null  null
140
106
BROOK
120
DST
LOW
WIND
MHz
170 x10kHZ
108
ALERT
SOUND
ON/SLEEP
iWB
WEATHER
RADIO ON/ SLEEP
RADIO
SNOOZE / DIMMER
WEATHER
100
OFF/R
ESET
Model T463
Weather Alert Alarm Clock Radio
with Nature Sounds
P
ON/SLEE
SOUND
D
80
100
FOREST
96
70
104
SUN MON TUE WED THU FRI SAT
M
ALARM
SET
ALERT
SOUND OFF
60
88 92
OCEAN
FM
AM 54
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.
This symbol is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature accompanying
the product.
These symbols are located on the back of the cabinet.
CAUTION: To prevent electric shock, match wide blade of
plug to wide slot. Fully insert.
ATTENTION: Pour éviter les choc électriques. Introduire la
lame la plus large de la fiche dans la borne correspondante
de la prises et pousser jusqu’au fond.
1
Table of Contents
A Consumer Guide to Product Safety ..............................................................................................3-4
FCC Information
Safety Instructions
Preparation for Use .....................................................................................................................................5
Maintenance
Battery Installation
DC Operation
Battery Low Indicator
Daylight Savings Time and LCD Indicators.............................................................................................6
Controls and Indicators .........................................................................................................................................7
Setting the Clock Time ..............................................................................................................................................8
Setting the Calendar .............................................................................................................................................9
Setting the Alarm Time ...................................................................................................................10-11
Listening to the Radio .............................................................................................................................................12
Listening to Nature Sounds ..................................................................................................................................13
Listening to Weather .............................................................................................................................................14
Sleep Timer Operation .........................................................................................................................................15
Weather Alert Operation..................................................................................................................16-17
Weather Alert with Built-Warning Phrase and Light
Weather Alert with Light Only
Snooze/Dimmer Operation....................................................................................................................................18
Warranty ......................................................................................................................................................19
A Consumer Guide to Product Safety
Important Radio FCC Information
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. There limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instruction, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is needed.
• Consult the dealer or an experienced radio/TV technician for help.
3
A Consumer Guide to Product Safety
IMPORTANT SAFETY INSTRUCTIONS
This unit has been designed and manufactured to assure your personal safety. Improper use can result in potential electrical shock or fire hazards. Please
read all safety and operating instructions carefully before installation and use. Keep these instructions handy for future reference. Take special note and
adhere to all warnings, any always follow the instructions on the unit and in the instruction and service manual.
1. Water and Moisture: The unit should not be used near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement,
or near a swimming pool, etc.
2. Ventilation: The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, it should not be
situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or placed in a built-in installation, such as bookcase or cabinet
that may impede the flow of air through the ventilation openings.
3. Heat: The unit should be situated away from heat source such as radiators, heat register, stoves, or other appliances (including
amplifiers) that produce heat.
4. Power Sources: The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the
appliance.
5. Grounding or Polarization: This product is equipped with a polarized alternating current line plug (a plug having one blade wider than
the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
6. Power Cord Protection: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against
them. It is always best to have a clear area from where the cord exits the unit to where it is plugged into an AC outlet.
7. Cleaning: The unit should be cleaned only as recommended by the manufacturer.
8. Non use Periods: The power cord of the unit should be unplugged from the outlet when it is to be left unused for a long period of time.
9. Object and Liquid Entry: Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.
10. Damage Requiring Service: The appliance should be serviced by qualified service personnel when:
A. The power-supply cord or plug has been damaged.
B. Objects have fallen into or liquid has been spilled into the enclosure.
C. The unit has been exposed to rain.
D. The unit has been dropped or the enclosure damaged.
E. The unit does not appear to operate normally or exhibits a marked change in performance.
11. Servicing: The user should not attempt to service the unit beyond that described in the user’s operating instructions. All other
servicing should be referred to qualified service personnel.
12. If you have any questions, call SDI Technologies Inc., Timex Audio Products Division Customer Service, 1-800-888-4491.
4
Preparation for Use
Preparation for Use
1. Remove the unit and all packing materials from the carton.
2. It is a good idea to save all the packing materials in case the unit ever needs to be returned for service. If you do dispose of the packing
materials, please do so properly.
3. Remove any feature labels, fact tags, or clear protective films from the front or top of the radio, if applicable. Do not remove any labels
from the back or bottom of the unit.
Maintenance
• Place the unit on the level surface away from sources of direct sunlight or excessive heat.
• Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should be
placed between the unit and the furniture.
• Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzine, thinner, or similar
materials can mark the surface of the case.
• In the remote case that the unit is not operating properly, please unplug the unit, re-install all batteries, and re-program all the settings.
Installation
light up.
Note: This Clock Radio operates on both AC or DC supply. When the unit is connected to AC power, the display back light will
Important:
To ensure that you will not miss the weather alert warning, we recommend the user to install the batteries even when using AC supply.
DC Operation
1. Gently turn the unit over and remove the battery compartment door.
2. Install 5 “AA” alkaline batteries while making sure that the polarity is correct as shown
inside compartment. For best performance and longer life, we recommend using
alkaline batteries.
3. Close the battery compartment door and gently turn the unit right side up.
Battery Low Indicator
LOW
When the batteries are getting weak, a Battery Low Icon ( ) will flash on the lower right side of the time digits. You should replace
the batteries.
Important:
Unit MUST be connected to the AC power while replacing the batteries otherwise, time and alarm settings may be lost.
5
Daylight Savings Time and Leap Years
M
D
DST
LOW
SUN MON TUE WED THU FRI SAT
Sleep Volume Indicators
ALERT
Steady Light:
Indicates that the
Weather Channel
is Being Broadcasted
Flashing Light:
Indicates the Weather
Alert Warning
Nature Sound Indicators
Battery Low Indicator
DST (Daylight Savings Time)
Wake To Alarm Sound
and Alarm On/Off Icons
LCD Indicators
This unit will automatically adjust the clock at the beginning and end of Daylight Savings time each year. It will also adjust the month/date
display for Leap Year automatically. This unit automatically advances by one hour at the start of Daylight Savings on the first Sunday of
April and automatically moves back by one hour at the end of Daylight Savings on the last Sunday of October. If you live in an area that
does not observe Daylight Savings, it will be necessary for you to manually adjust the clock back one hour at the beginning of Daylight
Savings and forward one hour at the end of Daylight Savings.
ALERT
Power On Indicator
PM Indicator
Clock Time
Month/Date
Audible Weather
Alert Off Indicator
Sleep Time
Day of Week
6
N
TIME SET.
CAL. SET
iWB
DAILY AL ARM
7-5-2
SLEE
P VO
L.
FWD BUT
TON
Radio On/Sleep Button
EP
ON/SLE
SOUND
WEATHER
100
140
106
BROOK
120
DST
LOW
WIND
MHz
170 x10kHZ
108
ALERT
SOUND
ON/SLEEP
iWB
RADIO ON/ SLEEP
RADIO
SN OOZE / DIMMER
WEATHER
80
100
FOREST
96
70
104
SUN MON TUE WED THU FRI SAT
M
ALARM
SET
ALERT
SOUND OFF
60
88 92
OCEAN
AM 54
FM
D
Controls and Indicators
Calendar Set
Button
FWD BUTTO
FWD
Button
7.5.2 Button
ON/SLEEP
ESET
Sleep Volume
Button
REV Button
SNOOZ E / DIMMER
OFF/R
Time Set Button
SOUND
Sound/On
Sleep Button
Snooze/Dimmer
Button
Alarm
Buttons
Weather
Channel
Switch
Test
Switch
Weather
Alert Sound
Switch
7
OFF/R
ESET
Instant Weather
On/Sleep Button
Alarm Off/Reset
Button
Volume Control
Tuning Switch
Band Switch
Sound Buttons
CAL. SET
DAILY ALARM
7-5-2
D
SLEEP VOL.
Setting the Clock Time
LOW
DST
TIME SET
FWD or REV
TIME SET
approximately 8 seconds to return to normal mode.
Note: You can also allow the display to flash for
• Press again to return the display to normal mode.
A ‘Beep’ sound will confirm that the time is set.
Step 3
• While the clock digits are flashing, press and hold
either button to set the correct time. Remember
to set the correct AM or PM. The PM Indicator
is located next to the Hour Digit. Press and hold
FWD or REV Button to rapidly advance the
setting of time.
Step 2
• Press and hold until the clock digits begin flashing.
Step 1
flashing with a ‘Beep’ sound and return to normal mode. If this happens, you must follow the instructions again from Step 1.
Important: While setting the time or calendar, if you do not press the appropriate buttons within 8 seconds, the display will stop
TIME SET
PM Indicator
M
SUN MON TUE WED THU FRI SAT
8
D
DST
LOW
SUN MON TUE WED THU FRI SAT
M
Date
TIME SET
SOUND ON/SLEEP
TIME SET
Setting the Calendar
CAL. SET
DAILY ALARM
7-5-2
iWB
RADIO ON/SLEEP
SNOOZE / DIMMER
CAL. SET
DAILY ALARM
7-5-2
iWB
RADIO ON/SLEEP
SLEEP VOL.
OFF/RESET
SLEEP VOL.
OFF/RESET
Month
to set
Step 3
week is
Step 4
CALENDAR SET
FWD or REV
Note: You can also allow the display to flash for
approximately 8 seconds to return to normal mode
• Press to return to the normal mode. A ‘Beep’
sound will confirm that the calendar is set.
CALENDAR SET
• While the Calendar digits are flashing, press
repeatedly until the correct day of the
flashing on the display.
7.5.2
• While the Calendar digits are flashing, press
FWD to set the correct month and REV
the correct date.
Step 2
• Press and hold until the Month/Date Display
begin flashing.
Step 1
Important: While setting the time or calendar, if you do not press the appropriate buttons within 8 seconds, the display will stop
flashing with a ‘Beep’ sound and return to normal mode. If this happens, you must follow the instructions again from Step 1.
Day of
The Week
SOUND ON/SLEEP
SNOOZE / DIMMER
9
RADIO
WEATHER
ALERT
SOUND
LOW
DST
WIND
SLEEP VOL.
OFF/RESET
Wake To Alarm
Sound Icon
Setting the Alarm Time
Step 1
Alarm Set
FWD or REV
• Press button, the Wake Weather Alarm Icon
( Weather) and clock digits will flash. You may
choose to set any of the 3 alarms by simply pressing
the Alarm Set Button repeatedly until the desired
Wake to Alarm Sound Icon is displayed. Once
you have selected your wake to mode, proceed to
Step 2.
Note: The fourth time the button is pressed, the
display will return to normal mode with a ‘Beep’ sound.
Step 2
7.5.2
• While the clock digits and desired Wake to Alarm
Sound Icon are flashing, press FWD or REV Button
to set the alarm time. Remember to set the correct
AM or PM. The PM indicator is located next to the
Hour Digit. Press and hold FWD or REV Button to
rapidly advance the setting of time.
Step 3
(Continue on next page.)
Important: While setting the alarm times, if you do not press the appropriate buttons within 8 seconds, the display will stop flashing
and will beep. If this happens you must press the Alarm Set Button once to enter the Setting Mode.
D
BROOK
RADIO ON/SLEEP
iWB
DAILY ALARM
7-5-2
CAL. SET
FOREST
SUN MON TUE WED THU FRI SAT
M
LOW
ALARM
SET
ALERT
SOUND OFF
ALERT
OCEAN
TIME SET
SOUND ON/SLEEP
SNOOZE / DIMMER
• Press repeatedly until the amount of days you would
like the alarm to be set for appears on the bottom
of display.
7: Full week (Monday through Sunday)
5: Weekdays (Monday through Friday)
2: Weekends (Sunday and Saturday)
Note: Repeat Step 1 to 3 to set the rest of Alarms
if needed.
10
RADIO
(Continued from previous page.)
D
FOREST
WEATHER
BROOK
Wake To Alarm
Sound Icon
Step 5
ALARM SET
• Press all or any of 3 to select the alarm sound(s)
you wish to wake to. The Wake to Alarm Sound
Icon will appear on the top of the display.
(Alarm ON/OFF buttons)
WEATHER, RADIO
& SOUND
• Press until the display returns to normal mode
with a ‘Beep’ sound. You can also allow the
display to flash for approximately 8
seconds to
return to normal mode.
Step 4
Setting the Alarm Time
ALERT
SOUND
DST
LOW
WIND
SUN MON TUE WED THU FRI SAT
M
LOW
ALARM
SET
ALERT
SOUND OFF
ALERT
OCEAN
Note: You may confirm your alarm setting(s) at
any time by pressing WEATHER, RADIO, and/or
SOUND Button(s), the corresponding alarm time
and amount of days (7.5.2) you have previously
set will appear on the display for approximately
8 seconds.
Note:
• For ‘Wake to Radio Alarm’, DO NOT FORGET to set the radio station and volume level you wish to wake to.
• For ‘Wake to Nature Sounds Alarm’, the last nature sound that you listened to will be the nature sound that is set for the alarm.
• You can wake to 3 different alarm times by setting different wake up times for the Weather, Radio and/or Nature Sounds. To activate
all or any of the 3 alarms, simply press the Weather, Radio, and/or Sound (Alarm ON/OFF Buttons).
• To cancel any of the Weather, Radio, Nature Sounds alarm(s) simply press the Weather, Radio and/or Sound Button(s) repeatedly
until the Wake to Alarm Sound Icon(s) disappear from the top of display.
• When the unit is not using AC and batteries are weak, the alarm will default to piezo buzzer.
• After the alarm turns on, press the Off/Reset Button to turn off the alarm. The alarm will come on again the following day unless the
controls are changed. If the alarm is not turned off after it sounds, it will play for approximately 1 hour and reset itself automatically for
the following day.
11
CAL. SET
DAILY ALARM
7-5-2
iWB
RADIO ON/SLEEP
OFF/RESET
SLEEP VOL.
Listening to Radio
RADIO ON/SLEEP
BAND
TUNING & VOLUME
OFF/RESET
• Press to turn the power off.
Step 4
• Tune to your favorite station and adjust volume.
(located on the right side of unit)
Step 3
• Slide to select AM or FM.
(located on the right side of unit)
Step 2
• Press once to turn radio on. The Dial Pointer
Indicator will light up for easy night time tuning.
Step 1
Note: This unit has a built-in FM Line Cord Antenna. For best FM reception, try varying the position of the AC Cord. Rotate the unit,
as required, for best AM reception.
TIME SET
SOUND ON/SLEEP
SNOOZE / DIMMER
12
TIME SET
SOUND ON/SLEEP
TIME SET
SOUND ON/SLEEP
CAL. SET
DAILY ALARM
7-5-2
iWB
RADIO ON/SLEEP
SNOOZE / DIMMER
CAL. SET
DAILY ALARM
7-5-2
iWB
RADIO ON/SLEEP
SNOOZE / DIMMER
SLEEP VOL.
OFF/RESET
SLEEP VOL.
OFF/RESET
RADIO
WEATHER
BROOK
DST
LOW
WIND
ALERT
SOUND
Step 2
SOUND ON/SLEEP
VOLUME
OFF/RESET
• Press to turn the power off.
Step 4
• Rotate to adjust desired volume level.
(located on the right side of unit)
Step 3
• Press to select desired Nature Sound.
OCEAN, FOREST,
BROOK, WIND
• Press once to listen to Nature Sounds.
Step 1
Listening to Nature Sounds
D
FOREST
SUN MON TUE WED THU FRI SAT
M
LOW
ALARM
SET
ALERT
SOUND OFF
ALERT
OCEAN
13
CAL. SET
DAILY ALARM
7-5-2
iWB
RADIO ON/SLEEP
SNOOZE / DIMMER
CAL. SET
DAILY ALARM
7-5-2
iWB
RADIO ON/SLEEP
SLEEP VOL.
OFF/RESET
SLEEP VOL.
OFF/RESET
ALARM
SET
LOW
M
RADIO
FOREST
ALERT
SOUND
LOW
DST
WIND
IWB/Weather
Alert Indicator
INSTANT WEATHER
ON/SLEEP
WEATHER CHANNEL
VOLUME
5: 162.500 MHz
6: 162.525 MHz
7: 162.550 MHz
OFF/RESET
• Press to turn the power off.
Step 4
• Rotate to adjust desired volume level.
(located on the right side of unit)
Step 3
1: 162.400 MHz
2: 162.425 MHz
3: 162.450 MHz
4: 162.475 MHz
• Set to the number position that has the best
reception in your living area.
(located on the left side of unit)
Step 2
• Press once to listen to Weather. The green
IWB/Weather Alert Indicator will stay on as
long as the unit is at Weather Channel.
Step 1
Listening to Weather
WEATHER
BROOK
SUN MON TUE WED THU FRI SAT
OCEAN
SOUND OFF
ALERT
ALERT
D
Note: Extend the external wire antenna fully for best reception.
TIME SET
SOUND ON/SLEEP
TIME SET
SOUND ON/SLEEP
SNOOZE / DIMMER
14
LOW
DST
ALERT
SLEEP
Sleep Volume
Indicator
SLEEP VOLUME
TIME SET
SOUND ON/SLEEP
CAL. SET
DAILY ALARM
7-5-2
iWB
RADIO ON/SLEEP
SNOOZE / DIMMER
SLEEP VOL.
OFF/RESET
OFF/RESET
Radio On/
Sleep
• Press at any time to turn off the Radio, Nature
Sounds, or Weather before the sleep timer
has elapsed.
Step 3
Sound On/
Sleep
IWB/Weather On/
Sleep
NOTE: The Sleep Volume will not affect the wake
up volume level.
SLEEP
• Press repeatedly until desired Sleep Volume Level
is set. The Sleep Volume Icon ( ) will appear
on the display.
Step 2
Sleep Timer Operation
Step 1 IWB WEATHER ON/SLEEP
RADIO ON/SLEEP
SOUND ON/SLEEP
90 min
15 min
D
SUN MON TUE WED THU FRI SAT
M
• Press any of the 3 above buttons once for power.
Press a second time to enter the 90 Minute Sleep
Timer Mode or repeatedly until desired Sleep Time
is set. The sleep duration changes as follows:
Radio
Nature Sounds ON
IWB Weather
60 min
30 min
Radio
Nature Sounds OFF
Weather
ALERT
Sleep Timer
15
Weather Alert Operation
Important Information Regarding Weather Broadcasts
• Weather band broadcast transmission has very low power and is not the same as the transmission of FM radio broadcasts.
• Weather band stations are located in the specific geographic locations and terrain, which means the area in which you live may not be within the range
of such a station. If you receive AM and FM stations without a problem but cannot receive Weather Band information, it means you are beyond the
range of the nearest weather station, not that your radio is defective.
• To help improve reception, move the antenna or rotate the radio until you get the best reception. Reception will also vary from day time to night time.
M
D
DST
LOW
SUN MON TUE WED THU FRI SAT
Beep...Beep...
WEATHER ALERT!
TUNE TO YOUR
WEATHER BAND
STATION!
IWB/Weather
Alert Indicator
(Continue on next page.)
• Press to listen to the Weather Broadcast when the
built-in warning phrase is heard and when the
IWB Weather Alert Indicator is flashing.
Step 4 INSTANT WEATHER
ON/SLEEP
ALERT
This unit includes special weather alert circuitry designed to receive the emergency broadcast signal from the N.O.A.A.. If severe or
dangerous weather conditions are approaching your area, your local N.O.A.A. station wil send out an alert signal which will be picked
up by this unit. When the radio receives the alert signal, it will warn you with a flashing green LED (on the right side of display) and/or
built-in warning phrase. This weather alert circuitry will override all other operations.
WEATHER ALERT SOUND
ALERT
• Weather Alert (with built-in warning phrase and light)
Step 1
(located on the left side of unit)
TEST
• Slide to ON position.
Step 2
TEST
• Press for 3 seconds. The green Weather Alert LED
(on the right side of display) will flash and the built-in
warning phrase will be heard.
Step 3
• Press again to cancel the test.
NOTE: When the unit is set to receive the alert signal,
it will warn you with a flashing green LED (on the right
side of display) and a built-in warning phrase will be
announced 3 times. In the case that you had missed the
built-in warning phrase, periodically check to see for the
flashing Weather Alert Indicator.
16
(Continued from previous page.)
M
TEST
D
DST
LOW
SUN MON TUE WED THU FRI SAT
Weather Alert
Indicator
ALERT
• Press to listen to the Weather Broadcast when the
built-in warning phrase is heard and when the
IWB Weather Alert Indicator is flashing.
Step 4 INSTANT WEATHER
ON/SLEEP
• Press again to cancel the test.
Step 3
Weather Alert Operation
WEATHER ALERT SOUND
• Weather Alert (with light only)
Step 1
• Slide to OFF position. The red LED (on the left side of
display) will light up indicating that the audible warning
phrase will NOT be heard when an emergency
broadcast signal is received.
TEST
NOTE: When the radio receives the alert signal, it will
however, warn you with a flashing green LED (on the
right side of display).
Step 2
• Press for 3 seconds. The green Weather Alert LED
(on the right side of display) will flash.
ALERT
No Audible
Warning Indicator
NOTES:
• Your local N.O.A.A. weather broadcast station will transmit a weather alert signal each week on Wednesday between 10:00 a.m. and
12:00 noon local time so that you can verify your radio is working properly. (Exception: If severe weather is predicted during the normal
testing time, the test may be delayed to the following day.)
• Your weather alert radio will react to the above test signal the same way it will for an actual emergency broadcast signal. Depending
on the setting of the Weather Alert Sound Switch, when the test alert signal is received, the green Weather Alert LED will flash
and/or warning phrase will be heard together.
17
Snooze / Dimmer Operation
• Press the Snooze/Dimmer Button repeatedly to change the brightness of the display back light. There are 3 levels of brightness under
AC operation. During the DC operation, pressing the Snooze/Dimmer button will light the display for 5 seconds.
CAL. SET
DAILY ALARM
7-5-2
iWB
RADIO ON/SLEEP
SLEEP VOL.
OFF/RESET
Snooze/Dimmer
• Press the Snooze/Dimmer Button after the alarm sounds. The alarm will turn off then come back on again in approximately 9 minutes.
You may repeat this cycle several times during the 1 hour alarm cycle.
TIME SET
SOUND ON/SLEEP
SNOOZE / DIMMER
18
Limited 90-Day Warranty Information
Timex Audio Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product
to be free from defects in workmanship and materials, under normal use and conditions, for a period of 90 days from the
date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.
Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty
period, SDI Technologies will repair or, at its discretion, replace this product without charge (except for a $3.00 charge for
handling, packing, return UPS/postage, and insurance). This decision is subject to verification of the defect or malfunction
upon delivery of this product to the Factory Service Center listed below. The product must include proof of purchase, including
date of purchase. The fee for service after the warranty period or without proof of purchase is $6.00.
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or
defective batteries are the most common cause of problems encountered.
If service is still required:
1. Remove batteries (if applicable) and pack the unit in a well-padded, heavy corrugated box.
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase.
3. Enclose a check or money order payable to the order of Soundesign, for the sum of $3.00 (or $6.00 if after the warranty
period or without proof of purchase).
4. Send the unit prepaid to the Factory Service Center listed below:
Consumer Repair Department
SDI Technologies Inc.
Timex Audio Products Division
1401 Pullman Drive, Suite A
El Paso, TX 79936-7726
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i)
products which have been damaged by negligence, misuse or accident, or which have been modified or repaired by
unauthorized persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to tape cassettes
(if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the product subsequent to
the original purchaser. Any applicable implied warranties are also limited to 90 days, and SDI Technologies will not be liable
for consequential damages. (Some states do not allow limitations on implied warranties or exclusion of consequential
damages, so these restrictions may not apply to you.) This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
For questions or comments regarding this or other products, please call our toll-free number: 1-800-888-4491.
TIMEX is a registered trademark of Timex Corporation in the United States and other countries.
T231-011204-0
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement