INOXPA SWFI PROLAC B, C, D, E, F, G, H pump Installation, service and maintenance instructions
Below you will find brief information for SWFI PROLAC SWFI PROLAC. This manual provides comprehensive instructions for the installation, operation, and maintenance of your new INOXPA SWFI PROLAC centrifugal pump. It covers topics such as pump reception, transport, location selection, piping, electrical installation, start-up procedures, troubleshooting, general maintenance, cleaning (including CIP and SIP), and detailed disassembly/assembly instructions. The manual also includes technical specifications, weight charts, and dimension drawings for both IEC and NEMA motor versions. Ensure safe operation by strictly adhering to the safety guidelines provided.
Advertisement
Advertisement
INSTALLATION,
SERVICE AND MAINTENANCE INSTRUCTIONS
SWFI PROLAC PUMP
INOXPA, S.A.
c/Telers, 54 Aptdo. 174
E-17820 Banyoles
Girona (Spain)
Tel. : (34) 972 - 57 52 00
Fax. : (34) 972 - 57 55 02
Email: [email protected] www.inoxpa.com
Original Manual
01.003.30.00EN_RevD
ED. 2010/09
EC
DECLARATION OF CONFORMITY
(according to Directive 2006/37/CE, annex II, part A)
Manufacturer:
INOXPA, S.A.
C/ Telers, 54
17820 Banyoles (Girona) - SPAIN
Hereby declares, that the product:
CENTRIFUGAL PUMP PROLAC SWFI
Name Type
conforms to the specifications of the Council Directive:
Machine Directive
2006/42/CE, and complies with the essential requirements of the
Directive and Harmonised Standards:
UNE-EN ISO 12100-1/2:2004
UNE-EN 809/AC:2001
UNE-EN ISO 13857:2008
UNE-EN 953:1997
UNE-EN ISO 13732-1:2007
Low Voltage Directive
2006/95/EC (what repeal 73/23/CEE Directive), and are
conforms with UNE-EN 60204-1:2006 and UNE-EN 60034-1:2004
EMC Directive
2004/108/EC (what repeal 89/336/CEE Directive), and are conforms
with UNE-EN 60034-1:2004
In compliance with the Regulations (CE) nº 1935/2004, relating to materials and articles intended to come into contact with foodstuff (repeal Directive 89/109/CEE), the materials in contact with the product do not transfer their components in quantities which may jeopardise consumer’s health or safety
Banyoles, 2012
1. Safety
1.1. INSTRUCTION MANUAL
This instruction manual contains information on the reception, installation, operation, fitting, stripping and maintenance for the
SWFI PROLAC PUMP.
The information given herein is based on the most up-to-date data available.
INOXPA reserves the right to modify this instructions manual without having to give prior notice.
1.2. START-UP INSTRUCTIONS
This instruction manual contains vital and useful information for properly operating the pump and for keeping it in good running condition.
Not only should the safety instructions set forth in this chapter be carefully read before putting the pump into operation, but those concerned must also familiarize themselves with the operating features of the pump and strictly adhere to the instructions given herein. It is extremely important that these instructions be kept in a set place near the installation.
1.3. SAFETY
Warning signs
Danger for people in general
Danger of injury caused by rotating parts of the equipment.
Danger! Electricity.
Danger! Suspended loads
Danger! Caustic or corrosive agents.
Danger to the proper operating of the machine
Obligation to ensure safety at work.
1.4. GENERAL SAFETY INSTRUCTIONS
Use safety goggles obligatory.
Please read the instruction manual carefully before installing and commissioning the pump. Should you have any doubts o queries, contact INOXPA.
1.4.1. During the installation
You must always bear in mind the
Technical Specifications
set forth in Chapter 8.
Do not put the pump into operation before connecting it to the pipes.
Do not put the pump into operation if the cover of the pump has not been fitted and the impeller fixed in the pump.
Check that the motor specifications are correct, especially if there is a special risk of explosion due to the work conditions.
During the installation procedure, all the electrical work must be carried out by duly authorized personnel.
1.4.2. During operation
You must always bear in mind the
Technical Specifications
have been set must NEVER be exceeded.
set forth in Chapter 8. The limit values that
NEVER touch the pump or pipes whenever the pump is being used to decant hot liquids or during the cleaning procedure.
ED. 2010/09 1.Safety 3
The pump has moving parts. Do not put your fingers into the pump when it is operating.
NEVER work with the suction and the delivery valves shut off.
NEVER directly sprinkle the electric motor with water. Standard motor protection is IP-55: dust and water sprinkling protection.
1.4.3. During maintenance
You must always bear in mind the
Technical Specifications
set forth in Chapter 8.
NEVER strip the pump down until the pipes have been drained. Remember that there will always be some liquid left in the pump casing (if it has not been fitted with a drain). Always remember that the liquid that has been pumped may be dangerous or subject to high temperatures. For situations of this type, please consult the prevailing regulations in the country in question.
Do not leave loose parts on the floor.
ALWAYS turn the power supply to the pump off before embarking on maintenance work. Take out the fuses and disconnect the wires.
All electrical work must be carried out by duly authorized personnel.
1.4.4. In accordance with the instructions
Any failure to comply with the instructions could lead to a hazard for the operators, the atmospheric conditions of the room, and the machine, and it could lead to a loss to any right to make a claim for damages.
Such non-compliance could bring with it the following risks:
• Important operating failures of the machine / plant.
• Failure to comply with specific maintenance and repair procedures.
• Potential electrical, mechanical and chemical hazards.
• Atmospheric conditions in the room could be hazardous due to the release of chemical substances.
1.4.5. Warranty
We wish to point out that any warranty issued will be null and void and that we are entitled to an indemnity for any civil liability claim for products which might be filed by third parties if:
• Operation and maintenance work has not been done following the corresponding instructions; the repairs have not been made by our personnel or have been made without our written authorization;
• Modifications are made to our material without prior written authorization;
• The parts or lubricants used are not original INOXPA parts/lubricants;
• The material has been improperly used due to error or negligence or have not been used according to the indications and the intended purpose.
• The parts of the pump have been damaged as a result of having been exposed to strong pressure as there was no safety valve.
The General Delivery Terms which you have already received are also applicable.
No modification can be made to the machine without the prior consent of the manufacturer. For your safety, use spare parts and original accessories.
The use of other parts exempts the manufacturer from any and all responsibility.
Any change in operating conditions can only be done with the prior written consent of INOXPA.
In the event of doubt or should you require a fuller explanation on particular data (adjustment, assembly, disassembly...), please do not hesitate to contact us.
ED. 2010/09
2. Index
1.
Safety
1.1. Instruction manual .......................................................................................................... 3
1.2. Start-up instructions ........................................................................................................ 3
1.3. Safety ............................................................................................................................. 3
1.4. General safety instructions ............................................................................................... 3
2.
Index
3.
General Information
3.1. Description ...................................................................................................................... 6
3.2. Principle of operation ....................................................................................................... 6
3.3. Application ...................................................................................................................... 6
4.
Installation
4.1. Pump reception ............................................................................................................... 8
4.2. Transport and storage ..................................................................................................... 8
4.3. Location .......................................................................................................................... 9
4.4. Pipes .............................................................................................................................. 9
4.5. Electrical installation ........................................................................................................ 9
5.
Start-up
5.1. Start-up .........................................................................................................................10
6.
Operating problems
7.
Maintenance
7.1. General maintenance ......................................................................................................12
7.2. Storage ..........................................................................................................................12
7.3. Cleaning ........................................................................................................................12
7.4. Flushing circuit ...............................................................................................................13
7.5. Pump disassembly/assembly ...........................................................................................14
8.
Technical Specifications
8.1. Technical specifications ...................................................................................................19
8.2. Weights .........................................................................................................................20
8.3. SWFI PROLAC PUMP with IEC motor dimensions ..............................................................21
8.4. SWFI PROLAC PUMP with NEMA motor dimensions ...........................................................22
8.5. SWFI PROLAC PUMP with IEC motor ................................................................................23
8.6. SWFI PROLAC PUMP with IEC motor parts list ..................................................................24
8.7. SWFI PROLAC PUMP with NEMA motor ............................................................................25
8.8. SWFI PROLAC PUMP with NEMA motor parts list ..............................................................26
8.9. SWFI PROLAC PUMP double mechanical seal ....................................................................27
2.Index 5
3. General Information
6
3.1. DESCRIPTION
The sanitary centrifugal pumps in the SWFI PROLAC series are manufactured using AISI 316(1.4404) stainless steel die-pressed steel plate with a Ra ≤ 0,5 μm interior finish and Ra ≤ 0,8μm exterior finish, and later electro-polished finish.
The SWFI PROLAC centrifugal pump has a compact construction, monoblock, axial intake, radial discharge, and sanitary-type connections. These series have the discharge port at 45º for self- purging and a drainage in the bottom part of the pump casing. The standard connections are the Raccord Clamp. The impeller is of open design and made of one single piece. The mechanical seal is balanced and fully sanitary; the springs are external to avoid contact with the product.
The motor conforms to the IEC standard with a stainless steel facing. IP-55 protection. Class-F insulation. Three-phased power supply with 220-240 / 380-420 / 660 V at 50Hz, depending on the power source. The motors can be ordered for working in explosion hazardous environments. Depending on environmental conditions, the motors can be explosion-proof (EExd) or of enchanced safety (EExe).
The SWFI PROLAC series also can be ordered in NEMA version.
The SWFI PROLAC series has been specially developed to respond to all hygienic requirements in the food industry. For this reason, they are designed according to the American 3-A Sanitary Standards.
As regards hygiene, reliability and sturdiness, the complete range satisfies all requirements set by the aforesaid industry.
Thanks to its design, there is optimal interchangeability of parts between the different pumps.
This equipment is suitable for his use in food process.
3.2. PRINCIPLE OF OPERATION
The rotor or impeller, situated in the housing, rotates solidly fixed to the pump shaft and consists of a given number of blades, depending on the pump model.
The impeller blades transmit energy to the fluid in the form of kinetic and pressure energy.
The pump is not reversible by simple inversion of the direction of rotation. The direction of rotation is clockwise when the pump is seen from the rear part of the motor.
3.3. APPLICATION
In general terms, SWFI PROLAC pumps, at least in their standard version, are mainly used in the food industry to decant liquids.
Each different type of pump has special hydraulic features in accordance with the pump impeller diameter and various speeds.
In the curves reflecting the characteristics, we are also given the required NPSH and the absorbed power.
3.3.1. Field of application
3.General Information ED. 2010/09
Each pump has a limited field of application. The pump in question was selected for certain pumping conditions at the time the order was made. INOXPA is not liable for any damages that might arise if the information furnished by the purchaser is incomplete (nature of the liquid, RPM…).
ED. 2010/09 3.General Information 7
4. Installation
4.1. PUMP RECEPTION
INOXPA is not responsible for any deterioration of the material as a result of its transportation or unpacking. Visually check that the packing has not suffered any damage.
The pump will be accompanied by the following documentation:
• Dispatch notes.
• Pump Instruction and Service Manual.
• Motor Instruction and Service Manual (*).
• (*) If the pump has been supplied with a motor from INOXPA.
Unpack the pump and check the following:
• The pump drainage connection and pump suction and delivery connections, removing the remains of any packing material.
• Check that the pump and the motor have not suffered any damage.
• Should the pump not be in proper condition and/or does not have all the parts, the haulier must draw up a report as soon as possible with regard to the same.
4.1.1. Pump identification and marking
Serial number
Pump plate
4.2. TRANSPORT AND STORAGE
SWFI PROLAC pumps are quite often too heavy to be put into their storage space manually.
Lift the pump as is shown below:
4.3. LOCATION
Position the pump as near as possible to the suction tank, and whenever possible below the level of the liquid.
Place the pump in such a way that there is enough space around it to provide access both to the same and to the motor.
(See
Chapter 8
.
Technical specifications
to consult dimensions and weights).
Place the pump on a level and flat surface.
The basement must be rigid, horizontal and against any vibration.
Install the pump in such a way that it can be properly ventilated. If the pump is to be installed outside, it must be done so under cover. Its positioning must enable easy access for any inspection and maintenance operations that may need to be carried out.
4.4. PIPES
• In general, suction and delivery pipes should be fitted in straight stretches, with the minimum amount of elbows and accessories, in order reduce, as far as possible, any load loss that might be produced by friction.
• Make sure that the pump mouths are well aligned with respect to the piping, and that they are similar in diameter to that of the pipe connections.
• Position the pump are near as possible to the suction tank, and whenever possible below the level of the liquid, or even lower with respect to the tank in order for the static suction head be at its maximum.
• Place brackets for the piping as near as possible to the suction and delivery mouths of the pump.
4.4.1. Shut-off valves
The pump can be isolated for the purpose of carrying out maintenance work. To this end, shutoff valves should be fitted at the pump’s suction and delivery connections.
These valves must ALWAYS be open whenever the pump is operating.
4.5. ELECTRICAL INSTALLATION
Leave the connecting of the electrical motors to qualified personnel.
Take the necessary measures to prevent any breakdowns in the connections and wires.
The electrical equipment, the terminals and the components of the control systems may still carry an electric charge even when disconnected. Contact with them may put the safety of operators at risk, or cause irreparable damage to the material.
Before maneuvering the pump, make sure that the electric box is switched off.
• Connect the motor in accordance with the instructions supplied by the manufacturer of the same.
• Check the direction of the rotation (see the signaling label on the pump).
Put the pump motor into operation momentarily. Make sure, by looking at the pump from the rear, that the motor’s ventilator is rotating in a clockwise direction.
Check ALWAYS the direction of the motor’s rotation with liquid inside the pump.
For the models with sealing chamber, make sure always that it is filed of liquid before checking the rotating direction.
ED. 2010/09 4.Installation 9
5. Start-up
Before putting the pump into operation read carefully the instructions on installation given in
Chapter 4.
5.1. START-UP
Installation
Read Chapter 8.
Technical Specifications
carefully. INOXPA will not assume responsibility for any improper or incorrect use of the equipment.
Do not touch the pump or the piping while it is pumping products at a high temperature.
5.1.1. Checks to be carried out before putting the pump into operation
• Completely open the pipes’ suction and delivery shut-off valves.
• If the liquid fails to flow toward the pump, fill it with the liquid to be pumped.
The pump must NEVER rotate without liquid.
• Check that the rotation direction of the motor is correct.
5.1.2. Checks to be carried out on putting the pump into operation
• Check to make sure that the pump is not making any strange noises.
• Check to see if the absolute inlet pressure is sufficient, in order to avoid cavitation in the pump. Consult the curve for the minimum required pressure above the steam pressure (NPSHr).
• Monitor the delivery pressure.
• Check that there are no leaks in the sealed areas.
A shut-off valve should not be used in the suction pipe to regulate the flow rate. It must be completely open during operation.
Monitor motor consumption in order to avoid a circuit overload.
Reduce the flow and the power consumed by the motor:
• Regulating the flow to the pump delivery.
• Decreasing motor speed.
6. Operating problems
The table given below provides solutions to problems that might arise during pump operation. With respect to the same, it is assumed that the pump has been properly installed and has been correctly selected for the application in question.
Should there be a need for technical service please contact INOXPA.
Operating problems
Overloading of motor.
Insufficient flow rate or pressure in pump.
No pressure on the discharge side.
Irregular discharge flow rate / pressure.
Noise and vibrations.
The pump gets clogged.
Overheating of the pump.
Abnormal wear.
Leak in mechanical seal.
Probable causes
8, 9, 13, 20, 21.
1, 2, 4, 5, 7, 9, 10, 17, 19.
2, 3, 6, 18.
1, 2, 4, 5, 6, 9.
2, 4, 5, 6, 7, 8, 9, 10, 13, 14, 15, 20, 21.
9, 10, 13, 15, 20, 21.
8, 9, 10, 13, 15, 20, 21.
4, 5, 10, 15, 20, 21.
11, 12, 16.
Probable causes
1 Wrong rotation direction.
2 Insufficient NPSH.
3 Non-purged pump.
4 Cavitation.
5 The pump is sucking air.
6 Obstructed suction piping.
7 Delivery pressure is too high.
8 Flow is too high.
9 The viscosity of the liquid is too high.
10 The temperature of the liquid is too high.
11 Mechanical seal either damaged or worn.
13 The impeller is rubbing.
14 Pressure in the pipes.
15 There are foreign bodies in the liquid.
16 The tension of the mechanical seal spring is too low.
17 The pump speed is too low.
18 The suction shutoff valve is closed.
19 Delivery pressure is too low.
20 Pressure on the pipes.
21 Pump and/or motor not fixed to the base-plate.
Solutions
Change the direction of the rotation.
Increase the NPSH available: - Raise the suction tank. - Lower the pump. - Decrease the steam tension. - Increase the diameter of the suction piping. - Shorten and simplify the suction piping.
Purge or fill.
Increase the suction pressure.( See Number 2 also)
Check the suction piping and all of its connections.
Check the suction piping and the filters, if there are any.
If necessary, decrease the load losses by increasing the diameter of the piping, for example.
Decrease the flow: - Reduce the flow by means of a diaphragm. -
Partially close off the delivery valve. - Trim the impeller. -
Decrease the speed.
Decrease the viscosity by heating the liquid, for example.
Decrease the temperature of the liquid by cooling it.
Replace the seal.
Fit more suitable O-ring gaskets by consulting the supplier with respect to the same.
- Lower the temperature. - Lower suction pressure. - Adjust impeller / cover set.
Connect the pipes to the pump without pressure.
Place a filter at the suction piping.
Adjust in accordance with the instructions given herein.
Increase the speed.
Check and open.
Increase the pressure: - Increase the diameter of the impeller. -
Increase pump speed.
Connect the pipes to the pump without pressure and align the coupling.
Affix the pump and/or the motor to the base-plate, check to see if the pipes are connected without pressure and align the coupling.
If the problems persist stop using the pump immediately. Contact the pump manufacturer or his representative.
ED. 2010/09 6.Operating problems 11
7. Maintenance
7.1. GENERAL MAINTENANCE
This pump, as with any other machine, needs to be maintained. The instructions contained in this manual deal with the identification and replacement of the spare parts. These instructions have been drawn up by maintenance staff and are destined for those people who are responsible for supplying spare parts.
Read carefully Chapter 8.
Technical Specifications
.
All the parts or materials that are changed must be duly eliminated/recycled in accordance with the prevailing directives in each area.
ALWAYS disconnect the pump before starting out on any maintenance work.
7.1.1. Check the mechanical seal
Periodically check that there are no leaks in the shaft area. Should there be any leaks in the mechanical seal area, replace the same pursuant to the instructions given in the section entitled Pump disassembly / assembly .
7.2. STORAGE
Before being stored the pump must be completely emptied of liquids. Avoid, as far as possible, the exposure of the parts to excessively damp atmospheres.
7.3. CLEANING
The use of aggressive cleaning products such as caustic soda and nitric acid may give rise to skin burns.
Use rubber gloves during the cleaning process.
Always use protective goggles.
7.3.1. Automatic CIP (cleaning-in-place)
If the pump is installed in a system fitted with a CIP process, there will be no need for stripping.
If it is not fitted with an automatic cleaning process, strip the pump pursuant to the instructions given in the section entitled
Pump disassembly / assembly
.
Cleaning solutions for CIP processes.
Only use clear water (chloride free) to mix with the cleaning agents:
a) Alkaline solution: 1% in weight of caustic soda (NaOH) to 70ºC (150ºF)
1 Kg NaOH + 100 l. water = cleaning solution or
2,2 l. NaOH al 33% + 100 l. of water = cleaning solution
b) Acid solution: 0,5% in weight of nitric acid (HNO
3
) a 70ºC (150ºF)
0,7 litres HNO
3
to 53% + 100 l. of water = cleaning solution
Monitor the concentration of cleaning solutions, it could give rise to the deterioration of the pump sealing gaskets.
In order to remove any remains of cleaning products, ALWAYS rinse the element in question with clean water after completing the cleaning process.
ED. 2010/09
7.3.2. Automatic SIP (sterilization-in-place)
The process of sterilization with steam is applied to all the equipment including the pump.
Do NOT start the pump during the process of sterilization with steam.
The parts/materials suffer no damage if the indications specified in this manual are observed.
No cold liquid can enter the pump till the temperature of the pump is lower than 60°C (140°F).
A flow by-pass is recommended to be used in order to assure the flow of sterile product after the pump.
Maximum conditions during the SIP process with steam or overheated water a)
Max. temperature: 140°C / 284°F
b) c) d)
Max. time:
Cooling:
Materials:
30 min
Sterile air or inert gas
EPDM / PTFE (recommended)
FPM / NBR (not recommended)
7.4. FLUSHING CIRCUIT
The SWFI PROLAC pumps ordered with double mechanical seal also have the flushing circuit option (to be ordered apart).
These series have the self-purging feature and moreover, all the flush circuit elements self-drain completely.
The circuit’s components are:
• A needle valve to regulate the flow rate and the pressure of the mechanical seal to extend its working life.
• A check valve to prevent air form entering the circuit after vaporization.
• A manual diaphragm valve to drain the pump and the circuit.
• No “dead points”. The pump has drainage in the bottom part of the pump casing and the discharge port located at the highest point of the volute.
7.Maintenance 13
7.5. PUMP DISASSEMBLY/ASSEMBLY
7.5.1. Pump casing and impeller
Disassembly
Remove the clamping ring (15) and disassemble the pump casing (01).
Check to see that the O-ring (80A) is still in good condition.
Remove the screws (50A) and the protections (47A).
Insert open-jaw wrench in the shaft flats (05) to keep it from rotation.
Remove the blind nut (45) and the O-ring (80D).
Remove the impeller (02). If necessary, hit it with a dead blow using a plastic mallet in order to drive off the cone.
Assembly
Slide the impeller (02) over the shaft up to the rotating part of the mechanical seal.
Mount the O-ring (80D) into place and tighten the blind nut (45)
Check that the clearance between the impeller and the cover (03) remains at 0,3 - 0,5 mm so that the working pressure of the seal would be the correct one. See the following detail. If the clearance is not correct, loosen the studs (55), place correctly the shaft (05) and secure the studs.
Insert the O-ring (80A).
Fit the body (01) and fix it to the lantern (04) with the clamping ring (15).
7.5.2. Simple mechanical seal
Disassembly
Remove the rotational part from the mechanical seal (08).
Take off the pump cover (03), the fixed part of the mechanical seal (08) will remain housed in the cover.
Remove the fixed part of the mechanical seal (08).
Assembly
Fit the pump cover (03) on the lantern (04).
Check that the seals fitting dimension is as indicated, see the following table. If the clearance is not correct, loosen the studs
(55), place correctly the shaft (05) and secure the studs.
Insert the stationary part of the mechanical seal (08) into its location in the cover. Check the position of the pivot of the stationary part of the seal.
Slide the rotating part of the mechanical seal (08) over the shaft. Check that the shaft’s dragging pivot encases in its position.
Seal diameter A [mm]
5/8” 26
1” 26
1 ½” 31
ED. 2010/09
¡IMPORTANT! When assembling the new seal, be careful and mount the parts and the O-ring with soapy water in order to allow an easy glide of the parts, either the stationary part and the rotary part on the shaft.
7.Maintenance 15
7.5.3. Double mechanical seal
Disassembly
Remove the screws (52), thus freeing the lids (10 y 10A).
Remove the double seal cover (03A) and the double seal lid (10). The fixed part of the inner mechanical seal (08B) will remain housed in the double seal cover (03A).
Loosen the studs from the rotating parts of the seals (08B) till it could be slidden over the shaft, then remove it.
Remove the outer lid (10A), the fixed part of the exterior mechanical seal (08B) will remain housed in the cover.
Assembly
Fit the fixed outer part of the seal (08B) into the outer lid housing (10A).
Position the outer lid (10A) with the screws (52) in their position, leaving it losse at the end of the shaft (05A).
Slide the rotating part of the mechanical seal (08B) over the shaft and fix the studs.
Check that the assembly dimension is correct. If the dimension is not correct, loosen the studs (55), place correctly the shaft
(05) and secure the studs.
Position the lid (10) over the outer lid (10A) placing the screws (52).
Fit the fixed inner part of the mechanical seal (08B) into the double seal cover housing (03A).
Assemble the pump cover (03A) to the lantern (04) and fix it with the screws (52).
¡IMPORTANT! When assembling the new seal, be careful and mount the parts and the O-ring with soapy water in order to allow an easy glide of the parts, either the stationary part and the rotary part on the shaft.
7.5.4. Motor replacement (IEC type)
Disassembly
Remove the splash ring (82).
Loosen the studs (55) and take the shaft (05) out.
Remove the screws (50) and take out the shroud (14).
Remove the screws (52) and take the lantern (04) out.
Assembly
Position the shroud cover (14) between the lantern (04) and the motor flange (93).
Fix the ensemble with the screws (52) and the flat washers (53).
Position the shroud body (14) on the shroud cover and fix it with the screws (50).
Slide the shaft (05) over the motor shaft and fix it with the studs (55) in the groove.
Position the splash ring (82).
ED. 2010/09 7.Maintenance 17
7.5.5. Motor replacement (NEMA type)
Disassembly
Remove the splash ring (82).
Loosen the studs (55) and take the shaft (05) out.
Remove the screws (52) and take the lantern (04) out.
Remove the screws (52A) and take the leggs (07) out.
Assembly
Position the leggs (07) into the motor (93) and fix with the screws (52A) and the spring washers (53A).
Fit the lantern (04) over the motor flange (93).
Fix the ensemble with the screws (52) and the flat washers (53).
Slide the shaft (05) over the motor shaft and fix it with the studs (55) in the groove.
Position the splash ring (82).
8. Technical Specifications
8.1. TECHNICAL SPECIFICATIONS
50Hz
60Hz
Maximum flow rate (1450 min
-1
) .............................................. 140 m
3
Maximum differential pressure ................................................ 6,8 bar (100 PSI)
Maximum suction pressure ...................................................... 4 bar (58 PSI)
Maximum operating pressure ................................................. 10,8 bar (157 PSI)
Operating temperature ........................................................... -10 ºC a +140ºC (EPDM)
14 ºF a 284 ºF (EPDM)
9,5 bar (140 PSI)
4 bar (58 PSI)
13,5 bar (196 PSI)
-10 ºC a +140ºC (EPDM)
14 ºF a 284 ºF (EPDM)
Noise level ............................................................................ 60-80 dB(A) 60-80
Suction / delivery connections .……........................................... CLAMP-ISO 2852 CLAMP-ISO 2852
Whenever the noise level in the area of operation exceeds 85 dB(A) use special protection.
Materials
ED. 2010/09
Other parts in stainless steel ……............................................... AISI 304
Gaskets in contact with the product .......................................... EPDM (standar)
Other optional joint materials …………........................................ Consult your supplier
Surface finish ……….................................................................. Standard finish
Mechanical seal
Seal type ............................................................................... Single internal mecanical seal
Stationary part material .......................................................... Tungsten carbide (standar)
Fixed part material ................................................................. Silicon carbide (standar)
Gaskets material .................................................................... EPDM (standar)
Double mechanical seal
Operating pressure ................................................................. 1,5~2 bar (22~29 PSI) over the pump operating pressure
Circulation flow ....................................................................... 0,25-0,5 l/min
Temperature .......................................................................... 85º-90ºC at atmospheric pressure
8.Technical Specifications 19
8.2. WEIGHTS
PUMP
TYPE
B
S-20
C
B
S-26
E
S-28
B
C
S-35
E
C
F
C
E
S-38
G
H
IEC Motor
Kw min
-1
Pump without motor [ Kg ]
0,75 1450
1,1 2950
1,5 2950
11
2,2 2950
0,75 1450 12
3 2950
4 2950 13
5,5 2950
0,75 1450
1,1 2950
1,5 2950
2,2 2950
3 2950
4 2950
5,5 2950
15
16
1,5 1450 15,5
5,5 2950
7,5 - 9 2950
11 2950
20
1,5 1450 17
2,2 1450
3 1450 21,5
4 1450
11 2950
15 2950
18,5 2950
22 2950
33
Pump with motor [ Kg ]
24
24
28
30
25
38,5
50,5
52,5
28
28
32
34
42
54
56
34,5
71
80
86
34,5
47
50
57
120
127
139
166
PUMP
TYPE
S-20
S-26
S-28
S-35
S-38
D
C
D
E
C
D
B
C
F
G
B
C
D
B
B
C
D
NEMA Motor
Size
145 TC
182/184 TC
213/215 TC
145 TC
182/184 TC
213/215 TC
145 TC
182/184 TC
213/215 TC
145 TC
182/184 TC
213/215 TC
182/184 TC
213/215 TC
254/256 TC
284/286 TC
324/326 TC
Pump without motor [ Kg ]
21
22
23
25
19
20
16
20
27
33
10
14
15
11
15
16
15
20 8.Technical Specifications ED. 2010/09
8.3. SWFI PROLAC PUMP WITH IEC MOTOR DIMENSIONS
Dimensions with Clamp-ISO 2852
PUMP
TYPE
S-20
S-26
S-28
S-35
S-38
B
C
Motor size
80
90
DNa DNi A B C D E F G H I
∅J
2" 11/2" 53 503 74 131 165 149 235 205 325 270
B
80
E
100/112
B
80
C
E
90
112
521
61
581
72 145
165 168 235 205 325 270
190 178 275 205 375 330
11/2" 11/2" 61
498
564
107 137
165 150 235
205
190 160 275
325 270
375 330
C
F
90
132
522
77
757
104 163
165 172 235 205 325 270
230 195 320 280 445 380
C
E
G
H
90
100/112
539
605
165 189 235
205
98 184
190 199 275
325 270
375 330
160 355
218
180 425
ED. 2010/09 8.Technical Specifications 21
8.4. SWFI PROLAC PUMP WITH NEMA MOTOR DIMENSIONS
22
Dimensions with Clamp connections
PUMP
TYPE
B
S-20
Motor size
145 TC
C
182/184
D
213/215
DNa DNi
S-26
B
145 TC
C
182/184
D
213/215
S-28
S-35
S-38
B
143/145 TC
C
182/184
D
213/215
B
145 TC
C
182/184
D
213/215
C
182/184 TC
D
213/215
E
254/256
F
284/286
G
324/326
A B
440
C D E F G H I
∅J
180 200 185 140 135 170
520 74 131 218 205 230 190 150 200
610 235 250 260 216 190 245
460
630
180 220 185 140 135 170
72 145 218 220 230 190 150 200
235 265 260 216 190 245
440 180 200 185 140 135 170
520 107 137 218 200 230 190 150 200
610
460
235 250 260 216 190 245
180 225 185 140 135 170
104 163 218 225 230 190 150 200
630
520
610
235 275 260 216 190 245
218 205 230 190 150 200
235 255 260 216 190 245
795
98 184 262 290 340 254 245 306
280 295 380 280 335 356
850 308 305 420 318 360 408
8.Technical Specifications ED. 2010/09
8.5. SWFI PROLAC PUMP WITH IEC MOTOR
ED. 2010/09 8.Technical Specifications 23
8.6. SWFI PROLAC PUMP WITH IEC MOTOR PARTS LIST
Position Description
01 Pump housing
02 Impeller
03 Pump cover
04 Lantern
05 Shaft
07 Legs
07A Adjustable leg
14 Shroud
15 Clamping ring
45 Blind nut
47A Protection
50 Screw
50A Screw
24
55 Stud
80A O-ring
80D O-ring
93 Motor
8.Technical Specifications
Description
1
1
1
1
1
1
2
1
1
1
1
2
4
4
4
2
4
2
1
1
1
1
Material
AISI 316L
AISI 316L
AISI 304
-
AISI 304
AISI 316L
Plastic
A2
A2
A2
A2
A2
A2
EPDM
EPDM
EPDM
-
ED. 2010/09
8.7. SWFI PROLAC PUMP WITH NEMA MOTOR
ED. 2010/09 8.Technical Specifications 25
26
SWFI PROLAC PUMP WITH NEMA MOTOR PARTS LIST
Position Description
01 Pump housing
02 Impeller
03 Pump cover
04 Lantern
05 Shaft
07 Legs
07A Adjustable leg
14 Shroud
15 Clamping ring
45 Blind nut
47A Protection
50 Screw
50A Screw
55 Stud
80A O-ring
80D O-ring
93 Motor
8.Technical Specifications
Description
4
4
4
4
4
2
1
1
1
1
1
1
1
1
1
2
4
1
1
1
1
2
4
Material
AISI 316L
AISI 316L
AISI 304
-
AISI 304
AISI 316L
Plastic
A2
A2
A2
A2
A2
A2
A2
EPDM
EPDM
EPDM
-
ED. 2010/09
8.8. SWFI PROLAC PUMP DOUBLE MECHANICAL SEAL
Position Quantity
03A
08B
10A
23*
1
1
1
1
Description
Double seal cover
Double mechanical seal
Outer lid
Counter flange
* Only for S-35F version.
ED. 2010/09 8.Technical Specifications
Material
AISI 316L
-
AISI 316L
AISI 304
A2
EPDM
27
INOXPA, S.A.
c/ Telers, 54 – PO Box 174
17820 BANYOLES (GIRONA)
Tel: 34 972575200
Fax: 34 972575502 e-mail: [email protected] www.inoxpa.com
DELEGACIÓN LEVANTE
PATERNA (VALENCIA)
Tel: 963 170 101
Fax: 963 777 539 e-mail: [email protected]
DELEGACIÓN NORD-ESTE /
BARBERÀ DEL VALLÈS (BCN)
Tel: 937 297 280
Fax: 937 296 220 e-mail: [email protected]
DELEGACIÓN CENTRO
ARGANDA DEL REY (MADRID)
Tel: 918 716 084
Fax: 918 703 641 e-mail: [email protected]
ZARAGOZA
Tel: 976 591 942
Fax: 976 591 473 e-mail: [email protected]
DELEGACIÓN STA
GALDACANO (BILBAO)
Tel: 944 572 058
Fax: 944 571 806 e-mail: [email protected]
DELEGACIÓN SUR
JEREZ DE LA FRONTERA (CÁDIZ)
Tel / Fax: 956 140 193 e-mail: [email protected]
LA CISTÉRNIGA (VALLADOLID)
Tel: 983 403 197
Fax: 983 402 640 e-mail: [email protected]
INOXPA SOLUTIONS LEVANTE
PATERNA (VALENCIA)
Tel: 963 170 101
Fax: 963 777 539 e-mail: [email protected]
ST. SEBASTIEN sur LOIRE
Tel/Fax: 33 130289100 e-mail: [email protected]
LOGROÑO
Tel: 941 228 622
Fax: 941 204 290 e-mail: [email protected]
INOXPA SOLUTIONS FRANCE
GLEIZE
Tel: 33 474627100
Fax: 33 474627101 e-mail: [email protected]
WAMBRECHIES
Tel: 33 320631000
Fax: 33 320631001
CHAMBLY (PARIS)
Tel: 33 130289100
Fax: 33 130289101 e-mail: [email protected]
MORNINGTON (VICTORIA)
Tel: 61 3 5976 8881
Fax: 61 3 5976 8882
INOXPA ALGERIE
ROUIBA
Tel: 213 21856363 / 21851780
Fax: 213 21854431 e-mail: [email protected]
INOXPA UK LTD
SURREY
Tel: 44 1737 378 060 / 079
Fax: 44 1737 766 539 e-mail: [email protected]
INOXPA SKANDINAVIEN A/S
HORSENS (DENMARK)
Tel: 45 76 286 900
Fax: 45 76 286 909 e-mail: [email protected]
INOXPA SPECIAL PROCESSING
EQUIPMENT, CO., LTD.
JIAXING (China)
Tel.: 86 573 83 570 035 / 036
Fax: 86 573 83 570 038
INOXPA WINE SOLUTIONS
VENDARGUES (FRANCE)
Tel: 33 971 515 447
Fax: 33 467 568 745 e-mail: [email protected]
/
INOXPA SOUTH AFRICA (PTY) LTD INOXPA USA, Inc
JOHANNESBURG
SANTA ROSA
Tel: 27 117 945 223
Tel: 1 7075 853 900
Fax: 27 866 807 756
Fax: 1 7075 853 908 e-mail: [email protected]
e-mail: [email protected]
S.T.A. PORTUGUESA LDA
VALE DE CAMBRA
Tel: 351 256 472 722
Fax: 351 256 425 697 e-mail: [email protected]
IMPROVED SOLUTIONS
VALE DE CAMBRA
Tel: 351 256 472 140 / 138
Fax: 351 256 472 130 e-mail: [email protected]
INOXPA ITALIA, S.R.L.
BALLO DI MIRANO – VENEZIA
Tel: 39 041 411 236
Fax: 39 041 5128 414 e-mail: [email protected]
INOXPA INDIA PVT. LTD.
Maharashtra, INDIA.
Tel: 91 2065 008 458 [email protected]
INOXRUS
MOSCOW (RUSIA)
Tel / Fax: 74 956 606 020 e-mail: [email protected]
INOXPA UCRANIA
KIEV
Tel: 38 050 720 8692 e-mail: [email protected]
SAINT PETERSBURG (RUSIA)
Тel: 78 126 221 626 / 927
Fax: 78 126 221 926 e-mail: [email protected] [email protected]
In addition to our branches, INOXPA operates a comprehensive independent distributor network throughout the World in more than 50 countries. For further information visit our website at
www.inoxpa.com
The information contained in this brochure is for guidance only. We reserve the right to modify any material or feature without notice in advance.

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Sanitary design
- Stainless-steel construction
- Self-purging discharge port
- Compact and monoblock design
- Axial intake and radial discharge
- 3-A Sanitary Standards compliance