ZVA frequency 8 GHz
Port no.
1
2
1145.1155.82
3.78
-90 dBc ±5 dB
E-5
R&S ZVA
Troubleshooting
Local Mod. 02
Frequency
(ZVA setting)
LO-Frequency
(Spec analyzer
setting)
Local Level
(Mod. 02)
2nd
harmonic
3rd harmonic
300 kHz
17.812345 MHz
+2 dBm to -15 dBm
< -5 dBc
< +2 dBc
100 MHz
117.512345 MHz
+2 dBm to -15 dBm
< -5 dBc
< +2 dBc
1 GHz
1017.512345 MHz
+2 dBm to -4 dBm
< -5 dBc
< -5 dBc
2 GHz
2017.512345 MHz
+2 dBm to -4 dBm
< -5 dBc
< -5 dBc
3 GHz
3017.512345 MHz
+2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
3.8 GHz
3817.512345 MHz
+2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
4 GHz
4017.512345 MHz
+2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
5.2 GHz
5217.512345 MHz
+2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
5.3 GHz
5317.512345 MHz
+2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
7.2 GHz
7217.512345 MHz
+2 dBm to -5 dBm
< -5 dBc
< -5 dBc
8 GHz
8017.512345 MHz
+2 dBm to -5 dBm
< -5 dBc
< -5 dBc
Frequency
(ZVA setting)
LO-Frequency
(Spec analyzer
setting)
Local Level
(Mod. 24)
2nd
harmonic
3rd harmonic
10 MHz
27.512345 MHz
-3 dBm to -20 dBm
< -5 dBc
< +2 dBc
100 MHz
117.512345 MHz
-3 dBm to -20 dBm
< -5 dBc
< +2 dBc
1 GHz
1017.512345 MHz
-3 dBm to -9 dBm
< -5 dBc
< -5 dBc
2 GHz
2017.512345 MHz
-3 dBm to -9 dBm
< -5 dBc
< -5 dBc
3 GHz
3017.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
3.8 GHz
3817.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
4 GHz
4017.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
5.2 GHz
5217.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
5.3 GHz
5317.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
7.2 GHz
7217.512345 MHz
-3 dBm to -10 dBm
< -5 dBc
< -5 dBc
8 GHz
8017.512345 MHz
-3 dBm to -10 dBm
< -5 dBc
< -5 dBc
Local Mod. 20
1145.1155.82
3.79
E-5
Troubleshooting
R&S ZVA
Synthesizer-DS 1302.5180.xx
Source 1 to 4 (set port1 to 4 active)
Frequency
(ZVA setting)
Source Level
2nd harmonic
3rd harmonic
300 kHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
100 MHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
1 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
2 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
3 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
4 GHz
+3 dBm to -5 dBm
< -27 dBc
< -30 dBc
6 GHz
+3 dBm to -7 dBm
< -27 dBc
< -30 dBc
8 GHz
+3 dBm to -7 dBm
< -27 dBc
< -30 dBc
Port setting
Source output
Isolation
Port1 inactive
X165
-90 dBc ±5 dB
Port2 active
X166
Port1 active
X165
Port2 inactive
X166
-90 dBc ±5 dB
Port3 inactive
X168
-90 dBc ±5 dB
Port4 active
X169
Port3 active
X168
Port4 inactive
X169
Isolation of source switch1 to 4
ZVA frequency 8 GHz
Port no.
1
2
3
4
-90 dBc ±5 dB
The cable loss must also be taken into account at the stated levels. For the specified cable it is
0.25 dB/GHz (0.5 m) 0.5 dB/GHz (1 m).
The board must be replaced if the level is more than 2 dB below the specified value or the other values
are more than 2 dB above their specified value.
1145.1155.82
3.80
E-5
R&S ZVA
Troubleshooting
Synthesizer-LO 1302.4248.02
Local 1 to 4 (set port1 to 4 active)
Frequency
(ZVA setting)
LO-Frequency
(Spec analyzer
setting)
Local Level
2nd
harmonic
3rd
harmonic
300 kHz
17.812345 MHz
2 dBm to -15 dBm
< -5 dBc
< 2 dBc
100 MHz
117.512345 MHz
2 dBm to -15 dBm
< -5 dBc
< 2 dBc
1 GHz
1017.512345 MHz
2 dBm to -4 dBm
< -5 dBc
< -5 dBc
2 GHz
2017.512345 MHz
2 dBm to -4 dBm
< -5 dBc
< -5 dBc
3 GHz
3017.512345 MHz
2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
3.8 GHz
3817.512345 MHz
2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
4 GHz
4017.512345 MHz
2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
5.2 GHz
5217.512345 MHz
2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
5.5 GHz
5517.512345 MHz
2 dBm to -1.5 dBm
< -5 dBc
< -5 dBc
7.2 GHz
7217.512345 MHz
3 dBm to -4 dBm
< -5 dBc
---
8 GHz
8017.512345 MHz
3 dBm to -4 dBm
< -5 dBc
---
Synthesizer-LO 1302.4248.20
Local 1 to 4 (set port1 to 4 active)
1145.1155.82
Frequency
(ZVA setting)
LO-Frequency
(Spec analyzer
setting)
Local Level
2nd
harmonic
3rd
harmonic
300 kHz
17.812345 MHz
-3 dBm to -20 dBm
< -5 dBc
< 2 dBc
100 MHz
117.512345 MHz
-3 dBm to -20 dBm
< -5 dBc
< 2 dBc
1 GHz
1017.512345 MHz
-3 dBm to -9 dBm
< -5 dBc
< -5 dBc
2 GHz
2017.512345 MHz
-3 dBm to -9 dBm
< -5 dBc
< -5 dBc
3 GHz
3017.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
3.8 GHz
3817.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
4 GHz
4017.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
5.2 GHz
5217.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
5.5 GHz
5517.512345 MHz
-3 dBm to -6.5 dBm
< -5 dBc
< -5 dBc
7.2 GHz
7217.512345 MHz
-3 dBm to -10 dBm
< -5 dBc
---
8 GHz
8017.512345 MHz
-3 dBm to -10 dBm
< -5 dBc
---
3.81
E-5
Troubleshooting
R&S ZVA
Synthesizer-12
Source signals
Local signals
1145.1155.82
(W168, W169) with synth. 1305.3002.02 and synth. 1305.3002.04
(W165, W166, W168, W169) with synth. 1305.7220.02
Frequency
(ZVA setting)
Source Level
(Mod. 02)
2nd harmonic
10 MHz
+10 dBm to -10 dBm
-----
100 MHz
+10 dBm to -10 dBm
-----
300 MHz
+10 dBm to -10 dBm
< -25 dBc
1 GHz
+10 dBm to -10 dBm
-----
2 GHz
+10 dBm to -10 dBm
-----
2.5 GHz
+10 dBm to -10 dBm
< -25 dBc
3 GHz
+10 dBm to -10 dBm
-----
4 GHz
+10 dBm to -10 dBm
-----
6 GHz
+10 dBm to -10 dBm
-----
8 GHz
+10 dBm to -10 dBm
-----
10 GHz
+10 dBm to -10 dBm
-----
12 GHz
+10 dBm to -10 dBm
-----
(W165, W166) with synth. 1305.3002.02 and synth. 1305.3002.03
(W155, W156, W158, W159) with synth. 1305.7220.02
Frequency
(ZVA setting)
LO-Frequency
(Spec analyzer
setting)
Source Level
(Mod. 02)
30 MHz
47.512345 MHz
+10 dBm to -10 dBm
100 MHz
117.512345 MHz
+10 dBm to -10 dBm
1 GHz
1.017512345 GHz
+10 dBm to -10 dBm
2 GHz
2.017512345 GHz
+10 dBm to -10 dBm
3 GHz
3.017512345 GHz
+10 dBm to -10 dBm
4 GHz
4.017512345 GHz
+10 dBm to -10 dBm
6 GHz
6.017512345 GHz
+10 dBm to -10 dBm
8 GHz
8.017512345 GHz
+10 dBm to -10 dBm
10 GHz
10.017512345 GHz
+10 dBm to -10 dBm
12 GHz
12.017512345 GHz
+10 dBm to -10 dBm
3.82
E-5
R&S ZVA
Troubleshooting
Testing the Reflectometer RM8
Generator levels
It is assumed that the synthesizer section (synthesizer1) associated with the reflectometer to be tested
is OK.
Loosen cable W514 (GEN -> Bridge unit) at both ends and screw off at the generator output GEN.
Note: When loosening, support the cable with a 7mm spanner
Connect the generator output to the spectrum analyzer using the SMA cables () and adapter SMAN.
Set the power to 8 dBm
Set the ZVA to the CW sweep mode.
Set the frequencies listed in the table.
Frequency
Level
2nd harmonic
3rd harmonic
300 kHz
16 dBm
---
---
50 MHz
16 dBm
< - 21 dBc
< - 21 dBc
1 GHz
16 dBm
< - 21 dBc
< - 21 dBc
3 GHz
16 dBm
< - 21 dBc
< - 21 dBc
6 GHz
16 dBm
< - 21 dBc
---
8 GHz
16 dBm
< - 21 dBc
---
With the stated levels, the cable loss must still be taken into account. For the specified cable it is
0.25 dB/GHz.
Receiver levels
The following is assumed:
• The LO synthesizer section (synthesizer1 mod. 04, synthesizer2) associated with the reflectometer
to be tested is OK.
• The network controller associated with the reflectometer to be tested is OK.
• One reflectometer in the instrument is functioning.
Loosen cable W515 (Bridge unit -> MEAS) and cable W518 (Bridge unit -> REF) at both ends and
screw off at the MEAS and REF receiver inputs.
N.B.: When loosening, support the cable with a 7mm spanner
Connect the receiver input (MEAS or REF) to a functioning instrument port using an adapter cable
and adapter SMA-N.
Set the ZVA to the CW sweep mode.
Set the frequencies and output levels for the port used for the measurement as indicated in the
table and read off the level for the receiver to be tested (wave quantity ax or bx).
1145.1155.82
3.83
E-5
Troubleshooting
R&S ZVA
Frequency
Output level
Displayed level
ax or bx
300 kHz
-20 dBm
0 dBm
50 MHz
-20 dBm
0 dBm
1 GHz
-20 dBm
0 dBm
3 GHz
-20 dBm
0 dBm
6 GHz
-20 dBm
0 dBm
8 GHz
-20 dBm
0 dBm
With the stated levels, the cable loss must still be taken into account. For the specified cable, it is
0.25 dB/GHz (0.5 m) or. 0.5 dB/GHz (1 m).
If the measured values are more than 3 dB below the levels and ratios list in the table, the board must
be replaced.
Bridge unit levels
The following is assumed:
• One reflectometer in the instrument is OK.
Method 1:
The generator section of the associated reflectometer is OK (output level at the port
specifications).
meets
Loosen cable W515 (Bridge unit -> MEAS) and cable W518 (Bridge unit -> REF) at both ends and
disconnect at the bridge unit.
N.B.: When loosening, support the cable with a 7mm spanner
Connect the bridge unit output (MEAS = connector W515 or REF = connector W518) to a
functioning port using the SMA cable and adapter SMA-N (measure wave quantity bx). Terminate
the bridge unit output that is not used with an SMA termination.
Screw the SHORT from a N-calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + (linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Set the frequencies and levels listed in the table for the reflectometer associated with the bridge
unit (port) and measure the level (wave quantity bx) at the port used for the measurement.
1145.1155.82
3.84
E-5
R&S ZVA
Troubleshooting
Frequency
Level
Output level MEAS
Output level REF
300 kHz
0 dBm
-18 dBm
-32 dBm
50 MHz
0 dBm
-18 dBm
-32 dBm
1 GHz
0 dBm
-18 dBm
-32 dBm
3 GHz
0 dBm
-18 dBm
-32 dBm
6 GHz
0 dBm
-18 dBm
-32 dBm
8 GHz
0 dBm
-18 dBm
-32 dBm
With the stated levels, the cable loss must still be taken into account. For the specified cable it is
0.25 dB/GHz.
If the measured values are more than 3 dB below the levels in the table, the board must be replaced.
Method 2:
The receive section of the associated reflectometer is OK.
Loosen cable W514 (GEN -> Bridge unit) at both ends and screw off at the bridge unit.
N.B.: When loosening, support the cable with a 7mm spanner
Connect the bridge input (connector W514) to a functioning port using the SMA cable and SMA-N
adapter.
Screw the SHORT from a N-calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + (linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Set the frequencies and levels listed in the table at the port used for the measurement and measure
the level (wave quantity ax or bx) at the reflectometer associated with the bridge unit (port).
Frequency
Level
Level ax and bx
300 kHz
8 dBm
0 dBm
50 MHz
8 dBm
0 dBm
1 GHz
8 dBm
0 dBm
3 GHz
8 dBm
0 dBm
6 GHz
8 dBm
0 dBm
8 GHz
8 dBm
0 dBm
With the stated levels, the cable loss must still be taken into account. For the specified cable it is
0.25 dB/GHz.
If the measured values are more than 3 dB below the levels given in the table, the board must be
replaced.
1145.1155.82
3.85
E-5
Troubleshooting
R&S ZVA
Bridge Directivity
The following is assumed:
• The generator and receiver sections of the reflectometer associated with the bridge unit are OK.
Perform a sweep from 300 kHz to 8 GHz, measure Ratio bx/ax Source Portx
Screw the SHORT from a N-calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector, save measured values (More Mem :
Data -> Mem3).
Screw the MATCH from the calibration kit to the port connector.
Select User Def Math : linMag(Data) / ((linMag(Mem2) + linMag(Mem3)) / 2 : Math = User Def
The trace gives the directivity.
Frequency range
Directivity
300 kHz to 50 MHz
< -10 dB
50 MHz to 8 GHz
< -16 dB
If the measured values are greater than the values stated in the table, the bridge unit must be replaced.
Bridge unit: Port Matching
It is assumed that there is a functioning reflectometer in the instrument.
Loosen cables W514 (GEN -> Bridge unit), W515 (Bridge unit -> MEAS) and W518 (Bridge unit ->
REF) at both ends and unscrew at the bridge unit.
N.B.: When loosening, support the cable with a 7mm spanner
Terminate the bridge unit input and bridge unit outputs with 3 SMA terminations.
Connect N test cable to a functioning instrument port and perform a 1-port calibration at the end of
the cable.
Connect the end of the test cable to the port of the bridge unit under test and display the Sxx
magnitude on the screen.
Frequency range
Sxx dB
300 kHz to 8 GHz
-18 dB
If the values in the table are exceeded, the board must be replaced.
1145.1155.82
3.86
E-5
R&S ZVA
Troubleshooting
Testing the Reflectometer RM24
Generator levels
It is assumed that the synthesizer section (synthesizer1) associated with the reflectometer to be tested
is OK.
Loosen cable W514 (GEN -> coupler unit) at both ends and screw off at the generator output GEN.
Connect the generator output to the spectrum analyzer using the SMA cable ().
Set the ZVA to the CW sweep mode.
Set the frequencies listed in the table.
Set the power listed in the table.
Frequency
Set power to
Level on GEN output
2nd harmonic
3rd harmonic
10 MHz
10 dBm
13.0 dBm
---
---
100 MHz
10 dBm
13.0 dBm
< - 21 dBc
< - 21 dBc
1 GHz
10 dBm
13.2 dBm
< - 21 dBc
< - 21 dBc
4 GHz
10 dBm
13.7 dBm
< - 21 dBc
< - 21 dBc
8 GHz
10 dBm
14.3 dBm
< - 21 dBc
< - 21 dBc
9 GHz
10 dBm
14.5 dBm
< - 21 dBc
---
15.0 dBm
---
---
7.5 dBm
---
---
8.0 dBm
---
---
8.3 dBm
---
---
12 GHz
15 GHz
18 GHz
20 GHz
10 dBm
5 dBm
5 dBm
5 dBm
With the stated levels, the cable loss must still be taken into account. For the specified cable it is
0.25 dB/GHz.
Receiver levels
The following is assumed:
• The LO synthesizer section (synthesizer1 mod. 20, synthesizer2) associated with the reflectometer
to be tested is OK.
• The network controller associated with the reflectometer to be tested is OK.
• One reflectometer in the instrument is functioning.
Loosen cable W515 (coupler unit -> MEAS) and cable W518 (coupler unit -> REF) at both ends
and screw off at the MEAS and REF receiver inputs.
Connect the receiver input (MEAS or REF) to a functioning instrument port using an adapter cable.
Set the ZVA to the CW sweep mode.
Set the frequencies and output levels for the port used for the measurement as indicated in the
table and read off the level for the receiver to be tested (wave quantity ax or bx).
1145.1155.82
3.87
E-5
Troubleshooting
R&S ZVA
Frequency
Output level
Displayed level
ax or bx
10 MHz
-30 dBm
+20 dBm ± 3 dB
100 MHz
-30 dBm
+5 dBm ± 3 dB
1 GHz
-20 dBm
-5 dBm ± 3 dB
2.5 GHz
-20 dBm
-10 dBm ± 3 dB
3 GHz
-20 dBm
-10 dBm ± 3 dB
8 GHz
-20 dBm
-10 dBm ± 3 dB
9 GHz
-20 dBm
-10 dBm ± 3 dB
12 GHz
-20 dBm
-10 dBm ± 3 dB
15 GHz
-20 dBm
-8 dBm ± 4 dB
18 GHz
-20 dBm
-8 dBm ± 4 dB
20 GHz
-20 dBm
-8 dBm ± 4 dB
With the stated levels, the cable loss must still be taken into account. For the specified cable, it is
0.25 dB/GHz (0.5 m) or. 0.5 dB/GHz (1 m).
If the measured values are more than 2 dB below the levels list in the table, the board must be
replaced.
Coupler unit levels
The following is assumed:
• One reflectometer in the instrument is OK.
Method 1:
The generator section of the associated reflectometer is OK (output level at the port meets
specifications).
Loosen cable W515 (coupler unit -> MEAS) and cable W518 (coupler unit -> REF) at both ends and
disconnect at the coupler unit.
Connect the coupler unit output (MEAS = connector W515 or REF = connector W518) to a
functioning port using the SMA cable. Terminate the coupler unit output that is not used with an
SMA termination.
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + (linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Set the frequencies and levels listed in the table for the reflectometer associated with the coupler
unit (port) and measure the level (wave quantity bx) at the port used for the measurement.
1145.1155.82
3.88
E-5
R&S ZVA
Troubleshooting
Frequency
Level
Output level MEAS
Output level REF
10 MHz
0 dBm
-50 dBm ± 3 dB
-47 dBm ± 3 dB
100 MHz
0 dBm
-35 dBm ± 3 dB
-32 dBm ± 3 dB
1 GHz
0 dBm
-15 dBm ± 3 dB
-11 dBm ± 3 dB
2 GHz
0 dBm
-10 dBm ± 3 dB
-4.7 dBm ± 3 dB
8 GHz
0 dBm
-10 dBm ± 3 dB
-3.7 dBm ± 3 dB
12 GHz
0 dBm
-10 dBm ± 3 dB
-3 dBm ± 3 dB
16 GHz
0 dBm
-12 dBm ± 4 dB
-2.3 dBm ± 4 dB
20 GHz
0 dBm
-12 dBm ± 4 dB
-1.7 dBm ± 4 dB
24 GHz
0 dBm
-12 dBm ± 4 dB
-1 dBm ± 4 dB
With the stated levels, the cable loss must still be taken into account. For the specified cable it is
0.25 dB/GHz.
If the measured values are more than 2 dB below the levels in the table, the coupler unit must be
replaced.
Method 2:
The receiver section of the associated reflectometer is OK.
Loosen cable W514 (GEN -> coupler unit) at both ends and screw off at the coupler unit.
Connect the coupler input (connector. W514) to a functioning port using the SMA cable.
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + (linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Set the frequencies and levels listed in the table at the port used for the measurement and measure
the level (wave quantity ax or bx) at the reflectometer associated with the coupler unit (port).
Frequency
Level
Level ax and bx
10 MHz
0 dBm
-3 dBm ± 1 dB
100 MHz
0 dBm
-3 dBm ± 1 dB
1 GHz
0 dBm
-3.2 dBm ± 1 dB
2 GHz
0 dBm
-3.3 dBm ± 1 dB
8 GHz
0 dBm
-4.3 dBm ± 1 dB
12 GHz
0 dBm
-5 dBm ± 1 dB
16 GHz
0 dBm
-5.7 dBm ± 1 dB
20 GHz
0 dBm
-6.3 dBm ± 1 dB
24 GHz
0 dBm
-7 dBm ± 1 dB
With the stated levels, the cable loss must still be taken into account. For the specified cable it is
0.25 dB/GHz.
If the measured values are more than 2 dB below the levels given in the table, the coupler unit must be
replaced.
1145.1155.82
3.89
E-5
Troubleshooting
R&S ZVA
Coupler Directivity
The following is assumed:
• The generator and receiver sections of the reflectometer associated with the coupler unit are OK.
Perform a sweep from 10 MHz to 24 GHz, measure Ratio bx/ax Source Portx
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector, save measured values (More Mem :
Data -> Mem3).
Screw the MATCH from the calibration kit to the port connector.
Select User Def Math : linMag(Data) / ((linMag(Mem2) + linMag(Mem3)) / 2 : Math = User Def
The trace gives the directivity.
Frequency range
Directivity
10 MHz to 12 GHz
< -15 dB
12 GHz to 24 GHz
< -10 dB
If the measured values are greater than the values stated in the table, the coupler unit must be
replaced.
Coupler unit: Port Matching
It is assumed that there is a functioning reflectometer in the instrument.
Loosen cables W514 (GEN -> coupler unit), W515 (coupler unit -> MEAS) and W518 (coupler unit > REF) at both ends and unscrew at the coupler unit.
Terminate the coupler unit input and coupler unit outputs with 3 SMA terminations.
Connect test cable to a functioning instrument port and perform a 1-port calibration at the end of the
cable.
Connect the end of the test cable to the port of the coupler unit under test and display the Sxx
magnitude on the screen.
Frequency range
Sxx dB
10 MHz to 12 GHz
< -14 dB
12 GHz to 20 GHz
< -10 dB
If the values in the table are exceeded, the coupler must be replaced.
1145.1155.82
3.90
E-5
R&S ZVA
Troubleshooting
Testing the Reflectometer RM44 and RM50
Generator levels
It is assumed that the synthesizer section (synthesizer1) associated with the reflectometer to be tested
is OK.
Loosen cable W514A (GEN -> coupler unit) or W512 (GEN -> attenuator) at both ends and screw
off at the generator output GEN.
Connect the generator output to the spectrum analyzer using the K-cable (ZVA40) or V-cable
(ZVA50).
Set the ZVA to the CW sweep mode.
Set the frequencies listed in the table.
Set the power listed in the table.
Frequency
Set power to
(without
GenAtt)
Set power to
(with GenAtt)
Level on GEN
output
2nd harmonic
3rd harmonic
10 MHz
10 dBm
9 dBm
12.0 dBm
---
---
50 MHz
10 dBm
9 dBm
12.0 dBm
< - 21 dBc
< - 21 dBc
1 GHz
10 dBm
9 dBm
12.0 dBm
< - 21 dBc
< - 21 dBc
4 GHz
10 dBm
9 dBm
12.0 dBm
< - 21 dBc
< - 21 dBc
8 GHz
10 dBm
9 dBm
12.0 dBm
< - 21 dBc
< - 21 dBc
10 GHz
10 dBm
9 dBm
14.0 dBm
< - 21 dBc
< - 21 dBc
13 GHz
10 dBm
9 dBm
14.0 dBm
< - 21 dBc
< - 21 dBc
15 GHz
10 dBm
8 dBm
14.0 dBm
< - 21 dBc
< - 21 dBc
18 GHz
10 dBm
8 dBm
14.0 dBm
< - 21 dBc
< - 21 dBc
20 GHz
10 dBm
8 dBm
14.0 dBm
< - 21 dBc
---
24 GHz
10 dBm
8 dBm
14.5 dBm
< - 21 dBc
---
28 GHz
10 dBm
7 dBm
14.5 dBm
< - 21 dBc
---
32 GHz
10 dBm
7 dBm
14.5 dBm
---
---
36 GHz
6 dBm
3 dBm
10.5 dBm
---
---
40 GHz
6 dBm
3 dBm
10.5 dBm
---
---
45 GHz (ZVA50 only)
6 dBm
3 dBm
10.5 dBm
---
---
50 GHz (ZVA50 only)
6 dBm
3 dBm
10.5 dBm
---
---
With the stated levels, the cable loss must still be taken into account.
1145.1155.82
3.91
E-5
Troubleshooting
R&S ZVA
Receiver levels
The following is assumed:
• The LO synthesizer section (synthesizer1 mod. 20, synthesizer2) associated with the reflectometer
to be tested is OK.
• The network controller associated with the reflectometer to be tested is OK.
• One reflectometer in the instrument is functioning.
Loosen the cable to the receiver input MEAS (X6) and the cable to the receiver input REF (X5) at
both ends and screw off at the receiver inputs.
Connect the receiver input (MEAS or REF) to a functioning instrument port using the K-cable
(ZVA40) or V-cable (ZVA50).
Set the ZVA to the CW sweep mode.
Set the frequencies and output levels (check with power meter) for the port used for the
measurement as indicated in the table and read off the level for the receiver to be tested (wave
quantity ax or bx).
Frequency
Output level
Displayed level
ax
Displayed level
bx
10 MHz
-40 dBm
+15 dBm ± 4 dB
+7 dBm ± 4 dB
100 MHz
-40 dBm
-5 dBm ± 4 dB
-13 dBm ± 4 dB
1 GHz
-20 dBm
-2 dBm ± 4 dB
-10 dBm ± 4 dB
3 GHz
-20 dBm
-1 dBm ± 4 dB
-9 dBm ± 3 dB
8 GHz
-20 dBm
-1 dBm ± 4 dB
-9 dBm ± 3 dB
10 GHz
-20 dBm
-1 dBm ± 4 dB
-9 dBm ± 3 dB
12 GHz
-20 dBm
-0 dBm ± 4 dB
-9 dBm ± 3 dB
15 GHz
-20 dBm
-0 dBm ± 4 dB
-9 dBm ± 3 dB
18 GHz
-20 dBm
-0 dBm ± 4 dB
-9 dBm ± 3 dB
20 GHz
-20 dBm
-0 dBm ± 4 dB
-9 dBm ± 3 dB
25 GHz
-20 dBm
-0 dBm ± 4 dB
-8 dBm ± 3 dB
30 GHz
-20 dBm
-0 dBm ± 4 dB
-8 dBm ± 3 dB
35 GHz
-20 dBm
-0.5 dBm ± 4 dB
-7 dBm ± 4 dB
40 GHz
-20 dBm
-0.5 dBm ± 4 dB
-7 dBm ± 4 dB
45 GHz (ZVA50 only)
-20 dBm
-0.5 dBm ± 4 dB
-7 dBm ± 4 dB
50 GHz (ZVA50 only)
-20 dBm
-0.5 dBm ± 4 dB
-7 dBm ± 4 dB
With the stated levels, the cable loss must still be taken into account.
If the measured values are more than 2 dB below the levels list in the table, the board must be
replaced.
1145.1155.82
3.92
E-5
R&S ZVA
Troubleshooting
Coupler levels
The following is assumed:
• One reflectometer in the instrument is OK.
Method 1:
The generator section of the associated reflectometer is OK (output level at the port meets
specifications).
Loosen cable at coupler MEAS_OUT and at coupler REF_OUT at both ends and disconnect at the
coupler.
Connect the coupler output (MEAS = connector X3 or REF = connector X4) to a functioning port
using the K cable . Terminate the coupler output that is not used with an K-termination (Vtermination).
Set the frequencies and levels listed in the table for the reflectometer associated with the coupler
(port) and measure the level (wave quantity bx) at the port used for the measurement as follows:
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + (linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Frequency
Level
Output level MEAS
Output level REF
10 MHz
0 dBm
-47 dBm ± 4 dB
-55 dBm ± 4 dB
100 MHz
0 dBm
-27 dBm ± 4 dB
-35 dBm ± 4 dB
1 GHz
0 dBm
-10 dBm ± 4 dB
-18 dBm ± 4 dB
3 GHz
0 dBm
-11 dBm ± 3 dB
-19 dBm ± 4 dB
8 GHz
0 dBm
-11 dBm ± 3 dB
-19 dBm ± 4 dB
10 GHz
0 dBm
-11 dBm ± 3 dB
-19 dBm ± 4 dB
12 GHz
0 dBm
-11 dBm ± 3 dB
-20 dBm ± 4 dB
15 GHz
0 dBm
-11 dBm ± 3 dB
-20 dBm ± 4 dB
18 GHz
0 dBm
-11 dBm ± 3 dB
-20 dBm ± 4 dB
20 GHz
0 dBm
-11 dBm ± 3 dB
-20 dBm ± 4 dB
25 GHz
0 dBm
-12 dBm ± 3 dB
-20 dBm ± 4 dB
30 GHz
0 dBm
-12 dBm ± 3 dB
-20 dBm ± 4 dB
35 GHz
0 dBm
-13 dBm ± 4 dB
-19.5 dBm ± 4 dB
40 GHz
0 dBm
-13 dBm ± 4 dB
-19.5 dBm ± 4 dB
45 GHz
0 dBm
-13 dBm ± 4 dB
-19.5 dBm ± 4 dB
50 GHz
0 dBm
-13 dBm ± 4 dB
-19.5 dBm ± 4 dB
With the stated levels, the cable loss must still be taken into account.
If the measured values are more than 2 dB below the levels in the table, the coupler must be replaced.
1145.1155.82
3.93
E-5
Troubleshooting
R&S ZVA
Method 2:
The receiver section of the associated reflectometer is OK.
Loosen the cable at coupler GEN_IN at both ends and screw off at the coupler.
Connect the coupler (connector X1) to a functioning port using the K-cable (ZVA40) or V-cable
(ZVA50).
Set the frequencies and levels listed in the table at the port used for the measurement and measure
the level (wave quantity ax or bx) at the reflectometer associated with the coupler (port) as follows:
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + (linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Frequency
Level
level ax and bx (ZVA40)
level ax and bx (ZVA50)
10 MHz
0 dBm
> -2 dBm
> -2 dBm
100 MHz
0 dBm
> -2 dBm
> -2 dBm
1 GHz
0 dBm
> -2 dBm
> -2 dBm
3 GHz
0 dBm
> -2 dBm
> -2 dBm
8 GHz
0 dBm
> -2 dBm
> -2 dBm
10 GHz
0 dBm
> -2 dBm
> -2 dBm
12 GHz
0 dBm
> -2 dBm
> -2.5 dBm
15 GHz
0 dBm
> -2 dBm
> -2.5 dBm
18 GHz
0 dBm
> -2 dBm
> -2.5 dBm
20 GHz
0 dBm
> -2 dBm
> -2.5 dBm
25 GHz
0 dBm
> -2.5 dBm
> -3 dBm
30 GHz
0 dBm
> -2.5 dBm
> -3 dBm
35 GHz
0 dBm
> -3 dBm
> -3 dBm
40 GHz
0 dBm
> -3 dBm
> -3 dBm
45 GHz
0 dBm
--------
> -3.5 dBm
50 GHz
0 dBm
--------
> -3.5 dBm
With the stated levels, the cable loss must still be taken into account.
If the measured values are more than 2 dB below the levels given in the table, the coupler unit must be
replaced.
1145.1155.82
3.94
E-5
R&S ZVA
Troubleshooting
Coupler Directivity
The following is assumed:
• The generator and receiver sections of the reflectometer associated with the coupler are OK.
Perform a sweep from 10 MHz to 40 GHz, measure Ratio bx/ax Source Portx
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector, save measured values (More Mem :
Data -> Mem3).
Screw the MATCH from the calibration kit to the port connector.
Select User Def Math : linMag(Data) / ((linMag(Mem2) + linMag(Mem3)) / 2 : Math = User Def
The trace gives the directivity.
Frequency range
Directivity
10 MHz to 20 GHz
< -14 dB
20 GHz to 35 GHz
< -10 dB
35 GHz to 40 GHz
< -9 dB
ZVA50 only
35 GHz to 40 GHz
< -8 dB
ZVA50 only
40 GHz to 50 GHz
< -6 dB
If the measured values are more than 2 dB greater than the values stated in the table, the coupler must
be replaced.
Coupler Port Matching
It is assumed that there is a functioning reflectometer in the instrument.
Loosen cables W514A (GEN -> coupler), W515A (coupler -> MEAS) and W518A (coupler -> REF)
at both ends and unscrew at the coupler.
Terminate the coupler input and coupler outputs with three K-terminations (three V-terminations).
Connect test cable to a functioning instrument port and perform a 1-port calibration at the end of the
cable.
Connect the end of the test cable to the port of the coupler under test and display the Sxx
magnitude on the screen.
ZVA50 only
Frequency range
Sxx dB
10 MHz to 5GHz
< -20 dB
5 GHz to 20 GHz
< -15 dB
20 GHz to 30 GHz
< -12 dB
30 GHz to 40 GHz
< -11 dB
40 GHz to 50 GHz
< -10 dB
If the measured values are more than 2 dB greater than the values stated in the table, the coupler must
be replaced.
1145.1155.82
3.95
E-5
Troubleshooting
R&S ZVA
Testing the Reflectometer RM67
Generator levels
It is assumed that the synthesizer section (synthesizer1) associated with the reflectometer to be tested
is OK.
Loosen cable W514A (GEN -> BIAS 67) or W512A (GEN -> attenuator) at both ends and screw off
at the generator output GEN.
Connect the generator output to the spectrum analyzer using the V-cable (if FSU50 or FSU67 is not
available use a power meter for level measurements).
Set the ZVA to the CW sweep mode.
Set the frequencies listed in the table.
Set the power listed in the table.
Frequency
Set power to
(without GenAtt)
Set power to
(with GenAtt)
Level on GEN output
2nd harmonic
10 MHz
10 dBm
9 dBm
13.0 dBm
< - 30 dBm
500 MHz
13 dBm
12 dBm
16.0 dBm
< - 30 dBc
4 GHz
13 dBm
12 dBm
16.4 dBm
< - 30 dBc
8 GHz
13 dBm
12 dBm
16.7 dBm
< - 30 dBc
12 GHz
13 dBm
12 dBm
17.1 dBm
< - 25 dBc
16 GHz
13 dBm
11 dBm
17.4 dBm
< - 25 dBc
20 GHz
13 dBm
11 dBm
17.8 dBm
< - 25 dBc
24 GHz
10 dBm
6 dBm
15.2 dBm
---
28 GHz
10 dBm
7 dBm
15.5 dBm
---
32 GHz
10 dBm
7 dBm
15.9 dBm
---
36 GHz
6 dBm
3 dBm
12.3 dBm
---
40 GHz
6 dBm
3 dBm
12.6 dBm
---
45 GHz
6 dBm
3 dBm
13.1 dBm
---
50 GHz
6 dBm
3 dBm
13.5 dBm
---
55 GHz
2 dBm
- 1 dBm
10.0 dBm
---
60 GHz
2 dBm
- 1 dBm
10.4 dBm
---
67 GHz
2 dBm
- 1 dBm
11.1 dBm
---
With the stated levels, the cable loss must still be taken into account.
1145.1155.82
3.96
E-5
R&S ZVA
Troubleshooting
Receiver levels
The following is assumed:
• The LO synthesizer section associated with the reflectometer to be tested is OK.
• The network controller associated with the reflectometer to be tested is OK.
• One reflectometer in the instrument is functioning.
Loosen the cable to the receiver input MEAS (X6) and the cable to the receiver input REF (X5) at
both ends and screw off at the receiver inputs.
Connect the receiver input (MEAS or REF) to a functioning instrument port using the V-cable.
Set the ZVA to the CW sweep mode.
Set the frequencies and output levels (check with power meter) for the port used for the
measurement as indicated in the table and read off the level for the receiver to be tested (wave
quantity ax or bx).
Frequency
Output level
Displayed level ax
Displayed level bx
(w/o Rec Att)
Displayed level bx
(with Rec Att)
10 MHz
-40 dBm
+16 dBm ± 5 dB
+6 dBm ± 5 dB
+7 dBm ± 4 dB
100 MHz
-40 dBm
-4 dBm ± 4 dB
-14 dBm ± 4 dB
-13 dBm ± 4 dB
1 GHz
-20 dBm
1 dBm ± 4 dB
-9 dBm ± 4 dB
-8 dBm ± 4 dB
3 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-8 dBm ± 4 dB
8 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-8 dBm ± 4 dB
10 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-8 dBm ± 4 dB
12 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-8 dBm ± 4 dB
15 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-7 dBm ± 4 dB
18 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-7 dBm ± 4 dB
20 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-7 dBm ± 4 dB
25 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-6 dBm ± 4 dB
30 GHz
-20 dBm
2 dBm ± 4 dB
-9 dBm ± 4 dB
-6 dBm ± 4 dB
35 GHz
-20 dBm
3 dBm ± 4 dB
-8 dBm ± 4 dB
-5 dBm ± 4 dB
40 GHz
-20 dBm
3 dBm ± 4 dB
-8 dBm ± 4 dB
-5 dBm ± 4 dB
45 GHz
-20 dBm
5 dBm ± 4 dB
-8 dBm ± 4 dB
-5 dBm ± 4 dB
50 GHz
-20 dBm
5 dBm ± 4 dB
-7 dBm ± 4 dB
-4 dBm ± 4 dB
55 GHz
-20 dBm
5 dBm ± 4 dB
-7 dBm ± 4 dB
-4 dBm ± 4 dB
60 GHz
-20 dBm
7 dBm ± 4 dB
-6 dBm ± 4 dB
-3 dBm ± 4 dB
67 GHz
-20 dBm
7 dBm ± 4 dB
-6 dBm ± 4 dB
-3 dBm ± 4 dB
With the stated levels, the cable loss must still be taken into account.
If the measured values are more than 2 dB below the levels list in the table, the board must be
replaced.
1145.1155.82
3.97
E-5
Troubleshooting
R&S ZVA
Coupler levels
The following is assumed:
• One reflectometer in the instrument is OK.
Method 1:
The generator section of the associated reflectometer is OK (output level at the port meets
specifications).
Loosen cable at coupler MEAS_OUT and at coupler REF_OUT at both ends and disconnect at the
coupler.
Connect the coupler output (MEAS = connector X3 or REF = connector X4) to a functioning port.
Terminate the coupler output that is not used.
Set the frequencies and levels listed in the table for the reflectometer associated with the coupler
(port) and measure the level (wave quantity bx) at the port used for the measurement as follows:
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Frequency
Level
Output level MEAS
Output level REF
10 MHz
0 dBm
-46 dBm ± 4 dB
-54 dBm ± 4 dB
100 MHz
0 dBm
-26 dBm ± 4 dB
-34 dBm ± 4 dB
1 GHz
0 dBm
-11 dBm ± 4 dB
-19 dBm ± 4 dB
3 GHz
0 dBm
-11 dBm ± 4 dB
-20 dBm ± 4 dB
8 GHz
0 dBm
-11 dBm ± 4 dB
-19.5 dBm ± 4 dB
10 GHz
0 dBm
-11 dBm ± 4 dB
-19.5 dBm ± 4 dB
12 GHz
0 dBm
-11 dBm ± 4 dB
-19.5 dBm ± 4 dB
15 GHz
0 dBm
-11 dBm ± 4 dB
-19 dBm ± 4 dB
18 GHz
0 dBm
-11 dBm ± 4 dB
-19 dBm ± 4 dB
20 GHz
0 dBm
-11 dBm ± 4 dB
-19 dBm ± 4 dB
25 GHz
0 dBm
-11 dBm ± 4 dB
-19 dBm ± 4 dB
30 GHz
0 dBm
-11 dBm ± 4 dB
-19 dBm ± 4 dB
35 GHz
0 dBm
-12 dBm ± 4 dB
-19.5 dBm ± 4 dB
40 GHz
0 dBm
-12 dBm ± 4 dB
-19.5 dBm ± 4 dB
45 GHz
0 dBm
-12 dBm ± 4 dB
-21 dBm ± 4 dB
50 GHz
0 dBm
-13 dBm ± 4 dB
-21 dBm ± 4 dB
55 GHz
0 dBm
-13 dBm ± 4 dB
-21 dBm ± 4 dB
60 GHz
0 dBm
-14 dBm ± 4 dB
-22.5 dBm ± 4 dB
67 GHz
0 dBm
-14 dBm ± 4 dB
-22 dBm ± 4 dB
With the stated levels, the cable loss must still be taken into account.
If the measured values are more than 2 dB below the levels in the table, the coupler must be replaced.
1145.1155.82
3.98
E-5
R&S ZVA
Troubleshooting
Method 2:
The receiver section of the associated reflectometer is OK.
Loosen the cable at coupler GEN_IN at both ends and screw off at the coupler.
Connect the coupler (connector X1) to a functioning port.
Set the frequencies and levels listed in the table at the port used for the measurement and measure
the level (wave quantity ax or bx) at the reflectometer associated with the coupler (port) as follows:
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector.
Select User Def Math : (lin Mag(Data) + linMag(Mem2)) / 2 , activate Result is Wave Quantity
Select Math = User Def
Frequency
Level
level ax and bx
10 MHz
0 dBm
> -2 dBm
100 MHz
0 dBm
> -2 dBm
1 GHz
0 dBm
> -2 dBm
3 GHz
0 dBm
> -2.1 dBm
8 GHz
0 dBm
> -2.3 dBm
10 GHz
0 dBm
> -2.4 dBm
12 GHz
0 dBm
> -2.5 dBm
15 GHz
0 dBm
> -2.6 dBm
18 GHz
0 dBm
> -2.7 dBm
20 GHz
0 dBm
> -2.8 dBm
25 GHz
0 dBm
> -3 dBm
30 GHz
0 dBm
> -3.2 dBm
35 GHz
0 dBm
> -3.4 dBm
40 GHz
0 dBm
> -3.6 dBm
45 GHz
0 dBm
> -3.8 dBm
50 GHz
0 dBm
> -4 dBm
55 GHz
0 dBm
> -4.2 dBm
60 GHz
0 dBm
> -4.4 dBm
67 GHz
0 dBm
> -4.7 dBm
With the stated levels, the cable loss must still be taken into account.
If the measured values are more than 2 dB below the levels given in the table, the coupler unit must be
replaced.
1145.1155.82
3.99
E-5
Troubleshooting
R&S ZVA
Coupler Directivity
The following is assumed:
• The generator and receiver sections of the reflectometer associated with the coupler are OK.
Perform a sweep from 10 MHz to 67 GHz, measure Ratio bx/ax Source Portx
Screw the SHORT from the calibration kit to the port connector, save measured values (Data ->
Mem).
Screw the OPEN from the calibration kit to the port connector, save measured values (More Mem :
Data -> Mem3).
Screw the MATCH from the calibration kit to the port connector.
Select User Def Math : linMag(Data) / (linMag(Mem2) + linMag(Mem3)) / 2 : Math = User Def
The trace gives the directivity.
Frequency range
Directivity
10 MHz to 20 GHz
< -14 dB
20 GHz to 35 GHz
< -10 dB
35 GHz to 40 GHz
< -8 dB
40 GHz to 50 GHz
< -6 dB
50 GHz to 67 GHz
< -3 dB
If the measured values are more than 2 dB greater than the values stated in the table, the coupler must
be replaced.
Coupler Port Matching
It is assumed that there is a functioning reflectometer in the instrument.
Loosen cables W514A (GEN -> coupler), W515A (coupler -> MEAS) and W518A (coupler -> REF)
at both ends and unscrew at the coupler.
Terminate the coupler input and coupler outputs with three K-terminations (three V-terminations).
Connect test cable to a functioning instrument port and perform a 1-port calibration at the end of the
cable.
Connect the end of the test cable to the port of the coupler under test and display the Sxx
magnitude on the screen.
Frequency range
Sxx dB
10 MHz to 5GHz
< -20 dB
5 GHz to 20 GHz
< -15 dB
20 GHz to 30 GHz
< -12 dB
30 GHz to 40 GHz
< -11 dB
40 GHz to 60 GHz
< -10 dB
60 GHz to 67 GHz
< -6 dB
If the measured values are more than 2 dB greater than the values stated in the table, the coupler must
be replaced.
1145.1155.82
3.100
E-5
R&S ZVA
Troubleshooting
Testing the Network Controller Board
Testing the IF inputs
It is assumed that there is one functioning reflectometer in the instrument.
Disconnect the IF-MEAS and IF-REF cable from each of the reflectometers.
Connect the input to be tested at the end of the appropriate IF cable (W136, W137, W138, W139,
and W146, W147, W148, W149) to a functioning port using the adapter cable and SMA-N adapter .
Set the ZVA to CW sweep mode, CENTER 17.512345 MHz.
Setting at the port used for the measurement: POWER -10 dBm
Setting at the port associated with the network controller under test: WAVE QUANTITY ax or bx.
Enter service function 2.21.2.18.17512345 (IF = 17.512345 MHz).
Disable level corrections with SF 2.21[..24].2.15.1
If the level displayed on the ZVA's screen is not within the range -4 dBm ± 2 dB, the board must be
replaced.
1145.1155.82
3.101
E-5
Troubleshooting
R&S ZVA
Testing the Motherboard
28 V supply
Using a multimeter, measure the voltage at X 100.B5 (wrt ground).
Permissible deviation: ± 0.5 V
Preamplifier for DC measurement inputs
Apply the DC voltages listed in the table using the 4-pin Mini-DIN connector at the DC measurement
input.
Measure the DC voltage with a multimeter.
Input
Voltage
at
Gnd
APPLIED
VOLTAGE
Measurement at
Rated value
DC MEAS -1 V to +1 V
8
3, 5, 6
-1V
X 141.B10
2.33 V
DC MEAS -1 V to +1 V
6
3, 5, 8
+1V
X 141.B11
2.33 V
DC MEAS -10 V to +10 V
8
3, 5, 6
- 10 V
X 141.D10
2.33 V
DC MEAS -10 V to +10 V
6
3, 5, 8
+ 10 V
X 141.D11
2.33 V
Pin assignment DC MEAS connector
If the measured value is more than 10% above or more than 10% below the stated nominal value, the
motherboard must be replaced.
1145.1155.82
3.102
E-5
R&S ZVA
Table of Contents - Software Update / Installation of Options
Table of Contents- Chapter 4 "Software Update / Installation of Options"
4 Software Update / Installation of Options ......................................................... 4.1
Installing new R&S ZVA Software...................................................................................................4.1
Installing Options .............................................................................................................................4.2
1145.1155.82
I-4.1
E-5
Table of Contents - Software Update / Installation of Options
R&S ZVA
This page has been left blank intentionally.
1145.1155.82
I-4.2
E-5
R&S ZVA
4
Installing new R&S ZVA Software
Software Update / Installation of Options
Chapter 4 provides information on updating software, restoring the operating system installation and
installing options. Descriptions accompanying the software update or the options can be included in this
folder as part of Chapter 4.
Installing new R&S ZVA Software
The instrument firmware can be downloaded from the R&S website (www.rohde-schwarz.com). This is a
Microsoft Installation file (.MSI). The file name is ZVAB_XX_YY.MSI for a released version and
ZVAB_XX_YY_BETAZZ.MSI for a test version. This file must be made available to the instrument via a
suitable medium (Memory Stick, USB CD-ROM drive network or Remote Desktop). The instrument
firmware is installed when you double click on the file. The instrument is ready for operation after you
switch off and then switch back on again.
1145.1155.82
4.1
E-5
R&S ZVA
Installing Options
Installing Options
The following options can be fitted to the R&S ZVA:
Direct Generator/Receiver Access
for R&S ZVA8 with two ports
for R&S ZVA8 with four ports
for R&S ZVA24 with two ports
for R&S ZVA24 with four ports
for R&S ZVA40 with two ports
for R&S ZVA40 with four ports
for R&S ZVA50 with two ports
for R&S ZVA50 with four ports
for R&S ZVA67 with two ports
for R&S ZVA67 with four ports
R&S R&S ZVA8-B16
R&S R&S ZVA8-B16
R&S R&S ZVA24-B16
R&S R&S ZVA24-B16
R&S R&S ZVA40-B16
R&S R&S ZVA40-B16
R&S R&S ZVA50-B16
R&S R&S ZVA50-B16
R&S R&S ZVA67-B16
R&S R&S ZVA67-B16
1164.0209.08
1164.0209.10
1164.0209.24
1164.0209.26
1164.0209.40
1164.0209.42
1164.0209.50
1164.0209.52
1164.0209.67
1164.0209.69
Generator Step Attenuator Port 1
for R&S ZVA8
for R&S ZVA24
for R&S ZVA40
for R&S ZVA50
for R&S ZVA67
R&S R&S ZVA8-B21
R&S R&S ZVA24-B21
R&S R&S ZVA40-B21
R&S R&S ZVA50-B21
R&S R&S ZVA67-B21
1164.0009.02
1164.0109.02
1302.5409.02
1305.5616.02
1305.7077.02
Generator Step Attenuator Port 2
for R&S ZVA8
for R&S ZVA24
for R&S ZVA40
for R&S ZVA50
for R&S ZVA67
R&S R&S ZVA8-B22
R&S R&S ZVA24-B22
R&S R&S ZVA40-B22
R&S R&S ZVA50-B22
R&S R&S ZVA67-B22
1164.0015.02
1164.0115.02
1302.5415.02
1305.5622.02
1305.7083.02
Generator Step Attenuator Port 3
for R&S ZVA8 with four ports
for R&S ZVA24 with four ports
for R&S ZVA40 with four ports
for R&S ZVA50 with four ports
for R&S ZVA67 with four ports
R&S R&S ZVA8-B23
R&S R&S ZVA24-B23
R&S R&S ZVA40-B23
R&S R&S ZVA50-B23
R&S R&S ZVA67-B23
1164.0021.02
1164.0121.02
1302.5421.02
1305.5639.02
1305.7090.02
Generator Step Attenuator Port 4
for R&S ZVA8 with four ports
for R&S ZVA24 with four ports
for R&S ZVA40 with four ports
for R&S ZVA50 with four ports
for R&S ZVA67 with four ports
R&S R&S ZVA8-B24
R&S R&S ZVA24-B24
R&S R&S ZVA40-B23
R&S R&S ZVA50-B23
R&S R&S ZVA67-B23
1164.0038.02
1164.0138.02
1302.5438.02
1305.5645.02
1305.7102.02
1145.1155.82
4.2
E-5
R&S ZVA
Installing Options
Receiver Step Attenuator Port 1
for R&S ZVA8
for R&S ZVA24
for R&S ZVA40
for R&S ZVA50
for R&S ZVA67
R&S R&S ZVA8-B31
R&S ZVA24-B31
R&S ZVA40-B31
R&S ZVA50-B31
R&S ZVA67-B31
1164.0044.02
1164.0144.02
1302.5444.02
1305.5716.02
1305.7119.02
Receiver Step Attenuator Port 2
for R&S ZVA8
for R&S ZVA24
for R&S ZVA40
for R&S ZVA50
for R&S ZVA67
R&S ZVA8-B32
R&S ZVA24-B32
R&S ZVA40-B32
R&S ZVA50-B32
R&S ZVA67-B32
1164.0050.02
1164.0150.02
1302.5450.02
1305.5722.02
1305.7125.02
Receiver Step Attenuator Port 3
for R&S ZVA8 with four ports
for R&S ZVA24 with four ports
for R&S ZVA40 with four ports
for R&S ZVA50 with four ports
for R&S ZVA67 with four ports
R&S ZVA8-B33
R&S ZVA24-B33
R&S ZVA40-B33
R&S ZVA50-B33
R&S ZVA67-B33
1164.0067.02
1164.0167.02
1302.5467.02
1305.5739.02
1305.7131.02
Receiver Step Attenuator Port 4
for R&S ZVA8 with four ports
for R&S ZVA24 with four ports
for R&S ZVA40 with four ports
for R&S ZVA50 with four ports
for R&S ZVA67 with four ports
R&S ZVA8-B34
R&S ZVA24-B34
R&S ZVA40-B34
R&S ZVA50-B34
R&S ZVA67-B34
1164.0073.02
1164.0173.02
1302.5473.02
1305.5745.02
1305.7148.02
Oven Controlled Crystal Oscillator (OCXO)
R&S ZVAB-B4
1164.1757.02
Time Domain
R&S ZVAB-K2
1164.1657.02
Frequency Conversion
R&S ZVAB-K4
1164.1863.02
True Differencial Mode
R&S ZVAB-K6
1164.1540.02
Pulsed Measurements
R&S ZVAB-K7
1164.1511.02
Pulsed Measurements with increased recording time for
2-port models
R&S ZVAB-B7
1164.1492.02
Pulsed Measurements with increased recording time for
4-port models
R&S ZVAB-B7
1164.1492.03
1145.1155.82
4.3
E-5
R&S ZVA
Installing Options
Mixer Delay w/o LO Access
R&S ZVAB-K9
1311.3128.0
5 MHz Receiver Bandwidth
R&S ZVAB-K17
1164.1070.02
Internal Pulse Generators
R&S ZVAB-K27
1164.1892.02
Install according to the instructions that are supplied with the option.
These installation instructions can be appended to this chapter.
The OCXO option is permanently integrated on the frequency reference board (mod. 03, mod. 05) and,
as a rule, it is specified when the instrument is ordered. When it is retrofitted, the frequency reference
board must be replaced (replace mod. 02 or mod. 04 with mod. 05).
Installing hardware options:
Risk of Electrostatic Discharge
Disconnect the instrument from the mains before opening the casing. Also note the
safety instructions at the beginning of this manual.
The components used in the instrument are sensitive to electrostatic discharges which
is why they are to be dealt with according to the ESD regulations.
Turn off the instrument and disconnect the mains cable.
Unscrew the 4 back-panel feet (460) and pull off the enclosure (400) towards the rear.
Follow the replacement instructions in Chapter 3
When installation has been completed, push the enclosure back into position and refit the back-panel
feet.
Risk of cable damage
When replacing the tube, be sure not to damage or pull off cables.
Connect the mains cable and turn on the instrument.
1145.1155.82
4.4
E-5
R&S ZVA
Contents - Documents
Contents - Chapter 5 "Documents"
5 Documents..............................................................................................................5. 3
Spare Parts...........................................................................................................................................5.3
Available Power Cables...............................................................................................................5.3
Spare Parts List ...................................................................................................................................5.5
Mechanical Drawings ..........................................................................................................................5.5
Circuit Diagram..................................................................................................................................5.36
Figures
--
Table 5-1
Table 5-2
1145.1078.02
List of power cables available ..............................................................................................5.3
List of all R&S ZVA parts and spare parts............................................................................5.7
I-5.1
E-5
Shipping of Instrument and Ordering of Spare Parts
R&S ZVA
This page is left blank intentionally.
1145.1078.02
I-5.2
E-5
R&S ZVA
Spare Parts
5 Documents
This chapter contains the spare parts list and the documents for the complete R&S ZVA unit. For
general information about spare parts for our products please refer to the sheet "Procedure in Case
of Service and Ordering of Spare Parts" at the beginning of this manual
Spare Parts
The stock numbers necessary for ordering replacement parts and modules can be found in the component lists further down.
Important Note
When replacing a module please note the safety instructions and the repair instructions given in chapter 3 and at the beginning of this service manual
When shipping a module be careful to provide for sufficient mechanical and antistatical protection.
Available Power Cables
Table 5-1 List of power cables available
Stock No.
Earthed-contact connector
Preferably used in
DS 006.7013
BS1363: 1967' complying with
IEC 83: 1975 standard B2
Great Britain
DS 006.7020
Type 12 complying with SEV-regulation
1011.1059, standard sheet S 24 507
Switzerland
DS 006.7036
Type 498 / 13 complying with
US-regulation UL 498, or with IEC 83
USA / Canada
DS 006.7107
Type SAA3 10 A, 250 V,
complying with AS C112-1964 Ap.
Australia
DS 0025.2365
DS 0099.1456
DIN 49 441, 10 A, 250 V, angular
DIN 49 441, 10 A, 250 V, straight
Europe (except Switzerland)
1145.1078.02
5.3
E-5
Spare Parts
1145.1078.02
R&S ZVA
5.4
E-5
Spare Parts List
Mechanical Drawings
1145.1078.02
5.5
E-5
List of ZVB parts including spare parts
R&S ZVA
This page is left blank intentionally.
1145.1078.02
5.6
E-5
R&S ZVA
List of ZVA parts including spare parts
List of Receiver parts including spare parts
The R&S ZVA is constructed in accordance with R&S design 2000.
Overall dimension:
Rackmount:
Accessories:
B x H x T: 465.1 x 286.2 x 417.0
6E 1/1 T350 MOD. 22
19'' Adapter ZZA-611, Stock No. 1096.3302.00
The recommended spare parts are marked with an x in the like column.
Table 5-2 List of all R&S ZVA parts and spare parts.
Position
Designation
Stock No.
Number
Electrical
Designation
Recommended
Spare Parts
DRAWING 1145.1110.01 (R&S ZVA NETWORK ANALYZER)
10
ZM FUNDAMENTAL UNIT ZVA
Model 08 09 10
1145.1310.08
1
12
ZM FUNDAMENTAL UNIT ZVA
Model 24 25 26
1145.1310.24
1
14
ZM FUNDAMENTAL UNIT ZVA
Model 40 41 42 43 45 50 51 52
1145.1310.40
1
15
ZM FAN ZVB
Mounted in frame 1145.1355.00
1145.2200.00
0
E1 E2 E3
x
100
ZE NETWORK CONTROLLER
1145.3635.02
1
A140
x
105
ZE NETWORK CONTROLLER
Model 09 10 25 26 41 42 45 51 52
1145.3635.02
1
A130
x
110
EE SYNTH-LS
Model 08 24
1302.4025.02
1
A160
x
111
EE SYNTH-LS
Model 40 43 50
1302.4025.20
1
A160
x
113
EE SYNTH-DS
Model 09 10 25 26 41 42 45 51 52
1302.5180.02
1
A160
x
115
EE SYNTH-LO
Model 09 10 25 26
1302.4248.02
1
A150
x
116
EE SYNTH-L0
Model 41 42 45 51 52
1302.4248.20
1
A150
x
120
EE FREQ. REFERENCE
1145.3835.04
1
A100
x
121
EE PCI BALANCE
(not used if motherboard 1305.3007.02 is
installed)
1300.1687.02
1
A199
x
130
ED PORT BIAS
1145.3935.02
1
A18
1145.1078.02
5.7
E-5
List of ZVA parts including spare parts
Position
R&S ZVA
Designation
Stock No.
Number
Electrical
Designation
135
ED PORT BIAS
Model 09 10 25 26 41 42 45 51 52
1145.3935.02
1
A19
140
MZ MOTHERB. RAIL 1 ZVA
1145.2168.00
1
141
VS 965/ISR-M2.5X6-A4-PA
1148.3288.00
4
142
VS 6900/ISR-M2.5X8-A2
0041.1653.00
1
143
MZ RAIL CONTACT ZVB 8/20
1300.0874.00
1
145
ZN MOTHERB. RAIL 2 ZVA
1145.2051.00
1
146
VS 965/ISR-M2.5X6-A4-PA
1148.3288.00
4
147
VS 6900/ISR-M2.5X8-A2
0041.1653.00
1
150
ZM RM UNIT ZVA 8
Model 08
1145.4177.02
2
151
VS 6900/ISR-M2.5X6-A2
Model 08
1148.3059.00
4
152
ZM CABLE SET ZVA8 2PORT
Model 08
1302.5050.08
1
153
VS 965/ISR-M2.5X8-A4-PA
Model 08
1148.3294.00
4
154
VS 965/ISR-M2.5X6-A4-PA
Model 08
1148.3288.00
8
155
ZM RM UNIT ZVA 8GHz
Model 09
1145.4177.02
156
VS 6900/ISR-M2.5X6-A2
Model 09
1148.3059.00
6
157
ZM CABLE SET ZVA
Model 09
1145.5050.09
1
158
VS 965/ISR-M2.5X8-A4-PA
Model 09
1148.3294.00
6
159
VS 965/ISR-M2.5X6-A4-PA
Model 09
1148.3288.00
12
160
ZM RM UNIT ZVA 8GHz
Model 10
1145.4177.02
4
161
VS 6900/ISR-M2.5X6-A2
Model 10
1148.3059.00
8
162
ZM CABLE SET ZVA
Model 10
1145.5050.10
1
163
VS 965/ISR-M2.5X8-A4-PA
Model 10
1148.3294.00
8
164
VS 965/ISR-M2.5X6-A4-PA
Model 10
1148.3288.00
16
1145.1078.02
3
5.8
Recommended
Spare Parts
A510 A520
A510 A520
A530
A510 A520
A530 A540
E-5
R&S ZVA
Position
List of ZVA parts including spare parts
Designation
Stock No.
DW RF CABLE W509/A520
Model 08 09 10
1145.3041.00
167
MZ EXT. ANALYZER MOUNT
Model 08 09 10
1145.3058.00
1
168
VS 965/ISR-M2.5X6-A4-PA
Model 08 09 10
1148.3288.00
4
170
ZN MOTHERB. RAIL 2 ZVA
1145.2051.00
1
171
VS 965/ISR-M2.5X6-A4-PA
1148.3288.00
4
172
VS 6900/ISR-M2.5X8-A2
0041.1653.00
1
180
ZE RM UNIT ZVA 24 GHz
Model 24
1145.4302.02
2
182
VS 965/ISR-M3X8-A4-PA
Model 24
1300.0868.00
8
185
ZM CABLE SET ZVA24 2PORT
Model 24
1302.5050.24
1
186
VS 965/ISR-M2.5X6-A4-PA
Model 24
1148.3288.00
8
190
ZE RM UNIT ZVA 24 GHz
Model 25
1145.4302.02
3
192
VS 965/ISR-M3X8-A4-PA
Model 25
1300.0868.00
12
195
ZM CABLE SET ZVA
Model 25
1145.5050.25
1
196
VS 965/ISR-M2.5X6-A4-PA
Model 25
1148.3288.00
12
200
ZE RM UNIT ZVA 24 GHz
Model 26
1145.4302.02
202
VS 965/ISR-M3X8-A4-PA
Model 26
1148.2798.00
16
205
ZM CABLE SET ZVA
Model 26
1145.5050.26
1
206
VS 965/ISR-M2.5X6-A4-PA
Model 26
1148.3288.00
16
207
ZM RM UNIT2 ZVA40 GHz
Model 43 45, Port1 and 2 2.4 mm
1305.3420.12
2
A510 A520
208
ZM RM UNIT2 ZVA40 GHz
Model 43 45, Port3 and 4 2.4 mm
1305.3420.13
2
A530 A540
209
ZM RM UNIT2 ZVA40 GHz
Model 40
1305.3420.02
2
A510 A520
1302.5621.00
0
166
210
MZ RM44 BLOWER ATTACHEMENT
(included in RM Unit ZVA40)
Model 40 41 42 4345 50 51 52
1145.1078.02
Number
Electrical
Designation
Recommended
Spare Parts
W509
1
4
5.9
A510 A520
A510 A520
A530
A510 A520
A530 A540
E-5
List of ZVA parts including spare parts
Position
R&S ZVA
Designation
Stock No.
Number
211
VS 965ISR-M2.5X6-A4-PA
Model 40 41 42 4345 50 51 52
1148.3288.00
4
212
VS 6900/ISR-M2.5X6-A2
Model 40 41 42 4345 50 51 52
1148.3059.00
4
213
MZ RM44 SUPPORT PLATE RM1-2
Model 40 41 42 4345 50 51 52
1302.5596.00
1
214
VS 965ISR-M2.5X6-A4-PA
Model 40 41 42 4345 50 51 52
1148.3288.00
4
215
VS 6900/ISR-M2.5X8-A2
Model 40 41 42 4345 50 51 52
0041.1653.00
2
216
VS 6900/ISR-M2.5X8-A2
Model 40 41 42 50 51 52
0041.1653.00
4
217
VS 965ISR-M3X10-A4-PA
Model 40 43 50
1148.3320.00
8
218
VS 965ISR-M2.5X6-A4-PA
Model 40 43 50
1148.3288.00
4
219
ZM CABLE SET ZVA40 2PORT
Model 40 43
1302.5050.40
1
220
ZM RM UNIT2 ZVA40 GHz
Model 41
1305.3420.02
2
A510 A520
222
ZM RM UNIT2 ZVA40 GHz
Model 41
1305.3420.03
2
A510 A520
223
MZ RM44 SUPPORT PLATE RM3-4
Model 40 41 42 4345 50 51 52
1302.5609.00
1
224
VS 965ISR-M2.5X6-A4-PA
Model 41 42 45 51 52
1148.3288.00
6
226
VS 6900/ISR-M2.5X8-A2
Model 41 51
0041.1653.00
2
227
VS 965ISR-M3X10-A4-PA
Model 41 51
1148.3320.00
12
228
VS 965ISR-M2.5X6-A4-PA
Model 41 51
1148.3288.00
6
229
ZM CABLE SET ZVA40 2PORT
Model 41
1302.5050.41
1
230
ZM RM UNIT2 ZVA40 GHz
Model 42
1305.3420.02
2
A510 A520
232
ZM RM UNIT2 ZVA40 GHz
Model 42
1305.3420.03
2
A530 A540
233
MZ RM44 SUPPORT PLATE RM3-4
Model 42 45 52
1305.3494.00
1
234
VS 965ISR-M2.5X6-A4-PA
1148.3288.00
4
1145.1078.02
5.10
Electrical
Designation
Recommended
Spare Parts
E-5
R&S ZVA
Position
List of ZVA parts including spare parts
Designation
Stock No.
Number
Electrical
Designation
Recommended
Spare Parts
Model 42 45 52
236
VS 6900/ISR-M2.5X8-A2
Model 42 45 52
0041.1653.00
2
237
VS 965ISR-M3X10-A4-PA
Model 42 45 52
1148.3320.00
16
238
VS 965ISR-M2.5X6-A4-PA
Model 42 45 52
1148.3288.00
6
239
ZM CABLE SET ZVA40 2PORT
Model 42 45
1302.5050.42
1
240
ZM RM UNIT ZVA 50 GHz
Model 50
1305.3407.02
2
241
ZM CABLE SET ZVA50 2PORT
Model 42 45
1302.5050.50
1
242
ZM RM UNIT ZVA 50 GHz
Model 51
1305.3407.02
2
A510 A520
243
ZM RM UNIT ZVA 50 GHz
Model 51
1305.3407.03
1
A530
244
ZM CABLE SET ZVA50 3PORT
Model 42 45
1302.5050.51
1
245
ZM RM UNIT ZVA 50 GHz
Model 52
1305.3407.02
2
A510 A520
246
ZM RM UNIT ZVA 50 GHz
Model 52
1305.3407.03
2
A530 A540
247
ZM CABLE SET ZVA50 4PORT
Model 42 45
1302.5050.52
1
260
KB COVER PLATE ZVA
1145.3029.00
1
261
VS 6900/ISR-M2.5X6-A2
1148.3059.00
12
262
ZN COVER HOLDING
1300.0974.00
2
263
VS 965/ISR-M2.5X4-A4-PA
1148.3271.00
4
264
KB REAR PLATE
1145.1861.00
1
265
VS 6900/ISR-M2.5X6-A2
1148.3059.00
5
270
FT ADAPTER 8PINS
1093.9122.00
2
272
SILICONE CORD 4X8 mm
1130.0164.00
2
275
LAN CABLE WITH SPRING
1166.1819.00
2
W241 W242
280
IEC-BUS CABLE W21
1129.7252.00
1
W21
282
WASHER DIN125-A3.2-A4
0082.4670.00
2
284
WAVE SPRING WASHER DIN137-A3-A2
0005.0296.00
2
1145.1078.02
5.11
A510 A520
X241 X242
E-5
List of ZVA parts including spare parts
Position
R&S ZVA
Designation
Stock No.
Number
286
VS DIN934-M3-A4
0016.4398.00
2
287
COVER 30X20 SW
1093.9051.00
2
288
COVER 30X20 SW
1093.9051.00
1
289
COVER 30X20 SW
1093.9051.00
1
290
MP COVER 25PIN SUB-D
1093.9000.00
1
291
MP COVER FOR IEC-BUS
0852.0450.00
1
292
MP CAP
0570.5187.00
2
293
MP CAP
0344.4591.00
2
294
MP CAP
0009.9217.00
1
295
MP ADHESIVE FOIL 33X68
1300.0597.00
4
296
MZ TOP COVER ZVA
1145.1855.00
1
297
MZ BOTTOM COVER ZVA
1145.1955.00
1
299
VS 6900/ISR-M2.5X6-A2
1148.3059.00
44
300
KB FRONT COVER ZVA 8 2PORT
Model 08
1145.1555.00
1
303
KB FRONT COVER ZVA 8 3PORT
Model 09
1145.1549.00
1
306
KB FRONT COVER ZVA 8 4PORT
Model 10
1145.1503.00
1
310
KB FRONT COVER ZVA24 2PORT
Model 24
1145.2380.00
1
313
KB FRONT COVER ZVA24 3PORT
Model 25
1145.2397.00
1
316
KB FRONT COVER ZVA 24 4PORT
Model 26
1145.1510.00
1
320
KB FRONT COVER ZVA 40
Model 40
1145.1526.00
1
321
KB FRONT COVER ZVA 40 2P 2.4MM
Model 43
1305.5268.00
1
323
KB FRONT COVER ZVA 44 3P
Model 41
1302.4860.00
1
326
KB FRONT COVER ZVA 44 4P
Model 42
1302.4877.00
1
327
KB FRONT COVER ZVA 44 4P 2.4MM
Model 45
1305.5274.00
1
1305.3388.00
1
330
KB FRONT COVER ZVA 50 2P
Model 50
1145.1078.02
5.12
Electrical
Designation
Recommended
Spare Parts
E-5
R&S ZVA
Position
List of ZVA parts including spare parts
Designation
Stock No.
Number
Electrical
Designation
Recommended
Spare Parts
334
KB FRONT COVER ZVA 50 4P
Model 52
1305.3394.00
1
390
KB COUNTERSUNK SCREW M1.6X3
LIGHT-GREY
0396.1070.00
1
400
KR TUBE 6HU1/1T450 ZVA
1305.3442.00
1
x
405
KR HOLDING HOOK
1096.4796.00
6
x
410
KR BW2 FRONT HANDLE 6E
1096.1500.00
2
x
420
VS SCREW M4X14-ISR
1096.4896.00
6
430
KR BW2 INSTRUMENT FOOT
1096.2506.00
4
x
440
KR BW2 MOUNTING FOOT
1096.2529.00
2
x
450
KR BW2 SIDE CARRYING HANDLE T450
1096.2670.00
1
x
455
VS 965/ISR-M4X12-A4-PA
1148.2830.00
4
460
KR BW2 REAR PANEL FOOT
1096.2487.00
4
470
OS BW2 REAR PANEL FOOT LABEL
1096.2435.00
1
471
FJ CAP
Model 08
0092.6375.00
2
472
FJ CAP
Model 09
0092.6375.00
3
473
FJ CAP
Model 10
0092.6375.00
4
490
FJ CAP
Model 24 40 43 50
0114.1770.00
2
492
FJ CAP
Model 26 42 45 52
0114.1770.00
4
x
DRAWING 1305.7002.01 (R&S ZVA67 NETWORK ANALYZER)
30
ZM FUNDAMENTAL UNIT ZVA
1145.1310.42
1
40
ZM FAN ZVB
Mounted in frame 1145.1355.00
1145.2200.00
0
50
VS 7985/SR-M4X8-A4-PA
1148.2652.00
0
60
VS DIN433-4.3-A4
0082.4586.00
0
70
ZE NETWORK CONTROLLER
Model 02 04
1145.3635.04
80
ZE NETWORK CONTROLLER
Model 02 04
90
EE SYNTH-12
1145.1078.02
E1 E2 E3
x
1
A140
x
1145.3635.04
1
A130
x
1305.3020.02
1
A150
x
5.13
E-5
List of ZVA parts including spare parts
Position
Designation
R&S ZVA
Stock No.
Number
Electrical
Designation
Recommended
Spare Parts
EE SYNTH-12
Model 04
1305.3020.02
1
A160
x
EE FREQ. REFERENCE
1145.3835.04
1
A100
x
130
ED PORT BIAS
1145.3935.02
1
A18
140
FJ HEX 14 NUT 1/-28UNEF (for A18)
3583.1578.00
2
150
SERRATED LOCKWASHER (for A18)
3583.1578.00
2
ED PORT BIAS
Model 04
1145.3935.02
1
170
FJ HEX 14 NUT 1/-28UNEF (for A19)
3583.1578.00
2
180
SERRATED LOCKWASHER (for A19)
3583.1578.00
2
190
MZ MOTHERB. RAIL 1 ZVA
1145.2168.00
1
200
VS 965/ISR-M2.5X6-A4-PA
1148.3288.00
4
210
VS 6900/ISR-M2.5X8-A2
0041.1653.00
1
220
MZ RAIL CONTACT ZVB 8/20
1300.0874.00
1
230
MZ RM44 BLOWER ATTACHEMENT (included in RM Unit)
1302.5621.00
240
VS 965/ISR-M2.5X6-A4-PA
1148.3288.00
4
245
VS 6900/ISR-M2.5X6-A2
1148.3059.00
4
250
VS 6900/ISR-M2.5X6-A2
1148.3059.00
4
260
MZ RM44 SUPPORT PLATE RM1-2
1302.5596.00
1
270
VS 6900/ISR-M2.5X8-A2
0041.1653.00
4
275
VS 6900/ISR-M2.5X8-A2
0041.1653.00
2
280
VS 965/ISR-M3X10-A4-PA
1148.3320.00
8
290
VS 965/ISR-M2.5X6-A4-PA
1148.3288.00
4
300
ZM RM UNIT ZVA67
Model 02 04
1305.6241.02
2
310
MZ RM44 SUPPORT PLATE RM3-4
Model 04
1305.3494.00
1
315
MZ RM44 SUPPORT PLATE RM3-4
Model 04
1305.3494.00
1
320
VS 965/ISR-M2.5X6-A4-PA
Model 04
1148.3288.00
4
330
VS 965/ISR-M2.5X6-A4-PA
Model 04
1148.3288.00
8
Model 02 04
100
120
160
1145.1078.02
A19
0
5.14
A510, A520
x
E-5
R&S ZVA
Position
List of ZVA parts including spare parts
Designation
Stock No.
Number
335
VS 965/ISR-M2.5X6-A4-PA
Model 04
1148.3288.00
6
340
VS 965ISR-M3X10-A4-PA
Model 41 51
1148.3320.00
16
345
VS 6900/ISR-M2.5X6-A2
Model 04
1148.3059.00
8
350
ZM RM UNIT ZVA67
Model 04
1305.6241.02
2
360
ZM CABLE SET ZVA50 2PORT
Model 02
1302.5050.50
1
370
ZM CABLE SET ZVA50 4PORT
Model 04
1302.5050.52
1
380
KB COVER PLATE ZVA
1145.3029.00
1
390
VS 6900/ISR-M2.5X6-A2
1148.3059.00
13
400
ZN COVER HOLDING
1300.0974.00
2
410
VS 965/ISR-M2.5X4-A4-PA
1148.3271.00
4
420
KB REAR PANEL PLATE
1145.1226.00
1
421
KB COVER REAR PANEL
1145.1232.00
1
422
VS 6900/ISR-M3X6-A2
0041.1682.00
2
430
VS 6900/ISR-M2.5X6-A2
1148.3059.00
5
440
2XRJ45 COUPLER JACK STRAIGHT
1093.9122.00
2
450
SILICONE CORD
1130.0164.00
2
460
LAN CABLE WITH SPRING
1166.1819.00
2
W241, W242
470
IEC-BUS CABLE W21
1129.7252.00
1
W21
480
WASHER DIN125-A3.2-A4
0082.4670.00
2
490
WAVE SPRING WASHER DIN137-A3-A2
0005.0296.00
2
500
VS DIN934-M3-A4
0016.4398.00
2
510
COVER 30X20 SW
1093.9051.00
2
520
COVER 30X20 SW
1093.9051.00
1
550
MP CAP
0570.5187.00
2
560
MP CAP
0344.4591.00
2
580
MP ADHESIVE FOIL 33X68
1300.0597.00
4
590
MZ TOP COVER ZVA
1145.1855.00
1
1145.1078.02
5.15
Electrical
Designation
Recommended
Spare Parts
A530, A540
x
X241, X242
x
E-5
List of ZVA parts including spare parts
Position
R&S ZVA
Designation
Stock No.
Number
Electrical
Designation
Recommended
Spare Parts
600
MZ BOTTOM COVER ZVA
1145.1955.00
1
610
VS 6900/ISR-M2.5X6-A2
1148.3059.00
44
620
KB FRONT COVER ZVA67 2T
Model 02
1305.7025.00
1
630
KB FRONT COVER ZVA67 4T
Model 04
1305.7048.00
1
640
KB COUNTERSUNK SCREW M1.6X3
LIGHT-GREY
0396.1070.00
1
650
KR TUBE 6HU1/1T450 ZVA
1305.3442.00
1
x
660
KR HOLDING HOOK
1096.4796.00
6
x
670
KR BW2 FRONT HANDLE 6E
1096.1500.00
2
x
680
VS SCREW M4X14-ISR
1096.4896.00
6
690
KR BW2 INSTRUMENT FOOT
1096.2506.00
4
x
700
KR BW2 MOUNTING FOOT
1096.2529.00
2
x
710
KR BW2 SIDE CARRYING HANDLE T450
1096.2670.00
2
x
720
VS 965/ISR-M4X12-A4-PA
1148.2830.00
4
730
KR BW2 REAR PANEL FOOT
1096.2487.00
4
740
OS BW2 REAR PANEL FOOT LABEL
1096.2435.00
1
750
FJ CAP
Model 02 04
0114.1770.00
2
760
FJ CAP
Model 04
0114.1770.00
2
770
ZB ACCESS. ZVA
1145.1149.00
1
x
DRAWING 1145.1310.01 (FUNDAMENTAL UNIT R&S ZVA)
500
ZM METAL FRAME ZVA
1145.1355.00
1
516
ED MOTHERBOARD ZVA
Model 08 24 40 41
1305.6470.02
1
A10
x
517
ED MOTHERBOARD ZVA67
Model 42
1305.6570.02
1
A10
x
520
VS 6900/ISR-M2.5X6-A2
1148.3059.00
17
530
FM LOCKING SCREW H=4.5
1093.9180.00
2
535
VS SCREW M2.5X10 A2
0088.7706.00
0
540
FM LOCKING SCREW M3
0009.6501.00
2
551
EMC GASKET
1300.1806.00
2
1145.1078.02
5.16
E-5
R&S ZVA
Position
List of ZVA parts including spare parts
Designation
Stock No.
Number
552
SERRATED LOCKWASHER
3583.1578.00
3
553
HEX 14 NUT 1/2 -28UNEF
3583.1561.00
3
560
MF COVER
1302.4377.00
1
565
VS 965/ISR-M2.5X16-A4-PA
1148.3313.00
2
570
VS SCREW M2.5X6
0071.7572.00
0
580
GR FRONT MOD. CONTROLLER 7/3
1091.3104.00
1
581
BIOS ZVAB FOR FMR7
1300.1529.00
1
582
LITHIUM BATTERY CR2032
0858.2049.00
0
585
BIOS ZVAB
1145.1190.00
0
590
VS 6900/ISR-M2.5X6-A2
1148.3059.00
9
595
DF CABLE 4X2 AND SHIELDING 630
1145.5115.00
1
596
DZ FEED THROUGH
0099.1440.00
1
598
DZ CABLE TIE
0015.9038.00
4
600
ZM DISPLAY UNIT ZVA
Model 08
1145.1390.08
1
A1
604
ZM DISPLAY UNIT ZVA
Model 24 40 41 42
1145.1390.24
1
A1
610
VS 965/ISR-M2.5X5-A4-PA
1148.2752.00
5
670
GP 3.5 FLOPPY DRIVE SLIM
0048.6638.00
1
680
MZ FLOPPY DRIVE HOLDER
1093.4620.00
1
690
DF FLEX-STRIP CONNECTOR
1091.2066.00
1
700
VS 6900/ISR-M2.5X6-A2
1148.3059.00
2
702
VS 7985/ISR-M2.5X4-A4-PA
1148.2717.00
3
704
VS WASHER DIN127-B2.5-A4
0082.4786.00
3
710
ZE HD WITH FIRMWARE ZVT
1145.1178.03
1
A60
x
715
DY SATA CABLE 265
1091.3440.00
1
W11
x
716
DY SATA POWERCABLE 285
1091.3427.00
1
W13
x
720
MZ DISK HOLDER
1093.4837.00
1
725
VS 965/ISR-M2.5X6-A4-PA
1148.3288.00
2
730
VS 965/ISR-M3X5-A4-PA
1148.2775.00
4
735
ED AC FUSE BOARD
1145.3906.02
1
A21
x
1145.1078.02
5.17
Electrical
Designation
Recommended
Spare Parts
A90
x
x
W12
A30
x
W300
E-5
List of ZVA parts including spare parts
Position
R&S ZVA
Designation
Stock No.
Number
736
MZ PROTECTION COVER
1300.0845.00
1
737
VS 7985/ISR-M3X10-A4-PA
1148.2623.00
1
738
OS LABEL 25MM HIGH-VOLTAGE
FLASH
0042.5169.00
1
Electrical
Designation
Recommended
Spare Parts
x
740
DY CABLE FOR ZVAB POWER SUPPLY
Model 08 24 40 41
1145.5544.00
1
W22
741
DX POWER SUPPLY CABLE 2X6
Model 42
1300.2448.00
1
W20
742
DY CABLE FOR ZVT POWER SUPPLY
Model 42
1145.5544.00
1
W21
745
DX POWER SUPPLY CABLE 6P
Model 08 24 40 41
1145.5515.00
1
W22
746
DX POWER SUPPLY CABLE 4P
Model 42
1300.1941.00
1
W22
750
DX POWER SUPPLY CABLE 8P
Model 08 24 40 41
1145.5521.00
1
W24
751
DX POWER SUPPLY CABLE 8P
Model 42
1300.1987.00
1
W24
754
DX POWER SUPPLY CABLE 10P
Model 42
1300.1993.00
1
W25
755
DX POWER SUPPLY CABLE 10P
1145.5538.00
1
W25
756
VS DIN137-A3-A2
0005.0296.00
8
757
VS DIN137-A4-A2
0005.0315.00
6
758
LOCK WASHER
0016.2820.00
8
759
LOCK WASHER
0016.2837.00
6
760
FN POWER FILTER WITH SWITCH
1145.5067.00
1
765
VS 965/ISR-M3X8-A4-PA
1148.2798.00
2
770
ZE POWER UNIT ZVAB
1145.3893.00
1
771
DZ GROMMET 7X12X16
0099.3520.00
1
772
SCREW
1096.4838.00
2
775
DX PE CABLE
1090.3881.00
1
778
OS LABEL RD11 EARTH SYMBOL
0042.5330.00
2
788
OS LABEL 25MM HIGH-VOLTAGE
FLASH
0042.5169.00
1
789
PROTECTION COVER ZVA
1145.3193.00
1
790
GJ SWITCHING POWER SUPPLY
1145.5238.00
1
1145.1078.02
5.18
x
X200
x
W200
x
W201
A20
E-5
R&S ZVA
Position
List of ZVA parts including spare parts
Designation
AC90-264V
SPARE PART
Stock No.
Number
Electrical
Designation
1145.5473.00
Recommended
Spare Parts
x
791
VS WASHER DIN433-4.3-A4
0082.4586.00
4
792
VS 7985/ISR-M4X8-A4-PA
1148.2652.00
4
794
GJ SWITCHING POWER SUPPLY
Model 42
SPARE PART
1300.2490.00
1
1145.1278.00
797
HS IMAGE SOFTWARE
0048.7540.00
798
HS WINDOWS XP EMBEDDED
1099.8570.00
799
OS BARCODE LABEL
0071.7714.00
A20
x
1
DRAWING 1145.1390.01 (DISPLAY UNIT ZVA)
800
ZM MOUNTING PLATE ZVA 8
1145.1703.00
1
805
ZM MOUNTING PLATE ZVA24
1145.2480.00
1
810
OP SCREENED FILTER GLASS
10 OHM/SQ
1069.2021.00
1
820
EK RF SPRING (169)
1069.3063.00
2
830
EK RF SPRING (225)
1069.3057.00
2
840
MB SCREEN HOLDER
0852.0850.00
4
850
VS 965/ISR-M2.5X5-A4-PA
1148.2752.00
4
855
MM PROTECTIVE COLLAR 9.6X13.9
0852.1234.00
1
860
SF FLEXIBLE SWITCH BOARD
1145.1990.00
1
A16
x
870
SF KEY PAD 68T ZVA
1145.2016.00
1
A15
x
880
ZM SUPPORT PLATE ZVA
1145.1984.00
1
890
VS 965/ISR-M2.5X5-A4-PA
1148.2752.00
16
895
MZ SUPPORT PLATE 2 ZVA
1145.2474.00
1
897
VS 965/ISR-M2.5X5-A4-PA
1148.2752.00
3
905
WW ADHESIVE FOAM RIBBON
0852.1805.00
.77 m
910
BP TFT 800X600X3 10.4INCH
1145.5367.00
1
A70
x
912
MZ DISPLAY COVER
1302.5215.00
1
920
VS 6900/ISR-M2.5X6-A2
1148.3059.00
2
925
VS 6900/ISR-M3.0X6-A2
0041.1682.00
2
930
BP 8MA22368 DC TO AC CONVERTER
1145.5267.00
1
T10
x
1145.1078.02
x
5.19
E-5
List of ZVA parts including spare parts
Position
R&S ZVA
Designation
Stock No.
Number
Electrical
Designation
Recommended
Spare Parts
935
VS DIN125-A2.2-HP
0049.7396.00
2
940
VS 7985/ISR-M2X6-A4-PA
1148.2700.00
2
950
DF CONVERTER CABLE L=330
1145.5215.00
1
W100
x
960
EM ROTARY PULSE GENERATOR 1
(WITH KEY)
0852.2760.00
1
B10
x
980
EM COLLAR
0852.1105.00
1
990
OK KNOB
0852.1086.00
1
1000
MZ HOLDING BRACKET FOR PCB
1302.5873.00
1
1010
VS 965/ISR-M2.5X5-A4-PA
1148.2752.00
2
1020
GR DISPLAY CONNECTION
1300.1741.00
1
A19
1030
DF DISPLAY CABLE NEC-ADAPTER
1302.5396.00
1
W70
x
1040
VS 6900/ISR-M2.5X6-A2
1148.3059.00
2
1050
ED USB BOARD
1305.3207.02
1
A40
x
1070
VS 965/ISR-M2.5X5-A4-PA
1148.2752.00
2
A505
x
E500
x
DRAWING 1145.4177.01 (RM UNIT R&S ZVA 8)
100
ZE RM8 BR UNIT
1145.3593.02
1
160
VS 965/ISR-M2.5X8-A4-PA
1148.3294.00
3
170
MB INTAKE FUNNEL RM8
1145.4583.00
1
180
VS 6900/ISR-M2.5X6-A2
1148.3059.00
2
190
ZE FAN 40x40x10
1145.4590.00
1
192
VS DIN433-3.2-A4
0082.4570.00
4
193
VS DIN128-A3-A2
0005.2499.00
4
194
VS 7985/ISR-M3X16-A4
1145.5021.00
4
200
MZ RM MOUNT ZVA
1145.2068.00
1
210
VS 6900/ISR-M2.5X6-A2
1148.3059.00
4
230
MZ SMA HOLDING ZVA
1145.2022.00
1
240
VS 965/ISR-M2.5X6-A4-PA
1148.3288.00
2
250
OS LABEL RM8
1145.4548.00
1
300
DW CABLE W514 GEN
1145.2616.00
1
W514
310
DW CABLE W515 MEAS
1145.2622.00
1
W515
1145.1078.02
5.20
E-5
R&S ZVA
Position
List of ZVA parts including spare parts
Designation
Stock No.
Number
Electrical
Designation
320
DW CABLE W518 REF
1145.3012.00
1
W518
330
FJ TERMINATION 50OHMS SMA
0249.7823.00
1
510
ZM RM SUBUNIT ZVAB 4/8GHz
1302.4990.08
1
Recommended
Spare Parts
DRAWING 1145.3593.01 (RM8 BR UNIT)
100
MB OUTER CONDUCTOR
1045.8888.00
1
110
ZM INNER CONDUCTOR UNIT
1302.5067.00
1
x
DRAWING 1302.4990.01 (RM SUBUNIT ZVAB 8)
110
ED RM8 GENERATOR
1145.4754.02
1
A504
x
125
ED RM8 RECEIVER 2
1302.5009.08
1
A503
x
130
MN COVER B-SIDE GEN 8GHZ
1145.3670.00
1
140
MN COVER A-SIDE GEN 8GHZ
1302.5096.00
1
150
MN COVER B-SIDE REC 8GHZ
1302.5109.00
1
400
OS BARCODE LABEL FOR PCB
0071.7714.00
1
DRAWING 1145.4302.01 (RM UNIT R&S ZVA 24)
200
ZE REFLECTOMETER 24
1145.4283.02
1
A500
x
220
FJ ADAPTER PC3.5 MALE/MALE
1127.9493.00
1
X2
x
230
ZE COUPLER 24
1162.0701.02
1
A501
x
240
MZ COUPLER HOLDING ZVA
1145.4677.00
1
250
VS 7985/ISR-M2.5X16-A4-PA
1148.2869.00
1
270
MZ SMA HOLDING ZVA24
1145.4660.00
1
275
MZ PLATE RM24
1145.4490.00
1
280
VS 965/ISR-M2.5X6-A4-PA
1148.3288.00
2
300
DW RF CABLE W518 REF
1300.0351.00
1
W518
310
DW RF CABLE W515 MEAS
1300.0368.00
1
W515
320
DW RF CABLE W514 GEN
1300.0374.00
1
W514
330
DV RF CABLE W541
1145.4931.00
1
W541
DRAWING 1145.4283.01 (REFLECTOMETER 24)
20
ED RM24 GENERATOR
1145.4348.02
1
A504
30
ZE GENERATOR 24
1151.6503.02
1
A506
40
MN COVER A-SIDE GEN 24GHZ
1145.4648.00
1
1145.1078.02
5.21
E-5
List of ZVA parts including spare parts
Position
R&S ZVA
Designation
Stock No.
Number
Electrical
Designation
50
ED RM24 RECEIVER
1145.4360.02
1
A503
60
ZE RECEIVER 24
1151.7022.02
1
A507
70
MN COVER B-SIDE REC 24GHZ
1145.4654.00
1
80
MZ RM HOLDING ZVA
1145.2422.00
1
90
VS 965/ISR-M2.5X6-A4-PA
1148.3288.00
16
100
ZE FAN 40x40x20
1145.4619.00
1
110
VS 7985/ISR-M3X25-A4
1148.3007.00
4
120
VS DIN433-3.2-A4
0082.4570.00
4
130
VS DIN128-A3-A2
0005.2499.00
4
140
DY CABLE 26P 1,27 70MM1:1
1145.4831.00
1
W519
Recommended
Spare Parts
E500
x
DRAWING 1145.4319.01 (RM UNIT R&S ZVA40 GHz)
400
ZE REFLECTOMETER ZVA40
1145.4390.02
1
A500
x
430
ZE TEST SET 44
1302.3503.02
1
A501
x
440
MZ COUPLEHOLDER 2 ZVA40
1305.3436.00
1
467
VS 6900/ISR-M2.5X6-A2
1148.3059.00
2
470
MZ SMA-HOLDER ZVA40
1302.5767.00
1
475
VS 965/ISR-M2.5X6-A4-PA
1148.3288.00
1
480
DY CABLE W700
1305.3820.00
1
485
DV RF CABLE
1305.3842.00
1
490
MZ RM44 BLOWER ATTACHEMENT
1302.5621.00
1
500
DW RF CABLE W518A REF
1305.3965.00
1
510
DW RF CABLE W515A MEAS
1305.3959.00
1
520
DW RF CABLE W514A GEN
1305.3942.00
1
600
DW RF CABLE W518B REF
1305.5750.00
1
610
DW RF CABLE W515B MEAS
1305.5744.00
1
620
DW RF CABLE W514B GEN
1305.5738.00
1
DRAWING 1305.3420.01 (RM UNIT 2 R&S ZVA40 GHz)
400
ZE REFLECTOMETER ZVA40
1145.4390.02
1
A500
x
430
ZE COUPLER 44
Model 02 03
1306.7506.02
1
A501
x
1145.1078.02
5.22
E-5
R&S ZVA
Position
List of ZVA parts including spare parts
Designation
Stock No.
Number
Electrical
Designation
Recommended
Spare Parts
431
ZE COUPLER 44
Model 12 13
1306.7506.03
1
A501
x
440
MZ COUPLEHOLDER 2 ZVA40
1302.5773.00
1
445
VS 6900/ISR-M2.5X6-A2
1148.3059.00
2
450
ZE BIAS 44
1304.2007.02
1
460
MZ HOLDER
1304.4651.00
1
470
MZ SMA-HOLDER ZVA40
1302.5767.00
1
480
DY CABLE W700
1305.3820.00
1
W700
485
DV RF CABLE
1305.3842.00
1
W541
490
MZ RM44 BLOWER ATTACHEMENT
Model 02 12
1302.5621.00
1
500
DW RF CABLE W518A REF
Model 02 12
1145.4448.00
1
W518A
510
DW RF CABLE W515A MEAS
Model 02 12
1302.5715.00
1
W515A
520
DW RF CABLE W514A GEN
Model 02 12
1302.5709.00
1
W514A
600
DW RF CABLE W518B REF
Model 03 13
1145.445400
1
W518B
610
DW RF CABLE W515B MEAS
Model 03 13
1302.5744.00
1
W515B
620
DW RF CABLE W514B GEN
Model 03 13
1302.5738.00
1
W514B
x
DRAWING 1305.3407.01 (RM UNIT R&S ZVA50 GHz)
400
ZE REFLECTOMETER R&S ZVA50
1305.3413.02
1
A500
x
430
ZE COUPLER 50
1306.9009.02
1
A501
x
440
MZ COUPLEHOLDER ZVA40
1302.5773.00
1
445
VS 6900/ISR-M2.5X6-A2
1148.3059.00
2
450
ZE BIAS 50
1306.9509.02
1
460
MZ HOLDER
1304.4651.00
1
470
MZ SMA-HOLDER ZVA50
1305.5516.00
1
475
VS 965/ISR-M2.5X6-A4-PA
1148.3288.00
2
480
DY CABLE W700
1305.3820.00
1
W700
485
DV RF CABLE
1305.3842.00
1
W541
1145.1078.02
5.23
x
E-5
List of ZVA parts including spare parts
Position
R&S ZVA
Designation
Stock No.
Number
Electrical
Designation
490
MZ RM44 BLOWER ATTACHEMENT
Model 02
1302.5621.00
1
500
DW RF CABLE W518A REF
Model 02
1305.5245.00
1
W518A
510
DW RF CABLE W515A MEAS
Model 02
1305.5222.00
1
W515A
520
DW RF CABLE W514A GEN
Model 02
1305.5200.00
1
W514A
600
DW RF CABLE W518B REF
Model 03
1305.5252.00
1
W518B
610
DW RF CABLE W515B MEAS
Model 03
1305.5239.00
1
W515B
620
DW RF CABLE W514B GEN
Model 03
1305.5216.00
1
W514B
Recommended
Spare Parts
DRAWING 1305.6241.01 (RM UNIT R&S ZVA67 GHz)
400
ZE REFLECTOMETER ZVA67
1305.6258.02
1
A500
x
430
ZE COUPLER 67
1310.5504.02
1
A501
x
440
MZ COUPLEHOLDER ZVA40
1302.5773.00
1
445
VS 6900/ISR-M2.5X6-A2
1148.3059.00
2
450
ZE MICROSTRIP BIAS 67
1310.4008.02
1
460
MZ HOLDER BIAS67
1305.6464.00
1
470
MZ SMA-HOLDER ZVA50
1305.5516.00
1
475
VS 965/ISR-M2.5X6-A4-PA
1148.3288.00
2
480
DY CABLE W700
1305.3820.00
1
W700
485
DV RF CABLE
1305.3842.00
1
W541
490
MZ RM44 BLOWER ATTACHEMENT
Model 02
1302.5621.00
1
500
DW RF CABLE W518 REF
Model 02
1305.6641.00
1
W518A
510
DW RF CABLE W515 MEAS
Model 02
1305.6670.00
1
W515A
520
DW RF CABLE W514 GEN
Model 02
1305.6664.00
1
W514A
600
DW RF CABLE W518B REF
Model 03
1305.6858.00
1
W518B
610
DW RF CABLE W515B MEAS
Model 03
1305.6864.00
1
W515B
1145.1078.02
5.24
x
x
E-5
R&S ZVA
Position
620
List of ZVA parts including spare parts
Designation
Stock No.
Number
Electrical
Designation
DW RF CABLE W514B GEN
Model 03
1305.6841.00
1
W514B
A100
Recommended
Spare Parts
DRAWING 1164.1770.00 (OPTION ZVAB-B4 1164.1757.02)
20
EE FREQUENCY REFERENCE
1145.3835.05
1
30
PD INSTALLATION INSTRUCTION
ZVAB-B4
1164.1770.00
1
x
DRAWING 1164.0250.00 (OPTION R&S ZVA8-B16 DIRECT GENERATOR/RECEIVER ACCESS 1164.0209.08/09/10)
1120
DW RF CABLE W503 REF OUT
Model 08 09 10
1145.2968.00
2
W503
1122
DW RF CABLE W503 REF OUT
Model 09 10
1145.2968.00
1
W503
1124
DW RF CABLE W503 REF OUT
Model 10
1145.2968.00
1
W503
1130
DW RF CABLE W501 REF IN
Model 08 09 10
1145.2951.00
2
W501
1132
DW RF CABLE W501 REF IN
Model 09 10
1145.2951.00
1
W501
1134
DW RF CABLE W501 REF IN
Model 10
1145.2951.00
1
W501
1140
DW RF CABLE W513 SRC OUT
Model 08 09 10 (only w. Gen Att)
1164.0321.00
2
W513
1142
DW RF CABLE W513 SRC OUT
Model 09 10 (only w. Gen Att)
1164.0321.00
1
W513
1144
DW RF CABLE W513 SRC OUT
Model 10 (only w. Gen Att)
1164.0321.00
1
W513
1145.2997.00
2
1150
DW RF CABLE W534 SRC IN
Model 08 09 10
W534
1152
DW RF CABLE W534 SRC IN
Model 09 10
1145.2997.00
1
W534
1154
DW RF CABLE W534 SRC IN
Model 10
1145.2997.00
1
W534
1160
DW RF CABLE W505 MEAS OUT
Model 08 09 10
1145.2980.00
2
W505
1162
DW RF CABLE W505 MEAS OUT
Model 09 10
1145.2980.00
1
W505
1164
DW RF CABLE W505 MEAS OUT
Model 10
1145.2980.00
1
W505
1170
DW RF CABLE W506 MEAS IN
Model 08 09 10 (only w. Rec Att)
1164.0280.00
2
W506
1172
DW RF CABLE W506 MEAS IN
Model 09 10 (only w. Rec Att)
1164.0280.00
1
W506
1145.1078.02
5.25
E-5
List of ZVA parts including spare parts
Position
1174
1180
R&S ZVA
Designation
Stock No.
Number
Electrical
Designation
DW RF CABLE W506 MEAS IN
Model 10 (only w. Rec Att)
1164.0280.00
1
W506
1145.3006.00
2
W535
DW RF CABLE W535 SRC OUT
Model 08 09 10 (only w. Gen Att or Combiner)
1182
DW RF CABLE W535 SRC OUT
Model 09 10 (only w. Gen Att or Combiner)
1145.3006.00
1
W535
1184
DW RF CABLE W535 SRC OUT
Model 10 (only w. Gen Att or Combiner)
1145.3006.00
1
W535
1190
DW RF CABLE W504 MEAS IN
Model 08 09 10 (only w. Rec Att )
1145.2974.00
2
W504
1192
DW RF CABLE W504 MEAS IN
Model 09 10 (only w. Rec Att )
1145.2974.00
1
W504
1194
DW RF CABLE W504 MEAS IN
Model 10 (only w. Rec Att )
1145.2974.00
1
W504
1200
DW RF CABLE W513 SRC OUT
Model 08 09 10 (only w. Combiner Att )
1300.0480.00
2
W513
1202
DW RF CABLE W513 SRC OUT
Model 09 10 (only w. Combiner Att )
1300.0480.00
1
W513
1204
DW RF CABLE W513 SRC OUT
Model 10 (only w. Combiner Att )
1300.0480.00
1
W513
1210
DW CABLE EXT. 3.6
Model 08 09 10
1300.1729.00
6
W611 W612
W613
W621 W622
W623
1212
DW CABLE EXT. 3.6
Model 09 10
1300.1729.00
3
W631 W632
W633
1214
DW CABLE EXT. 3.6
Model 10
1300.1729.00
3
W641 W642
W643
1215
PD INSTALLATION INSTRUCTION
1164.0250.00
1
Recommended
Spare Parts
DRAWING 1164.0267.00 (OPTION R&S ZVA24-B16 DIRECT GENERATOR/RECEIVER ACCESS 1164.0209.24/25/26)
1220
DW RF CABLE W503 REF OUT
Model 24 25 26
1300.0380.00
2
W503
1222
DW RF CABLE W503 REF OUT
Model 25 26
1300.0380.00
1
W503
1224
DW RF CABLE W503 REF OUT
Model 26
1300.0380.00
1
W503
1230
DW RF CABLE W501 REF IN
Model 24 25 26
1300.0397.00
2
W501
1232
DW RF CABLE W501 REF IN
Model 25 26
1300.0397.00
1
W501
1234
DW RF CABLE W501 REF IN
Model 26
1300.0397.00
1
W501
1145.1078.02
5.26
E-5
R&S ZVA
Position
List of ZVA parts including spare parts
Designation
Stock No.
Number
Electrical
Designation
1240
DW RF CABLE W513 SRC OUT
Model 24 25 26 (only w. Gen Att )
1300.0474.00
2
W513
1242
DW RF CABLE W513 SRC OUT
Model 25 26 (only w. Gen Att )
1300.0474.00
1
W513
1244
DW RF CABLE W513 SRC OUT
Model 26 (only w. Gen Att )
1300.0474.00
1
W513
1250
DW RF CABLE W534 SRC IN
Model 24 25 26
1300.0422.00
2
W534
1252
DW RF CABLE W534 SRC IN
Model 25 26
1300.0422.00
1
W534
1254
DW RF CABLE W534 SRC IN
Model 26
1300.0422.00
1
W534
1260
DW RF CABLE W505 MEAS OUT
Model 24 25 26
1300.0416.00
2
W505
1262
DW RF CABLE W505 MEAS OUT
Model 25 26
1300.0416.00
1
W505
1264
DW RF CABLE W505 MEAS OUT
Model 26
1300.0416.00
1
W505
1270
DW RF CABLE W506 MEAS IN
Model 24 25 26 (only w. Rec Att )
1300.0468.00
2
W506
1272
DW RF CABLE W506 MEAS IN
Model 25 26 (only w. Rec Att )
1300.0468.00
1
W506
1274
DW RF CABLE W506 MEAS IN
Model 26 (only w. Rec Att )
1300.0468.00
1
W506
1280
DW RF CABLE W535 SRC OUT
Model 24 25 26 (only w. Gen Att )
1300.0439.00
2
W535
1282
DW RF CABLE W535 SRC OUT
Model 25 26 (only w. Gen Att )
1300.0439.00
1
W535
1284
DW RF CABLE W535 SRC OUT
Model 26 (only w. Gen Att )
1300.0439.00
1
W535
1290
DW RF CABLE W504 MEAS IN
Model 24 25 26 (only w. Rec Att )
1300.0400.00
2
W504
1292
DW RF CABLE W504 MEAS IN
Model 25 26 (only w. Rec Att )
1300.0400.00
1
W504
1294
DW RF CABLE W504 MEAS IN
Model 26 (only w. Rec Att )
1300.0400.00
1
W504
1300
DW CABLE EXT. (AL3.6 PC3.5)
Model 24 25 26
1145.2580.00
6
W611 W612
W613
W621 W622
W623
1302
DW CABLE EXT. (AL3.6 PC3.5)
Model 25 26
1145.2580.00
3
W631 W632
W633
1304
DW CABLE EXT. (AL3.6 PC3.5)
1145.2580.00
3
W641 W642
1145.1078.02
5.27
Recommended
Spare Parts
x
X
E-5
List of ZVA parts including spare parts
Position
Designation
R&S ZVA
Stock No.
Number
Model 26
1310
PD INSTALLATION INSTRUCTION
Electrical
Designation
Recommended
Spare Parts
W643
1164.0267.00
1
DRAWING 1164.0238.00 (OPTION R&S ZVA40-B16 DIRECT GENERATOR/RECEIVER ACCESS 1164.0209.40/41/42)
1320
DW RF CABLE W503 REF OUT
Model 40 41 42
1145.4525.00
2
W503
1322
DW RF CABLE W503 REF OUT
Model 41 42
1145.4525.00
1
W503
1324
DW RF CABLE W503 REF OUT
Model 42
1145.4525.00
1
W503
1330
DW RF CABLE W501A REF IN
Model 40 41 42
1305.3594.00
2
W501A
1332
DW RF CABLE W501B REF IN
Model 41 42
1305.3620.00
1
W501B
1334
DW RF CABLE W501B REF IN
Model 42
1305.3620.00
1
W501B
1340
DW RF CABLE W513 SRC OUT
Model 40 41 42 (only w. Gen Att )
1300.0474.00
2
W513
1342
DW RF CABLE W513 SRC OUT
Model 41 42 (only w. Gen Att )
1300.0474.00
1
W513
1344
DW RF CABLE W513 SRC OUT
Model 42 (only w. Gen Att )
1300.0474.00
1
W513
1350
DW RF CABLE W534 SRC IN
Model 40 41 42
1305.3542.00
2
W534
1352
DW RF CABLE W534 SRC IN
Model 41 42
1305.3542.00
1
W534
1354
DW RF CABLE W534 SRC IN
Model 42
1305.3542.00
1
W534
1360
DW RF CABLE W505 MEAS OUT
Model 40 41 42
1305.3565.00
2
W505
1362
DW RF CABLE W505 MEAS OUT
Model 41 42
1305.3565.00
1
W505
1364
DW RF CABLE W505 MEAS OUT
Model 42
1305.3565.00
1
W505
1370
DW RF CABLE W506 MEAS IN
Model 40 41 42 (only w. Rec Att )
1300.0468.00
2
W506
1372
DW RF CABLE W506 MEAS IN
Model 41 42 (only w. Rec Att )
1300.0468.00
1
W506
1374
DW RF CABLE W506 MEAS IN
Model 42 (only w. Rec Att )
1300.0468.00
1
W506
1380
DW RF CABLE W535A SRC OUT
Model 40 41 42 (only without Gen Att )
1305.3559.00
2
W535A
1145.1078.02
5.28
E-5
R&S ZVA
Position
List of ZVA parts including spare parts
Designation
Stock No.
Number
Electrical
Designation
1382
DW RF CABLE W535B SRC OUT
Model 41 42 (only without Gen Att )
1305.3607.00
1
W535B
1384
DW RF CABLE W535B SRC OUT
Model 42 (only without Gen Att )
1305.3607.00
1
W535B
1390
DW RF CABLE W504A MEAS IN
Model 49 41 42 (only without Rec Att )
1305.3571.00
2
W504A
1392
DW RF CABLE W504B MEAS IN
Model 41 42 (only without Rec Att )
1305.3613.00
1
W504B
1394
DW RF CABLE W504B MEAS IN
Model 42 (only without Rec Att )
1305.3513.00
1
W504B
1400
DW CABLE EXT. (AL3.6 PC3.5)
Model 40 41 42
1145.2580.00
6
W611 W612
W613
W621 W622
W623
1402
DW CABLE EXT. (AL3.6 PC3.5)
Model 41 42
1145.2580.00
3
W631 W632
W633
1404
DW CABLE EXT. (AL3.6 PC3.5)
Model 42
1145.2580.00
3
W641 W642
W643
1410
PD INSTALLATION INSTRUCTION
1164.0238.00
1
Recommended
Spare Parts
DRAWING 1305.5322.00 (OPTION R&S ZVA50-B16 DIRECT GENERATOR/RECEIVER ACCESS 1164.0209.54/52)
1420
DW RF CABLE W503 REF OUT
Model 50 52
1305.5451.00
2
W503
1424
DW RF CABLE W503 REF OUT
Model 52
1305.5451.00
1
W503
1430
DW RF CABLE W501A REF IN
Model 50 52
1305.5445.00
2
W501A
1434
DW RF CABLE W501B REF IN
Model 52
1305.5480.00
1
W501B
1440
DW RF CABLE W513 SRC OUT
Model 50 52 (only w. Gen Att )
1305.5500.00
2
W513
1444
DW RF CABLE W513 SRC OUT
Model 52 (only w. Gen Att )
1305.5500.00
1
W513
1450
DW RF CABLE W534 SRC IN
Model 50 52
1305.5400.00
2
W534
1454
DW RF CABLE W534 SRC IN
Model 52
1305.5400.00
1
W534
1460
DW RF CABLE W505 MEAS OUT
Model 50 52
1305.5439.00
2
W505
1464
DW RF CABLE W505 MEAS OUT
Model 42
1305.5439.00
1
W505
1470
DW RF CABLE W506 MEAS IN
Model 50 52 (only w. Rec Att )
1305.5497.00
2
W506
1145.1078.02
5.29
E-5
List of ZVA parts including spare parts
Position
R&S ZVA
Designation
Stock No.
Number
Electrical
Designation
1474
DW RF CABLE W506 MEAS IN
Model 52 (only w. Rec Att )
1300.5497.00
1
W506
1480
DW RF CABLE W535A SRC OUT
Model 50 52 (only without Gen Att )
1305.5416.00
2
W535A
1484
DW RF CABLE W535B SRC OUT
Model 52 (only without Gen Att )
1305.5416.00
1
W535B
1490
DW RF CABLE W504A MEAS IN
Model 50 52 (only without Rec Att )
1305.5422.00
2
W504A
1494
DW RF CABLE W504B MEAS IN
Model 52 (only without Rec Att )
1305.5474.00
1
W504B
1500
VS DIN912-M1.6X5-A2
Model 50 52
0920.8428.00
48
1504
VS DIN912-M1.6X5-A2
Model 52
0920.8428.00
48
1510
DW CABLE EXT. (AL3.6 PC3.5)
Model 50 52
1305.5397.00
6
W611 W612
W613
W621 W622
W623
1514
DW CABLE EXT. (AL3.6 PC3.5)
Model 41 42
1305.5397.00
6
W631 W632
W633
W641 W642
W643
1520
PD INSTALLATION INSTRUCTION
1305.5322.00
1
DRAWING
1164.0215.00 (OPTION R&S ZVA8-B21 GEN.ATTENUATOR PORT 1
(OPTION R&S ZVA8-B22 GEN.ATTENUATOR PORT 2
(OPTION R&S ZVA8-B23 GEN.ATTENUATOR PORT 3
(OPTION R&S ZVA8-B24 GEN.ATTENUATOR PORT 4
1164.0009.02)
1164.0015.02)
1164.0021.02)
1164.0038.02)
20
ZE ATTENUATOR COMB 8
1137.1595.02
1
40
VS DIN6900-M2.5X6 -A2
0071.5040.00
2
50
DY ATT-CTRL_CABLE 90
1164.0244.00
1
W550
60
DW RF CABLE W512 ATT-GEN
1164.0315.00
1
W512
70
DW RF CABLE W536 SRC
1164.0367.00
1
W536
80
DW RF CABLE W517 EXT SRC1
1300.0516.00
1
W517
130
PD INSTALLATION INSTRUCTION
1164.0215.00
1
DRAWING
1164.0215.00 (OPTION R&S ZVA8-B31 REC.ATTENUATOR PORT 1
(OPTION R&S ZVA8-B32 REC.ATTENUATOR PORT 2
(OPTION R&S ZVA8-B33 REC.ATTENUATOR PORT 3
(OPTION R&S ZVA8-B34 REC.ATTENUATOR PORT 4
20
ZE ATTENUATOR REC8
1137.1543.02
1
40
VS DIN6900-M2.5X6 -A2
0071.5040.00
2
50
DY ATT-CTRL_CABLE 90
1164.0244.00
1
1145.1078.02
5.30
Recommended
Spare Parts
A550
x
1164.0044.02)
1164.0050.02)
1164.0067.02)
1164.0073.02)
A550
x
W550
E-5
R&S ZVA
Position
List of ZVA parts including spare parts
Designation
Stock No.
Number
Electrical
Designation
70
DW RF CABLE W507 ATT-REC
1164.0296.00
1
W507
80
DW RF CABLE W508 MEAS
1164.0273.00
1
W508
100
PD INSTALLATION INSTRUCTION
1164.0215.00
1
DRAWING
1164.0221.00 (OPTION R&S ZVA24-B21 GEN.ATTENUATOR PORT 1
(OPTION R&S ZVA24-B22 GEN.ATTENUATOR PORT 2
(OPTION R&S ZVA24-B23 GEN.ATTENUATOR PORT 3
(OPTION R&S ZVA24-B24 GEN.ATTENUATOR PORT 4
1164.0109.02)
1164.0115.02)
1164.0121.02)
1164.0138.02)
20
ZE ATTENUATOR GEN24
1046.5082.04
1
30
MZ ATTENUATOR MOUNT ZVA24
1164.0438.00
1
40
VS DIN6900-M2.5X6 -A2
0071.5040.00
3
50
DY ATT-CTRL_CABLE 90
1164.0244.00
1
W550
60
DW RF CABLE W512 ATT-GEN
1300.0451.00
1
W512
70
DW RF CABLE W536 SRC
1164.0380.00
1
W536
120
PD INSTALLATION INSTRUCTION
1164.0221.00
1
DRAWING
1164.0221.00 (OPTION R&S ZVA24-B31 REC.ATTENUATOR PORT 1
(OPTION R&S ZVA24-B32 REC.ATTENUATOR PORT 2
(OPTION R&S ZVA24-B33 REC.ATTENUATOR PORT 3
(OPTION R&S ZVA24-B34 REC.ATTENUATOR PORT 4
A550
x
1164.0144.02)
1164.0150.02)
1164.0167.02)
1164.0173.02)
20
ZE ATTENUATOR REC24
1046.5082.05
1
30
MZ ATTENUATOR MOUNT ZVA24
1164.0438.00
1
40
VS DIN6900-M2.5X6 -A2
0071.5040.00
3
50
DY ATT-CTRL_CABLE 90
1164.0244.00
1
W550
70
DW RF CABLE W507 ATT-REC
1300.0445.00
1
W507
80
DW RF CABLE W508 MEAS
1164.0373.00
1
W508
DRAWING
Recommended
Spare Parts
A550
x
1164.0409.00 (OPTION R&S ZVA40-B21 GEN.ATTENUATOR PORT 1 1302.5409.02)
(OPTION R&S ZVA40-B22 GEN.ATTENUATOR PORT 2 1302.5415.02)
2010
ZE ATTENUATOR GEN44
1046.5082.02
1
2020
VS DIN6900-M2.5X6 -A2
1148.3059.00
2
2030
DY ATT-CTRL_CABLE 90
1164.0244.00
1
W550
2040
DW RF CABLE W512A ATT-GEN
1305.3636.00
1
W512A
2060
DW RF CABLE W536 SRC
1305.3671.00
1
W536
2070
DW RF CABLE W513 SRC OUT
1300.0474.00
1
W513
2090
PD INSTALLATION INSTRUCTION
1164.0409.00
1
1145.1078.02
5.31
A550
x
E-5
List of ZVA parts including spare parts
Position
Designation
DRAWING
R&S ZVA
Stock No.
Number
Electrical
Designation
Recommended
Spare Parts
1164.0409.00 (OPTION R&S ZVA40-B23 GEN.ATTENUATOR PORT 3 1302.5421.02)
(OPTION R&S ZVA40-B24 GEN.ATTENUATOR PORT 4 1302.5438.02)
2010
ZE ATTENUATOR GEN44
1046.5082.02
1
2020
VS DIN6900-M2.5X6 -A2
1148.3059.00
2
2030
DY ATT-CTRL_CABLE GENERATOR 240
MM
1164.0396.00
1
W550
2040
DW RF CABLE W512B ATT-GEN
1305.3659.00
1
W512B
2060
DW RF CABLE W536 SRC
1305.3671.00
1
W536
2070
DW RF CABLE W513 SRC OUT
1300.0474.00
1
W513
2090
PD INSTALLATION INSTRUCTION
1164.0409.00
1
DRAWING
A550
x
1164.0409.00 (OPTION R&S ZVA40-B31 REC.ATTENUATOR PORT 1 1302.5444.02)
(OPTION R&S ZVA40-B32 REC.ATTENUATOR PORT 2 1302.5450.02)
2110
ZE ATTENUATOR REC44
1046.5082.03
1
2120
VS DIN6900-M2.5X6 -A2
1148.3059.00
2
2130
DY ATT-CTRL_CABLE 90
1164.0244.00
1
W550
2140
DW RF CABLE W507A ATT-REC
1305.3642.00
1
W507A
2160
DW RF CABLE W508 MEAS
1305.3688.00
1
W508
2170
DW RF CABLE W506 MEAS IN
1305.0468.00
1
W506
2190
PD INSTALLATION INSTRUCTION
1164.0409.00
1
DRAWING
A550
x
1164.0409.00 (OPTION R&S ZVA40-B33 REC.ATTENUATOR PORT 3 1302.5467.02)
(OPTION R&S ZVA40-B34 REC.ATTENUATOR PORT 4 1302.5473.02)
2110
ZE ATTENUATOR REC44
1046.5082.03
1
2120
VS DIN6900-M2.5X6 -A2
1148.3059.00
2
2130
DY ATT-CTRL_CABLE GENERATOR 240
MM
1164.0396.00
1
W550
2140
DW RF CABLE W507B ATT-REC
1305.3665.00
1
W507B
2160
DW RF CABLE W508 MEAS
1305.3688.00
1
W508
2170
DW RF CABLE W506 MEAS IN
1305.0468.00
1
W506
2190
PD INSTALLATION INSTRUCTION
1164.0409.00
1
DRAWING
A550
x
1164.0409.00 (OPTION R&S ZVA50-B21 GEN.ATTENUATOR PORT 1 1305.5616.02)
(OPTION R&S ZVA50-B22 GEN.ATTENUATOR PORT 2 1305.5622.02)
2010
ZE ATTENUATOR 50 DB
1170.0065.02
1
2020
VS DIN6900-M2.5X6 -A2
1148.3059.00
2
1145.1078.02
5.32
A550
x
E-5
R&S ZVA
Position
List of ZVA parts including spare parts
Designation
Stock No.
Number
Electrical
Designation
2030
DY ATT-CTRL_CABLE 90
1164.0244.00
1
W550
2040
DW RF CABLE W512A ATT-GEN
1305.5345.00
1
W512A
2060
DW RF CABLE W536 SRC
1305.5339.00
1
W536
2070
DW RF CABLE W513 SRC OUT
1305.5500.00
1
W513
2090
PD INSTALLATION INSTRUCTION
1305.5322.00
1
DRAWING
Recommended
Spare Parts
1164.0409.00 (OPTION R&S ZVA50-B23 GEN.ATTENUATOR PORT 3 1305.5639.02)
(OPTION R&S ZVA50-B24 GEN.ATTENUATOR PORT 4 1305.5645.02)
2010
ZE ATTENUATOR 50 DB
1170.0065.02
1
2020
VS DIN6900-M2.5X6 -A2
1148.3059.00
2
2030
DY ATT-CTRL_CABLE 90
1164.0244.00
1
W550
2040
DW RF CABLE W512B ATT-GEN
1305.5351.00
1
W512B
2060
DW RF CABLE W536 SRC
1305.5339.00
1
W536
2070
DW RF CABLE W513 SRC OUT
1305.5500.00
1
W513
2090
PD INSTALLATION INSTRUCTION
1305.5322.00
1
DRAWING
A550
x
1164.0409.00 (OPTION R&S ZVA50-B31 REC.ATTENUATOR PORT 1 1302.5716.02)
(OPTION R&S ZVA50-B32 REC.ATTENUATOR PORT 2 1302.5722.02)
2110
ZE ATTENUATOR 35 DB
1170.0065.03
1
2120
VS DIN6900-M2.5X6 -A2
1148.3059.00
2
2130
DY ATT-CTRL_CABLE 90
1164.0244.00
1
W550
2140
DW RF CABLE W507A ATT-REC
1305.5374.00
1
W507A
2160
DW RF CABLE W508 MEAS
1305.3568.00
1
W508
2170
DW RF CABLE W506 MEAS IN
1305.5497.00
1
W506
2190
PD INSTALLATION INSTRUCTION
1305.5322.00
1
DRAWING
A550
x
1164.0409.00 (OPTION R&S ZVA50-B33 REC.ATTENUATOR PORT 3 1302.5739.02)
(OPTION R&S ZVA50-B34 REC.ATTENUATOR PORT 4 1302.5745.02)
2110
ZE ATTENUATOR 35 DB
1170.0065.03
1
2120
VS DIN6900-M2.5X6 -A2
1148.3059.00
2
2130
DY ATT-CTRL_CABLE 90
1164.0244.00
1
W550
2140
DW RF CABLE W507B ATT-REC
1305.5380.00
1
W507B
2160
DW RF CABLE W508 MEAS
1305.5368.00
1
W508
2170
DW RF CABLE W506 MEAS IN
1305.5497.00
1
W506
2190
PD INSTALLATION INSTRUCTION
1305.5322.00
1
1145.1078.02
5.33
A550
x
E-5
Circuit Diagram
1145.1155.82
5.29
E-4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement