AG - 10

Parts & Service

AG – 10 Specifications

Capacity (struck)…………………………………..8.4 yd

(heaped)………………………………….10 yd

Weight (empty)…………………………………...17,512

Tongue Weight (empty)…………………………..1,500

Width of Cut………………………………………..8 ft

Overall Width………………………………………9 ft. 1 in.

Ground Clearance At Bit……………………………18 in.

Negative Cut…………………………………………12 in.

Overall Length……………………………………...348 in.

Gate Opening……………………………………….46 in.

Cylinders (lift)……………………………………..6 x 22

(gate)……………………………………3.5 x 20

(push off)……………………………….4.5 x 32

Tires (front)…………………………………..15 x 19.5

(rear)…………………………………..20.5 x 25

Inflation 15 x 19.5 ……………………………... 60 psi

20.5 x 25………………………………. 58 psi

Rims (front)………………………………….19.5 x 12.25

(rear)……………………………………17 x 25 3 pc

Cutting Edges

(center)………………………………..7/8 x 16 x 48”

(outside)………………………………7/8 x 13 x 23.75”

Spindle Rating

(front)…………………………………12,000 lb

(rear)………………………………….20,000 lb

Hydraulic Hoses…………………………………….3000 psi

Hydraulics are controlled by a 2 valve system, using a steel sequencing block and requiring

2 tractor remotes.

Scheduled Maintenance

A quality, high temperature grease should be used when lubricating the machine. Most areas of lube are scheduled daily, ( 8 to 10 hrs. of running). There are 24 grease zerks on the Ag 10 that should be greased daily. There are also 1 zerk per axle that are greased weekly with 3 pumps of grease.

All bolts are torqued at the factory during assembly. After 24 to 36 hours of running, the Dealer service should recheck the torque on bolts, wheel, axle, and pin retainers. Each time the machine is greased, the operator or maintenance should look at these areas and the bolts involved, to be sure none are working loose.

After each 1000 hours of operation with the machine, the hitch, wheel, axle and pin retainers should be retorqued, per the torque value chart in this manual.

For safety, identification, and general information, all missing or damaged decals on the machine should be replaced.

The ICON AG 10 has the interior of the bowl painted with a carbon base graphite paint, which rejects dirt.

Should that paint wear off over a period of time, replacement paint may be ordered by the gallon through the original dealer.

The cutting bits for the earthmover are available through ICON, or local CAT Dealers. Refer to the cutting edge section of this manual for size and part numbers.

All retaining pins have replaceable bushings. Watch the pin locations in action to review for loose and worn operation.

The timing of the loaded machine is critical to it’s performance. On the 2 valve setup, it is important that the gate and push off wall work as they should. Adjustments to the timing can be made at the sequence block on the tongue of the machine. (refer to the timing chart in the manual for instructions).

Remember, the longevity of your machine will depend on proper operation and maintenance.

Warning!

To prevent a hazardous situation, which if not avoided can result in injury or death.

Read and follow these instructions!



Read and understand the operator’s manual before operating the machine. Allow no one to operate

the machine before reading the manual and being instructed on the proper operation.



Before servicing the machine, block the wheels, shut the tractor off, set the brakes, and remove the

key. If working under the machine, block the machine up for a safe and secure working area. Apply any

and all safety stops provided.



When working with hydraulic lines, cylinders, or fittings, wear protective clothing and safety glasses

to guard against high pressure oil leaks.





Do not allow anyone on, or near the machine while it is running or in motion.

Do not operate the machine on a steep incline or slope that could create an imbalance or rollover.

Safety Section 3a

Foreword

Literature Information

This information should be stored in the literature holder located on the machine.

This manual contains safety information, operating instructions, lubrication and maintenance information.

Maintenance

The maintenance section is a guide to machine care. The illustrated step by step procedures covers the most important of the maintenance schedule. Regular routine publication show details that can differ slightly from your personal machine. Shields and covers may have been removed to allow for illustrations.

Constant improvement and knowledge of product design may cause changes to your personal machine that is not listed in this manual.

Read, understand, and keep this manual with the machine to aid in repairs, adjustment, service and parts identification.

Whenever a question arises regarding your machine, or this manual, please contact Product

Support for assistance.

Safety

The safety section of this manual lists basic safety precautions. In addition, this section shows the location of safety signs and decals used on this machine.

Read and understand the basic precautions listed in the safety section before operating or performing lubrication, maintenance or repair work on this machine.

NOTE: Before any service or repair work is performed, make certain that all safety stops are in place.

Be certain to remove all safety stops when repairs are complete.

Operation

This operation section is a reference guide for the new operator and a refresher for the experienced operator. Operating techniques shown are basic, skill and technique will increase with knowledge and usage of the machine.

Maintenance Intervals

Normally, all lubrication should be on a daily basis. However, certain locations only require lubrication on a weekly basis or require a specific quantity. These locations will be marked clearly, showing and describing requirements.

Under extremely severe, dusty/wet/sandy conditions, or if the haul is long and rough, more frequent lubrication and inspection of highly stressed areas is recommended.

Safety Section

General Hazard Information

Safety Section

General Hazard Information

A “Do Not Operate” warning tag or similar warning tag should be attached to the start switch or controls before servicing or repairing the machine.

Know the width of your equipment in order to maintain proper clearance when you operate the machine(s) near fences or boundary obstacles.

Be aware of high voltage power lines or buried power cables. If the machine comes in contact with these hazards, serious injury or death may occur, from electrocution.

Fluid Penetration

Pressure can be trapped in a hydraulic system, long after the engine has been stopped. The pressure can cause fluid or fittings/ends to detach rapidly, if the pressure is not released properly.

Do not remove any hydraulic components until pressure has been relieve, or personal injury may result. Do not disassemble any hydraulic components or parts until the pressure has been relieved, or personal injury may occur.

Always use a board or protective shield

Wear a hard hat, protective glasses, and other protective equipment, as required.

Hydraulic fluid is under extreme pressure

Do not wear loose clothing or jewelry that can and can cause serious injury and possible snag on controls or other parts of the machine. death. A pin hole leak can cause severe

Make sure all protective shields and covers are injury. If fluid is injected into your skin, you secured in place on the machine. must seek treatment immediately. Seek

Obey all local regulations for the disposal of treatment from a doctor that is familiar with liquids. this type of injury.

Do not allow unauthorized personnel on the machine

Containing Fluid Spillage

Unless you are instructed otherwise, perform maintenance with the machines in the servicing

Care should be taken to prevent spillage of position. The operation and maintenance manual hydraulic fluids during maintenance, testing, will describe the proper position. and repair of the machine. Prepare to collect

Never put maintenance fluids (hydraulic) into any fluid with suitable containers before glass containers. Drain all liquids into suitable opening any system containing fluids. containers.

Obey all local regulations for the disposal of liquids.

Trapped Pressure

Improperly disposing of waste fluids can

Pressure can be trapped in a hydraulic system. threaten the environment. Potentially harmful fluids should be disposed of

Releasing trapped pressure can cause sudden according to local regulations. movement of the machine. Use caution if you

Always use leakproof containers when disconnect hydraulic lines or fittings. High you drain fluids. Do not pour waste onto the pressure oil that is released, can cause a hose to ground, or into any source of water. whip. High pressure oil that is released, can cause oil to spray.

Fluid penetration can cause serious injury or death.

Safety Section

Crushing/Cutting Prevention

Support the machine properly before you perform any repairs or maintenance beneath that machine.

Do not rely on the cylinders to hold the machine up.

If a control is moved or a hydraulic line breaks, the machine can fall.

Never attempt adjustments while the machine is in motion.

Stay clear of all rotating and moving parts.

If it is necessary to remove shields or panels for repairs/maintenance, be certain to replace them before using the machine.

When you strike a pin or retainer with force, chips and other debris can fly off the object.

Make sure that no one can be injured by flying debris before striking any object. To avoid injury to your eyes, wear protective glasses when striking any object.

Make certain that the cylinder stops are in place before making any adjustment/repairs under the machine.

The stop pins should be in place on the clam before working around the front of the machine.

Line, Tubes and Hoses

Inspect all lines and hoses for wear and chaffing.

The hoses must be properly routed and have adequate support and the clamps should be secure.

Tighten all connections to the recommended torque.

Do not bend high pressure lines. Do not install any lines that are bent or damaged.

Repair any lines that are loose or damaged.

Check lines, tubes and hoses carefully. Do not use your bare hands to check for leaks. Use a board or cardboard to check, as high pressure fluid can enter soft tissue.

Tighten all fittings and clamps to proper torque specs.

Replace the parts if any of the following conditions are present.



End fittings are damaged or leaking.













Outer coverings are chafed or cut.

Wires are exposed.

Outer coverings are ballooning.

Flexible part of the hoses are kinked.

Outer covers have embedded armoring.

End fittings are displaced.

Before Operation

Clear all personnel from the area.

Clear all obstacles that are in the path of the machine. Beware of hazards, such as wires, ditches, etc.

Whenever you are working around this machine, always wear the protective equipment that is required by the conditions of the job site.

Refer to the “Daily Walk around

Inspection “ for tips on what to look for, before daily use.

Be aware of the width of your machine, and be certain there is enough clearance for you to maneuver without hitting obstacles beside you.

General Operation

Each scraper operator has his/her own methods of hydraulic sequence and overall operation of the machine. The following are suggestions as to the ICON Earthmover. Personal methods and choice of tractors may alter these suggestions.

The ICON/Landoll machine is completely assembled and checked at the factory. It is requested of the

Dealer that after the first 24-36 hours of operation, the machine is then checked , and adjusted, if needed.

There are 24 zerks of the AG-10 that are marked grease daily, and 1 on each axle that are grease weekly.

Each bolt is torqued to proper specs at the factory, and after the initial 24 - 36 hours of running, should be rechecked. All retaining pins have replaceable bushings. Watch the pin locations in action to review for loose and worn operation.

Hydraulic hose configuration at the front of the machine is arranged to fit the late model remotes. Some pulling units may require the relocation of the hydraulic hose configuration. A two-valve sequencing setup is standard. This allows the raise/lower to be controlled by valve #1, and gate/push-off by valve #2.

The operation of these valves is left to operator choice, for push/pull . This is controlled by the position of the hoses at the tractor. On a two valve system, the timing of the loaded machine is critical to it’s performance. It is important that the gate and push off wall work as they should. Adjustments to the timing is made at the sequence block, located on the tongue of the machine. This setting is factory set, but in time, can need re-adjustment. (Refer to the timing chart in the manual for instructions.)

A visual depth gauge is located at the right side, front of the machine. It allows the operator to set the cutting edge to the proper depth for a smooth cut, or eject depth of the load. (It is marked in tenths of an inch)

The ICON/Landoll Earthmovers have portions of the bowl painted with a carbon based, graphite paint, which helps to reject dist. Should this paint wear off over a period of time, replacement paint may be ordered thru the dealer.

Be patient for the first few hours of learning to operate the machine. Time and experience will produce expert results. Any type of cutting edge machine will have the tendency to create a “washboard” effect, if too much speed and inconsistent depth is used. Also, if the machine is used to “back level” or drag , be certain that the gate is in the fully up position and the push off wall is completely forward. This allows the operator to carry a small amount of material to fill with (if needed).

This machine is designed to be used with a pulling unit of 400 hp. maximum. Additional horsepower will shorten the life of the unit and will alter the warranty. Responsible operation and proper maintenance will provide many hours of expert results and a durable machine.

NOTE: This machine is not intended for highway use, it should be used off road only. If public roadway travel is necessary, be certain of regulations concerning width, lighting, and safety requirements.

WARNING!



Read and understand the operator’s manual before operating the machine. Allow no one to operate







 the machine before reading the manual and being instructed on the proper operation.

Before servicing the machine, block the wheels, shut the tractor off, set the brakes, and remove the key. If working under the machine, block the machine up for a safe and secure working area. Apply any and all safety stops provided.

When working with hydraulic lines, cylinders, or fittings, wear protective clothing and safety glasses to guard against high pressure oil leaks.

Do not allow anyone on, or near the machine while it is running or in motion.

Do not operate the machine on a steep incline or slope that could create an imbalance or rollover.

Component location

ICO2019

1/4 x 1 1/4”

1/2 x 1”

ICO0525

ICO0236

Rim: 4000657

Tire: 4000636

3/4 x 1 1/2”

ICO1133

ICO2250

ICO1133

ICO2172/73

ICO1133

ICO2045 (4) places on linkage

ICO2228

4001542

ICO2259

4001544

ICO2063

ICO0239

ICO2258

ICO2233

5/8 x 7”

4001541 Spindle

ICO1066

4001452

ICO2259

ICO2063 ICO2233

ICO0239

ICO2199

ICO2258

ICO2230

ICO2262

4001252

4001544

ICO2248

ICO2250

ICO2172/73

ICO0229

ICO1066

5/8 x 7”

4001541 Spindle

4001452

ICO2261

ICO2230

ICO2259

4001236

ICO2063

3/4 x 1 1/2”

1 x 6 1/2”

ICO2199

ICO2251

Also behind shield

1/2 x 1”

Cylinder 4001543

ICO2250

1/2 x 1”

ICO1133

3/4 x 1 1/2”

ICO2258

5/8” Nyloc

Dolly Transport Strap ICO2263

safety bracket before us nsport e.

Tire Inflation 20.5 x 25 rear………….58 psi

15 x 19.5 front…………60 psi

AG -10 Parts Location

5

7 4

2

1

19

10/11

Ref # Part # Description

1. ICO2227 Main Frame

2. ICO2233 Gate

3. ICO2256 Dolly Hitch

4. ICO2262 Wear Strips

5. 4000657 Rim, 17.5 x 25 3 pc

6. 4001544 Rim, 19.5 x 12.25

7. 4000636 Tire, 20.5 x 25 - 16 ply

8. 4001252 Tire, 15 x 19.5 - 12 ply

9. 4001452 Hyd. Sequence Valve Block

10. ICO2172 Left Side Router Bit

11. ICO2173 Right Side Router Bit

12. ICO2265 Cylinder Safety Stop (lift)

13. 4001548 Pintel Hitch (Cat 4, 106,000)

14. ICO2231 Dolly Hitch (gooseneck)

15. ICO2256 Dolly Hitch (gooseneck forward)

16. ICO2257 Hitch Clevis

17. ICO2253 Dolly Hitch Pivot

18. ICO2252 Dolly Hitch Cross

19. ICO2248 Hyd. Shield

1

1

1

1

2

2

2

2

Qty

1

1

1

2

1

1

4

1

1

1

1

12

14

3

8

6

17

18

9

15

16

13

2

1

10

9

8

6

3

7

Ref # Part # Description

1. ICO2233 Gate

2. ICO2230 Push Off Wall

3. ICO2250 Side Shield

4. ICO2172 Left Side Router Bit

5. ICO2173 Right Side Router Bit

6. ICO2251 Tapered Gate Pin

7. ICO1133 Pin, 2.5 x 5.75

8. 4001236 Hyd. Cylinder 6 x 22 (37 1/4” )

9. ICO2265 Safety Stop (lift)

10. ICO2199 Safety Stop (gate)

11. ICO2263 Dolly Transport Strap

4/5

1

1

1

1

4

7

1

Qty

1

1

2

1

11

1

1

9

5

3

2

6

Ref # Part #

1. 4001545

2. 4000958

3. 4001539

4. 4001541

5. ICO2229

6. ICO1133

7. ICO2253

8. ICO2259

9. ICO2258

10. 4001542

Description

Cutting Edge, 7/8x13x23.75

Cutting Edge, 7/8x16x48

Spindle, 20,000#

Spindle, 12,000#

Push Off Frame

Pin, 2.5 x 5.75

Dolly Hitch Pivot

Pin, 12.75”

Pin, 13 5/8”

Hyd. Cyl. 4.5 x 32 (push off)

1

7

1

1

2

1

Qty

2

1

2

2

8

4

7

AG-10 Assembled View

Push Off Wall Assembly

1

5

4

7

3

5

7

2

5

Ref #

1.

2.

3.

4.

5.

6.

7.

Part #

ICO2230

ICO2229

ICO2228

ICO2232

ICO1133

ICO0525

ICO2045

Description

Push Off Wall

Push Off Frame

Push Off Linkage

Push Off Support

Pin, 2.5 x 5.75

Pin, 2.5 x 10.75

Pin, 1.5 x 4.25 chrome

2

1

7

2

Qty

1

1

4

6

Dolly Hitch Components

5

1

3

2

5

3

Ref #

1

2

3

4

5

Part #

ICO2252

ICO2253

ICO1066

NH 2 1/2

NH 1 1/2

4

Description

Dolly Hitch Cross

Dolly Hitch Pivot

MDU Hitch Pin 14”

Nut, Hex 2 1/2”

Nut, Hex 1 1/2”

Qty

1

1

2

1

2

4001548 Category 4

106,000 lb rating

BH 1 x 8 1/2”

1 x 8 1/2”

ICO2260 10 1/2”

1 1/2” Nut

AG - 10 Bolt Listing

Where Used Description

Frost Bit and Cutting Edges BP, Bolt, Plow 1 x 2 1/2”

WFH, Washer, Flat, Hard 1”

NJ, Nut, Jam 1”

Router Bits

Push Off Support

PO Wearstrip

BP, Bolt, Plow 3/4 x 2 1/2”

WFH, Washer, Flat, Hard 3/4”

NJ, Nut, Jam 3/4”

BH, Bolt, Hex 1 x 6 1/2”

NL, Nut, Nyloc 1”

WF, Washer, Flat 1”

WFH, Washer, Flat, Hard 1”

BC, Bolt, Carriage 1/2 x 1 1/2”

WFH, Washer, Flat, Hard 1/2”

NH, Nut, Hex 1/2”

PO Linkage Pins (1 1/2) BH, Bolt, Hex 1/2 x 3”

NL, Nut, Nyloc 1/2”

PO Frame to Main Frame WM, Washer, Machine 2.5 x 3.5OD

PO Frame to PO Wall

PO Pin Caps

Gate to MF and Cyl.

WM, Washer, Machine 2.5 x 3.5OD

BH, Bolt, Hex 5/8 x 1 1/2”

WFH, Washer, Flat, Hard 5/8”

NJ, Nut, Jam 1 1/2”

WFH, Washer, Flat, Hard 1 1/2”

(4001521) Woodruf Key 1 x 1/4”

(4001499) Washer, Lock 2.46x1.58

Side Shields

Side Shields (gate cyl)

Hyd. Block

BH, Bolt, Hex 1/2 x 1”

WFH, Washer, Flat, Hard 1/2”

BH, Bolt, Hex 1/2 x 1”

WFH, Washer, Flat, Hard 1/2”

BH, Bolt, Hex 1/2 x 6”

WF, Washer, Flat, 1/2”

NW, Nut, Whiz 1/2”

4

4

8

4

4

4

4

4

10

10

10

10

10

10

Qty

16

16

16

4

4

4

4

4

4

8

8

8

8

2

4

2

Bolt Listing (cont)

Where Used

Light Brackets

Lights to Bracket

Description

BH, Bolt, Hex 1/2 x 1”

WFH, Washer, Flat, Hard 1/2”

BH, Bolt, Hex 1/4 x 1 1/4”

NW, Nut, Whiz 1/4”

Hose Clamps

Gate Safety Stop

NL, Nut, Nyloc 1/2”

WFH, Washer, Flat, Hard 1/2”

Hitch Cross to Gooseneck NC, Nut, Castle 1 1/2”

WFH, Washer, Flat, Hard 1 1/2”

Pin Keepers

BH, Bolt, Hex 1 x 6 1/2”

WFH, Washer, Flat, Hard 1”

NL, Nut, Nyloc 1”

PC, Pin, Cotter 5/16 x 2 1/2”

BH, Bolt, Hex 3/4 x 1 1/2”

BH, Bolt, Hex 3/4 x 1 3/4”

WFH, Washer, Flat, Hard 3/4”

Spindle Keepers

Depth Gauge

BH, Bolt, Hex 5/8 x 7”

BH, Bolt, Hex 5/8 x 9”

NL, Nut, Nyloc 5/8”

NL, Nut, Nyloc 5/8”

WF, Washer, Flat 5/8”

Dolly Transport Strap

Clevis To Dolly

Pintle To Clevis

Safety Stop (lidt)

Dolly Pivot to Dolly

Clevis Safety

NL, Nut, Nyloc 3/4”

WF, Washer, Flat 3/4”

NJL, Nut, Jam Nyloc 1 1/2”

WF, Washer, Flat 1 1/2”

BH, Bolt, Hex 1 x8 1/2”

WFH, Washer, Flat, Hard 1”

NL, Nut, Nyloc 1”

PCL, Pin, Wire Lock 1/4 x 3”

WFH, Washer, Flat, Hard 1 1/2”

(4000923) Pin, Clevis 1/2 x 4 1/2”

(4001443) Bridge Pin 3 x 5/32”

NS, Nut, Slotted 2 1/2” Course

2

2

2

1

1

1

1

1

1

1

1

1

2

2

2

2

4

8

8

11

11

Qty

4

4

2

6

2

1

1

1

11

2

13

Gate

Ex ten d 5

001

204

Gate Retract

5001204

4001452

4001451

4001449

4001450

PO Extend

5001201

PO Retract

5001202

50

012

03

To

Tr acto r

500

120

3

To

Trac tor

Raise/

Lo wer

50

01

Raise/

20

0

Lo wer

50

01

20

0

1/2 x 6”

AG - 10 Hydraulics

Hydraulic Hose 5001205 and 5001206 (2 ea) are ran through the tube and covered by the side shields. They run to the gate cylinders.

Hydraulic Hose Listing (5001199)

Part #

5001200

5001201

5001202

Description

Hose, 12FFORX -12M3K x 540” - 12FFOR

Hose, 12FFORX-12M3K x 328” - 12MB

Hose, 12FFORX-12M3K x 522” - 12FFOR

5001203

5001204

5001205

5001206

Hose, 12FFORX - 12M3K x 132” - 12MB

Hose, 12FFORX - 12M3K x 225” - 12FFOR

Hose, 8FFORX - 8M3K x 72” - 8FFORX

Hose, 8FFORX - 8M3K x 92” - 8FFORX

Fittings (5001198)

5000793 Hyf-EL. FF 12MFFOR-12MB90

5000796

5001207

5001208

5000983

Hyf-45, FF 12NFFIR-12MB45

Hyf-45. FF 8MFFOR-8MB45

Hyf-Adap 8MFFOR-12FFOR

Hyf-TEE 12MFFORT

5000833

5000424

5000836

5000835

5001152

5000478

Hyf-Adap 12MB-12MFFOR

Hyf-Plug 12MB-HH Plug

Hyf-Adap 10MB-12FB

Hyf-Pioneer Male 8010-16P 10FB

Hyf-El 4MJ-4FJX90

Hyf-Adap JIC 4MJBH-2FP

4

1

4

4

2

5

1

4

4

2

2

2

2

2

2

Qty

2

1

1

AG - 10 Cutting Edges

Part #

4000958

4001545

ICO2172

ICO2173

Description

Cutting Edge - 7/8 x 13 x 23.75

Left Side Router Bit

Right Side Router Bit

ICO2262 Push Off Wear Strip (4’)

Hardware Required

Cutting Edges use 1” x 2 1/2” Grade 8 Plow Bolts

Wear Strips use 1/2” x 1 1/2” Carriage Bolts

Side Router Bits use 3/4” x 2 1/2” Plow Bolts

Cutting Edge - 7/8 x 16 x 48 (center bit)

Qty

1

2

1

1

2

16 total

10 total

5 ea.

Decal Listing For AG - 10

Part #

4000931

4000935

4000937

4000938

4000940

4001418

4000396

4000949

4001564

4001560

4001445

Description

Warning, High Pressure

Parts Manual

3 Pumps of grease weekly

Grease Daily

Danger Pinch

Depth Gauge

Gate Gauge

Hyd. Color Codes

Tire Pressure 20.5

Tire Pressure 15x19.5

Safety Stops

4001446

4000372

Remove Safety Stops

Warning, Moving Parts

4001546L Hitch Decal (left side)

Location

Cyls, & Pressure Lines

Manual Tube

Hubs

All zerk locations

All Pivot Points

Gauge Rod

Right Side of Gate

Front of Tongue

Rear Frame/near tires

Front Dolly near tires

Near Safety Stops

Front, Near Stops

Near Moving Components

Top of Dolly Frame

4001546R Hitch Decal (right side)

4001547L Side Decal (left side)

4001547R Side Decal (right side)

4000335 Slow Moving Vehicle

4001535

4001534

4001533

Ref Tape (yellow)

Ref Tape (red)

4001285

4001516

4000941

Top of Dolly Frame

Side of Machine

Side of Machine

Rear Center of Frame

Front and Side of Machine

Back of Machine

Ref Tape (orange)

Horsepower Rating (400)

Off Road Use Only

Back of Machine

Front of Tongue

Front of Tongue

To Prevent A Hazardous Situation Side of Dolly Frame

4000702

4001522

4001551

4001248

4001484

4001550

Ref Tape (red/silver) 18”

Landoll/ICON (black)

Warning: remove transport bracket Rear of dolly, near bracket

Machine to be pulled with

Contact utilities before digging

Allow no riders

Vertical on Rear Frame

Upper Side of Machine

Front of Tongue

Front of Tongue

Front of Tongue

Qty

1

2

2

2

3

6

1

4

1

1

4

1

4

24

1

1

2

4

2

2

1

1

1

1

2

2

2

1

1

1

Decal Location AG 10

Decal Kit—#2000638

4001546R

4001522

4001547R

4001535

4000396

4001418

4000931

4001285

4000949

4000702

4000936

4001534

4001533

4001516

4000335

4000938

4000937

4001546L

400941

4000372

4000931

4000931

4001446

4001445

4001535

4001446

4001516

4001484

4001550

4000949

4001248

4001285

4000372 both sides

4000941 both sides

4000372 both sides

4000931

4000940 both sides

4001551 both sides

4000931

4000940 both sides

4001446

4001445

4001535

Yellow

ICON/Landoll

4000702

4001534

4000335

4001435

4000937

4001533

AG - 10 Earthmover

Assembly, Lube and Check List

________1. Install Cutting Bits, and Side Router Bits. Torque all mounting bolts.

________2. Install Lift Cylinder. Torque all pin retaining bolts.

________3. Position and pin Eject Wall. Install Eject Cylinder and Linkage. Torque all retaining bolts.

Install the depth gauge components.

________4. Locate and pin front gate and gate lift assembly. Install gate cylinders. Torque all retaining

bolts.

________5. Install front Dolly Hitch Assembly. Torque all pin retaining bolts.

________6. Install axle and wheel components. Torque all retaining bolts.

Inflate tires to required PSI.

________7. Locate and assemble all hydraulic fittings, hoses and blocks. Properly tighten fittings,

taking care not to overtighten. Install the proper markings to each hose and apply color

coded hose wrap.

________8. Install safety lighting components, route wiring and install plug retainer. Cycle and check

lighting system with 12 volt system tester.

________9. Lubricate all moving components with high temperature grease.

________10. Fill hydraulic system with Mobil 424 hydraulic oil. Using hydraulic pump, activate all

moving parts and bleed air from the system (if necessary). Hold 3000 PSI hydraulic

pressure against all cylinders, fittings, and hoses for a minimum of 4 minutes. Check all

components for leaks.

________11. Install all side covers and shields. Torque all retaining bolts.

________12. Clean and touch up paint the machine. Attach the manual container.

________13. Apply the serial tag, operations, lube and identification decals.

________14. Check function and proper engagement of all safety stops.

ICON Supervisor Signature: All of the above listed assembly and check functions have been completed per my rigid standards.

Serial #______________________________ _________________________________________

checked by

Date:________________________________ _________________________________________

Supervisor

Customer Copy

AG - 10 Earthmover

Assembly, Lube and Check List

________1. Install Cutting Bits, and Side Router Bits. Torque all mounting bolts.

________2. Install Lift Cylinder. Torque all pin retaining bolts.

________3. Position and pin Eject Wall. Install Eject Cylinder and Linkage. Torque all retaining bolts.

Install the depth gauge components.

________4. Locate and pin front gate and gate lift assembly. Install gate cylinders. Torque all retaining

bolts.

________5. Install front Dolly Hitch Assembly. Torque all pin retaining bolts.

________6. Install axle and wheel components. Torque all retaining bolts.

Inflate tires to required PSI.

________7. Locate and assemble all hydraulic fittings, hoses and blocks. Properly tighten fittings,

taking care not to overtighten. Install the proper markings to each hose and apply color

coded hose wrap.

________8. Install safety lighting components, route wiring and install plug retainer. Cycle and check

lighting system with 12 volt system tester.

________9. Lubricate all moving components with high temperature grease.

________10. Fill hydraulic system with Mobil 424 hydraulic oil. Using hydraulic pump, activate all

moving parts and bleed air from the system (if necessary). Hold 3000 PSI hydraulic

pressure against all cylinders, fittings, and hoses for a minimum of 4 minutes. Check all

components for leaks.

________11. Install all side covers and shields. Torque all retaining bolts.

________12. Clean and touch up paint the machine. Attach the manual container.

________13. Apply the serial tag, operations, lube and identification decals.

________14. Check function and proper engagement of all safety stops.

Comments:_________________________________________________________________________

__________________________________________________________________________________

__________________________________________________________________________________

__________________________________________________________________________________

__________________________________________________________________________________

__________________________________________________________________________________

Serial #_________________Date_____________ _________________________________________

Supervisor

Product Support Copy

Please take the time to register your machine online to be eligible for warranty, if needed.

1. Go to WWW.Landoll.com

2. Click on support services

3. On left hand side, click on warranty processing

4. Pop up box will ask for user name and password

5. Enter word dealer in user name and landoll in password

6. Click on ag registration, and enter info. Your machine will be registered.

LANDOLL CORPORATION

Product Warranty

LANDOLL CORPORATION 1600 W. 8 th

St. Beloit KS 67420

(referred to as LANDOLL in this document)

LANDOLL shall Warrant workmanship and materials on the

ICON Farm Products for a period of 270 calendar days from the date of

original purchase, lease, or rental, from the original Dealer, and in accordance with the following terms and conditions.

Should any part or component fail within the Warranty period, and

under normal use conditions, LANDOLL shall supply a new part or

component for replacement through the original Dealer. Cost of normal ground freight, for that part or component to the Dealer, shall be paid by

LANDOLL. Repair and replacement labor cost, from the original Dealer, shall be paid by LANDOLL at a rate negotiated by LANDOLL.

No further expense shall be paid by LANDOLL, including but not

limited to, loss of time or income.

LANDOLL shall not provide Warranty on any part or component that

has failed due to abuse, misuse, alteration, improper maintenance, or normal wear. Failure occurring while being pulled by a tractor in excess of engine horsepower, as described in the owners manual and/or posted on the machine, is considered abuse and misuse and shall not receive Warranty.

Warranty applies only to normal. intermittent agricultural use, and not commercial or industrial use.

In regard to some components manufactured by other companies and

sold by LANDOLL, including but not limited to tires, said Warranty shall

be provided solely by that manufacturing company.

This Warranty applies to products sold in the United States and Canada, and is made expressly in place of all other warranties, expressed or

Implied.