Sony DSC-HX20 HX20, HX20V, DSC-HX30 HX30, HX30V camera Service manual
The DSC-HX20, DSC-HX20V, DSC-HX30 and DSC-HX30V cameras offer a variety of features for capturing high-quality images and videos. These cameras feature a 20x optical zoom lens, a 18.2-megapixel Exmor R CMOS sensor, and a 3.0-inch LCD screen. The DSC-HX30 and DSC-HX30V models also include Wi-Fi connectivity for easy sharing of your photos and videos.
PDF
Download
Document
Advertisement
Advertisement
983465933.pdf Revision History DSC-HX20/HX20V/HX30/HX30V SERVICE MANUAL LEVEL 2 US Model Canadian Model AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Ver. 1.2 2012.06 Internal memory ON BOARD Revised-2 Replace the previously issued SERVICE MANUAL 9-834-659-32 with this Manual. History Contents S.M. Rev. issued — — Ver. Date 1.0 2012.03 Official Release 1.1 2012.05 Revised-1 (A1 12-008) • Addition of SERVICE NOTE. Page 1-6, 1-11, 1-12, 1-13, 1-19 • Revision of EXPLODED VIEWS. Page 2-3, 2-4, 2-5, 2-6, 2-7 • Correction of ACCESSORIES. Page 2-8 • Addition of Flyer Yes 1.2 2012.06 Revised-2 (A2 12-082) • Addition of DSC-HX20. Page 2, 1-5, 1-11, 2-3, 2-6 Yes Photo: DSC-HX30V/BLACK SERVICE NOTE (Check the following note before the service.) – ENGLISH – 1-1. PRECAUTION ON REPLACING THE SY-325 BOARD 1-2. ADDITION OF DESTINATION DATA FILE 1-3. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY 1-4. HOW TO WRITE DATA TO INTERNAL MEMORY 1-5. SELF-DIAGNOSIS FUNCTION 1-6. PROCESS AFTER FIXING FLASH ERROR 1-7. PRECAUTION ON REPLACING THE CABINET (BOTTOM) 1-8. CHECKING THE Wi-Fi FUNCTION 1-9. ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD 1-10. ZOOM MOTOR GEAR BLOCK REPLACING METHOD 1-11. CAM TUBE (B) ASSY REPLACING METHOD 1-12. FINAL INSPECTION ‒ JAPANESE ‒ 1-1. SY-325基板交換時の注意 1-2. Destination Data ファイルの追加について 1-3. 内蔵メモリーのデータコピーおよび消去方法 1-4. 内蔵メモリーへデータを書き戻す方法 1-5. 自己診断機能 1-6. フラッシュエラー発生時の対処法 1-7. キャビネット (底)交換時の注意 1-8. Wi-Fi機能の確認 DIGITAL STILL CAMERA The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DSC-HX20/HX20V/HX30/HX30V_L2 9-834-659-33 Sony Corporation 2012F08-1 © 2012.06 Published by Sony Techno Create Corporation Ver. 1.2 2012.06 The changed portions from Ver. 1.1 are shown in blue. – ENGLISH – – JAPANESE – SPECIFICATIONS Camera 概略仕様 Recording media: Internal Memory (Approx. 105 MB), “Memory Stick Duo” media, SD cards, “Memory Stick Micro” media, microSD memory cards Flash: Flash range (ISO sensitivity (Recommended Exposure Index) set to Auto): Approx. 0.4 m to 7.1 m (1 ft 3 3/4 inches to 23 ft 3 5/8 inches) (W) Approx. 1.5 m to 3.9 m (4 ft 11 1/8 inches to 12 ft 9 5/8 inches) (T) [System] Image device: 7.76 mm (1/2.3 type) Exmor R CMOS sensor Total pixel number of camera: Approx. 18.9 Megapixels Effective pixel number of camera: Approx. 18.2 Megapixels Lens: Sony G 20× zoom lens f = 4.45 mm – 89 mm (25 mm – 500 mm (35 mm film equivalent)) F3.2 (W) – F5.8 (T) While shooting movies (16:9): 27.5 mm – 550 mm* While shooting movies (4:3): 34 mm – 680 mm* * When [Movie SteadyShot] is set to [Standard] SteadyShot: Optical Exposure control: Automatic exposure, Manual exposure, Scene Selection (15 modes) White balance: Automatic, Daylight, Cloudy, Fluorescent 1/2/3, Incandescent, Flash, One Push, White Balance Shift Signal format: For 1080 50i: PAL color, CCIR standards HDTV 1080/50i, 1080/50p specification For 1080 60i: NTSC color, EIA standards HDTV 1080/60i, 1080/60p specification File format: Still images: JPEG (DCF, Exif, MPF Baseline) compliant, DPOF compatible 3D still images: MPO (MPF Extended (Disparity Image)) compliant Movies (AVCHD format): AVCHD format Ver. 2.0 compatible Video: MPEG-4 AVC/H.264 Audio: Dolby Digital 2ch, equipped with Dolby Digital Stereo Creator • Manufactured under license from Dolby Laboratories. Movies (MP4 format): Video: MPEG-4 AVC/H.264 Audio: MPEG-4 AAC-LC 2ch [Wireless LAN] (DSC-HX30/HX30V only) 本体 [システム] Supported format: IEEE 802.11 b/g/n 撮像素子:7.76 mm(1/2.3型) Exmor R CMOSセンサー 総画素数:約1890万画素 カメラ有効画素数:約1820万画素 レンズ:Sony G 20倍ズームレンズ f=4.45 mm ∼ 89 mm (25 mm ∼ 500 mm(35 mmフィ ルム換算値))、F3.2(W)∼ F5.8 (T) 動画撮影時 (16:9):27.5 mm ∼ 550 mm* 動画撮影時 (4:3):34 mm ∼ 680 mm* [ * 動画手ブレ補正]が[スタンダード]のとき 手ブレ補正:光学式 露出制御:自動、マニュアル露出、シーン セレクション (15モード) ホワイトバランス:オート、太陽光、曇天、 蛍光灯1、2、3、電球、フラッシュ、ワ ンプッシュ、ホワイトバランスシフト 信号方式:NTSCカラー、EIA標準方式 記録方式: 静止画記録方式: JPEG(DCF、Exif、MPF Baseline) 準拠、DPOF対応 3D静止画記録方式:MPO(MPF Extended(立体視))準拠 動画記録方式 (AVCHD方式): AVCHD規格 Ver.2.0準拠 映像:MPEG-4 AVC/H.264 音声:Dolby Digital 2ch ドルビーデジタルステレオクリエー ター搭載 ・ドルビーラボラトリーズからの実施権に基づき 製造されています。 動画記録方式 (MP4方式): 映像:MPEG-4 AVC/H.264 音声:MPEG-4 AAC-LC 2ch AC Adaptor AC-UB10/UB10B Power requirements: AC 100 V to 240 V, 50 Hz/60 Hz, 70 mA Output voltage: DC 5 V, 0.5 A Operating temperature: 0 °C to 40 °C (32 °F to 104 °F) Storage temperature: –20 °C to +60 °C (–4 °F to +140 °F) Dimensions: Approx. 50 mm × 22 mm × 54 mm (2 inches × 7/8 inches × 2 1/4 inches) (W/H/D) Mass: For the USA and Canada: Approx. 48 g (1.7 oz) For countries or regions other than the USA and Canada: Approx. 43 g (1.5 oz) [Input and Output connectors] HDMI connector: HDMI mini jack Micro USB connector: USB communication USB communication: Hi-Speed USB (USB 2.0) [Screen] LCD screen: 7.5 cm (3.0 type) TFT drive Total number of dots: 921 600 dots Rechargeable battery pack NP-BG1 Used battery: Lithium-ion battery Maximum voltage: DC 4.2 V Nominal voltage: DC 3.6 V Maximum charge voltage: DC 4.2 V Maximum charge current: 1.44 A Capacity: typical: 3.4 Wh (960 mAh) minimum: 3.3 Wh (910 mAh) [Power, general] Power: Rechargeable battery pack NP-BG1, 3.6 V NP-FG1 (sold separately), 3.6 V AC Adaptor AC-UB10/UB10B, 5V Power consumption (during shooting): 1.1 W Operating temperature: 0 °C to 40 °C (32 °F to 104 °F) Storage temperature: –20 °C to +60 °C (–4 °F to +140 °F) Dimensions (CIPA compliant): 106.6 mm × 61.9 mm × 34.6 mm (4 1/4 inches × 2 1/2 inches × 1 3/8 inches) (W/H/D) Mass (CIPA compliant) (including NPBG1 battery pack, “Memory Stick Duo” media): Approx. 254 g (9.0 oz) Microphone: Stereo Speaker: Monaural Exif Print: Compatible PRINT Image Matching III: Compatible Design and specifications are subject to change without notice. Model information table Model DSC-HX20 DSC-HX20V DSC-HX30 DSC-HX30V Destination AEP US E AEP, E, AUS UK CH US, J CND, E, KR HK Color system PAL NTSC NTSC PAL PAL PAL NTSC NTSC PAL GPS TransferJet • Abbreviation AUS : Australian model CH : Chinese model CND : Canadian model HK : Hong Kong model J: Japanese model KR : Korea model DSC-HX20/HX20V/HX30/HX30V_L2 –2– 記録メディア:内蔵メモリー 約105 MB、 “メモリースティック デュオ”、SD カード、“メモリースティック マイク ロ”、microSD メモリーカード フラッシュ:撮影範囲 (ISO感度(推奨露 光指数)がオートのとき) 約0.4 m∼ 7.1 m (W)/約1.5 m∼ 3.9 m(T) [入出力端子] HDMI端子:HDMIミニ端子 マイクロUSB端子:USB通信 USB通信:Hi-Speed USB(USB 2.0) [ワイヤレスLAN] 対応規格:IEEE 802.11b/g/n ACアダプター AC-UB10/UB10B 定格入力:AC 100 V ∼ 240 V、 50 Hz/60 Hz、70 mA 定格出力:DC 5 V、0.5 A 動作温度:0 ℃∼ 40 ℃ 保存温度:−20 ℃∼ +60 ℃ 外形寸法:約50 mm×22 mm×54 mm (幅×高さ×奥行き) 本体質量:約48 g [モニター] 液晶モニター: 7.5 cm(3.0型)、TFT駆動 総ドット数:921 600ドット [電源・その他] 電源:リチャージャブルバッテリー パックNP-BG1、3.6 V NP-FG1(別売)、3.6 V ACアダプター AC-UB10/UB10B、 5V 消費電力 (撮影時): 約1.1 W 動作温度:0 ℃∼ 40 ℃ 保存温度:−20 ℃∼ +60 ℃ 外形寸法 (CIPA準拠): 106.6 mm×61.9 mm×34.6 mm (幅×高さ×奥行き) 本体質量 (CIPA準拠) (バッテリー NP-BG1、“メモリース ティック デュオ”を含む): 約254 g マイクロホン:ステレオ スピーカー:モノラル Exif Print:対応 PRINT Image Matching III:対応 リチャージャブルバッテリー パックNP-BG1 使用電池:リチウムイオン蓄電池 最大電圧:DC 4.2 V 公称電圧:DC 3.6 V 容量:3.4 Wh(960 mAh) 本機や付属品の仕様および外観は、改良 のため予告なく変更することがあります が、ご了承ください。 – ENGLISH – – JAPANESE – Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries according to the instructions. 注意 電池の交換は,正しく行わないと破裂する恐れがあります。 電池を交換する場合には必ず同じ型名の電池又は同等品と 交換してください。 使用済み電池は,取扱指示に従って処分してください。 SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. サービス,点検時には次のことにご注意ください。 1. 注意事項をお守りください。 サービスのとき特に注意を要する個所については,キャビ ネット,シャーシ,部品などにラベルや捺印で注意事項を 表示しています。これらの注意書き及び取扱説明書等の注 意事項を必ずお守り下さい。 2. 指定部品のご使用を セットの部品は難燃性や耐電圧など安全上の特性を持った ものとなっています。従って交換部品は,使用されていた ものと同じ特性の部品を使用して下さい。特に回路図,部 品表に0印で指定されている安全上重要な部品は必ず指定 のものをご使用下さい。 3. 部品の取付けや配線の引きまわしはもとどおりに 安全上,チューブやテープなどの絶縁材料を使用したり, プリント基板から浮かして取付けた部品があります。また 内部配線は引きまわしやクランパによって発熱部品や高圧 部品に接近しないよう配慮されていますので,これらは必 ずもとどおりにして下さい。 4. サービス後は安全点検を サービスのために取外したネジ,部品,配線がもとどおり になっているか,またサービスした個所の周辺を劣化させ てしまったところがないかなどを点検し,安全性が確保さ れていることを確認して下さい。 5. チップ部品交換時の注意 ・ 取外した部品は再使用しないで下さい。 ・ タンタルコンデンサのマイナス側は熱に弱いため交換時 は注意して下さい。 6. フレキシブルプリント基板の取扱いについて ・ 半田こてのこて先温度は約350℃に設定してください。 ・ 同一パターンに何度もコテ先を当てないで下さい。 (3回 以内) ・ パターンに力が加わらないよう注意して下さい。 SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit Board Repairing • Set the soldering iron tip temperature to 350 °C approximately. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. DSC-HX20/HX20V/HX30/HX30V_L2 UNLEADED SOLDER This unit uses unleaded solder. Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Be careful to the following points to solder or unsolder. • Set the soldering iron tip temperature to 350 °C approximately. If cannot control temperature, solder/unsolder at high temperature for a short time. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing unleaded solder and leaded solder will cause detachment phenomenon. –3– 無鉛半田について 本機には無鉛半田が使用されています。 無鉛半田を使用している基板には,無鉛 (Lead Free)を意味する レッドフリーマークがプリントされています。 (注意:基板サイズによっては,無鉛半田を使用していてもレッ ドフリーマークがプリントされていないものがありま す) :レッドフリーマーク 無鉛半田は,下記の点に注意して使用してください。 ・半田こてのこて先温度は約350℃に設定してください。 温度調節が無理な場合は,高温短時間で作業を行ってくだ さい。 注意: 半田こてを長く当てすぎると,基板のパターン (銅 箔)がはがれてしまうことがありますので,注意して ください。また,従来の半田よりも粘性が強いため, IC端子などが半田ブリッジしないように注意してく ださい。 ・半田こてのこて先は,必ず無鉛半田用と有鉛半田用に分け て管理してください。 無鉛半田と有鉛半田が混在すると剥離現象が発生してしま います。 1. SERVICE NOTE – ENGLISH – 1-1. PRECAUTION ON REPLACING THE SY-325 BOARD 1-2. ADDITION OF DESTINATION DATA FILE DESTINATION DATA If the Destination Data file included in the Adjust manual is old, “DESTINATION DATA WRITE” cannot be executed in some cases. In that case, download a new Destination Data file from the TISS homepage according to the following procedure. When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting. Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”. Note 1: To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed. Install the Adjust manual of the DSC-WX50 series in advance. Note 2: The actual image may differ from the image shown above. RESTORE DATA When you replace to the repairing board, get the data from the former one. Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data. The data getting for this model is as follows. • USB SERIAL No. • Wide Limit Data • Angular Velocity Sensor Sensitivity adjustment • AWB standard data input & check, Color reproduction check • Strobe adjustment 1) If the Destination Data file in the Adjust manual in use is old, the window shown in Fig. 1 is displayed. Click the [OK] button. Regarding the PlayMemories Home PlayMemories Home has been written in internal memory. SY-325 board for service is supplied with written the PlayMemories Home. Fig. 1 USB SERIAL No. 2) The Destination Data Write window opens. Check the version of the Destination Data file retained in the Adjust manual. The set is shipped with a unique ID (USB Serial No.) written in it. This ID has not been written in a new board for service, and therefore it must be entered after the board replacement. Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”. Angular Velocity Sensor When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor (SE401). Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity adj”. SY-325 BOARD (SIDE A) Destination Ver. window SE401 Type A: YP Type B: YP Y: YAW sensor sensitivity P: PITCH sensor sensitivity Note: The sensor sensitivity of SE401 of SY-325 board is written only repair parts. DSC-HX20/HX20V/HX30/HX30V_L2 1-1 – ENGLISH – 3) Search the model whose new Destination Data file you want to get on the TISS homepage. When the Destination Data file has been updated, a file with a name “Destination File For ‘model name’.zip” is registered. 6) Click the [File Update] button in the window. (Example) Destination File For DSC-WX50.zip Furthermore, the version supported by the Destination Data file is shown in the Remarks column. Note : If the Destination Data file has not been updated, contact the Service Headquarters. 7) A file selection screen opens. Select the Destination Data file to be added and click the [Open] button. 4) Download the Destination Data file of the relevant model and unzip the file. 8) When the file has been successfully added, the following window opens. 9) Check the Destination Ver. window and confirm that the version has been updated. 5) Execute “DESTINATION DATA WRITE” in the Adjust tab of the Adjust manual. Click the [START] button. Destination Ver. window DSC-HX20/HX20V/HX30/HX30V_L2 1-2 – ENGLISH – 1-3. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY 1-4. HOW TO WRITE DATA TO INTERNAL MEMORY The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.) Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera. This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement. To change settings is enabled with using the writing enabler tool (Write Enable Tool) on the Adjust Manual is activating from the Adjust Station. Note 1:When replacing the SY-325 board, erase the data in internal memory of the board before replacement. Note 2:When replacing the SY-325 board, execute formatting and initialize the internal memory after replacement. Data writing method 1) Start the Adjust Manual from the Adjust Station. Method for Copying the Data in Internal Memory 2) Click Copy (Write Enable Tool) button. 3) Click “Activate Write Enable Mode” button. Copies all images in the internal memory to a memory card. 1. Insert a memory card with sufficient free capacity into the camera. 2. MENU (Settings) (Memory Card Tool) [Copy] [OK] Notes Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data. Images cannot be copied individually. The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the memory card after copying, then format the internal memory ([Format] in [Internal Memory Tool]). The data will be copied to the recording folder that is currently being used, with a number one higher than the largest data number in that folder. Method for Formatting the Internal Memory or “Memory Stick Duo” media Format 4) Upon completion of the setting change, the following message will be displayed. Formats the memory card or the internal memory. When you use a memory card with this camera for the first time, it is recommended to format the card using the camera for stable performance of the memory card before shooting. Note that formatting permanently erases all data on the memory card, and is unrecoverable. Save precious data on a computer, etc. 1. MENU (Settings) (Memory Card Tool) or (Internal Memory Tool) [Format] [OK] Note Note that formatting permanently erases all data including even protected images. 5) Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage). 6) Write the data read out into the PC to the internal memory of the camera. 7) Disconnect the PC from the camera, and turn off the camera. Note: By turning off the camera, the write enable setting is reset. DSC-HX20/HX20V/HX30/HX30V_L2 1-3 – ENGLISH – 1-5. SELF-DIAGNOSIS FUNCTION 1-5-3. Self-diagnosis Code Table Self-diagnosis Code 1-5-2. Self-diagnosis Display When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the LCD screen what to do. Details of the self-diagnosis functions are provided in the Instruction manual. When problems occur while the unit is operating, the LCD screen shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in which the problem occurred, and “detailed code” of the problem. Repaired by: 1-5-1. Self-diagnosis Function Block Function Detailed Code LCD screen Correction The internal memory has experienced a Turn the power off and on again. media error. The internal memory has experienced a Format the internal memory. format error. C 1 3 0 1 Blinks at 3.2 Hz C Repaired by: Symptom/State 32 Block 00 Detailed Code Format the memory card. Memory card is broken. Insert a new memory card. Memory card type error. Insert a supported memory card. The camera cannot read or write data on Turn the power off and on again, or taking out and inserting the memory card several times. the memory card. Trouble with hardware. Turn the power off and on again. C 3 2 0 1 E 4 1 0 0 * Abnormality of network control. Turn power off and turn power on again. E 4 1 0 1 * Abnormality of network control device. Turn power off and turn power on again. E Refer to “1-5-3. Self-diagnosis Code Table”. C : Corrected by customer Indicates the appropriate E : Corrected by service step to be taken. engineer E.g. 13 ....Format the “memory card”. 32 ....Turn on power again. Memory card is unformatted. 6 1 0 0 Difficult to adjust focus. (Cannot initialize focus) Retry turn the power on by the power switch. If it does not recover, check the focus reset sensor of lens block (pin ej, el of CN405 on the SY-325 board). If it is OK, check the focus motor drive IC (IC401 on the SY-325 board). Zoom operations fault. (Cannot initialize zoom lens.) Retry turn the power on by the power switch. Check the zoom reset sensor of lens block (pin wa of CN405 on the SY-325 board) when zooming is performed when the zoom button is operated. If it is OK, check the zoom motor drive IC (IC401 on the SY-325 board). E 6 1 1 0 E 6 1 3 0 E 6 2 0 2 E 6 2 1 0 E 6 2 1 1 Lens overheating (PITCH). Check the HALL element (PITCH) of optical image stabilizer (pin 9, qa of CN405 on the SY-325 board). If it is OK, check PITCH angular velocity sensor (SE401 on the SY-325 board) peripheral circuits. E 6 2 1 2 Lens overheating (YAW). Check the HALL element (YAW) of optical image stabilizer (pin qk, w; of CN405 on the SY-325 board). If it is OK, check YAW angular velocity sensor (SE401 on the SY-325 board) peripheral circuits. E 6 2 2 0 Abnormality of thermistor. E 9 1 0 1 Check the OIS temp sensor of optical image stabilizer (pin 8 of CN405 on the SY-325 board). Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit. (Note 1) E 9 4 0 0 Internal memory fault. Reset position detection error on the stepTurn power off and turn power on again. per iris initializing. Check or replacement of the IC for steadyshot (IC401 on the SY-325 Abnormality of IC for steadyshot. board). Check or replacement of the IC for steadyshot (IC401 on the SY-325 Lens initializing failure. board). E 9 5 0 0 GPS hardware error. E 9 5 0 1 Acceleration sensor hardware error. (GPS hardware error) E 9 5 0 2 Electronic compass hardware error. (GPS hardware error) Inspect the internal memory (IC211 on the SY-325 board). Check whether the RL-130 flexible board of connected between SY-325 board and RL-129 board is broken, and check whether it is inserted imperfectly. If there is no problem the coaxial cable or flexible board, inspect or replacement of the SY-325 or RL-129 board. Check whether the RL-130 flexible board of connected between SY-325 board and RL-129 board is broken, and check whether it is inserted imperfectly. If there is no problem the coaxial cable or flexible board, inspect or replacement of the SY-325 or RL-129 board. Check whether the RL-130 flexible board of connected between SY-325 board and RL-129 board is broken, and check whether it is inserted imperfectly. If there is no problem the coaxial cable or flexible board, inspect or replacement of the SY-325 or RL-129 board. Note 1: After repair, be sure to perform “1-6. PROCESS AFTER FIXING FLASH ERROR”. Note 2: Functions of codes with * mark are not provided in this unit. DSC-HX20/HX20V/HX30/HX30V_L2 1-4 Ver. 1.2 2012.06 The changed portions from Ver. 1.1 are shown in blue. – ENGLISH – 1-6. PROCESS AFTER FIXING FLASH ERROR 1-7. PRECAUTION ON REPLACING THE CABINET (BOTTOM) When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated. Flash error code can be on the HOME screen. 1-7-1. Precaution on ordering the CABINET (BOTTOM) The model display adopts the laser printing method. Therefore, the Cabinet (Bottom) for replacement differs depending on the destination. As similar displays are provided, choose the suitable one for order. Method for Initializing the Flash Error Code Reset Flash Error using the Flash Error Repair Tool Ver_[].[].exe. DSC-HX30V (US Model) DSC-HX30V (CND Model) DSC-HX30V (HK Model) Serial No. Part No. Description A-1878-204-A CABINET (BOTTOM) Serial No. Part No. Description A-1878-205-A CABINET (BOTTOM) Serial No. Part No. Description A-1878-211-A CABINET (BOTTOM) (BLACK) A-1878-212-A CABINET (BOTTOM) (BROWN) DSC-HX30V (TW Model) DSC-HX30V (KR Model) DSC-HX30V (J Model) Serial No. Part No. Description A-1878-207-A CABINET (BOTTOM) (BLACK) A-1878-210-A CABINET (BOTTOM) (BROWN) Serial No. Part No. Description A-1878-206-A CABINET (BOTTOM) (BLACK) A-1878-209-A CABINET (BOTTOM) (BROWN) Serial No. Part No. Description A-1878-203-A CABINET (BOTTOM) (BLACK) A-1878-208-A CABINET (BOTTOM) (BROWN) DSC-HX30 (CH Model) DSC-HX20V (US Model) DSC-HX20V (AEP, UK, E, AUS Model) (BLACK) Serial No. Part No. Description A-1878-213-A CABINET (BOTTOM) (BLACK) A-1878-214-A CABINET (BOTTOM) (BROWN) Serial No. Part No. Description A-1878-215-A CABINET (BOTTOM) Serial No. Part No. Description A-1878-218-A CABINET (BOTTOM) (BLACK) DSC-HX20V (AEP, UK, E Model) (BROWN) DSC-HX20V (AEP Model) (BLACK) DSC-HX20V (E Model) Serial No. Part No. Description A-1878-224-A CABINET (BOTTOM) (BROWN) Serial No. Part No. Description A-1878-216-A CABINET (BOTTOM) (BLACK) A-1878-217-A CABINET (BOTTOM) (BROWN) DSC-HX20 (AEP Model) (BLACK) Serial No. Part No. Description A-1891-788-A CABINET (BOTTOM) DSC-HX20/HX20V/HX30/HX30V_L2 1-5 Note: After replacing the Cabinet (Bottom) , the serial number for it will be changed to the one exclusive for service use. Inform a customer of the serial number change and change the serial number in the repair data. Serial No. Part No. Description A-1878-220-A CABINET (BOTTOM) Ver. 1.1 2012.05 The changed portions from Ver. 1.0 are shown in blue. – JAPANESE – – ENGLISH – 1-8. CHECKING THE Wi-Fi FUNCTION 1-1. SY-325基板交換時の注意 Perform the following procedure to check the Wi-Fi function. 仕向けデータ Required equipment: Windows personal computer with Wi-Fi interface 補修用基板と交換する時,補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。 Adjust StationからAdjust Manualを起動させて「DESTINATION DATA WRITE」を実行させてください。 1. 2. 3. 4. 5. Turn on the power of the unit. Touch the Play button to display the captured image. Touch the Wi-Fi button to display the smartphone transfer screen. Touch “This image” on the smartphone transfer screen to open the “Wi-Fi Standby…” screen. When preparation for Wi-Fi has been completed, the “It functions as an access point. ” screen opens and a password for Wi-Fi connection is displayed. リストアデータ 補修用基板と交換する時,交換前の基板よりデータを取得してください。 データの取得はAdjust StationからAdjust Manualを起動させて「RESTORE DATA」を実行させてください。 本機で取得されるデータは下記になります。 ・ USB SERIAL No. ・ Wide Limit Data ・ Angular Velocity Sensor sensitivity adjustment ・ AWB standard data input & check, Color reproduction check ・ Strobe adjustment Or when preparation for Wi-Fi has been completed, the following screen opens and a password for Wi-Fi connection is displayed. View on Smartphone Wi-Fi PlayMemories Homeについて 本機の内蔵メモリー内にはPlayMemories Homeが書き込まれています。 補修用SY-325基板は,PlayMemories Homeが書き込まれた状態で供給されます。 Awaiting connection to the smartphone. If functions as an access point. USBシリアルNo. SSID : DIRECT-E6C0:DSC-XXXXX セットは,1台毎に異なる固有のID(USB Serial No.)を書き込んだ後,出荷されています。 新品の補修用基板には,このIDが書き込まれていないので,基板交換後にIDを入力する必要があります。 Adjust StationからAdjust Manualを起動させて「USB SERIAL No. INPUT」を実行させてください。 Password : XXXXXXXX Device Name : DSC-XXXXX 角速度センサ 補修用基板と交換する時,角速度センサ(SE401)の感度表示を書き留めてください。 Adjust StationからAdjust Manualを起動させて「Angular velocity sensor sensitivity adj.」を実行させてください。 6. Confirm on the personal computer that the unit is detected as a connectable wireless network. 7. To further confirm that the unit is connectable, connect the unit to the personal computer and select “Network and Internet” → “Manage Wireless Networks” from Control Panel to open the network connection list. The unit is included in the list. SY-325 BOARD (SIDE A) SE401 Type A: YP Type B: YP Y: YAW 感度表示 P: PITCH 感度表示 Note:SY-325基板のSE401感度表示は補修用基板にしか記載されておりません。 DSC-HX20/HX20V/HX30/HX30V_L2 1-6 – JAPANESE – 3) TISSホームページにて,新しい Destination Data ファイルを入手したい機種を検索する。 1-2. Destination Data ファイルの追加について Destination Data ファイルが更新されている場合, 「Destination File For 機種名 .zip」という名称のファイルが登録されてい る。 Adjust manual に含まれる Destination Data ファイルが古い場合, 「DESTINATION DATA WRITE」が実行できないことがあります。 その場合は,下記の手順を参考にして,TISS ホームページより新しい Destination Data ファイル を入手してください。 (例) Destination File For DSC-WX50.zip Note1: この機種で仕向け設定を行うには,DSC-WX50シリーズの Adjust manual がインストールされている必要があります。 先に DSC-WX50 シリーズの Adjust manual をインストールしてください。 また,Remarks欄にはこの Destination Data ファイルが対応するバージョンが記載されています。 Note 2: 手順中の画像は実際と異なる場合があります。 Note:バージョンが更新されていなかった場合は,サービスヘッドクォーターへお問い合わせください。 1) 使用している Adjust manual の Destination Data ファイルが古い場合,Fig. 1 のようなウインドウが表示される。 [OK] ボタンをクリックする。 Fig. 1 2) Destination Data Write ウインドウが表示される。 Adjust manual の保持している Destination Data ファイル のバージョンを確認する。 4) 該当機種の Destination Data ファイルをダウンロードし,解凍する。 Destination Ver. ウインドウ 5) Adjust manual の Adjust タブにある,「DESTINATION DATA WRITE」を実行する。 [START] ボタンをクリックする。 DSC-HX20/HX20V/HX30/HX30V_L2 1-7 – JAPANESE – 6) ウインドウ内の [File Update] ボタンをクリックする。 1-3. 内蔵メモリーのデータコピーおよび消去方法 内蔵メモリーのデータコピーまたは消去はホーム画面の操作から実行可能です。 (消去する場合は内蔵メモリーの初期化を行います。) Note1:SY-325基板交換の際は,基板交換前に内蔵メモリーのデータを消去して下さい。 Note2:SY-325基板交換の際は,基板交換後に内蔵メモリーのフォーマットおよび初期化を実行して下さい。 内蔵メモリーのコピー方法 ॥আش ওঔজشप੶ஈखञ൸ؚ॑ওঔজشढ़ॻشपฐ॥আشखऽघ؛ ౄীऩ૬ऌઍभँॊওঔজشढ़॑ॻشমਃपোोॊ 0(18 7) ファイルを選択する画面が出るので,追加する Destination Data ファイルを選択し,[開く] ボタンをクリックする。 قਝك قওঔজشढ़شॶॻشঝك ن॥আهش ن2.ه রఙभ ओିਔ ౄীपౄਗ਼खञংॵॸজ॑شओઞ৷ऎटऔः؛ଋभऩःংॵॸজ॑شઞ৷खथ൸ই॓ॖঝ॑ ॥আشघॊधؚংॵॸজشજोभञीॹ॑ॱشૡଛदऌऩऊढञॉ॑ॱشॹؚघॊउजोऋँ ॉऽघ؛ ൸ओधभ॥আشमदऌऽच॒؛ ॹ॑ॱش॥আشखथुؚওঔজشभॹॱشमచऔोऽच॒؛ওঔজشभઍ॑ுघ ॊपमؚ॥আشपওঔজشढ़॑ॻشম৬ऊैॉमङखنؚওঔজشॶشঝهभنইज़ش ঐॵॺ॑هষढथऎटऔः؛ ॹ॑ॱش॥আشघॊधؚਠभखथःॊ੶ஈইज़ঝॲपਈभই॓ॖঝಀद॥আشऔो ऽघ؛ 内蔵メモリー、もしくはメモリーカードのフォーマット方法 ইज़شঐॵॺ 8) ファイルの追加が成功すると,下記のような画面が出る。 ওঔজشढ़ؚॻشऽञमওঔজ॑شইज़شঐॵॺੂق৲كखऽघ؛ ওঔজشढ़ॻشभ॑औचॊञीपؚওঔজشढ़॑ॻشমਃदमगीथउઞःपऩॊৃ়पमؚ ऽङؚমਃदইज़شঐॵॺघॊऒध॑उघघीखऽघ؛ইज़شঐॵॺघॊधؚওঔজشढ़ॻشप੶ஈऔ ोथःॊ৸थभॹॱشमுऔोؚ੪पರघऒधमदऌऽच॒؛পજऩॹॱشमঃ९॥থऩनप৳ோख थउःथऎटऔः؛ 0(18 قਝك نইज़شঐॵॺه قওঔজشढ़شॶॻشঝؚكऽञम قওঔজشॶشঝك রఙभ ओିਔ 9) Destination Ver. ウインドウを確認し,バージョンが更新されていることを確認する。 ইज़شঐॵॺघॊधؚউটॸॡॺखथँॊ൸ुஅीथؚघसथभॹॱشऋுऔोؚ੪पರचऽ च॒؛ Destination Ver. ウインドウ DSC-HX20/HX20V/HX30/HX30V_L2 ن2.ه 1-8 – JAPANESE – 1-4. 内蔵メモリーへデータを書き戻す方法 1-5. 自己診断機能 通常は,PCからカメラの内蔵メモリへデータを書き込むことはできない設定になっています。 基板交換後などに,内蔵メモリへデータを書き戻す場合には,この設定を一時的に変更する必要があります。 設定の変更は,Adjust StationからAdjust Manualを起動させて書き込み許可ツール(Write Enable Tool)を使用します。 1-5-1. 自己診断機能について 1-5-2. 自己診断表示 本機の動作に不具合が生じたとき,自己診断機能が働き,LCD 画面に,どう処置したらよいか判断できる表示を行います。自 己診断機能については取扱説明書にも掲載されています。 本機の動作に不具合が生じたとき,LCD画面にアルファベッ トと4桁の数字が表示され,3.2Hzで点滅します。この5文字の 表示によって対応者分類および不具合の生じたブロックの分 類,不具合の詳細コードを示します。 書き戻し方法 1) Adjust StationからAdjust Manualを起動する。 2) (Write Enable Tool)ボタンをクリックする。 3) Activate Write Enable Mode ボタンをクリックする。 LCD画面 3.2 Hz点滅 C 対応者分類 C :お客さま自身で対応 E :サービスエンジニア で対応 4) 設定の変更が終了すると,次のメッセージが表示されますので OK ボタンをクリックする。 5) ドライバを元に戻して、カメラとPCをマスストレージ接続する。 6) PCに読み出しておいたデータをカメラの内蔵メモリに書き込む。 7) カメラとPCの接続を解除し,カメラの電源をOFFにする。 注意:カメラの電源をOFFにすることにより,書き込み許可の設定が解除されます。 DSC-HX20/HX20V/HX30/HX30V_L2 1-9 32 ブロック分類 00 詳細コード 対応方法の違いにより分類 「1-5-3. 自己診断コード表」を参照 例 13・・・メモリーカードをフォーマットする 32・・・電源を入れ直す – JAPANESE – 1-5-3. 自己診断コード表 1-6. フラッシュエラー発生時の対処法 自己診断コード 対 応 者 C ブロック 機能 1 3 症状/状態 詳細 コード 0 1 本機はフラッシュエラー(自己診断コードE:91:01)が発生した場合,高電圧による異常を防止するために自動的にフラッシュ充 電および発光禁止の設定になります。 フラッシュエラー発生後はエラーの解除を行う必要があります。エラーの解除はホーム画面から行います。 対応/方法 内蔵メモリーに メディアエラー があっ 電源を入れ直す。 た。 内蔵メモリにフォーマットエラーが 内蔵メモリをフォーマットする。 あった。 フォーマットしていないメモリーカー メモリーカードをフォーマットする。 ドを入れた。 メモリーカードが壊れている。 フラッシュエラーの解除方法 Flash Error Repair Tool Ver_[].[].exe を使用して Flash Error を解除してください。 新しいメモリーカードに交換する。 メモリーカードのタイプエラーを検出 規格内のメモリーカードを挿入する。 した。 電源の入れ直し,またはメモリーカードの挿し/外しを数回 メモリーカードが読み/書きできない。 試す。 C 3 2 0 1 ハードウェアトラブルを検出した。 電源を入れ直す。 E 4 1 0 0* ネットワーク制御マイコンの異常。 電源を入れ直す。 E 4 1 0 1* ネットワーク制御デバイスの異常。 電源を入れ直す。 0 フォーカスが合いにくい。 0 (フォーカスの初期化ができない) 操作スイッチの電源を入れ直す。 復帰しない場合はレンズブロックのフォーカスリセットセン サ(SY-325基板CN405 ej, elピン)を点検する。異常なければ フォーカスモータ駆動IC(SY-325基板IC401)を点検する。 E 6 1 ズーム動作の異常。 (ズームレンズの初期化ができない) 操作スイッチの電源を入れ直す。 ズームボタンを操作したときにズーム動作をすればレンズブ ロックのズームリセットセンサ(SY-325基板CN405 waピン) を点検する。異常なければズームモータ駆動IC(SY-325基板 IC401)を点検する。 E 6 1 1 0 E 6 1 3 0 ステッパIRISイニシャル時リセット位置 電源を入れ直す。 検出異常 E 6 2 0 2 手振れ補正用ICの異常。 手振れ補正用IC(SY-325基板IC401)を点検または交換する。 1 手振れ補正用ICの異常。 0 (レンズ初期化異常) 手振れ補正用IC(SY-325基板IC401)を点検または交換する。 E 6 2 光学手振れ補正ブロックのホール素子(PITCH) (SY-325基板 CN405 9,qaピン)を点検する。 異常なければPITCH角速度センサ(SY-325基板SE401)周辺の 回路を点検する。 光学手振れ補正ブロックのホール素子(YAW) (SY-325基板 CN405 qk,w;ピン)を点検する。 異常なければYAW角速度センサ(SY-325基板SE401)周辺の 回路を点検する。 光学手振れ補正ブロックの温度センサ(SY-325基板CN405 を点検する。 8ピン) E 6 2 1 1 レンズオーバーヒート(PITCH) E 6 2 1 2 レンズオーバーヒート(YAW) E 6 2 2 0 サーミスタの異常。 E 9 1 0 1 フラッシュの充電異常。 フラッシュユニットを点検または交換する。(Note 1) E 9 4 0 0 内蔵メモリーの書き込み/消去動作不良 内蔵メモリー(SY-325基板IC211)を点検する。 E 9 5 0 0 GPSハードウェア異常 E 9 5 0 1 加速度センサーハードウェア異常 (GPSハードウェア異常) E 9 5 0 2 地磁気センサーハードウェア異常 (GPSハードウェア異常) SY-325基板とRL-129基板をつないでいるRL-130フレキシブ ル基板が切れていないか,また完全に挿入されているかを点 検する。フレキシブル基板に問題がない場合は,SY-325基板 またはRL-129基板の点検または交換をする。 SY-325基板とRL-129基板をつないでいるRL-130フレキシブ ル基板が切れていないか,また完全に挿入されているかを点 検する。フレキシブル基板に問題がない場合は,SY-325基板 またはRL-129基板の点検または交換をする。 SY-325基板とRL-129基板をつないでいるRL-130フレキシブ ル基板が切れていないか,また完全に挿入されているかを点 検する。フレキシブル基板に問題がない場合は,SY-325基板 またはRL-129基板の点検または交換をする。 Note 1:交換後は,必ず「1-6. フラッシュエラー発生時の対処法」を行って下さい。 Note 2:*マークのコードは本機には実装されていない機能です。 DSC-HX20/HX20V/HX30/HX30V_L2 1-10 Ver. 1.2 2012.06 The changed portions from Ver. 1.1 are shown in blue. – JAPANESE – 1-7. キャビネット (底)交換時の注意 1-8. Wi-Fi機能の確認 1-7-1. キャビネット(底) 注文時の注意 Wi-Fi 機能を確認するときは以下の手順で行ってください。 機種の表示部はレーザー印字方式を採用しております。 この為,交換用のキャビネット (底)は機種,仕向けにより異な ります。類似の表示もありますので,該当するものを選んで注 文してください。 DSC-HX30V (US 仕向) 注意: キャビネット(底)交換後はシリアルナンバーがサービス 専用のシリアルナンバーに変更されます。お客様への案 内と修理データのシリアルナンバー変更を行ってくださ い。 用意する機器: Wi-Fi接続の可能なWindowsパソコン 1. 2. 3. 4. 5. DSC-HX30V (HK 仕向) DSC-HX30V (CND 仕向) 本機の電源を入れる。 再生ボタンをタッチして撮影済みの画像を表示する。 Wi-Fiボタンをタッチするとスマートフォン転送画面が表示される。 スマートフォン転送画面から「この画像」をタッチすると「Wi-Fi準備中」の画面に切り替わる。 Wi-Fi準備が完了すると「アクセスポイントとして動作中」という画面に切り替わり、Wi-Fi接続のためのパスワードが表示される。 または Wi-Fi準備が完了すると以下の画面に切り替わり、Wi-Fi接続のためのパスワードが表示される。 シリアルナンバー Part No. Description A-1878-204-A CABINET (BOTTOM) シリアルナンバー Part No. Description A-1878-205-A CABINET (BOTTOM) DSC-HX30V (KR 仕向) DSC-HX30V (TW 仕向) シリアルナンバー ࠬࡑ࠻ࡈࠜࡦォㅍ Part No. Description A-1878-211-A CABINET (BOTTOM) (BLACK) A-1878-212-A CABINET (BOTTOM) (BROWN) Wi-Fi ࠬࡑ࠻ࡈࠜࡦߩធ⛯ࠍᓙߜฃߌߡ߹ߔ ࠕࠢࠬࡐࠗࡦ࠻ߣߒߡേਛ DSC-HX30V (J 仕向) SSID : DIRECT-zIC0:DSC-XXXXX ࡄࠬࡢ࠼ : XXXXXXXX ᯏེฬ⒓ シリアルナンバー シリアルナンバー シリアルナンバー Part No. Description A-1878-207-A CABINET (BOTTOM) (BLACK) A-1878-210-A CABINET (BOTTOM) (BROWN) Part No. Description A-1878-206-A CABINET (BOTTOM) (BLACK) A-1878-209-A CABINET (BOTTOM) (BROWN) Part No. Description A-1878-203-A CABINET (BOTTOM) (BLACK) A-1878-208-A CABINET (BOTTOM) (BROWN) DSC-HX30 (CH 仕向) DSC-HX20V (US 仕向) DSC-HX20V (AEP, UK, E, AUS 仕向) (ブラック) シリアルナンバー シリアルナンバー Part No. Description A-1878-215-A CABINET (BOTTOM) Part No. Description A-1878-218-A CABINET (BOTTOM) (BLACK) DSC-HX20V (AEP, UK, E 仕向) (ブラウン) DSC-HX20V (AEP 仕向) (ブラック) DSC-HX20V (E 仕向) シリアルナンバー シリアルナンバー Part No. Description A-1878-220-A CABINET (BOTTOM) 6. 7. シリアルナンバー Part No. Description A-1878-213-A CABINET (BOTTOM) (BLACK) A-1878-214-A CABINET (BOTTOM) (BROWN) Part No. Description A-1878-224-A CABINET (BOTTOM) (BROWN) シリアルナンバー Part No. Description A-1878-216-A CABINET (BOTTOM) (BLACK) A-1878-217-A CABINET (BOTTOM) (BROWN) DSC-HX20 (AEP 仕向) (ブラック) シリアルナンバー Part No. Description A-1891-788-A CABINET (BOTTOM) DSC-HX20/HX20V/HX30/HX30V_L2 : DSC-XXXXX 1-11 パソコン側で接続可能なワイヤレスネットワークとして、本機が検出されることを確認する。 さらに接続可能なことを確認したい場合には本機とパソコンを接続後、コントロールパネルの「ネットワークとインターネット」 →「ワイヤレスネットワークの管理」からネットワーク接続リストを開くと、リストに本機が表示される。 Ver. 1.1 2012.05 The changed portions from Ver. 1.0 are shown in blue. 1-9. ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD 1-10. ZOOM MOTOR GEAR BLOCK REPLACING METHOD Removal Turn on the power switch and extend the lens (TELE end). Detach the battery. Apply alcohol to four gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below. Turn the Ornamental Ring A clockwise and counterclockwise to detach it. Removal Tweezers A 1 2 3 4 Remove the screw and remove the Zoom Motor Gear Block from the Main body. Remove the FG Plate Spring while disengaging the two Claws. Pull the two Sensors out of the Zoom Motor Gear Block. Remove solder at two locations to detach the Zoom Motor Gear Block from the Main Flexible Board. Ornamental Ring A Solvent A Zoom Motor Gear Block Screw Claws Zoom Motor Gear Block FG Plate Spring Main Flexible Board Solders Disengage the four claws and remove the Barrier Assy. Barrier Assy Sensors Claws Claws Zoom Motor Gear Block Installation 1 Solder the Main Flexible Board at two locations and insert the two Sensors into the Zoom Motor Gear Block. 2 Install the FG Plate Spring while engaging the two Claws. Installation Fit the four claws while inserting the Barrier Lever into the hole and attach the Barrier Assy. Note: The Barrier Tapes must not be wrinkled. Zoom Motor Gear Block Solders Barrier Assy Barrier Assy Claws Main Flexible Board Claws Mark FG Plate Spring Barrier Assy Mark Barrier Levers Sensors holes Claws Zoom Motor Gear Block 3 Install the Zoom Motor Gear Block to the Main body and tighten the screw. Peel off the release papers of the Barrier Tapes. Install the Ornamental Ring A and press it lightly. Barrier Tapes Screw Ornamental Ring A Zoom Motor Gear Block Barrier Tapes DSC-HX20/HX20V/HX30/HX30V_L2 1-12 Zoom Motor Gear Block Ver. 1.1 2012.05 The changed portions from Ver. 1.0 are shown in blue. 1-11. CAM TUBE (B) ASSY REPLACING METHOD 6 Turn the Naruto Gear jig clockwise to set the Main body at TELE end. Note: Turn the Naruto Gear jig to the maximum. 7 Disengage the four Convexes on the Flexible Boards from the four Claws and pull the Flexible Boards out of the holes. Creation of Naruto Gear jig Prepare a Naruto Gear (4-424-720-01) and a fine-tipped screwdriver (or thin stick such as bamboo skewer). Insert a fine-tipped screwdriver (or thin stick such as bamboo skewer) into the Naruto Gear hole and fix the Naruto Gear and the screwdriver with bond or equivalent. Outside Fine-tipped screwdriver. (or thin stick such as bamboo skewer) Naruto Gear (4-424-720-01) Flexible Boards Naruto Gear jig Fix with bond or equivalent. Claw Hole Claws Claw Holes Removal 1 Peel off the Adhesive Tape. Note: Removed Adhesive Tape must not be reused. Use new Adhesive Tape. 2 Disconnect the Flexible Board from the Connector. 3 Remove solder at four locations to detach the three Bosses and the Convex on the Flexible Board. Boss Boss Solders Boss 8 Turn the Naruto Gear jig counterclockwise to set the Main body to the retracted state. Note: Turn the Naruto Gear jig to the maximum. 9 Further turn the Gear clockwise (approx. 5 degrees) and remove the Stationary Tube from the Main body. Convex Flexible Board Main body Adhesive Tape Naruto Gear jig 4 Remove the six screws and remove the Rear Mirror Plate Assy and the Zoom Motor Gear Block. 5 Pull out the Naruto Gear. Screws Screws Rear Mirror Plate Assy Naruto Gear Gear Zoom Motor Gear Block Stationary Tube DSC-HX20/HX20V/HX30/HX30V_L2 1-13 q; While holding the Feed-Through Cam Tube, turn the Rotary Tube Assy clockwise (approx. 5 degrees) and remove the Lens Block from the Feed-Through Cam Tube. qs While holding the Cam Tube (B) Assy, fully turn the Straight Tube (A) Assy clockwise (approx. 120 degrees) and remove the 2nd-4th Lens Block from the 1st Lens Block. 2nd-4th Lens Block Cam Tube (B) Assy Lens Block Feed-Through Cam Tube Feed-Through Cam Tube Straight Tube (A) Assy 1st Lens Block Rotary Tube Assy qa Turn the Feed-Through Cam Tube and set the Projection (large) on the Feed-Through Cam Tube and the Gear of the Rotary Tube Assy at the positions shown in the figure, and then remove the Feed-Through Cam Tube from the Rotary Tube Assy. qd Remove the Ornamental Ring (A), Barrier Assy, and 1st Lens Assy from the Straight Tube (A) Assy. Note: For how to remove the Ornamental Ring (A), Barrier Assy, and 1st Lens Assy, refer to "1-8. Ornamental Ring A or Barrier Assy Replacing Method." Feed-Through Cam Tube Feed-Through Cam Tube Straight Tube (A) Assy Note: For how to remove the Ornamental Ring (A), Barrier Assy, and 1st Lens Assy, refer to "1-8. Ornamental Ring A or Barrier Assy Replacing Method." Ornamental Ring (A) Gear Projection (large) Eyepiece side Eyepiece side Feed-Through Cam Tube Barrier Assy Projection (large) Gear Rotary Tube Assy 1st Lens Assy Gear Projection (large) DSC-HX20/HX20V/HX30/HX30V_L2 Gear 1-14 qf While holding the Straight Tube (B), fully turn the Cam Tube (A) and the Cam Tube (B) Assy counterclockwise (approx. 125 degrees) to extend the Straight Tube (B). qg Remove the 4th Lens Assy. 4th Lens Assy ql While holding the Straight Tube (B), fully turn the Cam Tube (B) Assy counterclockwise (approx. 3 degrees) and remove the 3rd Lens Assy from the eyepiece side. 3rd Lens Assy Cam Tube (B) Assy Straight Tube (B) Straight Tube (B) Straight Tube (B) Cam Tube (A), Cam Tube (B) Assy w; Turn the Cam Tube (B) Assy to align the Cam Tube (B) Assy hole with the cutout of the Straight Tube (B) as shown in the figure. wa Detach the Cam Tube (B) Assy from the Straight Tube (B). qh While holding the Straight Tube (B), turn the Cam Tube (A) and the Cam Tube (B) Assy clockwise (approx. 125 degrees) to set them to the retracted state. 2nd Lens Assy qj Remove the 2nd Lens Assy from the eyepiece side. Cam Tube (B) Assy Straight Tube (B) Cam Tube (B) Assy Hole Cam Tube (A), Cam Tube (B) Assy Straight Tube (B) qk Remove the Cam Tube (A). Cutout Cam Tube (A) DSC-HX20/HX20V/HX30/HX30V_L2 1-15 Installation 5 Align the Bayonet (wide) with the hole and install the Cam Tube (A). Install the Cam Tube (B) Assy to the Straight Tube (B) with the hole aligned with the cutout. Turn the Cam Tube (B) Assy counterclockwise (approx. 141.5 degrees) from the assembled position to align the Groove (tight) of the Straight Tube (B) with the Groove (3rd Lens Assy Inlet) of the Cam Tube (B) Assy as shown in the figure. Cam Tube (A) Groove (tight) Cam Tube (B) Assy Bayonet (wide) Groove (3rd Lens Assy Inlet) Hole Hole 6 Align the White Part with the Bayonet (wide) and install the 2nd Lens Assy while inserting the three Guide keys into the three Guide grooves. 7 While holding the Straight Tube (B), fully turn the Cam Tube (A) and the Cam Tube (B) Assy counterclockwise (approx. 125 degrees) to set them at TELE end. White part 2nd Lens Assy Straight Tube (B) Cam Tube (B) Assy Cutout Straight Tube (B) Guide key Guide keys Guide grooves Guide groove Align the Flexible Board with the Step as shown in the figure and install the 3rd Lens Assy while inserting the three Projections of the 3rd Lens Assy into the three Grooves (tight) of the Straight Tube (B). While holding the Straight Tube (B), turn the Cam Tube (B) Assy clockwise (approx. 3 degrees) to retain the 3rd Lens Assy position. Cam Tube (A), Cam Tube (B) Assy Projections 3rd Lens Assy Bayonet (wide) Cam Tube (B) Assy 8 Align the Flexible Board with the Flexible Board and install the 4th Lens Assy while inserting the three Guide keys into the three Guide grooves. 9 While holding the Straight Tube (B), fully turn the Cam Tube (A) and the Cam Tube (B) Assy clockwise (approx. 125 degrees) to set them to the retracted state. Flexible Board Flexible Board Step Guide key Straight Tube (B) Flexible Board 4th Lens Assy Straight Tube (B) Guide keys Guide groove Grooves (tight) Guide grooves Cam Tube (A), Cam Tube (B) Assy DSC-HX20/HX20V/HX30/HX30V_L2 1-16 q; Align the White Part with the Groove (wide) as shown in the figure and install the 1st Lens Assy to the Straight Tube (A) Assy while inserting the three Guide keys into the three Guide grooves. qd Align the Projection (large) with the Gear as shown in the figure and install the Feed-Through Cam Tube to the Rotary Tube Assy. qf Turn the Feed-Through Cam Tube in the arrow direction to set the Projection (large) and the Gear to the positions shown in the figure. Projection (large) Guide keys Feed-Through Cam Tube Feed-Through Cam Tube White Part 1st Lens Assy Groove (wide) Guide groove Straight Tube (A) Assy Eyepiece side Projection Feed-Through (large) Cam Tube Guide grooves Gear qa qs Eyepiece side Rotary Tube Assy Align the Bayonet (wide) with the Groove (wide) and install the 2nd-4th Lens Block to the Straight Tube (A) Assy. While holding the Cam Tube (B) Assy, fully turn the Straight Tube (A) Assy clockwise (approx. 120 degrees) to set it to the retracted state. Gear Gear Projection (large) Bayonet (wide) 2nd-4th Lens Block qg Align the semicircular edge with the Naruto Gear mounting hole as shown in the figure and install the Feed-Through Cam Tube and the Rotary Tube Assy to the Stationary Tube. qh Engage the seven Projections of the Feed-Through Cam Tube with the seven Grooves of the Stationary Tube. Cam Tube (B) Assy Groove (wide) Feed-Through Cam Tube Projection Semicircular edge (large) Straight Tube (A) Assy Feed-Through Cam Tube, Rotary Tube Assy Straight Tube (A) Assy Stationary Tube Stationary Tube DSC-HX20/HX20V/HX30/HX30V_L2 1-17 Naruto Gear mounting hole qj Align the Step with the Focus Lens Sliding Groove and install the Lens Block to the Feed-Through Cam Tube. qk Engage the Projections of the Cam Tube (B) Assy and the Straight Tube (B) with the eleven Grooves of the Feed-Through Cam Tube. ql Turn the Naruto Gear jig clockwise to set the Main body at TELE end. Note: Turn the Naruto Gear jig to the maximum. Lens Block ws Install the Rear Mirror Plate Assy and the Zoom Motor Gear Block and secure them with six screws. Note: Tighten the screws in the order of numbers in the figure below. wd Install the Ornamental Ring (A) and the Barrier Assy. Note: For how to install the Ornamental Ring (A) and the Barrier Assy, refer to "1-8. Ornamental Ring A or Barrier Assy Replacing Method." Screws Naruto Gear jig 6 4 Screws Ornamental Ring (A) 3 Feed-Through Cam Tube 5 1 2 Rear Mirror Plate Assy Barrier Assy Step Feed-Through Cam Tube Zoom Motor Gear Block Cam Tube (B) Assy, Straight Tube (B) Focus Lens Sliding Groove w; Pass the Flexible Boards through the holes and engage the four Convexes on the Flexible Boards with the four Claws. wa Install the Naruto Gear. Note: Set the Naruto Gear with its deeper hole facing down. wf wg wh wj Outside Connect one Flexible Board to the Connector. Fix the three Bosses and a Convex on the Flexible Board, and then solder the Flexible Board at four locations. Stick Adhesive Tape. Apply a voltage of 2.5 V to the DC Motor and retract the Lens. Boss Naruto Gear Flexible Boards Claw Claws Claw Boss Solders Boss Up side Convex Holes Down side Flexible Board Adhesive Tape DC2.5V DSC-HX20/HX20V/HX30/HX30V_L2 1-18 Ver. 1.1 2012.05 The changed portions from Ver. 1.0 are shown in blue. 1-12. FINAL INSPECTION 1-12-2. Inspection When Cam Tube Block Assy Or Straight Tube Lubricated Assy Is Replaced Focus check 1 Preparation • Camera installed re-assemble lens. • Chart (Printed PDF file at the same magnification) (Refer to <Reference>) • Tripod • Mirror (ex. CD) • Memory card • PC 2 Shoot setting (1) Paste the chart. • Chart should be on the flat wall. • Illuminance level in the chart should be the same. • Make the tripod’s height and the center of the chart to the same height. • Enough space needed for shooting. (2) Set the camera. • Set [P] mode • Set [Maximum] size • Set ISO lowest level • Set Steady Shot [OFF] • Set Flash [OFF] (3) Set the camera on a tripod. (4) Adjust the position of the camera and the chart. 1. Set the zoom position of the camera at Wide end. 2. Attach the mirror onto the center of the chart. * The mirror should not tilt on the chart. 3. Set the camera to display the chart on LCD like in the following picture. 4. Adjust the camera position to the center of the chart. * Adjust the tripod height and the position (Lateral direction). 5. Adjust the camera angle to the frame of the chart with tripod. Remove the mirror. 3 Shooting (1) Set [Self-Timer] (2) Shot 4 Check the shot image. (1) Check the shot image on PC. 100% Display (Display at the same magnification of its Pixel.) Compare the image with the sample you set. No extreme focus blurring It should be distinguished the black and white by the sharpness between them. If it is in NG level, replace the lens unit. 1-12-1. Confirm There is No Fault in Actual Motion/Actual Screen Inspect it as follows when you exchange parts in the lens block. 1 Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º) No abnormal sound or motion must be found over full stroke between TELE end and WIDE end. 2 Zoom image No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between TELE end and WIDE end. 3 Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º) The barrier must be opened and closed fully, free from a sticking in the midway. No abnormal sound must be heard during the operation. 4 Appearance condition Scratches or stains must not be noticeable, except that the customer permits them. 5 Foreign matters on the lens The lens condition must not be worse than that when the camera was received from the customer. Upward Lens at WIDE end Full stroke check Horizontal Lens at TELE end Downward <Reference> • How to Print the Chart Print “Forcus-Chart_A3.pdf” with printer. Print at the same magnification (It means 100 % size). Check the settings of printer to print in proper size. • Check of chart size. Make charts together and check if the size of charts is the following size. * The chart consists of 2 pcs. DSC-HX20/HX20V/HX30/HX30V_L2 1-19E 2. REPAIR PARTS LIST IDENTIFYING PARTS (ENGLISH) NOTE: • -XX, -X mean standardized parts, so they may have some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • CAPACITORS: uF: μF • COILS uH: μH • RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable • SEMICONDUCTORS In each case, u: μ, for example: uA...: μA... , uPA... , μPA... , uPB... , μPB... , μPC... , μPC... , uPD..., μPD... Follow the disassembly in the numerical order given. SW-589 Board Cabinet (Rear) Ashy Cabinet (Top) Block • RL-129 Board • RL-130 Flexible Board SY-325 Board R Cabinet (BTH) Block • BT-077 Flexible Board The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries according to the instructions. • (JAPANESE) 【使用上の注意】 • ここに記載されている部品は, 補修用部品であるため, 回路図及び セットに付いている部品と異なる場合があります。 • -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合 があります。 • *印の部品は常備在庫しておりません。 • コンデンサの単位でuFはμFを示します。 • 抵抗の単位Ωは省略してあります。 金 被:金属被膜抵抗。 サンキン:酸化金属被膜抵抗。 • インダクタの単位でuHはμHを示します。 • 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ A..., μPA..., μPB..., μPC..., μPD...を示します。 LCD RB Strobe Block Color Indication of Appearance Parts Example: (SILVER) : Cabinet’s Color (Silver) : Parts Color 0印の部品,または0印付の点線で囲ま れた部品は,安全性を維持するために, 重要な部品です。 従って交換時は,必ず指定の部品を使用 してください。 • 外装部品色表示 例: (SILVER) :セットの色を表す。 (Silver) :部品の色を表す。 Main Frame • Abbreviation AUS : Australian model CH : Chinese model CND : Canadian model HK : Hong Kong model J : Japanese model KR : Korea model TW : Taiwan model Lens Block • CD-840 Flexible Board View Position Top View Left View Back View Cabinet (Bottom) RT (Front) Ashy Cabinet (Side) Right View Front View Bottom View Link DISCHARGING OF THE CHARGING CAPACITOR DSC-HX20/HX20V/HX30/HX30V_L2 ACCESSORIES ASSEMBLY 2-1 – ENGLISH – NOTE FOR REPAIR • Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. – JAPANESE – 修理時の注意 Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside) • フラットケーブルおよびフレキシブル基板の端子面に欠け, 折れ等がないことを確認する。 また,コネクタへの接続は,差し込み不足や斜め差しになら ないように注意する。 • When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped. • コネクタを取り外す時に,線材部(極細)を持って引っ張ると 断線する恐れがありますので,絶対に線材部(極細)を持って 引っ張らないでください。 • When installing a connector, don’t press down at wire of connector. It is possible that a wire is snapped. • Do not apply excessive load to the gilded flexible board. • 線材部(極細)を押さえながらコネクタを差し込むと,線材部 (極細)が断線する恐れがありますので,絶対に線材部(極細) には負担をかけないでください。 DISCHARGING OF THE CHARGING CAPACITOR (C901/C902) • 金メッキされているフレキシブル基板には,強い負担をかけ ないでください。 The charging capacitor is charged up to the maximum 315 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be discharged as described below. Preparing the Short Jig వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ 㒰ߒߡߊߛߐޕ 㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ ႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕 ストロボ用充電コンデンサ (C901/C902) の放電 Note: High-voltage cautions Discharging the Capacitor Short-circuit between two points with the short jig about 10 seconds. ストロボ用充電コンデンサは最大315 Vの電圧で充電さ れています。 この高電圧で充電されたコンデンサに手を触れた場合, 電気ショックを受けます。この高電圧には単にセットの 電源を切っただけでは放電されず,残留しています。こ のため,下記の方法で残留電圧を放電してください。 R: 1 k Ω/1 W (Part code: 1-215-869-11) To preparing the short jig, a small clip is attached to each end of a resistor of 1 kΩ /1 W (1-215-869-11). Wrap insulating tape fully around the leads of the resistor to prevent electrical shock. Unless the screws shown below are installed, the capacitor cannot be discharged. Discharge the capacitor with these screws installed. 1 kΩ/1 W ショート治具の準備 ショート治具は1kΩ/1W抵抗 (1-215-869-11) 小型のクリップを接続して作成します。 抵抗器は絶縁テープで完全に覆い電気ショックを受けな いようにしてください。 ࠦࡦ࠺ࡦࠨߩ㔚 ࡈ࠶ࠪࡘ࡙࠾࠶࠻ߩ㔚Ḯࠦࡦ࠺ࡦࠨ ߩ┵ሶ㑆ࠍ࡚ࠪ࠻ᴦౕߢ⚂⑽㑆 ធ⛯ߔࠆޕ R:1 k Ω/1 W ㇱຠࠦ࠼㧦1-215-869-11 ਅ࿑ߩߨߓ߇ขࠅઃߌࠄࠇߡ ߥߣޔ㔚᧪߹ߖࠎޕ ߨߓ߇ขࠅઃߌࠄߡࠆ⁁ᘒ ߢ㔚ࠍⴕߥߞߡߊߛߐޕ 1 kΩ/1 W Wrap insulating tape. ⛘✼࠹ࡊߢᏎߊ RL-129 Flexible Board RL-129 Flexible Board Plate (GPS) Plate (GPS) C901 C901 C902 DSC-HX20/HX20V/HX30/HX30V_L2 C902 2-2 Ver. 1.2 2012.06 The changed portions from Ver. 1.1 are shown in blue. 2-1. EXPLODED VIEWS DISASSEMBLY 2-1-1. REAR SECTION 1. Remove to numerical order (1 to 6) in the left figure. 1 #243 X 1 2 Open the HDMI lid (2) → #243 X 6 Bottom View Bottom View Left View 2 Claws #243 29 (Note 1, 3) #243 8 7 3 (Note 4) Screw (Note 4) #243: M1.4 X 3.5 (Black) 4-412-769-01 5 Bosses #243 #243 #243 56 Right View Claws Claws 3 2 1.4 2 3.5 6 LCD901 Note Be sure not to fold these sheets. 4 Note 1: When replacing this part, be careful whether a LOGO is existed or not. 交換時にロゴの有無に注意してください。 Note 2: When replacing this part, be careful whether a LOGO is existed or not. 交換時にロゴの有無に注意してください。 GPS logo GPSのロゴ 41 Wi-Fi logo Wi-Fiのロゴ TransferJet logo TransferJetのロゴ Main Section (See page 2-4) Claws Claws #243 HX30V (Jet model) A-1878-228-A SERVICE, CABINET (REAR) (J) (BLACK) A-1878-229-A SERVICE, CABINET (REAR) (US) (BLACK) A-1878-233-A SERVICE, CABINET (REAR) (J) (BROWN) HX30 (Jet model) A-1878-236-A SERVICE, CABINET (REAR) (CH) (BLACK) A-1878-237-A SERVICE, CABINET (REAR) (CH) (BROWN) #243 1 10 4-420-614-01 CABINET (SIDE) (350) (HX30V) (BLACK) 4-420-614-11 CABINET (SIDE) (350) (HX30V) (BROWN) Wi-Fi logo Wi-Fiのロゴ HX20V (Jet model) A-1878-241-A SERVICE, CABINET (REAR) (US, UK) (BLACK) A-1878-245-A SERVICE, CABINET (REAR) (UK) (BROWN) (Note 2) 4-420-614-21 CABINET (SIDE) (350) (HX30) (BLACK) 4-420-614-31 CABINET (SIDE) (350) (HX30) (BROWN) GPS logo GPSのロゴ #243 HX30V (Non Jet model) A-1878-230-A SERVICE, CABINET (REAR) (CND) (BLACK) A-1878-231-A SERVICE, CABINET (REAR) (KR) (BLACK) A-1878-234-A SERVICE, CABINET (REAR) (KR) (BROWN) X-2582-937-1 CABINET(REAR) ASSY(350) (BLACK) (HK, TW) (BLACK)) X-2582-938-1 CABINET(REAR) ASSY(350) (BROWN) (HK, TW) (BROWN) Ref. No. Ref. No. Part No. Description 4-420-619-11 4-420-618-01 4-420-618-11 (Note 1) (Note 2) BUTTON (CENTER) (350) (BROWN) (Note 4) BUTTON (KURUPON) (350) (BLACK) (Note 4) BUTTON (KURUPON) (350) (BROWN) (Note 4) SERVICE, CABINET (REAR) (Note 3) CABINET (SIDE) (350) Part No. Description 1 1 2 2 3 4-420-617-01 4-420-617-11 4-420-616-01 4-420-616-11 4-420-629-01 COVER (350), DC (BLACK) COVER (350), DC (BROWN) LID (350), HDMI (BLACK) LID (350), HDMI (BROWN) LCD RETAINER (350) 7 8 8 9 10 4 5 6 6 7 4-424-153-01 4-420-547-01 A-1870-787-A A-1870-788-A 4-420-619-01 SHEET (LB) (350) SHEET (SW) (350) SW-589 BOARD, COMPLETE (HX30/HX30V) SW-589 BOARD, COMPLETE (HX20/HX20V) BUTTON (CENTER) (350) (BLACK) (Note 4) LCD901 A-1872-487-A LCD BLOCK (350) SERVICE #243 SCREW (M1.4), NEW TRU-STAR, P2 DSC-HX20/HX20V/HX30/HX30V_L2 4-412-769-01 HX20V (Non Jet model) X-2583-980-1 CABINET (REAR) ASSY (310) (BLACK) (AEP, E, AUS) (BLACK) X-2583-981-1 CABINET (REAR) ASSY (310) (BROWN) (AEP, E,) (BROWN) 4-420-614-41 CABINET (SIDE) (350) (HX20V) (BLACK) 4-420-614-51 CABINET (SIDE) (350) (HX20V) (BROWN) 4-420-614-61 CABINET (SIDE) (350) (HX20) (BLACK) HX20 (Non Jet model) X-2583-978-1 CABINET (REAR) ASSY (241) (BLACK) 2-3 Note 3: Refer to “Assembly-1 : Installation Cautions of the Rear Cover Assy.”. Note 4: Refer to “Assembly-2 :Installation Cautions of the Button (Center), Button (Kurupon).”. Note 3: “Assembly-1 : Installation Cautions of the Rear Cover Assy.” を参照してください。 Note 4: “Assembly-2 : Installation Cautions of the Button (Center), Button (Kurupon).” を参照してください。 Ver. 1.1 2012.05 The changed portions from Ver. 1.0 are shown in blue. 2-1-2. MAIN SECTION DISASSEMBLY 1. Remove to numerical order (1 to 5) in the left figure. 1 #243 X 3 Bottom View Top View Back View #243 #243 #243 58 #243 58 4 4 Disconnect flexible board (4) Back View Front Section (See page 2-5) 53 4 56 5 #243 55 1 57 (Note 2) 54 5 DISCHARGING OF THE CHARGING CAPACITOR 4 Lens Block Section (See page 2-7) Screw #243: M1.4 X 3.5 (Black) 4-412-769-01 53 1.4 2 52 3.5 3(Claws) Note #243 3 51 Note 1: Refer to page 1-5 “Precaution on replacing the Cabinet (Bottom)” when changing the Cabinet (Bottom). (Note 1) Note 1: キャビネットボトム組立の交換時は、1-11ページの “キャビネット(底)交換時の注意” を参照してください。 Note 2: When this part is removed, adjustment is required. For the adjustment method, refer to “Adjustment items after replacing parts” in the Note tab of the Adjust manual. Ref. No. 51 52 53 54 55 Part No. Description (Note 1) 4-420-633-01 4-424-153-01 4-420-639-01 4-420-640-01 BOTTOM (350), CABINET GASKET (USB) (350) SHEET (LB) (350) CUSHION (LENS-S) (350) SHEET (CD) (350), RADIATION DSC-HX20/HX20V/HX30/HX30V_L2 Ref. No. Part No. Description 56 57 58 4-420-638-01 4-420-626-01 4-420-630-01 CUSHION (LENS-T) (350) FRAME (MAIN) (350) (Note 2) CUSHION (LCD-S) (350) #243 4-412-769-01 SCREW (M1.4), NEW TRU-STAR, P2 Note 2: この部品を取り外したときは調整が必要です。 調整方法については Adjust manual の Noteタブにあ るAdjustment items after replacing parts を参照して ください。 2-4 ストロボ用充電コンデンサの放電 Ver. 1.1 2012.05 The changed portions from Ver. 1.0 are shown in blue. DISASSEMBLY 2-1-3. FRONT SECTION 1. Remove to numerical order (1 to 5) in the left figure. 2. The meaning of the sign in left figure is as follows. Be careful when it removes. ◇: Solder 1 #78 X 1 2 #28 X 2 Back View Back View 107 1 106 2 Top/BTH Section (See page 2-6) #78 SY -32 5 5 103 (Note 1) Claws #28 Screw #78 #78: M1.4 X 3.5 (Red) 3-208-537-11 #28: M1.4 X 4.0 (Tapping) (Silver) 3-348-998-61 1(Claws) #28 4.0 2(Claws) 102 Note Note 1: Refer to “Assembly-4 : Precaution During of ST block installation.”. 3 105 Note 1: “ A s s e m b l y -4 : P r e c a u t i o n D u r i n g o f S T b l o c k installation.” を参照してください。 4(Claws) Note 2: When this part is removed, adjustment is required. For the adjustment method, refer to “Adjustment items after replacing parts” in the Note tab of the Adjust manual. 5(Claws) SP901 Note 2: この部品を取り外したときは調整が必要です。 調整方法については Adjust manual の Noteタブにあ るAdjustment items after replacing parts を参照して ください。 101 (Note 2) Part No. Description 101 101 102 103 103 X-2582-931-1 X-2582-932-1 X-2584-079-1 A-1872-783-A A-1872-784-A (FRONT) ASSY (350) (BLACK) (BLACK) (Note 2) (FRONT) ASSY (350) (BROWN) (BROWN) (Note 2) GEAR ASSY (350), ST ST BLOCK (350) BLACK SERVICE (BLACK) (Note 1) ST BLOCK (350) BROWN SERVICE (BROWN) (Note 1) 104 105 4-420-627-01 4-420-625-01 PLATE (SP) (350) SCREW, TRIPOD (350) DSC-HX20/HX20V/HX30/HX30V_L2 3.5 4 104 Ref. No. 1.4 1.4 Ref. No. Part No. Description 106 107 A-1872-666-A 1-885-489-11 SY-325 BOARD, COMPLETE (SERVICE) SW-592 FLEXIBLE BOARD SP901 1-858-343-51 LOUDSPEAKER (1.0CM) #28 #78 3-348-998-61 3-208-537-11 SCREW (M1.4X4), TAPPING, PAN 0+Z M1.4X2 NEW TORASUTA 2-5 Ver. 1.2 2012.06 The changed portions from Ver. 1.1 are shown in blue. DISASSEMBLY 2-1-4. TOP/BTH SECTION 1. The meaning of the sign in left figure is as follows. Be careful when it removes. ◇-X: Solder Screw #28: M1.4 X 4.0 (Tapping) (Silver) 3-348-998-61 156 (Note 2) 1.4 4.0 Claws 155 MIC901 Claws Note 161 (Note 1) 157 162 158 154 Note 1: Refer to “Assembly-3 : Installation Cautions of the RL129 Board.”. (Note 2) Note 1: “Assembly-3 : Installation Cautions of the RL-129 Board.” を参照してください。 Claws BT001 Note 2: When this part is removed, adjustment is required. For the adjustment method, refer to “Adjustment items after replacing parts” in the Note tab of the Adjust manual. 159 (Note 2) BT901 Note 2: この部品を取り外したときは調整が必要です。 調整方法については Adjust manual の Noteタブにあ るAdjustment items after replacing parts を参照して ください。 160 C901 #28 C902 153 152 : BT001 (LITHIUM RECHARGEABLE BATTERY) Board on the mount position. (See page 6-24 of Level 3) 151 Ref. No. Part No. Description 151 151 152 153 154 X-2582-933-1 X-2582-934-1 4-420-624-01 4-420-623-01 A-1870-789-A BTH ASSY (350) (BLACK) (BLACK) BTH ASSY (350) (BROWN) (BROWN) COVER (JET) (350) PLATE (JET) (350) BT-077 FLEXIBLE BOARD, COMPLETE 155 156 156 157 158 4-420-628-01 X-2582-935-1 X-2582-936-1 4-420-622-01 4-420-621-01 RETAINER (350), RL (UPPER) ASSY (350) (BLACK) (BLACK) (Note 2) (UPPER) ASSY (350) (BROWN) (BROWN) (Note 2) CUSHION (MIC LOWER) (350) RETAINER (350), MICROPHONE DSC-HX20/HX20V/HX30/HX30V_L2 Ref. No. Part No. Description 159 A-1873-028-A 159 A-1870-786-A 160 161 162 4-420-620-01 4-416-599-01 1-885-400-11 RL-129 BOARD, COMPLETE (SERVICE) (HX20V/HX30V) (Note 2) RL-129 BOARD, COMPLETE (SERVICE) (HX20/HX30) (Note 2) PLATE (GPS) (350) PLATE (330), ROTARY (Note 1) RL-130 FLEXIBLE BOARD (Note 2) BT001 *BT901 C901 C902 MIC901 1-756-710-12 1-780-826-11 1-118-124-11 1-118-124-11 1-542-862-61 LITHIUM RECHARGEABLE BATTERY TERMINAL BOARD, BATTERY CAP, ALUMINIUM ELECT 67uF 315V CAP, ALUMINIUM ELECT 67uF 315V MICROPHONE UNIT #28 3-348-998-61 SCREW (M1.4X4), TAPPING, PAN 2-6 Ver. 1.1 2012.05 The changed portions from Ver. 1.0 are shown in blue. DISASSEMBLY 2-1-5. LENS BLOCK SECTION 1. The meaning of the sign in left figure is as follows. Be careful when it removes. ◇-X: Solder ns: not supplied Screw #258: M1.4 X 3.5 (Tapping) (Silver) 4-299-468-11 #189: M1.4 X 3.5 (Tapping) (Silver) 3-686-458-21 212 204 201 1.4 (including CD-840 flexible complete board, CP001 (CMOS imager)) (Note 3) (Note 1, 2, 5) ns 1.2 3.5 3.5 ns 203 ns Note 202 207 Note 1: #258 206 PRECAUTIONS WHEN HOLDING THE LENS BLOCK Hold the Lens Block at the center of both sides. #189 205 Do not hold the following part. Focus Motor Very weak Hold here. Zoom Motor Very weak ns Flexible Board Sensor Very week 211 209 #189 208 Ornamental Ring ns ns 210 ns 213 Note 2: レンズブロックの各部品を交換する際は,下記の各項目を参照してください。 • 1-9. ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD (page 1-12) • 1-10. ZOOM MOTOR GEAR BLOCK REPLACING METHOD (page 1-12) • 1-11. CAM TUBE (B) ASSY REPLACING METHOD (page 1-13) • 1-12. FINAL INSPECTION (page 1-19) Note 3: Be sure to read “Precautions for Replacement of Imager” on page 6-1 of Level 3 when changing the imager. Part No. Description 201 202 203 204 205 1-856-265-11 4-424-721-01 X-2584-294-1 X-2584-295-1 4-424-723-01 OPTICAL UNIT (BE017) (Note 1, 2, 5) RING (A), ORNAMENTAL BARRIER ASSY TUBE (A) ASSY, STRAIGHT TUBE (A), CAM 206 207 208 X-2584-297-1 4-424-724-01 X-2584-296-1 TUBE (B) ASSY, CAM TUBE (B), STRAIGHT TUBE ASSY, ROTARY DSC-HX20/HX20V/HX30/HX30V_L2 Ref. No. Part No. Description 209 210 4-424-722-01 4-424-720-01 TUBE, FEED-THROUGH CAM GEAR, NARUTO 211 212 1-490-422-11 A-1870-790-A 213 2-580-751-01 GEAR BLOCK, ZOOM MOTOR (BE017) CD-840 FLEXIBLE BOARD, COMPLETE (including CP001 (CMOS imager)) (Note 3) SHEET, POLYIMIDE (Note 4) #189 #258 3-686-458-21 4-299-468-11 SCREW (P1.4), TAPPING SCREW, TAPPING UB1.2 Focus Lens Very weak Note 2: Refer to the following each item when you exchange parts of Lens Block. • 1-9. ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD (page 1-12) • 1-10. ZOOM MOTOR GEAR BLOCK REPLACING METHOD (page 1-12) • 1-11. CAM TUBE (B) ASSY REPLACING METHOD (page 1-13) • 1-12. FINAL INSPECTION (page 1-19) (Size: 16mm X 40mm) (Note 4) Ref. No. Lens Barrier Very weak Note 3: イメージャの交換時はLevel3の6-1ページ、“イメージャ 交換時の注意” を必ずお読みください。 Note 4: Cut SHEET, POLYIMIDE (2-580-751-01) into the designed length and use it. Note 4: SHEET、POLYIMIDE(2-580-751-01)は切って使用し てください。 2-7 Note 5: When this part is removed, adjustment is required. For the adjustment method, refer to “Adjustment items after replacing parts” in the Note tab of the Adjust manual. Note 5: この部品を取り外したときは調整が必要です。 調整方法については Adjust manual の Noteタブにあ るAdjustment items after replacing parts を参照して ください。 Ver. 1.1 2012.05 The changed portions from Ver. 1.0 are shown in blue. ACCESSORIES 901 902 905 906 903 904 Ref. No. Part No. Description Ref. No. Part No. Description 901 901 901 901 902 1-489-282-11 1-489-282-21 1-489-282-31 1-489-282-61 1-837-421-11 AC Adaptor AC-UB10/UB12B (J) AC Adaptor AC-UB10/UB10B (US, CND) AC Adaptor AC-UB10/UB10B (CH) AC Adaptor AC-UB10/UB17B (EXCEPT US, CND, CH, J) Power cord (mains lead) (UK, E (Saudi), HK) * 906 * 906 * 906 906 4-419-606-71 4-419-606-81 4-419-606-91 4-419-607-11 906 4-419-607-21 Instruction Manual (ENGLISH, SPANISH, PORTUGUESE) Instruction Manual (ENGLISH, ARABIC, PERSIAN) Instruction Manual (ENGLISH, TRADITIONAL CHINESE) Instruction Manual (ENGLISH, TRADITIONAL CHINESE, SIMPLIFIED CHINESE) Instruction Manual (KOREAN) 902 902 902 902 903 1-837-424-11 1-837-427-11 1-837-428-11 1-837-429-11 1-569-008-12 Power cord (mains lead) (TW) Power cord (mains lead) (AEP, E (EXCEPT Saudi)) Power cord (mains lead) (KR) Power cord (mains lead) (AUS) Conversion (2P) Adaptor (E: NTSC) 904 905 906 * 906 906 1-839-666-11 2-050-981-11 4-419-605-01 4-419-605-11 4-419-606-11 Micro USB cable Wrist strap Instruction Manual (JAPANESE) Instruction Manual (SIMPLIFIED CHINESE) Instruction Manual (ENGLISH) 906 906 906 906 4-419-606-21 4-419-606-31 4-419-606-41 4-419-606-51 * 906 4-419-606-61 Instruction Manual (ENGLISH, SPANISH) Instruction Manual (ENGLISH, FRENCH) Instruction Manual (ENGLISH, RUSSIAN, UKRAINIAN) Instruction Manual (ENGLISH, FRENCH, ITALIAN, SPANISH, PORTUGUESE, GERMAN, DUTCH, TURKISH, GREEK, POLISH, CZECH, HUNGARIAN, SLOVAK, SWEDISH, FINNISH, NORWEGIAN, DANISH, CROATIAN, ROMANIAN) Instruction Manual (ENGLISH, SIMPLIFIED CHINESE, TRADITIONAL CHINESE, MALAY, INDONESIAN, THAI, ARABIC, PERSIAN) * * * * Note: This unit has no bundled CD-ROM. Contents included in the CD-ROM will be supplied to customers as follows. ・ User Guide (HTML) - You can access to the URL of support site described in the Instruction Manual. - All of the contents in the User Guide are included in the Instruction Manual or built-in guide. ・ Application Software - By connecting this unit and Windows PC with the USB cable, the application software [PlayMemories Home Lite version] can be installed on the PC from the unit. - In case of using the extended version, install “Expanded Feature” via Internet. This item is supplied with the unit as an accessory, but is not prepared as a service part. 951 Ref. No. 951 Part No. (Not supplied) Description Rechargeable battery pack NP-BG1 DSC-HX20/HX20V/HX30/HX30V_L2 2-8E 3. ASSEMBLY Assembly-1: Installation Cautions of the Rear Cover Assy. Be sure to install the Rear Cover Assy with the strobe pulled out. Assembly-3: Installation Cautions of the RL-129 Board. Marking (Adjust the position) RL-129 Board Rotary plate 1 strobe 2 Cabinet (Upper) Assy Rear Cover Assy Adjust the position Assembly-2: Installation Cautions of the Button (Center), Button (Kurupon). Assembly-4: Precaution During of ST block installation. Set the switch of the Flexible board of the strobe unit as shown in the figure. Claws Flexible board of the strobe unit Lever Button (Center) Button (Kurupon) Claws DSC-HX20/HX20V/HX30/HX30V_L2 Set the Lever as shown in the figure. 3-1E NOTE The wireless LAN connection settings have been initialized and the MAC address has also been modified during this repair. Make settings again for connection to devices as needed. For details of settings, refer to the Instruction Manual. 注意 因為修理原因,無線 LAN 的連接設定已初始 化。 此外,MAC 地址也已變更。 請務必要再度為所有通訊裝置進⾏起始設 定。 關於進⾏設定的詳細資訊,請參考 “使⽤說明書”。 참고 이 복구가 수행되는 동안 무선 LAN 연결 설정이 초기화되었고 MAC 주소가 수정되었습니다 . 필요에 따라 장치에 대한 연결을 다시 설정하십시오 . 설정에 대한 자세한 내용은 사용 설명서를 참조하십시오 . ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- 20x optical zoom lens
- 18.2-megapixel Exmor R CMOS sensor
- 3.0-inch LCD screen
- AVCHD recording
- MP4 recording
- Built-in Wi-Fi (DSC-HX30/HX30V only)
- Optical SteadyShot image stabilization
- Scene Selection modes
- Self-Diagnosis function
- Flash Error Repair Tool
Frequently asked questions
The self-diagnosis function helps identify and troubleshoot problems with the camera. When a problem occurs, a 4-digit code is displayed on the LCD screen, indicating the type of error and the appropriate solution.
The Flash Error Repair Tool is used to reset the flash settings after a flash error has occurred. This tool is required to enable flash charging and firing after a flash error has been resolved.
You can copy data from the internal memory to a memory card by accessing the Memory Card Tool menu. This tool allows you to copy all images in the internal memory to a memory card in a single step.
You can format the internal memory or a memory card by accessing the Memory Card Tool or Internal Memory Tool menu. Formatting will permanently erase all data on the selected storage media.