Mechanic Motor Vehicle - Directorate General of Employment

Mechanic Motor Vehicle - Directorate General of Employment
SYLLABUS OF SEMESTER SYSTEM
FOR THE TRADE OF
Mechanic Motor Vehicle
Under
Craftsmen Training Scheme (CTS)
(Two years/Four Semesters)
Redesigned in
2014
By
Government of India
Ministry of Labour & Employment (DGE&T)
1
GENERAL INFORMATION
1.
Name of the Trade
:
Mechanic Motor Vehicle
2.
N.C.O. & NOS Code No. :
7231.10, ASC/ Q 1401, ASC/ Q 1402
3.
Duration of Craftsmen
Training
:
2 Year (Four Semester having duration of six months each)
4.
5.
Power Norms
Space Norms
:
:
4.8 KW
Space Area 210 Sq. Mt. (Including parking area)
6.
Entry Qualification
:
Passed 10th class examination with maths and Science.
7.
Unit strength
:
16 + 30% super Numeric
8.
Instructors
Qualification
: a) Degree in Automobile/ Mechanical Engg. (with specialization in
Automobile) from recognised college/University with one year
experience in the automobile industry and should possess valid LMV
driving license.
OR
Diploma in Automobile/Mechanical (specialization in automobile)
from recognized board of technical education with two years
experience in the automobile industry and should posses valid
LMV driving license.
OR
10th Passed + NTC/NAC in the Trade of “Mechanic
Motor Vehicle)” with 3 years post qualification experience in
the relevant field and should possess valid LMV driving license.
and
b) With “National Crafts Instructor Certificate”.
* Note:
1) At least one Instructor must have Degree/Diploma in
Automobile/ Mechanical Engg. (with specialization in
Automobile) when applied for 02 units.
2) Instructor Qualification for WCS & E.D, as per the Training
Manual
2
9. For Employability Skills One Contract/Part Time/Guest Faculty for Generic Module .
i) MBA/ BBA with two years experience OR Graduate in Sociology / Social
Welfare / Economics with Two years experience OR Graduate / Diploma with
Two years experience and trained in Employability Skills from DGET institutes
AND
Must have studied English / Communication Skills and Basic Computer at 12th /
Diploma level and above
OR
Existing Social Study Instructors duly trained in Employability Skills from DGET
institutes
Distribution of training on Hourly basis:
Total hours
/week
Trade practical
Trade
theory
42 Hours
27 Hours
5 Hours
Work
shop Cal.
&Sc.
3 Hours
3
Engg.
Drawing
Employability
skills
Extracurricular
activity
3 Hours
2 Hours
2 Hours
COURSE INFORMATION (MECHANIC MOTOR VEHICLE)
1.Introduction :
 An intensive industrial survey was made to ascertain the requirements of
skill-gap in the automobile sector; a scientifically designed survey covering
labour-market survey web-survey was conducted. Based on the data
obtained, the skills are identified and accordingly the syllabus has been
drafted. Subsequently the Trade expert committee reviewed.
2. Terminal Competencies/Deliverables:
After successful completion of the above course, the trainee shall be able to perform
the following skills with proper sequence.

Mechanic, Automobile repairs overhauls and services motor vehicles to keep them in
good running condition.

Examines vehicle to ascertain nature and location of defects either by running engine
or driving vehicle on road.

Dismantles partially or completely defective unit or parts of vehicle such as engine,
gear box, rear axle, front axle, steering assembly, radiator, etc. according to nature of
repairs to be done, using hoist, jack, pullers, hand tools and other devices.

Measures essential parts like cylinder, bores piston, sizes crank pins etc. using gauges,
micrometer and other precision tools and gets cylinders rebored, liners filled, valve
seats refaced, bearings replaced etc. as necessary.

Repairs or overhauls and assembles engine such as replacing defective parts,
scrapping bearings, setting timing, cleaning injectors, tuning carburettor etc.
according to maker's specification.

Replaces or repairs defective parts of gear box, rear axle, steering mechanism etc. and
sets them right ensuring correct alignment, clearance, meshing of gears, specified
movements and operations.

Relines and builds brakes, sets wheel alignment, adjust, steering, clutch, hand brakes
etc fits new or repaired accessories and body parts, makes electrical connection, and
performs other tasks to effect repairs.

Lubricates, joints, tightens loose parts, tests performance of vehicle by driving on road
and makes necessary adjustments to attain desired standard.
4
3. Employment opportunities:
On successful completion of the course the candidates can either get employed, or
become a self-employed Entrepreneur in any one of the following fields.
a) Wage Employment
1. Auto Mechanic
2. Vehicle Service Technician
3. Auto Fitter in Manufacturing Concern in
Assembly Shop or Test Shop
4. Mechanic in Auto Manufacturing Industry
5. Dealers service mechanic
6. Driver/Vehicle Operator
7. Spare Parts Sales Assistant /
Manufacturers' Representative
8. Laboratory Assistant
9. Auto Electrician
b) Self Employment
1. Automobile Mechanic
2.. Diesel Fuel System Service Mechanic
3. Vehicle Operator
4. Spare Parts Salesman
5. Spare Parts Dealer
4. Further learning pathways:
 On successful completion of the course trainee can get themselves enrolled in
Apprenticeship training in reputed Industrial organisation.
 The qualified candidates have scope for lateral entry into the Diploma courses offered
by some of the State Governments
 The qualified candidates can also get themselves upgraded by taking up the Second
Semester at his own convenience in the CTS scheme, since the first semester is
common to the following trades.
Craftsman Training Scheme
1.
2.
3.
4.
5.
6.
7.
Mechanic Motor Vehicle
- 2 Years ( 4 Sem)
Mechanic Diesel
– 1 Year ( 2 Sem)
Mechanic Motor Cycle
- 1 Year ( 2 Sem)
Mechanic Auto Electrical and Electronics - 1 Year ( 2 Sem)
Mechanic Agricultural Machinery
- 2 Years ( 4 Sem)
Mechanic Tractor
- 1 Year ( 2 Sem)
Pump Operator cum Mechanic
- 1 Year ( 2 Sem)
5
Syllabus for the trade of Mechanic Motor Vehicle
First Semester (Semester code No.
)
Duration: Six Months.
Syllabus for Trade practical and Trade Theory
Trade Practical (27 Hrs/week)
Trade Theory (5 Hrs/week)
Week
No.
1
Familiarisation with institute, Job Admission & introduction to the trade:
opportunities in the automobile Introduction to the Course duration, course
sector, Machinery used in Trade. content, study of the syllabus. General rule
Types of work done by the students pertaining to the Institute, facilities available–
Hostel, Recreation, Medical and Library working
in the shop floor.
hours and time table
2
Practical related to Safety and Occupational Safety & Health
Importance
of
Safety
and
general
Health,
Precautions
to
be
observed
in
the
shop.
Basic
Importance of maintenance and
first aid, safety signs - for Danger, Warning,
cleanliness of Workshop.
caution & personal safety message. Safe handling
Interaction with health centre and
of Fuel Spillage, Fire extinguishers used for
fire service station to provide demo different types of fire. Safe disposal of toxic dust,
on First aid and Fire safety, Use of safe handling and Periodic testing of lifting
fire extinguishers.
equipment, Authorization of Moving & road
Demonstration on safe handling and testing vehicles.
Periodic testing of lifting equipment, Energy conservation-Definition, Energy
and Safety disposal of Used engine Conservation Opportunities (ECOs)-Minor ECos
and Medium ECOs, Major ECOs), Safety disposal
oil.
Energy saving Tips of ITI electricity of Used engine oil, Electrical safety tips.
Usage
3-5
Practice using all marking aids, like Hand & Power Tools:steel rule with spring calipers, Marking scheme, Marking material-chalk,
dividers, scriber, punches, Chisel Prussian blue. Cleaning tools- Scraper, wire brush,
Emery paper, Description, care and use of Surface
etc.,
plates, steel rule, measuring tape, try square.
Layout a work piece- for line, circle,
Calipers-inside and outside. Dividers, surface
arcs and circles.
gauges, scriber, punches-prick punch, center punch,
Practice to measure a wheel base of a pin punch, hollow punch, number and letter punch.
vehicle with measuring tape.
Chisel-flat, cross-cut. Hammer- ball pein, lump,
Practice to measure valve spring mallet. Screw drivers-blade screwdriver, Phillips
screw driver, Ratchet screwdriver. Allen key, bench
tension using spring tension tester
Practice to remove wheel lug nuts vice & C-clamps, Spanners- ring spanner, open
end spanner & the combination spanner,
with use of an air impact wrench
universal adjustable open end spanner. Sockets &
Practice on General workshop tools accessories, Pliers - Combination pliers, multi
& power tools.
grip, long nose, flat-nose, Nippers or pincer
pliers, Side cutters, Tin snips, Circlip pliers,
external circlips pliers. Air impact wrench, air
ratchet, wrenches- Torque wrenches, pipe
wrenches, car jet washers Pipe flaring & cutting
tool, pullers-Gear and bearing.
6
6&7
8&9
Measuring practice on Cam height,
Camshaft Journal dia, crankshaft
journal dia, Valve stem dia, piston
diameter, and piston pin dia with
outside Micrometers.
Measuring practice on the height of
the rotor of an oil pump from the
surface of the housing or any other
auto component measurement with
depth micrometer.
Measuring practice on valve spring
free length.
Measuring practice on cylinder bore,
Connecting rod bore, inside diameter
(ID) of a camshaft bearing with
Telescope gauges.
Measuring practice on cylinder bore
for taper and out-of-round with Dial
bore gauges.
Measuring practice to measure wear
on crankshaft end play, crankshaft
run out, and valve guide with dial
indicator.
Measuring practice to check the
flatness of the cylinder head is
warped or twisted with straightedge
is used with a feeler gauge.
Measuring practice to check the end
gap of a piston ring, piston-tocylinder wall clearance with feeler
gauge.
Practice to check engine manifold
vacuum with vacuum gauge.
Practice to check the air pressure
inside the vehicle tires is maintained
at the recommended setting.
Practice on General cleaning,
checking and use of nut, bolts, &
studs etc.,
Removal of stud/bolt from blind
hole.
Practice on cutting tools like
Hacksaw, file, chisel, Sharpening of
Chisels, center punch, safety
precautions while grinding.
Systems of measurement, Description, care &
use of - Micrometers- Outside and depth
mirometer, Micrometer adjustments,
Vernier
calipers, Telescope gauges, Dial bore gauges, Dial
indicators, straightedge, feeler gauge, thread pitch
gauge, vacuum gauge, tire pressure gauge.
Fasteners- Study of different types of screws,
nuts, studs & bolts, locking devices, Such as lock
nuts, cotter, split pins, keys, circlips, lock rings,
lock washers and locating where they are used.
Washers & chemical compounds can be used to
help secure these fasteners. Function of Gaskets,
Selection of materials for gaskets and packing, oil
seals.
Cutting tools :- Study of different type of cutting
tools like Hacksaw, File- Definition, parts of a
7
Practice on Hacksawing and filing to
given dimensions.
10 &
11
12
13
14
Practice on Marking and Drilling
clear and Blind Holes, Sharpening of
Twist Drills Safety precautions to be
observed while using a drilling
machine. Practice on Tapping a
Clear and Blind Hole, Selection of
tape drill Size, use of Lubrication,
Use of stud extractor.
Cutting Threads on a Bolt/ Stud.
Adjustment of two piece Die,
Reaming a hole/ Bush to suit the
given pin/ shaft, scraping a given
machined surface.
Practice on making Rectangular
Tray.
Pipe bending, Fitting nipples unions
in pipes. Soldering and Brazing of
Pipes.
Practice in joining wires using
soldering Iron, Construction of
simple electrical circuits, Measuring
of current, voltage and resistance
using digital multimeter, practice
continuity test for fuses, jumper
wires, fusible links, circuit breakers.
Diagnose series, parallel, seriesparallel circuits using Ohm’s law,
Check electrical circuit with a test
lamp, perform voltage drop test in
circuits using multimeter, measure
current flow using multimeter
/ammeter, use of service manual
wiring diagram for troubleshooting.
file, specification, Grade, shape, different type of
cut and uses., OFF-hand grinding with sander,
bench and pedestal grinders, safety precautions
while grinding.
Limits, Fits & Tolerances:-Definition of limits,
fits & tolerances with examples used in auto
components
Drilling machine - Description and study of
Bench type Drilling machine, Portable electrical
Drilling machine, drill holding devices, Work
Holding devices, Drill bits.
Taps and Dies: Hand Taps and wrenches,
Calculation of Tap drill sizes for metric and inch
taps. Different type of Die and Die stock. Screw
extractors. Hand Reamers – Different Type of
hand reamers, Drill size for reaming, Lapping,
Lapping abrasives, type of Laps.
Sheet metal - State the various common metal
Sheets used in Sheet Metal shop
Sheet metal operations - Shearing, bending,
Drawing, Squeezing
Sheet metal joints - Hem & Seam Joints Fastening
Methods - Riveting, soldering, Brazing. fluxes
used on common joints. Sheet and wire-gauges.
The blow lamp- its uses and pipe fittings.
Basic electricity, Electricity principles, Ground
connections, Ohm's law, Voltage, Current,
Resistance, Power, Energy. Voltmeter, ammeter,
Ohmmeter Mulitmeter, Conductors & insulators,
Wires, Shielding, Length vs. resistance, Resistor
ratings
Fuses & circuit breakers, Ballast resistor,
Stripping wire insulation, cable colour codes and
sizes, Resistors in
Series circuits , Parallel
circuits and Series-parallel circuits, Electrostatic
effects, Capacitors and its applications, Capacitors
in
series
and
parallel.
8
15
16
17&
18
Cleaning and topping up of a lead
acid
battery, Testing battery with
hydrometer,
Connecting battery to a charger for
battery charging, Inspecting &
testing a battery after charging,
Measure and Diagnose the cause(s)
of excessive Key-off battery drain
(parasitic draw) and do corrective
action. Testing of relay and solenoids
and its circuit.
Identify and test power and signal
connectors for continuity, Identify
and test different type of Diodes,
NPN & PNP Transistors for its
functionality,
Construct and test simple logic
circuits OR, AND & NOT and Logic
gates using switches.
Practice to make straight beads and
Butt, Lap & T joints Manual Metal
Arc Welding.
Setting of Gas welding flames,
practice to make a straight beads and
joints Oxy – Acetylene welding
Film on Heat treatment process
19 &
20
Practice on Liquid penetrant testing
method and Magnetic particle testing
method.
Identification of Hydraulic and
pneumatic components used in
vehicle.
Tracing of hydraulic circuit on
hydraulic jack, hydraulic power
steering,
and
Brake
circuit.
Description of Chemical effects, Batteries &
cells, Lead acid batteries & Stay Maintenance
Free (SMF) batteries, Magnetic effects, Heating
effects, Thermo-electric energy, Thermisters,
Thermo couples, Electrochemical energy, Photovoltaic
energy,
Piezo-electric
energy,
Electromagnetic induction, Relays, Solenoids,
Primary & Secondary windings, Transformers,
stator and rotor coils.
Basic electronics: Description of
Semi
conductors, Solid state devices- Diodes,
Transistors, Thyristors, Uni Junction Transistors (
UJT), Metal Oxide Field Effect Transistors (
MOSFETs), Logic gates-OR, AND & NOT and
Logic gates using switches.
Introduction to welding and Heat Treatment
Welding processes – Principles of Arc welding, brief
description, classification and applications. Manual
Metal Arc welding -principles, power sources,
electrodes, welding parameters, edge preparation
& fit up and welding techniques; Oxy – Acetylene
welding - principles, equipment, welding
parameters, edge preparation & fit up and welding
techniques;.
Heat Treatment Process– Introduction, Definition
of heat treatment, Definition of Annealing,
Normalizing, Hardening and tempering. Case
hardening, Nitriding, Induction hardening and
Flame Hardening process used in auto
components with examples.
Non-destructive Testing Methods- Importance
of Non-Destructive Testing In Automotive
Industry, Definition of NDT, Liquid penetrant
and Magnetic particle testing method – Portable
Yoke method
Introduction to Hydraulics & Pneumatics: Definition of Pascal law, pressure, Force,
viscosity. Description, symbols and application in
automobile of Gear pump-Internal & External,
9
21
22-23
24-25
26
Identification of components in Air single acting, double acting & Double ended
brake systems.
cylinder; Directional control valves-2/2, 3/2, 4/2,
4/3 way valve, Pressure relief valve, Non return
valve, Flow control valve used in automobile.
Pneumatic Symbols, Description and function of
air Reciprocating Compressor. Function of Air
service unit (FRL-Filter, Regulator & Lubricator).
Identification of different type of Auto Industry - History, leading manufacturers,
development in automobile industry, trends, new
Vehicle.
Demonstration
of
vehicle product. Brief about Ministry of Road transport &
Highways,
specification data;
The Automotive Research Association of India
Identification of vehicle information (ARAI), National Automotive Testing and R&D
Number (VIN). Demonstration of Infrastructure Project (NATRIP), & Automobile
Garage, Service station equipments.- Association.
Vehicle hoists – Two post and four Definition: - Classification of vehicles on the
post hoist, Engine hoists, Jacks, basis of load as per central motor vehicle rule,
Stands.
wheels, final drive, and fuel used, axles, position
of engine and steering transmission, body and
load. Brief description and uses of Vehicle hoists
– Two post and four post hoist, Engine hoists,
Jacks, Stands.
In-plant Training
Revision and Test
NCVT Exam
10
Workshop Calculation and Science
Syllabus for the trade of
1. Mechanic Motor Vehicle
Week
No.
1
2
3
4&5
6
7
8
9-10
11
12
13
14-15
16
17
18-19
20-21
Workshop calculation and
Science (3 Hrs/week)
1st Semester
Units, Derived and fundamental, types of system FPS, CGS, MKS and their conversion.
Metric weights and measurements, units conversion factors
Fractions- Addition and subtraction, Fractions and whole numbers, Combined addition
and subtraction, Multiplication and division of fractions. Operations in problems
involving fractions.
Order of performing (BODMAS) Mathematical operators , Integers – Rules for dealing
with integers, Addition, subtraction, Multiplication and division.
Ratio and proportion. Percentages, Examples of ratios in Automotive technology
. profit and loss, Discount .
simple interest and compound interest
depreciation calculation
Time and work problem , Time and distance, clocks and calendar,
Brief description of manufacturing process of steel, and aluminum
Meaning of elasticity, malleability, brittleness, hardness, compressibility & ductility and
their examples , Properties and uses of cast iron, ferrous metal, gray cast iron, white cast
iron, wrought iron, and plain carbon steel, high speed steel and alloy steel.
Properties and uses in automobile industries- copper, zinc, lead, tin, aluminum, brass,
bronze, solder bearing metals, timber and rubber. Nylon, P.V.C., PP (poly prop line,
polymer).
Materials – Stress, strain,- Definition of Stress, Types of stress- Tensile, compressive,
shear , Examples of the three basic stresses in automotive components , calculation of
stress and strain in automotive application, Stress raisers, Strain-, Tensile, compressive,
Shear strain, Tensile strength, Factor of safety, Torsional stress, Strain energy.
Definition of cold working and Hot working and its properties on sheet metal. Advantage
of Deep drawing material. Importance of Iron- carbon diagram in heat treatment process.
Different Type of cutting fluids and their properties. Calculation of cutting speed, feed
and drilling time.
Forces – Definition of Force, Types of force -examples,– Direct forces, Attractive
forces, Explosive forces, Describing forces, Graphical representation of a force,
Addition of forces, Parallelogram of forces ,Triangle of forces, Resolution of forces,
Mass, Equilibrium, Pressure, Pressure in hydraulic systems, Hooke’s law, Practical
applications.
Work energy, power– Definition and calculation of Work, Power and Work done by a
torque, Definition and calculation of Energy -Potential energy, Chemical energy,
Conservation of energy, Energy equation, Kinetic energy, Energy of a falling body,
Kinetic energy of rotation.
11
Week
No.
1
2&3
Syllabus for Engineering Drawing- Ist Semester
Syllabus for the trade of
1. Mechanic Motor Vehicle
Engineering Drawing (3 Hrs/week)
1st Semester
Importance of engineering drawing as a communication medium, different types of
drawing - Machine Drawing, Production Drawing, Part Drawing, Assembly
Drawing, Drawing instruments, equipment and materials and their uses
Scales - Recommended scales, reduced & enlarged Drawing Sheet sizes: A0, A1,
A2, A3, A4, A5, Layout of drawing sheet, sizes of title block and its contents. Using
drawing instruments to draw straight lines, rectangles, squares, circles, polygons.
4&5
Lettering and Dimensioning - Types of Lettering, Guide Lines for lettering,
Recommended sizes of letters and numbers, Single stroke letters, Dimensioning rules and systems of dimensioning – dimensioning a given drawing.
6&7
Identify the alphabet of lines- Read and Interpret the meaning of various line types
with examples- Object Lines, Hidden Lines, Center Lines, Phantom Lines,
Dimension Lines, Extension Lines, Leaders, Break Lines -Long-break Line, Round,
Solid, Hollow Cross Section, Section Lines – Common Manufacturing Materials,
Cutting Plane Lines
8-11
Geometric Construction - Bisecting a line - perpendiculars - parallel lines - division
of a line; Angles - bisection, trisection, Tangent lines touching circles internally and
externally Polygons - Regular polygons - circumscribed and inscribed in circles.
Conic sections - Definitions of focus, directrix, eccentricity, Construction of Ellipse
by Concentric circles method, Construction of parabola by rectangular method.
12&13 Orthographic Projection - Definition - Planes of Projection - Four quadrants –
Reference Line, First angle projection - Third angle projection.
14-17 Isometric Projection - Definition - Isometric axes, lines and planes, Isometric Scale Isometric view. Drawing of isometric views of plane figures, Drawing of isometric
views of prisms and pyramids, Drawing of isometric view of cylinders and cones
18-21 Development of Surfaces - Need for preparing development of surface, Concept of
true length - Principal methods of development, Development of simple solids like
cubes, prisms, cylinders, pyramids, cones.
SYLLABUS FOR EMPLOYABILITY SKILLS
SEMESTER-I
(Pl refer to www.dget.nic.in)
12
Syllabus for the trade of Mechanic Motor Vehicle
Second Semester (Semester code No.
)
Duration: Six Months.
Week
No.
Syllabus for Trade practical and Trade Theory
Trade Practical (27 Hrs/week)
Trade Theory (5 Hrs/week)
1&2
Identification of parts in a diesel engine of
LMV/ HMV
3&4
Overhauling of cylinder head assembly,
Use of service manual for clearance and
other parameters, Practice on removing
rocker arm assembly manifolds.
Practice on removing the valves and its
parts from the cylinder head, cleaning.
Inspection of cylinder head and manifold
surfaces for warping, cracks and flatness.
Checking valve seats & valve guide –
Replacing the valve if necessary. Testing
leaks of valve seats for leakage –
Dismantle rocker shaft assembly -clean &
check rocker shaft-and levers, for wear
and cracks and reassemble. Check valve
springs, tappets, push rods, tappet screws
and valve stem cap. Reassembling valve
parts in sequence, refit cylinder head and
manifold & rocker arm assembly,
adjustable valve clearances, starting
engine after adjustments.
Introduction to Engine:
Description of internal & external
combustion engines, Classification of IC
Practice on starting and stopping of diesel
engines, Principle & working of 2&4-stroke
engines.
diesel engine (Compression ignition Engine
Observe and report the reading of (C.I)), Principle of Spark Ignition
Tachometer, Odometer, temp and Fuel Engine(SI), differentiate between 2-stroke
and 4 stroke, C.I engine and S.I Engine,
gauge under ideal and on load condition.
Direct injection and Indirect injection,
Practice on dismantling Diesel engine of Technical terms used in engine, Engine
LMV/HMV as per procedure.
specification.
Study
of
various
gauges/instrument on a dash board of a
vehicleSpeedometer,
Tachometer,
Odometer and Fuel gauge, and Indicators
such as gearshift position, Seat belt warning
light, Parking-brake-engagement warning
light and an Engine-malfunction light.
Different type of starting and stopping
method of Diesel Engine
Procedure for dismantling of diesel engine
from a vehicle..
Diesel Engine Components: Description
and Constructional feature of Cylinder
head, Importance of Cylinder head design,
Type of Diesel combustion chambers,
Effect on size of Intake & exhaust
passages, Head gaskets. Importance of
Turbulence
Valves & Valve Trains- Description and
Function of Engine Valves, different types,
materials, Type of valve operating
mechanism, Importance of Valve seats,
Valve seats inserts in cylinder heads,
importance of Valve rotation, Valve stem
oil seals, size of Intake valves, Valve
trains, Valve- timing diagram, concept of
Variable valve timing. Description of
Camshafts & drives , Description of
Overhead camshaft, importance of Cam
lobes, Timing belts & chains, Timing belts
& tensioners.
13
5
Description & functions of different types
of pistons, piston rings and piston pins and
materials. Used recommended clearances
for the rings and its necessity precautions
while fitting rings, common troubles and
remedy. Compression ratio.
Overhauling piston and connecting rod
Assembly. Use of service manual for
clearance and other parameters:Practice on removing oil sump and oil
pump – clean the sump. Practice on
removing the big end bearing, connecting
rod with the piston. Practice on removing
the piston rings; Dismantle the piston
and connecting rod. Check the side
clearance of piston rings in the piston
groove & lands for wear. Check piston
skirt and crown for damage and
scuffing, clean oil holes.
Measure -the piston ring close gap in the
cylinder, clearance between the piston and
the liner, clearance between crank pin and
the connecting rod big end bearing.
Description & function of connecting
rod, importance of big- end split
obliquely, Materials used for connecting
rods big end & main bearings. Shells
piston pins and locking methods of piston
pins.
Check connecting rod for bend and twist.
Assemble the piston and connecting rod
assembly.
6
7
8
Overhauling of crankshaft, Use of service
manual for clearance and other parameters:Practice on removing damper pulley,
timing gear/timing chain, flywheel, main
bearing caps, bearing shells and crankshaft
from engine checking oil retainer and
thrust surfaces for wear, Measure crank
shaft journal for wear, taper and ovality,
Checking crankshaft for fillet radii, bend
& twist.
Checking of flywheel and mounting
flanges, spigot, bearing. Check vibration
damper for defects, Practice on removing
cam shaft from engine block, Check for
bend & twist of camshaft. Inspection of
cam lobe, camshaft journals and bearings
and measure cam lobe lift. Fixing bearing
inserts in cylinder block & cap check nip
and spread clearance & oil holes & locating
lugs fix crank shaft on block-torque bolts check end play remove shaft - check
seating, repeat similarly for connecting rod
and Check seating and refit.
Cleaning and Checking of cylinder blocks
Surface for any crack, flatness, Measure
cylinder bore for taper & ovality, clean oil
gallery passage and oil pipe line, Bore descale water passages and examine
14
Description and function of Crank shaft,
camshaft, Engine bearings- classification
and location – materials used &
composition of bearing materials- Shell
bearing and their advantages- special
bearings material for diesel engine
application bearing failure & its causes-care
& maintenance. Crank-shaft balancing,
Firing order of the engine.
Description and function of the fly wheel
and vibration damper. Crank case & oil
pump, gears timing mark, Chain sprockets,
chain tensioner etc. Function of clutch &
coupling units attached to flywheel.
Description of Cylinder block, Cylinder
block construction, and Different type of
Cylinder sleeves (liner).
9
10-12
13.
Removing cylinder liners from scrap
cylinder block, practice in measuring and
refitting new liners as per maker’s
recommendations precautions while fitting
new liners.
Reassemble all parts of engine in correct
Sequence and torque all bolts and nuts
as per workshop manual of the engine.
Engine component procedures- Testing
cylinder compression, Checking idle
speed, Removing & replacing a cam
belt, Inspecting & adjusting an engine
drive belt, Replacing an engine drive
belt.
Practice on Checking &Top up coolant,
Draining & refilling coolant, Checking /
replacing a coolant hose, Testing
cooling system pressure, Practice on
Removing & replacing radiator/
thermostat. Inspect the radiator pressure
cap, Testing of thermostat. Cleaning &
reverse flushing. Overhauling water
pump and refitting.
Practice on Checking engine oil, Draining
engine oil, Replacing oil filter, Refilling
engine oil. Overhauling of oil pump, oil
coolers, air cleaners and air filters and
adjust oil pressure relief valves, repairs to
oil flow pipe lines and unions if necessary.
Engine assembly procedure with aid of
special tools and gauges used for engine
assembling. Introduction to Gas Turbine,
Comparison of single and two stage turbine
engine, Different between gas turbine and
Diesel Engine.
Need for Cooling systems, Heat transfer
method, Boiling point & pressure,
Centrifugal
force,
Vehicle
coolant
properties and recommended change of
interval, Different type of cooling systems,
Basic cooling system componentsRadiator, Coolant hoses, Water pump,
Cooling system thermostat, Cooling fans,
Temperature indicators, Radiator pressure
cap, Recovery system, Thermo-switch.
Need for lubrication system, Functions of
oil, Viscosity and its grade as per SAE , Oil
additives, Synthetic oils, The lubrication
system, Splash system, Pressure system,
Corrosion/noise reduction in the lubrication
system. Lubrication system components Description and function of Sump, Oil
collection pan, Oil tank, Pickup tube,
different type of Oil pump & Oil filters Oil
pressure relief valve, Spurt holes &
galleries, Oil indicators, Oil cooler.
Intake & exhaust systems – Description
of Diesel induction & Exhaust systems.
Description & function of air compressor,
exhauster, Super charger, Intercoolers,
turbo charger, variable turbo charger
Dismantling & assembling of turbocharger, mechanism.
check for axial clearance as per service Intake system components- Description
manual.
and function of Air cleaners, Different
type air cleaner, Description of Intake
Check Exhaust system for rubber mounting
for damage, deterioration and out of position; manifolds and material,
for leakage, loose connection, dent and
damage;
Exhaust system components- Description
Practice on Exhaust manifold removal and
Practice on Dismantling air compressor and
exhauster and cleaning all parts - measuring
wear in the cylinder, reassembling all parts
and fitting them in the engine.
15
installation.
Practice on Catalytic converter removal and
installation.
14 16
and function of Exhaust manifold,
Exhaust pipe, Extractors, MufflersReactive,
absorptive,
Combination.,
Catalytic converters, Flexible connections,
Ceramic
coatings,
Back-pressure,
Electronic mufflers.
Practice on removing & Cleaning fuel
tanks, checking leaks in the fuel lines,
soldering & repairing pipe lines and
Unions, brazing nipples to high pressure
line studying the fuel feed system in
diesel engines, draining of water
separators.
Bleeding of air from the fuel lines,
Servicing primary & secondary filters.
Removing a fuel injection pump from
an engine-refit the pump to the engine
re- set timing - fill lubricating-oil start
and adjust slow speed of the engine.
Practice on overhauling of injectors and
testing of injector.
General maintenance of Fuel Injection
Pumps (FIP).
17
18
Practice on Start engine adjust idling
speed and damping device in pneumatic
governor and venture control unit checking
Performance of engine with off load
adjusting timings. Start engine- adjusting
idle speed of the engine fitted with
mechanical governor checking- high
speed operation of the engine.
Checking performance for missing
cylinder by isolating defective injectors
and test- dismantle and replace defective
parts and reassemble and refit back to the
engine
Monitoring emissions procedures by use of
Engine gas analyser or Diesel smoke meter.
Checking & cleaning a Positive crank case
ventilation (PCV) valve. Obtaining &
interpreting scan tool data. Inspection of
EVAP canister purge system by use of scan
Tool.
EGR /SCR Valve Remove and installation
for inspection.
16
Diesel Fuel Systems- Description and
function of Diesel fuel injection, fuel
characteristics, concept of Quiet diesel
technology & Clean diesel technology.
Diesel fuel system components –
Description and function of Diesel tanks &
lines, Diesel fuel filters, water separator,
Lift pump, Plunger pump, Priming pump,
Inline injection pump, Distributor-type
injection pump, Diesel injectors, Glow
plugs, Cummins & Detroit Diesel injection.
Electronic Diesel control- Electronic
Diesel control systems, Common Rail
Diesel
Injection
(CRDI)
system,
Hydraulically
actuated
electronically
controlled unit injector (HEUI) diesel
injection system. Sensors, actuators and
ECU (Electronic Control Unit) used in
Diesel Engines.
Marine & Stationary Engine:- Types,
double acting engines, opposed piston
engines, starting systems, cooling systems,
lubricating systems, supplying fuel oil,
hydraulic coupling, reduction gear drive,
electromagnetic coupling, electrical drive,
generators and motors, supercharging.
Emission Control:- Vehicle emissions
Standards- Euro and Bhart II, III, IV, V Sources
of emission, Combustion, Combustion
chamber design. Types of emissions:
Characteristics and Effect of Hydrocarbons,
Hydrocarbons in exhaust gases, Oxides of
nitrogen, Particulates, Carbon monoxide,
Carbon dioxide, Sulfur content in fuels
Description of Evaporation emission
control, Catalytic conversion, Closed loop,
19
Practice on removing alternator from
vehicle dismantling, cleaning checking for
defects, assembling and testing for
motoring action of alternator & fitting to
vehicles.
Practice on removing starter motor Vehicle
and overhauling the starter motor, testing of
starter motor
20 &
21
Crankcase emission control, Exhaust gas
recirculation (EGR) valve, , Controlling airfuel ratios, Charcoal storage devices, Diesel
particulate filter (DPF). Selective Catalytic
Reduction (SCR), EGR VS SCR
Description .of charging circuit operation
of alternators, regulator unit,
ignition
warning lamp- troubles and remedy in
charging system.
Description of starter motor circuit,
Constructional details of starter motor
solenoid switches, common troubles and
remedy in starter circuit.
Troubleshooting : Causes and remedy for
Engine Not starting – Mechanical &
Electrical causes, High fuel consumption,
Engine
overheating,
Low
Power
Generation, Excessive oil consumption,
Low/High Engine Oil Pressure, Engine
Noise.
Practice
on
troubleshooting
in
LMV/HMV for Engine Not starting –
Mechanical & Electrical causes, High
fuel consumption, Engine overheating,
Low Power Generation, Excessive oil
consumption, Low/High Engine Oil
Pressure, Engine Noise.
22-23
In-plant Training
24-25
Revision and Test
26
NCVT Exam
17
Automobile Group – 2 years Trade
2nd Semester
Workshop Calculation and Science
Syllabus for the trade of
1. Mechanic Motor Vehicle
Week
No.
1&2
3
4-6
7 -10
Workshop calculation and
Science (3 Hrs/week)
2nd Semester
Factorisation and quadratics: multiply expressions in brackets by a number, symbol
or by another expression in a bracket; by extraction of a common factor eg ax + ay, a(x
+ 2) + b(x + 2) ; by grouping eg ax − ay + bx − by ; quadratic expressions eg a2 + 2ab +
b2 ; roots of an equation eg quadratic equations with real roots by factorisation, and by
the use of formula
Geometry– Use of scientific calculator,/logarithmic table
Angles -Angular
measurement, Angles and rotation, Examples of angles in automotive work, Adding and
subtracting angles. Types of angle- Adjacent angles, Opposite angles, Corresponding
angles, Alternate angle
Angles.
Supplementary
angles,
Complementary
TrigonometryTypes of
triangle
- Acute angledangles,
triangle, Obtuse angled triangle,
Equilateral triangle, Isosceles triangle, Scalene triangle, Right angled triangle,
Labelling sides and angles of a triangle, Sum of the three angles of a triangle.
Pythagoras’ theorem, Circles, Ratio of diameter and circumference, Length of arc,
Timing marks, Wheel revolutions and distance travelled, Valve opening area.
Trigonometry- Using sines, cosines and tangents to solve vehicle problems.
Formulae for Perimeter and Area of Plane figure - Rectangle, Square, Parallelogram,
Triangle, Hexagon, any regular polygon, Trapezium, Circle, sector, Fillet, Ellipse,
segment of a circle;
Formulae for Volume and surface area of solids- Rectangular solid, Prism, cylinder,
pyramids and cones, Frustum of pyramid and cones, sphere, Hollow sphere, segment of
sphere, circular ring, spherical sector,
Calculation of volume and weight of simple solid bodies such as cubes, square and
hexagonal prism-shop problem.
Statistics – Collecting and sorting raw data, Definition of Discrete variable, continuous
variable with Shop examples. Constructing pictographs-pie chart, Bar chart. Frequency
and tally Charts. Importance of the shape of a frequency distribution- histogram,
frequency polygon, Cumulative frequency plot. Interpreting statistics- sampling,
arithmetic mean, median, mode, Range. Graphs- variables, scales, coordinates, straight
line graphs.
14 & 15 Heat and temperature –Temperature-Thermodynamic temperature scale (Kelvin),
Cooling system temperature; Standard temperature and pressure (STP); Thermal
expansion with calculation; Heat- Sensible heat, Latent heat, Specific latent heat, Specific
heat capacity, Quantity of heat with calculation; Heat transfer – Conduction, Convection,
16 & 17 Radiation
Heating, ;expansion and compression of gases - Absolute pressure, Absolute
temperature; Laws relating to the compression and expansion of gases -Heating a gas at
constant volume, Heating a gas at constant pressure, Charles’ law. Expansion or
compression at constant temperature – isothermal
11-13
18
18-20
Internal combustion engines- Engine power-Brake power, Horsepower, PS – the DIN,
Indicated power, Mean effective pressure, Calculation of indicated power, Cylinder
pressure vs. crank angle, Mechanical efficiency of an engine, Volumetric efficiency,
Torque vs. engine speed, Specific fuel consumption vs. engine speed, Brake power,
torque and sfc( Specific fuel consumption) compared, Brake mean effective pressure,
Thermal efficiency, Indicated thermal efficiency, Brake thermal efficiency petrol vs.
Diesel.
21
Fuels and combustion- Calorific value, Combustion-Products of combustion, Relevant
combustion equations. Air–fuel ratio-Petrol engine combustion, Detonation, Preignition, Octane rating, Diesel fuel, Flash point , Pour point, Cloud point, Biofuels,
Liquefied petroleum gas (LPG) ,Hydrogen, Zero emissions vehicles (ZEVs)
19
Automobile Group – 2 years Trade
2nd Semester
Engineering Drawing
Syllabus for the trade of Mechanic Motor Vehicle
Week
Engineering Drawing (3 Hrs/week)
Nos.
2nd Semester
1-4
Read and interpret drawings- Determine information from the title block, Read and
interpret industrial prints, Read and interpret detailed and assembly drawings,
Identify casting drawings and machining drawings, Read and interpret diagrams,
Distinguish between a monodetail and a multidetail drawing.
5-8
Identify different drawing projections - Interpret pictorial and multi-view drawings.
Interpret auxiliary and section views, Determine views in a drawing and the
significance of the view being shown. Identify missing lines and missing views.
9-12 Free hand sketching of key and screw threads. Read and interpret three Types of
screw thread representation: pictorial, schematic and simplified presentation. Terms
used in describing a threaded Part, Designation of Thread Specifications, Left-Hand
Thread Notations, read and interpret the different type of Finish Symbols, Fillets and
Rounds and Machine Slots.
13
Drawing of I .C engine – Diesel and their parts.
14
Sketching of otto cycle, Diesel cycle, valves and valve timing diagram.
15
Free hand sketch of piston assembly, Free hand sketching of piston gudgeon pins
rings and connecting rod .
16
Free hand sketching of crank shaft and cam shaft showing all parts.
17
Free hand sketching of cylinder block and cylinder head, cylinder liners.
Free hand sketching of different cooling system -showing all necessary parts such as
18
water pump, thermostatic valve, Radiator etc.
Free hand sketching of lubrication system, showing all necessary parts such as filters ,
19
oil pump, pressure release valve etc.
20
Freehand sketching of staring system.
21
Freehand sketching of charging system and solenoid switch circuit.
SYLLABUS FOR EMPLOYABILITY SKILLS
SEMESTER-II
(Pl ref to www.dget.nic.in)
20
Syllabus for the trade of Mechanic Motor Vehicle
Third Semester (Semester code No.
)
Duration: Six Months.
Syllabus for Trade practical and Trade Theory
Trade Practical (27 Hrs/week)
Trade Theory (5 Hrs/week)
Week
No.
Identification of different major components Introduction: Study of different major
1
of Heavy vehicle and their function & components & assemblies of heavy vehicle,
placement study of different make and different make (indigenous). Name
lorry/bus/tractor in Institute with different plate-constructional differences and their
dealers or organizations.
merits. leading manufacturers in Heavy
vehicle Industry
2 -4
Practice on adjusting clutch pedal play- Clutches & Manual Transmissions-Clutch
removing gearbox and clutch assembly from principles, Single-plate clutches, Multi-plate
Light & Heavy Vehicle. Dismantling clutch clutches, Dual mass flywheels, Operating
assembly, cleaning inspecting parts.
mechanisms
Removing & fitting of new pilot bearing, Clutch components- Pressure plate, Driven/
removing & fitting of ring gear in fly wheel center plate, Throw-out bearing.
relining a clutch plate, checking condition of Manual transmissions- Gear ratios,
flywheel and pressure plate surface for Compound gear trains, Gear selection,
reconditioning.
Bearings, Oil seals & gaskets, Brief about
Assembling of pressure plate adjusting the Automated Manual Transmission (AMT)
fingers checking run out of fly wheel and Gearbox layout & operationaligning clutch assembly with flywheel.
Gearbox layouts, Transaxle designs,
Dismantling cleaning and assembling of Gearbox operation, Baulk-ring synchromesh
gearshift mechanism changing oil in gear unit, Transaxle synchromesh unit. Gear shift
box.
mechanism.
Dismantling a synchromesh gear box,
cleaning, inspecting parts replacing worn out
defective parts assembling & testing for
correct performance identifying noises from
gear boxes and rectifying.
5-7
Practice on Removing open type propeller Final Drive & Drive Shafts - Basic layouts
shaft from vehicle, Practice on removing Front-wheel drive layout, Rear-wheel drive
universal joints, cleaning replacing worn out layout, Four-wheel drive layout, All-wheel
parts, re-assembling & refitting to vehicle- drive layout, 4WD v/s AWD
and their alignment special precautions Front-wheel drive, Front-wheel drive shafts,
while removing torque tube drive shaft.
Front-wheel final drives, Front-wheel
Practice on FWD Driveshaft Removal
differentials
and Replacement.
Rear-wheel drive- Propeller shaft, Type of
Practice on overhauling & inspection of rear Universal joints, Type of Constant velocity
axle.
Joints, Rear-wheel final drives, Salisbury
Practice on overhauling & inspection of axles, Rear-wheel drive differentials,
differential assembly.
Limited slip differentials.
Trouble shooting – causes and remedy for Four-wheel drive- Four-wheel drive shafts,
clutch slip, clutch noise, clutch binding, hard Four-wheel final drive, Four-wheel drive
clutch, gearbox noise, gear slip, rear axle transfer case, Freewheeling hubs, Fournoise, propeller shaft noise, universal joint wheel drive differentials
noise, differential noise.
All-wheel drive- four wheel final drives,
21
8&9
Identification of Automatic transmission
components
Checking automatic transmission fluid,
Changing transmission fluid & filter.
Checking automatic transmission fluid,
Changing transmission fluid & filter.
Practice on oil pressure control cable play
adjustments, Inspection of shift lever switch,
throttle position sensor, speed sensor and
automatic transmission wiring harness
coupler.
22
All-wheel drive transfer case, Transfer case
differential action.
Automatic Transmissions - Torque
converters, Torque converter principles,
drive plate, Converter operation, Torque
multiplication, Fluid flow, Heat exchanger,
Lock-up converters, clutches.
Planetary gearing- Planetary gears, Simple
planetary gear sets, Compound planetary
gear sets, Automatic transmission brake
bands,
Multi-disc
clutches,
Electronic
control
transmission
Electronic control Unit, Fully hydraulically
controlled transmission, Electronic shift
programs, Manual selection.
Layout & operation for P,R,N&D (1st & 2nd)
Selector positions, Planetary gear set, High
range power flow, Low range power flow
Servos & clutches-Rear servo, Front servo,
One way clutch, Multi-plate front clutch,
Clutch pack, Rear clutch.
Hydraulic system & controls-Hydraulic
system
components,
Spool
valves,
Regulating or flow control valves, Control
valves, Orifices
Valve types & functions- Basic valve
action, Regulator & control valves, Shift &
governor valves
Pressure
regulationThe
primary
regulating valve, Line pressure variation,
Modulator valve pressure, The governor,
Governor pressure, Kickdown pressure.
Flow control- Gear position 1, 1-2 shift
valve, 2-3 shift valve assembly, The servo
orifice control valve, 3-2 kick down
Continuously
variable
transmission
(C.V.T.)Continuously
variable
transmission, Drive or reverse, The steel
belt, Secondary pulley shaft.
10-12 Following practical to be Practiced On Light
& Heavy Vehicle.
Practice on removing the drop arm, Check
and adjust the turning angle, align the drop
arm and steering wheel with the front wheel.
Check and correct toe-in.
Practice on removing steering wheel,
steering gearbox.
Inspect and overhaul steering boxes,
adjusting steering gear backlash, pre-load
and adjust toe-in, toe-out, camber angle,
castor angle, kingpin inclination and wheel
run out. Checking & adjusting power
steering fluid, Pressure testing a power
steering system, Flushing a power steering
system, Inspecting & adjusting an engine
drive belt, Servicing a steering system,
Servicing wheel bearings.
Troubleshooting- Causes and remedy for
abnormal wear of tyre, wheel wobbling,
poor self centering, hard steering, and
vehicle pulling to one side.
Steering Systems:- Description and
function of Steering systems, Principles of
steering, Rack-and-pinion steering system,
Recirculation ball & nut steering system,
Four-wheel steering systems, collapsible
steering system.
Steering boxes & columns - Description
and function of Steering columns, Rack-andpinion gearbox, Helix, Variable ratio
steering, Worm gearbox, Power Assisted
steering, Steering process, Flow-control
valve, Electric power assisted steering,
Basic electric power steering operation
Steering arms & components- Forward
control vehicle steering, Steering linkages,
Joints, Bushes/bushings
Wheel
alignment
fundamentals:Basic principles of wheel alignment,
wheel base, wheel track, king pin
inclination, Caster, Camber, Scrub radius,
Toe-in & toe out, Toe-out on turns,
Turning radius, Thrust angle &
centerlines.
13-15 Following practical to be Practiced On Light Suspension Systems:& Heavy Vehicle
Principles of suspension, Suspension force,
Unsprung weight, Wheel unit location,
Practice on visual Inspection of chassis Dampening. Types of suspensionframe for crack, bent and twists.
Suspension systems, Solid axle, Dead axle,
Overhauling and
Inspection of shackle, Description, function and advantages of non
independent suspension Independent
leaf spring, front & rear suspension.
suspension, Rear independent suspension,
Practice on removing, inspection and Rear-wheel drive independent suspension,
assembling of shock absorber
electronically controlled air suspension
Lubricating a suspension system.
(ECAS), Adaptive air suspension operation.
Trouble shooting for Suspension system Types of springs - Description and function
defects :
of Coil springs, Leaf springs, Torsion bars,
wheel hop, ride height (unequal and low), Rubber springs.
noises under operation, fluid leakage, Shock absorber types- Description and
excessive travel, bounce, worn dampers, function of Hydraulic shock absorbers, Gasworn joints/damaged linkages, vehicle pressurized shock absorbers, Load“crabbing”.
adjustable shock absorbers, Manual
adjustable-rate shock absorbers, Electronic
adjustable-rate shock absorbers, Automatic
load-adjustable shock absorbers
Front suspension types & componentsMc person Strut suspension, Short/long arm
suspension, Torsion bar suspension
Rear suspension types & components-Rigid
axle leaf spring suspension, Rigid axle coil
23
16
Practice on removing wheels from light &
Heavy vehicle, dismantling tyres and tubes
checking puncture.
Assembling inflating to correct pressure.
Checking & adjusting tire pressure by use of
air or by Nitorgen
Rotating the wheels in vehicle minor repairs
to wheels and tyres, wheel balancing &
alignment.
Checking for tyre wear patterns.
Caution: vehicle equipped with ABS while
removing the wheel and using on vehicle
balancing never ignition switch on (Follow
the service manual procedure)
17-19 Practice on Adjusting brake pedal play,
Overhauling and inspection of tandem
master cylinder assembly,
Overhauling and inspection of front and rear
brake assembly, overhauling and inspection
of wheel cylinder assembly.
Bleeding hydraulic brakes & Disk brakes.
Overhauling and inspection of vacuum
assisted brake assembly.
Overhauling and inspection of disc brake.
Adjusting Air brakes- repair to tank unit, air
compressor, wheel brake adjuster- locating
air leaks in the brake lines and rectifying –
general maintenance and care.
Brakes procedures-Checking & adjusting
brake fluid, Replacing brake fluid, Checking
brake pads, Replacing brake pads,
Removing & replacing a rotor, Replacing
brake linings, Adjusting a parking brake
cable.
Trouble tracing in braking system of a heavy
vehicle adjusting brakes and balancing all
four wheel brakes, precautions to be
observed while testing brakes points to be
remember while preparing the vehicle for
brake certificate.
Practice of maintaining of ABS system.
24
spring suspension, Independent type
suspension, Rigid non-drive suspension
Wheels & Tyres-Wheel types & sizes
Wheels, Rim sizes & designations, Types of
wheels
Tyre types & characteristics- Tyres,
Radial ply tyres, Radial ply tyre sidewalls,
Tyre pressure monitoring systems, Run flat
tyres, Space-saver tyres, Tyre distortion,
Center of gravity.
Tyre construction-Tyre construction, Types
of tyre construction, Tyre materials,
Hysteresis, Tyre sizes & designations, Tyre
information, Tyre tread designs, Tyre ratings
for temperature & traction. Descriptions
Tirewear Patterns and causes
Nitrogen vs atmospheric air in tyres
Braking Systems :- Principles of braking,
Drum & disc brakes, Lever/mechanical
advantage, Hydraulic pressure & force,
Brake pad, Regenerative braking.
Braking systems - Brake type - principles,
Air brakes, Exhaust brakes, Electric brakes,
Parking brakes, Engine brakes, Regenerative
braking
Braking system components-Park brake
system, Brake pedal, Brake lines, Brake
fluid, Bleeding, Master cylinder, Divided
systems, Tandem master cylinder, Power
booster or brake unit, Hydraulic brake
booster, Electro hydraulic braking (EHB),
Applying brakes, Brake force, Brake light
switch
Drum brakes & components -Drum brake
system, Drum brake operation, Brake linings
& shoes, Back plate, Wheel cylinders
Disc brakes & components -Disc brake
system, Disc brake operation, Disc brake
rotors, Disc brake pads, Disc brake calipprs,
Proportioning valves, Proportioning valve
operation, Brake friction materials
Antilock braking system & componentsABS brake system, Antilock braking system
operation, Principles of ABS braking, ABS
master cylinder, Hydraulic control unit,
Wheel speed sensors, ABS with EBD
electronic control unit.
The construction and operation of heavy
vehicle Anti-Slip Regulation / Traction
Control (ASR) system.
20 &
21.
Trouble shooting Practice with Heavy Study of Motor Vehicle act Rules &
vehicle for
Regulation-Laws governing to use of motor
Engine Not starting – Mechanical &
vehicle & vehicle transport, Licensing of
Electrical causes,
drivers & conductors, Registration of
High fuel consumption,
vehicle, Traffic rules, Signals & controls,
Engine overheating,
Accidents, Causes & analysis,
Low Power Generation,
Responsibility of driver, Offences, penalties
Excessive oil consumption,
& procedures, Different types of forms,
Low/High Engine Oil Pressure,
Government administration structure,
Engine Noise.
Personnel, Authorities & duties, Rules
regarding construction of motor vehicles,
Tax exemption & tax renewal, Insurance
types & significance -Comprehensive
Third party insurance, Duty of driver in case
of accident
22-23
24-25
26
In plant training
Revision and Test
NCVT Exam
25
Automobile Group – 2 years Trade
3rd Semester
Workshop Calculation and Science
Syllabus for the trade of
1. Mechanic Motor Vehicle
Week
No.
Workshop calculation and
Science (3 Hrs/week)
3rd Semester
1& 2
Data interpretation
3&4
5 &6
Allegations or Mixture
Levers and moments, torque and gears - definition of Levers, Principles of leverageThe principle of moments. The bell crank lever, A practical application of the bell crank
lever in vehicle. Axle loadings, A steering mechanism as a machine
7-9
Friction – Definition of friction, Coefficient of friction, Static friction, Sliding friction;
Making use of friction – Clutch- Torque & power transmitted by a plate clutch and
Example calculation, Belt drive- Torque & power transmitted by a belt drive and
Example calculation, speed ratio of belt drive.
Velocity and acceleration, speed - Definition of Speed and velocity, Acceleration,
Velocity–time graph- Uniform velocity, Uniform acceleration, Equations of motion and
their application to vehicle technology. Problems on speed and velocity.
10-12
13-15
16-18
19-21
Force, mass and acceleration-Newton’s laws of motion, Relation between mass and
weight. Inertia, Motion under gravity, Angular (circular) motion, Equations of angular
motion Relation between angular and linear velocity, Centripetal acceleration,
Accelerating torque
Vehicle dynamics -Load transfer under acceleration, Static reactions, Vehicle under
acceleration, , Definition of tractive effort, Tractive resistance-Rolling resistance, air
resistance, gradiant resistance, Inertia. Power required to propel vehicle, Forces on a
vehicle on a gradient – gradient resistance, Gradeability, Vehicle power on a gradient,
Vehicle on a curved track, Overturning speed, Skidding speed
Balancing and vibrations – Balance of rotating masses acting in the same plane
(coplanar). Engine balance, Simple harmonic motion (SHM), Applications of SHMVibration of a helical coil spring, Torsional vibration, Free vibrations, Example of free
vibrations, Forced vibrations- Resonance, Driveline vibrations, Damping, Vibration
dampers, Dual mass flywheel, Cams.
26
Automobile Group – 2 years Trade
3rd Semester Engineering Drawing
Syllabus for the trade of Mechanic Motor Vehicle
Week
Nos.
1&2
3&4
5&6
7&8
9&10
11&12
13&14
15&16
17&18
19&21
Engineering Drawing (3 Hrs/week)
3rd Semester
Lay out of synchromesh gear box unit, and showing the different gear engaged
positions.
Free hand sketching of Front-wheel drive layout, Rear- wheel drive layout, Fourwheel drive layout, All-wheel drive layout, joints & Universal Joint.
Free hand sketch of Torque converter Selector positions, Planetary gear set, High
range power flow, Low range power flow
Free hand sketching of propeller shaft, Universal Joint and Rear wheel final drive
Free hand sketching of different types of steering boxes. Layout of power steering
system
Free hand sketching of caster, camber, king-pin angle. Ackerman’s angle toe-in &
toe-out.
Free hand sketching of Independent rear suspensions, Front suspension,
Bushes/bushings, Arms & linkages and Rigid axle suspension (Leaf spring)
Free hand sketching of different type of shock absorrbes.
Free hand sketching of different type of wheels.
Free hand sketching of different type of tyre treads design.
Drawing constructional details of radial and conventional tyres.
Free hand sketching of wheel brake assembly sectioned views of master cylinder.
Free hand sketching of wheel cylinders, brake shoe assembly and anchor pins.
Freehand sketching – The layout of vacuum assisted hydraulic brake system
Freehand sketching of the layout of Air brake system and sketching of slacke
adjuster.
Freehand sketching of the layout of Parking Brake, Air brake system and sketching
of slacke adjuster.
Circuit layout of ABS
27
Syllabus for the trade of Mechanic Motor Vehicle
Fourth Semester (Semester code No.
)
Duration: Six Months.
Syllabus for Trade practical and Trade Theory
Week
Trade Practical (27 Hrs/week)
Trade Theory (5 Hrs/week)
No.
1 & Identification of petrol Engine components. Petrol Engine Basics:
2
Practice on starting and stopping of petrol
4-stroke spark-ignition engines- Basic 4engines. Observe and report the reading of stroke principles.
Tachometer, Odometer, temp and Fuel
Spark-ignition engine components- Basic
gauge under ideal and on load condition.
engine components, Engine cams & camshaft,
Removing a petrol engine from a motor Engine power transfer, Scavenging, Counter
vehicle. Dismantling cylinder head for weights, Piston components.
Inspection.
Intake & exhaust systems -Carbureted
Practice on Removing of piston and systems, Electronic fuel injection systems,
connecting rods from engine checking
Exhaust systems.
Cylinder bore wear for ovality and taper. Intake system components, Air cleaners,
Piston ring, Piston as per service manual.
Carburetor air cleaners, EFI air cleaners, Intake
Checking valves - replacing worn guides manifolds, Intake air heating.
and weak springs, assembling valves and Gasoline Fuel Systems : Description of
cylinder head and adjusting tappet clearance Gasoline fuel, Gasoline fuel characteristics,
in engine.
Controlling fuel burn, Stoichiometric ratio, Air
density, Fuel supply system, Pressure &
vacuum.
3
Simple repairs in fuel feed system –
overhauling of fuel pump, carburetors, fuel
Filters and air cleaners. Repair to a car
carburetors – adjusting
float level and slow speed adjustments –
studying the fuel flow circuit in carburetor
Practice in engine tune up in a vehicle –
testing vacuum and compression of engine,
Carburetor operation-Carburation, Carburetor
systems, Metering jets, Accelerating, Carburetor
barrels
Carbureted
system
components
The carburetor, Mechanical fuel pumps, Electric
fuel pumps, Tanks & lines, Fuel lines, Charcoal
canister, Carburetor filters.
4&5
Practice on Cleaning fuel tank, checking for
leaks in Fuel tank. Identification of various
components of MPFI system.
Testing of MPFI components and
replacement if necessary. Check delivery
from fuel Pump. Replacing a fuel filter.
6&7
Identification of Electronic control Unit.
Set up for testing, Testing of Electronic
Introduction to Electronic fuel injection
(EFI) fuel supply system , Basic EFI
principles, Air supply, Air volume, Multi-point
injection systems (MPI/MPFI), Simultaneous
injection, Efficient combustion
EFI fuel supply system components - Fuel
pumps, Fuel filters, Tanks & lines, Fuel lines,
Fuel rail, Fuel pressure regulator, Injectors,
Tachometric relay, Thermotime switch, EFI
sensors, Potentiometer, Auxiliary air valves,
Idle speed control devices, Inertia sensors.
Introduction to EFI Engine Management EFI operation Modes of EFI, Electronic fuel
28
Control Circuit. Fault finding in Electronic
circuit and remedies using scan tool.
Identification of various sensors installed in
engine & it’s mounting.
Checking
instruments & Gauges on dash board.
Rectify replace defective gauges.
Testing of Temperature sensor, Pressure
senor, potentiometer, magnetic induction
sensor, cam shaft sensor, crankshaft position
sensor.
injection, Idle speed control systems, Feedback
& looping, Cold start systems, Air
measurement, Air-flow monitoring, Variable
intake manifold system, Electrical functions,
EFI wiring diagram
Electronic control unit (ECU) - EFI system
ECU, Electronic control unit settings, Engine
speed limiting, Malfunction indicator lamp.
Importance of Diagnostic Trouble Code (DTC)
& its general format. Use of scan tool and
retrievals of codes.
EFI sensors- Intake Temperature sensor, Mass
airflow sensor, Manifold absolute pressure
sensor, Air vortex sensor, Fuel system sensor,
Throttle position sensor, Exhaust gas oxygen
sensor, Crank angle sensor, Hall effect voltage
sensor,
Ignition principles and Faraday’s laws,
Primary and secondary winding of transformer,
Ignition components, Spark plugs, Spark plug
components, Vacuum & centrifugal units, Plug
firing voltage,
Induction, Inductive system operation,
Induction wiring, Hall effect sensors, Hall effect
operation, Optical type sensors
Distributor less ignition systems, Insulated coils,
Distributor less ignition system timing.
Charging system- The purpose of Charging
system, charging system components, charging
system circuit,
Alternator principles,
Alternating current, Alternator components,
Rectification, Phase winding connections, Rotor
circuit, Voltage regulation, System operating
voltage, High voltage charging systems, Rotor,
Stator, Alternator end frames, Slip ring & brush
assembly, Rectifier assembly, Alternator
cooling fan.
8
Diagnosis- Possible causes and remedy for
Engine cranks, but will not or hard to start,
Poor fuel economy or engine performance.
Checking ignition timing, Checking &
changing a spark plug, Identification and
testing of Hall effect sensor, Optical sensor.
Tracing and testing of sensor circuits.
9&
10
Checking a charging system for the cause of
undercharge, No charge, and over charge
conditions.
Removing & replacing an
alternator, Inspection of rotor for ground,
open circuit – field coil resistance, slip ring
surface, Fan, bearing. Inspection of stator
for ground, open circuit, Inspection of Drive
end bearing rotation, Rectifier, brush length
compare with service manual. slip ring
surface. Inspecting & adjusting an engine
drive belt, Replacing an engine drive belt /
pulleys / Tesnionsers and their alignments.
Trouble shooting, possible causes and
remedy for warning lamp does not glow
when ignition switch is on, Warning lamp
glows dim when ignition switch is on,
warning lamp ‘on’ while the alternator is
running, Warning lamp glows ‘dim’ while
the alternator is running, warning lamp
flickers considerably.
Removing starter motor from vehicle, and
Starting system- purpose of starting system,
Performance test for pull-in test, Hold-in
Staring system components, Starter motor
test, pinion (plunger) return test, No-load
principles, study of starter control circuits.
11 &
12
29
performance test.
Starter motor construction, Starter magnet
Solenoid test for Hold in coil open circuit,
types, Starter motor engagement, Commutation,
Armature test – Ground test, Open circuit
Switching, solenoid construction.
test, pull-in coil open circuit test, field coil
test. Inspections of brush length wear as per
service manual.
Trouble shooting , possible causes and
remedy for starter motor not running,
Starting motor running but too slow (small
torque), staring motor running, but not
cranking engine. Noise, starting motor does
not stop running. Growler testing for rotors.
Checking a starting system, Jump-starting a
vehicle
13 &
14
Trace the light circuit - test bulbs, align head
lamps, Aiming headlights. Changing a
headlight bulb, Checking of a head light
switch and to replace if faulty.
Trouble shooting and remedy for Headlight
- headlight do not light up, only one
headlight does not light up, Only one beam
(“Hi” or “Lo”) does not light..
Trouble shooting and remedy for turn signal
and hazard warning lights -Flash rate high or
one side only flashes, No Flashing, flash rate
low.
Trouble shooting and remedy for clearance,
tail and license plate lights - All lights do
not light up, some lights do not light up.
Trouble shooting and remedy for Back-up
light - Back-up lights do not light up.
Trouble shooting and remedy for Brake
lights -Brake lights do not light up, Brake
light stay on.
Trouble shooting and remedy for fuel meter
and fuel gauge unit - Fuel meter shows no
operation or incorrect operation.
Trouble shooting and remedy for Engine
coolant Temp (ECT) meter and ECT Sensor
– Engine coolant temp meter shows no
operation or incorrect operation.
Trouble shooting and remedy for oil
pressure light – Oil pressure warning light
does not light up when ignition switch is on
at engine off.
Trouble shooting and remedy for brake and
parking brake warning light- Brake warning
light does not light up when fluid flow level,
Brake warning light does not light up when
Lighting
system,
Lamps/light
bulbs,
Lamp/light bulb information, LED lighting,
Headlights-description of standard sealed beam,
halogen sealed beam, composite and High
intensity discharge (HID) headlights. Headlight
& dimmer circuits, Park & tail light circuits,
Brake light circuits, turn signal circuit,
Cornering lights, Fog lights circuit, interior
lights- courtesy, reading and instrument panel
lights, Smart lighting , Reverse lights
30
15 &
16
17 &
18
parking brake pull up, Brake warning lights
stay on.
Trouble shooting and remedy for interior
light- Interior light do not light up.
Trace the wiring circuit of traffic signal
flashers light circuit-tracing
defects in the flasher circuits, replacing fuse
bulb.
Identification of
Air conditioning
components, Performance test on A/c unit,
Checking Charged state of refrigerant,
Inspecting & adjusting an engine drive belt,
Replacing an engine drive belt.
Checking a heating system, Compressor
rotation test, air Gap check,
Refrigerant recovery –evacuating –charging
of A/c system. Replenishing compressor oil
level. Troubles diagnose and remedy for No
cooling or warm air, Cool air comes out
only intermittently, Insufficient cooling,
Abnormal noise from compressor, Magnetic
clutch, condenser, evaporator, Blower
motor. Diagnosis test for High pressure
gauge –pressure high and low, Low pressure
gauge for pressure high and low.
Trouble shooting and remedy for Horn- No
horn operation, poor sound quality, horn
sounds continuously and to replace the horn
if faulty.
Remove and install wiper motors and wiper
switches. Checking & replacing wiper
blades.
Trouble shooting and remedy for windshield
wiper and washer - no operation,
intermittent operation, continuous operation,
and wipers will not park.
Diagnose causes for improper operation of
the windshield washer system and to replace
the pump if faulty.
Diagnose the power window system for – all
power window motors do not operate, some
switches do not operate.
Diagnose the power door lock control for –
All power door locks do not operate, only
one power door lock not operate.
Diagnose for remote keyless entry and
immobilizer system.
Familiarization of car radio wiring and
Heating Ventilation Air Conditioning
(HVAC)
legislation,
Vehicle
heating,
ventilation & cooling systems, Basic airconditioning
principles,
Air-conditioning
capacity, Air-conditioning refrigerant, Humidity
Description and function of Fixed orifice,
Control devices, Thermostatic expansion valve
system, Thermal expansion valves, Airconditioning compressors, Condensers &
evaporators, Receiver drier, Lines & hoses, TX
valve construction, Temperature monitoring
thermostat, Refrigerants, Pressure switches,
Heating elements
Air-conditioning ECU, Ambient air temperature
sensor, Servo motors, Electric servo motors,
Automatic climate control sensors, Evaporator
temperature sensor, Blower speed control,
Ventilation systems.
Accessories: Horn circuit, wiper circuit, power
window components and circuit. Power door
lock circuit, automatic door lock circuit, remote
keyless entry system circuit, antitheft system,
immobilizer system. Navigation system, Car
radio and cassette player, car videos.
Description and function of Airbags, Seatbelt,
Vehicle safety systems, Crash sensors, Seat belt
pre-tensioners, Tire pressure monitoring
systems
Integrated communications, Proximity sensors,
Reflective displays, Global positioning
satellites, Triangulation/trilateration,
Telematics. Networking & multiplexing
.
31
speaker circuits
Diagnose automatic seat belt systems,
Diagnose air bag system and service
warnings.
19-21 Driving Practice.
Locating vehicle information, Obtaining &
Practice in straight driving on wide roads.
interpreting scan tool data, Using a repair
Driving through lanes and curves.
manual, Using a shop manual, Using an owner's
Practice in reversing. Practice overtaking
manual, Using a labor guide, Using a parts
another vehicle. Practice in driving through program, Using a service information program
sand and wet surfaces. Practice in parking
and Diagonal parking.
22-23
Project work
24-25
Revision and Test
26
NCVT Exam
32
Automobile Group – 2 years Trade
4th Semester
Workshop Calculation and Science
Syllabus for the trade of
1. Mechanic Motor Vehicle
Week
No.
1&2
3&4
5-7
8 &9
Workshop calculation and
Science (3 Hrs/week)
4th Semester
The binary system- Most significant bit (MSB), Hexadecimal, Converting base 10
numbers to binary 10, Uses of binary numbers in vehicle
Electrical principles- Electric current, Atoms and electrons, Conductors and insulators, Conductors, Semiconductors, Insulators, Electromotive force, Electrical power sources –
producing electricity- Chemical power source, Magnetic power source, Thermal power
source, Effects of electric current – using electricity,
Electrical circuits- Circuit principles, A simple circuit, Direction of current flow,
Electrical units- Volt, Ampere, Ohm, Watt; Ohm’s law, Resistors in series, Resistors in
parallel, Alternative method of finding total current in a circuit, containing resistors in
parallel, Measuring current and voltage, Ohmmeter, Open circuit, Short circuit.
Temperature coefficient of resistance- Negative temperature coefficient; Electricity and
magnetism- Permanent magnets, The magnetic effect of an electric current, Direction of
the magnetic field due to an electric current in a straight conductor, Magnetic field caused
by a coil of wire;
Solenoid and relay, Electromagnetic induction, The electric motor effect, Fleming’s rule,
Alternating current- Cycle, Period, Frequency; Applications of alternating current,
Transformer,
Lenz’s law, Capacitance,
Inductance, Back
emf, Inductive
reactance, Time
constant
an inductive
12 & 13 CapacitorsCapacitors
in circuits-Contact
breaker
ignitionfor
circuit,
circuit,
Capacitive
discharge ignition system, Capacitors in parallel and series, Impedance.
10 & 11
14 &15
Electronic principles-Introduction, Semiconductors- Effect of dopants, Electrons and
holes, The p–n junction, Bias, Behaviour of a p–n junction diode, Diode protection
resistor, Negative temperature coefficient of resistance – semiconductor, The Zener diode.
16 &17
Light emitting diode (LED) - Voltage and current in an LED, Photodiode, Bipolar
transistors-Basic operation of transistor, Current gain in transistor, Current flow in
transistors; Transistor circuit used in automotive applications- Voltage amplifier,
Darlington pair, Heat sink;
18 & 19
Filter circuits, Voltage divider, Integrated circuits, Sensors and actuators, Control unit
(computer) inputs and outputs, Logic gates-The RTL NOR gate, Truth tables, Bits, bytes
and baud.
20 & 21
Properties of refrigerants, refrigerant oil, Fluorinated refrigerants, Refrigeration process –
pressure/enthalpy diagram
33
Automobile Group – 2 years Trade
4th Semester Engineering Drawing
Syllabus for the trade of Mechanic Motor Vehicle
Week
Nos.
1&2
Engineering Drawing (3 Hrs/week)
4th Semester
Introduction to AutoCAD, Starting AutoCAD, Exercises Using Draw commands asLine, Polygon, Rectangle, Circle, Ellipse.
3-5
Exercises on using Edit Commands as Erase, Copy Mirror, Offset, Extend, Array,
Move, Rotate, Scale, Trim
Chamfer, Fillet
6&7
Exercises on using X,Y,Z, coordinate entry system for Angular measurement,
Absolute Coordinate, Relative coordinate, Polar coordinate.
8
Exercises on using Drawing Aids -grid and snap, ortho and polar tracking,
PolarSnap, running object snaps, the From snap, and object snap tracking.
9
Exercises on using Osnap commands as Endpoint, Intersection, Nearest, Midpoint,
Tangent, Center.
10
Exercises on using Layers as Create new layer, Assign layer color, Assign layer
linetype.
11
Exercises on using dimensions - Styling Dimensions, Adding Dimensions, Using
Inquiry Commands, Adding Dimension Objects, Adding and Styling Multileaders,
Editing Dimensions
12
Exercises on using Creating and Editing Text- Creating Text Styles, Writing Lines
of Text, Creating Text to Fit, Justifying Text, Transforming and Creating Text,
Editing Text.
13
Exercises on using Zoom Commands- Zoom realtime, Zoom window, Zoom
previous, Zoom all, Pan realtime
14&15 Exercises on using Hatching and Gradients- Specifying Hatch Areas, Picking Points
to Determine Boundaries, Selecting Objects to Define Boundaries, Associating
Hatches with Boundaries , Hatching with Patterns, Specifying Properties, Separating
Hatch Areas, Hatching with Gradients
16
Exercises on using Printing and Plotting - Configuring Output Devices, Setting Up a
System Printer, Setting Up an AutoCAD Plotter, Plotting in Modelspace, Plotting
Layouts in Paperspace, Exporting to an Electronic Format
17-19 Introduction to Modeling – type of modeling – 2D wire frame, 3D wire frame,
surface modeling, solid modeling. Exercises on using 3D primitives, Extrude,
Revolve command, subtract, union 3D drawing by using User co-ordinate systems
20-21
Working drawing of connecting rods (I.C. Engine) with the application of
tolerances. Using CAD.
34
TRADE: Mechanic Motor Vehicle
LIST OF TOOLS & EQUIPMNT
A. TRAINEES TOOL KIT per 4 Trainees FOR 20 TRAINEES +1 ISTRUCTOR
Sl.No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
Sl.No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
Item with specification
Qty (Nos.)
(5+1)
Allen Key set of 12 pieces (2mm to 14mm)
Caliper inside 15 cm Spring
6
Calipers outside 15 cm spring
6
Center Punch 10 mm. Dia. x 100 mm.
6
Dividers 15 cm Spring
6
Electrician Screw Driver 250mm
6
Hammer ball peen 0.5 kg with handle
6
Hands file 20 cm. Second cut flat
6
Philips Screw Driver set of 5 pieces (100 mm to 300 mm)
6
Pliers combination 20 cm.
6
Screw driver 20cm.X 9mm. Blade
6
Screw driver 30 cm. X 9 mm. Blade
6
Scriber 15 cm
6
Spanner D.E. set of 12 pieces (6mm to 32mm)
6
Spanner, ring set of 12 metric sizes 6 to 32 mm.
6
Spanners socket with speed handle, T-bar, ratchet and universal upto 32
6
mm set of 28 pieces with box
Steel rule 30 cm inch and metric
6
Steel tool box with lock and key (folding type) 400x200x150 mm
6
Wire cutter and stripper
6
B. Tools Instruments and General Shop outfits
Item with specification
Qty. (Nos)
AC alternator slip ring puller
1
Adjustable spanner (pipe wrench 350 mm)
2
Air blow gun with standard accessories
1
Air Brake Assembly
1.
Air impact wrench with standard accessories
4
Air ratchet with standard accessories
4
Allen Key set of 12 pieces (2mm to 14mm)
4
Alternator assembly used for LMV
2
Ammeter 300A/ 60A DC with external shunt
4
Angle plate adjustable 250x150x175
1
Angle plate size 200x100x200mm
2
Anti theft device
1
Anvil 50 Kgs with Stand
1
Auto Electrical test bench
1
Battery –charger
2
Belt Tensioner gauge
1
Blow Lamp 1 litre
2
Caliper inside 15 cm Spring
4
Calipers outside 15 cm spring
4
Car Jet washer with standard accessories
1
35
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
Carburetor – Solex, Mikuny for dismantling and assembling
Carburetor repair tool kit
Chain Pulley Block-3 ton capacity with tripod stand
Chisel 10 cm flat
Chisels cross cut 200 mm X 6mm
Circlip pliers Expanding and contracting type 15cm and 20cm each
Clamps C 100mm
Clamps C 150mm
Clamps C 200mm
Cleaning tray 45x30 cm.
Coil spring compressor for suspension spring
Compression testing gauge suitable for diesel Engine with standard
accessories
Connecting rod alignment fixture
Constant Mesh Gear box with stand for Dismantling and assembly.
Copper bit soldering iron 0.25 Kg
Cut section Model of Mock layout of a motor car –electrical system
working model
Cut section models of shock absorbers
Cut section of cross ply and radial tyres
Cut section working model of automatic transmission Gear box
Cut section working model of centrifugal clutch assembly.
Cut section working model of Diaphragm clutch assembly.
Cut section working model of Single plate clutch assembly.
Cylinder bore gauge capacity 20 to 160 mm
Cylinder liner- Dry & wet liner, press fit & slidefit liner
DC Ohmmeter 0 to 300 Ohms, mid scales at 20 Ohms
Demonstration board of 2W Ignition system, ignition coil
Demonstration board of electronic Ignition system, ignition coil
Demonstration board of MPFI system
Depth micrometer 0-25mm
Dial gauge type 1 Gr. A (complete with clamping devices and with
magnetic stand)
Different type of Engine Bearing model
Different type of piston model
Disk brake with caliper assembly
Distributor –Duel advance type, reluctance type
Dividers 15 cm Spring
Drift Punch Copper 15 Cm
Drill point angle gauge
Drill twist 1.5 mm to 15 mm (various sizes) by 0.5 mm
Drum brake assembly
Electric Soldering Iron 230 V 60 watts 230 V 25 watts
Electric testing screw driver
Engineer’s square 15 cm. Blade
Engineers stethoscope
Executive Auto Electrical tool kit
Feeler gauge 20 blades (metric)
36
1 each
1
1
4
4
4
2
2
2
4
1
2
1
1
4
1 set
1
1
1
1
1
1
4
1 each
2
1
1
1
4
4
1 set
1each
2
1 each
4
4
1
4
1
2 each
4
4
1
1
4
66.
67.
68.
69.
70.
71.
72.
73.
74.
75.
76.
77.
78.
File flat 20 cm bastard
File, half round 20 cm second cut
File, Square 20 cm second cut
File, Square 30 cm round
File, triangular 15 cm second cut
Files assorted sizes and types including safe edge file (20 Nos)
Flat File 25 cm second cut
Flat File 35 cm bastard
Front axle ( Rzeeppa Joint) with stand for Dismantling and assembly
Fuel feed pump for diesel
Fuel injection pump (Diesel) inline
Fuel injection pump dismantling tool kit /Universal Vice
Fuel injection pump, VE pump / Distributor fuel rotary pump (DPC)
pumps / along with special tools and accessories.
4
4
4
4
4
2 set
4
4
1
1
1
1
1 each
79.
80.
81.
82.
83.
84.
85.
86.
87.
88.
89.
90.
91.
92.
93.
94.
1
1 set
4
5 sets
2
1
2
1
2
10
4
5
4
4
4
2
96.
97.
98.
Full floating axle and semi-floating axle assembly
Functional/experiment model of different type of sensors.
Garage stand
Gloves for Welding (Leather and Asbestos)
Glow plug tester
Granite surface plate 1600 x 1000 with stand and cover
Grease Gun
Grease Gun heavy duty trolley type 10 kg capciaty
Growler
Hacksaw frame adjustable 20-30 cm
Hammer Ball Peen 0.75 Kg
Hammer Chipping 0.25 Kg
Hammer copper 1 Kg with handle
Hammer Mallet
Hammer Plastic
Hand operated crimping tool (i) for crimping up to 4mm and (ii) for
crimping up to 10mm
Hand reamers adjustable 10.5 to 11.25 mm, 11.25 to 12.75 mm, 12.75
to 14.25 mm and 14.25 to 15.75 mm
Hand Shear Universal 250mm
Hand vice – 37 mm
Hollow Punch set of seven pieces 6mm to 15mm
99.
100.
101.
102.
103.
104.
105.
106.
107.
108.
Horn and Horn relay
Impact screw driver
Injector – Multi hole type, Pintle type
Injector cleaning unit
Injector testing set (Hand tester)
Insulated Screw driver 20 cm x 9mm blade
Insulated Screw driver 30 cm x 9mm blade
Left cut snips 250mm
Lifting jack screw type 3 ton, 5ton & 20 Ton capacity
Magneto spanner set with 8 spanners
109.
Magnifying glass 75mm
95.
1 sets
2
2
2 sets each
2
2
4 each
1
1
4
4
4
1 each
1 set
2
37
110.
111.
112.
113.
114.
115.
116.
117.
118.
119.
120.
121.
122.
123.
124.
125.
126.
127.
128.
129.
130.
131.
132.
133.
134.
135.
136.
137.
138.
139.
140.
141.
142.
143.
144.
145.
146.
147.
148.
149
150
151
152
153
154
155
156
157
Marking out table 90X60X90 cm.
Multimeter digital
Multi-point fuel injection pump
Oil can 0.5/0.25 liter capacity
Oil pump for dismantling and assembling.
Oil Stone 15 cm x 5 cm x 2.5 cm
Oscilloscope 20MHz
Outside micrometer 0 to 25 mm
Outside micrometer 25 to 50 mm
Outside micrometer 50 to 75 mm
Outside micrometer 75 to 100 mm
Petrol nozzle
Philips Screw Driver set of 5 pieces (100 mm to 300 mm)
Pipe cutting tool
Pipe flaring tool
Piston ring compressor
Piston Ring expander and remover.
Piston Ring groove cleaner.
Pliers combination 20 cm.
Pliers flat nose 15 cm
Pliers round nose 15 cm
Pliers side cutting 15 cm
Portable electric drill Machine
Prick Punch 15 cm
Punch Letter 4mm (Number)
Radiator cut section-cross flow
Radiator cut section-down flow
Radiator pressure cap
Rear axle full floating type with stand for Dismantling and assembly
Right cut snips 250mm
Rivet sets snap and Dolly combined 3mm, 4mm, 6mm
Scraper flat 25 cm
Scraper half round 25 cm
Scraper Triangular 25 cm
Scriber 15 cm
Scriber with scribing black universal
Set of stock and dies – Metric
Shear Tin Man’s 450 mm x 600mm
Sheet Metal Gauge
Sher Tinmans 300mm
Soldering Copper Hatchet type 500gms
Solid Parallels in pairs (Different size) in Metric
Spanner Clyburn 15 cm
Spanner D.E. set of 12 pieces (6mm to 32mm)
Spanner T. flocks for screwing up and up-screwing inaccessible
positions
Spanner, adjustable 15cm.
Spanner, ring set of 12 metric sizes 6 to 32 mm.
Spanners socket with speed handle, T-bar, ratchet and universal upto
32 mm set of 28 pieces with box
38
1
5
2
4
2
1
1
4
4
1
1
2
2
2
2
2
2
2
2
2
2
2
1
4
2 set
1
1
2
1
2
2
2
2
2
2
2
2 sets
2
2
4
2
2
1
4
2
2
4
2
158
159
160
161
162
163
164
Spark lighter
Spark plug spanner 14mm x 18mm x Size
Starter motor axial type, pre-engagement type & Co-axial type
Steel measuring tape 10 meter in a case
Steel rule 15 cm inch and metric
Steel rule 30 cm inch and metric
Steering assembly - 1.Rack & pinion, 2.Worm & roller 3. Recirculating
ball, 4.Power steering
2
2
1each
4
4
4
1 each
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
Straight edge gauge 2 ft.
Straight edge gauge 4 ft.
Stud extractor set of 3
Stud remover with socket handle
Surface gauge with dial test indicator plunger type i.e. 0.01 mm
Synchronous Gear box with stand for Dismantling and assembly.
Tachometer (Counting type)
Tandem master cylinder with booster
Taps and Dies complete sets BSF
Taps and wrenches - metric
Telescope gauge
Temperature gauge with sensor 0-100 deg c
Tester sparking plug ‘NEON’ Type
Thermostat
Thread pitch gauge metric, BSW
Timing lighter
Toe-in, toe-out gauge
Torque wrenches 5-35 Nm, 12-68 Nm & 50-225 Nm
Trammel 30 cm
Tread wear indicator
Tubed tyre of car, trucks & motorcycle
Tubeless tyre of cars & trucks
Tubeless tyre repair kit
Turbocharger cut sectional view
Tyre & split rim wheel assembly
Tyre pressure gauge with holding nipple
Universal puller for removing pulleys, bearings
V’ Block 75 x 38 mm pair with Clamps
Vacuum assisted hydraulics brake assembly with vacuum booster
Vacuum gauge to read 0 to 760 mm of Hg.
Valve Lifter
Valve spring compressor universal.
vernier caliper 0-300 mm with least count 0.02mm
Vice grip pliers
Water pump for dismantling and assembling
Wheel cylinder
Wiper motor assembly
Wire Gauge (metric)
Work bench 250 x 120 x 60 cm with 4 vices 12cm Jaw
2
2
2 sets
1
4
1
1
4
1 set
2 sets
4
2
1
2
2
2
1set
1 each
2
1
1
1
39
1
1
2
1
2
1
2
1
1
4
2
4
4
2
2
4
204
205
206
207
Sl.No.
1.
2.
3.
4.
5.
6.
Working Model of power windows
Working model of torque converter
4 Point relays
5 Point relays
C. General Installation/ Machineries
Item with specification
1
1
2
2
Qty (Nos.)
1
1
1
1
1
1
9.
Air bag simulator
Air conditioned CRDI Vehicle in running condition -LMV
Air conditioning service Unit (Car)
Air conditioning trainer kit
Arbor press hand operated 2 ton capacity
Automotive exhaust 5 gas analyzer (petrol & Diesel) or Diesel Smoke
Meter
Bench lever shears 250mm Blade x 3mm Capacity
Diesel Engine – CRDI - 4 stroke for Dismantling and assembling with
swivelling stand
Diesel engine ( Running condition ) Stationary type
10.
Discrete Component Trainer / Basic Electronics Trainer
1
11.
Drilling machine bench to drill up to 12mm dia along with accessories
1
12.
13.
14.
15.
16.
Dual Magnetization Yoke : AC / HWDC, 230 VAC, 50Hz
Four stroke petrol engine with CNG setup-working condition
Gas Welding Table 1220mm x760mm
Grinding machine (general purpose) D.E. pedestal with 300 mm dia
wheels rough and smooth
Hand operated Hydraulic press
17.
18.
Heavy Commercial vehicle type (without body on frame)
Hydraulic jack HI-LIFT type -3 ton capacity, and 5 Ton capacity
19.
20.
Liquid penetrant Inspection kit
MPFI petrol engine with swiveling stand along with special tools for
dismantling and assembling
1 set
1
21.
22.
Multi Scan Tool with oscilloscope
Petrol Engine(2-stroke) Motor Cycle/Scooter along with special tools
and accessories
Pipe Bending Machine (Hydraulic type) 12mm to 30mm
Pneumatic rivet gun with standard accessories
Spring tension tester
1
1
Tin smiths bench folder 600 x 1.6mm
Transfer case with stand for Dismantling and assembly.
Trolley type portable air compressor single cylinder with 45 liters
capacity Air tank, along with accessories & with working pressure 6.5
kg/sq cm
1
1
1
7.
8.
23.
24.
25.
26.
27.
28.
40
1
1
1 set
1
2
1
1
1
1 each
1
2
1
29.
30.
31.
32.
33.
34.
35.
36.
37.
Tube/ tyre vulcanizing machine
Two post car lift – capacity 4000 kg
Tyer Changer Machine
Ultrasonic Injection cleaning equipment
Welding plant Oxy-Acetylene complete ( high pressure)
Welding Transformer ( 150-300 Amps)
Wheel alignment Machine –computerised 3D
Wheel balancing machine
Working Condition of Diesel Engine – CRDI - 4 stroke Engine
Assembly with fault simulation board
1
1
1
1
1
1
1
1
1
38.
Working Condition of Petrol MPFI Engine Assembly with fault
simulation board
D. List of consumable:
Description
1
Sl.
No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
Quantity
Automatic Transmission oils
Battery- SMF
Brake fluids
Chalk, Prussian blue.
Chemical compound for fasteners
Diesel
Different type gasket material
Different type of oil seal
Drill Twist (assorted)
Emery paper - 36–60 grit , 80–120
Engine coolant
Engine oil
Gear oils
Gloves for Welding (Leather and Asbestos)
Hacksaw blade (consumable)
Hand rubber gloves tested for 5000 V
Holders, lamp teakwood boards, plug sockets,
solders, flux wires and cables batteries round
consumable blocks and other consumables as
required
As required
As required
As required
As required
As required
As required
As required
As required
As required
As required
As required
As required
As required
5 sets
As required
5 pair
As required
Hydrometer
Lapping abrasives
Leather Apron
Petrol
Power steering oil
Radiator Coolants
Safety goggles
Steel wire Brush 50mmx150mm
4
As required
5
As required
As required
As required
As required
5
41
E. Workshop Furniture
Sl.
No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Description
Quantity
12.
13.
14.
15.
16.
17.
18.
19.
Book shelf (glass panel) 6½ ‘ x 3’ x 1½’
Computer Chair
Computer Table
Desktop computer and related MS office software
Discussion Table 8’ x 4’ x 2½ ‘
Fire Extinguishers, first- aid box
Instructional Material – NIMI Books/Ref.books
Internet connection with all accessories
Laser printer
LCD projector/ LED /LCD TV (42”)
Multimedia DVD for Automotive
application/subjects
Online UPS 2KVA
Stools
Storage Rack 6½ ‘ x 3’ x 1½’
Storage shelf 6½ ‘ x 3’ x 1½’
Suitable class room furniture
Suitable Work Tables with vices
Tool Cabinet - 6½ ‘ x 3’ x 1½’
Trainees locker 6½ ‘ x 3’ x 1½’
Sl. No.
1.
2.
3.
4.
5.
TRAINEE’S TOOLS KIT
Name of the items
Draughtsman drawing instrument box
Set square celluloid 45⁰ (250 X 1.5 mm)
Set square celluloid 30⁰-60⁰ (250 X 1.5 mm)
Mini drafter
Drawing board
(700mm x500 mm) IS: 1444
As required
1+1
1+1
1+1
2
As required
As required
As required
1
1
As required
1
21
As required
As required.
As required
As required
2
2 Nos. to accommodate 20
Lockers
List of tools & Equipment for the Trade of
Mechanic Motor Vehicle - Engineering Drawing
(Note : Facilities available in Draughtsman trade can be utilized)
Quantity
20+1 set
20+1 set
20+1 set
20+1 set
20+1 set
GENERAL MACHINERY SHOP OUTFIT
Sl. No.
1.
2.
3.
4.
5.
6.
7.
8.
Name & Description of Machine
Quantity
Draughtsman table
Draughtsman stool
Computer Latest version compatible for running Auto CAD
software, preloaded with windows and 20” colour Monitor.
Plotter (Max. A3 size) (Max. A0 size)
Laser Jet printer latest model
UPS - 5 KVA
Computer table
Computer chairs
42
20 Nos.
20Nos.
10Nos
1 No.
1 No.
2 Nos.
10 Nos.
10 Nos.
43
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement