OMEGA 32105, 32107, 32225 Jack Stands Operating Instructions & Parts Manual

Below you will find brief information for Jack Stands 32105, Jack Stands 32107, Jack Stands 32225. These jack stands are designed for supporting partial vehicle loads, including one end of a vehicle. They are designed to support up to 10 or 22 tons of weight, depending on the model. The jack stands can be adjusted to various heights, and they feature safety mechanisms to prevent accidental lowering of the vehicle. A support bar helps to ensure stability and prevent the extension tube from accidentally slipping.

PDF Download

Document

Operating Instructions &amp; Parts Manual
Pin Style Jack Stands
Model
32105
32107
32225
Models 32105 &amp; 32107
!
Capacity per pair
10 Ton
10 Ton
22 Ton
Model 32225
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
! ADVERTENCIA
• Leer, comprender, y seguir las instrucci&oacute;nes antes
de utilizar el aparato.
• El manual de instrucci&oacute;nes y la informaci&oacute;n de
seguridad deben estar comunicado en lengua del
operador antes del uso.
• No seguir estas indicaci&oacute;nes puede causar da&ntilde;os
personales o materiales.
! WARNING
To avoid crushing and related injuries:
NEVER work on, under or around a
load supported only by a hydraulic
jack. ALWAYS use adequately rated
jack stands.
SFA Companies
http://www.omegalift.com
Read this manual and follow all the Safety Rules and Operating Instructions before using this product.
Printed in China
32105-M0 11/07
SAFETY and GENERAL INFORMATION
Save these instructions. For your safety read, understand, and follow the information provided with and on this
pair of jack stands before using. The owner and operator of this equipment shall have an understanding of the jack
stands and safe operating procedures before attempting to use. The owner and operator shall be aware that use of
this product may require special skills and knowledge. Instructions and safety information shall be conveyed in the
operator's native language before use of these jack stands is authorized. If any doubt exists as to the safe and proper
use of these jack stands, remove from service immediately.
Inspect before each use. Do not use if broken, bent, cracked, or damaged parts (including labels) are noted. Any
jack stand that appears damaged in any way, operates abnormally or is missing parts, shall be removed from service
immediately. If you suspect that the jack stand was subjected to a shock load (a load dropped suddenly, unexpectedly
upon it), immediately discontinue use until the stand has been checked by a factory authorized service center (contact
distributor or manufacturer for list of Authorized Service Centers). It is recommended that an annual inspection be
done by qualified personnel. Labels and owner’s manuals are available from manufacturer.
PRODUCT DESCRIPTION
Omega Heavy Duty Jack Stands are designed to support rated capacity, partial vehicle loads consisting of one end
of a vehicle. Use as a matched pair to support one end of a vehicle only.
!
NEVER use automotive jack stands to support both ends or one side of a vehicle!
Use only one (1) pair per vehicle. Rated capacity is per pair only!
SPECIFICATIONS
Model
32105
32107
32225
Capacity
Base Size
10 Ton
16&quot; x 16&quot;
22 Ton
9 3/4&quot; x 9 3/4&quot;
Min. Height
Max. Height
Net Weight
18 5/8&quot;
30 1/2&quot;
88 lb.
28”
47”
110 lb
12 1/4&quot;
19 7/8&quot;
64 lb.
Saddle
Height
Adjustment
Holes
Extension Tube
Height
Adjustment
Holes
Roll Pin
Extension Tube
Support Bar
Collar
Extension Tube
Support Bar
Lanyard
Collar
Saddle
Extension Tube
Corresponding Radii
Handle
Support Bar Holder
Lanyard
Base Section
Base
Support Bar Holder
Figure 1 - Models 32105 &amp; 32107 Components
Figure 2 - Model 32225 Components
2
OPERATION
! WARNING
!
Use only on areas of the vehicle as specified
by the vehicle manufacturer. Use ONLY on
vehicles whose support points are compatible with
the saddle of the jack stand. Incompatibility may result
in structural damage to the vehicle and/or jack stand.
Structural damage to either may result in sudden and
unexpected loss of load height!
• Study, understand, and follow all instructions
provided with and on this device before use.
• Rated capacity is PER PAIR! DO NOT exceed
rated capacity.
• Use as a matched pair to support one end of a
vehicle only. Use only ONE (1) PAIR per vehicle.
!
• Use only on hard, level surface.
• Center load on saddle.
Only attachments and/or adapters supplied
by the manufacturer shall be used.
1. Adjust saddle height by pulling up the extension
tube, then insert the tube support bar through the
hole on extension tube.
2. a) For models 32105 &amp; 32107: Ensure that support
bar is secured before loading. Insert support bar
into the extension tube far enough to create equal
distance of bar extending from the extension tube
on both sides.
b) For model 32225: Check to ensure support bar is
secured and nested across two corresponding radii
before loading. Ensure that support bar is inserted
completely so that bar stop engages the collar.
3. Carefully position jack stands so that load is centered
on stand’s saddle.
4. Slowly lower the vehicle onto the stands.
5. Check to ensure vehicle is secured before working
on, around or under. Use wheel chocks on all unlifted
wheels in both directions to prevent inadvertent
movement.
• Jack stands are not to be used to simultaneously
support both ends or one side of a vehicle.
• No alterations shall be made to this device.
• Failure to heed these markings may result in
personal injury and/or property damage.
PREPARATION
Assembly (refer Fig. 1 &amp; 2)
1. Make sure all parts are present. If any part is missing
or damaged, do not attempt to assemble, install or
operate the product. Contact Customer service.
2. Insert extension tube to the base.
3. For models 32105 &amp; 321007, insert roll pin into
the bottom hole of the extension tube to prevent
inadvertent removal of the extension tube.
Before Use
1. Verify that the product and the application are
compatible, if in doubt call OmegaTech. Service
(888) 332-6419.
2. Inspect stands before each use. Do not use if there are
bent, broken or cracked components noted (including
labels). Ensure that all parts move freely.
3. Read the operator's manual completely and
familiarize yourself thoroughly with the product and
the hazards associated with its improper use before
using this product.
4. Always refer to the vehicle owners or service manual
for location of proper lift and support points.
To lower load
!
Be sure that all tools and personnel are clear
before lowering load.
1. With suitable jack, raise vehicle clear of stands.
2. Carefully release support bar and allow extension
tube to glide down to lowest position.
3. Carefully remove stands, then carefully lower
vehicle with lift device.
3
MAINTENANCE
To help prevent rust, wipe clean and/or blow dry after each use. Do not apply oil or lubricant to ANY portion of this
product. Keep support bar in bar holder on base section.
If rust appears, sand affected area and cover with suitable utility paint. Please note that there is no replacement part
applicable to this device.
Storage
Store stands in upright position and in a clean, dry area.
REPLACEMENT PARTS
For product labels and owners manual, call or write: SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153,
U.S.A. Tel: (888) 332-6419 Fax: (816) 891-6599 E-Mail: [email protected] Website: http://www.omegalift.com
No other parts are available for this product. Jack stands must be replaced as a matched set and must never be used
singly or with another make or model stand.
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from date of purchase, SFA Companies will repair or replace, at its option,
without charge, any of its products, which fails due to a defect in material or workmanship under normal usage. This
limited warranty is a consumer's exclusive remedy.
Performance of any obligation under this warranty may be obtained by returning the warranted product, freight
prepaid, to SFA Companies Warranty Service Department, 10939 N. Pomona Ave., Kansas City, MO 64153.
Except where such limitations and exclusions are specifically prohibited by applicable law, (1) THE
CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE
PRODUCTS AS DESCRIBED ABOVE. (2) SFA Companies SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL
OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER. (3) ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO ONE YEAR, OTHERWISE THE REPAIR, REPLACEMENT OR REFUND AS
PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER,
AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. (4) ANY MODIFICATION,
ALTERATION, ABUSE, UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND
IS NOT COVERED BY THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not
apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights, which vary from state to state.
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
888-332-6419
[email protected]
4
">

Hello! I am an AI chatbot specifically trained to assist you with the 32105 32107, 32225 Jack Stands Operating Instructions & Parts Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

Supports partial vehicle loads
Adjustable height
Safety mechanisms
Durable construction
Rated capacity per pair
Supports up to 10 or 22 tons

Frequently asked questions

Pull up the extension tube and insert the tube support bar through the hole on the extension tube. Ensure that the support bar is secured before loading.

The rated capacity is per pair. Do not exceed the rated capacity.

Raise the vehicle clear of the stands using a suitable jack. Carefully release the support bar and allow the extension tube to glide down to the lowest position. Remove the stands and then carefully lower the vehicle with the lift device.

SFA Companies provides a one-year limited warranty on their jack stands, covering defects in materials or workmanship under normal usage.