User manual | Toshiba Personal Computer Satellite M70 /Satellite Pro M70

Add to my manuals
223 Pages

advertisement

User manual | Toshiba Personal Computer Satellite M70 /Satellite Pro M70 | Manualzz

Toshiba Personal Computer

Satellite M70 /Satellite Pro M70

Maintenance Manual

TOSHIBA CORPORATION

[CONFIDENTIAL]

Copyright

© 2004 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein.

Toshiba Personal Computer Satellite M70 /Satellite Pro M70 Maintenance Manual

First edition September 2004

Disclaimer

The information presented in this manual has been reviewed and validated for accuracy. The included set of instructions and descriptions are accurate for the A80/A85 Series at the time of this manual's production. However, succeeding computers and manuals are subject to change without notice.

Therefore, Toshiba assumes no liability for damages incurred directly or indirectly from errors, omissions, or discrepancies between any succeeding product and this manual.

Trademarks

IBM is a registered trademark, and OS/2 and PS/2 are trademarks of IBM Corporation.

Microsoft, MS-DOS, Windows, DirectSound and DirectMusic are registered trademarks of Microsoft

Corporation.

Intel and Pentium are registered trademarks, and SpeedStep is a trademark of Intel Corporation.

Sound Blaster is a registered trademark of Creative Technology Ltd.

Centronics is a registered trademark of Centronics Data Computer Corporation.

Photo CD is a trademark of Eastman Kodak.

All other properties are trademarks or registered trademarks of their respective holders.

ii

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Maintenance Manual

Preface

This maintenance manual describes how to perform hardware service maintenance for the Toshiba

Personal Computer Satellite SATELLITE M70 /SATELLITE PRO M70, referred to as the A80/A85

Series in this manual.

The procedures described in this manual are intended to help service technicians isolate faulty Field

Replaceable Units (FRUs) and replace them in the field.

SAFETY PRECAUTIONS

Four types of messages are used in this manual to bring important information to your attention. Each of these messages will be italicized and identified as shown below.

DANGER: “Danger” indicates the existence of a hazard that could result in death or serious bodily injury if the safety instruction is not observed.

WARNING: “Warning” indicates the existence of a hazard that could result in bodily injury if the safety instruction is not observed.

CAUTION: “Caution” indicates the existence of a hazard that could result in property damage if the safety instruction is not observed.

NOTE: “Note” contains general information that relates to your safe maintenance service.

Improper repair of the computer may result in safety hazards. Toshiba requires service technicians and authorized dealers or service providers to ensure the following safety precautions are adhered to strictly.

? Be sure to fasten screws securely with the right screwdriver. If a screw is not fully fastened, it could come loose, creating a danger of a short circuit, which could cause overheating, smoke or fire.

? If you replace the battery pack or RTC battery, be sure to use only the same model battery or an equivalent battery recommended by Toshiba. Installation of the wrong battery can cause the battery to explode.

Satellite M70 /Satellite Pro M70 Maintenance Manual iii

[CONFIDENTIAL]

The manual is divided into the following parts:

Chapter 1 Hardware Overview describes the A80/A85 Series system unit and each FRU.

Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems.

Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service.

Chapter 4 Replacement Procedures describes the removal and replacement of the FRUs.

Appendices The appendices describe the following:

? Handling the LCD module

? Board layout

? Pin assignments

? Keyboard scan/character codes

? Key layout

? Screw torque list

? Reliability

iv

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Maintenance Manual

Conventions

This manual uses the following formats to describe, identify, and highlight terms and operating procedures.

Acronyms

On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example:

Read Only Memory (ROM)

Keys

Keys are used in the text to describe many operations. The key top symbol as it appears on the keyboard is printed in boldface type.

Key operation

Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus (+) sign. For example, Ctrl + Pause (Break) means you must hold down Ctrl and at the same time press Pause (Break). If three keys are used, hold down the first two and at the same time press the third.

User input

Text that you are instructed to type in is shown in the boldface type below:

DISKCOPY A: B:

The display

Text generated by the computer that appears on its display is presented in the type face below:

Format complete

System transferred

Satellite M70 /Satellite Pro M70 Maintenance Manual v

[CONFIDENTIAL]

vi

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Maintenance Manual

Table of Contents

Chapter 1 Hardware Overview

1.1 Features ............................................................................................................................ 1-1

1.2 System Unit ....................................................................................................................... 1-5

1.3 2.5-inch Hard Disk Drive................................................................................................... 1-9

1.4 Removable Drives............................................................................................................ 1-10

1.5 Power Supply.................................................................................................................. 1-16

1.6 Batteries .......................................................................................................................... 1-18

Chapter 2 Troubleshooting Procedures

2.1 Troubleshooting Introduction.............................................................................................. 2-1

2.2 Troubleshooting Flowchart................................................................................................. 2-2

2.3 Power Supply Troubleshooting........................................................................................... 2-7

2.4 Display Troubleshooting................................................................................................... 2-12

2.5 Keyboard Troubleshooting............................................................................................... 2-15

2.6 External USB Devices Troubleshooting ............................................................................ 2-17

2.7 TV-Out Failure Troubleshooting....................................................................................... 2-19

2.8 Printer Port Troubleshooting............................................................................................. 2-21

2.9 TouchPad Troubleshooting............................................................................................... 2-23

2.10 Speaker Troubleshooting ................................................................................................. 2-25

2.11 Optical Drive Troubleshooting.......................................................................................... 2-27

2.12 Modem Troubleshooting .................................................................................................. 2-30

2.13 PCMCIA Troubleshooting............................................................................................... 2-32

2.14 IEEE 1394 Troubleshooting ............................................................................................. 2-34

2.15 Wireless LAN Troubleshooting ........................................................................................ 2-36

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Maintenance Manual vii

Chapter 3 Tests and Diagnostics

3.1 The Diagnostic Test............................................................................................................3-1

3.2 Executing the Diagnostic Test..............................................................................................3-2

3.3 Config Check Test .............................................................................................................3-6

3.4 DMI Check Test................................................................................................................3-7

3.5 PIO Loopback Test ...........................................................................................................3-8

3.6 IEEE 1394 Test .................................................................................................................3-9

3.7 Speaker Audio Test .........................................................................................................3-10

3.8 Fan ON/OFF Test ...........................................................................................................3-11

3.9 Main Battery Charge Test.................................................................................................3-12

3.10 FDD Test.........................................................................................................................3-13

3.11 CD-ROM Test ................................................................................................................3-14

3.12 Keyboard Test.................................................................................................................3-15

3.13 Mouse (Pad) Test ............................................................................................................3-17

3.14 LCD Pixels Mode Test.....................................................................................................3-19

3.15 Lid Switch Test ................................................................................................................3-20

3.16 HDD R/W Test................................................................................................................3-21

3.17 LAN Test ........................................................................................................................3-23

3.18 RTC Test.........................................................................................................................3-25

3.19 CD Control Button Test ...................................................................................................3-26

viii

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Maintenance Manual

Chapter 4 Replacement Procedures

4.1 General.............................................................................................................................. 4-1

4.2 Battery .............................................................................................................................. 4-7

4.3 PC Card............................................................................................................................ 4-9

4.4 HDD ............................................................................................................................... 4-11

4.5 Optical Drive Module ...................................................................................................... 4-13

4.6 Optical Drive ................................................................................................................... 4-15

4.7 Wireless LAN Unit .......................................................................................................... 4-17

4.8 Expansion Memory.......................................................................................................... 4-20

4.9 Keyboard........................................................................................................................ 4-23

4.10 Modem ........................................................................................................................... 4-26

4.11 Display Assembly ............................................................................................................ 4-28

4.12 Touch Cover ................................................................................................................... 4-31

4.13 Touch Pad....................................................................................................................... 4-34

4.14 Speakers ......................................................................................................................... 4-36

4.15 System Board.................................................................................................................. 4-37

4.16 Fan, Heat Sink, & CPU................................................................................................... 4-39

4.17 Display Mask .................................................................................................................. 4-42

4.18 LCD Module ................................................................................................................... 4-44

4.19 FL Inverter Board............................................................................................................ 4-47

Satellite M70 /Satellite Pro M70 Maintenance Manual ix

[CONFIDENTIAL]

Appendices

Appendix A Handling the LCD Module..................................................................................... A-1

Appendix B Board Layout ........................................................................................................ B-1

Appendix C Pin Assignments .................................................................................................... C-1

Appendix D Keyboard Scan/Character Codes.......................................................................... D-1

Appendix E Key Layout ............................................................................................................E-1

Appendix F Series Screw Torque List .......................................................................................F-1

Appendix G Reliability.............................................................................................................. G-1

x

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Maintenance Manual

Chapter 1

Hardware Overview

1

[CONFIDENTIAL]

1 Hardware Overview

1-ii

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

1 Hardware Overview

Chapter 1 Contents

1.1 Features ...................................................................................................................... 1-5

1.2 System Unit ............................................................................................................. 1-10

1.3 2.5-inch Hard Disk Drive ........................................................................................ 1-12

1.4 Optical device Drives .............................................................................................. 1-13

1.4.1 CD-RW & DVD-ROM ............................................................................. 1-13

1.4.2 DVD Super Multi drive supporting ±R Double Layer ............................. 1-14

1.5 Power Supply........................................................................................................... 1-15

1.6 Batteries ................................................................................................................... 1-17

1.6.1 Main Battery ............................................................................................. 1-18

1.6.2 RTC battery............................................................................................... 1-19

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

1-iii

1 Hardware Overview

Figures

Figure 1-1 2.5-inch HDD...............................................................................................1-12

Table

Table 1-1 2.5-inch SATA HDD specifications .............................................................1-12

Table 1-2 2.5-inch PATA HDD specifications .............................................................1-12

Table 1-3 DVD-ROM & CD-RW drive specifications ................................................1-13

Table 1-4 DVD Super Multi Double Layer drive specifications ..................................1-14

1-iv

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

1.1 Features

1 Hardware Overview

1.1 Features

The Satellite M70 Series Personal Computer uses extensive Large Scale Integration (LSI), and

Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight and high reliability. This computer incorporates the following features and benefits:

? CPU

?

Intel® Celeron® M Processor 350J/360J/370/380

?

Intel® Pentium® M Processor 725A/730/740/750/760/770/780

? Chipset

?

ATI Radeon® Xpress 200M +ATI IXP450

?

Mobile Intel® 915PM Express Chipset for external graphics controller

?

Mobile Intel® 915GM Express Chipset for integrated graphics controller

(Chipset depends on the model you purchased)

?

ATI Mobility® Radeon® X600SE

?

ATI Mobility® Radeon® X700

(GPU depends on the models you purchased)

?

ENE KB910 for Keyboard Controller, Battery management Unit, and RTC.

?

ENE CB1410 for PCMCIA controller

?

TI PCI7411 Multiple Digital Media Card Slot, IEEE 1394 and PCMCIA Controller

?

TI PCI4510, IEEE1394 and PCMCIA Controller

?

Realtek ALC250 for AC97 CODEC.

?

Realtek RTL8100CL for 10M/100M LAN

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

1-5

1 Hardware Overview

1.1 Features

? Memory

?

DDRII-533MHz specification compliant

?

Dual channel support

?

No On board memory

?

Two DDRII SODIMM with 256MB/512MB/1GB ,

?

Max. upgrade to 2GB with 2 DDRII SODIMM Socket

? BIOS

?

1MB Flash ROM for system BIOS.

?

Suspend to RAM/Disk.

?

Password protection (System).

?

Various hot key for system control.

?

Refreshable

?

Complete ACPI 1.0B Function

? Power

?

4-cell Lithium Ion smart battery pack with 14.4V*2000mAh

?

6-cell Lithium Ion smart battery pack with 10.8V*4000mAh

?

8-cell Lithium Ion smart battery pack with 14.4V*4300mAh

?

Approximately 12 hours or longer charging time to 100% battery capacity with system switched on.

?

Approximately 3 hours charge time to 100% battery capacity with system switched off.

?

Approximately 1.5 days discharging time in Standby Mode for the 8-cell battery, 1 day for the 6-cell battery and 0.75 days for 4-cell battery.

?

Discharge time in shutdown mode is approximately 1 month

? HDD

?

9.5mm, 2.5" HDD up to 120 GB

?

Bus Master IDE

?

9.5m/m, 2.5”HDD Support

?

Serial ATA and Parallel ATA

? Fixed Device Drivers

?

5.25” 12.7mm height CD-RW & DVD-ROM drive

?

5.25” 12.7mm height DVD Super Multi drive supporting ±R Double Layer

1-6

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

1.1 Features

1 Hardware Overview

? Optional Devices

?

256/512/1024MB SO-DIMM DDRII modules

?

Li-ION Battery Pack

?

AC adapter

?

USB FDD Kit

? Keyboard

The computer's keyboard layout is that of a 101/102-key enhanced keyboard.

There are four types of keys: typewriter keys, function keys, soft keys and cursor control keys. The typewriter keys are gray. The other keys are dark gray.

? TouchPad

This pointing control device, located in the center of the keyboard palm-rest, provides convenient control of the cursor without requiring desk space for a mouse. The TouchPad incorporates two mouse buttons.

? Display

?

15.4” TFT screen with a resolution of 1280 horizontal x 800 vertical pixels WXGA

150nits

?

15.4” TFT screen with a resolution of 1280 horizontal x 800 vertical pixels WXGA

150nits CSV

?

15.4” TFT screen with a resolution of 1280 horizontal x 800 vertical pixels WXGA

200nits

?

15.4” TFT screen with a resolution of 1280 horizontal x 800 vertical pixels WXGA

200nits CSV

? I/O Ports

?

USB (V2.0, horizontal type) x 3 (2 in rear side, 1 in left side )

?

RGB; One DDC2b compliant VGA port , 15pins (left side)

?

S-Video (left side)

?

Microphone jack (front side)

?

Headphone jack (front side)

?

VR volume control (front side)

?

Wireless Communication Switch and WLAN indicator (some models may not have this feature).

?

DC-In jack (rear side)

?

RJ-11 jack for 56Kbps V.92 Modem (rear side)

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

1-7

1 Hardware Overview

1.1 Features

?

RJ-45 jack with LED indicator (rear side)

?

Kensington lock (rear side)

?

IEEE 1394

?

5 in 1 Card reader (front side)

?

ExpressCard (some models may not have this feature).

?

PCMCIA with shutter door (Left side)

? PC Card Slot

?

One type II card socket

?

1.8" 10.5mm removable ATA Device

?

Card bus card or PC Care with hot insertion and removal

?

ACPI 1.1 Compliant.

?

Support 5V/3.3V PC Cards and 3.3V Cardbus cards.

?

Supports PCMCIA-ATA Specification.

? Express Card Slot

?

One Express Cardslot (some models may not have this feature).

? Multiple Digital Media Card Slot

?

Supports xD, SD, MS, MS Pro and MMC

? Communication

?

Modem: V90 (V.92)/56K bps specification compliant and 14.4K bps Send/Receive

Fax with MDC solution

?

V92/56K bps (US/Canada/UK/GR/FR)

?

V90/56K bps (other countries)

?

LAN: Realtek 8100CL (On Board 10/100Mbps) RTL8110SBL(BTO)

?

WOL from S3 on AC/Battery mode.

? Wireless LAN

?

802.11g: WLL3092-D4(MOW-LF) 54M 11/13CH (MB51L) (RoHS).

?

802.11a+g: Atheros WLL4071-D4(MOW) 54M 11/13CH (MB62HL) (RoHS)

?

Module integrated for Mini-PCI interface.

?

Easy service for WLAN.

?

Wireless communication killer switch (BTO)

?

Support MiniPCI IIIB

1-8

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

1.1 Features

1 Hardware Overview

?

Support Intel Wireless Coexistence system with Taiyo Yuden V2.0

? Universal Serial Bus (USB)

The computer has three Universal Serial Bus (USB) ports that comply with the USB 2.0 standard, which enable data transfer speeds more than 40 times faster than USB 1.1

(which this computer also supports.) The USB drives may be used to transfer data at Low,

Full, and high speeds.

? External monitor port

A 15-pin CRT port supporting DDC 2B enables connection of an external monitor, which is recognized automatically by Video Electronics Standards Association (VESA) Display

Data Channel (DDC) compatible functions.

? Sound system

Windows® Operating System compatible sound system provides internal speakers as well as jacks for an external microphone and headphone.

? TV-out (S-Video) port

Plug a 4-pin S-video cable into this connector for output of NTSC or PAL signal.

? LAN port

The computer comes with an RJ-45 Local Area Network (LAN) port. The LAN port provides connectivity for LAN.

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

1-9

1 Hardware Overview

1.2 System Unit

1.2 System Unit

The system unit is composed of the following major components:

? Processor

?

Intel® Celeron® M CPU up to 1.7GHZ 0.09u, 1M L2, FSB 400MHz

?

Intel® Pentium® M CPU up to 2.26GHZ 0.09u, 2M L2, FSB 533MHz

?

Micro FC-PGA package CPU

? System Logic

?

ATI Radeon® Xpress 200M +ATI IXP450

?

Mobile Intel® 915PM Express Chipset for external graphics controller

?

Mobile Intel® 915GM Express Chipset for integrated graphics controller

?

ATI Mobility® Radeon® X600SE

?

ATI Mobility® Radeon® X700

?

ENE KB910 for Keyboard Controller, Battery management Unit, and RTC.

?

ENE CB1410 for PCMCIA controller

?

TI PCI7411 Multiple Digital Media Card Slot, IEEE 1394 and PCMCIA Controller

?

TI PCI4510, IEEE1394 and PCMCIA Controller

?

Realtek ALC250 for AC97 CODEC.

?

Realtek RTL8100CL for 10M/100M LAN

? Keyboard Controller

?

ENE KB910 is use as Keyboard Controller and Battery management unit.

? Memory

?

DDRII-533MHz specification compliant

?

Dual channel support

?

No On board memory

?

Two DDRII SODIMM with 256MB/512MB/1GB ,

?

Max. upgrade to 2GB with 2 DDRII SODIMM Socket

1-10

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

1.2 System Unit

? Audio subsystem

?

Realtek 250D

?

Microphone- in and headphone-out.

?

No internal Microphone.

?

Two stereo speakers

?

Sound effect by SRS software

?

Volume control : Dial type

?

Supports Harman Speakers

?

Speaker Volume over 10cc

1 Hardware Overview

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

1-11

1 Hardware Overview

1.3 2.5-inch Hard Disk Drive

1.3 2.5-inch Hard Disk Drive

The internal HDD is a random access non-volatile storage device. It has a non-removable 2.5inch magnetic disk and mini-Winchester type magnetic heads. The computer supports hard drives up to 100 GB.

The HDD is shown in Figure 1-1. Specifications are listed in Table 1-1 and Table1-2.

Figure 1-1 2.5-inch HDD

Items 40GB 60GB 80GB 100GB

Formatted capacity (GB) 37.26 55.89 74.52 93.15

Logical Blocks (LBA) 78,125,000 117,187,500 156,301,488 195,371,568

Rotational speed (rpm) 5400

5400 5400 5400

Toshiba HDD Buffer (MB)

Hitachi HDD Buffer (MB)

16

8

16

8

16

8

16

8

Fujitsu HDD Buffer (MB)

Bytes per sector

8

512

8

512

8

512

8

512

Table 1-1 2.5-inch SATA HDD specifications

Items 40GB 60GB 80GB 100GB

Formatted capacity (GB) 37.26 55.89 74.52 93.15

Logical Blocks (LBA) 78,125,000 117,187,500 156,301,488 195,371,568

Rotational speed (rpm) 4,200/5400 4,200/5400 4200/5400 4200/5400

Toshiba HDD Buffer (MB)

Hitachi HDD Buffer (MB)

Fujitsu HDD Buffer (MB)

Bytes per sector

8/16

2/8

8/8

512

8/16

8/8

8/8

512

8/16

8/8

8/8

512

Table 1-2 2.5-inch PATA HDD specifications

8/16

8/8

8/8

512

1-12

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

1.4 Optical device Drives

1 Hardware Overview

1.4 Optical device Drives

?

DVD-ROM & CD-RW drive

?

DVD Super Multi drive supporting ±R Double Layer

1.4.1 CD-RW & DVD-ROM

The combo drive accepts 12-cm (4.72- inch) and 8-cm (3.15- inch) discs. At maximum, the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed and

CD-RW at 4x speed or High speed CD-RW at 10X or Ultra speed CD-RW at 24X speed.

The specifications of the DVD- ROM & CD-RW drive are listed in Table 1-3.

Item DVD-ROM mode CD-ROM mode

Data transfer rate (Mbytes/s)

33.3 (U-DMA transfer mode 2)

16.6 (PIO mode 4, Multiword DMA mode 2)

Access time (ms)

Average random access

180 150

Data buffer size (Mbytes) 2MB

Formats supported

DVD:

DVD-VIDEO, DVD-ROM, DVD-R (3.9G,4.7G), DVD-RW

(Ver.1.1), DVD-RAM, DVD+R, DVD+RW, DVD+R DL,

DVD-R DL.

CD:

CD-DA, CD-ROM Mode1, Mode2, , CD-R, CD-RW, CD-

ROMXA Mode2 (Form1, Form2), Photo CD (single/multisession), Enhanced CD (CD-EXTRA), CD-Text

Table 1-3 DVD-ROM & CD-RW drive specifications

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

1-13

1 Hardware Overview

1.4 Optical device Drives

1.4.2 DVD Super Multi drive supporting ±R Double Layer

The DVD Super Multi drive accepts 12-cm (4.72- inch) and 8-cm (3.15- inch) discs. At maximum, the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed and CD-RW at 4x speed or Ultra and High speed CD-RW at 10x speed and DVD-R at 8x speed and DVD-RW at 4x speed and DVD+R at 8x speed and DVD+RW at 4x speed and DVD-

RAM at 3x speed and DVD+R DL at 2.4x speed and DVD-R DL at 2x speed.

The specifications of the DVD Super Multi Double Layer drive are listed in Table 1-4

Item DVD-ROM mode CD-ROM mode

Data transfer rate (Mbytes/s)

33.3 (U-DMA transfer mode 2)

16.6 (PIO mode 4, Multiword DMA mode 2)

Access time (ms)

Average random access

180 150

Data buffer size (Mbytes) 2MB

Formats supported

DVD:

DVD-VIDEO, DVD-ROM, DVD-R (3.9G,4.7G), DVD-RW

(Ver.1.1), DVD-RAM, DVD+R, DVD+RW, DVD+R DL,

DVD-R DL

CD:

CD-DA, CD-ROM, CD-R, CD-RW, CD-ROMXA,

PhotoCD (muitiSession), Video CD, CD-Extra (CD+), CD-Text

Table 1-4 DVD Super Multi Double Layer drive specifications

1-14

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

1.5 Power Supply

1 Hardware Overview

1.5 Power Supply

This specification defines the performance and characteristic of 65W and 75W AC adapter power supply. It supplies a constant voltage 19V output source for M70 series notebook computer.

? A/D conversion

?

The EC uses 10-bit sampling for A/D conversion to determine the following values:

– Battery and temperature

? AC adaptor and battery check

?

The EC checks the following by A/D converted values:

– Battery installed

?

The EC checks the following by GPIO values:

– AC adaptor connected

? Abnormal check

?

The EC determines whether the condition is abnormal, and if so, stores an error code into the error register.

? Input port management

?

The EC monitors the following input signal status:

– System power ON/OFF status

– Direct CD power ON/OFF status

? Beep and LED control

?

Beep is caused by the low battery status.

?

The EC controls the following two kinds of LED

– DC IN LED (one color: green)

?

Green = indicates AC adaptor is connected

– Battery LED (two colors: orange and green)

?

Green solid = The battery is fully charged.

?

Orange = The computer is quick-charging the battery / The battery is low.

? Power ON/OFF sequence

?

When power is turned on or off, the EC starts the power on or off sequence.

– SQ0-4 = power ON sequence

– SQ5-B = power OFF sequence

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

1-15

1 Hardware Overview

1.5 Power Supply

? Battery charging control

?

The EC controls the following.

– The quick charging ON/OFF

– The detection of full charge

? Detection of the low battery

?

The EC detects the low battery point by the gas gauge.

– LB10M = The system will be driven by the battery for 12 more minutes.

– LB0 = The battery won't be able to drive the system after 3 minutes.

– LB1 = The battery can drive the system only during the suspend process.

– LB2 = The battery cannot drive the system.

? New battery installation

?

When a new battery is installed, the EC communicates with the E

2

PROM in the battery to read information of the newly installed battery.

? Battery capacity calculation

?

The EC reads battery remaining and percentage capacity from the battery through

SMBus.

1-16

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

1.6 Batteries

Battery name

Main battery

Main battery

Main battery

RTC battery

Material

Lithium-Ion

Lithium-Ion

Lithium-Ion

Lithium

1 Hardware Overview

1.6 Batteries

The computer has two types of battery:

? Main battery pack (18650 size)

? RTC battery

The removable main battery pack is the computer’s main power source when the AC adaptor is not attached.

The battery specifications are listed in the table below.

Output voltage

14.4V(8cell)

10.8V(6cell)

14.4V(4cell)

3.0 V

Capacity

4300mAH

4000mAH

2000mAH

15m AH

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

1-17

1 Hardware Overview

1.6 Batteries

1.6.1 Main Battery

Battery charging is controlled by a power supply microprocessor that is mounted on the system board. The power supply microprocessor controls whether the charge is on or off and detects a full charge when the AC adaptor and battery are attached to the computer. The system charges the battery using quick charge or trickle charge.

? Quick Battery Charge

When the AC adaptor is attached, there are two types of quick charge: quick charge when the system is powered off and normal charge when the system is powered on.

The times required for charges are listed in the table below.

Status

Normal charge (power on)

Quick charge (power off)

Charging time

12 hours or longer

About 4 hours

NOTES

1. The time required for normal charge is affected by the amount of power the system is consuming. Use of the fluorescent lamp and frequent disk access diverts power

and lengthens the charge time.

2. Using quick charge, the power supply microprocessor automatically stops the charge after eight hours regardless of the condition of the battery. Overcharging

could cause the battery to explode.

If any of the following occurs, the battery quick charge process stops.

1. The battery becomes fully charged.

2. The AC adaptor or battery is removed.

3. The battery or output voltage is abnormal.

4. The battery temperature is abnormal.

5. The battery SMBus communication fails.

6. The battery cell is bad.

? Detection of full charge

A full charge is detected from the battery pack through SMBus when the battery is charging.

1-18

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 S eries Maintenance Manual

1.6 Batteries

1 Hardware Overview

1.6.2 RTC battery

The RTC battery provides powe r to keep the current date, time and other setup information in memory while the computer is turned off. The table below lists the charging time and data preservation period of the RTC battery. The RTC battery is charged by the adaptor or main battery, while the computer is powered on.

Status

Charging Time (power on)

Data preservation period (full charge)

Time

About 24 hours

1 month

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

1-19

Chapter 2

Troubleshooting Procedures

2

2 Troubleshooting Procedures

Chapter 2 Contents

2.1 Troubleshooting Introduction.....................................................................................2-1

2.2 Troubleshooting Flowchart ........................................................................................2-2

2.3 Power Supply Troubleshooting..................................................................................2-7

2.4 Display Troubleshooting .............................................................................……….2-12

2.5 Keyboard Troubleshooting.......................................................................................2-15

2.6 External USB Devices Troubleshooting ..................................................................2-17

2.7 TV-Out Failure Troubleshooting .............................................................................2-19

2.8 TouchPad Troubleshooting ......................................................................................2-21

2.9 Speaker Troubleshooting..........................................................................................2-23

2.10 Optical drive troubleshooting ..................................................................................2-27

2.11 Modem Troubleshooting ..........................................................................................2-30

2.12 PCMCIA Troubleshooting .......................................................................................2-32

2.13 IEEE 1394 Troubleshooting.....................................................................................2-34

2.14 Wireless LAN Troubleshooting ...............................................................................2-36

2.15 Express card troubleshooting ....................................................................................2-38

2.16 Bluetooth Troubleshooting………………………………………………….………2-40

2-ii

[CONFIDENTIAL]

2 Series Maintenance Manual

2 Troubleshooting Procedures

Figures

Figure 2-1 Troubleshooting flowchart (1/2) .................................................................... 2-3

Figure 2-1 Troubleshooting flowchart (2/2) .................................................................... 2-4

Figure 2-2 Power Supply Troubleshooting Process ........................................................ 2-7

Figure 2-3 Display troubleshooting process .................................................................. 2-12

Figure 2-4 Keyboard troubleshooting process .............................................................. 2-15

Figure 2-5 External USB device troubleshooting process ............................................ 2-17

Figure 2-6 TV-out troubleshooting process .................................................................. 2-19

Figure 2-7 TouchPad troubleshooting process .............................................................. 2-21

Figure 2-8 Speaker troubleshooting process ................................................................. 2-23

Figure 2-9 Optical drive troubleshooting process ......................................................... 2-27

Figure 2-10 Modem troubleshooting process .................................................................. 2-30

Figure 2-11 PCMCIA troubleshooting process ............................................................... 2-32

Figure 2-12 IEEE 1394 troubleshooting process............................................................. 2-34

Figure 2-13 Wireless LAN troubleshooting process ....................................................... 2-36

Figure 2-14 Express card troubleshooting process.......................................................... 2-38

Figure 2-15 Bluetooth troubleshooting…………………………………………….……2-40

Tables

Table 2-1 Battery LED ...................................................................................................... 2-8

Table 2-2 DC-IN LED ...................................................................................................... 2-9

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

2-iii

2.1 Troubleshooting Introduction

2 Troubleshooting Procedures

2.1 Troubleshooting Introduction

Chapter 2 describes how to determine if a Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are:

1. Display

2. USB Floppy Drive

6. TouchPad

7. Speaker

11. IEEE 1394 port

12. Wireless LAN system

3. Keyboard

4. USB ports

5. TV-out port

8. Optical drive

9. Modem

10. PCMCIA unit

13. Express card unit.

14. Bluetooth

The Diagnostics Disk operations are described in Chapter 3. Detailed replacement procedures are given in Chapter 4.

The following tools are necessary for implementing the troubleshooting procedures:

1. Diagnostics Disk (Repair and Sound Repair)

2. Phillips screwdriver (2 mm)

3. 6mm nut driver (for the helix screw nuts on the rear ports for CPU door)

4. 2DD or 2HD formatted work disk for floppy disk drive testing

5. Sycard (PCMCIA test card)

6. Cleaning kit for floppy disk drive troubleshooting

7. Cleaning kit for optical drive troubleshooting

8. Multimeter

9. External monitor

10. USB compatible keyboard

11. Multimedia sound system with line- in and line-out ports

12. Headphones

13. USB test module and USB cable

14. Music CD

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

2-1

2 Troubleshooting Procedures

2.2 Troubleshooting Flowchart

2.2 Troubleshooting Flowchart

If you know the location of the malfunction, turn directly to the appropriate section of this chapter. If the problem is unspecified, use the flowchart in Figure 2-1 as a guide for determining which troubleshooting procedures to execute. Before performing any troubleshooting procedures, verify the following:

? Ask the user if a password is registered and, if it is, ask him or her to enter the password.

? Verify with the customer that Toshiba Windows XP is installed on the hard disk. Operating systems that were not preinstalled by Toshib a can cause the computer to malfunction.

? Make sure all optional equipment is removed from the computer.

? Make sure the floppy disk drive, if installed, is empty. If no FDD module is installed, you should use an external FDD to run the diagnostics tests

2-2

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures

S T A R T

C o n n e c t t h e A C a d a p t e r t o t h e D C - I N s o c k e t

I s t h e D C - I N L E D o n ?

Y e s

I s t h e B a t t e r y L E D o n ?

Y e s

T u r n t h e P o w e r s w i t c h o n

Y e s

I s t h e P o w e r O n L E D o n ?

Y e s

I s t h e " T o s h i b a " l o g o m e s s a g e d i s p l a y ?

Y e s

I f t h e " p a s s w o r d " m e s s a g e d i s p l a y s , t y p e t h e p a s s w o r d , t h e n p r e s s E n t e r .

No

No

No

No

P e r f o r m t h e P o w e r S u p p l y

T r o u b l e s h o o t i n g p r o c e d u r e s i n s e c t i o n 2 . 3

P e r f o r m t h e P o w e r S u p p l y

T r o u b l e s h o o t i n g p r o c e d u r e s i n s e c t i o n 2 . 3

P e r f o r m t h e P o w e r S u p p l y

T r o u b l e s h o o t i n g p r o c e d u r e s i n s e c t i o n 2 . 3

P e r f o r m t h e D i s p l a y

T r o u b l e s h o o t i n g p r o c e d u r e s i n s e c t i o n 2 . 4

I s T o s h i b a W i n d o w s b e i n g l o a d e d ?

Y e s

A

No

P e r f o r m d i a g n o s t i c s p r o g r a m .

R u n C M 1 6 5 . E X E a n d s e l e c t t h e

H A R D D I S K i t e m .

Figure 2-1 Troubleshooting flowchart (1/2)

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

2-3

2 Troubleshooting Procedures

A

2.2 Troubleshooting Flowchart

Does typed characters appear correctly?

Yes

Insert the diagnostics disk into the FDD.

Then run the diagnostics test program.

Yes

Is the diagnostics test loaded?

Yes

Allow each test to perform automatically

No

Perform the Keyboard

Troubleshooting procedures in section 2.6

No

Perform the FDD

Troubleshooting procedures in section 2.5

Is an error detected by any of the diagnostics tests?

No

System is normal

Yes

After confirming which diagnostics test has detected an error, perform the appropriate procedure as outlined below.

End

Figure 2-1 Troubleshooting flowchart (2/2)

2-4

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures

If the diagnostics program cannot detect an error, the problem may be intermittent. The test program should be executed several times to isolate the problem. When a problem has been located, perform the appropriate troubleshooting procedures as follows:

1. If an error is detected by the battery test, perform the Power Supply Troubleshooting procedures in Section 2.3.

2. If an error is detected by the display test, perform the Display Troubleshooting procedures in Section 2.4.

3. If an error is detected by the keyboard test, perform the Keyboard Troubleshooting procedures in Section 2.5.

4. If an error is detected by the TouchPad test, perform the TouchPad Troubleshooting procedures in Section 2.8.

5. If an error is detected by the audio test, perform the Speaker Troubleshooting procedures in Section 2.9 and the Optical Drive Troubleshooting Procedures in Section 2.9.

6. If an error is detected by the modem test, perform the Modem Troubleshooting

Procedures in Section 2.10.

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

2-5

2 Troubleshooting Procedures

2.2 Troubleshooting Flowchart

Other problems that are not covered by the diagnostics program may be discovered by a user.

1. If an error is detected when using an external USB device, perform the External USB

Devices Troubleshooting procedures in Section 2.6.

2. If an error is detected when using the TV-out connection, perform the TV-Out Failure

Troubleshooting procedures in Section 2.7.

3. If an error is detected when using the speakers, perform the Speaker Troubleshooting procedures in Section 2.10.

4. If an error is detected when using the modem, perform the Modem Troubleshooting procedures in Section 2.12.

5. If an error is detected when using the PCMCIA unit, perform the PCMCIA

Troubleshooting procedures in Section 2.13.

6. If an error is detected when using the IEEE1394 device, perform the IEEE1394 device

Troubleshooting procedures in Section 2.14.

7. If an error is detected when using the Wireless LAN, perform the Wireless LAN

Troubleshooting procedures in Section 2.15.

2-6

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.3 Power Supply Troubleshooting

2.3 Power Supply Troubleshooting

S TAR T

Check Power Supply Status

(Procedure 1)

2 Troubleshooting Procedures

Are the DC-IN and

Battery LEDs lit?

Yes

Check power supply connections

(Procedure 3)

No

Replace adaptor / battery

(Procedure 2)

Can you turn the computer on?

No

Are the internal power connections secure?

Yes

Replace system board

Yes

Run diagnostic program

(Procedure 4)

No

Perform internal connection check

(Procedure 5)

E N D

Figure 2-2 Power Supply Troubleshooting Process

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

2-7

2 Troubleshooting Procedures

2.2 Troubleshooting Flowchart

The power supply controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed.

The flowchart in Figure 2-2 gives a summary of the process. The procedures described in this section are:

Procedure 1: Power status check

Procedure 2: Adaptor / battery replacement

Procedure 3: Power supply connection check

Procedure 4: Diagnostic check

Procedure 5: Internal connection check

Procedure 1 Power Status Check

The following LEDS indicate the power supply status:

Battery LED

DC-IN LED

The power supply controller displays the power supply status through the Battery and the DC-IN

LEDS as listed in the tables below.

Table 2-1 Battery LED

Battery State LED colors

Charging Amber, solid on

Discharging

Definition

Battery charging with AC .

Green, solid on

Green color off

Battery fully charged by AC

Battery abnormal stop charging with AC

(Bad cell/ Overheated)

Amber, blinking Battery within low state: 12 minutes

(LED on for 1 second remaining every 4 seconds)

Amber, blinking Battery within critical low state: 3

(LED on for 1 second minutes remaining. The system is every 2 seconds) protected and cannot be re-powered on without the AC power connected.

Amber color off Battery not in low or critical low state;

It’s in discharging state

2-8

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures

Table 2-2 DC-IN LED

AC-IN LED Power supply status

Solid on AC power exists (LED is solid green).

Off No AC power exists.

To check the power supply status, install a battery pack and connect an AC adaptor to the DC-IN port on the computer and to a power supply.

If the DC-IN LED or Battery LED is not lit, go to Procedure 2.

Procedure 2 Adaptor / battery replacement

A faulty adaptor may not supply power or may not charge the battery. Perform Check 1.

Check 1 Connect a new AC adaptor. If the problem is not resolved, go to Check 2.

Check 2 Insert a new battery. If the problem is still not resolved, go to Procedure 3.

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

2-9

2 Troubleshooting Procedures

Procedure 3 Power supply connection check

The power supply wiring diagram is shown below:

AC adaptor cord

AC power cord

AC adaptor

System board

Battery

2.2 Troubleshooting Flowchart

Any of the connectors may be disconnected. Perform Check 1.

Check 1 Disconnect the AC power cord from wall outlet. Check the power cable for breaks. If the power cord is damaged, connect a new AC power cord. If there is no damage, go to Check 2.

Check 2 Make sure the AC adaptor cord and AC power cord are firmly plugged into the DC-

IN socket, AC adaptor inlet and wall outlet. If these cables are connected correctly, go to Check 3.

Check 3 Make sure that the DC-IN input port socket is firmly secured to the system board of the computer.

?

If the DC-IN input socket is loose, go to Procedure 5.

?

If it is not loose, go to Check 4.

Check 4 Use a multi- meter to make sure that the AC adaptor output voltage is close to 19 V.

If the output is several percent lower than 19 V, go to Check 5. If the output is close to 19 V, go to Check 6.

Check 5 Connect a new AC adaptor or AC power cord.

?

If the DC-IN LED does not light, go to Procedure 4.

?

If the battery LED does not light, go to Check 6.

Check 6 Make sure the battery pack is installed in the computer correctly. If the battery is properly installed and the battery LED still does not light, go to Procedure 4.

2-10

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures

Procedure 4 Diagnostic check

The power supply may not charge the battery pack. Perform the following procedures:

1. Reinstall the battery pack.

2. Attach the AC adaptor and turn on the power. If you cannot turn on the power, go to

Procedure 5.

3. Run the Diagnostic test following the procedures described in Chapter 3, Tests and

Diagnostics. If no problem is detected, the battery is functioning normally.

Procedure 5 Replacement check

The system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures. Check the connection between the AC adaptor and the system board. After checking the connection, perform Check 1:

Check 1 Use a multi- meter to make sure that the fuses on the system board are not blown. If a fuse is not blown, go to Check 2. If a fuse is blown, go to Check 3.

Check 2 Make sure that the battery cable is firmly connected to the system board. If it is connected firmly, go to Check 3.

Check 3 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4.

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

2-11

2 Troubleshooting Procedures

2.4 Display Troubleshooting

S T A R T

P e r f o r m e x t e r n a l d i s p l a y c h e c k

( P r o c e d u r e 1 )

2.4 Display Troubleshooting

Y e s

D o e s t h e e x t e r n a l d i s p l a y f u n c t i o n o k ?

N o

P e r f o r m d i a g n o s t i c c h e c k

( P r o c e d u r e 2 )

W a s a d i s p l a y p r o b l e m d e t e c t e d ?

Y e s

P e r f o r m c o n n e c t o r a n d r e p l a c e m e n t c h e c k

( P r o c e d u r e 3 )

R e p l a c e s y s t e m b o a r d

N o

D i s p l a y i s n o t f a u l t y . C o n t i n u e t r o u b l e s h o o t i n g r e f e r t o F i g u r e 2 . 1

E N D

Figure 2-3 Display troubleshooting process

2-12

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.4 Display Troubleshooting 2 Troubleshooting Procedures

This section describes how to determine if the computer’s display is functioning properly. The process is out lined in Figure 2-3. Start with Procedure 1 and continue with the other procedures as instructed.

Procedure 1: External display check

Procedure 2: Diagnostic check

Procedure 3: Connector and replacement check

Procedure 1 External display check

Connect an external display to the computer’s external monitor port, then boot the computer.

The computer automatically detects the external display.

If the external display works correctly, the internal LCD may be damaged. Go to Procedure 3.

If the external monitor appears to have the same problem as the internal monitor, the system board may be damaged. Go to Procedure 2.

Procedure 2 Diagnostic check

The Display Test program is stored on the computer’s Diagnostics disk. This program checks the display controller on the system board. Insert the Diagnostics disk in the computer’s floppy disk drive, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics for details.

If an error is detected, go to Procedure 3. If an error is not detected, the display is functioning properly.

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

2-13

2 Troubleshooting Procedures

2.4 Display Troubleshooting

Procedure 3 Connector and replacement check

The FL inverter board, LCD module, and system board are connected to the display circuits.

Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks:

Check 1 Make sure the DDR RAM module is seated properly. Test display again. If the problem still exits, replace the DDR RAM module. If the problem still exists, perform Check 2.

Check 2 Replace the FL inverter board with a new one and test display again. If the problem still exists, perform Check 3.

Check 3 Replace the LCD module with a new one and test display again. If the problem still exists, perform Check 4.

Check 4 Replace the LCD/FL cable with a new one and test display again. If the problem still exists, perform Check 5.

Check 5 Replace the CPU with another of the same specifications. If the problem still exists, perform Check 6.

Check 6 The system board may be damaged. Replace it with a new one.

2-14

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.5 Keyboard Troubleshooting

2.5 Keyboard Troubleshooting

S T A R T

P e r f o r m e x t e r n a l k e y b o a r d c h e c k

( P r o c e d u r e 1 )

2 Troubleshooting Procedures

N o

D o e s t h e e x t e r n a l k e y b o a r d f u n c t i o n o k ?

Y e s

P e r f o r m d i a g n o s t i c c h e c k

( P r o c e d u r e 2 )

W a s a k e y b o a r d p r o b l e m d e t e c t e d ?

Y e s

P e r f o r m c o n n e c t o r a n d r e p l a c e m e n t c h e c k

( P r o c e d u r e 3 )

R e p l a c e s y s t e m b o a r d

N o

K e y b o a r d i s n o t f a u l t y . C o n t i n u e t r o u b l e s h o o t i n g r e f e r t o F i g u r e 2 . 1

E N D

Figure 2-4 Keyboard troubleshooting process

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

2-15

2 Troubleshooting Procedures

2.5 Keyboard Troubleshooting

To determine if the computer’s keyboard is functioning properly, perform the following procedures. Figure 2-5 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.

Procedure 1: External keyboard check

Procedure 2: Diagnostic check

Procedure 3: Connector and replacement check

Procedure 1 External keyboard check

Connect a USB keyboard to one of the computer’s USB ports, then boot the computer. The computer automatically detects the external keyboard.

If the external keyboard works correctly, the internal keyboard or its connections may be faulty.

Go to Procedure 2.

If the external keyboard appears to have the same problem as the internal keyboard, the system board may be damaged. Replace it with a new one following the instructions in Chapter 4.

Procedure 2 Diagnostic check

Run the Diagnostic Program, which will automatically execute the Keyboard Test. Refer to

Chapter 3, Tests and Diagnostics for more information on how to run the program.

If an error is located, go to Procedure 3. If an error does not occur, the keyboard is functioning properly.

Procedure 3 Connector and replacement check

The keyboard and/or system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks.

Check 1 Make sure the keyboard cable is firmly connected to the system board.

If the connection is loose, reconnect firmly and repeat Procedure 2. If there is still an error, go to Check 2.

Check 2 The keyboard may be damaged. Replace it with a new one following the instructions in Chapter 4.

If the problem still exists, perform Check 3.

Check 3 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4.

2-16

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.6 External USB Devices Troubleshooting

2.6 External USB Devices Troubleshooting

2 Troubleshooting Procedures

S T A R T

P e r f o r m e x t e r n a l d e v i c e a n d c o n n e c t i o n c h e c k

( P r o c e d u r e 1 )

C h e c k U S B p o r t c o n n e c t i o n

Y e s

D o e s t h e d e v i c e f u n c t i o n w h e n c o n n e c t e d t o a d i f f e r e n t U S B p o r t ?

N o

D o e s a n a l t e r n a t i v e U S B d e v i c e f u n c t i o n c o r r e c t l y ?

Y e s

O r i g i n a l U S B d e v i c e i s f a u l t y

N o

R e p l a c e s y s t e m b o a r d

( P r o c e d u r e 2 )

E N D

Figure 2-5 External USB device troubleshooting process

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

2-17

2.6 External USB Devices Troubleshooting 2 Troubleshooting Procedures

To determine if the computer’s external USB devices are functioning properly, perform the following procedures. Figure 2-6 outlines the process. Start with Procedure 1 and continue as instructed.

Procedure 1: External device and connection check

Procedure 2: Replace system board

Procedure 1 External device and connection check

The USB device may be damaged or the connection may be faulty. Perform Check 1.

Check 1 Make sure USB device cable is firmly plugged into one of the USB sockets. If the cable is connected correctly, go to Check 2.

Check 2 Plug the USB device into another USB socket (there are three in all). If the USB device still does not work, go to Check 4.

If the device functions correctly when connected to another USB port, go to Check 3.

Check 3 Make sure that the USB socket is firmly secured to the system board of the computer.

If the malfunction remains, the system board may be damaged. Go to Procedure 2.

Check 4 Connect an alternative USB device to one of the computer’s USB ports, and then boot the computer. The computer automatically detects the external device.

If the alternative USB device works correctly, the original device may be damaged and should be replaced.

If the alternative USB device appears to have the same problem as the original device, the system board may be damaged. Go to Procedure 2.

Procedure 2 Replace system board

If the error persists, the system board may be damaged. Replace it with a new one following the instructions in Chapter 4.

2-18

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.7 TV-Out Failure Troubleshooting

2.7 TV-Out Failure Troubleshooting

S T A R T

P e r f o r m T V c o n n e c t i o n c h e c k

( P r o c e d u r e 1 )

2 Troubleshooting Procedures

D o e s r e p l a c e m e n t T V c a b l e f u n c t i o n p r o p e r l y ?

N o

P e r f o r m T V s e t c h e c k

( P r o c e d u r e 2 )

N o R e p l a c e T V c a b l e

T V f u n c t i o n i n g o k ?

Y e s

R e p l a c e s y s t e m b o a r d

E N D

No

U s e d i f f e r e n t T V s e t

Figure 2-6 TV-out troubleshooting process

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

2-19

2 Troubleshooting Procedures 2.7 TV-Out Failure Troubleshooting

To determine if the computer’s TV-out port is functioning properly, perform the following procedures. Figure 2-7 outlines the process. Start with Procedure 1 and continue as instructed.

Procedure 1: TV connection check

Procedure 2: TV set check

Procedure 1 TV connection check

The TV cable may be damaged or the connections may be loose. Perform Check 1:

Check 1 Make sure TV cable is firmly plugged into both the TV set and the TV-out port of the computer. If the cable is connected correctly, go to Check 2.

Check 2 Make sure the TV-out port is firmly secured to the system board of the computer. If the malfunction remains, go to Check 3.

Check 3 The TV cable may be damaged. Replace with a good cable. If the malfunction remains, go to Procedure 2.

Procedure 2 TV set check

The TV set may be faulty. Perform Check 1:

Check 1 Try using the set for television reception. If it does not work, the set may be damaged. If the set does work, perform Check 2.

Check 2 Try connecting a different television to the computer. If the replacement television works, the original set may be damaged. If the replacement set does not work the system board may be damaged. Replace it with a new one following the instructions in Chapter 4.

2-20

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.8 Touch Pad Troubleshooting

2.8 TouchPad Troubleshooting

START

TouchPad connection check (Procedure 1)

2 Troubleshooting Procedures

TouchPad replacement check (Procedure 2)

Replace system board

END

Figure 2-7 TouchPad troubleshooting process

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

2-21

2 Troubleshooting Procedures

2.8 TouchPad Troubleshooting

To determine if the computer’s built- in TouchPad is functioning properly, perform the following procedures. Figure 2-9 outlines the process. Start with Procedure 1 and continue as instructed.

Procedure 1: TouchPad connection check

Procedure 2: TouchPad replacement check

Procedure 1 TouchPad connection check

The TouchPad is connected via the TouchPad FPC to the system board. Make sure the TouchPad

FPC cable is firmly connected to the TouchPad and system board. Refer to Chapter 4,

Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks.

If any of the connections are loose, reconnect firmly. If any of the connections is damaged, or there is still an error, go to Procedure 2.

Procedure 2 TouchPad replacement check

The TouchPad unit or FPC may be defective or damaged. Replace each with a new one following the steps in Chapter 4. If the FDD is still not functioning properly, replace the system board with a new one following the steps in Chapter 4.

2-22

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.9 Speaker Troubleshooting

2.9 Speaker Troubleshooting

START

Perform audio source test

(Procedure 1)

2 Troubleshooting Procedures

Do all sources have same problem?

Yes

Perform earphone test

(Procedure 2)

No

Speakers are not faulty. Continue troubleshooting see Figure 2-1

Do earphones function correctly?

Yes

No

Perform connection check

(Procedure 3)

Perform replacement check

(Procedure 4)

Replace system board

END

Figure 2-8 Speaker troubleshooting process

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

2-23

2 Troubleshooting Procedures

2.9 Speaker Troubleshooting

To determine if the computer’s built- in speakers are functioning properly, perform the following procedures. Figure 2-10 outlines the process. First adjust the speaker volume to an appropriate level. Start with Procedure 1 and continue as instructed.

Procedure 1: Audio source test

Procedure 2: Earphone test

Procedure 3: Connection check

Procedure 4: Replacement check

Procedure 1 Audio source test

Try different audio sources (e.g. an audio CD and digital music file) to determine whether the fault is in the speaker system or not. If not all sources have sound problem, the problem is in the source devices. If all have the same problem, continue with Procedure 2.

Procedure 2 Earphone test

Connect a set if earphones or external speakers. If these function correctly, go to Procedure 3. If they do not function correctly, the system board may be defective or damaged. Replace it with a new one.

Procedure 3 Connection check

Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and make sure the speaker cable is firmly connected to the audio board. If the stereo speakers are still not functioning properly, go to Procedure 4.

Procedure 4 Replacement check

If the stereo speakers don't sound properly, the stereo speakers may be defective or damaged.

Replace them with new ones. If the stereo speakers still do not work properly, try replacing in turn the audio board and system board.

2-24

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.10 Optical Drive Troubleshooting

2.10 Optical Drive Troubleshooting

START

Perform audio CD check

(Procedure 1)

2 Troubleshooting Procedures

Audio CD functions ok?

No

Perform drivecleaning check

(Procedure 2)

Yes

Perform software check

(Procedure 3)

Perform diagnostic test

(Procedure 4)

Perform connection and replacement check

(Procedure 5)

Replace system board

END

Figure 2-9 Optical drive troubleshooting process

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

2-

27

2 Troubleshooting Procedures

2.10 Optical Drive Troubleshooting

This section describes how to determine if the computer’s internal optical drive is functioning properly. The Satellite M70 module bays can accommodate the following optical drives:

?

DVD SuperMulti supporting +-R Double Rayer

?

COMBO device

Figure 2-11 outlines the process. Perform the steps below starting with Procedure 1 and continue with the other procedures as required.

Procedure 1: Audio CD test

Procedure 2: Drive cleaning check

Procedure 3: Software check

Procedure 4: Diagnostic test

Procedure 5: Connection and replacement check

Procedure 1 Audio CD check

First, insert an audio CD into the CD/DVD drive. If it works, the problem is not with the drive.

Go to Procedure 3. If the audio CD does not work, go to Procedure 2. If the CD/DVD LED on the front panel does not light when the disc is played and the drive gives no response, go straight to Procedure 3.

Procedure 2 Drive cleaning check

Insert a CD/DVD drive-cleaning disk into the drive clean according to the drive-cleaning product instructions. If the problem persists, go to Procedure 3.

Procedure 3 Software check

Ensure that the appropriate driver has been installed on the computer for the CD/DVD drive.

Procedure 4 Diagnostic test

The audio test program stored in the Diagnostics Disk will test the drive’s ability to play an audio

CD. See Chapter 3 for details.

If any errors occur while executing the diagnostic program, go to Procedure 5.

2-28

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.10 Optical Drive Troubleshooting 2 Troubleshooting Procedures

Procedure 5 Connection check and replacement check

The optical drive connects to the system board. The drive may be disconnected, or the drive or system board may be damaged. Disassemble the computer following the steps described in

Chapter 4, Replacement Procedures, and perform the following checks:

Check 1 Make sure the drive is firmly connected to the system board. If the connection is good and there is still an error, go to Check 2.

Check 2 The drive or drive cable may be defective or damaged. Replace each with a new one following the steps in Chapter 4, Replacement Procedures. If the drive is still not functioning properly, perform Check 3.

Check 3 The system board may be damaged. Replace it with new one following the instructions in Chapter 4, Replacement Procedures.

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

2-

29

2 Troubleshooting Procedures

2.11 Modem Troubleshooting

START

Perform telephone line connection check

(Procedure 1)

2.11 Modem Troubleshooting

Computer unable to detect telephone signal?

Yes

Check / replace telephone line and connections

No

Perform connection check

(Procedure 2)

Perform replacement check

(Procedure 3)

Replace system board

END

Figure 2-10 Modem troubleshooting process

2-30

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.11 Modem Troubleshooting 2 Troubleshooting Procedures

This section describes how to determine if the computer's modem is functioning properly. Figure

2-12 outlines the process. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required.

Procedure 1: Telephone line connection check

Procedure 2: Modem card connection check

Procedure 3: Modem card replacement check

Procedure 1 Telephone line connection check

The telepho ne cable may be damaged or the connections may be loose. Attempt to connect the computer to a network through using the modem. If the modem does not function at all, go to

Procedure 3. If the attempt fails because the computer detects no telephone signal, the fault may be in the telephone cable, the wall socket or the modem port. Perform Check 1:

Check 1 Make sure telephone cable is firmly plugged into both the telephone wall socket and the modem port of the computer. If the cable is connected correctly, go to Check 2.

Check 2 Make sure the modem port is firmly secured to the system board of the computer. If the malfunction remains, go to Check 3.

Check 3 The telephone cable may be damaged. Replace with a good cable. If the malfunction remains, go to Procedure 2.

Procedure 2 Modem card connection check

Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and ensure that the modem card is well connected to the system board. If the problem persists, perform Procedure 3.

Procedure 3 Modem replacement check

The modem card or RJ-11 jack may be faulty. Try replacing them. If the problem persists, the system board may be defective or damaged. Replace the System Board with a new one following the steps in Chapter 4, Replacement Procedures.

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

2-

31

2 Troubleshooting Procedures

2.12 PCMCIA Troubleshooting

START

Perform SYCARD test

(Procedure 1)

2.12 PCMCIA Troubleshooting

Do errors occur during

SYCARD test?

No

PCMCIA unit is not faulty.

Yes

Perform PCMCIA socket replacement check

(Procedure 2)

Replace system board

END

Figure 2-11 PCMCIA troubleshooting process

2-32

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.12 PCMCIA Troubleshooting 2 Troubleshooting Procedures

This section describes how to determine if the PCMCIA card player is functioning properly. The process is summarized in Figure 2-13. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required.

Procedure 1: Sycard test

Procedure 2: PCMCIA socket replacement check

Procedure 1 SYCARD test

The SYCARD test card contains a PCMCIA test program. Ensure the card in fully inserted into the socket before running the program.

If an error occurs during the SYCARD test, perform Procedure 2. If no error occurs, it is likely that the original PC card was faulty.

Procedure 2 PCMCIA socket replacement check

The PCMCIA socket may be damaged or defective, for instance the socket pins can be bent.

Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and replace the socket. If the problem persists, the system board may be defective or dama ged.

Replace the system board with a new one following the steps in Chapter 4.

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

2-

33

2 Troubleshooting Procedures

2.13 IEEE 1394 Troubleshooting

START

Perform IEEE 1394 device check

(Procedure 1)

2.13 IEEE 1394 Troubleshooting

N o

Is IEEE 1394 transmission ok?

Yes

Perform diagnostic check

(Procedure 2)

Was an IEEE 1394 problem detected?

Yes

Perform connection and replacement check

(Procedure 3)

No

IEEE 1394 port and transmission are not faulty. Continue troubleshooting - refer to Figure 2.1

Replace system board

2-34

END

Figure 2-12 IEEE 1394 troubleshooting process

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.13 IEEE 1394 Troubleshooting 2 Troubleshooting Procedures

To determine if the computer’s IEEE 1394 system is functioning properly, perform the following procedures. Figure 2-14 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.

Procedure 1: IEEE 1394 device check

Procedure 2: Diagnostic check

Procedure 3: Connection and replacement check

Procedure 1 IEEE 1394 device check

Connect an IEEE 1394 device to the computer’s IEEE 1394 port, then boot the computer for

Windows XP. The computer should automatically detect the 1394 device. Check whether the device can transmit data to the computer.

If the device is able to communicate with the computer, the problem may be intermittent or connections may be faulty. Go to Procedure 2.

If communication is impaired, there may be a faulty connection. Go to Procedure 3.

Procedure 2 Diagnostic check

Run the Diagnostic Program, which will automatically execute the IEEE 1394 port test for transmission. Refer to Chapter 3, Tests and Diagnostics for more information on how to run the program.

If an error is located, go to Procedure 3. If an error does not occur, the 1394 port is functioning properly.

Procedure 3 Connection and replacement check

The transmission cable may be damaged or the connections may be loose. Perform Check 1:

Check 1 Make sure the transmission cable is firmly plugged into both the IEEE 1394compatible device and the IEEE 1394 port of the computer. If the cable is connected correctly, go to Check 2.

Check 2 Make sure the IEEE 1394 port is firmly secured to the system board of the computer.

If the malfunction persists, go to Check 3.

Check 3 The transmission cable may be damaged. Replace with a good cable. If the malfunction persists, go to Check 4

Check 4 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4.

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

2-

35

2 Troubleshooting Procedures

2.14 Wireless LAN Troubleshooting

START

2.14 Wireless LAN Troubleshooting

Perform diagnostic test

(Procedure 1)

Was a wireless LAN problem delected?

Yes

Perform connector and replacement check

(Procedure 2)

No

Wireless LAN system is not faulty. Continue troubleshooting - refer to Figure 2.1

Replace wireless LAN antenna/unit

Replace system board

2-36

END

Figure 2-13 Wireless LAN troubleshooting process

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.14 Wireless LAN Troubleshooting 2 Troubleshooting Procedures

The wireless LAN antenna wire, wireless LAN unit or system board may each be the source of a wireless LAN fault. Any of these components may be damaged. To determine if the computer’s wireless LAN system is functioning properly, perform the following procedures. Figure 2-15 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.

Procedure 1: Diagnostic test

Procedure 2: Connector and replacement check

Procedure 1 Diagnostic test

Run the Diagnostic Program, which will automatically execute the wireless LAN test. Refer to

Chapter 3, Tests and Diagnostics for more information on the program.

If an error is located, go to Procedure 2. If an error is not located, the wireless LAN system is functioning properly.

Procedure 2 Connector and replacement check

The wireless LAN antenna, wireless LAN unit or system board may be disconnected or damaged.

Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks.

Check 1 Make sure that the wireless LAN antenna is firmly connected to the wireless LAN unit (refer to Chapter 4 for instructions) and that the wireless LAN unit is securely slotted into the system board. If the problem persists, go to Check 2.

Check 2 Check that the wireless communication switch is turned to “On”, then make sure that the wireless communication LED on the front panel is lit. If the LED is lit but the wireless LAN function is still faulty, the antenna may be damaged. Replace with a new antenna following the steps in Chapter 4, Replacement Procedures. If the problem persists, or if the wireless LAN LED is not lit when the wireless communication switch is turned to “On”, go to Check 3.

Check 3 The wireless LAN unit may be damaged. Replace it with a new one following the instructions in Chapter 4. If the problem still exists, perform Check 4.

Check 4 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4.

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

2-

37

2 Troubleshooting Procedures

2.15 Express Card Troubleshooting

START

Perform Express CARD test

(Procedure 1)

2.14 Wireless LAN Troubleshooting

Do errors occur during

Express CARD test?

No

Express unit is not faulty.

Yes

Perform Express card socket replacement check

(Procedure 2)

Replace system board

END

Figure 2-14 Express card troubleshooting process

2-38

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.14 Wireless LAN Troubleshooting 2 Troubleshooting Procedures

This section describes how to determine if the Express card player is functioning properly. The process is summarized in Figure 2-14. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required.

Procedure 1: Express card test

Procedure 2: Express socket replacement check

Procedure 1 Express card test

The Express test card contains a Express test program. Ensure the card in fully inserted into the socket before running the program.

If an error occurs during the Express card test, perform Procedure 2. If no error occurs, it is likely that the original Express card was faulty.

Procedure 2 Express card socket replacement check

The Express card socket may be damaged or defective, for instance the socket pins can be bent.

Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and replace the socket. If the problem persists, the system board may be defective or damaged.

Replace the system board with a new one following the steps in Chapter 4.

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

2-

39

2 Troubleshooting Procedures

2.12 Bluetooth Troubleshooting

START

Preform diagnostic test

(Procedure 1)

2.14 Wireless LAN Troubleshooting

Was a Bluetooth problem detect?

Bluetooth is not faulty.

Continue troubleshooting-refer to Figure 2.1

Perform connector and replacement check

(Procedure 2)

Replace Bluetooth antenna moudle.

Replace system board

END

Figure 2-16 Bluetooth troubleshooting process

2-40

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

2.14 Wireless LAN Troubleshooting 2 Troubleshooting Procedures

The Bluetooth antenna wire, Bluetooth module or system board may be the reason of a Bluetooth fault. Any of these components may be damaged. To determine if the computer’s Bluetooth is functioning properly, perform the following procedures. Figure 2-16 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.

Procedure 1: Diagnostic test

Procedure 2: Connector and replacement check

Procedure 1 Diagnostic test

Run the Diagnostic Program, which will automatically execute the Bluetooth test. Refer to

Chapter 3, Tests and Diagnostics for more information on the program.

If an error is located, go to Procedure 2. If an error is not located, the Bluetooth system is functioning properly.

Procedure 2 Connector and replacement check

The Bluetooth, antenna module or system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks.

Check 1 Make sure that the Bluetooth antenna is firmly connected to the Bluetooth module

(refer to Chapter 4 for instructions) and that the Bluetooth FFC is securely slotted into the system board. If the problem persists, go to Check 2.

Check 2 Check that the Bluetooth communication switch is turned to “On”, then make sure that the communication LED on the left panel is lit. If the LED is lit but the Bluetooth function is still faulty, the antenna module may be damaged. Replace with a new antenna following the steps in Chapter 4, Replacement Procedures. If the problem persists, or if the Bluetooth communication LED is not lit when the Bluetooth communication switch is turned to “On”, go to Check 3.

Check 3 The Bluetooth module may be damaged. Replace it with a new one following the instructions in Chapter 4. If the problem still exists, perform Check 4.

Check 4 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4.

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

2-

41

3.1The Diagnostic Test

Chapter 3

3

Tests and Diagnostics

3. Tests and Diagnostics

Satellite M70X Series Maintenance Manual 3-1

Contents

3.1 The Diagnostic Test............................................................................................................3-3

3.2 Executing the Diagnostic Test..............................................................................................3-5

3.3 Config Check Test .............................................................................................................3-9

3.4 DMI Check Test..............................................................................................................3-10

3.5 Speaker Audio Test .........................................................................................................3-11

3.6 Fan ON/OFF Test ...........................................................................................................3-13

3.7 Main Battery Charge Test.................................................................................................3-14

3.8 FDD Test.........................................................................................................................3-15

3.9 ODD Test........................................................................................................................3-16

3.10 Keyboard Test.................................................................................................................3-17

3.11 Mouse (Pad) Test ..........................................................................................................3-198

3.12 LCD Pixels Mode Test...................................................................................................3-210

3.13 Magnetic switch Test......................................................................................................3-221

3.14 HDD R/W Test..............................................................................................................3-232

3.15 LAN Test ........................................................................................................................3-25

3.16 RTC Test.......................................................................................................................3-276

3.17 Speaker EQ Check&Rewrite .........................................................................................3-317

3.18 Read 1394 GUID…………...………………………………………………...………...3-29

3.19 CD Control Button Test………………………………………………………………..3-30

3-2 satellite M750X Series Maintenance Manual

3.1The Diagnostic Test 3. Tests and Diagnostics

3.1 The Diagnostic Test

This chapter explains how to use the Test & Diagnostic program to test the functions of the (Base on

Detroit10 T&D version 1.0) hardware modules. The Test & Diagnostic Program is stored on the

T&D diskettes. The program consists of a series of tests that run automatically when the Diagnostics

Program items are selected and executed.

NOTES:

To start the diagnostics, follow these steps

1. Check all cables for loose connections.

2. Exit this program when you are at Main Menu.

The TEST & DIAGNOSTIC PROGRAM contains the following functional tests:

? CONFIG CHECK TEST

? DMI CHECK TEST

? SPEAKER AUDIO TEST

? FAN ON/OFF TEST

? MAIN BATTERY CHARGE TEST

? FDD TEST

? ODD TEST

? KEYBOARD TEST

? MOUSE(PAD) TEST

? LCD PIXELS MODE TEST

? MAGNETIC SWITCH TEST

? HDD R/W TEST

? LAN TEST

? RTC TEST

? IEEE1394 CODE TEST

? Speaker EQ Check&Rewrite

? Button Test

You will need the following equipment to perform some of the Diagnostic test programs.

? The diagnostics diskette (2 pcs)

? A formatted working diskette for the floppy disk drive test (Floppy Disk Drive Test)

? A data CD disc (ODD Test)

? A LAN loopback connector (LAN Test)

The following sections explain how to execute the Test & Diagnostic Program and detail the tests within the program.

Satellite M70X Series Maintenance Manual 3-3

3-4 satellite M750X Series Maintenance Manual

3.2 Executing the Diagnostic Test 3. Tests and Diagnostics

3.2 Executing the Diagnostic Test

Toshiba MS-DOS is required to run the DIAGNOSTICS PROGRAM. To start the DIAGNOSTIC

PROGRAM, follow these steps:

1. Insert the diagnostics diskette #1 in the floppy disk drive and turn on the computer. (The diagnostics diskette contains the MS-DOS boot files.) And then follow the instructions to swap with the diagnostics diskette #2 for T&D program installed in RAM driver.

NOTE: To execute the CD test, make sure the CD is installed in the ODD drive.

The T&D Program can run by single test item when you press corresponsive English letter of test item, or run two or more test items what you like if you choose them by “Arrow cursors” and “Space Bar” – the wonderful thing is you can setup test loop by “Enter” button. And it also asks you if you like to copy test log file to diskette as reference at the end of test(s).

The test list is as the following:

A. CONFIG CHECK TEST

B. DMI CHECK TEST

C. RTC TEST

D. LAN TEST

E. SPEAKER AUDIO TEST

F. FAN ON/OFF TEST

G. MAIN BATTERY CHARGE TEST

H. FDD TEST

I. ODD TEST

J. KEYBOARD TEST

K. MOUSE (PAD) TEST

L. LCD PIXELS MODE TEST

M. MAGNETIC SWITCH TEST

N. HDD R/W TEST

O. IEEE1394 CODE TEST

P. Speaker EQ Check&Rewrite

Q. Button test

Satellite M70X Series Maintenance Manual 3-5

3. Tests and Diagnostics 3.2 Executing the Diagnostic Test

The below display will show up at the beginning of T&D program

If the test result passes, the following display will show up:

3-6 satellite M750X Series Maintenance Manual

3.2 Executing the Diagnostic Test

If an error is detected and a test fails, the following message displays:

3. Tests and Diagnostics

Then press any key for next actions – the below display presented if copying test log file onto diskette is necessary. This action will be executed when “Y” key pressed.

Satellite M70X Series Maintenance Manual 3-7

3. Tests and Diagnostics 3.2 Executing the Diagnostic Test

It will skip this process if “N” key pressed.

And then it will check if it’s necessary to leave this program. Program will quit when “Y” key pressed and it will go back main menu for next test if “N” key pressed.

NOTE: Press Pause to pause a test and Enter to resume.

3-8 satellite M750X Series Maintenance Manual

3.1 Config check Test 3. Tests and Diagnostics

3.3 Config Check Test

The config check test checks unit configuration. It includes:

? CPU type (P4/CEL; Dothan; Cache ; CPU speed )

? BIOS version

? Panel ID

? VRAM size

? System memory size (*** MB)

? ODD type (DVD-SuperMulti; COMBO; …)

? HDD type & capacity (Vendor ID. Model .Firmware)

? Wireless type

? LAN Type (LAN10/100)

? Battery cell

This test needs input unit Part Number by manual to make comparison with known SKU data.

NOTE: To execute this test, you must input unit Part Number as “Uppercase Character”.

Then it will show its configuration is correct (in

green

color) or failed (in

red

color).

The screen should display as below, indicating whether the test is passed or failed after comparison.

Satellite M70X Series Maintenance Manual 3-9

3. Tests and Diagnostics 3.1 Config check Test

3.4 DMI Check Test

This test will check if the computer’s Desktop Management Interface (DMI) is correct.

DMI includes:

? Manufacturer

? Production Name

? Version

? Serial Number

? UUID

? OEM String

It needs to input unit Part Number by manual, then show this unit DMI information and makes comparison with SKU data.

NOTE: To execute this test, you must input unit Part Number as “Uppercase Character”.

3-10 satellite M750X Series Maintenance Manual

3.1 Config check Test 3. Tests and Diagnostics

The screen should display as below, indicating whether the test is passed or failed after comparison.

3.5 Speaker Audio Test

The speaker audio test allows the user to aurally confirm the speaker functions. And check both speakers if they are OK within 3 times “Beep” sound generated.

NOTE: Remember to tune up the volume as “Maximum” before this test starts.

The screen should display as below, indicating whether the test is passed or failed after the question.

Satellite M70X Series Maintenance Manual 3-11

3. Tests and Diagnostics 3.1 Config check Test

3-12 satellite M750X Series Maintenance Manual

3.8 Fan ON/OFF Test 3. Tests and Diagnostics

3.6 Fan ON/OFF Test

The fan test allows the user to test aurally whether the fan is working. And follow the below procedures for this test:

? The computer will let the fan be “ON” after any key pressed. Listen to check whether the fan is working.

NOTE: Remember to approach fan outlet that is near right side of unit whether fan is

“ON”.

? The computer will stop the fan working after any key pressed. Listen to check if the fan is “OFF” – it means no rotating sound.

The screen should display as below, indicating whether the test is passed or failed after the question.

Satellite M70X Series Maintenance Manual 3-13

3. Tests and Diagnostics 3.9 Main Battery Change Test

3.7 Main Battery Charge Test

NOTE: The AC adaptor (65W, 19V) should be connected to successfully run this test.

This test shows and measures the main battery:

? Battery type (Lion)

? Manufacturer (Sanyo/Panasonic)

? Remain charge capacity (0 ~ 100%)

? Charge function (PASS/FAIL)

- “Battery Is Full” showed when “remain charge capacities” is 100%

The screen should display as below, indicating whether the test is passed or failed when finished.

3-14 satellite M750X Series Maintenance Manual

3.10 FDD Test 3. Tests and Diagnostics

3. 8 FDD Test

NOTE: Before running the FDD test, prepare a formatted work diskette (1.44 MB).

Remove the diagnostics diskette and insert the work diskette into the FDD. The contents of the floppy diskette maybe erased.

The Floppy Disk Test includes three subtests of the:

1. Sequential seek/verify function (Range: Track 0 ~ 79)

2. Funnel code seek/verify function (Range: Track 0 ~ 79)

3. Write/Read/Compare pattern function (Range: Track 75 ~ 79)

NOTE: The write-protected device of this formatted diskette should be “Disable”.

The subtests run automatically.

NOTE: Press “Esc” key can skip the current subtest.

The screen should display as below, indicating whether the subtests pass or fail when finished.

Satellite M70X Series Maintenance Manual 3-15

3. Tests and Diagnostics 3.11 ODD Test

3. 9 ODD Test

The ODD test allows a user to aurally confirm the ODD functions.

NOTE: A CD disc (including data file) must be inserted into the ODD drive before this test starts.

The ODD test includes two subtests of the:

1. Random read/partial sequential read function

2. Sequential read function (for all surface)

Each item can be chosen by manual. When each test item finished, the ODD tray will open. Check whether the tray can open automatically.

NOTE: Press “Esc” key can skip the current subtest.

The screen should display as below, indicating whether the subtests pass or fail when finished.

3-16 satellite M750X Series Maintenance Manual

3.12 Keyboard Test 3. Tests and Diagnostics

3. 10 Keyboard Test

The keyboard test checks the all keys function.

NOTE: The Num Lock and the Overlay mode must be off to execute the keyboard test.

Before keyboard test starts, the keyboard matrix code should be chosen as below display:

1. K (UK, for Europe)

2. S (US, for America)

When you execute this test, the keyboard layout is drawn on the display. When any key is pressed, the corresponding key on the screen changes to black as shown below.

It will indicate whether the subtest is passed or failed after the question.

NOTE: The “Fn” key cannot be tested in the keyboard test. To determine whether the

Fn key is working correctly, press “Fn+F6 ” or “Fn+F7 ” keys to check if LCD display brightness change gradually.

Satellite M70X Series Maintenance Manual 3-17

3. Tests and Diagnostics 3.12 Keyboard Test

3-18 satellite M750X Series Maintenance Manual

3.13 Mouse (Pad) Test 3. Tests and Diagnostics

3.11 Mouse (Pad) Test

The Mouse test allows the user to select and assign values to the following, using the Touch Pad or

Tab key to move between selections:

1. Mouse Speed (on a scale from slow to fast)

2. Acceleration (Off, Low, Medium, High)

3. Button Assignments (Left + Right / Right button, either Unassigned or Drag Lock)

4. Swap Buttons (Left /Right)

NOTE: The Touch Pad test cannot be used to test an external USB mouse.

The Touch Pad button subtest allows users to test their Touch Pad buttons. If the buttons are clicked, the cursors should appear in the corresponding box of the button figure that is displayed on the screen as below.

Satellite M70X Series Maintenance Manual 3-19

3. Tests and Diagnostics 3.13 Mouse (Pad) Test

After checking T/Pad buttons and cursor’s function, use “Tab” key or use T/Pad cursor to click the

“OK” column will end this test.

It will indicate whether the subtests pass or fail after three questions.

NOTE: The above figure has three compartments although the Touch Pad installed may only have two buttons. In this case, the central compartment in the figure does not correspond to any button.

3-20 satellite M750X Series Maintenance Manual

3.14 LCD Pixels Mode Test 3. Tests and Diagnostics

3. 12 LCD Pixels Mode Test

This LCD pixels mode test checks whether video display is fine.

This test includes two modes of the test:

1. Text Mode

- including 40*25 (16 colors) and 80*25 (2/16colors).

2. VGA Mode

- including 320*200 (4/16/256 colors), 640*200 (2/16 colors), 640*350 (2/16 colors),

640*480 (2/16/256 colors), 800*600 (256 colors) and 1024*768 (256 colors).

The screen should display as below, indicating whether the test is passed or failed after the question.

Satellite M70X Series Maintenance Manual 3-21

3. Tests and Diagnostics 3.15 Lid Switch Test

3.13 Magnetic Lid Switch Test

The lid switch test checks the lid function of the unit. When LCD cover closed, the lid should enable to turn off the display.

NOTE: Remember to tune up the volume as “Maximum” before this test starts.

Follow below steps to run this test:

1. Close the LCD cover.

2. Heard 3 “Beep” sound happened during LCD closed.

3. Open the LCD.

Then it will indicate whether the test is passed or failed.

3-22 satellite M750X Series Maintenance Manual

3.16 HDD R/W Test 3. Tests and Diagnostics

3.14 HDD R/W Test

The HDD R/W test allows the user to test aurally HDD read/write function. For data security concern, it is necessary to input password - “hard disk” before HDD write test starts.

The HDD test includes three subtests of the:

1. Sequential read (all surface)

2. Sequential write (all surface)

3. Partial W/R + Random W/R

After the choice is made, HDD information will show as below:

?

Model name

?

?

Firmware revision

Serial number

?

?

?

CHR (Cylinder High Register) mode – including cylinders, heads, sectors and sizes.

LBA (Logical Block Addressing) mode – including sectors and sizes.

Support Ultra DMA Mode

Satellite M70X Series Maintenance Manual 3-23

3. Tests and Diagnostics 3.16 HDD R/W Test

NOTE: Press “Ctrl + Break” keys can terminate the current subtest.

The screen should display as previous picture, indicating whether the subtest is passed or failed when finished.

NOTE: The AC adaptor should be connected to successfully run this test.

3-24 satellite M750X Series Maintenance Manual

3.17 LAN Test 3. Tests and Diagnostics

3.15 LAN Test

The LAN test checks the LAN full-duplex environment.

NOTE: LAN loopback needs to plug in before test begins.

And LAN information will show on the test screen:

?

IO Base – Port: 3000H

?

?

IRQ – AH, it’s “IRQ 10”.

Node – it is “MAC Address”.

?

?

?

Line Frame – 1514 Bytes.

Line Speed – 100Mbps or 10 Mbps.

Bus ID – it’s “4”.

The LAN test includes two subtests of the:

1. Speed100

- Including Ethernet_802.2, Ethernet II, Ethernet SNAP and Ethernet_802.3. All test items are in LSB mode.

2. Speed10

- Including Ethernet_802.2 in LSB mode.

The subtests run automatically.

Satellite M70X Series Maintenance Manual 3-25

3. Tests and Diagnostics 3.17 LAN Test

The screen should display as below, indicating whether the subtests pass or fail when finished.

If an error is detected and a test fails, the following message displays:

3-26 satellite M750X Series Maintenance Manual

3.18 RTC Test 3. Tests and Diagnostics

3.16 RTC Test

Checks the computer’s RTC (Real Time Clock) and calendar functions by comparing the DOS and

CMOS values.

The test runs automatically.

The screen should display as below, indicating whether the test is passed or failed when finished.

Satellite M70X Series Maintenance Manual 3-27

3. Tests and Diagnostics

3.17 Speaker EQ Type Check&Re-Write

This test will check if the computer’s EEPROM EQ type is correct.

The EQ Type test includes two subtests of the:

1. Read EQ Type from EEPROM

2. Re-Write EQ Type to EEPROM

NOTE: To execute this test, you must select speaker type (Harman or No brand).

The figure below will be displayed:

3.18 RTC Test

3-28 satellite M750X Series Maintenance Manual

3.18 RTC Test

The Item2 figure below will be displayed:

3. Tests and Diagnostics

NOTE: Write speaker EQ must reboot to enable EQ.

Satellite M70X Series Maintenance Manual 3-29

3. Tests and Diagnostics 3.18 RTC Test

3.18 Read 1394 GUID

This test will check if the computer’s EEPROM 1394GUID code is correct.

NOTE: Must open the RAM Door to see RAM connector GUID bar code before test item begins.

The figure below will be displayed:

3-30 satellite M750X Series Maintenance Manual

3.19 CD Control Button Test 3. Tests and Diagnostics

3.19 CD Control Button Test

The CD control button test allows the user to manually test each of the five CD control buttons.

Key ”WWW” need to press first. One will hear one “bi” sound when press”WWW” or “Audio”

Sound and continuously “bi” sound for another key test.

The figure below will be displayed:

Press each of the buttons on the front panel in turn. A yellow bar will appear on the relevant section of the figure if the button passes the test.

Press Ctrl +C to quit the test.

Satellite M70X Series Maintenance Manual 3-31

4

Chapter 4

Replacement Procedures

4 Replacement Procedures

4-ii

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4 Replacement Procedures

Chapter 4 Contents

4.1 General........................................................................................................................ 4-7

4.2 Battery ...................................................................................................................... 4-13

4.3 PC Card.................................................................................................................... 4-15

4.4 HDD ......................................................................................................................... 4-17

4.5 Modem ..................................................................................................................... 4-20

4.6 Expansion Memory.................................................................................................... 4-21

4.7 Wireless LAN Unit .................................................................................................... 4-23

4.8 Optical Drive Module ................................................................................................ 4-25

4.9 Optical Drive ............................................................................................................. 4-27

4.10 Keyboard.................................................................................................................. 4-29

4.11 Display Assembly ...................................................................................................... 4-32

4.12 Bluetooth ................................................................................................................... 4-36

4.13 Top Cover................................................................................................................. 4-38

4.14 TouchPad .................................................................................................................. 4-41

4.15 System Board............................................................................................................ 4-43

4.16 Speakers ................................................................................................................... 4-47

4.17 VGA Board............................................................................................................... 4-48

4.18 Thermal Module ........................................................................................................ 4-50

4.19 Fan, CPU & Heat Sink .............................................................................................. 4-51

4.20 Display Mask ............................................................................................................ 4-54

4.21 LCD Module ............................................................................................................. 4-56

4.22 FL Inverter Board...................................................................................................... 4-58

Satellite M70/Satellite Pro M70 Series Maintenance Manual [CONFIDENTIAL] 4-iii

4 Replacement Procedures

Figures

Figure 4-1 Removing the battery pack ............................................................................. 4-13

Figure 4-2 Pressing the eject button................................................................................. 4-15

Figure 4-3 Installing the PC card...................................................................................... 4-16

Figure 4-4 HDD.............................................................................................................. 4-17

Figure 4-5 Removing the HDD unit.................................................................................. 4-17

Figure 4-6 Removing the HDD unit.................................................................................. 4-18

Figure 4-7 Removing the Modem.................................................................................... 4-20

Figure 4-8 Removing the expansion memory.................................................................... 4-21

Figure 4-9 Installing the expansion memory...................................................................... 4-22

Figure 4-10 Removing the wireless LAN door ................................................................... 4-23

Figure 4-11 Removing the wireless LAN card.................................................................... 4-23

Figure 4-12 Removing the optical drive module ..................................................................4-25

Figure 4-13 Removing the optical drive bracket.................................................................4-27

Figure 4-14 Removing the strip cover ................................................................................ 4-29

Figure 4-15 Removing the keyboard.................................................................................. 4-30

Figure 4-16 Disconnecting the keyboard cable ................................................................... 4-30

Figure 4-17 Disconnecting the LCD cable .......................................................................... 4-32

Figure 4-18 Removing the keyboard door.......................................................................... 4-32

Figure 4-19 Pulling out the wireless LAN antennas............................................................. 4-33

Figure 4-20 Removing the screws from the backside .......................................................... 4-33

Figure 4-21 Removing the display assembly ....................................................................... 4-34

Figure 4-22 Removing the Bluetooth module ...................................................................... 4-36

Figure 4-23 Removing the top cover-1 .............................................................................. 4-38

Figure 4-24 Removing the top cover-2 .............................................................................. 4-39

Figure 4-25 Removing the top cover-3 .............................................................................. 4-39

Figure 4-26 Removing the TouchPad................................................................................. 4-41

Figure 4-27 Removing the system board............................................................................ 4-43

Figure 4-28 Removing the hexagonal screws ...................................................................... 4-44

Figure 4-29 Removing the audio board .............................................................................. 4-44

Figure 4-30 Removing the ODD board.............................................................................. 4-45

Figure 4-31 Removing the speakers ................................................................................... 4-47

4-iv

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4 Replacement Procedures

Figure 4-32 Removing the VGA Board-1.......................................................................... 4-48

Figure 4-33 Removing the VGA Board-2.......................................................................... 4-49

Figure 4-34 Removing the Thermal Module ....................................................................... 4-50

Figure 4-35 Removing the CPU........................................................................................ 4-51

Figure 4-36 Removing the fan ........................................................................................... 4-51

Figure 4-37 Removing the fan botton................................................................................. 4-52

Figure 4-38 Removing the heat sink ................................................................................... 4-52

Figure 4-39 Removing the heat sink ................................................................................... 4-53

Figure 4-40 Removing the display mask ............................................................................ 4-54

Figure 4-41 Removing the LCD module-1......................................................................... 4-56

Figure 4-42 Removing the FL inverter board..................................................................... 4-58

Satellite M70/Satellite Pro M70 Series Maintenance Manual [CONFIDENTIAL] 4-v

4 Replacement Procedures

4-vi

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.1 General 4 Replacement Procedures

4.1 General

This chapter explains how to disassemble the computer and replace Field Replaceable Units

(FRUs). It may not be necessary to remove all the FRUs in order to replace one. The chart below is a guide to which FRUs need to be removed in order to remove others. Always start by removing the battery pack, next, optional items such as the optional PC Card, then follow the chart downward removing only those FRUs necessary to reach the one you think is causing the computer to operate improperly. Refer to the example on the following page.

Battery pack

Keyboard Wireless LAN

HDD and/or

Modem

ODD and/or Expansion

Memory Module

Bluetooth Display Assembly

Top Cover

System Board

Display Mask

LCD Module

VGA Board

Fan & Heat Sink

Speakers

CPU

Touch Pad

FL Inverter Board

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-7

4 Replacement Procedures 4.1 General

The example below shows FRUs to be removed before the Speakers can be removed and repaired or replaced. The Speakers are overlapped by the top cover that must be removed before it can be reached. The removable keyboard, and display assembly in turn overlap the top cover. Always starts the disassembly process by removing the battery pack.

Battery pack

Keyboard Wireless LAN

HDD and/or

Modem

ODD and/or Expansion

Memory Module

Bluetooth Display Assembly

Top Cover

System Board

Display Mask

LCD Module

VGA Board

Fan & Heat Sink

Speakers

CPU

Touch Pad

FL Inverter Board

4-8

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.1 General 4 Replacement Procedures

Safety Precautions

Before you begin disassembly, read the following safety precautions and observe them carefully as you work.

DANGER:

1. Always use the lithium ion battery pack or backup battery that is authorized by

Toshiba or compatible with the unit. Since other battery packs have different specifications, they may be incompatible with the unit, and may burst or explode.

Heating or disassembling the battery pack could cause leakage of alkaline solution.

Throwing the battery pack into a fire could cause the battery pack to explode.

2. The power supply, FL inverter and other components carry high voltages. To avoid the risk of electric shock when you need to turn on the power of a partially disassembled computer to check its operation, be very careful not to touch connectors or components. Also, do not disassemble individual components in first-

level maintenance.

WARNING: To avoid the risk of electric shock or other injury:

1.

Always turn the power off and disconnect the AC adaptor from the power source.

2. Remove any metal jewelry or accessories such as necklaces, bracelets, or rings.

Batteries in the computer retain an electrical charge so there is danger of electrical

shock even when the computer is disconnected from an AC power source.

3.

Never work with wet or damp hands.

4.

The computer contains sharp edges and corners: be careful not to injure yourself.

5. Make sure that all replacement components meet the specifications for the computer

and that all cables and connectors are securely fastened.

CAUTION: To avoid damage to the computer:

1. When you change a component, be sure the replacement component meets the required

specifications. Never use foreign parts.

2. Metal objects such as screws or paper clips which fall into the unit can cause a short-

circuit, fire, or other internal damage.

3. When assembling the computer, make sure you use the correct screws to secure the various pieces in place. Screw sizes are listed in their corresponding figure. Make sure all screws are securely fastened. Loose screws can cause short circuits, resulting in

heat, smoke, or fire.

4. Before removing an FRU or other component, make sure all cables to the component

have been disconnected.

5. If you use AC power, be sure to use the cable that came with the computer or one

recommended by Toshiba.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-9

4 Replacement Procedures 4.1 General

Before You Begin

Look over the procedures in this section before you begin disassembling the computer. Familiarize yourself with the disassembly and reassembly steps. Begin each procedure by removing the AC adaptor and the battery pack as instructed in section 4.2.

1. Do not disassemble the computer unless it is operating abnormally.

2. Use only the correct and approved tools.

3. Make sure the working environment is free from the following elements whether you are using or storing the computer.

?

Dust and contaminates

?

Static electricity

?

Extreme heat, cold and humidity

4. Make sure the FRU you are replacing is causing the abnormal operation by performing the necessary troubleshooting and diagnostics tests described in chapters 2 and 3 of this manual.

5. Do not perform any operations that are not necessary and use only the described procedures for disassembling and installing FRUs in the computer.

6. After removing parts from the computer, place them in a safe place away from the computer so they will not be damaged and will not interfere with your work.

7. You will remove and replace many screws when you disassemble the computer. When you remove screws, make sure they are placed in a safe place and identified with the correct parts.

8. When assembling the computer make sure you use the correct screws to secure the various pieces. Screw sizes are listed in their corresponding figures.

9. The computer contains many sharp edges and corners, so be careful not to injure yourself.

10. After you have replaced an FRU, make sure the computer is functioning properly by performing the appropriate test on the FRU you have fixed or replaced.

4-10

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.1 General 4 Replacement Procedures

Disassembly Procedures

The computer has two basic types of cable connectors:

?

Pressure Plate Connectors

?

Standard Pin Connectors

To disconnect a Pressure Plate connector, lift up the tabs on either side of the connector’s plastic pressure plate and slide the cable out of the connector. To connect the cable to a Pressure Plate connector, make sure the pressure plate is fully lifted and slide the cable into the connector. Secure the cable in place by pushing the sides of the pressure plate down so the plate is flush with the sides of the connector. Gently pull on the cable to make sure the cable is secure. If you pull out the connector, connect it again making sure the connector’s pressure plate is fully lifted when you insert the cable.

Standard pin connectors are used with all other cables. These connectors can be connected and disconnected by simply pulling them apart or pushing them together.

Assembly Procedures

After you have disassembled the computer and fixed or repaired the problem that was causing the computer to operate abnormally, you will need to reassemble the computer.

Install all the removed FRUs following the steps described in the corresponding sections in this chapter.

While assembling the computer, remember the following general points:

?

Take your time, making sure you follow the instructions closely. Most problems arise when you get in a hurry assembling the computer.

?

Make sure all cables and connectors are securely fastened.

?

Before securing the FRU or other parts, make sure that no cables will be pinched by screws or the FRU.

?

Check that all latches are closed securely.

?

Make sure all the correct screws are used to secure all FRUs. Using the wrong screw can either damage the threads on the screw or the head of the screw and may prevent proper seating of an FRU.

After installing an FRU in the computer, confirm that the FRU and the computer are functioning properly.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-11

4 Replacement Procedures 4.1 General

Tools and Equipment

The use of Electrostatic Discharge (ESD) equipment is very important for your safety and the safety of those around you. Proper use of these devices will increase the success rate of your repairs and lower the cost for damaged or destroyed parts. The following equipment is necessary to disassemble and reassemble the computer:

?

One M2 Phillips screwdriver to remove and replace screws.

?

One T8 security screwdriver.

?

Tweezers, to lift out screws that you cannot grasp with your fingers.

?

ESD mats for the floor and the table you are working on.

?

ESD wrist strap or heel grounder.

?

Anti-static carpeting or flooring.

?

Air-ionizers in highly static sensitive areas.

4-12

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.2 Battery 4 Replacement Procedures

4.2 Battery

Removing the Battery Pack

To remove the battery pack from the battery bay, follow the steps below.

1. Turn the computer upside down.

2. Disengage the battery lock (A) and slide the battery bay latch (B) to release the battery pack.

Then you can remove it from the bay (C).

Figure 4-1 Removing the battery pack

NOTE: For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to Toshiba.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-13

4 Replacement Procedures 4.2 Battery

Installing the Battery Pack

To install the battery pack in the battery bay, follow the steps below and refer to the figure in the preceding section.

WARNING: The battery is a lithium ion battery and can explode if not properly replaced, used, handled or disposed of. Use only batteries recommended by Toshiba as replacements.

1. Slide the battery pack into the battery bay. The battery bay latch clicks into place automatically.

4-14

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.3 PC Card

4.3 PC Card

Removing a PC Card

To remove a PC Card, follow the steps below.

1. Click the Safely Remove Hardware icon on the Task Bar.

2. Click the PC Card you want to remove.

3. Press the eject button of the PC Card to extend it.

4. Press the extended eject button to pop the card out slightly.

5. Grasp the PC Card and remove it.

4 Replacement Procedures

Figure 4-2 Pressing the eject button

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-15

4 Replacement Procedures 4.3 P C Card

Installing the PC Card

To install the PC Card, follow the steps below and refer to the figures in the preceding section.

1. Insert the PC Card.

2. Press gently to ensure a firm connection.

Figure 4-3 Installing the PC card

4-16

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.4 HDD 4 Replacement Procedures

4.4 HDD

CAUTION: When handling the HDD, do not press the top surface as shown by the arrow.

Hold it by the sides.

Figure 4-4 HDD

Removing the HDD Module

Follow the steps below to remove HDD module:

1. Turn the computer upside down

2. Remove three black M2.5x4 safety screws to release the HDD door.

3. Remove two M2.5x3 screws from HDD.

4. Pull on the tab to remove the HDD unit.

Figure 4-5 Removing the HDD unit

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-17

4 Replacement Procedures

5. Remove four M3x3 silver screws that secure the EMI Shielding to the HDD.

4.4 HDD

Figure 4-6 Removing the HDD unit

6. Remove the HDD from the EMI Shielding.

4-18

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.4 HDD 4 Replacement Procedures

Installing the HDD

To install the HDD, follow the steps below and refer to the figures in the preceding section.

1. Seat the HDD in the EMI Shielding, and secure it with four M3x3 black screws.

2. Insert the HDD unit into the HDD slot.

3. Secure the HDD with two black M2.5x3 screws.

4. Secure the HDD door with three black M2.5x4 safety screws.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-19

4 Replacement Procedures 4.5 Modem

4.5 Modem

Removing the Modem

To remove the modem, you need to remove the HDD door first, described in the preceding section.

Follow the steps below:

1. Remove two black M2.5x3 screws securing the modem to the chassis.

Figure 4-7 Removing the Modem

2. Disconnect the RJ-11 wire, then remove the modem.

Installing the Modem

To install a modem, follow the steps below and refer to the figures in the preceding section.

1. Connect the modem cable to the modem module.

2. Fit the modem onto its connector and secure it with two black M2.5x3 screws.

4-20

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.6 Expansion Memory 4 Replacement Procedures

4.6 Expansion Memory

Removing the Expansion Memory

To remove the memory module, make sure the computer is in boot mode:

1. Remove one M2.5x4 screw securing the expansion memory compartment cover.

2. Push the latches securing the memory module to the outside to release it (A). A spring will force one end of the module up (B).

3. Grasp the module and pull it out (C).

4. Seat the cover and secure its screws.

Figure 4-8 Removing the expansion memory

CAUTION: Do not touch the connectors on the expansion memory or on the computer. Debris on the connectors may cause memory access problems.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-21

4 Replacement Procedures 4.6 Expansion Memory

Installing the Expansion Memory

CAUTION: Do not touch the connectors on the expansion memory or on the computer. Debris on the connectors may cause memory access problems.

To install a memory module, follow the steps below and refer to the figures in the preceding section:

1. Fit the module's connectors into the computer's connectors at about a 45-degree angle and press the module carefully to ensure a firm connection (A).

2. Push the module down so it lies flat (B). Latches on either side will click into place to secure the module.

Figure 4-9 Installing the expansion memory

4-22

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.7 Wireless LAN Unit 4 Replacement Procedures

4.7 Wireless LAN Unit

Removing the Wireless LAN Unit

To remove wireless LAN unit:

1. Remove the M2.5x4 screw securing the wireless LAN door, and then remove it. (NOTE: The

Satellite Pro M70 may have an embedded safety screw.)

Figure 4-10 Removing the wireless LAN door

2. Disconnect the antenna wires from the wireless LAN module.

Figure 4-11 Removing the wireless LAN card

3. Use your fingers to press the two latches of LAN unit container. The LAN unit will pop up.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-23

4 Replacement Procedures 4.7 Wireless LAN Unit

4. Grasp the wireless LAN unit and pull it out.

CAUTION: Do not touch the connectors on the wireless LAN unit or on the computer. Debris on the connectors may cause malfunction.

Installing the Wireless LAN Unit

To install the wireless LAN unit, follow the steps below and refer to the figures in the preceding section.

1. Remove the screw M2.5x4 securing the wireless LAN door, and then remove it. (NOTE: The

Satellite Pro M70 has an embedded safety screw.)

CAUTION: Do not touch the connectors on the wireless LAN unit or on the computer. Debris on the connectors may cause malfunction.

2. Gently, push the wireless LAN unit into the wireless LAN container. The two latches of container will automatically close up.

3. Attach the white antenna to the main connector, and the black antenna to the Aux connector.

4-24

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.8 Optical Drive Module 4 Replacement Procedures

4.8 Optical Drive Module

Removing the Optical Drive Module

To remove the optical drive module, you need to open the expansion memory compartment first.

Follow the steps below:

1. Turn the computer upside down.

2. Remove the screw M2.5x6 securing the optical drive module.

3. Use your hand to pull the module and then you can slide the module from the bay.

Figure 4-12 Remov ing the optical drive module

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-25

4 Replacement Procedures 4.8 Optical Drive Module

Installing the Optical Drive Module

To install a device in the optical drive module bay, follow the steps below and refer to the figure in the preceding section.

1. Slide the device into the optical drive module bay.

2. Use one M2.5x6 screw to secure the optical drive module.

4-26

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.9 Optical Drive 4 Replacement Procedures

4.9 Optical Drive

This computer may be fitted with a: CD-RW/DVD-ROM drive

DVD Super Multi drive

Disassembling the Optical Drive

To disassemble the optical drive, first remove the drive from its module bay, then follow the steps below.

1. Remove two black M2x3 screws from the bracket plate. Remove the bracket plate.

Figure 4-13 Removing the optical drive bracket

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-27

4 Replacement Procedures 4.9 Optical Drive

Reassembling the Optical Drive

To reassemble an optical drive, follow the steps below and refer to the figure in the preceding section.

1. Position the optical drive bracket plate to the rear panel of optical drive.

2. Secure the optical drive bracket plate with two black M2x3 screws.

4-28

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.10 Keyboard 4 Replacement Procedures

4.10 Keyboard

Removing the Keyboard

Follow the steps below to remove the keyboard:

1. Open the display panel.

2. Insert a thin tool into the gap between the strip cover and keyboard to lever the strip cover up and then release the strip cover.

Figure 4-14 Removing the strip cover

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-29

4 Replacement Procedures

3. Remove two M2x3 black screws securing the keyboard.

4.10 Keyboard

Figure 4-15 Removing the keyboard

4. Disconnect the keyboard FPC cable and remove the keyboard.

Figure 4-16 Disconnecting the keyboard cable

4-30

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.10 Keyboard 4 Replacement Procedures

Installing the Keyboard

To install the keyboard, follow the steps below and refer to the figures in the preceding section.

1. Connect the keyboard FPC cable to the system board.

2. Set the keyboard in place and secure it with two M2x3 black screws.

3. Set the strip cover and press down to secure the strip cover latches engage.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-31

4 Replacement Procedures 4.12 Bluetooth

4.11 Display Assembly

Removing the Display Assembly

To remove the display assembly, first remove the keyboard and wireless LAN, then follow the steps below:

1. Disconnect the LCD power cable from the top chassis.

Figure 4-17 Disconnecting the LCD cable

2. Remove the keyboard door on the left hand side of the computer chassis.

Figure 4-18 Remov ing the keyboard door

4-32

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.12 Bluetooth

3. Pull out the wireless LAN antennas.

4 Replacement Procedures

Figure 4-19 Pulling out the wireless LAN antennas

4. From the backside, remove two M2.5x12 screws securing the LCD.

Figure 4-20 Removing the screws from the backside

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-33

4 Replacement Procedures 4.12 Bluetooth

5. Remove two M2.5x6 screws securing display assembly to the top cover, the disengage the display assembly from the chassis.

Figure 4-21 Removing the display assembly

4-34

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.12 Bluetooth 4 Replacement Procedures

Installing the Display Assembly

To install the display assembly, follow the steps below and refer to the figures in the preceding section.

1. Seat the display assembly taking care not to crush to the LCD power cable or wireless LAN antenna.

2. Secure two M2.5x6 black screws to each hinge on the topside.

3. Secure two M2.5x12 black screws to the computer’s backside.

4. Connect the LCD power cable to the top chassis.

5. Thread the wireless LAN antennas back into their hole.

6. Restore the keyboard door.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-35

4 Replacement Procedures 4.12 Bluetooth

4.12 Bluetooth

Removing the Bluetooth module

To remove the Bluetooth module, first remove the keyboard as described in the preceding section and then follow the steps below:

1. Disconnect the antenna wire from the antenna connector.

2. Disconnect the Bluetooth FFC.

3. Remove two black M2x3 screws securing the Bluetooth module to the chassis.

Figure 4-22 Removing the Bluetooth module

4-36

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.12 Bluetooth 4 Replacement Procedures

Installing the Bluetooth module

To install the Bluetooth module, follow the steps in the below and refer to the figures in the preceding section.

1. Seat the Bluetooth module on the chassis, then secure it with two black M2x3 screws.

2. Connect the Bluetooth FFC to the module.

3. Connect the antenna wire to the antenna connector.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-37

4 Replacement Procedures 4.13 Top Cover

4.13 Top Cover

Removing the Cover

To remove the top cover, first remove the battery pack, keyboard, display assembly, optical drive module, HDD, and memory module and wireless LAN as described in the preceding sections, then follow the steps below:

1. Remove one M2.5x13 screw, two M2.5x6 screws, and one M2.5x3 screw securing top cover.

Figure 4-23 Removing the top cover-1

4-38

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.13 Top Cover 4 Replacement Procedures

2. Detach the Power Switch FFC cable and TouchPad FFC cable on the top chassis.

Figure 4-24 Removing the top cover-2

3. Turn the computer upside down and remove eleven M2.5x12, four M2.5x8 screws and one

M2.5x3 screw securing the bottom cover to the top cover.

Figure 4-25 Removing the top cover-3

4. Turn the computer upright to lift off the top cover.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-39

4 Replacement Procedures 4.13 Top Cover

Installing the Top Cover

To install the top cover, follow the steps below and refer to the figures in the preceding section.

1. Seat the top cover and secure the upper FFC cable and Touch pad FFC cable to the computer’s top chassis.

2. Secure the top cover with one M2.5x1 3 screw, two M2.5x6 screws, and one M2.5x3 screw.

3. Turn the computer upside down and secure eleven M2.5x12 screws, four M2.5x8 and one

M2.5x3 screw.

4-40

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.14 TouchPad 4 Replacement Procedures

4.14 TouchPad

Removing the TouchPad

To remove the TouchPad, first remove the top cover, then follow the steps below:

1. Disconnect the TouchPad FFC cable from the TouchPad.

2. Remove two M2.5x3 black screws securing the control button board. Slide it and lift it out.

3. Remove one M2.5x3 screw securing the TouchPad Bracket. Slide it and lift out the TouchPad

Bracket.

Figure 4-26 Removing the TouchPad

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-41

4 Replacement Procedures 4.14 TouchPad

Installing the TouchPad

To install the TouchPad, follow the steps below and refer to the figures in the preceding section:

1. With the top cover upside down, place the TouchPad, the Track Pad Bracket, and control button board in position.

2. Secure the TouchPad Bracket with one M2.5x3 screw.

3. Secure the control button board with two M2.5x3 black screws.

4. Connect the TouchPad FFC cable to the TouchPad.

4-42

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.15 System Board 4 Replacement Procedures

4.15 System Board

NOTE: There are two different SKUs of this model of computer – the Satellite M70 and the

Satellite Pro M70. Because =there exists some difference in how the system board is uninstalled. Differences are highlighted in the procedure.

Removing the System Board

To remove the system board, first remove the top cover, then follow the steps below:

1. Remove four M2x4 screws from the Express Bracket and remove two M2.5x3 screws from the

Express PC Board.

NOTE: The Satellite Pro M70 doesn’t have an Express PC Board, so skip this step.

2. Remove four M2.5x3 screws from the system board.

Figure 4-27 Removing the system board

NOTE: The Satellite Pro M70 only has two M2.5x3 screws.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-43

4 Replacement Procedures

3. Remove two hexagonal screws from the back of the system board.

4.15 Ssytem Board

Figure 4-28 Removing the hexagonal screws

4. Disconnect the speaker cable.

5. (Satellite Pro M70) Remove two M2.5x3 screws from the audio board, then lift it out.

Figure 4-29 Removing the audio board

4-44

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.15 System Board 4 Replacement Procedures

6. (Satellite Pro M70) Remove one M2.5x3 screw and one M2.5x12 screw from the ODD board, then lift it out.

Figure 4-30 Removing the ODD board

7. (Satellite Pro M70) Remove two M2.5x4 screws securing the fan and system board to the bottom cover chassis.

8. Lift out the system board.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-45

4 Replacement Procedures 4.15 Ssytem Board

Installing the System Board

To install the system board, follow the steps below and refer to the figures in the preceding section.

1. Seat the system board in the chassis.

2. (Satellite Pro M70) Secure the fan and system board to the bottom cover chassis with two

M2.5x4 screws.

3. (Satellit e Pro M70) Secure the ODD board with one M2.5x3 screw and one M2.5x12 screws.

4. (Satellite Pro M70) Secure the audio board with two M2.5x3 screws.

5. Secure two hexagonal screws to the back of the system board.

6. Secure four M2.5x3 screws to the system board.

NOTE: The Satellite Pro M70 only has two M2.5x3 screws.

7. Secure two M2.5x3 screws to the Express PC Board and four M2x4 screws to the Express

Bracket.

NOTE: The Satellite Pro M70 doesn’t have an Express PC Board, so skip this step.

4-46

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.15 Speakers 4 Replacement Procedures

4.16 Speakers

Removing the Speakers

To remove the speakers, first remove the top cover, system board and then follow the steps below:

1. Remove two M2.5x3 screws from the right speaker.

2. Remove two M2.5x3 screws from the left speaker.

Figure 4-31 Removing the speakers

3. Lift out the speakers.

Installing the Speakers

To install the speakers, follow the steps below and refer to the figure in the preceding section:

1. Seat each speaker.

2. Secure the left speaker with two M2.5x3 screws.

3. Secure the right speaker with two M2.5x3 screws.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-47

4 Replacement Procedures

4.17 VGA Board

Removing the VGA Board

To remove the VGA Board, first remove the system board.

NOTE: Satellite Pro M70 does not have a VGA board to remove.

1. Remove one M2.5x3 screw from the VGA board.

4.17 VGA Board

Figure 4-32 Removing the VGA Board-1

2. Disconnect the VGA board from the system board.

4-48

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.17 VGA Board 4 Replacement Procedures

3. On the bottom side of the VGA board, remove three M2.5x3 screws from the VGA board heat sink, then disengage it.

Figure 4-33 Removing the VGA Board-2

NOTE: The VGA board screws must be removed in a specific order, as shown above, to

prevent causing inadvertent damage to it.

Installing the VGA Board

To install the VGA board, follow the steps below and refer to the figures in the preceding section.

1. Connect the VGA board heat sink to the bottom of the VGA board.

NOTE: The VGA board screws must be tightened in a specific order, as shown above, to

prevent causing inadvertent damage to it.

2. Attach the VGA board to the system board.

3. Secure it with one M2.5x3 screw.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-49

4 Replacement Procedures

4.18 Thermal Module

Removing the Thermal Module

To remove the thermal module, first remove the VGA board.

1. Remove four M2.5x3 screws from the thermal module.

2. Pry off the thermal module while being careful of the thermal grease.

4.18 Thermal Module

Figure 4-34 Removing the Thermal Module

NOTE: After you remove the thermal module, be sure to replace the thermal grease on the

CPU when you reinstall it.

Installing the Thermal Module

To install the thermal module, follow the steps below and refer to the figures in the preceding section.

1. Restore the thermal grease to the top of the CPU.

2. Connect the thermal module, then secure it with four M2.5x3 screws.

4-50

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.19 Fan, CPU & Heat Sink 4 Replacement Procedures

4.19 Fan, CPU & Heat Sink

Removing the Fan, CPU & Heat Sink

To remove the Fan, Heat Sink and CPU, you must first remove the thermal module, then follow the steps below:

1. After removing the thermal module, remove the CPU by turning the marked cam to disengage the mechanism that locks the CPU in place and then lifting it out.

Figure 4-35 Removing the CPU

2. Disconnect the fan wire from the system board.

3. Remove two M2.5x6 fan screws from the top of the system board and one M2.5x3 fan screw from the bottom of the system board, and then lift out the fan.

Figure 4-36 Removing the fan

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-51

4 Replacement Procedures 4.19 Fan, CPU & Heat Sink

Figure 4-37 Removing the fan botton

4. On the top of the system board, remove two M2.5x3 screws from the heat sink cover.

Figure 4-38 Removing the heat sink

Note: The Satellite Pro M70 places the heat sink on the bottom of the system board.

4-52

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.19 Fan, CPU & Heat Sink 4 Replacement Procedures

Figure 4-39 Removing the heat sink

Installing the CPU

To install the CPU, follow the steps below and refer to the figures in the preceding section.

CAUTION: If you remove the heat sink, you should use the CPU grease tool to remove the grease on the CPU and heat sink. Reapply fresh grease before installing the heat sink.

1. Secure the heat sink cover with two rivets.

2. Secure the fan with two M2.5x6 fan screws on the top of the system board and one M2.5x3 fan screw on the bottom of the system board.

3. Connect the fan wire from the system board.

4. Reinstall the CPU, ensuring that you restore the thermal grease on its surface and then turn the cam back to the locked position.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-53

4 Replacement Procedures 4.20 Display Mask

4.20 Display Mask

Removing the Display Mask

To remove the display mask, first remove the display assembly as described earlier, then follow the steps below:

1. Remove the mask seals to expose four lower inner corner screws securing the display mask.

2. Remove four M2.5x6 black screws from the corners that were previously covered by the mask seals.

3. Carefully insert your fingers between the mask and the LCD panel and pry open the snaps.

Start with the four snaps at the top of the display mask. Continue unsnapping the display mask along the two sides and the bottom edge to remove display.

Figure 4-40 Removing the display mask

4-54

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.20 Display Mask 4 Replacement Procedures

Installing the Display Mask

To install the display mask, follow the steps below and refer to the figures in the preceding section.

1. Seat the display mask and secure the snaps on each side.

2. Secure the display mask with four M2.5x6 screws at the bottom inner corner.

3. Cover the secured screws with mask seals.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-55

4 Replacement Procedures 4.21 LCD Module

4.21 LCD Module

Removing the LCD Module

To remove the LCD module, first remove the display assembly and display mask, then follow the steps below.

1. Remove one M2.5x3 black screw and one M2x3 black screw securing the LCD cable and FL inverter board.

2. Disconnect the LCD cable from the FL inverter board.

3. Remove two M2.5x6 black screws securing the LCD module bracket to LCD cover.

4. Remove eight M2x3 black screws securing the LCD module bracket to the LCD module.

5. Lift it out.

Figure 4-41 Removing the LCD module-1

NOTE: If the LCD module malfunctions, remove the LCD cable and LCD bracket.

Then replace the whole LCD module unit.

4-56

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

4.21 LCD Module 4 Replacement Procedures

Installing the LCD Module

To install the LCD module, follow the steps below and refer to the figures in the preceding section.

1. Set the LCD module in the display assembly.

2. Connect the FL cable and the HV cable to the FL inverter board.

3. Set the LCD module in the display assembly with the LCD module bracket and eight M2x3 black screws. Secure the LCD mo dule with two M2.5x6 black screws.

4. Secure one M2.5x3 black screw and one M2x3 black screw holding the left HV cable and FL inverter board in place.

Satellite M70/Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

4-57

4 Replacement Procedures 4.22 FL Inverter Board

4.22 FL Inverter Board

Removing the FL Inverter Board

To remove the FL inverter board, first remove the battery pack, the display assembly, display mask, and LCD module, then follow the steps below.

1. Remove one M2.5x3 black screw and one M2x3 black screw securing the FL invert board to the LCD display assembly.

Figure 4-42 Removing the FL inverter board

Installing the FL Inverter Board

To install the FL inverter board, follow the steps below and refer to the figure in the preceding section..

1. Secure one M2.5x3 black screw and one M2x3 black screw connecting the FL inverter board to the LCD display assembly.

2. Reassemble the computer.

4-58

[CONFIDENTIAL]

Satellite M70/Satellite Pro M70 Series Maintenance Manual

Appendices

[CONFIDENTIAL]

Appendices

App-ii

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

Appendix Contents

Appendix A Handling the LCD Module ...............................................................................A-1

Appendix B Board Layout .....................................................................................................B-1

B.1 System Board (FRDSY*) Bottom View..........................................................................B-1

B.2 System Board (FRDSY*) Top View ...............................................................................B-2

Appendix C Pin Assignments .................................................................................................C-1

C.1 JP23/JP24 SODIMM I/F (200-PIN)................................................................................C-1

C.2 JP1/JP2 LCD I/F (22-pin) ................................................................................................C-5

C.3 JP14 RGB I/F (15-pin) .....................................................................................................C-6

C.4 JP10 HDD I/F (44-pin) ....................................................................................................C-7

C.5 JP28 ODD Module I/F (60-pin).......................................................................................C-8

C.6 JP13 Parallel I/F (25-pin) .................................................................................................C-9

C.7 JP26 PC Card I/F (84-pin) .............................................................................................C-10

C.8 JP19, JP22 Fan I/F (3-pin) .............................................................................................C-14

C.9 PCN1 AC Adaptor Connector (3-pin) ...........................................................................C-14

C.10 JP29 LINE IN (6-pin) ....................................................................................................C-14

C.11 JP30 Microphone (6-pin) ...............................................................................................C-15

C.12 JP31 Headphone (6-pin) ................................................................................................C-15

C.13 JP31 Headphone Connector (6-pin) ...............................................................................C-15

C.14 JP29 LINE-IN Connector (6-pin) ..................................................................................C-15

Appendix D Keyboard Scan/Character Codes.....................................................................D-1

Appendix E Key Layout ......................................................................................................... E-1

E.1 Japanese (JA) Keyboard .................................................................................................. E-2

Appendix F Series Screw Torque List .................................................................................. F-1

Appendix G Reliability............................................................................................................G-1

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

App-iii

Appendices

Figures

Figure B-1 System board (FRDSY*) layout (Bottom).......................................................... B-1

Figure B.2 System board (FRDSY*) layout (Top) ............................................................... B-2

Figure E-1 US keyboard .........................................................................................................E-1

Figure E-2 UK keyboard ........................................................................................................E-1

Figure E-3 SP keyboard..........................................................................................................E-2

Figure E-4 JA keyboard..........................................................................................................E-2

Figure E-5 KO keyboard ........................................................................................................E-3

Figure E-6 CF keyboard .........................................................................................................E-3

Figure E-7 Portuguese-ALPS keyboard .................................................................................E-4

Figure E-8 US-INTE_ALPS Keyboard ..................................................................................E-4

Figure E-9 GR keyboard ........................................................................................................E-5

Figure E-10 FR keyboard .........................................................................................................E-5

Figure E-11 CH keyboard ........................................................................................................E-6

Figure E-12 Swissc-Darfon keyboard ......................................................................................E-6

Figure E-13 IT new keyboard...................................................................................................E-7

App-iv

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

Tables

Table B-1 System board ICs (top and bottom) .....................................................................B-3

Table B-2 System board connectors (top and bottom) .........................................................B-4

Table C-1 SODIMM I/F pin assignments (200-PIN)...........................................................C-1

Table C-2 LCD I/F pin assignments (22-pin) .......................................................................C-5

Table C-3 RGB I/F pin assignments (15-pin).......................................................................C-6

Table C-4 HDD I/F pin assignments (44-pin) ......................................................................C-7

Table C-5 ODD I/F pin assignments (50-pin) ......................................................................C-8

Table C-6 Parallel I/F pin assignments (25-pin)...................................................................C-9

Table C-7 PC Card I/F pin assignments (84-pin) ...............................................................C-10

Table C-8 Mini PCI I/F pin assignments (124-pin) ............................................................C-12

Table C-9-1 JP18 Fan I/F pin assignments (3-pin) ................................................................C-14

Table C-9-2 JP21 Fan I/F pin assignments (3-pin) ................................................................C-14

Table C-10 AC Adaptor Connector pin assignments (3-pin) ...............................................C-14

Table C-11 Line in I/F pin assignments (6-pin) ..................................................................C-14

Table C-12 Microphone I/F pin assignments (6-pin) ...........................................................C-15

Table C-13 Microphone I/F pin assignments (6-pin) ...........................................................C-15

Table C-14 Headphone Connector pin assignments (6-pin).................................................C-15

Table C-15 Headphone Connector pin assignments (6-pin).................................................C-15

Table D-1 Scan codes (set 1 and set 2) .................................................................................D-1

Table D-2 Scan codes with left Shift key .............................................................................D-5

Table D-3 Scan codes in Numlock mode..............................................................................D-6

Table D-4 Scan codes with Fn key .......................................................................................D-6

Table D-5 Scan codes in overlay mode ................................................................................D-7

Table D-6 No.124 key scan code ..........................................................................................D-7

Table D-7 No.126 key scan code ..........................................................................................D-8

Table F-1 Series Screw Torque List ..................................................................................... F-1

Table G-1 MTBF ..................................................................................................................G-1

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

App-v

Appendix A

Appendix A Handling the LCD Module

Precautions for handling the LCD module

The LCD module can be easily damaged during assembly or disassembly. Therefore, please observe the following precautions when handling it:

1. When installing the LCD module in the LCD cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained.

2. Be careful to align the holes at the four corners of the LCD module with the corresponding holes in the LCD cover before securing the module with screws.

Do not force the module into place, because stress can affect its performance.

Note: The panel’s polarized surface is easily scarred, so handle it carefully.

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

A-1

3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again.

If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel.

4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it. Be sure to quickly wipe off any liquid.

A-2

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks.

6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module.

Satellite M70 /Satellite Pro M70 Series Maintenance Manual A-3

7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods.

8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage.

9. Do not disassemble the LCD module. Disassembly can cause malfunctions.

A-4

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization.

Satellite M70 /Satellite Pro M70 Series Maintenance Manual A-5

A-6

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

Appendix B

Appendix B Board Layout

B.1 System Board (FRDSY*) Top View

JP1 U5

JP2

U3

JP3

JP7

JP9

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

1

JP4

JP5

JP6

U9

U10

U14

JP8

U30

U17

JP18

JP19

JP 20

JP22

U28

JP24

JP13

PJP1

B.2 System Board (FRDSY*) Button View

JP12

JP11

PJP2

JP14

JP17

U2

JP28 JP29

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

2

JP16

JP15

JP21

JP23

JP25

JP23

JP24

JP25

JP28

JP29

PJP1

PJP2

JP11

JP12

JP13

JP14

JP15,16

JP17

JP18

JP19

JP20

JP21

JP22

JP3

JP4

JP5

JP6

JP7

JP8

JP9

Table B-1 System board connectors (top and bottom)

Number

JP1

JP2

Name

LCD conn

Speaker conn

SW/LED conn

TP conn

Keyboard conn

Bluetooth conn

Cardbus Socket

New card connector

5 in 1 conn

LAN connecto

USB conn1,2

CRT conn

VGA board Conn

DDR2 conn

FAN conn

CPU conn

TV-OUT conn

1394 conn

DVD-ROM conn

USB conn3

SATA HDD conn

MINI PCI

MDC conn

Microphone in jack

Headphone out jack

Power core conn

Battery conn

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

3

U5

U9

U10

U14

U17

U28

U30

Table B-2 System board ICs (top and bottom )

Number

U2

U3

Name

LAN transformer

LAN RTL8100CL

North bridge 915GM or 915PM

ICS951402AGT

South bridge ICH6

KB910

AC97 Codec_ALC250&MDC

PCI 7411 or PCI4510

BIOS RAM_SST39VF080-70

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

4

C .

Appendix C Pin Assignments

System Board

C.1 JP15,JP16

Table C-1 SODIMM I/F pin assignments (200-PIN) (1/4)

Pin No. Signal name

25

27

29

31

17

19

21

23

9

11

13

15

5

7

1

3

41

43

45

47

49

33

35

37

39

DQ2

DQ3

VSS

DQ8

DQ9

VSS

DQS1#

DQS1

VREF

VSS

DQ0

DQ1

VSS

DQS0#

DQS0

VSS

VSS

DQ10

DQ11

VSS

VSS

DQ16

DQ17

VSS

DQS2#

I/O

I/O

O

I/O

I/O

I/O

I/O

O

I/O

O

I/O

I/O

O

O

O

I/O

I/O

O

I/O

I/O

O

I/O

O

I/O

I/O

O

Pin No. Signal Name

26

28

30

32

18

20

22

24

10

12

14

16

6

8

2

4

42

44

46

48

50v

34

36

38

40

VSS

DQ12

DQ13

VSS

DM1

VSS

CK0

CK0#

VSS

DQ4

DQ5

VSS

DM0

VSS

DQ6

DQ7

VSS

DQ14

DQ15

VSS

VSS

DQ20

DQ21

VSS

NC

I/O

O

O

I/O

I/O

O

I/O

I/O

I/O

I/O

O

I/O

I/O

O

I/O

I/O

O

O

I/O

I/O

O

-

O

I/O

I/O

O

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

C-1

Table C-1 SODIMM I/F pin assignments (200-PIN) (2/4)

Pin No. Signal name

107

109

111

113

99

101

103

105

91

93

95

97

83

85

87

89

75

77

79

81

67

69

71

73

59

61

63

65

51

53

55

57

A3

A1

VDD

A10/AP

BAD

WE#

VDD

CAS#

NC

BA2

VDD

A12

A9

A8

VDD

A5

DM3

NC

VSS

DQ26

DQ27

VSS

CKE0

VDD

DQS2

VSS

DQ18

DQ19

VSS

DQ24

DQ25

VSS

Pin No. Signal Name

108

110

112

114

100

102

104

106

92

94

96

98

84

86

88

90

76

78

80

82

68

70

72

74

60

62

64

66

52

54

56

58

A2

A0

VDD

BA1

RAS#

S0#

VDD

ODT0

NC/A15

NC/A14

VDD

A11

A7

A6

VDD

A4

DM2

VSS

DQ22

DQ23

VSS

DQ28

DQ29

VSS

DQS3#

DQS3

VSS

DQ30

DQ31

VSS

NC/CKE1

VDD

I/O

I/O

I/O

O

I/O

I/O

I/O

O

I/O

I/O

I/O

O

I/O

-

I/O

O

I/O

I/O

O

I/O

O

I/O

-

O

I/O

O

I/O

I/O

O

I/O

O

I/O

I/O

I/O

I/O

I/O

O

I/O

I/O

I/O

O

I/O

I/O

I/O

O

I/O

-

-

O

I/O

I/O

O

I/O

O

I/O

I/O

O

I/O

O

I/O

I/O

O

I/O

O

I/O

I/O

C-2

[CONFIDENTIAL]

Satellite M70 Series Maintenance Manual

I/O

O

I/O

I/O

O

I/O

-

O

I/O

I/O

O

I/O

I/O

O

I/O

O

I/O

I/O

O

I/O

I/O

O

I/O

O

I/O

I/O

I/O

I/O

O

I/O

I/O

O

I/O

O

Pin No. Signal name

171

173

175

177

179

163

165

167

169

155

157

159

161

147

149

151

153

139

141

143

145

131

133

135

137

123

125

127

129

115

117

119

121

DM5

VSS

DQ42

DQ43

VSS

DQ48

DQ49

VSS

NC,TEST

VSS

DQS6#

DQS6

VSS

DQ50

DQ51

VSS

DQ56

DQS4

VSS

DQ34

DQ35

VSS

DQ40

DQ41

VSS

NC/S1#

VDD

NC/ODT1

VSS

DQ32

DQ33

VSS

DQS4#

Table C-1 SODIMM I/F pin assignments (200-PIN) (3/4)

Pin No. Signal Name

172

174

176

178

180

164

166

168

170

156

158

160

162

148

150

152

154

140

142

144

146

132

134

136

138

124

126

128

130

116

118

120

122

CK1

CK1#

VSS

DM6

VSS

DQ54

DQ55

VSS

DQ60

DQS5

VSS

DQ46

DQ47

VSS

DQ52

DQ53

VSS

VSS

DQ38

DQ39

VSS

DQ44

DQ45

VSS

DQS5#

NC/A13

VDD

NC

VSS

DQ36

DQ37

VSS

DM4

I/O

O

I/O

I/O

O

I/O

I/O

I/O

O

I/O

O

I/O

I/O

O

I/O

O

I/O

I/O

I/O

I/O

O

I/O

O

I/O

I/O

O

I/O

I/O

O

I/O

I/O

O

-

O

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

C-3

Table C-1 SODIMM I/F pin assignments (200-PIN) (4/4)

Pin No. Signal name

189

191

193

195

181

183

185

187

197

199

DQ57

VSS

DM7

VSS

DQ58

DQ59

VSS

SDA

SLC

VDDSPD

I/O

I/O

I/O

O

I/O

I/O

O

I/O

O

I/O

O

Pin No. Signal Name

190

192

194

196

182

184

186

188

198

200

DQ61

VSS

DQS7#

DQS7

VSS

DQ62

DQ63

VSS

SA0

SA1

I/O

O

I/O

I/O

O

I/O

O

I/O

I/O

O

O

C-4

[CONFIDENTIAL]

Satellite M70 Series Maintenance Manual

C.2 JP13

Table C-2 RGB I/F pin assignments (15-pin)

Pin No. Signal name

9

11

13

15

5

7

1

3

CRT_R_L

CRT_B_L

GND

GND

+CRT_VCC

NC

CRT_HSYNC_L

DSUB_15

I/O Pin No.

-

-

O

I/O

O

O

-

-

10

12

14

6

8

2

4

Signal Name

CRT_G_L

GND

GND

GND

GND

DSUB_12

CRT_VSYNC_L

I/O

-

I/O

O

-

-

O

-

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

C-5

C.3 JP23

Table C-3 HDD I/F pin assignments (44-pin)

Pin No. Signal name

9

11

13

15

5

7

1

3

17

19

21

GND

A-

B-

GND

VCC3.3

GND

GND

VCC5

GND

GND

NC

I/O Pin No. Signal Name

10

12

14

16

6

8

2

4

18

20

22

A+

GND

B+

VCC3.3

VCC3.3

GND

VCC5

VCC5

NC

NC

NC

I/O

-

C-6

[CONFIDENTIAL]

Satellite M70 Series Maintenance Manual

C.4 JP21

Table C-4 ODD I/F pin assignments (52-pin)

Pin No.

25

27

29

31

17

19

21

23

9

11

13

15

5

7

1

3

41

43

45

47

33

35

37

39

49

51

Signal name

INT_CD_L

CD_AGND

IDE_ODDRST#

IDE_DD7

IDE_DD6

IDE_DD5

IDE_DD4

IDE_DD3

IDE_DD2

IDE_DD1

IDE_DD0

GND

IDE_DIOW#

IDE_DIORDY

IDE_IRQ

IDE_DA1

IDE_DA0

IDE_DCS1#

SHDD_LED#

+5VS

+5VS

GND

GND

SD_CSEL

NC

NC

I/O

O

I

I

O

I/O

I/O

I/O

-

I/O

I/O

I/O

I/O

I

-

O

I/O

-

-

-

-

O

O

I

-

-

Signal Name

INT_CD_R

NC

IDE_DD8

IDE_DD9

IDE_DD10

IDE_DD11

IDE_DD12

IDE_DD13

IDE_DD14

IDE_DD15

IDE_DDREQ

IDE_DIOR#

GND

IDE_DDACK#

NC

+5VCD

IDE_DA2

IDE_DCS3#

+5VCD

+5VCD

+5VCD

GND

GND

GND

NC

NC

Pin No.

26

28

30

32

18

20

22

24

10

12

14

16

6

8

2

4

42

44

46

48

34

36

38

40

50

52

I/O

O

O

O

I

I/O

I/O

I

O

I/O

I/O

I/O

I/O

I

-

I/O

I/O

-

-

-

-

O

-

I

-

-

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

C-7

C.5 JP7

I/O

I

I

I

I

I

I

I

I

I

I

I

I

-

-

I

I

I

O

I/O

I

I

I

I/O

I/O

I/O

I

-

I/O

I/O

I/O

Pin No. Signal name

25

26

27

28

29

30

21

22

23

24

17

18

19

20

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

+S1_VCC

+S1_VPP

S1_A16

S1_A15

S1_A12

S1_A7

S1_A6

S1_A5

S1_A4

S1_A3

S1_A2

S1_A1

S1_A0

S1_D0

GND

S1_D3

S1_D4

S1_D5

S1_D6

S1_D7

S1_CE1#

S1_A10

S1_OE#

S1_A11

S1_A9

S1_A8

S1_A13

S1_A14

S1_WE#

S1_RDY#

Table C-5 PC Card I/F pin assignments (68-pin) (1/2)

Pin No. Signal Name

59

60

61

62

63

64

55

56

57

58

51

52

53

54

47

48

49

50

43

44

45

46

39

40

41

42

35

36

37

38

+S1_VCC

+S1_VPP

S1_A22

S1_A23

S1_A24

S1_A25

S1_VS2

S1_RST

S1_WAIT#

S1_INPACK#

S1_REG#

S1_BVD2

S1_BVD1

S1_D8

GND

S1_CD1#

S1_D11

S1_D12

S1_D13

S1_D14

S1_D15

S1_CE2#

S1_VS1

S1_IORD#

S1_IOWR#

S1_A17

S1_A18

S1_A19

S1_A20

S1_A21

I/O

I

O

I

O

I

I/O

I

I

I

I

I

I

-

-

I

I

I

I

I

I/O

I

I

I/O

I/O

I/O

I/O

-

O

I/O

I/O

C-8

[CONFIDENTIAL]

Satellite M70 Series Maintenance Manual

Table C-5 PC Card I/F pin assignments (88-pin) (2/2)

Pin No. Signal name

31

32

33

34

S1_D1

S1_D2

S1_WP

GND

I/O

I/O

I/O

I/O

-

Pin No. Signal Name

65

66

67

68

S1_D9

S1_D10

S1_CD2#

GND

I/O

I/O

I/O

I

-

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

C-9

C.6 JP24

Table C-6 Mini PCI I/F pin assignments (126-pin) (1/2)

Signal name

PCI_AD31

PCI_AD29

GND

PCI_AD27

PCI_AD25

NC

PCI_CBE3#

PCI_AD23

GND

PCI_AD21

PCI_AD19

GND

PCI_AD17

PCI_CBE2#

NC

NC

NC

NC

NC

NC

SWITCH

NC

PCI_PIRQH#

+3V

NC

GND

CLK_PCL_MINI

GND

PCI_REQ1#

+3V

Pin No.

49

51

53

55

57

59

41

43

45

47

33

35

37

39

25

27

29

31

17

19

21

23

9

11

13

15

5

7

1

3

I/O

-

I/O

I/O

-

I/O

I/O

I/O

-

I/O

I/O

I/O

I/O

-

I/O

O

-

I

O

-

-

I

O

-

-

O

-

-

-

-

-

Pin No. Signal Name I/O

50

52

54

56

58

60

42

44

46

48

34

36

38

40

26

28

30

32

18

20

22

24

10

12

14

16

6

8

2

4

MINI_PME#

NC

PCI_AD30

+3VS

PCI_AD28

PCI_AD26

PCI_AD24

MINI_IDSEL

GND

PCI_AD22

PCI_AD20

PCI_PAR

PCI_AD18

PCI_AD16

NC

NC

NC

NC

NC

NC

NC

NC

+5VS

PCI_PIRQG#

NC

+3VALW

PCI_RST#

+3VS

PCI_GNT1#

GND

-

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I

-

I/O

O

O

O

O

-

-

I

-

O

-

-

-

-

-

-

-

-

C-10

[CONFIDENTIAL]

Satellite M70 Series Maintenance Manual

Table C-6 Mini PCI I/F pin assignments (124-pin)(2/2)

Pin No. Signal name

117

119

121

123

125

109

111

113

115

101

103

105

107

93

95

97

99

85

87

89

91

77

79

81

83

69

71

73

75

61

63

65

67

NC

NC

GND

NC

GND

GND

NC

+5VS

NC

NC

PCI_AD3

+5VS

PCI_AD1

GND

NC

NC

NC

PCI_IRDY#

+3V

PM_CLKRUN#

PCI_SERR#

GND

PCI_PERR#

PCI_C/BE1#

PCI_AD14

GND

PCI_AD12

PCI_AD10

GND

PCI_AD8

PCI_AD7

+3V

PCI_AD5

I/O

-

-

-

-

-

-

-

I

-

-

-

-

-

I/O

O

I/O

I/O

I/O

O

I/O

-

I/O

I/O

-

-

O

I/O

I/O

I/O

O

I/O

I/O

Pin No. Signal Name

118

120

122

124

126

110

112

114

116

102

104

106

108

94

96

98

100

86

88

90

92

78

80

82

84

70

72

74

76

62

64

66

68

PCI_AD2

PCI_AD0

NC

NC

GND

NC

NC

NC

NC

NC

GND

NC

GND

GND

NC

+3VALW

NC

GND

PCI_FRAME#

PCI_TRDY#

PCI_STOP#

+3VS

PCI_DEVSEL#

GND

PCI_AD15

PCI_AD13

PCI_AD11

GND

PCI_AD9

PCI_BE0#

+3VS

PCI_AD6

PCI_AD4

I/O

-

-

-

-

-

-

-

-

-

-

-

-

I/O

I/O

-

-

I/O

O

I/O

I/O

I/O

I/O

-

I/O

O

I/O

-

I/O

-

I/O

I/O

I/O

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

C-11

C.7 JP1

17

18

19

20

13

14

15

16

9

10

11

12

7

8

5

6

Pin No.

3

4

1

2

25

26

27

28

21

22

23

24

29

30

Signal name

GND

GND

GMCH_TXCLK-

GND

GMCH_TXCLK+

NC

GND

+VCDVDD_LCD

GMCH_TXOUT0-

+VCDVDD_LCD

GMCH_TXOUT0+

+3VS_LCD

GND

GND

Panel Clock Signals

GND

Panel Clock Signals

Non-Connection

GND

Power for Panel

Panel Data Signals

Power for Panel

Panel Data Signals

Power for Panel

GND

+3VS_LCD

GMCH_TXOUT2-

GMCH_CLD_CLK

GND

Power for Panel

Panel Data Signals

DDC Clock

GMCH_TXOUT2+ Panel Data Signals

GMCH_CLD_DATA DDC DATA

GND

DAC_BRIG

GND

Inverter Control signal

GMCH_TXOUT1-

INVT_PWM

GMCH_TXOUT1+

DISPOFF#

GND

NC

GND

INVPWR+B

GND

INVPWR+B

Panel Data Signals

Inverter Control signal

Panel Data Signals

LCD back light

GND

Non-Connection

GND

Inverter Control signal

GND

Inverter Control signal

Function

C-12

[CONFIDENTIAL]

Satellite M70 Series Maintenance Manual

C.8 JP17

Table C-8 JP8 Fan I/F pin assignments (3-pin)

Pin No. Signal name

1

3

+FAN1_VOUT

GND

C.9 PJP1

I/O

I

-

Pin No. Signal Name

2 FANSPEED1

Table C-9 AC Adaptor Connector pin assignments (4-pin)

I/O

O

Pin No. Signal name

1

3

DC_IN_S2

GND

I/O

I

-

Pin No. Signal Name

2

4

DC_IN_S2

GND

I/O

-

-

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

C-13

C.10 JP28

Table C-10 Microphone I/F pin assignments (6-pin)

Pin No.

1

3

5

Signal name

GND

+AUD_VREF_J

NC

C.11 JP29

I/O

-

I

-

Pin No. Signal Name

2

4

6

MIC-1

NC

NC

Table C-11 Headphone Connector pin assignments (6-pin)

I/O

I

-

-

Pin No. Signal name

1

3

5

GND

INTSPK_R1

GND

I/O

-

O

-

Pin No. Signal Name

2

4

6

INTSPK_L1

NBA_PLUG

NC

I/O

O

I

-

C-14

[CONFIDENTIAL]

Satellite M70 Series Maintenance Manual

Appendix D

Appendix D Keyboard Scan/Character Codes

Cap

No.

16

17

18

19

11

12

13

15

07

08

09

10

01

02

03

04

05

06

24

25

26

27

28

20

21

22

23

0 )

- _

= +

BkSp

Tab

Q

W

E

‘ ~

1 !

2 @

3 #

4 $

5 %

6 ^

7 &

8 *

9 (

I

O

P

[ {

] }

R

T

Y

U

Table D-1 Scan codes (set 1 and set 2) (1/4)

Keytop

Code set 1

Make Break Make

0F

10

11

12

0B

0C

0D

0E

07

08

09

0A

29

02

03

04

05

06

17

18

19

1A

1B

13

14

15

16

8F

90

91

92

8B

8C

8D

8E

87

88

89

8A

A9

82

83

84

85

86

97

98

99

9A

9B

93

94

95

96

0D

15

1D

24

45

4E

55

66

36

3D

3E

46

0E

16

1E

26

25

2E

43

44

4D

54

5B

2D

2C

35

3C

Code set 2

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

Break

0D

15

1D

24

45

4E

55

66

36

3D

3E

46

0E

16

1E

26

25

2E

43

44

4D

54

5B

2D

2C

35

3C

Note

*2

*2

*2

*2

*2

*2

*2

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

D-1

Table D-1 Scan codes (set 1 and set 2) (2/4)

50

51

52

53

46

47

48

49

54

55

57

Cap

No.

41

43

44

45

37

38

39

40

33

34

35

36

29

30

31

32

Keytop

B

N

M

, <

Z

X

C

V

. >

/ ?

Shift (R)

\ |

Caps Lock

A

S

D

F

G

H

J

K

L

; :

‘ “

Enter

Shift (L)

No.102 key

Code set 1

Make Break Make

Code set 2

Break

28

1C

2A

56

24

25

26

27

20

21

22

23

2B

3A

1E

1F

A8

9C

AA

D6

A4

A5

A6

A7

A0

A1

A2

A3

AB

BA

9E

9F

52

5A

12

61

3B

42

4B

4C

23

2B

34

33

5D

58

1C

1B

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

52

5A

12

61

3B

42

4B

4C

23

2B

34

33

5D

58

1C

1B

2C

2D

2E

2F

30

31

32

33

34

35

36

AC

AD

AE

AF

B0

B1

B2

B3

B4

B5

B6

1A

22

21

2A

32

31

3A

41

49

4A

59

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

32

31

3A

41

1A

22

21

2A

49

4A

59

Note

*2

*2

*2

*2

*3

*2

*2

*2

*2

*5

D-2

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

Cap

No.

85

86

89

110

80

81

83

84

64

75

76

79

58

60

61

62

112

113

114

115

116

117

118

119

120

121

Table D-1 Scan codes (set 1 and set 2) (3/4)

Keytop

Code set 1

Make Break Make

Code set 2

Break

F5

F6

F7

F8

F1

F2

F3

F4

F9

F10

Ctrl(R)

Ins

Del

? ?

Home

End

? ?

? ?

PgUp

PgDn

? ?

Esc

Ctrl(L)

Alt (L)

1D

38

9D

B8

14

11

F0

F0

14

11

Space 39 B9 29 F0 29

ALT (R) E0 38 E0 B8 E0 11 E0 F0 11

E0 1D E0 9D E0 14 E0 F0 14

E0 52 E0 D2 E0 70 E0 F0 70

E0 53 E0 D3 E0 71 E0 F0 71

E0 4B E0 CB E0 6B E0 F0 6B

E0

E0

E0

E0

E0

E0

E0

47

4F

48

50

49

51

4D

01

E0

E0

E0

E0

E0

E0

E0

C7

CF

C8

D0

C9

D1

CD

81

E0

E0

E0

E0

E0

E0

E0

6C

69

75

72

7D

7A

74

76

E0

E0

E0

E0

E0

E0

E0

F0

F0

F0

F0

F0

F0

F0

F0

6C

69

75

72

7D

7A

74

76

3B

3C

3D

3E

3F

40

41

42

43

44

BB

BC

BD

BE

BF

C0

C1

C2

C3

C4

05

06

04

0C

03

0B

83

0A

01

09

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

05

06

04

0C

03

0B

83

0A

01

09

Note

*1

*1

*1

*1

*1

*1

*1

*1

*1

*1

*3

*3

*3

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

D-3

Table D-1 Scan codes (set 1 and set 2) (4/4)

Cap

No.

122

123

124

126

X

X x

Keytop

Code set 1

Make Break Make

Code set 2

Break

F11

F12

57

58

D7

D8

78

07

F0

F0

PrintSc *6

Pause

Fn

Win

*7

*6

*7

*6

*7

*6

*7

— — — —

E0 5B E0 DB E0 1F E0 F0

App E0 5D E0 DD E0 2F E0 F0

78

07

1F

2F

Note

*4

*3

*3

*6

*7

Notes:

1. * Scan codes differ by mode.

2. * Scan codes differ by overlay function.

3. * Combination with the Fn key gives different codes.

4. * The Fn key does not generate a code by itself.

5. * This key corresponds to key No. 42 in a 102-key model.

6. * Refer to Table D-6, No. 124 key scan code.

7. * Refer to Table D-7, No. 126 key scan code.

D-4

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

Table D-2 Scan codes with left Shift key

Cap

No.

Key top

Make

Code set 1

Break

Code set 2

Make Break

55

75

/

INS

E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12

E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12

76

79

DEL E0 AA E0 53 E0 D3 E0 2A E0 F0 12 E0 71 E0 F0 71 E0 12

? ?

E0 AA E0 4B E0 CB E0 2A E0 F0 12 E0 6B E0 F0 6B E0 12

80 Home E0 AA E0 47 E0 C7 E0 2A E0 F0 12 E0 6C E0 F0 6C E0 12

81

83

84

End E0 AA E0 4F E0 CF E0 2A E0 F0 12 E0 69 E0 F0 69 E0 12

? ?

E0 AA E0 48 E0 C8 E0 2A E0 F0 12 E0 75 E0 F0 75 E0 12

? ?

E0 AA E0 50 E0 D0 E0 2A E0 F0 12 E0 72 E0 F0 72 E0 12

85 PgUp E0 AA E0 49 E0 C9 E0 2A E0 F0 12 E0 7D E0 F0 7D E0 12

86 PgDn E0 AA E0 51 E0 D1 E0 2A E0 F0 12 E0 7A E0 F0 7A E0 12

89

? ?

E0 AA E0 4D E0 CD E0 2A E0 F0 12 E0 74 E0 F0 74 E0 12

X Win E0 AA E0 5B E0 DB E0 2A E0 F0 12 E0 1F E0 F0 1F E0 12

X App E0 AA E0 5D E0 DD E0 2A E0 F0 12 E0 2F E0 F0 2F E0 12

Note : The table above shows scan codes with the left Shift key. In combination with the right Shift key, scan codes are changed as listed below:

Set 1

Set 2

With left Shift With right Shift

E0 AA ___________ E0 B6

E0 2A ___________ E0 36

E0 F0 12_________ E0 F0 59

E0 12____________ E0 59

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

D-5

Table D-3 Scan codes in Numlock mode

Cap

No.

Key top

Make

Code set 1

Break Make

Code set 2

Break

86

89

X

X

75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12

76

79

DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12

? ?

E0 2A E0 4B E0 CB E0 AA E0 12 E0 6B E0 F0 6B E0 F0 12

80 Home E0 2A E0 47 E0 C7 E0 AA E0 12 E0 6C E0 F0 6C E0 F0 12

81

83

84

85

End E0 2A E0 4F E0 CF E0 AA E0 12 E0 69 E0 F0 69 E0 F0 12

? ?

? ?

E0 2A E0 48 E0 C8 E0 AA E0 12 E0 75 E0 F0 75 E0 F0 12

E0 2A E0 50 E0 D0 E0 AA E0 12 E0 72 E0 F0 72 E0 F0 12

PgUp E0 2A E0 49 E0 C9 E0 AA E0 12 E0 7D E0 F0 7D E0 F0 12

PgDn E0 2A E0 51 E0 D1 E0 AA E0 12 E0 7A E0 F0 7A E0 F0 12

? ?

E0 2A E0 4D E0 CD E0 AA E0 12 E0 74 E0 F0 74 E0 F0 12

Win E0 2A E0 5B E0 DB E0 AA E0 12 E0 1F E0 F0 1F E0 F0 12

App E0 2A E0 5D E0 DD E0 AA E0 12 E0 2F E0 F0 2F E0 F0 12

Cap

No.

43

58

60

121

122

123

Keytop

ENT

L-CTRL

L-ALT

ARROW

NUMERIC

Scrl

Table D-4 Scan codes with Fn key

Code set 1

Make Break

E0

E0

E0

1C

1D

38

45

45

46

E0

E0

E0

9C

9D

B8

C5

C5

C 6

Make

Code set 2

Break

E0 5A E0

E0 14 E0

F0

F0

5A

14

E0 11 E0

77 F0

F0 11

77

77

7E

F0

F0

77

7E

D-6

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

Table D-5 Scan codes in overlay mode

Cap

No.

38

39

40

52

54

55

24

25

26

37

09

10

11

23

Keytop

K

L

;

M

.

/

I

O

P

J

8

9

0

U

(2)

(3)

(+)

(0)

(.)

(/)

(5)

(6)

(–)

(1)

(8)

(9)

(*)

(4)

Make

Code set 1

Break

4C

4D

4A

4F

48

49

37

4B

50

51

4E

52

53

CC

CD

CA

CF

C8

C9

B7

CB

D0

D1

CE

D2

D3

E0 35 E0 B5

Make

Code set 2

Break

73

74

7B

69

75

7D

7C

6B

72

7A

79

70

71 F0

E 0 4A E0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

F0

72

7A

79

70

71

F0 4A

73

74

7B

69

75

7D

7C

6B

Table D-6 No.124 key scan code

Key top

Shift

Code set 1 Code set 2

Make Break Make Break

Prt Sc Common E0 2A E0 37 E0 B7 E0 AA E0 12 E0 7C E0 F0 7C E0 F0 12

Ctrl

?

Shift

?

Alt

?

E0 37

E0 37

54

E0 B7

E0 B7

D4

E0 7C

E0 7C

84

E0 F0 7C

E0 F0 7C

F0 8 4

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

D-7

Table D-7 No.126 key scan code

Key top Shift Code set 1

Make

Code set 2

Make

Pause Common E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77

Ctrl E0 46 E0 C6 E0 7E E0 F0 7E

*: This key generates only make codes.

D-8

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

Appendix E

Appendix E Key Layout

E.1 United States (US) Keyboard

Figure E-1 US keyboard

E.2 United Kingdom (UK) Keyboard

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

E-1

Figure E-2 UK keyboard

E-2

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

E.3 Spanish (SP) Keyboard

E.4 Japanese (JA) Keyboard

Figure E-3 SP keyboard

Figure E-4 JA keyboard

Satellite M70 /Satellite Pro M70 Series Maintenance Manual E-3

E.5 Korean (KO) Keyboard

Figure E-5 KO keyboard

E.6 Canada France (CF) Keyboard

E-4

Figure E-6 CF keyboard

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

E.7 Portuguese (PO) Keyboard

Figure E-7 PO keyboard

Satellite M70 /Satellite Pro M70 Series Maintenance Manual E-5

E.8 US-INTE (UI/INTE) Keyboard

E.9 Germanic (GR) Keyboard

Figure E-8 U S-INTE_ALPS Keyboard

E-6

[CONFIDENTIAL]

Figure E-9 GR keyboard

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

E.10 France (FR) Keyboard

E.11 Chinese (CH) Keyboard

Figure E-10 FR keyboard

Figure E-11 CH keyboard

Satellite M70 /Satellite Pro M70 Series Maintenance Manual E-7

E.12 Swissc-Darfon(SG) Keyboard

Figure E -12 Swissc-Darfon keyboard

E-8

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

E.13 Italian (IT) Keyboard

E.14 Be lgiun (BE) Keyboard

Figure E-13 IT keyboard

Figure E-14 BE keyboard

Satellite M70 /Satellite Pro M70 Series Maintenance Manual E-9

E.15 Arabic (AR-E) Keyboard

Figure E-15 AR-E keyboard

E-10

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

E.16 Czech (CZ) Keyboard

Figure E-16 CZ keyboard

Satellite M70 /Satellite Pro M70 Series Maintenance Manual E-11

E.17 Estonian (EST) Keyboard

E.18 Greek (GK) Keyboard

Figure E -17 ES T keyboard

E-12

Figure E-18 GK keyboard

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

E.19 Hebrew (HB) Keyboard

E.20 Hungary (HG) Keyboard

Figure E-19 HB keyboard

Figure E -20 HG Keyboard

Satellite M70 /Satellite Pro M70 Series Maintenance Manual E-13

E.21 Norwegian (NW) Keyboard

E.22 Dutch (DT) Keyboard

Figure E-21 NW keyboard

E-14

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

E.23 Lithuanian (LIT) Keyboard

Figure E-22 DT keyboard

Figure E-23 LIT keyboard

Satellite M70 /Satellite Pro M70 Series Maintenance Manual E-15

E.24 Russian (RU) Keyboard

E.25 Turkish (TR) Keyboard

Figure E-24 RU keyboard

E-16

[CONFIDENTIAL]

Figure E-25 TR keyboard

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

E.26 Yugoslavian (YU) Keyboad

E.27 Danish (DM) Keyboard

Figure E-26 YU keyboard

Satellite M70 /Satellite Pro M70 Series Maintenance Manual E-17

E.28 Slovak (SA) Keyboard

Figure E -27 DM keyboard

Figure E-28 SR keyboard

E-18

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

E.29 Swedish (SD) Keyboard

E.30 Swiss (SW) Keyboard

Figure E-29 SD keyboard

Figure E-30 SW keyboard

Satellite M70 /Satellite Pro M70 Series Maintenance Manual E-19

E.31 Japanese (JA FLAT GRAY ) Keyboard

Figure E-31 JA(f lat gray) keyboard

E.32 Japanese (JA BIG FLAT GRAY) Keyboard

E-20

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

Figure E-32 JA(big flat gray) keyboard

E.33 Japanese (JA FLAT black) Keyboard

Figure E-33 JA(flat black) keyboard

Satellite M70 /Satellite Pro M70 Series Maintenance Manual E-21

Appendix G

Appendix F Series Screw Torque List

Table F-1 Series Screw Torque List

SCREW P/N

LCD ASSY

MAAA0015320

MAC925006Z0

SCREW SPEC

M2X3

M2.5X6

MAAA0015320

MAC925003Z0

M2X3

M2.5X3

MAC925006Z0

MB ASSY

MAC925003Z0

MAC925006Z0

MAC925003Z0

MAC925003Z0

MAC925003Z0

HDD ASSY

MAAA4303000

M2.5X6

M3X3

ODD MODULE SUB ASSY

MAAA0015320 M2X3

LOG UPPER SUB ASSY

MAC925003Z0 M2.5X3

MAC925003Z0 M2.5X3

M2.5X3

M2.5X6

M2.5X3

M2.5X3

M2.5X3

MAC925003Z0 M2.5X3

MAC925003Z0 M2.5X3

LOGIC LOWER SUB ASSY

MAC925003Z0

M2.5X3

Q'ty LOCATION

8

2

1

1

4

LCD BRK TO LCD PANEL

LCD PANEL ASSY TO

COVER SUB ASSY (R+L)

INVERTER TO COVER

SUB ASSY

LCD CABLE TO COVER

SUB ASSY

LCD BEZEL TO COVER

SUB ASSY

1 THERMAL FAN TO MB

2 THERMAL FAN TO MB

4 THERMAL FIN TO MB

1

3

VGA BOARD TO MB

VGA HEAT SINK TO VGA

BOARD

4

HDD BRACKET L/R TO

HDD MODULE

2

MODULE LOCK BRACKET

TO XDROM MODULE

3

1

3

2

HINGE SADDLE (L+R) TO

UPPER

TRACK PAD BRACKET

TO LOGIC UPPER

SWITCH BOARD TO

LOGIC UPPER

TP BOARD TO LOGIC

UPPER

4

SPEAKER TO LOGIC

LOWER(L/R)

SCREW TORQUE

1.5~2.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

3.0~3.5kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

Satellite M70 Series Maintenance Manual

[CONFIDENTIAL]

F-2

MAC925003Z0

MAC925003Z0

MAC925006Z0

MACK25001Z0

MAC925003Z0

MAC925003Z0

MAC925006Z0

MAAA0015320

MAAA0015320

MAC925003Z0

MAC925003Z0

MACA2500150

MACK25001Z0

MAC925006Z0

MACK25080Z0

MAFA94001N0

LOGIC ASSY

MAC925003Z0 M2.5X3

M2.5X3

M2.5X3

M2.5X6

M2.5X12

M2.5X3

M2.5X3

M2.5X6

M2X3

M2X3

M2.5X3

M2.5X3

M2X4

M2.5X12

M2.5X6

M2.5X8

HEXAGONAL NUT

4

2

2

2

1

4

2

2

2

2

2

2

1

13

1

4

2

MB ASSY TO LOGIC

LOWER

MB_BKT_ASSY TO

LOWER

LOGIC UPPER TO MB

ASSY

LOGIC UPPER TO MB

ASSY

LOGIC UPPER TO MB

ASSY

MB ASSY TO LOGIC

LOWER

EXPRESS BOARD TO

LOWER

LCD ASSY TO LOGIC

UPPER ASSY

BLUETOOTH TO MB

KEYBOARD TO LOGIC

ASSY

HDD MODULE SUB ASSY

TO LOGIC LOWER

MDC BOARD TO LOGIC

MINI PCI DOOR ASSY TO

LOGIC LOWER

LOGCLOWER TO LOGIC

UPPER

XDROM ASSY TO LOGIC

ASSY

LOGCLOWER TO LOGIC

UPPER

VGA PORT TO LOGIC

ASSY

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

3.0~3.5kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

2.5~3.0kg

F-3

[CONFIDENTIAL]

Satellite M70 Series Maintenance Manual

Appendix G

Appendix G Reliability

The following table shows MTBF (Mean Time Between Failures) for each component.

Table G-1 MTBF

Component

LCD

Keyboard

HDD

Removable FDD

Optical (DVD/CD) drive

AC adaptor

Time (hours)

10,000

60,000

300,000

30,000

60,000

100,000

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

[CONFIDENTIAL]

G-1

G-2

[CONFIDENTIAL]

Satellite M70 /Satellite Pro M70 Series Maintenance Manual

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents