Manual - Webstaurant Store
Countertop and Freestanding Ice and Water
Dispenser with Chewblet® Ice Machine
7CI100A, 7FS100A
Installation, Operation and Service Manual
Serial numbers E01087 and above
7CI100A
7FS100A
Following installation, please forward this manual
to the appropriate operations person.
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Order parts online:
www.follettice.com
00951640R07
Contents
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Ambient Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Refrigeration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Heat Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Detailed Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Countertop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Freestanding Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Maintenance/Cleaning Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Accessing Internal Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Filter Display Indicator Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
LED Indicator Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Evaporator Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Evaporator Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Water Feed Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Bin Melt Water/Evaporator Feed/Clean Out System Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Vent System Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Refrigeration Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Condenser Fan Motor Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
User Interface Display Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Electrical Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Bin Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Evaporator Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Base Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2
Dispenser and Ice machine 7CI100A/7FS100A
e–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability, and outstanding
after-the-sale support. To ensure that this product delivers that same degree of service, we ask that you take a
moment to review this manual before beginning the installation. Should you have any questions or require technical
help at any point, please call our technical service group at (877) 612-5086 or +1 (610) 252-7301.
Before You Begin –––––––––––––––––––––––––––––––––––––––––––––––––––
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage
is found, immediately notify the shipper and contact Follett Corporation so that we can help in the filing of a claim,
if necessary. If needed, the serial number of your dispenser can be found by removing the drip tray ❶ and locating
the serial number label ❷. A QR Code is located on the right hand side of the drip tray ❸. This code allows you to
access manuals, technical bulletins, and on-line training related to the 7 Series dispensers.
Scan to access technical
documentation or visit
www.follettice.com/7seriesdocs
00981100R00
2
1
3
Check your paperwork to verify that you received the correct dispenser. Follett configuration numbers are designed
to provide information about the type of dispenser you are receiving. The following is an explanation of the different
model numbers.
7
Dispenser Storage
Capacity
7 lb
CI
100
Configuration
CI
FS
Countertop
Freestanding
A
Ice Machine Capacity
100
lb per day
Condenser
A
Air-cooled
Important Safety Information –––––––––––––––––––––––––––––––––––––––––
Please read and adhere to the following safety information while installing, using, or servicing your Follett 7 Series
Ice Dispenser.
1.
Always disconnect power before servicing the dispenser.
2. Ice is slippery. Maintain counters and floors around dispenser in a clean and ice-free condition.
3. Ice is food. Follow the recommended cleaning and sanitizing instructions to maintain cleanliness of
delivered ice.
Dispenser and Ice machine 7CI100A/7FS100A
3
Specifications –––––––––––––––––––––––––––––––––––––––––––––––––––––
Dimensions
7CI100A
7FS100A
Width
14.55" (370 mm)
14.55" (370 mm)
Depth
22.05" (560 mm)
22.05" (560 mm)
Height
17.53" (450 mm)
41.93" (1065 mm)
Unit Shipping Weight
90 lb (41 kg)
120 lb (54.4 kg)
Ambient Information
CAUTION!
The 7CI100A and 7FS100A are for indoor use only.
Maximum*
†
Minimum*
Air Temperature
100 F (38 C)
50 F (10 C)
Water Temperature
90 F (32.2 C)
40 F (4.5 C)
Water Pressure
70 psi
Relative Humidity
10 psi
55% at 78 F (25.5 C)
* Use outside of these limitations is misuse and will void warranty.
† Best performance is achieved between 80 F (27 C) and 50 F (10 C).
Plumbing
 Water Inlet: 1/4" MPT
 Optional Drain Accessory Kit (item# 00956375 or 00981977): 1/2" ID tubing
 Water shut-off recommended within 5 ft. (1.5 m) of dispenser
4
Dispenser and Ice machine 7CI100A/7FS100A
Specifications –––––––––––––––––––––––––––––––––––––––––––––––––––––
Water
WARNING!
Connect to potable water supply only.
 Water Mineral Content:
– TDS: greater than 5 ppm (mg/l) but less than 400 ppm (mg/l)
– Hardness: Less than 200 mg/l (12 gpg)
 Not recommended for use with softened water
Clearances
 3" (77 mm) behind and on each side of dispenser for electrical and connection and ventilation
Electrical
 115V, 60 Hz, 1 phase, 5A, maximum fuse 15A
 Connect to dedicated 15A circuit, fuse or breaker
 Must be grounded - requires 3-prong outlet. Do not remove ground.
Refrigeration
WARNING!
Do not damage the refrigerant circuit. Refrigerant can cause personal injury and/or damage dispenser.
 Refrigerant R134a – 7.2 ounces (204 grams)
Heat Rejection
 1700 BTU/hr (498 W)
Dispenser and Ice machine 7CI100A/7FS100A
5
Specifications
(continued)
––––––––––––––––––––––––––––––––––––––––––––––
Detailed Drawing
Countertop models
14.55" (370 mm)
14.55" (370 mm)
NEMA 5-15
right angle
17.54"
(446 mm)
L2
G
17.54"
(446 mm)
L1
6.72"
(171 mm)
6.79"
(172 mm)
power cord
22.05" (560 mm)
2.40"
(61 mm)
1/4" MPT
water inlet
2.98"
(76 mm)
Freestanding models
14.55" (370 mm)
14.55" (370 mm)
NEMA 5-15
right angle
17.54"
(446 mm)
L2
G
17.54"
(446 mm)
L1
6.72"
(171 mm)
6.79"
(172 mm)
power cord
2.40"
(61 mm)
24.39"
(620 mm)
22.05" (560 mm)
6
Dispenser and Ice machine 7CI100A/7FS100A
1/4" MPT
water inlet
2.98"
(76 mm)
Installation ––––––––––––––––––––––––––––––––––––––––––––––––––––––––
CAUTION!
No service or maintenance should be performed until the technician
has thoroughly read this service manual. Except for routine cleaning
and sanitizing, only qualifi ed technicians should attempt to service
or maintain this equipment.
Countertop Installation
Fig. 1
Installation instructions for freestanding model may be found on page 8.
1.
countertop models
A clearance of at least 3" (77 mm) is required behind and on
each side of the dispenser for electrical connection and ventilation
(Fig. 1).
minimum 3" (77 mm)
clearance required
2. Rough-in the electrical service and water line.
 Electrical: 115V, single phase, 15A receptacle required. The dispenser
has an integral 8 ft. (2.4 m) cord and plug.
 Water: supply line (with shut-off valve) connects to the dispenser's 1/4"
MPT inlet.
NOTICE!
If installing optional Drip Tray Drain Kit or Leg Accessory,
complete those steps before proceeding. Refer to instructions
included with the Drip Tray Drain Kit, or see page 8 for Leg
Accessory instructions.
3. Connect water line. Recommended routing (Fig. 2) allows easy access
to water for cleaning and sanitizing procedure.
4. If installing the optional internal water filter*, please see Optional
Internal Water Filter Installation on page 10 before proceeding.
If not, proceed to step 5.
* If your dispenser has the internal water filter option, the water filter must be
installed for the dispenser to operate. Because internal components will need to
be accessed for both procedures, Follett recommends installing the water filter
just prior to initial sanitizing.
Fig. 2
3' (91.4 cm)
Plug
Valve
5. Connect power supply.
6. Sanitize the dispenser prior to use (see Cleaning and Sanitizing
on page 13).
1/4" MPT
Dispenser and Ice machine 7CI100A/7FS100A
7
Installation
(continued)
–––––––––––––––––––––––––––––––––––––––––––––––––
Optional Leg Accessory Installation
Fig. 3
CAUTION!
Use caution when tipping the dispenser during leg installation. Do
not lay unit on back or side. DO NOT EXCEED 30° angle. Tipping
more than 30° can result in compressor malfunction.
1.
If installing optional 4" (10.16 cm) Leg Accessory (item# 00956300),
place a 5" (12.7 cm) spacer underneath the dispenser to ease
installation.
2. Remove four plastic, thread-protecting plugs from bottom of
dispenser.
5" (127 mm)
min.
spacer
3. Screw each leg into chassis (Fig. 3).
Freestanding Installation
Installation instructions for countertop model may be found on Countertop
Installation on page 7.
1.
A clearance of at least 3" (77 mm) is required behind and on
each side of the dispenser for electrical connection and ventilation
(Fig. 4).
2. Rough-in the electrical service and water line.
 Electrical: 115V, single phase, 15A receptacle required. The dispenser
has an integral 8 ft. (2.4 m) cord and plug.
 Water: supply line (with shut-off valve) connects to the dispenser's 1/4"
MPT inlet.
NOTICE!
If installing optional Leg Accessory, complete those steps before
proceeding. See page 10 for Leg Accessory instructions.
8
Dispenser and Ice machine 7CI100A/7FS100A
Fig. 4
freestanding models
minimum 3" (77 mm)
clearance required
Installation
(continued)
–––––––––––––––––––––––––––––––––––––––––––––––––
3. Remove four plastic, thread-protecting plugs from bottom of
dispenser.
Fig. 5
4. Attach dispenser to base stand with supplied hardware (Fig. 5).
NOTICE!
If installing optional Drip Tray Drain Kit, refer to instructions
included with the Drip Tray Drain Kit.
X4
5. Connect water line. Recommended routing (Fig. 6) allows easy access
to water for cleaning and sanitizing procedure.
6. If installing the optional internal water filter*, please see Optional
Internal Water Filter Installation on page 10 before proceeding.
If not, proceed to step 7.
* If your dispenser has the internal water filter option, the water filter must be
installed for the dispenser to operate. Because internal components will need to
be accessed for both procedures, Follett recommends installing the water filter
just prior to initial sanitizing.
7.
Fig. 6
3' (91.4 cm)
Plug
Valve
Connect power supply.
8. Sanitize the dispenser prior to use (see Cleaning and Sanitizing
on page 13).
1/4" MPT
Dispenser and Ice machine 7CI100A/7FS100A
9
Installation
(continued) –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
9. Secure unit to wall or cove molding with supplied bracket (Fig. 7) to
prevent tipping.
Fig. 7
Note: Fasteners must be supplied by installer.
WARNING!
Freestanding unit must be secured to wall to prevent tipping.
Failure to do could result in personal injury or damage to the
unit.
Optional Leg Accessory Installation
1. If installing optional 6" (15.24 cm) Leg Accessory (item# 00956318),
tilt or lay base stand on side and screw each leg into stand (Fig. 8).
Fig. 8
Fig. 9
Optional Internal Water Filter Installation
If your dispenser has the internal water filter option, the water filter must be
installed for the dispenser to operate. Because internal components will need
to be accessed for both procedures, Follett recommends installing the water
filter just prior to initial sanitizing.
1.
If installing the optional internal water filter, please complete the
steps shown in Accessing Internal Components on page 11
before proceeding.
1
2
2. Lift and remove the top panel, set aside (Fig. 9.1).
3. Remove two screws (Fig. 9.2) and remove left side panel.
4. Install filter as shown. Turn filter clockwise until it is fully seated
(Fig. 9.3).
3
10
Dispenser and Ice machine 7CI100A/7FS100A
Maintenance/Cleaning Mode –––––––––––––––––––––––––––––––––––––––––
Fig. 10
Cleaning Mode (Dispensing Disabled) - Use when cleaning surface
Entering Cleaning Mode disables the User Interface and allows you to clean
the outside of the dispenser without accidentally dispensing water or ice.
1.
2
To enter Cleaning Mode, press and immediately release the
maintenance/clean switch (Fig. 10.1) so that only "FRESH
FILTERED ICE AND WATER" displays in the user interface
(Fig. 10.2).
1
2. To exit Cleaning Mode, press and immediately release the
maintenance/clean switch so that the ice and water icons also
display in the user interface.
Maintenance Mode (All Operations Disabled) - Use when cleaning ice
machine
Entering Maintenance Mode disables all operations and allows you to safely
clean and/or sanitize the ice machine and dispenser.
1.
4
To enter Maintenance Mode, press and hold the maintenance/
clean switch (Fig. 10.3) until
displays in the user interface
(Fig. 10.4).
2. To exit Maintenance Mode, press and hold the maintenance/clean
no longer displays in the user interface.
switch until
3
Note: Entering and exiting Maintenance Mode will reset the six-month
periodic maintenance reminder.
Accessing Internal Components ––––––––––––––––––––––––––––––––––––––
Fig. 11
CAUTION!
Except for routine cleaning and sanitizing, only qualifi ed
technicians should attempt to service or maintain this equipment.
1.
Press and hold the maintenance/clean switch (Fig. 10.1) until
displays in the user interface (Fig. 10.2).
2. Remove (unscrew) chrome ice dispenser chute (Fig. 11.1).
1
3. Remove the drip tray (Fig. 11.2).
4. Remove the two screws (Fig. 11.3) on the front panel (behind the
drip tray).
5. Remove and set aside the front panel (Fig. 11.4) - do not
disengage the plug on the back of the User Interface or the
tubing at the water dispenser chute (if so equipped).
3
2
4
Dispenser and Ice machine 7CI100A/7FS100A
11
Filter Display Indicator Activation –––––––––––––––––––––––––––––––––––––
If you purchased your dispenser with a Follett filter, the filter display indicator Fig. 12
activation has been preset at the factory.
If you are using an “after market filter,” an adjustment may be made to
activate the “Fresh Filtered Ice & Water” display.
1
Activating “Fresh Filtered Ice & Water”
1. Remove the front panel as explained in Accessing Internal
Components on page 11 then refer to Fig. 12.
2. Remove top panel (Fig. 12.1).
3. Remove (1) screw and top of control board enclosure (Fig. 12.2).
4. Locate the DIP switches on the dispenser's control board (Fig. 13).
Use a fine-pointed object to move the “Filter” DIP switch (DIP switch
#3) to the ON position.
Deactivating the Six-Month Maintenance/Filter Change Reminder
1. Use a fine-pointed object to move the “PM” DIP switch (DIP switch
#8) to the ON position.
2
OFF
1
Not used (OFF position)
2
Not used (OFF position)
15 minute delay
Not used (OFF position)
Six-month PM enabled
5
3
Ice only
No internal filter
Not used (OFF position)
Ice & water
Internal filter supplied or to display "Fresh Filtered"
4
6
30 minute delay
7
8
12
Fig. 13
ON
Six-month PM disabled
Dispenser and Ice machine 7CI100A/7FS100A
Cleaning and Sanitizing –––––––––––––––––––––––––––––––––––––––––––––
Cleaning and sanitizing should be performed at least every 6 months (more often
if local water conditions dictate). For initial startup, only sanitizing is required.
Fig. 14
WARNING!
 Place the dispenser in Maintenance Mode prior to servicing or
cleaning the ice machine. See Maintenance/Cleaning Mode on
page 11.
 For protection, rubber gloves and safety goggles (and/or face shield)
should be worn when handling Cleaner or Sanitizer.
 Do not mix Cleaner and Sanitizer together. It is a violation of federal
law to use these solutions in a manner inconsistent with their labeling.
 Do not use bleach, it will damage the dispenser.
1
3
2
Required Supplies
4
 (3) x 7 oz. SafeCLEAN™ environmentally-friendly ice machine cleaner
packets
 Nu-Calgon IMS-II sanitizing concentrate
 Funnel and Bucket
Cleaning: Ice machine and Dispenser
1. Dispense all the ice out of the unit.
2. Press and hold maintenance/clean switch until
displays in the user
interface to enter Maintenance Mode.
3. Remove (unscrew) chrome ice dispense chute (Fig. 14.1).
6
4. Remove drip tray (Fig. 14.2).
5. Remove (2) screws located behind the drip tray (Fig. 14.3).
6. Move front panel and place on top or beside unit (Fig. 14.4).
7. Remove plug cap from the end of drain tube (Fig. 14.5) and lower tube
7
to drain water into bucket.After the system has been drained of water
5
replace plug cap in drain tube.
8. After the system has been drained of water replace plug cap in drain tube.
9. Secure tube in holder.
10. Remove cap from bin lid cover (Fig. 14.6).
11. Screw bin lid cover cap onto ice discharge chute (Fig. 14.7).
12. Mix SafeCLEAN Ice Machine Cleaner, (3) x 7 oz. packets, with 11.4 L (3 gal.) of water.
13. Pour cleaning solution into bin lid access spout until solution reaches the spout neck.
14. Allow the solution to remain in unit for 15 minutes.
15. While machine is cleaning, remove top and right side panel to access and clean air-cooled condenser.
16. Drain system by lowering drain tube into bucket.
17. Secure drain tube into holder.
18. Fill one time with potable water and drain with tube. Secure drain tube.
Sanitizing: Ice machine and Dispenser
1. Complete steps 1-11 above.
2. Mix a sanitizing solution of 9.5 L (2.5 gal.) of water and 118 ml (4 oz.) of Nu-Calgon IMS-II sanitizing
concentrate.
3. Pour sanitizing solution into bin lid access spout until solution reaches the spout neck.
4. Allow the solution to remain in unit for 5 minutes.
5. Drain system by lowering drain tube.
6. Secure drain tube into holder.
7. Fill and drain three times with potable water.
8. Place a bucket under the dispense chute and remove cap. Note: Some sanitizing solution will remain and
drain out when cap is removed. Reposition cap on bin lid spout.
9. Reinstall front panel, ice dispense chute, and drip tray.
10. Press and hold maintenance/clean switch to exit Maintenance Mode.
Dispenser and Ice machine 7CI100A/7FS100A
13
Cleaning and Sanitizing
(continued)
––––––––––––––––––––––––––––––––––––––
Cleaning: User Interface and Exterior Cabinet
1. Press and release maintenance/clean switch so that only "FRESH FILTERED ICE AND WATER" displays
in the user interface to enter Cleaning Mode (and disable dispensing).
2. Plastic parts, including the user interface, can be cleaned with a non-abrasive glass cleaner. Clean
stainless steel panels with stainless steel cleaner.
3. Press and release maintenance/clean switch to put unit back into service.
Service –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
LED Indicator Description
The LED Indicator is located behind the front panel.
LED Name
Clean
LED Color
Power ON
Low bin
Making ice
Sleep cycle
Time delay
Low water
Maint
Service
HI amps
HI press
Water leak
Drip tray
PM
Clean
Fig. 15
Description
Green
The dispenser is in Cleaning Mode. Dispenser is disabled to allow for cleaning of front panel.
See Maintenance/Cleaning Mode on page 11.
N/A
Not used.
PM
Red
Six-month periodic maintenance required.
Drip tray
Red
Drip tray full.
Water leak
Red
Internal leak in dispenser.
High amps
Red
Auger gearmotor has exceeded 0.55A. The HI amps and Time delay LEDs will illuminate,
the machine will shut down for one hour, the LEDs will turn off, and the machine will resume
normal operation.
Service
Red
8000 hour bushing check (call Follett technical service group at (877) 612-5086 or
+1 (610) 252-7301).
Maintenance
Yellow
Enter Maintenance Mode by pressing and holding maintenance/clean switch for 5 seconds.
Unit will not make or dispense ice.
Low water
Yellow
Insufficient water supply to machine or no low bin LED upon startup.
Time delay
Yellow
Ice production will not resume for at least 15 minutes after a full bin is achieved and a
minimum amount of dispense activity has elapsed.
Sleep cycle
Green
After a full bin and 10 minutes of non-use, the unit goes into standby and will not produce ice
until either 12 hours has elapsed or ice or water has dispensed.
Making ice
Green
Gearmotor, compressor, and fan motor energized.
Low bin
Green
Bin switch closed calling for ice.
Power on
Green
Power supplied to unit.
—
14
Dispenser and Ice machine 7CI100A/7FS100A
Service
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––
Evaporator Disassembly
1.
Fig. 16
Disconnect power from the dispenser.
2. Turn off water supply to dispenser.
2
3. Remove (unscrew) chrome ice dispenser chute
(Fig. 16.1).
4. Remove the drip tray (Fig. 16.2).
1
5. Remove the two screws (Fig. 16.3) on the front panel
(behind the drip tray).
6. Remove and set aside the front panel (Fig. 16.4) - do not
disengage the plug on the back of the User Interface.
7.
Lift and remove the top panel, set aside (Fig. 16.5).
8. Remove two screws (Fig. 16.6) and remove left side
panel.
1
9. Remove two screws (Fig. 16.7) and remove right side
panel.
3
2
4
6
5
7
Dispenser and Ice machine 7CI100A/7FS100A
15
Service
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––
10. Unplug the gear motor (three connectors) (Fig. 16).
Fig. 17
11. Remove ground screw connection.
12. Remove gear motor:
Fig. 18
 Remove M6 allen screw, retainer, spacer and key (Fig. 18.1).
 Remove two M6x90 allen screws (Fig. 18.2).
 Pull gear motor from auger (Fig. 18.3).
 Remove main housing insulation (Fig. 18.4).
13. Remove all traces of petro-gel from auger shaft.
4
2
3
1
2
14. Remove compression nozzle:
Fig. 19
 Loosen hose clamp (Fig. 19.1).
 Remove transport tube (Fig. 19.2).
1
2
16
Dispenser and Ice machine 7CI100A/7FS100A
Service
(continued)
–––––––––––––––––––––––––––––––––––––––––––––––––––
15. Remove M6 socket head allen screw (Fig. 20.1).
Fig. 20
16. Remove compression nozzle retainer (Fig. 20.2).
1
17. Remove compression nozzle (Fig. 20.3).
2
3
18. Remove main housing:
Fig. 21
 Disconnect vent line from T fitting (Fig. 21.1).
1
Dispenser and Ice machine 7CI100A/7FS100A
17
19. Remove three M6x25 socket head allen screws
(Fig. 22.1).
Fig. 22
20. Remove main housing (Fig. 22.2).
2
1
18
Dispenser and Ice machine 7CI100A/7FS100A
Service
(continued)
–––––––––––––––––––––––––––––––––––––––––––––––––––
Fig. 23
21. Remove and discard mating ring and seal (Fig. 23.1).
22. Carefully remove auger (Fig. 23.2).
WARNING!
Use caution when removing auger. The auger is very
sharp - handle with care to avoid personal injury.
2
1
Evaporator Assembly
1.
Fig. 24
Remove and inspect main housing O-ring seal. Replace if
damaged in any way.
2. Clean O-ring groove. Lubricate O-ring with Petro-gel and
reinstall.
3. Use cardboard disc to press new mating ring into main
housing (Fig. 24.1).
1
Cardboard
disc
4. Lube the shaft with liquid soap in the area shown
(Fig. 24.2) and slip on seal and spring (Fig. 24.3).
Note: Do not touch the sealing surfaces with bare hands.
Contact with bare skin will cause premature seal failure.
5. Install auger (Fig. 24.4).
Do NOT
touch!
2
4
3
6. Install main housing:
Fig. 25
 Slide main housing onto auger shaft (Fig. 25.1).
 Install three M6x25 allen screws (Fig. 25.1).
 Connect vent line to T fitting (Fig. 25.1).
3
1
2
Dispenser and Ice machine 7CI100A/7FS100A
19
Service
7.
(continued)
–––––––––––––––––––––––––––––––––––––––––––––––––––
Install compression nozzle:
Fig. 26
 Remove and inspect compression nozzle O-ring seal.
Replace if damaged in any way.
 Clean O-ring groove. Lubricate O-ring with Petro-gel and
reinstall.
 Install compression nozzle (Fig. 26.1).
 Install compression nozzle retainer (Fig. 26.2).
 Install M6 socket head allen screw (Fig. 26.3).
3
2
1
8. Install transport tube (Fig. 27.1).
Fig. 27
9. Tighten hose clamp (Fig. 27.2).
2
1
10. Install gear motor:
Fig. 28
 Install main housing insulation (Fig. 28.1).
 Slide gear motor onto auger shaft (Fig. 28.2).
 Install two M6x90 allen screws (Fig. 28.3).
1
3
2
3
20
Dispenser and Ice machine 7CI100A/7FS100A
Service
(continued)
–––––––––––––––––––––––––––––––––––––––––––––––––––
11. Use screwdriver to orient auger shaft to align with motor
shaft keyway (Fig. 29.1).
Fig. 29
12. Install key into keyway (Fig. 29.2).
2
1
13. Install spacer, ensure that key is captured in slot
(Fig. 30.1)
Fig. 30
1
14. Insert screwdriver into groove of auger shaft and pry shaft
outwards (Fig. 31.1).
Fig. 31
15. Insert retainer into groove (Fig. 31.2), ensure that retainer
is aligned with hole in spacer.
1
2
Dispenser and Ice machine 7CI100A/7FS100A
21
Service
(continued)
–––––––––––––––––––––––––––––––––––––––––––––––––––
16. Install screw and tighten (Fig. 32.1).
Fig. 32
1
2
17. Plug in gear motor (Fig. 33).




22
BLUE to BLUE
BLACK to BLACK
WHITE to WHITE
Connect ground wire with ground screw.
Dispenser and Ice machine 7CI100A/7FS100A
Fig. 33
BL
BL UE to
AC
B
WH K to LUE
B
ITE LA
to CK
WH
ITE
Service
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––
Water Feed Schematic
Evaporator
Float
Water Chute
(optional)
Filter (optional)
Water Solenoid Valve
(optional)
Water Solenoid Valve
Dispenser and Ice machine 7CI100A/7FS100A
23
Service
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––
Bin Melt Water/Evaporator Feed/Clean Out System Schematic
Storage Bin
Vent System Schematic
Storage Bin
Vent Tube
Reservoir
24
Dispenser and Ice machine 7CI100A/7FS100A
Service
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––
Refrigeration Schematic
CONDENSER
FILTER-DRIER
CAP TUBE
COMPRESSOR
EVAPORATOR
ACCUMULATOR
HIGH PRESSURE VAPOR
LOW PRESSURE LIQUID
HIGH PRESSURE LIQUID
LOW PRESSURE VAPOR
Dispenser and Ice machine 7CI100A/7FS100A
25
Service
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––
Condenser Fan Motor Removal
26
Dispenser and Ice machine 7CI100A/7FS100A
Service
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––
User Interface Display Identification
Operation Display
Condition
Procedure
Normal
operation
PM
—
Cleaning Mode
Press and release maintenance/clean
switch to clean the user interface
without dispensing ice or water (see
Maintenance/Cleaning Mode on page
11).
Drip tray full
Empty drip tray.
Six-month
periodic
maintenance
required
Follow Maintenance Mode procedure
(below) and also see Cleaning and
Sanitizing on page 13.
Maintenance
Mode
Enter Maintenance Mode by pressing
maintenance/clean switch until
displays. Complete the cleaning and
sanitizing procedure shown on page
13 and change the filter, if so
equipped. Exit Maintenance Mode by
pressing and holding maintenance/clean
switch until
no longer displays.
Service 8000 hr
bushing check
Call Follett Technical Service Group at
(877) 612-5086 or +1 (610) 252-7301.
The flashing wrench indicates that the
8000 hr bushing check is required.
Dispenser and Ice machine 7CI100A/7FS100A
27
Service
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––
Service Display
Condition
High amps
Procedure
Contact Follett technical service
group at (877) 612-5086 or
+1 (610) 252-7301.
Note: For dispensers after serial
number D45191, the phone
and wrench will not be
illuminated.
28
Dispenser and Ice machine 7CI100A/7FS100A
Internal leak in
dispenser
Locate leak and repair - Press reset
on control board. Contact Follett if
ice machine is leaking.
Sleep mode
Press either dispense button to
return to normal operation.
N
POWER L1
GND
WHITE
#10
WHITE
#17
WHITE/
GRAY
BLACK
GRN-YEL
#11
BLACK
BLUE/
PINK
GRN-YEL
#4
AUGER
FAN
WATER DISPENSE VALVE
BLACK
#18
BLACK
BLACK
#8
BLUE
#7
BLACK
#15
GRN-YEL
#14
BLACK
FAILSAFE SOLENOID VALVE
WHITE
#16
DISP.
#12
P1
L1
L1
L1
P3
P19
P20
P21
FAN
ICE DISP
P6
K4
K7
WHITE
FS
WD
AUGER
CAP
CO2
K6
K5
K2
#13
N
BLUE
#5
N
D21
D22
D19
N
D20
N
N
N
K3
D18
N
N
P5
RESERVOIR
WATER SENSOR
DRIP TRAY WATER
SENSOR
CHASSIS
WATER SENSOR
T2
CURRENT SENS
N
P4
P2
AUGER
GRN-YEL
#19
UV LIGHT
UV ON
D37
#20
#2
P16
P17
WATER LEVELS
BIN
P12 BIN
P12 BIN P11 CLEAN SAFE
S2
P10
SERIAL COMM
HI PRS
P14
WATER AUX
P15
START
RELAY
ICE AUX
P17
WATER LEVELS
YELLOW
ORANGE
BLACK
P18
T1
BLACK
WHITE
S
R
C
O.L.
K1
BLACK
#1
D16
S1
MAINT.
CLEAN
P7
P8 RS485
RS485 UI
P11 CLEAN SAFE
P13 SPARE CTS
P7
RESET
6
2
5
1
PROGRAM
P9
MODEL SELECT
GRN-YEL
#3
COMP.
D1
CLEAN
POWER
LOW BIN
MAKING ICE
SLEEP CYCLE
TIME DELAY
LOW WATER
MAINTENANCE
SERVICE
HI AMPS
HI PRESSURE
WATER LEAK
DRIP TRAY
PM
USER
INTERFACE
RS485 UI
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
(continued)
D17
COMPRESSOR
Service
––––––––––––––––––––––––––––––––––––––––––––––––––––
Electrical Wiring Diagram
Dispenser and Ice machine 7CI100A/7FS100A
29
Parts –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Exterior
6
4
7
5
2
1
30
Dispenser and Ice machine 7CI100A/7FS100A
3
Parts
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––––
Exterior
Reference #
Description
Part #
1
Drip Tray Assy
00957613
2
Panel, Front Assy - Includes Water Nozzle and Plug
00957621
3
Chute, Water (water option)
00957688
4
Panel, Left
00957639
5
Panel, Right
00957647
6
Panel, Top
00957654
7
Panel, Rear
00957662
Not Shown
Cord, 115 VAC
00958058
Not Shown
Packaging for Returns, Dispenser
00957993
Not Shown
Fitting, Elbow - 1/4" FPT x 1/4" Tube
00974261
Not Shown
Drip Tray Drain Kit
00956375
Not Shown
Drip Tray Drain Kit with 4" legs
00981977
Not Shown
Covers, Agion, User Interface
00969030
Dispenser and Ice machine 7CI100A/7FS100A
31
Parts
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––––
Interior
4
7
6
1
12
2
3
5
11
10
10
9
8
32
Dispenser and Ice machine 7CI100A/7FS100A
Parts
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––––
Interior
Reference #
Description
Part #
1
Valve, Dispense Solenoid (water option)
00957704
2
Switch, Cleaning
00957712
3
Drain/Feed Tube with Cap
00957720
4
Valve, Failsafe Solenoid
00957738
5
Compressor with Mounting Hardware
00958009
6
Condenser
00958017
7
Condenser Fan and Cord
00958025
8
Control Board with Stand-offs
00958033
9
Capacitor, Gearmotor
00958041
10
Sensor, Retainer Hardware Kit
00958066
11
Relay and Overload
00958090
12
Refrigeration, Piping Assy
00958132
Dispenser and Ice machine 7CI100A/7FS100A
33
Parts
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––––
Bin Assembly
9
3
4
5
6
2
1
7
8
34
Dispenser and Ice machine 7CI100A/7FS100A
Parts
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––––
Bin Assembly
Reference #
Description
Part #
1
Ice Chute Assembly
00957670
2
Ice Transport Tubing with Insulation
00957746
3
Switch, Shuttle
00957753
4
Shuttle, Complete Assy
00957761
5
Lid, Bin Assy
00957779
6
Bin, Assy
00957787
7
Auger, Dispense
00957795
8
Motor, Dispense
00957803
9
Cap and Insulation, Bin
00957936
Not Shown
For serial numbers D17619 and below:
Bin Cap
00931519
Ice Chute
00927210
Chute Adapter
00926550
Dispenser and Ice machine 7CI100A/7FS100A
35
Parts
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––––
Evaporator Assembly
10
11
12
13
14
13
2
8
5
6
1
3
7
4
9
36
Dispenser and Ice machine 7CI100A/7FS100A
Parts
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––––
Evaporator Assembly
Reference #
Description
Part #
1
Gearmotor Assembly
00957811
2
Main Housing with Front Seal and Screws
00957829
3
Screws, Main Housing
00957837
4
Auger with front seal (includes gearmotor hardware kit)
00957845
5
Ice Compression Nozzle Assy
00957852
6
Front Seal and O-Ring
00957860
7
Evaporator Assembly with Insulation
00957878
8
Housing, Bushing with Insulation
00957886
9
Hardware kit, Gearmotor (For serial numbers E01087 and above)
01048628
9
Hardware kit, Gearmotor (For serial numbers below E01087)
00957894
10
Reservoir and Float Complete Assy
00957902
11
Lid, Reservoir with Insulation and O-Ring
00957910
12
Float Valve
00957928
13
“T” Fitting - 1/4"
502923
14
Tubing - 1/4"
502079
Miscellaneous
Reference #
Description
Part #
Not Shown
Water filter cartridge, 5 micron
00968107
Not Shown
Cleaning and sanitizing kit, single use
00979856
Not Shown
SafeClean, case of 24
00132001
Not Shown
IMS II sanitizer concentrate, 16 oz
00979674
Dispenser and Ice machine 7CI100A/7FS100A
37
Parts
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––––
Base Stand
2
1
38
Dispenser and Ice machine 7CI100A/7FS100A
Parts
(continued)
––––––––––––––––––––––––––––––––––––––––––––––––––––––
Base Stand
Reference #
Description
Part #
1
Front Panel, Base
00958108
2
Latches with Bayonets, Base
00958116
Not Shown
Tray, Base
00958124
Not Shown
Packaging for Returns, Base
00957985
Reference #
Description
Part #
Not Shown
Water filter cartridge, 5 micron
00968107
Not Shown
Cleaning and sanitizing kit, single use
00979856
Not Shown
SafeClean, case of 24
00132001
Not Shown
IMS II sanitizer concentrate, 16 oz
00979674
Not Shown
6" (15.24 cm) Legs for base stand, set of 4
00956318
Not Shown
4" (10.16 cm) Legs for countertop dispenser, set of 4
00956300
Miscellaneous
Dispenser and Ice machine 7CI100A/7FS100A
39
SafeCLEAN is a trademark of Follett Corporation.
Follett is a registered trademark of Follett Corporation, registered in US.
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
00951640R07
© Follet Corporation 8/13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising