Tektronix TLA 700 700 Series Logic Analyzer User Manual

Tektronix TLA 700 700 Series Logic Analyzer User Manual

Below you will find brief information for Logic Analyzer TLA 700 Series. The TLA 700 Series Logic Analyzer is a powerful tool for debugging and analyzing digital systems. It can be used to capture and display signals from a variety of devices, including microprocessors, microcontrollers, and digital circuits. The logic analyzer can also be used to perform a variety of analysis tasks, such as timing analysis, state analysis, and data analysis.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Tektronix Logic Analyzer TLA 700 Series User Manual | Manualzz
User Manual
TLA 700 Series
Logic Analyzer
070-9775-04
This document supports application software
version 2.0 and above.
Copyright © Tektronix, Inc. All rights reserved. Licensed software products are owned by Tektronix or its suppliers and
are protected by United States copyright laws and international treaty provisions.
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the
Rights in Technical Data and Computer Software clause at DFARS 252.227-7013, or subparagraphs (c)(1) and (2) of the
Commercial Computer Software – Restricted Rights clause at FAR 52.227-19, as applicable.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
Printed in the U.S.A.
Tektronix, Inc., P.O. Box 1000, Wilsonville, OR 97070–1000
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
MagniVu is a trademark of Tektronix, Inc.
Windows and Windows 95 are trademarks of Microsoft Corporation.
WARRANTY
Tektronix warrants that the products that it manufactures and sells will be free from defects in materials and workmanship
for a period of one (1) year from the date of shipment. If a product proves defective during this warranty period, Tektronix,
at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in
exchange for the defective product.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the
warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for
packaging and shipping the defective product to the service center designated by Tektronix, with shipping charges prepaid.
Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the
Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any
other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting
from attempts by personnel other than Tektronix representatives to install, repair or service the product; b) to repair
damage resulting from improper use or connection to incompatible equipment; c) to repair any damage or malfunction
caused by the use of non-Tektronix supplies; or d) to service a product that has been modified or integrated with other
products when the effect of such modification or integration increases the time or difficulty of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’ RESPONSIBILITY TO
REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO
THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE
LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE
OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGES.
WARRANTY
Tektronix warrants that the media on which this software product is furnished and the encoding of the programs on the
media will be free from defects in materials and workmanship for a period of three (3) months from the date of shipment.
If a medium or encoding proves defective during the warranty period, Tektronix will provide a replacement in exchange
for the defective medium. Except as to the media on which this software product is furnished, this software product is
provided “as is” without warranty of any kind, either express or implied. Tektronix does not warrant that the functions
contained in this software product will meet Customer’s requirements or that the operation of the programs will be
uninterrupted or error-free.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the
warranty period. If Tektronix is unable to provide a replacement that is free from defects in materials and workmanship
within a reasonable time thereafter, Customer may terminate the license for this software product and return this software
product and any associated materials for credit or refund.
THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’ RESPONSIBILITY TO
REPLACE DEFECTIVE MEDIA OR REFUND CUSTOMER’S PAYMENT IS THE SOLE AND EXCLUSIVE
REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS
VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF
THE POSSIBILITY OF SUCH DAMAGES.
Table of Contents
General Safety Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xi
xiii
Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contacting Tektronix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xiii
xv
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1–1
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powering On the Logic Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powering Off the Logic Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Probes to the Target System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Approaching the Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programmatic Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backing Up User Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Portable Mainframe Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
For Further Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1–1
1–2
1–2
1–3
1–3
1–6
1–17
1–17
1–18
1–20
Sampling and Digitizing a Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LA Module Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSO Module Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logic Analyzer Physical Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logic Analyzer Conceptual Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intermodule Interactions and Time Correlation . . . . . . . . . . . . . . . . . . . . . . . . . .
Listing-Data Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Microprocessor Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-Level Language (HLL) Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Waveform Data Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performance Analysis Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Comparing Acquired Data Against Saved Data . . . . . . . . . . . . . . . . . . . . . . . . . .
Repetitive Acquisitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TLA 700 Programmatic Interface (TPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbol Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–1
2–2
2–4
2–5
2–6
2–7
2–8
2–9
2–10
2–11
2–17
2–18
2–19
2–20
2–21
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–1
Starting From the System Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Up the LA Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Up the Trigger Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Up the DSO Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Arming Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intermodule and External Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Merging Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–1
3–3
3–12
3–24
3–30
3–31
3–32
3–34
Getting Started
Operating Basics
Reference
TLA 700 Series Logic Analyzer User Manual
i
Table of Contents
ii
Saving and Loading Setups, Triggers, and Data . . . . . . . . . . . . . . . . . . . . . . . . .
System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu Shortcut Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–35
3–39
3–40
Acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–41
Starting and Stopping Acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Viewing Acquisition Activity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If the Logic Analyzer Does Not Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–41
3–43
3–44
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–47
Opening an Existing Data Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening a Saved Data Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aligning Saved Data with Current Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating a New Data Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Purpose Data Window Shortcut Keys . . . . . . . . . . . . . . . . . . . . . . . . . .
3–48
3–49
3–49
3–50
3–51
Waveform Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–53
Types of Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reading the Waveform Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cursor Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jumping to Specific Data Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Searching Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locking Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MagniVu Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Comparing Waveform Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Waveform Data View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customizing the Waveform Window Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exporting Waveform Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printing Waveform Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Waveform Window Shortcut Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–54
3–56
3–58
3–59
3–60
3–61
3–62
3–63
3–65
3–68
3–68
3–69
3–70
Listing Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–71
Reading the Listing Window Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jumping to Specific Data Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measuring Listing Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Comparing Listing Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Searching Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locking Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MagniVu Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Listing Data View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customizing the Listing Window Data Area . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exporting Listing Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printing Listing Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Listing Window Shortcut Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–71
3–73
3–75
3–75
3–77
3–78
3–79
3–79
3–81
3–82
3–85
3–86
Source Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–87
Creating a Source Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reading the Source Window Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jumping to Specific Data Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Moving Through Source Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Searching for Source Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Source Data View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customizing the Source Window Data Area . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locating Source Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printing Source Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Source Window Shortcut Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–88
3–89
3–90
3–92
3–95
3–96
3–97
3–97
3–99
3–100
TLA 700 Series Logic Analyzer User Manual
Table of Contents
Histogram Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–101
Measuring Histogram Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating a Histogram Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Histogram Data View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customizing the Histogram Window Data Area . . . . . . . . . . . . . . . . . . . . . . . . .
Exporting Histogram Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printing Histogram Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Histogram Window Shortcut Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–102
3–103
3–104
3–105
3–106
3–107
3–108
Appendices
Appendix A: Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A–1
Characteristic Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TLA 704 Color Portable Mainframe Characteristics . . . . . . . . . . . . . . . . . . . . . .
TLA 711 Color Benchtop Chassis Characteristics . . . . . . . . . . . . . . . . . . . . . . . .
TLA 711 Color Benchtop Controller Characteristics . . . . . . . . . . . . . . . . . . . . .
TLA 700 Series Logic Analyzer Module Characteristics . . . . . . . . . . . . . . . . . .
TLA 700 Series Digitizing Oscilloscope Module Characteristics . . . . . . . . . . . .
A–1
A–8
A–12
A–15
A–17
A–24
Appendix B: TLA 700 Symbol File Format . . . . . . . . . . . . . . . . . . . . .
B–1
TSF Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TSF Pattern Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TSF Range Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B–2
B–3
B–4
Appendix C: User Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C–1
General Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module Self Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
In Case of Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repacking for Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C–1
C–1
C–2
C–4
C–4
Appendix D: Probe and Connector Information . . . . . . . . . . . . . . . . .
D–1
P6417 Probe Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P6434 Probe Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Benchtop Mainframe Remote On/Standby Switch . . . . . . . . . . . . . . . . . . . . . . .
D–1
D–2
D–3
Glossary
Index
TLA 700 Series Logic Analyzer User Manual
iii
Table of Contents
List of Figures
iv
Figure 1–1: Portable and benchtop mainframes . . . . . . . . . . . . . . . . .
Figure 1–2: On/Standby switch locations . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–3: P6417 17-channel probe . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–4: P6434 high-density probe connections . . . . . . . . . . . . . . .
Figure 1–5: Window usage control flow . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–6: System window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–7: DSO Setup window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–8: LA Setup window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–9: LA Trigger window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–10: Trigger library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–11: DSO Trigger window . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–12: Listing window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–13: Waveform window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–14: Histogram window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–15: Source window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–16: Comparing regular and MagniVu data . . . . . . . . . . . . .
Figure 1–17: Save and Load operations in the File menu . . . . . . . . . .
Figure 1–18: Using a property sheet to customize the display . . . . . .
Figure 1–19: Portable mainframe front panel . . . . . . . . . . . . . . . . . . .
Figure 1–20: GlidePoint pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–21: Locations of external connectors . . . . . . . . . . . . . . . . . . .
1–1
1–2
1–4
1–5
1–6
1–7
1–8
1–8
1–9
1–10
1–10
1–11
1–12
1–13
1–14
1–15
1–16
1–17
1–18
1–18
1–19
Figure 2–1: Acquiring a digital signal (LA module) . . . . . . . . . . . . . .
Figure 2–2: Acquiring an analog signal (DSO module) . . . . . . . . . . . .
Figure 2–3: Block diagram of the LA module acquisition and
storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–4: Block diagram of the DSO module acquisition and
storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–5: Logic analyzer physical model . . . . . . . . . . . . . . . . . . . . . .
Figure 2–6: Logic analyzer conceptual model . . . . . . . . . . . . . . . . . . .
Figure 2–7: Listing data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–8: Listing window with analog data . . . . . . . . . . . . . . . . . . . .
Figure 2–9: Listing data using a microprocessor support package . .
Figure 2–10: High-level source code . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–11: Source code viewed as acquired data . . . . . . . . . . . . . . .
Figure 2–12: Waveform data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–13: Using the DSO module to capture a runt pulse . . . . . . .
2–1
2–2
2–2
2–5
2–6
2–7
2–8
2–9
2–9
2–10
2–11
2–11
2–13
TLA 700 Series Logic Analyzer User Manual
Table of Contents
Figure 2–14: LA module sampling resolution . . . . . . . . . . . . . . . . . . . .
Figure 2–15: Aliasing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–16: LA module triggering on a glitch . . . . . . . . . . . . . . . . . .
Figure 2–17: DSO module triggering on a glitch . . . . . . . . . . . . . . . . .
Figure 2–18: Viewing the performance of code with a Histogram
window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–19: Using color to show memory differences in a Listing
window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–20: Defining repetitive setups . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–21: Using symbols in a trigger program . . . . . . . . . . . . . . . .
Figure 2–22: Waveforms using pattern symbols . . . . . . . . . . . . . . . . .
Figure 2–23: Listing data using range symbols . . . . . . . . . . . . . . . . . .
Figure 2–24: Symbols dialog box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2–25: Load Symbol Options dialog box . . . . . . . . . . . . . . . . . .
2–19
2–20
2–21
2–23
2–23
2–24
2–25
Figure 3–1: System window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–2: Opening a Waveform window from the System window
Figure 3–3: The LA module Setup window . . . . . . . . . . . . . . . . . . . . .
Figure 3–4: Setup window with the QSTART support package . . . . .
Figure 3–5: Selecting channels for memory compare . . . . . . . . . . . . .
Figure 3–6: Enabling data compare . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–7: Channel grouping table in the Setup window . . . . . . . . .
Figure 3–8: The Activity Indicators dialog box . . . . . . . . . . . . . . . . . .
Figure 3–9: Probe Thresholds dialog box . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–10: LA module Trigger window . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–11: Trigger window structure . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–12: Overview portion of LA Trigger window . . . . . . . . . . . .
Figure 3–13: Trigger detail portion of LA Trigger window . . . . . . . .
Figure 3–14: Using trigger storage . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–15: DSO Setup window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–16: DSO Setup window vertical input settings . . . . . . . . . . .
Figure 3–17: DSO Setup window Horizontal settings . . . . . . . . . . . . .
Figure 3–18: Signals property page . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–19: Merging modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–20: Logic analyzer conceptual model . . . . . . . . . . . . . . . . . .
Figure 3–21: Saving a system with data . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–22: Load System Options dialog box . . . . . . . . . . . . . . . . . . .
Figure 3–23: Saving a file in a personalized trigger library . . . . . . . .
Figure 3–24: Defining setups for Repetitive mode . . . . . . . . . . . . . . . .
3–1
3–2
3–3
3–4
3–5
3–6
3–10
3–11
3–12
3–13
3–14
3–15
3–15
3–23
3–25
3–27
3–28
3–32
3–34
3–35
3–36
3–37
3–38
3–43
TLA 700 Series Logic Analyzer User Manual
2–14
2–15
2–16
2–17
2–18
v
Table of Contents
Figure 3–25: The Status Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–26: The Listing and Waveform windows . . . . . . . . . . . . . . .
Figure 3–27: Opening a data window . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–28: New Data Window wizard . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–29: Waveform window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–30: Waveform types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–31: Magnitude waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–32: Range readouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–33: Waveform window cursors and marks . . . . . . . . . . . . . .
Figure 3–34: Using the Go To dialog box to jump to the
system trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–35: Using the Overview Mark bar to jump to a
data location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–36: Defining search criteria . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–37: Lock Windows dialog box . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–38: MagniVu data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–39: Adding a MagniVu data source to a data window . . . . .
Figure 3–40: Selecting compare data colors in the Waveform
Window property page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–41: Viewing LA compare data in a Waveform window . . . .
Figure 3–42: Add Waveform dialog box . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–43: Waveform with a glitch . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–44: Property page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–45: Listing window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–46: Listing window cursors and marks . . . . . . . . . . . . . . . . .
Figure 3–47: Using the Go To dialog box to jump to the
system trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–48: Using the Overview Mark bar to jump to a
data location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–49: Selecting compare data colors in the Listing
Window property page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–50: Viewing LA compare data in a Listing window . . . . . . .
Figure 3–51: Defining search criteria . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–52: Lock Windows dialog box . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–53: Add Column dialog box . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–54: Export Data dialog box . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–55: Export Data Options dialog box . . . . . . . . . . . . . . . . . . .
Figure 3–56: Source window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–57: Source window cursors and marks . . . . . . . . . . . . . . . . .
vi
3–43
3–47
3–48
3–50
3–53
3–54
3–55
3–55
3–56
3–59
3–59
3–61
3–61
3–62
3–63
3–64
3–65
3–66
3–67
3–68
3–71
3–72
3–74
3–74
3–76
3–77
3–78
3–79
3–80
3–82
3–83
3–87
3–89
TLA 700 Series Logic Analyzer User Manual
Table of Contents
Figure 3–58: Using the Go To dialog box to jump to the
cursor location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–59: Using the Overview Mark bar to jump to a
data location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–60: Source window controls . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–61: Defining source search criteria . . . . . . . . . . . . . . . . . . . .
Figure 3–62: Source Files property page . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–63: Histogram window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3–64: Selecting the data source for the Histogram window . .
Figure 3–65: Measuring events with the Histogram window . . . . . . .
Figure 3–66: Export Histogram dialog box . . . . . . . . . . . . . . . . . . . . .
Figure 3–67: ASCII histogram data file . . . . . . . . . . . . . . . . . . . . . . . .
3–91
3–91
3–92
3–96
3–98
3–101
3–102
3–103
3–106
3–107
Figure A–1: Front and side views of TLA 704 Color Portable
Mainframe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure A–2: Front view and side view of standard Benchtop chassis
Figure A–3: Front view and side view of Benchtop chassis with
Rackmount Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A–14
Figure D–1: P6417 probe footprints . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure D–2: P6417 probe podlet clearance . . . . . . . . . . . . . . . . . . . . . .
Figure D–3: Connector used for remote On/Standby switch . . . . . . .
D–1
D–1
D–3
TLA 700 Series Logic Analyzer User Manual
A–11
A–14
vii
Table of Contents
List of Tables
viii
Table 2–1: Using symbols in logic analyzer windows . . . . . . . . . . . . .
2–22
Table 3–1: LA Trigger library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3–2: Trigger events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3–3: Trigger resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3–4: Trigger actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3–5: Menu shortcut keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3–6: General purpose data window shortcut keys . . . . . . . . . .
Table 3–7: Waveform window cursor and mark summary . . . . . . . .
Table 3–8: Waveform window shortcut keys . . . . . . . . . . . . . . . . . . . .
Table 3–9: Listing window cursor and mark summary . . . . . . . . . . .
Table 3–10: Listing window shortcut keys . . . . . . . . . . . . . . . . . . . . . .
Table 3–11: Source window cursor and mark summary . . . . . . . . . .
Table 3–12: Source window shortcut keys . . . . . . . . . . . . . . . . . . . . . .
Table 3–13: Histogram window shortcut keys . . . . . . . . . . . . . . . . . . .
3–16
3–20
3–21
3–22
3–40
3–51
3–57
3–70
3–72
3–86
3–89
3–100
3–108
Table A–1: Atmospheric characteristics (mainframes and modules)
Table A–2: Backplane interface (portable and benchtop
mainframes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A–3: External signal interface (portable and benchtop
mainframes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A–4: Certifications and compliances: TLA 704 Color Portable
Mainframe1 and TLA 711 Color Benchtop Mainframe1 . . . . . .
Table A–5: Portable mainframe internal controller . . . . . . . . . . . . . .
Table A–6: Portable mainframe display system . . . . . . . . . . . . . . . . .
Table A–7: Portable mainframe front-panel interface . . . . . . . . . . . .
Table A–8: Portable mainframe rear-panel interface . . . . . . . . . . . . .
Table A–9: Portable mainframe AC power source . . . . . . . . . . . . . . .
Table A–10: Portable mainframe secondary power . . . . . . . . . . . . . . .
Table A–11: Portable mainframe cooling . . . . . . . . . . . . . . . . . . . . . . .
Table A–12: Portable mainframe mechanical . . . . . . . . . . . . . . . . . . .
Table A–13: Benchtop chassis AC power source . . . . . . . . . . . . . . . . .
Table A–14: Benchtop chassis secondary power . . . . . . . . . . . . . . . . .
Table A–15: Benchtop chassis cooling . . . . . . . . . . . . . . . . . . . . . . . . .
Table A–16: Benchtop chassis mechanical . . . . . . . . . . . . . . . . . . . . . .
Table A–17: Benchtop controller characteristics . . . . . . . . . . . . . . . .
Table A–18: Benchtop controller mechanical characteristics . . . . . .
Table A–19: LA module channel width and depth . . . . . . . . . . . . . . .
A–2
A–3
A–5
A–7
A–8
A–8
A–9
A–9
A–10
A–10
A–11
A–11
A–12
A–12
A–13
A–13
A–15
A–16
A–17
TLA 700 Series Logic Analyzer User Manual
Table of Contents
Table A–20: LA module clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A–21: LA module trigger system . . . . . . . . . . . . . . . . . . . . . . . .
Table A–22: LA module input parameters (with P6417 Probe) . . . . .
Table A–23: LA module MagniVu feature . . . . . . . . . . . . . . . . . . . . . .
Table A–24: Merged LA modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A–25: LA module data handling . . . . . . . . . . . . . . . . . . . . . . . .
Table A–26: LA module mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table A–27: DSO module signal acquisition system . . . . . . . . . . . . . .
Table A–28: DSO module timebase system . . . . . . . . . . . . . . . . . . . . .
Table A–29: DSO module trigger system . . . . . . . . . . . . . . . . . . . . . . .
Table A–30: DSO module front-panel connectors . . . . . . . . . . . . . . . .
Table A–31: DSO module certifications and compliances . . . . . . . . .
Table A–32: DSO module mechanical . . . . . . . . . . . . . . . . . . . . . . . . .
TLA 700 Series Logic Analyzer User Manual
A–17
A–19
A–21
A–21
A–22
A–22
A–23
A–24
A–27
A–27
A–29
A–29
A–30
ix
Table of Contents
x
TLA 700 Series Logic Analyzer User Manual
General Safety Summary
Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it. To avoid potential hazards, use this
product only as specified.
Only qualified personnel should perform service procedures.
To Avoid Fire or
Personal Injury
Use Proper Power Cord. Use only the power cord specified for this product and
certified for the country of use.
Connect and Disconnect Properly. Do not connect or disconnect probes or test
leads while they are connected to a voltage source.
Ground the Product. This product is grounded through the grounding conductor
of the power cord. To avoid electric shock, the grounding conductor must be
connected to earth ground. Before making connections to the input or output
terminals of the product, ensure that the product is properly grounded.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings
and marking on the product. Consult the product manual for further ratings
information before making connections to the product.
The common terminal is at ground potential. Do not connect the common
terminal to elevated voltages.
Do not apply a potential to any terminal, including the common terminal, that
exceeds the maximum rating of that terminal.
Use Proper AC Adapter. Use only the AC adapter specified for this product.
Do Not Operate Without Covers. Do not operate this product with covers or panels
removed.
Use Proper Fuse. Use only the fuse type and rating specified for this product.
Avoid Exposed Circuitry. Do not touch exposed connections and components
when power is present.
Do Not Operate With Suspected Failures. If you suspect there is damage to this
product, have it inspected by qualified service personnel.
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
Provide Proper Ventilation. Refer to the manual’s installation instructions for
details on installing the product so it has proper ventilation.
TLA 700 Series Logic Analyzer User Manual
xi
General Safety Summary
Symbols and Terms
Terms in this Manual. These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
Terms on the Product. These terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read the
marking.
WARNING indicates an injury hazard not immediately accessible as you read the
marking.
CAUTION indicates a hazard to property including the product.
Symbols on the Product. The following symbols may appear on the product:
WARNING
High Voltage
xii
Protective Ground
(Earth) Terminal
CAUTION
Refer to Manual
Double
Insulated
TLA 700 Series Logic Analyzer User Manual
Preface
This manual contains operating information for the TLA 700 Series Logic
Analyzer. The manual consists of the following sections:
H
Chapter 1: Getting Started. Provides basic information about using the logic
analyzer.
H
Chapter 2: Operating Basics. Describes some logic analyzer concepts.
H
Chapter 3: Reference. Describes how to configure and operate the logic
analyzer.
H
Appendix A: Specifications. Lists the environmental, physical, and electrical
properties of the logic analyzer and LA module probes.
H
Appendix B: TLA 700 Symbol File Format. Provides information on the
contents of symbol files using the TLA 700 Symbol File format.
H
Appendix C: User Service. Provides user service information.
H
Appendix D: Probe and Connector Information. Provides logic analyzer
probe and connector information.
Related Documentation
In addition to this user manual, the following documentation is available for your
TLA 700 Series Logic Analyzer:
H
The TLA 700 Series Logic Analyzer Installation Manual provides installation information for the TLA 700 Series Logic Analyzer.
H
The online help provides information about the TLA 700 Series user
interface and the TLA 700 Programmatic Interface (TPI). To view the online
help, select Help Topics from the Help menu.
H
The online release notes provide last-minute product and software information not included in this manual. Refer to Release Notes on page 1–21 for
information on viewing the release notes.
H
A series of microprocessor support instruction manuals provide operating
and service instructions for the individual microprocessor support packages.
H
The TLA 700 Series TLA 7QS QuickStart Training Manual provides training
exercises to help you learn key features of the TLA 700 Series Logic
Analyzer. The training manual is designed to be used with the TLA 7QS
QuickStart training board.
TLA 700 Series Logic Analyzer User Manual
xiii
Preface
xiv
H
The TLA 700 Series TLA 7QS QuickStart Technical Reference Manual
provides technical and service information for the TLA 7QS QuickStart
training board.
H
The TLA 700 Series Performance Verification and Adjustment Technical
Reference Manual provides performance verification and adjustment
procedures for the major components of the TLA 700 Series Logic Analyzer.
The manual includes the performance verification and adjustment software.
H
The TLA 711 Color Benchtop Chassis Service Manual provides board-level
service information for the benchtop chassis.
H
The TLA 711 Color Benchtop Controller Service Manual provides boardlevel service information for the benchtop mainframe controller module.
H
The TLA 704 Color Portable Mainframe Service Manual provides boardlevel service information for the portable mainframe.
H
The TLA 700 Series Logic Analyzer Modules TLA 7Lx and TLA 7Mx Service
Manual provides board-level service information for the LA modules.
H
The TLA 700 Series DSO Modules TLA 7Dx and TLA 7Ex Service Manual
provides board-level service information for the DSO modules.
H
The P6434 Mass Termination Probe Instructions provides instructions for
using the P6434 probes.
TLA 700 Series Logic Analyzer User Manual
Preface
Contacting Tektronix
Product
Support
For application-oriented questions about a Tektronix measurement product, call toll free in North America:
1-800-TEK-WIDE (1-800-835-9433 ext. 2400)
6:00 a.m. – 5:00 p.m. Pacific time
Or, contact us by e-mail:
[email protected]
For product support outside of North America, contact your
local Tektronix distributor or sales office.
Service
Support
Contact your local Tektronix distributor or sales office. Or, visit
our web site for a listing of worldwide service locations.
http://www.tek.com
For other
information
In North America:
1-800-TEK-WIDE (1-800-835-9433)
An operator will direct your call.
To write us
Tektronix, Inc.
P.O. Box 1000
Wilsonville, OR 97070-1000
U.S.A.
TLA 700 Series Logic Analyzer User Manual
xv
Preface
xvi
TLA 700 Series Logic Analyzer User Manual
Getting Started
Getting Started
This chapter provides basic information about using the logic analyzer. There is
information about the physical instrument and introductory information about
how to operate it. Once you have a basic grasp of this information, proceed to
the next chapter, Operating Basics, for a conceptual model of how the logic
analyzer works.
Product Description
The TLA 700 Series Logic Analyzer is a configurable instrument that combines
a high-performance logic analyzer with a digitizing storage oscilloscope. There
are two mainframe styles, portable and benchtop, as shown in Figure 1–1.
Figure 1–1: Portable and benchtop mainframes
Several logic analyzer (LA) modules are available, in various combinations of
channel width and memory depth. All provide simultaneous state and timing
measurements through a single probe.
The LA module implements a feature called MagniVu, an acquisition technology
that enables each of the LA modules to offer 500 picosecond timing resolution
on all channels. MagniVu data is always available for all channels and requires
no additional probing.
TLA 700 Series Logic Analyzer User Manual
1–1
Getting Started
The digitizing storage oscilloscope (DSO) module incorporates digital real-time
signal acquisition. DSO module data is tightly correlated with data from other
modules, for displays and for intermodule triggering and signalling.
The user interface is built on the familiar Windows 95 operating system. In
addition to using an interface you probably already know, this means that you
can install any PC-compatible, third-party hardware and software on the
instrument.
Installation
Installation information for the TLA 700 Series mainframe, modules, and
software is located in the TLA 700 Series Logic Analyzer Installation Manual.
Powering On the Logic Analyzer
Power on the logic analyzer as follows:
1. Press the On/Standby switch to power on the logic analyzer (see Figure 1–2
for the switch location).
2. Wait for the logic analyzer to complete power-on self-tests, start Windows,
and start the TLA 700 application.
Figure 1–2: On/Standby switch locations
1–2
TLA 700 Series Logic Analyzer User Manual
Getting Started
Powering Off the Logic Analyzer
The portable mainframe has a built-in soft power-off function that safely powers
off the mainframe when you press the On/Standby switch. If you have the
benchtop mainframe, you must power off the mainframe using the Windows 95
shutdown process before depressing the On/Standby switch.
You can set the shutdown mode in the Mainframe Utilities tool in the Windows 95 control panel.
CAUTION. When powering off the benchtop mainframe, use the Windows 95 shut
down procedure. Powering down the benchtop mainframe prematurely can
corrupt the software on the hard disk.
Connecting Probes to the Target System
The logic analyzer connects to the target system through probes. The LA probes
allow you to connect to the target system in several different ways as shown in
the following illustrations. You can use the color-coded probe channels to map
the hardware connections to the channel settings in the LA Setup window. Each
LA probe group consists of eight channels that can be individually named in the
LA Setup menu.
Connect the probes to the logic analyzer by matching the color-coded label to the
label on the LA module. To provide a secure connection to the LA module, you
can optionally use the probe retainer bracket with the probe connector.
General Purpose
Connections
The P6417 probes provide a means to connect to the target system for most
applications. Figure 1–3 shows different ways to connect the probe to the target
system.
Note the location of the ground connections for the probe:
H
The individual podlets have the ground (GND) engraved on the podlet.
H
When you use the 8-channel leadsets, the ground lead is a single black
connector. Make sure you connect the ground side of the 8-channel lead set
to the ground side of the 8-channel podlet holder.
Refer to Appendix D: Probe and Connector Information for information on
dimensions for the P6417 probes.
TLA 700 Series Logic Analyzer User Manual
1–3
Getting Started
Figure 1–3: P6417 17-channel probe
1–4
TLA 700 Series Logic Analyzer User Manual
Getting Started
High-Density Probe
Connections
The P6434 Mass Termination Probe allows you to connect 34 LA channels to a
microprocessor probe adapter or directly to the target system. To connect to the
target system directly, you must include compatible Mictor connectors in your
circuit board design.
Figure 1–4 shows two ways of connecting the LA module to a target system. For
more information on the P6434 Mass Termination Probe and how to connect it to
your target system, refer to the P6434 Mass Termination Probe Instructions.
Figure 1–4: P6434 high-density probe connections
Microprocessor
Connections
Both the P6417 and the P6434 probes can be connected to microprocessor
adapters. Refer to the documentation that comes with your microprocessor
disassembler package for details about connecting the probes to the microprocessor adapters and to the target system.
TLA 700 Series Logic Analyzer User Manual
1–5
Getting Started
Approaching the Windows
Typically, you use the windows in this application as shown in Figure 1–5.
1 Go to the System window. This is the
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
main access point to the other windows.
5 View data in the data
windows.
4 Click the Run toolbar
button to acquire data.
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
2 Use the Setup windows
to configure the modules.
3 From the LA Trigger window, load a
trigger program from the library and
customize it for your application.
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
Figure 1–5: Window usage control flow
1–6
TLA 700 Series Logic Analyzer User Manual
Getting Started
System Window
The System window is your point-of-entry into the logic analyzer, and functions
as the overall control center.
You can perform the following functions from the System window:
H
Open module and data windows by clicking their buttons. To select a module
without opening its windows, click inside the icon (but not on its buttons).
H
Create new data windows through the New Data Window wizard. You can
create Histogram windows for performance analysis operations and Source
windows to track the execution of source code. You can also create
additional Listing and Waveform windows.
H
Use the System window for an overview of how the modules and data
windows relate to one another. Relationships between modules (if any) are
always shown; to view which modules are associated with a data window,
you must select the module icon.
H
View which modules provide data to each window by clicking the window
name.
H
Enable and disable modules by clicking their On/Off buttons.
H
Save and load files containing setup, trigger, and data information, by means
of selections from the File menu.
Figure 1–6: System window
TLA 700 Series Logic Analyzer User Manual
1–7
Getting Started
Setup Windows
Before you acquire and display data, you must first configure the modules using
the module Setup windows. Each module has its own Setup and Trigger
window; each is set up individually. Generally, you should configure the Setup
windows before the Trigger windows, because some of the Setup window
settings affect Trigger window selections.
Figure 1–7: DSO Setup window
Figure 1–8: LA Setup window
1–8
TLA 700 Series Logic Analyzer User Manual
Getting Started
Trigger Windows
Both modules have their own Trigger windows. The primary purposes of the
Trigger windows are to specify the trigger conditions.
LA Trigger Window. The LA Trigger window is the heart of the logic analyzer.
You can use the Trigger window to define the conditions when the logic analyzer
acquires and stores data. See Figure 1–9.
Figure 1–9: LA Trigger window
You can define simple or complex trigger programs one step at a time to
determine how the logic analyzer finds the data you are interested in.
TLA 700 Series Logic Analyzer User Manual
1–9
Getting Started
Another common method for setting up a trigger program is to load a trigger
program from the trigger library (see Figure 1–10). You can then alter the trigger
program details as necessary.
Figure 1–10: Trigger library
DSO Trigger Window. The DSO Trigger window lets you define how to trigger the
DSO on analog and digital signals.
Figure 1–11: DSO Trigger window
1–10
TLA 700 Series Logic Analyzer User Manual
Getting Started
Data Windows
You can use data windows to display and analyze acquired data from the LA or
DSO modules. The most common data windows are the Listing windows and
Waveform windows. These are the two default windows for a logic analyzer with
a DSO module and a LA module installed.
To display and evaluate complex logic analyzer data, you can create other types
of data windows using the New Data Window wizard (such as the Histogram
window and the Source window). Refer to Creating a New data Window
beginning on page 3–50 for information on creating data windows.
You can have as many data windows as you want to display different data or
different views of the same data.
Listing Windows. Listing windows (see Figure 1–12) display LA data in lists or
columns.
Figure 1–12: Listing window
You can perform the following functions in Listing windows:
H
Place user marks to flag specific data samples for evaluation.
H
Use the scroll bars to move through the data or jump to a specific point in
the data by clicking the Go To toolbar button and selecting a mark.
H
Search for a data event by clicking the Define Search button in the toolbar.
H
Move columns by clicking on their labels to select them, and then dragging
them to a new location.
H
Add columns by clicking the Add Column toolbar button.
TLA 700 Series Logic Analyzer User Manual
1–11
Getting Started
H
Split the window into two panes for viewing data that is offscreen.
Waveform WIndows. Waveform windows (see Figure 1–13) display DSO or LA
waveform data.
Figure 1–13: Waveform window
You can perform the following functions in Waveform windows:
1–12
H
Use the cursors to take time or voltage measurements.
H
Place user marks to flag specific data samples for evaluation.
H
Use the scroll bars to move through the data, or jump to a specific point in
the data by clicking the Go To toolbar button and selecting a mark.
H
Search for a data event by clicking the Define Search button in the toolbar.
H
Move waveforms by clicking on their labels to select them, and then
dragging them to a new location.
H
Add waveforms by clicking the Add Waveform toolbar button.
H
Split the window into two panes for viewing data that is offscreen.
H
View collections of LA module waveforms as busforms.
H
View the value of a LA module waveform group versus time using magnitude mode.
TLA 700 Series Logic Analyzer User Manual
Getting Started
Histogram Window. Histogram windows (see Figure 1–14) display LA data as
histograms. You use Histogram windows to evaluate the performance of
software; this is also known as performance analysis.
Figure 1–14: Histogram window
You can perform the following functions in Histogram windows:
H
Use the scroll bars to move through the data.
H
Sort histogram data by ranges, counts, or percentages.
H
Change the magnification of histogram bars to view the data in greater
detail.
H
Split the window into two panes for viewing data that is off screen.
H
View various statistics on the acquired data.
TLA 700 Series Logic Analyzer User Manual
1–13
Getting Started
Source Windows. Source windows (see Figure 1–15) display source data. You
can track the execution of source code based on the data displayed in a Listing
window.
Figure 1–15: Source window
You can perform the following functions in Source windows:
1–14
H
Step through source code statements.
H
Turn source code line numbers on or off.
H
Place user marks to flag specific data samples for evaluation.
H
Use the scroll bars to move through the data, or jump to a specific point in
the data by clicking the Go To toolbar button and selecting a mark.
H
Search for source code statements by clicking the Define Search button in
the toolbar.
H
Determine whether there is any acquired data for the corresponding source
file displayed in the Source window.
TLA 700 Series Logic Analyzer User Manual
Getting Started
MagniVu Data
The LA modules have MagniVu data acquisition as a standard feature. MagniVu
acquisition offers 500 picosecond high-resolution timing simultaneous with
200 MHz state on all channels through the same probes; no double-probing is
required. The example shown in Figure 1–16 shows regular data and MagniVu
data for the same channels. You can easily add MagniVu data with the Add
Waveform toolbar button.
Figure 1–16: Comparing regular and MagniVu data
Saving and Loading
Setups and Data
Once you set up the logic analyzer to your satisfaction you will probably want to
save the setup for future use. You can save setup information in two ways, as a
saved system file or as a saved module file.
Saved system files contain setup and trigger information for each module as well
as system level information (such as repetitive properties) and data windows for
the logic analyzer. Saved module files contain setup and trigger information for
only the module specified. In both cases you have the option of saving acquired
data with the files.
Execute Save and Load operations from the File menu. For module Save or Load
operations, you must first go to the module Setup or Trigger window.
Save the setups and data in a folder where you can easily retrieve them. For
example, you may want to save the data in the My Documents folder or within a
folder of your own choosing. You should not save the data in a location that may
be difficult to find or in a location (such as the Windows System folder) that may
cause problems with your operating system.
TLA 700 Series Logic Analyzer User Manual
1–15
Getting Started
Avoid using file name extensions other than the default ones supplied by the
system. The logic analyzer may not recognize saved setups with nonstandard file
name extensions.
Saved system and module files both contain trigger program information. When
you load a trigger from the LA Trigger window, you can select a saved system or
module file as the source. When you do so, the logic analyzer extracts only the
trigger information from the file and loads it to the module.
Figure 1–17: Save and Load operations in the File menu
Customizing the Display
You can customize your data windows. Using property sheets, you can control
data window display parameters. Also, many screen elements, such as waveforms, columns, and marks, have their own property sheets.
Open data window property sheets by clicking the Properties toolbar button in
the data window. Open screen element property sheets by double-clicking on the
element or its label.
1–16
TLA 700 Series Logic Analyzer User Manual
Getting Started
Figure 1–18: Using a property sheet to customize the display
Programmatic Control
In addition to controlling the logic analyzer from the user interface, you can use
the TLA 700 Programmatic Interface (TPI) to control the logic analyzer from a
separate program running on the logic analyzer or on a remote host. Information
for using TPI is included as part of the TLA 700 online help. An online TPI user
manual (available in PDF format) can be printed from the logic analyzer.
Backing Up User Files
You should back up your user files on a regular basis. Use the Windows Back Up
tool to back up files stored on the hard disk. The Back Up tool is located in the
System Tools folder in the Accessories folder. Start the tool and determine which
files and folders you want to back up. Use the Windows online help for
information on using the Back Up tool.
In particular, you should frequently back up your user-generated files. For the
logic analyzer, the user-generated files consist of saved system and module files,
which have a .tla file name extension.
TLA 700 Series Logic Analyzer User Manual
1–17
Getting Started
Portable Mainframe Front Panel Controls
The portable version of the mainframe has front panel controls which you can
operate the logic analyzer without the mouse or keyboard.
Changes the value in a selected
box (such as sample rate or
memory depth). With a cursor
selected, the knob controls cursor
position. Does not scroll data.
Moves the display pointer
and selects objects. See
GlidePoint Pad for more
information.
Scrolls data horizontally.
Scrolls data vertically.
Changes the height of
selected waveform
(Waveform window only).
Changes Time/Div in
the Waveform window.
Figure 1–19: Portable mainframe front panel
Keys
For the portable mainframe, you can use the front panel keys as an alternative to
the detachable keyboard. Most keys and key combinations are available via the
front panel.
For key combinations, it is not necessary to hold down more than one key at a
time. For example, you can press SHIFT in the hexadecimal keypad, and then
press a QWERTY key to accomplish a Shift+key combination. The same is true
for other key combinations, such as CTRL and ALT keys.
GlidePoint Pad
For the portable mainframe, you can use the GlidePoint pad as an alternative to
the mouse. To move the pointer, slide your finger lightly over the surface of the
pad. Tap the surface to simulate a click of the left mouse button, or use the
control buttons to select the type of operation.
Figure 1–20: GlidePoint pad
1–18
TLA 700 Series Logic Analyzer User Manual
Getting Started
External Connectors
The mainframe external connectors are shown in Figure 1–21. The following
connections are available:
H
System Trigger In and System Trigger Out, used to receive or send a trigger
from/to an external source.
H
External Signal In and External Signal Out, used to receive or send a signal
from/to an external source.
H
Accessory connections.
For information about the accessory connections, refer to the TLA 700 Series
Logic Analyzer Installation Manual.
PCMCIA
PC cards (2)
SYSTEM TRIG IN
SYSTEM TRIG OUT
SVGA OUT port
COM port
EXTERNAL SIG IN
EXTERNAL SIG OUT
LPT printer port
Portable mainframe (rear view)
SYSTEM TRIG IN
SYSTEM TRIG OUT
PCMCIA
PC cards (2)
SVGA OUT port
COM port
EXTERNAL SIG IN
EXTERNAL SIG OUT
LPT printer port
Benchtop mainframe (front view)
Figure 1–21: Locations of external connectors
TLA 700 Series Logic Analyzer User Manual
1–19
Getting Started
For Further Information
In addition to the information in this manual, you may want to refer to other
documentation for this TLA 700 Series Logic Analyzer.
Online Help
The online help gives detailed information about the logic analyzer and its
modules. Look in the online help for details about user interface selections that
are not described in this manual. The online help also has basic operating
information for microprocessor support products.
To access online help, go to the Help menu, or click the toolbar buttons shown:
Click for Topic help.
Click for What’s This? help on selected object.
Help Topics. Help topics tell you how to perform tasks and describe software
features and selections shown on the screen. There are two types of help topics,
overview topics and task topics.
Overview topics describe application features, such as windows. Overview topics
may also describe concepts. Overview topics are available through the Help
menu and through Help buttons in dialog boxes. From the Help menu, click Help
Topics, and locate the topic using the Contents or Index tab. The Help on
Window selection in the Help menu provides overview help for the currently-selected window.
Task topics provide procedure information about how to perform specific tasks.
Task topics are available through the Help menu. From the Help menu, click
Help Topics, and locate the topic using the Contents or Index tab.
What’s This? Help. What’s This? help provides a short description of the control
or screen feature selected. First click the What’s This? button on the toolbar, and
then click the item of interest. For further information about the item, go to the
Topic help.
TPI Online Help. Select Help on TPI from the drop-down help menu for
information on using the TLA 700 Programmatic Interface. You can also print
hard copies of the TPI help from a PDF file.
1–20
TLA 700 Series Logic Analyzer User Manual
Getting Started
Windows 95 Online Help. Information about Windows features is available
through the Windows help system. Access Windows help as you would with any
Windows application:
1. Go to the Windows 95 toolbar and click Start.
2. Select Help.
Release Notes
The online Release Notes contain information about this release of the logic
analyzer application. Check the Release Notes for information such as software
compatibility and software version differences from last release.
To access the Release Notes, follow these steps:
1. Go to the Windows 95 toolbar and click Start.
2. Select Programs → Tektronix TLA 700 → TLA 700 Release Notes.
Additional Related
Documentation
Refer to Related Documentation on page xiii for a list of documentation for your
TLA 700 Series Logic Analyzer.
TLA 700 Series Logic Analyzer User Manual
1–21
Getting Started
1–22
TLA 700 Series Logic Analyzer User Manual
Operating Basics
Operating Basics
This chapter provides an overview of the TLA 700 logic analyzer and basic logic
analyzer concepts.
To acquire and display signals from the target system, the logic analyzer must
perform a complex series of actions. For the most part, these actions are
transparent. However, it can be helpful to understand how the logic analyzer
operates. This knowledge can influence how you approach a logic analysis
problem.
Sampling and Digitizing a Signal
Acquisition is the process of sampling the input signal, digitizing it to convert it
into digital data, and assembling it into a waveform record. The order and
method of accomplishing these functions is different between the LA and DSO
modules.
The LA module converts incoming data into ones and zeros using a comparator
with a user-selectable threshold voltage. If the incoming signal is above the
threshold voltage, it is converted to a one; if it is below the threshold voltage, it
is converted to a zero. After digitizing the data, the LA module samples it at
regular time intervals. The sampled and digitized points are stored in memory
along with corresponding timing information. (See Figure 2–1.)
1 1
1
1 1 1 1 1
Digital values
Threshold voltage
Input signal
0 0
0 0 0
0 0 0
Sample clock
Figure 2–1: Acquiring a digital signal (LA module)
The DSO module samples the voltage level of the signal at regular intervals, and
then converts the sampled analog data into 8-bit digital values. (See Figure 2–2.)
The sampled and digitized points are stored in memory along with corresponding
timing information.
TLA 700 Series Logic Analyzer User Manual
2–1
Operating Basics
+6.0 V +5.5 V
+5.0 V
Digital values
Analog signal
2.5 V
0V
+2.0 V
0V
0V
Sample clock
Figure 2–2: Acquiring an analog signal (DSO module)
LA Module Block Diagram
The LA module is the key element of the instrument. Functionally, the LA module can be divided into several blocks, as shown in Figure 2–3. Refer to the
figure as you read about the functional blocks.
Comparator
Data from
target
system
Probes
Sampler
Threshold
voltage
Memory
Trigger
Clock
Internal (asynchronous) or
External (synchronous)
Figure 2–3: Block diagram of the LA module acquisition and storage
Clocking
Clocks control when data is sampled. Naturally, the point at which you sample
data has a great deal to do with the type and quality of data you acquire. For the
LA module, there are two primary approaches to clocking, external (synchronous) clocking and internal (asynchronous) clocking.
External (Synchronous) Clocking. This clocking mode is called an external or
synchronous clock because the clock is external to the logic analyzer, and is
synchronized to the target system.
2–2
TLA 700 Series Logic Analyzer User Manual
Operating Basics
The signal you chose as the external clock to the logic analyzer should be the
same signal that controls the activity of the other signals you want to observe.
For example, to observe the output states of a counter chip, you might use the
clock input to the counter chip to act as the external clock source to the logic
analyzer. With this setup, each clock pulse to the counter chip could also be used
to clock data from the counter’s output lines into the logic analyzer. As another
example, to record the data being written to a latch, you could use the load signal
to the latch as the external clock source to the logic analyzer.
Internal (Asynchronous) Clocking. Much activity can occur in the target system
between system clock signals. Using the LA module’s internal (asynchronous)
clock, you can view all activity in the target system, not just the data available at
the target system clock signal.
Internal clocking is the best choice when you are primarily interested in the
timing aspects of the data. Internal clocking is a natural choice for waveform
timing analysis. It is important to note, however, that the value of internal
clocking is not limited to just displaying waveforms. For a detailed picture of
data activity both during and between state changes, use internal clocking. For
example, when you use internal clocking you are able to acquire and display
glitch information in either the Waveform or Listing windows.
Acquiring Data
Triggering and Storage
Qualification
When you start an acquisition, the logic analyzer begins sampling data from the
probes. Then, each time a sample clock occurs, data is sampled. Sampled data is
then sent to the trigger functional block and to the main memory.
The trigger program looks at sampled data for specific events and then takes a
specified action. The trigger program can look for events, such as data values,
data ranges, or signals from another module. You can also use internal counters
to trigger when the counter reaches a specified value.
When the trigger condition is satisfied, the LA module enables its posttrigger
delay counter to allow the posttrigger portion of the acquisition memory to fill
before stopping acquisition.
The trigger function block includes storage qualification that looks at sampled
data. If the storage conditions are met, a storage qualifier signal enables sampled
data to pass into the acquisition memory as qualified data. Any unqualified data
samples are excluded.
TLA 700 Series Logic Analyzer User Manual
2–3
Operating Basics
Storing Data in Memory
The acquisition memory works like a circular buffer, storing every qualified data
sample until the entire memory is full. After that, each new data sample
overwrites the oldest existing sample. This process continues until the trigger
event is found and the posttrigger delay counter reaches the specified value
(based on the trigger position selection), which stops acquisition. During
acquisition, you can monitor the progress of the data storage process using the
Status Monitor.
After storing the data you can display the acquired data in the Listing or
Waveform data windows.
DSO Module Block Diagram
The DSO module adds analog analysis capability to the instrument. Functionally,
the DSO module can be divided into several blocks, as shown in Figure 2–4.
Refer to the figure as you read about the functional blocks.
Probes
Acquiring Data
A probe interface detects the attenuation factor of each probe. This information is
used to set the vertical scale.
When you start an acquisition, the DSO module begins sampling data from the
probes. Each time a sample clock occurs, data is sampled. Signals from the
probes go to the attenuators/preamp functional block, which is responsible for
input coupling, termination, bandwidth, offset, and full scale range. The DSO
module always uses internal clocking.
From the attenuators/preamp, signals are sent to the acquisition unit and trigger
functional blocks.
Acquisition Unit
Triggering
The acquisition unit functional block samples the input signals and converts
them to digital data.
The DSO trigger looks at sampled data for a specific event. The trigger can look
for various types of events, such as glitches, setup and hold violations, runt
pulses, or signals from another module.
When the trigger event is found, the DSO module enables its posttrigger delay
counter to allow the posttrigger portion of the acquisition memory to fill before
stopping acquisition. When triggered, the DSO module performs its specified
trigger action (for example, triggering all modules).
2–4
TLA 700 Series Logic Analyzer User Manual
Operating Basics
System clock
Data from
target
system
Probes
Attenuators/
preamp
Acquisition
unit
Memory
Trigger
Figure 2–4: Block diagram of the DSO module acquisition and storage
Storing Data in Memory
The acquisition memory works like a circular buffer, storing data samples until
the entire memory is full. After that, each new data sample overwrites the oldest
existing sample. This process continues until the trigger occurs and the posttrigger delay counter reaches the specified value (based on the trigger position
selection), which stops acquisition. During acquisition, you can monitor the
progress of the data storage process using the Status Monitor.
After storing the data you can display the acquired data in the data windows. In
the Waveform window, the data is shown as analog waveforms. In the Listing
window, the data is shown as a series of voltage values.
Logic Analyzer Physical Model
Physically, the logic analyzer is made up of two main parts: the modules and the
mainframe. Figure 2–5 illustrates the relationship between the logic analyzer and
its subparts.
TLA 700 Series Logic Analyzer User Manual
2–5
Operating Basics
Logic Analyzer
Mainframe
Mechanical housing
Display
Communications bus
Controller
Disk drives
Power supply
User interface software
Low-level software
Module 1
Module 2
Module n
Module
Probes
Firmware
Module
Probes
Firmware
Module
Probes
Firmware
Figure 2–5: Logic analyzer physical model
Logic Analyzer Conceptual Model
Conceptually, the logic analyzer is made up of two main parts: the modules and
the system. From the operational perspective, a module encompasses the setup,
trigger, and data associated with the physical LA or DSO module installed in the
logic analyzer. See Figure 2–6. The system refers to the setup and data for the
whole logic analyzer, including all the modules.
Some actions occur at the module level, some at the system level. For example,
you can save either module or system files. When you save a module, you save
all the setup and trigger information for that module. (You also have the option
of saving the data for that module.) When you save a system, you save all the
setup information for the system, including data window display settings, and all
the module information, as well.
2–6
TLA 700 Series Logic Analyzer User Manual
Operating Basics
System
Data Windows
General Settings
Module 1
Setup
Trigger
Data
Module 2
Setup
Trigger
Data
Module n
Setup
Trigger
Data
Figure 2–6: Logic analyzer conceptual model
Intermodule Interactions and Time Correlation
Each module has its own setup, trigger, and clocking functions. (LA modules
may include microprocessor support as part of their setup.) Each module also
acquires and stores its own data.
When you start an acquisition, all modules start acquiring data together.
(Exceptions are when one module has been programmed to arm another or when
a module has been turned off.) Modules stop acquiring data individually,
according to their trigger programming. You also have the option of setting the
logic analyzer to operate in repetitive mode, in which the modules acquire data
and update the data windows continually until you manually stop the acquisition.
Modules readily communicate with one another by means of their trigger
programs. You can specify functions such as the following:
H
Trigger all modules (system trigger)
H
One module arms another
H
Modules respond to events declared by another module (internal signals)
After the modules have captured and stored data, you can view the data in a
Listing or Waveform window. All data is time-correlated in the display,
regardless of its source. Due to the precise time stamp information stored with
the data, and the tightly-integrated communications between modules, the logic
analyzer interleaves data acquired from various sources. Because time stamp
information is always stored with the data, you can also compare saved data and
current data with no loss of accuracy.
MagniVu data is also time-correlated with regular data. Because MagniVu data is
always present, you can easily compare a normal acquisition with its MagniVu
counterpart.
TLA 700 Series Logic Analyzer User Manual
2–7
Operating Basics
Listing-Data Concepts
In many cases, you will use the logic analyzer to observe the data flow in the
target system. The data recorded by the logic analyzer can be displayed in a
listing format, as shown in Figure 2–7.
Listing data is a table of sequential operations performed by the target system. In
the Listing window, each data sample is displayed sequentially. Because each
data sample includes time stamp information, it is a straightforward process to
display acquisitions from multiple data sources. Samples from all specified data
sources are interleaved in chronological order. For clarity, each line in the table
represents a single data sample from a single data source.
You control the presentation of the data by selecting the display radix of the
columns. You can also make other format selections such as font size, color, and
column width.
Figure 2–7: Listing data
You can include data acquired by the DSO module in the Listing window. The
Listing window in Figure 2–8 shows DSO module Channel 1 data as discrete
voltage levels. As with any module, the data samples from the DSO module are
time-correlated with the other data and appear on separate lines.
2–8
TLA 700 Series Logic Analyzer User Manual
Operating Basics
Figure 2–8: Listing window with analog data
Microprocessor Support
For microprocessor applications, the acquired data can be disassembled back into
the assembly language mnemonics used by a particular microprocessor.
Figure 2–9 shows an example of the disassembled mnemonic display format.
Microprocessor support usually requires a special input probe dedicated to a
specific microprocessor.
Figure 2–9: Listing data using a microprocessor support package
TLA 700 Series Logic Analyzer User Manual
2–9
Operating Basics
The logic analyzer provides support for a wide variety of different microprocessors. Microprocessor support packages include the software, probe adapters, and
documentation.
High-Level Language (HLL) Support
You can correlate the high-level language (HLL) source code that you wrote with
your code as it was executed on your target system and acquired by the logic
analyzer. The correlation is based on symbolic information which is extracted
from your object file or load module. You configure the logic analyzer to access
your source files.
You can step through each executed source statement in the Source window and
view the results in a correlated Listing window. You can also set user-defined
marks as break points within the code and then trace the execution of the code
between the marks. Figure 2–10 shows an example of viewing source code in a
Source window, while Figure 2–11 on page 2–11 shows the actual acquired data
in an associated Listing window.
Figure 2–10: High-level source code
2–10
TLA 700 Series Logic Analyzer User Manual
Operating Basics
Figure 2–11: Source code viewed as acquired data
The LA module supports a wide variety of object files including IEEE695,
OMF86, OMF286, OMF386, COFF, Elf/Dwarf, Elf/Stabs, and the TLA 700
Symbol File format (TSF).
Waveform Data Concepts
You can use the logic analyzer to observe the timing relationships between
signals by displaying the recorded signal activity as a series of waveforms in the
Waveform window. Figure 2–12 shows waveform data from an LA module.
Figure 2–12: Waveform data
TLA 700 Series Logic Analyzer User Manual
2–11
Operating Basics
Each waveform is displayed in a separate track, but all waveforms are timealigned horizontally and displayed in the same time per division. Again, the
inclusion of time stamp information with the stored data samples makes it a
straightforward process to display time-correlated acquisitions from multiple
data sources.
You control the horizontal scale of the acquired data in the display. (You do not,
however, change setup parameters by changing settings in the waveform
display.) You can also make other format selections such as channel group radix,
waveform color, and track height. To show when the logic analyzer sampled the
data, you can add Sample using the Add Waveform toolbar button.
When viewing LA data, you can view the data as individual channels. You can
also display the LA data in groups of channels known as busforms. Use the
busforms to display when data changes with respect to clock or control signals.
When you are interested in displaying the value of a group of channels over a
period of time, you can use magnitude mode. For example, using magnitude
mode, you can view the channels connected to a 16-bit digital counter. The
magnitude waveform appears as a sawtooth waveform as the counter values
increment from the minimum value (00) to the maximum value (FF).
LA Module Versus DSO
Module Waveforms
A logic analyzer waveform appears to have zero-length rise and fall times. This
is because the logic analyzer is recreating the waveform from the samples stored
in its memory, which are either ones or zeros.
No electronic signal is perfectly digital in nature; there is always some analog
component. Consider a fast-rising pulse with ringing on the front edge, or
glitches that can occur in a noisy circuit. If you suspect problems caused by
analog signal characteristics (such as signal voltages higher or lower than
specified voltage levels, or slow transition times), you should use a DSO module
to observe the voltage characteristics of the signal. Figure 2–13 shows where the
DSO module captured a runt pulse that was below the logic analyzer’s threshold.
2–12
TLA 700 Series Logic Analyzer User Manual
Operating Basics
Figure 2–13: Using the DSO module to capture a runt pulse
Sampling Resolution
The accuracy of the waveform recreated from the sampled data depends on the
sample clock rate used to record the incoming signals. This is due to the fact that
the waveform re-created by the logic analyzer is based on the sampled signals
stored in its memory. If the sample clock rate is too low, the recorded data will
produce an inaccurate display. Figure 2–14 shows how the sample clock rate can
affect an LA module waveform.
Insufficient DSO module sampling resolution can result in aliasing. For
information about aliasing, see page 2–14.
TLA 700 Series Logic Analyzer User Manual
2–13
Operating Basics
Example 1: Slow sample clock
Original waveform
Sample clock
Displayed waveform
Example 2: Fast sample clock
Original waveform
Sample clock
Displayed waveform
Figure 2–14: LA module sampling resolution
Signal Resolution and
Signal Duration
There is an important trade-off between the resolution of the recorded signal and
its duration in terms of elapsed time. Because the total number of samples that
can be recorded by the logic analyzer is fixed by the depth of the logic analyzer’s acquisition memory, increasing the sample clock rate provides better signal
resolution at the expense of reducing the duration of the captured signal. That is,
a faster sample clock rate will record a smaller portion of the signal, but with
better resolution.
For the LA module it is important to remember that you have an additional tool
to offset the signal resolution/signal duration relationship. By using the MagniVu
data feature, you can view high-resolution data centered about the LA module
trigger. This allows you to zoom in on the data of particular interest while still
maintaining visibility of a more extended signal duration.
Preventing Aliasing
2–14
Under certain conditions, an analog waveform can be aliased on screen. When a
waveform aliases, it appears on screen with a frequency lower than the actual
waveform being input or it appears unstable. Aliasing occurs because the
instrument cannot sample the signal fast enough to construct an accurate
waveform record. (See Figure 2–15.)
TLA 700 Series Logic Analyzer User Manual
Operating Basics
Actual high-frequency
waveform
Apparent low-frequency
waveform due to aliasing
Sampled points
Figure 2–15: Aliasing
To check for aliasing, increase the sampling rate (decrease the clock sample
period) in the module Setup window. If the shape of the displayed waveform
changes drastically or becomes stable at a faster clock sample period setting,
your waveform was probably aliased.
Although the principles of sampling theory define a minimum sample rate of 2X,
a good rule of thumb is to choose a sample clock rate five times faster than the
speed of the fastest signal being measured. A faster sample clock rate results in a
more accurate reconstructed waveform.
Displaying Waveforms
Waveforms are rarely displayed at an exact one sample point per pixel. Waveforms are usually displayed in a compressed or expanded format. As a general
rule, waveforms are compressed when the time per pixel is greater than the time
per sample clock. Waveforms are expanded when the time per pixel is less than
the time per sample clock.
For compressed DSO module waveforms, the display shows the lowest and
highest point that occupy a given pixel column joined by a vertical line. For
expanded waveforms, the display points between the actual sample points are
calculated.
For expanded DSO module waveforms, Sin(x)/x interpolation computes the
display points between the actual values acquired.
High-Speed Timing
The LA module provides high-speed timing support through MagniVu data. The
MagniVu data is stored in a separate memory that is parallel to the main
memory. All data from the sampler goes directly to the MagniVu memory. The
MagniVu memory also works like a circular buffer. Unlike the acquisition
memory, the MagniVu memory does not qualify data storage through the trigger
function block.
MagniVu data is continuously acquired on all channels at the fastest sample rate
of 500 ps. Like normal acquisition data, MagniVu data can be displayed in the
Listing or Waveform data windows. The MagniVu data is centered on the
LA module trigger in the data window. For additional information, see MagniVu
Data on page 3–62.
TLA 700 Series Logic Analyzer User Manual
2–15
Operating Basics
Detecting Glitches
One of the logic analyzer’s most useful features is its ability to detect and trigger
on signal glitches. A glitch is a signal that makes a transition through the
threshold voltage two or more times between successive sample clocks. Because
glitches are often signal transitions that occur intermittently, they can cause
circuit malfunctions that are extremely difficult to diagnose.
Although you could try using a very fast sample clock rate to ensure that you
never miss any glitches, a better solution is to use the glitch-detection feature.
The logic analyzer can trigger on a glitch, either alone or in combination with
other signal events. This capability is useful for catching intermittent glitches
that might not occur very often, or only when a particular operation is taking
place.
You can capture noise spikes and pulse ringing using the glitch capture feature.
Figures 2–16 and 2–17 show data captured by triggering on a glitch. In the
Waveform window, a glitch captured by an LA module is indicated by a band of
color. (See Figure 2–16. For clarity, an arrow identifies the glitch in the figure.)
You must select internal clocking to use the glitch detection feature.
Figure 2–16: LA module triggering on a glitch
2–16
TLA 700 Series Logic Analyzer User Manual
Operating Basics
Figure 2–17: DSO module triggering on a glitch
Performance Analysis Concepts
For performance analysis applications, you can use the Histogram window to
view the performance of your software. The actual data is displayed as horizontal
bars in a histogram.
You may want to use the Histogram window to see which one of your software
routines is taking up most of the CPU time. Or, you can use the Histogram
window to measure the amount of time used by a particular subroutine. You can
use a symbol file to view each of the routines by name.
Figure 2–18 shows an example of the Histogram window where the StopLite
routine is taking up most of the computer resources.
TLA 700 Series Logic Analyzer User Manual
2–17
Operating Basics
Figure 2–18: Viewing the performance of code with a Histogram window
Comparing Acquired Data Against Saved Data
You can use the LA module to compare acquired data against saved reference
data. Use the LA Setup menu to define the data channels that you want to use
during the compare operations. You can further define the number of samples
that you want to compare as well as data alignment offset.
In the Listing and Waveform windows, you can use color to quickly identify the
compared data. You can set up one color to show where the acquired data does
not equal the reference data. You can use another color to show where the
acquired data equals the reference data.
Figure 2–19 shows a Listing window during a memory compare operation;
notice that some of the data under the LA 2 A2 column appears in a different
color, indicating that there were differences between the acquired data and the
reference data.
2–18
TLA 700 Series Logic Analyzer User Manual
Operating Basics
Figure 2–19: Using color to show memory differences in a Listing window
Repetitive Acquisitions
Use the Repetitive acquisition features of the logic analyzer to automate
repetitive and time-consuming tasks. For example, you can specify the number
of times that you want the logic analyzer to acquire data. With each acquisition,
you can save the data to a file for analysis. You can also set up the logic analyzer
to open a file or execute a program when all of the acquisitions have been
completed.
You can set up the LA module to acquire and compare the acquisition data
against known reference data. The LA module can continue acquiring data until
there is a mismatch between the acquisition data and the reference data.
Figure 2–20 shows an example of such a setup where the acquired data is
exported to a file for each acquisition. When a data-mismatch occurs the logic
analyzer stops acquiring data and exports the data to a file. The faulty data can
now be analyzed by another application.
TLA 700 Series Logic Analyzer User Manual
2–19
Operating Basics
Figure 2–20: Defining repetitive setups
TLA 700 Programmatic Interface (TPI)
Using the TLA 700 Programmatic Interface (TPI) you can control a TLA 700
series logic analyzer from a separate user program from the logic analyzer itself
or from a remote computer. The interface is based on the Component Object
Model (COM). You can use any programming language or programming
environment that supports the Component Object Model, such as Microsoft
Visual C++ and Microsoft Visual Basic.
Using TPI, you can control various aspects of the logic analyzer. You can load
and save system and module setups. You can extract information from the logic
analyzer, such as LA module counter and timer values, configuration information, LA module data, and DSO module data for analysis by other applications.
The TLA 700 Programmatic Interface comes with its own online help (select
Help on TPI from the Help menu in the TLA application). For your convenience,
the information contained in the TPI help file is also available in Portable
Document Format (PDF) in the C:\Program Files\TLA 700\System directory.
The file name is tpi.pdf. You will need the Adobe Acrobat Reader application to
view or print tpi.pdf. If you do not have Adobe Acrobat Reader on your
machine, you can download a free copy from the Adobe site at http://www.adobe.com/acrobat/.
2–20
TLA 700 Series Logic Analyzer User Manual
Operating Basics
Symbol Support
Symbols simplify tasks, such as setting up triggers or identifying specific values
within the data. When you program a trigger or view data, it is cumbersome to
remember which numeric channel group values correspond to particular machine
instructions or code modules. The logic analyzer makes this task more manageable by allowing you to assign symbolic names or mnemonics to group values.
For example, you might assign the symbol WRITE to the control bus event that
causes the target system to write to a memory location. Then, if you wanted to
trigger when a write cycle occurs, you could enter WRITE in the trigger program
in place of the actual data value. You could also choose to have WRITE appear
in the Listing window for quick identification of the instruction.
In Figure 2–21, the example shows a trigger program which uses the symbol
SYSTEM_RESET as part of the trigger clause.
Figure 2–21: Using symbols in a trigger program
You can use symbol files with a Source window and an associated Listing
window to track the execution of source code. The symbol file provides the
information to associate a line of source code to an address in a Listing window.
When you move a cursor in one window, the symbol file provides the necessary
information to move the cursor to the correct location in the other window.
Often, the application software will define symbols for you. For example, when
you load a microprocessor support package, symbols are also loaded (typically,
to the control group). These symbols represent data values that correspond to bus
cycle types. Other software applications produce range symbol files which you
can load (typically, these files are loaded to the address group).
Symbol Files
To use symbols, you must first load or create one or more symbol files that
define the symbols. Symbol files contain symbol names and their associated data
values. You can use symbol files created by another application, edit symbol files
from other applications, or you can create your own symbol files using a text
editor.
TLA 700 Series Logic Analyzer User Manual
2–21
Operating Basics
Each entry in a symbol file consists of an alphanumeric symbol name with its
associated numeric value or range of values. After you create a symbol file, you
can specify the symbol file for the appropriate channel group in the Waveform or
Listing window, use symbolic names as a substitute for numeric values in the
Trigger and data windows, and use symbols for tracing source code in a Source
window.
Symbol files perform like look-up tables. For example, if the address of a printer
I/O port is at address F734BC, you can define a symbol, printer-port, that
corresponds to that value. Then, in the Trigger window, you can specify the
symbol name as an event in the trigger program and cause the module to trigger
when printer-port (F734BC) appears on the address bus. You can also specify the
symbolic display radix for the address channel group and the symbol name
printer-port will show in the Listing window every time F734BC appears on the
address bus.
Symbol Types. Two main types of symbol files are possible: pattern symbol files
and range symbol files. Range symbols can be further divided into three different
categories: functions, variables, and source code (source). Table 2–1 shows the
different types of symbols and the windows where they are commonly used.
Table 2–1: Using symbols in logic analyzer windows
Range symbols
Wi
Window
Pattern
a e symbols
y b l
Functions
Variables
Source code
Listing
Yes
Yes
Yes
Yes
Waveform
Yes
Yes
Yes
Yes
Histogram
No
Yes
Yes
No
Source
No
No
No
Yes
LA Trigger
Yes
Yes
Yes
Yes
Pattern Symbols. Pattern symbols consist of data patterns up to 32 bits. Each bit
in a pattern symbol can be 0, 1, or X (don’t care). Pattern symbols are used when
a group of signals define a logical state. For example, a microprocessor has a set
of pins that indicate the type of bus cycle in progress. A memory read cycle is
indicated when the RD~ and MREQ~ pins are 0 (logic low) and the BUSAK~
and M1~ pins are 1 (logic high). You can define a pattern symbol name called
mem-read that corresponds to bit pattern 1100 and thereby mark all memory read
bus cycles in the Listing window. For other bus cycles the logic state of these
pins is also important and you can define different bit patterns for each cycle
type.
2–22
TLA 700 Series Logic Analyzer User Manual
Operating Basics
Figure 2–22 shows pattern symbols used in a Waveform window.
Figure 2–22: Waveforms using pattern symbols
Range Symbols. Range symbols define a range of 32-bit addresses represented by
a contiguous set of integers, marked by specific lower and upper bounds. The
different types of range symbols are discussed in detail under TLA 700 Symbol
File Format beginning on page 0–1.
When defining a range symbol file, do not overlap ranges of values. If ranges
overlap, they may not be recognized. For example, if SYM1 covers the range
1000–3FFF, and SYM2 covers 2000–2FFF, then the values in range 2000–2FFF
may be recognized as either SYM1 or SYM2, and the values in the range
3000–3FFF may not be recognized as SYM1 at all.
The range symbols shown in Figure 2–23 define subroutine boundaries.
Figure 2–23: Listing data using range symbols
TLA 700 Series Logic Analyzer User Manual
2–23
Operating Basics
Symbols Dialog Box
Use the Symbols dialog box to provide an overview of all currently loaded
symbol files (see Figure 2–24). You can display information on all symbol files
currently used by the logic analyzer.
The following status information is available for each currently-loaded symbol
file:
H
The last time the file was loaded into the TLA 700 application software. It
also includes error and warning messages associated with the last load.
H
When the file was last modified. The logic analyzer also displays a message
if the file may need to be reloaded (such as when the file is modified after it
was first loaded).
H
The format of the loaded file.
H
If the file can be unloaded or if the file is currently in use. Symbol files can
only be unloaded if no data windows or setups are using them.
Figure 2–24: Symbols dialog box
2–24
TLA 700 Series Logic Analyzer User Manual
Operating Basics
The following content information is displayed in the Symbols dialog box:
H
Whether the file is a pattern symbol file or a range symbol file. If the file is a
range file, this field also lists the types of symbols loaded.
H
The number of symbols loaded from the file. Symbol files can have an
unlimited number of symbols. The number of symbols is limited by the
amount of memory. When you load a symbol file, the symbols are placed in
memory. Because symbol files consume memory, you should unload unused
symbol files to keep memory available for your main application.
H
The number of source files referenced by source code symbols loaded from
the file.
H
The minimum and maximum address values and offset information.
Click the Load button (see Figure 2–24) to open the Select Symbol File dialog
box and load a new symbol file. You can browse the file system for the symbol
file. If the symbol file is a range file, you can click the Options button in the
Select Symbol File dialog box to open the Load Symbols Options dialog box.
Click the Export button to save the current file as a TSF-format symbol file. You
can view the exported symbol file with applications such as Wordpad. Edit the
symbol file by saving it under a new name and using a text editor. Save the
edited file in text format. You can then load the edited symbol file.
Load Symbol Options
Dialog Box
Use the Load Symbols Options dialog box (see Figure 2–25) to specify options
for range symbol files before loading them into the system.
Figure 2–25: Load Symbol Options dialog box
TLA 700 Series Logic Analyzer User Manual
2–25
Operating Basics
Select one or more of the symbols types to load. If you want to use the symbol
file with the Source window, you should be sure to select Source Code symbols.
You can enter a decimal number for the maximum number of symbols to load.
The maximum number of symbols that you can load is limited only by the
amount of memory available. The file loads symbols until the specified
maximum number of symbols is reached. Additional symbols are ignored, even
if they fall within the Bound 1 and Bound 2 range limits.
The Bound 1 and Bound 2 fields define the range of symbol addresses that will
be loaded. You can enter any hexadecimal values from 0 through FFFFFFFF.
Symbols with values outside of these limits are ignored and will not be loaded.
NOTE. If the lower bound of the range symbol is within the Bound 1 and Bound 2
limits and the higher bound is not, the entire symbol will be valid. However, if
the higher bound is within the Bound 1 and Bound 2 limits and the lower bound
is not, the entire symbol will be ignored.
Select either Default Offset or Custom Offset to apply an offset to the symbol
values. If you select Default Offset, the default offset is read from the source file
and applied to each symbol in the file as it is loaded. If you select Custom
Offset, you can add or subtract the specified offset value to each symbol in the
file as it is loaded. You can choose any 32-bit hexadecimal value from 0 to
FFFFFFFF.
When you enter bound values, enter the values without an offset value. If your
application adds an offset, you must subtract the offset value before you enter the
bound values.
2–26
TLA 700 Series Logic Analyzer User Manual
Reference
Setup
This section describes how to set up the logic analyzer (LA) and DSO modules,
and how to load an LA module trigger program.
For further details, particularly about selections available to you in windows and
dialog boxes, please refer to the online help.
Starting From the System Window
The System window gives an overview of the logic analyzer configuration,
arming, and triggering relationships. The System window also indicates whether
LA modules are merged to increase the number of channels. See Figure 3–1.
A black arrow from one module to another indicates that one module is set up to
arm another. Figure 3–1 shows the merged LA module arming the DSO module.
A module that is programmed to cause a system trigger has an indicator symbol
on the right edge of the module graphic.
Arm indicator
System trigger indicator
Overlapped icons indicating
merged modules
Data source indicator
Figure 3–1: System window
TLA 700 Series Logic Analyzer User Manual
3–1
Setup
Opening Other Windows
from the System Window
You can use the System window as a quick navigation tool.
H
To open a module Setup or Trigger window from the System window, click
the Setup or Trigger button in the module icon.
H
To open a data window from the System window, click the data window
button. See Figure 3–2.
Figure 3–2: Opening a Waveform window from the System window
Disabling Modules
3–2
If you are not using a module, you can disable it by clicking the module’s On/Off
button. When you disable a module, make sure that no other trigger programs
depend on that module’s output.
Renaming Windows
You can rename the windows by selecting the current window labels and
overtyping. Names must be unique and are limited to the space available.
Identifying Modules
If you are unsure which physical module is represented by an icon, double-click
on the icon to open its System Properties page. This property page lists
information about the module, including the mainframe slot numbers in which it
is installed. (Slot numbers are indicated on the mainframe.)
TLA 700 Series Logic Analyzer User Manual
Setup
Setting Up the LA Module
The primary function of the Setup window is to configure the LA module for
compatibility with the target system. This is where you specify channel groups,
set thresholds, and select the sample clock rate. Additional selections configure
the LA module for best compatibility with the type of data you want to acquire.
Before you acquire and display data, you must first set up the LA module using
the LA Setup and Trigger windows. Together, these windows determine the data
to be acquired.
Each module has its own Setup window and Trigger window, each is set up
individually. Generally, you should configure the Setup window before the
Trigger window, because some of the Setup window settings affect Trigger
window selections.
H
To open the LA module Setup window, go to the System window and click
the LA module Setup button.
Figure 3–3: The LA module Setup window
NOTE. If you intend to use merged modules, turn to page 3–34 for information
before you proceed with the setup procedure.
TLA 700 Series Logic Analyzer User Manual
3–3
Setup
Microprocessor Support
Setup
If you intend to use a microprocessor support package, load it before completing
the entries in the Setup window. The microprocessor support package configures
the Setup window for you.
H
To load a microprocessor support package, go to the File menu, click Load
Support Package, select the support package you want to load, and then click
Load.
After loading the microprocessor support package, the LA Setup window shows
the channel definitions, channel groups, and clocking requirements for the
microprocessor support package. Figure 3–4 shows an example of the LA Setup
window after loading the QSTART support package.
Figure 3–4: Setup window with the QSTART support package
For information about microprocessor support packages, refer to the online help
and to the instruction manual that came with your microprocessor support
package.
Performance Analysis
Setups
Memory Compare
3–4
If you intend to do performance analysis with your LA module, you need to
define the channel and clocking setups in the Setup window. You may also want
to load a microprocessor support package which contains the predefined channel
setups and clocking setups.
Memory Compare allows you to compare the current acquisition data of an LA
module against a known reference data. You can quickly view data differences
and similarities in a Listing or Waveform window using user-defined colors.
TLA 700 Series Logic Analyzer User Manual
Setup
Selecting Channels for the Memory Compare. Choose the channels that you want
to compare in the LA Setup window by selecting Channel Compare in the Table
Shows box (see Figure 3–5). You can then compare all data channels, specific
channel groups, or individual channels by selecting the appropriate channels in
the Probe Channels/Names table.
Figure 3–5: Selecting channels for memory compare
After selecting the channels that you want to compare, click the Define Compare
button in the lower-right corner of the Setup window to define the compare
actions.
TLA 700 Series Logic Analyzer User Manual
3–5
Setup
Defining Memory Compare Parameters. Select Enable Data Compare in the
Compare Definition dialog box as shown in Figure 3–6. Select the reference data
source in the box; if the data source that you are interested in does not appear in
the list, click Add Data Source to browse for the data source in the file system.
Figure 3–6: Enabling data compare
After you select the data source, define the amount of data that you want to
compare against. You can compare all data or a portion of the data by filling in
the appropriate information. You can also define the alignment of the data by
filling in the appropriate information. A summary of your setup displays at the
bottom of the dialog.
NOTE. After defining the compare setup, remember to select Show Compare in
the Listing Window or Waveform Window property page
Guidelines for Memory Compare. There are a few guidelines that you should be
aware of when using memory compare:
3–6
H
You must enable the memory compare in the Compare Definition dialog box
(see Figure 3–6).
H
Acquisition modules and reference modules must be the same width.
H
Specify the color of compare data in the Listing Window or Waveform
Window property sheet, or use the default colors.
H
You can search for data differences or data equalities.
TLA 700 Series Logic Analyzer User Manual
Setup
H
You can use memory compare with repetitive acquisitions.
H
You can compare only the main LA data, you cannot compare glitch data,
disassembler group data, or MagniVu data.
NOTE. Although you cannot compare disassembler group data directly, you can
compare the raw nondisassembled data by using the channel groups as defined
in the Setup window. To view these channel groups in a Listing window, use the
Add Column toolbar button to add the channel group to the window.
Clocking
Use Clocking to specify the clock(s) used to sample data. Select one of two basic
clocking modes, Internal (asynchronous) or External (synchronous). A third
choice, Custom, is available if a microprocessor support package has been
loaded. Your clocking choice determines further clocking selections.
Internal Clocking. Internal (asynchronous) clocking uses the LA module’s internal
clock to determine when to sample data. Typically, internal clocking is used for
timing analysis (waveform data).
When you select Internal clocking, the only additional selection to make is the
clock rate in the next field.
Because the internal clock signal is asynchronous to the target system, be careful
to select a sample period that is considerably faster than the data rate of your
target system.
External Clocking. External (synchronous) clocking synchronizes data sampling
with the clock of the target system so you can be more selective about the data
you sample. This type of clocking is best for software analysis (listing data).
When you select External clocking, you have the option of further selections to
define the sample clock. You can create clocking equations in the Clocking
dialog box. Clocking equations qualify when data is sampled. The equations
consist of a Boolean combination of events, linking clock and qualifier lines.
Data is sampled and stored in memory only when this clock equation is true.
TLA 700 Series Logic Analyzer User Manual
3–7
Setup
Advanced Clocking. Advanced clocking is available only if you select External
clocking. Use advanced clocking to set up multiple-phase clocking, probe
demultiplexing, and other clocking controls. Multiple-phase clocking specifies
two different sample clock equations and assigns an equation to separate probe
groups to clock in sample data. You can also sample data from different channel
groups at different points in time relative to the sample clock through a variable
setup and hold window.
Custom Clocking. Custom clocking is used only with microprocessor support
packages. Custom clocking enables and disables a variety of microprocessor-specific clock cycle types (such as DMA cycles).
For more information, see the instructions that came with your microprocessor
support package.
Selecting the Acquisition
Mode
Use Acquire to select the acquisition mode. The acquisition mode determines the
data to store. You can store channel data only, glitch data, or blocks of data
around requested samples.
Normal Mode. Normal mode stores only the requested channel data.
Blocks Mode. Blocks mode stores a block of approximately 60 samples around
each qualified sample. In Blocks mode, only channel data is stored. If you store
blocks they will override other forms of data qualification. All samples in the
block are always stored.
Glitch Mode (Internal Clocking Mode Only). Glitch mode captures glitch data and
regular data for each data channel. You must select internal clocking for Glitch
mode to be available.
Glitch mode limits memory depth to half of the maximum depth and limits the
sample period to 10 ns or greater.
3–8
TLA 700 Series Logic Analyzer User Manual
Setup
Setting Memory Depth
Use Memory Depth to specify the total number of samples acquired by the LA
module. If you do not require full memory depth, select a lesser value because
you will have less data to search to find the data of interest.
For a given memory depth there is a tradeoff between the clock sample rate and
data record length. (A faster sample rate provides a shorter time window, but
with higher resolution.)
NOTE. If you select Glitch mode, the maximum memory depth is limited to one
half the normal value.
Channel Grouping
Use channel grouping to organize the LA probe channels to match the configuration of the target system. Depending on your application, match the channel
groups to the address and data buses, or other channels of interest. Then name
the channel groups for easy identification.
Any number of groups can be created. Each group can contain any combination
of module channels; the application does not restrict you from repeating channels
from various groups.
When using group range events (range recognizers), the probe groups and probe
channels must be used in hardware order. That is, probes must be used from the
most-significant probe group to the least-significant probe group based on the
following order:
C3 C2 C1 C0 E3 E2 E1 E0 A3 A2 D3 D2 A1 A0 D1 D0 Q3 Q2 Q1 Q0 CK3
CK2 CK1 CK0
The probe channels must be used from the most-significant channel to the
least-significant probe channel based on the following order:
76543210
If a microprocessor support package is loaded, the channel groups are defined for
you.
TLA 700 Series Logic Analyzer User Manual
3–9
Setup
NOTE. If a microprocessor support package is loaded, you should not change or
delete the default channel groups. Doing so can cause an inaccurate analysis.
You can still add and delete new channel groups.
Channel groups defined in the channel grouping table are used in other displays
and setup controls. The order of the groups in this table determines the order of
presentation in other parts of the application.
Figure 3–7: Channel grouping table in the Setup window
Channel Group Name. Each channel group must have a name. You can use the
default name, or you can enter another name, as long as it is unique within the
module. There is no limit to the number of groups you can create.
For each group name, you must list all the probe channels that make up the
group. The group names are listed in the left column of the table. The individual
probe channels that make up each group are listed in the right column of the
table. The center column of the table lists the number of channels in a group
(where a zero refers to bit 0). For example in Figure 3–7, the Address group is
made up of 32 channels, with channel 31 as the most-significant bit (A3-7) and
channel 0 as the least-significant bit (A0-0).
Probe Channels/Names Table. Use the Probe Channels/Names Table to enter
names for individual channels, add and remove channels from a group, or change
polarity of individual channels.
3–10
TLA 700 Series Logic Analyzer User Manual
Setup
Activity Indicators
Use the Activity Indicators dialog box to show the real-time signal activity at the
LA module probe tip without having to acquire data. The activity symbols
indicate whether the signals at the probe tip are high, low, or changing. See
Figure 3–8.
H
In the LA Setup window, click Show Activity.
Figure 3–8: The Activity Indicators dialog box
If the activity indicators show no activity, the problem could be that there is no
signal voltage, an incorrect threshold voltage level, or the channel lead is not
connected. If all the channels associated with a probe are inactive, check the
probe connections to the LA module.
You can leave the Activity Indicators dialog box open while you set up other
windows, such as setting up the Trigger window or adding channels to the
Waveform or Listing window. This dialog box is useful for verifying that clocks
are active in external clocking and for troubleshooting complex clock setups.
TLA 700 Series Logic Analyzer User Manual
3–11
Setup
Setting Probe Thresholds
Use Set Thresholds to set the input threshold voltage settings for probe channels,
clocks, and qualifiers of the LA module. Changes are immediately executed even
during acquisition. Figure 3–9 shows the Set Thresholds dialog box.
Initially, the Probe Thresholds box contains values that are set in the Preset page
of the Options Property sheet.
Figure 3–9: Probe Thresholds dialog box
Setting Up the Trigger Program
The primary function of the LA Trigger window (see Figure 3–10) is to construct
a trigger program. You also use the Trigger window to select how and when to
store data.
A trigger program is a series of events and actions that define when to trigger
and store data. The trigger program filters acquired data to find a specific data
event, or series of data events. The trigger program can accept information from
other modules or send signals external to the logic analyzer.
3–12
TLA 700 Series Logic Analyzer User Manual
Setup
Trigger programs range from the simple to the extremely complex. They are the
key to logic analyzer operation, which is to acquire the desired data in acquisition memory and to display the data for viewing. One method for setting up a
trigger program is to load a trigger program from the trigger library. You can
then alter the trigger program details as necessary. Once you become familiar
with trigger programming, you can also create trigger programs without the help
of the trigger library. For more information, see Trigger Library on page 3–16.
Before you work in the Trigger window, you should already have configured the
LA module Setup window because some of the Setup window settings affect
Trigger window selections.
Figure 3–10 shows a Trigger window with a trigger program loaded from the
trigger library.
Figure 3–10: LA module Trigger window
Trigger Program Structure
A trigger program is made up of one or more states (up to 16). Only one state is
active at a time.
Each state is made up of one or more clauses. If you use more than four trigger
event resources in a state, you can have up to four clauses per state. If you have
four or fewer trigger event resources in a state, you can define up to 16 clauses
per state. Clauses are made up of two parts: an If statement, that defines the data
event of interest, and the Then statement, which specifies the action taken when
the If statement is true. You can define up to eight events per If statement and up
to eight trigger actions per Then statement.
TLA 700 Series Logic Analyzer User Manual
3–13
Setup
During each sample clock cycle, all clauses within the active state simultaneously evaluate each data sample. Clauses are evaluated from top (State #1, IF-Then
Clause #1) to bottom. When one of the clauses goes true (the event defined in the
If statement occurs), then the logic analyzer performs the action(s) specified in
the Then statement. There are several actions to choose from, including
triggering the system and transferring control of the trigger program to another
state.
NOTE. If multiple clauses are true in the same clock cycle, only the earliest
clause in the sequence to go true will have its action(s) executed.
Trigger Window Structure
The Trigger window summarizes the trigger program. The Overview shows the
general structure of the trigger program. The Trigger Detail, at the right of the
window, summarizes activity within individual program states. You can click the
If/Then button in the Trigger Detail to open the Clause Definition dialog box,
which is where the actual trigger programming takes place.
Overview
Trigger Detail
Figure 3–11: Trigger window structure
3–14
TLA 700 Series Logic Analyzer User Manual
Setup
Overview. The Overview portion of the Trigger window shows the relationship of
the states. See Figure 3–12. This example shows a branch occurring in State 2.
This example also shows that a trigger (note the trigger indicator) occurs in
State 2 and an Arm occurs.
To view the details in a particular state, double-click on the State button in the
Overview.
Figure 3–12: Overview portion of LA Trigger window
You can view the progress of the trigger states during acquisition using the
Status Monitor. (See Status Monitor on page 3–43.)
Trigger Detail. The Trigger Detail portion, at the right of the Trigger window,
shows summary information about the clauses within the states. See Figure 3–13. For lengthy trigger programs, click on the State buttons in the
Overview to jump to the corresponding Trigger Details.
Figure 3–13: Trigger detail portion of LA Trigger window
TLA 700 Series Logic Analyzer User Manual
3–15
Setup
Click on the If/Then button to open the Clause Definition dialog box for
complete information about the clause.
Trigger Library
One advantage of a logic analyzer is that you can create sophisticated trigger
programs so that you can carefully qualify and store only the relevant data.
However, configuring such trigger programs can be time-consuming.
The TLA 700 Series Logic Analyzer simplifies this process with its trigger
library. It provides a list of trigger programs to fit most needs. The trigger
programming is partially done for you.
To use the trigger library, select a trigger program that is close to what you
require, and then alter the program as necessary. Once you have customized the
trigger, you can save it along with the rest of your setup using the Save Module
or Save System function. You can later retrieve the saved trigger program alone
or with the related saved module or system information.
Table 3–1 lists the programs in the trigger library and a brief description of each
library item.
Table 3–1: LA Trigger library
3–16
File name
Description
TrigOnA
Trigger on the first occurrence of Event A.
TrigOnAafterN
Wait for Event A. Trigger after the specified number of
events.
TrigOnNthA
Trigger after Event A has occurred a specified number of
times.
TrigOnNthAorB
Trigger after Event A or Event B has occurred a specified
number of times.
TrigOnAthenB
Trigger if Event B eventually follows Event A
TrigOnAimedB
Trigger if Event B immediately follows Event A.
TrigOnAthenBresetC
Wait for Event A. If Event C occurs before Event B, then
reset and wait for Event A again. Otherwise, trigger when
Event B occurs.
TrigOnAtoBltNCs
Trigger on Event C if Event C occurs less than or equal to
the specified number of times between Event A and
Event B.
TrigOnAtoBgtNCs
Trigger on Event C if Event C occurs more than the
specified number of times between Event A and Event B.
TrigOnAthenBinN
Trigger when Event B occurs within a specified number of
events of Event A.
TLA 700 Series Logic Analyzer User Manual
Setup
Table 3–1: LA Trigger library (Cont.)
File name
Description
TrigOnAinRange
Trigger when the group event occurs within specified
upper and lower ranges.
TrigOnGlitch
Trigger on glitches; valid only with Internal clocking.
TrigOnSetHold
Trigger on setup and hold violations; valid only with
External or Custom clocking.
TrigOnAtoBinT
Trigger when Event B follows Event A within the specified
time.
TrigOnAtoBafterT
Trigger when Event B follows Event A after the specified
time.
CountA
Count the occurrences of Event A. This program does not
trigger the LA module.
CountAorB
Count the occurrences of Event A or Event B. This
program does not trigger the LA module.
CountCfromAtoB
Count the occurrences of Event C between Event A and
Event B. This program does not trigger the LA module.
AccumCfromAtoB
Accumulate the total counts of Event C between Event A
and Event B. This program does not trigger the LA
module.
AccumTfromAtoB
Accumulate the total time between Event A and Event B.
This program does not trigger the LA module.
AccumTinRange
Accumulate the total time spent within the specified range
in Event A. This program does not trigger the LA.
AccumToutRange
Accumulate the total time spent outside the specified
range in Event A. This program does not trigger the LA.
TimeBetweenAandB
Measure the delay between Event A and Event B. This
program does not trigger the LA module.
TimeInRange
Measure the time spent within a specific range of events.
This program does not trigger the LA module.
TimeOutRange
Measure the time spent outside a specific range of events.
This program does not trigger the LA module.
StoreOnA
Store nothing except occurrences of Event A. This
program does not trigger the LA module.
StoreOnAorB
Store nothing except occurrences of Event A or Event B.
This program does not trigger the LA module.
StoreFromAtoB
Store nothing except the samples between Event A and
Event B. This program does not trigger the LA module.
TLA 700 Series Logic Analyzer User Manual
3–17
Setup
Table 3–1: LA Trigger library (Cont.)
Loading a Trigger from the
Trigger Library
File name
Description
StoreExceptAtoB
Store everything except those samples between Event A
and Event B. This program does not trigger the LA
module.
StoreInRange
Store nothing except samples within specified ranges of
Event A. This program does not trigger the LA module.
TrigOnSignal
Trigger the LA module on a signal from another module.
SendSignal
Send a signal to another module when Event A occurs.
TrigSysOnA
Trigger the system when Event A occurs.
To load a trigger program from the trigger library, follow these steps:
1. From the Trigger window, click the Load Trigger toolbar button.
2. From the Load LA Trigger dialog box, click Browse Library.
3. Select a trigger program from the list.
4. Click Open to apply the selection.
5. Click Load to load the trigger program into the module.
Once you load the trigger program, customize it for your application.
6. Click the If/Then button to open the Clause Definition dialog box. This is
where you specify trigger program details.
7. Change the Clause Definition selections to fit your application. Start with the
first box in the If statement; the selection you make affects other selections.
Enter appropriate values in the address and data boxes.
3–18
TLA 700 Series Logic Analyzer User Manual
Setup
8. If you want additional clauses, you can add to the If or Then statements
using the Add button, as shown in the following figure.
9. Click OK to complete the clause definition.
10. Check the trigger program summary in the Trigger window.
TLA 700 Series Logic Analyzer User Manual
3–19
Setup
Trigger Events
Use trigger events to define the If portion of the event clause in the trigger
program. Table 3–2 lists the trigger events available.
Table 3–2: Trigger events
Trigger Resources
3–20
Event
Description
Word
Tests the channel groups for the word values defined in
the Word definition dialog box.
Group
Tests a specified channel group for a specific value, a
range of values, or a value change.
Channel
Tests the specified channel for a value or a value change.
Glitch
Detects glitches in channel groups as defined in the Glitch
Detect dialog box. Only available with internal (asynchronous) clocking.
Setup & Hold fault
Tests setup and hold parameters as defined in the Setup
and Hold Event dialog box. Not available as an event with
internal (asynchronous) clocking.
Counter and timer events
Tests the specified counter or timer value. Timer events
are only supported by LA Modules with serial numbers
B020000 or higher.
Signal
Looks for one of the four internal system signals. Only one
signal event is available in a trigger program.
Anything
All sampled data makes this event true.
Nothing
All sampled data makes this event false.
You can use up to 16 unique trigger resources (not including counters and timers)
in a trigger program to define the events and actions. A trigger resource can be
used more than once in a trigger program. However, some events use more than
one trigger resource. Table 3–3 lists the trigger resources and any interactions
that may occur when you use them.
TLA 700 Series Logic Analyzer User Manual
Setup
Table 3–3: Trigger resources
Resource
Operator
Interactions and restrictions
Word
=, Is Not
One trigger resource across all defined
channel groups.
Word recognizer
=, Is Not
One trigger resource per channel
group.
Range recognizer
<, <=, >=, >, Is In,
Is Not In
Three trigger resources per channel
group.
Change detector
Changes
One trigger resource per group event,
one change detector allowed in a
trigger program, not available when
transitional storage is used.
Word recognizer
=
One trigger resource per channel
group.
Change detector
Goes, Doesn’t go
One trigger resource, one change
detector allowed in a trigger program,
not available when transitional storage
is used.
Group
Channel
Glitch
One trigger resource, only available
with internal (asynchronous) clocking.
Setup & Hold Fault
One trigger resource, only available
with external (synchronous) or custom
clocking.
Counter
>, <=
0 trigger resources, 2 counters or
2 timers.
Maximum width
51 bits
Maximum clocking
250 MHz
Maximum count
251
Counter 1 and 2 events conflict with
Timer 1 and 2 events respectively.
Timer
>, <=
0 trigger resources, 2 counters or
2 timers
Maximum width
51 bits
Maximum clocking
250 MHz
Maximum time
2,000,000 S
(23 days)
Counter 1 and 2 events conflict with
Timer 1 and 2 events respectively.
TLA 700 Series Logic Analyzer User Manual
3–21
Setup
Table 3–3: Trigger resources (Cont.)
Trigger Actions
Resource
Operator
Interactions and restrictions
Signal (Signal in)
Is True, Is False
One trigger resource, uses one of four
system signals. Only one signal event
is available in a trigger program.
Anything
0 trigger resources. Used as a placeholder. Not available with the OR
conjunction.
Nothing
0 trigger resources. Used as a placeholder with the OR conjunction.
After defining the events in the If (event) portion of the clause, you can select
one or more trigger actions to complete the clause. Table 3–4 lists the trigger
actions available for your trigger program.
Table 3–4: Trigger actions
3–22
Action
Description
Trigger
Triggers the current module. When you use Trigger in the
trigger program, you cannot use Trigger All Modules.
Trigger All Modules
Also known as a System trigger. This signal is also
available at the System Trigger Out connector. When you
use Trigger All Modules in the trigger program, you cannot
use Trigger.
Go To
Passes the program flow to a different trigger state. You
can only use one Go To action in the clause definition.
Counter and Timer actions
Starts, stops, resets, or clears counters or timers.
Counter 1 and 2 actions conflict with Timer 1 and 2
actions respectively. Counter/timer actions may conflict
with counter/timer event usage.
Set and Clear Signal
Sets or clears one of the four internal system signals. You
can use only one Set or Clear in a trigger program. The
Set or Clear Signal is mutually exclusive with the Arm
Module action.
Arm Module
Sends an Arm signal to another module. The other
module begins running its trigger program. You can arm
only one module in a trigger program. However, you can
use actions throughout the trigger program. Arm Module
is mutually exclusive with Set and Clear Signal actions.
Store Sample
Stores exactly one sample. Not available in Start/Stop
storage mode.
TLA 700 Series Logic Analyzer User Manual
Setup
Table 3–4: Trigger actions (Cont.)
Other Trigger Options
Action
Description
Start & Stop Storing
Begins or ends storing of samples. Start and Stop Storing
actions only appear when you select Start/Stop storage
mode. Use Start and Stop Storing in conjunction with
Start/Stop storage mode in the Trigger window. Available
only in Start/Stop storage mode.
Do Nothing
Use as a placeholder when defining a complicated trigger
program. Does not override other actions specified in a
clause.
From the Trigger window, you can also make data storage and trigger position
selections.
Storage. Use the storage selections to avoid filling up the acquisition memory
with data samples that do not interest you. You can use the storage selections to
disqualify the unwanted data samples and fill memory only with the desired data.
Use the Storage box to select the default data storage rules for the module. Use
one of the storage actions in the Then statement of the clause definition to
override the default storage setting.
The example shown in Figure 3–14 is using conditional storage. Data is stored
only when the specified event is true.
Figure 3–14: Using trigger storage
TLA 700 Series Logic Analyzer User Manual
3–23
Setup
Trigger Position. The Trigger Position selects the amount of posttrigger data that
is stored and determines the position of the trigger in the data record.
After a module has triggered, it continues to acquire data until it fills a specified
amount of memory. The total memory depth that the module fills is set in the
Memory Depth box in the Setup window. The proportion of data that is stored
before and after the trigger is determined by the Trigger Position field. For
example, if the Trigger Position is set to 10%, and the module triggers, then the
module continues to acquire posttrigger data until the remaining 90% of memory
is filled.
If the trigger event occurs on any data sample before the specified amount of
pretrigger data has occurred, then the logic analyzer triggers and begins filling
memory with posttrigger data regardless of the amount of pretrigger data
specified. For example, if you set the trigger position to 50% and set the logic
anlayzer to trigger on a processor reset, start the logic analyzer, then power on
your target system, the logic analyzer will trigger. However, the logic analyzer
memory will be filled only with posttrigger data, not any pretrigger data. This is
due to the trigger event, which has higher precedence, occurring before the
pretrigger condition is satisfied.
Saving Trigger Programs
You can save your trigger programs for future use by means of the Save Module
or Save System functions. Although these functions save more than just the
trigger program, you can load just the trigger program from one of the saved
files. For more information, see Saving and Loading Setups, Triggers, and Data
on page 3–35.
Setting Up the DSO Module
Before acquiring and displaying an analog waveform, you must first set up the
DSO using the DSO Setup window. You can set the vertical, horizontal, and
trigger parameters manually, or you can use Autoset for a quick automatic setup
based on the input signal.
NOTE. The setup and data windows operate independently; you cannot change
setup parameters by changing the data display. Once you acquire data, you can
manipulate the display, but that will not change the input settings used to
acquire the data. You must return to the DSO Setup window to change input
settings which take effect with the next acquisition.
H
3–24
To open the DSO Setup window, go to the System window and click the
DSO Setup button.
TLA 700 Series Logic Analyzer User Manual
Setup
Figure 3–15: DSO Setup window
DSO Probe Calibration
Probe calibration optimizes the signal path for this probe/channel/module
combination. For maximum accuracy, execute Probe Cal if any of these
conditions have occurred:
H
The ambient temperature has changed more than 5°C
H
You reconnect the probes to different DSO module input channels
The Probe Calibration dialog controls all DSO probe calibration cycles and
directs you to perform any necessary steps. You can calibrate all attached probes
or only the probe on the selected channel.
NOTE. Passive or unknown probes are not calibrated.
You can start a calibration cycle, view the progress of calibration, and see the
results of calibration. Once calibration starts, the calibration cycle of a single
probe cannot be stopped. After a calibration cycle completes, you can see the
status of probe calibration.
H
To open the Probe Calibration dialog, go to the System window and click the
DSO Setup button, select a vertical tab (Channel x), and click Probe Cal.
TLA 700 Series Logic Analyzer User Manual
3–25
Setup
NOTE. You should execute the DSO module self calibration if the ambient
operating temperature has changed more than 5_C since last calibration. Also,
you should execute the self calibration once a week if vertical settings of 50 mV
full scale or less are used. Perform self calibration after a 30 minute warm up.
To open the Self Calibration property page, go to the System menu and select
Calibration and Diagnostics. Click Self Calibration.
Autoset
Use Autoset when you need to see a signal in a circuit, but do not know the
signal amplitude or frequency. Autoset automatically chooses the DSO setup
values based on the input signal at the time you clicked the Autoset button.
Autoset works best on repetitive signals that do not have a DC offset component.
If the Autoset setup does not display the waveform as you want it, you can easily
change the setup manually.
To set the DSO input values based on the input signal:
1. Go to the System window and click the DSO Setup button.
2. Click Autoset from any page of the DSO Setup window.
The Autoset selections apply to all input channels, the horizontal setup, and
the trigger setup, regardless of which Autoset button was clicked.
3. If the signal changes, or you move the probe to another signal, click Autoset
again to reset the setup values.
Autoset affects only the DSO setup; it does not affect data window settings. You
may need to adjust data window settings for optimum display of the data.
Vertical Controls
Use the vertical controls to adjust vertical input voltage parameters. See
Figure 3–16.
H
3–26
To open the page containing the vertical controls, go to the System window
and click the DSO Setup button and then select one of the Channel tabs.
TLA 700 Series Logic Analyzer User Manual
Setup
Figure 3–16: DSO Setup window vertical input settings
For best vertical resolution, set the range just slightly larger than the expected
input signal. Autoset automatically sets the vertical range for the signal,
assuming a 0 VDC offset.
Offset. Offset is the offset voltage applied to the probe. If Range is changed using
the preset values, then Range also sets the Offset. The Offset default is 3 V for
TTL signals.
Bandwidth. Bandwidth is the range of frequencies that can be acquired and
displayed accurately. Your bandwidth selection sets the upper limit of frequencies that will be acquired and displayed. Bandwidth filters reduce unwanted
noise and aliasing.
Coupling. Coupling selects how the input signal is coupled to the vertical input
channel.
TLA 700 Series Logic Analyzer User Manual
3–27
Setup
Horizontal Controls
Horizontal settings control the rate at which the data is sampled and the amount
of data acquired. See Figure 3–17.
H
To open the horizontal page, go to the System window, click the DSO Setup
button, and then select the Horizontal tab.
Figure 3–17: DSO Setup window Horizontal settings
Sample Period. The Sample Period sets the interval between successive samples
in a waveform record. Choose a sample period that is fast enough that the
waveform will not be aliased, and slow enough to provide the waveform record
length that you need. For repetitive waveforms, you should set the sample period
to at least 5 faster than that of the waveform. (Sample period ≤ 15@ waveform
period.)
Memory Depth. The Memory Depth sets the total number of data samples to be
acquired. If you do not need to use the full memory depth to acquire the data of
interest, select a smaller memory depth to get faster acquisitions.
Trigger
The DSO Trigger page contains all controls for setting DSO trigger events and
actions. Threshold changes are recognized and executed immediately during
acquisitions. Execution of all other controls are delayed until the next acquisition.
H
To open the Trigger setup page, go to the System window and click the DSO
Trigger button.
Select a trigger event from the list of event types, and then modify it for your
application.
3–28
TLA 700 Series Logic Analyzer User Manual
Setup
Event Type. Event Type selects the type of event the DSO will recognize as a
trigger. Choose from the list of trigger event types. The following figure shows
two of the available trigger event selections.
Mode. Mode selects whether the DSO waits for a trigger (Normal) or forces a
trigger after a set length of time has passed without a trigger (Auto).
Action. Action selects what happens when a trigger is recognized. Choose from a
list of actions. Actions include triggering the DSO, triggering all modules, or
triggering and arming another module.
TLA 700 Series Logic Analyzer User Manual
3–29
Setup
Trigger Position. Trigger position sets the amount of data in the data record that
occurs before the trigger.
H
To set the Trigger Position, use the slider or enter a numeric value, as shown
below.
Event-Based Selections. Depending on the trigger event you choose, other
selections may become available. Refer to the online help for further information.
System Trigger
The system trigger is a global trigger event that forces all untriggered modules to
arm immediately and trigger. Only one system trigger occurs per acquisition.
When displaying data, the logic analyzer uses the system trigger as the primary
reference point for the acquisition. The data windows show the system trigger
and all module triggers. Module triggers can be forced by the system trigger or
specified by module trigger programs.
The system trigger can be generated from any of several sources. Often, the
system trigger is specified in a module’s trigger program. Any module can
specify the system trigger as a trigger action (Trigger All Modules). However,
modules can specify trigger actions other than system triggers, and the system
trigger does not have to originate from a module. The logic analyzer can also
accept a system trigger generated by an external source. External system triggers
are input through the SYSTEM TRIG IN connector. Regardless of the source of
the system trigger, all modules must respond.
It is not uncommon to have a condition where the acquisition completed, but
where an explicit system trigger did not occur. (This means that there was neither
an external system trigger, nor a system trigger generated internally by a module
trigger program.) To ensure that a time reference exists for the acquisition, the
logic analyzer must designate a system trigger. If no system trigger is generated
during an acquisition (the modules are internally triggered), the logic analyzer
designates the latest-occurring module trigger as the system trigger.
3–30
TLA 700 Series Logic Analyzer User Manual
Setup
NOTE. If an acquisition does not complete, due to one or more modules not
receiving a trigger or not completing posttrigger acquisition, then you can
manually stop the acquisition by clicking the Stop button. Clicking the Stop
button effectively generates a system trigger and completes the acquisition.
The system trigger is a latched event and it resets to a false state between
acquisitions. The external system trigger input uses real-time gating and is only
active (capable of latching system triggers) during the actual acquisition period.
The logic analyzer can also send an internally-generated system trigger out to the
target system or to other test equipment through the SYSTEM TRIG OUT
connector. All the external signal inputs and outputs operate at TTL levels. The
connectors are located at the rear of the portable mainframe and at the front of
the benchtop mainframe. For more information about external signaling
capabilities, see Intermodule and External Signaling on page 3–32.
Arming Modules
Using the arm feature, you can use one module to control when another module
accepts triggers. When module A arms module B, this means that module B does
not begin looking for a trigger until it receives an arm signal.
Arming is accomplished through trigger actions. For the LA module, arming is
specified in the Clause Definition dialog box; for the DSO module, arming is
specified in the Trigger page. A module can arm any one of the other modules.
The designated module can be armed by only one module. The same arming
action can, however, appear multiple times within the same trigger program.
Arms are latched events which, once set, cannot be cleared until the acquisition
is completed.
NOTE. For a single module, arming and internal signaling are mutually
exclusive. You cannot simultaneously arm modules and set signals. You can test
for a set signal (for example, If Signal X Is True), but you must designate an
external signal for this purpose; otherwise you will be unable to set the signal
when using the arming feature.
TLA 700 Series Logic Analyzer User Manual
3–31
Setup
Intermodule and External Signaling
The logic analyzer has four internal signals that you can use to set up trigger
conditions between modules, or to send or receive signals external to the logic
analyzer. Use the Signals property page, shown in Figure 3–18, in conjunction
with the module trigger programs to configure these signals for your application.
The trigger programs determine when the signals occur. The Signals property
page specifies characteristics of the signals.
NOTE. Be careful to observe the bandwidth and latency specifications when
using internal and external signals. Refer to Tables 3–15 and 3–16 on pages A–3
and A–5 for information.
H
To open the Signals property page, go to the System menu and click System
Configuration. Then select the Signals tab.
Figure 3–18: Signals property page
Internal Signals
3–32
All LA modules can set and clear any of the four internal signals. The DSO can
set but not clear any signal. The logical output of these signals can be used as an
event in other modules’ trigger programs. You can also connect the internal
signals to the External Signal In and External Signal Out connectors on the
mainframe, so that you can use an external signal as a trigger event or send a
signal out when a trigger condition is met.
TLA 700 Series Logic Analyzer User Manual
Setup
Internal signaling is for users with special trigger programming requirements.
Internal signaling adds flexibility to trigger programming, but also adds
complexity. When using internal signaling you must take care that the signals are
correctly set and cleared, and that the trigger programs for all modules are
compatible with regard to signal usage. Also, you must have correctly set the
internal signal attributes in the Signals property page.
Internal signaling is accomplished through trigger actions specified in the Clause
Definition dialog box and the DSO Trigger page.
NOTE. Arming and internal signaling are mutually exclusive. You cannot
simultaneously arm modules and set signals. You can test for a set signal (for
example, If Signal X Is True), but unless you have designated an external signal
for this purpose, you will be unable to set the signal when using the arming
feature.
Signal Logic Function. To use internal signals, you must select which internal
signal logic function is appropriate for your trigger program. Signals 1 and 2
(high speed) can be asserted by only one module each. For signals 3 and 4, the
modules can be wired-OR or wired-AND. Selecting the OR function means that
any module can assert the signal. Selecting AND means that all modules must
set the signal for it to be asserted. The same logic applies to clearing signals.
The logic function applies only at a module level, not to multiple set/clear
statements within a single module.
NOTE. Be careful when using wired-AND internal signals. If your trigger
depends on an internal signal, all modules must set the signal for it to be
asserted, or the trigger will not occur. If you change your trigger program,
remember to update the logic function settings accordingly.
External Signals
The logic analyzer can send and receive signals to/from the target system using
the External Signal In and External Signal Out connectors on the mainframe. Use
the External Signal In function to include a signal from your target system as
part of the trigger setup. Use the External Signal Out function to send a signal to
the target system or other test equipment when a trigger condition is met.
The connection from the module to the external connector is made by one of the
four internal signals. You must designate which internal signal is to be used for
this purpose.
TLA 700 Series Logic Analyzer User Manual
3–33
Setup
The external signal connectors are located at the rear of the portable mainframe
and at the front of the benchtop mainframe. The external signals all operate at
TTL logic levels.
Merging Modules
You can merge two LA modules to increase channel width. Such a merged
module functions as a single unit and the data it acquires is automatically
time-correlated. This is useful when analyzing buses or devices with a high pin
count. In addition, some microprocessor support packages require merged
modules.
Modules must have the same maximum state speed and must be physically
connected in the mainframe before they can be merged by software. Modules
must be adjacent and connected as described in the TLA 700 Series Logic
Analyzer Installation Manual.
When LA modules are merged, only one set of clock channels needs to be
connected to the target system to acquire data. This makes it easier to connect
and reduces capacitive loading.
Modules that have been physically connected in the mainframe, and are therefore
capable of being merged, are shown in the Merge Modules property page with a
merge button. See Figure 3–19.
H
To open the Merge Modules property page, go to the System menu and click
System Configuration. Then select the Merge Modules tab. To merge or
unmerge modules, click the merge button between the module icons.
Merge button
Figure 3–19: Merging modules
3–34
TLA 700 Series Logic Analyzer User Manual
Setup
NOTE. After the modules have been physically merged, you should run the
self-calibration procedure on the modules as a merged pair. To run the self-calibration procedure, go to the System menu and select Calibration and Diagnostics. Click Self Calibration.
You can unmerge the modules at any time for independent operation. You do not
have to remove the hardware connection between the modules.
In setup and data windows, merged module probe names use the following
convention: master module probe names are displayed normally, and slave
module probe names are prepended with an S.
Saving and Loading Setups, Triggers, and Data
Once you set up the logic analyzer to your satisfaction, you will probably want
to save the setup for future use. You can save setup information in two ways, a
saved system file or a saved module file.
Refer to the Logic Analyzer Conceptual Model described on page 2–6. The
modules consist of the setup, trigger, and data associated with the physical LA or
DSO module installed in the logic analyzer. The system consists of the setup and
data for the whole logic analyzer, including all the modules and all data
windows. See Figure 3–20.
When you save a module, you save all the setup and trigger information for that
module. When you save a system, you save all the setup information for the
system, including data window display settings, and all the module information,
as well. In either case, you have the option of saving acquired data.
System
Data Windows
General Settings
Module 1
Setup
Trigger
Data
Module 2
Setup
Trigger
Data
Module n
Setup
Trigger
Data
Figure 3–20: Logic analyzer conceptual model
TLA 700 Series Logic Analyzer User Manual
3–35
Setup
Saving System and
Module Files
Determine whether you want to save the information from just the module or for
all modules. Select Save System or Save Module accordingly. If you want to
save the data in addition to the setup and trigger information, select Save
Acquired Data.
You execute Save operations from the File menu.
NOTE. When saving systems or modules, be aware that the data is by far the
largest component of the save file. If the data is not important, you can save
significant disk space by saving the file without saving the data.
Saved system and module file names have a .tla file name extension (filename.tla). The initial default location for saved files is C:\My Documents.
Figure 3–21: Saving a system with data
Loading Saved System
and Module Files
3–36
The logic analyzer stores all the setup, trigger, and data information in just two
types of files: saved module and saved system. However, the logic analyzer can
extract different types of information individually from these files. From a saved
module file, you have the option of loading any of the following:
H
An LA module trigger program
H
A module setup and trigger program
H
Saved data from the module (accomplished by opening a saved data window;
see Opening a Saved Data Window on page 3–49)
TLA 700 Series Logic Analyzer User Manual
Setup
From a saved system file, you can load any of the following:
H
Any of the previous module-related choices
H
Full system setup, including data windows
H
Saved data from one or more modules
You execute Load operations from the File menu. For module Load operations,
you must first go to the module Setup or Trigger window before accessing the
File menu.
Loading a System. When you load a system you load the full system setup, which
includes setup, data, and trigger information for the logic analyzer and all
installed modules. If the saved system file included data, the data windows and
saved data are also loaded.
There may be situations where you attempt to load a saved system with a
different module configuration than your current system. The Load System
Options dialog box displays informing you of the differences. To load a module
from the saved system, drag the module icon from the top of the dialog box to a
module icon in the bottom of the dialog box. Figure 3–22 shows an example of
the Load System Options dialog box.
Figure 3–22: Load System Options dialog box
Loading a Setup and a Trigger Program. When you execute a Load System or
Load Module operation, you load a saved setup and its related trigger program(s)
to the logic analyzer (system) or specified module.
TLA 700 Series Logic Analyzer User Manual
3–37
Setup
Loading Saved Data. You can load saved data using the Load Data Window
selection in the Window menu. See Opening a Saved Data Window on
page 3–49 for more information.
Loading a Saved Trigger. You can load an LA module trigger without loading a
full setup. Saved system and module files both contain trigger program
information. When you load a trigger from the LA Trigger window, you can
select a saved system or module file as the source. When you do so, the logic
analyzer extracts only the trigger information from the file and loads it to the
module.
Creating a Personalized Trigger Library. To create your own trigger library, follow
these steps:
1. Create a folder in a convenient location. For example, create a folder named
Project Trigger Library in the folder My Documents. The path name would
be as follows:
2. Go to the Trigger window containing the trigger program you want to save.
3. Go to the File menu and select Save Module As.
4. In the Save As dialog box, navigate to your trigger library folder.
5. Name the new file, and use the Comment box to enter descriptive comments.
See Figure 3–23.
6. Make sure that Save Acquired Data is not selected.
7. Click Save.
Figure 3–23: Saving a file in a personalized trigger library
3–38
TLA 700 Series Logic Analyzer User Manual
Setup
Loading Default Settings
To return the logic analyzer to its default condition, go to the File menu and click
Default System.
System Options
The logic analyzer provides several property pages where you can set or change
system options. To access the system options, select Options from the System
menu and choose the property page you are interested in.
H
Use the Color property page to create, remove, and modify color schemes.
H
Use the Defaults property page to specify the defaults throughout the
TLA 700 application. The settings you enter will be the default settings when
you create new data windows.
H
Use the Preference property page to specify user preferences, such as
changing the color of the Run or Stop buttons or hiding the Status bar.
H
Use the Presets property page to view and modify preset names and values
such as probe threshold voltages and DSO vertical range or vertical offset
values.
H
Use the Start-Up property page to select which system setup (such as a
previous system or a saved system setup) to open after you power on the
logic analyzer.
H
Use the System Source Files property page to define the location of source
files and suffixes used to create new Source windows.
TLA 700 Series Logic Analyzer User Manual
3–39
Setup
Menu Shortcut Keys
You can use the shortcut keys listed in Table 3–5 to manipulate menus and edit
windows. You should also refer to the discussions of short cut keys in the online
help or under the section for the individual data windows.
Table 3–5: Menu shortcut keys
Desired action
Key combination
File menu
Return system to the default setups
CTRL + D
Load a saved system
CTRL + O
Save a system setup
CTRL + S
Print the active window
CTRL + P
Edit menu
Cut a selected item to the clipboard
CTRL + X
Copy a selected item to the clipboard
CTRL + C
Paste items from the clipboard
CTRL + V
Undo edit
CTRL + Z
Data menu
Search backward
CTRL + B
Search forward
CTRL + F
System menu
Display the Status Monitor
CTRL + M
Run or Stop
CTRL + R
Window menu
Create a new data window
3–40
CTRL + N
TLA 700 Series Logic Analyzer User Manual
Acquisition
After you set up the logic analyzer you are ready to acquire the data.
When you start an acquisition, all modules start acquiring data together.
(Exceptions are when one module has been programmed to arm another or when
a module has been turned off.) Modules stop acquiring data individually,
according to their trigger programming.
Starting and Stopping Acquisition
You control acquisition from the Control bar, shown below:
Starts/stops
acquisition
Displays Status
Monitor
Selects Repetitive or
Single-run mode
1. In the Control bar, click Run to start acquisition.
2. Wait for the logic analyzer to trigger and display data, or click Stop to
manually stop acquisition.
There are two ways to acquire data: Single-run or Repetitive mode. Within
Repetitive mode, you can specify the following three conditions:
H
Save Module and Data
H
Stop if Compare with Reference is Equal or Not Equal
H
Stop After N Acquisitions
When comparing acquisition data against reference data, you can view the results
in either a Listing window or in a Waveform window.
TLA 700 Series Logic Analyzer User Manual
3–41
Acquisition
Single Run Mode
In Single-run mode, the logic analyzer automatically stops acquiring and
displays data when it fulfills the setup conditions. Use Single-run mode when
you want to find and display a specific event.
During acquisition, the logic analyzer monitors the data, looking for the events
you specified in the Trigger windows. When the specified events occur, the logic
analyzer responds according to the selections you made in the Setup and Trigger
windows.
Repetitive Mode
In Repetitive mode, the logic analyzer keeps acquiring data until you click Stop
or until it fulfills the stop conditions.
You can use Repetitive mode as follows:
H
To observe the same waveform or listing for a period of time
H
To stop after a set number of acquisitions for a period of time and look for
differences
After each acquisition you can have the logic analyzer do the following tasks:
H
Save the system or module setups and data
H
Export the data to separate files or overwrite the same file
H
Compare the LA acquisition data against data in another LA module or a
saved LA module file
H
To open a file or execute a set of defined tasks after the acquisition is
complete. For example, you can run a WIndows 95 command such as
sending email or paging you that the logic analyzer has stopped.
Select Repetitive Properties from the System menu to select the different options
for the Repetitive mode. Figure 3–24 shows an example of the Repetitive
Properties dialog box.
NOTE. You can minimize the time between acquisitions by specifying compare
conditions under the LA Setup window, deleting (not just minimizing) all data
windows, and then starting the logic analyzer. When the logic analyzer fulfills
the compare conditions, you can create a new data window with the New Data
Window wizard to view the data.
3–42
TLA 700 Series Logic Analyzer User Manual
Acquisition
Figure 3–24: Defining setups for Repetitive mode
Viewing Acquisition Activity
While the logic analyzer is acquiring data, you can check its progress to see how
much data it has acquired or to view channel activity.
Use the Status Monitor for a brief summary of acquisition, trigger, and data
storage progress. See Figure 3–25.
H
In the Control bar, click Status.
Figure 3–25: The Status Monitor
TLA 700 Series Logic Analyzer User Manual
3–43
Acquisition
The Status Monitor is also useful to debug a trigger program. From the Status
Monitor you can view the current status of various resources of the logic
analyzer during acquisition. However, be aware that rapid changes in trigger
state, counter values, timer values, and the internal signals cannot be accurately
displayed in real time in the Status Monitor.
If the Logic Analyzer Does Not Trigger
If the logic analyzer does not trigger, then you should check the following:
LA Module
H
Check that your target system is powered on.
H
Check the System window to verify that required modules are turned on.
H
If the module has correctly clocked data, acquired the specified events,
triggered, but has not stopped, the module probably has not acquired enough
additional data to fill acquisition memory. Click Stop to manually stop the
acquisition, and then change the module Memory Depth (reduce) or Trigger
Position (increase).
The following conditions apply to the LA module only:
H
Check the Status Monitor for an external clock warning. If the LA is not
receiving an external clock, the Status Monitor displays the following
message: External Clock Source Idle.
H
Check for signal activity at the probe tip. If there is no activity, then check
the probe connections.
Check the clock signal to make sure that the LA module is actually clocking
data. Problems with the clock signal can impact setups using external
clocking, custom clocking (microprocessor support packages only), or
storage qualification.
3–44
H
Similar to the previous item, check clock qualifier signals and clocking
equations.
H
Check the threshold voltages for probes and clocks.
H
If the module is correctly clocking data and the data events have occurred,
but the trigger program did not generate a trigger, then you should check the
trigger program itself. The trigger program might not be reaching the state
that generates the trigger. Use the Status Monitor to track trigger program
progress and identify the state in which trigger progress stops.
TLA 700 Series Logic Analyzer User Manual
Acquisition
H
DSO Module
The following condition applies to the DSO module only:
H
Arming or Intermodule
Triggering
Check the complexity of your trigger program. If your trigger program is too
narrowly defined, or over-specified, the trigger program might not acquire
the desired data or might not trigger. A less-specific trigger program might
acquire the desired data and will also verify that you have set up the proper
clocking and threshold levels.
Check the trigger Mode setting. If Mode is set to Normal, and the data does
not meet the trigger conditions, the module will not trigger. (Conversely, if
Mode is set to Auto, the module will trigger after a set length of time, even if
the specified data does not occur.)
The following conditions apply only if you are using arming or intermodule
triggering:
H
Internal signal logic function. If your trigger depends on setting an internal
signal, and that signal has been set to Wired-And, all modules in the system
must set the signal or it cannot assert.
H
If any modules are turned off, check that the trigger program is not waiting
for input from an inactive module.
TLA 700 Series Logic Analyzer User Manual
3–45
Acquisition
3–46
TLA 700 Series Logic Analyzer User Manual
Display
To view acquired data, open one of the data windows. The Listing window and
the Waveform window are the data windows that you will use for most applications; see Figure 3–26. You can also create Source windows to use with
high-level language support applications or Histogram windows to use with
performance analysis applications. You can have multiple data windows to
display different data or different views of the same data.
Figure 3–26: The Listing and Waveform windows
Setup window and data window controls act independently of one another.
Controls in the Setup windows affect how the modules acquire data. Controls in
the data windows affect how the acquired data is displayed.
TLA 700 Series Logic Analyzer User Manual
3–47
Display
Opening an Existing Data Window
The System window shows the relationship between the modules and the data
windows.
H
To open a data window, go to the System window and click a data window
button. See Figure 3–27.
H
To see which modules supply data to a data window, go to the System
window and click the data window label.
Figure 3–27: Opening a data window
3–48
TLA 700 Series Logic Analyzer User Manual
Display
Opening a Saved Data Window
To open a window displaying data from a saved system file, do the following:
1. Go the Window menu and select Load Data Window.
2. Click Browse to search for the file or enter a path to the file in the text box.
NOTE. The saved file must be a saved system file.
3. Once the file is found, click Open.
4. Select the data window to load.
5. Click OK.
6. If the data window name is not unique, you will be prompted for a new
name. Enter a name and click OK.
Aligning Saved Data with Current Data
Saved data and current data are time-correlated by aligning their system triggers.
You can manually adjust this alignment using the Time Alignment dialog box.
To access the Time Alignment dialog box, go to the Data menu and select Time
Alignment, as shown below.
TLA 700 Series Logic Analyzer User Manual
3–49
Display
Creating a New Data Window
Use the New Data Window wizard to create a new data window for the data you
want to display. You can select data from any module, a saved system file, or
saved module file. See Figure 3–28.
Figure 3–28: New Data Window wizard
Create a new data window as follows:
1. Click the New Data Window icon in the toolbar.
2. Select the appropriate Window Type and click Next.
NOTE. The contents of the New Data Window wizard will vary depending on the
type of data window that you are creating.
3. For each page in the wizard, enter the required information and click Next.
4. On the last page, enter the name for the data window or use the default name
and then click Finish.
3–50
TLA 700 Series Logic Analyzer User Manual
Display
General Purpose Data Window Shortcut Keys
You can use the general-purpose shortcut keys listed in Table 3–6 to move data
and cursors in data windows. You should also refer to the discussions of short cut
keys in the online help or under the section for the individual data windows.
The shortcut keys (also known as accelerator keys or hot keys) abide by the
following rules:
H
Arrow keys with no modifier keys scroll data.
H
Arrow keys with the Control (CTRL) key move the active cursor.
H
The Shift key increases movement by a factor of 10.
Table 3–6: General purpose data window shortcut keys
Desired action
Key combination
Scroll data up 10 pages
Shift + Page Up
Scroll data down 10 pages
Shift + Page Down
Scroll data to the top of the window
Shift + Home
Scroll data to the end of the window
Shift + End
Move active cursor up one page
CTRL + Page Up
Move active cursor down one page
CTRL + Page Down
Move active cursor to the top of the data
CTRL + Home
Move active cursor to the end of the data
CTRL + End
Move active cursor up 10 pages
CTRL + Shift + Page Up
Move active cursor down 10 pages
CTRL + Shift + Page Down
Move active cursor to the top of the data
CTRL + Shift + Home
Move active cursor to the end of the data
CTRL + Shift + End
TLA 700 Series Logic Analyzer User Manual
3–51
Display
3–52
TLA 700 Series Logic Analyzer User Manual
Waveform Window
Use the Waveform window to display and evaluate acquisition data. You can
display both DSO waveforms and logic analyzer waveforms. Each window
contains a data area, waveform labels, marks and several toolbars that allow you
to measure and manipulate your waveforms. See Figure 3–29 for an example.
Each waveform is displayed independently within its own track. Waveforms
cannot be overlapped.
For the LA module, data values for each channel are shown as a digital
(two-state) waveform. Logic level low is drawn as a thick line; logic high as a
thin line. For the DSO module, data values for each channel are displayed as an
analog waveform.
Figure 3–29: Waveform window
TLA 700 Series Logic Analyzer User Manual
3–53
Waveform Window
Types of Waveforms
There are several types of waveforms that can be shown in the Waveform
window, as shown in Figure 3–30.
Sample clock waveform
Single-channel LA waveform
Busform LA waveforms
DSO waveform
Figure 3–30: Waveform types
Busforms
Single-Channel LA
Waveforms
Magnitude Waveforms
3–54
Busforms display the value of an LA module channel group.
Magnitude waveforms plot the numeric value of a channel group on a vertical
axis over a period of time. For example, you can use magnitude waveforms with
A/D and D/A applications for viewing the RGB components of a digitized video
signal. Figure 3–31 shows such a component.
TLA 700 Series Logic Analyzer User Manual
Waveform Window
Figure 3–31: Magnitude waveform
DSO Waveforms
Analog timing diagrams that represent a single DSO channel.
The size of the DSO waveform within its track depends on signal size and the
input voltage range selected in the DSO Setup Window.
Range readouts for DSO waveforms are located at top and bottom left of the
waveform. The range readouts show the maximum and minimum vertical input
voltage settings for the waveform. See Figure 3–32.
The ground line is shown as a horizontal dotted line through each DSO
waveform track. If ground is outside the bounds of the track, the ground line is
not shown.
The trigger threshold is indicated by a “T>” at the right edge of the track. The
trigger threshold is set in the DSO Trigger page of the DSO Setup window.
Figure 3–32: Range readouts
TLA 700 Series Logic Analyzer User Manual
3–55
Waveform Window
Sample Clock Waveforms
Each module that contributes current data to the window has its own Sample
Clock waveform. The sample clock waveform consists of a row of short vertical
tick marks placed along the time axis at each display point that represents an
actual acquired sample for the module.
Reading the Waveform Indicators
Data marks, cursors, and other indicators help you navigate and identify the data.
Figure 3–33 and Table 3–7 identify and describe data window marks.
H
To move cursors or marks, drag the cursor and mark handles. Trigger marks
and Begin/End data marks cannot be moved.
System trigger
Cursor 1
Begin data mark Cursor 2
End data mark
User mark
Data mark bar (fine control)
Split box
Overview mark bar (coarse control)
Figure 3–33: Waveform window cursors and marks
3–56
TLA 700 Series Logic Analyzer User Manual
Waveform Window
Table 3–7: Waveform window cursor and mark summary
Mark
Name
Description
System trigger
The system trigger is the reference point for the acquisition. Timing and location
information is relative to the system trigger. Trigger marks cannot be moved.
Under some conditions the system trigger associated with a module’s data might
not be displayed in the data window. If the system trigger was caused by another
module, whose data is not included in the current display, then the system trigger
is not shown. Nevertheless, all time measurements still relate to that system
trigger, even if it is not shown.
The system trigger associated with the current data is called the active system
trigger. The system trigger associated with saved data is called the reference
system trigger. The active system trigger is indicated by a yellow T; the reference
system trigger is indicated by a gray T.
Module trigger
The point at which the module triggered. Trigger marks cannot be moved.
Begin data / end data
The start and end of a module’s data record. These data marks cannot be moved.
Cursors 1 and 2
Moveable marks used for visual reference and for data measurements.
User mark
User-created marks. Use marks to make specific data more easy to identify and
find.
Adding a Mark to a
Waveform Window
You can mark interesting data that you may want to refer back to at a later time.
To add a user mark, follow these steps:
1. In the System window, click the Waveform window icon.
2. From the Edit menu select Add Mark. The mark appears at the center of the
display, has default properties, and is selected.
3. Move the mark to the desired location by dragging its handle.
NOTE. You cannot add a mark if you have not acquired data.
Sending Stacked Marks to
the Back
Sometimes, marks can be stacked on top of one another. To send a mark to the
back, follow these steps:
1. Select a mark you know is on top of another one.
2. Click the right mouse button and select Send To Back.
TLA 700 Series Logic Analyzer User Manual
3–57
Waveform Window
Cursor Measurements
Use the cursors to take time and voltage measurements. You take time and
voltage measurements in the Waveform window, as shown below.
The following steps describe how to take a time measurement. Use the same
method to take a voltage measurement for the DSO module. (Magnitude on an
LA module waveform is expressed as a 1 or a 0.)
1. In the Waveform window, select a waveform.
2. Move Cursor 1 to the location on the waveform that you want to measure.
3. Read the time from the C1 readout on the measurement bar.
4. Move Cursor 2 to another location on the waveform that you want to
measure.
5. Read the time from the C2 readout on the measurement bar.
6. Read the time difference between the two waveform locations from the Delta
readout on the measurement bar.
Cursor time is relative to the active system trigger.
3–58
TLA 700 Series Logic Analyzer User Manual
Waveform Window
Jumping to Specific Data Locations
You can use the Go To dialog box to jump to a new position by selecting any
current mark or waveform. See Figure 3–34.
H
To open the Go To dialog box, open a Waveform window and click the
Go To toolbar button, as shown in Figure 3–34.
Figure 3–34: Using the Go To dialog box to jump to the system trigger
You can also use the Overview Mark bar to quickly jump to another location. If
you do not click on a mark, clicking in the Overview Mark bar scrolls to that
location.
Figure 3–35: Using the Overview Mark bar to jump to a data location
TLA 700 Series Logic Analyzer User Manual
3–59
Waveform Window
Searching Data
Use the Define Search dialog box to search for specific data within the current
Waveform window. Searches are specific to the selected data source and begin
from the active cursor.
To search for a specific event in a Waveform window, follow these steps:
1. Open a Waveform window and click the Define Search toolbar button, as
shown.
2. Select the Data Source. See Figure 3–36.
3. Select the appropriate name.
4. Select the Condition.
5. Enter the Value, if appropriate.
6. Click Search Fwd or Search Back. The first occurrence is marked by
cursor 1.
You can search any data source available to the current data window, but Search
can only search one data source at a time. For additional searches of the same
event, click the Search Forward and Search Back arrow buttons in the toolbar.
NOTE. Data that is hidden cannot be found by the search function. For example,
if you turn off a waveform in the Waveform property page by unchecking Show
Waveform, the search function cannot search for data for that waveform.
3–60
TLA 700 Series Logic Analyzer User Manual
Waveform Window
Figure 3–36: Defining search criteria
Locking Windows
Locking windows provides an easy method to compare data from two different
windows. Use the Lock Windows dialog box, shown in Figure 3–37, to select
how windows are locked together.
H
To open the Lock Windows dialog box, go the System window and click the
button for the data window you want to open. Go to the View menu and
select Lock Windows.
Figure 3–37: Lock Windows dialog box
TLA 700 Series Logic Analyzer User Manual
3–61
Waveform Window
MagniVu Data
The LA modules have MagniVu data acquisition as a standard feature. MagniVu
data acquisition offers 500 picosecond high-speed timing simultaneous with
200 MHz state on all channels through the same probe; no double probing is
required. The record length for MagniVu data is 2000 samples. MagniVu data is
centered on the LA module trigger. Figure 3–38 shows an example of MagniVu
data.
You can view MagniVu data in both Listing and Waveform windows.
In Figure 3–38, the top waveforms were acquired at the fastest normal sample
rate. The MagniVu waveforms, in the lower part of the display, were acquired
through the same probe channels at the same time as the top waveforms.
Take a close look at the difference in the acquired data. First view the regular
data acquisition, which was sampled at 4 ns. The regular acquisition captured the
address bus as it made the transition from 34 to 44. The data shows an invalid
address of 74, and indicates that the invalid address lasts for the entire 4 ns
sample period. At the next sample, the address is shown correctly as 44.
Now view the MagniVu data acquisition, which was sampled at 500 ps. The
MagniVu data shows the same address bus transition from 34 to the invalid
address of 74, before settling to the correct address of 44. Note, however, that the
indicated settling time is different. The MagniVu data shows that the address bus
took approximately 500 ps to complete the transition, and shows the address bus
as 44 approximately 3.5 ns earlier than did the regular acquisition data.
Figure 3–38: MagniVu data
3–62
TLA 700 Series Logic Analyzer User Manual
Waveform Window
To display MagniVu data, load the MagniVu data source as follows:
1. Open a data window that contains acquired data.
2. Click Add Column or Add Waveform.
3. Select the MagniVu data source. If the source you want is not listed, click
Add Data Source and add the one you want to the list. See Figure 3–39.
4. Click Add. The column or waveform appears in the data window.
Figure 3–39: Adding a MagniVu data source to a data window
Comparing Waveform Data
When comparing data against reference data, you can highlight data that is equal
to or not equal to the reference data.
NOTE. Before you can display compare data, you must define the compare
parameters in the Define Compare Dialog box in the LA Setup window. Refer to
Memory Compare beginning on page 3–4 for information on setting up the
compare parameters.
TLA 700 Series Logic Analyzer User Manual
3–63
Waveform Window
The following steps describe how to display compare data in the Waveform
window.
1. Open a Waveform window and click the Properties toolbar button, as shown.
2. Select the Waveform Window property page.
3. Select Show Compare and select one of the colors for when data does not
equal the reference data (Acq!=Ref).
If you want to highlight data that does equal the reference data, select
Acq=Ref and the appropriate color (see Figure 3–40).
Figure 3–40: Selecting compare data colors in the Waveform Window property page
4. Click OK.
The data differences or equalities will be highlighted in colors you specified,
similar to Figure 3–41.
3–64
TLA 700 Series Logic Analyzer User Manual
Waveform Window
Figure 3–41: Viewing LA compare data in a Waveform window
NOTE. For more information on comparing data, refer to Guidelines for Memory
Compare on page 3–6.
Adjusting the Waveform Data View
There are a number of actions you can perform in the Waveform window to get
the exact view of the data that you want.
Waveform Window
Toolbar
The toolbar has shortcut buttons for common operations, as shown below:
Search forward
Define search
Search backward
Cut
Copy
Paste
Add mark
Add waveform
Moving Waveforms
Zoom in
Zoom out
Properties
Go To
Select the waveform labels and then drag them to their new location.
TLA 700 Series Logic Analyzer User Manual
3–65
Waveform Window
Adding a New Waveform
or a Data Source
Click the toolbar Add Waveform button to open the Add Waveform dialog box.
Then select the data source and its associated group or channel to add it to the
display.
To select a group, first select By Group. (See Figure 3–42.) Then, from the list,
select a group name indicated by a the + symbol. Default groups are displayed as
busforms. (You can also choose to display a group as a magnitude waveform.
Double-click the waveform label. From the waveform properties page, click
Options and select Magnitude.)
To select individual channels, first select By Probe. Then, from the list, select the
channel(s). If you have named individual channels in the LA Setup window, you
can select By Name to list just those channels.
If the data source you want is not listed, click Add Data Source and find and
select the source. (The data source can be an installed module or a saved module
file.) See Figure 3–42.
New waveforms are added after the selected waveforms or after all waveforms if
none are selected.
Figure 3–42: Add Waveform dialog box
Deleting Waveforms
3–66
Select the waveform labels, then click the Cut toolbar button.
TLA 700 Series Logic Analyzer User Manual
Waveform Window
Changing Waveform Label
Width
Changing Waveform
Height
Drag the waveform label border as shown.
To change the height of a waveform, double-click on the waveform label to open
the Waveform property page. Enter a new value or use the spinbox controls to
change the value in the Height box.
In addition to adjusting the height using the Waveform property page, you can
select the waveform, and adjust the waveform from the front-panel Size control
on the portable mainframe.
Changing the Displayed
Time/Div
Cut, Copy, and Paste
Viewing Glitches
Change the displayed time per division using the Time/Div toolbar control. For a
quick change, use the Zoom In and Zoom Out toolbar buttons. You can continue
to click the toolbar buttons until you reach the desired horizontal scale.
You can cut, copy, and paste waveforms and marks.
Glitches are indicated on a waveform by a block of color behind the waveform.
See Figure 3–43. Turn the glitch display on or off from the Waveform window
property page.
NOTE. To view glitches in a data window, you must enable Glitch storage in the
Setup window before acquiring data.
Glitch
Figure 3–43: Waveform with a glitch
Naming Waveforms
Rename a waveform by returning to the Setup window and changing the channel
or channel group name.
TLA 700 Series Logic Analyzer User Manual
3–67
Waveform Window
Splitting the Data Area
You can split the data area to compare waveforms that are far away from each
other within the display. Drag the split box from the top end of the vertical scroll
bar.
Customizing the Waveform Window Data
Use property sheets to customize data windows. Property sheets control aspects
of the display such as size, color, and in some cases, enabling or disabling
whether an element is shown. Click the Properties toolbar button to open the
data window property sheet. Figure 3–44 shows a property page.
Figure 3–44: Property page
Exporting Waveform Data
You cannot export waveform data directly. However, you can add DSO
waveform information as a column in a Listing window and then export the data
as a listing file. Refer to Exporting Listing Data on page 3–82 or more information on exporting data.
3–68
TLA 700 Series Logic Analyzer User Manual
Waveform Window
Printing Waveform Data
You can print a hardcopy of the Waveform window or you can print the image to
a file. You can print a single page, a range of pages, or you can print a range of
data between two marks or cursors.
1. Go to the File menu and select Print.
2. Select Print to File, or select your printer in the window.
3. Select the print range and click OK.
When you click OK a confirmation message displays, informing you of the
number of approximate pages that will be printed.
4. Click OK again to confirm your actions.
5. To interrupt printing at any time, press ESC.
The contents of the window will be sent to the printer or to the specified file.
TLA 700 Series Logic Analyzer User Manual
3–69
Waveform Window
Waveform Window Shortcut Keys
You can use the general-purpose shortcut keys listed in Table 3–8 to move data
and cursors in the Waveform window. You should also refer to the discussions of
short cut keys in the online help or under the section for the individual data
windows.
The shortcut keys (also known as accelerator keys or hot keys) abide by the
following rules:
H
Arrow keys with no modifier keys scroll data.
H
Arrow keys with the Control (CTRL) key move the active cursor.
H
The Shift key increases movement by a factor of 10.
Table 3–8: Waveform window shortcut keys
3–70
Desired action
Key combination
Go to next trigger
CTRL + T
Display Go To dialog box
CTRL + G
Move Cursor 1 to the center of the window
CTRL + 1
Move Cursor 2 to the center of the window
CTRL + 2
Zoom in
CTRL + I
Zoom out
CTRL + U
Add a mark
CTRL + K
Add a waveform
CTRL + W
Scroll data left 50 pixels
Shift + Left arrow
Scroll data right 50 pixels
Shift + Right arrow
Move active cursor left five pixels
CTRL + Left arrow
Move active cursor right five pixels
CTRL + Right arrow
Move active cursor left 50 pixels
CTRL + Shift + Left arrow
Move active cursor right 50 pixels
CTRL + Shift + Right arrow
TLA 700 Series Logic Analyzer User Manual
Listing Window
Use the Listing window to view and evaluate acquisition data. Data is presented
as tabular text in columns that represent channel groups. Other columns are
sample numbers and time stamp values. See Figure 3–45 for an example.
This window displays the amount of data you specified in Setup and Trigger
windows. Each row in the table consists of data sampled on one acquisition
cycle, and is assigned a sample number. Sample numbers are relative to the
beginning of memory.
Figure 3–45: Listing window
Reading the Listing Window Indicators
Data marks, cursors, and other indicators help you navigate and identify the data.
Figure 3–46 and Table 3–9 identify and describe data window marks.
H
To move cursors or marks, drag the cursor and mark handles. Trigger marks
and Begin/End data marks cannot be moved.
TLA 700 Series Logic Analyzer User Manual
3–71
Listing Window
Module trigger
System trigger
Overview mark bar
(coarse control)
Cursors
User mark
End data mark
Data mark bar
(fine control)
Split box
Figure 3–46: Listing window cursors and marks
Table 3–9: Listing window cursor and mark summary
Mark
Name
Description
System trigger
The system trigger is the reference point for the acquisition. Timing and location
information is relative to the system trigger. Trigger marks cannot be moved.
Under some conditions the system trigger associated with a module’s data might
not be displayed in the data window. If the system trigger was caused by another
module, whose data is not included in the current display, then the system trigger
is not shown. Nevertheless, all time measurements still relate to that system
trigger, even if it is not shown.
The system trigger associated with the current data is called the active system
trigger. The system trigger associated with saved data is called the reference
system trigger. The active system trigger is indicated by a yellow T; the reference
system trigger is indicated by a gray T.
3–72
Module trigger
The point at which the module triggered. Trigger marks cannot be moved.
Begin data / end data
The start and end of a module’s data record. These data marks cannot be moved.
Cursors 1 and 2
Moveable marks used for visual reference and for data measurements.
User mark
User-created marks. Use marks to make specific data more easy to identify and
find.
TLA 700 Series Logic Analyzer User Manual
Listing Window
Adding a Mark to a Listing
Window
You can mark interesting data that you may want to refer back to at a later time.
To add a user mark, follow these steps:
1. In the System window, click the Listing window icon.
2. From the Edit menu select Add Mark. The mark appears at the center of the
display, has default properties, and is selected.
3. Move the mark to the desired location by dragging its handle.
NOTE. You cannot add a mark if you have not acquired data.
Sending Stacked Marks to
the Back
Sometimes, marks can be stacked on top of one another. To send a mark to the
back, follow these steps:
1. Select a mark you know is on top of another one.
2. Click the right mouse button and select Send To Back.
Jumping to Specific Data Locations
You can use the Go To dialog box to jump to a new position by selecting any
current mark or waveform. See Figure 3–47 on page 3–74.
H
To open the Go To dialog box, open a data window and click the Go To
toolbar button, as shown in Figure 3–47.
TLA 700 Series Logic Analyzer User Manual
3–73
Listing Window
Figure 3–47: Using the Go To dialog box to jump to the system trigger
You can also use the Overview Mark bar (see Figure 3–48) to quickly jump to
another location. If you do not click on a mark, clicking in the Overview Mark
bar scrolls to that location.
Figure 3–48: Using the Overview Mark bar to jump to a data location
3–74
TLA 700 Series Logic Analyzer User Manual
Listing Window
Measuring Listing Data
Use the cursors to take time measurements. You take time measurements in the
Listing window, as shown below.
The following steps describe how to take a time measurement.
1. In the Listing window, move Cursor 1 to the location that you want to
measure.
2. Read the time from the C1 readout on the measurement bar. Cursor time is
relative to the active system trigger.
3. Move Cursor 2 to another location that you want to measure.
4. Read the time from the C2 readout on the measurement bar.
5. Read the time difference between the two locations from the Delta readout
on the measurement bar.
Comparing Listing Data
When comparing data against reference data, you can highlight data that is equal
to or not equal to the reference data.
NOTE. Before you can display compare data, you must define the compare
parameters in the Define Compare dialog box in the Setup window. Refer to
Memory Compare beginning on page 3–4 for information on setting up the
compare parameters.
The following steps describe how to display compare data in the Listing window.
1. Open a Listing window and click the Properties toolbar button, as shown.
2. Select the Listing Window property page.
TLA 700 Series Logic Analyzer User Manual
3–75
Listing Window
3. Select Show Compare, and select one of the colors for when data does not
equal the reference data (Acq!=Ref). See Figure 3–49.
4. If you want to highlight data that does equal the reference data, select
Acq=Ref and the appropriate color.
Figure 3–49: Selecting compare data colors in the Listing Window property page
5. Click OK.
The data differences or equalities will be highlighted in colors you specified,
similar to Figure 3–50.
NOTE. For more information on comparing data, refer to Guidelines for Memory
Compare on page 3–6.
3–76
TLA 700 Series Logic Analyzer User Manual
Listing Window
Figure 3–50: Viewing LA compare data in a Listing window
Searching Data
Use the Define Search dialog box to search for specific data within the current
Listing window. Searches are specific to the selected data source and begin from
the active cursor.
To search for a specific event in a Listing window, follow these steps:
1. Open a Listing window and click the Define Search toolbar button, as
shown.
2. Select the Data Source. See Figure 3–51.
3. Select the appropriate name.
4. Select the Condition.
5. Enter the Value, if appropriate.
6. Click Search Fwd or Search Back. The first occurrence is marked by
cursor 1.
TLA 700 Series Logic Analyzer User Manual
3–77
Listing Window
You can search any data source available to the current data window, but Search
can only search one data source at a time. For additional searches of the same
event, click the Search Forward and Search Back arrow buttons in the toolbar.
NOTE. Data that is hidden cannot be found by the search function. For example,
if you turn off a column display in the Column properties page by unchecking
Show Column, you cannot search for data in that column.
Figure 3–51: Defining search criteria
Locking Windows
Locking windows provides an easy method to compare data from two different
windows. Use the Lock Windows dialog box, shown in Figure 3–52, to select
how windows are locked together.
H
3–78
To open the Lock Windows dialog box go the System window and click the
button for the data window you want to open. Go to the View menu and
select Lock Windows.
TLA 700 Series Logic Analyzer User Manual
Listing Window
Figure 3–52: Lock Windows dialog box
MagniVu Data
The LA modules have MagniVu data acquisition as a standard feature. MagniVu
data acquisition offers 500 picosecond high-speed timing simultaneous with
200 MHz state on all channels through the same probe; no double probing is
required. The record length for MagniVu data is 2000 samples.
You can view MagniVu data in both Listing and Waveform windows. For more
information on MagniVu data, refer to MagniVu Data beginning on page 3–62.
Adjusting the Listing Data View
There are a number of actions you can perform in the Listing window to get the
exact view of the data that you want.
Listing Window Toolbar
The toolbar has shortcut buttons for common operations, as shown below.
Add mark
Paste
Add column
Copy Go To
Properties
Cut
Font size
Changing the Display Font
Size
Search
Click the Font Size toolbar buttons, shown in the previous figure. You can
continue to click the toolbar buttons until the text reaches the desired size. You
can also set the font to a specific size in the Listing Window property sheet.
TLA 700 Series Logic Analyzer User Manual
3–79
Listing Window
Moving Columns
Adding a New Column or
Data Source
Select the column labels and then drag them to their new location.
Click the toolbar Add Column button to open the Add Column dialog box. Then
select the data source and its associated group or channel to add it to the display.
If the data source you want is not listed, click Add Source and find and select the
source. The data source can be an installed module or a saved module file. See
Figure 3–53.
New columns are added after (to the right of) the selected columns or after all
columns if none are selected.
Figure 3–53: Add Column dialog box
Deleting Columns
Select the column labels, then click the Cut toolbar button.
Changing Column Width
Double-click the column label to open the Column Properties page. Enter a new
value for the column width. If you have a portable mainframe, you can also
change the column width by selecting the column label and use the front panel
Scale control to set the width.
Cut, Copy, Paste
You can cut, copy, and paste columns and marks. You can also copy textual data
from the listing to the clipboard. From there you can paste it to other areas, such
as the Define Search dialog box or the Clause Definition dialog box in the
Trigger window.
3–80
TLA 700 Series Logic Analyzer User Manual
Listing Window
Changing Radixes
Viewing Qualification
Gaps
To change a column radix in the Listing window, double-click the column label
to open the Column Properties page. Select a new radix. To select the Symbolic
radix, you must have loaded a symbol table. See Symbol Support beginning on
page 2–21 for information about using symbols and symbol table files.
Qualification gaps indicate that data samples were not stored due to storage
qualification or Don’t Store trigger actions.
Qualification gaps are indicated with a horizontal gray line above the first data
after the gap. Turn qualification gaps on or off from the Listing Window property
page.
Viewing Glitches
Glitches are indicated by highlighted text of the complete sample for all radixes
except binary, octal, and hexadecimal. In those radixes, only the glitch bits are
highlighted. Turn glitches on or off from the Listing Window property page.
NOTE. To view glitches in a data window, you must enable Glitch storage in the
LA Setup window before acquiring data.
Naming Columns
Changing the
Disassembly Format
Splitting the Data Area
Rename a column by returning to the LA Setup window and changing the
channel group name.
For microprocessor support packages, you can change the disassembly format
used in the Listing window. Use the Disassembly property page to select the
display format of disassembly groups. You must have a support package loaded
for this page to be active.
You can split the data area to compare columns that are far away from each other
within the display. Drag the split box from the left end of the horizontal scroll
bar.
Customizing the Listing Window Data Area
Use property sheets to customize data in the Listing window. The property sheets
control aspects of the listing display such as size, color, and in some cases,
enabling or disabling whether an element is shown. Click the Properties toolbar
button to open the Listing Window property sheet. Then select one of the
property sheets to change the data you are interested in.
TLA 700 Series Logic Analyzer User Manual
3–81
Listing Window
Exporting Listing Data
Use the Export Data dialog box to export data from the current listing window to
a text file or to a binary file. This is a way to print a copy of a complete or partial
listing. Figure 3–54 shows the Export Data dialog box.
Figure 3–54: Export Data dialog box
You can export the following listing data:
3–82
H
All listing data from the acquisition
H
Listing and DSO voltage measurement from a Listing window
H
A range of listing data between two selected marks
H
A range of listing data between two samples
TLA 700 Series Logic Analyzer User Manual
Listing Window
Exporting Data to an
ASCII File
If you want to export data to a text file, click Options to define the format of the
data in the Export Data Options dialog box (see Figure 3–55). The data is saved
in a text file with the .txt file name extension.
Figure 3–55: Export Data Options dialog box
Use the Export Data Options dialog box to customize the listing data for a text
file. You can specify the field delimiter to separate the listing columns. You can
also specify that measurement units should be included with the data. If you
export the data without unit characters, the time stamp values are in picoseconds
and the DSO values are listed in volts.
To export listing data, follow these steps:
1. In the System window, select a Listing window.
2. Go to the File menu and select Export Data.
3. In the Export Data dialog box, select the folder to which you want to export
data. Otherwise, leave the default of My Documents.
4. Click Options to specify any export options for the text data and then click
OK.
5. Enter a name for the exported file.
6. Specify the export range.
7. Click Save.
Exporting Data as a
Binary File
You can also export the listing data as a binary file with a .tbf (TLA 700 Binary
Format) file name extension. This option is only available if the data window is
from a single data source. You can export any data that appears in a Listing
window, including DSO and MagniVu data. This option is useful when you write
applications that need to use binary data. It is also faster than exporting an ASCII
file and the file size is often smaller.
TLA 700 Series Logic Analyzer User Manual
3–83
Listing Window
LA Module Binary Export File Format. The LA module binary data is exported as a
stream of bytes with the following characteristics:
H
The binary data uses big-endian fields (the most-significant bit is the
left-most bit).
H
Each group column field is zero-padded on the most-significant end to the
nearest byte.
H
Sample numbers and mnemonics groups are not exported.
H
Time stamp data is seven bytes wide and represents the number of picoseconds since the start of the acquisition.
H
The left-most column in the Listing window display corresponds to the first
exported field of a sample.
H
The first sample in the Listing window appears at the beginning of the
exported file.
H
MagniVu data follows the same guidelines as regular listing data.
DSO Module Binary Export File Format. The DSO module binary data (when used
in a Listing window) is exported as a stream of bytes with the following
characteristics:
H
The binary data uses little-endian fields (the most-significant bit is the
right-most bit).
H
Each channel field is a 16-bit value.
H
Sample numbers, mnemonics groups, and time stamp values are not
exported.
H
The left-most column in the Listing window display corresponds to the first
exported field of a sample.
H
The first sample in the Listing window appears at the beginning of the
exported file.
H
DSO data values are in twos-compliment format.
H
The formula used for converting a DSO channel field into a voltage is:
((Vertical range in volts / 64512) X channel field) +
vertical offset in volts
3–84
TLA 700 Series Logic Analyzer User Manual
Listing Window
Printing Listing Data
You can print a hardcopy of the Listing window or you can print the image to a
file. You can print a single page, a range of pages, or you can print a range of
data between two marks or cursors.
1. Go to the File menu and select Print.
2. Select Print to File, or select your printer in the window.
3. Select the print range and click OK.
When you click OK a confirmation message displays, informing you of the
approximate number of pages that will be printed.
4. Click OK again to confirm your actions.
5. To interrupt printing at any time, press ESC.
The contents of the window will be sent to the printer or to the specified file.
NOTE. The print selection prints a copy of the current Listing window. If you
want to print a text file, use the Export Data option to save the Listing window
contents to a file and then send that file to a printer.
TLA 700 Series Logic Analyzer User Manual
3–85
Listing Window
Listing Window Shortcut Keys
You can use the general-purpose shortcut keys listed in Table 3–10 to move data
and cursors in the Listing window. You should also refer to the discussions of
short cut keys in the online help or under the section for the individual data
windows.
The shortcut keys (also known as accelerator keys or hot keys) abide by the
following rules:
H
Arrow keys with no modifier keys scroll data.
H
Arrow keys with the Control (CTRL) key move the active cursor.
H
The Shift key increases movement by a factor of 10.
Table 3–10: Listing window shortcut keys
3–86
Desired action
Key combination
Go to next trigger
CTRL + T
Display Go To dialog box
CTRL + G
Move Cursor 1 to the center of the window
CTRL + 1
Move Cursor 2 to the center of the window
CTRL + 2
Add a mark
CTRL + K
Add a column
CTRL + L
Scroll data up 10 samples
Shift + Up arrow
Scroll data down 10 samples
Shift + Down arrow
Move active cursor up one sample
CTRL + Up arrow
Move active cursor down one sample
CTRL + Down arrow
Move active cursor up 10 samples
CTRL + Shift + Up arrow
Move active cursor down 10 samples
CTRL + Shift + Down arrow
TLA 700 Series Logic Analyzer User Manual
Source Window
Use the Source window to display the high-level language (HLL) source code
that you wrote correlated to your code as it was executed by your target system
and acquired by the logic analyzer. The logic analyzer links the Source and
Listing windows, and provides additional tools to help you view the tools and
data. See Figure 3–56 for an example of a Source window.
The data area of the Source window lists the content of the source file including
line numbers for each source code statement. The path name of the file displays
immediately above the source data.
Figure 3–56: Source window
You can use controls to step through data, move between user-defined marks,
and scroll through data. These controls directly affect the active cursor in the
associated Listing window and indirectly affect the active cursor in the Source
window.
TLA 700 Series Logic Analyzer User Manual
3–87
Source Window
Creating a Source Window
Before creating a Source window you should load a microprocessor support
package. You should also set up the Listing window you will use with the Source
window.
Create a new Source window with the New Data Window wizard as follows:
1. Click the New Data Window icon in the toolbar.
2. Select Source and click Next.
3. Select an existing Listing window.
4. Click Next.
5. Select the name of the Listing window, the data source, and the listing
column (normally an address column).
6. Enter the name of the symbol file or click Symbol File to browse the file
system for the symbol file.
The symbol file contains all of the information for the source window, such
as function, variable, and source code symbols.
7. Click Next.
8. Enter a name for the Source window or use the default name.
9. Click Finish.
10. If the Source File Locator dialog box appears, enter the path name for the
source file or click Browse to look for the file listed in the dialog box.
11. The new Source window will display the contents of the source file.
3–88
TLA 700 Series Logic Analyzer User Manual
Source Window
Reading the Source Window Indicators
Data marks, cursors, and other indicators help you navigate and identify the data.
Figure 3–57 and Table 3–11 identify and describe data window marks.
H
To move cursors or marks, drag the cursor and mark handles.
User mark
Cursor
Data mark bar
(fine control)
Overview mark bar
(coarse control)
Figure 3–57: Source window cursors and marks
Table 3–11: Source window cursor and mark summary
Mark
Name
Description
Cursors 1 and 2
Moveable marks used for visual reference and for data measurements.
User mark
User-created marks. Use marks to make specific data more easy to identify and
find.
TLA 700 Series Logic Analyzer User Manual
3–89
Source Window
Adding a Mark to a Source
Window
To add a user mark to a Source window, follow these steps:
1. In the System window, click the Source window icon.
2. Point the mouse at the source statement where you want to add the mark.
3. Right-click the mouse and select Add Mark. The mark appears in the display,
has default properties, and is selected.
4. If necessary, move the mark to the desired location by dragging its handle.
NOTE. You cannot add a mark if there is no data.
Sending Stacked Marks to
the Back
Sometimes, marks can be stacked on top of one another. To send a mark to the
back, follow these steps:
1. Select a mark you know is on top of another one.
2. Click the right mouse button and select Send To Back.
Jumping to Specific Data Locations
You can use the Go To dialog box to jump to a new position by selecting any
current mark or waveform. See Figure 3–58.
H
3–90
To open the Go To dialog box, open a data window, and click the Go To
toolbar button, as shown in Figure 3–58.
TLA 700 Series Logic Analyzer User Manual
Source Window
Figure 3–58: Using the Go To dialog box to jump to the cursor location
You can also use the Overview Mark bar to quickly jump to another location. If
you do not click on a mark, clicking in the Overview Mark bar scrolls to that
location.
Figure 3–59: Using the Overview Mark bar to jump to a data location
TLA 700 Series Logic Analyzer User Manual
3–91
Source Window
Moving the cursor between statements in the Source window does not necessarily move the cursor in the same direction in the Listing window. This can happen,
for example, if the statement in the new location was executed both before and
after the statement in the old location, such as when the statement is in a loop.
The Scan Listing box sets the scan direction in a Listing window when you
move the cursor in the Source window.
Moving Through Source Files
There are several ways of moving through the data in source files. You can move
through source files from the Source window or from the Listing window. When
you move a cursor in one window, the corresponding cursor in the other window
also moves.
Use the Step Forward or the Step Backward buttons (see Figure 3–60) to step
through source statements in execution order in the Source window. You can also
use the Next Mark or the Previous Mark buttons to jump to the next or previous
executed source statement that has a user-defined mark.
Use the cursor controls in either window to move the cursors. You can also move
the cursors in either window by clicking and dragging the cursor handles or by
adjusting the cursor spin box controls.
Next
Mark
Step
Backward
Step
Forward
Active
Cursor
Previous
Mark
Figure 3–60: Source window controls
3–92
TLA 700 Series Logic Analyzer User Manual
Source Window
Source-Relative Cursor
Positioning
Source-relative cursor positioning refers to updating the Listing window cursor
positioning as a result of changing the position of the active cursor in the Source
window.
When you move the Source window cursor to a new statement, the Source
window determines the address range of the source statement based on information from the loaded symbol file. The Source window uses the setting of the
Scan Listing mode to determine the search direction in the Listing window. The
Listing window searches the acquisition data for a matching address. When the
matching address is found, the active cursor in the Listing window is moved to
the matching sample.
If the Source window cursor is moved to a non-executable statement, such as a
comment, the address of the next executable statement is used.
Listing-Relative Cursor
Positioning
Listing-relative cursor positioning refers to updating the Source window cursor
position of the active cursor in the Listing window.
When you move the Listing window cursor to a new sample, the active Source
window cursor attempts to move to a corresponding source statement in the
Source window. The Source window uses information from the loaded symbol
file to convert the address of the Listing cursor position to a source file name and
statement (line number) location. The Source window then updates the active
Source window cursor position and displays the corresponding source statement.
Step Forward and Step
Backward Buttons
Use the Step Forward and Step Backward buttons to trace the execution order of
source statements. Click the Step Forward button to move to the next executed
source statement. Click the Step Backward button to move to the previous
executed source statement.
When you click the Step Forward or Step Backward buttons, the Source window
tells the Listing window to search forward or backward beginning at the active
Listing cursor for the next or previous executed source statement. When a match
is found, the Listing window positions the active Listing cursor to the matching
sample. The Source window converts the address to a file name and line number,
and then updates the active Source cursor position to the corresponding source
statement. The statement may be located in a source file that is different than the
original displayed file. In this case, the new file is displayed and the cursor is
placed on the proper statement.
A single line in the Source window may consist of more than one statement, for
example:
TLA 700 Series Logic Analyzer User Manual
3–93
Source Window
The next executed statement in the Listing window may appear on the same line
in the Source window as the current statement. However, the next executed
statement may also appear on a different line (before or after the current
statement), or in a different file. Click the Step Forward and Step Backward
buttons to move the cursor between statements in execution order.
The ability of the Source window to discriminate between multiple statements on
the same line depends on the amount of information provided by the code-generation tools. If there is enough information to identify multiple statements per
line, the Source window cursors will include character highlighting to identify
individual statements on a line.
Next Mark and Previous
Mark Buttons
Use the Next Mark and Previous Mark buttons to move the active cursor in the
Source window to the next or previous executed user-defined mark position (if
any marks have been defined). Next and previous refer to the execution sequence
and not to the position of the mark in the window.
The Next Mark and Previous Mark buttons operate similar to the Step Forward
and Step Backward buttons. However, rather than stepping through every
executed statement, you can define marks in the Source window as breakpoints
and then step between marks in execution order to move though the source code.
When you click the Next Mark or Previous Mark buttons, the Source window
tells the Listing window to search for addresses corresponding to the marked
source statements. When a corresponding sample is found, the Listing window
positions its active cursor to the matching sample. The Source window converts
the address to a file name and line number. It then updates the active Source
cursor position and displays the corresponding source statement.
If the code-generation tools provide column information for symbol files, you
can mark individual statements of multiple-statement lines in the source code.
You can then use the Next Mark and Previous Mark buttons to step between the
marks and highlight the individual statements.
The Next Mark and Previous Mark buttons are not active if there are no marks
defined in the Source window.
Active Cursor Readout
The active cursor readout displays the address of the source statement at the
active cursor. The address shown is the low address bound. The radix of the
address is always hexadecimal. If you position the cursor on a non-executable
statement, such as a comment or white space, the address of the next executable
statement is displayed.
Use the active cursor readout to jump to a new location in the source file. Enter
an address in this field and the active cursor moves to the corresponding
statement. If you enter an address that does not correspond directly to the address
of a source statement, the next statement will be used and the address is adjusted.
3–94
TLA 700 Series Logic Analyzer User Manual
Source Window
You can copy and paste the readout value into other locations such as in the
event portion of the Clause Definition dialog in the LA Trigger window.
Uncorrelated State
There are situations when you move the cursor in the Listing window to a
location where there is no corresponding source statement. The cursor in the
Source window remains at the current location and changes the color of the
Source window to signify an uncorrelated state exists between the Source and
Listing windows. When this happens, you can click the Step Forward or the Step
Backward buttons to search for an executable source line in the Listing window;
this correlates the active cursors in both windows.
Clicking the buttons forces the Listing window to search for a data sample that
corresponds to the next or previous line of executed source code. The line of
executed code may be in a different source file. If this happens, the Source
window displays the required file or prompts you for a path name. The ability to
locate source files depends on the Search Path List and Suffix List defined in the
Source Files property page.
Searching for Source Data
Use the Define Search dialog box to search for specific text patterns. You can
search the current source file or search all of the source files identified by the
loaded symbol file.
To search for a specific data pattern in a Source window, follow these steps:
1. Open a Source window and click the Define Search toolbar button, as
shown.
2. Select All Files or This File. See Figure 3–61.
3. Enter the text pattern.
4. Click Search Fwd or Search Back. The first occurrence is marked by the
active cursor.
You can search for any text pattern including leading and embedded white space;
trailing white space is ignored.
TLA 700 Series Logic Analyzer User Manual
3–95
Source Window
When searching for data in multiple files, the search operation follows the order
of files listed in the Source Window property page in the Displayed Source File
list. When you search for data in all files and one or more of the files cannot be
found, the Source File Locator dialog box displays, asking you to specify the
location of the file.
If the search is not completed in a set amount of time, the Search Progress dialog
box shows the status of the search. You can let the search continue, or you can
click Abort to stop the search.
Figure 3–61: Defining source search criteria
Adjusting the Source Data View
There are a number of actions you can perform in the Source window to get the
exact view of the data that you want.
Source window Toolbar
3–96
The toolbar has shortcut buttons for common operations.
TLA 700 Series Logic Analyzer User Manual
Source Window
Add mark
Copy
Cut
Go To
Paste
Changing the Display Font
Size
Cut, Copy, Paste
Turning Line Numbers On
or Off
Font Size
Search
Properties
Click the Font Size toolbar buttons, shown in the previous figure. You can
continue to click the toolbar buttons until the text reaches the desired size. You
can also set the font to a specific size in the Source window property sheet.
You can cut, copy, and paste columns and marks. You can also copy text data to
the clipboard. From there you can paste it to other areas, such as the Define
Search dialog box or the Clause Definition dialog box in the Trigger window.
Turn source line numbers on or off by clicking Line Number Column in the
View menu.
Customizing the Source Window Data Area
Use property sheets to customize data in the Source window. The property sheets
control aspects of the source display such as source files, text size, colors, tab
spacing, and source file locations. Click the Properties toolbar button to open the
Source window property sheet. You can also click the label above the data area
to open the property sheet. Then select one of the property sheets to change the
data you are interested in.
Locating Source Files
You can define the location of source files with the Source Files property page
(see Figure 3–62 on page 3–98). Use the property page to list the locations of
source files as well as possible file suffixes that can be attached to the file names
(used for compilers that do not include the file suffixes). A similar property page
(System Source Files property page) is used as a default list of locations of
source files and suffixes. The logic analyzer uses this list every time you create a
new source window.
The Source window uses the file path and file suffix in combination to locate the
correct source file. It searches for the file name in each directory indicated by the
file path list in the order specified. If a file name does not have a suffix, then
suffixes from the suffix list are tried until a match is found or all file path and
suffix combinations are exhausted.
TLA 700 Series Logic Analyzer User Manual
3–97
Source Window
Figure 3–62: Source Files property page
When specifying the search path, you can use an asterisk (*) as the final
component of a search path directory. For example, if you specify the following
path, C:\MySources\*, the MySources directory and all directories (one level
deep) within MySources will be searched. However, you cannot use the asterisk
as a general-purpose wild card character. For example, the use of an asterisk in
C:\MySources\*\* or C:\MySources\abc* is invalid.
You must specify the complete absolute (not relative) path name for the file in
the Search Path List. Otherwise, the Source window will not locate the source
file. Make sure that the source file you are looking for has a unique file name.
When searching for source files it is possible to load the wrong file if there is
another file with the same name in the directories specified by the search path.
The Source window always loads the first file that matches the search criteria.
Because some compilers do not include a source file suffix, you may also need to
specify the correct file suffixes in the file suffix list (examples of correct file
suffixes are: .c .cpp, and .s). The Source window will always load the first file
that matches the criteria in the file suffix list.
The logic analyzer searches for files using both lists from top to bottom.
Therefore, you should place the most likely search path or file suffix at the
beginning of the lists.
The search path lists and the suffix lists in the Source Files property page are
valid only for the current Source window. If you want to save the settings as
defaults, click Save settings as application defaults. The settings will be saved to
System Source Files property page and will be used each time you create a new
Source window.
3–98
TLA 700 Series Logic Analyzer User Manual
Source Window
Printing Source Data
You can print a hardcopy of the Source window or you can print the image to a
file. You can print a single page, a range of pages, or you can print a range of
data between two marks or cursors.
1. Go to the File menu and select Print.
2. Select Print to File, or select your printer in the window.
3. Select the print range and click OK.
When you click OK a confirmation message displays, informing you of the
approximate number of pages that will be printed.
4. Click OK again to confirm your actions.
5. To interrupt printing at any time, press ESC.
The contents of the window will be sent to the printer or to the specified file.
TLA 700 Series Logic Analyzer User Manual
3–99
Source Window
Source Window Shortcut Keys
You can use the general-purpose shortcut keys listed in Table 3–12 to move data
and cursors in the Source window. You should also refer to the discussions of
short cut keys in the online help or under the section for the individual data
windows.
The shortcut keys (also known as accelerator keys or hot keys) abide by the
following rules:
H
Arrow keys with no modifier keys scroll data.
H
Arrow keys with the Control (CTRL) key move the active cursor.
H
The Shift key increases movement by a factor of 10.
Table 3–12: Source window shortcut keys
3–100
Desired action
Key combination
Display Go To dialog box
CTRL + G
Move Cursor 1 to the center of the window
CTRL + 1
Move Cursor 2 to the center of the window
CTRL + 2
Add a mark
CTRL + K
Scroll data up 10 lines
Shift + Up arrow
Scroll data down 10 lines
Shift + Down arrow
Move active cursor up one line
CTRL + Up arrow
Move active cursor down one line
CTRL + Down arrow
Move active cursor up 10 lines
CTRL + Shift + Up arrow
Move active cursor down 10 lines
CTRL + Shift + Down arrow
TLA 700 Series Logic Analyzer User Manual
Histogram Window
Use the Histogram window to set up, capture, and display performance analysis
data from an LA module channel group, counter, or timer. You can use the
Histogram window to determine the level of activity within various functions or
subroutines, analyze how memory is used, or determine the relative execution
time of subroutines or program modules.
Histogram data is presented as a list of ranges and corresponding histogram bars
showing the distribution of the ranges. See Figure 3–63 for an example.
Figure 3–63: Histogram window
The histogram data is based on all acquisition data (All Samples) or on the data
within a defined set of ranges (Matched Samples).
TLA 700 Series Logic Analyzer User Manual
3–101
Histogram Window
Measuring Histogram Data
There are two basic ways of using the Histogram window to analyze data. One is
to provide a graphic overview of the address activity of software execution. The
other is to use counters or timers to measure specific events.
If you want to use counters or timers to measure events, you set up the counters
or timers in the Trigger window. You can then select the data source in the New
Data Window wizard when you create a Histogram window. You can also select
the data source for an existing Histogram window from the Data Source property
page as shown in Figure 3–64.
Figure 3–64: Selecting the data source for the Histogram window
Viewing Address Activity
for Channel Groups
(Range Overview)
To provide an overview of the address activity of a software routine, you define a
set of ranges (either numeric, logarithmic, or symbolic). You can set up the
Trigger window to look for data within the defined ranges. The data is processed
and displayed in the Histogram window for the current acquisition. If you set up
the logic analyzer to repetitively acquire data, the sampling errors will decrease
over time as you acquire more data. The resultant data provides a stable display
in the Histogram window where you can view the overall activity of the
software.
You can use this method of analyzing data to determine which sections of code
are being accessed or not accessed. You can also determine the overall time spent
in a routine with respect to other areas of code. Figure 3–63 is an example of
viewing address activity in a software application using symbolic ranges.
3–102
TLA 700 Series Logic Analyzer User Manual
Histogram Window
Measuring Counter or
Timer Events
(Single Event)
To measure an event, you define a starting point, a target event, a counter or a
timer, and a stopping point in the LA Trigger window. Use the Data Source
property page to select the counter or timer as the data source for your analysis.
When you acquire data, the Histogram window displays the minimum, maximum, and average value of the counter or timer data as shown in Figure 3–65.
Figure 3–65: Measuring events with the Histogram window
Creating a Histogram Window
Before creating the Histogram window you should define the channel setups and
clocking in the Setup window. You should also define your trigger program in
the Trigger window. If you want to measure an event, you should define the
trigger events and set up the appropriate counter and timer actions. If you want to
use symbols, you should make sure that you load the symbol file.
You can create a new Histogram window with the New Data Window wizard as
follows:
1. Click the New Data Window icon in the toolbar.
2. Select Histogram and click Next.
3. Select Data from an LA in the System.
TLA 700 Series Logic Analyzer User Manual
3–103
Histogram Window
4. Click Next.
5. If you want to do an overview of address groups, select Group and the
address group that you want to monitor.
6. If you want to measure an event, select Counter/Timer and the counter or
timer that you defined in the Trigger window.
7. Click Next.
8. Enter a name for the Histogram window or use the default name.
9. Click Finish.
Adjusting the Histogram Data View
There are a number of actions you can perform in the Histogram window to get
the exact view of the data that you want.
Histogram Window
Toolbar
The toolbar has shortcut buttons for common operations as shown below.
Font Size
Properties
Changing the Display Font
Size
Clearing Histogram
Counts
Stop Analyzing
Click the Font Size toolbar buttons, shown in the previous figure. You can
continue to click the toolbar buttons until the text reaches the desired size. You
can also set the font to a specific size in the Histogram Window property sheet.
Click the Clear Counts toolbar button to reset all ranges and percentages to zero.
Stopping Analysis
Click the Stop Analyzing toolbar button to stop analyzing the current acquisition. This button is inactive when there is no current acquisition in process.
Sizing Columns
Select the column label separator and drag it to change the width of a column.
Sorting Data within
Columns
3–104
Clear Counts
Sort ranges, counts, and percentages by clicking on the column labels. Click the
column label to toggle the sort between increasing and decreasing values.
TLA 700 Series Logic Analyzer User Manual
Histogram Window
Changing Histogram
Magnification
Select Scale from the View menu. Select a new magnification value from the list
and click OK. You can also click on the percentage column label and select a
magnification value.
Defining Histogram
Ranges
Ranges displayed in the Histogram window are based on the values you select in
the Ranges property page. You can define ranges as follows:
Splitting the Data Area
H
Linear generation. The ranges are divided linearly between two bounds.
H
Log generation. The ranges are divided logarithmically between two bounds.
H
Symbols. The ranges are defined by the values in a loaded symbol file. You
can use the same loaded symbol table as in other windows.
You can split the data area to compare ranges that are far away from each other
within the display. Drag the split box from the top of the horizontal scroll bar.
Customizing the Histogram Window Data Area
Use property sheets to customize data in the Histogram window. The property
sheets control aspects of the Histogram display such as ranges, bounds, font size,
color, and data source information. Click the Properties toolbar button to open
the property sheets. Then select one of the specific property sheets you are
interested in.
Here are some guidelines for using and customizing the Histogram window.
H
You can analyze live LA data or saved LA data (reference data).
H
Data is accumulated until you explicitly clear the data.
H
There is no limit to the number of symbolic ranges for histogram data.
H
You can use up to 32 bits of data in a address group.
H
You can enable or disable channel group polarity.
H
You can change colors for the foreground, background, and histogram bars
as needed.
H
You can change the data font size as necessary to view the data.
TLA 700 Series Logic Analyzer User Manual
3–105
Histogram Window
Exporting Histogram Data
Use the Export Histogram dialog box to export data from the current Histogram
window to a text file. This is a way to print a copy of the histogram data.
Figure 3–66 shows the Export Histogram dialog box.
Figure 3–66: Export Histogram dialog box
Click Options to define the format of the data in the Export Histogram Options
dialog. The data is saved in a text file with the .txt file name extension.
Use the Export Data Options dialog to customize the data for a text file. You can
specify the field delimiter to separate the columns. To export the bounds as a text
string, select Label “00–FF.” To export the bounds as two delimited numbers,
select Numbers.
To export Histogram data, follow these steps:
1. In the System window, select a Histogram window.
2. Go to the File menu and select Export Histogram.
3. In the Export Histogram dialog box, select the folder to which you want to
export data. Otherwise, leave the default of My Documents.
4. Click Options to specify any export options for the text data and then click
OK.
5. Enter a name for the exported file.
3–106
TLA 700 Series Logic Analyzer User Manual
Histogram Window
6. Specify the export range.
7. Click Save.
Figure 3–67 shows an example of an exported histogram file. The file was
viewed with WordPad.
Figure 3–67: ASCII histogram data file
Printing Histogram Data
You can print a hardcopy of the Histogram window or you can print the image to
a file. You can print a single page, a range of pages, or all pages.
1. Go to the File menu and select Print.
2. Select Print to File, or select your printer in the window.
3. Select the print range and click OK.
When you click OK, a confirmation message displays, informing you of the
approximate number of pages that will be printed.
4. Click OK again to confirm your actions.
5. To interrupt printing at any time, press ESC.
The contents of the window will be sent to the printer or to the specified file.
TLA 700 Series Logic Analyzer User Manual
3–107
Histogram Window
Histogram Window Shortcut Keys
You can use the general-purpose shortcut keys listed in Table 3–13 to move data
and cursors in the Histogram window. You should also refer to the discussions of
short cut keys in the online help or under the section for the individual data
windows.
The shortcut keys (also known as accelerator keys or hot keys) abide by the
following rules:
H
Arrow keys with no modifier keys scroll data.
H
The Shift key increases movement by a factor of 10.
Table 3–13: Histogram window shortcut keys
3–108
Desired action
Key combination
Scroll data up 10 ranges
Shift + Up arrow
Scroll data down 10 ranges
Shift + Down arrow
TLA 700 Series Logic Analyzer User Manual
Appendices
Appendix A: Specifications
This chapter lists the specifications for the logic analyzer and its modules. The
first section lists specifications that are common to the mainframes or modules.
The following sections list specifications that are specific to individual logic
analyzer components.
Characteristic Tables
All specifications are guaranteed unless noted Typical. Typical characteristics
describe typical or average performance and provide useful reference information. Specifications that are marked with the n symbol are checked directly (or
indirectly) in the TLA 700 Series Performance Verification and Adjustment
Technical Reference Manual. The specifications apply to all versions of the logic
analyzer mainframe or module unless otherwise noted.
For mainframes and modules, the performance limits in this specification are
valid with these conditions:
H
The logic analyzer must be in an environment with temperature, altitude,
humidity, and vibration within the operating limits described in these
specifications.
H
The logic analyzer must have had a warm-up period of at least 30 minutes.
For modules, the performance limits in this specification are valid with these
conditions:
H
The modules must be installed in a TLA 700 Series Logic Analyzer
Mainframe.
H
The module must have been calibrated/adjusted at an ambient temperature
between +20_C and +30_C.
H
The module must have had its signal-path-compensation routine (self calibration) last executed after at least a 30 minute warm-up period.
H
After the warm-up period, the DSO module must have had its signal-pathcompensation routine (self cal) last executed at an ambient temperature
within ±5_C of the current ambient temperature.
TLA 700 Series Logic Analyzer User Manual
A–1
Appendix A: Specifications
Table A–1: Atmospheric characteristics (mainframes and modules)
Characteristic
Description
Temperature:
Operating and Non-Operating
Operating (no media in floppy disk drive)
+5_C to +50_C, 15_C/hour maximum gradient, non-condensing (derated 1_C per 1000 feet
above 5000 foot altitude)
Non-operating (no media in floppy disk drive)
–20_C to +60_C, 15_C/hour maximum gradient, non-condensing.
Relative Humidity:
Operating and Non-Operating
Operating (no media in floppy disk drive)
20% to 80% relative humidity, non-condensing. Maximum wet bulb temperature: +29_C
(derates relative humidity to approximately 22% at +50_C).
Non-operating (no media in floppy disk drive)
8% to 80% relative humidity, non-condensing. Maximum wet bulb temperature: +29_C (derates
relative humidity to approximately 22% at +50_C).
Altitude:
Operating and Non-Operating
Operating:
To 10,000 feet (3040 meters), (derated 1_C per 1000 feet (305 meters) above 5000 feet
(1524 meters) altitude)
Non-operating:
40,000 feet (12190 meters).
A–2
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
Table A–2: Backplane interface (portable and benchtop mainframes)
Characteristic
Description
Slots
Portable mainframe
4
Benchtop mainframe
13
n CLK10 Frequency
10 MHz ±100 PPM
Relative Time Correlation Error1,2 (Typical)
LA to LA “MagniVu” data
2 ns
LA to LA “normal” data utilizing an internal clock3
1 LA sample – 0.5 ns
LA to LA “normal” data utilizing an external clock
2 ns
LA “MagniVu” to DSO data
3 ns
LA to DSO “normal” data utilizing an internal clock3,4
1 LA sample + 1 ns
LA to DSO “normal” data utilizing an external clock4
3 ns
DSO to DSO4
3 ns
System Trigger and External Signal Input Latencies5,6 (Typical)
External System Trigger Input to LA Probe Tip7
–271 ns
External Signal Input to LA Probe Tip via Signal 3, 48
–212 ns + Clk
External Signal Input to LA Probe Tip via Signal 1, 28, 9
–208 ns + Clk
External System Trigger Input to DSO Probe Tip7
–27 ns
System Trigger and External Signal Output Latencies6 (Typical)
LA Probe Tip to External System Trigger Out3
380 ns + SMPL
LA Probe Tip to External Signal Out via Signal 3, 43
OR function
371 ns + SMPL
AND function
383 ns + SMPL
LA Probe Tip to External Signal Out via Signal 1, 23,9
normal function
381 ns + SMPL
inverted logic on backplane
384 ns + SMPL
DSO Probe Tip to External System Trigger Out
70 ns
DSO Probe Tip to External Signal Out via Signal 3, 4
OR function
68 ns
AND function
78 ns
DSO Probe Tip to External Signal Out via Signal 1, 29
normal function
71 ns
inverted logic on backplane
71 ns
TLA 700 Series Logic Analyzer User Manual
A–3
Appendix A: Specifications
Table A–2: Backplane interface (portable and benchtop mainframes) (Cont.)
Characteristic
Description
Inter-Module Latencies6 (Typical)
LA to DSO Inter-module System Trigger3,7
358 ns + SMPL
LA to LA Inter-module System Trigger3,7
68 ns + SMPL
LA to DSO Inter-Module ARM3
360 ns + SMPL
LA to LA Inter-Module ARM3,8
108 ns + SMPL + Clk
LA to LA Inter-Module via Signal 1, 23,8, 9
120 ns + SMPL + Clk
LA to LA Inter-Module via Signal 3, 43,8
116 ns + SMPL + Clk
DSO to DSO Inter-module System Trigger7
50 ns
DSO to LA Inter-module System Trigger7
–236 ns
DSO to LA Inter-Module ARM8
–192 ns + Clk
DSO to DSO Inter-Module ARM
59 ns
DSO to LA Inter-Module via Signal 1, 28, 9
–179 ns + Clk
DSO to LA Inter-Module via Signal 3, 48
–184 ns + Clk
1
Includes typical jitter, slot-to-slot skew, and probe-to-probe variations to provide a “typical” number for the measurement.
Assumes standard accessory probes are utilized.
2
For time intervals longer than 1 ms between modules, add 0.01% of the difference between the absolute time measurements to the relative time correlation error to account for the inaccuracy of the CLK10 source.
3
SMPL represents the time from the event at the probe tip inputs to the next valid data sample of the LA module. In the
Normal Internal clock mode, this represents the delta time to the next sample clock. In the MagniVu Internal clock mode,
this represents 500 ps or less. In the External clock mode, this represents the time to the next master clock generated by
the setup of the clocking state machine, the system-under-test supplied clocks, and the qualification data.
4
The DSO module time correlation is measured at the maximum sample rate on one channel only.
5
All system trigger and external signal input latencies are measured from a falling-edge transition (active true low) with
signals measured in the wired-OR configuration.
6
Latencies are based on typical portable mainframe configurations consisting of two LA modules or an LA module plus a
DSO module. Latencies are system-configuration-dependent and may vary slightly with module loading.
7
In the Waveform window, triggers are always marked immediately except when delayed to the first sample. In the Listing
window, triggers are always marked on the next sample period following their occurrence.
8
“Clk” represents the time to the next master clock at the destination logic analyzer. In the asynchronous (or internal)
clock mode, this represents the delta time to the next sample clock beyond the minimum async rate of 4 ns. In the
synchronous (or external) clock mode, this represents the time to the next master clock generated by the setup of the
clocking state machine and the supplied system under test clocks and qualification data.
9
Signals 1 and 2 (ECLTRG0, 1) are limited to a “broadcast” mode of operation, where only one source is allowed to drive
the signal node at any one time. That single source may be utilized to drive any combination of destinations.
A–4
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
Table A–3: External signal interface (portable and benchtop mainframes)
Characteristic
Description
System Trigger Input
TTL compatible input via rear panel mounted BNC connectors (portable mainframe) or front panel
mounted SMB connectors (benchtop mainframe)
Input Levels
VIH
VIL
TTL compatible input.
≥ 2.0 V
≤ 0.8 V
Input Mode
Falling edge sensitive, latched (active low)
Minimum Pulse Width
12 ns
Active Period
Accepts system triggers during valid acquisition periods via real-time gating, resets system trigger
input latch between valid acquisition periods
Maximum Input Voltage
0 to +5 Volt peak
External Signal Input
TTL compatible input via rear panel mounted BNC connectors (portable mainframe) or front panel
mounted SMB connectors (benchtop mainframe)
Input Destination
Signal 1, 2, 3, 4
Input Levels
VIH
VIL
TTL compatible input.
≥ 2.0 V
≤ 0.8 V
Input Mode
Active (true) low, level sensitive
Input Bandwidth1
Signal 1, 2
Signal 3, 4
50 MHz square wave minimum
10 MHz square wave minimum
Active Period
Accepts signals during valid acquisition periods via real-time gating
Maximum Input Voltage
0 to +5 Volt peak
System Trigger Output
TTL compatible output via rear panel mounted BNC connectors (portable mainframe) or front
panel mounted SMB connectors (benchtop mainframe)
Source Mode
Active (true) low, falling edge latched
Active Period
Outputs system trigger state during valid acquisition period, resets system trigger output to false
state between valid acquisitions
Output Levels
VOH
50 Ohm back terminated TTL-compatible output
≥4 V into open circuit
≥ 2 V into 50 Ohm to ground
VOL
Output Protection
≥ 0.7 V sinking 10 ma
Short-circuit protected (to ground)
TLA 700 Series Logic Analyzer User Manual
A–5
Appendix A: Specifications
Table A–3: External signal interface (portable and benchtop mainframes) (Cont.)
Characteristic
Description
External Signal Output
TTL compatible outputs via rear panel mounted BNC connectors (portable mainframe) or front
panel mounted SMB connectors (benchtop mainframe)
Source Selection
Signal 1, 2, 3, 4, or 10 MHz clock
Output Modes
Level Sensitive
User definable
Active (true) low or active (true) high
Output Levels
VOH
50 Ohm back terminated TTL output
≥ 4 V into open circuit
≥ 2 V into 50 Ohm to ground
VOL
≤ 0.7 V sinking 10 ma
Output Bandwidth2
Signal 1, 2
Signal 3, 4
Active Period
50 MHz square wave minimum
10 MHz square wave minimum
Outputs signals during valid acquisition periods, resets signals to false state between valid
acquisitions
Outputs 10 MHz clock continuously
Output Protection
Short-circuit protected (to ground).
Intermodule Signal Line
Bandwidth
Signal 1, 2 (ECLTRG 0,1)
Signal 3, 4 (ECLTRG 0,1)
Minimum bandwidth up to which the intermodule signals are specified to operate correctly
50 MHz square wave minimum
10 MHz square wave minimum
1
The Input Bandwidth specification only applies to signals to the modules; it does not apply to signals applied to the
External Signal Input and sent back to the External Signal Output.
2
The Output Bandwidth specification only applies to signals from the modules; it does not apply to signals applied to the
External Signal Input and sent back to the External Signal Output.
A–6
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
Table A–4: Certifications and compliances: TLA 704 Color Portable Mainframe1 and TLA 711 Color Benchtop
Mainframe1
EC Declaration of Conformity –
EMC
Meets intent of Directive 89/336/EEC for Electromagnetic Compatibility. Compliance was
demonstrated to the following specifications as listed in the Official Journal of the European
Communities:
EN 55011
Class A Radiated and Conducted Emissions
EN 50081-1 Emissions:
EN 60555-2
AC Power Line Harmonic Emissions
EN 50082-1 Immunity:
IEC 801-2
IEC 801-3
IEC 801-4
IEC 801-5
Electrostatic Discharge Immunity
RF Electromagnetic Field Immunity
Electrical Fast Transient/Burst Immunity
Power Line Surge Immunity
1
EC Declaration of Conformity –
Low Voltage
The following modules meet the intent of EMC Directive 89/336/EEC when they are used with
the above named mainframes:
TLA 700 Series Logic Analyzer Modules (TLA 7L1, TLA 7L2, TLA 7L3, TLA 7L4, TLA 7M1,
TLA 7M2, TLA 7M3, TLA 7M4)
TLA 700 Series Digitizing Oscilloscope Modules (TLA 7D1, TLA 7D2, TLA 7E1, TLA 7E2)
Compliance was demonstrated to the following specification as listed in the Official Journal of the
European Communities:
Low Voltage Directive 73/23/EEC
EN 61010-1:/A2 1995
Approvals
Safety requirements for electrical equipment for measurement,
control, and laboratory use
UL3111-1 – Standard for electrical measuring and test equipment
CAN/CSA C22.2 No. 1010.1 – Safety requirements for electrical equipment for measurement,
control and laboratory use
Installation Category Descriptions
Conditions of Approval
Terminals on this product may have different installation category designations. The installation
categories are:
CAT III
Distribution-level mains (usually permanently connected). Equipment at this level is
typically in a fixed industrial location
CAT II
Local-level mains (wall sockets). Equipment at this level includes appliances, portable
tools, and similar products. Equipment is usually cord-connected
CAT I
Secondary (signal level) or battery operated circuits of electronic equipment
Safety Certifications/Compliances are made for the following conditions:
Temperature (operation): +5_C to +40_C
Altitude (maximum operation): 2000 meters
IEC Characteristics
Equipment type:
Test and Measuring
Installation Category II
Pollution Degree 2
Safety Class I
TLA 700 Series Logic Analyzer User Manual
A–7
Appendix A: Specifications
TLA 704 Color Portable Mainframe Characteristics
Table A–5: Portable mainframe internal controller
Characteristic
Description
Processor
Intel 133 MHz Pentium PC-AT configuration, with an Intel 82430HX (Triton II) chip set
Main Memory
EDO DRAM
Style
Two 72-pin SIMMs, gold-plated
Loading
Symmetric, 2-SIMM minimum (64 bits)
Speed
60 ns
Installed Configurations
16-MByte minimum, 32-MByte maximum
Cache Memory
256 Kbyte, level 2 (L2) write-back cache
Flash BIOS
512 Kbyte
Real-Time Clock and CMOS Setups
NVRAM (Typical)
Real-Time clock/calendar, with typical 10-year life. Standard and advanced PC CMOS setups:
see BIOS specification. Year 2000 compliant.
Floppy Disk Drive
Standard 3.5 inch, 1.44 Mbyte, double-sided PC-compatible high-density floppy disk drive
Hard Disk Drive
Standard PC-compatible with ATA/Enhanced Integrated Device Electronics (EIDE) interface
Capacity
MIN configuration: 1.4 GByte
MAX configuration: 2.1 GByte
Subject to change; these are the storage capacities valid at product introduction
Table A–6: Portable mainframe display system
Characteristic
Description
Classification
Standard PC graphics accelerator technology (bitBLT-based); capable of supporting both internal
color LCD display and external color SVGA/XGA monitor
Display Memory
DRAM-based frame-buffer memory
Size
1 MByte
Width
32-bit
Display Selection
Hardware sense of external SVGA monitor during BIOS boot sequence; defaults to internal color
LCD display; automatically switches to external SVGA monitor, if attached
Dual (simultaneous) display of external SVGA monitor and internal color LCD is possible via
special “simulscan” CMOS setup, as long as internal and external displays operate at same
resolution (limited to 640x480 on current TFT LCD) and display rates
Dynamic Display Configuration 1 (DDC1) support for external SVGA monitor is provided
External Display Drive
A–8
1 SVGA/XGA-compatible analog output port
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
Table A–6: Portable mainframe display system (Cont.)
Characteristic
Display Size
Description
User selected via Windows 95
Resolution (Pixels)
640x480
640x480
640x480
800x600
800x600
1024x768
Colors
256
64K
16.8M
256
64K
256
DDC1
yes
yes
no
yes
yes
yes
Internal Display
Classification
Thin Film Transistor (TFT) 10.4 inch active-matrix color LCD display; CCFL backlight; intensity
controllable via software
Resolution
640 pixels horizontal by 480 pixels
Color Scale
262,144 colors (6-bit RGB)
Table A–7: Portable mainframe front-panel interface
Characteristic
Description
QWERTY Keypad
ASCII keypad to support naming of files, traces, and keyboard equivalents of pointing device
inputs for menus
HEX Keypad
HEX keypad supporting standard DSO and LA entry functions
Special Function Knobs
Various functions
Integrated Pointing Device
GlidePoint touchpad
Mouse Port
PS/2 compatible mouse port utilizing a mini-DIN connector
Keyboard Port
PS/2 compatible keyboard port utilizing a mini-DIN connector
Table A–8: Portable mainframe rear-panel interface
Characteristic
Description
Parallel Interface Port (LPT)
36-pin high-density connector supports standard Centronics mode, Enhanced Parallel Port
(EPP), or Microsoft high-speed mode (ECP)
Serial Interface Port (COM A)
9-pin male sub-D connector to support RS-232 serial port.
SVGA Output Port (SVGA OUT)
15-pin sub-D SVGA connector
Type I and II PC Card Port
Standard Type I and II PC-compatible PC card slot
Type I, II, and III PC Card Port
Standard Type I, II, and III PC-compatible PC card slot
TLA 700 Series Logic Analyzer User Manual
A–9
Appendix A: Specifications
Table A–9: Portable mainframe AC power source
Characteristic
Description
Source Voltage and Frequency
90–250 VRMS, 45–66 Hertz, continuous range CAT II
100–132 VRMS, 360–440 Hertz, continuous range CAT II
Fuse Rating
90 V - 250 V Operation
(159-0046-00)
UL198/CSA C22.2
0.25 in × 1.25 in, Fast Blow, 8 A, 250 V
90 V - 250 V Operation
(159-0381-00)
IEC 127/Sheet 1
5 mm × 20 mm, Fast Blow, 6.3 A, 250 V
Maximum Power Consumption
600 W line power maximum
Steady-State Input Current
6 ARMS maximum
Inrush Surge Current
70 A maximum
Power Factor Correction
Yes
On/Standby Switch and Indicator
Front Panel On/Standby switch, with LED indicator located next to switch
The power cord provides main power disconnect.
Table A–10: Portable mainframe secondary power
Characteristic
Description
n DC Voltage Regulation
(Combined System, voltage available at each slot)
A–10
Voltage
Vmin,
Vnom,
Vmax
+24 V
23.28 V, 24.24 V, 25.20 V
+12 V
11.64 V, 12.12 V, 12.60 V
+5 V
4.875 V, 5.063 V, 5.250 V
–2 V
–2.10 V, –2.00 V, –1.90 V
–5.2 V
–5.460 V, –5.252 V, –5.044 V
–12 V
–12.60 V, –12.12 V, –11.64 V
–24 V
–25.20 V, –24.24 V, –23.28 V
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
Table A–11: Portable mainframe cooling
Characteristic
Description
Cooling System
Forced air circulation (negative pressurization) utilizing six fans operating in parallel
Cooling Clearance
2 inches (51 mm), sides and rear; unit should be operated on a flat, unobstructed surface
Table A–12: Portable mainframe mechanical
Characteristic
Description
Overall Dimensions
(See Figure A–1 for overall chassis dimensions)
Height (with feet)
9.25 in (235 mm)
Width
17.0 in (432 mm)
Depth
17.5 in (445 mm)
Weight
Shipping configuration
30 lbs 12 oz (13.9 kg) with no modules installed, 2 dual-wide slot covers, and empty pouch
60 lbs 13 oz (27.58 kg) minimum configuration (no modules), with all standard accessories
86 lbs 9 oz (39.26 kg) full configuration, with 2 TLA 7M4 modules and standard accessories
(including probes)
17.0 in
(432 mm)
17.5 in
(445 mm)
9.25 in
(235 mm)
Figure A–1: Front and side views of TLA 704 Color Portable Mainframe
TLA 700 Series Logic Analyzer User Manual
A–11
Appendix A: Specifications
TLA 711 Color Benchtop Chassis Characteristics
Table A–13: Benchtop chassis AC power source
Characteristic
Description
Source Voltage
90–250 VRMS, 45–66 Hertz, continuous range CAT II
100–132 VRMS, 360–440 Hertz, continuous range CAT II
Maximum Power Consumption
1350 W line power (the maximum power consumed by a fully loaded 13-slot instrument)
Fuse Rating
(Current and voltage ratings and
type of fuse used to fuse the source
line voltage)
90 V – 132 VACRMS Operation
High-power/Low Line
(159-0379-00)
Safety: UL198G/CSA C22.2,
Size: 0.25 in × 1.25 in,
Style: Slow acting,
Rating: 20 A/250 V
103 V – 250 VACRMS Operation
(159-0256-00)
Safety: UL198G/CSA C22.2,
Size: 0.25 in × 1.25 in,
Style: No. 59/Fast acting,
Rating: 15 A/250 V
207 V – 250 VACRMS Operation
(159-0381-00)
Safety: IEC 127/Sheet 1,
Size: 5 mm × 20 mm,
Style: Fast acting “F”, high-breaking capacity,
Rating: 6.3 A/250 V
Inrush Surge Current
70 A maximum
Steady State Input Current
15 ARMS maximum at 90 VACRMS
6.3 ARMS maximum at 207 VACRMS
Power Factor Correction
Yes
ON/Standby Switch and Indicator
Front Panel On/Standby switch with integral power indicator
Table A–14: Benchtop chassis secondary power
Characteristic
Description
n DC Voltage Regulation
(Combined System, voltage available at each slot)
A–12
Voltage
Vmin,
Vnom,
Vmax
+24 V
23.28 V, 24.24 V, 25.20 V
+12 V
11.64 V, 12.12 V, 12.60 V
+5 V
4.875 V, 5.063 V, 5.250 V
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
Table A–14: Benchtop chassis secondary power (Cont.)
Characteristic
Description
–2 V
–2.10 V, –2.00 V, –1.90 V
–5.2 V
–5.460 V, –5.252 V, –5.044 V
–12 V
–12.60 V, –12.12 V, –11.64 V
–24 V
–25.20 V, –24.24 V, –23.28 V
Table A–15: Benchtop chassis cooling
Characteristic
Description
Cooling System
Forced air circulation system (positive pressurization) utilizing a single low-noise centripetal
(squirrel cage) blower configuration with no removable filters
Blower Speed Control
Rear panel switch selects between full speed and variable speed. Slot exhaust temperature and
ambient air temperature are monitored such that a constant delta temperature is maintained
across the module with the highest exit air temperature at the minimum operational blower speed
Slot Activation
Installing a module activates the cooling for the corresponding occupied slots by opening the air flow
shutter mechanism. Optimizes cooling efficiency by only applying airflow to modules that are installed
Delta Temperature Readout
Sensitivity
100 mV/°C with 0°C corresponding to 0 V output
Temperature Sense Range
–10°C to +90°C, Delta temperature ≤ 50°C
Clearance
2 in (51 mm), rear, top, and sides of chassis
Table A–16: Benchtop chassis mechanical
Characteristic
Description
Overall Dimensions
(See Figure A–2 for overall chassis dimensions)
Standard Chassis
Height (with feet)
14.25 in (362.0 mm)
Width
16.75 in (425.5 mm)
Depth
26.5 in (673.1 mm)
Chassis with Rackmount
Height
14.0 in (355.6 mm)
Width
18.9 in (480.1 mm)
Depth
29.4 in to 34.4 in (746.8 mm to 873.8 mm)
Weight
Minimum configuration with benchtop controller and slot covers
TLA 700 Series Logic Analyzer User Manual
62 lbs 2 oz (28.18 kg)
A–13
Appendix A: Specifications
Table A–16: Benchtop chassis mechanical (Cont.)
Characteristic
Description
Typical configuration with 2 LA, 1 DSO, and controller
77 lbs 14 oz (35.32 kg)
Shipping configuration
118 lbs (53.52 kg) minimum configuration (no modules) with
benchtop controller and all standard accessories
175 lbs (79.38 kg) fully configured with benchtop controller,
3 LA modules, 2 DSO modules, and all standard accessories
Rackmount kit adder
20 lbs (9.1 kg)
Module Size
13 plug-in slots
16.75 in
(425.5 mm)
26.5 in
(673.1 mm)
14.25 in
(362.0 mm)
Figure A–2: Front view and side view of standard Benchtop chassis
18.9 in
(480.1 mm)
29.4 in (746.7 mm) Min to
34.4 in (873.8 mm) Max
14.0 in
(355.6 mm)
Figure A–3: Front view and side view of Benchtop chassis with Rackmount Option
A–14
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
TLA 711 Color Benchtop Controller Characteristics
Table A–17: Benchtop controller characteristics
Characteristic
Description
Processor
Intel Pentium 133 MHz PC-AT configuration with an Intel 82430HX (Triton II) chip-set
Main Memory
EDO DRAM
Style
2-72 pin SIMMs, gold plated
Loading
Symmetrical, 2-SIMM minimum (64-Bits)
Speed
60 ns
Installed Configuration
16 MByte minimum configuration
32 MByte maximum configuration
Cache Memory
256 Kbyte, level 2 (L2) write-back cache
Flash BIOS
512 Kbyte
Real-Time Clock and CMOS Setups NVRAM
(Typical)
Real-Time clock/calendar, with typical 10-year life. Standard and advanced PC CMOS
setups: see BIOS specification. Year 2000 compliant.
Floppy Disk Drive
Standard 3.5 inch, 1.44 Mbyte, double-sided, PC-compatible high-density floppy disk
drive
Hard Disk Drive
Standard PC-compatible with ATA/Enhanced Integrated Device Electronics (EIDE)
interface
Capacity
MIN configuration: 1.4 GByte
MAX configuration: 2.1 GByte
Subject to change; these are the storage capacities valid at product introduction
Display Classification
Standard PC graphics accelerator technology (bitBLT based) capable of driving
external color VGA, SVGA, or XGA monitors
Display Memory
DRAM based frame-buffer memory.
Width
32 Bit
Size
1 MByte
Display Drive
Display Size
One VGA, SVGA, or XGA compatible analog output port
User selected via Windows 95.
Resolution (Pixels)
640x480
640x480
640x480
800x600
800x600
1024x768
Colors
256
64 K
16.8 M
256
64 K
256
DDC1
yes
yes
no
yes
yes
yes
Mouse Port
Front panel mounted PS2 compatible mouse port utilizing a mini-DIN connector
Keyboard Port
Front panel mounted PS2 compatible keyboard port utilizing a mini-DIN connector
TLA 700 Series Logic Analyzer User Manual
A–15
Appendix A: Specifications
Table A–17: Benchtop controller characteristics (Cont.)
Characteristic
Description
Parallel Interface Port (LPT)
36-pin high-density connector supports standard Centronics mode, Enhanced Parallel
Port (EPP), or Microsoft high-speed mode (ECP)
Serial Interface Port (COM)
The serial port utilizing a 9-pin male sub-D connector to support an RS232 serial port
SVGA Output Port (SVGA)
The SVGA port utilizing a 15-pin sub-D SVGA connector
Type I and II PC Card Port
Standard Type I and II PC compatible PC card slot
Type I, II, and III PC Card Port
Standard Type I, II, and III PC compatible PC card slot
Table A–18: Benchtop controller mechanical characteristics
Characteristic
Description
Weight
5 lb. 3 oz. (2.34 kg)
Size
Standard dual-wide, VXI C-size enclosure
Overall dimensions
Height
10.32 in (262 mm)
Width
2.39 in (61 mm)
Depth
14.7 in (373 mm)
A–16
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
TLA 700 Series Logic Analyzer Module Characteristics
Table A–19: LA module channel width and depth
Characteristic
Description
Number of channels
Product
Channels
TLA 7L1 and TLA 7M1
32 data and 2 clock
TLA 7L2 and TLA 7M2
64 data and 4 clock
TLA 7L3 and TLA 7M3
96 data, 4 clock, and 2 qualifier
TLA 7L4 and TLA 7M4
128 data, 4 clock, and 4 qualifier
Product
Memory depth
TLA 7L1, TLA 7L2, TLA 7L3, TLA 7L4
32 K1
TLA 7M1, TLA 7M2 ,TLA 7M3, TLA 7M4
512 K
Acquisition memory depth
1
PowerFlex configurable to 128 K
Table A–20: LA module clocking
Characteristic
Description
Asynchronous clocking
n Internal sampling period1
4 ns to 50 ms in a 1–2–5 sequence
n
Channel-to-channel skew + sample uncertainty
Minimum recognizable word2
(across all channels)
Example: for a P6417 Probe and a 4 ns sample period = 1.6 ns + 4 ns = 5.6 ns
Synchronous clocking
Number of clock channels3
Number of qualifier channels
Product
Clock channels
TLA 7L1 and TLA 7M1
2
TLA 7L2 and TLA 7M2
4
TLA 7L3 and TLA 7M3
4
TLA 7L4 and TLA 7M4
4
Product
Qualifier channels
TLA 7L1 and TLA 7M1
0
TLA 7L2 and TLA 7M2
0
TLA 7L3 and TLA 7M3
2
TLA 7L4 and TLA 7M4
4
TLA 700 Series Logic Analyzer User Manual
A–17
Appendix A: Specifications
Table A–20: LA module clocking (Cont.)
Characteristic
Description
n Setup and hold window size
(data and qualifiers)
Maximum window size = Maximum channel-to-channel skew + (2 x sample
uncertainty) + 0.4 ns
Maximum setup time = User interface setup time + 0.6 ns
Maximum hold time = User interface hold time + 0.4 ns
Max. setup time for slave module of merged pair = User Interface setup time + 0.8 ns
Max. hold time for slave module of merged pair = User Interface hold time + 0.7 ns
Example: for P6417 Probe and user interface setup & hold of 2.0/0.0 typical
Maximum setup time = 2.0 ns + 0.6 ns = 2.6 ns
Maximum hold time = 0.0 ns + 0.4 ns = 0.4 ns
Setup and hold window size (data and
qualifiers) (Typical)
Channel-to-channel skew (typical) + (2 x sample uncertainty)
Setup and hold window range
The setup and hold window can be moved for each channel group from +8.5 ns (Ts) to
–7.0 ns (Ts) in 0.5 ns steps (setup time). Hold time follows the setup time by the setup
and hold window size.
n Maximum synchronous clock rate4
200 MHz in full speed mode (5 ns minimum between active clock edges)
Example: for P6417 Probe = 1 ns + (2 x 500 ps) = 2 ns
100 MHz in half speed mode (10 ns minimum between active clock edges)
Demux clocking
Demux Channels
(TLA 7L3 ,TLA 7L4, TLA 7M3, TLA 7M4)
Channels multiplex as follows:
A3(7:0) to
D3(7:0)
A2(7:0) to
D2(7:0)
A1(7:0) to
D1(7:0)
A0(7:0) to
D0(7:0)
(TLA 7L1, TLA 7L2, TLA 7M1, TLA 7M2)
Channels multiplex as follows:
A3(7:0) to
C3(7:0)
A2(7:0) to
C2(7:0)
A1(7:0) to
D1(7:0) TLA 7L2 and TLA 7M2 only
A0(7:0) to
D0(7:0) TLA 7L2 and TLA 7M2 only
Time between DeMux clock edges4
(Typical)
5 ns minimum between DeMux clock edges in full-speed mode
10 ns minimum between DeMux clock edges in half-speed mode
Time between DeMux store clock edges4
(Typical)
10 ns minimum between DeMux master clock edges in full-speed mode
20 ns minimum between DeMux master clock edges in half-speed mode
Clocking state machine
Pipeline delays
Each channel group can be programmed with a pipeline delay of 0 through 3 active
clock edges.
1
It is possible to use storage control and only store data when it has changed (transitional storage).
2
Applies to asynchronous clocking only. Setup and hold window specification applies to synchronous clocking only.
3
Any or all of the clock channels may be enabled. For an enabled clock channel, either the rising, falling, or both edges
can be selected as the active clock edges. The clock channels are stored.
4
Full and half speed modes are controlled by PowerFlex options and upgrade kits.
A–18
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
Table A–21: LA module trigger system
Characteristic
Description
Triggering Resources
Word/Range recognizers
16 word recognizers. The word recognizers can be combined to form full width, double
bounded, range recognizers. The following selections are available:
16 word recognizers
13 word recognizers
10 word recognizers
7 word recognizers
4 word recognizers
Range recognizer channel order
0 range recognizers
1 range recognizer
2 range recognizers
3 range recognizers
4 range recognizers
From most-significant probe group to least-significant probe group: C3 C2 C1 C0 E3
E2 E1 E0 A3 A2 D3 D2 A1 A0 D1 D0 Q3 Q2 Q1 Q0 CK3 CK2 CK1 CK0
Missing channels for modules with fewer than 136 channels are omitted. When
merged, the range recognition extends across the two modules; the master1 module
contains the most-significant groups.
Glitch detector2,3
Each channel group can be enabled to detect a glitch
Minimum detectable glitch pulse width
(Typical)
2.0 ns (single channel with P6417 probe)
Setup and hold violation detector2,4
Each channel group can be enabled to detect a setup and hold violation. The range is
from 8 ns before the clock edge to 8 ns after the clock edge. The range can be
selected in 0.5 ns increments. The setup and hold violation of each window can be
individually programmed.
Transition detector2, 5
Each channel group can be enabled or disabled to detect a transition between the
current valid data sample and the previous valid data sample.
Counter/Timers6, 7
2 counter/timers, 51 bits wide, can be clocked up to 250 MHz.
Maximum count is 251
Maximum time is 9.0076 seconds or 104 days
Signal In 1
A backplane input signal
Signal In 2
A backplane input signal
Trigger In
A backplane input signal that causes the main acquisition and the MagniVu acquisition
to trigger if they are not already triggered
Active trigger resources8
16 maximum (excluding counter/timers)
Trigger States
16
n Trigger State sequence rate
Same rate as valid data samples received, 250 MHz maximum
Trigger Machine Actions
Main acquisition trigger
Triggers the main acquisition memory
Main trigger position
Trigger position is programmable to any data sample (4 ns boundaries)
Increment counter
Either of the two counter/timers used as counters can be incremented.
Start/Stop timer
Either of the two counter/timers used as timers can be started or stopped.
TLA 700 Series Logic Analyzer User Manual
A–19
Appendix A: Specifications
Table A–21: LA module trigger system (Cont.)
Characteristic
Description
Reset counter/timer
Either of the two counter/timers can be reset. When a counter/timer used as a timer
and is reset, the timer continues in the started or stopped state that it was in prior to
the reset.
Signal out
A signal sent to the backplane to be used by other modules
Trigger out
A trigger out signal sent to the backplane to trigger other modules
Storage Control
Global storage
Storage is allowed only when a specific condition is met. This condition can use any of
the trigger machine resources except for the counter/timers. Storage commands
defined in the current trigger state will override the global storage control.
Global storage can be used to start the acquisition with storage initially turned on
(default) or turned off.
By event
Storage can be turned on or off; only the current sample can be stored. The event
storage control overrides any global storage commands.
Block storage9
When enabled, 31 samples are stored before and after the valid sample.
Glitch violation storage
The acquisition memory can be enabled to store glitch violation information with each
data sample when asynchronous clocking is used. The probe data storage size is
reduced by one half (the other half holds the violation information). The fastest
asynchronous clocking rate is reduced to 10 ns.
1
For merged modules, the master module is the module installed in the lower-numbered slot.
2
Each use of a glitch detector, setup and hold violation detector, or transition detector requires a trade-off of one word
recognizer resource.
3
Any glitch is subject to pulse width variation of up to the channel-to-channel skew specification + 0.5 ns.
4
Any setup value is subject to variation of up to 1.6 ns; any hold value is subject to variation of up to 1.4 ns.
5
This mode can be used to create transitional storage selections where all channels are enabled.
6
Counters and timers can be set, reset, or tested and have zero reset latency.
7
Timers can be tested with TLA 7Lx and TLA 7Mx Modules with serial numbers B020000 and higher and TLA 700 Series
Software Version 1.10 and higher.
8
Word recognizers are traded off one-by-one as Signal In 1, Signal In 2, glitch detection, setup and hold detection, or
transition detection resources are added.
9
Block storage is disallowed when glitch storage or setup and hold violation is enabled.
A–20
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
Table A–22: LA module input parameters (with P6417 Probe)
Characteristic
Description
n Threshold Accuracy
±100 mV
Threshold range and step size
Setable from +5 V to –2 V in 50 mV steps
Threshold channel selection
16 threshold groups assigned to channels. Each probe has two threshold settings, one
for the clock/qualifier channel and one for the data channels.
n Channel-to-channel skew
≤ 1.6 ns maximum (When merged, add 0.5 ns for the slave module.)
Channel-to-channel skew (Typical)
≤ 1.0 ns typical (When merged, add 0.3 ns for the slave module.)
Sample uncertainty
Asynchronous:
Sample period
Synchronous:
500 ps
Probe input resistance (Typical)
20 kW
Probe input capacitance (Typical)
2 pF maximum
Minimum slew rate (Typical)
0.2 V/ns
Maximum operating signal
6.5 Vp-p
–3.5 V absolute input voltage minimum
6.5 V absolute input voltage maximum
Probe overdrive
±250 mV or ±25% of signal swing minimum required beyond threshold, whichever is
greater
±4 V maximum beyond threshold
Maximum nondestructive input signal to probe
±15 V
Minimum input pulse width signal
(single channel) (Typical)
2 ns
Delay time from probe tip to input probe
connector (Typical)
7.33 ns
Table A–23: LA module MagniVu feature
Characteristic
Description
MagniVu memory depth
2016 samples per channel
MagniVu sampling period
Data is asynchronously sampled and stored every 500 ps in a separate high resolution
memory.
TLA 700 Series Logic Analyzer User Manual
A–21
Appendix A: Specifications
Table A–24: Merged LA modules
Characteristic
Description
Number of modules that can be merged
together
Two adjacent modules regardless of channel widths and memory depths (TLA 7L3,
TLA 7L4, TLA 7M3, TLA 7M4 only)
Number channels after merge
The sum of the data channels of both modules plus the CLK/QUAL channels (active
clocks for the merge system) of the master module plus the CLK/QUAL channels
(nonactive stored clock channels to the merge system)
Merge system acquisition depth
Channel depth is equal to the smaller depth of the two modules.
Number of clock and qualifier channels after
merge
Same number of clock and qualifier channels on the master module. The clock and
qualifier channels on the slave module have no effect on clocking and are only stored.
Merge system triggering resources
Triggering resources are the same as a single module except that the widths of the
word/range recognizers, setup and hold violation detector, glitch detector, and
transition detector are increased to the merged channel width.
Table A–25: LA module data handling
Characteristic
Description
Nonvolatile memory retention time (Typical)
Battery is integral to the NVRAM. Battery life is > 10 years.
A–22
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
Table A–26: LA module mechanical
Characteristic
Description
Slot width
Requires 2 mainframe slots
Weight
5 lbs 10 oz. (2.55 kg) for TLA 7L4 or TLA 7M4
8 lbs (3.63 kg) for TLA 7L4 or TLA 7M4 packaged for domestic shipping
Overall dimensions
Height
10.32 in (262 mm)
Width
2.39 in (61 mm)
Depth
14.7 in (373 mm)
Probe cables
P6417 length
Mainframe interlock
6 ft (1.8 m)
1.4 ECL keying is implemented
TLA 700 Series Logic Analyzer User Manual
A–23
Appendix A: Specifications
TLA 700 Series Digitizing Oscilloscope Module Characteristics
Table A–27: DSO module signal acquisition system
Characteristic
Description
n Accuracy, DC Gain
±1.5% for full scale ranges from 20 mV to 100 V
±2.0% for full scale ranges <19.9 mV
n
Accuracy, Internal Offset1
n Analog Bandwidth, DC–50 W Coupled
Bandwidth, Analog, Selections
Full Scale Range Setting
Offset Accuracy
10 mV – 1 V
±[(0.2% × | offset |) + 1.5 mV + (6% × full
scale range)]
1.01 V – 10 V
±[(0.25% × | offset |) + 15 mV + (6% × full
scale range)]
10.1 V – 100 V
±[(0.25% × | offset |) + 150 mV + (6% × full
scale range)]
Full Scale Range Setting
Bandwidth 2
10.1 V – 100 V
DC – 500 MHz (TLA7E1 and TLA7E2)
DC – 500 MHz (TLA7D1 and TLA7D2)
100 mV – 10 V
DC – 1 GHz (TLA7E1 and TLA7E2)
DC – 500 MHz (TLA7D1 and TLA7D2)
50 mV – 99.5 mV
DC – 750 MHz (TLA7E1 and TLA7E2)
DC – 500 MHz (TLA7D1 and TLA7D2)
20 mV – 49.8 mV
DC – 600 MHz (TLA7E1 and TLA7E2)
DC – 500 MHz (TLA7D1 and TLA7D2)
10 mV – 19.9 mV
DC – 500 MHz (TLA7E1 and TLA7E2)
DC – 500 MHz (TLA7D1 and TLA7D2)
20 MHz, 250 MHz, and FULL on each channel
Calculated Rise Time (Typical)3
Typical
ic l full-bandwidth
lli t rise times are
re sshown
o iin tthee
chart to the right
Full Scale Range Setting
TLA7D1 and
TLA7E1 and TLA7E2 TLA7D2
10.1 V – 100 V
900 ps
900 ps
100 mV – 10 V
450 ps
900 ps
50 mV – 99.5 mV
600 ps
900 ps
20 mV – 49.8 mV
750 ps
900 ps
10 mV – 19.9 mV
900 ps
900 ps
Crosstalk (Channel Isolation)
≥300:1 at 100 MHz and ≥100:1 at the rated bandwidth for the channel’s sensitivity
(Full Scale Range) setting, for any two channels having equal sensitivity settings
Digitized Bits, Number of
8 bits
A–24
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
Table A–27: DSO module signal acquisition system (Cont.)
Characteristic
Description
Effective Bits, Realtime Sampling (Typical)
Input Frequency
TLA7E1 and
TLA7E2 5 GS/s
(each Channel)
TLA7D1 and TLA7D2 2.5 GS/s
(each Channel)
10.2 MHz
6.2 bits
6.2 bits
98 MHz
6.1 bits
6.1 bits
245 MHz
6.0 bits
6.0 bits
490 MHz
5.7 bits
5.7 bits
990 MHz
5.2 bits
N/A
Frequency Limit, Upper, 20 MHz Bandwidth
Limited (Typical)
20 MHz
Frequency Limit, Upper, 250 MHz Bandwidth
Limited (Typical)
250 MHz
Input Channels, Number of
Product
Channels
TLA7E2
Four
TLA7D2
Four
TLA7E1
Two
TLA7D1
Two
Input Coupling
DC, AC, or GND4
Input Impedance, DC–1 MW Coupled
1 MW ±0.5% in parallel with 10 pF ±3 pF
Input Impedance Selections
1 MW or 50 W
Input Resistance, DC–50 W Coupled
50 W ±1%
Input VSWR, DC–50 W Coupled
≤1.3:1 from DC – 500 MHz, ≤1.5:1 from 500 MHz – 1 GHz
Input Voltage, Maximum, DC–1 MW, AC–1 MW,
or GND Coupled
300 VRMS but no greater than ±420 V peak, Installation category II, derated at
20 dB/decade above 1 MHz
Input Voltage, Maximum, DC–50 W or AC–50 W
Coupled
5 VRMS, with peaks ≤ ±25 V
Lower Frequency Limit, AC Coupled (Typical)
≤10 Hz when AC–1 MW Coupled; ≤200 kHz when AC–50 W Coupled5
n Random Noise
Bandwidth Selection
RMS Noise
Full
≤(350 mV + 0.5% of the full scale Setting)
250 MHz
≤(165 mV + 0.5% of the full scale Setting)
20 MHz
≤(75 mV + 0.5% of the full scale Setting)
TLA 700 Series Logic Analyzer User Manual
A–25
Appendix A: Specifications
Table A–27: DSO module signal acquisition system (Cont.)
Characteristic
Description
Range, Internal Offset
Full Scale Range Setting
Offset Range
10 mV – 1 V
±1 V
1.01 V – 10 V
±10 V
10.1 V – 100 V
±100 V
Range, Sensitivity (Full Scale Range),
All Channels
10 mV to 100 V6
Step Response Settling Errors (Typical)7
The maximum absolute difference between the
vvalue
l e att tthee end
e of
o a sspecified
eci ie time iinterval
terv l after
ter
t e mid-level
mi -level crossing
crossi of
o the
t e step,
ste and the
t e value
v l e
the
one second after the mid-level crossing of the
step, expressed as a percentage of the step
amplitude. See IEEE std. 1057, Section 4.8.1,
Settling Time Parameters.
± Step Response
Maximum Settling
Error (%) at
20 ns
100 ns 20 ms
10 mV – 1 V
≤2 V
0.5%
0.2%
0.1%
1.01 V – 10 V
≤20 V
1.0%
0.5%
0.2%
10.1 V – 100 V
≤200 V
1.0%
0.5%
0.2%
1
Net offset is the nominal voltage level at the digitizing oscilloscope input that corresponds to the center of the A/D
Converter dynamic range. Offset accuracy is the accuracy of this voltage level.
2
The limits given are for the ambient temperature range of 0_C to +30_C. Reduce the upper bandwidth frequencies by
5 MHz for each _C above +30_C. The bandwidth must be set to FULL.
3
Rise time (rounded to the nearest 50 ps) is calculated from the bandwidth when Full Bandwidth is selected. It is
defined by the following formula:
Rise Time (ns) = 450 BW (MHz)
GND input coupling disconnects the input connector from the attenuator and connects a ground reference to the
input of the attenuator.
4
A–26
Full Scale Range
Setting
5
The AC Coupled Lower Frequency Limits are reduced by a factor of 10 when 10X passive probes are used.
6
The sensitivity ranges from 10 mV to 100 V full scale in a 1–2–5 sequence of coarse settings. Between coarse
settings, you can adjust the sensitivity with a resolution equal to 1% of the more sensitive coarse setting. For
example, between the 500 mV and 1 V ranges, the sensitivity can be set with 5 mV resolution.
7
The Full Bandwidth settling errors are typically less than the percentages from the table.
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
Table A–28: DSO module timebase system
Characteristic
Description
Range, Extended Realtime Sampling Rate
5 S/s to 10 MS/s in a 1–2.5–5 sequence
Range, Realtime Sampling Rate
Products
Limits
TLA7E1 and
TLA7E2
25 MS/s to 5 GS/s on all channels simultaneously in a
1–2.5–5 sequence
TLA7D1 and
TLA7D2
25 MS/s to 2.5 GS/s on all channels simultaneously in a
1–2.5–5 sequence
Record Length
512, 1024, 2048, 4096, 8192, and 15000
n Long Term Sample Rate
±100 ppm over any ≥ 1 ms interval
Table A–29: DSO module trigger system
Characteristic
Description
n Accuracy (Time) for Pulse Glitch or
Pulse
P lse Wi
Width
t Triggering
ri eri
Time Range
Accuracy
2 ns to 500 ns
±(20% of Setting + 0.5 ns)
520 ns to 1 s
±(104.5 ns + 0.01% of Setting)
n Accuracy (DC) for Edge Trigger Level, DC
Coupled
±( ( 2% × | Setting) | ) + 0.03 of Full Scale Range + Offset Accuracy) for signals
having rise and fall times ≥20 ns
Range (Time) for Pulse Glitch and Pulse Width
Triggering
2 ns to 1 s
Range, Trigger Level
Source
Range
Any Channel
±100% of full scale range
Range, Trigger Point Position
Minimum: 0%
Maximum: 100%
Resolution, Trigger Level
0.2% of full scale for any Channel source
Resolution, Trigger Position
One Sample Interval at any Sample Rate
Sensitivities, Pulse-Type Runt Trigger (Typical)
10% of full scale, from DC to 500 MHz, for vertical settings >100 mV full scale and
≤10 V full scale at the BNC input
Sensitivities, Pulse-Type Trigger Width and
Glitch (Typical)
10% of full scale for vertical settings >100 mV full scale and ≤10 V full scale at the
BNC input
TLA 700 Series Logic Analyzer User Manual
A–27
Appendix A: Specifications
Table A–29: DSO module trigger system (Cont.)
Characteristic
Description
n Sensitivity, Edge-Type Trigger, DC Coupled
The minimum signal levels required for stable edge triggering of an acquisition when
the trigger source is DC-coupled
Sensitivity, Edge-Type Trigger, Not DC Coupled
(Typ c )
(Typical)
Time, Minimum Pulse or Rearm, and Minimum
r sitio Time,
ime for
or Pulse-Type
P lse- e Triggering
ri eri
Transition
(Typical)
Trigger Position Error, Edge Triggering (Typical)
1
A–28
Products
Trigger Source
Sensitivity
TLA7E1 and TLA7E2
Any Channel
3.5% of Full Scale Range
from DC to 50 MHz, increasing to 10% of Full
Scale Range at 1 GHz
TLA7D1 and TLA7D2
Any Channel
3.5% of Full Scale Range
from DC to 50 MHz, increasing to 10% of Full
Scale Range at 500 MHz
Trigger Coupling
Typical Signal Level for Stable Triggering
AC
Same as the DC-coupled limits for
frequencies above 60 Hz; attenuates
signals below 60 Hz
High Frequency Reject
One and one-half times the DC-coupled
limits from DC to 30 kHz; attenuates
signals above 30 kHz
Low Frequency Reject
One and one-half times the DC-coupled
limits for frequencies above 80 kHz;
attenuates signals below 80 kHz
Noise Reject
Three times the DC-coupled limits
For vertical settings >100 mV and ≤10 V at the BNC input
Pulse Class
Minimum Pulse Width
Minimum Rearm Width
Glitch
1 ns
2 ns + 5% of Glitch Width
Setting
Width
1 ns
2 ns + 5% of Width Upper
Limit Setting
Acquisition Mode
Trigger Position Error 1
Sample
±(1 Sample Interval + 1 ns)
The trigger position errors are typically less than the values given here. These values are for triggering signals
having a slew rate at the trigger point of ≥5% of full scale/ns.
TLA 700 Series Logic Analyzer User Manual
Appendix A: Specifications
Table A–30: DSO module front-panel connectors
Characteristic
Description
n Probe Compensator, Output Voltage
The Probe Compensator output voltage in
peak-to-peak Volts
0.5 V (base–top) ± 1% into a ≥ 50 W load
Table A–31: DSO module certifications and compliances
EC Declaration of Conformity –
Low Voltage
Compliance was demonstrated to the following specification as listed in the Official Journal of the
European Communities:
Low Voltage Directive 73/23/EEC
EN 61010-1:/A2 1995
Approvals
Safety requirements for electrical equipment for measurement,
control, and laboratory use
UL3111-1 – Standard for electrical measuring and test equipment
CAN/CSA C22.2 No. 1010.1 – Safety requirements for electrical equipment for measurement,
control and laboratory use
Safety Certification of Plug-in or
VXI Modules
For modules (plug-in or VXI) that are safety certified by Underwriters Laboratories, UL Listing
applies only when the module is installed in a UL Listed product.
For modules (plug-in or VXI) that have cUL or CSA approval, the approval applies only when the
module is installed in a cUL or CSA approved product.
Installation Category Descriptions
Conditions of Approval
Terminals on this product may have different installation category designations. The installation
categories are:
CAT III
Distribution-level mains (usually permanently connected). Equipment at this level is
typically in a fixed industrial location
CAT II
Local-level mains (wall sockets). Equipment at this level includes appliances, portable
tools, and similar products. Equipment is usually cord-connected
CAT I
Secondary (signal level) or battery operated circuits of electronic equipment
Safety Certifications/Compliances are made for the following conditions:
Temperature (operation): +5_C to +40_C
Altitude (maximum operation): 2000 meters
IEC Characteristics
Equipment type:
Test and Measuring
Installation Category II
Pollution Degree 2
Safety Class I
TLA 700 Series Logic Analyzer User Manual
A–29
Appendix A: Specifications
Table A–32: DSO module mechanical
Characteristic
Description
Slot width
Requires 2 mainframe slots
Weight
Products
Weight
TLA7D1 and TLA7E1
2.44 kg (5.38 lbs)
TLA7D2 and TLA7E2
2.55 kg (5.63 lbs)
Products
Weight
TLA7D1 and TLA7E1
6.35 kg (14 lbs)
TLA7D2 and TLA7E2
7.71 kg (17 lbs)
Weight, shipping
Overall Dimensions
Height: 262.05 mm (10.32 in)
Width: 60.66 mm (2.39 in)
Depth: 373.38 mm (14.70 in)
A–30
TLA 700 Series Logic Analyzer User Manual
Appendix B: TLA 700 Symbol File Format
The logic analyzer can extract range symbol information directly from object
files in the following formats:
H
OMF86
H
OMF286
H
OMF386
H
IEEE695
H
COFF
H
ELF/DWARF
H
ELF/STABS
For users whose code-generation tools do not generate these file formats, the
TLA 700 Symbol File (TSF) format (a text format) can be used. The TSF format
is used by the logic analyzer when it exports symbol files. The logic analyzer can
also read files in this format.
TLA 700 symbol files consist of alphanumeric symbol names and associated data
values. The files contain a header line and lines defining the symbol names and
values. Fields on a line are separated with white space (blank spaces or tabs).
The formats for the pattern symbol files and the various range symbol files
differ; if you need to use pattern symbols and range symbols, you use separate
files.
Both TLA 700 range and pattern symbol files have a .tsf file name extension
(filename.tsf).
The first few lines of a TSF symbol file are typically comment lines describing
when and how the file was generated.
# TLA700 Symbol File
# Created on Friday, May 29, 1998 at 09:52:03
# From file: "c:\quickstart\tla7qs.x"
All lines in a TSF file that begin with a pound sign (#) character are treated as
comments, unless the very next character is a plus sign (+). The plus sign
signifies a file reader directive. (An example of a file reader directive “#+” can
be seen in the header definition below.) The pound sign character can also
initiate a comment on the end of a symbol definition or other uncommented
lines. All text between the pound sign and the end of the line is treated as a
comment and ignored.
TLA 700 Series Logic Analyzer User Manual
B–1
Appendix B: TLA 700 Symbol File Format
TSF Headers
A TSF header identifies the file format version to potential file readers. It
specifies whether the file contains pattern or range symbols, the radix used to
specify symbol values, and an optional offset amount to be added to each symbol
value (for range symbol files).
The TSF Header is a file directive which means that the following information
begins with the special character combination of a pound sign character followed
immediately by a plus sign (#+). This is not a comment line. The special
character sequence is used to mark instructions to the file reader; these instructions are called “file directives.”
The following examples show sample file headers for a pattern symbol file and a
range symbol file. The first two lines are comments included for readability; they
are not required as part of the file header.
#
TSF Format
Type
Display Radix File Radix
# =============== ======= ============= ==========
#+ Version 2.0.131 PATTERN
HEX
HEX
#
TSF Format
Type Display Radix File Radix Offset
# =============== ===== ============= ========== ========
#+ Version 2.0.131 RANGE
HEX
HEX
00000000
The File Format Version number contains three fields. The first two fields are the
format major and minor version numbers. The logic analyzer will only read TSF
files where the major and minor version number of the file is less than or equal
to that of the TLA 700 application itself. The third field is the build number of
the application which generated the TSF file. The value of the third field is
ignored when the file is read.
The File Format Version number is followed by a key word, PATTERN or
RANGE, which signifies the type of symbols to be found in the file. TSF files
can contain either type of symbols, but no single file can contain both. The
header specifies the type for all symbols in the file.
The Display Radix field sets the default radix that will be used to display the
numeric symbol value. For range symbol files this field must be one of the key
words: HEX, DEC, OCT, or BIN. For pattern symbol files, only the key words:
HEX, OCT, or BIN are allowed.
The File Radix field specifies the radix used by the symbol values in this file.
Like the Display Radix field, the File Radix field must be one of the key words:
HEX, DEC, OCT, or BIN for range symbol files, or HEX, OCT, or BIN for
pattern symbol files.
B–2
TLA 700 Series Logic Analyzer User Manual
Appendix B: TLA 700 Symbol File Format
The Offset field specifies an offset value and is applicable only to range symbol
files. The offset value is specified in the radix indicated by the File Radix field.
This offset value will be added to the lower and upper bounds of each range
symbol that is read from the file. The offset is a 32-bit value, so it can have any
value between 0x00000000 and 0xFFFFFFFF. If the sum of the offset and a
range symbol bound value exceeds the 32-bit limit of 0xFFFFFFFF, the
overflow bit is discarded. Negative offsets are specified by using a twos
complement value for the offset.
TSF Pattern Symbols
Each pattern symbol in a TSF pattern file consists of two fields. The first field is
the symbol name, and the second is the symbol pattern. The symbol name is a
sequence of ASCII characters of up to 220 characters in length, although it is
impractical to display symbol values much longer than 32 characters. Symbol
names longer than 220 characters will be truncated during loading. The
characters in a symbol name can be any character with an ASCII value between
0x21 (the exclamation point character (!)) and 0x7E (the tilde character (~)). You
can use symbol names with embedded spaces by enclosing the Symbol Name in
double quotes.
# Symbol
# Name
# ======
NUL
SOH
STX
"ETX 0x03"
Symbol
Pattern
========
X0000000
X0000001
X0000010
X0000011
The symbol pattern consists of numerals in the radix specified by the File Radix
field in the header, and Xs signifying “don’t-care” values. The number of bits
represented by each character position in the pattern depends on the selected
radix. For a radix of HEX, each character represents 4 bits. For an OCT radix,
each character represents 3 bits; and for a BIN radix, each character represents
one bit.
Symbol order in a TSF pattern file is important. When selecting the symbol to
display for a particular value, the logic analyzer scans the list of pattern symbols
from top to bottom. It selects the first symbol for which all non-don’t-care bits of
the symbol match the corresponding bits of the target symbol.
TLA 700 Series Logic Analyzer User Manual
B–3
Appendix B: TLA 700 Symbol File Format
TSF Range Symbols
There are three different types of range symbols: function, variable and source.
Each of these three types define a range of 32 bit addresses associated with some
entity. Variable range symbols define the beginning and ending addresses where
the value of a variable is located in memory. Function range symbols define the
beginning and ending addresses where instructions that implement a function are
located in memory. Source range symbols are similar to function range symbols,
except that the address range for a source symbol describes the location of the
instructions that implement just one source statement. (Source symbols also
contain file name, line number, and an optional column range that define the
location of the source code associated with the symbol.)
Each of the three types of range symbols appear in a separate section of the file.
Each section begins with a file directive indicating the type of symbols that
follow. The sections may appear in any order, and can be broken up and
separated by other sections if necessary. The first section might be variables,
followed by functions, then followed by another variable section. Each section is
also optional, however some TLA 700 applications are unable to use the symbol
file if the appropriate type of symbols are not present. For example, the Source
window is only able to correlate with a Listing window if the symbol file
contains source symbols.
Range symbol names follow the same rules as pattern symbol names. The
symbol name is a sequence of ASCII characters of up to 220 characters in length,
although it is impractical to display symbol values much longer than 32
characters. Symbol names longer than 220 characters will be truncated during
loading. The characters in a symbol name can be any character with an ASCII
value between 0x21 (the exclamation point character (!)) and 0x7E (the tilde
character (~)). You can use symbol names with embedded spaces by enclosing
the Symbol Name in double quotes.
Range symbol address ranges can overlap, however, this sometimes produces
unexpected results. When overlaps occur, and the logic analyzer needs to convert
a numeric value to a symbol, it must to choose between the overlapping
symbols. When choosing between overlapping symbols, the logic analyzer
assigns a precedence order to the symbol types. Function symbols have the
highest precedence, followed by variable symbols, and then source symbols.
B–4
TLA 700 Series Logic Analyzer User Manual
Appendix B: TLA 700 Symbol File Format
TSF Function Symbols
The file directive “#+ Function” introduces the function symbol section of a TSF
Range file. The file directive tells the file reader that the following symbols
represent functions, as opposed to variables or source statements. If no symbol
type file directive is given, the function symbol type is assumed.
#+ Function
#
Symbol Name
# ==============================
displayBanner
buildMenus
displayLCDmenu
Low
========
006035ba
00603676
006036e6
High
========
00603675
006036e5
0060372f
Function symbols consist of three fields: the symbol name, the lower bound, and
the upper bound.
The lower and upper bound values are each 32-bit values, defined by numerals in
the radix specified by the File Radix field in the file header. These values define
the lower and upper limits of the range of addresses occupied by the instructions
which implement a function. Both values are inclusive, which means that the
specified range includes both of the bound values, as well as all of the addresses
between them.
TSF Variable Symbols
The file directive “#+ Variable” introduces the variable symbol section of a TSF
Range file. The file directive tells the file reader that the following symbols
represent variables, as opposed to functions or source statements. If no symbol
type file directive is given, the function symbol type is assumed.
#+ Variable
#
Symbol Name
# ==============================
menu
userMenu1
binBits
Low
========
00000100
000004c0
000004d4
High
========
00000102
000004c2
000004d6
Variable symbols consist of three fields: the symbol name, the lower bound, and
the upper bound. Variable symbols are just like function symbols except that
they define the address range occupied by a variable, instead of function. The
lower and upper bound values of a variable symbol are inclusive, meaning that
they are themselves a part of the range. For variables occupying only a single
byte in memory, the lower and upper bound values are equal.
TLA 700 Series Logic Analyzer User Manual
B–5
Appendix B: TLA 700 Symbol File Format
TSF Source Symbols
The file directive “#+ Source” introduces the source symbol section of a TSF
range file. The file directive tells the file reader that the following symbols
represent source statements, as opposed to functions or variables. The source file
directive must be followed by a file name which specifies the name of the source
file containing the following source statements. Each new set of symbols for a
unique source file must be introduced with an additional source file directive to
specify the file name for those symbols. If no symbol type file directive is given,
the function symbol type is assumed.
#+ Source stoplite
# Line Low
High
# ==== ======== ========
27 006043ec 006043ef
35 006043f0 006043f5
47 006043f6 006043ff
48 00604400 00604409
49 0060440a 00604413
50 00604414 0060441d
51 0060441e 00604427
52 00604428 00604431
56 00604432 00604437
59 00604438 00604439
60 0060443a 00604445
61 00604446 0060444d
59 0060444e 0060444f
59 00604450 00604455
71 00604456 00604457
74 00604458 0060445f
77 00604460 00604467
80 00604468 0060446f
83 00604470 0060447b
87 0060447c 00604483
71 00604484 0060448d
84 0060448e 00604490
Beg
===
0
0
0
0
0
0
0
0
0
0
0
0
35
19
0
0
0
0
0
0
0
0
End
===
25
23
30
30
30
30
30
30
17
18
37
33
39
34
37
35
36
36
43
34
37
29
Symbol Name
===========
# stoplite_27_25
# stoplite_35_23
# stoplite_47_30
# stoplite_48_30
# stoplite_49_30
# stoplite_50_30
# stoplite_51_30
# stoplite_52_30
# stoplite_56_17
# stoplite_59_18
# stoplite_60_37
# stoplite_61_33
# stoplite_59_35
# stoplite_59_19
# stoplite_71_37
# stoplite_74_35
# stoplite_77_36
# stoplite_80_36
# stoplite_83_43
# stoplite_87_34
# stoplite_71_37
# stoplite_84_29
The source symbols section consists of five fields for each source statement: line
number, lower address bound, upper address bound, beginning column value,
and ending column value.
Source symbols do not have a name in the same sense as function or variable
symbols, because there is no name associated with each of the executable
statements in a source file. Instead, a source symbol has a file name, specified in
the source directive, and a line number. The line number specifies the line of the
source file that contains the source statement. Line numbers are always in
decimal regardless of the file radix in the header.
B–6
TLA 700 Series Logic Analyzer User Manual
Appendix B: TLA 700 Symbol File Format
The lower and upper bound values for a source symbol are similar to those of
function and variable symbols. For source symbols, these bounds represent the
range of addresses occupied by the instructions that implement a single source
statement. The bound values are defined in the file radix specified in the header
and can range in value from 0x00000000 to 0xFFFFFFFF. The lower and upper
bound addresses are inclusive, just like other symbols. A source symbol for an
instruction occupying a single memory location has matching lower and upper
bound values.
The beginning and ending column fields of a source statement are optional.
When present, and non-zero, they define the beginning and ending column
position for the source statement. In other words, the beginning and ending
column values define the location of the statement in the line. This is especially
useful when there are multiple statements on a single line, because it makes it
possible to define a separate symbol for each statement. When the column
information is not present, or is set to zero, the symbol is assumed to correspond
to the entire line.
Only a few compilers generate column information, but when the information is
present, in the symbol file, the logic analyzer uses the column information to
provide highly accurate source code correlation. The example source symbols on
the previous page show typical column values. In most cases, only one of the
column values is non-zero. This is because those lines contain only one
statement, and the compiler specified only the column at which the statement
ended. Some compilers specify only the beginning column position for such
lines, in which case the beginning value would be non-zero and the ending value
zero.
Note that there are three symbols corresponding to line 59 of the file. Line 59 of
the original source file contains the following statement:
This one line contains three separate statements. The first statement is the
initialization , the second statement is the test , and
the third statement is the increment . Although all three statements appear
on the same line, each generates a separate set of instructions, and the symbols in
the example define unique address ranges for each. This enables the Source
window to accurately indicate which of the three statements on the line is
associated with any given address.
Each of the source symbols in the example includes a comment at the end of the
line showing a symbol name. Since this is a comment, it is ignored by the
symbol file reader, and is optional. When symbol files are exported by the logic
analyzer, they contain comments that show the derived symbol name created by
the logic analyzer itself. The name is a concatenation of the symbol file name,
line number, and column number (if present). This is the symbol value that the
logic analyzer will display for addresses that fall within the lower and upper
bounds of a source symbol.
TLA 700 Series Logic Analyzer User Manual
B–7
Appendix B: TLA 700 Symbol File Format
B–8
TLA 700 Series Logic Analyzer User Manual
Appendix C: User Service
This appendix describes general care and service procedures for the logic
analyzer. Additional information, such as user troubleshooting procedures and
replacing LA module probe podlets, is located in the TLA 700 Series Logic
Analyzer Installation Manual.
Mainframe and module service troubleshooting procedures are located in the
service manuals (see the Preface for a list of manuals).
General Care
Protect the instrument from adverse weather conditions. The instrument is not
waterproof.
Do not store or leave the portable mainframe where the LCD display will be
exposed to direct sunlight for long periods of time.
CAUTION. To avoid damage to the instrument, do not expose it to sprays, liquids,
or solvents.
Module Self Calibration
Use the Self Calibration property page to run self calibration procedures for
installed modules and merged modules. For all modules, you should run these
procedures after repair. At a minimum, you should run these procedures once a
year. For the DSO module you should also run these procedures if the ambient
operating temperature has changed more than 5_C since last calibration or once a
week if vertical settings of 50 mV full scale or less are used.
Perform self calibration after a 30 minute warm up.
H
To run the self-calibration procedure, go to the System menu and select
Calibration and Diagnostics. Click Self Calibration.
NOTE. For merged modules, you should run the self-calibration procedure on the
modules as a merged pair.
TLA 700 Series Logic Analyzer User Manual
C–1
Appendix C: User Service
Preventive Maintenance
Once a year the electrical performance should be checked and the instrument
accuracy certified (calibrated). This service should be performed by a qualified
service technician using the procedures outlined in the TLA 700 Series Performance Verification and Adjustment Technical Reference Manual.
Preventive maintenance mainly consists of periodic cleaning. Periodic cleaning
reduces instrument breakdown and increases reliability. You should clean the
instrument as needed, based on the operating environment. Dirty conditions may
require more frequent cleaning than computer room conditions.
Flat Panel Display
Cleaning
The TLA 704 Portable Mainframe display is a soft plastic display and must be
treated with care during cleaning.
CAUTION. Improper cleaning agents or methods can damage the flat panel
display.
Do not use abrasive cleaners or commercial glass cleaners to clean the display
surface.
Do not spray liquids directly on the display surface.
Do not scrub the display with excessive force.
Clean the flat panel display surface by gently rubbing the display with a
clean-room wipe (such as Wypall Medium Duty Wipes, #05701, available from
Kimberly-Clark Corporation).
If the display is very dirty, moisten the wipe with distilled water or a 75%
isopropyl alcohol solution and gently rub the display surface. Avoid using excess
force or you may damage the plastic display surface.
Exterior Mainframe
C–2
Clean the exterior surfaces of the mainframe with a dry, lint-free cloth or a
soft-bristle brush. If dirt remains, use a cloth or swab dampened with a 75%
isopropyl alcohol solution. A swab is useful for cleaning in narrow spaces
around the controls and connectors. Do not use abrasive compounds on any part
of the mainframe.
TLA 700 Series Logic Analyzer User Manual
Appendix C: User Service
CAUTION. Avoid getting moisture inside the mainframe during external cleaning;
and use only enough solution to dampen the cloth or swab.
Do not wash the front-panel On/Standby switch. Cover the switch while washing
the mainframe.
Use only deionized water when cleaning. Use a 75% isopropyl alcohol solution
as a cleanser and rinse with deionized water.
Do not use chemical cleaning agents; they may damage the instrument. Avoid
chemicals that contain benzene, toluene, xylene, acetone, or similar solvents.
Floppy Disk Drive
The floppy disk drive requires routine maintenance to operate at maximum
efficiency. The disks can be damaged if dirt and dust accumulate on the
recording surfaces. To prevent damage, the disks should be properly stored in
their protective containers where they will not be exposed to dust or dirt. In
addition, the head should be cleaned periodically.
You will need a 3.5-inch floppy disk head-cleaning kit for routine maintenance.
Perform the routine maintenance as follows:
H
Clean the face of the floppy disk drive monthly with a dampened cloth.
CAUTION. Do not allow moisture to enter the disk drive. When power is applied,
the internal components may be damaged.
H
External Monitor,
Keyboard, and Mouse
Clean the head monthly. Follow the instructions provided with the headcleaning kit.
Clean the exterior surfaces of the monitor, keyboard, and mouse with a dry,
lint-free cloth or a soft-bristle brush. A swab is useful for cleaning in narrow
spaces around the controls and connectors. Do not use abrasive compounds on
any part of the instrument.
CAUTION. Avoid getting moisture inside the terminal during external cleaning;
and use only enough solution to dampen the cloth or swab.
Use only deionized water when cleaning. Use a 75% isopropyl alcohol solution
as a cleanser and rinse with deionized water.
Do not use chemical cleaning agents; they may damage the instrument. Avoid
chemicals that contain benzene, toluene, xylene, acetone, or similar solvents.
TLA 700 Series Logic Analyzer User Manual
C–3
Appendix C: User Service
In Case of Problems
The logic analyzer runs power-on diagnostics every time you power on the
instrument. You can view the results of the diagnostics by selecting Calibration
and Diagnostics from the System menu. You can run more detailed diagnostics
by selecting Extended diagnostics. Here you can run all tests, loop on one or
more tests, or loop on a test until a failure occurs.
Refer to the chapter In Case of Problems in the TLA 700 Series Logic Analyzer
Installation Manual for information about software and hardware problems that
you might encounter.
Repacking for Shipment
If a mainframe or module is to be shipped to a Tektronix field office for repair,
attach a tag to the mainframe or module showing the owner’s name and address,
the serial number, and a description of the problem(s) encountered and/or service
required. If you are returning a module, always return both the module and the
probes so that the entire unit can be tested.
When packing an instrument for shipment, use the original packaging. If it is
unavailable or not fit for use, contact your Tektronix representative to obtain new
packaging.
C–4
TLA 700 Series Logic Analyzer User Manual
Appendix D: Probe and Connector Information
P6417 Probe Information
.200 Min
.700
.100
.400
Max
.150
.100
.100
.150 Min
.700
.100
16 Channels plus one
clock – pin spacing
.900 Max
8 Channel probe footprint
Section names
Orange probe
Brown probe
Gray probe
White probe
Yellow probe
Blue probe
Violet probe
Green probe
A0
A2
C0
C2
D0
D2
E0
E2
0
A1
A3
C1
C3
D1
D3
E1
E3
7
GND
0
Clock channel
CK1
CK0
Q1
CK3
CK2
Q0
Q2
Q3
.050
.150
.400
Max
.100
7 CLK
GND
GND
.100 Max
16 Channels plus one
clock – grouping footprint
Single podlet footprint
Figure D–1: P6417 probe footprints
1.75 in
(44 mm)
Figure D–2: P6417 probe podlet clearance
TLA 700 Series Logic Analyzer User Manual
D–1
Appendix D: Probe and Connector Information
P6434 Probe Information
The P6434 Mass Termination probes are available as an option to the TLA 700
Series Logic Analyzer. For information on using this probe refer to the P6434
Mass Termination Probe Instructions (Tektronix part number 070-9793-01 or
higher).
You can also access a PDF file for design guideline instructions at the following
web site:
Use the following instructions to access the PDF files at the above web site:
1. Click Application Support Files.
2. Scroll to the TLA7xx Files Area.
3. Click p6434.pdf to download the design-in guideline titled Mass Termination Probe Document.
D–2
TLA 700 Series Logic Analyzer User Manual
Appendix D: Probe and Connector Information
Benchtop Mainframe Remote On/Standby Switch
The 25-pin Sub-D connector at the rear of the benchtop mainframe provides
remote on and off capability. Figure D–3 shows the connector.
Connect only a momentary switch or an open collector device to pin 5 of the
connector. By momentarily grounding this line, the mainframe will toggle from
on to standby (or vice versa). The state changes on the falling edge of the signal.
Hold the signal low for at least 500 ms before releasing.
Pin 1
Pin 25
Figure D–3: Connector used for remote On/Standby switch
TLA 700 Series Logic Analyzer User Manual
D–3
Appendix D: Probe and Connector Information
D–4
TLA 700 Series Logic Analyzer User Manual
Glossary
Glossary
AC coupling
A DSO mode that blocks the DC component of a signal but passes the
dynamic (AC) component of the signal. Useful for observing an AC signal
that is normally riding on a DC signal.
Acquisition
The process of sampling signals from input channels, processing the results,
and displaying the data.
Active module
The module highlighted by the pointer in the System window.
Aliasing
The condition that occurs when data is sampled at a rate slower than the rate
at which data changes. When this happens, misleading data is displayed
because the instrument misses the changes in data that occurred between
sample points. Data pulses that fall between samples meet the technical
definition of a glitch and are stored and displayed as glitches. See also
asynchronous acquisition and glitch.
For DSO data, the displayed waveform may appear to be untriggered and
much lower in frequency. For complex waveforms, distortion occurs due to
the impact of aliasing on the high-order harmonics.
All samples
A Histogram window term. The total number of data samples analyzed.
Arm
To specify when the module should begin looking for a trigger.
Assert
To cause a signal or line to change from its logic false state to its logic true
state.
Asynchronous acquisition
An acquisition that is made using a clock signal generated internally by the
logic analyzer. This clock is unrelated to the clock in the system under test,
and you can set it to a different rate. You should use an asynchronous clock
rate that is five to ten times faster than your data rate to avoid aliasing. See
also Aliasing.
TLA 700 Series Logic Analyzer User Manual
Glossary–1
Glossary
Attenuation
The degree the amplitude of a signal is reduced when it passes through an
attenuating device such as a DSO probe or attenuator (the ratio of the input
measure to the output measure). For example, a 10X probe attenuates, or
reduces, the input voltage of a signal by a factor of 10.
Clause
A trigger program term. The combination of one or more events (If
statements) or actions (Then statements). When the Event is satisfied, the
action is performed. See also State.
Clock cycle
A clock sequence that includes both high- and low-going transitions.
Clock equation
The Boolean combination of events needed to generate a storage clock. You
can define a variety of clock inputs and link them using Boolean operators.
Data will be sampled and stored in memory only when this clock equation is
true.
Clock qualification
The process of filtering out irrelevant data by combining an acquisition clock
with one or more bus signals.
Clock qualifier
An external signal that acts as a gate for the acquisition clock. When the
external signal is false, the acquisition clock is not allowed to load acquired
data into the acquisition memory.
COFF file formats
The COFF (Common Object File Format) format contains a number of
variations and extensions, such as ECOFF and XCOFF. This flexibility
enables it to be used with a wide variety of different microprocessors. Some
code-generation tool vendors also extend this format in non–standard ways
that may make their files unreadable by the TLA 700 logic analyzers.
Counter
A trigger program device that records occurrences of an event.
Cursors
Paired markers that you can use to make measurements between two data
locations.
Custom clocking
Custom clocking is used only with microprocessor support packages.
Custom clocking can enable and disable a variety of microprocessor-specific
clock cycle types (such as DMA cycles).
Glossary–2
TLA 700 Series Logic Analyzer User Manual
Glossary
Data differences
Highlighted data in a Listing or Waveform window that indicate that there
are differences between the acquired data and saved data during a compare
operation.
Data equalities
Highlighted data in a Listing or Waveform window that indicate that there
are no differences between the acquired data and saved data during a
compare operation.
Data sample
The data logged in during one occurrence (or one cycle) of the acquisition
clock. A data sample contains one bit for every channel.
Data window
A window used to display acquired data. There are two types of data
windows, Listing windows and Waveform windows.
DC coupling
A DSO mode that passes both AC and DC signal components to the DSO
circuit. Available for both the trigger system and the vertical system.
Delta measurement
The difference between two points in memory. For example, the voltage
difference between the two cursors in a selected waveform.
Demultiplex
To identify and separate multiplexed signals (for instance, some signals from
a microprocessor). To separate different signals sharing the same line and
organize those signals into useful information.
Digital real-time signal acquisition
A digitizing technique that samples the input signal with a sample frequency
of four to five times the DSO bandwidth. Combined with sin(x)/x interpolation, all frequency components of the input up to the bandwidth are
accurately displayed.
Digitizing
The process of converting a continuous analog signal such as a waveform to
a set of discrete numbers representing the amplitude of the signal at specific
points in time.
Don’t care
A symbol (X) used in place of a numeric character to indicate that the value
of a channel or character is to be ignored.
Edge
A signal transition from low to high, or high to low.
TLA 700 Series Logic Analyzer User Manual
Glossary–3
Glossary
Edge trigger
Triggering that occurs when the module detects the source passing through a
specified voltage level in a specified direction (the trigger slope).
Event condition
Event conditions are a logical combination of trigger events within a single
clause. If you set up a logical AND statement, all event conditions in the
clause must be fulilled before the clause can execute the action. If you set up
a logical OR statement, any one of the event conditions can be fulfilled
before the clause can execute the action.
External clock
A clock external to the logic analyzer and usually synchronous with the
system under test.
Internal signal
An internal communication line that can be set as a marker. An internal
signal can be used as either an event or an action in a trigger program. When
used as an event, the internal signal is tested for true/false value like any
other event; when used as an action, the signal can simply be set or cleared
as the result of a condition being satisfied.
Glitch
An unintentional signal that makes a transition through the threshold voltage
two or more times between successive sample clock cycles. Noise spikes and
pulse ringing are examples of glitches.
Ground (GND) coupling
A DSO coupling option that disconnects the input signal from the vertical
system.
Histogram window
A data window used to observe the performance of software routines.
IEEE695 file format
This object file format refers to the IEEE695 specification. This format is
used primarily by compilers for a wide variety of Motorola microprocessors
and compatible microprocessors from other vendors. This format provides
for the inclusion of column information in source symbols, but not all
compilers use this capability.
Internal clock
A clock mode in which the sampling of input logic signals occurs asynchronously to the activity of the system under test.
Interpolation
Display method used to connect the sample points acquired and display them
as a continuous waveform. The logic analyzer uses sin(x)/x interpolation to
display DSO signals.
Glossary–4
TLA 700 Series Logic Analyzer User Manual
Glossary
Linear generation
A Histogram window term. The histogram ranges are evenly distributed
from the highest range boundary to the lowest range boundary.
Listing window
A data window used to observe the data flow in the system under test. The
acquired data is displayed in a listing (tabular text) format.
Log generation
A Histogram window term. The histogram ranges are distributed over a
logarithmic scale.
MagniVu data
High-speed data stored in a special memory.
Matched samples
A Histogram window term. The total number of data samples analyzed that
matched a defined range. These samples exclude any samples outside of the
defined ranges.
Merge modules
To physically or logically join two LA modules together to form a single
module with greater channel width.
Microprocessor support
Optional microprocessor support software that allows the logic analyzer to
disassemble data acquired from microprocessors.
Mnemonic disassembly
A display format for data acquired from a microprocessor or a data bus. A
logic analyzer decodes bus activity and displays it in formats such as: cycle
types, instruction names, and interrupt levels. Advanced forms of mnemonic
disassembly can detect queue flushes, and provide a display that resembles
the original assembly language source code listing.
Module
The unit that plugs into a mainframe, providing instrument capabilities such
as logic analysis.
Module trigger (trigger)
A trigger specific to a single module. When a module trigger occurs, the
module continues to acquire data until the specified amount of posttrigger
data is acquired, and then stops.
OMF86 file format
A file format that holds symbolic information and executable images for an
8086 or equivalent microprocessor. It is also used for code intended to run on
80286, 80386, or higher-level microprocessors in real or 8086-compatible
mode.
TLA 700 Series Logic Analyzer User Manual
Glossary–5
Glossary
OMF286/386 file formats
These file formats hold symbolic informaton and executable images for
80286 80386, or equivalent microprocessors. They are also used for
executable images intended to run on the 8086 or other microprocessors in
the 80x86 families.
Podlet
A circuit contained in a flex lead and attached to a probe that provides
square-pin connections to the circuit under test for one data acquisition
channel and a ground pin.
Pretrigger
The specified portion of the data record that contains data acquired before
the trigger event.
Probe adapter
A microprocessor-specific lead set that connects the LA module probe to a
system under test.
Qualification gap
Qualification gaps indicate that data samples were not stored due to storage
qualification or Don’t Store trigger actions. In a Listing window, qualification gaps are indicated by a horizontal gray line. In a Waveform window,
qualification gaps are indicated by a blank vertical gap.
Range recognizer
A trigger term. Use range recognizers to trigger the logic analyzer on ranges
of data.
Record length
The specified number of samples in an acquisition.
Sample clock
The clock signal that determines the points in time when the module
samples data. A sample clock can be set up to occur at regular intervals
specified by an internal clock (asynchronous acquisition), or to occur when a
Boolean expression combining an external clock and qualifier signals is
“true” (synchronous acquisition).
Sample rate
The frequency at which data is logged into the logic analyzer.
Sampling
The process of capturing an input signal, such as a voltage, at a discrete
point in time and holding it constant so that it can be quantized.
Skew
The relative time difference between input channels, specified in terms of
one edge relative to another. Also, the misrepresentation of data caused by
parallel channels with different propagation delays.
Glossary–6
TLA 700 Series Logic Analyzer User Manual
Glossary
Source Window
A data window where you can view the execution of source code.
Standby (STBY)
The off-like state when the instrument in not in use. Some circuits are active
even while the instrument is in the standby state.
State
A trigger program term. A step in a trigger program, made up of one or more
clauses. See also clause.
Storage qualification
The process of filtering out data that has been acquired but which you do not
want to store in acquisition memory. This allows you to avoid filling up your
module’s acquisition memory with irrelevant data samples.
Symbolic range generation
A Histogram window term. The histogram ranges are defined in a range
symbol file. The highest and lowest ranges depend on the maximum and
minimum boundaries for the ranges defined in the symbol file.
Symbolic radix
A format that allows you to substitute mnemonics (names) for radix numbers
in the Trigger and data windows.
Synchronous acquisition
An acquisition that is made using a clock signal generated external to the
logic analyzer. This clock is usually the clock in the system under test. The
external clock is usually synchronous with the system under test and may or
may not be periodic.
System trigger (trigger all)
An overriding command to all modules that causes them to stop looking for
a trigger, and to acquire their posttrigger data, regardless of whether they
have been armed or have fulfilled their own trigger conditions. The system
trigger also functions as the primary reference point for the entire data
acquisition. In data windows, timing and location information is relative to
the system trigger.
Time correlation
The tracking of independent events captured by different modules and
indicating how they relate to each other in time. Specifically, the chronological interleaving of data from different modules into a single display. Shows
real-time interactions between independently clocked circuits.
Time stamp
A separate clock value stored with each acquisition cycle.
Timer
A trigger program device that records elapsed time.
TLA 700 Series Logic Analyzer User Manual
Glossary–7
Glossary
Threshold voltage
The voltage to which the input signals are compared.
Trigger
An event or condition that leads to the end of an acquisition cycle. When
started, the instrument continuously acquires data from a system under test
until the trigger occurs. After triggering, the instrument continues to acquire
data until the post-fill requirement is met.
Trigger library
A collection of predefined trigger programs for the LA module. You can load
an individual program into the Trigger window and modify it for your
requirements.
Trigger position
Where the trigger resides in acquisition memory. Electing to place the trigger
in the center of memory means that half of the acquisition consists of data
that occurred after the trigger.
Trigger program
A series of conditions, similar to software code, that defines the data you
want to capture and view. The trigger program also specifies actions for data
events. The trigger program filters acquired data to find a specific data event,
or series of data events. The trigger program can accept information from
other modules, or send signals external to the logic analyzer.
Unassert
To cause a signal or line to change from its logic true state to its logic false
state.
Waveform window
A data window used to observe timing relationships in the system under test.
The acquired data is displayed as a series of waveforms.
Word recognizer
A trigger term. Word recognizers are specific patterns of data or words. Use
word recognizers to trigger the logic analyzer on specific data combinations.
Glossary–8
TLA 700 Series Logic Analyzer User Manual
Index
Index
Symbols
.tbf format
DSO module data, 3–84
LA module data, 3–84
A
AC coupling, Glossary–1
Accelerator keys
general purpose data window, 3–51
Histogram window, 3–108
Listing window, 3–86
menu keys, 3–40
Source window, 3–100
Waveform window, 3–70
Acquisition, 2–1, 3–41, Glossary–1
asynchronous, 2–3, Glossary–1
DSO module, 2–1
LA module, 2–1
MagniVu data, 3–62, 3–79
mode, 3–8
module relationship, 2–7
synchronous, 2–2, Glossary–7
Active Cursor readout, 3–94
Active module, Glossary–1
Activity Indicators dialog box, 3–11
Add Column dialog box, 3–80
Add Waveform dialog box, 3–66
Advanced clocking, 3–8
Aliasing, 2–14, Glossary–1
bandwidth filters, 3–27
Aligning data, 3–49
All samples, Glossary–1
Arm, Glossary–1
arming modules, 3–31
indicator, 3–1
Assert, Glossary–1
Asynchronous acquisition, 2–3, Glossary–1
See also Internal clock
Attenuation, 2–4, Glossary–2
Autoset, 3–26
B
Bandwidth, DSO module setup, 3–27
Basic concepts, 2–1
Binary data, exporting, 3–83
Block diagram
TLA 700 Series Logic Analyzer User Manual
DSO module, 2–4, 2–5
LA module, 2–2
Blocks mode, 3–8
Busforms, 2–12, 3–54
C
Calibration
See also Self calibration
DSO probe, 3–25
Change detectors, 3–21
Channel activity, 3–11
Channel group, 3–9
adding/removing channels, 3–10
hardware order, 3–9
name, 3–10, 3–67, 3–81
polarity of channels, 3–10
probe thresholds, 3–12
Clause, 3–13, Glossary–2
Clause Definition dialog box, 3–18, 3–23, 3–31
Cleaning, C–2
LCD display, C–2
Clock, 2–2
advanced, 3–8
custom, 3–8
cycle, Glossary–2
DSO module, 3–28
equation, 3–7, Glossary–2
external, 2–2, 3–7, Glossary–4
internal, 2–3, 3–7, Glossary–4
multiple-phase, 3–8
problems, 3–44
qualification, Glossary–2
qualifier, Glossary–2
sample clock, 3–7, 3–28, Glossary–6
sample clock waveform, 3–56
sample rate vs. memory depth, 3–9
COFF file formats, Glossary–2
Color in data windows, 3–39, 3–68, 3–81, 3–97, 3–105
Column
adding, 3–80
changing width, 3–80
cut, copy, and paste, 3–80
cutting, 3–80
moving, 3–80
naming, 3–81
order, 3–10
Columns, sizing histograms, 3–104
Compare data, displaying, 3–63, 3–75
Index–1
Index
Comparing
listing data, 3–75
waveform data, 3–63
Comparing data, 2–18
Connectors
See also External signals
external, 1–19
Remote On/Standby switch, D–3
Contacting Tektronix, xv
Copying text, 3–80, 3–97
Correlation. See Time correlation
Counter, Glossary–2
Coupling, 3–27
Creating a Histogram window, 3–103
Creating a Source window, 3–88
Cursors, 3–56, 3–58, 3–71, 3–75, 3–89, 3–92,
Glossary–2
Custom clock, 3–8
Custom clocking, Glossary–2
Cutting
columns, 3–66, 3–80
columns, marks, 3–80
marks, 3–97
waveforms, marks, 3–67
D
Data, exporting, 3–82, 3–106
Data differences, Glossary–3
Data equalities, Glossary–3
Data marks, 3–56, 3–57, 3–71, 3–73, 3–89, 3–90
Data sample, Glossary–3
Data source, adding, 3–66, 3–80
Data window, 1–11, 3–47, Glossary–3
marks, cursors, and indicators, 3–71
splitting the data area, 3–81
Data, saving and loading. See Saved files
DC coupling, Glossary–3
Default settings, 3–39
Deleting. See Cutting
Delta measurement, 3–58, 3–75, Glossary–3
Demultiplex, Glossary–3
clock setting, 3–8
Diagnostics, C–4
Differences. See Data differences
Digital real-time signal acquisition, Glossary–3
Digitizing, 2–1, Glossary–3
Digitizing storage oscilloscope module. See DSO
module
Disabling modules, 3–2
Index–2
Disassembly format, changing, 3–81
Documentation list, xiii
Don’t care, Glossary–3
DSO, data, viewing in a Listing window, 2–8
DSO module
acquisition, 2–1
block diagram, 2–4
description, 1–2
export binary data, 3–84
horizontal controls, 3–28
self calibration, C–1
setup, 3–24
trigger controls, 3–28
vertical controls, 3–26
DSO probe calibration, 3–25
DSO setup, Autoset, 3–26
DSO Setup window, 3–24
DSO Trigger window, 1–10, 3–28
E
ECOFF. See COFF file formats
Edge, Glossary–3
Edge trigger, Glossary–4
Equalities. See Data equalities
Equation. See Clock, equation
Event condition, Glossary–4
Exporting
binary data, 3–83
histogram data, 3–106
listing data, 3–82
text data, 3–83
Exporting data, 3–82
Extended diagnostics, C–4
External
clock, 2–2, 3–7, Glossary–4
signal connectors, 1–19, 3–30
signals, 3–30, 3–32, 3–33
F
File name extension
saved files, 3–36
symbol files, B–1
Font in Histogram window, 3–104
Font in Listing window, 3–79
Font in Source window, 3–97
Front panel controls, 1–18
Function symbols, B–5
TLA 700 Series Logic Analyzer User Manual
Index
G
I
Gap, qualification, 3–81, Glossary–6
General maintenance, C–1
GlidePoint pad, 1–18
Glitch, 2–16, 3–8, Glossary–4
glitch mode, 3–8
Listing window, 3–81
Waveform window, 3–67
Go To dialog box, 3–59, 3–73, 3–90
Ground (GND) coupling, Glossary–4
Ground line indicator in DSO waveforms, 3–55
IEEE695 file format, Glossary–4
Installation, 1–2
Intermodule signals, 3–32
Internal clock, 2–3, 3–7, Glossary–4
Internal signal, 3–32, 3–45, Glossary–4
Interpolation, 2–15, Glossary–4
H
Help, online, 1–20
High-level language, 2–10, 3–87
High-speed timing. See MagniVu data
Histogram ranges
defining, 3–105
linear generation, 3–105
log generation, 3–105
symbols, 3–105
Histogram window, 1–13, 2–17, 3–101, Glossary–4
accelerator keys, 3–108
changing font size, 3–104
clearing counts, 3–104
columns, 3–104
creating, 3–103
customizing the display, 3–105
exporting data, 3–106
hot keys, 3–108
magnification, 3–105
measuring events, 3–103
printing, 3–107
shortcut keys, 3–108
sorting data, 3–104
splitting the data area, 3–105
stopping analysis, 3–104
viewing address activity, 3–102
Horizontal controls
DSO setup, 3–28
Waveform window, 3–67
Hot keys
general purpose data window, 3–51
Histogram window, 3–108
Listing window, 3–86
menu keys, 3–40
Source window, 3–100
Waveform window, 3–70
TLA 700 Series Logic Analyzer User Manual
J
Jumping to specific data locations, 3–59, 3–73, 3–90
K
Keypad, 1–18
L
LA module
acquisition, 2–1
block diagram, 2–2
description, 1–1
export binary data, 3–84
self calibration, C–1
setup, 3–3
trigger setup, 3–12
LA Setup window, 3–3
LA Trigger window, 1–9, 3–12
window structure, 3–14
Label. See Naming
Library, trigger, 3–16
creating your own trigger library, 3–38
Linear generation, 3–105, Glossary–5
Listing window, 1–11, 3–71, Glossary–5
See also Data window
accelerator keys, 3–86
changing font size, 3–79
columns, 3–80
cursors, 3–75
customizing the display, 3–81
disassembly format, 3–81
exporting binary data, 3–83
exporting data, 3–82
exporting text data, 3–83
hot keys, 3–86
jumping to specific data locations, 3–73
locking data windows together, 3–78
printing, 3–85
Index–3
Index
qualification gaps, 3–81
searching data, 3–77
shortcut keys, 3–86
viewing DSO data, 2–8
Listing-data concepts, 2–8
Load Symbol Options dialog box, 2–25
Load System Options dialog box, 3–37
Loading a trigger program, 3–18
Loading symbol files, 2–25
Locking windows, 3–61, 3–78
Log generation, 3–105, Glossary–5
Logic analyzer
basic concepts, 2–1
conceptual model, 2–6
description, 1–1
physical model, 2–5
specifications, A–1
Logic analyzer module. See LA module
M
Magnifying data in Histogram windows, 3–105
Magnitude mode, 2–12
Magnitude waveforms, 3–54
MagniVu data, 1–15, 2–7, 2–14, 2–15, 3–62, 3–79,
Glossary–5
Mainframe utilities, 1–3
Manuals list, xiii
Marks, 3–56, 3–57, 3–71, 3–73, 3–89, 3–90
cut, copy, and paste, 3–67, 3–80, 3–97
using the mark bar to jump to a new location, 3–59,
3–74, 3–91
Matched samples, Glossary–5
Measuring counter or timer events in Histogram
windows, 3–103
Measuring using cursors, 3–58, 3–75
Memory compare, 3–4
channel setups, 3–5
guidelines, 3–6
Memory depth, 2–14, 3–9, 3–28
See also Storage qualification
Merge modules, 3–34, Glossary–5
self calibration, 3–35, C–1
Microprocessor support, 3–4, 3–81, Glossary–5
channel grouping, 3–9
custom clock, 3–8
Mnemonic disassembly, Glossary–5
Module, 2–5, 2–6, Glossary–5
arming another module, 3–31
disabling, 3–2
identifying slot number, 3–2
intermodule interactions, 2–7
Index–4
joining two LA modules. See Merge modules
self calibration, 3–34, C–1
time correlation, 2–7
turning on/off, 3–2
Module trigger, Glossary–5
Multiple-phase clocking, 3–8
N
Naming
channel groups, 3–10
columns, 3–81
merged module probe names, 3–35
waveforms, 3–67
windows, 3–2
New Data Window wizard, 3–50
Next Mark and Previous Mark buttons, 3–94
Normal acquisition mode, 3–8
O
Offset
DSO module, 3–27
range symbols, 2–26, B–2
OMF286/386 file formats, Glossary–6
OMF86 file format, Glossary–5
On/Standby switch, 1–2
Online help, 1–20
Options, system, 3–39
P
Pattern symbols, 2–22, B–3
PC card connector, 1–19
Performance analysis, 2–17
Podlet, Glossary–6
Pointing device, 1–18
Polarity, LA channels, 3–10
Power-off procedure, 1–3
Power-on diagnostics, C–4
Power-on procedure, 1–2
Pretrigger, Glossary–6
Preventive maintenance, C–2
cleaning, C–2
disks, floppy disk drive, C–3
LCD display, C–2
Printing
Histogram window, 3–107
Listing window, 3–85
Source window, 3–99
Waveform window, 3–69
TLA 700 Series Logic Analyzer User Manual
Index
Probe adapter, Glossary–6
Probe calibration, DSO module, 3–25
Probe channel activity, 3–11
Probe Channels/Names table, 3–10
Probe podlet, Glossary–6
Probe thresholds
DSO vertical input, 3–26
LA channels, 3–12
Programmatic control, 1–17
Property sheets, 3–68, 3–81, 3–97, 3–105
Q
Qualification
clock, Glossary–2
gaps, 3–81, Glossary–6
storage, 2–3, 3–23, Glossary–7
Qualifier, clock, Glossary–2
R
Radix, 3–81
binary, glitch display, 3–81
changing, 3–81
symbolic, 2–21, 3–81, Glossary–7
Range readouts in DSO waveforms, 3–55
Range recognizer, Glossary–6
Range recognizers, 3–9, 3–21
Range symbols, 2–22, B–4
Record length, 3–9, 3–23, 3–28, Glossary–6
Remote On/Standby switch, D–3
Renaming. See Naming
Repacking for shipment, C–4
Repetitive acquisition, 3–42
Run/Stop button, 3–41
S
Sample
clock, 2–2, 2–14, 3–7, 3–56, Glossary–6
data, Glossary–3
period, DSO, 3–28
rate, 2–13, 2–14, Glossary–6
Sampling, Glossary–6
Sampling and digitizing a signal, 2–1
Sampling resolution, 2–13
Saved files, 1–15, 3–35, 3–36
backing up, 1–17
file name extension, 3–36
loading, 3–36
saved data, 3–38
TLA 700 Series Logic Analyzer User Manual
saved trigger, 3–38
setups and trigger programs, 3–37
system file, 3–37
module and system, 2–6
saving, 3–36
trigger programs, 3–24
Saving setups, triggers, or data. See Saved files
Scan Listing box, 3–92
Searching data, 3–60, 3–77, 3–95
Self calibration, 3–35, C–1
Service, user, preventive maintenance, C–2
Setup window, 1–8, 3–1
See also DSO Setup window; LA Setup window
Setups, saving and loading. See Saved files
Shipping, C–4
Shortcut keys
general purpose data window, 3–51
Histogram window, 3–108
Listing window, 3–86
menu keys, 3–40
Source window, 3–100
Waveform window, 3–70
Signals property page, 3–32
Sin(x)/x interpolation, 2–15
Single-run acquisition, 3–42
Skew, Glossary–6
Slot numbers, 3–2
Sorting data in Histogram windows, 3–104
Source Files property page, 3–97
Source symbols, B–6
Source window, 1–14, 3–87, Glossary–7
accelerator keys, 3–100
buttons, 3–93, 3–94
changing font size, 3–97
creating, 3–88
cursors, 3–92
customizing the display, 3–97
hot keys, 3–100
jumping to specific data locations, 3–90
marks, cursors, and indicators, 3–89
printing, 3–99
scan listing, 3–92
searching data, 3–95
shortcut keys, 3–100
Source Files property page, 3–97
Specifications, A–1
Splitting the data area, 3–68, 3–81, 3–105
Standby (STBY), Glossary–7
Starting and stopping acquisition, 3–41
State, 3–13, Glossary–7
State display. See Listing window
Status bar, hiding, 3–39
Index–5
Index
Status Monitor, 3–43
Step Forward and Step Backward buttons, 3–93
Storage qualification, 2–3, 3–23, Glossary–7
Storing data, 2–4, 2–5
Support package. See Microprocessor support
Symbol files
function symbols, B–5
loading, 2–25
pattern symbols, B–3
range, B–4
source symbols, B–6
variable symbols, B–5
viewing the status, 2–24
Symbolic radix, 2–21, Glossary–7
Symbolic range generation, Glossary–7
Symbols
function symbols, B–5
histogram ranges, 3–105
pattern symbols, B–3
range, B–4
source symbols, B–6
variable symbols, B–5
Symbols and symbol files, 2–21
file name extension, B–1
TLA 700 symbol file format (TSF), B–1
Symbols dialog box, 2–24
Synchronous acquisition, 2–2, Glossary–7
See also External clock
System defaults, 3–39
System options, 3–39
System trigger, 3–30, 3–49, Glossary–7
System window, 1–7, 3–1, 3–48
T
Technical support, xv
Tektronix binary format, 3–84
Tektronix, contacting, xv
Text data, exporting, 3–83
Threshold voltage, Glossary–8
Thresholds
DSO vertical input, 3–26
indicator in DSO waveform, 3–55
LA channels, 3–12
Time Alignment dialog box, 3–49
Time correlation, 2–7, 2–12, 3–49, Glossary–7
Time per div in Waveform window, 3–67
Time stamp, 2–8, Glossary–7
Index–6
Timer, Glossary–7
Timing display. See Waveform window
TLA 700 symbol file format, B–1
Toolbar
LA Trigger window, 3–18
Listing window, 3–79, 3–104
Source window, 3–96
Waveform window, 3–65
Touch pad, 1–18
TPI, 1–17, 2–20
Trigger, 2–3, Glossary–8
clause, 3–13, Glossary–2
DSO module, 2–4
DSO module setup, 3–28
indicator, 3–1, 3–15
LA trigger actions, 3–22
LA trigger events, 3–20
LA trigger resources, 3–20
LA Trigger window configuration, 3–12
library, 3–16
creating your own trigger library, 3–38
position, 3–24, 3–30, Glossary–8
problems, 3–44
program, 3–12, Glossary–8
debugging, 3–44
loading, 3–18
saving, 3–24
setting/clearing signals, 3–32
structure, 3–13
state, 3–13
storage qualification, 3–23
system, 3–30, 3–49, Glossary–7
external signal, 1–19, 3–30
Trigger library, Glossary–8
Trigger program, saving and loading. See Saved files
Trigger window. See DSO Trigger window; LA Trigger
window
Troubleshooting, C–4
logic analyzer does not trigger, 3–44
TSF pattern file header, B–2
TSF range file header, B–2
U
Unassert, Glossary–8
User service
general maintenance, C–1
preventive maintenance, C–2
TLA 700 Series Logic Analyzer User Manual
Index
V
Variable symbols, B–5
Vertical controls, DSO setup, 3–26
W
Waveform data concepts, 2–11
Waveform window, 1–12, 3–53, Glossary–8
See also Data window
accelerator keys, 3–70
cursors, 3–58
customizing the display, 3–68
hot keys, 3–70
jumping to specific data locations, 3–59
locking data windows together, 3–61
marks, cursors, and indicators, 3–56
printing, 3–69
searching data, 3–60
shortcut keys, 3–70
splitting the data area, 3–68
zoom, 3–67
Waveforms
adding, 3–66
busforms, 3–54
changing height, 3–67
changing horizontal scale, 3–67
changing width, 3–67
compression/expansion in display, 2–15
cut, copy, paste, 3–67
cutting, 3–66
DSO ground line indicator, 3–55
DSO range readouts, 3–55
DSO trigger threshold indicator, 3–55
DSO waveforms, 2–12, 3–55
LA waveforms, 2–12
magnitude, 3–54
TLA 700 Series Logic Analyzer User Manual
magnitude waveforms, 2–12
moving, 3–65
naming, 3–67
sample clock waveforms, 3–56
sin(x)/x interpolation, 2–15
single-channel LA waveforms, 3–54
types, 3–54
Weld modules. See Merge modules
Window
data window, 1–11, 3–47, Glossary–3
creating a new data window, 3–50
opening a saved data window, 3–49
DSO Setup window, 3–24
DSO Trigger window, 1–10, 3–28
Histogram window, 1–13, 3–101
LA Setup window, 3–3
LA Trigger window, 1–9, 3–12
Listing window, 1–11, 3–71, Glossary–5
locking data windows together, 3–61, 3–78
opening, 3–2, 3–48
overview, 1–6
renaming, 3–2
Setup window, 1–8
Source window, 1–14, 3–87
System window, 1–7, 3–1, 3–48
Waveform window, 1–12, 3–53, Glossary–8
Word recognizer, Glossary–8
Word recognizers, 3–21
X
XCOFF. See COFF file formats
Z
Zoom, 3–67
Index–7
Index
Index–8
TLA 700 Series Logic Analyzer User Manual

advertisement

Key Features

  • Capture and display signals from a variety of devices
  • Perform timing analysis
  • Perform state analysis
  • Perform data analysis
  • Support for various microprocessor and digital circuit families
  • High-level language (HLL) support
  • Waveform data concepts
  • Performance analysis concepts
  • Comparing acquired data against saved data
  • Repetitive acquisitions

Frequently Answers and Questions

What is the purpose of the TLA 700 Series Logic Analyzer?
The TLA 700 Series Logic Analyzer is a tool for debugging and analyzing digital systems. It can capture and display signals from a variety of devices, such as microprocessors, microcontrollers, and digital circuits. It can also be used for timing, state, and data analysis.
What is the difference between the LA module and the DSO module?
The LA module is designed to capture and display digital signals, while the DSO module captures and displays analog signals. They can be used together to provide a more complete picture of the system being analyzed.
How can I use the TLA 700 Series to debug a microprocessor system?
The TLA 700 Series Logic Analyzer supports various microprocessor families. Some functions that help with debugging include tracing the execution of code, identifying bus contention problems, and isolating data-related errors. You can use probes to connect to the signals of interest and capture data.
What are the key features of the TLA 700 Series Logic Analyzer?
Key features include the ability to capture and display signals from a variety of devices, perform timing analysis, perform state analysis, perform data analysis, support for various microprocessor and digital circuit families, high-level language (HLL) support, waveform data concepts, performance analysis concepts, comparing acquired data against saved data, and repetitive acquisitions.
What is the warranty for the TLA 700 Series Logic Analyzer?
The TLA 700 Series Logic Analyzer is warranted for one year from date of shipment.

Related manuals

Download PDF

advertisement