Standard
SPF9 Stapler-Folder
&
FC9 Trimmer
Service Manual
Provided By
http://www.MyBinding.com http://www.MyBindingBlog.com
S ERVICE MANUAL
Standard Horizon SPF-9/FC-9 Stapler-Folder
Fore-Edge Trimmer
SM_SPF9/FC9
Read this manual, and thoroughly familiarize yourself with its contents before operating or servicing this equipment.
STAPLER & FOLDER
FORE-EDGE TRIMMER
SPF-9/FC-9
Important Information
- This manual is designed to help you to maintain and repair Stapler & Folder SPF-9 and
Fore-edge Trimmer FC-9. Read, understand and keep this manual in a safe and convenient place.
- Do not maintain or repair SPF-9/FC-9 until you read and understand the instructions in this manual.
- Horizon International Inc. shall not be liable for incidental consequential damages resulting from : improper or inadequate maintenance by customer; unauthorized modification or misuse; operation outside of the environmental specifications for the product.
- Horizon International Inc. pursues a policy of continuing improvement in design and performance of the product. Therefore, the product design and specifications are subject to change without prior notice and without our legal obligation.
- All rights are reserved. No part of the manual may be photocopied, reproduced or translated to another language without the prior written consent of Horizon International Inc.
I
171808/SPF9FC9/01E/DV US501009-01
Safety Precautions
- The signal word WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
- The signal word CAUTION indicates a potentially hazardous situation which, if not avoided, may result in damage on machines. It may also be used to alert against unsafe practices.
- Read and understand all safety instructions with signal word such as WARNING and
CAUTION. If safety instructions are ignored, personal injury may result.
- Horizon International Inc. cannot anticipate every possible situation that might involve a potential hazard. The instructions in this manual and warning labels on the machine are therefore not all inclusive.
- Do not operate the machines when any covers are removed.
- Some of the drawings in this manual show the machine uncovered for explaining the detail or inside of machine.
II
I. Necessary Tool for Maintenance and Repair
Use the following tools for maintenance and repair.
1.
Screw Driver
2.
Screw Driver
3.
Allen Wrenches
4.
Open-ended Wrench
5.
Box Wrench
6.
Snap-ring Expander
No. 2
6 to 7 mm
1.5, 2, 2.5, 3, 4, 5, and 6 mm
5.5 x 7 mm
5.5 mm
8 x 10 13 x 17
II. Signs and Abbreviations in This Manual
1. The following signs in this manual represent wire color.
2. The following abbreviations in this manual represent electronic and electrical parts.
Sign Color
BRN
RED
ORN
YEL
GRN
BLU
VIO
GRY
Brown
Red
Orange
Yellow
Green
Blue
Violet
Gray
WHT White
BLK Black
Abbreviation Meaning
CL
BK
SW mSW
M
LED
VR
RY
Clutch
Brake
Switch
Microswitch
Motor
Light Emitted Diode
Potentiometer
Relay
III
Contents
Important Information .......................................................................................................... I
Safety Precautions .................................................................................................................. II
I. Necessary Tool for Maintenance and Repair ..................................................................... III
II. Signs and Abbreviations in This Manual ......................................................................... III
1. Specifications ................................................................................................................... 1
2. Operation Overview ........................................................................................................ 3
3. Sheet Flow ........................................................................................................................ 4
4. Drive Section .................................................................................................................... 7
5. How to Remove Covers ................................................................................................... 9
6. Knife Replacement .......................................................................................................... 11
7. Troubleshooting ............................................................................................................... 13
8. Electronic Parts Layout .................................................................................................. 21
9. Control Panel LED Descriptions ................................................................................... 23
10. Line Diagram ................................................................................................................. 25
IV
1. Specifications
1-1 SPF-9
Function
Sheet Size
Stapling and Folding, Side Stapling, Corner Stapling, Folding
Stapling and Folding : A3, A4 (11" x 17", 8.5" x 11")
Side Stapling/Corner Stapling : A4 (8.5" x 11")
64 gsm ~ 130 gsm (16# Bond to 36# Bond) Sheet Weight
Stapling and Folding Thickness up to 20 sheets of 64 gsm / up to 10 sheets of 130 gsm
(14 sheets of 20# Bond)
Side Stapling Thickness up to 20 sheets of 130 gsm (36# Bond)
Corner Stapling Thickness up to 20 sheets of 130 gsm (36# Bond)
Production Speed
Stacker Pile Height
2,000 booklets / hour
Stapling and Folding : 40 booklets (A3 - 64 gsm, 10 sheets)
Side Stapling : 100 booklets (A4 - 64 gsm, 10 sheets)
120 mm (4.7") (Fixed) Staple Distance
Staple
Sensor
Cartridge type, 5,000 staples
No Staple, Sheet Jam, Misfeed on Collator
Counter 4 digits (No memory)
Machine Size (W x D x H) 1,240 x 621 x 796 mm (48.8" x 24.4" x 31.3")
Machine Weight
Power
154 kg (339.2 lb)
220-240 V 50 Hz, 115-120 V 60 Hz, 100 V 50/60 Hz
Power Consumption
Options
60 Hz : 410 W 50 Hz : 375 W
Fore-edge Trimmer FC-9, Delivery Conveyor ED-9
1
1. Specifications
1-2 FC-9
Sheet Size
Trimmed Size trimming Thickness
Trimming Width
Production Speed
Detector
A3, A5, 11" x 17", 5.5" x 8.5"
Maximum : 323 x 225 mm (12.7" x 8.8")
Minimum : 180 x 105 mm (7" x 4.2")
64 gsm 40 sheets (16# Bond : 40 sheets)
Maximum : 13 mm (0.5")
2,000 books/hour
Sheet Jam, Knife Lock, full Trimming
Counter Total Counter
Machine Size (W x D x H) 445 x 621 x 796 mm (17.6" x 24.5" x 31.4")
Machine Weight 101 kg (221 lb)
Power
Power Consumption
220-240 V 50 Hz, 115-120 V 60 Hz, 100 V 50/60 Hz
150 W
The machine design and specifications are subject to change without any notice.
2
2. Operation Overview
2-1 SPF-9
Connecting cable on SPF-9 is connected to collator.
1. Turn on power switch on SPF-9.
On operation panel,
- automatic mode lamp will illuminate.
- stapling & folding lamp will illuminate.
2. Turn on power switch on collator.
3. Pile sheets into collator and set required set up on SPF-9 following "2-1 Operation Procedure" procedure 5 to 20 (page15 to 18) in SPF-9 Operation Manual.
4. Select automatic mode with function mode select button.
5. Press start button on collator.
- Sheets delivered from collator will be stapled automatically.
6. Press stop button on collator to stop SPF-9.
SPF-9 will stop without pressing stop button in the following cases.
- Sheet jam, misfeed, and double feed occur in collator. Collator lamp on SPF-9 illuminates.
- Sheets are jammed in SPF-9. Sheet jam lamp on SPF-9 illuminates.
2-2 FC-9
Cable on FC-9 is connected to SPF-9.
1. Turn on power switch on SPF-9.
2. Turn on power switch on collator.
3. Pile sheets into collator and set required set up on SPF-9 and FC-9 following "2-1 Operation
Procedure" 5 to 20 (page 15 to 18) in SPF-9/FC-9 Operation Manual.
4. Select automatic mode with function mode select button.
5. Press start button on collator.
- Sheet delivered from collator will be stapled and folded in SPF-9 and be cut in FC-9 automatically.
6. Press stop button on collator to stop SPF-9.
SPF-9 will stop without pressing stop button in the following cases.
- Collator lamp in SPF-9 will illuminate.
- Sheet jam, misfeed and double feed occur in collator.
- Sheets are jammed in SPF-9.
- Sheets are jammed in FC-9.
- Upper knife stops at the middle of cutting process.
- Sheet jam lamp on SPF-9 will illuminate.
- Jam lamp will illuminate.
- Knife lock lamp will illuminate.
3
3. Sheet Flow
3-1 SPF-9
There are 2 ways in sheet flow.
I. When "stapling & folding" or "folding" mode is selected with operation mode select button
1. Sheets enter and hit staple and fold stopper.
2. Sheets are jogged by jog plate and jog guide (F).
3. Sheets are stapled in staple & fold mode.
4. Transport roller (F) unit and transport roller (R) unit lower at the same time staple and fold stopper rises, and transport belt transports sheets.
5. Sheets pass under gate and stop by hitting stopper in fold section.
6. Fold knife pushes fold part of sheets and fold roller nips sheets and then press rollers press sheets and sheets are ejected.
II. When "side stapling" or "corner stapling" mode is selected with operation mode select button
1. Sheets enter and hit side staple stopper.
2. Sheets are jogged by jog plate and jog guide (F).
3. Sheets are stapled.
4. Transport roller (F) unit and transport roller (R) unit lower at the same time staple and fold stopper lowers, and transport belt transports sheets.
5. Sheets pass above gate and are ejected.
4
3. Sheet Flow
Staple & Fold Stopper Unit
Gate
Transport Roller (R) Unit
Staple Unit
Transport Roller (F) Unit
Jog Roller
Jog Plate
Sheet Entrance
Side Staple Stopper
Side Staple Stopper Unit
Sheet Feed Guide A
Sheet Hold Roller
Sheet Exit
Press Roller
Fold Roller
Fold Knife
Stopper
Staple & Fold Stopper
Transport Belt
Operation Side View
Jog Guide (R)
Transport Roller (F) Unit
Staple Unit
Jog Roller
Jog Plate
Jog Unit
Jog Guide (F)
Top View from Operation Side
5
3. Sheet Flow
3-2 FC-9
There are two ways in sheet flow.
I. When "stapling & folding" mode is selected with operation mode select button
1. Sheets from sheet entrance hit stopper.
2. Belt stops and sheets are trimmed.
3. Stopper lowers, belt rotates, and then sheets are ejected.
II. When "side stapling" or "corner stapling" mode is selected with operation mode select button
1. Sheets from sheet entrance pass through FC-9.
Hold Roller
Upper Knife
Upper Transport Belt
Delivery Belt
Exit Side
Stopper
Entrance Side
Stopper Unit
Lower Transport Belt
Lower Knife
6
4. Drive Section
4-1 SPF-9
1. Electricity is charged by turning on power switch. Motor will rotate with hand feed mode.
(In automatic mode, motor will rotate as soon as collator starts.)
2. Motor drives reduction belt and reduction pulley. At this point, speed of reduction pulley will be 1/3 of motor speed.
3. Reduction pulley drives fold rollers and press rollers. When clutch is on, transport belt will be rotated by clutch pulley.
4. When clutch is turned off, transport belt will stop.
Transport Roller (9 pcs)
Press Roller
Transport Belt
Fold Roller
Timing Belt
Clutch Pulley
Reduction Belt
Motor
Reduction Pulley
Operation Side View
7
4. Drive Section
4-2 FC-9
1. Electricity is charged by turning on power switch. Motor will rotate with hand feed mode. (In automatic mode, motor will rotate as soon as collator starts.)
2. Motor drives reduction belt and reduction pulley. At this point, speed of reduction pulley will be 40 percent of motor speed.
3. Reduction pulley drives upper transport belt and lower transport belt with drive belt. And also reduction pulley drives delivery belt.
Upper Transport Belt
Drive Belt
Reduction Pulley
Hold Roller
Delivery Belt
Reduction Belt Lower
Transport Belt
Motor
8
5. How to Remove Covers
5-1 SPF-9
WARNING
- Turn power off before removing any covers.
Bind Screw
(M4 x 6) (5 pcs)
Lower part of side cover is placed on two hook plates .
Bind Screw
(M4 x 6) (4 pcs)
Bind Screw
(M4 x 6) (4 pcs)
Lower part of side cover is placed on two hook plates .
9
5. How to Remove Cover
5-2 FC-9
WARNING
- Turn power off before removing any covers.
Remove five covers as follows.
(1) Bind Screw M4 x 6 (2 pcs)
The lower part of rear cover is placed on two hook plates.
(2) Bind Screw M4 x 6 (2 pcs)
(3) Bind Screw M4 x 6 (2 pcs)
The lower part of front cover (L) is placed on two hook plates.
(4) Bind Screw M4 x 6 (2 pcs)
The lower part of cover (FL) is placed on two hook plates.
(5) Bind Screw M4 x 6 (2 pcs)
(1)
(2)
(3)
(5)
10
(4)
6. Knife Replacement
6-1 Upper Knife
WARNING
- Take care when replacing knife.
Sharp knife can cause severe personal injury.
1. Remove two cables and slide FC-9 left to access upper knife.
Cables
2. Turn air nozzle up. (2 fix screws)
3. Remove 3 fix screws and take out upper knife from upper side.
Air Nozzle
Fix Screw
4. Attach new/resharpened knife in the reverse order of removal.
NOTE
- Apply a small amount of grease on mark part of knife when upper knife is installed.
11
Fix Screw
6. Knife Replacement
6-2 Lower Knife
1. Remove upper knife referring to page 6.
2. Remove entrance guide. (2 fix screws)
3. Re move 2 entrance lower belts.
Remove sensor connector and entrance table (4 screws).
Entrance
Lower Belts
Entrance Guide
Entrance Table
4. Remove 4 fix screws and take out lower knife from lower side.
Sensor Connector
Fix Screws
5. Install new/resharpened knife with reverse order of removal.
NOTE
- Flash top surface of lower knife with trim table with knife height adjust screws.
Knife Height Adjust Screw
Align
12
7. Troubleshooting
7-1 Finishing quality is not good.
7-1-1 Sheets are not jogged neatly.
(Cause)
Jog guide (F), jog guide (R), jog plate or staple & fold stopper is (are) skewed.
(Remedy)
Adjust jog guide (F), jog guide (R), jog plate or staple & fold stopper so that they are parallel with sheets.
1. Adjust jog guide (F) and jog guide (R) so that they are parallel with front frame and rear frame respectively with adjust bolts A and B.
2. Adjust staple & fold stopper so that it is parallel with sheets with adjust bolt Cs.
3. Adjust jog plate so that it is parallel with sheets with adjust bolt D.
- In case that sheets are still not jogged neatly, refer to the next troubleshooting. (6-1-2 to 6-1-5)
Stopper must be parallel with sheets.
Adjust Bolt B
Rear Frame
Adjust Bolt C
Adjust Bolt A
Jog Guide (R)
Adjust Bolt D
Adjust Bolt D
Jog Plate
Adjust Bolt C
Staple & Fold Stopper
Font Frame Jog Guide (F)
Jog plate must be parallell with sheets.
Top View from Operation Side
13
7. Troubleshooting
7-1-2 Sheets are not folded correctly.
(Cause 1)
Sheets are not cut exactly square.
(Cause 2)
Stopper in fold section is skewed.
Measure the length of L1 and L2 of ejected sheets as shown in the drawing below.
L 1
L 2
(Remedy 1)
Fold sheet by hand and check that sheets are cut exactly square.
(Remedy 2)
Loosen nut which fixes stopper and adjust stopper with bolt so that L1 is equal with L2.
1. Remove lower side cover at delivery side.
2. Loosen bind screws on stopper. (2 pcs)
3. Loosen nuts. (2 pcs)
4. Raise/lower stopper with bolt.
5. Install side cover with the reverse procedure of removing.
Transporting Direction of Sheets
NOTE
- Determine whether stopper is raised or lowered according to length of L1 and L2.
- When L1 is longer than L2, raise left bolt or lower right bolt.
- When L1 is shorter than L2, lower left bolt or raise right bolt.
Stopper
Bind Screw
Nut
Bolt
Delivery Side of SPF-9
14
7. Troubleshooting
7-1-3 Sheets are folded correctly, but staples are not on folding line.
(Cause)
Either staple & fold stopper or stopper in fold section is not positioned correctly.
Folding Line
Staple
Transporting Direction of Sheets
(Remedy)
Adjust either staple & fold stopper or stopper in fold section position with staple & fold position adjust pulley.
1. Measure the distance between staple and folding line.
2. Loosen two fix screws on staple & fold position adjust pulley.
3. Move staple & fold stopper either delivery side or entrance side by measured length, holding staple & fold stopper shaft with your right hand.
- To delivery side, when staple and folding line are as shown in the left drawing.
- To entrance side, when staple and folding line are opposite from the position shown in the left drawing.
NOTE
Staple & fold stopper and stopper in fold section are activated together through joint belt.
Timing Belt
Joint Belt
Staple & Fold Stopper
Staple & Fold Stopper
Joint Belt
Timing Belt
Staple & Fold Position
Adjust Pulley
Staple & Fold Stopper Handle Shaft
Stopper in Fold Section
Timing Belt
Top View from Operation Side Operation Side View
15
7. Troubleshooting
7-1-4 Sheets are folded correctly, but staples are skewed.
(Cause)
Staple unit is skewed against sheets.
Folding Line
Staples
Transporting Direction of Sheets
(Remedy)
Adjust staple positions by moving staple unit base.
NOTE
- When the positions of staples and folding line is as shown in the above drawing, move the rear side of the staple base to the right or move the front side of the staple base to the left.
- When the positions of staples and folding line is opposite from the positions as shown in the above drawing, move the rear side of the staple base to the right or move the front side of the staple base to the left.
1. Insert pin into pin hole (F) at the front side.
Shaft (No.5) can be used instead of pin.
2. Loosen four M5-15 bolts.
3. Adjust staple base referring to NOTE above.
4. Fasten hour bolts.
5. Pull out pins.
Pin Hole (R)
Rear Side
Joint Plate R
Bolts M5-15
Staple Unit
Staple Base
Bolts M5-15
Joint Plate F Front Side Pin Hole (F)
Top View from Operation Panel
16
7. Troubleshooting
7-1-5 SPF-9 is set up correctly and folding is not skewed. But the result of folding is as shown below.
Folding line and staples are aligned.
Transporting Direction of Sheets
Aligned
Not Aligned
Folding Line Aligned
(Cause)
Position of staple & fold stopper indicator, jog indicator, staple & fold stopper unit, and jog unit is not correct.
(Remedy)
Move staple & fold stopper indicator or replace scale, or move jog indicator or replace scale.
7-2 Ejected booklet is smeared.
(Cause)
Press rollers are dirty.
(Remedy)
Clean press rollers with alcohol-soaked cloth.
17
7. Troubleshooting
7-3 Sheet jam causes a stop of press rollers during folding operation, or booklet is not ejected by pressing eject button even though press rollers are rotating.
CAUTION
- When press rollers stop, turn power off immediately.
(Cause)
Pressure between press rollers A and B is not proper.
(Remedy)
1. Remove cover.
2. Remove two spring 1 and two spring 2 on both front and rear frame.
3. Loosen nut.
4. Adjust pressure of press roller by turning adjust bolt.
5. Fasten nut and install springs 1 and 2.
Spring 1
NOTE
- Excessive pressure between press rollers A and B causes sheet jam without sheets' passing through press rollers.
- Weak pressure (much clearance) between pressure rollers A and B causes slip and sheets are not ejected.
Spring 2
Press Roller B
Timing Belt
Nut
Bolt
Fold Roller
Press Roller A
Front Frame from Operation Side View
18
7. Troubleshooting
7-4 Slow movement of side staple stopper causes sheet jam when side stapling or corner stapling is performed.
(Cause)
The position of solenoid in side staple stopper unit is too high, solenoid cannot pull up stopper.
(Remedy)
Lower the position of solenoid.
Side Staple Stopper
Solenoid
Stopper Guides
(4 pcs)
(Cause)
Clearance between stopper guides and side staple stopper unit is too narrow.
Side Staple Stopper Unit
(Remedy)
Widen two lower guides of four guides. Adjust position of two lower guides for smooth up/down movemnt of side staple stopper.
7-5 Finished booklets have scratches when side stapling or corner stapling is performed.
(Cause)
The position of solenoid in staple & fold stopper unit is too low, booklet hits staple & fold stopper when ejected.
(Remedy)
Raise the position of solenoid.
Scratch
Solenoids
Transporting Direction of Sheets
Staple & Fold Stopper Unit
19
7. Troubleshooting
7-8 FC-9 Stopper does not work smoothly.
(Cause)
Stopper shafts are twisted at the position of end shaft.
(Remedy)
Loosen fix screws at the top of stopper shafts screws and adjust stopper shafts so that they are not twisted. Stopper shafts twist can be checked by use of two holes
(No.3). Check that stopper is parallel to lower knife when fix screws are fastened.
Sheet Forwarding Direction
Stopper
Holes (No.3)
Stopper Shaft
End Shaft
Stopper Unit
7-9 Sheets are trimmed askew.
(Cause 1)
Sheets do not hit stopper properly because sheets slip on belt or curling sheets are caught at transport section.
(Remedy 1)
Clean belt so that sheets are transported smoothly.
(Cause 2)
Stopper is not parallel to lower knife if sheets hit stopper properly.
(Remedy 2)
Adjust stopper so that it will be parallel to lower knife.
- Loosen fix screw on stopper at adjusting side. (Hole at adjusting side is larger than that at fixed side.)
- Place a exact-square sheet as shown in the drawing.
- Fasten fix screw. Check that stopper shafts can be moved when screw is fastened.
Stopper
Fix Screw (Fixed Side)
Fix Screw (Adjustable Side)
20
8. Electronic Parts Layout
8-1 SPF-9
Sheet Presence Sensor
Receptacle
Terminal Block (Drive Motor)
Transport Belt Drive Motor
Drive Relay
Top Cover Microswitch
Sheet Pass Sensor
Panel P.C.B. QPW-461
Power Switch
Booklet Presence in Folding Section
Eject Guide Open Microswitch
Knife Home Position Sensor
Breaker
Upper : 2A 24 V
Middle : 2A Knife Motor
Lower : 5A Power
Power Supply 24V
Power Supply 5V
Brake P.C.B. QPW-465
Control P.C.B. QPW-460
21
8. Electrical Parts Layout
8-2 FC-9
Receptacle
Stopper Section Sensor
Transport Section Sensor
Panel P.C.B. QPW-477
Motor Relay
SSR
Power Supply 24 V
Stopper Solenoid
Breaker 3A
Knife Motor Driver
Power Supply 5 V
22
9. Control Panel LED Descriptions
9-1 SPF-9
CON4 CON5 CON10 CON11
L3 L4 L5 L6
Control P.C.B. QPW460
L3 Collating
L4 Collator's Feed Error
L5 Transport Belt Drive Motor
L6 Knife Motor
L7 Jog Button
L8 Eject Button
L9 Operation Mode Select Button
L10 Function Moder Select Button
L11 Sheet Pass Sensor
L15 L16 L17 L18
L7 L8 L9 L10 L11 L12 L13 L14
CON1 CON13 CON3
Not illuminate during collating.
Not illuminate when collator feed error occurs.
Illuminates during rotating.
Illuminates during rotating.
Illuminates when pressed.
Illuminates when pressed.
Illuminates when pressed.
Illuminates when pressed.
Illuminates when sheet exists on sensor.
L12 Sheet Presence Sensor
L13 Knife Home Position Sensor
L14 Booklet Presence in Fold Section
L15 Upper Cover Sensor
L16
L15 Not Used
L18
Illuminates when sheet exists on sensor.
Illuminates when knife is at home position.
Illuminates when sheet exists on sensor.
Illuminates when cover is open.
23
9. Control Panel LED Descriptions
9-2 FC-9
L13
L12
L11
L10
L9
L8
L7
L6
QPW-467
L1 L2 L3 L4
L5
L1 Stapling & Folding Mode (SPF-9) Illuminates when "stapling & folding" mode is selected.
L2 Collating Not illuminate in collating.
L3 Hand Feed Mode (SPF-9)
L4 Transport Motor
L5 Not used
L6 Knife Inching Button
Not illuminate when sheets are fed manually.
Illuminates while transport motor is activated.
Illuminates when knife inching button is pressed.
L7 Sheet Presence in Transport Section Illuminates when sheets exist in transport section.
L8 Sheet Presence in Stopper Section Illuminates when sheets exist in stopper section.
L9 Trimmings Box
L10 Knife Sensor
Illuminates when trimmings box is open.
Illuminates when knife reaches the upper limit position.
Illuminates when door is open.
L11 Door
L12 Not used
L13 Not used
24
10. Line Diagram
10-1 SPF-9
CON9 CON6 CON7 CON8 CON2
CON9 CON12
25
10. Line Diagram
10-2 FC-9
Door Microswitch
Door Relay
Connecting Cable
Counter
Transport Motor Relay
SSR for Power Switch
CON8 CON1 CON5 CON6 CON4 CON7
Control P.C.B.
QPW-476
Stopper Solenoid
Stopper Section Sensor
Knife Upper Limit Sensor Entrance Section Sensor
Power Supply 24 V
Power Supply 5 V
Trimmings Box Open Microswitch
Knife Motor Driver
Receptacle with Noise Filter
Door Relay
Breaker 3 A
Transport Motor
Power Supply 24 V
Power Supply
5 V
SSR
Transport Motor Relay
Terminal Board
Knife Motor Driver
26
SM_SPF9/FC9
Revision 1
Standard Business Systems
10 Connector Road, Andover, MA 01810
(978) 470-1920 (978) 470-2771
