Denon S-102 DVD Home Entertainment System Service Manual
The Denon S-102 DVD Home Entertainment System is a complete home entertainment system that includes a DVD Surround Receiver, Sub Woofer, and Speaker System. This system provides high-quality audio and video for your movies, music, and games. With its advanced features, you can enjoy a truly immersive home entertainment experience.
PDF
Download
Document
Advertisement
Advertisement
Ver. 2 Please refer to the MODIFICATION NOTICE. SERVICE MANUAL MODEL JP S-102 E3 E2 EK E2A E1C E1K EUT 3 3 3 DVD HOME ENTERTAINMENT SYSTEM HOME ENTERTAINMENT SYSTEM (S-102) consists of DVD SURROUND RECEIVER (ADV-S102), SUB WOOFER (DSW-S102) and SPEAKER SYSTEM (SC-S102) 注 意 サービスをおこなう前に、このサービスマニュアルを 必ずお読みください。本機は、火災、感電、けがなど に対する安全性を確保するために、さまざまな配慮を おこなっており、また法的には「電気用品安全法」に もとづき、所定の許可を得て製造されております。 従ってサービスをおこなう際は、これらの安全性が維 持されるよう、このサービスマニュアルに記載されて いる注意事項を必ずお守りください。 本機の仕様は性能改良のため、予告なく変更すること があります。 ● 補修用性能部品の保有期間は、製造打切後 8 年です。 ● For purposes of improvement, specifications and design are subject to change without notice. ● ● Please use this service manual with referring to the operating instructions without fail. ● 修理の際は、必ず取扱説明書を参照の上、作業を行っ てください。 ● Some illustrations using in this service manual are slightly different from the actual set. ● 本文中に使用しているイラストは、説明の都合上現物 と多少異なる場合があります。 TOKYO, JAPAN Denon Brand Company, D&M Holdings lnc. X0341 V.02 DE/CDM 0710 S-102 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective. LASER RADIATION Do not stare into beam or view directly with optical instruments, class 3A laser product. CAUTION 注 意 Please heed the points listed below during servicing and inspection. サービス、点検時にはつぎのことにご注意願います。 ◎ Heed the cautions! ◎ Inspect for safety after servicing! ◎注意事項をお守りください! ◎サービス後は安全点検を! Spots requiring particular attention when servicing, such as the cabinet, parts, chassis, etc., have cautions indicated on labels or seals. Be sure to heed these cautions and the cautions indicated in the handling instructions. Check that all screws, parts and wires removed or disconnected for servicing have been put back in their original positions, inspect that no parts around the area that has been serviced have been negatively affected, conduct an insulation check on the external metal connectors and between the blades of the power plug, and otherwise check that safety is ensured. サービスのとき特に注意を必要とする個所についてはキャ ビネット、部品、シャーシなどにラベルや捺印で注意事項を 表示しています。これらの注意書きおよび取扱説明書などの 注意事項を必ずお守りください。 サービスのために取り外したねじ、部品、配線などが元どお りになっているか、またサービスした個所の周辺を劣化させ てしまったところがないかなどを点検し、外部金属端子部 と、電源プラグの刃の間の絶縁チェックをおこなうなど、安 全性が確保されていることを確認してください。 ◎ Caution concerning electric shock! (1) An AC voltage is impressed on this set, so touching internal metal parts when the set is energized could cause electric shock. Take care to avoid electric shock, by for example using an isolating transformer and gloves when servicing while the set is energized, unplugging the power cord when replacing parts, etc. (2)There are high voltage parts inside. Handle with extra care when the set is energized. ◎感電に注意! (1) このセットは、交流電圧が印加されていますので通電時 に内部金属部に触れると感電することがあります。従っ て通電サービス時には、絶縁トランスの使用や手袋の着 用、部品交換には、電源プラグを抜くなどして感電にご 注意ください。 (Insulation check procedure) Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and turn the power switch on. Using a 500V insulation resistance tester, check that the insulation resistance between the terminals of the power plug and the externally exposed metal parts (antenna terminal, headphones terminal, microphone terminal, input terminal, etc.) is 1MΩ or greater. If it is less, the set must be inspected and repaired. (2) 内部には高電圧の部分がありますので、通電時の取扱に は十分ご注意ください。 ◎ Caution concerning disassembly and assembly! ◎分解、組み立て作業時のご注意! Though great care is taken when manufacturing parts from sheet metal, there may in some rare cases be burrs on the edges of parts which could cause injury if fingers are moved across them. Use gloves to protect your hands. 板金部品の端面の『バリ』は、部品製造時に充分管理をして おりますが、板金端面は鋭利となっている箇所が有りますの で、部品端面に触れたまま指を動かすとまれに怪我をする場 合がありますので十分注意して作業して下さい。手の保護の ために手袋を着用してください。 ◎ Only use designated parts! The set's parts have specific safety properties (fire resistance, voltage resistance, etc.). For replacement parts, be sure to use parts which have the same properties. In particular, for the important safety parts that are marked ! on wiring diagrams and parts lists, be sure to use the designated parts. ◎ Be sure to mount parts and arrange the wires as they were originally! For safety reasons, some parts use tape, tubes or other insulating materials, and some parts are mounted away from the surface of printed circuit boards. Care is also taken with the positions of the wires inside and clamps are used to keep wires away from heating and high voltage parts, so be sure to set everything back as it was originally. CAUTION Concerning important safety parts Many of the electric and structural parts used in the set have special safety properties. In most cases these properties are difficult to distinguish by sight, and using replacement parts with higher ratings (rated power and withstand voltage) does not necessarily guarantee that safety performance will be preserved. Parts with safety properties are indicated as shown below on the wiring diagrams and parts lists is this service manual. Be sure to replace them with parts with the designated part number. ◎指定部品の使用! セットの部品は難燃性や耐電圧など安全上の特性を持った ものとなっています。従って交換部品は、使用されていたも のと同じ特性の部品を使用してください。特に配線図、部品 表に ! 印で指定されている安全上重要な部品は必ず指定の ものをご使用ください。 ◎部品の取付けや配線の引きまわしは、 元どおりに! (1) Schematic diagrams ... Indicated by the ! mark. (2) Parts lists ... Indicated by the ! mark. 安全上、テープやチューブなどの絶縁材料を使用したり、プ リント基板から浮かして取付けた部品があります。また内部 配線は引きまわしやクランパーによって発熱部品や高圧部 品に接近しないように配慮されていますので、これらは必ず 元どおりにしてください。 Using parts other than the designated parts could result in electric shock, fires or other dangerous situations. 2 (絶縁チェックの方法) 電源コンセントから電源プラグを抜き、アンテナやプラグな どを外し、電源スイッチを入れます。500V 絶縁抵抗計を用 いて、電源プラグのそれぞれの端子と外部露出金属部[アン テナ端子、ヘッドホン端子マイク端子、入力端子など]との 間で、絶縁抵抗値が1 MΩ 以上であること、この値以下の ときはセットの点検修理が必要です。 注 意 安全上重要な部品について 本機に使用している多くの電気部品、および機構部品は安全 上、特別な特性を持っています。この特性はほとんどの場合、 外観では判別つきにくく、またもとの部品より高い定格(定 格電力、耐圧)を持ったものを使用しても安全性が維持され るとは、限りません。安全上の特性を持った部品は、この サービスマニュアルの配線図、部品表につぎのように表示し ていますので必ず指定されている部品番号のものを使用願 います。 (1) 配線図… ! マークで表示しています。 (2) 部品表… ! マークで表示しています。 指定された部品と異なるものを使用した場合に は、感電、火災などの危険を生じる恐れがあり ます。 S-102 DIMENSION ADV-S102 43 294 43 149 1.5 4558 294 152 0.5 max. 122.5 10 83 135 45 380 3 S-102 41 167.5 336.5 DSW-S102 65 141 287 140 212 56 0.5 213 4 S-102 257.5 76.3 SC-S102 103.5 60 103 5 S-102 WIRE ARRANGEMENT ワイヤー整形図 If wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation. 調整や部品の交換等により、ワイヤー類の結束をはずしたり移 動させた場合には、それらの作業が完了した時点でワイヤーの 整形をおこなってください。正しく整形されてないとノイズ発 生の原因となることがあります。 1. ADV-S102 1. ADV-S102 ① Fasten the CW051 5P connector cord to the front chassis with a clamp band. ② Fasten the CW052 5P connector cord to the front chassis with a clamp band. ③ Fasten the CX31 3P connector cord to the circuit board with a style pin. ④ Fasten the CW52 5P connector cord to the circuit board with a style pin. ⑤ Press the CX211 FFC in with a style pin. ⑥ Twist the CX021 2P connector cord several times and fasten it twice with a style pin. ① CW051 5P コネクターコードをフロントシャーシにクラン プバンドで結束する。 ② CW052 5P コネクターコードをフロントシャーシにクラン プバンドで結束する。 ③ CX031 3P コネクターコードをスタイルピンで基板に固定 する。 ④ CW052 5P コネクターコードをスタイルピンで基板に固定 する。 ⑤ CX211 の FFC をスタイルピンで押さえこむ。 ⑥ CX021 2P コネクターコードを数回捩ってスタイルピンで 2 箇所を固定する。 CX021 CX301 CX151 CX052 CX171 CX211 CX051 CX031 CX061 CX051 CW052 ① ⑤ ④ ③ ⑥ ② ⑥ ⑥ CX061 6P コネクターコードをコードホルダーで固定す る。 ⑦ CX061 6P コネクターコードをスタイルピンで基板より浮 かせて固定する。 ⑥ Fasten the CX061 6P connector with a cord holder. ⑦ Float the CX061 6P connector code to the circuit board with a style pin and fasten. Ferrite Cramp CX061 CX061 ⑦ ⑧ 6 ⑦ S-102 2. DSW-S102 2. DSW-S102 ① Fasten the CX041 4P connector cord to the chassis with a clamp band. ② Fasten the CX041 4P connector cord and CX081 8P connector cord to the chassis with a clamp band. ③ Fasten with a clamp band. ④ Fasten the CX021 2P connector cord to the chassis with a clamp band. ① CX041 4P コネクターコードをクランプバンドでシャーシ に固定。 ② CX041 4P コネクターコードと CX081 8P コネクターコー ドをクランプバンドでシャーシに固定。 ③ クランプバンドで結束。 ④ CX021 2P コネクターコードをクランプバンドでシャーシ に固定。 ④ CX021 CX151 ③ CX041 CX081 ① ② CX022 7 S-102 DISASSEMBLY 各部のはずしかた (Follow the procedure below in reverse order when reassembling.) (組み立てるときは、逆の順序でおこなってください。) ● ADV-S102 1. ローダーパネルのはずしかた ● ADV-S102 1. Loader Panel (1) Switch on, and press [ to open the Disc tray. (1) 電源を入れ「 (OPEN/CLOSE)」ボタンを押して、 ディスクトレイを開きます。 (OPEN/CLOSE)] button (2) ローダーパネルを持ち上げてはずします。 (2) Detach the Loader Panel by lifting. 2. サイドパネルのはずしかた 2. Side Panel (1) 底面よりネジを 4 本はずします。 (1) Remove 4 bottom screws. (2) 裏面よりネジを 4 本はずし、サイドパネルを矢印 の方向へはずします。 (2) Remove 4 rear screws, then detach Side Panel. 8 S-102 3. Top Cover 3. トップカバーのはずしかた (1) Remove 9 screws, then detach Top Cover. (1) トップカバーを止めているネジ 9 本をはずし、 トップカバーを矢印の方向へはずします。 4. DVD Mecha. Unit 4. DVD メカユニットのはずしかた (1) Remove 4 screws fixing the DVD Mecha. (1) メカユニットを止めているネジ 4 本をはずしま す。 (2) Detach the DVD Mecha. to the arrow direction. (3) Lift the DVD Mecha. and disconnect FFC and connectors. (2) メカユニットを矢印の方向にはずします。 (3) DVD メカユニットを持ち上げ、コネクタと FFC をはずします。 (4) 9 S-102 5. Front Panel Ass’y 5. フロントパネルのはずしかた (1) Remove 6 Front panel screws, then detach P.W.B. and chassis. (1) フロントパネルからの基板とシャーシを止めてい るネジを 6 本はずします。 (2) Remove 4 Front panel side screws, then detach the Front Panel Ass’y. (2) フロントパネル側面を止めているネジ 4 本(左右 各 2 本)をはずし、フロントパネルをはずしま す。 6. Back Panel Ass’y 6. バックパネルのはずしかた (1) Remove each terminal screws, Back Panel screws and Chassis screws, then detach the Back Panel. (1) 各端子を止めているネジおよびバックパネルと シャーシを止めているネジをはずし、バックパネ ルをはずします。 10 S-102 ● DSW-S102 1. Rear panel ● DSW-S102 1. Rear panel (1) Remove 10 screws 101 on the bottom side. (1) 底面側から 101 のねじ 10 本をはずします。 (2) Detach the Rear panel. (2) Rear panel をはずします。 101 2. SHIELD COVER 2. SHIELD COVER (1) Remove 8 screws 103 on the Side. (1) 側面側から 103 のねじ 8 本をはずします。 (2) Lift the shield cover using a flat-headed screwdriver and remove it. When doing this, be careful not to deform the main bracket's hook. (2) マイナスドライバーでシールドカバーを持ち上げては ずします。このとき、メインブラケットのつめを変形 させないように注意してください。 103 103 103 11 S-102 DIAGNOSTICS OF OPTICAL PICKUP AND REPLACING TRAVERSE UNIT 光ピックアップの故障診断とトラバース ユニットの交換 Make failure diagnostics of the Optical Pickup as follows. If the laser drive current (Iop) becomes more than 1.5 times of the initial value, the Optical Pickup should be replaced. The laser drive current initial value is checked by "Iop checked Method" of next page. In case of replacing the Pickup, change the whole part of the Traverse Unit. No mechanical adjustment is necessary after the replacement. 次の順序で故障診断を行ってください。 レーザー駆動電流 Iop 値が初期値の 1.5 倍以上になっている 場合は光ピックアップ交換の目安となります。 レーザー駆動電流初期値は、次ページ "Iop 値の確認方法 " で 確認できます。 ピックアップ交換の場合は、トラバースユニット単位での交 換となります。メカの調整は不要です。 レーザー駆動電流初期値 : Laser drive current initial value: DVD: CD: FL Display (The display part of 13 digits) 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 2 ― m m m m ― n n n n FL Display (The display part of 13 digits) 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 1 ― m m m m ― n n n n ディスクを読み込まない スムーズに再生しない、等 Disc no read, unsteady playback, etc. Laser drive current (Iop) check HF wave form check (Refer to WAVE FORMS) レーザー駆動電流 Iop 値の確認 HF 波形の確認 (WAVE FORMS 参照) Present value exceeds the initial value by 1.5 times 現在値が初期値の 1.5 倍になっている Traverse Unit replacing トラバースユニット交換 Laser current (Iop) memorizing after replacement 交換後にレーザー電流値の記憶 12 S-102 1. Iop checked Method 1. Iop 値の確認方法 Select the laser ON/OFF (CD/DVD) mode of the test mode, and check the lop value of DVD laser or CD laser. (See page 13 for test mode.) レーザー駆動電流を確認する場合は、テストモードのレー ザー ON/OFF (CD/DVD) モードを選択して、DVD レーザー または CD レーザーの lop 値を確認します。 (詳細は 13 ページ、テストモード参照) FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) 1 2 T 2 3 4 5 6 7 8 9 10 11 12 13 1 2 L a s e r O n O f f T 2 1.1. DVD laser current check 3 4 5 6 7 8 9 10 11 12 13 L a s e r O n O f f 1.1. DVD レーザー電流確認 (1) Press the SKIP or button to display the laser current value, and then select T22. (2) Check the current value of Iop (nnnn). FL Display (The display part of 13 digits) (1) レーザー電流値を表示する場合は、 ボタンまたは ボタンを押し、T22 を選択します。 (2) 現在の lop 値 (nnnn) を確認します。 FL 管の表示 (13 桁の表示部 ) 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 2 ― m m m m ― n n n n ( − : Off, DVD laser, Initial value: mm.mm [mA], Current value: nn.nn [mA]) 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 2 ― m m m m ― n n n n ( −:消灯、DVD レーザー、初期値:mm.mm[mA], 現在値:nn.nn [mA]) 1.2. CD Laser current check 1.2. CD レーザー電流確認 (1) Press the or button to display the laser current value, and then select T21. (2) Check the current value of Iop (nnnn). (1) レーザー電流値を表示する場合は、 ボタンまたは ボタンを押し、T21 を選択します。 (2) 現在の lop 値 (nnnn) を確認します。 FL Display (The display part of 13 digits) 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 1 ― m m m m ― n n n n FL 管の表示 (13 桁の表示部 ) ( − : Off, CD laser, Initial value: mm.mm [mA], Current value: nn.nn [mA]) 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 1 ― m m m m ― n n n n ( −:消灯、CD レーザー、初期値:mm.mm[mA], 現在値:nn.nn[mA]) 2. Note for Handling the Laser Pick-Up 2. レーザーピックアップの取扱注意 レーザーダイオードの破壊防止。 光素子ユニットを交換するときは、以下を遵守してくださ い。 (1) 光素子ユニットの接続ケーブルをはずすときは、静電対 策を行ったデスク上で作業してください。 (2) 作業者は、リストストラップを使用してください。 (3) レーザーダイオードの破壊防止のため、24P FFC ケーブ ルをはずす前にランドを半田付けショートしてくださ い。 (4) 光素子ユニットのコネクタ部に触れないでください。 The protection for the damage of laser diode. If you want to change the optical device unit from any other units, you must keep the following. (1) It should be done at the desk already took measures the static electricity in care of removing the OPU's (Optical device unit) connector cable. (2) Workers should be put on the "Earth Band". (3) It should be done to add the solder to the short land to prevent the broken Laser diode before removing the 24P FFC cable. (4) Don't touch OPU's connector parts carelessly. 3. Replacement of the Laser Pick-up (Traverse Unit) 3. レーザーピックアップ ( トラバースユニッ ト ) の交換 Iop( レーザー駆動電流)をチェックします。 現在の Iop 値が初期値の 150%を越えている場合、 トラバー スユニット(レーザーピックアップ)を交換してください。 Check the Iop (Laser drive current) If the present Iop (current) value exceeds.+150% of the initial value, replace the Traverse unit (Laser Pick-up) with a new one. 13 S-102 4. Rewriting the default value of the laser current 4. レーザー電流初期値の書き換え方法 レーザー電流の初期値を書き換えるには、CD または DVD レーザー電流が表示されている時に ボタンを5秒以上押 し、次に ボタンまたは ボタンを押して T23 を 選択します。(詳細は 22 ページ、Iop 値の確認方法参照) To rewrite the default value of the laser current, press the button for at least 5 seconds while the CD or DVD laser current is displayed, then press the or button to select T23. (For details, see "Iop checked Method" on page 22.) If the button is pressed while T23 is displayed, the current value is displayed at "mmmm" and stored in the EEPROM. T23 表示時に ボタンを押と、mmmm 部に現在値を表示 し、EEPROM に保存します。 FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 3 ― m m m m ― ― ― ― ― 5. Resetting the accumulated laser on time 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 3 ― m m m m ― ― ― ― ― 5. レーザー ON 累積時間のリセット方法 To clear the accumulated laser on time, press the button while the accumulated laser on time is displayed (TB1, TB2 : For details, see "Test Mode" on page 22.) until " * " appears at the fourth position, then press the or button to select TB3. If the button is pressed while TB3 is displayed, the accumulated laser on time of CD and DVD is cleared. When TB1 or TB2 is selected with the or button, "nnnnnnn" is displayed as 0 so you can check. FL Display (The display part of 13 digits) レーザーON 累積時間をクリアするには、レーザーON 累 積時間表示 (TB1,TB2) の時(詳細は 22 ページ、テストモー ド参照)に ボタンを 4 桁目に ' * ' が表示されるまで押 し、 ボタンまたは ボタンを押し TB3 を表示させ ます。 TB3 表示時に ボタンを押すと、CD 及び DVD レーザー ON 累積時間をクリアします。 ボタンまたは ボタンで TB1 または TB2 を選択 すると、nnnnnnn 部が 0 表示となり確認できます。 FL 管の表示 (13 桁の表示部 ) 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 T B Y ― ― ― n n n n n n n T B Y ― ― ― n n n n n n n ( − : Off, Y:1: CD, 2: DVD, nnnnnnn: Hour [h]) ( −:消灯、Y:1: CD, 2: DVD、nnnnnnn:時間 [h]) 14 S-102 HOW TO REPLACE TRAVERSE UNIT Caution: The optical pickup can be damaged easily by static electricity charged on human body. Take necessary anti-static measures when repairing around the optical pickup. 1. Guide Clamp Bracket disassembly 注意 : 光ピックアップは、人体に帯電した静電気等で静電 破壊することがあります。光ピックアップ周辺を修 理する際は、必要な静電対策を行ってください。 3. トラバースユニットのはずしかた (1) Remove 24P FFC, 15P FFC and 5P PH WIRE connecting with from the Main P.W.B. (1) メイン基板に接続している 24P FFC、15P FFC、5P PH ワイヤをはずします。 (2) Remove 4 screws fixing Damper. (2) ダンパーを固定しているねじ 4 本をはずします。 (3) Remove Traverse Unit to arrow direction. (3) トラバースユニットを矢印方向にとりはずします。 1. ガイドクランプブラケットのはずしかた (1) Remove 2 screws. (1) ねじ 2 本をはずします。 (2) Remove Guide Clamp Bracket to arrow direction. (2) ガイドクランプブラケットを矢印方向にとりはずしま す。 2. Tray disassembly 3. Traverse Unit disassembly トラバースユニットの交換方法 2. トレイのはずしかた (1) Remove to arrow direction. (1) 矢印方向にとりはずします。 (2) Solder the short-circuit (see in the frame). (2) 半田付けショートを行います。(枠内図参照 ) 半田ショート Solder to short-circuit Note for disassembly Traverse Unit Short-circuit with Solder 半田ショート拡大図 15 トラバースユニット分解の注意 (1) When assembling, reverse the order of the above. (1) 組み立てるときは、上記の逆の順序で行ってください。 (2) When inserting Tray, confirm boss on Slide Cam set to ditch of the Tray (Compare with below drawing). (2) トレイ組込み時、スライドカムのボスがトレイの溝に 合っているか確認してください。(下図参照) S-102 SERVICE MODE サービスモードについて 1. Aging Mode 1. エージングモード 1.1. preparation0 1.1. 準備 (1) Equipment used: Any one of DVD Karaoke Disc (containing more than 10 titles). (ex : Heat run disc TDV-HR01) (1) 使用機器:DVD カラオケディスク (10 タイトル以上のもの) (例:ヒートランディスク TDV-HR01) (2) Unit setting : No spec other than the following procedure. (2) 本体設定:下記設定以外規定無。 1.2. procedure 1.2. 手順 ※ Perform aging of the DVD. ※ DVD のエージングをおこなう。 (1) Pressing the and buttons simultaneously, plug the AC cord into a power outlet, then press the ON/STANDBY button to turn the power on. This sets the aging mode. (1) 本体の ボタンと ボタンを同時に押しながら、AC コードをコンセントへ接続し、ON/STANDBY ボタンを押してセット の電源を入れると、エージングモードが設定される。 • Once the aging mode is set, press the FUNCTION button to switch the mode. (After the display is put out at the switch, it selects.) (a) To select the normal aging mode ... Start from (2) (b) To select the error rate display mode ... Start from (8) (2) Press the (3) Both the " (4) When the (5) The " ・ エージングモード設定後、FUNCTION ボタンを押して、モードを切り替える。 (切り替え時に表示を出してから選択する。) (a) 通常のエージングモードを選択・・・(2) から開始 (b) エラーレート表示モードを選択・・・(8) から開始 button and play all the tracks recorded on the disc. " and " (2) " indicators light on the fluorescent display tube. (3) FL 管の“ button is pressed once with the tray open, titles 1 and 10 recorded on the disc are played. " indicator flashes and the " ボタンを押し、ディスクに収録されている全ての曲を再生する。 ”インジケーターと“ (4) トレイを開いた状態で " indicator lights on the fluorescent display tube. (5) FL 管の“ ”インジケーターが両方とも点灯する。 ボタンを 1 回押して、ディスクに収録されているタイトル 1 とタイトル 10 を再生する。 ”インジケーターが点滅し、“ ”インジケーターが点灯する。 (6) Once playback is completed, open and close the tray and repeat the operation in step (3) or (4). (6) 再生終了後、トレイを開閉させ (3) または (4) の動作をする。 (7) If there is an error while in the aging mode, the error is displayed and the stop mode is set with the status at that time. (7) エージングモード中にエラーが発生すると、エラーを表示し、その時の状態で停止する。 注 )・ エージングモード中は、本体の FUNCTION ボタンおよび、リモコンの FUNCTION 切替ボタンは動作しない。 (ファンクッションを変えると DVD が停止し、エージングモードが解除される。) ・ エージングモード中は本体およびリモコンの ON/STANDBY ボタンを動作しない。 (セットの電源を OFF にすると DVD が停止し、エージングモードが解除される。) NOTE) ・The FUNCTION button on the main unit and the FUNCTION selector button on the remote control unit will not work during the aging mode. (If the function is switched, the DVD stops and the aging mode is canceled.) ・The ON/STANDBY buttons on the main unit and the remote control unit will not work during the aging mode. (If the set's power is turned off, the DVD stops and the aging mode is canceled. (8) When the error rate display mode is set, the final error rate information is displayed on the fluorescent display tube. No. Error contents 1 Bad DIsc 2 Forcus Error 3 Read Error 4 Tracking Error 5 Tray Error 6 Navigation Pack Read Error 7 Cmmunication Error (8) エラーレート表示モードに入ると、最終エラーレート情報を FL 管に表示する。 No. FL display FL Display (The display part of 13 digits) 1 2 3 E 7 4 5 6 7 X X 8 9 10 X X 11 エラー内容 1 不良ディスク 2 フォーカスエラー 3 リードエラー 4 トラッキングエラー 12 13 5 トレイエラー X X 6 ナビゲーションパックエラー 7 コマンド通信エラー 16 FL 管表示 FL 管の表示 (13 桁の表示部 ) 1 2 3 E 7 4 5 6 7 X X 8 9 10 X X 11 12 13 X X S-102 2. Initial Setting Mode 2. イニシャルモード 2.1. Preparation 2.1. 準備 (1) Equipment used: None (1) 使用機器:無 (2) Unit setting: No spec other than the following procedure. (2) 本体設定:下記手順以外規定無。 2.2. Procedure 2.2. 手順 ● SYSTEM ● システム ※ This initializes the data for the function, volume, DVD mechanism, etc. ※ ファンクション、VOL 等および DVD メカのバックアップデータの初期化をおこなう。 (1) When the ON/STANDBY button is pressed to turn the set on while pressing the main unit's FUNCTION and simultaneously, the initialization mode is set. buttons (1) 本体 FUNCTION ボタン と ルモードが設定される。 ボタンを同時に押しながら、ON/STANDY ボタンを押してセットの電源を入れるとイニシャ (2) The standby indicator lights yellow and "INITIALIZE" is displayed on the fluorescent display tube. (2) スタンバイ LED が黄色に点灯し、FL 管に“INITIALIZE”が表示される。 (3) Once the entire initialization procedure has been completed, the set is in the normal mode with the power turned on. (3) 全ての初期化完了後、通常モードの電源 ON の状態になる。 ● DVD ● DVD ※ This initializes the data for the DVD mechanism. (1) With the power on, set the function to DVD, and in the playback stopped mode, press the for at least 2 seconds to set the DVD initialization mode. ※ DVD のみのバックアップデータの初期化をおこなう。 and buttons simultaneously (1) 電源 ON 時にファンクッションを DVD にし再生停止状態で、 ボタンと DVD 初期化モードが設定される。 (2) "INITIALIZE" is displayed on the fluorescent display tube. ボタンを 2 秒以上同時に押し続けると、 (2) FL 管に“INITIALIZE”が表示される。 3. µcom Firm Check Mode 3. マイコンファームチェックモード 3.1. Preparation 3.1. 準備 (1) Equipment used: None (1) 使用機器:無 (2) Unit setting: No spec other than the following procedure. (2) 本体設定:下記手順以外規定無。 3.2. Procedure 3.2. 手順 ※ Use this to display the version information, etc. ※ バージョン表示等をおこなう。 (1) When, in the standby mode, the ON/STANDBY button is pressed to turn the set on while pressing the main unit's FUNCTION and buttons simultaneously, the system check mode is set. (1) STANDBY 時に本体 FUNCTION ボタンと ボタンを同時に押しながら、ON/STANDBY ボタンを押してセットの電源を入 れると、システムチェックモードが設定される。 (2) Press the STATUS button on the remote control unit to display the following information, in this order: System microprocessor version → Date of system microprocessor version updating → DSP version → Date of DSP version updating → Drive microprocessor version of DVD mechanism → ESS version → Date of ESS version updating. (2) リモコンの STATUS ボタンを押すと、システムマイコンのバージョン→システムマイコンのバージョンアップ日→ DSP の バージョン→ DSP のバージョンアップ日→ DVD メカのドライブマイコンのバージョン→ ESS のバージョン→ ESS のバー ジョンアップ日の順に表示される。 (3) Unplug AC cord to clear this mode. (3) AC コードを抜くことにより、システムチェックモードを解除する。 NOTE) The DVD mechanism driver version and ESS version are not displayed un less the function is once set to DVD. 注 ) DVD メカのドライブバージョン、ESS のバージョンの表示については、一度ファンクッションを DVD にしないと表示 されない。 17 S-102 4. Test mode 4. テストモード 4.1. Entering the test mode 4.1. テストモードの設定 To enter the test mode, press the and buttons simultaneously while in the Aging mode. Not insert the disc. (The Aging mode is entered by pressing the and buttons simultaneously to turn on the AC power. When the Aging mode is set, the and indicators light.) Press and テストモードの設定はエージングモード時に ボタンと ボタンを同時に押すことでおこなう。ディスクは挿入していな いこと。 ( エージングモードの設定は ボタンと ボタンを同時に押しながら、AC コードをコンセントへ接続し、セットの電源を入れ る。エージングモードになると FL 管の“ ”インジケーターと“ ”インジケーターが点灯する。) buttons simultaneously ボタンと ボタンの同時押し Power turns on 電源 ON Press and Aging mode buttons simultaneously ボタンと Test mode エージングモード ボタンの同時押し button テストモード ボタン Set the disc button ディスクを載せる ボタン Set the disc button ディスクを載せる Aging mode start button TOC リード後 ボタン Test mode start テストモード開始 テストモード設定時の FL 管表示 FL tube display when test mode entered FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) 2 3 4 5 6 T E S T 7 8 9 10 11 M O D E 12 1 13 The following modes are available. (1) Laser on/off (CD/DVD) mode (2) Servo adjustment value display mode (3) Trace mode (error rate display) (4) Accumulated laser on time : : : : T 2 3 2 T 3 3 4 5 6 7 8 9 10 11 12 13 L a s e r O n O f f 2 T 7 3 4 5 6 7 8 S e r v o 9 10 11 12 A d j 13 2 T B 3 T E S T 7 8 9 10 11 M O D E 12 13 : : : : T2 T3 T7 TB ボタンを押すと、T2,T3,T7,TB,T2…の順に表示される。 1 2 T 2 3 4 5 6 7 8 9 10 11 12 13 L a s e r O n O f f 1 2 T 3 3 4 5 6 7 8 9 10 11 12 13 S e r v o A d j 4 5 6 7 8 10 11 12 13 T r a c e M o d e 4 5 6 7 8 9 10 11 12 13 L a s e r O n T i m FL 管の表示 (13 桁の表示部 ) 4 5 6 7 8 T r a c e 9 10 11 12 13 M o d e 1 2 T 7 3 9 FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) 1 6 FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) 1 5 FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) 1 4 ①テストモード中に FL Display (The display part of 13 digits) 2 3 モードには、次のモードがある。 (1) レーザー ON/OFF(CD/DVD) モード (2) サーボ調整値表示モード (3) トレースモード ( エラーレート表示 ) (4) レーザー ON 累積時間 T2 T3 T7 TB button is pressed after entering the test mode, the display switches in the order: T2, T3, T7, TB, T2 … 1 2 4.2. モードの選択 4.2. Selecting the mode ① When the エージング開始 ボタン After the TOC reading button 1 ボタン 4 5 6 7 8 9 10 11 12 13 L a s e r O n T i m 18 1 2 T B 3 S-102 4.3. Setting the mode 4.3. モードの確定 With the mode selected, press the button to set that mode. モードを選択してある状態で ① In the laser on/off (CD/DVD) mode, laser on/off control is executed and the laser current is displayed. Press the or button to switch the CD/DVD (T21, T22, T21. .). To save the current laser current value, press and hold in the button for at least 5 seconds to turn off the "mmmm" section of the display, then press the or button and select T23. When the button is pressed while T23 is displayed, the data is displayed in the "mmmm" section. ボタンを押すとモードを確定する。 ①レーザー ON/OFF(CD/DVD) モードの場合、レーザーの ON/OFF 制御を実行し、レーザー電流を表示する。CD/DVD の切り替 えは、 ボタンまたは ボタンを押す (T21、T22、T21. .)。 現在のレーザー電流値を保存する場合、 ボタンを 5 秒以上押し続け、mmmm 部を非表示にし、 ボタンまたは ボタンを押して、T23 を選択する。T23 を表示時に ボタンを押すと、mmmm 部にデータが表示される。 CD レーザーの場合 For the CD laser FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 1 ― m m m m ― n n n n 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 1 ― m m m m ― n n n n ( −:消灯、CD レーザー、保存データ:mm.mm[mA], 現在値:nn.nn[mA]) ( − : Off, CD laser, Stored data: mm.mm [mA], Current value: nn.nn [mA]) DVD レーザーの場合 For the DVD laser FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 2 ― m m m m ― n n n n 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 2 ― m m m m ― n n n n ( −:消灯、DVD レーザー、保存データ:mm.mm[mA], 現在値:nn.nn [mA]) ( − : Off, DVD laser, Stored data: mm.mm [mA], Current value: nn.nn [mA]) ②サーボ調整値表示モードの場合 (表 1 サーボ調整値表示モード詳細 参照) ② In the servo adjustment value display mode (See "Table 1 - Servo adjustment value display mode details") FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) 1 2 3 4 5 6 7 8 9 10 11 12 13 T X X − − − − − − n n n n 1 2 3 4 5 6 7 8 9 10 11 12 13 T X X ― ― ― ― ― ― n n n n (XX: 選択モード、n: 調整値 (HEX)) (XX : Selection mode, n : Adjustment value (HEX)) ③トレースモード ( エラーレート表示 ) の場合は、1層内周のトレースを選択する。 ③ In the trace mode (error rate display), select the trace of the innermost circumference of 1 layer. FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) 1 2 3 4 5 6 7 8 9 10 11 12 13 T 7 1 F F F F F F F F F F 1 2 3 4 5 6 7 8 9 10 11 12 13 T 7 1 F F F F F F F F F F (F: アドレス及びエラーレートは未確定時、F を表示する。) (F : When address and error rate not set, F is displayed.) ④レーザー ON 累積時間 (EEPROM に記憶 ) を表示する。 ④ Displaying the accumulated laser on time (stored in the EEPROM) FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) 1 2 3 4 5 6 7 8 9 10 11 12 13 T B Y ― ― ― n n n n n n n 1 2 3 4 5 6 7 8 9 10 11 12 13 T B Y ― ― ― n n n n n n n (Y:1: CD、2: DVD、nnnnn : 時間 [h]) ※ 1 時間未満は切り上げて表示する。 (Y : 1:CD, 2:DVD, nnnnn: Time [h]) ※ Fractions of hours are counted up one hour on the display. 19 S-102 4.4. Change within the mode 4.4. モード内での変更 Changes within modes are made by pressing the and buttons while the mode is set. モードを確定してある状態で ① In the laser on/off (CD/DVD) mode, laser on/off control is executed and the laser current is displayed. ボタンまたは ボタンを押すとモード内での変更をおこなう。 ①レーザー ON/OFF(CD/DVD) モードの場合、レーザーの ON/OFF 制御を実行し、レーザー電流を表示する。 For the CD laser CD レーザーの場合 FL Display (The display part of 13 digits) FL 管の表示 (13 桁の表示部 ) 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 1 ― m m m m ― n n n n T 2 1 ― m m m m ― n n n n ( − : Off, CD laser, Stored data: mm.mm [mA], Current value: nn.nn [mA]) ( −:消灯、CD レーザー、保存データ:mm.mm[mA], 現在値:nn.nn[mA]) For the DVD laser DVD レーザーの場合 FL Display (The display part of 13 digits) FL 管の表示 (13 桁の表示部 ) 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 2 ― m m m m ― n n n n T 2 2 ― m m m m ― n n n n ( − : Off, DVD laser, mm.mm [mA], nn.nn [mA]) ( −:消灯、DVD レーザー、mm.mm[mA], nn.nn[mA]) When there is no saved data (for the DVD laser) 保存データなしの場合 (DVD レーザーの場合 ) FL Display (The display part of 13 digits) FL 管の表示 (13 桁の表示部 ) 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 2 ― ― ― ― ― ― n n n n T 2 2 ― ― ― ― ― ― n n n n ( − : Off, DVD laser, nn.nn [mA]) ( −:消灯、DVD レーザー、nn.nn[mA]) To store the current value, press the button for at least 5 seconds, then press the or button to select T23. If the button is pressed while T23 is displayed, the current value is displayed at "mmmm" and stored in the EEPROM. 現在地を保存するには、 ボタンを 5 秒以上押し、次に ボタンまたは ボタンを押して、T23 を選択する。T23 表 示時に、 ボタンを押すと、mmmm 部に現在値を表示し、EEPROM に保存される。 FL Display (The display part of 13 digits) FL 管の表示 (13 桁の表示部 ) 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 T 2 3 ― m m m m ― n n n n T 2 3 ― m m m m ― ― ― ― ― ( − : Off, DVD laser, nn.nn [mA]) If the current value is over 100 mA, the 4th and 9th digit sections are used. ( −:消灯、DVD レーザー、mm.mm[mA]) 電流値が 100mA 以上の場合は、4 桁、9 桁部分を使用。 ② In the servo adjustment value display mode (See "Table 1 - Servo adjustment value display mode details") ②サーボ調整値表示モードの場合 (表 1 サーボ調整値表示モード詳細 参照) FL Display (The display part of 13 digits) FL 管の表示 (13 桁の表示部 ) 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 T X X ― ― n n n n n n n n T X X ― ― n n n n n n n n (XX : Selection mode, n: Adjustment value (HEX)) For the adjustment values, 0's are added in front of the effective number of bytes. (Ex.: If the value is 0x123 for 4-byte data, "00 00 01 23" is displayed.) (XX: 選択モード、n: 調整値 (HEX)) 調整値は、有効バイト数分先頭に 0 をつける。 (例:4 バイトデータで値が 0x123 の場合は“00 00 01 23”) ⑤ In the trace mode (error rate display) (See "Table 2 - Trace mode details") ③トレースモード ( エラーレート表示 ) の場合( 表 2 トレースモード詳細 参照) FL Display (The display part of 13 digits) FL 管の表示 (13 桁の表示部 ) 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 T Y Y F F F F F F F F F F T Y Y F F F F F F F F F F (YY : Selection mode [71 to 94], F: When address and error rate not set, F is displayed.) (YY: 選択モード [71 ∼ 94]、F: アドレス及びエラーレートは未確定時、F を表示する。) ⑥ In the accumulated laser on time display ⑥レーザー ON 累積時間を表示場合 FL Display (The display part of 13 digits) FL 管の表示 (13 桁の表示部 ) 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 T B Y ― ― ― n n n n n n n T B Y ― ― ― n n n n n n n (Y : 1: CD, 2: DVD, nnnnnnn: Time [h]) ※ If the current value is over 100 mA, the 4th and 9th digit sections are used. To clear the accumulated laser on time, press the button while the accumulated laser on time is displayed (TB1, TB2) until " * " appears at the fourth position, then press the or button to select TB3. If the PLAY button is pressed while TB3 is displayed, the accumulated laser on time of CD and DVD is cleared. When TB1 or TB2 is selected with the or button, "nnnnnnn" is displayed as 0 so you can check. (Y:1: CD, 2: DVD、nnnnnn: 時間 [h]) ※ 1 時間未満は切り上げて表示する。 レーザー ON 累積時間をクリアする場合、レーザー ON 累積時間表示時 (TB1、TB2) のとき、 ボタンを 4 桁目に“*”が表 示されるまで押し、 ボタンまたは ボタンを押し、TB3 を表示させる。TB3 表示時に ボタンを押すと CD および DVD レーザー ON 累積時間をクリアする。 ボタンまたは ボタンを押して、TB1 または TB2 を選択すると、 nnnnnn 部が 0 表示になり確認できる。 20 S-102 4.5. Execution of trace mode (error rate display) (See "Table 2 - Trace mode details") Trace will be performed if the 4.5. トレースモード ( エラーレート表示 ) の実行( 表 2 トレースモード詳細 参照) button is pushed after choosing operation. 動作を選択した後、 FL Display (The display part of 13 digits) ボタンを押すとトレースを実行する。 FL 管の表示 (13 桁の表示部 ) 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 T Y Y m m m m m m l l l l T Y Y m m m m m m l l l l (YY : selection mode [71 to 94], m : address [PBA][HEX], l : error rate [COUNT/SEC] [HEX]) Note) CD : Error rate of 75 frames is displayed (1 second). DVD : Error rate of 8ECC block is displayed. The mode chosen when selection mode was changed into the trace execution and the button was pushed is performed from the beginning. When the button is pushed without changing selection mode, the mode under selection is performed from the beginning. (If the button is pushed, the address corresponding to the chosen mode will be searched again.) (YY: 選択モード [71 ∼ 94]、m: アドレス [PBA][HEX]、l: エラーレート [COUNT][DEC]) 注 ) CD : 表示するエラーレートは、75 フレーム分の値 (1 秒 )。 DVD : 表示するエラーレートは、8ECC ブロック分の値。 トレース実行中に選択モードを変更し、 ボタンを押すと選択したモードを最初から実行する。 選択モードを変更せずに ボタンを押した場合も、選択中のモードを最初から実行する。 ( ボタンを押すと、選択しているモードに対応したアドレスを再度サーチする。) トレース終了時は、PAUSE 状態になります。 The pause mode is set after tracing is completed. 4.6. Other operations ① When the 4.6. その他の動作 button is pressed, the mode returns to the previously selected mode. ① (1) Test mode detailed table ボタンを押すと、前の選択モードに戻る。 (1) テストモード詳細一覧表 Table 1: Servo adjustment value display mode details 表 1 サーボ調整値表示モード詳細 XXX Name Size Meaning Remarks XXX 名称 サイズ T31 fbal0 16bits CD/DVD L0 layer focus balance adjustment value FBAL range: 0x8000 < FBAL < 0x7FC0(Center:0x0000) T31 fbal0 16 ビット T32 tbal0 16bits CD/DVD L0 layer tracking balance adjustment value TBAL range: 0x0000 < TBAL < 0x003F T32 tbal0 16 ビット CD/DVD L0 層トラッキングバランス調整値 T33 fcga0 16 ビット CD/DVD L0 層フォーカス Loop Gain 調整値 0x100 で 1 倍 [0x200(2 倍 ) を Typ に設定する ] (0x100 で 1 倍、0x200 で 2 倍。Y/0x100 の比率計算) 調整値 0x200 で Gain 交点が目標ターゲットになる様設定している。 T34 tkga0 16 ビット CD/DVD L0 層トラッキング Loop Gain 調整値 0x100 で 1 倍 [0x200(2 倍 ) を Typ に設定する。] (0x100 で 1 倍、0x200 で 2 倍。Y/0x100 の比率計算) 調整値 0x202 で Gain 交点が目標ターゲットになる様設定している。 T35 Fbal1 16 ビット DVD L1 層フォーカスバランス調整値 意 味 CD/DVD L0 層フォーカスバランス調整値 備 考 FBAL の範囲は 0x8000< FBAL<0x7FC0。( センター : 0x0000) TBAL の範囲は 0x0000< TBAL<0x003F。 T33 fcga0 16bits CD/DVD L0 layer focus Loop Gain adjustment value 1x for 0x100 [0x200 (2x) set to Typ. (1x for 0x100, 2x for 0x200. Y/0x100 ratio calculation.) Adjustment value 0x200 sets so that gain crossover reaches target. T34 tkga0 16bits CD/DVD L0 layer tracking Loop Gain adjustment value 1x for 0x100 [0x200 (2x) set to Typ. (1x for 0x100, 2x for 0x200. Y/0x100 ratio calculation.) Adjustment value 0x202 sets so that gain crossover reaches target. T35 Fbal1 16bits DVD L1 layer focus balance adjustment value FBAL range: 0x8000 < FBAL < 0x7FC0(Center:0x0000) T36 Tbal1 16 ビット DVD L1 層トラッキングバランス調整値 T36 Tbal1 16bits DVD L1 layer tracking balance adjustment value TBAL range: 0x0000 < TBAL < 0x003F T37 Fcga1 16 ビット DVD L1 層フォーカス Loop Gain 調整値 T37 Fcga1 16bits DVD L1 layer focus Loop Gain adjustment value 1x for 0x100 [0x200 (2x) set to Typ. (1x for 0x100, 2x for 0x200. Y/0x100 ratio calculation.) Adjustment value 0x200 sets so that gain crossover reaches target. 0x100 で 1 倍 [0x200(2 倍 ) を Typ に設定する ] (0x100 で 1 倍、0x200 で 2 倍。Y/0x100 の比率計算) 調整値 0x200 で Gain 交点が目標ターゲットになる様設定している。 T38 Tkga1 16 ビット DVD L1 層トラッキング Loop Gain 調整値 T38 Tkga1 16bits DVD L1 layer tracking Loop Gain adjustment value 1x for 0x100 [0x200 (2x) set to Typ. (1x for 0x100, 2x for 0x200. Y/0x100 ratio calculation.) Adjustment value 0x202 sets so that gain crossover reaches target. 0x100 で 1 倍 [0x200(2 倍 ) を Typ に設定する ] (0x100 で 1 倍、0x200 で 2 倍。Y/0x100 の比率計算) 調整値 0x202 で Gain 交点が目標ターゲットになる様設定している。 T39 Asoffs 16 ビット AS 信号の Offset 値 T40 Envoffse 16 ビット ENV 信号の Offset 調整値 上位 10bit が有効 T41 Foffse 16 ビット FE 信号の Offset 調整値 上位 10bit が有効 T42 Teoffse 16 ビット TE 信号の Offset 調整値 上位 10bit が有効 T43 RFfc 8 ビット RF 信号の周波数調整値 T44 RFbst 8 ビット RF 信号の Boost 調整値 T45 RFgdl 8 ビット RF 信号の低域群遅延調整値 T46 RFgdh 8 ビット RF 信号の高域群遅延調整値 T39 Asoffs 16bits AS signal Offset value Upper 10 bit is valid T40 Envoffse 16bits ENV signal Offset adjustment value Upper 10 bit is valid T41 Foffse 16bits FE signal Offset adjustment value Upper 10 bit is valid T42 Teoffse 16bits TE signal Offset adjustment value T43 RFfc 8bits RF signal frequency adjustment value T44 RFbst 8bits RF signal Boost adjustment value T45 RFgdl 8bits RF signal low range group delay adjustment value T46 RFgdh 8bits RF signal high range group delay adjustment value Upper 10 bit is valid Adjustment range : 0x0000 ∼ 0x001F 0x0000 : 0dB 0x001F : 14dB 21 FBAL の範囲は 0x8000< FBAL<0x7FC0。( センター :0x0000) TBAL の範囲は 0x0000< TBAL<0x003F。 上位 10bit が有効 調整範囲 : 0x0000 ∼ 0x001F 0x0000 : 0dB 0x001F : 14dB S-102 Table 2: Trace mode details 表 2 トレースモード詳細 YY Contents Contents supplement 71 A display of PO error detection number of the inner circumference of 1-layer and an address. It is invalid at the time of CD operation. 71 1 層内周の PO 誤り検出数とアドレスの表示 CD 時は無効。 72 A display of PO uncorrectable number of the inner circumference of 1-layer and an address. It is invalid at the time of CD operation. 72 1 層内周の PO 訂正不可数とアドレスの表示 CD 時は無効。 73 A display of PI error detection number of the inner circumference of 1-layer and an address. CD : C1 error detection number (x3) 73 1 層内周の PI 誤り検出数とアドレスの表示 CD 時は C1 誤り検出数。(x3) 74 A display of PI uncorrectable number of the inner circumference of 1-layer and an address. It is invalid at the time of CD operation. 74 1 層内周の PI 訂正不可数とアドレスの表示 CD 時は無効。 75 A display of PO error detection number of the central circumference of 1-layer and an address. It is invalid at the time of CD operation. 75 1 層中周の PO 誤り検出数とアドレスの表示 CD 時は無効。 76 A display of PO uncorrectable number of the central circumference of 1-layer and an address. It is invalid at the time of CD operation. 76 1 層中周の PO 訂正不可数とアドレスの表示 CD 時は無効。 77 A display of PI error detection number of the central circumference of 1-layer and an address. CD : C1 error detection number (x3) 77 1 層中周の PI 誤り検出数とアドレスの表示 CD 時は C1 誤り検出数。(x3) 78 A display of PI uncorrectable number of the central circumference of 1-layer and an address. It is invalid at the time of CD operation. 78 1 層中周の PI 訂正不可数とアドレスの表示 CD 時は無効。 79 A display of PO error detection number of the outer circumference of 1-layer and an address. It is invalid at the time of CD operation. 79 1 層外周の PO 誤り検出数とアドレスの表示 CD 時は無効。 80 A display of PO uncorrectable number of the outer circumference of 1-layer and an address. It is invalid at the time of CD operation. 80 1 層外周の PO 訂正不可数とアドレスの表示 CD 時は無効。 81 A display of PI error detection number of the outer circumference of 1-layer and an address. CD : C1 error detection number (x3) 81 1 層外周の PI 誤り検出数とアドレスの表示 CD 時は C1 誤り検出数。(x3) 82 A display of PI uncorrectable number of the outer circumference of 1-layer and an address. It is invalid at the time of CD operation. 82 1 層外周の PI 訂正不可数とアドレスの表示 CD 時は無効。 83 A display of PO error detection number of the inner circumference of 2-layer and an address. In the case of 1-layer DVD and CD disc, it is invalid. 83 2 層内周の PO 誤り検出数とアドレスの表示 DVD 1 層ディスクの場合、無効。 CD 時は無効。 84 A display of PO uncorrectable number of the inner circumference of 2-layer and an address. In the case of 1-layer DVD and CD disc, it is invalid. 84 2 層内周の PO 訂正不可数とアドレスの表示 DVD 1 層ディスクの場合、無効。 CD 時は無効。 85 A display of PI error detection number of the inner circumference of 2-layer and an address. In the case of 1-layer DVD disc, it is invalid. CD : C1 error detection number (x6) 85 2 層内周の PI 誤り検出数とアドレスの表示 DVD 1 層ディスクの場合、無効。 CD 時は C1 誤り検出数。(x6) 86 A display of PI uncorrectable number of the inner circumference of 2-layer and an address. In the case of 1-layer DVD and CD disc, it is invalid. 86 2 層内周の PI 訂正不可数とアドレスの表示 DVD 1 層ディスクの場合、無効。 CD 時は無効。 87 A display of PO error detection number of the central circumference of 2-layer and an address. In the case of 1-layer DVD and CD disc, it is invalid. 87 2 層中周の PO 誤り検出数とアドレスの表示 DVD 1 層ディスクの場合、無効。 CD 時は無効。 88 A display of PO uncorrectable number of the central circumference of 2-layer and an address. In the case of 1-layer DVD and CD disc, it is invalid. 88 2 層中周の PO 訂正不可数とアドレスの表示 DVD 1 層ディスクの場合、無効。 CD 時は無効。 89 A display of PI error detection number of the central circumference of 2-layer and an address. In the case of 1-layer DVD disc, it is invalid. CD : C1 error detection number (x6) 89 2 層中周の PI 誤り検出数とアドレスの表示 DVD 1 層ディスクの場合、無効。 CD 時は C1 誤り検出数。(x6) 90 A display of PI uncorrectable number of the central circumference of 2-layer and an address. In the case of 1-layer DVD and CD disc, it is invalid. 90 2 層中周の PI 訂正不可数とアドレスの表示 DVD 1 層ディスクの場合、無効。 CD 時は無効。 91 A display of PO error detection number of the outer circumference of 2-layer and an address. In the case of 1-layer DVD and CD disc, it is invalid. 91 2 層外周の PO 誤り検出数とアドレスの表示 DVD 1 層ディスクの場合、無効。 CD 時は無効。 92 A display of PO uncorrectable number of the outer circumference of 2-layer and an address. In the case of 1-layer DVD and CD disc, it is invalid. 92 2 層外周の PO 訂正不可数とアドレスの表示 DVD 1 層ディスクの場合、無効。 CD 時は無効。 93 A display of PI error detection number of the outer circumference of 2-layer and an address. In the case of 1-layer DVD disc, it is invalid. CD : C1 error detection number (x6) 93 2 層外周の PI 誤り検出数とアドレスの表示 DVD 1 層ディスクの場合、無効。 CD 時は C1 誤り検出数。(x6) 94 A display of PI uncorrectable number of the outer circumference of 2-layer and an address. In the case of 1-layer DVD and CD disc, it is invalid. 94 2 層外周の PI 訂正不可数とアドレスの表示 DVD 1 層ディスクの場合、無効。 CD 時は無効。 YY 22 内容 補足説明 S-102 TROUBLE SHOOTING トラブルシューティング ● ADV-S102 ● ADV-S102 トラブルシューティング 1. 1U-3836 (MAIN UNIT) 1.1. FL管点灯せず 1. 1U-3836 (MAIN UNIT) 1.1. FL TUBE dosen't light (1) Check the Set-up process of System μ-COM Check Power Supply Voltages. 1U-3836-1(MAIN UNIT) 䊶 [IC303]: +9V_DNS (1) システムμ-COM 立ち上がりチェック工程 N.G 電源電圧確認 1U-3836-1(MAIN UNIT) ・ [IC303]: +9V_DNS Check Soldering. 䊶 CX142 on MAIN UNIT. O.K. Check Power Supply Voltages. 1U-3836-1(MAIN UNIT) 䊶 [IC301]: +3.3V_DNS N.G 電源電圧確認 1U-3836-1(MAIN UNIT) ・ [IC301]: +3.3V_DNS Check Soldering. 䊶 IC303 on MAIN UNIT. N.G 発振波形確認 1U-3836-1(MAIN UNIT) ・ [IC301]: 16MHz at 18pin. Check Soldering. 䊶 X301 on MAIN UNIT. N.G 電源電圧確認 1U-3836-1(MAIN UNIT) ・ [IC301]: "H"level at [ON/STBY]15pin and "L"LEVEL at [CHOP_ON]48pin? Check Soldering. 䊶 IC301 on MAIN UNIT. N.G 電源電圧確認 1U-3836-1(MAIN UNIT) ・ [IC306]: +12V_M1 Check Soldering. 䊶 IC306 on MAIN UNIT. 半田付けを確認 ・ MAIN UNITのX301 N.G 半田付けを確認 ・ MAIN UNITのIC301 N.G 半田付けを確認 ・ MAIN UNITのIC306 N.G 半田付けを確認 ・ MAIN UNITのT201 N.G (1) MAIN UNITのCX211の半田付けを確認 (2) 1U-3831-1 の不良 O.K. N.G 電源電圧確認 1U-3836-1(MAIN UNIT) ・ [CX211]:19pin -HB=-35V±3V Check Soldering. 䊶 T201 on MAIN UNIT. O.K. Check Data Bus between 1U-3831-1(DISPLAY CENTER UNIT) FLD Driver(1U-3831-1[IC241]) 䊶 [FL_RST]:"H"level? N.G O.K. O.K. Check Power Supply Voltages. 1U-3836-1(MAIN UNIT) 䊶 [CX211]:19pin -HB=-35V±3䌖 半田付けを確認 ・ MAIN UNITのIC303 O.K. O.K. Check Power Supply Voltages. 1U-3836-1(MAIN UNIT) 䊶 [IC306]: +12V_M1 N.G O.K. O.K. Check Power Supply Voltages. 1U-3836-1(MAIN UNIT) 䊶 [IC301]: "H"level at [ON/STBY]15pin and "L"LEVEL at [CHOP_ON]48pin? 半田付けを確認 ・ MAIN UNITのCX142 O.K. O.K. Check Oscillation waveform. 1U-3836-1(MAIN UNIT) 䊶 [IC301]: 16MHz at 18pin. N.G O.K. N.G データバスの確認 1U-3831-1(DISPLAY CENTER UNIT) FLD Driver(1U-3831-1[IC241]) ・ [FL_RST]:"H"level? (1) Check soldering of CX211 on MAIN UNIT. (2) 1U-3831-1 is N.G.(No Good). O.K. O.K. Continue to next step. Check the Set-up process of B/E μ-COM. 次のステップへ (2)B/E μ-COM 立ち上げチェック工程へ 23 S-102 (2) Check the Set-up process of B/E μ-COM Check Power Supply Voltages. 1U-3836-1(MAIN UNIT) ・ [IC101]: +3.3V_D2,+2.0V_ESS O.K.? (2) B/E μ-COM 立ち上がりチェック工程 N.G 電源電圧確認 1U-3836-1(MAIN UNIT) ・ [IC101]: +3.3V_D2,+2.0V_ESS O.K.? Check Soldering. ・ [IC304] ・ [IC111] N.G Check 27MHz(3.3V)at 4pin of IC109. N.G O.K. クロックの波形確認 1U-3836-1(MAIN UNIT) ・ [IC101]:49,105,116pin and 117pin. 27MHz(3.3V),O.K.? (1) Check Soldering. of X101. (2) Check Soldering. of IC109 Check Soldering. Of ・ R202 N.G RESET信号の確認 1U-3836-1(MAIN UNIT) ・ [IC101]:[BE_RST]24 pin. "H"level O.K.? Check Soldering. ・ IC301,R112 N.G 半田付けを確認 ・ IC301,R112 N.G 半田付けを確認 1U-3836-1(MAIN UNIT) ・ [IC104] N.G 半田付けを確認 1U-3836-1(MAIN UNIT) ・ [LD0-LD7],[LCS3,LOE] N.G 半田付けを確認 ・ IC105 O.K. N.G 1U-3836-1(MAIN UNIT) [IC101]と[1C102]と[IC103]間の アドレス、データバスの確認 Check Soldering at Address,Data Bus,Control Signal. 1U-3836-1(MAIN UNIT) ・ [LD0-LD7],[LCS3,LOE] O.K. O.K. Check controll signal. 1U-3836-1(MAIN UNIT) ・ [IC105]:[BE_ON]19 pin. "H"level O.K.? N.G I2C信号の確認 1U-3836-1(MAIN UNIT) ・ [IC101]: "H"level at 160pin and 161pin. Check Soldering. 1U-3836-1(MAIN UNIT) ・ [IC104] O.K. 1U-3836-1(MAIN UNIT) Check Address,Data Bus between [IC101],[1C102]and[IC103] クロックの波形確認 ・ [IC109]:4pin O.K. O.K. Check I䋲C Signal. 1U-3836-1(MAIN UNIT) ・ [IC101]: "H"level at 160pin and 161pin. N.G O.K. O.K. Check Reset signal. 1U-3836-1(MAIN UNIT) ・ [IC101]:[BE_RST]24 pin. "H"level O.K.? 半田付けを確認 ・ [IC304] ・ [IC111] O.K. O.K. Check Clock waveform. 1U-3836-1(MAIN UNIT) ・ [IC101]:49,105,116pin and 117pin. 27MHz(3.3V),O.K.? N.G N.G 制御信号の確認 1U-3836-1(MAIN UNIT) ・ [IC105]:[BE_ON]19 pin. "H"level O.K.? Check Soldering. ・ IC105 終了 END 24 N.G (1) [X101]を確認 (2) 半田付けを確認 ・ [IC109] O.K. 半田付けを確認 ・ R202 S-102 1.2. ディスク読めず [No Play], [00 00] 等の表示 1.2. No Sound,Noise generated [No Play], [00 00] displayed etc. (1) ディスク回転せず (1) CD,DVD PLAY Check the Emission of Pick-up. IU-3807(FEP UNIT) ・ Emission of P.U. laser O.K.? ・ The test mode "T2" is executed. Laser current O.K.? N.G (1) Check Soldering of P.U. ・ short-circuit? (2) Check the circumference soldering of TR603 and TR604. (3) Check connector insertion. ・ [P.U.]-[IU-3807] FFC(CX241) (4) Check the soldering [IC601] and circumference soldering of [IC601] (5) Check the soldering [IC101] ,[IC102]and circumference soldering of [IC101] ,[IC102] Pick-upの発光を確認 IU-3807(FEP UNIT) ・ P.U. レーザー発光 O.K.? ・ テストモード T2 実行 レーザー電流 OK? P.U. の半田ショートランドを確認 TR603, TR604周辺の半田付けを確認 コネクタ接続を確認 [P.U.]-[IU-3807] FFC(CX241) [IC601]とその周辺の半田付けを確認 [IC101],[IC102]とその周辺の半田付けを確認 O.K. O.K. Check Spindle drive. IU-3807(FEP UNIT) ・ [SPDRV]: "H" level? N.G (1) (2) (3) ・ (4) (5) N.G (1) Check soldering of [IC101]:56, 75pin (2) Check the circumference soldering of [SPDRV], [FG] signal. (3) Check the soldering [IC151] and circumference soldering of [IC151] スピンドルドライブ信号の確認 IU-3807(FEP UNIT) ・ [SPDRV]: "H" level? N.G (1) [IC101] 56, 75pinの半田付けを確認 (2) [SPDRV] [FG]信号ライン周辺の半田付けを確認 (3) [IC151]とその周辺の半田付けを確認 N.G 半田付けを確認 IU-3807-1(FEP UNIT) ・ [IC101],[IC601]とその周辺の半田付けを確認 O.K. O.K. 終了 END (2) CD or DVD チェック工程 (2) CD or DVD check process Check the RF signal. IU-3807(FEP UNIT) ・ Check the voltage of Test-Point (TP) ・ TP[mAMON1] [AMON2]: differential output about1.0Vp-p N.G RF信号の確認 IU-3807(FEP UNIT) ・ テストポイント (TP) の電圧確認 ・ TP [AMON1] [AMON2]: 差動出力 約1.0Vp-p Check Soldering. 㪠㪬㪄㪊㪏㪇㪎㩿㪝㪜㪧㩷㪬㪥㪠㪫㪀 ・ Check the circumference soldering of [IC101], [IC601] O.K. O.K. 終了 END 25 S-102 1.3. 音声出力せず、ノイズ発生 1.3. No Sound,Noise generated (1) CD,DVD 再生時 (1) CD,DVD PLAY Check Power Supply Voltages. 1U-3836(MAIN UNIT) ・ +12V_A1,-12V_A1 ・ +7V,-7V of [IC601] ・ +1.2V_DSP of [IC401] N.G 電源電圧確認 1U-3836(MAIN UNIT) ・ +12V_A1,-12V_A1 ・ +7V,-7V of [IC601] ・ +1.2V_DSP of [IC401] Check Soldering. ・ IC602,IC603 ・ IC404 N.G RESET信号の確認 [IC401].[IC501],[IC502] 1U-3836(MAIN UNIT) ・ [IC401]:[DSP_RST]202pin ・ [IC501]:[CODEC_RST]10 pin. ・ [IC502]:[DIR_RST]41 pin. "H"level O.K.? Check Soldering. ・ [IC301]:115,82,109 pin ・ IC401,RR210 ・ IC501,R603 ・ IC502,R661 N.G B/EからDIRへのデジタルオーディオ データ出力確認 1U-3836(MAIN UNIT) ・ [IC101]出力/[IC502]入力: [BE_SPDIF] Check Soldering. ・ [IC101]:41pin ・ R119 ・ [IC502]:2pin ・ R685 N.G DIRからPLDへのデジタルオーディオ データ出力確認 1U-3836(MAIN UNIT) ・ [IC502]出力/ [IC503]入力: [DIR_S_64FS],[DIR_S_FS], [DIR_DA] Check Soldering. ・ [IC502]:22,23,21pin ・ R670-672 ・ [IC503]:71,72,70pin ・ R737-739 N.G PLDからDSPへのデジタル オーディオデータ出力確認 1U-3836(MAIN UNIT) ・ [IC503]出力/ [IC401]入力: [DSPI_64FS],[DSPI_FS], [DSPI_FDA] Check Soldering. ・ [IC503]:60,59,55pin ・ R719,722,723 ・ [IC401]:146,144,125pin ・ RR165,167 N.G DSPからPLD/CODECへのデジタル オーディオデータ出力確認 1U-3836(MAIN UNIT) ・ [IC401]出力/[IC503]入力: [DSPO_64FS],[DSPO_FS] ・ [IC401]出力/[IC501]入力: [DSPO_FDA],[DSPO_CWDA] Check Soldering. ・ [IC401]:137,143,133,135pin ・ RR169,168,173,171 ・ [IC503]:64,61pin ・ R725,724 ・ [IC501]:16,15pin ・ R656,655 N.G 半田付けを確認 ・ [IC502]:22,23,21pin ・ R670-672 ・ [IC503]:71,72,70pin ・ R737-739 N.G 半田付けを確認 ・ [IC503]:60,59,55pin ・ R719,722,723 ・ [IC401]:146,144,125pin ・ RR165,167 N.G 半田付けを確認 ・ [IC401]:137,143,133,135pin ・ RR169,168,173,171 ・ [IC503]:64,61pin ・ R725,724 ・ [IC501]:16,15pin ・ R656,655 O.K. O.K. Check Digital Audio Data output from PLD to CODEC 1U-3836(MAIN UNIT) ・ [IC503]output and [IC501]input: [DSC_64FS],[DAC_FS], 半田付けを確認 ・ [IC101]:41pin ・ R119 ・ [IC502]:2pin ・ R685 O.K. O.K. Check Digital Audio Data output from DSP to PLD/CODEC 1U-3836(MAIN UNIT) ・ [IC401]output and [IC503]input: [DSPO_64FS],[DSPO_FS] ・ [IC401]output and [IC501]input: [DSPO_FDA],[DSPO_CWDA] N.G O.K. O.K. Check Digital Audio Data output from PLD to DSP 1U-3836(MAIN UNIT) ・ [IC503]output and [IC401]input: [DSPI_64FS],[DSPI_FS], [DSPI_FDA] 半田付けを確認 ・ [IC301]:115,82,109 pin ・ IC401,RR210 ・ IC501,R603 ・ IC502,R661 O.K. O.K. Check Digital Audio Data output from DIR to PLD 1U-3836(MAIN UNIT) ・ [IC502]output and [IC503]input: [DIR_S_64FS],[DIR_S_FS], [DIR_DA] N.G O.K. O.K. Check Digital Audio Data output from B/E to DIR 1U-3836(MAIN UNIT) ・ [IC101]output and [IC502]input: [BE_SPDIF] 半田付けを確認 ・ IC602,IC603 ・ IC404 O.K. O.K. Check Reset signal of [IC401], [IC501],[IC502]. 1U-3836(MAIN UNIT) ・ [IC401]:[DSP_RST]202pin ・ [IC501]:[CODEC_RST]10 pin. ・ [IC502]:[DIR_RST]41 pin. "H"level O.K.? N.G N.G PLDからCODECへのデジタル オーディオデータ出力確認 1U-3836(MAIN UNIT) ・ [IC503]出力/[IC501]入力: [DSC_64FS],[DAC_FS], Check Soldering. ・ [IC503]:79,80pin ・ R728,727 ・ [IC501]:17,18pin ・ R657,658 O.K. O.K. 26 N.G 半田付けを確認 ・ [IC503]:79,80pin ・ R728,727 ・ [IC501]:17,18pin ・ R657,658 S-102 Check Analog Audio Data output from CODEC to AMP. 1U-3836(MAIN UNIT) ・ [IC501]output and [IC506],[IC507] [FL],[FR],[SW] N.G CODECからAMPへのアナログ オーディオデータ出力確認 1U-3836(MAIN UNIT) ・ [IC501]出力/[IC506],[IC507]入力: [FL],[FR],[SW] Check Soldering. ・ [IC501]:28,29,31pin ・ [IC506],[IC507] N.G オーディオミュート信号の確認 1U-3836(MAIN UNIT) ・ [DAC_MUTE] "L"level O.K.? Check Soldering. ・ [IC503]:86pin ・ TR501-505 N.G AMPからFUNC.VR.へのアナログ オーディオデータ出力確認 1U-3836(MAIN UNIT) ・ AMP出力/ [IC601]入力: [DSP_FL],[DSP_FR],[DSP_LFE] Check Soldering. ・ [IC601]:11,12,8pin N.G FUNC.VR.から差動AMPへのアナログ オーディオデータ出力確認 1U-3836(MAIN UNIT) ・ [IC601]出力/差動AMP入力: [IC601]:54,47,35pin Check Soldering. ・ [IC601]:54,47,35pin ・ IC609,610 N.G オーディオミュート信号の確認 1U-3836(MAIN UNIT) ・ [PRE_MUTE_MAIN], [PRE_MUTE_SUB] "L"level O.K.? Check Soldering. ・ [IC301]:100,83pin ・ TR609-615 半田付けを確認 ・ [IC601]:11,12,8pin N.G 半田付けを確認 ・ [IC601]:54,47,35pin ・ IC609,610 N.G 半田付けを確認 ・ [IC301]:100,83pin ・ TR609-615 O.K. O.K. Check Analog Audio Data output from Diff.AMP. 1U-3836(MAIN UNIT) ・ [IC609],[IC610]output: [FL+],[FL-],[FR+],[FR-], [SW+],[SW-] N.G O.K. O.K. Check audio mute signal. 1U-3836(MAIN UNIT) ・ [PRE_MUTE_MAIN], [PRE_MUTE_SUB] "L"level O.K.? 半田付けを確認 ・ [IC503]:86pin ・ TR501-505 O.K. O.K. Check Analog Audio Data output from FUNC.VR. to Diff.AMP. 1U-3836(MAIN UNIT) ・ [IC601]output and Diff.AMP.input: [IC601]:54,47,35pin N.G O.K. O.K. Check Analog Audio Data output from AMP to FUNC.VR. 1U-3836(MAIN UNIT) ・ AMPoutput and [IC601]input: [DSP_FL],[DSP_FR],[DSP_LFE] 半田付けを確認 ・ [IC501]:28,29,31pin ・ [IC506],[IC507] O.K. O.K. Check audio mute signal. 1U-3836(MAIN UNIT) ・ [DAC_MUTE] "L"level O.K.? N.G N.G 差動AMPのアナログオーディオ データ出力確認 1U-3836(MAIN UNIT) ・ [IC609],[IC610]出力: [FL+],[FL-],[FR+],[FR-], [SW+],[SW-] Check Soldering. ・ IC609,610 ・ CX171 O.K. O.K. 終了 END 27 N.G 半田付けを確認 ・ IC609,610 ・ CX171 S-102 (2) アナログオーディオ入力時(AUX1,AUX2) AUX1-2からFUNC.VR.へのアナログ (2) Analog audio in(AUX1,AUX2) Check Analog Audio Data input from AUX1-2 to FUNC.VR. Check Analog Audio Data input 1U-3836(MAIN UNIT) from AUX1-2 to FUNC.VR. ・ [AUX1-2 IN]-L/R 1U-3836(MAIN UNIT) ・ [AUX1-2 IN]-L/R N.G N.G オーディオデータ入力確認 Check Soldering. ・ JK601 Check Soldering. ・ [IC601]74-77pin AUX1-2からFUNC.VR.へのアナログ 1U-3836(MAIN UNIT) オーディオデータ入力確認 ・ [AUX1-2 IN]-L/R 1U-3836(MAIN UNIT) ・ [AUX1-2 IN]-L/R ・ JK601 ・ [IC601]74-77pin O.K. N.G O.K. 半田付けを確認 ・ JK601 半田付けを確認 ・ [IC601]74-77pin ・ JK601 ・ [IC601]74-77pin O.K. O.K. Check Analog Audio Data input from FUNC.VR. to Data AMPinput Check Analog Audio 1U-3836(MAIN from FUNC.VR. toUNIT) AMP ・ [IC601]output 1U-3836(MAIN UNIT)and [IC504] /[IC505]input: ・ [IC601]output and [IC504] [A/D_L],[A/D_R] /[IC505]input: N.G N.G N.G FUNC.VR.からAMPへのアナログ オーディ オデータ入力確認 FUNC.VR.からAMPへのアナログ 1U-3836(MAIN UNIT) オーディオデ ータ入力確認 N.G ・ [IC601] 1U-3836(MAIN UNIT) 出力/[IC504],[IC505]入力 [A/D_L],[A/D_R] /[IC504],[IC505]入力 ・ [IC601]出力 Check Soldering. [IC601]14,17pin Check・Soldering. ・ IC504,505 ・ [IC601]14,17pin ・ IC504,505 N.G 半田付けを確認 ・ [IC601]14,17pin 半田付けを確認 ・ IC504,505 ・ [IC601]14,17pin ・ IC504,505 [A/D_L],[A/D_R] [A/D_L],[A/D_R] O.K. O.K. O.K. O.K. Check Analog Audio Data input AMPからCODECへのアナログ オーディオデータ入力確認 オーディオデ ータ入力確認 N.G 1U-3836(MAIN UNIT) 1U-3836(MAIN UNIT) ・ [IC504/505]出力/[IC501]入力 ・ [IC504/505]出力/[IC501]入力 Check・Soldering. IC504,505 ・ IC504,505 ・ [IC501]39-42pin ・ [IC501]39-42pin O.K. O.K. O.K. 半田付けを確認 N.G ・ IC504,505 ・ IC504,505・ [IC501]39-42pin ・ [IC501]39-42pin O.K. CODECからDIRへのデジタル Check Digital Audio Data output Check Digital Audio Data output from CODEC to DIR from CODEC to DIR 1U-3836(MAIN UNIT) 1U-3836(MAIN UNIT) ・ [IC501]output and [IC502]input: ・ [IC501]output and [IC502]input: [AD_FDA] [AD_FDA] 半田付けを確認 AMPからCODECへのアナログ Check Soldering. Check Analog Data input from AMP to Audio CODEC N.G from AMP to CODEC N.G 1U-3836(MAIN UNIT) 1U-3836(MAIN UNIT) ・ [IC504/505]output and [IC501]input: ・ [IC504/505]output and [IC501]input: N.G N.G CODECからDIRへのデジタル オーディオデータ出力確認 オーディオデータ出力確認 N.G 1U-3836(MAIN UNIT) 1U-3836(MAIN UNIT) 出力/力: [IC502]入力: [IC501] 出力 / [IC502]入 ・ [IC501]・ [AD_FDA][AD_FDA] Check Soldering. Check Soldering. ・ [IC501]:20pin ・ [IC501]:20pin ・ [IC502]:24pin ・ [IC502]:24pin O.K. O.K. O.K. END END 終了 N.G 半田付けを確認 半田付けを確認 ・ [IC501]:20pin ・ [IC501]:20pin ・ ・ [IC502]:24pin[IC502]:24pin O.K. 終了 (3) デジタルオーディオ入力時 (3) デジタルオーディオ入力時 (3) (3)Digital Digitalaudio audioinin Check Audio Data input CheckDigital Digital Audio Data input from to to DIR fromDig-IN Dig-IN DIR 1U-3836(MAIN UNIT) 1U-3836(MAIN UNIT) ・・[DIN] [DIN] N.GN.G Dig-INからDIRへのデジタル Dig-INからDIRへのデジタル オーディオデ ータ入 力確ータ入 認 オーディ オデ 力確認 1U-3836(MAIN UNIT) 1U-3836(MAIN UNIT) ・ [DIN] ・ [DIN] Check Soldering. Check Soldering. ・ IC511 ・ IC511 ・ [IC502]9pin ・ [IC502]9pin O.K. O.K. O.K. 終了 END END 28 終了 N.G O.K. 半田付けを確認 N.G 半田付けを確認 ・ IC511 ・ IC511 ・ [IC502]9pin ・ [IC502]9pin S-102 3. 1U-3836-1 (MAIN UNIT) 3. 1U-3836-1 (MAIN UNIT) 3-1.DVD 再生時 3-1.DVD 再生時 3. 3. 1U-3836-1 1U-3836-1(MAIN (MAINUNIT) UNIT) 3-1.DVD PLAY 3-1.DVD PLAY (1) インターレース映像出力せず (1) INTERLACE output does not outputed. (1) インターレース映像出力せず (1) INTERLACE output does not outputed. Check Power Supply Voltages. Check Power Supply Voltages. 1U-3836-1(MAIN UNIT) 1U-3836-1(MAIN UNIT) ・ +3.3V_D1,±5V_V1 N.G N.G 電源電圧確認 電源電圧確認 1U-3836-1(MAIN UNIT) 1U-3836-1(MAIN UNIT) ・ +3.3V_D1,±5V_V1 Check Soldering. Check Soldering. ・ IC304 ・ IC304 ・ +3.3V_D1,±5V_V1 O.K. O.K. N.G N.G ・ IC806,807 クロックの波形確認 1U-3836-1(MAIN UNIT) クロックの波形確認 ・ [IC701]192pin 1U-3836-1(MAIN UNIT) 13.5MHz OK? ・ [IC701]192pin Check Soldering. N.G ・ X701 Check Soldering. ・ X701 13.5MHz OK? O.K. O.K. N.G ・ [IC301]12pin,RR701 ・ [IC301]50pin,RR355 N.G N.G Check Digital Video DATA output 1U-3836-1(MAIN UNIT) ・ [IC101]output/[IC801]input O.K. [BE_ID0-7.],[BE_HS],[BE_VS],[PXCLK] N.G Check Soldering. ・ IC802 N.G ・ ・ ・ 半田付けを確認 ・ X701 半田付けを確認 N.G ・ X701 O.K. N.G 半田付けを確認 ・ [IC301]57pin,RR838 半田付けを確認 ・ [IC301]12pin,RR701 N.G ・ [IC301]57pin,RR838 ・ [IC301]50pin,RR355 ・ [IC301]12pin,RR701 ・ [IC301]50pin,RR355 ビデオミュート信号の確認 O.K. 1U-3836-1(MAIN UNIT) ・ [IC802]:[S/V_MUTE],[COMP_MUTE] ビデオミュート信号の確認 "H"level O.K.? 1U-3836-1(MAIN UNIT) N.G 半田付けを確認 ・ IC802 N.G ・ [IC802]:[S/V_MUTE],[COMP_MUTE] "H"level O.K.?O.K. B/EからENCODERへのデジタル映像データ出力 O.K. の確認 1U-3836-1(MAIN UNIT) N.G B/EからENCODERへのデジタル映像データ出力 ・ [IC101]出力/[IC801]入力 の確認 [BE_ID0-7.],[BE_HS],[BE_VS],[PXCLK] Check Soldering. O.K. N.G ・ [IC801]:[ENC_RST] "H"level O.K.?O.K. Check Soldering. ・ IC802 ・ [IC802]:[S/V_MUTE],[COMP_MUTE] O.K. "H"level O.K.? 1U-3836-1(MAIN UNIT) Check Digital Video DATA output ・ [IC101]output/[IC801]input from B/E to ENCODER [BE_ID0-7.],[BE_HS],[BE_VS],[PXCLK] ・ IC806,807 O.K. RESET信号の確認 1U-3836-1(MAIN UNIT) RESET信号の確認 ・ [IC703]:[VPLD_RST] 1U-3836-1(MAIN UNIT) ・ [IC701]:[FLI_RST] ・ [IC703]:[VPLD_RST] ・ [IC801]:[ENC_RST] ・ O.K.? [IC701]:[FLI_RST] "H"level Check Soldering. ・ [IC301]57pin,RR838 Check Soldering. ・ [IC301]12pin,RR701 N.G ・ [IC301]50pin,RR355 ・ [IC301]57pin,RR838 ・ [IC801]:[ENC_RST] "H"level O.K.? O.K. from B/E to ENCODER 半田付けを確認 N.G 半田付けを確認 ・ IC706,707 ・ IC806,807・ IC706,707 O.K. N.G Check video mute signal. O.K. 1U-3836-1(MAIN UNIT) ・ [IC802]:[S/V_MUTE],[COMP_MUTE] Check video mute signal. "H"level O.K.? UNIT) 1U-3836-1(MAIN N.G O.K. O.K. Check Reset signal. 1U-3836-1(MAIN UNIT) Check Reset signal. ・ [IC703]:[VPLD_RST] 1U-3836-1(MAIN UNIT) ・ [IC701]:[FLI_RST] ・ [IC703]:[VPLD_RST] ・ [IC801]:[ENC_RST] ・"H"level [IC701]:[FLI_RST] O.K.? O.K. ・ [IC801]:+2.5V_DE,+2.5V_A O.K. 13.5MHz OK? ・ IC304 電源電圧確認 電源電圧確認 1U-3836-1(MAIN UNIT) 1U-3836-1(MAIN UNIT) ・ [IC701]:+1.8V ・ [IC701]:+1.8V ・ [IC801]:+2.5V_DE,+2.5V_A Check Soldering. Check Soldering. ・ IC706,707 ・ IC706,707 ・ IC806,807 ・ [IC801]:+2.5V_DE,+2.5V_A Check Clock waveform. 1U-3836-1(MAIN UNIT) Check Clock waveform. ・ [IC701]192pin 1U-3836-1(MAIN UNIT) OK? ・13.5MHz [IC701]192pin 半田付けを確認 N.G 半田付けを確認 ・ IC304 ・ +3.3V_D1,±5V_V1 O.K. Check Power Supply Voltages. Check Power Supply 1U-3836-1(MAIN UNIT) Voltages. 1U-3836-1(MAIN ・ [IC701]:+1.8V UNIT) [IC701]:+1.8V ・・[IC801]:+2.5V_DE,+2.5V_A N.G [IC101]:106-110,113-115,118,119pin Check Soldering. IC109,IC803 RR326-349 ・ [IC101]:106-110,113-115,118,119pin ・ IC109,IC803 ・ RR326-349 1U-3836-1(MAIN UNIT) 力 ・ [IC101]出力/[IC801]入 O.K. [BE_ID0-7.],[BE_HS],[BE_VS],[PXCLK] O.K. O.K. 29 半田付けを確認 ・ IC802 半田付けを確認 ・ [IC101]:106-110,113-115,118,119pin 半田付けを確認 ・ IC109,IC803 ・ RR326-349 N.G ・ [IC101]:106-110,113-115,118,119pin ・ IC109,IC803 ・ RR326-349 S-102 Check analog signal for Video from ENCODER to Video driver(COMPONENT) 1U-3836-1(MAIN UNIT) ・ [IC801]output and [IC802]input: [Py],[Pb],[Pr] N.G Check Soldering. ・ [IC801]37-39pin ・ VR803-805 ・ TR803-805 ・ [IC802]11,13,15pin ENCODERからビデオドライバーへのアナログ 映像データ出力の確認(COMPONENT) 1U-3836-1(MAIN UNIT) ・ [IC801]出力/[IC802]入力: [Py],[Pb],[Pr] O.K. Check analog signal for Video from ENCODER to Video selector(CVBS/YC) 1U-3836-1(MAIN UNIT) ・ [IC801]output and [IC804]input: [Y],[C] N.G 半田付けを確認 ・ [IC801]43,42pin ・ VR801,802 ・ TR801,802 ・ [IC804]1,12pin N.G 半田付けを確認 ・ [IC804]3,13pin ・ [IC802]8,4pin O.K. N.G Check Soldering. ・ [IC801]43,42pin ・ VR801,802 ・ IC801,802 ・ [IC804]1,12pin ENCODERからビデオセレクタへのアナログ 映像データ出力の確認(CVBS/YC) 1U-3836-1(MAIN UNIT) ・ [IC801]出力/[IC804]入力: [Y],[C] O.K. Check analog signal for Video from selector to Video driver(CVBS/YC) 1U-3836-1(MAIN UNIT) ・ [IC804]output and [IC802]input: N.G 半田付けを確認 ・ [IC801]37-39pin ・ VR803-805 ・ TR803-805 ・ [IC802]11,13,15pin O.K. N.G Check Soldering. ・ [IC804]3,13pin ・ [IC802]8,4pin ビデオセレクタからビデオドライバーへのアナログ 映像データ出力の確認(CVBS/YC) 1U-3836-1(MAIN UNIT) ・ [IC804]出力/[IC802]入力: O.K. O.K. END 終了 30 S-102 ( ) p p (2) プログレッシブ映像出力せず (2) PROGRESSIVE output does not outputed. Check Digital signal for Video from B/E to signal I/P for Video Check Digital 1U-3836-1(MAIN UNIT) from B/E to I/P ・ [IC101]output and [IC701]input: 1U-3836-1(MAIN UNIT) [B/E_ID0-7],[BE_HS],[BE_VS],[PXCLK] ・ [IC101]output and [IC701]input: B/EからI/Pへのデジタル映像データ出力 の確認 B/EからI/Pへのデジタル映像データ出力 1U-3836-1(MAIN UNIT) の確認 出力/[IC701]入力: ・ [IC101] 1U-3836-1(MAIN UNIT) [B/E_ID0-7],[BE_HS],[BE_VS],[PXCLK] /[IC701]入力: ・ [IC101]出力 Check Soldering. N.G Check・ [IC101]106-119pin Soldering. ・ RR743-765 N.G ・ [IC101]106-119pin ・ RR743-765 O.K. O.K. O.K. O.K. I/PからFPGAへのデジタル映像データ出力 Check Digital signal for Video I/PからFPGAへのデジタル映像データ出力 の確認 の確認 1U-3836-1(MAIN UNIT) 1U-3836-1(MAIN UNIT) N.G 出力/[IC703]入力: ・ [IC701] / [IC703]入 力: ・ [IC701]出力 [IP_R6/Y0-9],[IP_BO/C0-9],[IP_HS],[IP_VS], [IP_R6/Y0-9],[IP_BO/C0-9],[IP_HS],[IP_VS], [IP_DE],[IP_PXCLK] [IP_DE],[IP_PXCLK] Check Soldering. Soldering. N.G Check・ [IC701]118-156pin N.G ・ [IC701]118-156pin ・ RR803-830 ・ RR803-830 O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K. 終了 END END 31 終了 半田付けを確認 半田付けを確認 ・ [IC703]105-138pin ・N.G [IC703]105-138pin ・ RR308-349・ RR308-349 O.K. ENCODERからビデオドライバーへのアナログ ENCODERからビデオドライバーへのアナログ 映像データ 出力の確認出力の確認 映像データ 1U-3836-1(MAIN UNIT) N.G 1U-3836-1(MAIN UNIT) 出力 /[IC802]入 ・ [IC801]・ 出力力: /[IC802]入力: [IC801] [Py],[Pb],[Pr] [Py],[Pb],[Pr] Check Soldering. Check Soldering. ・ [IC801]37-39pin ・ [IC801]37-39pin N.G N.G ・ VR803-805 ・ VR803-805 ・ TR803-805 ・ TR803-805 ・ [IC802]11,13,15pin ・ [IC802]11,13,15pin 半田付けを確認 半田付けを確認 N.G ・ [IC701]118-156pin ・ [IC701]118-156pin ・ RR803-830 ・ RR803-830 O.K. FPGAからENCODERへのデジタル映像データ出力 FPGAからENCODERへのデジタル映像データ出力 の確認 の確認 1U-3836-1(MAIN UNIT) 1U-3836-1(MAIN UNIT) N.G 出力力: /[IC801]入力: [IC703] 出力 /[IC801]入 ・ [IC703]・ [ENC_Y0-9],[ENC_C0-9],[ENC_HS],[ENC_VS], [ENC_Y0-9],[ENC_C0-9],[ENC_HS],[ENC_VS], [ENC_DE],[ENC_CLK] [ENC_DE],[ENC_CLK] Check Digital signal Video Check Digital signal forfor Video from FPGA to ENCODER Check Soldering. from FPGA to ENCODER Check Soldering. 1U-3836-1(MAIN UNIT) ・ [IC703]105-138pin 1U-3836-1(MAIN UNIT) N.G N.G ・ [IC703]105-138pin [IC703]output and [IC801]input: ・ RR308-349 ・・[IC703]output and [IC801]input: ・ RR308-349 [ENC_Y0-9],[ENC_C0-9],[ENC_HS],[ENC_VS], [ENC_Y0-9],[ENC_C0-9],[ENC_HS],[ENC_VS], [ENC_DE],[ENC_CLK] [ENC_DE],[ENC_CLK] Check analog signal forfor Video Check analog signal Video from to to Video driver fromENCODER ENCODER Video driver 1U-3836-1(MAIN UNIT) 1U-3836-1(MAIN UNIT) ・・[IC801]output and [IC802]input: [IC801]output and [IC802]input: [Py],[Pb],[Pr] [Py],[Pb],[Pr] ・ RR743-765 [B/E_ID0-7],[BE_HS],[BE_VS],[PXCLK] [B/E_ID0-7],[BE_HS],[BE_VS],[PXCLK] Check Digital signal for Video from I/P to FPGA from I/P to FPGA UNIT) 1U-3836-1(MAIN 1U-3836-1(MAIN UNIT) ・ [IC701]output and [IC703]input: ・ [IC701]output and [IC703]input: [IP_R6/Y0-9],[IP_BO/C0-9],[IP_HS],[IP_VS], [IP_R6/Y0-9],[IP_BO/C0-9],[IP_HS],[IP_VS], [IP_DE],[IP_PXCLK] [IP_DE],[IP_PXCLK] N.G 半田付けを確認 N.G ・ [IC101]106-119pin 半田付けを確認 ・ RR743-765 ・ [IC101]106-119pin O.K. 半田付けを確認 半田付けを確認 ・ [IC801]37-39pin ・ [IC801]37-39pin ・N.G VR803-805・ VR803-805 ・ TR803-805・ TR803-805 ・ [IC802]11,13,15pin ・ [IC802]11,13,15pin S-102 (3) HDMI映像出力せず (3) HDMI映像出力せず (3)HDMI HDMIoutput outputdoes does outputed. (3) notnot outputed. Check Power Supply Voltages. Check Power Supply Voltages. 1U-3836-1(MAIN UNIT) 1U-3836-1(MAIN UNIT) ・・[IC704]:+1.8V [IC704]:+1.8V 電源電圧確認 電源電圧確認 1U-3836-1(MAIN UNIT) 1U-3836-1(MAIN UNIT) ・ [IC704]:+1.8V ・ [IC704]:+1.8V N.G N.G Check Soldering. Check Soldering. ・ IC708 ・ IC708 O.K. O.K. O.K. Check Reset signal. Check Reset signal. 1U-3836-1(MAIN UNIT) 1U-3836-1(MAIN UNIT) ・ [IC704]:[HDMI_RST] ・ [IC704]:[HDMI_RST] "H"level O.K.? N.G ・ RR853 "H"level O.K.? O.K. O.K. N.G Check Soldering. Check Soldering. ・ RR856-886 N.G ・ [IC704]49-80,1,2pin ・ RR856-886 ・ [IC704]49-80,1,2pin END O.K. 半田付けを確認 半田付けを確認 ・ RR856-886 N.G ・ RR856-886 ・ [IC704]49-80,1,2pin ・ [IC704]49-80,1,2pin O.K. O.K. O.K. O.K. ・ RR853 [HDMTVS],[HDMTDE],[HDMTCLK] O.K. ・ [IC704]output 半田付けを確認 半田付けを確認 N.G ・ [IC105]15pin ・ [IC105]15pin ・ RR853 FPGAからTRANSMITTERへのデジタル映像 FPGAからTRANSMITTERへのデジタル映像 データ出力の確認 データ出力の確認 1U-3836-1(MAIN UNIT) N.G 1U-3836-1(MAIN 出力/[IC704]入力:UNIT) ・ [IC703] ・ [IC703]出力/[IC704]入力: [HDMTY0-9],[HDMTC0-9],[HDMTHS], [HDMTY0-9],[HDMTC0-9],[HDMTHS], [HDMTVS],[HDMTDE],[HDMTCLK] [HDMTVS],[HDMTDE],[HDMTCLK] Check Digital signal for Video from TRANSMITTER HDMI_CON. Check Digital signaltofor Video 1U-3836-1(MAIN UNIT) to HDMI_CON. from TRANSMITTER ・ [IC704]output UNIT) 1U-3836-1(MAIN N.G "H"level O.K.? O.K. Check Digital signal for Video Check Digital signal for Video from FPGA to TRANSMITTER from FPGA to TRANSMITTER 1U-3836-1(MAIN UNIT) 1U-3836-1(MAIN UNIT) ・ [IC703]output and [IC704]input: ・[HDMTY0-9],[HDMTC0-9],[HDMTHS], [IC703]output and [IC704]input: [HDMTY0-9],[HDMTC0-9],[HDMTHS], [HDMTVS],[HDMTDE],[HDMTCLK] 半田付けを確認 半田付けを確認 N.G ・ IC708 ・ IC708 O.K. RESET信号の確認 RESET信号の確認 1U-3836-1(MAIN UNIT) 1U-3836-1(MAIN UNIT) ・ [IC704]:[HDMI_RST] ・ [IC704]:[HDMI_RST] "H"level O.K.? Check Soldering. N.G Check Soldering. ・ [IC105]15pin ・ [IC105]15pin ・ RR853 N.G TRANSMITTERからHDMIコネクタへのデジタル 映像データ 出力の確認 N.G TRANSMITTERからHDMIコネクタへのデジタル 1U-3836-1(MAIN UNIT) 映像データ 出力の確認 ・ [IC704]出力 1U-3836-1(MAIN UNIT) Check Soldering. N.G ・ [IC704]26-36pin Check Soldering. N.G ・ TR701 ・ [IC704]26-36pin ・ JK701 ・ TR701 ・ JK701 ・ [IC704]出力 O.K. 終了 END 32 ・ JK701 O.K. 終了 O.K. 半田付けを確認 ・ [IC704]26-36pin 半田付けを確認 TR701 ・N.G ・ [IC704]26-36pin ・ JK701 ・ TR701 S-102 3-2.外部入力時 3-2.AUX IN (1) Conposite INPUT (1) コンポジット入力 Check Power Supply Voltages. 1U-3836-1(MAIN UNIT) ・ ±5V_V1 N.G Check Soldering. ・ CX142 電源電圧確認 1U-3836-1(MAIN UNIT) ・ ±5V_V1 O.K. Check analog signal for Video from connector to Video selector 1U-3836-1(MAIN UNIT) ・ [IC805]input: [CVBS1],[CVBS2] N.G Check Soldering. ・ JK301 ・ RR411,413 ・ [IC805]1,5pin コネクタからビデオセレクタへのアナログ 映像出力の確認 1U-3836-1(MAIN UNIT) ・ [IC805]入力: [CVBS1],[CVBS2] N.G 半田付けを確認 ・ JK301 ・ RR411,413 ・ [IC805]1,5pin O.K. N.G Check Soldering. ・ [IC805]3pin ・ CC145 ・ [IC802]5pin ビデオセレクタからビデオドライバーへの アナログ映像出力の確認 1U-3836-1(MAIN UNIT) ・ [IC805]出力/[IC802]入力: [SEL_CVBS] O.K. Check analog signal for Video from Video driver to connector 1U-3836-1(MAIN UNIT) ・ [IC802]output 半田付けを確認 ・ CX142 O.K. O.K. Check analog signal for Video from Video selector to Video driver 1U-3836-1(MAIN UNIT) ・ [IC805]output/[IC802]input: [SEL_CVBS] N.G N.G 半田付けを確認 ・ [IC805]3pin ・ CC145 ・ [IC802]5pin O.K. N.G Check Soldering. ・ [IC802]30pin ・ CC161 ・ RR420 ・ JK801 ビデオドライバーからコネクタへのアナログ 映像出力の確認 1U-3836-1(MAIN UNIT) ・ [IC802]出力 O.K. O.K. END 終了 33 N.G 半田付けを確認 ・ [IC802]30pin ・ CC161 ・ RR420 ・ JK801 S-102 (2) S端子入力 (2) Y/C INPUT Check Power Supply Voltages. 1U-3836-1(MAIN UNIT) ・ ±5V_V1 N.G 電源電圧確認 1U-3836-1(MAIN UNIT) ・ ±5V_V1 Check Soldering. ・ CX142 N.G コネクタからビデオセレクタへのアナログ 映像出力の確認 1U-3836-1(MAIN UNIT) ・ [IC804]入力: [Y1],[Y2],[C1],[C2] Check Soldering. ・ JK301 ・ RR402,403,408,409 ・ [IC804]2,5,14,15pin N.G ビデオセレクタからビデオドライバーへの アナログ映像出力の確認 1U-3836-1(MAIN UNIT) ・ [IC804]出力/[IC802]入力: [SELY],[SELC] Check Soldering. ・ [IC804]3,13pin ・ CC145,147 ・ [IC802]4,8pin 半田付けを確認 ・ JK301 ・ RR402,403,408,409 ・ [IC804]2,5,14,15pin N.G 半田付けを確認 ・ [IC804]3,13pin ・ CC145,147 ・ [IC802]4,8pin O.K. O.K. Check analog signal for Video from Video driver to connector 1U-3836-1(MAIN UNIT) ・ [IC802]output N.G O.K. O.K. Check analog signal for Video from Video selector to Video driver 1U-3836-1(MAIN UNIT) ・ [IC804]output/[IC802]input: [SELY],[SELC] 半田付けを確認 ・ CX142 O.K. O.K. Check analog signal for Video from connector to Video selector 1U-3836-1(MAIN UNIT) ・ [IC804]input: [Y1],[Y2],[C1],[C2] N.G ビデオドライバーからコネクタへのアナログ 映像出力の確認 1U-3836-1(MAIN UNIT) ・ [IC802]出力 Check Soldering. N.G ・ [IC802]27,32pin ・ CC160,163 ・ JK801 O.K. O.K. 終了 END 34 半田付けを確認 N.G ・ [IC802]27,32pin ・ CC160,163 ・ JK801 S-102 ● DSW-S102 1. 1U-3811 (D.AMP/SMPS UNIT) ● DSW-S102 1. 1U-3811 (D.AMP/SMPS UNIT) (1) AMPLIFER (1) アンプ Check Reset signal. (IC208 4pin) "H" level (About 3.3V) N.G. Check the following parts (and surrounding area) and their soldering. • [IC208] (BD4730) • [IC201] circumference of 9pin(TAS5066PAGRG4) Also circuits connected to this part リセット信号の確認 ・ (IC208 4pin) "H" レベル ( 約 3.3V) N.G. Check the following parts (and surrounding area) and their soldering. • [X201] (X-TAL) • [IC202] (SN74HCU04APWR) • [IC201] circumference of 2pin(TAS5066PAGRG4) • [IC203] circumference of 15pin(PCM1803DBR) • [IC204] circumference of 15pin(PCM1803DBR) Also circuits connected to this part クロック波形の確認? ・ (IC201 2pin) ・ (IC203 15pin) ・ (IC204 15pin) ( 波形 1」を参照 N.G. PWM 信号波形の確認 ・ (IC206 4,5,6pin) ・ (IC206 14,15,16pin) ・ (IC207 2,4,17pin) 「波形2」を参照 Check the following parts (and surrounding area) and their soldering. • [IC201] ALL pin (TAS5066PAGRG4) Also circuits connected to this part N.G. 以下部品(周辺)の状態・半田付けチェック ・ [IC201] 全てのピン (TAS5066PAGRG4) その他この部品につながる回路 N.G. 以下の部品の状態・半田付けチェック ・ [IC206] 全てのピン (TAS5142DKD) ・ [IC207] 全てのピン (TAS5121DKDR) その他この部品につながる回路 N.G. 以下部品(周辺)の状態・半田付けチェック ・ [RL201,RL202] (DS2SU12VDC) ・ [TR205] (KRC102S) ・ [TR206] (TR206) その他この部品につながる回路 N.G. 以下の部品の状態・半田付けチェック ・ [IC203] (PCM1803DBR) ・ [IC204] (PCM1803DBR) その他この部品につながる回路 N.G. 以下の部品の状態・半田付けチェック ・ [IC101] (RC4580) ・ [IC102] (RC4580) ・ [IC103] (RC4580) その他この部品につながる回路 O.K. O.K. Check Digital amp carrier waveform. • (IC206 33,30pin) • (IC206 26,22pin) • (IC207 29,25pin) Refer (waveform 3) N.G. 以下部品(周辺)の状態・半田付けチェック ・ [X201] (X-TAL) ・ [IC202] (SN74HCU04APWR) ・ [IC201] 2pin 周辺 (TAS5066PAGRG4) ・ [IC203] 15pin 周辺 (PCM1803DBR) ・ [IC204] 15pin 周辺 (PCM1803DBR) その他この部品につながる回路 O.K. O.K. Check PWM sginal waveform. • (IC206 4,5,6pin) • (IC206 14,15,16pin) • (IC207 2,4,17pin) Refer (waveform 2) 以下部品(周辺)の状態・半田付けチェック ・ [IC208] (BD4730) ・ [IC201] 9pin 周辺 (TAS5066PAGRG4) その他この部品につながる回路 O.K. O.K. Check Clock waveform. • (IC201 2pin) • (IC203 15pin) • (IC204 15pin) Refer (waveform 1) N.G. N.G. デジタルアンプキャリア波形の確認 ・ (IC206 33,30pin) ・ (IC206 26,22pin) ・ (IC207 29,25pin) 「波形3」を参照 Check the following parts (and surrounding area) and their soldering. • [IC206] ALL pin (TAS5142DKD) • [IC207] ALL pin (TAS5121DKDR) Also circuits connected to this part O.K. O.K. Check Speaker relay. • Is (RL201,RL202) switched? N.G. スピーカーリレーの確認 ・ (RL201,RL202) 切り替わっているか? Check the following parts (and surrounding area) and their soldering. • [RL201,RL202] (DS2SU12VDC) • [TR205] (KRC102S) • [TR206] (TR206) Also circuits connected to this part O.K. A / D 信号波形の確認 ・ (IC201 24,23,21,19) 「波形4∼6」を参照 O.K. Check A/D signal waveform. • (IC201 24,23,21,19) Refer (waveform 4-6) N.G. Check the following parts (and surrounding area) and their soldering. • [IC203] (PCM1803DBR) • [IC204] (PCM1803DBR) Also circuits connected to this part O.K. 入力回路の確認 ・ (IC101 1,7) ・ (IC102 1,7) ・ (IC103 1,7) DC が出ていない 入力信号がレベル変換されて出ている O.K. Check Input circuit. • (IC101 1,7) • (IC102 1,7) • (IC103 1,7) No DC produced Input signal output with level converted N.G. Check the following parts (and surrounding area) and their soldering. • [IC101] (RC4580) • [IC102] (RC4580) • [IC103] (RC4580) Also circuits connected to this part O.K. 終了 O.K. END 35 S-102 (2) WAVEFORM Waveform 1:Clock Waveform (24.576MHz) (2) 波形図 波形1:クロック波形 (24.576MHz) Waveform 4: A/D Waveform 1 CH1:IC201 CH2:IC201 CH3:IC201 CH4:IC201 CH1:IC201 24pin CH2:IC201 23pin CH3:IC201 21pin CH4:IC201 19pin Waveform 5: A/D Waveform 2(Magnification) 波形2:PWM信号 (パルス幅は入力信号により変化します。) CH1:IC206 4pin, IC20 6 14pin, IC207 2pin CH2:IC206 5pin, IC206 15pin, IC207 4pin CH3:IC206 6pin, IC206 16pin, IC207 1pin CH1:IC201 24pin CH2:IC201 23pin CH3:IC201 21pin CH4:IC201 19pin CH1:IC206 4pin, IC206 14pin, IC207 2pin CH2:IC206 5pin, IC206 15pin, IC207 4pin CH3:IC206 6pin, IC206 16pin, IC207 1pin Waveform 3:Digital amp carrier Waveform Waveform 6: A/D Waveform 3(Magnification) 波形3:デジタルアンプキャリア波形 CH1:IC206 33pin, IC206 26pin, IC206 29pin CH2:IC206 30pin, IC206 22pin, IC206 25pin CH1:IC201 24pin CH2:IC201 23pin CH3:IC201 21pin CH4:IC201 19pin CH1:IC206 33pin,IC206 26pin, IC206 29pin CH2:IC206 30pin,IC206 22pin, IC206 25pin Waveform 2:PWM Signal (Pulse width changed by input signal) 波形4: A/D波形 1 36 24pin 23pin 21pin 19pin 波形5: A/D波形 2(拡大) CH1:IC201 CH2:IC201 CH3:IC201 CH4:IC201 24pin 23pin 21pin 19pin 波形6: A/D波形 3(拡大) CH1:IC201 CH2:IC201 CH3:IC201 CH4:IC201 24pin 23pin 21pin 19pin S-102 (3) 電源 (3) POWER SUPPLY Check FUSE Condition • FUSE (F401)OPEN? N.G. Check Primary Parts and Soldering • [D405] (GSIB660) • [IC401] (SW_TRANS) • [C432] (330/400) for E2 (1000/200) for E3/J • [T401] (SW_TRANS) ヒューズは切れているか? ・ FUSE (F401) N.G. 以下部品(周辺)の状態・半田付けチェック ・ [CX081] (8P-PH) ADV 側の回路のショート若しくは破損 N.G. 以下部品(周辺)の状態・半田付けチェック ・ [T402] (POWER TRANS) ・ [D408 ∼ D410] (RB521S) ・ [C436] (3300/25) その他この出力の負荷となる回路 N.G. 以下部品(周辺)の状態・半田付けチェック ・ [RL401] (DLS9D10_M) ・ [TR401] (KTC3199) ・ [TR402] (KTC3875S) その他この出力の負荷となる回路 N.G. 以下部品(周辺)の状態・半田付けチェック ・ [IC401] (STR-F6267S) 仕向け E2 (STR-F6238S) 仕向け E3/J ・ [D405] (GSIB660) ・ [T401] (SW_TRANS) ・ [IC407] (PC123-Y-22) ・ [IC405] (SE-B2) ・ [D402] (FMX-G22S) ・ [C447.C448] (2200/35) その他この出力の負荷となる回路 N.G. 以下部品(周辺)の状態・半田付けチェック ・ [IC402] 全てのピン (SPI-8002TW) ・ [L404] (7E10H_470M) ・ [C471] (470/16) ・ [D426] (SFPB-74) その他この出力の負荷となる回路 N.G. 以下部品(周辺)の状態・半田付けチェック ・ [IC402] 全てのピン (SPI-8002TW) ・ [L405] (7E10H_470M) ・ [C469] (470/10) ・ [D427] (SFPB-74) その他この出力の負荷となる回路 O.K. O.K. Check FUSE Condition • FUSE (F402)OPEN? N.G. 一次側の回路部品の破損 ・ [D405] (GSIB660) ・ [IC401] (SW_TRANS) ・ [C432] (330/400)仕向け E2 (1000/200)仕向け E3/J ・ [T401] (SW_TRANS) N.G. Check the following parts (and surrounding area) and their soldering. • [CX081] (8P-PH) Short-circuit or damaged wire in ADV side circuit ヒューズは切れているか? ・ FUSE (F402) O.K. O.K. Check +9V_NSW Output • Voltage Check +9V_NSW DC (non-switched) Voltage is O.K.? (CX151 14pin output) N.G. Check the following parts (and surrounding area) and their soldering. • [T402] (POWER_TRANS) • [D408,D410] (RB521S) • [C436] (3300/25) and Other Circuits +9V_NSW 出力電圧は正常か? ・ (CX151 14pin 出力 ) O.K. O.K. Check Power relay. • IS (RL401) switched? N.G. パワーリレーの確認 ・ (RL401) が切り替わっているか? Check the following parts (and surrounding area) and their soldering. • [RL401] (DLS9D10_M) • [TR401] (KTC3199) • [TR402] (KTC3875S) and Other Circuits O.K. O.K. Check +HB(about 31V) Output • Voltage Check +HB(about 31V) DC (non-switched) Voltage is O.K.? (CX081 6pin output) N.G. Check the following parts (and surrounding area) and their soldering. • [IC401] (STR-F6267S) for E2 (STR-F6238S) for E3/J • [D405] (GSIB660) • [T401] (SW_TRANS) • [IC407] (PC123-Y-22) • [IC405] (SE-B2) • [D402] (FMX-G22S) • [C447.C448] (2200/35) and Other Circuits +HB( 約 31V) 出力電圧は正常か? ・(CX081 6pin 出力 ) O.K. +12V_D 出力電圧は正常か? ・ (L404 C471 側 ) O.K. Check +12V_D Output • Voltage Check +12V_D DC (non-switched) Voltage is O.K.? (L404 C471 side) N.G. Check the following parts (and surrounding area) and their soldering. • [IC402] ALL pin (SPI-8002TW) • [L404] (7E10H_470M) • [C471] (470/16) • [D426] (SFPB-74) and Other Circuits O.K. +3.3V_D 出力電圧は正常か? ・ (L405 C469 側 ) O.K. Check +3.3V_D Output • Voltage Check +3.3V_D DC (non-switched) Voltage is O.K.? (L405 C469 side) N.G. Check the following parts (and surrounding area) and their soldering. • [IC402] ALL pin (SPI-8002TW) • [L405] (7E10H_470M) • [C469] (470/10) • [D427] (SFPB-74) and Other Circuits O.K. O.K. 37 S-102 Check +12V_A Output • Voltage Check +12V_A DC (non-switched) Voltage is O.K.? (IC403 O Terminal (Output Terminal)) N.G. Check the following parts (and surrounding area) and their soldering. • [T401] (SW_TRANS) • [IC403] (KIA7812API) • [D418] RN-1Z and Other Circuits +12V_A 出力電圧は正常か? ・ (IC403 O 端子 ( 出力端子 )) N.G. 以下部品(周辺)の状態・半田付けチェック ・ [T401] (SW_TRANS) ・ [IC403] (KIA7812API) ・ [D418] RN-1Z その他この出力の負荷となる回路 N.G. 以下部品(周辺)の状態・半田付けチェック ・ [T401] (SW_TRANS) ・ [IC404] (KIA7912PI) ・ [D419] RN-1Z その他この出力の負荷となる回路 N.G. 以下部品(周辺)の状態・半田付けチェック ・ [IC205] (KIA7805API) その他この出力の負荷となる回路 O.K. O.K. Check -12V_A Output • Voltage Check -12V_A DC (non-switched) Voltage is O.K.? (IC404 O Terminal (Output Terminal)) N.G. Check the following parts (and surrounding area) and their soldering. • [T401] (SW_TRANS) • [IC404] (KIA7912PI) • [D419] RN-1Z and Other Circuits -12V_A 出力電圧は正常か? ・ (IC404 O 端子 ( 出力端子 )) O.K. O.K. Check +5V_A Output • Voltage Check +5V_A DC (non-switched) Voltage is O.K.? (IC205 O Terminal (Output Terminal)) N.G. +5V_A 出力電圧は正常か? ・ (IC205 O 端子 ( 出力端子 )) Check the following parts (and surrounding area) and their soldering. • [IC205] (KIA7805API) and Other Circuits O.K. 終了 O.K. END 38 S-102 ELECTRICAL ADJUSTMENT FOR VIDEO ビデオ回路の調整 1. SETTING 1. セッティング手順 (1) Connect the monitor TV to the video output terminal. (2) Connect the oscilloscope to the Y-signal and C-signal of S-VIDEO output terminal and each terminate at 75 Ohms. (3) Connect the oscilloscope to the Y-signal, PB-signal and PR-signal of Component video output terminal and each terminate at 75 Ohms. ※ Use the 75 Ohms resistance must be 1% (4) DVD test disc : VT502 (1) セットの VIDEO OUT 端子にテレビモニターを接続する。 (2) セットの S2 VIDEO OUT 端子から Y 信号と C 信号をそ れぞれオシロスコープ(終端抵抗:75Ω)に接続する。 (3) セットの COMPONENT VIDEO OUT の端子(Y/PB/PR) をそれぞれオシロスコープ(終端抵抗:75Ω)に接続 する。 ※ 75Ω 抵抗は 1%品を使用する事。 (4) DVD テストディスク:VT502 を用意する。 2. BEFORE ADJUSTMENT 2. 調整のまえに 2.1. Setting the Oscilloscope as below. 2.1. オシロスコープを下記に設定する。 (1) PB/PR (a) TIME/DIV : 20μS (b) VOLT/DIV : 100mV (プローブ x10 使用) (2) Y (a) TIME/DIV : 20μS (b) VOLT/DIV : 200mV (プローブ x10 使用) (3) C (a) TIME/DIV : 20μS (b) VOLT/DIV : 50mV (プローブ x10 使用) 電源電圧 :100V (Japan) :120V (U.S.A. & Canada) :230V (Europe & Asia) :220V (China) (1) PB/PR (a) TIME/DIV : 20µS (b) VOLT/DIV : 100mV (Use the probe : x10 ) (2) Y (a) TIME/DIV : 20µS (b) VOLT/DIV : 200mV (Use the probe : x10 ) (3) C (a) TIME/DIV : 20µS (b) VOLT/DIV : 50mV (Use the probe : x10 ) Power on. Power Supply U.S.A. & Canada : 120V Europe & Asia : 230V China : 220V Japan : 100V 2.2. 準備手順 2.2. Preparation (1) Power on. (2) Check the Component output signal is progressive. (“PROGRESSIVE” is shown on the FL display) (3) Check the HDMI output is off. (“HDMI” is not shown on the FL display) (4) Push [ ] button, then open the Disc Tray. Set DVD test disc (VT502) on the Disc Tray, and then push [ ] button. (5) FL display appear “STOP”, push [ ] button to playback DVD. (6) Press the remote control unit [CALL] button twice to display the title number. (7) Press the remote control unit [ ] cursor button to select the title number to be played. (8) Push the [3] button, select title 3 of DVD. (9) Push the [ENTER] button, playback title 3. (color bar 100%) 39 (1) セットの AC コードをコンセントへ挿入し、セットの電 源を ON する。 (2) セットの COMPONENT VIDEO OUT 端子の出力が PROGRESSIVE になっていることを確認する。 (FL 管の "PROGRESSIVE" が点灯していること ) (3) HDMI 出力が OFF になっていることを確認する。 (FL 管の "HDMI" が消灯していること ) (4) セットの「 」ボタンを押しトレイを開き、トレイ上 に DVD テストディスク(VT502)をセット後、 「 」 ボタンを押す。 (5) セット表示管上に "STOP" が表示されてから、「 」ボ タンを押し、ディスクを再生する。 (6) リモコンの「CALL」ボタンを 2 回押し、Title ナンバー を表示する。 (7) リモコンのカーソル「 」ボタンを押して、Title ナン バーを選択する。 (8) 番号ボタンの [3] ボタンを押し、Title 3 を選択する。 (9) 「ENTER」ボタンを押し、Title 3 を再生する(100%カ ラーバー信号)。 S-102 3. PROCEDURE 3. 手順 (1) Adjust the signal of S-VIDEO out by the wave of oscilloscope. (1) セットの S2 VIDEO OUT の信号レベルをオシロスコープ 上の波高値で調整する。 (a) Target, Y-signal Point Adjustment Value Waveform : : (a) Y 信号レベル 調整個所 調整値 波形 VR801 1000 ± 20mV :VR801 :1000 ± 20mV Y Y Y-signal of S-VIDEO out S2 VIDEO OUT の Y 信号レベル (b) Target, C-signal Point Check Value Waveform : : (b) C 信号レベル 調整個所 確認 波形 VR802 286 ± 10mV :VR802 :286 ± 10mV C C C-signal of S-VIDEO out S2 VIDEO OUT の C 信号レベル (2) Adjust the signal of COMPONENT OUT (PROGRESSIVE) by the wave of oscilloscope. (2) COMPONENT OUT (PROGRESSIVE) の信号レベルをオシ ロスコープ上の波高値で調整する。 (a) Target, Y-signal Point Adjustment Value Waveform : : (a) Y 信号レベル 調整個所 調整値 波形 VR803 1000 ± 20mV Y Y Y-signal プログレッシブの Y 信号レベル (b) Target, PB-signal Point Check Value Waveform : : :VR803 :1000 ± 20mV (b) PB 信号レベル 調整個所 確認 波形 VR804 700 ± 10mV PB :VR804 :700 ± 10mV PB PB-signal PB 信号レベル 40 S-102 (c) Target, PR-signal Point Check Value Waveform : : (c) PR 信号レベル 調整個所 調整値 波形 VR805 700 ± 10mV :VR805 :700 ± 10mV PR PR PR 信号レベル PR-signal 41 S-102 BLOCK DIAGRAMS ADV-S102 42 4580 4580 FR IN SW IN 43 AC IN 50/60Hz +9V_NSW 4580 FL IN SMPS 24.576MHz PCM1803 PCM1803 Internal PS TAS5066 Internal SP DSW-S102 Block Diagram TAS5121 TAS5142 FR FL S-102 DSW-S102 Sub Woofer -20dBFs -20dBFs 200mV 44 -35dBFs -30dBFs -20dBFs -10dBFs 0dBFs -10dBFs Front 0dBFs Total +37.8dB +35.0dB +20.0dB +17.2dB +14.8dB S-102 LEVEL DIAGRAM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 VEE HA2/AUX4[4] VEE I2CDATA/AUX0 I2C_CLK/AUX1 AUX2/IOW# VSS VEE AUX3/IOR# AUX4 AUX5 AUX6 AUX7 LOE# VSS VCC LCS0#/PIXOUT_CLK LCS1# LCS2# LCS3# VSS LD0 LD1 LD2 LD3 LD4 VEE VSS LD5 LD6 LD7 LD8 LD9 LD10 LD11 VSS VEE LD12 LD13 LD14 LD15 LWRLL# LWRHL# VSS VEE CAMIN0/PIXIN0 CAMIN1/PIXIN1 LA0 LA1 LA2 LA3 VSS VEE LA4 LA5 LA6 LA7 LA8 LA9 VSS VCC LA10 LA11 LA12 LA13 LA14 LA15 LA16 VSS VEE LA17 LA18 LA19 LA20 LA21 RESET# TDMDX/RSEL VSS VEE TDMDR TDMCLK TDMFS TDMTSC# TWS/SEL_PLL2 TSD0/SEL_PLL0 VSS VCC TSD1/SEL_PLL1 TSD2 TSD3 MCLK TBCK SEL_PLL3/SPDIF_OUT SPDIF_IN VSS VCC RSD RWS RBCK CAMIN3/PIXIN3 XIN XOUT AVEE AVSS 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 VSS HA1/AUX4[3] HA0/AUX4[2] HCS3FX#/AUX3[6] HCS1FX#/AUX3[7] HIOCS16#/AUX3[4]/CAMCLK/PIXIN_CLK HRD#/DCI_ACK#/AUX4[6] HWR#/DCI_CLK/AUX4[5] VEE VSS HIORDY/AUX3[3] HRST#/AUX3[5] HIRQ/DCI_ERR#/AUX4[7] HRRQ#/AUX4[0]/CAMIN2/PIXIN2 HWRQ#/DCI_REQ#/AUX4[1] HD15/AUX2[7]/IR HD14/AUX2[6] VCC VSS HD13/AUX2[5]/SP HD12/AUX2[4]/C2PO HD11/AUX2[3]//IRQ HD10/AUX2[2] HD9/AUX2[1] HD8/DCI_FDS#/AUX2[0]/VFD_CLK HD7/DCI7/AUX1[7]/VFD_DIN VEE VSS HD6/DCI6/AUX1[6]/VFD_DOUT HD5/DCI5/AUX1[5] HD4/DCI4/AUX1[4] HD3/DCI3/AUX1[3] HD2/DCI2/AUX1[2] HD1/DCI1/AUX1[1] HD0/DCI0/AUX1[0] VCC VSS HSYNC#/AUX3[0]/CAMIN7/PIXIN7 VSYNC#/AUX3[1]/CAMIN6/PIXIN6 PCLKQSCN/AUX3[2]/CAMIN5/PIXIN5 PCLK2XSCN/CAMIN4/PIXIN4 FDAC/YUV7/PIXOUT7 VDAC/YUV6/PIXOUT6 YDAC/YUV5/PIXOUT5 ADVSS ADVEE RSET/YUV4/PIXOUT4 COMP/YUV3/PIXOUT3 CDAC/YUV2/PIXOUT2 VREF/YUV1/PIXOUT1 UDAC/YUV0/PIXOUT0 DCLK S-102 SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. 主な半導体を記載しています。汎用の半導体は記載を省略しています。 1. IC’s ES6178FF (IC101: 1U-3836) PINOUT DIAGRAM 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 ES6178 45 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 VEE VSS DSCK DQM DCS0# VEE VSS DCS1# DB15 DB14 DB13 DB12 VEE VSS DB11 DB10 DB9 DB8 DB7 DB6 VSS VCC DB5 DB4 DB3 DB2 DB1 DB0 VSS VEE DMBS1 DMBS0 DRAS# DWE# DOE#/DSCK_EN DCAS# VEE VSS DMA11 DMA10 DMA9 DMA8 DMA7 DMA6 VSS VEE DMA5 DMA4 DMA3 DMA2 DMA1 DMA0 S-102 ES6178FF PIN DESCRIPTION Name Pin Numbers I/O 1,18, 27, 59, 68, 75, 92, 99, 104, 130, 148, 157, 159, 164, 183, 193, 201 P I/O power supply. 2-7, 10-16, 19-23, 204-207 O RISC port address bus. 8, 17, 26, 34, 43, 60, 67, 76, 84, 91, 98, 103, 120, 129, 138, 147, 156, 163, 171, 177, 184, 192, 200, 208 G Ground. 9, 35, 44, 83, 121, 139, 172 P Core power supply. 24 I Reset input; (5V tolerant input). TDMDX O TDM transmit data output. RSEL I LCS3 ROM Boot Data Width Select. Strapped to VCC or ground via 4.7-k: resistor; read only during reset. VEE LA[21:0] VSS VCC RESET# Definition RSEL 25 Selection 0 16-bit ROM 1 8-bit ROM TDMDR 28 I TDM receive data input; (5V tolerant input). TDMCLK 29 I TDM clock input; (5V tolerant input). TDMFS 30 I TDM frame sync input; (5V tolerant input). TDMTSC# 31 O TDM output enable. TWS O Audio transmit frame sync output. SEL_PLL2 I System and DSCK output clock frequency selection is made at the rising edge of RESET#. The matrix below lists the available clock frequencies and their respective PLL bit settings. Strapped to VCC or ground via 4.7-k: resistor; read only during reset. 32 SEL_PLL2 SEL_PLL1 SEL_PLL0 0 0 0 DCLK u.5 0 0 1 DCLK u 5.0 0 1 0 Bypass 0 1 1 DCLK u4.0 1 0 0 DCLK u4.25 1 0 1 DCLK u4.75 1 1 0 DCLK u 5.5 1 1 1 DCLK u6.0 46 PLL Settings S-102 Name Pin Numbers TSD0 I/O Definition O Audio transmit serial data output 0. I Refer to the description and matrix for SEL_PLL2 pin 32. O Audio transmit serial data output 1. I Refer to the description and matrix for SEL_PLL2 pin 32. 33 SEL_PLL0 TSD1 36 SEL_PLL1 TSD2 37 O Audio transmit serial data output 2. This pin must be pulled down to VSS via a 4.7-k: resistor for proper operation. TSD3 38 O Audio transmit serial data output 3. MCLK 39 I/O Audio master clock for audio DAC. TBCK 40 I/O Audio transmit bit clock. TBCK is an input during reset and subsequently is programmed as an output via the AUDIOXMT register (addr 0x2000D00Ch, bit 4). I Clock source select. Strapped to VCC or ground via 4.7-k: resistor; read only during reset. SEL_PLL3 SEL_PLL3 41 SPDIF_OUT Clock Source 0 Crystal oscillator 1 DCLK input O S/PDIF output. SPDIF_IN 42 I S/PDIF input; (5V tolerant input). RSD 45 I Audio receive serial data; (5V tolerant input). RWS 46 I Audio receive frame sync; (5V tolerant input). RBCK 47 I Audio receive bit clock; (5V tolerant input). I Camera YUV 3. I CCIR656 input pixel 3. CAMIN3 48 PIXIN3 XIN 49 I 27-MHz crystal input. XOUT 50 O 27-MHz crystal output. AVEE 51 P Analog power for PLL. AVSS 52 G Analog ground for PLL. 53-58, 61-66 O DRAM address bus. 69 O DRAM column address strobe. O DRAM output enable. O DRAM clock enable. DMA[11:0] DCAS# DOE# 70 DSCK_EN DWE# 71 O DRAM write enable. DRAS# 72 O DRAM row address strobe. DMBS0 73 O DRAM bank select 0. DMBS1 74 O DRAM bank select 1. DB[15:0] 77-82, 85-90, 93-96 I/O DRAM data bus. 97,100 O DRAM chip select. DQM 101 O Data input/output mask. DSCK 102 O Output clock to DRAM. DCS[1:0]# 47 S-102 Name Pin Numbers I/O DCLK 105 I Clock input to PLL; (5V tolerant input). O Video DAC output. UDAC 106 Definition Value F DAC (pin 115) V DAC (pin 114) Y DAC C DAC U DAC (pin 113) (pin 108) (pin 106) 0 CVBS/Chroma CVBS1 Y C N/A 1 CVBS/Chroma CVBS1 Y C CVBS2 2 CVBS/Chroma N/A Y C N/A 3 CVBS/Chroma CVBS1 N/A N/A CVBS2 4 CVBS/Chroma CVBS1 N/A N/A N/A 5 CVBS/Chroma CVBS1 Y Pb Pr 6 CVBS/Chroma N/A Y Pb Pr 7 N/A SYNC G B R 8 CVBS/Chroma Chroma Y Pb Pr 9 CVBS CVBS1 G B R 10 CVBS CVBS1 G R B 11 N/A SYNC G R B 12 CVBS/Chroma N/A Y Pr Pb 13 CVBS/Chroma CVBS1 Y Pr Pb 14 Chroma Y G R B F: CVBS/chroma signal for simultaneous mode. Y: Luma component for YUV and Y/C processing. C: Chrominance signal for Y/C processing. U: Chrominance component signal for YUV mode. V: Chrominance component signal for YUV mode. YUV0 O YUV pixel 0 output data. PIXOUT0 O CCIR656 output pixel 0. VREF I Internal voltage reference to video DAC. Bypass to ground with 0.1-PF capacitor. O YUV pixel 1 output data. PIXOUT1 O CCIR656 output pixel 1. CDAC O Video DAC output. Refer to description and matrix for UDAC pin 106. O YUV pixel 2 output data. PIXOUT2 O CCIR656 output pixel 2. COMP I Compensation input. Bypass to ADVEE with 0.1-PF capacitor. O YUV pixel 3 output data. PIXOUT3 O CCIR656 output pixel 3. RSET I DAC current adjustment resistor input. O YUV pixel 4 output data. O CCIR656 output pixel 4. YUV1 YUV2 YUV3 YUV4 PIXOUT4 107 108 109 110 48 S-102 Name Pin Numbers I/O ADVEE 111 P Analog power for video DAC. ADVSS 112 G Analog ground for video DAC. O Video DAC output. Refer to description and matrix for UDAC pin 106. O YUV pixel 5 output data PIXOUT5 O CCIR656 output pixel 5. VDAC O Video DAC output. Refer to description and matrix for UDAC pin 106. O YUV pixel 6 output data. PIXOUT6 O CCIR656 output pixel 6. FDAC O Video DAC output. Refer to description and matrix for UDAC pin 106. O YUV pixel 7 output data. PIXOUT7 O CCIR656 output pixel 7. PCLK2XSCN I/O 27-MHz video output pixel clock. YDAC YUV5 YUV6 YUV7 CAMIN4 113 114 115 116 Definition I Camera YUV 4. PIXIN4 I CCIR656 input pixel 4. PCLKQSCN O 13.5-MHz video output pixel clock. I/O Aux3 data I/O; (5V tolerant input). AUX3[2] 117 CAMIN5 I Camera YUV 5. PIXIN5 I CCIR656 input pixel 5. VSYNC# AUX3[1] I/O Vertical sync; (5V tolerant input). I/O Aux3 data I/O; (5V tolerant input). 118 CAMIN6 I Camera YUV 6. PIXIN6 I CCIR656 input pixel 6. HSYNC# AUX3[0] I/O Horizontal sync; (5V tolerant input). I/O Aux3 data I/O; (5V tolerant input). 119 CAMIN7 I Camera YUV 7. PIXIN7 I CCIR656 input pixel 7. HD[5:0] I/O Host data bus lines; (5V tolerant input). I/O DVD channel data I/O; (5V tolerant input). AUX1[5:0] I/O Aux1 data I/O; (5V tolerant input). HD6 I/O Host data bus line; (5V tolerant input). I/O DVD channel data I/O; (5V tolerant input). I/O Aux1 data I/O; (5V tolerant input). DCI[5:0] 122-127 DCI6 128 AUX1[6] VFD_DOUT I HD7 VFD data output. I/O Host data bus line; (5V tolerant input). I/O DVD channel data I/O; (5V tolerant input). AUX1[7] I/O Aux1 data I/O; (5V tolerant input). VFD_DIN I DCI7 131 VFD data input. 49 S-102 Name Pin Numbers HD8 DCI_FDS# I/O Definition I/O Host data bus line; (5V tolerant input). I/O DVD input sector start; (5V tolerant input). I/O Aux2 data I/O; (5V tolerant input). 132 AUX2[0] VFD_CLK I HD9 VFD clock input. I/O Host data bus line; (5V tolerant input). I/O Aux2 data I/O; (5V tolerant input). I/O Host data bus line; (5V tolerant input). AUX2[2] I/O Aux2 data I/O; (5V tolerant input). HD11 I/O Host data bus line; (5V tolerant input). I/O Aux2 data I/O; (5V tolerant input). IRQ O IRQ. HD12 I/O Host data bus line; (5V tolerant input). I/O Aux2 data I/O; (5V tolerant input). 133 AUX2[1] HD10 134 AUX2[3] AUX2[4] 135 136 C2PO I HD13 I/O Host data bus line; (5V tolerant input). I/O Aux2 data I/O; (5V tolerant input). AUX2[5] 137 SP I HD14 C2PO error correction flag from CD-ROM; (5V tolerant input). 16550 UART serial port input. I/O Host data bus line; (5V tolerant input). AUX2[6] I/O Aux2 data I/O; (5V tolerant input). HD15 I/O Host data bus line; (5V tolerant input). I/O Aux2 data I/O; (5V tolerant input). 140 AUX2[7] 141 IR I IR remote control input; (5V tolerant input). HWRQ# O Host write request. O DVD control interface request. AUX4[1] I/O Aux4 data I/O; (5V tolerant input). HRRQ# O Host read request. I/O Aux4 data I/O; (5V tolerant input). DCI_REQ# 142 AUX4[0] 143 CAMIN2 I Camera YUV 2. PIXIN2 I CCIR656 input pixel 2. HIRQ DCI_ERR# 144 AUX4[7] HRST# I/O Host interrupt. I/O DVD channel data error; (5V tolerant input). I/O Aux4 data I/O; (5V tolerant input). O Host reset. I/O Aux3 data I/O; (5V tolerant input). 145 AUX3[5] HIORDY I Host I/O ready. 146 AUX3[3] I/O Aux3 data I/O; (5V tolerant input). 50 S-102 Name Pin Numbers I/O Definition I/O Host write. I/O DVD channel data clock; (5V tolerant input). AUX4[5] I/O Aux4 data I/O; (5V tolerant input). HRD# O Host read. I/O DVD channel data valid; (5V tolerant input). I/O Aux4 data I/O; (5V tolerant input). HWR# DCI_CLK DCI_ACK# 149 150 AUX4[6] HIOCS16# I AUX3[4] I/O Device 16-bit data transfer. Aux3 data I/O; (5V tolerant input). 151 CAMCLK I Camera port pixel clock input. PIXIN_CLK I CCIR656 input pixel clock. O Host select 1. I/O Aux3 data I/O; (5V tolerant input). O Host select 3. I/O Aux3 data I/O; (5V tolerant input). I/O Host address bus. I/O Aux4 data I/Os; (5V tolerant input). I/O Auxiliary port 0 (open collector); (5V tolerant input). I/O I2C data I/O; (5V tolerant input). I/O Auxiliary port 1 (open collector); (5V tolerant input). I/O I2C clock I/O; (5V tolerant input). I/O Auxiliary port; (5V tolerant input). O I/O write strobe (LCS1). I/O Auxiliary port; (5V tolerant input). O I/O read strobe (LCS1). 166-169 I/O Auxiliary ports; (5V tolerant input). 170 O RISC port output enable. O RISC port chip select 0. O CCIR656 output pixel clock. 174-176 O RISC port chip select [3:1]. LD[15:0] 178-182, 185-191, 194-197 I/O RISC port data bus; (5V tolerant input). LWRLL# 198 O RISC port low-byte write enable. LWRHL# 199 O RISC port high-byte write enable. I Camera YUV 0. I CCIR656 input pixel 0. I Camera YUV 1. I CCIR656 input pixel 1. HCS1FX# 152 AUX3[7] HCS3FX# 153 AUX3[6] HA[2:0] 154, 155, 158 AUX4[4:2] AUX0 160 I2CDATA AUX1 161 I2C_CLK AUX2 162 IOW# AUX3 165 IOR# AUX4-7 LOE# LCS0# 173 PIXOUT_CLK LCS[3:1]# CAMIN0 202 PIXIN0 CAMIN1 203 PIXIN1 51 S-102 DSP21367 (IC401: 1U-3836) 52 S-102 M30627FHPGP (IC301: 1U-3836) Pin No Port Function Port setting Port Name VREF Explanation 1 VREF - Reference Voltage Input for A/D converter 2 AVCC - AVCC Positive power 3 P97/SIN4 I DSP_MISO Serial Data input from DSP 4 P96/SOUT4 O DSP_MOSI Serial Data output to DSP 5 P95/CLK4 O DSP_CK Serial Clock output to DSP 6 P94 O DSP_PWR [DSP Power ON/OFF output] 7 P93 O FL_CS Chip Enable output to FLD 8 P92/SOUT3 O FL_DOUT Serial Data output to FLD 9 P91/SIN3 O /FL_RST Reset output to FLD 10 P90/CLK3 O FL_CLK Serial Clock output to FLD 11 P141 O /VMONI_SELB Select signal output of VIDEO OUTPUT(L:AUX1/2,H:DVD). 12 P140 O /FLI_RST Reset output to FLI2310 13 BYTE - BYTE GND Select input of Flash Memory write Mode 14 CNVCS - CNVSS 15 P87 O ON/_STBY Main POWER ON/STANDBY switching output. H:ON 16 P86 O /VMONI_SELA Select signal output of VIDEO OUTPUT (H:AUX1, L:AUX2) 17 RESET I RST Reset input 18 XOUT O X1 Xtal output 19 VSS - VSS GND 20 XIN I X2 Xtal input 21 VCC1 - VCC1 Positive power 22 P85/NMI I /NMI Positive power 23 P84/INT2 I /DIR_INT Interrupt input from DIR 24 P83/INT1 INT /BE_AUDIO_RST Audio Reset input from ESS 25 P82/INT0 INT BE_CS CS Interrupt input from ESS 53 S-102 Pin No Port Function Port setting Port Name Explanation 26 P81 EC 27 P80 I P_DOWN( 50/60Hz ) 50Hz/60Hz AC input PWB_CHK Checking PWB input 28 P77 O /SMONI_SELB SelecteYC Video outputB 29 P76 O /SMONI_SELA Selecte YC Video outputA 30 P75 I VOL_B VOL encoder Pulse-B input 31 P74 I VOL_A VOL encoder Pulse-A input 32 P73/CTS2 O NC(L:Output) Not Used:N.C. 33 P72/CLK2 I /TEMP_DET Temperature Detect signal input from posister 34 P71/RXD2 I IPOD_D_MRXD Serial Data input from IPOD 35 P70/TXD2 O IPOD_D_MTXD Serial Data output to IPOD 36 P67/TXD1 O F_TXD2 Serial Data out to Flash Memory. 37 VCC1 - VCC1 Positive power 38 P66 O F_RXD2 Serial Data input from Flash Memory. 39 VSS - VSS GND 40 P65 O LED_ORG Orenge(Yellow)LED output. L:ON 41 P64 O DC/DC_ON Power ON/OFF output to DC/DC Converter. H: Power ON 42 TXD0 SO BE_STXD Serial Data output to ESS 43 RXD0 SI BE_SRXD Serial Data input from ESS 44 CLK0 SI BE_CLK Serial Clock input from ESS 45 P60/CTS0 O NC(L:Output) Not Used:N.C. 46 P137 O NC(L:Output) Not Used:N.C. 47 P136 O HD/_SD Select signal output of Video Encoder Clock ( L:SD, H:HD) 48 P135 O /CHOP_ON CHOPER REG. ON/OFF output. L:ON 49 P134 O HDMI_DEBG6 For HDMI Debug 50 P57 O /ENC_RST Video Encoder Reset output 51 P56 O NC(L:Output) Not Used:N.C. 52 P55/EPM O F_EPM2 Writing Port for Flash Memory. 53 P54 I AUX_SW Front AUX IN insert detect signal input. H: Detected 54 P133 I HP_SW HEAD PHONE insert detect signal input. H: Detected 55 P132 O NC(L:Output) Not Used:N.C. 56 P131 O HDMI_OE HDMI Output Enable(Active Low) 57 P130 O /VPLD_RST Reset output to VPLD. 58 P53 O NC(L:Output) Not Used:N.C. 59 P52 O LED_RED Red LED output. L:ON Blue LED output. H:ON 60 P51 O LED_BLU 61 P50/CE O /F_CE2 Chip Enable output to Flash Memory. 62 P127 O NC(L:Output) Not Used:N.C. 63 P126 O E2P_CS Chip Select output to EEPROM 64 P125 O SAN_CE Chip Enable output to TUNER/RDS IC 65 P47 O E2P_CLK Serial Clock output to EEPROM 66 P46 O E2P_MOSI Serial Data output to EEPROM 67 P45 O FNVL_DA Serial Data output to FUNC/VOL IC. 68 P44 O FNVL_CK Serial Clock output to FUNC/VOL IC. 69 P43 O FNVL_CE Chip Enable output to FUNC/VOL IC. 70 P42 I E2P_MISO Serial Data input to EEPROM 71 P41 I SAN_MISO Serial Data input from TUNER/RDS IC 72 P40 I TU_STEREO "STEREO" indicator input from FM/AM TUNER pack 73 P37 I TUNED "TUNED" detect input from FM/AM TUNER pack 74 P36 O /TU_MU MUTE output to TUNER. L:MUTE 75 P35 O TU_POWER TUNER Power ON/OFF output. H: Power ON 76 P34 O /SAN_RST Reset output to TUNER/RDS IC 77 P33 O SP_RL SP RELAY ON/OFF output. H:ON 78 P32 I CODEC_MISO Serial Data input from CODEC 79 P31 O NC(L:Output) Not Used:N.C. 80 P124 O SAN_CK Serial Clock output to TUNER/RDS IC 54 S-102 Pin No Port Function Port setting Port Name Explanation 81 P123 O SAN_MOSI Serial Data output to TUNER/RDS IC 82 P122 O /CODEC_RST Reset output to CODEC 83 P121 O PRE_MUTE_SUB MUTE output to PRE OUT. H:MUTE 84 P120 O HP_MUTE_SUB MUTE output to HEAD PHONE output. H:MUTE 85 VCC2 - VCC2 Positive power 86 P30 O BE/_DIR Select audio line output.(H:ESS,L:DIR) GND 87 VSS - VSS 88 P27 O CODEC_CE Chip Enable output to CODEC 89 P26 O NC(L:Output) Not Used:N.C. 90 P25 O DSP_IO_MUTE DSP IO MUTE output(H:Mute) Select audio line output.(H:DIGITAL, L:ADC IN) 91 P24 O /AD/DIG 92 P23 O /ERR_MUTE MUTE output at DSP Error. 93 P22 O /BSE Bit Stream Enable output(L:Enable) 94 P21 O NC(L:Output) Not Used:N.C. 95 P20 O NC(L:Output) Not Used:N.C. 96 INT5 INT 97 P16 98 /PROTECT Protect Signal input. O NC(L:Output) Not Used:N.C. INT3 INT /REMOCON Remote Control signal input 99 P14 O NC(L:Output) Not Used:N.C. 100 P13 O PRE_MUTE_MAIN MUTE output to Output(H:Mute). 101 P12 O /COMP_MUTE COMPONENT VIDEO Mute output(H:Mute) 102 P11 O /S/V_MUTE S/COMPOSITE VIDEO Mute output(H:Mute) Reset output to ESS 103 P10 O /BE RST 104 P07 O DRV_ON DRIVE POWER ON output(H:P.ON) 105 P06 O SYS_REQ SYSTEM REQEST output to ESS. 106 P05 I BE ON Active Flag input from ESS. 107 P04 O NC(L:Output) Not Used:N.C. 108 P03 O NC(L:Output) Not Used:N.C. 109 P02 O /DIR_RST Reset output to DIR. 110 P01 O DIR_CE Chip Enable output to DIR Serial Clock output to DIR/CODEC. 111 P00 O DIR/CODEC_CK 112 P117 I DIR_MISO Serial Data input from DIR. 113 P116 O DIR/CODEC_MOSI Serial Data output to DIR/CODEC 114 P115 O /DSPROM_RST Reset output to DSP ROM. 115 P114 O /DSP_RST Reset output to DSP. 116 P113 O DSP_CS Chip Select output to DSP 117 P112 I FLAG0 DSP FLAG0 input 118 P111 O FAN_ON FAN ON/OFF output.H:FAN ON FAN SPEED Control output(H:Slow L:Fast) 119 P110 O FAN SPEED 120 P107/AN7 I Pull uÇê Pull up 121 P106/AN6 AD KEY2 Unit Operation Button input2 122 P105/AN5 AD KEY1 Unit Operation Button input1 123 P104/AN4 AD KEY0 Unit Operation Button input0 124 P103/AN3 AD MODE2_S102 Initial Setting input for Region No of DVD. 125 P102/AN2 AD MODE1_S102 Initial Setting input the destination.(E2,E3) 126 P101/AN1 O Pull up Pull up 127 AVSS 128 SW1_IN AD AVSS GND SW1_IN Select signal input of Video Signal. (H:HDMI/M:PROGRE/L:INTERLACE) [ ]:Reserved 55 S-102 W9864G2GH-7 (IC402: 1U-3836) PIN DESCRIPTION PIN NAME A0−A10 FUNCTION Address DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. A10 is sampled during a precharge command to determine if all banks are to be precharged or bank selected by BS0, BS1. BS0, BS1 Bank Select Select bank to activate during row address latch time, or bank to read/write during address latch time. DQ0−DQ31 Data Input/ Output Multiplexed pins for data output and input. CS Chip Select Disable or enable the command decoder. When command decoder is disabled, new command is ignored and previous operation continues. RAS Row Address Strobe Command input. When sampled at the rising edge of the clock RAS , CAS and WE define the operation to be executed. CAS Column Address Strobe Referred to RAS WE Write Enable Referred to RAS DQM0− Input/output mask The output buffer is placed at Hi-Z (with latency of 2) when DQM is sampled high in read cycle. In write cycle, sampling DQM high will block the write operation with zero latency. DQM3 CLK Clock Inputs System clock used to sample inputs on the rising edge of clock. CKE Clock Enable CKE controls the clock activation and deactivation. When CKE is low, Power Down mode, Suspend mode, or Self Refresh mode is entered. VCC Power (+3.3V) Power for input buffers and logic circuit inside DRAM. VSS Ground Ground for input buffers and logic circuit inside DRAM. VCCQ Power (+3.3V) for Separated power from VCC, to improve DQ noise immunity. I/O buffer VSSQ Ground for I/O buffer Separated ground from VSS, to improve DQ noise immunity. NC No Connection No connection 56 S-102 K4S641632 (IC103: 1U-3836) ( p VDD DQ0 VDDQ DQ1 DQ2 VSSQ DQ3 DQ4 VDDQ DQ5 DQ6 VSSQ DQ7 VDD LDQM WE CAS RAS CS BA0 BA1 A10/AP A0 A1 A2 A3 V DD ) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 VSS DQ15 VSSQ DQ14 DQ13 VDDQ DQ12 DQ11 VSSQ DQ10 DQ9 VDDQ DQ8 VSS N.C/RFU UDQM CLK CKE N.C A11 A9 A8 A7 A6 A5 A4 VSS 54Pin TSOP (II) (400mil x 875mil) (0.8 mm Pin pitch) PIN FUNCTION DESCRIPTION Pin Name Input Function CLK System clock Active on the positive going edge to sample all inputs. CS Chip select Disables or enables device operation by masking or enabling all inputs except CLK, CKE and L(U)DQM CKE Clock enable Masks system clock to freeze operation from the next clock cycle. CKE should be enabled at least one cycle prior to new command. Disable input buffers for power down in standby. A 0 ~ A11 Address Row/column addresses are multiplexed on the same pins. Row address : RA0 ~ RA11, Column address : CA0 ~ CA7 BA0 ~ BA1 Bank select address Selects bank to be activated during row address latch time. Selects bank for read/write during column address latch time. RAS Row address strobe Latches row addresses on the positive going edge of the CLK with RAS low. Enables row access & precharge. CAS Column address strobe Latches column addresses on the positive going edge of the CLK with CAS low. Enables column access. WE Write enable Enables write operation and row precharge. Latches data in starting from CAS, WE active. L(U)DQM Data input/output mask Makes data output Hi-Z, tSHZ after the clock and masks the output. Blocks data input when L(U)DQM active. DQ0 ~ 15 Data input/output Data inputs/outputs are multiplexed on the same pins. V DD/VSS Power supply/ground Power and ground for the input buffers and the core logic. V DDQ/VSSQ Data output power/ground Isolated power supply and ground for the output buffers to provide improved noise immunity. N.C/RFU No connection /reserved for future use This pin is recommended to be left No Connection on the device. 57 S-102 TAS5142DKD (IC206: 1U-3811) 58 S-102 TAS5121DKD (IC207: 1U-3811) GND PWM_BP GND RESET DREG_RTN GVDD M3 DREG DGND M1 M2 DVDD SD DGND OTW GND PWM_AP GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 GVDD_B GVDD_B GND BST_B PVDD_B PVDD_B OUT_B OUT_B GND GND OUT_A OUT_A PVDD_A PVDD_A BST_A GND GVDD_A GVDD_A 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 Terminal Functions TERMINAL NAME DKD FUNCTION(1) DESCRIPTION BST_A 22 P High side bootstrap supply (BST), external resistor and capacitor to OUT_A required BST_B 33 P High side bootstrap supply (BST), external resistor and capacitor to OUT_B required DGND 9, 14 P I/O reference ground DREG 8 P Digital supply voltage regulator decoupling pin, 1 μFcapacitor connected to DREG_RTN DREG_RTN 5 P Decoupling return pin DVDD 12 P I/O reference supply input: 100 Ω to DREG, decoupled to GND, 0.1 μF capacitor connected to GND 1, 3, 16, 18, 21, 27, 28, 34 P Power ground, connected to system GND 6 P Local GVDD decoupling \pin GVDD_A 19, 20 P Gate drive input voltage GVDD_B 35, 36 P Gate drive input voltage M1 10 I Protection mode selection pin, connect to GND M2 11 I Protection mode selection pin, connect to DREG M3 7 I Output mode selection pin; connect to GND OTW 15 O Overtemperature warning output, open drain with internal pullup, active-low when temperature exceeds 115°C OUT_A 25, 26 O Output, half-bridge A OUT_B 29, 30 O Output, half-bridge B PVDD_A 23, 24 P Power supply input for half-bridge A PVDD_B 31, 32 P Power supply input for half-bridge B PWM_AP 17 I PWM input signal, half-bridge A PWM_BP 2 I PWM input signal, half-bridge B RESET 4 I Reset signal, active low GND GVDD SD 13 O (1) I = input, O = Output, P = Power Shutdown signal for half-bridges A and B (open drain with internal pullup) 59 S-102 BU2360FV (IC109: 1U-3836) BD7820 (IC111, IC707: 1U-3836) BLOCK DIAGRAM FIN 1 2 3 P in No. 4 5 1 2 3 4 5 FIN P in Nam e GND (FIN) Vr e f CTL Vcc N.C. OUT A DJ Driver GND TSD CTL (1PIN) 60 Vcc (2PIN) OCP N. C. (3PIN) OUT (4PIN) ADJ (5PIN) S-102 2. FL DISPLAY 15-BT-102GN 98 50 1 49 Pin Connection Grid Assignment Anode Connection 61 S-102 PRINTED WIRING BOARDS 1U-3836 MAIN P.W.B. UNIT (1/2) COMPONENT SIDE 62 S-102 1U-3836 MAIN P.W.B. UNIT (2/2) FOIL SIDE 63 S-102 1U-3831 LOC/PWR-DISP P.W.B. UNIT (1/2) COMPONENT SIDE 64 S-102 1U-3831 LOC/PWR-DISP P.W.B. UNIT (2/2) FOIL SIDE 65 S-102 1U-3811 D.AMP/SMPS P.W.B. UNIT (1/2) COMPONENT SIDE 66 S-102 1U-3811 D.AMP/SMPS P.W.B. UNIT (2/2) FOIL SIDE 67 S-102 1U-3807 FEP P.W.B. UNIT FOIL SIDE COMPONENT SIDE 68 S-102 NOTE FOR PARTS LIST 部品表について • • Parts for which "nsp" is indicated on this table cannot be supplied. When ordering of part, clearly indicate "1" and "I" (i) to avoid missupplying. • Ordering part without stating its part number can not be supplied. • Part indicated with the mark " ★ " is not illustrated in the exploded view. • Not including General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.) • Not including General-purpose Carbon Chip Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.) WARNING: Parts marked with this symbol ! have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 1.部品表に "nsp" と記載されている部品は供給できません。 2.部品を発注する際は特に数字の " 1 " と英字の "I" との区別をはっき り記入してください。 3.部品番号を表示していない部品は供給できません。 4. ! 印の部品は安全上重要な部品です。交換するときは、安全および性 能維持のため必ず指定の部品をご使用ください。 5.★印のついている部品は分解図中には記載していません。 6.汎用カーボン抵抗器は記載していません。定数は回路図を参照願いま す。 7.汎用カーボンチップ抵抗器は記載していません。定数は回路図を参照 願います。 8.部品表の抵抗器、コンデンサの品名記号の読み方は表を参照してくだ さい。 l Resistors Ex.: RN 14K 2E 182 G FR Type Shape Power Resist- Allowable Others and perance error formance RD RC RS RW RN RK : Carbon : Composition : Metal oxide film : Winding : Metal film : Metal mixture ] Resistance 1 8 2 ⇒ s s 2B 2E 2H 3A 3D 3F 3H : 1/8W : 1/4W : 1/2W : 1W : 2W : 3W : 5W F G J K M : ±1% : ±2% : ±5% : ±10% : ±20% P NL NB FR F RN RD RC RS RW RN RK : Pulse-resistant type : Low noise type : Non-burning type : Fuse-resistor : Lead wire forming 1800 ohm = 1.8 kohm Indicates number of zeros after effective number. 2-digit effective number. 14K : : : : : : 2E 2B 2E 2H 3A 3D 3F 3H ∗ 18 : : : : : : : 2 s R s ±1% ±2% ±5% ±10% ±20% F : G : J : K : M: 1800 G P NL NB FR F FR : : : : : =1.8k 0 2 ⇒ 2 W W W W W W W Ö • Units: ohm 1 1/8 1/4 1/2 1 2 3 5 182 1R 1.2 ohm 1-digit effective number. 2-digit effective number, decimal point indicated by R. 2 1.2 Ö 1 2 • Units: ohm R l Capacitors Ex.: CE 04W 1H 2R2 M BP Type Shape Dielectric Capacity Allowable Others and per- strength error formance CE : Aluminum foil electrolytic CA : Aluminum solid electrolytic CS : Tantalum electrolytic CQ : Film CK : Ceramic CC CP CM CF CH : Ceramic : Oil : Mica : Metallized : Metallized F : ±1% HS : High stability type 1A : 10V G : ±2% BP : Non-polar type 1C : 16V 1E : 25V 1V : 35V J : ±5% K : ±10% M : ±20% 1H 2A 2B 2C 2D 2E 2H 2J Z : +80% –20% P : +100% –0% C : ±0.25pF D : ±0.5pF = : Others HR : Ripple-resistant type DL : For change and discharge HF : For assuring high requency U : UL part C : CSA part W : UL-CSA type F : Lead wire forming 0J : 6.3V : 50V : 100V : 125V : 160V : 200V : 250V : 500V : 630V ] Capacity (electrolyte only) 2 2 2 ⇒ 2200μF s s Indicates number of zeros after effective number. 2-digit effective number. • Units: μF. 2 s R 2 s ⇒ CE CE CA CS CQ CK CC CP CM CF CH 04W : : : : : : : : : : 1H 6.3 10 16 25 35 50 100 125 160 200 250 500 2R2 0J 1A 1C 1E 1V 1H 2A 2B 2C 2D 2E 2H : : : : : : : : : : : : V V V V V V V V V V V V 2J : 630 V M ±1% ±2% ±5% ±10% ±20% +80% −20% P : +100% − 0% C : ±0.25pF D : ±0.5pF = : F G J K M Z : : : : : : BP HS BP HR DL HF U C W F : : : : : : : : : UL CSA UL-CSA ∗ 22 2 Ö 2R 2200μF 2 Ö 0 2 2.2μF 1-digit effective number. 2-digit effective number, decimal point indicated by R. 2.2μF 1 2 μF R μF • Units: μF. 22 ] Capacity (except electrolyte) 2 s 2 2 s 2 Ö ⇒ 2200pF=0.0022μF (More than 2) Indicates number of zeros after effective number. 2-digit effective number. s 2 1 s 22 1 Ö 220pF (0 0 0 (0 2 ) 2 • Units: pF. 2 2200pF=0.0022μF pF ⇒ 220pF (0 or 1) Indicates number of zeros after effective number. 2-digit effective number. 2 pF AC • Units: pF. • When the dielectric strength is indicated in AC, "AC" is included after the dieelectric strength value. 69 0 1 ) S-102 PARTS LIST OF P.W.B. UNIT * 本表に "nsp" と記載されている部品は供給できません。 * Parts for which "nsp" is indicated on this table cannot be supplied. * 本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model JP : Japan model 1U-3836D/E/F MAIN P.W.B. UNIT ASS’Y Ref. No. Part No. Part Name Remarks SEMICONDUCTORS GROUP IC101 00D 262 3708 004 IC102 00D GEN 8571 -0 ES6178FF B/E ROM SUB ASSY IC103 00D 262 3759 008 K4S641632K-UC60 IC104 00D 262 3402 902 BR24L32F-WE2 +C IC105 00D 262 3242 900 SN74LV273APW-EL2 IC108 00D 262 2516 909 SN74LV32APW-EL2 +C IC109 00D 262 3751 909 BU2360FV-FE2 IC110 00D 262 3046 902 TC7WH157FU IC111 00D 263 1282 907 BD7820FP-E2 IC202 00D 262 3707 908 BR25L640F-WE2 IC203 00D 262 3082 924 BD4730G-TR IC205 00D 262 2953 902 SN74HCT244APW IC210 00D 262 2813 903 SN74AHCT08PW-EL2 IC211 00D 262 2517 908 SN74LV08APW-EL2 ES29LV160EB-70TGI +REF +C +C +C +REF IC301 00D GEN 8570 -0 SYSTEM ROM SUB ASSY IC303 00D 263 1240 907 BA33B00FP-E2 IC304 00D 263 1278 908 SI-8001FDE IC305 00D 263 1279 907 SI-8008TM IC306 00D 263 1278 908 SI-8001FDE IC401 00D 262 3709 003 ADSP21367KSZ1A1138 IC402 00D 262 3746 008 W9864G2GH-7 IC403 00D GEN 8630 -0 DSP ROM ASSY IC404 00D 263 1281 908 BD9130NV-E2 IC501 00D 262 3757 000 ADAU1328BSTZ1138 ES29LV160EB-70TGI IC502 00D 262 3449 004 LC89057W-VF4A IC503 00D 262 3750 007 LC4064V-75TN100C(S302) IC504,505 00D 263 0934 900 BA4510F-E2 IC506,507 00D 263 0896 909 NJM2068MD-TE1 IC508 00D 262 2977 946 BA33BC0FP-E2 IC511 00D 269 0231 009 GP1FAV31RK0F IC601 00D 263 1245 009 M61531FP IC602 00D 263 1232 902 NJM79L07UA-TE1 IC603 00D 263 1231 903 NJM78L07UA-TE1 IC604 00D 263 0615 902 BA15218F-DXE2 IC608 00D 263 0995 004 NJM4556AD IC609,610 00D 263 0615 902 BA15218F-DXE2 M30627FHPGP +C +C +REF +C +T +C IC611-613 00D 263 1277 909 RC4580IDR IC701 00D 262 3577 002 FLI2310-LF-CF IC702 00D 262 3303 001 K4S643232H-UC60 IC703 00D 262 3752 005 XC2C128-7TQG144C-VSW1 IC704 00D 262 3364 011 SII9030CTU-7 IC706 00D 263 1296 906 TA48025BF(T6L1,NQ) IC707 00D 263 1282 907 BD7820FP-E2 IC708 00D 263 1295 907 TA48018BF(T6L1,NQ) IC801 00D 262 3478 004 ADV7320 IC802 00D 262 3365 900 BH7868FS IC803 00D 262 3277 904 SN74LVC157APW-EL2 +REF +C 70 Q'ty New S-102 Ref. No. Part No. Part Name IC804,805 00D 262 3446 900 TC4052BFT IC806,807 00D 263 1296 906 TA48025BF(T6L1,NQ) IC901 00D 262 3360 905 LC72722PM-TLM TR201 00D 274 0188 905 2SD1858TV2(Q/R) Remarks for E2 TR202 00D 269 0184 907 KRA102S-RTK/P (10K-10K) TR203,204 00D 269 0192 902 KRC102S-RTK/P (10K-10K) TR211,212 00D 273 0488 000 2SC4614 (HFE S/T) TR301-307 00D 269 0192 902 KRC102S-RTK/P (10K-10K) TR501-503 00D 273 0460 905 KTC2875-B-RTK/P TR504 00D 269 0192 902 KRC102S-RTK/P (10K-10K) TR505 00D 269 0184 907 KRA102S-RTK/P (10K-10K) TR601-604 00D 273 0460 905 KTC2875-B-RTK/P TR607 00D 269 0184 907 KRA102S-RTK/P (10K-10K) TR608 00D 269 0192 902 KRC102S-RTK/P (10K-10K) TR609 00D 273 0384 900 2SC2412KT96(S) TR610,611 00D 269 0184 907 KRA102S-RTK/P (10K-10K) +C TR612 00D 269 0192 902 KRC102S-RTK/P (10K-10K) TR613-615 00D 273 0460 905 KTC2875-B-RTK/P TR616 00D 269 0192 902 KRC102S-RTK/P (10K-10K) TR701 00D 275 0110 905 HN1K02FU-TE85L TR801-805 00D 271 0293 901 2SA1022-B TR810 00D 273 0384 900 2SC2412KT96(S) TR901,902 00D 273 0486 905 KRC231S-RTK(2.2K) TR903 00D 269 0192 902 KRC102S-RTK/P (10K-10K) TR904 00D 269 0184 907 KRA102S-RTK/P (10K-10K) TR905 00D 269 0192 902 KRC102S-RTK/P (10K-10K) TR906 00D 271 0331 902 2SA2092QTL TR907 00D 269 0184 907 KRA102S-RTK/P (10K-10K) TR908 00D 269 0192 902 KRC102S-RTK/P (10K-10K) TR909 00D 273 0464 901 KTC3875S-GR-RTK/P D101 00D 276 0794 900 KDS160-RTK/P D201,202 00D 276 0794 900 KDS160-RTK/P D203 00D 276 0717 903 1SS355 TE-17 D210-213 00D 276 0401 905 1SS133T77 (TAPE) D214,215 00D 276 0794 900 KDS160-RTK/P D301 00D 276 0825 905 SFPB-74V D302 00D 276 0824 906 SFPB-64V D303 00D 276 0825 905 SFPB-74V D307-310 00D 276 0750 902 RB521S-30TE61 +C +C for E2 +C +REF D401 00D 276 0750 902 RB521S-30TE61 +REF D501,502 00D 276 0750 902 RB521S-30TE61 +REF D601,602 00D 276 0750 902 RB521S-30TE61 +REF D604,605 00D 276 0750 902 RB521S-30TE61 +REF D610 00D 276 0560 901 DAN202KT146 +C D613 00D 276 0560 901 DAN202KT146 +C D614 00D 276 0559 909 DAP202KT146 +C D701-703 00D 276 0794 900 KDS160-RTK/P D704-711 00D 276 0833 900 ESD PROTECTOR(6802) D801,802 00D 276 0794 900 KDS160-RTK/P D901,902 00D 276 0794 900 KDS160-RTK/P ZD201 00D 276 0683 914 UDZS9.1B-TE17 ZD205 00D 276 0760 989 MTZJ7.5B T77 ZD701 00D 276 0683 930 UDZS5.1B-TE17 +C +C 71 Q'ty New S-102 Ref. No. Part No. Part Name RESISTORS GROUP R452,453 00D 241 2313 901 RD14B2E101GFRST R845 00D 244 2051 974 RS14B3A102JNBST(S) VR801-805 00D 211 6148 906 V03PB471MT(RH03ADCS) +REF 00D 257 2018 900 CS77B1A100MT(NOJ) CAPACITORS GROUP C101,102 C103-105 nsp CK73F1C104ZT +1005 C107 nsp CK73F1H103ZT +1005 C108 nsp CK73F1C104ZT +1005 C110 00D 254 4739 916 C111 nsp C112 00D 254 4739 916 C113-121 C122 nsp 00D 254 4739 916 CE67W1A470MT(GV) CK73F1C104ZT +1005 CE67W1A470MT(GV) CK73F1C104ZT +1005 CE67W1A470MT(GV) C123-133 nsp CK73F1C104ZT +1005 C134 nsp CK73F1E104ZT +1608 C137 00D 254 4739 916 CE67W1A470MT(GV) C138 nsp CK73B1H102KT +1005 C139 nsp CK73F1C104ZT +1005 C140 nsp CK73F1H103ZT +1005 C141 00D 254 4739 916 CE67W1A470MT(GV) C142-148 nsp CK73F1C104ZT +1005 C149 nsp CK73F1H103ZT +1608 C150 nsp CK73F1E104ZT +1608 C151 nsp CK73B1H102KT +1608 C153 nsp CK73F1E104ZT +1608 C154 00D 254 4739 916 C155 nsp CC73CH1H6R0DT C156 nsp CK73F1E104ZT C157 nsp CC73CH1H6R0DT C158 nsp CK73F1H103ZT +1608 C159 nsp CK73F1E104ZT +1608 CE67W1A470MT(GV) +1608 +1608 +1608 C160 nsp CK73B1H102KT +1608 C161 nsp CK73F1H103ZT +1608 C162 nsp CK73F1E104ZT +1608 C163 nsp CK73B1H102KT +1608 C166 nsp CK73F1E104ZT +1608 C167 nsp CK73B1H102KT +1608 C170 00D 254 4739 916 C171,172 nsp CE67W1A470MT(GV) CK73F1E104ZT +1608 C173 00D 254 4739 916 CE67W1A470MT(GV) C180 nsp CK73F1E104ZT +1608 C192 nsp CK73F1E104ZT +1608 C193 nsp CK73B1H102KT +1608 C194,195 nsp CK73F1E104ZT +1608 C221 00D 254 4740 976 CE67W1C100MT(GV) C222 nsp CK73F1E104ZT C223 nsp CK73B1H102KT +1608 C224 nsp CK73F1E104ZT +1608 C226 nsp CK73F1E104ZT +1608 C241-244 nsp CK73F1E104ZT +1608 C245 nsp CK73B1H102KT +1608 C247 nsp CK73F1E104ZT +1608 +1608 72 Remarks Q'ty New S-102 Ref. No. Part No. Part Name C260 nsp CK73F1E104ZT +1608 C276 nsp CK73F1E104ZT +1608 C277 nsp CK73B1H102KT +1608 C278 00D 254 4740 934 C279 nsp C281 nsp C282 00D 254 4756 902 CE67W1C101MT(GV) CK73F1E104ZT +1608 CK73F1H103ZT +1608 CE04W1H101MT HB5(KY) C283 nsp CK73F1E104ZT +1608 C284,285 nsp CK73F1H473ZT +1608 C286 00D 255 1278 907 CQ93M2D562JT(B) C287 00D 254 4713 916 CE04W1E470MT E11(KY) C293 00D 254 4740 976 CE67W1C100MT(GV) C294 nsp CK73F1E104ZT C298 nsp CK73F1H103ZT +1608 C301 nsp CK73F1E104ZT +1608 C302 nsp CK73F1H103ZT +1608 C303 nsp CK73F1E104ZT +1608 C304 00D 254 4740 921 C305 nsp CK73F1E104ZT +1608 C306 nsp CK73B1H102KT +1608 C307 00D 254 4740 921 C308 nsp CK73F1E104ZT +1608 C310 nsp CK73F1C104ZT +1005 C326 00D 254 4739 916 C327 nsp C328 00D 254 4739 916 C329,330 nsp +1608 CE67W1C470MT(GV) CE67W1C470MT(GV) CE67W1A470MT(GV) CK73F1H103ZT +1608 CE67W1A470MT(GV) CK73F1H103ZT +1608 C331 00D 254 4740 921 CE67W1C470MT(GV) C361 00D 254 4709 700 CE04W1V221MC JC5(KY) C362 00D 257 1020 915 CK73B1H225KT C363 nsp C365 nsp C366 00D 254 4711 905 C367 00D 254 4709 700 CE04W1V221MC JC5(KY) C368 00D 257 1020 915 CK73B1H225KT CK73B1H103KT (1608) +1608 CK73F1E104ZT +1608 CE04W1A471MT HB5(KY) C369 nsp CK73B1E104KT +1608 C371 nsp CK73F1E104ZT +1608 C372 00D 254 4711 905 C373 00D 254 4709 700 CE04W1A471MT HB5(KY) CE04W1V221MC JC5(KY) C374 00D 257 1020 915 CK73B1H225KT C375 nsp CK73B1E104KT +1608 CK73F1E104ZT +1608 C377 nsp C378 00D 254 4712 904 C379 nsp CK73F1E104ZT +1608 C380 nsp CK73B1H102KT +1608 C401 nsp CK73F1C104ZT +1005 C402-409 nsp CK73F1H103ZT +1005 C410-415 nsp CC73CH1H101JT C416-420 nsp CK73B1H102KT +1005 C421 00D 257 2018 900 CS77B1A100MT(NOJ) C422 nsp CC73CH1H101JT C423 nsp CK73F1H103ZT C424 nsp CK73B1H102KT +1005 C425,426 nsp CE04W1C471MT JC5(KY) CK73F1C104ZT +1005 +1005 +1005 +1005 C427 00D 257 2018 900 CS77B1A100MT(NOJ) C428 nsp CK73B1H102KT +1005 73 Remarks Q'ty New S-102 Ref. No. C429 Part No. nsp Part Name CK73F1C104ZT +1005 C430 nsp CK73B1H102KT +1005 C431 nsp CK73F1C104ZT C432 00D 257 0039 910 CK73B0J226MT C433 nsp CK73B1H102KT C434 nsp CK73B1A106KT +2125 C435 nsp CK73F1C104ZT +1005 C436-446 nsp CK73F1H103ZT +1005 C447,448 nsp CK73F1C104ZT +1005 C449,450 nsp CC73CH1H8R0DT C451,452 nsp CK73F1C104ZT C453,454 00D 257 2018 900 +1005 +1608 +1608 +1005 CS77B1A100MT(NOJ) C501 nsp CK73F1E104ZT C502 nsp CK73B1H102KT +1608 C503 nsp CK73B1E223KT +1608 C504 00D 254 4740 921 C505 nsp CK73F1E104ZT C506,507 nsp CK73F1H103ZT +1608 C508 nsp CK73F1E104ZT +1608 C509 00D 254 4740 976 CE67W1C100MT(GV) C510 00D 254 4742 916 CE67W1V100MT(GV) C511,512 C513 C514,515 nsp 00D 254 4740 976 nsp +1608 CE67W1C470MT(GV) CK73F1E104ZT +1608 +1608 CE67W1C100MT(GV) CK73F1H103ZT +1608 C517 00D 254 4740 921 CE67W1C470MT(GV) C518 nsp CK73F1E104ZT +1608 C520 nsp CK73B1H562KT +1608 C521 nsp CC73CH1H391JT C523 00D 254 4740 921 C524 nsp CK73F1H103ZT +1608 C525 nsp CK73F1E104ZT +1608 +1608 CE67W1C470MT(GV) C526 nsp CK73B1H102KT +1005 C527 nsp CK73F1E104ZT C528 nsp C529 00D 254 4740 976 +1608 CC73CH1H121JT +1608 CE67W1C100MT(GV) C530 nsp C531 00D 254 4740 921 C532 nsp CC73CH1H101JT C533 nsp CK73B1H102KT +1005 C534 nsp CK73F1E104ZT C535 nsp CC73CH1H121JT C536 00D 254 4740 976 C537 nsp C538 00D 254 4740 921 C539 nsp C541,542 C543 nsp 00D 254 4742 916 CC73CH1H101JT +1608 CE67W1C470MT(GV) +1608 +1608 +1608 CE67W1C100MT(GV) CC73CH1H101JT +1608 CE67W1C470MT(GV) CC73CH1H101JT +1608 CC73CH1E681JT +1608 CE67W1V100MT(GV) C544 nsp CK73B1H332KT +1608 C545,546 nsp CK73F1E104ZT +1608 C547,548 00D 254 4740 934 C550,551 nsp CE67W1C101MT(GV) CC73CH1E681JT +1608 C552 00D 254 4742 916 C553 nsp CK73B1H332KT +1608 C554 nsp CK73F1E104ZT +1608 C556,557 nsp CC73CH1E681JT C558 00D 254 4742 916 CE67W1V100MT(GV) +1608 CE67W1V100MT(GV) 74 Remarks Q'ty New S-102 Ref. No. Part No. Part Name C559 nsp CK73B1H332KT +1608 C560 nsp CK73F1E104ZT +1608 C561 nsp CK73F1H103ZT +1608 C563 00D 254 4743 902 CE67W1H0R1MT(GV) C564 00D 254 4740 921 CE67W1C470MT(GV) C565 nsp CK73F1E104ZT C566 nsp CK73B1H102KT +1608 C567,568 nsp CK73F1E104ZT +1608 C569 C570,571 00D 256 1058 971 nsp +1608 CF93A1H104JT (JL) CK73F1E104ZT +1608 C572 00D 255 1265 978 CQ93M1H223JT(B) C573 nsp CC73CH1H100DT +1608 C574 nsp CC73CH1H120JT +1608 C575 nsp CK73B1H102KT +1608 C576 nsp CK73F1E104ZT +1608 C577 nsp CK73F1H103ZT +1608 C578 nsp CK73F1E104ZT +1608 C579 nsp CK73F1H103ZT +1608 C583 nsp CK73F1E104ZT +1608 C584 nsp CC73CH1H220JT C601 nsp CK73B1H102KT C602 nsp CK73F1H103ZT +1608 C603 nsp CK73F1E104ZT +1608 C604 00D 254 4740 921 C605-613 nsp C702,703 00D 254 4742 916 C704,705 nsp +1608 +1608 CE67W1C470MT(GV) CK73F1E104ZT +1608 CE67W1V100MT(GV) CK73B1E473KT +1608 C706 00D 254 4740 934 CE67W1C101MT(GV) C707 nsp C708 00D 254 4740 921 C709 nsp C710 00D 254 4742 916 C711 nsp CK73F1H103ZT +1608 C712 nsp CK73F1E104ZT +1608 C714 nsp CK73B1H222KT +1608 C715 nsp CK73B1E473KT +1608 C716,717 nsp CK73B1A224KT +1608 C718 nsp CK73B1E473KT +1608 C719 nsp CK73B1H222KT +1608 CK73F1H103ZT +1608 CE67W1C470MT(GV) CK73F1H103ZT +1608 CE67W1V100MT(GV) C724,725 00D 254 4742 903 CE67W1V4R7MT(GV) C726 00D 254 4740 921 CE67W1C470MT(GV) C727,728 nsp CK73F1H103ZT +1608 C729 nsp CK73F1E104ZT +1608 C734-739 00D 254 4742 916 C740 nsp C741 00D 254 4740 934 CE67W1V100MT(GV) CK73F1E104ZT +1608 CE67W1C101MT(GV) C742,743 nsp CC73CH1H101JT C744 nsp CK73F1E104ZT C745 00D 254 4740 934 +1608 +1608 CE67W1C101MT(GV) C746 nsp C747 00D 254 4740 947 CE67W1C221MT(GV) CK73F1H103ZT +1608 C749 00D 254 4742 916 CE67W1V100MT(GV) C751 nsp C752 00D 254 4740 976 CC73CH1H101JT +1608 CE67W1C100MT(GV) C753,754 nsp CK73F1E104ZT +1608 C755 nsp CK73B1H102KT +1608 75 Remarks Q'ty New S-102 Ref. No. C758 Part No. 00D 254 4742 929 C759 nsp C760 00D 254 4742 916 C762 nsp C763 00D 254 4742 929 Part Name CE67W1V220MT(GV) CK73F1E104ZT +1608 CE67W1V100MT(GV) CC73CH1H470JT +1608 CE67W1V220MT(GV) C764 nsp C765 00D 254 4742 916 CE67W1V100MT(GV) C767 00D 254 4742 916 CE67W1V100MT(GV) C769 nsp C770 00D 254 4740 976 C771 nsp C774 00D 254 4742 929 C775 nsp C777 nsp C778 00D 254 4742 929 C779 nsp C781 00D 254 4742 916 C783 nsp C784 00D 254 4740 976 C785,786 nsp CK73F1E104ZT +1608 CC73CH1H101JT +1608 CE67W1C100MT(GV) CK73F1H103ZT +1608 CE67W1V220MT(GV) CK73F1E104ZT +1608 CC73CH1H470JT +1608 CE67W1V220MT(GV) CK73F1E104ZT +1608 CE67W1V100MT(GV) CK73B1H152KT +1608 CE67W1C100MT(GV) CK73F1E104ZT C790 00D 254 4742 929 C791 nsp CK73F1E104ZT C793 nsp CC73CH1H470JT C794 00D 254 4742 929 C795 nsp C796 00D 254 4742 916 C798 nsp CC73CH1H470JT C799 nsp CK73F1E104ZT C800 00D 254 4742 916 C802 nsp CC73CH1H470JT C803 nsp CK73F1E104ZT +1608 CE67W1V220MT(GV) +1608 +1608 CE67W1V220MT(GV) CK73F1E104ZT +1608 CE67W1V100MT(GV) +1608 +1608 CE67W1V100MT(GV) C841-844 nsp CC73CH1H221JT C851,852 nsp CK73F1C104ZT +1608 +1608 +1608 +1005 C853 00D 257 2018 900 C854 nsp CS77B1A100MT(NOJ) CK73F1C104ZT C855 nsp CK73F1H103ZT +1005 C856-858 nsp CK73F1C104ZT +1005 +1005 C859 00D 257 2018 900 C860 nsp CS77B1A100MT(NOJ) CK73F1C104ZT +1005 C861 nsp CK73F1H103ZT +1608 C862 nsp CK73B1H102KT +1005 C863 nsp CK73F1H103ZT +1005 C864-867 nsp CK73F1C104ZT +1005 C868 nsp CK73B1H102KT +1005 C869 nsp CK73F1C104ZT C870 nsp CK73B1H102KT +1005 C871 nsp CK73B1H102KT +1608 C872 nsp CK73F1E104ZT +1608 C901 nsp CK73F1H103ZT +1005 +1005 C902-905 nsp CK73F1C104ZT +1005 C906 nsp CK73F1H103ZT +1005 C907 00D 257 2018 900 CS77B1A100MT(NOJ) C908,909 nsp CK73F1C104ZT +1005 C910 nsp CK73F1H103ZT +1005 C911 nsp CK73F1C104ZT +1005 C912 00D 257 2018 900 CS77B1A100MT(NOJ) 76 Remarks Q'ty New S-102 Ref. No. Part No. Part Name C913-928 nsp CK73F1C104ZT +1005 C929 nsp CK73F1H103ZT +1005 C930 nsp CK73B1H102KT +1005 C931 nsp CK73F1H103ZT +1005 C932 nsp CK73F1C104ZT +1005 C933,934 nsp CC73CH1H180JT C935 nsp CK73F1H103ZT C936 00D 257 2018 900 C937-948 nsp +1608 +1005 CS77B1A100MT(NOJ) CK73F1C104ZT +1005 C949 nsp CK73B1H102KT +1005 C950,951 nsp CK73F1C104ZT C952,953 00D 257 5003 983 C954 nsp +1005 CC73CH1H470JT CK73F1C104ZT +1005 C955 nsp CK73B1H102KT +1005 C956 nsp CK73F1C104ZT C957 nsp CK73B1H102KT +1005 C958 00D 257 2018 900 CS77B1A100MT(NOJ) C959,960 C961 +1005 nsp CK73B1H102KT +1005 00D 257 2018 900 CS77B1A100MT(NOJ) C962,963 nsp CK73F1C104ZT C965 nsp CK73B1H102KT +1005 +1005 C966 00D 257 2018 900 CS77B1A100MT(NOJ) C967 nsp CK73B1H102KT +1005 C968-970 nsp CK73F1C104ZT +1005 C972 nsp CK73F1C104ZT +1005 C974-977 nsp CK73B1E104KT +1608 C978 nsp CK73F1C104ZT +1005 C979 nsp CK73F1H103ZT +1005 C980,981 nsp CK73B1H102KT +1005 00D 257 2018 900 CS77B1A100MT(NOJ) C982 C983,984 nsp CK73F1C104ZT +1005 C985 00D 257 2018 900 CS77B1A100MT(NOJ) C986 nsp CK73F1C104ZT +1005 C987 nsp CK73F1H103ZT +1005 C988 nsp CK73B1H102KT +1005 C989 nsp C990 00D 257 2018 900 CK73F1H103ZT +1608 C991 nsp CK73F1H103ZT +1608 C992 nsp CK73F1E104ZT +1608 CK73B1H102KT +1608 CS77B1A100MT(NOJ) C993 nsp C994 00D 257 2018 900 CS77B1A100MT(NOJ) C996 00D 257 2018 900 CS77B1A100MT(NOJ) C997 nsp CK73F1C104ZT +1005 C998 nsp CK73F1E104ZT +1608 CC101,102 00D 257 2018 900 CC103-105 nsp CS77B1A100MT(NOJ) CK73F1C104ZT CC106 nsp CK73B1H102KT +1005 CC107 nsp CK73F1H103ZT +1005 CC108,109 nsp CK73F1E104ZT +1608 CC113 nsp CK73F1C104ZT +1005 CC114 nsp CK73B1H821KT +1608 CC115 00D 257 2018 900 CC116 nsp CK73F1C104ZT CC117 nsp CK73B1H392KT +1608 CC118 nsp CK73F1C104ZT +1005 +1005 CS77B1A100MT(NOJ) +1005 77 Remarks Q'ty New S-102 Ref. No. Part No. Part Name CC119,120 nsp CK73B1H102KT +1005 CC121 nsp CK73F1C104ZT CC122 nsp CK73B1H102KT +1005 CC123,124 nsp CK73F1C104ZT +1005 CC125-129 nsp CK73F1E104ZT +1608 CC139,140 nsp CK73F1E104ZT +1608 CC141,142 00D 254 4740 921 CC143,144 nsp CK73F1E104ZT +1608 CC145 nsp CK73B1E104KT +1608 +1005 CE67W1C470MT(GV) CC146-150 00D 254 4740 976 CE67W1C100MT(GV) CC151 00D 254 4740 934 CE67W1C101MT(GV) CC152 nsp CC153 00D 254 4740 905 CC154 nsp CK73F1E104ZT +1608 CC155-160 nsp CK73B1E104KT CK73F1E104ZT +1608 +1608 CE67W1C220MT(GV) CC161 00D 254 4738 946 CE67W0J102MT(GV) CC162 00D 254 4740 905 CE67W1C220MT(GV) CC163 00D 254 4738 946 CE67W0J102MT(GV) CC164 00D 254 4740 905 CE67W1C220MT(GV) CC165 00D 254 4738 946 CE67W0J102MT(GV) CC166 00D 254 4740 905 CE67W1C220MT(GV) CC167 00D 254 4740 934 CE67W1C101MT(GV) CC168 00D 254 4740 905 CE67W1C220MT(GV) CC169 00D 254 4740 934 CE67W1C101MT(GV) CC170 00D 254 4740 905 CE67W1C220MT(GV) CC177 00D 254 4740 934 CE67W1C101MT(GV) CC178 nsp CK73F1E104ZT +1608 CC179 nsp CK73F1H103ZT +1608 CC180 00D 254 4740 934 CE67W1C101MT(GV) CC181 nsp CK73F1E104ZT CC182,183 nsp CK73F1H103ZT +1608 CC184,185 nsp CK73F1E104ZT +1608 CC186 nsp CK73F1H103ZT +1608 +1608 CC187 nsp CK73B1H102KT +1608 CC188,189 nsp CK73F1E104ZT +1608 CC190 00D 254 4740 976 CE67W1C100MT(GV) CC191 00D 257 2018 900 CS77B1A100MT(NOJ) CC193,194 00D 257 2018 900 CS77B1A100MT(NOJ) CC195 nsp CC196 00D 254 4743 986 CE67W1H100MT(GV) CC197,198 00D 254 4740 976 CE67W1C100MT(GV) CC199,200 CC201 nsp 00D 254 4740 976 CK73B1H102KT CK73F1E104ZT +1608 +1608 CE67W1C100MT(GV) CC301-304 nsp CK73F1H103ZT +1608 CC305,306 nsp CK73F1E104ZT +1608 CC307 00D 254 4740 976 CC308 nsp CC309,310 CC311 00D 254 4740 976 nsp Remarks CE67W1C100MT(GV) CK73F1H103ZT +1608 CE67W1C100MT(GV) CC73CH1H561JT CK73F1H103ZT for E2 for E2 +1608 +1608 for E2 CC312 nsp CC313 00D 254 4739 916 CC314 nsp CC73CH1H220JT +1608 for E2 CC315 nsp CC73CH1H180JT +1608 for E2 CC316 nsp CK73F1H103ZT CC317 nsp CC73CH1H331JT CC318 nsp CK73F1H103ZT CE67W1A470MT(GV) for E2 for E2 +1608 +1608 +1608 78 for E2 for E2 Q'ty New S-102 Ref. No. Part No. Part Name CC321 nsp CC73CH1H101JT CC324 nsp CC73CH1H101JT CC325 nsp CK73F1E104ZT +1608 CC326 nsp CK73F1H103ZT +1608 CC327 nsp CK73B1E104KT +1608 CC328 nsp CK73B1H103KT (1608) +1608 CC329 nsp CC330 00D 254 4740 976 CC331 nsp CK73B1H102KT +1608 CC332,333 nsp CK73F1E104ZT +1608 CC334,335 nsp CK73B1H102KT +1608 CC336 nsp CK73F1E104ZT +1608 CC337 nsp CK73F1H103ZT +1608 CK73F1E104ZT +1608 CC338 nsp CC339 00D 254 4740 976 CK73B1E104KT +1608 +1608 +1608 CE67W1C100MT(GV) CE67W1C100MT(GV) CC340 nsp CK73B1E104KT +1608 CC341 nsp CK73F1H103ZT +1608 CC342 nsp CK73B1H102KT +1608 CC343 nsp CK73F1E104ZT +1608 CC901 nsp CK73F1E104ZT +1608 CC902 nsp CK73F1H103ZT +1608 CC903 nsp CK73B1H102KT +1608 CC904 nsp CK73F1E104ZT +1608 CC905 nsp CK73F1H103ZT +1608 CC906 nsp CK73B1H102KT +1608 CC907 nsp CK73F1E104ZT +1608 CC908 nsp CK73F1H103ZT +1608 CC909 nsp CK73B1H102KT +1608 CC910 nsp CK73F1E104ZT +1608 CC911 nsp CK73F1H103ZT +1608 CC912 nsp CK73B1H102KT +1608 CC913 nsp CK73F1E104ZT +1608 CC914 nsp CK73F1H103ZT +1608 CC915 nsp CK73B1H102KT +1608 CC916 nsp CK73F1E104ZT +1608 CC917 nsp CK73F1H103ZT +1608 CC918 nsp CK73B1H102KT +1608 CC919 nsp CK73F1E104ZT +1608 CC920 nsp CK73F1H103ZT +1608 CC921 nsp CK73B1H102KT +1608 CC922 nsp CK73F1E104ZT +1608 CC923 nsp CK73F1H103ZT +1608 CC924 nsp CK73B1H102KT +1608 CC925 nsp CK73F1E104ZT +1608 CC926 nsp CK73F1H103ZT +1608 CC927 nsp CK73B1H102KT +1608 CC928 nsp CK73F1E104ZT +1608 CC929 nsp CK73F1H103ZT +1608 CC930 nsp CK73B1H102KT +1608 CC931 nsp CK73F1E104ZT +1608 CC932 nsp CK73F1H103ZT +1608 CC933 nsp CK73B1H102KT +1608 CC934 nsp CK73F1E104ZT +1608 CC935 nsp CK73F1H103ZT +1608 CC936 nsp CK73B1H102KT +1608 CC937 nsp CK73F1E104ZT +1608 79 Remarks Q'ty New S-102 Ref. No. Part No. Part Name CC938 nsp CK73B1H102KT +1608 CC939 nsp CK73F1E104ZT +1608 CC940 nsp CK73F1H103ZT +1608 CC941 nsp CK73B1H102KT +1608 CC942 nsp CK73F1E104ZT +1608 CC943 nsp CK73F1H103ZT +1608 CC944 nsp CK73B1H102KT +1608 CC945 nsp CK73F1E104ZT +1608 CC946 nsp CK73F1H103ZT +1608 CC947 nsp CK73B1H102KT +1608 CC948 nsp CK73F1E104ZT +1608 CC949 nsp CK73F1H103ZT +1608 CC950 nsp CK73B1H102KT +1608 CC951 nsp CK73F1H103ZT +1608 CC952 nsp CK73B1H102KT +1608 CC954 nsp CK73F1E104ZT +1608 CC955 nsp CK73F1H103ZT +1608 CC956 nsp CK73B1H102KT +1608 CC957 nsp CK73F1E104ZT +1608 CC958 nsp CK73F1H103ZT +1608 CC959-965 nsp CK73B1H102KT +1608 CC966 nsp CK73F1E104ZT +1608 CC967 nsp CK73F1H103ZT +1608 CC968 nsp CK73B1H102KT +1608 CC969-990 nsp CK73F1H103ZT +1608 CC991 nsp CK73B1H102KT +1608 CC992 nsp CK73F1H103ZT +1608 CX031 nsp 3P PH CON.BASE(TAPE) +REF CX051 nsp 5P PH CON BASE(TAPE) +REF CX052 00D 205 1154 958 CX061 nsp 6P PH CON.BASE CX142 nsp 14P PIN HEADER(9120) CX151 00D 205 0736 076 15P FFC CON.BASE CX171 00D 205 1343 989 17P FFC BASE(9610SC) CX211 00D 205 1343 947 21P FFC BASE(9610SC) CX301 00D 205 1401 902 30P-FFC-BASE(9610SC) CY021 nsp 2P VH CON BASE (White) OTHERS PARTS GROUP 5P ZH-ZR CON.BASE-T +REF FB101 00D 235 0136 907 FBMJ1608HS280NT FB201,202 00D 235 0130 903 CHIP EMIFIL(11A121) +1608 FB501 00D 235 0130 903 CHIP EMIFIL(11A121) +1608 FB701,702 00D 235 0136 907 FBMJ1608HS280NT +1608 FB801 00D 235 0136 907 FBMJ1608HS280NT +1608 FB901 00D 235 0147 909 E.FIL(BLM21PG221SN1)+2125 JK201 00D 204 8637 006 MINI JACK (STEREO) JK301 00D 204 8713 001 2P/S-TERM(SYK22) +1608 JK601 00D 204 8748 005 4P PIN JACK(FGND NI) JK701 00D 204 8719 005 19P HDMI CONNECTOR JK702 00D 204 8746 007 3P PIN JACK(FG GBR) JK801 00D 204 8711 003 1P/S-TERM(SYK22) 80 Remarks Q'ty New S-102 Ref. No. Part No. Part Name L201 00D 235 0166 003 INDUCTOR 100UH(7208M L301 00D 235 0186 902 INDUCTOR 47UH(7B12N) L302 00D 235 0185 903 INDUCTOR 47UH(7E10H) L303 00D 235 0186 902 INDUCTOR 47UH(7B12N) L401 00D 235 0183 905 INDUCTOR 2.2UH(7E06N L702-704 00D 235 0125 905 INDUCTOR(FLC32C220K)+3216 L803,804 00D 235 0125 905 INDUCTOR(FLC32C220K)+3216 S201 00D 279 0051 008 NTSA0WB203EE1B0 S202 00D 212 1204 000 SLIDE SW(SSAA110500) ST101-103 nsp STYLE PIN ST105,106 nsp STYLE PIN T201 W201,202 00D 231 8087 001 D/D TRANS(060478026) nsp M3 SCREW TERMINAL X101 00D 399 0619 906 XTAL(27MHZ) X301 00D 399 0887 903 CSTCE16MOV53-R0 X401 00D 399 1113 906 X-TAL(L5030-16.660) X501 00D 399 1116 903 X-TAL(S-24.576) X701 00D 399 0864 900 XTAL(13.5MHZ) X901 00D 399 1009 007 X-TAL(S-4.332-14) Remarks +REF +2125 +REF for E2 81 Q'ty New S-102 1U-3831D LOC/PWR-DSP P.W.B. UNIT ASS'Y Ref. No. Part No. Part Name SEMICONDUCTORS GROUP IC102 00D 263 1259 008 BA12T IC103 00D 263 1260 000 KIA79M12PI-U/P IC104 00D 263 1227 001 BA50BC0T IC105 00D 263 1268 002 KIA79M05PI-U/P IC106 00D 263 1269 904 BA178M18CP-E2 IC107 00D 265 0130 001 STR-G7421(LF1129) IC108 00D 263 1155 005 SE-B2(LF12) IC241 00D 262 3228 005 M66005-0001AHP IC242 00D 262 3602 003 GP1UE271XKVF TR101 00D 269 0184 907 KRA102S-RTK/P (10K-10K) TR102 00D 269 0192 902 KRC102S-RTK/P (10K-10K) TR103 00D 273 0464 901 KTC3875S-GR-RTK/P TR205-207 00D 269 0184 907 KRA102S-RTK/P (10K-10K) TR244-246 00D 269 0192 902 KRC102S-RTK/P (10K-10K) D101 00D 276 0794 900 KDS160-RTK/P D103 00D 276 0724 912 SARS01T (V0) D104 00D 276 0794 900 KDS160-RTK/P D105-108 00D 276 0780 901 SFPX-62 +C D109-112 00D 276 0773 905 RB501V-40 +2125 D113,114 00D 276 0794 900 KDS160-RTK/P ZD101 00D 276 0848 908 UDZS22B-TE17 LD101 00D 262 3047 008 PC123Y22 LD205 00D 393 9654 003 SLI343YY3F (YEL) LD206 00D 393 9655 002 SLI343UR3F (RED) LD207 00D 393 9668 002 SLR343BCT3F LD241 00D 393 9668 002 SLR343BCT3F FL241 00D 393 8084 001 VFD (15-BT-102GN) R113,114 00D 244 2671 927 RS14B3D0R1JNBST(S) R115 00D 244 2043 953 RS14B3A471JNBST(S) R116 00D 244 2051 987 RS14B3A4R7JNBST(S) RESISTORS GROUP CAPACITORS GROUP C101-104 nsp CK73F1H103ZT +1608 C107-114 nsp CK73F1H103ZT +1608 C115 nsp RM73B--0R0KT +1608 C119-121 nsp RM73B--0R0KT +1608 C122-124 nsp CK73F1H103ZT +1608 C125 nsp CK73F1E104ZT +1608 C126 nsp CK73F1H103ZT +1608 C127 nsp CK73B1H102KT +1608 C128 00D 253 1210 901 C129 nsp CK73F1H103ZT +1608 C130 nsp CK73B1H102KT +1608 C131 00D 254 4709 700 CE04W1V221MC JC5(KY) C132 00D 253 1210 901 CK45B1H104KT(RPER) CK45B1H104KT(RPER) 82 Remarks Q'ty New S-102 Ref. No. C133 Part No. nsp Part Name CK73F1H103ZT +1608 C134 nsp CK73B1H102KT +1608 C135 nsp CK73F1E104ZT +1608 C136 nsp CK73F1H103ZT +1608 C137 nsp CK73B1H102KT +1608 C138 00D 254 4709 700 C140 nsp C141 00D 254 4721 911 C142 nsp CK73F1E104ZT C143 nsp CC73CH1H471JT C145 nsp CK73B1E223KT C146 00D 253 8033 709 C147 nsp CK73B1H103KT (1608) +1608 C148,149 nsp CK73F1H103ZT +1608 C150 nsp CK73F1E104ZT +1608 C151 00D 255 4261 704 CQ93P2J222KC(ECQP) C152 00D 254 4807 709 CE04W1E102MC K20(KY) C153 00D 254 4713 903 C154,155 nsp CE04W1V221MC JC5(KY) CK73F1E104ZT +1608 CE04W1V100MT(GR) +1608 +1608 +1608 CK45B3D470KC(DEA) CE04W1E331MT JC5(KY) CK73F1E104ZT +1608 C156 00D 254 4718 940 C157 nsp CK73B1H102KT +1608 nsp CK73F1E104ZT +1608 C158,159 C160 00D 254 4718 940 C161 00D 254 4807 709 C162,163 nsp CE04W1C101MT(GR) CE04W1C101MT(GR) CE04W1E102MC K20(KY) CK73F1E104ZT +1608 C164 00D 254 4718 940 CE04W1C101MT(GR) C165 00D 254 4711 918 CE04W1A221MT F11(KY) C166 00D 254 4713 903 C167,168 nsp CE04W1E331MT JC5(KY) CK73F1E104ZT +1608 C169 00D 254 4718 940 CE04W1C101MT(GR) C170 00D 254 4711 918 CE04W1A221MT F11(KY) C171 nsp CK73F1H103ZT +1608 C173,174 nsp CK73F1E104ZT +1608 C175 nsp CK73F1H103ZT +1608 C177,178 nsp CK73F1E104ZT +1608 C179,180 nsp CK73F1H103ZT +1608 C181 nsp CK73F1E104ZT +1608 C182 nsp CK73F1H103ZT +1608 C183 nsp CK73F1E104ZT +1608 C184 nsp CK73F1H103ZT +1608 C185 nsp CK73F1E104ZT +1608 C186 nsp CK73F1H103ZT +1608 C188 nsp CK73F1H103ZT +1608 C189 nsp CK73F1E104ZT +1608 C190 nsp CK73F1H103ZT +1608 C191 nsp CK73F1E104ZT +1608 C192 nsp CK73B1H103KT (1608) +1608 C193 nsp CK73B1H102KT +1608 C194 nsp CK73F1E104ZT +1608 C195 nsp CK73B1H103KT (1608) +1608 C196,197 nsp CK73B1H102KT +1608 C198 nsp CK73F1E104ZT +1608 C199 nsp CK73F1H103ZT +1608 C200 nsp CK73B1H102KT +1608 C201-203 nsp CK73F1E104ZT +1608 C205-207 nsp CK73B1H102KT +1608 83 Remarks Q'ty New S-102 Ref. No. Part No. Part Name C208,209 nsp CK73F1H103ZT +1608 C212 nsp CK73F1H103ZT +1608 C221-224 nsp CK73F1E104ZT +1608 C225,226 nsp CK73B1H222KT +1608 C227,228 nsp CK73F1E104ZT +1608 C241 nsp CK73F1H103ZT +1608 C242,243 nsp CK73F1E104ZT +1608 C244 00D 254 4737 947 C245 nsp C246 nsp C247 00D 254 4737 947 CE04W1H010MT(SF) CK73F1E104ZT +1608 CC73CH1H750JT +1608 CE04W1H010MT(SF) C248 nsp CK73F1E104ZT +1608 C249,250 nsp CK73F1H103ZT +1608 C251 nsp CK73F1E104ZT +1608 C252 nsp CK73B1H102KT +1608 C253 nsp CK73F1E104ZT +1608 C254 nsp CK73B1H102KT +1608 C256 00D 254 4732 955 C257 nsp CK73F1H103ZT C264 nsp CK73B1E104KT +1608 C265 nsp CK73F1H103ZT +1608 C282 00D 257 2018 900 CE04W0J221MT(SF) +1608 CS77B1A100MT(NOJ) C283,284 nsp CK73B1H102KT +1608 C285-287 nsp CK73F1E104ZT +1608 C288,289 nsp CK73F1H103ZT +1608 C290 nsp CK73B1H102KT +1608 C291,292 nsp CK73F1H103ZT +1608 C293 nsp CK73B1H102KT +1608 C294-296 nsp CK73F1H103ZT +1608 CK73F1E104ZT +1608 C297-300 nsp C301 00D 254 4722 981 CE04W1H100MT(GR) C302 nsp CK73F1E104ZT +1608 C303 nsp CK73B1H102KT +1608 C306 nsp CK73B1E223KT +1608 C307 nsp CK73B1E104KT +1608 OTHERS PARTS GROUP AS103 AS202-204 00D 417 0476 007 RADIATOR nsp FL SPACER CW051 00D 203 8582 022 5P PH-SAN CON.CORD CW052 00D 203 8581 023 5P ZH-SAN CON.CORD CX021 nsp CX091,092 CX141 CY091,092 00D 205 1338 033 nsp 00D 205 1440 002 2P VH CON BASE (White) 9P CON.BASE(9117S) 14P SOCKET(9120) 9P PIN HEADER(9210B) CY141 nsp 14P PIN HEADER(9120) CY142 nsp 14P SOCKET(9120) CY171 00D 205 1100 038 17P FFC BASE(P=1) CY211 00D 205 1006 022 21P FFC BASE (P=1) FB104 00D 235 0049 900 BEADS INDUCTOR TAPE FB105-110 00D 235 0130 903 CHIP EMIFIL(11A121) +1608 84 Remarks Q'ty New S-102 Ref. No. Part No. Part Name FB111-114 00D 235 0049 900 BEADS INDUCTOR TAPE FB221-223 00D 235 0130 903 CHIP EMIFIL(11A121) +1608 FB291-293 00D 235 0130 903 CHIP EMIFIL(11A121) +1608 JK101 nsp 25P DSUB(MALE) JK201 00D 204 8636 010 MINI JACK(ST SW) JK291 00D 204 8636 010 MINI JACK(ST SW) L101,102 00D 235 0184 014 INDUCTOR 10UH(7208M) S205-207 00D 212 5611 903 TACT SWITCH(TAPE H5) S281 00D 212 0527 005 ROTARY ENCODER S282-285 00D 212 5611 903 TACT SWITCH(TAPE H5) ST101,102 nsp T101 STYLE PIN 00D 231 8084 004 DC-DC TRANS(ST3193) 0RD 470 0051 009 3X8 CPS(SW,W) ZNP 85 Remarks Q'ty New S-102 1U-3811D/E/F D.AMP/SMPS P.W.B. UNIT ASS'Y Ref. No. Part No. Part Name Remarks SEMICONDUCTORS GROUP ! IC101-103 00D 263 1277 909 IC201 00D 262 3502 909 RC4580IDR TAS5066PAGRG4 IC202 00D 262 3504 907 SN74HCU04APWR IC203,204 00D 262 3501 900 PCM1803DBR IC205 00D 263 1100 005 KIA7805API-U/P IC206 00D 262 3503 911 TAS5142DKD IC207 00D 262 3503 908 TAS5121DKDR IC208 00D 262 3082 924 BD4730G-TR IC401 00D 265 0118 007 STR-F6267S(LF1351) for E2 IC401 00D 265 0116 009 STR-F6238S(LF1351) for E3, JP IC402 00D 262 3508 903 SPI-8002TW IC403 00D 263 1100 021 KIA7812API-U/P IC404 00D 263 1099 022 KIA7912PI-U/P IC405 00D 263 1155 005 SE-B2(LF12) IC406 00D 263 1100 063 KIA7809API-U/P IC407 00D 262 3047 008 PC123Y22 TR101,102 00D 273 0460 905 KTC2875-B-RTK/P TR103,104 00D 269 0192 902 KRC102S-RTK/P (10K-10K) TR105 00D 273 0460 905 KTC2875-B-RTK/P TR110 00D 269 0184 907 KRA102S-RTK/P (10K-10K) TR201 00D 273 0464 901 KTC3875S-GR-RTK/P TR202,203 00D 271 0312 905 KTA1504S-GR-RTK/P TR204 00D 273 0464 901 KTC3875S-GR-RTK/P TR205 00D 269 0192 902 KRC102S-RTK/P (10K-10K) TR206 00D 273 0468 907 KTC3199-GR-AT/P TR207 00D 269 0184 907 KRA102S-RTK/P (10K-10K) TR208 00D 269 0192 902 KRC102S-RTK/P (10K-10K) TR401 00D 273 0468 907 KTC3199-GR-AT/P TR402,403 00D 273 0464 901 KTC3875S-GR-RTK/P TR404 00D 271 0320 900 KTA1517-GR-RTK/P TR405 00D 274 0160 907 2SD2144STPU TR406,407 00D 271 0320 900 KTA1517-GR-RTK/P TR601,602 00D 269 0192 902 KRC102S-RTK/P (10K-10K) D101 00D 276 0401 905 1SS133T77 (TAPE) D102-107 00D 276 0773 905 RB501V-40 D113 00D 276 0401 905 1SS133T77 (TAPE) D201-206 00D 276 0750 902 RB521S-30TE61 D207-212 00D 276 0401 905 1SS133T77 (TAPE) D213,214 00D 276 0717 903 1SS355 TE-17 D215,216 00D 276 0401 905 1SS133T77 (TAPE) D217 00D 276 0401 905 1SS133T77 (TAPE) +2125 D401,402 00D 276 0401 905 1SS133T77 (TAPE) D403,404 00D 276 0750 902 RB521S-30TE61 D405 00D 276 0802 009 GS1B660 D406-410 00D 276 0750 902 RB521S-30TE61 D411,412 00D 276 0727 919 AL01ZT (WK) D413 00D 276 0758 001 SARS03 D414 00D 276 0727 919 AL01ZT (WK) D415,416 00D 276 0772 003 1N4004 D417 00D 276 0401 905 1SS133T77 (TAPE) D418,419 00D 276 0782 909 RN1Z D420 00D 276 0832 008 FMX-G22S +REF +C for E3, JP +REF +REF 86 Q'ty New S-102 Ref. No. Part No. Part Name Remarks D423 00D 276 0401 905 1SS133T77 (TAPE) D424 00D 276 0773 905 RB501V-40 D425 00D 276 0401 905 1SS133T77 (TAPE) D426,427 00D 276 0825 905 SFPB-74V ZD201,202 00D 276 0823 907 P4SMAJ33CA ZD401 00D 276 0761 975 MTZJ18B T77 LD601 00D 393 9666 004 LED(RED) SLI-560UT TH401 00D 279 0045 001 NTPAJ6R0LDKB0 R261 00D 247 0059 951 RM73B--2R7FT(RL1220 1/4) +2125 R264 00D 247 0059 951 RM73B--2R7FT(RL1220 1/4) +2125 R401 00D 242 2009 001 RC1/2 225K B(UL) R402 00D 242 2009 001 RC1/2 225K B(UL) R404 00D 244 2051 961 RS14B3A101JNBST(S) R411 00D 243 2094 019 RW99=3DR22JF R411 00D 243 2094 035 RW99=3DR10JF for E3, JP R412 00D 243 2094 019 RW99=3DR22JF for E2 R412 00D 243 2094 006 RW99=3DR12JF for E3, JP R414 00D 244 2682 916 RS14B3D104JNBST(S) for E2 R414 00D 244 2682 932 RS14B3D333JNBST(S) for E3, JP R419 00D 241 2313 985 RD14B2E4R7JFRST R424 00D 244 2051 990 RS14B3A472JNBST(S) R427 00D 247 2019 902 RM73B--102FT R428 00D 245 2385 928 RN14K2E393FT(EROS2) R450,451 00D 243 2094 035 RW99=3DR10JF R453 00D 244 2675 732 RS14B3D104JNBF(ERG) for E2 R453 00D 244 2675 716 RS14B3D683JNBF (ERG) for E3, JP +2125 for E3, JP RESISTORS GROUP for E3 for E2 +1608 CAPACITORS GROUP C101-104 00D 254 4722 981 C105,106 nsp C107,108 00D 254 4722 981 C109,110 nsp C111,112 00D 254 4722 981 C113 C114,115 nsp 00D 254 4722 981 CE04W1H100MT(GR) CC73CH1H101JT CE04W1H100MT(GR) CK73B1E104KT CK73B1H102KT nsp CK73B1H102KT nsp CC73CH1H101JT C120 nsp C121 nsp C122 00D 254 4722 981 +1608 CE04W1H100MT(GR) C117 00D 254 4722 981 +1608 CE04W1H100MT(GR) C116 C118,119 +1608 +1608 +1608 CE04W1H100MT(GR) CC73CH1H101JT CK73B1E104KT +1608 +1608 CE04W1H100MT(GR) C123 nsp CK73B1H102KT +1608 for E3, E2 C123 nsp RM73B--0R0KT +1608 for JP CK73B1E104KT +1608 C124 nsp C125 00D 254 4722 981 CE04W1H100MT(GR) C126 nsp RM73B--0R0KT C127 nsp CC73CH1H101JT C128 00D 254 4722 981 C129,130 C131 nsp 00D 254 4722 981 +1608 +1608 CE04W1H100MT(GR) CK73B1E104KT +1608 CE04W1H100MT(GR) 87 for JP Q'ty New S-102 Ref. No. C132 Part No. 00D 254 4722 936 Part Name Remarks CE04W1HR47MT(GR) C133 nsp C134 00D 254 4722 981 CK73B1H102KT +1608 C135 nsp CC73CH1H101JT +1608 C136 nsp CC73CH1H471JT +1608 C137 00D 254 4722 981 C138 nsp CK73B1E104KT C139 nsp CK73B1E104KT +1608 C139 nsp RM73B--0R0KT +1608 for JP C201 nsp CK73B1H102KT +1608 for E3, E2 CE04W1H100MT(GR) CE04W1H100MT(GR) +1608 for E3, E2 C201 nsp RM73B--0R0KT +1608 for JP C202 nsp RM73B--0R0KT +1608 for JP C203 nsp CK73B1E104KT +1608 for E3, E2 C203 nsp RM73B--0R0KT +1608 for JP C204 nsp CC73CH1H5R0CT C205-207 00D 254 4722 981 C208-210 nsp C211-213 00D 254 4722 981 C214,215 nsp C216,217 00D 254 4722 981 C218,219 nsp C220 00D 254 4722 981 +1608 CE04W1H100MT(GR) CK73B1H103KT (1608) +1608 CE04W1H100MT(GR) CK73B1E104KT +1608 CE04W1H100MT(GR) CK73B1E104KT +1608 CE04W1H100MT(GR) C221 nsp C222 00D 254 4722 981 C223 nsp CK73B1E104KT +1608 C224 nsp CK73B1A224KT +1608 C225 00D 254 4722 981 C226 nsp C227 00D 254 4711 905 C228 nsp C232 nsp C233 00D 254 4759 909 C234 nsp C235 00D 254 4759 909 C236 nsp CK73B1A224KT C237 nsp CK73B1H103KT (1608) +1608 C238 00D 254 4759 909 C240 nsp C241 00D 254 4651 900 C243 C244,245 nsp 00D 254 4759 909 C248 nsp C249 00D 254 4718 953 C250,251 C252 C253,254 C259 C260,261 nsp 00D 254 4718 953 nsp nsp 00D 254 4759 909 CK73B1E104KT +1608 CE04W1H100MT(GR) CE04W1H100MT(GR) CK73B1E223KT +1608 CE04W1A471MT HB5(KY) CK73B1H103KT (1608) +1608 CK73B1E104KT +1608 CE04W1H100MT E11(KY) CK73B1E104KT +1608 CE04W1H100MT E11(KY) +1608 CE04W1H100MT E11(KY) CK73B1H103KT (1608) +1608 CE04W0J331MT F11(KY) CK73B1A224KT +1608 CE04W1H100MT E11(KY) CK73B1E104KT +1608 CE04W1C221MT(GR) CK73B1H103KT (1608) +1608 CE04W1C221MT(GR) CK73B1E104KT +1608 CK73B1E104KT +1608 CE04W1H100MT E11(KY) C262-266 nsp CK73B1E104KT +1608 C267 nsp CK73B1E333KT +1608 C270,271 nsp CK73B1E333KT +1608 C274 nsp CK73B1E333KT +1608 C275,276 nsp CK73B1E104KT +1608 C277 nsp CK73B1H103KT (1608) +1608 C278 nsp CK73B1E104KT +1608 C279 nsp CK73F1C105ZT +2125 C280 nsp CK73B1E333KT +1608 88 Q'ty New S-102 Ref. No. C281,282 Part No. nsp Part Name CK73B1H104KT +2125 C283 nsp CK73B1E333KT +1608 C284 nsp CK73F1C105ZT +2125 CK73B1H102KT +1608 C285-288 nsp C289,290 00D 254 4718 953 C299-302 nsp C303-306 00D 254 4641 907 CE04W1C221MT(GR) CK73B1H103KT (1608) +1608 CE04W1H470MT F11(LXZ C307 nsp CK73B1H104KT C308 nsp CC73CH1H5R0CT C309,310 nsp CK73B1H104KT C311 nsp CK73B1H103KT (1608) +1608 C312 nsp CK73B1H104KT C313,314 nsp CK73B1H103KT (1608) +1608 C316 nsp CK73B1H103KT (1608) +1608 C317,318 nsp CK73B1H104KT C319,320 +2125 +1608 +2125 +2125 +2125 nsp CK73B1H103KT (1608) +1608 C323 00D 257 3013 933 CF73=1H104JT(ECHUC9) +C C324 00D 254 4714 708 CE04W1V222MC LN3(KY) C325 00D 257 3013 933 CF73=1H104JT(ECHUC9) +C C326 00D 254 4714 708 CE04W1V222MC LN3(KY) C335 nsp C336-338 00D 256 1067 904 C339 nsp C401 00D 253 8026 703 C402,403 nsp Remarks CK73B1H102KT +1608 CF93A2A474JT(ECQV) CK73B1E104KT +1608 CK45E2EAC472MC RM73B--0R0KT +1608 for E2 ! IC405 00D 256 8039 003 CF99--2EAC104K(LEMX) for E2, JP ! IC405 00D 256 8039 016 CF99--2EAC224K(LEMX) for E3 ! IC406 00D 256 8039 016 CF99--2EAC224K(LEMX) for E3 ! IC406 00D 256 8039 029 CF99--2EAC334K(LEMX) for JP ! IC407 nsp ! IC408-410 00D 253 8035 707 CK45E2EAC102MC(KY) ! IC408-410 00D 253 8035 710 CK45E2EAC222MC(KY) for E3, JP ! IC411 00D 253 8030 003 CK45B3D681KC(ECKA) for E2 CK73B1H103KT (1608) +1608 for E2 ! IC411 00D 255 4261 704 CQ93P2J222KC(ECQP) for E3, JP ! IC412 00D 256 8039 016 CF99--2EAC224K(LEMX) for E3 ! IC412 00D 256 8039 003 CF99--2EAC104K(LEMX) for JP ! IC413,414 00D 256 8039 003 CF99--2EAC104K(LEMX) C418,419 nsp CK73B1E223KT +1608 C421 nsp CK73B1H332KT +1608 C422 nsp CC73CH1H221JT C423 nsp CK73B1H103KT (1608) +1608 C425 00D 254 4618 901 C426-429 C430 I! nsp 00D 254 4721 995 C431 nsp C432 00D 254 6229 000 +1608 CE04W1H101MT H12(LXZ CK73B1H103KT (1608) +1608 CE04W1V102MT(GR) CK73B1H103KT (1608) +1608 CE68W2G331M 35B(KMM) for E2 for E3, JP C432 00D 254 6228 001 CE68W2D102M 35B(KMM) C433 00D 254 4639 906 CE04W1H4R7MT(KMG) C434 nsp C435 00D 255 4261 717 CQ93P2J332KC(ECQP) for E2 C435 00D 255 4261 762 CQ93P2J103KC(ECQP) for E3, JP C436 00D 254 4728 707 CE04W1E332M (GR) C437 nsp C439 00D 254 4718 940 C440 nsp C441 nsp C442 00D 253 8032 700 CK73B1H102KT CK73B1E104KT +1608 +1608 CE04W1C101MT(GR) CK73B1E104KT +1608 CK73B1C473KT +1608 CK452EAC102MC(KX) for E2 89 Q'ty New S-102 Ref. No. I! C442 Part No. 00D 253 8029 700 Part Name CK45F2EAC222MC (KX) C443 nsp C444 00D 254 2708 701 CE04W1E471MC J16(KY) C445 00D 255 4261 720 CQ93P2J472KC(ECQP) C446 00D 254 2708 701 CE04W1E471MC J16(KY) C447,448 00D 254 4714 708 CE04W1V222MC LN3(KY) C449 nsp C451-454 nsp C455,456 00D 254 4718 953 CK73B1E104KT +1608 CK73B1H103KT (1608) +1608 CK73B1H103KT (1608) +1608 CE04W1C221MT(GR) C457 nsp CC73CH1H221JT +1608 C458-460 nsp RM73B--0R0KT C461 nsp CK73B1H105KT C462 nsp CK73B1H103KT (1608) +1608 C464,465 nsp CK73B1E104KT C466 nsp CK73B1H103KT (1608) +1608 C467 00D 254 4722 952 C468 nsp C469 00D 254 4711 905 C470 nsp C471 00D 254 4712 700 +1608 +1608 CE04W1H2R2MT(GR) CK73B1H103KT (1608) +1608 CE04W1A471MT HB5(KY) CK73B1H103KT (1608) +1608 CE04W1C471MC JC5(KY) C472,473 nsp CK73B1E104KT C474 nsp CK73B1H103KT (1608) +1608 +1608 C475 nsp CK73B1H102KT C476 nsp CK73B1H103KT (1608) +1608 +1608 C477 nsp CK73B1H102KT +1608 C479 nsp CK73B1E104KT +1608 C481 nsp CK73B1H102KT +1608 C482-484 nsp RM73B--0R0KT +1608 C485 00D 253 8029 700 CK45F2EAC222MC (KX) C604 00D 253 1210 901 CK45B1H104KT(RPER) C606 nsp CK73B1H102KT C616 nsp CK73B1H103KT (1608) +1608 C619 nsp CK73B1H102KT C620 nsp CK73B1H103KT (1608) +1608 C624 nsp +1608 +1608 CK73B1H103KT (1608) +1608 C625,626 00D 255 1264 908 CQ93M1H102JT(B) C627 00D 253 1210 901 CK45B1H104KT(RPER) C630,631 00D 255 1264 908 CQ93M1H102JT(B) OTHERS PARTS GROUP AS401 nsp HEAT SINK (MINI) AS402,403 nsp RADIATOR AS601 nsp LED SPACER SUPPORT A CX021 nsp 2P VH CON BASE (White) CX022 nsp 2P VH CON BASE (Blue) CX041 nsp 4P VH CON.BASE CX081 nsp 8P CONN.BASE(KR-PH) CX151 nsp 15P CONN.BASE(KR-PH) CX252 00D 205 1356 002 CY021 nsp CY023 nsp 2P VH CON BASE (White) CY042 nsp 4P VH CON.BASE CY082 nsp 8P CONN.BASE(KR-PH) CY152 nsp 15P CONN.BASE(KR-PH) 25P DSUB(FEMALE) 2P VH CON BASE (White) 90 Remarks for E3, JP Q'ty New S-102 Ref. No. ! F401 ! F401 ! F402 ! F402 FB201-204 Part No. 00D 206 1094 066 Part Name FUSE(233)T4AL125V for E3, JP 00D 206 1099 045 FUSE(02153.15MXP/250V) for E2 00D 206 1094 053 FUSE(233)T3.15AL125V for E3, JP 00D 206 1096 048 FUSE(218)T3.15AL250V for E2 00D 235 0130 903 CHIP EMIFIL(11A121) +1608 FB205,206 00D 235 0049 900 BEADS INDUCTOR TAPE FB207 00D 235 0147 909 E.FIL(BLM21PG221SN1)+2125 FB601 00D 235 0130 903 CHIP EMIFIL(11A121) +1608 FB602,603 00D 235 0049 900 BEADS INDUCTOR TAPE FB604 00D 235 0130 903 CHIP EMIFIL(11A121) +1608 FB606-608 00D 235 0130 903 CHIP EMIFIL(11A121) +1608 FB609 00D 235 0049 900 BEADS INDUCTOR TAPE FB611 00D 235 0130 903 CHIP EMIFIL(11A121) +1608 FB612-615 00D 235 0049 900 BEADS INDUCTOR TAPE FF401,402 nsp FUSE CLIP(TAPE) FH401,402 nsp FUSE CLIP(TAPE) JK601 Remarks 00D 205 1441 001 SPEAKER TERMINAL(2P) L201 00D 235 0125 905 INDUCTOR(FLC32C220K)+3216 L202 00D 235 0192 006 INDUCTOR 7G14D-100M L203 00D 231 0091 008 60NH(AIR COIL) L204,205 00D 235 0192 006 INDUCTOR 7G14D-100M L206 00D 231 0091 008 60NH(AIR COIL) L207,208 00D 235 0192 006 INDUCTOR 7G14D-100M L209-211 00D 231 0091 008 60NH(AIR COIL) L212 00D 235 0192 006 INDUCTOR 7G14D-100M L213 00D 231 0091 008 60NH(AIR COIL) L215 00D 235 0192 006 INDUCTOR 7G14D-100M ! L401,402 00D 239 0038 052 L.FILTER(HR28R-E123) for E3, JP ! L401,402 00D 239 0038 078 L.FILTER(HR28R-E333) for E2 L404,405 00D 235 0185 903 INDUCTOR 47UH(7E10H) RL201,202 00D 214 0217 010 RELAY(DS2SU12VDC) ! RL401 00D 214 0242 001 RELAY(DLS9D1-O_M) ! T401 00D 233 6604 000 SW_TRANS(E3/EJ 3590) for E3, JP ! T401 00D 233 6605 009 SW TRANS(E2/EK 3591) for E2 ! T402 00D 233 6615 002 POWER TRANS(MINI/E2) for E2 ! T402 00D 233 6614 003 POWER TRANS(MINI/E3) for E3 ! T402 00D 233 0747 002 POWER TRANS(MINI/J) for JP W101 nsp W201 nsp LUG PLATE W401-404 nsp LUG PLATE X201 00D 399 1114 905 LUG PLATE X-TAL(L8450-24.576) 0RD 470 0012 022 3X12 CPS SW W for IC401 0RD 470 0051 009 3X8 CPS(SW,W) ZNP for D413,420 nsp FUSE LABEL3.15A/125V for E3, JP nsp FUSE LABEL(4A/125V) for E3, JP 91 Q'ty New S-102 EXPLODED VIEW 110 44 30 104 103 31 30-1 45 35 2 -4 2 -7 27 107 103 32 24 1 106 48 104 109 101 5 4 -2 47 8 7 2 -6 101 33 103 105 2 -3 13 4 -1 15 46 23 12 46 102 25 103 26 104 14 18 101 3 -1 106 104 2 -5 101 3 -2 21 102 2 -1 2 -2 19 34 20 6 9 37 108 10 104 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 106 36 106 104 47 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。 92 S-102 PARTS LIST OF EXPLODED VIEW * 本表に "nsp" と記載されている部品は供給できません。 * Parts for which "nsp" is indicated on this table cannot be supplied. * 本表に "nsp" と記載されている基板 ASS’Y は供給できません。基板 ASS’Y の修理の際には基板部品表を確認のうえ、交換部品を発注してください。 * P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts. * 本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model Ref. No. Part No. JP : Japan mode Part Name Remarks Q'ty New 1 00D1U-3836D MAIN P.W.B. UNIT ASS'Y(E2) for E2 1 * 1 00D1U-3836E MAIN P.W.B. UNIT ASS'Y(E3) for E3 1 * 1 00D1U-3836F MAIN P.W.B. UNIT ASS'Y(J) for JP 1 * 2 nsp 1 * LOC/PWR-DSP P.W.B. UNIT ASS'Y(ALL) 2-1 - DISPLAY CENT. UNIT 1 2-2 - DISPLAY RIGHT UNIT 1 2-3 - DISPLAY LEFT UNIT 1 2-4 - LOCAL POWER UNIT 1 2-5 - HP OUT UNIT 1 2-6 - AUX IN UNIT 1 2-7 - IF-1 UNIT 1 3 3-1 3-2 4 4-1 4-2 00D 146 2502 103 FRONT PANEL ASSY 1 - FRONT PANEL 1 - WINDOW 1 POWER KNOB ASSY 1 - POWER KNOB CAP 1 - 00D 113 2099 001 * * KNOB BASE(POWER) 1 5 00D 143 1292 004 LENS(POWER) 1 * 6 00D 113 2094 006 KNOB(PLAY) 1 * 7 00D 113 2095 005 KNOB(EJECT) 1 * 8 00D 113 2096 004 KNOB(FUNCTION) 1 * 9 00D 113 2098 002 KNOB(STOP) 1 * 10 00D 113 2097 003 KNOB(SKIP) 1 * 12 00D 461 1298 003 BLIND SHEET 1 * 13 00D 431 0452 001 BLIND 1 * 14 00D 463 0958 007 SPRING 2 15 nsp FRONT BRACKET 1 * 18 nsp MAIN CHASSIS 1 * 19 00D 104 0351 022 FOOT 4 * 20 00D 461 1066 002 FELT 4 21 00D 415 1012 008 PROTECT SHEET 1 * 1 * 23 00D 105 1691 108 REAR PANEL 24 00D 216 0125 001 AM FM TUNER(E2) for E2 1 24 00D 216 0129 007 AM FM TUNER(E3 RDBS) for E3 1 24 00D 216 0127 009 AM FM TUNER(J) for JP 1 25 00D 421 0839 009 FAN F410T-12L1C 26 nsp FAN BRACKET 1 27 nsp SHIELD BRACKET 1 30 FG5HPS1MS DVD MECHA UNIT 1 00D1U-3807 FEP P.W.B. UNIT 30-1 1 * 1 31 00D 146 2506 031 TOP COVER for E2 1 31 00D 146 2506 044 TOP COVER for E3 1 * * 31 00D 146 2506 057 TOP COVER for JP 1 * 32 nsp TOP BRACKET 1 * 33 00D 146 2504 004 SIDE PANEL(L) 1 * 34 00D 146 2505 003 SIDE PANEL(R) 1 * 35 00D 146 2492 019 LOADER PANEL 1 * 93 S-102 Ref. No. Part No. 36 Part Name nsp CARD SPACER Remarks Q'ty New 1 37 00D 112 1000 001 VOLUME KNOB 1 ★ 38 00D 342 0040 003 FERRITE CRAMP081610N 1 ★ 39 nsp ★ 40 nsp E2 LASER CAUTION for E2 1 ★ 41 nsp LABEL(A) for E3 1 ★ 42 nsp R.SHEET(E2) SUB ASSY for E2 1 * ★ 42 nsp R.SHEET(E3) SUB ASSY for E3 1 * ★ 42 nsp R.SHEET(J) SUB ASSY for JP 1 * ★ 43 nsp MANUFAC.(J)SUB ASSY for JP 1 100mm 1 1 * 75mm 2 * 4 * CORD HOLDER (L50) L=50 * 1 44 nsp EMI GASKET RFSG100100 45 nsp FFC PAD 46 nsp EMI GASKET RFSG010070 47 nsp SPACER 48 nsp EMI GASKET RFSG100100 60mm 1 for CX151 1 * wiers ★ 51 00D 009 0236 017 15P FFC CABLE ★ 52 00D 009 0273 054 17P FFC(1.0) for CY171 1 * ★ 53 nsp 3P VH-VH CONN CORD for CX021 1 * ★ 54 00D 009 0273 067 21P FFC(1.0) for CY211 1 * ★ 55 nsp 6P PH-PH CON.CORD for MAIN-DRIVE 1 * ★ 56 00D 009 0285 026 30P FFC(1.0) for CY302 1 * 101 0RD 473 7500 015 3X8 CBTS (P)-Z 102 0RD 473 8044 004 SPECIAL SCREW 2 103 0RD 473 7005 073 3X5 CBTS(S)Z 13 104 0RD 473 7002 034 3X6 CBTS (S)-B 15 105 00D 473 8091 002 3X16 CUP SCREW 4 106 0RD 473 7015 005 3X6 CBTS(S)-B 27 107 00D 477 0064 107 FIXING SCREW 7 108 0RD 473 7002 021 3X8 CBTS (S)-B 2 109 0RD 473 7500 002 3X6 CBTS (P)-Z 5 110 0RD 473 7031 005 2.6X10 CBTS (S)-Z 4 screws 15 94 S-102 EXPLODED VIEW OF DVD MECHANISM UNIT WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。 95 S-102 PARTS LIST OF DVD MECHANISM UNIT * 本表に "nsp" と記載されている部品は供給できません。 * Parts for which "nsp" is indicated on this table cannot be supplied. * 本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Ref. No. Part No. Part Name Remarks Q'ty 1 nsp MAIN CHASSIS ASS'Y 3 00D 9KA 2A73 8 GUIDE CLAMP ASS'Y 1 1 4 00D 9KC 2A00 3 LOADING MOTOR ASS'Y 1 5 00D 9KC 2G02 9 LOADING GEAR 1 6 00D 9KB 9G03 0 LOADING GEAR 2ND 1 7 00D 9KB 9G03 1 LOADING GEAR 3RD 1 8 nsp SUB CHASSIS-L 1 9 nsp SUB CHASSIS-R 1 1 10 00D 9KA 2A73 7 TRAY ASS'Y 11 00D 9KC 1G00 3 SLIDE-CAM 1 12 00D 9KC 1G00 4 TRAVERSE ARM 1 16 00D 9KB 9G01 5 LOADING BELT 1 17 nsp SWITCH P.W.B. 1 18 nsp 5P PH WIRE 1 19 00D 9KS 01W2 04 SWITCH ESE22MH21 1 20 00D 9KS 01W2 05 SWITCH ESE22MH23 1 21 nsp 22 00D 445 8004 007 POLY.SLIT WASHER 2.6X6X0.25C 3 WIRE CLAMPER 23 1 nsp PRECISION SCREW 1.7X2.2 TYPE3 2 24 nsp SCREW 2.6X6 CBTS(B)-Z 6 25 nsp PRECISION SCREW 2X3(S) TYPE3 1 26 nsp SCREW 2X6 CBTS(P)-Z 27A 23 00D 9KA 2A69 3 - 2 TRAVERSE MECHA (FEED) ASS'Y PRECISION SCREW 1.7X2.2 TYPE3 Assembled part 1 5 27 - PU CHASSIS ASS'Y 1 28 - SHAFT HOLDER L 1 29 - SHAFT HOLDER R 1 30 - SHAFT TILT BASE-W 1 31 - SHAFT TILT PLATE-W 1 32 - TILT SPRING 2 33 - MAIN SHAFT 1 34 - SUB SHAFT 1 35 - PU RACK GEAR 1 36 - FEED GEAR 2ND ASS'Y 1 37 - PICK UP SF-HD65G 1 39 - SHAFT SPRING 1 1 40 - RACK GEAR SPRING 41 - FEED MOTOR ASS'Y 1 42 - T/T MOTOR ASS'Y 1 43 - SCREW 2.6X6 CBTS(S)-Z 2 44 - SCREW 2.6X4 CBTS(S)-Z 1 46 - SCREW 2.6X15 CFTS(S)-Z 2 47 - SCREW 3X4 BSS 2 48 - SCREW 3X8 BSS (A) 1 50 - POLY.SLIT WASHER 2.1X4X0.25C 2 53 - FEED GEAR 3RD 1 49 00D 9KA 2G64 3 DAMPER 4 51 00D 9KC 1H01 2 SPECIAL SCREW 4 54 nsp TRAY-SPRING-VXF 1 56 nsp RUBBER CUSHION 2 59 nsp TRAY-CUSHION 1 66 00D 009 0276 006 70 nsp 24P FFC(0.5) 1 TAPE W10X45 (NITTO NO.156) 1 96 New S-102 POINTS OF GREASING With Cemedine 575, glue 3 joint parts of Clamper-L and H hooks. (0.05mg each x 3) *As for greasing to the R rail groove and groove's side edge, apply grease to the outer face "intentionally". (Not only running a brush into the groove, use it with pressing to the outer face consciously.) After attaching cushions, apply Cemedine 575 to the joint parts of the cushions and tabs (both sides, left and right) from the tab's back side. (0.1mg each x 4) When greasing each rib, apply to the rib's left, right, and top faces properly with running a brush on both sides of the rib. Apply 12.5mm half-ball approx. After applying , check especially for the front 3 ribs outer side in order not to be insufficient greasing. Froil KG 423 After attaching plate spring, apply to the TRAY side of the plate spring. 54 Main Chassis Main Chassis 97 S-102 DSW-S102 EXPLODED VIEW 2 18 5 6 24 102 9 101 28 27 10 1-1 103 7 102 12 1-4 13 ! 105 1-2 14 17 20 19 15 16 101 11 3 101 104 4 106 107 5 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。 98 S-102 DSW-S102 PARTS LIST OF EXPLODED VIEW * 本表に "nsp" と記載されている部品は供給できません。 * Parts for which "nsp" is indicated on this table cannot be supplied. * 本表に "nsp" と記載されている基板 ASS’Y は供給できません。基板 ASS’Y の修理の際には基板部品表を確認のうえ、交換部品を発注してください。 * P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts. * 本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model Ref. No. Part No. JP : Japan model Part Name Remarks Q'ty New 1 nsp D.AMP/SMPS P.W.B. UNIT ASS'Y(E2) for E2 1 * 1 nsp D.AMP/SMPS P.W.B. UNIT ASS'Y(E3) for E3 1 * 1 nsp D.AMP/SMPS P.W.B. UNIT ASS'Y(J) for JP 1 * 1-1 SMPA/AMP UNIT 1 1-2 I/F UNIT 1 1-4 AC I/F UNIT 1 DSWS102 CABINET ASSY 1 * 2 00D 9H3 0001 728 3 00D 105 1680 232 REAR PANEL 1 * 4 00D 104 0354 003 FOOT(REAR) 2 * 5 00D 461 1300 001 FELT 4 * 6 nsp MAIN BRACKET 1 * 1 7 nsp P.W.B.HOLDER (H=12) 9 nsp HEAT SINK 1 * 10 nsp SHIELD COVER 1 * 11 nsp CONNECTOR BRACKET 1 * TERMINAL COVER 1 * CORD BUSH 3 12 nsp 13 00D 445 0084 009 14 nsp PEF SHEET(7x48) 2 * 15 nsp PEF SHEET(7x177) 2 * 16 nsp PEF SHEET(10x180) 2 * 17 nsp PEF SHEET(10x233) 2 * 18 00D 104 0353 004 FOOT(FRONT) 2 * ! I19 00D 206 2244 006 AC CORD E2withCON(V) for E2 1 ! I19 00D 206 2245 005 AC CORD E3withCON(V) for E3 1 ! I19 00D 206 2248 002 AC CORD JwithCON (V) for JP 20 00D 445 0131 004 CORD BUSH(SR-5K4) 1 ★ 21 00D 461 1316 008 PEF SHEET(10x10) 1 * 2 * ★ 22 nsp ★ 23 00D 342 0040 003 SPACER(CPVS-0.5F) FERRITE CRAMP081610N CX041 1 1 24 nsp PWB PAD 1 * ★ 25 nsp PEF SHEET(10x15) 5 * ★ 26 nsp PEF SHEET(30x120) 4 * 27 nsp CABINET PAD(70X15) 1 * 28 nsp CABINET PAD(70X15) 1 * ★ 29 nsp RATING SHEET(E2) 1 * ★ 29 nsp RATING SHEET(E3) 1 * ★ 29 nsp RATING SHEET(J) 1 * ★ 30 nsp DATE LABEL 1 ★ 51 00D 203 6644 001 4P VH-VH CON.CORD ★ 52 00D 204 3021 002 ★ 53 00D 203 2447 008 ★ 54 00D 204 6821 018 wires CX04-1CY042 1 * 8P PH-PH CON.CORD CX081-CY082 1 * 2P VA-VA CON.CORD CX021-CY021 1 * 15P PH-PH CON.CORD CX151-CY152 1 * 99 S-102 Ref. No. Part No. Part Name Remarks Q'ty screws 101 0RD 473 3809 011 4X25 CBTS (1) 102 nsp 3X6 CBTS(S)-Z 7 103 nsp 3X6 CBTS(S)-B 10 104 nsp 3X8 CBTS (S)-B 9 105 nsp 3X10 CBTS (P)-Z 5 106 nsp 3X12 CBTS (P)-B 6 107 00D 477 0064 107 FIXING SCREW 1 HEXAGON HEAD SCREW SET 2 ★ 108 nsp 14 100 New S-102 SC-S102 PARTS LIST OF EXPLODED VIEW 1 SC-S102 PARTS LIST OF EXPLODED VIEW Ref. No. Part No. 1 00D 9H3 0001 727 Part Name SPEAKER SYSTEM(L&R) 101 Remarks Q'ty New 2 * S-102 PACKING VIEW 10 30 2 3 29 4 18 19 28 20 28 11 8 12 15 9 6 5 7 1 102 17 S-102 PARTS LIST OF PACKING & ACCESSORIES * 本表に "nsp" と記載されている部品は供給できません。 * Parts for which "nsp" is indicated on this table cannot be supplied. * 本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model Ref. No. Part No. JP : Japan model Part Name Remarks Q'ty New * 1 00D 501 2374 033 MASTER CARTON for E2 1 1 00D 501 2374 017 MASTER CARTON for E3 1 * 1 00D 501 2374 020 MASTER CARTON for JP 1 * 2 00D 502 1143 103 TOP SPACER 1 * 3 00D 505 0312 057 CABINET COVER 1 * 4 00D 503 1554 009 CUSHION(L) 1 * 5 00D 503 1555 008 CUSHION(R) 1 * 6 00D 505 0312 060 CABINET COVER 1 7 00D 9H3 0001 725 CUSHION DSW(BOTTOM) 1 8 00D 9H3 0001 724 CUSHION DSW(UP) 1 9 00D 9H3 0001 721 CUSHION SC(BOTTOM) 1 10 00D 9H3 0001 720 CUSHION SC(UP) 1 11 00D 104 0355 002 SP STAND(EASY) 2 12 00D 461 1236 007 PORON (HH48 F10 T1) 4 15 00D 505 0038 030 POLY COVER 1 16 00D 511 4645 000 INST. MANUAL(E2) for E2 1 * 16 00D 511 4646 009 INST. MANUAL(E3) for E3 1 * 16 00D 511 4647 008 INST. MANUAL(J) for JP 1 * 17 nsp S.S.LIST(EX) for E3, E2 1 SERVICE STATION LIST for JP 1 17 nsp 18 00D 399 1102 001 19 20 REMOCON(RC1073) 1 nsp POLY COVER 1 nsp POLY COVER 1 21 nsp BATTERY (SUM-3) ASS 1 22 00D 203 0380 002 1P PIN CORD (VIDEO) 1 23 00D 231 1152 001 AM LOOP ANTENNA(S) 24 00D 395 0026 005 FM ANT. WIRE for E2 for E3, JP * * 1 1 24 00D 395 0028 003 FM ANT ASS Y(F/WELT) 25 00D 461 1237 006 PORON (HH48 F6 T1) 1 1 26 00D 505 0343 000 ENVELOPE 1 27 0RD 471 3508 028 5X14 CBS-B 4 28 00D 203 2443 002 SP WIRE KIT(NLB193) 1 29 00D 204 6794 006 25P D-SUB CABLE 1 30 00D 511 4648 007 SETUP GUIDE 1 * * ★ 31 nsp WARRANTY (HOME) for E3 1 ★ 32 nsp UPC LABEL for E3 1 * ★ 33 nsp E2 POS LABEL for E2 2 * ★ 33 00D 517 1506 027 POS LABEL for JP 1 * ★ 34 nsp DATE LABEL for JP 1 ★ 35 nsp CONT.CARD(L)SUB ASSY for E3, E2 1 ★ 36 nsp GUARANTEE(S)SUB ASSY for JP 1 103 S-102 WIRING DIAGRAMS ADV-S102 H/P JACK Portable IN JACK CX092 CX092 5P SAN CW052 1U-3831 DISPLAY Right UNIT 1U-3831 DISPLAY Center UNIT CY091 FL Display 1U-3831 HP UNIT CX091 S102 WIRING DIAGRAM 1U-3831 AUX IN UNIT 1U-3831 DISPLAY Left UNIT 5P SAN CW051 CY211(21P FFC) 00D 009 0273 067 21P FFC Cable 00D 203 8581 023 +3.3V_D1 +3.3V_NSW +9V_DNS GND_D1 FL1 FL2 CX021(2PVH) PARAREL ATA 00D 203 8582 022 CX301(30P FFC) 00D 009 0285 026 㪊㪇㪧㩷㪝㪝㪚 㪚㪸㪹㫃㪼 1U-3805 FE DRIVE UNIT (TOHEI) CX211(21P FFC) CY301(30P FFC) FE DRIVE UNIT (᧲⧷) FL control. LED control. KEY/VOL DIMMER REMOTE CX051(5P PH) FL/FR+ FL/FRC/SW+ C/SWSL/SR+ SL/SR- 1U-3831 IF1 UNIT 00D 009 0273 054 17P FFC Cable +12V_M GND_D +5V_D CX052(5P ZH) HP out L/R㵘out HP_SW CX171(17P FFC) DSW control. CY171(17P FFC) 00D 203 5313 016 +9V_NSW GND_M GNDA -12V_A +12V_A GND_A GND_V +5V__V CY141(14P B to B) 00D 204 0606 002 Portable in L/R in FRIN_SW CY142(14P B to B) CX061(6P PH) CY061(6P PH) 1U-3836 MAIN UNIT (BE/AUDIO-PLD/SYSuCOM/AVuCOM/AUDIO-DSP) 1U-3831 LOCAL POWER UNIT CX151(15P FFC) 00D 009 0236 017 15P FFC Cable 2P VH-VH +HB GND_HB CX021(2P VH) Component IN 䌸䋱 Component OUT 䌸䋱 YC䋬CVBS IN 䌸3 YC䋬CVBS OUT 䌸1 AUX L/R IN x3 ZONE2 L/R OUT x1 SB PREOUT x1 TUNER control. RST/MUTE FMAM L/R OUT +12V_A GND_A 15P FFC FM/AM TUNER +HB GND_HB +9V_DNS L/R/SW Signal DSWuCOM control. PROT/RELAY PDOWN/CONNECT FM/AM ANT CX031(3P PH) 25P SYSTEM CABLE to DSW 㪝㪘㪥 AUX1 VIDEO IN AUX2 VIDEO OUT VIDEO OUT HDMI OUT S-VIDEO COMPONENT 104 PROGRESSIVE SW HDMI INTERACED PROGHRESSIVE Audio In AUX1 AUX12 DOCK Controlx1 AUX1Dig.IN(OPT) x 1 3811-4 AC I/F UNIT 3811-3 I/F UNIT CY041 (VH)WHT CX151 (PH) CY151 (PH) CY081 (PH) DSUB25P FEMALE SP TERMINAL 105 203 2447 008 204 3021 002 CX041 (VH)WHT 204 6821 005 Shield 203 6644 001 CX021 (VH)WHT 3811-1 SMPS/AMP UNIT CX081 (PH) CY021 (VH)WHT CY023 (VH)WHT DSW-S102 Inetrnal SP CX022 (VH)BLU S-102 DSW-S102 S-102 MEASURING METHOD AND WAVEFORMS 各部の波形と測定方法 To check the waveforms on the FEP, the GND (-) probe of the oscilloscope to “VHALF” point. (Except for lnner SW, TRVSW) FEP 基板の波形チェックを行うためにはオシロスコープの GND(-) プローブを "VHALF" ポイントに接続します。 注 意 NOTES Measuring Disc: DVD/VT502 or TDV-520A CD/TCD-784 (It is better to use wires for extending between the probe and test points.) • When watching the HF waveform, use the extending wire as short as possible. • When HF waveform is noisy or cannot discriminate the eye-pattern, replace the Traverse Unit after measuring the lop. • ① ~ ⑬ points have the certain test points shown below. 測定ディスク: DVD/VT502 or TDV-520A CD/TCD-784 (テストポイントとプローブ間に延長ワイヤを使用するの がより良い方法です。) ・ HF 波形を観測する場合、できるだけ短い延長ワイヤを 使用してください。 ・ HF 波形がノイズで不明瞭、またはアイパターンが識別 不能の場合は Iop 測定後にトラバースユニットを交換し てください。 ・ ポイント①∼⑬は、下図のように特定テストポイント付 きです。 13 7 5 4 2 8 3 6 9 12 14 11 10 1 IU-3807 FEP Unit : Foil Side * For ARF ① , use NARF ② as the reference (probe - ) for the oscilloscope, VHALF ⑭ as the reference voltage for other points. * ARF ①は NARF ②をオシロスコープの基準 ( プローブー ) とし、他のポイントの基準電圧は VHALF ⑭です。 106 S-302 WAVEFORMS IU-3807 FEP Unit. DVD PLAY Disc : TDV-520A CD PLAY Disc : TCD-784 RF waveform RF waveform ①ARF ①ARF ②NARF ②NARF RANGE .2 v DVD LOADING .05 ȝsec RANGE .2 v CD LOADING PLAY ③FODRV ③FODRV ④F+ ④F+ ⑤F- ⑤F- ③䇭.5 v RANGE ④䇭.5 v ⑤䇭.5 v ③䇭.5 v RANGE ④䇭.5 v ⑤䇭.5 v 0.5 sec DVD PLAY CD PLAY ⑥TRDRV ⑥TRDRV ⑦T+ ⑦T+ ⑧T- ⑧T- ⑥䇭.2 v RANGE ⑦䇭.2 v ⑧䇭.2 v ⑥䇭.2 v RANGE ⑦䇭.2 v ⑧䇭.2 v 100 ȝsec .2 ȝsec PLAY 0.5 sec 100 ȝsec SEARCH (INNER㸢OUTER) SEARCH (INNER㸢OUTER) ⑨TRSDRV ⑨TRSDRV ⑩FM+ ⑩FM+ ⑪FM- ⑪FM- ⑨䇭1 v RANGE ⑩䇭1 v ⑪䇭1 v ⑨䇭1 v RANGE ⑩䇭1 v ⑪䇭1 v 50 msec DVD PLAY (INNER) CD PLAY (INNER) ⑫SPDRV ⑫SPDRV ⑬FG ⑬FG RANGE ⑫䇭.1 v ⑬䇭1 v RANGE ⑫䇭.1 v ⑬䇭1 v 1 msec 107 20 msec 1 msec S-102 NOTE FOR SCHEMATIC DIAGRAM 配線図について WARNING: Parts marked with this symbol ! have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. ! 印の部品は安全を維持するために重要な部品です。 従って交換時は必ず指定の部品を使用してください。 注) CAUTION: (1) 指定なき抵抗値は Ω、k は kΩ、M は MΩ を示す。 Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective. (2) 指定なきコンデンサーの値は μF、p は pF を示す。 WARNING: DO NOT return the unit to the customer until the problem is located and corrected. NOTICE: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. 108 (3) 各部の電圧は無信号の値を示す。 (4) この配線図は基本配線図です。改良等のため変更する ことがありますのでご了承ください。 SCHEMATIC DIAGRAMS (1/17) 1 S-102 2 3 4 5 6 7 8 A 5 7 4 8 B 13 14 C 1 3 2 D 6 10 11 9 E 12 SCHEMATIC DIAGRAMS (1/17) 1U-3807 FEP UNIT F SCHEMATIC DIAGRAMS (2/17) 1 2 S-102 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (2/17) 1U-3836-1 MAIN UNIT (1/8) (B / E BLOCK) F SCHEMATIC DIAGRAMS (3/17) 1 2 S-102 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (3/17) 1U-3836-1 MAIN UNIT (2/8) (I / F BLOCK) F SCHEMATIC DIAGRAMS (4/17) 1 2 S-102 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (4/17) 1U-3836-1 MAIN UNIT (3/8) (uCOM BLOCK) F SCHEMATIC DIAGRAMS (5/17) 1 2 S-102 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (5/17) 1U-3836-1 MAIN UNIT (4/8) (AUDIO DSP BLOCK) F SCHEMATIC DIAGRAMS (6/17) 1 2 2 S-102 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (6/17) 1U-3836-1 MAIN UNIT (5/8) (CODEC / DIR BLOCK) F SCHEMATIC DIAGRAMS (7/17) 1 2 S-102 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (7/17) 1U-3836-1 MAIN UNIT (6/8) (FUNCTION / VOLUME BLOCK) F SCHEMATIC DIAGRAMS (8/17) 1 2 S-102 3 4 5 6 7 8 A B C D E VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (8/17) 1U-3836-1 MAIN UNIT (7/8) (IP / HDMI / PLD BLOCK) F SCHEMATIC DIAGRAMS (9/17) 1 2 S-102 3 4 5 6 7 8 A B C D E VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (9/17) 1U-3836-1 MAIN UNIT(8/8) VIDEO ENCODER / IN-OUT BLOCK F SCHEMATIC DIAGRAMS (10/17) 1 2 S-102 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (10/17) 1U-3831-4 LOCAL POWER UNIT F SCHEMATIC DIAGRAMS (11/17) 1 2 S-102 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (11/17) 1U-3831-1 DISPLAY CENTER UNIT 1U-3831-2 DISPLAY RIGHT UNIT 1U-3831-3 DISPLAY LEFT UNIT 1U-3831-5 HP OUT UNIT 1U-3831-6 AUX IN UNIT 1U-3831-7 IF-1 UNIT F SCHEMATIC DIAGRAMS (12/17) 1 2 S-102 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (12/17) 1U-3811-3 I/F UNIT 1U-3811-4 AC I/F UNIT F SCHEMATIC DIAGRAMS (13/17) 1 2 S-102 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (13/17) 1U-3811-1 D.AMP/SMPS UNIT (1/3) F SCHEMATIC DIAGRAMS (14/17) 1 2 S-102 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (14/17) 1U-3811-1 D.AMP/SMPS UNIT (2/3) F SCHEMATIC DIAGRAMS (15/17) 1 2 S-102 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (15/17) 1U-3811-1 D.AMP/SMPS UNIT (3/3) (for E2 model) F SCHEMATIC DIAGRAMS (16/17) 1 2 S-102 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (16/17) 1U-3811-1 D.AMP/SMPS UNIT (3/3) (for E3 model) F SCHEMATIC DIAGRAMS (17/17) 1 2 S-102 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (17/17) 1U-3811-1 D.AMP/SMPS UNIT (3/3) (for JP model) F ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- DVD Surround Receiver
- Sub Woofer
- Speaker System
- High-quality audio and video
- Immersive home entertainment experience
Frequently asked questions
The warranty period for the Denon S-102 DVD Home Entertainment System is 8 years from the date of manufacture.
If the Denon S-102 DVD Home Entertainment System does not read discs, you should check the laser drive current. If the laser drive current is more than 1.5 times the initial value, the Optical Pickup should be replaced.
To enter the test mode, press the "STOP" and "OPEN/CLOSE" buttons simultaneously while in the Aging mode. Not insert the disc. When the Aging mode is set, the "STOP" and "OPEN/CLOSE" indicators light.